Control Relays

7/0
Contents
7 - Control relays
Control relays
b k control relays v For a.c or d.c control circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7/4 v For d.c control circuit (low consumption) . . . . . . . . . . . . . . . . . . . . . . . page 7/5 v Instantaneous and time delay auxiliary contact blocks . . . . . . . . . . . . page 7/6 v Mounting and marking accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7/7 b Mini-control relays v Mini-control relays CA2 SK and CA3 SK . . . . . . . . . . . . . . . . . . . . . . page 7/12 v Mini-control relay with alternating contacts CA2 SKE . . . . . . . . . . . . page 7/12 v Instantaneous auxiliary contacts and coil suppressor modules . . . . . page 7/13 b TeSys d control relays and add-on blocks v Control circuit: a.c., d.c. or low consumption, . . . . . . . . . . . . . . . . . . page 7/21 v Add-on blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7/22 v Accessories and spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7/23
Zelio Time: timing relays

Selection guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7/26
Zelio Control: measurement and control relays

Selection guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7/28
7/1
Characteristics
Control relays
k control relays
Environment
Conforming to standards Product certifications Operating positions IEC 60947, NF C 63-140, VDE 0660, BS 5424 UL, CSA
Vertical axis
Horizontal axis
Without derating
Without derating
Connection Screw clamp connections Solid cable Flexible cable without cable end Flexible cable with cable end Solid cable Spring terminals Flexible cable without cable end Faston connectors Clip Solder pins for With locating device between printed circuit board power and control circuits Tightening torque Philips head n 2 and 6 Terminal referencing Conforming to standards EN 50005 and EN 50011 Protective treatment Conf. to IEC 60068 (DIN 50016) Degree of protection Conforming to VDE 0106 Ambient air temperature around the device Maximum operating altitude Vibration resistance 5...300 Hz Flame resistance Storage Operation Without derating Control relay open Control relay closed Conforming to UL 94 Conforming to NF F 16-101 and 16-102 Control relay open Control relay closed Conforming to VDE 0106 and IEC 60536
mm2 mm2 mm2 mm2 mm2 mm
Min. 1 x 1.5 1 x 0.75 1 x 0.34 1 x 0.75 1 x 0.75 2 x 2.8 or 1 x 6.35 4 mm x 35 microns 0.81.3 Up to 8 contacts
Max. 2x4 2x4 1 x 1.5 + 1 x 2.5 1 x 1.5 1 x 1.5
Possible positions for CA2 K only, with derating, please consult your Regional Sales Office. Max. to IEC 60947 1 x 4 + 1 x 2.5 2 x 2.5 1 x 1.5 + 1 x 2.5 2 x 1.5 2 x 1.5
N.m
C C m
"TC (Klimafest, Climateproof) Protection against direct finger contact (devices with screw clamp terminals or pins for printed circuit board) - 50...+ 80 - 25...+ 50 2000 2 gn 4 gn Self-extinguishing material V1 Conforming to requirement 2 10 gn 15 gn SELV (Safety Extra Low Voltage), up to 400 V
Shock resistance (1/2 sine wave, 11 ms) Safety separation of circuits
Control circuit characteristics
Control relay type Rated control circuit voltage (Uc) Control voltage limits For operation (y 50 C) single voltage coil For drop-out Mechanical durability at Uc 50/60 Hz coil In millions of operating cycles Standard c coil Wide range, low consumption c coil Maximum operating rate In operating cycles per hour Average consumption Inrush at 20 C and at Uc Sealed Heat dissipation Operating time Between coil energisation and at 20 C and at Uc opening of the N/C contacts closing of the N/O contacts
CA2 K a 12...690 0.8...1.15 Uc y 0.2 Uc 10 10 000 30 VA 4.5 VA 1.3 5...15 10...20 10...20 15...25 2
CA3 K c 12...250 0.8...1.15 Uc y 0.1 Uc 20 10 000 3W 3W 3 25...35 30...40 10 15 2
CA4 K c 12...120 0.7...1.3 Uc y 0.1 Uc 30 6000 1.8 W 1.8 W 1.8 25...35 30...40 10...20 15...25 2
W ms ms
Between coil de-energisation and opening of the N/O contacts ms ms closing of the N/C contacts ms Maximum immunity to microbreaks
References : pages 7/4 and 7/5
Dimensions : page 7/8
Schemes : page 7/9
7/2
Characteristics (continued)
Control relays
k control relays
Contact characteristics of control relays and instantaneous contact blocks

Number of auxiliary contacts On CAp K On LA1 K Rated operational voltage (Ue) Up to Rated insulation voltage (Ui) Conforming to BS 5424 Conforming to IEC 60947 Conforming to VDE 0110 group C Conforming to CSA C 22-2 n 14 Conventional thermal current For ambient temperature y 50 C (Ith) Frequency of the operational current Minimum switching capacity U min (DIN 19 240) I min Short-circuit protection Conforming to IEC 60947 and VDE 0660, gG fuse Rated making capacity Conforming to IEC 60947 I rms Short-time rating Permissible for 1s 500 ms 100 ms Insulation resistance Non-overlap distance CAp K and LA1 K: linked contacts conforming to INRS, BIA and CNA specifications V V V V V A Hz V mA A 4 2 or 4 for CA2 K and CA3 K, 2 for CA4 K 690 690 690 750 600 10 Up to 400 17 5 10
A A A A M mm
110 80 90 110 > 10 0.5 (see schemes page 7/9)
Operational power of contacts conforming to IEC 60947

a.c. supply, category AC-15 d.c. supply, category DC-13
Electrical durability (valid for up to 3600 operating cycles/hour) on an inductive load such as the coil of an electromagnet: making current (cos 0.7) = 10 times the power broken (cos 0.4)
Electrical durability (valid for up to 1200 operating cycles/hour) on an inductive load such as the coil of an electromagnet, without economy resistor, the time constant increasing with the load.
V W W W W 24 120 55 15 720 48 80 38 11 600 110 60 30 9 400 220 440 600 52 28 8 300 51 26 7 230 50 25 6 200
V 1 million operating cycles 3 million operating cycles 10 million operating cycles Occasional making capacity VA VA VA VA
24
110/ 127 48 96 240 17 34 86 7 14 36 1000 2050 5000
48
220/ 380/ 440 600/ 230 400 690 440 800 880 1200 158 288 317 500 66 120 132 200 10 000 14 000 13 000 9000
Time constant in ms
1 Breaking limit of contacts valid for: b maximum of 50 operating cycles at 10 s intervals (power broken = making current x cos 0.7). 2 b b b Electrical durability of contacts for: 1 million operating cycles (2a) 3 million operating cycles (2b) 10 million operating cycles (2c).
Power broken in VA
Power broken in W
16 000 10 000 8000 6000 5000 4000 3000 2000 1000 800 600 500 400 300 200 1000 700 500 300 200 100 80 60 50 40 30 20 10 8 6 12 24 48 110 220 440 600 V
4 3
250
200 140
3 Breaking limit of contacts valid for: b maximum of 20 operating cycles at 10 s intervals with current passing for 0.5 s per operating cycle. 4 Thermal limit
2a 2b 2c
2a 2b
24 48
100
100 80 60 40
50
2c
20 110 120 220 380 500 440 690 V
References : page 7/6
Schemes : page 7/9
7/3
References
Control relays
k control relays
For a.c. or d.c. control circuit
Control relays for a.c. control circuit

816892
b Mounting on 35 mm 7 rail or 4 screw fixing. b Screws in the open "ready-to-tighten" position.

Control circuit Consumption Auxiliary contacts Basic reference, to be completed by adding the voltage code (1) Weight
kg
Screw clamp connections

CA2 KN40pp 4.5 VA 4 3 2 1 2 CA2 KN40pp CA2 KN31pp CA2 KN22pp 0.180 0.180 0.180
816891
Spring terminal connections

4.5 VA 4 3 2 1 2 CA2 KN403pp CA2 KN313pp CA2 KN223pp 0.180 0.180 0.180
Faston connectors, 1 x 6.35 or 2 x 2.8

4.5 VA CA2 KN403pp 4 3 2 1 2 CA2 KN407pp CA2 KN317pp CA2 KN227pp 0.180 0.180 0.180
Solder pins for printed circuit boards

4.5 VA 4 3 2 1 2 CA2 KN405pp CA2 KN315pp CA2 KN225pp 0.210 0.210 0.210
Control relays for d.c. control circuit

819411

3W 4 3 2 1 2 CA3 KN40pp CA3 KN31pp CA3 KN22pp 0.225 0.225 0.225

3W CA3 KN407pp 4 3 2 1 2 CA3 KN403pp CA3 KN313pp CA3 KN223pp 0.225 0.225 0.225


(1) Standard control circuit voltages (for other voltages, please consult your Regional Sales Office): Control relays CA2 K (0.8...1.15 Uc) (0.85...1.1 Uc) Volts a 12 20 24(2) 36 42 48 110 115 127 220/ 230 230/ 380/ 400 400/ 440 500 660/ 50/60 Hz 230 240 400 415 690 Code J7 Z7 B7 C7 D7 E7 F7 FE7 FC7 M7 P7 U7 Q7 V7 N7 R7 S7 Y7 Up to and including 240 V, coil with integral suppression device available: add 2 to the code required. Example: J72 Control relays CA3 K (0.8...1.15 Uc) Volts c 12 20 24(2) 36 48 60 72 100 110 125 200 220 230 240 250 Code JD ZD BD CD ED ND SD KD FD GD LD MD MPD MUD UD Coil with integral suppression device available: add 3 to the code required. Example: JD3. (2) When connecting an electronic sensor or timer in series with the coil of the control relay, select a 20 V coil (a code Z7, c code ZD) so as to compensate for the incurred voltage drop.
Characteristics : pages 7/2 and 7/3
Schemes : page 7/9
7/4
References
Control relays
k control relays
For d.c. control circuit
Low consumption control relays (d.c. control circuit)

816895
Control circuit Consumption
Auxiliary contacts
Basic reference, to be completed by adding the voltage code (1)
Weight
kg

1.8 W CA4 KN40ppp 4 3 2 1 2 CA4 KN40pp CA4 KN31pp CA4 KN22pp 0.235 0.235 0.235

1.8 W 4 3 2 1 2 CA4 KN403pp CA4 KN313pp CA4 KN223pp 0.235 0.235 0.235


(1) Standard control circuit voltages (for other voltages, please consult your Regional Sales Office): Control relays CA4 K (Wide range coil: 0.7...1.3 Uc) Volts c 12 20 24 48 72 110 120 Code JW3 ZW3 BW3 EW3 SW3 FW3 GW3
Schemes : page 7/9
7/5
References
Control relays
k control relays
Instantaneous and time delay auxiliary contact blocks
Instantaneous auxiliary contact blocks

816899
Clip-on front mounting, 1 per control relay

Connection Composition Reference Weight
LA1 KN20
Screw clamp terminals
2 1 4 3 2 1 2 1 4 3 2 1 2 1 4 3 2 1
2 1 1 2 3 4 2 1 1 2 3 4 2 1 1 2 3 4
LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1 LA1
KN20 KN02 KN11 KN40 (1) KN31 (1) KN22 (1) KN13 (1) KN04 (1) KN203 KN023 KN113 KN403 (1) KN313 (1) KN223 (1) KN133 (1) KN043 (1) KN207 KN027 KN117 KN407 (1) KN317 (1) KN227 (1) KN137 (1) KN047 (1)
kg 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045
816900
Spring terminals
LA1 KN40
Faston connectors 1 x 6.35 or 2 x 2.8
Electronic time delay contact blocks

b b b b b
816899
Relay output with common point changeover contact, a or c 240 V, 2 A maximum Control voltage 0.85...1.1 Uc Maximum switching capacity 250 VA or 150 W Operating temperature - 10...+ 60 C Reset time: 1.5 s during the time delay period 0.5 s after the time delay period
Clip-on front mounting, 1 per control relay

Voltage Type Timing range Composition Reference Weight
7
LA2 KT2p V a or c 24...48 On-delay
s 1...30
LA2 KT2E
kg 0.040
a 110...240
On-delay
1...30
LA2 KT2U
0.040
Other versions
Electronic timers type RE4. Please consult your Regional Sales Office.
(1) Block of 4 contacts for use on CA2 K and CA3 K.
Characteristics : page 7/3
Schemes : page 7/9
7/6
References
Control relays
k control relays
Mounting and marking accessories
Suppressor modules incorporating LED indicator

Mounting and connection Clips onto front of relay with locating device. No tools required. Type For voltages a and c 12...24 V a and c 32...48 V a and c 50...129 V LA4 K ppp a and c 130...250 V Diode + Zener diode (2) c 12...24 V c 32...48 V RC (3) a 220...250 V Sold in lots of 5 Unit reference LA4 KE1B Weight kg 0.010
Varistor (1)
LA4 KE1E
0.010
LA4 KE1FC
0.010
LA4 KE1UG
0.010
LA4 KC1B
0.010
LA4 KC1E
0.010
LA4 KA1U
0.010
Mounting accessories
Description Application Sold in lots of Clip-on 1 Unit reference LA9 D973 Weight kg 0.025
Mounting plates
On 1 4 rail
On 2 4 rails
110/120 mm fixing centres
10
DX1 AP25
0.065
LA9 D973
Marking accessories
Description Application Sold in lots of 100 Unit reference LA9 D90 Weight kg 0.001
Marker holder
Clip-on fixing on front face
Clip-in markers
4 maximum per relay
Strips of 10 identical numbers 0 to 9 Strips of 10 identical capital letters A to Z
25
AB1 Rp (4)
0.002
25
AB1 Gp (4)
0.002
(1) Protection provided by limiting the transient voltage to 2 Uc max. Maximum reduction of transient voltage peaks. Slight increase in drop-out time (1.1 to 1.5 times the normal time). (2) No overvoltage or oscillating frequency. Polarised component. Slight increase in drop-out time (1.1 to 1.5 times the normal time). (3) Protection by limiting the transient voltage to 3 Uc max. and limitation of the oscillating frequency. Slight increase in drop-out time (1.2 to 2 times the normal time). (4) Complete the reference by replacing the dot with the required character.
7/7
Dimensions, mounting
Control relays
7
k control relays
Control relays
CA2 K, CA3 K, CA4 K
On panel On printed circuit board
LA1 K
=
8,65
= = =
A1
58
58
50
45
50
35
57
35 45
A2
On mounting rail AM1 DP200 or AM1 DE200 (7 35 mm)
58
57
45
LA9 D973
On asymmetrical rail with clip-on mounting plates
DX1 AP25
On asymmetrical rail with clip-on mounting plates
DZ5 ME5
50
53
120
57
21
35 45
57
57
27
45
Electronic time delay contact blocks
LA2 KT
On control relay
LA2 KT 27
38
38
38
57
Suppressor modules
LA4 K
On control relay
25
LA4 K
22
57
Characteristics: pages 7/2 and 7/3
References: pages 7/4 to 7/7
Schemes: page 7/9
7/8
58
22
58
110
Schemes
Control relays
k control relays
Control relays
CA2 K, CA3 K, CA4 K
4 N/O
13/NO 23/NO 33/NO 43/NO
With integral suppression device

CA3 K
3 N/O + 1 N/C
13/NO 33/NO 43/NO 21/NC
CA4 K
2 N/O + 2 N/C
13/NO 43/NO 21/NC 31/NC
A1
A2
A1
A2
A2
14
24
34
44
A1
14
22
32
14
22
34
44
44
A2
+A1
+ A1
_ A2
Instantaneous auxiliary contact blocks LA1 K

For CA2 K, CA3 K, CA4 K
2 N/O LA1 KN20, LA1 KN207
53/NO 63/NO
For CA2 K, CA3 K

1 N/O + 1 N/C LA1 KN11, LA1 KN117
53/NO 61/NC
2 N/C LA1 KN02, LA1 KN027

51/NC 61/NC
4 N/O LA1 KN40, LA1 KN407

53/NO 63/NO 73/NO 83/NO
3 N/O + 1 N/C LA1 KN31, LA1 KN317

53/NO 73/NO 83/NO 61/NC
2 N/O + 2 N/C LA1 KN22, LA1 KN227

53/NO 83/NO 84 61/NC 62 71/NC 72
52
62
62
54
64
54
64
54
74
84
54
62
74
84
1 N/O + 3 N/C LA1 KN13, LA1 KN137

53/NO 61/NC 71/NC 81/NC
4 N/C LA1 KN04, LA1 KN047

51/NC 61/NC 71/NC 81/NC
52
62
72
54
62
72
Electronic time delay contact blocks LA2 KT

For CA2 K, CA3 K, CA4 K
1 C/O LA2 KT2
A1
16 18
Suppressor modules
LA4 KC LA4 KE
A2
15
82
82
54
References: pages 7/4 to 7/7
Dimensions, mounting: page 7/8
7/9
Characteristics
Control relays
Mini-control relays types CAp SK and CA2 SKE
Environment
Rated insulation voltage (Ui) Conforming to IEC 60947, VDE 0110 gr C, BS 5424, CSA 22-2 n 14, UL 508 Conforming to standards Product certifications Protective treatment Conforming to IEC 60068 (DIN 50015) Degree of protection Conforming to VDE 0106 Ambient air temperature Storage around the device Operation Maximum operating altitude Without derating Operating position V 690
IEC 60947, NF C 63-110, VDE 0660, BS 5424 UL, CSA TC (Klimafest, Climateproof) Protection against direct finger contact - 50+ 70 - 20+ 50 2000 Horizontal axis
C C m
Vertical axis
Without derating Connection by connectors Solid cable Flexible cable without cable end Flexible cable with cable end Pozidriv n 1 head Conforming to standards EN 50005 and EN 50011 mm2 mm2 mm2 N.m Min. 1 x 1.5 or 2 x 1.5 1 x 0.5 or 2 x 0.35 1 x 0.35 or 2 x 0.35 0.8 Up to 4 contacts
Without derating Max. 1 x 6 or 2 x 4 1 x 6 or 2 x 2.5 1 x 6 or 2 x 1.5
Tightening torque Terminal referencing

Control relay type Rated control circuit voltage (Uc) Control voltage limits For operation (y 50 C) For drop-out Average consumption Inrush at 20 C and at Uc Sealed Heat dissipation Operating time Between coil energisation and at 20 C and at Uc opening of the N/C contacts closing of the N/O contacts Between coil de-energisation and opening of the N/O contacts closing of the N/C contacts Maximum operating rate In operating cycles per hour Mechanical durability at Uc 50/60 Hz coil in millions of operating cycles Standard c coil V CA2 SK a 24400 0.851.1 Uc u 0.20 Uc 16 VA 4.2 VA 1.4 816 714 68 810 1200 10 CA2 SKE CA3 SK c 1272 0.851.1 Uc u 0.10 Uc 2.2 W 2.2 W 2.2 1018 812 46 68 1200 10
W ms ms ms ms
23 VA 4.9 VA 1.5
Schemes : page 7/15
7/10
Control relays
Auxiliary contact characteristics of mini-control relays and instantaneous contact blocks

Rated operational voltage (Ue) Rated insulation voltage (Ui) V V Up to 690 690 Conforming to IEC 96047, BS 5424, VDE 0110 group C, CSA C 22-2 n 14 Conventional rated For ambient temperature thermal current (Ith) y 55 C Frequency of the operational current Short-circuit protection Conforming to IEC 60947 and VDE 0660, gl fuse
A Hz A
10 Up to 400 10
Operational power of contacts conforming to IEC 60947

a.c. supply, category AC-15 Electrical durability (valid for up to 3600 operating cycles/hour) on an inductive load such as the coil of an electromagnet: making current (cos 0.7) = 10 times the power broken (cos 0.4). V 1 million operating cycles 3 million operating cycles 10 million operating cycles Occasional making capacity VA VA VA VA 110/ 127 48 96 240 17 34 86 7 14 36 1000 2050 5000 24 48 220/ 230 440 158 66 10000 380/ 400 800 288 120 14000 440 880 317 132 13 000 d.c. supply, category DC-13 Electrical durability (valid for up to 1200 operating cycles/hour) on an inductive load such as the coil of an electromagnet, without economy resistor, the time constant increasing with the load. V W W W W 24 120 55 15 720 48 80 38 11 600 110 60 30 9 400 220 52 28 8 300 440 51 26 7 230
Schemes : page 7/15
7/11
References
Control relays
Mini-control relays types CA2 SK and CA3 SK
Mini-control relay type CA2 SKE with alternating contacts
Mini-control relays
b Width of mini-control relays 27 mm. b Mounting on 35 mm 7 rail. b Connection by connectors.
Control circuit supply Auxiliary contacts Basic reference, to be completed by adding the voltage code (1) CA2 SK20pp CA2 SK11pp CA3 SK20pp CA3 SK11pp Weight
533664
CA2 SK20pp
a.c. supply
2 1
1 1
kg 0.132 0.132 0.132 0.132
d.c. supply
2 1
Mini-control relay with alternating contacts

This mini-control relay with alternating contacts (see function diagram page 7/15) makes it possible to automatically split the operating time between 2 circuits of a redundant system. By regularly energising the "safety circuits", this device makes it possible to ensure that they are operating correctly. b b b b b
CA2 SKE20pp
533665
Width of mini-control relay 45 mm. Fixing by 4 screws. Connection by connectors. Cannot be fitted with front-mounted auxiliary contact block. Cannot be fitted with coil suppressor module.
Auxiliary contacts Basic reference, to be completed by adding the voltage code (1) CA2 SKE20pp Weight
Control circuit supply
a.c. supply
kg 0.175
(1) Standard control circuit voltages (for other voltages, please consult your Regional Sales Office): Mini-control relays CA2 SK and CA2 SKE Volts a 24 48 110 120 220 230 240 50/60 Hz Code B7 E7 F7 G7 M7 P7 U7 Mini-control relays CA3 SK Volts c 12 24 36 48 72 Code JD BD CD ED SD
380 Q7
400 V7
Dimensions: page 7/14
Schemes: page 7/15
7/12
References
Control relays
Mini-control relays types CA2 SK and CA3 SK
Instantaneous auxiliary contacts and coil suppressor modules

533666
Clip-on front mounting

For use on control relays Maximum number of blocks per contactor Composition Reference Weight
CA2 SK20 LA1 SK11
2 1
2 1
LA1 SK20 LA1 SK02 LA1 SK11
kg 0.022 0.022 0.022
Suppressor modules
533667
Connection without need for tools by clipping onto right-hand side of contactor
For use on control relays CA2 SK and CA3 SK LA4 SKp1p Type For voltages a and c 24 V48 V Sold in lots of 10 Unit reference LA4 SKE1E LA4 SKE1U LA4 SKC1U Weight kg 0.003 0.003 0.003
Varistor (1)
a and c 110 V250 V 10 Diode (2) c 24 V250 V 10
(1) Protection provided by limiting the transient voltage to 2 Uc max. Maximum reduction of transient voltage peaks. Slight increase in drop-out time (1.1 to 1.5 times the normal time). (2) No overvoltage or oscillating frequency. Slight increase in drop-out time (1.1 to 1.5 times the normal time).
Dimensions: page 7/14
Schemes: page 7/15
7/13
Control relays
Dimensions
Mini-control relays
CA2 SK and CA3 SK
55,5
27
84,5 55,5 27
56
LA4 SK
3,5 LA1 SK (1) 3,5
(1) Only on CA2 SK20.
Mounting
Mini-control relays
CA2 SK and CA3 SK On mounting rail AM1 DP200 or AM1 DE200 (7 35 mm)
55,5
27
Dimensions
CA2 SKE
68 45
56
7
4
Mounting
CA2 SKE
On panel On mounting rail AM1 DP200 or AM1 DE200 (7 35 mm)
58
68
45
48-50
34-35
Schemes : page 7/15
7/14
58
56
Schemes
Control relays
Schemes
CA2 SK20, CA3 SK20
2 N/O
13/NO 23/NO
CA2 SK11, CA3 SK11

1 N/O + 1 N/C
13/NO 14 A2 14 24 21/NO 22
Energised De-energised Close Open Close Open
A1
A2
14
24
CA2 SKE
2 N/O
13/NO 23/NO
A1
A2
A1
14
24
Instantaneous auxiliary contacts

2 N/O LA1 SK20
33/NO 43/NO
2 N/C LA1 SK02

31/NC 41/NC
A2 13 23
A1
CA2 SKE
Function diagram
1 N/O + 1 N/C LA1 SK11

33/NO 34 41/NC 42
34
44
32
42
Dimensions, mounting : page 7/14
7/15
Characteristics
TeSys control relays

TeSys d control relays
Control relay type
CAD a
CAD c
CAD low consumption 690
Environment
Rated insulation voltage (Ui) Conforming to IEC 60947-5-1 Overvoltage category III and degree of pollution 3 Conforming to UL, CSA Conforming to IEC 60947 Conforming to IEC 60536 and VDE 0106 V 690 690
V kV
600 6
600 6
600 6
Rated impulse withstand voltage (Uimp) Separation of electrical circuits Conforming to standards Product certifications Protective treatment Degree of protection Ambient air temperature around the device
Reinforced insulation up to 400 V IEC 60947-5-1, N-F C 63-140, VDE 0660, BS 4794, EN 60947-5 UL, CSA
Conforming to IEC 60068 Conforming to VDE 0106 Storage Operation, conforming to IEC 60255 (0.81.1 UC) For operation at Uc Without derating Without derating in the following positions C C C m
TH Front face protected against direct finger contact IP 2X - 60+ 80 - 5+ 60 - 40+ 70 3000 - 60+ 80 - 5+ 60 - 40+ 70 3000 Protection against direct finger contact - 60+ 80 - 5+ 60 - 40+ 70 3000
Maximum operating altitude Operating positions
30
180
30
90
90
180
1 80
Shock resistance (1) half sine wave for 11ms Vibration resistance (1) 5300 Hz Screw clamp connections
Control relay open Control relay closed Control relay open Control relay closed Flexible 1 conductor 2 without cable end Flexible 1 conductor with 2 cable end Solid conductor 1 without cable 2 end Tightening torque conductor conductors mm2 mm2 mm2 mm2 mm2 mm2 N.m
10 gn 15 gn 2 gn 4 gn 14 14
10 gn 15 gn 2 gn 4 gn 14 14
10 gn 15 gn 2 gn 4 gn 14 14
conductor conductors conductor conductors
14 12.5 14 14 1.7
14 12.5 14 14 1.7
14 12.5 14 14 1.7
1 or 2 flexible or rigid conductors mm2 12.5 12.5 12.5 without cable end (1) In the least favourable direction, without change of contact state, with coil supplied at Uc.
References : pages 7/21 to 7/23
Schemes : page 7/25
7/16

Control relay type
CAD a
CAD c
CAD low consumption c 572 0.71.25 Uc 0.10.25 Uc Inrush or sealed: 2.4 45

Rated control circuit voltage (Uc) Control voltage limits Operation With coil 50/60 Hz With standard coil, wide range Drop-out Average consumption at 20 C and at Uc a 50/60 Hz (at 50 Hz) VA V 12690 0.81.1 Uc at 50 Hz 0.851.1 Uc at 60 Hz 0.30.6 Uc Inrush: 70 sealed: 8 419 12440 0.71.25 Uc 0.10.25 Uc Inrush or sealed: 5.4 3545
With standard coil Operating time (at rated control circuit voltage and at 20 C)
Between coil energisation ms and - opening of the N/C contacts - closing of the N/O contacts ms Between coil de-energisation ms and - opening of the N/O contacts - closing of the N/C contacts ms
1222 412
5055 614
6070 1015
617 2 3 30
20 2 3 30 28
25 2 3 30 40
Short supply failure Maximum operating rate Mechanical durability In millions of operating cycles
Time constant L/R
Maximum duration without ms affecting hold-in of the device In operating cycles per second With coil 50/60 Hz (at 50 Hz) With standard coil c wide range ms
Schemes : page 7/25
7/17

Characteristics of instantaneous contacts incorporated in the control relay

Number of contacts Up to Rated operational voltage (Ue) Rated insulation voltage (Ui) Conforming to IEC 60947-5-1 Conforming to UL, CSA Conventional For ambient temperature 60 C thermal current (Ith) Frequency of the operational current Minimum switching capacity U min I min Short-circuit protection Rated making capacity Short-time rating Conforming to IEC 60947-5-1 Conforming to I rms IEC 60947-5-1 Permissible for 1s 500 ms 100 ms V V V A Hz V mA 5 690 690 600 10 25...400 17 5 gG fuse: 10 A a : 140, c : 250 A A A M Guaranteed between N/C and N/O contacts Philips head n 2 and 6 ms N.m 100 120 140 > 10 1.5 (on energisation and on de-energisation) 1.2 Linked contacts in association with auxiliary contacts LAD N The 3 N/O contacts and the 2 N/C contacts of CAD N32 are linked mechanically by one mobile contact carrier.
Insulation resistance Non-overlap time Tightening torque Non-overlap distance Linked contacts
Conforming to draft standard IEC 60947-4-5
Schemes : page 7/25
7/18

Rated operational power of contacts (conforming to IEC 60947-5-1)

a.c. supply, categories AC-14 and AC-15 Electrical durability (valid for up to 3600 operating cycles/hour) on an inductive load such as the coil of an electromagnet: making current (cos 0.7) = 10 times the power broken (cos 0.4).
V VA VA VA 24 60 16 4 48 120 32 8 115 280 80 20 230 560 160 40 400 960 280 70 440 1050 300 80 600 1440 420 100
1 million operating cycles 3 million operating cycles 10 million operating cycles

Millions of operating cycles
1 8 7 6 5 4 3 2
1 0,8 0,7 0,6 0,5 0,4 0,3 0,2
0,1 0,1 0,2 0,3 0,4 0,5 0,6 0,8 1 0,7 0,9 2 3 6 8 10 5 7 9 Current broken in A 4
d.c. supply, category DC-13 Electrical durability (valid for up to 1200 operating cycles/hour) on an inductive load such as the coil of an electromagnet, without economy resistor, the time constant increasing with the power.
V W W W 24 120 70 25 48 90 50 18 125 75 38 14 250 68 33 12 440 61 28 10
1 million operating cycles 3 million operating cycles 10 million operating cycles

Millions of operating cycles
1 8 7 6 5 4 3 2 250 V
24 V 48 V 125 V
1 0,8 0,7 0,6 0,5 0,4 0,3 0,2
440 V
0,1 0,1 0,2 0,3 0,4 0,5 0,6 0,8 1 0,7 0,9 2 3 4 6 8 10 5 7 9 Current broken in A
Schemes : page 7/25
7/19
References

TeSys d control relays and add-on blocks
See page opposite for mounting possibilities according to control relay type and rating
7/20
References

Control circuit: a.c., d.c. or low consumption
Control relays for connection by screw clamp terminals

Type Number of contacts Composition Basic reference, to be completed by adding the control voltage code (1) Standard voltages a Instantaneous 5 5 3 CAD 50 pp 2 CAD 50pp (3) CAD 32pp (3) B7 B7 P7 P7 c BD BD LC (2) BL BL kg 0.580 0.580 Weight
Control relays for connection by spring terminals

Instantaneous 5 5 3 2 CAD 503pp CAD 323pp B7 B7 P7 P7 BD BD BL BL 0.580 0.580
Instantaneous auxiliary contact blocks for connection by screw clamp terminals

For use in normal operating environments
Number of contacts Maximum number per relay Clip-on mounting front side 1 1 1 1 1 on LH side 1 on LH side 1 on LH side Composition Reference Weight
CAD 32 pp
kg 2 1 1 2 2 2 1 4 3 2 1 1 2 2 2 3 4 1 2 LAD LAD LAD LAD LAD LAD LAD LAD LAD LAD LAD LAD N11 8N11 (6) N20 8N20 (6) N02 8N02 (6) N22 N13 N40 N04 N31 C22 0.030 0.030 0.030 0.030 0.030 0.030 0.050 0.050 0.050 0.050 0.050 0.050
4 (4)
4 (4) 1 Including 1 N/O and 1 N/C make before break. CAD 503pp Number of contacts Maximum number per relay Front mounting 1 Composition
With dust and damp protected contacts, for use in particularly harsh industrial environments
Reference Weight
4 (4)
protected (5) 2 2 2 2 2 2
kg 2 1 1 LA1 DX20 LA1 DX02 LA1 DY20 LA1 DZ40 LA1 DZ31 0.040 0.040 0.040 0.050 0.050
CAD 323 pp
Instantaneous auxiliary contact blocks for connection by spring terminals

This type of connection is not possible for contact blocks LAD 8 and blocks with dust and damp protected contacts. For all other instantaneous auxiliary contact blocks, add the digit 3 to the end of the references selected above. Example: LAD N11 becomes LAD N113. (1) Standard control circuit voltages (for other voltages, please consult your Regional Sales Office). a.c. supply Volts a 24 42 48 110 115 220 230 240 380 400 415 440 50/60 Hz B7 D7 E7 F7 FE7 M7 P7 U7 Q7 V7 N7 R7 d.c. supply (coils with integral suppression device fitted as standard) Volts c 12 24 36 48 60 72 110 125 220 250 440 U from 0.7 to 1.25 Uc JD BD CD ED ND SD FD GD MD UD RD Low consumption (coils with integral suppression device fitted as standard) Volts c 5 12 20 24 48 110 220 250 Code AL JL ZL BL EL FL ML UL (2) LC: low consumption. (3) To order control relays with connection by lugs, add the digit 6 to the end of the selected reference. Example: CAD50pp becomes CAD506 pp. (4) Blocks with 4 auxiliary contacts cannot be used on low consumption control relays. (5) Product fitted with 4 earth screen continuity terminals. (6) These contact blocks cannot be used on low consumption control relays. Characteristics : pages 7/16 and 7/17 Dimensions : page 7/24 Schemes : page 7/25
7/21
References

Add-on blocks
Time delay auxiliary contact blocks for connection by screw clamp terminals (1)
Number and type of contacts 1 N/C and 1 N/O Maximum number per relay Front mounting 1 Time delay Type On-delay Range 0.13 s (2) 0.130 s 10180 s 130 s (3) 0.13 s (2) 0.130 s 10180 s Reference Weight kg LAD LAD LAD LAD LAD LAD LAD T0 T2 T4 S2 R0 R2 R4 0.060 0.060 0.060 0.060 0.060 0.060 0.060
Off-delay (Sealing cover: see page 5/73) LAD T
Time delay auxiliary contact blocks for connection by spring terminals

Add the digit 3 to the references selected above. Example: LAD T0 becomes LAD T03.
Mechanical latch blocks (4)

Unlatching control Manual or electric Maximum number per relay Front mounting 1 Basic reference to be completed (5) LAD 6K10p Weight kg 0.070
Suppressor modules
These modules clip onto the top of the control relay and the electrical connection is instantly made. Fitting of an input module is still possible. LAD 6K10
RC circuits (Resistor-Capacitor)
b Effective protection for circuits highly sensitive to "high frequency" interference. b Voltage limited to 3 Uc maximum and oscillating frequency limited to 400Hz maximum. b Slight time delay on drop-out (1.2 to 2 times the normal time). For Operational Reference mounting on voltage CAD a a 2448 V LAD 4RCE a 110240 V LAD 4RCU
Weight kg 0.012 0.012
Varistors (peak limiting)

b Protection provided by limiting the transient voltage value to 2Uc maximum. b Maximum reduction of transient voltage peaks. b Slight time delay on drop-out (1.1 to 1.5 times the normal time). CAD a a 2448 V LAD 4VE a 50127 V LAD 4VG a 110250 V LAD 4VU
0.012 0.012 0.012
Freewheel diode
LAD 4pp b No overvoltage or oscillating frequency. b Increase in drop-out time (6 to 10 times the normal time). b Polarised component. CAD c c 24250 V
LAD 4DDL
0.012
Bidirectional peak limiting diode

b Protection provided by limiting the transient overvoltage value to 2Uc maximum. b Maximum reduction of transient voltage peaks. CAD a a 24 V LAD 4TB a 72 V LAD 4TS CAD c c 24 V LAD 4TBDL c 72 V LAD 4TSDL c 125 V LAD 4TGDL c 250 V LAD 4TUDL c 600 V LAD 4TXDL
0.012 0.012 0.012 0.012 0.012 0.012 0.012
LAD 4DDL ou LAD 4T pDL
(1) These contact blocks cannot be used on low consumption control relays. (2) With extended scale from 0.1 to 0.6 s. (3) With switching time of 40 ms 15 ms between opening of the N/C contact and closing of the N/O contact. (4) Power should not be simultaneously applied or maintained to the mechanical latching block of the CAD N. The duration of the control signal to the mechanical latching block and the CAD N should be u 100 ms. (5) Standard control circuit voltages (for other voltages, please consult your Regional Sales Office): Volts a and c 24 32/36 42/48 60/72 100 110/127 220/240 256/277 380/415 Code B C E EN K F M U Q (6) CAD pp d.c. and low consumption control relays are fitted with a built-in bi-directional peak limiting diode suppressor as standard. On control relays produced after 15th July 2004, this diode is removable. It can therefore be replaced by the user (see references LAD 4T ppp above). It can also be replaced by a freewheel diode LAD 4DDL . If a d.c. or low consumption control replay is used without suppression, the standard suppressor should be replaced with a blanking plug LAD 9DL.
Illustrations: page 7/20
Schemes : page 7/25
7/22
References

Accessories and spare parts
Accessories (to be ordered separately)

Description For marking Sheet of 64 blank legends, self-adhesive, 8 x 33 mm For mounting on CAD, LAD (4 contacts) Sold in lots of 10 Unit reference Weight kg 0.020 0.020 0.200
LAD 21 LAD 22
Sheet of 112 blank legends, LAD (2 contacts), self-adhesive, 8 x 12 mm LAD T Strips of blank, self-adhesive All products legends for printing by plotter (4 sets of 5 strips) SIS Label labelling Multi-language version: software for legends LAD 21 English, French, German, and LAD 22, supplied on Italian, Spanish CD-Rom Legend holder, snap-in, LC1 D09...38 8 x 18 mm LC1DT20...40 LADN (4 contacts) LAD T, LAD R For protection Sealing cover LAD T, LAD R Safety cover preventing CAD access to the moving contact carrier 35
LAD 24
XBY 2U
0.100
SIS-L
s uette are ion d'tiq ette softw di crat oftware etiquetas etich lling ione Labe iel de ngss crear Logic hriftu para la creaz Besc are per Softw are Softw
abel
Gerin n Merlin Modico D canique Square Teleme
100
LAD 90
0.001
XBY 2U
1 1
LA9 D901 LAD 9ET1
0.005 0.004
Spare parts: coils

LA9 D901 Specifications b Average consumption at 20 C: - inrush (cos = 0.75) 50/60 Hz: 70 VA at 50 Hz, - sealed (cos = 0.3) 50/60 Hz: 8 VA at 60 Hz, b Operating range ( < 60 C): 0.85 to 1.1 Uc Control circuit Average resistance Inductance of Reference (1) voltage Uc at 20 C 10 % closed circuit 50/60 Hz V V H 12 6.3 0.26 LXD 1J7 21 (2) 5.6 0.24 LXD 1Z7 24 6.19 0.26 LXD 1B7 32 12.3 0.48 LXD 1C7 36 LXD 1CC7 42 19.15 0.77 LXD 1D7 48 25 1 LXD 1E7 60 LXD 1EE7 100 LXD 1K7 110 130 5.5 LXD 1F7 115 LXD 1FE7 120 159 6.7 LXD 1G7 127 192.5 7.5 LXD 1FC7 200 LXD 1L7 208 417 16 LXD 1LE7 220/230 539 22 LXD 1M7 (3) 230 595 21 LXD 1P7 230/240 645 25 LXD 1U7 (4) 277 781 30 LXD 1W7 380/400 1580 60 LXD 1Q7 400 1810 64 LXD 1V7 415 1938 74 LXD 1N7 440 2242 79 LXD 1R7 480 2300 85 LXD 1T7 2499 LXD 1S7 500 575 3294 LXD 1SC7 600 3600 135 LXD 1X7 690 5600 190 LXD 1Y7 (1) The last 2 digits in the reference represent the voltage code. (2) Voltage for special coils fitted in control relays with serial timer module with 24 V supply. (3) This coil can be used on 240 V at 60 Hz. (4) This coil can be used on 230/240 V at 50 Hz and on 240 V only at 60 Hz.
Weight kg 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070
LAD 9ET1
LXD 1
Schemes : page 7/25
7/23

7
Dimensions
CAD a CAD c or LC (low consumption)
c c1 c2 c3
12,5 (LAD 8)
45 c1 c2 c3
45
CAD
b c
32 50
77 84 86 117 129 137 141
323 503
99 84 86 117 129 137 141
CAD
b c
32 50
77 93 95 126 138 146 150
323 503
99 93 95 126 138 146 150
without cover or add-on blocks with cover, without add-on blocks c1 with LAD N or C (2 or 4 contacts) c2 with LAD 6K10 c3 with LAD T, R, S with LAD T, R, S and sealing cover
without cover or add-on blocks with cover, without add-on blocks c1 with LAD N or C (2 or 4 contacts) c2 with LAD 6K10
c3 with LAD T, R, S with LAD T, R, S and sealing cover
Mounting
CAD
Panel mounted Mounted on rail AM1 DP200 or DE200
(1)
=
= = 78
60/70
45
CAD a
CAD c or LC
95 c (AM1 DP200) (2) c (AM1 DP200) (2) (2) With cover
35
CAD a
88 96
CAD c or LC
97 105
with cover
86
(1) 2 elongated holes 4.5 x 9 Mounted on plate AM1 P
AF1 EA4
35
CAD a
c with cover 86
CAD c or LC
95
Characteristics : pages 7/16 to 7/19
60/70
Schemes : page 7/25
7/24
Schemes

Schemes
Instantaneous auxiliary contacts
5 N/O CAD 50
13/NO 23/NO 33/NO 43/NO 03/NO
3 N/O + 2 N/C CAD 32

13/NO 43/NO 44 03/NO 04 21/NC 22 31/NC 32
A1
A2
A1
A2
14
24
34
44

1 N/O + 1 N/C LAD N11
53/NO 61/NC
04
14
LAD 8N11 (1)

161/NC (172) 153/NO (184)
2 N/O LAD N20

53/NO 63/NO
LAD 8N20 (1)

153/NO (184) 163/NC (174)
2 N/C LAD 8N02

151/NC (182) 161/NC (172)
LAD N02
51/NC 52 83/NO 53/NO 61/NC 62
54
62
54
64
152 (181)
53/NO
154 (183)
162 (171)
(1) The figures in brackets are for the device mounted on the RH side of the control relay. 2 N/O + 2F N/C LAD N22
53/NO 83/NO 61/NC 71/NC
1 N/O + 3 N/C LAD N13

53/NO 61/NC 71/NC 81/NC
4 N/O LAD N40

53/NO 63/NO 73/NO 83/NO
4 N/C LAD N04

71/NC 51/NC 61/NC 81/NC
154 (183)
164 (173)
3 N/O + 1 N/C LAD N31

73/NO 74 83/NO 84 61/NC 62
54
62
72
84
54
64
74
84
62
72
82
72
52
2 N/O + 2 N/C including 1 N/O + 1 N/C make before break LAD C22
53/NO 87/NO 61/NC 75/NC
54
With dust and damp protected contacts 2 N/O protected 2 N/C protected
2 N/O protected (2)
62
82
54
2 N/O protected + 2 N/O non protected LA1 DZ40

53/NO 63/NO 73/NO
162 (171)
LA1 DX20
53/NO 63/NO
LA1 DX02
51/NC 61/NC
LA1 DY20
53/NO 63/NO
2 N/O protected + 1 N/O + 1 N/C non protected LA1 DZ31

73/NO 74 61/NC 83/NO 84
54
62
76
88
64
52
62
54
64
54
74
84
54
(2) Product fitted with 4 earth screen continuity terminals.
64
54
62
7
Mechanical latch blocks
LAD 6K10
A1
65/NC
Time delay auxiliary contact blocks

On-delay 1 N/O + 1 N/C LAD T
67/NO 55/NC
LAD S
67/NO 55/NC
Off-delay 1 N/O + 1 N/C LAD R

57/NO
56
68
56
68
58
66
A2
Characteristics : pages 7/16 to 7/19
E2
E1
Schemes : page 7/25
7/25
Selection guide
Zelio Time
Timing relays
Applications
These timing relays enable simple automation cycles to be set up using wired logic. They can also be used to complement the functions of PLCs. Solid state Timing relays with solid state output reduce the amount of wiring required (wired in series). The durability of these timing relays is independent of the number of operating cycles. Relay Relay outputs provide complete isolation between the supply and outut circuits. It is possible to have several output circuits.
Output
Type
Modular
Industrial
Modular
Industrial
Timing ranges
7 ranges: 1 or 2 ranges, 1 s, 10 s, 1 min, 10 min, depending on model: 1 h, 10 h, 100 h 10 s, 30 s, 300 s, 60 min
Depending on model: 6 ranges: 1 s, 10 s, 1 min, 10 min, 1 h, 10 h 7 ranges: 1 s, 10 s, 1 min, 10 min, 1 h, 10 h, 100 h
Depending on model : 4 ranges: 0.6 s, 2.5 s, 20 s, 160 s 7 ranges: 1 s, 10 s, 1 min, 10 min, 1 h, 10 h, 100 h 7 ranges: 1 s, 3 s, 10 s, 30 s, 100 s, 300 s, 10 min 10 ranges: 1 s, 3 s, 10 s, 30 s, 100 s, 300 s, 30 min, 300 min, 30 h, 300 h
Relay type
RE11 Lp pp
RE9
RE11 Rp pp
RE 88 865 ppp RE7
Pages
Please consult our catalogue Automation and relay functions.
7/26
These timing relays enable simple automation cycles to be set up using wired logic. They can also be used to complement the functions of PLCs. Relay Relay outputs provide complete isolation between the supply and output circuits. It is possible to have several output circuits.
Optimum
Plug-in Universal Miniature 7 ranges: 0,1 s...1 s 1 s...10 s 0,1 min...1 min 1 min...10 min 0,1 h...1 h 1 h...10 h 10 h...100 h
Panel-mounted Analogue 14 ranges: 1,2 s, 3 s, 12 s, 30 s, 120 s, 300 s, 12 min, 30 min, 120 min, 300 min, 12 h, 30 h, 120 h, 300 h Digital Depending on model: 7 range : 99.99 s, 999.99 s, 99 min 59 s, 99.99 min, 999.9 min, 99 h 59 min, 999.9 h 11 ranges: 99.99 s, 999.99 s, 9999 s, 99 min 59 s, 99.99 min, 999.9 min, 9999 min, 99 h 59 min, 99,99 h, 999.9 h, 9999 h
1 range, depending on model: 0.5 s, 3 s, 10 s, 30 s, 300 s, 30 min
7 ranges: 1 s, 10 s, 1 min, 10 min, 1 h, 10 h, 100 h
RE8
RE 88 867 ppp
RE XLpTMpp
RE 48A ppp
RE 88 857 ppp
7/27
Selection guide
Zelio Control
Measurement and control relays
Applications
Supply control relays 3-phase 3-phase + neutral
Functions
Control : - rotational direction, - presence of phases, - undervoltage, - overvoltage and undervoltage - asymmetry of phases
Control : - overvoltage and undervoltage - presence of neutral,
Relay output Width
1 or 2 C/O contacts 22.5 mm 45 mm
2 C/O contacts 45 mm
Relay type
RM4 Tppp RM 84 873 004 RM 84 873 299 RM 84 873 5pp
RM 84 873 01p RM 84 873 201 RM 84 873 3pp
RM 84 873 211
Pages
7/28
Voltage measurement relays
Current measurement relays
Control : - overvoltage a 50 mV...5 V a 1..0.100 V a 30..0.500 V
Control : - overvoltage or undervoltage a 50 mV...5 V a 0.2...60 V a 1...100 V a 15...600 V a 30...500 V a 0.2...60 V a 15...600 V a orc 20...80 V a orc 65...260 V 1 or 2 C/O contacts 1 C/O contact 45 mm
Control : Control : - overvoltage and - overcurrent undervoltage 1...20 A with built-in TI
3 mA...1 A
Control : overcurrent and undercurrent 3 mA...1 A 0.3...15 A 2...500 mA 2...500 mA 0.1...10 A 0.1...10 A 10...100 A with built-in TI
1 C/O contact 22.5 mm
2 C/O contacts 22.5 mm
1 C/O contact 17.5 mm 22.5 mm
1 or 2 C/O contacts 45 mm
RM4 UA0pp RM4 UA3p RM 84 872 3pp RM4 UB3p RM 84 871 102 RM4 JA01p RM4 JA31pp RM4 JA32pp RM 84 872 0pp RM 84 871 0pp RM 84 871 3pp
7/29
Selection guide
(continued)
7
Zelio Control
Measurement and control relays
Applications
Liquid level control relays
Functions
Control : - empty
Control : - empty or fill
Relay output Width
1 C/O contact 22.5 mm Plug-in 8 or 11-pin
1 or 2 C/O contacts 22.5 mm
Relay type
RM 84 870 1p1
RM 84 870 30p RM 84 870 807
RM4 Lpppp RM 84 870 00p
Pages
7/30
Liquid level control relays
Motor control relays
Control : - empty or fill with alarm
Control : - empty and fill
Control : - underspeed
Control : - overload and underload (cos ) 2 C/O contacts
2 C/O contacts 45 mm
1 C/O contact
1 C/O contact Plug-in 8 or 11-pin
1 C/O contact 45 mm
RM 84 870 50p
RM 84 870 604
RM 84 870 40p RM 84 870 808
RM 84 874 30p
RM 84 873 40p
7/31

Control Relays

Uploaded by

Copyright:

Available Formats

Control Relays

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Control Relays

Uploaded by

Copyright:

Available Formats

7/0

Zelio Time: timing relays

Zelio Control: measurement and control relays

mm2 mm2 mm2 mm2 mm2 mm

Max. 2x4 2x4 1 x 1.5 + 1 x 2.5 1 x 1.5 1 x 1.5

Shock resistance (1/2 sine wave, 11 ms) Safety separation of circuits

Control circuit characteristics

CA3 K c 12...250 0.8...1.15 Uc y 0.1 Uc 20 10 000 3W 3W 3 25...35 30...40 10 15 2

References : pages 7/4 and 7/5

Dimensions : page 7/8

Schemes : page 7/9

Contact characteristics of control relays and instantaneous contact blocks

110 80 90 110 > 10 0.5 (see schemes page 7/9)

Operational power of contacts conforming to IEC 60947

110/ 127 48 96 240 17 34 86 7 14 36 1000 2050 5000

References : page 7/6

Dimensions : page 7/8

Schemes : page 7/9

Control relays for a.c. control circuit

b Mounting on 35 mm 7 rail or 4 screw fixing. b Screws in the open "ready-to-tighten" position.

Screw clamp connections

Spring terminal connections

Faston connectors, 1 x 6.35 or 2 x 2.8

Solder pins for printed circuit boards

Control relays for d.c. control circuit

Screw clamp connections

Spring terminal connections

Faston connectors, 1 x 6.35 or 2 x 2.8

Solder pins for printed circuit boards

Characteristics : pages 7/2 and 7/3

Dimensions : page 7/8

Schemes : page 7/9

Low consumption control relays (d.c. control circuit)

Control circuit Consumption

Basic reference, to be completed by adding the voltage code (1)

Screw clamp connections

Spring terminal connections

Faston connectors, 1 x 6.35 or 2 x 2.8

Solder pins for printed circuit boards

Characteristics : pages 7/2 and 7/3

Dimensions : page 7/8

Schemes : page 7/9

Instantaneous auxiliary contact blocks

Clip-on front mounting, 1 per control relay

Screw clamp terminals

Faston connectors 1 x 6.35 or 2 x 2.8

Electronic time delay contact blocks

Clip-on front mounting, 1 per control relay

Characteristics : page 7/3

Dimensions : page 7/8

Schemes : page 7/9

Suppressor modules incorporating LED indicator

110/120 mm fixing centres

Clip-on fixing on front face

4 maximum per relay

Strips of 10 identical numbers 0 to 9 Strips of 10 identical capital letters A to Z

Dimensions : page 7/8

On mounting rail AM1 DP200 or AM1 DE200 (7 35 mm)

Electronic time delay contact blocks

Characteristics: pages 7/2 and 7/3