Bios Section B2562
Bios Section B2562
1. BIOS setup
Critical Point
Selecting a field causes a help message about that field to be displayed on the right-hand side of the screen. Pressing the Enter key with the highlight on a selection that is not a submenu or auto selection will cause a list of all options for that item to be displayed. Pressing the Enter key again will select the highlighted choice. 4. To activate a submenu press the [Enter] key. 5. To return to a menu from a submenu, press the [Esc] key. 6. 7. 8. 9. To go to the Exit menu from any other menu, press the [Esc] key. Pressing the [F9] key resets all items in the BIOS to the default values. Pressing the [F10] key saves the current configuration and exits the BIOS Setup Utility. You will be asked to verify this selection before it is executed. Pressing the [F1] key gives you a general help screen.
Entering the Setup Utility After a Configuration Change or System Failure If there has been a change in the system configuration that does not agree with the parameter settings stored in your BIOS memory, or there is a failure in the system, the system beeps and/or displays an error message after the Power On Self Test (POST). If the failure is not too severe, it will give you the opportunity to modify the settings of the setup utility, as described in the following steps: 1. When you turn on or restart the computer there is a beep and/or the following message appears on the screen: Error message - please run SETUP program Press <F1> key to continue, <F2> to run SETUP 2. If an error message is displayed on the screen, and you want to continue with the boot process and start the operating system anyway, press the [F1] key.
CAUTION
If your notebook beeps a series of beeps that sounds like a code and the display is blank, please refer to the Troubleshooting Section. The Troubleshooting Section includes a list of error messages and their meanings.
Critical Point
If your data security settings require it, you may be asked for a password before the operating system will be opened. 3. 4. If an error message is displayed on the screen, and you want to enter the setup utility, press the F2] key. When the setup utility starts with a fault present, the system displays the following message: Warning! Error message [Continue] Press any key to enter the setup utility. The system will then display the Main Menu with current parameters values.
5.
MAIN MENU
SETTING STANDARD SYSTEM PARAMETERS
The Main Menu allows you to set or view the current system parameters. Follow the instructions for Navigating Through The Setup Utility to make any changes. The following tables show the names of the menu fields for the Main menu and its submenus, all of the options for each field, the default settings and a description of the fields function and any special information needed to help understand the fields use.
Critical Point
System Time and System Date can also be set from your operating system without using the setup utility. Use the calendar and time icon on your Windows Control panel or type time or date from the MS-DOS prompt.
Table 1: Fields, Options and Defaults for the Main Menu Menu Field System Time: Options Default Description Sets and displays the current time. Time is in a 24 hour format of hours:minutes:seconds with 2 digits for each. (HH:MM:SS). Example: 16:45:57. You may change each segment of the time separately. Move between the segments with the [Tab] key and/or [Shift] + [Tab] keys. Sets and displays the current date. Date is in a month/day/year numeric format with 2 digits each for month and day and 4 digits for year. (MM/ DD/YYYY) for example: 03/20/1998. You may change each segment of the date separately. Move between the segments with the [Tab] key and/ or [Shift] + [Tab] keys. Enables or disables floppy disk A. Displays the type of device on this ATA/ATAPI interface, if there is one. Pressing the Enter key selects the Primary Master submenu allowing additional device configuration options for this interface. The default setting differs between the US/European and the Japanese model. Selects the display language for the BIOS.
System Date:
[Disabled] Disabled 1.44/1.2 MB 3.5" [Fujitsu Selects Primary Master submenu MHM2200AT(PM)]
Language:
[English (US)]
Primary Master Submenu of the Main Menu The Primary Master submenu identifies which ATA devices are installed. Note: Actual hard drive label shown may vary. Depending on the drive type, information such as cylinders, heads and sectors may also be displayed.
Table 2: Fields, Options and Defaults for the Primary Master Submenu of the Main Menu Menu Field Type: Options Auto None Hard Disk Default [Auto] Description Selects the ATA/ATAPI device type. Select Auto to have the type automatically identified by the BIOS at POST. If None is selected, all of the following Set-up items do not appear. If Hard Disk is selected, you must specify the number of Cylinders, Heads, and Sectors for the drive. Select ATAPI Removable if a removable disk drive is installed at this connection. This item appears only when the type is identifed as Hard Disk. When Hard Disk is selected, you can change the value. This field is changed by incrementing (pressing the [Spacebar]) or by typing in the number. This item appears only when the type is identifed as Auto or Hard Disk. When Hard Disk is selected, you can change the value. This field is changed by incrementing (pressing the [Spacebar]) or by typing in the number. This item appears only when the type is identifed as Auto or Hard Disk. When Hard Disk is selected, you can change the value. This field is changed by incrementing (pressing the [Spacebar]) or by typing in the number. Displays the maximum capacity of the drive calculated from the parameters of the hard disk when Hard Disk is selected. This option cannot be changed when Auto is selected. Specify the number of sectors per block for multiple sector transfer.
Cylinders:
Heads:
Sectors:
Maximum Capacity:
Display only
Multi-Sector Transfers:
[16 Sectors]
Table 2: Fields, Options and Defaults for the Primary Master Submenu of the Main Menu Menu Field LBA Mode Control: Options Disabled Enabled Default [Enabled] Description Enables or disables logical Block Addressing in place of Cylinder, Head, Sector addressing. This option cannot be changed when Auto is selected. Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected. Multi-word DMA is automatically set to mode 1 for Fast PIO 1, Fast PIO 2, Fast PIO 3, and set to mode 2 for Fast PIO 4 / DMA. Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected.
[Fast PI0 4]
Disabled Multiword DMA 1 Multiword DMA 2 Ultra DMA 0 Ultra DMA 1 Ultra DMA 2
[Ultra DMA 2]
ADVANCED MENU
SETTING DEVICE FEATURE CONTROLS
The Advanced Menu allows you to: Enable or disable support for Plug & Play operating systems. Set the I/O addresses for the serial and parallel ports. Set the communication mode for the parallel port and infrared port. Select between the display panel and an external CRT display. Enable or disable compensation for your display. Configure PCI devices in your system. CPU features. Configure USB features. Follow the instructions for Navigating Through The Setup Utility to make any changes. The following tables show the names of the menu fields for the Advanced Menu and its submenus, all of the options for each field, the default settings and a description of the fields function and any special information needed to help understand the fields use.
Table 3: Fields, Options and Defaults for the Advanced Menu Menu Field Plug & Play O/S: Options No Yes Default [Yes] Description Select Yes if you are using a Plug & Play capable operating system. Select No if you need the BIOS to configure non-boot devices. No: allows Plug & Play operating system to change device system settings. Yes: prevents a Plug & Play operating system from changing system settings. *ACPI operating system ignores this setting. When selected, opens the Serial/ Parallel Port Configurations submenu which allows the user to modify settings for serial, infrared and parallel ports. When selected, opens the Keyboard/Mouse Features submenu, which allows setting external and internal keyboard and mouse parameters. When selected, opens the Video Features submenu, which allows setting of the display parameters, including routing of video signals to different displays. When selected, opens the Internal Device Configurations submenu, which allows enabling or disabling the Floppy Disk, IDE, and LAN Controllers. When selected, opens additional menus to configure PCI devices. Configures CPU features. Enables and disables the USB Floppy Disk Drive. When selected, opens the event logging submenu.
No Yes
[No]
Keyboard/Mouse Features
Video Features
Disabled Enabled
10
Serial/Parallel Port Configurations Submenu of the Advanced Menu The Serial/Parallel Port Configurations submenu provides the ability to set the I/O addresses and interrupt levels for the serial, infrared and parallel ports of your notebook.
CAUTION
I/O addresses, DMA channels and Interrupt levels can be entered in various ways, including via the BIOS setup utility, the control software for the I/O device, or the hardware. If any two ports or devices, serial or parallel, have the same I/O address assigned, your notebook will not function normally. Please keep a record of original settings before making any changes in the event that a restoration is required. See your hardware and software documentation as well as the setup utility to determine settings, limitations, etc.
Critical Point
To prevent IRQ and address conflicts, avoid changing the default settings.
CAUTION
The BIOS will warn you of a resource conflict by placing a yellow asterisk next to each device that is in conflict.
Critical Point
All I/O addresses in Table 5 are in hexadecimal.
11
Table 4: Fields, Options and Defaults for the Serial/Parallel Port Configurations Submenu of the Advanced Menu Menu Field Serial Port: Options Disabled Enabled Auto Default [Enabled] Description Configures the serial port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto). Allows user to set the serial port base I/O address when serial port is Enabled. Allows user to set the serial port interrupt when serial port is Enabled. Configures the infrared port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto). When the infrared port is enabled this option is available allowing the user to set the mode for the infrared port. Allows user to set the infrared port I/O address when the infrared port is Enabled. Allows user to set the infrared port interrupt when the infrared port is Enabled. Allows user to set the infrared port I/O address when the infrared port is Enabled. Allows user to set the infrared port DMA Channel when the infrared port is Enabled.
I/O Address:
Interrupt:
Infrared Port:
3F8 - 3FF 2F8 - 2FF 3E8 - 3EF 2E8 - 2EF IRQ 3 IRQ 4 IRQ 5 Disabled Enabled Auto
[3F8 - 3FF]
[IRQ 4]
[Enabled]
Mode:
IrDA FIR
[FIR]
I/O Address:
Interrupt:
I/O address:
DMA Channel:
3F8 - 3FF 2F8 - 2FF 3E8 - 3EF 2E8 - 2EF IRQ 3 IRQ 4 IRQ 5 100 - 107 108 - 10F 110 - 117 118 - 11F DMA 1 DMA 3
[2E8 - 2EF]
[IRQ 3]
[118 - 11F]
[DMA 3]
12
Table 4: Fields, Options and Defaults for the Serial/Parallel Port Configurations Submenu of the Advanced Menu Menu Field Parallel Port: Options Disabled Enabled Auto Default [Enabled] Description Configures the parallel port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto). When the parallel port is enabled this option is available allowing the user to set the mode for the parallel port. Bi-directional allows two-way transfer of information between your notebook and a connected parallel device. Output Only (Half Duplex) allows information to be transferred in only one direction, from your notebook to the printer or similar device. ECP Mode allows communication with the ECP class of parallel I/O devices. Allows user to set the parallel port base I/O address when the parallel port is Enabled. Allows user to set the parallel port interrupt when the parallel port is Enabled.
Mode:
[Bi-directional]
I/O address:
Interrupt:
[378 - 37F]
[IRQ 7]
13
Keyboard/Mouse Features Submenu of the Advanced Menu The Keyboard/Mouse Features submenu is for setting the parameters of the integrated and external mouse and keyboard.
14
Table 5: Fields, Options and Defaults for the Keyboard/Mouse Features Submenu of the Advanced Menu Menu Field Numlock: Options Auto On Off Disabled Enabled Default [Auto] Description Sets the NumLock function state when the computer completes booting. Enables and disables the ability to plug a mouse or keyboard into the PS/2 port and have it immediately recognized and active. Enables and disables the ability to use Hot key to enable or disable the Quick Point. Selects pointing device configurations. Configuration 1: Touch Panel: Enabled Quick Point: Enabled External PS/2 Mouse: Disabled Configuration 2: Touch Panel: Enabled Quick Point: Disabled External PS/2 Mouse: Enabled Configuration 3: Touch Panel: Disabled Quick Point: Enabled External PS/2 Mouse: Enabled Configuration 4: Touch Panel: Disabled Quick Point: Exclusive Enabled External PS/2 Mouse: Enabled [Fast] Initialization for the external PS/2 devices on resume is optimized to speed up. [Normal] Initialization is not optimized. * This item works for Windows(R) XP only.Try [Normal] option,when external PS/2 devices do not function after resume
Hot Plug:
[Enabled]
[Disabled]
[Configuration 1]
Initialization on Resume
Fast Normal
[Fast]
15
Video Features Submenu of the Advanced Menu The Video Features Submenu is for setting the display parameters.
Table 6: Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu Menu Field Display: Options Internal FlatPanel External Simultaneous Disabled Enabled Default [Internal FlatPanel] Description Selects where the video signal will be routed.
Compensation:
[Disabled]
Enables or disables compensation which controls spacing on the display. When enabled, displays with less than pixel resolution 1024 x 768 or 800 x 600 will still cover the entire screen.
16
Internal Device Configurations Submenu of the Advanced Menu The Internal Device Configurations submenu allows the user to configure other internal devices.
Figure 7. Internal Device Configurations Submenu Table 7: Fields, Options and Defaults for the Internal Device Configurations Submenu of the Advanced Menu Menu Field Floppy Disk Controller: IDE Controller: Options Disabled Enabled Disabled Enabled Default [Disabled] [Enabled] Description Enables or disables the Floppy Disk Drive. Enables or disables selected IDE devices.
17
PCI Configurations Submenu of the Advanced Menu The PCI Configurations submenu allows the user to reserve specific interrupts (IRQs) for legacy ISA devices, and to enable or disable built in PCI device modules.
Table 8: Fields, Options and Defaults for the PCI Configurations Submenu of the Advanced Menu Menu Field IRQ Reservation Options Default Description Reserve specific IRQs for use by legacy ISA devices.
18
IRQ Reservation Submenu of the PCI Configurations Submenu The IRQ Reservation submenu of the PCI Configurations submenu allows the user to mark various IRQs as reserved for use by legacy ISA devices. When an IRQ is reserved, the BIOS does not use it for embedded PCI or ISA devices.
Figure 9. IRQ Reservation Submenu Table 9: Fields, Options and Defaults for the IRQ Reservation Submenu of the PCI Configurations Submenu of the Advanced Menu Menu Field IRQ 3: Options Available Reserved Default [Available] Description Reserves IRQ 3. If Reserved is selected, the BIOS reserves IRQ 3 for use by legacy ISA devices and does not use it for embedded PCI or ISA devices. IRQ 3 is removed from the IRQ bitmap in the PCI IRQ routing table. Reserves IRQ 4. Reserves IRQ 5. Reserves IRQ 7. Reserves IRQ 9. Reserves IRQ 10. Reserves IRQ 11. Reserves IRQ 15.
IRQ 4: IRQ 5: IRQ 7: IRQ 9: IRQ 10: IRQ 11: IRQ 15:
Available Reserved Available Reserved Available Reserved Available Reserved Available Reserved Available Reserved Available Reserved
19
CPU Features Submenu of the Advanced Menu The CPU Features Submenu configures the system Processor.
Table 10: Fields, Options and Defaults for the CPU Features Submenu of the Advanced Menu Menu Field Intel(R) SpeedStep(TM) Technology Options Auto Max. Perf. Batt. Opt. Disabled Default [Auto] Description When Auto is selected, the CPU speed changes based upon the power source change. When Max. Perf. is selected, the CPU speed is maximized. When Batt. Opt. is selected, the CPU speed is optimized for battery operation. When Disabled is selected, the CPU speed is fixed to the battery optimized speed.
20
USB Features Submenu of the Advanced Menu The USB Features submenu configures the USB capabilities of the system.
Figure 11. USB Features Submenu Table 11: Fields, Options and Defaults for the ACPI Features Submenu of the Advanced Menu Menu Field USB Features: Options Disabled Enabled Default [Enabled] Description When enabled, Legacy Floppy Emulation is enabled and USB floppy is available without USBaware OS.
21
Event Logging Submenu of the Advanced Menu The Event Logging submenu is for setting up the logs for DMI event logging.
Table 12: Fields, Options and Defaults for the Event Logging Submenu of the Advanced Menu Menu Field Options Event Log Capacity: Event Log Validity: Disabled Enabled View Event Log: Enter Event Logging: System Boot Event: Clear All Event Logs: Mark Events as Read: Disabled Enabled Disabled Enabled No Yes Enter Default Space Available Valid [Enter] [Enabled] [Disabled] [No] [Enter] Description Display only Display only Allows you to view content of event log. Turns event logging on and off for all DMI events. Turns event logging on and off for DMI system boot events. When set to [Yes] all event logs will be cleared at next boot. Allows you to make all events currently in the event log as read.
22
SECURITY MENU
SETTING THE SECURITY FEATURES
The Security menu allows you to set up the data security features of your notebook to fit your operating needs and to view the current data security configuration. Follow the instructions for Navigating Through The Setup Utility to make any changes. The following tables show the names of the menu fields for the Security menu and its submenus, all of the options for each field, the default settings and a description of the fields function and any special information needed to help understand the fields use. The default condition is no passwords required and no write protection.
Critical Point
If you set a password, write it down and keep it in a safe place. If you forget the password you will have to contact your support representative to regain access to your secured functions and data. If you make an error when re-entering the password a [Warning] will be displayed on the screen. To try again, press the Enter key and then retype the password. Press the Esc key to abort the password setting process. Boot sector protection must be set to [Normal] to install or upgrade an operating system.
CAUTION
Entering a password incorrectly three times in a row will cause the keyboard and mouse to be locked out and the warning [System Disabled] to be displayed. If this happens, restart the computer by turning off and on the power with the power switch and use the correct password on reboot. If the Password on Resume is Enabled and the Pass-word on Boot is Disabled you will not have to type your password upon resuming the system from the Suspend or Save-to-Disk modes. Power Management Security will work only if Password on Boot is enabled.
23
Table 13: Fields, Options and Defaults for the Security Menu Menu Field Supervisor Password is: Options Default Clear Description A display-only field. Set is displayed when the system supervisor password is set and Clear when it is not. A display-only field. Set is displayed when the general user password is set, and Clear when it is not. Sets, changes or cancels the Supervisor Password. The Supervisor Password may be up to seven characters long and must include only letters or numbers (no symbols). Passwords are NOT casesensitive. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a Supervisor Password is set it must be used to access the BIOS setup utility. This field can only be accessed if the Supervisor Password is set. Sets, changes or cancels the User Password. The User Password may be up to seven characters long and must include only letters or numbers (no symbols). Passwords are NOT case-sensitive. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Reenter New Pass-word field. When a User Password is set it must be used to access the BIOS setup utility.
Clear
[Enter]
[Enter]
[0]
24
Table 13: Fields, Options and Defaults for the Security Menu Menu Field Password on Boot: Options Enabled First Boot Every Boot Default [Disabled] Description When set to Enabled, a password (User or Supervisor) is required after the Power On Self Test (POST) before the operating system will be read from a disk. When set to Disabled no password is required. If no Supervisor Password is set this feature is not available and no password is required. When Supervisor Only is selected, only the Supervisor can boot from removeable media. Only the user who enters the Supervisor Password before OS boot is treated as the Supervisor. When All is selected, booting from removeable media is not restricted. When Supervisor Only is selected, only the Supervisor can access the floppy disk. Only the user who enters the Supervisor Password before OS boot is treated as the Supervisor. When All is selected, floppy disk access is not restricted. Configures hard disk security features. Sets Owner information. Sets protection mode for hard disk drive. Allows you to enable or disable the Security Panel feature upon Resume from Suspend.
[All]
[All]
Hard Disk Security: Owner Information: Hard Disk Boot Sector: Security Panel on Resume:
[Normal] [Enabled]
Exiting from the Security Menu When you have finished setting the parameters on the Security Menu, you can either exit from setup utility or move to another menu. If you wish to exit from setup utility, press the [Esc] key to go to the Exit Menu. If you wish to move to another menu, use the cursor keys.
25
Hard Disk Security Submenu of the Security Menu The Hard Disk Security submenu is for configuring hard disk security features.
Figure 14. Hard Disk Security Submenu Table 14: Fields, Options and Defaults for the Hard Disk Security Submenu of the Security Menu Menu Field Primary Master: Options Disabled Enabled Default [Disabled] Description Disabled: No password protection. Enabled: Hard drive is locked with the password. Data in the locked disk cannot be read on any systems other than the original system on which it was locked, or on systems that have the identical password setting.
26
Owner Information Submenu of the Security Menu The Owner Information submenu is for setting owner information.
27
Table 15: Fields, Options and Defaults for the Owner Information Submenu of the Security Menu Menu Field Owner Information Is: Set Owner Information: Foreground Color: Options Default Clear [Enter] [Gray] Description Display only. Field to write owner information i.e. name.
Black Blue Green Cyan Red Magenta Brown White Gray Light Blue Light Green Light Cyan Light Red Light Magenta Yellow Bright White Background Color: Black Blue Green Cyan Red Magenta Brown White Gray Light Blue Light Green Light Cyan Light Red Light Magenta Yellow Bright White
[Black]
28
POWER MENU
SETTING POWER MANAGEMENT FEATURES
The Power menu allows you to set and change the power management parameters. Follow the instructions for Navigating Through the Setup Utility to make any changes. The following tables show the names of the menu fields for the Power menu and its submenus, all of the options for each field, the default settings and a description of the fields function and any special information needed to help understand the fields use.
Critical Point
In Windows 98 Auto-suspend Timeout, Hard Disk Timeout, and Video Timeout features are available exclusively through the operating system. When resuming from a Save-to-Disk suspension there will be a delay while the contents of system memory and operating parameters are loaded from the hard drive.
CAUTION
In Save-to-Disk mode there is no indication on the Status Indicator to let you know you are suspended rather than shut off from the power switch. You may want to make a habit of always trying the Suspend/ Resume button before using the power switch. Wake-on-Modem ring when enabled will draw power from the bridge battery alone when your system is running off battery power. This may potentially drain your bridge battery. Disabling Wake-on-Modem ring will prevent this from happening.
29
Table 16: Fields, Options and Defaults for the Power Menu Menu Field Power Savings: Options Default Disabled [Customized] Customized Maximum Power Savings Maximum Performance Off 30 seconds to 20 Minutes [Off] Description Sets the power savings parameters to a factory installed combination of parameters, a custom set of parameters set by you or no power saving features.
Display Timeout:
Off 2 to 20 Minutes
[Off]
Standby Timeout:
Off 1 to 16 Minutes
[4 Minutes]
Off 5 to 60 minutes
[15 Minutes]
Sets the length of time that the hard drive can be inactive before your notebook automatically turns off the power to the hard drive controller and drive motor. If you choose a factory installed combination of parameters this field will display the setting. If you choose to customize the parameters you will be able to set this yourself. The options available vary from Off, which has noinactivity shutoff, to 20 minutes. Sets the length of time without any user input device activity before the display is turned off. If you choose a factory combination of parameters, this field will display the setting. If you choose to customize the parameters, you will be able to set this yourself. Off has no inactivity shutoff. Sets the length of time without any user input device activity before the CPU is set to half speed and the display and the hard drive are turned off. If you choose a factory combination of parameters this field will display the setting. If you choose to customize the parameters you will be able to set this yourself. Sets the length of time without any I/O activity before your note-book goes into Suspend mode. If you choose a factory combination of parameters this field will display that setting. If you choose to customize the parameters you will be able to set this yourself. Off has no inactivity suspension.
30
Table 16: Fields, Options and Defaults for the Power Menu Menu Field Suspend Mode: Options Save to Disk Default [Suspend] Description Sets the form of suspension state. If you choose Suspend, you will suspend operation with power to system memory, and everything else powered down or in a very low power state. If you choose Save-toDisk your notebook will save all of system memory and the operating parameters to the hard drive before turning your notebook to the pseudo-off condition. When set to After 1 Hour, your notebook will automatically save all of system memory and the operating parameters to the hard drive and go to the pseudo-off if you leave your notebook in Suspend mode for more than an hour. Sets whether or not to Resume from a suspension state when a message is received by telephone line. This feature will not operate if the Saveto-Disk mode is enabled. This feature applies to internal and external modems. Sets whether or not to resume from a suspension state at a designated time. This feature is available from either the Suspend mode or the Save-to-Disk mode. Sets the designated time, on a 24hour clock, when the notebook is to automatically resume operation from the Suspend state. The format of the clock setting is hours:minutes: seconds. Each segment of the time is set separately, either by incrementing or by typing in the numbers. You move between the segments with the [Tab] key or the [Shift]+[Tab] keys. This only applies when Resume on Time is set to On. When selected, opens the Advanced Features submenu which allows setting additional power saving parameters.
[Off]
Off On
[Off]
[Off]
Resume Time:
[00:00:00]
Advanced Features:
Off
31
Factory Installed Values for Power Saving Profiles Hard Disk Timeout Customized: Maximum Power Savings: Maximum Performance: Disabled: Sample Customized Profile: (To get even better battery life keep the display and volume settings as low as possible and use the sample customized profile.) Off 30 Seconds Off Off 2 Minutes Display Timeout Off 2 Minutes Off Off 2 Minutes Standby Timeout 4 Minutes 1 Minute Off Off 1 Minute Auto Suspend Timeout 15 Minutes 5 Minutes 15 Minutes Off 5 Minutes
32
Advanced Features Submenu of the Power Menu The Advanced Features submenu is for setting some non-time related power saving parameters.
Figure 17. Advanced Features Submenu Table 17: Fields, Options and Defaults for the Advanced Features Submenu of the Power Menu Menu Field Options Suspend/Resume Disabled Switch: Enabled Default [Enabled] Description Sets the function of the Suspend/ Resume button when your notebook is in an active state. The resume function can not be disabled as it works regardless of any other settings.+ Enables and disables having closure of the Display panel put your notebook in Suspend mode. Enables and disables having opening the Display panel acting as an automatic resume. Enables and disables having activity on the serial port cause the system to reactivate from inactivity timeouts. Configures the ACPI Performance control.
Lid Closure Suspend: Lid Open Resume: Serial Mouse Activity: Performance control
[On]
[Off]
[Disabled]
[Fixed]
Exiting from Power Menu When you have finished setting the boot parameters with the Power menu, you can either exit from the setup utility or move to another menu. If you wish to exit from the setup utility press the [Esc] key to go to the Exit menu. If you wish to move to another menu, use the cursor keys.
33
BOOT MENU
SELECTING THE OPERATING SYSTEM SOURCE
The Boot Menu is used to select the order in which the BIOS searches sources for the operating system. Follow the instructions for Navigating Through the Setup Utility to make any changes. The following tables show the names of the menu fields for the Boot menu and its submenu, all of the options for each field, the default settings and a description of the fields function and any special information needed to help understand the fields use.
Figure 18. Boot Menu Table 18: Fields, Options and Defaults for the Boot Menu Menu Field QuickBoot Mode: Options Disabled Enabled Auto Disabled Enabled Default [Enabled] Description Turns on and off booting with a truncated set of Power On Self Test. (Fewer tests mean faster turn on.) Turns on and off display of test results instead of Fujitsu logo screen during Power On Self Test. This menu allows setting up the source for the operating system.
[Disabled]
34
Boot Device Priority Submenu of the Boot Menu The Boot Device Priority submenu is for setting the order of checking of sources for the operating system.
Table 19: Fields, Options and Defaults for the Boot Device Priority Submenu of the Boot Menu Menu Field Floppy Disk Drive Options Description The boot selections determine the order in which the BIOS searches for the operating system during a startup sequence. To change the order highlight one source by using the [up] or [down] cursor keys and then press the [+] or [-] key to change the order number for that source. Be sure to save your changed order when you exit the BIOS setup utility.
Exiting from Boot Menu When you have finished setting the boot parameters with the Boot menu, you can either exit from the setup utility or move to another menu. If you wish to exit from the setup utility press the [Esc] key to go to the Exit menu. If you wish to move to another menu, use the cursor keys.
35
INFO MENU
DISPLAYS BASIC SYSTEM INFORMATION
The Info menu is a display-only screen that provides the configuration information for your notebook. The following table shows the names of the menu fields for the Info menu and the information displayed in those fields. These fields are for information purposes only, and are not editable.
Figure 20. Info Menu Table 20: Fields, Options and Defaults for the Info Menu Menu Field BIOS Version: BIOS Date: BIOS Area: CPU Type: CPU Speed: L1 Cache: L2 Cache: Total Memory: Memory Slot: Options Default 1.xx 04/17/2001 E000h FFFFh Pentium (R) III processor xxx MHz 32 KB 512 KB 128 MB 128 MB SDRAM Description
36
EXIT MENU
LEAVING THE SETUP UTILITY
The Exit Menu is used to leave the setup utility. Follow the instructions for Navigating Through The Setup Utility to make any changes.
Figure 21. Exit Menu The following table shows the names of the menu fields for the Exit menu, the default settings and a description of the fields function and any special information needed to help understand the fields use.
37
Table 21: Fields, Options and Defaults for the Exit Menu Menu Field Exit Saving Changes Optional Default Description Exit Saving Changes and Exit will store all the entries on every menu of the setup utility to the BIOS memory and then exit the setup utility. A confirmation message Save Configuration changes and exit now? [Yes] [No] will be displayed. Selecting Exit Discarding Changes and Exit will exit the setup utility with out writing to the BIOS memory. When the BIOS recognizes this selection it will load the operating system and begin operation. Selecting Load Setup Defaults will load the factory preset default values for all menu fields, then display the message Load default configuration now? [Yes] [No]. When confirmed the setup utility will return to the Exit Menu. To return to another menu follow the directions in the Navigating Through The Setup Utility section. Selecting Discard Changes will load the previous values in BIOS memory for all menu fields. The message Load previous now? [Yes] [No] will be displayed. When confirmed the setup utility will return to the Exit menu. To return to another menu, follow the directions in the Navigating Through The Setup Utility section. Selecting Save Changes will cause the new settings in all menus to be written to the BIOS memory. The message Save configuration changes now? [Yes] [No] will be displayed. When confirmed, the setup utility will return to the Exit menu. To return to another menu, follow the directions in the Navigating Through The Setup Utility section.
Discard Changes
Save Changes
38
Figure 22. Typical Diagnostic Screen Normal Messages 0640K System Memory Passed nnnnM Extended Memory Passed nnnnK Memory Cache Passed System BIOS shadowed Mouse initialized Press <F2> to enter SETUP Entering SETUP ... Table 22: Normal Messages in Diagnostic Screen Error Messages System Memory Failed at offset: xxxx Failing Bits: zzzz Extended Memory Failed at offset: xxxx Failing Bits: zzzz zzzz System cache error - Cache disabled Keyboard controller error Keyboard error Diskette drive A error Failure Fixed Disk n
39
Table 23: Error Messages in Diagnostic Screen Error Messages System timer error Real time clock error System CMOS checksum bad - Default configuration used Previous boot incomplete - Default configuration used Press <F1> to resume,<F2> to Setup Check date and time settings Password locked: Fixed Disk n No Save To Disk partition or file exists on Fixed Disk - Save To Disk features is disabled. Not enough Save To Disk partition or file exists on Fixed Disk. - Save To Disk feature is disabled. Hard Disk Drive is not installed. - Save To Disk feature is disabled. Unknown Save To Disk error. - Save To Disk feature is disabled. Hard disk sector read function failed. - Save To Disk feature is disabled. Hard disk sector write function failed. - Save To Disk feature is disabled. Save To Disk partition or file corrupted. - Save To Disk feature is disabled. Fixed Disk is not installed. Cannot restore from disk. To restore from disk : turn off system, install original fixed disk and reboot. Press <F1> to continue to boot without save to disk data. Fixed Disk has been changed. Cannot restore from disk. To restore from disk : turn off system, install original fixed disk and reboot. Press <F1> to continue to boot without save to disk data.
40