Nitoseal MS50

Nitoseal MS50
One part, general purpose building sealant Uses

Nitoseal MS50 is suitable for sealing joints in Concrete, Brickwork, Blockwork, Perimeter sealing around doors and windows, Non-trafficked floor joints.
constructive solutions
Instructions for use Preparation

Joint surfaces must be clean dry and free from all dirt, laitance, loose material and foreign matter. Remove all rust, scale and protective lacquers from metal surfaces. Removal can be achieved by rigorous wire brushing, grinding or grit blasting. Joints in concrete should preferably be sawn. After sawingall saw slurry must be flushed away and the joint allowed to dry. When resealing, the existing sealant should be removed from the joint and the arris cleaned back to sound clean concrete. All debris should be removed. Any expansion joint filler must be checked to ensure it is tightly packed and no gaps or voids exist at the base of the sealing slot before positioning a bond breaker. The use of a bond breaker is not required in expansion joints containing cellular polyethylene joint filler such as Hydrocell XL* . For construction or contraction joints, a bond breaker tape or back-up strip must be used. Where a particularly neat finish is required, mask the face edges of the joint before sealing and remove immediately after tooling is completed.
Advantages
Excellent adhesion to most common building materials Single component with fast rate of cure Easy to apply at low temperature Can be applied to damp substrates Environmentally friendly Primer-less for most applications (see Priming) Available in a range of colours (see Properties) Isocyanate free technology
Description
Nitoseal MS50 is a one part, medium modulus sealant based on hybrid silyl modified polyether technology.
Specification
Where shown on the contract documents, the one part sealant shal be Nitoseal MS50 supplied by Fosroc. It shall provide good UV protection and have a movement accommodation factor of 20%.
Priming
In joints where limited movement is expected, a primer is not normally required. In joints subject to high movement or intermittent immersion during service, Fosroc Primer MS1 is recommended. Prime the joint face using a clean, dry brush. Avoid over application of primer causing puddles in the bottom of the joint. Nitoseal MS50 should be applied between 30 minutes and 4 hours after priming. If a joint is left unsealed for more than 4 hours, the primer should be removed by grit blasting or grinding and the joint reprimed. Please contact your local Fosroc representative for any clarifications on priming.
Properties
Form Flash point Colour Smooth, non-slumping paste >65C White, Grey, Black, Portland Buff, Rustic Red, Brown
Movement accommodation factor Skinng time (@20C / 50% RH) Cure rate (@20C/50% RH) 24 hours 48 hours 72 hours Application temperature
Nitoseal MS50
20%
30 minutes
Application
: 3mm : 6mm : 8mm : 5 - 50C Cut the end off the sachet and place in the Fosroc GX gun. Fit the nozzle and cut at 45 at a suitable size for sealing the joint. Extrude the sealant firmly into the joint. Tool flush within 5 minutes of application to ensure good contact between the sealant and the substrate.
Typical hardness (Shore A at 20C) UV resistance
: 45 : Good
Cleaning
Clean tools immediately after use with Nitoflor Sol.
Nitoseal MS50
Estimating Supply
Nitoseal MS50 : 10 no x 600ml sachets per box. Fosroc Primer MS1 : 200ml packs Guide to sealant quantities Joint size in mm 6x10 12x10 20x20 25x12 30x15 40x20 Litre per metre run 0.060 0.120 0.400 0.300 0.450 0.800 Metre per 600ml sachet 10.00 5.00 1.50 2.00 1.33 0.75
Storage
When stored in warehouse conditions below 350C, Nitoseal MS50 will have a shelf life of 12 months.
Precautions Health and safety

Nitoseal MS50 is considered safe in normal use. However, as with any material, good hygiene practices should be followed, i.e. keep out of eyes, do not consume, keep away from children and pets, wash hands thoroughly after use.
Fire
Nitoseal MS50 is non flammable while Fosroc Primer MS1 is flammable. Please refer to the Material Safety Data Sheet for details.
Additional Information
Fosroc manufactures a wide range of complementary products which include : waterproofing membranes & waterstops cementitious & epoxy grouts specialised flooring materials For further information on any of the above, please consult your local Fosroc office - as below.
0.5 litres of Fosroc Primer MS1 will be sufficient for 60m of joint. No allowance has been made for joint dimensions or wastage .
Limitations
For continuous water immersed conditions, use Nitoseal MS600 For trafficed floor joints, use Nitoseal MS300 Not suitable for contact with Bituminous materials. Not suitable for contact with solvents, oil or petrol. Overcoating of the sealant will reduce the MAF of the sealant.
Denotes the trademark of Fosroc International Limited Important note :

Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard terms and conditions of sale, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice, recommendation specification or information it may give is accurate and correct, it cannot, because it has no direct or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products whether or not in accordance with any advice, specification, recommendation or information given by it. telephone ++91 80-22240018/120 fax ++91 80-22233474 e-mail india@fosroc.com
Fosroc Chemicals (India) Pvt. Ltd. Head Office

111/3, Hafeeza Chamber II Floor, K H Road, PBNo. 2744, Bangalore 560027
www.fosroc.com Bangalore
Regional Offices Mumbai

208/209, Persepolis Sector 17, Vashi Navi Mumbai 400 703 Ph:022-2789 6412/14 Fax: 022 - 2789 6413 email:Mumbai@fosroc.com
Delhi
First floor,1/2 East Patel Nagar Opp: Vivek Cinema, Main Patel Rd New Delhi 110 008 Ph:011-25884903/4 Fax: 011- 25884422 email:Delhi@fosroc.com
Kolkata
30/B Jodhpur Park Ground Floor Kolkata 700 068 Ph: 033 2472 5482 Fax: 033-2472 9921 email:Kolkata@fosroc.com
Shankar House, IV Floor 1 & 18, RMV Extension Bangalore 560 080 Ph:080-2361 3161/2361 2004 Fax : 080-2361 7454 email: Bangalore@fosroc.com
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bhubaneshwar : (0674) 2521176 Chennai (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2356668 Coimbatore : (0422) 2472966 Goa : (0832) 2542465 Guwahati (0361) 2548793 Hyderabad : (040) 27662324/27662425 Hubli (0836) 3402597 Indore : (0731) 504339/5061477 Jaipur : (0141) 2235349 Lucknow :(0522) 22239044 Nagercoil (04652) 2224849 Mangalore: (0824) 22272234 Visakhapatnam : (0891) 2564850 INDIA/2004/0845/A

Nitoseal MS50

Uploaded by

Copyright:

Available Formats

Nitoseal MS50

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Nitoseal MS50

Uploaded by

Copyright:

Available Formats

Nitoseal MS50

One part, general purpose building sealant Uses

Instructions for use Preparation

Typical hardness (Shore A at 20C) UV resistance

Precautions Health and safety

Denotes the trademark of Fosroc International Limited Important note :

Fosroc Chemicals (India) Pvt. Ltd. Head Office

Regional Offices Mumbai

You might also like