Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 128 views

    Gas Analyzer

    Uploaded by

    engine5
    The gas analyzer performs a self-test when switched on and requires warming up before use. It samples vehicle exhaust using an internal pump and probe, and contains a water separation system to reduce maintenance. When recording with a PowerLab, connect the gas analyzer to it and start LabChart recording after allowing warmup time, ensuring the pump is on while breathing across the sampling tubing to record gas concentrations.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Gas Analyzer

    Uploaded by

    engine5
    128 views5 pages
    The gas analyzer performs a self-test when switched on and requires warming up before use. It samples vehicle exhaust using an internal pump and probe, and contains a water separation system to reduce maintenance. When recording with a PowerLab, connect the gas analyzer to it and start LabChart recording after allowing warmup time, ensuring the pump is on while breathing across the sampling tubing to record gas concentrations.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The gas analyzer performs a self-test when switched on and requires warming up before use. It samples vehicle exhaust using an internal pump and probe, and contains a water separation system to reduce maintenance. When recording with a PowerLab, connect the gas analyzer to it and start LabChart recording after allowing warmup time, ensuring the pump is on while breathing across the sampling tubing to record gas concentrations.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    128 views5 pages

    Gas Analyzer

    Uploaded by

    engine5
    The gas analyzer performs a self-test when switched on and requires warming up before use. It samples vehicle exhaust using an internal pump and probe, and contains a water separation system to reduce maintenance. When recording with a PowerLab, connect the gas analyzer to it and start LabChart recording after allowing warmup time, ensuring the pump is on while breathing across the sampling tubing to record gas concentrations.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    Using the Gas Analyzer

    When first switched on, the Gas Analyzer performs an initial self-test, and it should then be allowed time to warm up. When used with a PowerLab and LabChart, the Gas Analyzer has default scaling and units, and so can be used without further setting up.

    Power-up Test of the Gas Analyzer


    The Gas Analyzer performs an initial check when it is switched on. 1. Ensure dust caps are removed from both the Sample In and Exhaust ports of the Gas Analyzer, and that the Exhaust port is clear of obstruction. 2. Turn on the Gas Analyzer. Its Power indicator should glow blue. 3. Check the internal pump by flicking the Pump On switch. Its indicator should glow yellow and the pump may be heard. Allow at least 10 minutes of operation with the pump on before recording with the Gas Analyzer. Until it has warmed up, the output from the CO 2 transducer may be unusable due to a large offset.

    Operation
    The AGS688 samples the vehicles exhaust gas by means of an internal pump and high temperature resistant exhaust probe. Using the keypad, it is possible to set the date and time, and produce an immediate printout of all the results. The AGS688 contains a revolutionary newly designed water separation system. This considerably reduces the gas path length and maintenance schedules. The separation unit is injection-moulded and consists of two filters, a mechanical water separation filter and a fibre-based coalescent filter. A single axle, dual head pump assembly allows for continuous removal of water which

    condenses in the separator. The AGS688 has gas-in and fresh-air (autozero) inputs, and a dedicated calibration gas input connection.

    Recording
    After connecting the Gas Analyzer to a PowerLab, with the PowerLab connected to your computer, connect the sampling tubing to the gas sample inlet of the Gas Analyzer using the in-line hydrophobic filter and Nafion tubing (to remove moisture). The analog signals from the Gas Analyzer are linear and proportional to the concentrations of CO2 and O2 (01 V from the CO2 output is equivalent to 010% CO2 and 0.051 V from the O2 output is equivalent to 5100% O2). These are approximate voltages and some variation from these values can occur. 1. Perform the power-up test for the Gas Analyzer as described in the previous section. Allow the Gas Analyzer at least 10 minutes warm-up time before use. 2. Turn on your PowerLab. It should perform its normal diagnostic tests, as described in the owners guide. 3. Start LabChart. The Status indicator of the Gas Analyzer should glow green. A suggested initial sampling rate is 20 /s. 4. To preview the signal from the Gas Analyzer, or to adjust the range or lowpass filter settings, choose Carbon Dioxide (or Oxygen) from the relevant Channel Function popup menu. The Carbon Dioxide (or Oxygen) dialog appears

    The default Range is 10% for the Carbon Dioxide input and 100% for the Oxygen input. The default Low-pass filter setting is 5 Hz. You can record data in absolute or difference modes. The difference mode can be used to record changes in gas concentration from an ambient level. Select the CO2 (or O2) checkbox to use the difference mode. When in difference mode, click the Zero button to remove any offset in the signal

    Click the Units button to open the Units Conversion dialog, with which you can enter different values for the channel, as described under "Calibrating with LabChart", doing so deselects the Use default units checkbox. To revert to the default settings again, and so replace any previous settings made in the Units Conversion dialog, select the Use default units checkbox. The default settings are shown

    5. Start recording in LabChart. Ensure the pump is on and breathe across, not directly into, the sampling tubing opening to record gas concentrations.

    How it Works
    The Gas Analyzer has an infra-red transducer to measure CO2 concentration and a visible spectrum transducer to measure oxygen concentration. It has a response time of about 0.2 s (at ~200 ml/min) and can be used to indicate CO2 and O2 trends in exercising humans and small animals. The variable speed pump draws sample gas through the two transducers. The pump can be set to any flow rate in the range 35 ml/min to 200 ml/min.

    O2 Transducer
    The O2 transducer is an Oxigraf X2004 sensor which uses absorption spectroscopy in the visible spectrum (760 nm). Narrow-band light supplied by a laser diode, thermally tuned to a particular emission-line in the oxygen spectrum, is directed across a chamber containing the incoming gas sample. A detector on the opposite side of the chamber detects any attenuation in the light intensity at the wavelength of interest. As the concentration of oxygen in the chamber increases, more energy is absorbed by the oxygen molecules in the gas and less light is received by the detector.

    CO2 Transducer
    The CO2 transducer is a Servomex model 1507 infrared transducer. It is calibrated so that output voltages in the range 01 V are proportional to CO2 concentrations in the range 010%. The optical path, generation and detection system is an amplitude modulated carrier system.

    Considerations When Using the Gas Analyzer


    The sample inlet and exhaust ports on the Gas Analyzer should remain clear. Unnecessary dead-space in the gas path should be kept to a minimum. Chemical contamination and rubber compounds should be avoided. The sample gas dewpoint should be at least 10 C below transducer temperature. The sample gas should be free of oil contaminants, particles and liquids or condensing vapors. In humid environments, or when sampling from exercising subjects, dry the sample using desiccant. Removing moisture will lengthen the life of the transducers.

    You might also like