Basics for understanding the project a dc convertor can be used as a dc transformer to step up po step down a fixed ac voltage.

voltage. Convertors can also be used as regulators for transferring energy between two dc sources Harmonics are generated at the input and at the load side of the convertor Harmonics are reduced by filters A convertor can operate either at fixed freq or at variable frequency Variable frequency convertor operation is difficult as it generates harmonics of variable frequencies and so filter design becomes difficult To reduce the size of the filters and to lower the ripple current chopping frequency should be high The regulation is normallyachieved by using a PWM at a fixed frequency and the switching devices normally used is IGBT ,MOSFET,BJT. Buck boost convertors(pg 194-rashid-pearson publication) The voltage may be less than or greater than input voltage Output polarity is opposite to that of input voltage(also known as inverting regulator Polarity reversal is obtained without a transformer Has high efficiency. Fault current is limited by the inductor Output short circuit current is easy to implement Input current is discontinuous High peak current flows through the transistor

Performance parameters of a convertor Power semiconductor devices require a min time to turn on and turn off therefore the duty cycle can be controlled only between the maximum and minium value thereby limiting the minimum value of output voltage The performance parameters are as follows 1. Ripple current of the inductor 2. Maximum switching frequency 3. Conduction for continuous or discontinuous inductor current 4. Minimum value of inductor to maintain continuous inductor current 5. Ripple current of the output voltage and output current 6. Ripple current of the input current

Power electronics is the application of solid-state electronics for the control and conversion of electric power. It also refers to a subject of research in electrical engineering which deals with design, control, computation and integration of nonlinear, time varying energy processing electronic systems with fast dynamics. Contents [hide]

1 Introduction 2 Switching 3 Applications 4 See also 5 References 6 External links

[edit] Introduction Power electronic converters can be found wherever there is a need to modify a form of electrical energy (i.e. change its voltage, current or frequency). The power range of these converters is from some milliwatts (as in a mobile phone) to hundreds of megawatts (e.g. in a HVDC transmission system). With "classical" electronics, electrical currents and voltage are used to carry information, whereas with power electronics, they carry power. Thus, the main metric of power electronics becomes the efficiency. The first very high power electronic devices were mercury-arc valves. In modern systems the conversion is performed with semiconductor switching devices such as diodes, thyristors and transistors, as pioneered by R. D. Middlebrook and others beginning in the 1950s. In contrast to electronic systems concerned with transmission and processing of signals and data, in power electronics substantial amounts of electrical energy are processed. An AC/DC converter (rectifier) is the most typical power electronics device found in many consumer

electronic devices, e.g. television sets, personal computers, battery chargers, etc. The power range is typically from tens of watts to several hundred watts. In industry the most common application is the variable speed drive (VSD) that is used to control an induction motor. The power range of VSDs start from a few hundred watts and end at tens of megawatts. The power conversion systems can be classified according to the type of the input and output power

AC to DC (rectifier) DC to AC (inverter) DC to DC (DC to DC converter) AC to AC (AC to AC converter)

[edit] Switching As efficiency is at a premium in a power electronic converter, the losses that a power electronic device generates should be as low as possible. The instantaneous dissipated power of a device is equal to the product of the voltage across the device and the current through it ( ). From this, one can see that the losses of a power device are at a minimum when the voltage across it is zero (the device is in the On-State) or when no current flows through it (Off-State). Therefore, a power electronic converter is built around one (or more) device operating in switching mode (either On or Off). With such a structure, the energy is transferred from the input of the converter to its output by bursts. [edit] Applications Power electronic systems are found in virtually every electronic device. For example:

DC/DC converters are used in most mobile devices (mobile phones, PDA etc.) to maintain the voltage at a fixed value whatever the voltage level of the battery is. These converters are also used for electronic isolation and power factor correction. AC/DC converters (rectifiers) are used every time an electronic device is connected to the mains (computer, television etc.). These may simply change AC to DC or can also change the voltage level as part of their operation. AC/AC converters are used to change either the voltage level or the frequency (international power adapters, light dimmer). In power distribution networks AC/AC converters may be used to exchange power between utility frequency 50 Hz and 60 Hz power grids. DC/AC converters (inverters) are used primarily in UPS or renewable energy systems or emergency lighting systems. When mains power is available, it will charge the DC battery. If the mains fails, an inverter will be used to produce AC electricity at mains voltage from the DC battery.

DC to DC converters are important in portable electronic devices such as cellular phones and laptop computers, which are supplied with power from batteries primarily. Such electronic devices often contain several sub-circuits, each with its own voltage level requirement different from that supplied by the battery or an external supply (sometimes higher or lower than the supply voltage). Additionally, the battery voltage declines as its stored power is drained. Switched DC to DC converters offer a method to increase voltage from a partially lowered battery voltage thereby saving space instead of using multiple batteries to accomplish the same thing. Most DC to DC converters also regulate the output. Some exceptions include high-efficiency LED power sources, which are a kind of DC to DC converter that regulates the current through the LEDs, and simple charge pumps which double or triple the input voltage.

[edit] Conversion methods

Linear regulators can only output at lower voltages from the input. They are very inefficient when the voltage drop is large and the current is high as they dissipate heat equal to the

product of the output current and the voltage drop; consequently they are not normally used for large-drop high-current applications. The inefficiency wastes power and requires higher-rated and consequently more expensive and larger components. The heat dissipated by high-power supplies is a problem in itself and it must be removed from the circuitry to prevent unacceptable temperature rises. Linear regulators are practical if the current is low, the power dissipated being small, although it may still be a large fraction of the total power consumed. They are often used as part of a simple regulated power supply for higher currents: a transformer generates a voltage which, when rectified, is a little higher than that needed to bias the linear regulator. The linear regulator drops the excess voltage, reducing hum-generating ripple current and providing a constant output voltage independent of normal fluctuations of the unregulated input voltage from the transformer/bridge rectifier circuit and of the load current. Linear regulators are inexpensive, reliable if good heat sinks are used and much simpler than switching regulators. As part of a power supply they may require a transformer, which is larger for a given power level than that required by a switch-mode power supply. Linear regulators can provide a very low-noise output voltage, and are very suitable for powering noise-sensitive low-power analog and radio frequency circuits. A popular design approach is to use an LDO, Low Drop-out Regulator, that provides a local "point of load" DC supply to a low power circuit.
[edit] Switched-mode conversion

Electronic switch-mode DC to DC converters convert one DC voltage level to another, by storing the input energy temporarily and then releasing that energy to the output at a different voltage. The storage may be in either magnetic field storage components (inductors, transformers) or electric field storage components (capacitors). This conversion method is more power efficient (often 75% to 98%) than linear voltage regulation (which dissipates unwanted power as heat). This efficiency is beneficial to increasing the running time of battery operated devices. The efficiency has increased since the late 1980s due to the use of power FETs, which are able to switch at high frequency more efficiently than power bipolar transistors, which incur more switching losses and require a more complicated drive circuit. Another important innovation in DC-DC converters is the use of synchronous rectification replacing the flywheel diode with a power FET with low "on resistance", thereby reducing switching losses. Most DC-to-DC converters are designed to move power in only one direction, from the input to the output. However, all switching regulator topologies can be made bi-directional by replacing all diodes with independently controlled active rectification. A bi-directional converter can move power in either direction, which is useful in applications requiring regenerative braking. Drawbacks of switching converters include complexity, electronic noise (EMI / RFI) and to some extent cost, although this has come down with advances in chip design. DC-to-DC converters are now available as integrated circuits needing minimal additional components. They are also available as a complete hybrid circuit component, ready for use within an electronic assembly.

[edit] Magnetic

In these DC-to-DC converters, energy is periodically stored into and released from a magnetic field in an inductor or a transformer, typically in the range from 300 kHz to 10 MHz. By adjusting the duty cycle of the charging voltage (that is, the ratio of on/off time), the amount of power transferred can be controlled. Usually, this is applied to control the output voltage, though it could be applied to control the input current, the output current, or maintain a constant power. Transformer-based converters may provide isolation between the input and the output. In general, the term "DC-to-DC converter" refers to one of these switching converters. These circuits are the heart of a switched-mode power supply. Many topologies exist. This table shows the most common.
Forward

Flyback

Energy goes from the input, through the magnetics and to the load, simultaneously

Energy goes from the input and stored in the magnetics Later, it is released from the magnetics to the load Non-inverting: The output voltage is the same polarity as the input o Step-up (Boost) - The output voltage is higher than the input voltage o SEPIC - The output voltage can be lower or higher than the input Inverting: the output voltage is of the opposite polarity as the input o Inverting (Buck-Boost) o uk - Output current is continuous

No transformer

Step-down (Buck) - The output voltage is lower than the input voltage, and of the same polarity

Nonisolated

True Buck-Boost - The output voltage is the same polarity as the input and can be lower or higher Split-Pi (Boost-Buck) - Allows bidirectional voltage conversion with the output voltage the same polarity as the input and can be lower or higher. Cuk (Cuk) - Allows bidirectional voltage conversion with the output voltage of inverted polarity. With transformer

Half bridge - 2 transistors drive Full bridge - 4 transistor drive

Flyback - 1 or 2 transistor drive

May be

isolated

In addition, each topology may be:

Hard switched - transistors switch quickly while exposed to both full voltage and full current Resonant - an LC circuit shapes the voltage across the transistor and current through it so that the transistor switches when either the voltage or the current is zero

Magnetic DC-to-DC converters may be operated in two modes, according to the current in its main magnetic component (inductor or transformer):

Continuous - the current fluctuates but never goes down to zero Discontinuous - the current fluctuates during the cycle, going down to zero at or before the end of each cycle

A converter may be designed to operate in continuous mode at high power, and in discontinuous mode at low power. The Half bridge and Flyback topologies are similar in that energy stored in the magnetic core needs to be dissipated so that the core does not saturate. Power transmission in a flyback circuit is limited by the amount of energy that can be stored in the core, while forward circuits are usually limited by the I/V characteristics of the switches. Although MOSFET switches can tolerate simultaneous full current and voltage (although thermal stress and electromigration can shorten the MTBF), bipolar switches generally can't so require the use of a snubber (or two).
[edit] Capacitive Main article: Charge pump

Switched capacitor converters rely on alternately connecting capacitors to the input and output in differing topologies. For example, a switched-capacitor reducing converter might charge two capacitors in series and then discharge them in parallel. This would produce an output voltage of half the input voltage, but at twice the current (minus various inefficiencies). Because they operate on discrete quantities of charge, these are also sometimes referred to as charge pump converters. They are typically used in applications requiring relatively small amounts of current, as at higher current loads the increased efficiency and smaller size of switch-mode converters makes them a better choice.[citation needed] They are also used at extremely high voltages, as magnetics would break down at such voltages.
[edit] Electrochemical

A further means of DC to DC conversion in the kiloWatt to many MegaWatts range is presented by using redox flow batteries such as the vanadium redox battery, although this technique has not been applied commercially to date.

Pulse-width modulation (PWM), is a commonly used technique for controlling power to inertial electrical devices, made practical by modern electronic power switches. The average value of voltage (and current) fed to the load is controlled by turning the switch between supply and load on and off at a fast pace. The longer the switch is on compared to the off periods, the higher the power supplied to the load is. The PWM switching frequency has to be much faster than what would affect the load, which is to say the device that uses the power. Typically switchings have to be done several times a minute in an electric stove, 120 Hz in a lamp dimmer, from few kilohertz (kHz) to tens of kHz for a motor drive and well into the tens or hundreds of kHz in audio amplifiers and computer power supplies. The term duty cycle describes the proportion of 'on' time to the regular interval or 'period' of time; a low duty cycle corresponds to low power, because the power is off for most of the time. Duty cycle is expressed in percent, 100% being fully on. The main advantage of PWM is that power loss in the switching devices is very low. When a switch is off there is practically no current, and when it is on, there is almost no voltage drop across the switch. Power loss, being the product of voltage and current, is thus in both cases close to zero. PWM also works well with digital controls, which, because of their on/off nature, can easily set the needed duty cycle. PWM has also been used in certain communication systems where its duty cycle has been used to convey information over a communications channel.