1. This document summarizes the calculation of the moment capacity of a single angle member based on ANSI/AISC 360-05 provisions.
2. It considers yielding, lateral-torsional buckling, and leg local buckling limits and selects the minimum of these as the nominal flexural strength.
3. The calculations determine that the maximum factored moment of 3.81 kN-m is 56.5% of the reduced design flexural strength of 6.74 kN-m, indicating the design is adequate.
1. This document summarizes the calculation of the moment capacity of a single angle member based on ANSI/AISC 360-05 provisions.
2. It considers yielding, lateral-torsional buckling, and leg local buckling limits and selects the minimum of these as the nominal flexural strength.
3. The calculations determine that the maximum factored moment of 3.81 kN-m is 56.5% of the reduced design flexural strength of 6.74 kN-m, indicating the design is adequate.
1. This document summarizes the calculation of the moment capacity of a single angle member based on ANSI/AISC 360-05 provisions.
2. It considers yielding, lateral-torsional buckling, and leg local buckling limits and selects the minimum of these as the nominal flexural strength.
3. The calculations determine that the maximum factored moment of 3.81 kN-m is 56.5% of the reduced design flexural strength of 6.74 kN-m, indicating the design is adequate.
1. This document summarizes the calculation of the moment capacity of a single angle member based on ANSI/AISC 360-05 provisions.
2. It considers yielding, lateral-torsional buckling, and leg local buckling limits and selects the minimum of these as the nominal flexural strength.
3. The calculations determine that the maximum factored moment of 3.81 kN-m is 56.5% of the reduced design flexural strength of 6.74 kN-m, indicating the design is adequate.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 3
DWG.
ru Projet:
Site:
Fait par: CpL Date: 2010-12-02 Verif. par: Classement
Dfinition
SINGLE ANGLE moment capacity calculation (Chapter F of ANSI/AISC 360-05)
M u := 3.81kN m Fy := 300MPa - resultant flexural moment due to factored loads := 0.9
Angle L102*102*7.9 b := 4in = 101.6 mm t := 5 16 in = 7.94 mm
y' := 1.11in = 28.19 mm Sc := 1.27in = 20.81 10 mm
3 3 3
- elastic section modulus from dimentions and properties table
1.Yelding Sw := 1.27in 3
- elastic section modulus to the leg tip about the major principal axis
M y1 := Fy Sw = 6.24 kN m- yield moment about geometrical axis M n1 := 1.5M y1 = 9.37 kN m- nominal flexural strength
M max := M u = 3.81 kN m M a := 2850N m M b := 3810N m M c := 2850N m Rm := 1.0 - absolute value of maximum moment in the unbraced segment - absolute value of moment at quarter point of the unbraced segment - absolute value of moment at centerline of the unbraced segment - absolute value of moment at three-quarter point of the unbraced segment - for singly symmetric members subjected to single curvature bending (for other see page 16.1-46 ANSI/AISC 360-05)
1/3
DWG.ru Projet:
Site:
Fait par: CpL Date: 2010-12-02 Verif. par: Classement
Cb :=
12.5M max 12.5M max Rm if Rm < 1.5 = 1.14 2.5 Mmax + 3 Ma + 4 Mb + 3Mc 2.5 Mmax + 3 Ma + 4 Mb + 3Mc 12.5M max 1.5 if Rm > 1.5 2.5 Mmax + 3 Ma + 4 Mb + 3Mc
Elastic lateral-torsional buckling moment calculation:
Le := 3040mm ATTENTION: - laterally unbraced length of a member To choose - the bending is about one of the geometric axes of an equal-leg angle with lateral-torsional restraint at the point of maximum moment (NO or YES): a1 :=
k e :=
1 if a1 = 1 1.25 if a1 = 2
=1
k y :=
0.8 if a1 = 1 1 if a1 = 2
= 0.8
ATTENTION:
To choose - type of the stress at the toe (COMPRESSION or TESION):
a2 :=
2 0.66 E b 4 t C Le t b M e := k e 1 + 0.78 2 b2 Le 2 0.66 E b 4 t C Le t b + k e 1 + 0.78 2 b2 Le
1 if a2 = 3 1 if a2 = 4
M e = 45.27 kN m M y2 := M y1 k y = 4.99 kN m
2/3
DWG.ru Projet:
Site:
Fait par: CpL Date: 2010-12-02 Verif. par: Classement
M n2 :=
0.17M e = 7.49 kN m 0.92 Me if Me My2 M y2 M 1.92 1.17 y2 M if M > M 1.92 1.17 My2 M 1.5M e y2 y2 M e y2 M e y2 M y2 (1.5My2) if 1.92 1.17 M My2 > 1.5My2 e
3.Leg Local Buckling
Width_Thickness_Ratio := "Compact" if b t 0.54 E Fy E Fy < b t < b t 0.91 E Fy = "Compact"
"Noncompact" if 0.54 E Fy
"Slender" if 0.91 k s := 1 if a2 = 3 b y' y' if a2 = 4
3
= 2.604
Sc3 := Sc k y k s = 2.65 in M n3 := min M n1 , M n2
if Width_Thickness_Ratio = "Compact"
Fy b if Width_Thickness_Ratio = "Noncompact" Fy Sc3 2.43 1.72 t E 0.71E
b t
Sc3 if Width_Thickness_Ratio = "Slender"
M n3 = 7.49 kN m M n := min M n1 , M n2 , M n3 M r := M n = 6.74 kN m FU := M max Mr OK "OK" if FU < 1 "PAS OK" otherwise
Logical progression of twelve double binary tables of physical-mathematical elements correlated with scientific-philosophical as well as metaphysical key concepts evidencing the dually four-dimensional basic structure of the universe
