This document provides instructions for daily safety inspections of equipment used in industrial radiography. It outlines 8 steps to calculate radiation exposure from a radioactive source, and details inspection procedures for a radiographic projector, transport cable, and head hose. The inspections are to be done before and after each work shift using a properly calibrated handheld radiation survey instrument to ensure the safety of radiography technicians.
This document provides instructions for daily safety inspections of equipment used in industrial radiography. It outlines 8 steps to calculate radiation exposure from a radioactive source, and details inspection procedures for a radiographic projector, transport cable, and head hose. The inspections are to be done before and after each work shift using a properly calibrated handheld radiation survey instrument to ensure the safety of radiography technicians.
This document provides instructions for daily safety inspections of equipment used in industrial radiography. It outlines 8 steps to calculate radiation exposure from a radioactive source, and details inspection procedures for a radiographic projector, transport cable, and head hose. The inspections are to be done before and after each work shift using a properly calibrated handheld radiation survey instrument to ensure the safety of radiography technicians.
This document provides instructions for daily safety inspections of equipment used in industrial radiography. It outlines 8 steps to calculate radiation exposure from a radioactive source, and details inspection procedures for a radiographic projector, transport cable, and head hose. The inspections are to be done before and after each work shift using a properly calibrated handheld radiation survey instrument to ensure the safety of radiography technicians.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1of 10
At a glance
Powered by AI
The document outlines the daily inspection procedures for radiographic equipment, including calculating radiation levels and ensuring equipment is functioning properly and safely.
Daily inspections must be performed on the projector, cables, and head hose to check for physical damage and abnormal radiation readings. This includes surveying all sides for radiation levels and checking connections and labels are intact.
Personal protective equipment like a TLD badge, alarming dosimeter, and personal dosimeter are required. A hand-held radiation survey instrument must also be used and calibrated properly.
The N.O.R.M. Inc.
Bay 6, 18 Burnt Bluff Street
Red Deer, AB Canada T4N 655 Phone: (403) 755-3912 (24 hrs.) Fax: (403) 755-3908 PROVIDING OUR VALUABLE SERVICES IN THE EASTERN HEMISHPERE PH: 202 2521 8289 FAX: +202 2521 8291 EMAIL: CAIRO@THENORM.CA Email: info@thenorm.ca Website: www.thenorm.ca Morning Calculations Assume; 1. Source: Ir-192 2. 80 Curies upon manufacture date 3. The source is 42 days old 4. Your equipment utilizes a 10M cable and a 3 meter Head Hose 5. The collimator is a 2 TVL Tungsten Shield !gp 1: Calculate Half Life To calculate for "n", H1 = Remaining Curies 2 n WHERE, H1 =Original Curies ~ D a y s Passed "n" = number of half lives passed Known Half Life = Number of Half Lives Passed Therefore 80 =54.2 Curies Remain 2 0.56 42 = 0.56 74 "n" = 0.56 W 2: Convert Curie Amount to GBg units Therefore; 54.42 X 37 =2013.61 GBq "37" is the constant factor when converting Curies (imperial) to GBq (Sievert/metric) !gp 3: Calculate the Specific Output Factor for 2013.61 GBg of Ir-192 The SOF of Ir-192 "Special Form R/A Material" is; 0.15 mSv/hr/Gbq @ 1 meter Therefore; 2013.61 X 0.15 =302.041 mSv/hr @ 1 meter .Np 4: Convert mSv to uSv 302.041 X 1000 =302,041 uSv/hr @ 1 meter This is where the urgency of RADIATION SAFETY and ALARA practices begin to make sense to the operator! !gp 5: Calculate the intensity of the "COLLIMATED (2 TVL) Source T1 = T2 10 n Therefore; 3 0 ~ 4 1 = 3,020 uSv/hr @ 1 meter "collimated Where; T1 = Calculated Source Intensity T2= The "Shielded" Intensity "n"= Number of TVL !gp 6: Calculate the intensity of the "collimated" source at 13 meters ~ ' O I' DO 0 Therefore; 3,020 = 13 1 2 3,020 = 169 (i) 17.87 uSv/hr @ 13 meters "collimated" The Equation: 2 io =D - - 2 i Do gm 7: Calculate DOSE/Shot For this example let's assume that your shot time is 1 seconds... DOSE =Dose Rate X Time Where; DOSE =Accumulated Dose Dose Rate = As calculated OR measured on a working calibrated survey instrument Time = "calculated" time of exposure Therefore; Dose = 17.87 X -l 3600 = 17.87 X 0.002 DOSE = 0.036 uSv/shot gm 8: Daily "Calculated Dose" Let's assume 20 shots/hr for 8 hours 20 X 8 = 160 Shots 160 X 0.036 = 5.76 uSv (0.58 mR) J THIS CAN BE MADE TO BE LOWER DO NOT FORGET... There is 7 seconds of travel through the head hose while the source is UNSHIELDEIJ1!! Let's Review... 1. Calculate your HALF LIFE (Now enter the remaining curie amount into your calculator **LEAVE THIS NUMBER ON YOUR DISPLAY** 2. Remaining Curies X 37 (Constant Factor required to calculate GBq activity 3. Your source has an SOF ("x" 0.15 mSv/hr/GBq) 4. Convert this number to either uSv/hr (X 1000) OR mR/hr (X 100) 5. Calculate Shielding effectiveness (divide by 100 as this is a 2 TVL collimator) **You nowknowthe intensity of the collimatedsource at 1 meter** 6. Calculate the intensity of the source at the cable crank where you stand 10 d 2 7. Calculate your TOTAL DOSE at the "intended" distance **DOSE = DOSE RATE X TIME** More to do... You must also calculate the distance to your Safe Working Perimeter (SWP) 0 2 = io X d0 2 I Is it your company policy to calculate SWP with an "unshielded" source? (it should be) NUMBERS do not lie... they ONLY speak truth. These calculations will lend confidence In your technician's daily operations. If your operator accomplishes a TOTAL DOSE (+/- 20%) of the "TRUE" dose received they have accomplished our (client/service provider) collective goal. NOTE: The following should be done DAILY both BEFORE and AFTER the daily inspections carried out by the technician HAND HELD Survey Instrument 1. Check the physical condition of the instrument Is it clean? When you shake it do you hear any rattling? Is the instrument face clear of moisture or debris? Do you feel confident using it to PROTECT yourself? 2. Check the Calibration Date sticker on the instrument Is there one? Has it been calibrated within 365 days of this moment? 3. Turn it on Check battery function... does it have sufficient battery power? Turn it to LOW and walk toward the storage area. Does the dose rate increase? NOTES; It is NOT a Radiation Survey Meter. .. it is called a HAND HELD RADIATION SURVEY INSTRUMENT This means that this survey instrument MUST be held in hand. This means that this Must be within 1 meter of the technician at all times when radiographic inspection projector is operational. Operational means that the equipment is NOT in the shielded confines of the transport box OR within the locked storage area at the facility. Daily Radio9.@J?hic Projector Inspection 1. Survey the sides of the device. (ALL 6 SIDES!) are at or below 200 mR/hr 2. Make sure the source tag (BRASS OR STEEL) is securely fastened to the back of the Projector. 3. Make sure the pigtail/cable connection cap is secure 4. Check ALL labels on the device. Are they legible? 5. Check the projector cap on the front of the device. Is it secure? 6. Check the bottom of the device for wear as well as the other 5 sides. REMEMBER... the shielding within is U-234 which is also radioactive! 7. If all is in check, place the projector into the transport box and lock the transport box. 8. Pick up your HAND HELD radiation survey instrument and measure the transport index both on the skin of the vehicle and at 1 meter. Also measure the dose rate inside the passenger and driver area of the vehicle. Cable Inspection (Length is Critical - 25 to 50 feet is mandatory), 1. Survey the cables with your HAND HELD radiation survey instrument 2. Physical condition (this is done with your hands and eyes) 3. Inspect the crank 4. Inspect the housing and cover 5. Inspect the cable end projector connector 6. Inspect the cable pigtail connector (use your NO GO GAUGE!) 7. Crank out 1 meter of cable. Inspect the cable for wear (visual) 8. Bend the cable in all directions. If you feel snapping DO NOT USE! 9. Crank the cable back into the housing with extreme force. Make sure the cable end does not disappear into the cable housing. VERY IMPORTANT! Head Hose Inspection 1. Survey the head hose with your HAND HELD radiation survey instrument 2. Visually inspect the complete length of the head hose 3. While visually inspecting the head hose run your hands over it feeling for dents or kinks 4. Inspect the projector connection for damage 5. Inspect the guide tube tip to make sure it is securely fastened to the head hose Make sure that before performing these inspections that you are wearing the following; TLD Badge Alarming Dosimeter Personal Dosimeter (zeroed every day) And that your HAND HELD radiation survey instrument is functioning properly REMEMBER These inspections are to be done at the beginning and end of EVERY shift. A complete survey of the projector and guide tube must be done with your HAND HELD radiation survey instrument after EACH AND EVERY projection throughout the day. These steps are for your and other's safety when actively performing radiographic inspection.