FM 3-3

FMFM 11-17

Chemical and Biological

Contamination Avoidance

This copy is a reprint which includes current

Pages from Change 1.

HEADQUARTERS, DEPARTMENT OF THE ARMY

COMMANDANT MARINE CORPS

DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited.

 Field Manual *FM 3-3/FMFM 11-17
No. 3-3 HEADQUARTERS
Fleet Marine Force Manual DEPARTMENT OF THE ARMY
No. 11-17 Washington, DC, 16 November 1992

Chemical and Biological

Contamination Avoidance
Table of Contents

DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited.

i
FM 3-3

ii
FM 3-3

iii
FM 3-3

iv
 C1, FM 3-3/FMFM 11-17

Change 1 HEADQUARTERS
DEPARTMENT OF THE ARMY
US MARINE CORPS
Washington, DC, 29 September 1994

Chemical and Biological Contamination Avoidance

FM 3-3/FMFM 11-17, 16 November 1992, is changed as follows:
1. New or changed material is indicate by a BAR ( ).
2. Distribution restriction statement identified on this change replaces the one shown on basic
publication dated 16 November 1992.
3. Remove old pages and insert new pages as indicated below:
4. File this transmittal sheet in front of the publication.
Remove Old Pages Insert New Pages
1-5 thru 1-6 1-5 thru 1-6
2-1 thru 2-2 2-1 thru 2-2
2-3 thru 2-4 2-3 thru 2-4
3-3 thru 3-4 3-3 thru 3-4
3-5 thru 3-6 3-5 thru 3-6
3-9 thru 3-10 3-9 thru 3-10
3-11 thru 3-12 3-11 thru 3-12
3-13 thru 3-14 3-13 thru 3-14
3-15 thru 3-16 3-15 thru 3-16
3-17 thru 3-18 3-17 thru 3-18
3-19 thru 3-20 3-19 thru 3-20
3-21 thru 3-22 3-21 thru 3-22
4-1 thru 4-2 4-1 thru 4-2
4-13 thru 4-14 4-13 thru 4-14
4-15 thru 4-16 4-15 thru 4-16
5-3 thru 5-4 5-3 thru 5-4
5-11 thru 5-12 5-11 thru 5-12
5-17 thru 6-0 5-17 thru 6-0
A-15 thru B-0 A-15 thru B-0
B-1 thru B-2 B-1 thru B-2
Glossary-1 thru Ref-0 Glossary-1 thru Ref-0
Ref-1 thru Index-0 Ref-1 thru Index-0
DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited.

MARINE CORPS PCN: 13971190001

By Order of the Secretary of the Army:

GORDON R. SULLIVAN
General, United States Army
Official: Chief of Staff

MILTON H. HAMILTON
Administrative Assistant to the
Secretary of the Army
07244

By Order of the Marine Corps:

CARL E. MUNDY, JR.

Commandant
United States Marine Corps

DISTRIBUTION:
Active Army, USAR, and ARNG: To be distributed in accordance with DA Form 12-11 E,
Requirements for FM 3-3, Chemical and Biological Contamination Avoidance, (Qtr rqr block 3829).
 FM 3-3

Preface

The mission of the Chemical Corps is to prepare the easy-to-read, step-by-step manual depicting the manual
Army to survive and win in a Chemical and Biological method of calculating CB contamination avoidance
(CB) warfare environment by - procedures for chemical officers and NCOs. However,
Developing doctrine, organizations, training subject matter discussed in Chapters 1 and 2 and
products, and equipment for CB defense, chemical Appendices A and C are of general use for all branches
retaliation, and smoke and flame operations. and MOS.
Minimizing the impact of CB weapons through Chapter 1 defines the CB Threat, how to reduce unit
contamination avoidance, protection, and vulnerability, and implements STANAG 2984, graduated
decontamination. levels of NBC Threat and minimum protection.
Employing smoke. Chapter 2 defines how we warn our troops of an
Employing flame. enemy CB attack and how we warn of a friendly
This manual is one of five that explains the chemical attack.
fundamentals of NBC defense: Chapters 3, 4, 5, and 6 detail procedures for
FM 3-3, Chemical and Biological Contamination detecting, identifying, evaluating and plotting hazards
Avoidance. while operating in an CB environment. These chapters
FM 3-3-1, Nuclear Contamination Avoidance. are essential for battalion, brigade, and division chemical
FM 3-4, NBC Protection. personnel.
FM 3-5, NBC Decontamination. Appendix A provides operational situation guidelines
FM 3-7, NBC Handbook for the principles of contamination avoidance in the form
A general overview of these fundamentals is given in of a checklist.
FM 3-100, NBC Operations. This manual, FM 3-3, Appendix B provides supplemental information on
defines and clarifies the entire process of CB biological agents and a list of country codes used in
contamination avoidance. Another manual, FM 3-3-1, processing biological samples.
outlines contamination avoidance procedures for nuclear Chemical personnel must be familiar with and be able
operations. This manual has limited distribution to apply the information in this manual.
specially for separate brigades, division, and corps level The proponent of this manual is the U.S. Army
NBC Control Centers. Unless otherwise stated, Chemical School. Submit changes for improving this
whenever the masculine gender is used, both men and publication on DA Form 2028 (Recommended Changes
women are included. to Publications and Blank Forms) and forward to:
FM 3-3 details the NBC Warning and Reporting
System, how to locate and identify CB contamination, Commandant
and how to operate in and around NBC contamination. US ACML&MPCEN&FM
This manual is designed and intended to be an ATTN: ATZN-CM-FNB
5th Avenue, Bldg 1081
Fort McClellan, AL 36205-5020.

v
FM 3-3

Introduction

Contamination avoidance is the best defense against

enemy use of chemical and biological (CB) weapons. Implement Passive
Avoidance reduces the risk of being targeted by CB Defensive Measures
agents and minimizes the effects of CB contamination Passive defensive measures are those measures taken
hazards. Knowing where contamination exists or how to reduce the probability of being hit by a CB attack or,
long the hazard may persist is essential to avoiding the if hit, to reduce the effects of the attack. Operational
hazard. Enemy use of CB weapons make battlefield security measures such as good communication
operations more difficult and time consuming. Combat, procedures, light discipline, and good camouflage reduce
combat support, and combat service support operations the chances of a unit being targeted. Dispersion,
may be more difficult to perform in a CB environment. hardening of positions and equipment, and using
Tasks/missions may take more time, but they require overhead cover reduces the effectiveness of an attack.
prior training in Mission Oriented Protective Posture Passive measures are discussed in more detail in Chapter
(MOPP) gear because of the problems created by CB 1.
contamination. CB attacks may cause casualties,
materiel losses, and creation of many obstacles.
Training will reduce the problems caused by CB attacks Warn and Report
on the unit. Units must locate clean areas as well as Once a CB attack has occurred everyone who might
locate contamination in an CB environment. be affected by the hazard must be warned. This gives
Contaminated units will have to perform units time to protect themselves against a possible
decontamination (decon) operations. hazard. The NBC Warning and Reporting System
To survive and accomplish the mission, individuals (NBCWRS) is used for warning and reporting CB
and units must take precautions to avoid or minimize hazards. These messages and their use are standardized
effects of initial and residual CB hazards. The threat of and kept simple so they can be passed rapidly and be
contamination may force individuals and units into easily understood. The NBCWRS is discussed in
MOPP gear or into collective protection. Wearing Chapter 2. The Automated NBC Information System
MOPP gear results in heat buildup and degrades (ANBACIS) will assist in speeding this process.
individual performance. Using collective protection
requires special procedures that are time consuming. Locate and Identify,
See FM 3-4 for information on what measures or steps
an enemy CB attack may affect friendly forces. FM 3-3 Track and Predict
outlines how to anticipate an enemy CB attack and
minimize the effects on friendly forces. NBC Hazards
By locating, identifying, tracking, and/or predicting
CB hazards, commanders can make informed decisions
Contamination Avoidance for operating in or around NBC hazards. Planning CB
There are four steps to contamination avoidance: reconnaissance is discussed in Chapter 5. Tactics and
implement passive defensive measures, warn and report techniques of CB reconnaissance are contained in FM
CB attacks, locate, identify, track and predict CB 3-19, NBC Reconnaissance. Techniques for predicting
hazards, and limit exposure to CB hazards. If the CB hazards are given in Chapters 3 and 4. A portion of
mission permits, avoiding CB hazards completely is the ANBACIS provides for the automatic calculation of
best course of action. This is not always possible. The hazard areas due to chemical or biological weapons
mission may force you to occupy or cross a using or creating all NBC 1 through NBC 5 Reports.
contaminated area. This manual outlines procedures to
use when working or training to work in a contaminated
environment. Using these procedures, which are Limit Exposure
summarized by the four steps of contamination If operation in a contaminated area is necessary, take
avoidance, units can minimize performance degradation. steps to limit the amount of troop exposure. Chapters 3
and 4 discuss crossing contaminated areas. FM 3-4,
NBC Protection, gives guidance on protective measures

vi
 FM 3-3

for such crossings and FM 3-19, NBC Reconnaissance, combat service support units and to protect the flanks of
describes the techniques for finding the best crossing attacking maneuver units by contaminating the terrain to
route. restrict movement.

Protection and Terrain

Terrain modifies CB weapons’ coverage. Hills disrupt
Decontamination the normal dispersion of chemical and biological agents.
If a unit is unable to avoid CB hazards, the individual
soldier and unit must take protective measures. Actions
that minimize equipment losses and limit the spread of Troops
contamination are discussed in this manual. Measures The physical condition of troops is very important.
taken to aid in protection are covered in FM 3-4. Tactical decisions must consider how troops will be
If a unit is unable to avoid contamination, then some affected. CB weapons and wearing MOPP 4 impacts
form of decon will be necessary. Decon reduces the psychologically and physiologically on troops.
immediate CB hazard. It may allow troops to reduce
their MOPP level and operate in a contamination-free Time
environment. Decon is discussed in FM 3-5. Tasks may take longer in a CB environment. Routine
tasks may be more difficult when troops are in MOPP
Tactical Considerations gear if they have not been trained to do them. Adding
If CB weapons are used, individual and collective CB requirements to conventional recon adds time to the
protective measures must be taken. Time-consuming mission. Decon operations are also time-consuming.
and manpower-intensive tasks such as CB reporting, and Anticipating the timing of CB attacks is important.
chemical recon, surveys, and decon may be necessary. Chemical and biological attacks are most likely to occur
during the night and early morning or evening hours.
Mission
CB contamination forces the commander to reconsider Training
how best to accomplish the mission with the available Commanders must understand the importance that
resources. The commander has five options. In order of training has on a soldier’s and unit’s ability to complete
preference, these are: the mission. When troops are well trained, they can
First, do the mission in a clean area. The commander survive and fight on a contaminated battlefield. Poorly
must decide whether the mission can be accomplished trained troops may not be able to recognize a CB attack,
while staying out of contaminated areas. and be less conditioned to wearing MOPP gear for
Second, do the mission in a contaminated area using a extended periods. Well-trained troops can do their jobs,
higher MOPP level, but take more time. while in an CB environment. They know tasks take
Third, do the mission in a contaminated area using a longer while wearing MOPP gear, but are able to adjust
higher MOPP level, and use more soldiers or equipment. their procedures and/or work rate accordingly.
Fourth, delay the mission until the contamination has
weathered.
Fifth, do the mission in the same amount of time with
the same number of soldiers, but take a greater risk by
using a MOPP level that does not provide maximum
protection.

Enemy
In addition to trying to determine what the enemy
plans to do, the commander also must determine how
and where the enemy is most likely to use CB weapons.
For example, if the enemy is attacking, expect biological
agents (pathogens) to be used as early as one to two
weeks prior to the attack. Expect nonpersistent chemical
agents and biological toxins to be used against front-line
units, and persistent agents and toxins to be used on

vii
FM 3-3

Chapter 1
Vulnerability Analysis

The focus of this field manual is Chemical and and the type and size of weapon likely to be used against
Biological (CB) Contamination Avoidance. Like most it. The commander then weighs various courses of action
concepts in the Army, contamination avoidance is a and determines which presents an acceptable risk to
process. This process involves— allow accomplishment of the mission. This whole
Assessing the threat facing friendly forces. process starts with the Intelligence Preparation of the
Identifying whether friendly units are a target. Battlefield (IPB) with an initial assessment of the CB
Understanding the field behavior of CB threat.
contamination.
Locating CB hazards on the battlefield. The IPB Process
By identifying and locating CB hazards on the The IPB process is a staff tool that helps identify and
battlefield, units will be able to either avoid the hazard answer the commander’s priority intelligence
or implement those protective procedures outlined in FM requirements (PIR), it’s part of the operational planning
3-4 to minimize the effects of the hazard on unit that is necessary for battle management.
performance. IPB is initiated and coordinated by the S2 and used to
However, before we begin the discussion of predict battlefield events and synchronize courses of
contamination avoidance, we must first discuss two action. IPB is designed to reduce the commander’s
critical, often overlooked, aspects of successful uncertainties concerning weather, enemy, and terrain for
operations on the contaminated battlefield. These two a specific geographic area in a graphic format. It enables
aspects are CB threat assessment and vulnerability the commander to see the battlefield: where friendly and
analysis. Both are described in this chapter. enemy forces can move, shoot, and communicate where
The CB threat now and in the future will be global critical areas lie; and where enemy forces (and his own)
from low to high intensity. Terrorists may be are most vulnerable. IPB guides the S2 in determining
encountered at any level of conflict. The proliferation of where and when to employ collection assets to detect or
CB capable nations in all contingency regions and the deny enemy activities. These assets, working
availability of toxic CB materials increase the liklihood collectively, fulfill intelligence requirements and answer
of US forces being direct or inadvertent targets of attack. the PIR. IPB is the key for preparing for battle. It
These attacks may range from limited use in terrorist analyzes the intelligence data base in detail to determine
actions to planned targeting in support of military the impact of enemy, weather, and terrain on the
operations. operation and presents this information graphically. It is
As Chapter 1 of FM 3-100 points out, CB a continuous process which supports planning and
proliferation is increasing. Deploying US forces must be execution for all operations. IPB consists of a systematic
capable of accurately assessing the CB threat imposed by five-function process involving—
the opposing force and be capable of addressing unit Evaluation of the battlefield (areas of operation and
vulnerability to attack. Chapter 2 in FM 3-100 describes influence).
in detail how CB agents may be used and how their use Terrain analysis.
may shape the battle. Weather amlysis.
When planning operations, commanders must consider Threat evaluation.
the potential effects of CB weapons on personnel and Threat integration.
equipment. In conventional operations, concentration of On the battlefield, units will have incomplete
forces increases the chance for success, but this same intelligence concerning enemy chemical and biological
concentration increases the effects of CB attacks and the capabilities and/or intentions. However, commanders,
likelihood of their occurrence. Consider the timing of must ensure that the IPB becomes an integrated process
force concentration to reduce the effects from a CB through which key members of the staff contribute. IPB
attack. is a process involving intelligence and operations
To assess a unit’s vulnerability to CB attack, the personnel. It must also be integrated with input from
commander determines how well protected the unit is chemical officers.

1-0
 FM 3-3

Chemical officers and NCOs, in coordination with the user-friendly manner, to the commander.
S2/3, must address CB warfare during all phases of the During battle management activities, the chemical
battle. This is accomplished only by direct participation staff advisor works with the S2 on the IPB. He
in the IPB process. Working with the S2, the chemical coordinates with the intelligence officer to analyze and
staff should— identify chemical targets based on threat, terrain, and the
Template potential chemical targets or areas of AO. Potential threat chemical targets could be key
contamination. terrain, choke points, command and control facilities,
Designate templated areas that effect the scheme of counterattack routes, mobility corridors, troop
maneuver as named areas of interest (NAI). concentrations and rear area assembly points.
Include NAIs into the collection plan and identify A CB vulnerability assessment constitutes an
indicators. important part of battlefield assessment and risk analysis
Include designated NAIs into the reconnaissance and and is a primary means through which the chemical staff
surveillance plan (R&S) and designate responsibility for advisor participates in the battlefield assessment process.
confirming or denying the template. In this assessment, the chemical officer must develop
Using the IPB process, the chemical officer/NCO information for integration into the various staff
provides the commander updates on the CB situation, as estimates. From the S2, the chemical officer/NCO
well as flame and smoke operations. obtains—
Based on the time periods of interest, the chemical Time period of interest.
staff will provide the battle commander with— Threat probable courses of action and intent.
Detailed information on enemy CB capabilities based Names areas of interest (NAIs) and target areas of
on the type of units and weapons the enemy has available interest (TAIs).
in the area of operations/area of influence (AO/AI) Summary of enemy activity, including any CB
during a selected time period. attacks, movements of CB equipment or material, or
How the enemy would employ chemical, biological, presence and level of training of threat forces, and
flame, or smoke to support his battle plan. indicators of enemy CB warfare comments such as
Areas of likely employment based on threat queuing up weather radar.
employment doctrine. Specific items of interest from the S2 would be:
Detailed analysis of terrain and weather in the unit’s Direction and speed of prevailing winds.
AO during each period of interest and how they could Average temperature and humidity and how these
impact on CB, flame, and smoke warfare. weather conditions may effect CB warfare agents,
MOPP guidance for each period of interest (such as, terrain, availability of water sources, transportation
minimum MOPP, automatic masking). assets (railways, airfields, road networks) available for
Alternative actions the commander can initiate prior shipment of CB munitions, and the availability and
to the phase time line in question so as to minimize location of industrial assets capable of producing and/or
degradation of forces. weaponizing CB warfare agents, availability of CB
Continuous monitoring of intelligence messages and agents and delivery systems, and location of stockpiles.
radio traffic for any CB related information which could From the Fire Support Officer (FSO), the chemical
be important to the unit’s mission. officer obtains information on casualty percentages from
It is important that the chemical officer/NCO be friendly and threat conventional munitions. Examples of
succinct during the commander’s briefing or have his information obtained might include—
information presented by the S3 during his portion of the Casualty percentages based on target size
briefing. Therefore, for input to be addressed, chemical Casualty percentages based on weapon systems
personnel must be a player in the IPB process. Although The chemical staff should also prepare a list of
it is developed under the direction of the S2, once information that is compiled from various sources (news
completed, the decision support template (DST) becomes bulletins, spot reports, intelligence summaries
an operational document and is briefed to the (INSUMs), and is general in nature. This information,
commander by the S3. As active participants in the IPB when viewed as a single event, may appear to be
process, the CB concerns will be included in the threat meaningless. However, when added to other pieces of
analysis and shown usually on the IPB template. It is information it may provide the key that connects the
through this participation that the chemical staff best information and present the best view of the enemy’s
serves the commander as special staff warfare experts, intent. Items of general information include, but is not
for the appropriate templates of IPB process will include limited to the following—
CB concerns and visually present them, in a Availability of CB defense equipment to enemy

1-1
FM 3-3

forces. If no protective equipment is available (such as white; serial 1 = green.). It does, however, require
MOPP, antidotes, masks) it may indicate that the enemy chemical personnel at brigade and division level to stay
does not intend on using CB weapons. abreast of the intelligence picture. The CB threat status
Amount of overhead cover or collective protection is outlined below—
shelters or systems; if enemy forces seek overhead cover a. Serial 0 (none).
or move into collective protection shelters, it may 1. The opposing force does not possess any CB
indicate that the enemy intends on using CB weapons. defense equipment, is not trained in CB defense or
Stated national policy or philosophy on the use of CB employment and do not possess the capability to employ
weapons. Has the enemy declared a no use, first use or CB warfare agents or systems. Further, the opposing
limited use only for retaliation in kind policy? Does the force is not expected to gain access to such weapons and
enemy consider the use of flame or smoke as CB agents? if they were able to gain these weapons, it is considered
Leadership—Is the enemy’s national or military highly unlikely that the weapons would be employed
leadership willing to use CB weapons on their own against US forces.
territory or expose their own populations to the hazards 2. Under this status a deploying force would not
generated from CB munitions? have to carry CB defense equipment nor decon assets.
If the enemy does not possess CB munitions, the However, protective masks should be carried. Chemical
capability to produce agents or expertise to employ personnel should concentrate efforts in smoke,
munitions; have attempts been made to gain this ability? herbicides, flame field expedients (FFE) and monitoring
Reports indicating the presence of advisors from other threat communication channels for CB threat indicators.
nations working with enemy forces, international trade b. Serial 1 (low).
agreements or shipments of agricultural equipment (such 1. The opposing force has an offensive CB
as sprayers, fertilizers, insecticides or raw chemicals) capability, has received training in defense and
may provide insight to the enemy’s intent. employment techniques, but there is no indication of the
Once information is gathered, it will provide input to use of CB weapons in the immediate future. This
the formulation of the CB Threat Status. indication may be based on whether CB munitions are
dispersed or deployed, or the stated objectives and
CB Threat Status intent of opposing forces.
US forces may not have to carry CB defense 2. Given this threat status, all personnel carry
equipment (such as MOPP) based on the initial threat their individual defense equipment or chemical defense
estimate. If the threat condition were to change and equipment stockpiles are identified and would be readily
indicators were present to suggest the possible use of CB available for deployment to the operational area if the
agents by the threat forces, CB defense equipment would threat status should increase. NBC reconnaissance
be deployed forward (such as division support area or to systems deploy to the operational area of interest to
the brigade support area). These stocks may be provide a monitoring capability. Chemical personnel
prepalletized for immediate deployment by aircraft to the continue to concentrate their efforts on NBC planning
affected unit if required. However, this decision must be and analysis for threat indicators.
made based on available aircraft or other transportation c. Serial 2 (medium).
1. The opposing force is equipped and trained in
systems. This could be done so that the forces would not CB defense and employment techniques. CB weapons
have to carry the mission oriented protective posture and employment systems are readily available. CB
(MOPP) ensemble in their field pack, ALICE (ruck weapons have been employed in other areas of the
sacks). theater. Continued employment of CB weapons is
The minimum CB threat status is set at division or considered probable in the immediate future. Indicators
separate brigade level and is a flexible system would be—
determined by the most current enemy situation, as CB munitions deployed to either field storage sites or
depicted by the continuously updated IPB process. This firing units.
allows local commanders to increase the threat status as Enemy troops wearing or carrying protective
conditions change in their area of operations. Threat equipment.
status governs the initial deployment of chemical assets CB recon elements observed with conventional recon
(such as equipment or units) and the positioning of those units.
assets on the battlefield or in the operational area. The CB decon elements moved forward.
CB threat status serial numbers are for planning purposes 2. Unit CB defense equipment should be either
in accordance with STANAG 2984. These numbers, pre-palletized and located forward for easy access or
however, may be substituted for a color code (serial 0 =

1-2
 FM 3-3

issued to the soldiers responsible for use within the unit. To assist in the formulation of the threat status, the
Individual soldiers should beat MOPP levels 1 or 2; chemical staff, (in conjunction with the S2) must analyze
MOPP 0, if MOPP gear is readily available. Erect all information received. A tool in this analysis is the
collective protection shelters if the tactical situation threat status matrix depicted in figure 1-1.
permits. Personnel and equipment should be kept under
cover as much as possible to protect them from
contamination. Chemical Downwind Messages (CDMs)
should be sent to subordinate units. Decontamination
assets, CB recon assets and smoke support should be
deployed as part of the force structure. Detection and
monitoring (such as CAM) equipment should be issued
to the operators. Unit should fill M11 and M13
Decontamination Apparatuses (DAP) and mount on
vehicles.
d. Serial 3 (high).
1. The opposing force possesses CB warfare
agents and delivery systems. CB defense equipment is
available and training status is considered at par or
better than that of the United States. CB weapons have
already been employed in the theater and attack is
considered imminent. Indicators are—
CB attack in progress but not in your area of
operation.
CB warnings/signals to enemy troops.
CB munitions delivered to firing units within range
of friendly forces.
Movement of surface-to-surface missiles to a launch Use X’s to mark applicable boxes or degree of threat.
site. Total columns and use serial number with largest
2. US forces should deploy with CB defense number of X‘s as the current threat status.
equipment in the unit load. Soldiers should either carry More than one matrix may be necessary to determine
the overgarments in their rack sacks, CB bag, or wear the threat status for chemical and biological attack.
the overgarments. This will depend on the CB threat to To use the matrix, place an “x” in the appropriate
the airfield or port on which they land. Soldiers should block. Add each column; and whichever column has the
change protective mask filters prior to deployment. most “x’s” provides a means to identify what threat
Decontamination and CB recon assets should be task status serial number could be used to identify an
organized and moved forward. Contingency stocks of indication of the enemy force intent. If an overall threat
CB defense equipment may be moved forward to the status cannot be determined due to an informational
battalion trains. CDMs are initiated and place collective shortfall, collection assets should be reallocated or
protection systems into a state of readiness including positioned to gain the needed information.
those systems in combat vehicles. Once the threat status estimate has been assessed the
This threat status can be used as a single number chemical staff must analyze the protection level required
representing both C and B or as individual C and B for friendly forces. This is accomplished by using MOPP
statuses. It is possible to have a C status of three and a B analysis—key factors include analyzing mission,
status of zero. This threat status provides the commander environment, and soldier factors—as discussed in FM
with guidance for deployment and operational purposes. 3-4 and the factors listed below.
It allows the commander to tailor chemical units to fit Understanding the mission and commander’s intent
any situation. for friendly forces.
Threat status can change rapidly. Although a C status Capabilities and level of training of friendly forces.
of zero may exist during deployment, the opposing force MOPP analysis and work degradation factors
may seize industrial chemicals or obtain warfare agents contained in FM 3-4.
from a sponsoring nation. Therefore, the ground Availability of chemical defense equipment and
commander must be capable of upgrading the CB decontamination assets. In this regard, information may
defense posture quickly. be obtained from the S2 or G5.

1-3
FM 3-3

Other factors include— degradation factors. The commander must achieve a

Location and availability of desalination plants (for balance between reducing the number of casualties from
arid areas). the attack, avoiding heat casualties, and reducing
Location of civilian chemical manufacturing and individual performance degradation.
storage facilities. Chemicals at these facilities may be Analyzing chemical vulnerability is difficult.
used, through civilian contract, for supplementary decon Casualties can result from on-target attacks, off-target
supplies. Further, chemicals or hazardous materials attacks, downwind hazards, and residual liquid
stored in these facilities may produce areas of contamination. Table 1-1 is a guide to help evaluate
contamination if storage containers leak (either chemical hazard vulnerability. The chart is safesided and
intentional or unintentional). To assess these hazards and assumes a direct attack on troops in MOPP 1 or 2. Use
how such a leak may impact on operations refer to the chart in the same manner as the radius of
Department of Transportation (DOT) Regulation 5300.3, vulnerability tables for nuclear weapons. Remember that
Emergency Response Guidebook or the Department of chemical weapons are delivered as battery or battalion
Defense (DOD) Regulation 4145.19-R-1, Hazardous volleys and not single munitions as with nuclear
Materials Storage and Handling criteria. weapons.
Availability of civilian contracted labor and water If troops are wearing MOPP 4 at the time of the
transport for decon operations. attack, reduce these percentages to a negligible level.
For urban areas, location of car washes. These car The figures in Table 1-1 are for employment under
washes may be used in lieu of hasty decon stations. optimum attack conditions. Optimum conditions for
Obtain data on local fire hydrants (such as location, employment of chemical weapons is generally
hookups). Hydrants may be used to provide water for considered to be stable or neutral temperature gradients
decon operations. and light winds less than 10 kmph. If troops are in some
The chemical staff must properly prepare the threat form of shelter such as a building, the percentages
status and identify the protection level required for initially will be less. The percentages will also be less if
friendly forces to withstand an CB attack. This high winds exist or during hot temperatures.
information is vital to the commander and for the Table 1-2 shows the effects of temperature change on
successful accomplishment of the mission. The an agent’s persistency. Cooler conditions increase the
commander may be required to reallocate or position persistency of chemical agents. As a general rule,
units on the battlefield to reduce vulnerability to an persistency triples as contamination levels increase from
attack. moderate to heavy. Moderate contamination is defined as
one gram of agent per square meter. This concentration
Chemical Vulnerability can be further defined as the amount of vapor
contamination that would cause one-to-four bar display
Analysis on the Chemical Agent Monitor (CAM). Heavy
There is no difference in vulnerability analysis contamination is defined as ten grams or more of agent
procedures between chemical agents and biological per square meter. Heavy concentrations would cause
toxins. The following applies to both. five-to-eight bars on the CAM. Moderate and heavy
Unit vulnerability to a CB attack depends primarily on
the protection the unit has taken and the type and amount
of chemical agents delivered. For nonpersistent agents,
the risk of casualties to units in MOPP 4 is negligible.
This is also true for persistent agents if appropriate and
timely decon measures are taken. Persistency, as defined
in FM 3-9, is an expression of the duration of
effectiveness of a chemical agent. This is dependent on
physical and chemical properties of the agent, weather,
methods of dissemination, and conditions of terrain.
Nonpersistent agents generally include: choking agents,
blood agents, and G-series nerve agents. Persistent
agents generally include: blister agents, VX, GD and
thickened nerve agents. If personnel are forced to stay in
MOPP gear, performance is degraded and heat casualties
may occur. Refer to FM 3-4 for detailed information on

1-4
 FM 3-3,C1

contamination detected on M9 Chemical Agent Detection

Paper is depicted in Figures 1-2 and 1-3.
Chemical agent persistency data given for surface
winds of 10 kmph. For other surfaces use the following
multiplication factors for the times given alkyd paint =
1.3, bare soil = 4.0. Agent HL is not shown. To
approximate
0 0 0
HL use GD persistency times.
O
To convert
C to F ; F = 1.8C+32. To convert F to C°; C = (F
- 32) ÷ 1.8. All concentrations of contamination is
considered to be heavy (10 grams square meter). One
week is considered to be 168 hours. One month (30
days) is equal to 720 hours. One year (365 days) is equal
to 8640 hours.
The information presented in tables 1-1 and 1-2
provide a quick planning guide for chemical agent
persistency. For a more detailed discussion of chemical
agent persistency, see FM 3-4, Chapter 3.

1-5
FM 3-3

Avoid detection.
Biological Vulnerability Provide warning.
Analysis Maintain discipline.
The effects of biological agents are very Seek protection.
unpredictable, unlike nuclear and chemical weapons. Disperse.
Biological agents are effective in low concentrations, and Remain mobile.
personnel outside the target area may be affected. Cover supplies and equipment.
Vulnerability reduction methods include Prevent spread of contamination.
Employ a good immunization program before Follow unit SOPs.
deployment Camouflage.
Ensure personnel wear MOPP gear. Plan Ahead
Eat food only from protective wrappers and sealed Tasks may become more complicated in a CB
containers. environment due to the degradation of protective
Drink only purified water. equipment. Again, FM 3-4 contains tables to help
Report and seek treatment for illness promptly. commanders estimate how long it takes to accomplish
Ensure personnel practise good personnel hygiene. missions in an CB environment. Commanders must take
For a more detailed discussion on biological warfare time to carefully think out Courses Of Action (COA’s)
agents, their properties and effects, refer to Chapter 4. and allow for the additional time requirement. This is
commonly referred to as wargaming. A bad decision
Vulnerability Reduction could cause the unit to become needlessly contaminated
Active measures prevent the enemy from using CB or suffer casualties. Use the CB threat status for planning
weapons; passive measures increase survivability. and stocking CB defense/equipment. Units must prepare
Individual and unit collective measures are only to continue the mission after an CB attack. Following an
discussed briefly here. See FM 3-4 for detailed enemy CB strike, commanders must quickly assess the
information. damage and reconstitute lost or weakened units.
Avoid Detection
Active Measures Avoiding detection is the best way to prevent CB
Active measures are those measures taken to find and attacks. Do this by employing good operational security
destroy either the munitions or the delivery systems. (OPSEC) measures. These include camouflage, light
Destruction of delivery systems and munitions is the best discipline, and especially, signal security. Both active
method of reducing the chances of being attacked. and passive measures must be used to prevent the enemy
The destruction of stockpiles of CB munitions and from gaining target information. Use defensive
production facilities is usually beyond the capabilities of electronic warfare (ECM and ECCM) to reduce the
lower level commanders. Echelons above corps have the chances for identification and location. Once a CB attack
responsibility and sufficient assets for finding and is detected or suspected, commanders should consult
destroying these targets. higher headquarters for guidance if unit displacement is
Corps and divisions do not have the capability to necessary.
locate and destroy stockpiles or production facilities; but
they do have the capability to find and destroy delivery Provide Warning
systems. Recon flights, counterbattery radar, and other If the unit is unable to avoid CB attacks, early
intelligence collection assets are used to find delivery warning of battlefield hazards is very important. The
systems such as long-range cannons and missile systems. NBC Warning and Reporting System (NBCWRS)
notifies units that adjacent units have been attacked or
that a downwind hazard is present. Automatic alarms,
Passive Measures such as the M8A1, positioned upwind to detect the
It is not possible to destroy all threat CB munitions arrival of an agent cloud may warn of probable attacks.
and/or delivery systems; units must always take When no NBCWRS warning is received, these alarms let
precautions to avoid being targeted or to reduce the the unit adjust MOPP levels to meet the threat. Troops
effects of an attack if one does occur. These are passive must be able to identify CB attacks and take appropriate
measures. All units must use passive measures as part of actions. CB recon teams using the NBC Reconnaissance
normal operations to reduce the effects of operating System (NBCRS) alert moving units before they enter
under CB conditions. These measures include— contaminated areas.
Plan ahead.

1-6
 FM 3-3

Maintain Discipline Cover Supplies and Equipment

The unit must maintain discipline and confidence in Store supplies and equipment under cover to prevent
their ability to survive and operate if they are to contamination. Buildings offer excellent protection. NBC
overcome the shock of an CB attack and continue the protective covers (NBC-PC), tarpaulins, pallets, packing
mission. Troops must be conditioned physically and materials, dunnage, and plastic (sheets, bags, and rolls)
mentally to wear and function in MOPP gear for all can be used. Field expedient covers, especially
extended periods of time. Commanders must be able to canvas and cardboard, provide protection from liquid
rely on their troops to wear MOPP gear when required agents for a short period of time. Contamination seeps
and to remain in MOPP until told to reduce the level. through all such covers, however, the NBC-PC will
Again, plan ahead. Develop MOPP acclimation plans provide protection for up to 24 hours. Units must replace
within the unit. Use these plans whenever possible the covers as soon as possible after heavy contamination.
during unit training. Use the information contained in Canvas will keep out more than 95 percent of liquid
FM 3-4 to assist in developing a unit acclimation plan. contamination if it is removed within 60 minutes after
the attack. Although these covers may provide protection
Seek Protection against liquid agents, a contact hazard will remain until
Natural terrain may provide shelter from the effects of the agent on the ground and the protective cover has
CB weapons. However, ditches, ravines, and natural weathered.
depressions allow accumulation of chemical agents.
Heavy forests and jungles protect against liquid chemical Limit Exposure
agents, but vapor hazards will increase. All plans should include postattack procedures for
Foxholes with overhead cover and shelters offer good limiting exposure to CB hazards. The longer a person is
protection against the explosive and liquid effects of CB exposed to chemical contamination, the greater the
weapons. However, any overhead cover such as tents, chance of becoming a casualty. Only personnel required
tarpaulins, and ponchos offer at least some protection to accomplish a mission are sent into a contaminated
from liquid chemical agents. Use NBC protective covers area.
(NBC-PC) whenever possible. Limit exposure with time. By waiting to enter a
contaminated area, the contamination level will usually
Disperse be reduced and with it the chance of exposure. Exposure
Combat service support (CSS) installations and troops can also be accidental. Personnel may not know that
in compact assembly areas are vulnerable to CB equipment is contaminated. Usually, this can be
weapons. Commanders must determine how much prevented by always marking contaminated equipment.
dispersion is needed. Dispersion must reduce But there are places where CB contamination hazards
vulnerability but not hinder operations or prevent the can accumulate such as in air filters. All engines have air
unit from concentrating when necessary. Supplies filters which trap CB contaminants. These contaminants
especially food, POL, and ammunition must be dispersed accumulate. So even if the hazard area is small, it can be
so they will not all be destroyed at once. The more deadly. Persons working around equipment should be
dispersed a unit is, the longer it will take to do even aware of hidden hazards. Always dispose of
routine tasks. The degree of acceptable dispersion contaminated collectors, such as air filters, as
depends upon mission, enemy, terrain, troops, and time contaminated waste.
available (METT-T).
Prevent Spread of Contamination
Remain Mobile Limit the number of personnel and amount of
Tactical mobility gives the commander the best chance equipment in the contaminated area. Confine CB
for avoidance. Constant movement prevents the enemy contamination to a small area as possible. This begins
from pinpointing locations and accurately employing CB with monitoring to determine the amount and extent of
weapons. However, the battlefield will be a difficult contamination. Units moving from a contaminated area
place in which to maneuver. Contaminated areas, tree into a clean area should decontaminate at or near the
blowdown, urban rubble, fires, flooding, fallout, and edge of contamination. Mark all contaminated areas and
craters are obstacles that will have to be dealt with. CB report them to higher headquarters and adjacent units to
recon teams and the serving S2/G2 can provide useful prevent them from entering the contaminated area
information. The best source of information on mobility unknowingly.
routes, however, is the Movement Control Center If the situation permits, contaminated material can be
(MCC). left and allowed to weather. If the equipment is mission
essential, it must be decontaminated or brought back to

1-7
FM 3-3

the rear for decontamination. present.

Decontaminate as far forward as possible. If Monitor and decontaminate transport vehicles before
contaminated material must be moved, the unit runs the transporting noncontaminated material.
risk of transferring contamination to road networks or Ensure transport crews wear appropriate MOPP
ground surface which is proportional to the amount of gear.
contamination on the material, location of the When contaminated material or waste material must
contamination, type of contamination, and type of be destroyed, either burn or bury the contaminated
surface on which the contamination is present. When material. Agents destroyed by burning produce a vapor
moving this equipment: hazard. So if material is burned, send a warning to
Notify the MCC of contaminated vehicles or downwind units. Burial is effective for all types of
contaminated routes. contamination. Mark and avoid the area where
Use as few transport vehicles as possible. contaminated waste is buried. Procedures for marking
Use one route (especially around congested areas). contaminated waste burial sites is outlined in FM 3-5.
Monitor the route periodically for contamination. This consists of submitting an NBC-5 Chemical Report
Cover the material to keep contamination from being outlining the contaminated waste burial site. However,
blown onto the road. (Weigh the risk of ground this report must be sent by the NBCC so that line item
contamination with additional burden of Alpha, (strike serial number) may be assigned. The unit,
decontamination/disposing of potentially contaminated therefore, that closes the decontamination site, must
covering material). notify the NBCC.
Warn personnel downwind if a vapor hazard is

1-8
 FM 3-3, C1

Chapter 2
NBC Warning and Reporting System
(NBCWRS)
The primary means of warning units of an actual or
predicted CB hazard is the NBC Warning and Reporting
system (NBCWRS). It is a key in limiting the effects of
CB attacks. The NBCWRS allows units to determine
required protective measures and plan operations. Units
take action depending on the mission and type of hazard
present. If the mission allows, affected units alter plans to
avoid the hazard. Otherwise, the units upgrade protective
measures and occupy or cross the hazard area

Standard NBC Reports

The NBCWRS consists of six reports. Each is
standardized by ATP 45/STANAG 2103 Change 4, dated
Jan 89 and the United States Message Text Format
(USMTF). The U.S., NATO and British, Canadian, and
Australian use the same message formats. The six
standard reports are—
NBC 1-Initial report, used for passing basic data
compiled at unit level.
NBC 2-Report used for passing evaluated data.
NBC 3-Report used for immediate warning of
predicted contamination and hazard areas.
NBC 4-Report used for passing monitoring and
survey results.
NBC 5-Report used for passing information on areas
of actual contamination.
NBC 6-Report used for passing detailed information
on chemical or biological attacks.
The reports use standard formats to shorten the
message being passed. The warning and reporting system
is based on a code letter system. The meaning of each
letter used to transmit an NBC message is described in
Table 2-1 and GTA 3-6-5. The following paragraphs
described each report. Specific instructions for acquiring
the information and sending the report are discussed later
in this chapter. Refer to Chapter 4 for specific use of the
NBCWRS for biological attacks.

NBC 1 Report
The NBC 1 Report is the most widely used report. The
observing unit uses this report to provide CB attack data.
All units must be familiar with the NBC 1 Report format
and its information. The unit must prepare this report
quickly and accurately and send it to the next higher
headquarters.
Battalion and higher elements decide which NBC 1

2-1
FM 3-3, C1

Precedence of the NBC 1 Report depends on whether or

not it is an initial report. The initial use report is FLASH
precedence, all others are IMMEDIATE precedence.
Individuals identified by unit SOP submit observations
to the unit NBC defense team at company/battery or troop
level. They need not use the NBC 1 Report format or
individual line items of the NBCWRS to pass this data to
the NBC Defense Team. (This report is generally in the
form of a SPOT report or SALUTE report). The unit
NBC defense team normally consists of the unit chemical
NCO (54B20) or an NBC NCO that has been school
trained at an area NBC defense two week school, an
officer and an enlisted soldier (Specialist 4 or above) that
has attended the same two week school. These soldiers
will have the expertise at unit level of advising the
commander on NBC defense matters and formating NBC
reports.
Normally, the unit NBC defense team formats NBC 1
Reports. This ensures the content of the report is known
to the commander or his or her representative. It also
ensures that the report is in the proper format and is as
correct as possible.
All data is sent in a single, complete NBC 1 Report.
Do not divide data into two parts to create a subsequent
report. NBC 1 Reports are not attack notifications, they
simply pass data. Separate procedures must be developed
for attack notification and are beyond the scope of this
manual. Attack notification may take the form of a
SALUTE, SPOT or SITREP Report and should be
addressed in detail in unit SOPs.

Initial Use Report

The first time a CB weapon is used against US forces
the observing unit will send the NBC 1 Report with a
FLASH precedence. Each intermediate headquarters will
forward the report with a FLASH precedence (or
Reports to forward to the next higher headquarters. If IMMEDIATE precedence if a previous NBC 1 Report
several reports are received on the same biological or has been forwarded). If the report is of a second attack
chemical attack, then a consolidated NBC 1 Report is within the division, use IMMEDIATE.
forwarded. This reduces the number of reports to a The observer determines the date-time group of the
manageable level. If the NBC 1 Report, however, is attack, location of the attack, means of delivery, type of
based on a chemical agent alarm going off and there is no burst (air or ground), and if possible, type of agent. The
other indication of an attack (such as in-coming artillery NBC defense team then formats the NBC 1 Report and
rounds) the battalion chemical staff should inform higher forwards it to the next higher headquarters. All units
headquarters, but request that the sending unit verifies the prepare and forward NBC 1 Report.
attack with two or more sampler/detector tickets from a Battalion and higher headquarters screen NBC 1
M256 Chemical Agent Detector Kit. The attack should be Reports and decide which report(s) to forward. If the
verified at this level before the NBC 1 Report is sent to headquarters receives several reports pertaining to the
higher headquarters. This helps to eliminate a false report same attack, it forwards a consolidated NBC 1 Report
from causing an entire brigade task force or division to go instead of separate reports. All reports must include line
into Mission Oriented Protective Posture (MOPP). NBC items Bravo (position of observer), Delta (date/time
1 Reports are not routinely) passed to corps or higher group), Hotel (type of burst), and either Charlie
NBC centers (NBCC) except for the initial use report. (direction of attack) or Foxtrot (location of attack). Use

2-2
 FM 3-3, C1

other line items if the information is known. If the unit is that chemical agent alarms are placed far enough upwind
capable of providing local weather information as listed in to provide adequate warning. The NBC 3 Chemical
line items Yankee (downwind direction of hazard and Report is re-evaluated every two hours. The hazard
wind speed) and Zulu Alpha (significant weather prediction could change significantly. Units currently
phenomena) this information should be included in the affected and those previously affected must be notified
report. that they are in (or are no longer in) the hazard area. Line
items Alfa (strike serial number), Delta (date/time
NBC 2 Report group), Foxtrot (location), Hotel (type), Papa Alfa
(predicted hazard area), Papa Bravo (duration of hazard)
The NBC 2 Report is based on one or more NBC 1 (if ground contamination is present), Yankee (downwind
Reports. It is used to pass evaluated data to higher, hazard and speed), and Zulu Alfa (weather) are used for a
subordinate, and adjacent units. Division NBCC is chemical hazard prediction. In order that a recipient of an
usually the lowest level that prepares NBC 2 Reports. NBC 3 Chemical Report be able to plot the downwind
Brigade and battalion NBC personnel may prepare the hazard area easily and quickly, Line Zulu Bravo may
NBC 2 Report if they have sufficient data. However, contain the following information-type and case of
these units will not assign a strike serial number. attack, or the downwind hazard distance (DHD). use
Units use the NBC 2 as a factor in determining whether other line items if the information is known.
to adjust MOPP levels, and to assist in planning future
operations. Line items Alfa (strike serial number), Delta
(date/time group), Foxtrot (location), Golf (means of NBC 4 Report
delivery), and Hotel (type of burst) are always contained Actual contamination is reported using an NBC 4
in the NBC 2 Chemical or Biological Report. Items Report. Separate NBC 4 Reports are plotted on the
Yankee (downwind direction speed), Zulu Alfa (weather), tactical map to show where the hazard exists. If
and Zulu Bravo (remarks) should be included in the monitoring information is incomplete, a survey may be
chemical or biological report. Line item Zulu Bravo directed. Line items Hotel (type of attack), Quebec
(remarks) should include the type and case of attack, if (location of sample), and Sierra (date/time of
known. Use other line items if the information is known. contamination was detected) are reported for a chemical
hazard. These items are used as often as necessary to
NBC 3 Report complete the report. Other items may be included if
Division NBCC uses the NBC 2 Reports and the available and necessary to complete the report. A
current wind information to predict the downwind hazard contamination overlay is sent to all units by computer
area. This is sent as an NBC 3 Report. It is sent to all data base update, electrical facsimile, messenger, liaison
officer, and the NBC 5 Report.
units that could be affected by the hazard. Each unit plots
the NBC 3 Report and determines which of its
subordinate units are affected and warns those units
accordingly. NBC 5 Report
The NBC 3 Report is a prediction of a downwind The NBC 5 Report is prepared from the contamination
hazard area. This prediction is safesided to ensure that a plot. This report is last in order because it consists of a
militarily significant hazard will not exist outside of the series of grid coordinates. Often this message must be
predicted hazard area. Commanders should use the report sent on FM radio nets. This requires lengthy
as battlefield intelligence when considering courses of transmission. The recipient is required to plot each
action. When a unit is in a downwind hazard area, the coordinate and redraw the plot. Complete details can
commander must decide whether to stay or move. This follow later on the facsimile or messenger-delivered plot.
decision is based on the mission, and higher headquarters For CB contamination, line items Alfa (strike serial
guidance. As the Automated Nuclear, Biological, and number), Delta (date/time group), Hotel (type of burst),
Chemical Information System (ANBACIS) is improved, Sierra (date/time of sample), Tango (date/time of latest
the commander will be able to view the modeled hazard survey), and X-Ray (area of actual contamination) are
area on a computer screen instead of basing his decision reported.
On the safe-sided STANAG plots. This will provide a With the exception of line item Alfa, when a user has
more realistic depiction of the hazard area. ANBACIS is previously received data through other NBC reports, the
addressed in more detail later in this chapter. data need not be repeated on the NBC 5.
Units within the chemical downwind hazard area must This message may be sent before or after a
adjust their MOPP level, if necessary, They must ensure contamination plot has been received. The NBC 5 Report

2-3
FM 3-3

is also used to report the closure of a decontamination hazards will be. This prediction (NBC 3 Report) is only
site. The NBC 5 Report should include coordinates for an estimation of the hazard area. Feedback is needed
the site and sump so as to notify other units of the from units to determine exactly where the contamination
contamination area. is located.
This feedback comes from monitoring, survey and
NBC 6 Report recon (NBC 4 Reports). Monitoring and recon operations
give the
This report summarizes information concerning a Initial monitoring initial location of CB hazards to the NBCC.
chemical or biological attack(s) and is prepared at forwarded through intelligence and recon reports are generally
battalion level, but only if requested by higher This information may also be channels sent to
to the NBCC.
the NBCC by
headquarters. It is used as an intelligence tool to help ANBACIS. ANBACIS is the Automated NBC
determine enemy future intentions. The NBC 6 Report is
Information System and is described later in this
submitted to higher headquarters. It is written in narrative The NBCC plots the information on the situation map. If chapter.
form, with as much detail as possible under each line more information is needed, the NBCC recommends a
item. The NBC 6 Report may also be used to warn and unit (picked because of its location and/or capability) to
report suspected biological attacks. Information collect and forward the necessary data. This unit may be
concerning this use of an NBC 6 Report is described in
detail in Chapter 4. an organic unit NBC defense team or an NBC
reconnaissance platoon from the divisional chemical
defense company. Special operations forces will depend
Managing the NBC on special forces operational detachments (SFOD) with
attached LB teams, special forces group (SFG) chemical
Warning and Reporting detachments, or organic unit NBC defense teams. The
System reconnaissance platoon may be tasked organized to
Managing the NBCWRS is crucial for the success of a support a maneuver brigade in NBC reconnaissance
command. To be useful, CB information must be collection efforts.
collected, reported, and evaluated. Once evaluated, it can Collecting CB information is a joint effort between
be used as battlefield intelligence. Obtaining and units and the NBCC. The unit does the actual collecting
converting CB information into usable CB intelligence of information. The NBCC plans for and directs the
does not just happen. The volume of information that collection effort. The division FSOP/OPORD/OPLAN
needs to be collected and reported could easily disrupt should describe who collects and forwards CB
both communications and tactical operations if not information for evaluation. More detailed information
properly managed. This section describes what concerning this collection effort is addressed in Chapter
information is available and how that information gets to or in FM 3-19.
the person or unit needing it.
Collecting CB Information
Evaluating
The first step in managing the NBCWRS is to CB Information
determine what information is available and who is The CB data must be collected and evaluated by the
available to collect it. Two types of data must be NBCC and used as battlefield intelligence. Units and
collected. Observer data provides information that an CB intermediate headquarters use the raw data to develop CB
attack has occurred. Monitoring, survey, and recon data intelligence for their own use until detailed results are
provide information on where the hazard is located. available from the NBCC.
Observer Data Unit Procedures
Every unit is responsible for observing and recording Unit procedures for determining the location of
CB attacks. But every unit does not automatically forward contamination are simplified and less accurate than
NBC 1 Reports. Any unit aware of a chemical or NBCC procedures. Emphasis is on speed rather than
biological attack promptly prepares and forwards an NBC accuracy.
1 Chemical or Biological Report. With-exception of designated observer reporting units,
intermediate headquarters (such as battalion and brigade)
Monitoring, Surveyr and Reconnaissance consolidate and screen NBC reports to reduce the number
Data sent to the NBCC.
NBC 1 Reports allow the NBCC to predict where the NBCC Procedures

2-4
 FM 3-3

Procedures used by the NBCC are more detailed and are passed on the intelligence net rather than the
complex than those at unit level. command net. At battalion level and lower there is
NBC 2, NBC 3, and NBC 5 Reports from division generally only one FM net available. This net is required
NBCC supersede those done by subordinate units. to communicate command information. Therefore, NBC
Reports should be formatted ahead of time and be as short
Transmitting and concise as possible. In this case, wire
communications are best. Support units use Admin-Log
CB Information nets. However, these units need to also inform the
Procedures used to transmit CB information to and brigade TOC or division TOC when operating in that
from the NBCC are an important part of the CB units Area of Operations (AO). Wire communications are
information system. Figure 2-1 shows the direction that excellent, if available. There are numerous methods to
various NBC reports travel. Usually the flow is through communicate CB information. One of which is
the chain of command—from company to battalion to ANBACIS, which accesses information from the
brigade to division. There are exceptions to this— maneuver control system (MCS). The NBCC should
The NBCC may request data such as survey evaluate all possible methods and select those that best
information. The unit doing the survey may report suit the purpose. Again, this information should be
directly back to division. The monitoring unit must also contained in the unit SOP or current operations order.
send an information copy back to the parent unit for Each unit and command element has a specific function
2
command and control (C ) and for reordering CB in a CB environment. This function is in addition to
defensive stocks. normal combat functions. The exception to this is the
Attached or OPCON units may have no direct contact NBCC whose primary function is NBC operations. The
with a parent unit. In these cases the headquarters to preceding pages described procedures and requirements
which they are OPCON passes CB information. for collecting, evaluating, and transmitting CB
Units that operate independently (such as military information. This section describes responsibilities at
police or engineers) will report through the controlling each command level and is intended to be only a guide.
headquarters. Actions at Unit Level
The method of transmitting information depends on the
tactical situation and mission of the unit. Methods are Unit level collection, processing, and analysis
specified in FSOP/OPLAN/OPORD and unit SOP. At techniques are designed for rapid evaluation of CB data.
brigade and higher headquarters, NBC Reports usually The results are not as accurate as those obtained by the
NBCC, but they are sufficient for planning until replaced
by data from the NBCC. Although analysis techniques are
similar for company, battalion, and brigade, each has
specific responsibilities for collecting and processing CB
information. The responsibilities are discussed here.
Analysis techniques are explained in the appropriate
chapter.
The major portion of CB information is collected and
reported by company/ battery/troop-level units. These
units must be trained and equipped to—
Report CB attack data using the NBC Warning and
Reporting System.
Monitor for chemical agents.
Plot simplified downwind hazards.
Identify toxic chemical agents.
Collect and forward soil and water samples.
Conduct chemical and biological
surveys/reconnaissance.
Organization and training of personnel to perform these
tasks will be in accordance with AR 350-42.
Battalion Level
The battalion monitors the information gathering of

2-5
FM 3-3

subordinate units. Battalion chemical personnel ensure Defense training status.

each subordinate unit is trained. Battalion personnel also Types of defensive equipment used by soldiers.
are trained to—
Consolidate and forward NBC reports. Chemical Attack Warning
Estimate effects of CB hazards.
Disseminate information on CB activities. (CHEMWARN)
Coordinate unit CB recon elements with and through The CHEMWARN message is very similar to the NBC
the battalion S2/S3 sections and the chemical company 3 Chemical Report. The meaning and use of each line
platoon leader tasked to support the battalion. item are shown in Table 2-2. Figure 2-2, on page 2-7,
Coordinate with Brigade to obtain additional smoke or shows some examples of CHEMWARN messages.
decon assets, if required. Two hazard areas exist for a chemical attack—the
Advise the commander on how to employ CB assets. attack area and the downwind hazard area. Under normal
Plan and supervise decentralized CB surveys. conditions, a chemical attack will not be carried out if
Maintain a CB situation overlay. friendly troops are within the attack area. Personnel in the
downwind hazard area may don MOPP gear.
Brigade/Task Force Level
The chemical personnel at brigade must perform the
same functions as battalion chemical personnel. Brigade
personnel also must—
Coordinate with all attached NBC units.
Coordinate with other staff sections and advise them
on CB matters.
Plan and supervise decentralized CB surveys.
Collect information from and assist CB personnel
within the task force.
NBCC Level
NBCC techniques involve more complicated
procedures and are based upon the comparison of data
from many sources. Much of this data is not available to
a single unit. In addition to performing dettailed analysis,
the NBCC also —
Receives, collates, evaluates, and disseminates reports
of enemy CB attacks.
Prepares and disseminates wind messages.
Estimates the effects of enemy and friendly chemical
and enemy biological attacks, including hazard
predictions.
Coordinates recon and survey activities with higher,
lower, and adjacent units.
Maintains a CB situation map.
Provides advise to G2 on CB intelligence matters.
Provides technical assistance to all staff levels.
Coordinates with other staff sections and advises those
staff sections on CB matters.
Provides technical assistance in the interrogation of
POWs on CB matters. This technical assistance is Automated Nuclear,
generally in the form of providing the interrogator with a Biological, and Chemical
list of questions to ask the prisoner. The questions may
include— Information System
Employment tactics.
CB munitions. (ANBACIS)
Types of agents available. ANBACIS is a software information system which will
support the chemical staff officer and NCOs as well as

2-6
 FM 3-3

endurance. By relieving the chemical staff from

repetitious and intensive calculational tasks, the soldiers
will be able to apply their skills more effectively at
assisting the commanders and other staff members. By
not expending time and effort on those tasks, they will be
more mentally alert and less subject to making mistakes.
Calculate the NBC 3 and 5 Reports from the NBC 1
and 4 Reports and then display them on the electronic
map (E-MAP) with the units, boundaries, and other map
information. This overlay information will be available to
the other terminals for use in their planning and
operations.
Communication capability. ANBACIS will not have
any inherent communications capability. It is designed to
use the communications from the maneuver control
system or army common hardware and software
packages.
Found at all force level staff sections (such as
battalion, brigade, division), and chemical units down to
squad level.
Handle all NBC Reports 1 through 5. It utilizes many
checks and constraints to prevent false information from
chemical units (squad to brigade) with the being used. It will automatically look-up and utilize the
communication, recordkeeping, and calculation of NBC correct weather information contained in the database. In
warning and reports, tactical decision aids, and databases addition, it will create flame field expedient plans, smoke
essential to accomplish their tasks. One module is the plans, and NBC 4 Reports from monitor and survey
NBCWRS which is an automation of the manual data reports.
processing as described in this manual. ANBACIS was Operated by the normal Chemical Corps staff or unit
designed to operate on the Army common hardware and representative, all enlisted and officers.
also to operate in the stand alone mode on any IBM ANBACIS is designed to work best in the maneuver
compatible computer. ANBACIS is user friendly with control system organization. A stand-alone capability will
drop down windows and is operated by chemical staff be maintained to work on most IBM compatible
personnel. computers. This will allow continuity of operations and
It can receive any number of NBC 1 Reports and create allow work to be accomplished when separated from the
the correct number of NBC 2 Reports. It will then MCS environment. When the operator returns to the
convert the NBC 2 Reports to NBC 3 Reports utilizing MCS, he can load the plans into the MCS-ANBACIS
the correct weather information that has been previously using a diskette.
received electronically from the staff weather officer. It It has other modules including smoke plan creation and
will take the basic wind report and create the Chemical flame field expedients (FFE), and others.
Downwind Report in seconds. For additional information on ANBACIS, refer to the
ANBACIS supports battle management by— ANBACIS User’s Guide.
Reducing human error on assisting in soldier

2-7
FM 3-3

Chapter 3
Chemical Agents
Avoidance of chemical agents requires a complete Avoid areas heavily splashed with liquid
understanding of physical characteristics, employment, contamination which may be persistent for several days
and weather and terrain conditions. Units can then (depending on weather and type of agent). See FM 3-6
estimate when and where specific type of chemical agents for more details.
will be used, where the hazards are, and how best to Cover personnel, equipment, and supplies whenever
avoid them. possible.
Threat forces are equipped, structured, and trained to Monitor for the chemical agent for 2 to 10 days
conduct chemical operations. We expect them to use (depending on weather and type of agent). See FM 3-6
chemical agents as part of their conventional fighting for more details.
capability because so much of their training revolves Concentrate on finding clean areas and routes (recon
around the use of such agents. units).
The basic threat principle is to use chemical agents on Cross contaminated areas in MOPP 4.
unprotected troops to create casualties. Against protected Mark contaminated areas.
troops, the primary purpose is to make the use of Avoid contact with unknown liquids.
equipment, terrain, and operations more difficult. The use
of chemical weapons by the threat forces initially may Nonpersistent
require a decision at the same level as nuclear weapons. Threat forces currently stockpile blood agents, choking
But they most likely will be used more freely once the agents, psychochemical agents and nerve agents such as
initial use has been authorized. Threat forces consider Tabun (GA), Sarin (GB), and Soman (GD). Although
chemical weapons as an extension of conventional G-series nerve agents (GA, GB, GD and GF) are
warfare. If units understand the uses of chemical agents, classified as nonpersistent agents, some G agents may
they will be better able to avoid chemical hazards. persist for hours to days. Refer to Table 1-2 in Chapter 1
of this Field Manual or FM 3-4 for persistency data.
Types of Chemical Agents Nonpersistent agents should be expected along the
Chemical agents may be classified persistent, forward line of troops (FLOT), and against units in
nonpersistent and dusty. Threat forces classify chemical contact with the attacking echelon. These agents are used
agents according to their effect on the body. They identify to immobilize, injure, or hinder activities of the unit
six major types—nerve, blood, blister, choking, under attack. For example, threat may use a blood agent
psychochemical, and irritants. at a critical moment in battle to force troops into a higher
MOPP level. Forcing troops into a higher MOPP level
Persistent reduces morale and degrades performance. Another
Threat forces are known to stockpile persistent and advantage is that the threat would not need to
nonpersistent agents. decontaminate the area before occupying it. Nonpersistent
Persistent agents are used to impede the use of critical agents act through the respiratory system or through skin
terrain, channelize the attacking force, or contaminate absorption.
materiel. Persistent chemical agents are used to produce Nonpersistent agents are used to—
casualties (immediate or delayed). Immediate casualties Create favorable fighting conditions.
occur when the soldier inhales the vapor. Delayed Produce casualties prior to an assault.
casualties occur and is absorbed through the skin Degrade and suppress troops by forcing them into a
demonstrating the need for protective equipment. higher MOPP level.
Persistent agents are used to— Allow occupation without decontamination.
Contaminate rear area supply depots. To avoid nonpersistent agents-
Defend avenues of approach. Avoid low areas and enclosed spaces where vapors
Neutralize personnel defending a strong point. lingers.
Protect flanks. Camouflage
Degrade unit efficiency, Maintain discipline
To avoid persistent agents-

3-0
 FM 3-3

because it is the optimum distance that the detector can be

Dusty placed upwind and a chemical agent cloud cannot slip
Dusty agents, (toxic dust or dust-impregnated agents as behind the alarm and hit the unit.
they may be referred to) are not new. These agents have
been subjected to extensive scientific research since the
1930’s. These agents are primarily mustard (HD) and the
nerve agent sarin (GB) impregnated onto a solid sorbent
(usually on silica) and dispensed as aerosols. These agents
generally have a lower vapor pressure and a dramatic
increase in inhalation toxicity.
Vapors off gassing from the solid sorbent may be
detected by the M256 Chemical Agent Detector Kit,
Chemical Agent Monitor (CAM) or when mixed in
water, by the M272 Water Test Kit.

Detection and Identification

Following OPSEC measures, the next most important When using this chart, commanders must realize that if
step in chemical contamination avoidance is detecting and the concentration of chemical agents is low, the alarm
locating chemical agents. Once agents are detected units may not respond for several seconds. Also the average
can be warned to take appropriate protective measures, time for individuals to mask (including reaction time) is
and can plan operations to minimize the effects of about 15 seconds. Warning times for different distances
chemical agents. Detection allows individuals to survive and wind speeds can be determined using the following
and units to accomplish their missions. formula—
Chemical agents will be delivered either directly on Warning time (see) = Distance (m) x 36
unit positions (on-target attacks) or upwind to drift over Wind speed (kmph) x 10
the unit position (off-target attacks). Detection methods 36 is the factor to convert hours to seconds
differ for each type of attack. 10 is the factor to convert kilometers to meters
On-target attacks produce immediate casualties by This method can be used only to warn against agents
contaminating troops and equipment. If the attack is drifting into the unit location. On-target attacks
intended to produce immediate casualties, a large amount circumvent detectors placed at this maximum distance.
of agent must be delivered in a very short time (within 30 Automatic Chemical Agent Alarm
seconds). The M8 series alarm does not detect all
chemical agents; it takes several seconds to respond to The automatic chemical agent alarm (ACAA) can be
those agents it does detect. Therefore, a large percentage used in a stationary position. Keep the detector upwind at
of troops might be exposed to chemical agents before the all times.
alarm sounds. As an example the M8 Alarm will sound As soon as a unit arrives in an area it plans to occupy,
within 2-3 minutes when exposed to an nonpersistent it emplaces the alarms. The detectors are always placed
nerve agent concentration of GB at 0.23 mg/m and
3
upwind. Unless circumstances do not permit, they should
persistent nerve agent VX at 0.4 mg/m . The M8A1 be no more than 150 meters upwind from the farthest
alarm will sound within 1-2 minutes with an agent3 upwind position of the unit. This warns the soldiers
3
concentration of GB at 0.1 mg/m and VX at 0.1 mg/m . upwind as well as the soldiers farther downwind. The
This means that troops must recognize the delivery of the detector units should never be placed more than 400
chemical agent, observe a color change in the detector meters from the alarm unit. Otherwise the signal may not
paper, or recognize symptoms of chemical agent be strong enough to sound the alarm. The optimum
poisoning. spacing of 300 meters between detectors reduces the risk
Off-target attacks are easier to protect against. Units that a chemical agent cloud will drift between detectors
use the M8 series alarm to alert the unit that a chemical without sounding the alarm. The number of alarms
agent is about to drift over their position. Detector paper needed to protect a unit depends on the unit size. The
also can alert units that they are moving into a larger the unit front, the more detectors are needed to
contaminated area. Protective action can then be taken warn the unit. In this case, front means the upwind
before troops are exposed to the agent. Table 3-1 shows direction. Front could be the left or right flank or the
the arrival time of chemical agents for various wind forward or rear edge of the unit. Table 3-2 gives an
speeds. A distance of 150 meters was chosen for the table estimate of the number of detectors needed for fixed
employment of the alarms.

3-1
FM 3-3

NOTE—When emplacement is completed for your

element, you should show where the alarm’s are by
placing them on your range cards. For night operations
a strip of engineer tape may be placed on the alarm so
that they may be located.
When emplacing alarms, the wire connecting the alarm
and detector must be protected from indirect fire. This
can be done by burying the wire. The wire also should be
checked periodically (at least once every four to six
hours) to ensure it has not been broken or cut.
Chemical alarms are usually employed at unit level. The M8 series alarm is designed to operate in a
Exact positions for the alarms must be determined based temperature range of -40°F to 120°F. During the war in
on wind speed, wind direction, terrain, and tactical the Persian Gulf deployed units experienced a high
situation. The commander, with advice from the unit frequency of false alarms. This was due to a multitude of
NBC NCO, will choose the actual positions. Figure 3-1 problems. However, the two principle causes were
shows how a fixed emplacement might look. Note how identified as the high temperatures the alarm was
the detectors are positioned and how these positions operating in and the dust concentration in the air. The
change when wind direction and unit position changes. high temperature problem was reduced by placing the
alarm up off the ground on wood or boxes and placing the
alarm in a shaded area either natural or manmade, such as
under camouflage netting. High dust concentrations
required replacing filter paddles in the alarm more
frequently (1 every 1-2 hours of operation).
Since most units do not have many alarms, do not leave
them behind. Ensure alarms are listed on vehicle load
plans. The company chemical NCO, who controls placing
and moving the alarm must ensure the unit personnel
know when to retrieve the alarm. This is best done by
making an alarm range card similar to a mine field range
card.
The vehicular mode is only for the use of the vehicle’s
power supply. The backpack configuration is for small
unit dismounted operations to facilitate transport. At no
time should the M8 alarm be operated while moving.
However, once vehicle brackets for newer vehicles
become available (HUMMWV, M2, M1) the M8A1
alarm may be used on the move. M8A1 alarms may also
be placed on helicopters while in flight but these alarms
must operate on battery power.
Chemical Agent Monitor
CAM, Figure 3-2, is a vapor monitor and can only
report conditions at the front of the nozzle assembly. It is
a point monitor only and cannot give a realistic
assessment of the vapor hazard over an area from one
position. It is necessary to move the CAM around the
area carrying out a complete reconnaissance if a proper
assessment is to be made of the vapor hazard in the area.
When conducting reconnaissance with the CAM in a
windy area, (such as on board ship, ground surface winds
at 8 kmph or higher) use a funnel, paper cone or a can
with a hole punched in it the size of the CAM probe.

3-2
 FM 3-3, C1

(Any assessment will probably be made in conjunction with

other detection methods).
Check for obvious vapor sources, and known interferents.
NOTE If there is a source of vibration in the
area, WAIT may be displayed momentarily when Remove and discard the filtered nozzle standoff and place
searching for agent. This is especially true when the nozzle protective cap assembly onto the front of CAM case
the CAM is used on board aircraft while in flight. and re-establish a clear air background.
There are a few vapors present in the atmosphere that can, Remove nozzle protective cap assembly and add a new
in some circumstances, give a false response in CAM. The filter. If false response reoccurs, CAM may not be operable
situations most likely to give a false response are in enclosed in the immediate area. Remove source of interferent (if
spaces or when sampling near strong vapor sources (dense possible) or replace nozzle protective cap assembly and
smoke). Some of the types of vapors that have been found to remove CAM from area.
give false readings are given below: When investigating the contamination of a person, object,
Aromatic vapors. Included in this category are groups of vehicle, aircraft or piece of equipment, it is essential to first
materials such as perfumes and food flavorings. Some brands establish what general vapor hazard exists around the
of after shave and perfume can give a response in G mode suspected contaminated equipment. If a reading higher than
when CAM is held close to the skin, for example as in casualty the background level is obtained, then the equipment is
handling procedures. Some sweets such as peppermints and contaminated. If the reading is the same as the background,
cough lozenges and menthol cigarettes can cause a response then it may be contaminated or the CAM may merely be
in G mode if the breath is exhaled directly into the CAM inlet. recording the background vapor hazard. Care must be taken
when assessing the contamination of an object from the
Cleaning compounds. Some cleaning compounds and information indicated on the CAM display. CAM display bars
disinfectants contain additives which give them a pleasant and corresponding warning are depicted in Figure 3-3.
smell. Some of these additives such as menthol and methyl
saticylate (MS) can give false responses in the H mode. The CAM is used to search out clean areas, to search and
Ammonia gives a false response in the G-mode. Cleaning locate contamination on personnel, equipment, ship’s
materials are, by nature, spread over large surface areas and, structures, buildings and terrain, structures, aircraft and land
therefore, provide a considerable vapor source, particularly in vehicles, buildings and terrain, and to monitor the
enclosed spaces. effectiveness of decontamination. CAM can also be used for
monitoring collective protection shelters and the chemical
Smoke and fumes. The exhaust from some rocket motors contamination of aircraft while in flight. The Chemical Agent
and the fumes from some munitions can give responses. Since Monitor responds to nerve and blister agent vapors down to
monitoring with CAM in these situations is unrealistic, few the lowest concentrations that could affect personnel over a
problems should arise. Additional interferents are listed in short period.
Table 32-a.
The CAM has two operating modes, selectable by means
If CAM is suspected of giving a false reading: of the G H mode pushbutton switch. In the G mode, CAM
Stay masked. monitors for G-series nerve agents as low as

3-3
FM 3-3

3 3
0.03 mg/m ; V-series nerve agent as low as 0.01 mg/m , During normal operation, especially in dusty or dirty
both within 1 minute. In the H mode, 3
CAM monitors for environments, the ICAD may require external cleaning.
blister agents as low as 0.01 mg/m within one minute. To remove external dust or dirt, remove the sensor
The selected mode is indicated on the display assembly by module from the electronics/alarm module. Cover the
a G or H. An ON/OFF pushbutton switch applies 6 V DC connectors with your fingertips. With the connectors up,
battery power to the CAM. A nozzle protective cap flush the sensor module with clean water, and then gently
assembly contains material to clean the air within the shake excess water from the unit. With the LED
CAM; the cap assembly is located in the front of the indicators and audio alarm up, flush the electronics/alarm
CAM whenever the CAM is not being used to monitor module with clean water, and then gently shake excess
for contamination. Additional information on the water from the unit. Do not use soap or any cleaning
operation of the CAM may be obtained from TC 3-4 or solution on the ICAD. Do not scrub or wipe the sensor
appropriate TM. membranes.
The normal operating temperature range of the ICAD
is 0 to 113 degrees F (-18 to 45 degrees C). The ICAD
can be stored prior to activation at temperatures ranging
from 40 to 150 degrees F (-40 to 65 degrees C).

CAUTION
Do not store or operate the ICAD at temperatures
Individual Chemical Agent Detector (ICAD) below or above the specified temperature ranges.
The USMC issued ICAD (Figure 3-4) includes two The ICAD could be permanently damaged.
electrochemical sensors, each of which is covered by a
thin diffusion membrane. One sensor
3
is sensitive to nerve
agents (GA, GB, GD 0.53 mg/m m 120 seconds), blood ABC-M8 Chemical Agent
agents (AC, 250 mg/m3 in 120 seconds), and choking Detector Paper
agents (CG 25.0 mg/m in 15 seconds); the other sensor
3
detects blister agents (H, L 10.0 mg/m in x seconds). ABC-M8 Chemical Agent Detector Paper detects liquid
Chemical agents in the air diffuse through the membranes chemical agents. It& used whenever chemical agents are
on the faces of the ICAD sensors, and are collected by suspected. Every soldier carries a booklet of ABC-M8
the electrolyte behind the membranes. The chemical agent Paper in the mask carrier. Each booklet contains 25
concentrations in the electrolyte are measured by sheets of paper. This paper turns colors when the paper
multiple-ellectrode electrochemical sensor systems. When touches a chemical agent. V-type nerve agent turns the
the concentration reaches a preset threshold level, an paper dark green, G-type nerve agent turns it yellow, and
audio alarm sounds and a light-emitting diode (LED) a blister agent turns it red.
comes on. Night operations cause problems when using ABC-M8
Paper. The paper must be read in white light. Since

3-4
 FM 3-3, C1

ABC-M8 Paper is used to check suspected areas for and classifying chemical agents. The M256 series
contamination, it can be brought into a white light area contains ABC-MS Chemical Agent Detector Paper for
for reading. During night recon operations, the monitor liquids and samplers/detectors for vapors. An improved
can take several marked samples, then bring them back to M256 Detector Kit will also be capable of detecting T2
the vehicle for reading. The paper is used by blotting it mycotoxin.
on the suspected contaminated surface. Do not rub the M256 series samplers/detectors are used primarily to
ABC-M8 Paper against the surface because false positive determine the type of chemical agents present. A unit
(red) streaks are produced. may have noticed an attack or the alarm may have
sounded. The M256 series is then used to check if there is
M9 Chemical Agent Detector Paper a chemical agent present and to identify the agent.
Chemical Agent Detector Paper, M9 is the most widely The M256 series also causes OPSEC problems during
used method of detecting liquid chemical agents. It is more hours of limited visibility. A white light is needed to read
sensitive and reacts more rapidly than ABC-M8 Paper. M9 both the ABC-M8 Paper and the sampler/detector. The
Paper reacts to chemical agents by turning a red or reddish light must be shielded from enemy observation. This can
brown color. Place the M9 detector paper to opposite sides be done by using a pancho or other suitable covering.
of the body. If you are right handed, place a strip of M9
paper around your right upper arm, left wrist, and right M272 Water Testing Kit.
ankle. If you are left handed, place the M9 paper around Chemical Agents
your left upper arm, right wrist, and left ankle. It is also
attached to large pieces of equipment (eg: conditioning The M272 Water Testing Kit, Figure 3-5) Chemical
systems, shelter or van entrances or vehicles). When Agents is a lightweight portable kit that will detect and
attached to equipment it must be placed in an area free identify harmful amounts of chemical warfare agents
from dirt, grease, and oil. This is especially important since when present in raw and treated water. The kit will detect
petroleum products and DS2 also cause the paper to change cyanide (AC) to 20 mg/liter, mustard (HD) to 2.0
color. mg/liter, lewisite (L) to 2.0 mg/liter and nerve agents
M9 Paper is especially useful in detecting on-target (both G and V series) to 0.02 mg/liter. Water containing
attacks and keeping soldiers from entering contaminated agents in less than these concentrations is permissible for
areas. Whenever pink, red, reddish brown, or purple short term (up to 7-day) use, in cold or warm regions
color appears on the paper, suspect the presence of with up to 5 quarts per person per day usage. These kits
chemical agents. As soon as M9 Paper indicates the are usually found in chemical reconnaissance units,
presence of chemical agents, soldiers and units must take medical units and units with water purification or
protective action to keep from becoming grossly transportation missions.
contaminated. The results of the M9 paper should be
confirmed with the M256 kit.
Night operations present some problems when using
M9 Paper. Color changes will not show up when a
flashlight with a red filter is used to read the paper. White
light must be used. This could cause some serious
OPSEC problems, especially for frontline troops.
Commanders must realize that there is a risk if they do
not establish procedures for checking M9 Paper for color
changes. Soldiers can be rotated into a white light area or
the M9 Paper can be collected periodically for reading.
M256 Series
Chemical Agent Detector Kit
The M256 series Chemical Agent Detector Kit is
capable of detecting both liquid and vapor concentrations
of chemical agents. It detects chemical agents in the3
following concentrations-nerve
3
(G series; 0.005 mg/m 3
VX; 0.02 mg/m
3
within 15 minutes), blister (H; 2 mg/m
12 mg/m3
within 10 minutes), and blood agents (AC; 7
mg/m within 10 minutes). The M256 Kit is issued at
squad level, so every squad has the capability of detecting

3-5
FM 3-3, C1

FOX, XM93, The FOX has nuclear, chemical and biological

NBC Reconnaissance System sampling equipment that consists of—
A sample collecting device with transport container.
(NBCRS) Glove (rubber) protection for collecting samples
The FOX (Figure 3-6) is a fully integrated NBC The equipment is fixed outside the vehicle and is
reconnaissance system with the following characteristics operated manually using the glove and glove port device.
and operational capabilities. The FOX is also protected against electromagnetic
Six wheel, amphibious armored cargo and tactical pulse (EMP), transi-radiation effects on electronics
transport vehicle powered by a V8 diesel engine (320 (TREE), and electronic countermeasure (ECM).
horse power). The maximum speed is 65 miles per hour The FOX system is assigned to the following units.
with a cruising range of 500 miles. It weighs 18.7 tons Heavy Division (NBC recon platoon) has six (6)
combat loaded and 16.9 tons without the crew and vehicles.
ammunition. It is equipped with a 40mm smoke grenade Armored Cavalry Regiment (ACR) has six (6)
launcher and an M240E1, 7.62mm machine gun. The vehicles.
FOX is also equipped with a collective protection system Motorized Brigade has six (6) vehicles.
which keeps the crew’s working area free from NOTE—The FOX system will also be assigned to the
contamination. NBC reconnaissance chemical companies assigned to the
The integrated NBC defense/detection system has four TAACOM/CORPS when these companies are placed in
key components. active duty status. The TAACOM/CORPS units are
Mobile Mass Spectrometer (MM1)-Consists of a projected to receivw 36 systems each.
detection membrane probe system with an air/ground Employment concepts—
probe, and a rugged microprocessor. The system can Offense—During offensive operations (such as
monitor and identify all known chemical agents. movement to contact), the FOX NBCRS should be
Radiac Equipment (ASGI-Consists of two probes positioned well forward just behind the leading combat
installed in the exterior ports on each side of the vehicle elements to facilitate contamination avoidance,
connected to the radiation detection, identification, and responsiveness to reports of NBC contaminations, and to
computation instrument/recorder inside the vehicle. provide freedom of maneuver.
Vehicle Orientation System (VOS-25)—Operates Defense— During defensive operations, the FOX
through the principles of gyroscopic motion with a motion NBCRS should be used to conduct NBC reconnaissance
sensor attached to the vehicles’ transmission. The unit operations in the rear areas to ensure that the routes to
(VOS-25) is integrated with the radiation (ASGI) and the and from the corps, brigade, and division support areas
chemical detection (MM1) and can accommodate are free of NBC contamination. The FOX systems are
depiction of chemical and radiological contamination on also used to find clean fall back positions for the fighting
the map with the push of a button. forces during withdrawal and retrograde operations.
NBC marking equipment—The vehicle has an NBC
Marking Kit with an air-lock (glove port) through which Remote Sensing
the NBC contamination marking buoys are positioned. Chemical Agent Alarm XM21
(RSCAAL)
This joint service system is a passive infrared
spectroradiometer that uses an on-board microprocessor
to detect and identify agent clouds. It operates by viewing
a background scene (sky, terrain, buildings, etc.) and the
airpath along its line of sight. When agent cloud enters
the line of sight the new spectral information is compared
to the stored background information and the specific
infrared emission characteristics of a known agent. The
detector scans along a 60-degree horizontal arc through
seven 1.5 degree windows, the centers of which are 10
degrees apart. One scanning cycle (60-degree arc) takes
less than 60 seconds. The detector has seven scan position
lights that indicate which field of view (FOV) an agent
cloud occupies. This allows the operator to determine an
azimuth direction to the cloud and obtain an indication of

3-6
 FM 3-3

horizontal movement. The XM21 is designed to operate

within the temperature range of -25° to 120°F. Reporting
The XM21 can perform the basic missions of When chemical agents are detected and/or identified,
reconnaissance and point or area surveillance. the unit must report this information immediately to
Employment of the XM21 must be tailored to fit the higher headquarters. Below company level, this is done
tactical situation and the capabilities of the detector. with a SPOT report. The company NBC defense team
Common missions for the detector are—scan a defensive then puts the report in an NBC 1 format and forwards it
front, vector battlefield assets, monitor barriers and to battalion. Figure 3-7 is a sample NBC 1 Chemical
obstacles, monitor avenues of approach, and search areas Report.
between and adjacent to enemy and friendly forces. If the unit uses the data from it’s own Chemical
The selection of general sites requires a map Downwind Message to report attacks, this weather
reconnaissance of the area of operations. Personal information must also be reported on the NBC 1
reconnaissance may be carried out when the tactical Chemical Report. This is accomplished by including line
situation permits. This technique is especially useful when items Yankee (Y) and Zulu Alpha (ZA) on the NBC 1
the XM21 is used in the area surveillance mission where Chemical Report. If the attack is unconfirmed or agent
the M8A1 system is being replaced or augmented. When unknown, line item Zulu Bravo (ZB) will be included in
selecting specific positions for the system, the team leader the report at battalion level. Line ZB is the remarks line
conducts a full reconnaissance of the general site. in the NBCWRS. Battalion chemical staff will include
Selection of the specific site must take into consideration remarks indicating what measures have been taken to
the line of sight limitation of the XM21. When the confirm the attack.
situation permits, terrain profiles may be requested from By the time the attack is confirmed, the NBC 1 Report
the G2 to ensure line of sight to the target area. would already be at division level. In the event that the
A properly emplaced XM21 will detect significant report was based on a false alarm, an NBC 3 Chemical
G-agent, HD, and Lewisite munitions events and Report will still be issued but will include line item ZB
resulting clouds at ranges out to 5km with a greater than stating the strike serial number and the words “cancelled
85 percent probability of detection. Other features - false alarm”.
include:
Stand-off detection for G-agents, HD-mustard, and
L-blister agent clouds. Concentration sensitivity levels are
recorded as CT = concentration x time. For nerve3 agents
this sensitivity level is recorded as 33 mg - min/m and for
blister this level is 150 mg - min/m .
Operates under normal conditions without degradation
at night.
To set-up in the tripod mode by two trained personnel
takes 10 minutes.
Limitations.
Requires line of sight. Must be leveled and sighted to
the terrain to maximize detection probability.
Performance degraded by heavy rain, snow, dense Data Evaluation
foliage, and strong winds. Data evaluation consists of determining the attack
System must be stationary to operate. location, confirming type of agent, means of delivery,
A false alarm may occur when subjected to low angle type of attack, and assigning a strike serial number for
direct sunlight on the optical window. each attack. Confirming the attack is critical, especially if
Does not detect blood agents. it is the first reported chemical attack in the theater.
Does not detect residual vapor hazard from Confirmation includes collecting samples of the suspected
evaporating liquid persistent agents under normal agent, obtaining pieces of shell or casing fragments,
conditions. medical analysis of casualties (living or deceased),
witness interviews and intelligence reports. Refer to
Chapter 5 or FM 3-19 for detailed procedures on how to
collect these samples. To confirm that a chemical attack
has occurred, the M93 NBC reconnaissance vehicle
should be dispatched to the area in question to take

3-7
FM 3-3

samples. In the event that this vehicle is not available,

units should take additional samples using 2 or more Chemical Downwind
sampler detector tickets from two different M256 detector Message
kits or by using additional ABC-M8 detector paper strips. The Chemical Downwind Message (CDM) contains all
In the event that an M8A1 alarm goes off, this would the weather information needed to calculate a chemical
normally indicate that a nerve agent is present. If liquid downwind hazard. The CDM is useful because it provides
droplets are not present in the area, this may indicate the the local wind speed, wind direction, stability category,
presence of a G-series nerve agent or a vapor cloud from and relative humidity in a short concise statement. It is
off gasing VX contamination. To determine what type of prepared by corps and division NBCCS from information
nerve agent is present, the M93 NBC Reconnaissance obtained through the US Air Force Air Weather Service
vehicle should be dispatched to the area concerned. This (AWS), Staff Weather Officer, or the Fleet Weather
vehicle is capable of determining what type of nerve Service.
agent is present. In the event that this vehicle is not The CDM is issued every six hours and is valid for
available, units must rely on the ABC-M8 Paper to three consecutive two-hour periods. It contains the
determine whether G or V series nerve agent is present. following—
The M256 kit sampler/detectors will not make this Date-time group of the observation.
differentiation. This test may not provide the necessary Date-time group for basic data is the time the first
information required if no liquid droplets are available. If forecast is effective. Adding two and four hours to this
the ABC-M8 paper test proves to be insufficient or time gives the effective times for the other two forecasts.
indicates that a G nerve agent is present, units should rely Area of validity is the area affected by the CDM. It
on available intelligence information to determine what could be a map sheet number or an area, such as division
type of agent fill is available to the enemy. Compare this or corps.
information with the means of delivery for the chemical Air stability category describes the projected air
agent attack to determine the extent and duration of the stability. It will be one of seven numbers which
hazard area. If units are still unable to determine what correspond to stable, neutral, or unstable conditions.
type of G series nerve is present, assume worst case,
Type A Case b. The NBCC plots all NBC 1 Reports and
consolidates data pertaining to each attack. From this
data, the NBCC prepares the NBC 2 Report and assigns a
strike serial number. A record of these numbers is kept in
the strike serial log. Figure 3-8 is a sample NBC 2
Report. A suggested format for a log is shown in Figure
3-9.

3-8
 FM 3-3, Cl

Surface air temperature is the average temperature of operations. Units may estimate the air stability category
the air in the forecast area. by observing local meteorological conditions. A field
Surface wind speed and direction are the expedient method of obtaining the necessary weather data
representative wind speed and direction during the may be used when all other sources are unavailable. In
forecast period. order to obtain local weather data, units may obtain a Belt
Relative humidity is the average humidity for the Weather Kit (NSN—6660-01-024-2638) and barometer
forecast period. (NSN–660-00-551-3998) or use the equipment listed
Significant weather phenomena refers to any weather below. The weather information obtained in this manner
conditions that could affect either the distance the cloud is only for that particular area. for that period of time. It
travels or the duration of the agent in the hazard area is by no means, a forecast from which a CDM maybe
Cloud cover in the area of validity. produced. However, it is a local method of verifying
CDM weather data. If this method is used for local
Preparing the weather, include this data on the NBC 1 Chemical
Report.
Chemical Downwind M1 Ananometer (66000663-8090)
Wet Bulb, Globe, Temp (C°) (6665-00-159-2218)
Message Lensatic Compass
Division NBCC is usually the lowest level that prepares Step 1. Measure windspeed and direction with the
a Chemical Downwind Message. Separate brigades also lensatic compass and ananometer. Use the highest
may be required to prepare a CDM when operating
independently. Figure 3-10 is a sample CDM.
The first step in preparing the CDM is to acquire the
weather data. The Air Weather Service (AWS) is the best
source for this information. They provide weather
forecasts for division or corps areas. Weather information
can also be obtained from the artillery meteorological
section. Although they cannot provide forecasts, they can
provide current weather information.
The next step is to break it down into three consecutive
two-hour increments. Line Whiskey Mike is used for the
first two-hour increment, line X-ray Mike for the second,
and line Yankee Mike for the final two-hour increment.
Then the NBCC translates this data into codes and puts it
in the proper format. Each forecast line contains 12
digits.
The first six digits represent the downwind direction
and wind speed. The last six digits represent the air
stability, temperature, humidity, significant weather
phenomena, and cloud cover (see Figure 3-11). Weather
data which is unavailable or for which no code exists is
represented by a dash.
A valid CDM may not always be available from the
corps or division NBCC or applicable to the unit area of

3-9
FM 3-3

windspeed recorded. Take temperature and humidity Compare the difference in air temperature to the normal
readings using the wet bulb at one meter above the or expected change in temperature. The normal change in
ground. Obtain readings every two hours if practical, but temperature is 1 degree cooler for every 100 meters
not greater than four hours. increase in altitude. The four possible gradient conditions
Step 2. Determine the four transition periods of are inversion, neutral. lapse, and elevated inversion.
windspeed and direction during the day. Take average of
the readings during each transition period. Inversion Temperature Gradient
The most difficult aspect is determining (Stable-S).
the sun by observation. Since most units do not have If the air at the higher altitude is warmer than the
equipment to do this, make the best estimation possible. normal temperature at the lower altitde, the air will not
Example—It is morning. The sun’s angle is 45 move vertically. This represents an inversion temperature
degrees, and the sky is less than half covered. Find the gradient. This condition usually exists on a clear or
time of day (morning) and angle of sun (45 degrees) on partially clear night when middle and low clouds cover
the chart at Table 3-3. Find the sky condition (less than less than 30 percent of the sky, and on early mornings
half covered). Read across and down to the point where until about 1 hour after sunrise when the wind speed is
the lines converge. The air stability category is U. less than 5 knots. It is characterized by a minimum of
convection currents and by maximum air stability-ideal
Atmospheric Stability for enemy employment of chemical agents. Weak
inversion conditions tend to prevail during the day over
Charts large bodies of water.
The stability of a chemical or biological agent cloud is
directly effected by the temperature of the air at the Neutral Temperature Gradient.
surface of the earth and the first few meters above the A neutral condition exists when air temperature shows
surface. very little or no change with air increase in altitude. This
represents the neutral temperature gradient. This
Temperature Gradients condition usually exist on heavily overcast days or nights
The air stability categories are dependent on the at 1 or 2 hours before sunset or 1 to 2 hours after sunrise
temperature gradient (difference of air temperature at two when the middle and low clouds cover more than 30
attitudes). The temperature gradient is determined by percent of the sky. Independent of cloud cover and time
measuring the air temperature at two different altitudes. of day, a neutral condition may also exist when the wind
speed is greater than 5 knots. Additionally, periods of
precipitation are normally accompanied by a neutral
condition. A neutral temperature gradient is most
favorable for enemy use of biological agents because the
associated wind speeds result in larger area coverage.
Lapse Temperature Gradient
(Unstable-U).
If the air at the higher altitude is cooler than the
expected difference, then there will be vertical movement
of air creating turbulence. This condition normally exists
on a clear day when the middle and low clouds cover less
than 30 percent of the sky and when the wind speed is
less than 5 knots. This is the least favorable condition for
the enemy to employ chemical or biological agents. Over
large bodies of water, weak lapse conditions tend to
prevail at night. When a lapse condition exists, area
coverage without diffusion will be enhanced with a steady
low wind speed of 3 to 7 knots.
Elevated Inversion
(Stable).

3-10
 FM 3-3, C1

Elevated inversion may occur when cooler air settles Units need to make a simplified prediction using a
under warmer air. This condition will generally occur Chemical Downwind Message and a simplified template.
when a warm and cold frontal system converge or over The template can be made out of acetate, overlay paper,
large bodies of water. The significance of an elevated or plastic. Figure 3-12 shows a sample simplified
inversion layer is that the layer will act as a lid over the predictor. The following steps show you how to use a
surface. This “lid” traps air particulants as well as simplified prediction.
chemical agents, in a concentrated form, at a given height Step 1. Get the wind speed from the CDM. If it is s
above the ground, thus presenting an increased threat to 10 kilometers per hour, use the circular portion of the
aircrews. The Staff Weather Officer must report this prediction. If it is > 10 kilometers per hour, follow the
condition, when it occurs to the NBCC and divisional remaining steps.
aviation units. Step 2. get the wind direction from the CDM. Mark
Once you have obtained the air stability category from that direction on the compass circle of the template.
the basic chart, enter the adjustment chart with that Step 3. get the air stability code from the CDM; use
category. Select the appropriate weather and terrain this code (U, N, or S,) to determine the downwind
condition from Table 3-4. Read across to where they distance.
intersect and extract the final stability category. Use this Step 4. Place the template on the map with the attack
stability category to determine the maximum downwind center of the prediction (the cross mark) over the actual
distance. For more information on field expedient attack center. Rotate the predictor until the
behavior of chemical agents, see FM 3-6. downwinds direction points toward GN.
Step 5. Draw the downwind line perpendicular to the
Simplified downwind direction using distance obtained in step 3.

Hazard Prediction
The simplified hazard prediction tells subordinate units
whether they are in a chemical downwind hazard area.
Since Type A attacks present the greatest hazard, the
simplified procedures are based on that type of attack. It
is valid until an NBC 3 Report is received from higher
headquarters.

3-11
FM 3-3, C1

Duration of Agent Air-Contaminating Agents-Type A

For ground contamination, the temperature is one of Type A agents are normally dispersed as an aerosol or
the major factors for determiningg how long the agent vapor cloud with little or no ground contamination. A
presents a vapor hazard. Refer to tables 3-6 through 3-17, nonpersistent nerve agent employed upwind of the target.
in Chapter 3, FM 3-4, NBC protection. These charts Air-contaminating agents are normally dispersed in
cover duration of agents at different temperatures, which ground-bursting munitions such as artillery shells and
will allow the commander to determine when to start multiple rocket launchers. This type of attack is a Type A
MOPP opening/unnmasking procedures. attack. Refer to flow chart on pages 3-13 thru 3-16.
NOTES
1. These charts are worse care using a 500 pound Ground-Contaminating Agents-Type B
bomb. Type B agents are normally dispersed in liquid form to
2. In making hazard estimates, vapor is the contaminate surfaces. Persistent nerve and mustard agents
determining factor within the attack area as well as in are examples of this type of attack. Refer to flow charts
the downwind hazard area. However, the duration of on pages 3-13 thru 3-16.
hazard from contact with bare skin is difficult to predict. Ground-contaminating agents are normally dispersed
Duration can only be determined by the use of chemical by aircraft spray tanks, air-bursting artillery shells,
agent detection devices. rockets, missiles, and mines. Evidence of ground
3. When temperatures are consistently low, the contamination on may include the observer’s report of agent
duration of ground contamination maybe Linger than falling to the ground from air-bursting munitions,
indicated in the table. The absence of vapor does not identification of agent with ABC-M8 paper, positive
preclude the presence of contamination. response of M9 Paper, or the identification of blister
agent with the M256 series sampler, or reading on the
CAM.
Chemical To predict a downwind hazard area, whether the attack
Downwind Hazard was a Type A or Type B, you need the following
information
Prediction An NBC 1 or NBC 2 Chemical Report.
The hazard from a chemical attack is not confined to Detailed meteorological information Chemical
the area directly attacked. The resulting vapor or aerosol Downwind Message (CDM) or similar information.
travels with the wind and can cover a large area This information is then used to determine the
downwind of the attack area. To prevent casualties, you appropriate procedure to predicct the downwind hazard
must quickly identify the possible hazard and warn units area. There are six cases that must be considered. Use the
within the hazard area. This section provides instructions chart on the following page to determine which of the six
for defining the probable hazard area resulting from a procedures to use when constructing the downwind
chemical attack. hazard prediction.
The prediction of the hazard areas is only an
approximation. Terrain and weather, as well as delivery Plotting the Downwind Hazard-Type A
system variations, modify the hazard area. In addition, Two cases must be considered when plotting the
the methods used to predict the downwind hazard are downwind hazard area from a Type A attack.
safesided for troop safety. This assures that the hazard Case a wind speeds of 10 kmph or less.
will be within the predicted area. This gives units in the Case b wind speeds greater than 10 kmph.
area time to take appropriate precautions. These Type A, Case a (Figure 3-13, page 3-17) is for wind
procedures are derived from STANAG 2103 and ATP-45 speeds of 10 kilometers per hour or less.
with change 1. Step 1. Get the attack location from an NBC 1 or an
NBC 2 chemical Report and plot the location on the map
Type of Attack or template (preferably UTM scale 1:50,000).
For hazard prediction, all attacks are classified as Step 2. Draw a 1-kilometer-radius circle around the
either Type A, air-contaminating agents or Type B, center of the attack location. The area within the circle
ground contaminating agents. represents the attack area.
The prediction of downwind chemical hazard areas Step 3. Draw a 10-kilometer-radius circle concentric
depends on the wind speed, temperature, and humidity; with the 1-kilometer circle. The area within the circle
and for ground-contaminating agents-the size of the attack represents the hazard area.
area. Step 4. Send an NBC 3 Chemical Report to

3-12
FM 3-3, C1

3-13
FM 3-3, C1

3-14
FM 3-3

3-15
FM 3-3, C1

3-16
 FM 3-3

units/installations in the hazard area (PA is 010). downwind distance of the hazard area. Plot the maximum
Type A, Case b (Figure 3-14) is for wind speeds downwind distance and draw a line perpendicular to the
greater than 10 kilometers per hour. downwind direction.
Step 1. Get the attack location from an NBC 1 or an Step 6. Extend the downwind direction line upwind 2
NBC 2 Chemical Report and plot the lcation on a map. kilometers from the attack center. From this point, draw
Step 2. Draw a GN line. two lines that just touch the attack area circle and extend
Step 3. Using the attack location as a center, draw a them until they intersect the maximum downwind distance
1-kilometer-radius circle around the attack location. line.
Step 4. Obtain the downwind direction and speed from Step 7. Send an NBC 3 Chemical Report to
a valid CDM. Draw a line from the attack center units/installations in the hazard area.
representing the downwind direction-
Step 5. Find the appropriate air stability category and Plotting the Downwind Hazard-Type B
means of delivery in Table 3-5. Extract the maximum Four cases must be considered when plotting the
downwind hazard area for a type B attack. One case
(Case d) is for wind speeds of 10 kilometers or less. The
other three cases are for wind speeds of greater than 10
kilometers per hour. In all cases, the maximum
downwind distance is 10 kilometers. Therefore, the air

3-17
FM 3-3, C1

stability category does not need to be considered. The most likely occurs after a spray attack or an artillery
governing factor is the size of the contaminated area. attack of several regiments.
Three Type B cases have wind speeds greater than 10 NOTE —If you know the attack is a ground attack but
kilometers per hour. do not know the extent of it, assume it to be a Type B,
Case a (attack area < 1 kilometer). Contamination is Case b, attack.
contained within a circular attack area of 1-kilometer First, determine which case exists. Do this by plotting
radius. This most likely occurs after an artillery attack. the actual attack location on a map, then determine which
Case b (attack area > 1 kilometer 2 kilometers). of the three cases it is.
Contamination is contained within a circular attack area; Type B, Case a (Figure 3-15), occurs when the attack
the radius is greater than 1 kilometer, but less than or area is 1 kilometer or less. Plot the same as a Type A,
equal to 2 kilometers. This most likely occurs after a Case b, attack; the single exception is that the maximum
missile attack with a high airburst, for example, over downwind distance is 10 kilometers.
1,000 meters high. Type B, Case b (Figure 3-16) occurs when the attack
Case c (length of attack > 2 kilometers). Any area is greater than 1 kilometer but less than or equal to 2
dimension of the attack area exceeds 2 kilometers. This kilometers.
Step 1. Get the attack location from an NBC 1
or an NBC 2 Chemical Report and plot the location
on a map.
Step 2. Draw a GN line.
Step 3. Using the attack location as a center,
draw a 2-kilometer-radius circle around the attack
location.
Step 4. Obtain the downwind direction and
speed from a valid CDM. Draw a line from the
attack center representing the downwind direction.
Extend this line 10 kilometers downwind. Draw a
line perpendicular to the downwind direction.
Step 5. Extend the downwind direction line
upwind 4 kilometers from the stick center. From
this point draw two lines which just touch the
attack area circle and extend them until they
intersect the maximum downwind distance line.
Step 6. Send an NBC 3 Chemical Report -
to
Units/installations in the hazard area.

3-18
 FM 3-3, C1

Type B, Case c (Figure 3-17) occurs when the attack point labelled “B”, as shown Figure 3-17.
area is greater than 2 kilometers. Step 6. Prepare an NBC 3 chemical Report and send it
Step 1. Plot the estimated attack area on the map and to units/installtion within the hazard area.
establish a point at each extreme end. Draw a GN line Type B, Case d (Figure 3-18) is for wind speeds 10
from one of the points. kmph or less.
Step 2. Draw a 1-kilometer-radius circle around each Step 1. Get the attack location from an NBC 1 or NBC
point. 2 Chemical Report and plot the location on a map or
Step 3. Draw a line tangent to both circles upwind of template.
the attack area and a line tangent to both circles Step 2. Draw a 10-kilometer-radius circle around the
downwind of the attack area. attack area center.
Step 4. Regard the two circles as being two separate Step 3. Draw the appropriate radius around the center
attack areas and construct the two vapour hazard areas, as of attack as per means of delivery.
for a Type B, Case a. Step 4. Send an NBC 3 Chemical Report to
Step 5. Draw a line from the point labelled “A” to the units/installations in the hazard area.

3-19
FM 3-3, C1

Type B, Case d (special) (Figure 3-19) is for winds constant environmental conditions. When the weather
speeds less than 10 kilometers per hour and you have a changes, the NBC 3 Report may no longer apply. An
spray attack or large-scale artillery attack where the adjusted NBC 3 Report must be sent to unit/installations
length of the attack area exceeds 2 kilometers. in the new hazard area, if possible. Also notify units who
Step 1. Get the attack location from the NBC 1 or NBC may no longer be in the hazard area.
2 Chemical Report and plot the location on the map or Significant weather changes are:
template. Representative downwind speed of 10 kmph or more,
Step 2. Draw a 1 kilometer radius circle around the or if the windspeed increases from less than 10 kmph to
start and end points. more than 10 kmph or the reverse.
Step 3. Connect both the upwind and downwind sides Air stability category (applies to type A attacks only).
to designate the whole attack area. Downwind direction by 30 degrees or more.
Step 4. A ten kilometer circle should be drawn around For a charge in wind speed determine the geographical
both the start and end points of the attack. center of the frontline of the traveling cloud at the time
Step 5. Connect both the upwind and downwind sides the new data becomes available. calculate this distance
of the ten kilometer circles to designate the hazard area. by multiplying the original wind speed times to twice the
Step 6. Send an NBC 3 Chemical Report to time in hours since the attack. The center of the cloud
Units/installations in the hazard area. front is then considered to be the new center of attack
area. Once the new center of attack is determined, the
downwind hazard area is determined using the procedures
Adjusted outline for that type of attack.
Hazard Prediction
The methods previously discussed are based on

3-20
 FM 3-3, C1

Recalculation Procedures for downwind distance line.

Wind Speed Changes Step 6. Prepare a new NBC 3 Chemical Report
Step 1. If the increase in wind speed is 10 kmph, then For a Change in Direction of
the NBC 3 Chemical Report must be changed (line 30 degrees (or more)
Yankee) to alert units to the earlier arrival time- Type B Attacks.
Step 2. If there is a change from > 10 kmph to < 10
kmph or vice-versa, the new attack area must be Step 1. Using the original point of attack, reposition
determined and the new prediction must be replotted. the fan along the new downwind direction line.
Step 2. Prepare a new NBC 3 Chemical Report.
For a Stability Category Change Step 3. Units not located within the old or new fan but
(Type A, Case b). located within the arc created by the shift of the wind
should also be warned.
Step 1. Determine the distance the cloud will have
reached (current windspeed X time after attack), and mark Time of Arrival
this on the downwind direction line. The earliest an agent can be expected to arrive at a
Step 2. Using this point as the center, draw a circle location is determined by dividing the distance from the
with a radius of one half the width of fan (measured from attack center by 1.5 times the wind speed. For example,
the center pint). This is the new center of attack area. if you are 10 kilometers from the attack center and the
Step 3. Determine the maximum downwind distance wind speed is 5 kilometers per hour, the earliest the agent
with the new stability category and subtract from it the cloud would arrive at your location would be 1.33 hours.
distance the cloud has already traveled. Plot the 10km ÷ (1.5 X 5 kmph) = 1.33 hr
remaining distance along the downwind direction line to
establish the maximum downwind distance line. If the
maximum downwind distance point lies within the radius Chemical Hazard Prediction
of new attack area, extend it to the edge of the circle. at Sea
Step 4. Move twice the radius up the downwind
direction line, establish a point, and draw the tangent Chemical hazard prediction procedures at sea provides
lines from this point, just touching the edge of the attack information on the location extent, and duration of the
area circle and extending to intersect with the maximum hazard area at sea as well as along coastal regions. It
downwind distance line. provides information necessary for commanders to warn
Step 5. Prepare a new NBC 3 Chemical Report. units at sea and on the adjacent shore areas.
Definitions used in Naval Chemical hazard predictions
For a Change in Direction of are:
30 Degrees (or more) Attack Area. The attack area is the area immediately
Type A Attacks affected by the delivered chemical agents at sea or on the
shore line. If the location of the attack area is unknown, it
Step 1. Plot a point on the downwind direction line that is assumed to be located up-wind, at a distance equivalent
the cloud center would have reached (multiply current to the units maximum range of reconnaissance. The size
windspeed times the time) when the new wind direction of the attack area is assumed to be contained within a 0.5
occurred. nautical mile (NM) radius circle.
Step 2. Around this point, draw a circle with a radius Hazard Area. The hazard area is the area in which
of half the width of the fan (measured from center pint). unprotected personnel may be impaired in completing
This is the new attack area. their mission by vapor spreading downwind from the
Step 3. From the center point, plot a line representing attack area. The downwind hazard distance depends
the new downwind direction. strongly on the defined hazard.
Step 4. Subtract the distance the cloud has already Defined Levels of Hazard. In this procedure (three)
traveled from the maximum downwind distance as different levels of hazard maybe taken into account.
determined from Table 3-5. Plot a point representing the LCt50,
new maximum downwind distance and draw a line ICt5, and
perpendicular to the downwind direction. miosis
Step 5. Move twice the radius up the downwind The following dosage limits (mg x min/m3) are used.
direction line. Establish a point, and draw tangent lines
from this point, just touching the edge of the attack area
circle and extending to intersect with the maximum

3-21
FM 3-3

Agent LCt50 ICt50 ICt5 Miosis which is transmitted 4 times daily by appropriate agencies
GB 70 35 5 3 and is valid for a 6 hour period, which is subdivided into
GD 70 35 5 3 three 2 hour periods.
Only these agents are considered as a threat for naval Valuable MET information can be provided by the
forces. These chemical agents are the most damaging for attacked unit itself. Therefore units at sea reporting a
ships at sea. Naval land forces follow the procedures and chemical attack should always attempt to include actual
defensive actions outlined previously in this chapter. weather information under letter items, Y and ZA in
When preparing a NBC 3 Chemical Report, indicate NAV NBC 1 CHEMICAL or NAV NBC 2 CHEMICAL
which hazard level the predicted hazard area is based Reports. ZA may be encoded or in clear text.
upon in letter item ZB. Elevated Inversion Layers.
General Procedures Certain meteorological conditions, known as elevated
The horizontal extent of the downwind hazard area inversion layers, in the atmosphere act like a lid and trap
depends on— the agents underneath.
- The type of chemical agent, This may lead to situations in which the chemical agent
- The means of delivery (agent concentration in the concentration aloft is very much higher than at the
attack area), surface. The stability conditions detemined at the surface
- the meteorological conditions, and are neutral or even unstable in these cases, resulting in
- the defined hazard (hazard level). much shorter hazard distances.
The vertical extent hazard extends at least up to 150 Such situations are indicated in the NAV CDM by the
meters above the sea surface. Warn air crews flying low letter “S” appearing in the coded significant weather
level. phenomena. In this case, air crews must-be given an
Chemical attacks may basically be divided into- appropriate warning.
- Air contaminating attacks (Type A attacks), Prediction Procedures.
(nonpersistent agents), and For sea areas, the prediction of chemical downwind
- ground contaminating attacks (Type B attacks), hazard areas follows either the simplified, or detailed
(persistent agents). procedure.
Air contaminating Attacks (Type A attacks)—For The simplified procedure is intended for use on ships,
prediction purposes, two types agents are recognized— whereas the detailed procedure is designed for use in
- Type A.1— Sarin (GB) and all other known NBC Centers at Naval Headquarters, where trained NBC
nonpersistent agents, and personnel and suited facilities are available.
- Type A.2—Soman (GD) as an aerosol.
If the agent can not be identified, assume Type A. 1.
Ground contaminating Attacks (Type B attacks), Naval Chemical Downwind
(persistent agents): Message (NAV CDM)
After an attack with ground contaminating agents at The NAV CDM is computed essential in the same
sea, the hazard area will always be assumed to extend 10 manner as the land CDM. In most cases, the CDM
nautical miles (NM) downwind, when the representative information is obtained through land baaed NBC Centers.
wind speed is more than 5 knots. At wind speeds of 5 In the event, however, that land CDM information is
knots or less, the hazard area is assumed to be contained not available or differs significantly from the weather
within a circle with a radius of 10 nautical miles. conditions at sea, Figure 3-20 is used to determine the
The following delivery means are recognized– stability category. The numbers one through seven
- Artillery (ART), depicted on “the graph refer to the seven stability
- multiple rocket launcher (MRL), categories used in the land CDM.
- missiles/rockets (RKT), Once the stability category is determined, enter Table
- bombs, massive (BOM), 3-7 or 3-8 (page 3-24), depending on which agent was
- aircraft spray (AIRSPR). used, to determine the downwind hazard distance.
In cases where the means of delivery is unknown,
missiles are assumed.
Meteorological Data.
The meteorological data required for the downwind
hazard area prediction procedure is provided in the form
of a Naval Chemical Downwind Message (NAV CDM),

3-22
 FM 3-3

center point of the template circle coincides with the

center of the attack area and so that the value on the
protractor, corresponding to the downwind direction
given in the NAV CDM is oriented towards the north on
the chart. A sample template is at Figure 3-22.
Step 3. This position of the template is marked on the
chart by using holes punched in the template along the
downwind axis. The template is then moved back along
the downwind axis until the radial lines become tangents
to the circle (30 degrees standard). Use the holes punched
out along the radial lines to mark the position and connect
to circle, forming tangents.
Step 4. The maximum downwind hazard distance is
marked on the downwind axis. Through this point a line
is drawn perpendicular to the downwind axis, to intersect
the tangents (Figure 3-23).
When, in the NAV CDM, light or variable winds are
reported (wind speeds of 5 kts or less or variable wind
direction (999), the hazard area is represented by a circle
concentric to the attack area, with a radius equal to 15
NM.

Naval Chemical Downwind Naval Detailed Chemical

Hazard Prediction Downwind Hazard
Simplified Procedure Prediction
If a valid NAV CDM is not available, Figure 3-20 may The detailed procedure for prediction of chemical
be used to determine the air stability category, which is downwind hazard areas is designed for use at naval
the basis for the determination of the maximum headquarters, and leads to a more accurate prediction
downwind hazard distance. than does the simplified procedure. The detailed
This distance is determined from Tables 3-7 and 3-8 procedure is based upon the information compiled in the
(page 3-24). When using the simplified procedure, use “Chemical Prediction Data Sheet” (CPDS) and NAV
the downwind hazard distances related to miosis. NBC 1 or NAV NBC 2 Chemical Report. The CPDS <
The representative downwind direction and downwind Figure 3-3 must be filled in immediately on receipt of a
speed must be determined onboard the affected ship. new and updated CDM, and check on the receipt of a
Determination of NAV NBC 1 or NAV NBC 2 Chemical containing
meteorological information in letter items Y and ZA.
the Hazard Area The delineation of the hazard area resulting from an
The hazard area is determined as follows: attack with chemical agent requires information on the
Step 1. The center of the attack area (NBC 1 Chemical chemcial agent and means of delivery.
or NBC 2 Chemical letter item F) is plotted on the chart. Location of the attack area as reported in NAV NBC 1
A circle, the radius of which is 0.5 NM is drawn around or NAV NBC 2 Chemical Report
the center. This circle represents the attack area (Figure Representative downwind direction of the agent cloud
3-21). (taken from CPDS).
Step 2. A template for a simplified chemical hazard Maximum downwind hazard distance(s) related to
area prediction is place on the chart in such a way that the the appropriate hazard level(s) (LCt50) and/or ICt and/or

3-23
FM 3-3

3-24
FM 3-3

3-25
FM 3-3

miosis) (taken from CPDS).

Half-sector angle of the
hazard area:
35 degrees for wind speeds
higher than 5 knots, but less than
10 knots
20 degrees for wind speeds
of 10 knots and more.
For wind speeds equal to 5
knots or less, the hazard area
will be circular with radius equal
to the downwind hazard distance
for 5 knots wind speed.
However, the radius should not
exceed 15 nautical miles.
Determination of the
Downwind Hazard
Area.
Step 1. To plot the chemical
downwind hazard area on a sea
chart or on general operations
plot, the above information is
used in the following way (see
Figure 3-22).

3-26
 FM 3-3

Step 2. Plot the location of the attack area. If the exact concentric to the attack area circle, using the relevant
location (center of the attack) is known, draw a circle downwind hazard distance as the radius. However, the
around this point with a radius of 0.5 nautical miles. If radius should not exceed 15 nautical miles (see Figure
only a dissemination area is reported determine the 3-25.
center point of this area and draw a circle around this When wind speeds are 10 knots or more, the chemical
point, using a radius of 0.5 nautical miles. If the size of plot and subsequent NBC 3 Chemical Report would look
the attack area is known to be larger, the radius must be like that shown in Figure 3-26.
adjusted accordingly. If the meteorological conditions change within the
Step 3. From the center of the attack area circle draw period of duration of the hazard, the predicted hazard
a line, representing the downwind direction. area must be adjusted only if—The stability category
Step 4. Draw two lines which, being tangents to the changes from one category to another, and/or the wind
circle, form an angle equal to the half sector angle on speed changes by more than 5 knots or from 5 knots or
either side of the representative downwind direction less to more than 5 knots and vice versa, or the wind
(downwind axis). direction changes by more than 20 degrees.
Step 5. Label the point on the downwind direction line The hazard area is then determined as follows:
(downwind axis, thus marking the extent of the Calculate the downwind distance which the agent
downwind hazard distance(s) for the relevant level(s) of cloud may have travelled at the time the change in the
hazard LCt50 and/or ICt5 and/or miosis) and draw a line meteorological conditions occurred, by using the
through this (these) point(s), perpendicular to the representative downwind wind speed. Consider this point
downwind axis and intersecting the two tangents. The to be the center point of a “new” attack area, and draw a
downwind hazard area(s) is (are) contained within (these) circle around it with a radius equal to half the width of
line(s), the tangents and the upwind arc of the attack area the hazard area at that point. From there on, repeat the
circle. steps described earlier for determination of the
When low wind speeds or variable wind directions are downwind hazard area. The distance which the agent
reported in the NAV CDM, (wind speed 5 knots or less cloud may already have travelled must be subtracted
or variable wind direction (999)), draw a circle from the maximum downwind hazard distance under the
new weather conditions (Figure 3-27).
When a cloud from a chemical agent crosses the
coastline from sea to land or vice versa, consider the
point where the downwind direction line (downwind
direction line or downwind axis) intersects the coastline
to be the center point of a “new” attack area. Follow the
procedure described above, using the appropriate tables
for sea and land to determine the downwind hazard
distances. When frequent changes occur, use land
procedures when working manually.
In the case of air contaminating attacks, the beginning
and the end of the hazard at a certain location may be
determined from—the representative downwind speed,
the distance of the location from the edge of the attack
area, and the beginning and the end of the attack.
The following two formulas are used:
tB = (dµx 60) / (1.5 x VZ) or
tB = (dµx 40) / VZ and
tE = (Dµx 60) / (0.5 x VZ) or
tE = (dµx 120)/ VZ= 3 x tB
tB = time in minutes from the beginning of the attack
to the beginning of the hazard.
dµ = distance between the location and the downwind
edge of the dissemination area (in NM).
VZ = wind speed in kts. If necessary, the wind speed
must be determined as the mean wind speed over several
periods of validity of the NAV CDM.

3-27
FM 3-3

tE = time in minutes from the end of the attack to the for platoon through Brigade Task Forces. This checklist
end of the hazard. may serve as a guide for unit operations in a
Example: contaminated environment.
Given–alp = 5 NM, VZ = 10 kts.
Using the formulas, tn and tE are calculated as Vehicle Operations
follows— If agents have been used, soil particles become
tB = (5 NM x 40) / 10 kts = 20 minutes, and contaminated. When a track vehicle moves across the
tE = (5 NM X 120) / 10 kts = 60 miuntes surface and it’s movement causes these soil particles to
So, the beginning of the hazard is expected at this be suspended in the air, liquid droplets of chemical agent
location 20 minutes after the beginning of the attack and are also suspended in the air. The suspension of the
is expected to end 60 minutes after the end of the attack. chemical agent, therefore, becomes an increased threat
The expected maximum duration of the hazard maybe to follow on vehicles.
obtained by using the maximum downwind hazard
distance as d^, and calculating tE from the formulas.
The NBC agency (NBC Collection Center/NBC
Sub-Collection Center) must continuously check the
NAV NBC 3 Chemical Report issued, in order to ensure
that any new information (meteorological or NBC) is
considered.
If necessary, a corrected NAV NBC 3 Chemical
Report must be transmitted.

Avoidance Procedures
Once chemical agent hazard areas are plotted, units
may elect to by-pass suspected contamination or operate
within these areas. If the unit elects or is required to
operate within a contaminated environment, refer to FM
3-4 for performance degradation factors. Appendix A to
this field manual provides a checklist for CB operations

3-28
 FM 3-3

One of the basic tenants of crossing contaminated Helicopter Operations

terrain is to keep the contamination level as low as Helicopters flying over contaminated terrain may also
possible. Based on recent studies the distance that suspend chemical agents in the air increasing the risk to
chemical agents may travel when suspended in the air by aircraft following close or directly behind the lead
vehicle movement is depicted in Table 3-9. aircraft. Recent test results indicate that to avoid
The data presented in Table 3-9 represents the cross-contamination from the lead aircraft pilots should
distance in meters that chemical agent contaminated soil double the normal trailing distance between aircraft.
particles may travel, regardless of wind effects. When Further, according to these studies aircraft flying at an
track vehicles move across contaminated terrain, it is airspeed of 50 knots or more and at an altitude of 84 feet
possible that minute droplets of chemical agent, as small or higher (or an H/D of 2.0), above contaminated terrain
as 25 micrometers (urn), may become suspended in air may not receive an incapacitating vapor dosage of
and carried by the natural or vehicle induced air chemical agent inside the aircraft as long as all doors,
currents. These droplets may rise as high as 10 meters windows and vents are closed.
above the surface and extend downwind as far as 3 km. In the event that this altitude or airspeed cannot be
To reduce agent contamination trail vehicles should achieved or maintained monitor the interior of the
remain “button up” even if no vapor contamination is aircraft with the M8A1 Chemical Agent Alarm or the
detected while transversing terrain. Chemical Agent Monitor (CAM).
Units in the traveling formation may also encounter If the aircraft becomes contaminated, flying with the
cross-contamination to some degree if a lateral interval doors and windows open for approximately 15-20
sufficient to avoid dust from the side of the track vehicle minutes at approximately 90 knots, will reduce the
is not maintained. In the absence of cross winds a 50 contamination level by 95%. This may reduce the
meter spacing laterally is sufficient to avoid contamination level to such an extent that unmasking
cross-contamination. procedures may be initiated using the M256A1 Chemical
Agent Detector Kit.

3-29
FM 3-3

Chapter 4
Biological Agents
The avoidance of biological agents requires an thousands of virus particles, the cell is often destroyed
understanding of what biological agents are, how they as these particles are released. Viruses are much smaller
may be used, and what happens to them once they are than bacteria, ranging from 0.02 - 0.2 microns in size.
released. Units can then anticipate when and where Their small size means that a relatively small amount of
biological agents will be used. They can estimate where agent can infect a large number of personnel across a
the hazard is located so avoidance procedures can be wide area.
initiated.
Biological agents are divided into two broad categories Rickettsiae
— pathogens and toxins. Rickettsiae are bacteria that are unable to multiply
unless they are within a living cell. Most are spread
Pathogens from one person to another by means of an insect or tick
Pathogens are infectious agents that cause disease in that serves as a vector. The rickettsia will be picked up
man, animals, or plants. Agents that constitute by the vector from one infected person or animal, which
antipersonnel biological warfare (BW) threats include then transmits the rickettsia when it bites its next victim.
bacteria, viruses, and rickettsias (see Appendix B). Rickettsiae are smaller than most bacteria, but larger
These are commonly referred to as germs. While the than viruses.
vast majority of microorganisms are harmless or even
helpful, there are about 100 naturally occurring Toxins
pathogens that could be used as biological warfare (BW) Toxins are poisonous substances produced as
agents. Pathogens cause disease (infection) by entering by-products of microorganisms (the pathogens), plants,
the body through the lungs, digestive tract, through the and animals. Some toxins can be chemically
skin and mucous membranes of body openings. synthesized, and some can be artificially produced with
Once they enter the body, pathogens multiply, genetic engineering techniques. Toxins exert their lethal
overcoming the body’s natural defenses, and produce or incapacitating effects by interfering with certain cell
disease. All bacteria do not require living cells for and tissue functions. Basically, there are toxins that
growth. Symptoms most commonly associated with disrupt nerve impulses (neurotoxins) and toxins that
pathogen infection include upper respiratory flu or cold destroy cells by disrupting cell respiration and
like symptoms, vomiting, diarrhea, pneumonia or skin metabolism (cytotoxins). There is a vast range of signs
lesions (spots or rashes). Some pathogens, cause and symptoms with both toxin types. These signs and
nervous systems damage (headache, paralysis, symptoms can be confused with both chemical and
convulsions, or coma). pathogen poisoning.
The neurotoxins tend to be quick acting and produce
Bacteria nerve agent-like symptoms in seconds to hours.
Bacteria are living microorganisms. Unlike viruses Symptoms of neurotoxin poisoning range from mental
and rickettsias, they are capable of reproduction outside confusion, loss of balance, and vision problems to a limp
living cells. If they enter the body and if the victim is paralysis or convulsive-type seizures leading to coma and
not properly treated, the microorganism will multiply death.
and incapacitate the host. Bacteria can be found in An example of a neurotoxin is palytoxin, produced by
almost any environment. Those few that are potential a bacterium in palython soft corals. This is a fast acting
BW agents have the ability to rapidly cause illness after toxin causing muscle paralysis then death within 5
entering the body through the lungs or digestive tract. A minutes.
typical bacterial cell is 1-2 microns in diameter and 2-10 Cytotoxins tend to be slower acting and produce
microns in length (1,000,000 microns = 1 meter). choking, blistering, or even radiation-like symptoms in a
period of hours to days. Symptoms range from skin
Viruses lesions such as blisters, to vomiting, diarrhea, coughing,
Viruses constitute a large group of infectious and choking (the latter three signs may be accompanied
organisms. Unlike bacteria, they must be inside a cell in by bloody discharges) to marked weakness, coma, and
order to multiply. Viruses multiply by taking over the death.
cell, causing it to produce viruses instead of normal cell An example of a cytotoxin is trichothecenes (T-2
components. After producing hundreds or even

4-0
 FM 3-3, C1

toxin) which is a group of about 40 delayed acting. those around them. The extent of this hazard will vary
fungal toxins (mycotoxins). These are produced from from agent to agent, but it is an important part of
molds of infected grain and were reportedly used in controlling and avoiding further casualties. Also, the
Southeast Asia and Afghanistan in the 1970’s and coverage patterns of pathogen agent clouds are very
1980’s. T-2 toxin is often referred to as “yellow rain." sensitive to wind direction and speed. The enemy may
decide to use pathogens in an attack located close to their
own positions. In this case the enemy will be form-xl to
Characteristics of use a pathogen for which their troops have
BW Agents immunization, or the enemy must be willing to accept
some casualties.
Delayed Effects In general, healthy skin provides an adequate barrier
Both pathogens and some toxins - especially against most agents of biological origin. Skin (usually in
cytotoxins - can cause delayed effects. These effects a tropical environment) that has rashes, scratches, fungal
may take hours to days before the onset of disease. infections, etc . . . is more susceptible to skin penetrants.
The effects of pathogens are delayed due to the
required incubation period. This incubation period is the Skin Penetration
growth process of pathogens inside the body prior to Some toxins, due to their small molecular weight,
disease production and differs among agents. size, and solubility, may also penetrate the skin. MOPP
Toxins, unlike pathogens, are not living organisms gear protects the skin from the effects of such toxins and
The delayed effects are not caused by an incubation therefore must be used. For maximum protection and
period. The delay is caused by the time required to kill the lowest risk of incurring casualties, soldiers should
or inactivate cells. Repeated exposures to small amounts wear the protective gear for 4 hours after the unit has
(less than incapacitating or lethal effective doses) can been attacked or the agent cloud is predicted/known to
add up to an incapacitating or lethal effective dose. have passed through the unit area. During this time
every effort is made to identify the exact agent including
Large Area Coverage its characteristics.
Biological agents can be disseminated over large
areas. They cart sail with the wind and travel extensive
distances downwind. Pathogens can infect the target Weather Effects on
with as little as 1 to 20 microorganisms. Billions of Biological Agents
pathogenic cells can be packed in 1 gram of agent. The
light weight and small size allow these pathogens to Sunlight
spread easily to all areas that are not airtight. Similarly. Most biological pathogens and some toxins are
toxins are very potent and are more toxic than nerve affected by ultraviolet rays in sunlight. Most attacks will
agents. They require very low doses to exert their likely occur at night, during extended twilight, or during
effects. Toxins, like pathogens can cover large areas overcast conditions. To overcome this problem,
when disseminated. encapsulation (a natural or man made protective covering
around the pathogen), or possibly genetic engineered
Control pathogens, may produce agents that are resistant to direct
Somewhat more control can be achieved in employing sunlight. Thus. any agent delivered during conditions of
toxins as compared to pathogens and they can cover direct sunlight, or after beginning morning nautical
larger areas than those covered by chemical aerosols. twilight (BMNT), should be considered as a sunlight
Compared to the pathogens, they are extremely toxic and resistant agent.
lightweight, particularly if employed as art aerosol.
However, being chemical by-products rather than living Humidity
organisms, toxins are not infectious, contagious, nor The relative humidity that is the most favorable for the
capable of self- reproduction. Thus, area coverage and employment of a biological aerosol attack depends upon
the results of the attack are much more predictable and whether the agent is disseminated as a wet or dry
reliable. aerosol. For a wet aersol, a high relative humidity
Pathogens, however, are difficult to control: slows the evaporation of the tiny droplets of agent. This
especially if they are artifically disseminated. Because lowers the rate of decay of the wet agent because drying
some pathogens cause contagious diseases, the victim may result in the death of pathogens. On the other hand,
himself becomes the sourse of agent. Both sick and a low relative humidity favors the employment of dry
dead soldiers, and their wastes, can become a hazard to agents. The extra moisture present in the air when

4-1
FM 3-3

humidity is high may increase the decay rate of

pathogens in a dry aerosol. High humidity may also
promote a clumping of particles causing them to fall out
of the air more rapidly.
Wind
High wind speeds increase the area covered by
biological agents, but lower the casualty percentages
within an area due to dilution of the agent. Most BW
attacks will occur under conditions of moderate
windspeed, the most effective windspeeds for target
coverage being 12-30 kmph. As the agent cloud travels
downwind, it gradually loses its effectiveness due to
dilution caused by agent fallout, dispersal, and death of
the pathogen agent or neutralization of the toxin.
However, because most biological agents are lighter and
more potent (weight to effect basis) than chemical
agents, the downwind hazard areas of biological
weapons will be much larger than those of chemical
weapons. If delivered directly on target, as with a
bomblet attack, the wind direction and speed will have a expected to have little or no effect on hazard predictions.
more limited effect on coverage, however, downwind With the advent of toxins, bioengineering of pathogens
efforts must stall be considered. If dissemination occurs and encapsulation, even arctic or desert conditions are
far upwind from the target area in a more elevated much less restrictive to the user of BW. Most toxins are
manner, downwind effects can be even more dramatic. more stable than pathogens and are less susceptible to the
influence of temperature, relative humidity, and
Temperature Gradient radiation. As a general rule cool temperatures favor the
Temperature gradients may exert some effects upon employment of wet agents and warm temperatures favor
the behavior of a biological aerosol cloud. However, the employment of dry agents.
prediction of these effects require specific knowledge of
the agent and its potential carriers. The effects of Windows of Vulnerability
temperature gradient upon biological agents are similar Coordinate with higher headquarters, intelligence
to those upon chemical agents. However, because sources, and medical personnel to determine what
biological agents are effective in lower concentrations biological agent is most likely to be employed by the
than chemical agents, the effects of temperature gradient enemy. Determine, based on agent the optimum
are less upon a biological cloud than a chemical agent weather conditions and method of dissemination for
cloud. A stable atmosphere (inversion) results in the greatest effect for each agent considered.
greatest effects. Under unstable (lapse) and neutral Coordinate with the Divisional Staff Weather Officer
conditions, more atmospheric mixing occurs leading to a (SWO) to determine when these optimal weather
cloud of lower concentration, but still sufficient to inflict conditions are projected to exist m the Area of Operaation
casualties. Temperature gradients for biological agents (AO). These projected times that the optimal weather
normally are listed in Pasquill Stability Classes. These conditions exists is called “the wimdow of vulnerability”.
classes are listed in Table 4-1. As stated previously, This “window” represents the best time, based on
stable atmospheric conditions produce the best effects for weather, for the enemy to employ biological agents.
biological agents. This means Stability Class E or F. During this “window of vulnerability” if the unit is
The Simplified Biological Downwind Hazard Prediction attacked with something that appears to be a chemical
(SBDWHP) procedures will be used for all temperature agent; yet no chemical alarm or detector kit responds to
gradients. the agent, submit a Suspected Biological Report and
obtain samples.
Precipitation and Temperature
Precipitation will tend to wash biological agents out of
the air more rapidly. This will slightly reduce the Persistence of
downwind hazard. Most pathogens are stable at normal Biological Agents/hazard
temperatures, thus, the effects of temperature are The persistency of a biological agent refers to the

4-2
 FM 3-3

duration of effectiveness of the agent and varies greatly radiation has on reducing the body’s immune system.
between agents. They could also use pathogens before a planned
The persistency of a biological agent will depend on offensive maneuver. The maneuver would be timed to
many factors. Weather, terrain, ultra violet rays, coincide with the incubation period of the pathogen.
method of dissemination, and type of agent are just a few Troops in a weakened state due to the onset of illness
of the factors that contribute to the persistency of a will be more susceptible to fatigue, have slower reaction
biological hazard. These factors must be considered time, and will have their ability to make decisions
when determining or initiating unmasking procedures. hampered. This further reduces our capability to wage
The persistence of microbes can be enhanced by war. Biological agents can be used singularly or in
encapsulating them with a microscopic protective coat. combination with other biological or chemical agents.
In addition, some microbes will produce a very resistant This causes confusion in diagnosis, delays and
form called a spore. This is an essentially dormant state compounds treatment, and magnifies incapacitating or
which can reactivate when the proper conditions exist. lethal effects.
Spores will survive heat, drying and even some radiation U.S. forces may also be exposed to immediate and
for years. The spore can remain on the ground until residual biological hazards as a result of direct attack or
conditions become appropriate for the organism to by crossing biologically contaminated areas.
survive. In a process called reaerosolization, the Contamination avoidance is essential to reduce the
organism will be returned to its aerosol form by some impact of biological hazards. Our ability to survive,
outside means. The most probable scenario is that heavy fight, and win on a biologically contaminated battlefield,
vehicle traffic or winds will cause many of the organisms requires the capability for warning and detecting an
to be suspended in the air. This particle suspension will attack and identifying the agent. Detecting biological
cause a hazard area of military significance. The threat agent attacks are not easy. A detection/waming device
of casualties due to reaerosolization of the biological for pathogens is under development. An improved
agent is agent specific, but in most cases it will be below version of the M256 Detector Kit will be able to detect
5 percent. T2 mycotoxin. Future developmental items may include
Due to the sheer magnatiude of potential agents, the ability to detect biological agents with the on-board
persistency data, or decay rates for biological agents is mass-spectrometer for the NBC Recon System (FOX).
beyond the scope of this manual. Two biological agents For those agents that cannot be identified, detection is
with desirable weaponizing characteristics are Bacillus, accomplished by -
Anthracis, and Botulinum Toxin. Decay rate or Recognizing a pattern of employment to predict an
persistency rate graphs for these two agents are depicted attack.
in Appendix B, Figures B-1 through B-4. Using the IPB process with specific PIRs for advance
warning.
Use of Biological Agents Recognizing the signatory symptoms, signsg and
effects of biological agents.
Against US Forces Sampling with air samplers may provide indication of
It is possible that pathogens and toxins will be used an attack in progress.
against U.S. forces. The employment of pathogens and The first two methods of detection are the only
toxins throughout the entire battle area cannot be methods we have of warning troops of an attack before it
discounted. Possible targets of pathogens include: occurs. The last method will alert the unit that an attack
Rear area command centers and key facilities. has occurred, and therefore allow the unit to take
Troop assembly areas. necessary protection and decon procedures to minimize
Ports of embarkation or supply points, airfields and the effects. Additionally, this method will help to
industrial centers prior to the outbreak of hostilities. establish a pattern of employment and, during future
Possible targets of toxins include — attacks, it will give notice (or at least high suspicion) that
Forward combat areas and logistical areas. the enemy is employing biological agents. At this point,
Any area that presents a likely target for a terroist or it should be added that when a unit is attacked, the unit
insurgent group. can only suspect a biological attack. This suspicion is
The use of biological agents will complement the based on dissemination techniques, patterns of
effects of other weapon systems. For example, threat employment and the “window of vulnerability”.
forces could use pathogens with incubation periods that Confirmation of a biological attack occurs only when a
will cause the outbreak of disease, days or weeks after a sample of the unknown agent is obtained and laboratory
nuclear attack. This would maximize the effects analysis confirms that the unknown substance is

4-3
FM 3-3

biological in origin. Natural food poisoning can be caused by a bacterial

Prior to this laboratory confirmation, the unit will not toxin. But in such a case, the casualties would be
know if the attack was biological or chemical from an limited to those personnel that consumed the infected
unknown source. Mission Oriented Protective Posture food. This can be verified by a medical analysis. When
(MOPP) will protect the wearer against all known a biological agent has been used, large numbers of
chemical or biological agents. Therefore, the unit must soldiers are exposed at or about the same time. This
assume MOPP Level 4 (full protection) and apply those causes “explosive” epidemic numbers of casualties.
tactics, techniques and procedures (TTP) depicted in Criteria (signs, symptoms, and effects) for suspecting a
Appendix A for chemical or biological contamination biological attack include:
avoidance. Epidemic number of casualties occurring within
hours to three days of each other (most within 24 hours
Using Intelligence Sources of each other).
Intelligence can yield useful information for predicting Higher death or infection rates than normally
biological attacks. Intelligence also can yield encountered with the disease.
information that drives the scope and intensity of the Diseases or increased outbreaks of a particular
biological defense program. Combat, technical, disease not normally encountered in a particular region
medical, and strategic intelligence sources must be used. or country (for example, yellow fever in Europe).
Strategic intelligence gives the commander an estimate An aerosol dissemination technique is indicated by
of the threat force’s overall capabilities, limitations, and high numbers of respiratory signs—particularly when in
probable intentions for the employment of biological nature the disease affects the body through a different
agents. Combat intelligence gives the commander an portal of entry (such as pulmonary or lung-infecting
estimate of the threat force’s battlefield readiness to anthrax versus the much more common form of
employ biological agents. Technical intelligence enables skin-infecting anthrax).
evaluation of the effectiveness of enemy biological Multiple outbreaks of zoonotic disease(s) (diseases
agents, possible dissemination systems and of protective that are communicable from small animals to man).
equipment. Medical intelligence provides information Personnel working in a protected environment do not
about enemy preventive medicine, medical treatment, contract the disease (or vice versa could indicate a covert
types of potential pathogens employed and preparations dissemination of a biological agent).
in medically related areas that could indicate a possible Casualties occurring downwind, downstream, or
biological attack. See FM 8-10-8 for additional within a supply line pattern.
information on medical intelligence. Large numbers of sick or dead animals are observed,
especially if suffering the same symptoms of the disease
Recognizing a Pattern of Employment which is affecting the human population.
Using the IPB process, windows of vulnerability based The sudden appearance of large numbers of strange
on weather, enemy activity, and movement of likely insects or ticks that have not been encountered
dissemination systems. help characterize the patterns of previously in an area of operations. This information
employment. The time of attack, method of may be obtained through preventive medicine sections.
dissemination, type of munition used, or the stage of the Once suspected and reported, medical staff personnel
operation in which the agent is employed may be can conduct epidemiological studies and determine if
similar. Similar situations or patterns will not be definite there could be other causes for the outbreak and thus
proof that a biological agent attack is imminent but early prevent the perpetuation of false NBC reports.
warning should be given to all units in the potential
hazard area. Dissemination Techniques
Recognizing and Avoidance Procedures
Distinguishing Symptoms, To avoid a biological agent hazard, first; prevent the
Signs, and Effects attack and second, combat (limit) the effects on
Detecting a biological attack by this method is the personnel and supplies in the event of an attack.
least desirable way. But, due to the lack of detection The method of dissemination determines the extent
devices, covert dissemination, and delayed effects of and severity of contamination. However, some agent
biological agents, this may be the first indication of a specific defenses can be administered before the agent is
biological agent attack. With common diseases the disseminated. These defenses may take the form of
number of personnel affected gradually increases. immunizations or prophylaxis, (taking medicine oraly).

4-4
 FM 3-3

There are three general methods of disseminating initial formation) will travel downwind at a rate
biological agents. Each helps the agent to get into the determined by wind speed. The cloud will lengthen and
body. widen as it travels downwind. The length of the agent
Aerosol dissemination is used when the respiratory cloud will equal about one-third of the distance traveled.
system is targeted. Units near the release point will encounter a more
Vectors (such as fleas, lice, ticks, and mosquitoes) concentrated agent cloud. However, units located
and some toxins are used to attack through the skin. farther downwind (even though exposed to a less
Covert (hidden) methods are employed to attack both concentrated agent cloud) will be exposed for a longer
the respiratory and digestive systems. time, so unprotected personnel will inhale a higher total
dose. Figure 4-1 shows the typical downwind movement
Aerosol Dissemination Procedures and characteristics of a biological agent cloud. The peak
Biological agents may be disseminated by ground or danger area will be located in the area where the cloud
airbursting munitions, aircraft spray tanks, boat or truck stays in tact while at the same time is at its maximum
mounted aerosol generators. The attack most likely will width and length. This distance is approximately the
occur in a covert (or hidden) manner. Tactical level are maximum downwind hazard prediction for a chemical
those directed at specific units or elements on the agent; therefore, it is vital to determine whether or not
battlefield. They are likely to occur at altitudes of 1,000 the attack is biological or chemical. The biological agent
feet or less (100-foot optimum). Estimation of the hazard cloud can cause both immediate or delayed casualties.
areas resulting from dissemination at altitudes greater This is due to the fact that each individual will receive a
than 1,000 feet above ground level requires extensive different dose and the time until the onset of symptoms
meteorological analysis. Toxins can be disseminated as will be dependent on the amount of agent and each
a liquid (such as with “yellow rain”). This makes the soldiers physiological makeup. The onset of illness will
toxin highly visible; but the hazard will generally be also be affected by the soldiers reaction time and any
limited to the immediate area of the attack. other forms of protection (i.e inoculation, masking time)
In a tactical aerosol attack, the aerosol cloud (after that were available against the agent. Biological agent

4-5
FM 3-3

casualties can occur in an area as much as two times the form of attack is likely to take place as covertly as
maximum downwind hazard distance for a chemical possible. Tactical attacks (those directed at specific units
agent. Traveling farther downwind, the cloud is exposed or elements on the battlefield) with biological agents are
to environmental elements. It is subjected to dispersal likely to occur at altitudes of approximately 300 meters
and settling and impaction on terrain features. The agent or less. Determining the hazard areas resulting from
cloud will lose much of its concentration and the losses biological agent dissemination at altitudes of greater than
will be such that the majority of unprotected personnel 300 meters will require in-depth meteorological analysis
will not receive an infective (pathogen) or effective and is therefore beyond the capabilities of most units.
(toxin) dose. However, dispersal will not be uniform The simplified biological downwind hazard prediction
and casualties may occur as far as four to five times the (SBDWHP) pertains to aerosol disseminations that occur
maximum downwind hazard distance of chemical agents. at or below 300 meters above ground level, Biological
The following two examples illustrate biological aerosol agents may also be disseminated as a liquid (such as
strength: “yellow rain”) and the hazard generated by this means of
If the infective dose of a particular agent is one delivery will be limited to the area of attack.
organism and there is a concentration of just one
organism per 5 liters of air, the average soldier, Zones of Contamination
breathing at a rate of 15 liters/minute, can breathe in After its initial formation, the aerosol cloud will travel
three times the infective dose in one minute. downwind. The agent cloud will lengthen and widen.
It has been calculated that as little as 2 to 3 grams of While it is highly concentrated, it will cause a high
tularemia bacteria Francisella tularensis (causative agent number of casualties (immediate or delayed) among
of rabbit fever) may be sufficient to create a bacterial unprotected personnel (approaching 100% with some
aerosol 100 meters high and extending over an area 1 agents). The area in which casualties among unprotected
square kilometer. This can infect humans, breathing at a personnel will be high enough to cause significant
normal rate, with 100 minimum infective doses per disruption, disability, or elimination of unit operations or
minute. effectiveness is defined as Zone I. Priority medical
Knowing biological cloud behavioral characteristics, treatment may be required for individuals exposed to the
units may calculate the approximate cloud arrival time Zone I hazard. Units in this zone should increase their
and cloud exposure time. This provides both an protective postures during the period of greatest hazard
estimation of the exposure period as well as the time of or upon alert if near the attack area. Units should be
exposure if the point of attack has been identified. This able to calculate this period using the equations for cloud
information is presented later in this chapter. arrival and cloud exposure times.
There are two primary aerosol dissemination After traveling downwind, exposure to the elements
techniques: will disperse the aerosol cloud to a degree at which the
Bursting type munitions. majority of unprotected personnel will not receive an
Spray tanks/generators. infective (pathogen)/effective (toxin) dose. However,
dispersal will not be uniform, and casualties may occur
Bursting type munitions relatively far from the point of attack. This area of
When a biological projectile or bomb bursts on the reduced, but definable hazard is Zone II. Personnel in
ground or in the air, the filling (either a liquid slurry or this zone may assume a limited protective posture,
dry powder), is initially dispersed in all directions. including the protective mask, wearing work or
An effective ground bursting munition, will project protective gloves, buttoning up the uniform, rolling
the majority of the filling into the air to form an aerosol down uniform sleeves, and covering or bandaging any
cloud. Air bursting munitions may also form an aerosol exposed cuts or scratches. Monitoring of personnel in
cloud that will behave in a similar manner to a spray Zone II for symptoms/effects of BW agents is required.
attack. The agent may however, also be designed to fall Zone II includes all areas in which hazards to
to the ground as a surface contaminant much like unprotected personnel are likely to exceed negligible risk
persistent chemical agents. levels under an aerosol disseminated attack. This zone
The dimensions of the aerosol cloud will be influenced may be very large; under some conditions encompassing
by the means of delivery, the weather conditions, and thousands of square kilometers. Dividing the hazard
the terrain. areas into zones allows commanders to weigh the tactical
Spray Tanks/Generators considerations against performance degradation of
MOPP with some knowledge of the relative risks. The
Aircraft/vehicle spray tanks, or aerosol generators, end line for Zone I is the 20-30% casualty line and the
may also be employed to form an aerosol cloud. This end line for Zone II is the 1-3% casualty line. Figure 4-2

4-6
 FM 3-3

shows casualty probability curves for both Zone I and hygiene standards, and rest and nutritional needs of the
Zone II. It is important to note that the curves will be troops.
different for each agent and will depend greatly on the Gain intelligence on threat capabilities and intentions.
weather conditions that exist at the time of Seek out, intercept, and destroy enemy weapon
dissemimtion. systems, production facilities and storage sites.
Instruct troops on the threat and recognition of the
Aerosol Avoidance Procedures attack and protective measures.
Before the attack Train and drill on fitting and putting on protective
Establish and enforce preventive medicine programs mask and clothing.
to include immunizations, area sanitation and personal Set up collective protection systems for personnel,
equipment, and supplies. (NOTE: Field expedient

4-7
FM 3-3

collective protection must be airtight.) small cage vector bomblets can be used. The enemy
Identify backup (alternate) food, water, and supply may use vectors to circumvent the protective mask or
sources. MOPP gear. Any experienced field soldier or
Establish detection and sampling procedures. outdoorsman knows the the tick is capable of crawling
Conduct vulnerability analysis. under even the most constrictive clothing. Some flying
insects can travel considerable distances against
During the attack: prevailing winds. This makes dissemination patterns
Recognize the attack. hard to determine. Some pathogens can remain within
Initiate personnel protective measures. Masking is the infected vector for the life of the vector, so biological
the first priority, but since the attack may be chemical or hazards can be prolonged (one to two months for some
toxin, MOPP 4 is required initially. For maximum mosquitoes and six to seven months for some fleas). If
protection and the lowest risk of incurring casualties, the enemy decides to use vectors, control is a limiting
soldiers should wear protective clothing and mask for at factor. Of course, frigid temperatures that may kill the
least 4 hours after the unit has been attacked or the agent vectors, will also have an effect. This dissemination
cloud is predicted/known to have passed through the unit method also limits the enemy because he has no way of
area. Every effort must be made to identify the exact controlling the vectors once they have been released.
agent, including its characteristics. If the skin is Logistical and production problems can arise in the
contaminated, remove contamination immediately with delivery of a live pathogen inside a living vector in
large amounts of warm soapy water (if available) and sufficient quantities to be an effective weapon. The
decontaminate the skin with the M258A1 kit or M291 prediction of hazard areas caused by vector
kit. (FM 3-5, Chapter 2, has detailed instructions on dissemination is virtually impossible based on the
skin decon). unpredictability of the vectors.
Repulse or eliminate delivery vehicle or weapons.
Observe for distinguishing signs between biological Vector Avoidance Procedures
and chemical agent attack or a mixture of conventional Before the attack:
and biological attack.
Report the attack utilizing the NBC Warning and Apply insect repellant on exposed skin.
Reporting System (NBCWRS). (A biological attack that Gain intelligence on threat capabilities and intentions.
can not be immediately identified will be reported as an Seek out, intercept, and destroy enemy weapon
NBC 1, agent unknown or Suspected Biological Report). systems and production and storage sites.
Instruct troops on the threat, recognition of the
After the attack: attack, and protective measures.
Estimate the downwind hazard (significant casualties Establish and enforce preventive medicine programs
in unprotected personnel can be at least two times the to include immunizations, area sanitation, personal
maximum downwind hazard distance for a chemical hygiene standards, rest and nutritional needs of the
agent). troops.
Begin sampling/collection procedures IAW unit SOP. During the attack:
Consume only sealed rations and properly contained
water (outer container surfaces, if exposed, must be Recognize and report suspicious indications of the
properly decontaminated. See FM 3-5). Call preventive vector attack (the sudden appearance of large numbers or
medicine personnel when safety of unit level water strange kinds of insects not previously encountered in an
supplies are questionable. Ensure veterinary personnel operational area or the finding of vector bomblet cages).
inspect food storage depots and supply points. Replenish Cover exposed skin. Balance between protection and
water supplies from water purification units. degradation of performance. Protective overgarments
Separate biological casualties. Use minimum will not totally exclude the determined tick. Bloused
number of personnel (to limit exposure) to provide trousers and rolled down and buttoned sleeves with
supportive medical care until evacuation. insect repellant properly applied will probably afford as
much protection with less degradation.
Apply insect repellant liberally—especially to neck,
Vector face, ankle, and wrist areas.
Dissemination Procedures Report the attack.
Some pathogens may be delivered by use of After the attack :
arthropods and other vectors such as fleas, ticks, lice, The NBCC should coordinate with the supporting
and mosquitoes. Bulk container aircraft dissemination or medical authority for preventive medicine assistance.

4-8
 FM 3-3

Begin insecticide and other pest control measures as at-hand medical and intelligence information and analysis
outlined by preventive medicine personnel. Logistical of NBC 1 Reports.
support for unit-size pest control procedures should be a In conjunction with the veterinary and surgeon
coordinated effort between the NBCC and the supporting general initiate disposal and replacement of food, water,
medical authority. Physically remove body lice, ticks, and other supplies. The NBCC can coordinate
and fleas by self aid and buddy aid as necessary. inspections and medically approved replenishment
Make hazard estimates. Recon and medical reports sources. Actions involving disposal of major quantities
may help the NBCC in assessing hazard areas. of food must be coordinated with the supporting
veterinary personnel. Actions involving disposal of major
Convert Dissemination and quantities of other nonmedical supplies should be
coordinated with the NBCC.
Avoidance Procedures Initiate sampling based on knowledge, consent, and
Sabotage and terrorist personnel may possess a variety special sampling requirements of the NBCC. If a BW
of aerosol and contamination/poisoning techniques for attack is suspected, wash surfaces with at least a 5%
various targets. Aerosol techniques can be fairly large solution of bleach. Bleach is a very effective form of
operations, using aerosol generators (or foggers) that decontamination for most BW agents.
produce large open-air hazard areas. These techniques
also can be more limited and selective, targeting the Warning and Reporting
enclosed air space of key command and control facilities, Determining that a biological attack has occurred will
aircraft, ships, troop billets, and other similar type areas. pose considerable difficulties for soldiers. There are the
Biological agents in liquid, powders, or spray can be usual indicators of CB attack, such as low flying aircraft
placed directly into food stuffs at harvest, processing, spraying mists or fogs, munitions with little or no
distribution, and preparation points. They can be placed explosive effect, or ground generators spraying a fog or
into the water reservoir/distribution chain. mist, all during the “windows of vulnerability”. But
Before the attack: even if fortunate enough to observe the attack, the field
Maintain OPSEC. soldier will not be able to distinguish a biological attack
Identify covert/sabotage threat force capabilities and from a chemical attack.
intentions through intelligence. The NBCWRS is used to report biological attacks.
Arrange for security measures to be taken based However, the number of potential agents, the various
upon threat assessment. dissemination methods and techniques, and the lack of
Identify alternate supply sources for those high-risk automated detection and identification devices have
items. thwarted an all-encompassing simplified biological
Instruct troops to be alert to dissemination devices or hazard prediction. So, the use of the NBCWRS will be
signs of covert tampering as intelligence dictates. extremely limited. Until intelligence and prior
Establish and enforce preventive medicine programs experience come into play, it is unlikely that biological
to include immunizations, area sanitation, personal reports will go past the NBC 3 Report.
hygiene standards, and rest and nutrition needs of the Observed attacks will be transmitted (most likely) by
troops. (NOTE: Based on intelligence, protection of the NBCC as an NBC 1 Chemical Report, agent
food and water may prevent successful employment of a unknown or NBC 1 Suspected Biological Report. Upon
specific biological agent.) receipt of the initial NBC 1 Report, the NBCC will send
an NBC 3 Chemical Report.
During the attack: Reports from units in the immediate attack area will
Report the observation of an attack, the apprehension help determine the nature of the attack. The observation
of enemy agent(s) engaged in such activity, or the of two events in the attack may indicate a biological
finding of signs and indications of covert attacks. rather than a chemical attack. An attack that has no
Initiate personnel and collective protection. For apparent immediate effect on birds, animals, insects, or
maximum protection and the lowest risk of incurring unprotected personnel could indicate a pathogen attack
casualties, soldiers should maintain this protective or delayed action toxin especially if the attack occurs
posture for at least 4 hours. during the “window of vulnerability”. Observation of
After the attack : immediate effects coupled with a lack of
detection/identification of a chemical agent could
Warn personnel downstream, downwind, and/or indicate a rapid-acting toxin attack. This information
down supply lines. The NBCC will do so based on should be transmitted on a follow-up NBC 1 Report.

4-9
FM 3-3

The observations should be reported on line Zulu Bravo. report its data in an NBC 4 format with line Hotel
The report is then sent to all units in the division/corps specifying that the agent is unknown. Once the higher
operational area as an NBC 3 Suspected Biological headquarters receives confirmation of the samples
Report. In order to send an NBC 3 Suspected Biological contents they will transmit an NBC 5 based on the
Report, the NBCC will have to analyze the nature of the previous data from the submitted NBC 4’s. The final
attack as well as other information available. Presume NBC report is the NBC 6 Biological Report. It is a
that a biological attack has occurred based on the narrative description of biological attacks that have
following factors: occurred in the reporting units’ area of operation. It is
Analysis of NBC 1 Chemical Follow-up Reports. written at the battalion level or above. The NBC 6
Analysis of intelligence data regarding enemy Biological Report contains as much information as
capabilities, tactics, and activities. possible about the attacks. It is submitted only when
If attack occurs during the “window of requested and is sent hard copy. Figure 4-4 shows
vulnerability”. examples of biological reports.
Analysis of preliminary laboratory examinations or In some cases the NBCWRS may have to be modified
completed reports from past attacks (NOTE: Complete for a biological attack. This will occur when:
agent identification may take days or longer). The “windows of vulnerability” are present for the
precognition of a pattern of established warfare. optimum weather conditions.
Analysis of samples Observation of suspicious activity by the enemy
Onset of symptoms related to biological agents (e.g., low flying aircraft or generators emitting a vapor
Units use NBC 3 Suspected Biological Reports as or powder substance).
battlefield intelligence. With knowledge of the Area sampling teams, equipped with air samplers and
biological agent aerosol cloud characteristics, units can Elisa tickets as outlined in Chapter 5, in pre-planned
approximate the area in relation to the simplified positions obtain a positive sample or test for a biolgical
downwind hazard prediction of a chemical agent. Figure agent.
4-3 and 4-3a depict a flow chart for the agent When the conditions occur, the area sampling team
identification as it pertains to biological attacks. Figure will prepare an NBC 6 Suspected Biological Report and
4-3 represents the role of field units (Bn and below). send the report to the NBCC. The sample is evacuated
The process begins with the observation of a suspicious for laboratory analysis. The NBCC will:
attack. If the unit is unable to immediately identify the Plot the sampling teams position on the situation
agent they will then generate an NBC 1 Agent Unknown map.
Report (circle A, Figure 4-3). The NBC 1 Report is Prepare and disseminate an NBC 3 Suspected
forwarded to the NBCC (circle A, Figure 4-3a) and an Biological Report.
NBC 3 is generated assuming an unknown chemical After laboratory analysis confirms that the sample
attack. This NBC 3 is transmitted back to the field unit taken is a biological agent, the NBCC will determine the
(circle D, Figure 4-3a). The unit will receive the NBC 3 pattern of deposition and decay rate for the agent. This
Report (circle D, Figure 4-3) and take the appropriate may be accomplished by receiving other sampling
defensive measures. The field unit will continue to reports within the area, developing a pattern based on
attempt to identify the agent and will send an NBC 1 information gathered from medical or intelligence
follow up Report based on its findings for either a known sources, or by the simplified techniques for downwind
or unknown agent (circles B, Figure 4-3). The NBCC hazard prediction outlined in this chapter. Once this
will process the NBC 1 follow up Reports (circle B, area of deposition is defined by the NBCC, the NBCC
Figure 4-3a) and evaluate the data. If a biological attack will prepare and disseminate an NBC 5 Biological
is suspected the NBCC will issue an NBC 3 Suspected Report.
Biological Report (circle D, Figure 4-3a). The affected
unit will take the appropriate defensive measures (circle
D, Figure 4-3a) and plan and conduct sampling Principles of
operations IAW unit SOP (circle C, Figure 4-3).
Sampling should be conducted by trained personnel, Hazard Prediction
usually chemical infrastructure personnel trained in When a chemical or biological agent is employed as
sampling techniques. an aerosol, there will be an initial, lethal concentration
After a unit (Bn or lower) receives an NBC 3 of agent in the area employed. The agent will form a
Suspected Biological Report from higher, they may be cloud that will be carried downwind, spreading at a 30
directed to perform a sampling operation. The unit will degree angle to either side of the wind direction. The

4-10
FM 3-3

4-11
FM 3-3

4-12
 FM 3-3, C1

wind will then carry the agent and dissipate it. The can be found from the cloud exposure time (CET), the
length of the cloud is approximately 1/3 of the total total time that a unit will be within the cloud. CET is
distance traveled. As the cloud increases in width and calculated by:
length, the actual exposure hazard will increase, because
although the concentration of the cloud has decreased the CET = cloud exposure time (in hours)
exposure time will be greater due to the increased size of CET = distance (km] from attack wee
the cloud. Therefore troops will be exposed to a lower
concentration of agent, but for a longer period of time. 3 x windspead (kmph)
The cloud is expected to produce at least a 20% casualty
rate for exposed, unprotected troops in Zone I. In time,
the cloud dissipates (and the agent degrades) to the point Simplified Downwind
at which it can no longer produce casualties. In Zone II,
the casualty rate for exposed, unprotected troops is less Hazard Prediction for
than 20%, but greater than 1-3%. Beyond Zone II, less Biological Agents
than 1-2% of exposed troops are expected to be
casualties. There are three questions of tactical (SBDWHP)
importance to both commanders and troops in the field Downwind hazard prediction for biological agents is
1. Will personnel be exposed? A prediction of this is very similar to the produre for chemical agents. The
Zone I and II areas defined by the SBDWHP. resulting prediction provides a minimum estimate of the
2. At what time will troops be first exposed to the danger zones for biological agents in general. After
agent? This can be found from the cloud arrival time employment, actual sampling by trained personnel will
(CAT), the time when the aerosol cloud will first reach a produce a better indication of the areas affected.
unit. CAT is calculated by: Indications of a biological attack: You should suspect
CAT = cloud arrivat time a biological attack when 1) there are indications of a
TOA = time of attack chemical attack, but no effects, and 2) a presumed
CAT = TOA + Distance (km) from attack area chemical attack has occurred, but the agent has not been
identified. In the first case, soldiers would observe such
windspeed (kmph) enemy activities as low flying aircraft or generators
3. How long will troops in the area be exposed? This spraying mists or fogs, or munitions detonating with
little or no explosive effect. There would be no

4-13
FM 3-3, C1

symptoms of a chemical attack, however. In the second Being Morning Nautical Twilight (BMNT)
situation, there would be the effects of a chemical attack
such as casualties among unprotected troops, but the Cloud Duration of the
agent cannot be identified with standard detection Greatest Effects (Zone 1)
equipment. Engineered/Hardened Pathogens
Nonherdened Pethogens # of hours from time of
In both cases described the unit observing the attack attack to BMNT + 2 hours.
will submit an NBC 1 Chemical Report, agent unknown, Max 8 hours.
Toxine 8 hours
to the NBCC. Soil, liquid, and surface samples should Type A Case a (point Source Attack and Toxins)
be collected and sent to servicing identification All attacks that occur during daytime and all toxin
laboratories as quickly as possible, when directed by the attacks will be presumed to have a cloud duration of the
NBCC. greatest effects of 8 hours. Only for night attack is it
Upon receipt of the initial NBC 1 Chemical Reports, necessary to compute this duration.
the NBCC will issue an NBC 3 Chemical Report to alert The 8 hour maximum for cloud duration is based upon
units m the immediate downwind hazard area. The NBC agent decay by environmental conditions, particle fall.
3 Chemical Repro-t equates to approximately 50% of the and cloud dissipation. The actual effectiveness to minium
Zone I of the Simplified Biological Downwind Hazard hazard levels may extend to as much as 32 hours. [Four
Prediction (SBDWHP). This warning will be adequate times (4X) the cloud duration of greatest effects.]
for the first 1 to 5 hours (dependent on windspeed); the 1. Derive the location of the attack from NBC I
units in the remainder of Zone I and Zone II of the Chemical Report and plot the” location on a map or
biological hazard will need to receive an NBC 3 template.
Biological Report for adequate warning. 2. Draw a 1 km circle around the point of attack.
The hazard area prediction will be less reliable as the 3. Determine the maximum Downwind hazard
distance and time from the point of attack increases (If (MDWHD)
the wind changes, follow the same procedures for MDWHD = 4 x Windspeed (kmph) X Cloud
recalculation as for chemical hazard prediction. Duration* of greatest effects (Zone I)
Units in the downwind hazard area will not be able to * The cloud duration is a measure of the length of
detect arrival of the aerosol cloud. Thus, no NBC 4 time a biological agent is likely to remain effective and
Biological Reports will be generated. Downwind units aerosolized in the environment.
should collect soil, liquid and surface samples at various 4. Draw a line from the point of attack along the
times following calculated cloud time arrival, as directed representattive downwind direction, equal in length to
by by NBCC. These samples will be handled through the MDWHD (example #4, step 4).
the technical intelligence chain. This will allow 5. Draw a line perpendicular to the representative
determination as to where the downwind hazards actually wind direction, intersecting the point of the MDWHD
occurred. (example #4, step 4).
Due to the infectious nature of pathogens, close 6. Extend the line along the representative wind
co-operation and coordination between medical and direction for a distance twice the radius of the circle
maneuver units will be required to limit and control the around the attack area from GZ in the direction behind
effects of biological attacks. Biological agents could be the attack area (example #4, step 5).
reaerosolized by vehicle traffic, etc., in the downwind 7. From the rear endpoint of the representative wind
hazard area, especially Zone I. direction line, draw two lines that intersect this point,
Hazard Prediction are tangent to the attack area circle, and intersect the line
Three kinds of Biological attacks will be discussed. of MDWHD (example #4, step 6).
a. Type A Case a: a point-source attack (ex: aerosol 8. Erase the area behind the attack area circle. The
generator, bomb) or an area attack (as in artillery or remaining area constitutes the Zones I & II hazard area.
bomblet attack). This type of attack is also used for The points shown on the diagram define the hazard area.
toxins. Indicate these points on line PA of the NBC 3 Report.
b. Type A Case b: a spray-line. 9. Divide the MDWHD by 4. Plot this distance along
C. Type B: A large liquid drop/ground contaminating the representative wind direction line. Draw a line
attack. perpendicular to the representative wind direction and
The following information is required: which intersects both tangent lines at this point. The area
NBC 1 Chemical (Initial report will indicate within this smaller plot is the Zone I hazard area
unknown chemical) (example #4, completed diagram).
Chemical Downwind Message Example of full downwind hazard prediction (see

4-14
 FM 3-3, C1

diagrams for step by step solution). Type A Case b (linear spray)

10. Report the two points at which the Zone I hazard 1. Derive the location of the attack area from NBC 1
line intersects the tangent lines on line ZB of the NBC 3 Chemical Report. (A number of reports may need to be
Biological Report. evaluated). Plot the attack area or spray line on the
map. Draw a line through the attack area from the start
point to the end point (example #6, step 1).
2. Draw a 1 Km circle around the beginning point
and endpoint of the spray line (example #6, step 2).
3. Determine the MDWHD, as in Case a.
4. From each endpoint of the sprayline, draw a line
equal in length to the MD along the representative
downwind direction (example #6, step 3).

Type A Case a (area attack)

1. Derive the location of the attack from NBC 1
Chemical Report and plot it on the map.
2. Plot a circle with a radius of 1 Km, unless the
attack area radius is known to be more than 1 Km. If
the attack area is known to be greater than 1 Km, then
plot a circle with a radius equal to the radius of the
attack area around the center of the attack area. The
circle must have a minimum radius of 1 Km.
3. All subsequent procedures are exactly as outlined
in Type A Case a point source sample. (See diagrams
for Step by step solution).

4-15
FM 3-3, C1

circles. Erase any area behind the attack circles. This

figure encompasses the Zone II hazard area. Report the
points delineating this area. (See figure on line PA of
NBC 3 Reports (example #6, step 6).
9. Divide the MDWHD by 4. Plot this distance from
the attack area endpoint furthest downwind on the
representative wind direction line. Draw a line
perpendicular to this point which intersects both tangent
lines. This smaller figure is the zone I hazard area.
Report the point of intersection with the tangent lines as
Zone I on line ZB of the NBC 3 Biological Reports
(example #6, step 6).
Example 6: Time of Attack 0930 (See diagram for
step by step solution).
BMNT: 0700
wind speed: 12 Kmph
wind direction: 90 deg grid
spray length: 10 Km
MDWHD=4x12x8=384Km
Type B (Large Liquid Drop/
Ground Contamimting Attack)
1. Derive the locaation of& attack area from NBC 1
Chemical Report and plot it on the map.
2. Draw a circle with a radius equal to the radius of
the attack area. This circle should have a minimum
radius of 5 Km.
3. Report the hazard area as rhree digits on line PA of
NBC 3 Biological Report.

Sampling
Sampling aids in the identification of an agent and
enhances determinaion of medical treatment required.
Obtain a large amount of agent relatively free of
interfering rnaterials. Sampling identfies which agents
were used in an attack. Identification can aid in -
Confirming that an attack has taken place.
Determining the proper therapy for personnel
exposed to the agent.
Estimating the possible number and type of
casualties.
5. Draw a perpendicular line intersecting the Determining the time-to-casualties if time of the
MDWHD point on the representative wind direction line attack is known.
drawn from the attack area endpoint furthest downwind Evaluating an enemy’s biological capability.
(This is the line of Maximum Downwind Hazard - Sampling should be conducted by trained personnel.
example #6, step 4). (These are chemical infrastructure and NBC recon
6. Extend each representative wind direction line 2 personnel specifically; but by prior coordination in SOPs
km behind each endpoint of the spray line (example #6, and OPLANs, intelligence or medical technical
step 5). assistance and/or specific advise could be rendered.)
7. Draw a line from each point 2 Km behind the Trained personnel ensure uniformity, viability, safety,
endpoints tangent to the outer side of each circle. until it and accountability in sampling procedures. Sampling is
intersects the MDWHD line. (example #6, step 6). not done indiscriminately, but only when an attack is
8. Draw a line tangent to the rear of both attack indicated. Sampling operations, other than medical

4-16
FM 3-3

4-17
FM 3-3

4-18
 FM 3-3

pathological sampling will be initiated only upon the

knowledge and consent of the NBCC. Sample priorities
are bulk agent and delivery systems, first environmental
(contaminated vegetation, soil, water, and clothing),
second; and biomedical (patient or autopsy tissue, urine,
and sputum) samples, third.
The standard sampling kit is the M34 CBR agent
sampling kit. This kit contains material necessary to
obtain small liquid and solid samples. Directions for its
use are contained in TM 3-6665-268-10. Additional
sampling operation guidance is as follows:
If the M34 kit is not available, a field expedient kit
can be assembled from like materials with the help of
supporting medical units.
Hand-off points, sample couriers, special packaging
and handling procedures, chain of custody, and
diagnostic laboratory delivery points should be
coordinated and specified in SOPs/OPLANs. Otherwise,
the NBCC will have to coordinate and specify
requirements between medical, intelligence, recon, and
decon units not previously coordinated (along with any
special requirements dictated by the situation).
Commanders will ensure priority sample transport to
diagnostic laboratories.
Trained medics, intelligence, or chemical personnel
should be utiliized as sample couriers.
A strict chain of custody must be maintained. This
allows samples to be traced to their origin.
Sample data must accompany the sample.
A1l samples will be in double containers to prevent
leakage during transport.
Detailed sampling techniques are further described in
FM 3-19, NBC Reconnaissance.
Evacuation of Biological Samples
Biological samples must be evacuated to the
appropriate laboratory facilities for confirmation of a
biological attack. Under normal circumstances labs will
be established in the theater of operations to minimize
confirmation time. CONUS Labs will also be utilized to
verify the results of the theater labs. This information
will then be disseminated to subordinate units to ensure
that adequate protective measures are implemented for
protection of both civilian and military personnel.
Confirmation of an enemy biological attack will also be
reported to the National Command Authority (NCA) for
a decision concerning the appropriate military and
diplomatic response. Figure 4-5 shows the standard
chain of custody for the evacuation of biological
samples.
Biological sampling and detecting on board ships
follows the same format as described in this chapter
except samples will be sent to the Navy Forward
Laboratory for the area concerned.

4-19
FM 3-3

4-20
 FM 3-3

Chapter 5
CB Reconnaissance, Monitoring, and
Survey: Planning, Conducting, Recording,
and Reporting
Chemical and Biological (CB) reconnaissance,
monitoring, and survey may be divided into two main Reconnaissance
categories; chemical and biological operations. Recon is searching for chemical hazards in an area
before a unit moves into or through the area. All units
use reconnaissance to locate chemical hazards. CB
Location of Chemical recon techniques are similar to conventional recon
Agents techniques.
Before moving into or occupying an area, units check
Chemical downwind hazard prediction in Chapter 3 the area for enemy activity and the presence of chemical
provide a means of locating probable chemical hazards. hazards. When in a static position, units recon areas
Before units can avoid chemical agents, they must know around their positions. The recon team or element may
what type of agent is present and where it is located. have an Automatic Chemical Agent Alarm, CAM, M256
Nonpersistent agents are present as a vapor hazard Series Detector Kit, ABC M8 Paper, M9 Paper, M272
(except in and around the shell crater). Persistent agents Water Test Kit, and M34 Sampling kit. Division recon
are present as both a liquid and vapor hazard. Liquid elements may also be equipped with the M-93 NBC
agents are usually found in the attack area. Vapor Reconnaissance Vehicle (FOX).
hazards are in both the attack and hazard area.
Vapor hazards are the most difficult to predict. They Procedures
may arise from an agent delivered as a vapor or from Recon procedures are the same regardless of who
evaporation of a liquid chemical agent. The chemical conducts them. The purpose of CB recon is to find the
downwind hazard prediction, described in Chapter 3, boundary of contamination and/or routes around or
outlines the largest area vapor could travel. Within that through a contaminated area.
prediction, there are both clean areas and areas where Recon teams determine the following information:
chemical agent vapor still linger. Although computer Are there chemical agents present?
modeling of the terrain and weather conditions would If an agent is present, what type of agent is it?
provide a better picture of where chemical agents may Where and when was the agent first detected?
go, it does not preclude sending a soldier to that specific What are the boundaries of the contaminated area?
location to verify whether or not the agent in question is Is there a clean route through the area?
there. To accomplish this, units may use the Automatic The unit commander then uses this information to
Chemical Agent Alarm (M8A1), the Chemical Agent form a picture of what chemical agents are in the area of
Monitor (CAM), and the M256 Samplers/Detectors to operation. This is used to plan future operations.
locate vapor hazards. FM 3-4 describes in greater detail Prior to leaving the unit area to conduct the recon, the
how weather and terrain affect where chemical agent recon team prepares its equipment and determines areas
vapor will exist. of priority. Areas of priority include possible movement
The location of liquid chemical agents is much easier routes and possible unit locations. The unit commander
to predict because wind and terrain do not affect their designates an area for the recon team to return for
location. It takes significant weather such as a heavy decontamination.
rainfall to move liquid chemical agents. They The recon method used depends on the tactical
decompose through weathering; liquid agents usually situation and the need. The following paragraphs
will evaporate from exposed areas and collect in describe recon procedures and what decisions must be
sheltered areas. Units use ABC MS or M9 Detector made. Units adapt these procedures to fit their own
Paper to detect liquid hazards. Recon, monitoring, and need.
survey methods are used to locate liquid and vapor The first step is to plan the recon. The unit
hazards. commander indicates areas of priority and determines
approximate distances between recon checks. The

5-1
FM 3-3

distance depends on the tactical situation, time available, If time is not critical, or if radio assets do not permit
and future use for the area. Distances are less in areas passing the information over the radio, the information is
that the unit might move through or occupy. Figure 5-1 recorded and carried back to the unit. The chemical data
shows an example of how priority areas are designated. sheet is used to record and transfer recon information.
Initially the recon team conducts checks at 500-meter Figure 5-2 shows a completed DA Form 1971-2-R
intervals. They concentrate on areas where chemical (Chemical Data Sheet-Monitoring or Survey).
agents will collect: low spots, small valleys, and
sheltered locations. For more information on where Monitoring
agents may collect, see FM 3-6.
The recon team uses the CAM and the M256A1 Series All units use monitoring to determine if a hazard is
Chemical Agent Detection Kits to detect vapors and still present. Monitoring can be done on personnel,
ABC M8 or M9 Detector Paper to check for liquids. equipment, or terrain. Basically it is a recheck to see if
When time is critical, use sampler/detectors only when a contamination hazard, identified by a recon team or in
necessary. If the CAM and M256A1 samplers/detectors detecting an attack, still exists. The purpose of
are not used, commanders must realize there is a risk of monitoring is to enable the commander to decide the
contamination and units must conduct liquid tests as they protective posture of the unit. If monitoring reveals no
move through the area. hazard, then the units may lower their MOPP level
When the team detects chemical agents, they change (depending on the threat workload). The M256A1
procedures. They mark the area (unless ordered Detector Kit is the primary piece of equipment used to
otherwise). Then they move back to a clean area. monitor for chemical agents. This kit, supplemented by
They then move laterally for a predetermined distance the CAM, M8A1 Alarm, and ABC M8/M9 Detector
(usually 500 meters), then move forward again. This Paper provide the monitor with the necessary equipment
procedure is followed until they reach the unit boundary to detect the presence of chemical agents. If monitoring
or find a clean route through the contamination. reveals that the chemical agent is still present on
equipment, decon operations may be required.

Surveys
Chemical surveys are required when the
commander needs detailed information on the
size of a contaminated area. Unlike radiological
surveys, the intensity of chemical contamination
cannot be determined. Learning the extent of
contamination within the area of interest and
along specific routes is the primary interest.
Recon elements find the contaminated areas.
The unit conducting the chemical survey usually
knows the general location of the contamination
and what type agent to expect. It may also
know how the agent was delivered. This helps
when planning the survey.
Recording and Reporting For example, an area contaminated by an artillery
attack usually is smaller than an area contaminated by a
RECON Information spray attack. This information determines the number of
The method the recon team uses to report information recon teams needed and the amount of time needed to
depends on how urgently the information is needed. If conduct the chemical survey.
time is critical, the information is passed over the radio Time is a major factor in planning and conducting
using the NBC 4 Chemical Report format: chemical surveys. Each detection test requires time.
Standard Format The primary concern in surveys is to determine areas
NBC 4 Chemical contaminated by persistent chemical agents, so the
H Nerve, V majority of the testing done during a survey is with M8
Q LB195300, Liquid or M9 Detector Paper. Periodic tests are done with the
S 201050Z M256A1 Detection Kit to ensure that only the chemical
agent being tested for with the detection paper is present.

5-2
FM 3-3, C1

5-3
FM 3-3, C1

When conducting a chemical survey, there are several

Possibilities that must be considered: what type agent is
known to be present, is there a chance for a mixture of
agents, and how much time is available to do the survey.
The most important aspect is to do a thorough job. If a
hazard is missed, the unit could sustain casualties when
they occupy the area. Figure 5-3 gives an indication of
how long surveys take.
The size of a contaminated area is important, in
determining the number of teams needed to conduct the
survey. Use the following table to estimate the size of
the attack area for planning purposes.

If the agent identified by the detector kit is also

detectable with ABC M8 or M9 Paper, perform all
subsequent tests with detector paper. This will reduce
the time required to perform the area survey.
The NBCC provides each survey team with an overlay
showing the area to be surveyed. It also shows the
Techniques initial test points for each survey team. Figure 5-5
Three techniques are used to conduct chemical surveys. shows the initial and subsequent test points for one
They are route, point and area surveys. Routes and specific survey team. The Figure also shows how teams 1
points may be surveyed if that information is needed. If through 4 are equally spread out so that the chemical
conducted, the survey team goes to a specific point or survey teams cover one forth of the survey area. Each
points along a route and test for the presence of liquid team tests with the detector kit at the initial testing point.
contamination with ABC M8 or M9 Detector Paper. Detector paper tests are taken every 200 meters until the
The area survey is used to determine how large an area agent reacts with the paper or until each team member
is contaminated. This information is used to determine comes to within 200 meters of the attack center. All
whether to bypass or cross through the contaminated area. team members will exit the area by the route used by the
Area surveys can also be used to find relatively clean areas vehicle operator.
or clean routes within a contaminated area. If only one survey team is used, the survey team
Figure 5-5 shows the basic concept used for conducting repeats the above procedures for each sector. If more
en area survey. In this illustration, the attack has a then one team is used, the NBCC identifies each team’s
1-kilometer target radius. The basic procedure applies to starting points (SP).
any target radius.

5-4
 FM 3-3

Chemical Report. It usually is sent as an overlay.

Figure 5-6 shows an NBC 5 overlay with required
marginal information. If time and distance do not
permit, it can be sent as a NBC 5 Chemical Report.
Figure 5-7 is an example of an NBC 5 Chemical Report.

Recording and Reporting

Procedures
Record results of a chemical survey on a DA
1971-2-R Chemical Survey Data Form. The important
information is the type of agent, the location where it
was detected, and the type of test taken. Figure 5-2
shows a completed Chemical Survey Form.
The method used to report the chemical survey results
depends on the situation. Since chemical survey reports
are lengthy, the information usually is not transmitted
back to the NBCC. The completed data sheet is carried
back and handed to the NBCC. If time is essential, the
information can be sent over the radio net. If this is
done, the information is transmitted in an NBC 4
Chemical Report format.

Operational Aspects
Recon locates contaminated areas, monitoring finds
contamination on personnel and equipment, and surveys
confirm and define contaminated areas. These areas
must be marked as contaminated. Use the NBC
Contamination Marking Set described on page 5-9.
Once located, the coordinates of the contamination areas
are plotted as an overlay on the situation map. Units use
this contamination overlay to plan operations. Note: The coordinates in line Xray must be sent and
Commanders determine routes and unit positions, and plotted sequentially. If line XRAY’s beginning and
plan tactical operations based on where the ending grid coordinates do not match, this means you
contamination is located. If unable to avoid the area, have an open area of contamination.
commanders determine routes of least contamination and Another method used to pass information about a
determine what protection is required. They also choose chemical attack is the NBC 6 Chemical Report. It is
locations for individual and unit decon sites on the other especially useful for a unit just arriving in an area of
side of the contamination area. operation because it gives a summary of the chemical
Information on where NBC contamination is located is activity in that area. Figure 5-8 is an example of an
passed from one unit to another using the NBC 5 NBC 6 Chemical Report.

5-5
FM 3-3

a tailored detection capability in those tactical

situations where it is impractical to employ
remoted point samplers, such as the M8A1 system.
This would be done when the need for operational
security, emplacement/recovery time/workload
requirements, and some operational risk is
acceptable. The mission may be conducted while
mounted in the M93 Reconnaissance Vehicle or
dismounted (using the XM21 Remote Alarm,
M8A1 Alarm, and the M256A1 kit) configuration
based upon the situation and the support unit.
Reconnaissance (NBCRS Mounted)
The reconnaissance mission is conducted to
reduce the time required to perform NBCRS
primary mission or to increase confidence that an
area is uncontaminated. In a typical mission
supporting NBC reconnaissance, an additional
team may be used to monitor a portion of a route,
that has been previously checked and classified as
uncontaminated by the NBCRS. While the
NBCRS is checking an adjacent route, a task
organized team equipped with an M8A1 Alarm,
XM21 Alarm, CAM or ICAD may overwatch the
area just checked to report if a munitions event
occurs following recon and prior to use of the
Point Surveillance, route by the maneuver force.

Area Surveillance, and Division NBC Center

At the Division, brigade mission support request are
Reconnaissance received by the NBCC and compared with division
The following chemical surveillance measures and requirements to ensure that there is no redundancy.
reconnaissance techniques may be recommended by the These request for support are weighted against the
staff chemical officer to support the scheme of Division Commander’s concept of the operation and a
maneuver: priority is assigned. The Division Chemical Officer then
provides a proposed course of action to the G3 designed
Point Surveillance to accomplish hazard avoidance for the division.
The point surveillance mission is conducted for a
specific period of time, oriented to key terrain. It is Mission Management
typically conducted to ensure that time sensitive or Mission management is the direction and control of
critical operations can be conducted without unwarned hazard avoidance operations. It involves identifying and
encounters with chemical agent clouds or transfer planning necessary actions for satisfying each identified
hazards resulting from a munitions event. For example, requirement. Mission management at the division level
use an M8A1 alarm or an XM21 on a ridgeline oriented is accomplished by the NBCC. This section prepares the
upon a bridge or on a other identifiable choke point up division hazard avoidance plan and coordinates it with
or down a valley. The principle advantage of this the division reconnaissance and surveillance plan that is
employment technique is that it capitalizes upon the developed by the G2.
strengths and minimizes the weak points of the detector.
The XM21 is best used where a heavy agent vapor Contamination Marking
concentration of short-to-medium size will be seen Once contamination is found, mark the area and-report
within the entire field of view of the detector. to higher headquarters. Marking contaminated areas and
Area Surveillance equipment warns friendly units and helps them avoid the
The goal of the area surveillance mission is to provide contamination. Marking a contaminated area merely
indicates the presence of a hazard. The extent of a

5-6
 FM 3-3

hazard is determined by a detailed survey. these contamination markers on poles. These poles may
be camouflage support poles, extra tent poles or any
Standard Signs other such material. The intent is to raise the
Signs used for marking contaminated areas are contamination marker up high enough so that it can be
standard throughout NATO in color and size. This seen for at least 200 meters. This is done so that
permits easy identification. The color of the sign follow-on forces and support troops can be aware of the
indicates the type of contamination. The primary or hazard.
background color indicates the general type of hazard. In these rear areas, “clear areas” or “lanes” may also
The secondary color gives specifics as to what the hazard be marked for easy identification. One method of
is. Figure 5-9 (page 5-8) describes the various signs, marking this lane is using the CB Contamination Bypass
their colors, and required data. Marker depicted in Figure 5-11 and 5-12 (page 5-10).
In addition to color, signs are also a standard size and NOTE: Placing markers on poles, or using the
shape. The sign is a right-angled isosceles triangle. The bypass marker in forward areas is considered tactically
base is approximately 28 centimeters (11-1/2 inches) and unsound and should be avoided. It would only provide
the sides are approximately 20 centimeters (8 inches). a roadmap for the enemy.
The signs can be made of wood, plastic, metal, or any
other available material. Place the signs with the point Marking Contaminated Materiel
of the triangle facing down. Special procedures are used when marking and
For biological contamination and for persistent or handling contaminated materiel. Materiel is marked to
semipersistent chemical agents, you need the type of keep personnel from accidentally becoming
agent (if known), date and time of detection. contaminated. This means that markers placed on
The United States marks contaminated areas with the materiel have to be visible from any angle. The
NBC Contamination Marking Set. It contains everything disposition of the materiel depends on the situation. If it
needed to mark a contaminated area - flags, ribbon, can be left in place to weather, that might be the best
crayons, mounting stakes, and a carrying container. TM solution. If contaminated materiel is collected in a
3-9905-001-10 describes the kit and its use. Figure 5-10 holding area, then the area has to be marked and
(page 5-9) shows the kit and its major components. monitored for residual hazards. Since vapor hazards are
If units do not have this kit available, they can make additive, several pieces of like contaminated equipment
the signs out of available metal, plastic, or wood. These together could create a serious vapor hazard when
field expedient signs must be of standard shapes, sizes, located near each other. This could be a problem in
and colors. areas such as maintenance holding areas.
Since residual hazards can collect in inaccessible
Marking Procedures places, contaminated vehicles and equipment must be
Marking warns friendly troops of contamination. marked or identified. Otherwise, maintenance personnel
Therefore, the signs are placed where they most likely could be injured by hidden contamination. One way of
will be encountered by friendly units. In rear areas the doing this is to attach a marker to the outside of the
entire circumference of the hazard area may need to be vehicle.
marked. Individuals who find the contamination place
the signs. They are placed where the contamination is
detected. Adjacent signs should be within sight of each Biological Sampling
other (25 to 100 meters apart depending on terrain). Since the type and amount of a Biological Warfare
This prevents units from missing the signs and entering a (BW) agent cannot be determined in the field, properly
contaminated area. Recon elements mark the area at the collected samples, along with accurate background
point of entry. Unit survey teams are then responsible information, is critical for the evaluation of a suspected
for determining and marking the extent of the use of BW agents. A properly collected sample can aid
contamination. in:
Some areas may contain more than one type of identifying the agent/confirming that an attack has
contamination or hazard. Mark these areas with the occurred
appropriate signs placed near each other. For example, if determining the proper therapy for exposed personnel
an area is both chemically and biologically contaminated, estimating the possible number and type of casualties
both signs are used and placed near each other. determining the time-to-casualties if time of the
For rear areas, in, around, and behind the Division attack is known
Support Area (DSA), and while in open terrain (i.e., evaluating an enemy’s BW capability
desert, plains, rolling hills . . . etc) it is possible to raise The reliability of evidence that BW agent(s) have been

5-7
FM 3-3

5-8
FM 3-3

5-9
FM 3-3

used is extremely important. Therefore, the collection of

samples and background information must be as detailed
and comprehensive as possible. Information presented by
witnesses must be screened to ensure that hearsay is not
substituted for accurate reporting.
Sampling is done by trained personnel. These are
usually chemical and/or NBC recon personnel. They
may be assisted/advised by intelligence or medical
personnel; such assistance should be incorporated into
SOPs and OPLANs. Trained personnel ensure uniform-
ity, viability, safety, and accountability in sampling
procedures. Sampling is not done indiscriminately, but
only when an attack has occured. Sampling operations
will be initiated only upon the knowledge and consent of
the NBCC. Sample priorities are bulk agent and delivery
systems, first; environmental (contaminated vegetation,
soil, water, and clothing), second; and biomedical
(patient or autopsy tissue, urine, and sputum) samples,
third. Biomedical samples should be taken only by
trained medical personnel. If trained medical personnel
are not available it may be necessary to retrieve the
entire remains for evaluation.
The standard sampling kit is the M34 CBR Agent
Sampling Kit or the Chemical-Biological Agent Sam-
pling Kit (CBASK). These kits contain material neces-
sary to obtain small liquid and solid samples. Directions
for use are contained in TM 3-6665-268-10.
Additional sampling operation guidance is as follows:
If the M34 kit is not available, a field expedient kit
can be assembled from like materials with the help of
supporting medical units. A list of suggested materials is
presented in Table 5-1 (page 5-12).
Hand-off points (most appropriately the decon point
for the recon mission team), sample couriers, special
packaging and handling procedures, chain of custody,
and diagnostic laboratory delivery points should be
coordinated and specified in SOPs/OPLANs. Otherwise,
the NBCC will have to coordinate and specify
requirements between medical, intelligence, recon, and
decon units not previously coordinated (along with any
special requirements dictated by the situation).
Commanders will ensure priority sample transport to
diagnostic laboratories.
Trained medics, intelligence, or chemical personnel
should be utilized as sample couriers.
A strict chain of custody must be maintained. This
allows samples to be traced to their origin.
Sample data must accompany the sample.
All samples will be in double containers to prevent
leakage during transport.
Detailed sampling techniques are further described in

5-10
 FM 3-3, C1

FM 3-19 NBC Reconnaissance. Small animals either dead or dying, especially where a
The following provides general guidance for BW toxic event is indicated, should be collected as a possible
sampling. source of sample.
Permanent structures such as buildings, walls, paved
surfaces or field vehicles are sources of impacted
Types of Samples adsorbed/absorbed sample. These can be sampled by
Liquids. scraping, swabbing or even washing (with collection of
Droplets on vegetation. the wash) and transported in bottles or tubes.
Dark stained spots on ground. Precautions should be taken to avoid unnecessary debris
Preferred sample - e.g., container of liquid (from in the extraction fluid.
storage). Priorities
stagnant pools - oily globules/suspended solids.
Streams where dead animals/fish are seen. Sampling Priorities.
Pools of water, ponds, streams, or reservoirs, can be Samples should be collected that provide objective
an important source of samples. These samples should indications of a biological attack. Sample collection
be kept in a cold state to enhance preservation of the should be planned and executed in accordance with the
suspect agent contamination. following general scale of relevance:
- First priority. Biological agents or munitions
Vegetation (including residues or fragments, NBC protective
Discolored equipment, in particular used respirator canisters and
Withered clothing.
Oily droplets - Second priority. Typical samples from the
Other unnatural particulates environmental (vegetation, earth, stones, water, etc.) in
Vegetation, whether grass, bushes, grain or other the vicinity of the alleged attack or incident.
growth is a definite medium for sample - Third priority. (Collected by medical personnel
absorption/adsorption. Quantities of the order of a only) . Biomedical samples, either from presumed
kilogram or more should be collected in bags made of casualties (samples of blood, urine, etc.) or from human
polyethylene or other relatively impermeable material. and/or animal corpses.
Soil General Precautions.
Discolored Many samples as well as the sampling site may be
Oily looking spots inherently dangerous. Appropriate individual protection
Soil, sand or rock in the direct vicinity of measures must be taken and specific precautions
dissemination or at least downwind or the event is an observed in collecting, handling, storing and transporting
important source of agent sample. The sand or soil samples. This is not only to safeguard those individuals
sample need not be taken beyond 4 cm in depth but handling the samples, but also to preserve the sample
preferably more than 100 cm in an area. Include plants, itself.
seeds, and debris when present. Even larger samples Technical advice and assistance. If munitions are to
should be taken if logistically feasible. Glass bottles or be handled or are in the area of the sampling site,
jars where feasible, should be used to hold the sample specific assistance and technical and ordnance advice
rather than plastic bags, to preclude the possible should be obtained. On-site medical assistance should
contamination of the soil sample by the plasticizers from also be obtained.
the bag. Samples should then be marked for
identification and returned to the laboratory.
Quantities
Ordnance Liquids - 1 teflon bottle 180 ML or 6 oz desired.
Munitions or fragments, whether originally from Vegetation - up to a kilogram or more of vegetation
shell, bomb, rocket, grenade, spent aircraft spray tanks should be collected when possible.
or other field dispersal system can be highly definitive Soil. 10 cm x 10 cm and a depth not to exceed 4 cm
sources of samples. Whole munitions or “duds” are a include plant, seeds and debris when present.
highly desirable source of sample, but should be handled Ordnance: Whole munition intact, no leaks if
(disarmed) only by explosive ordenance specialist. Small possible, commonly referred to as duds. Call ordnance
contaminated objects should be placed in kettles, sealed disposal units before moving.
and forwarded to the laboratory for analysis. Used personal protective and CB warfare equipment.

5-11
FM 3-3

Package each item separately.

Biomedical - Samples from dead animals. If the
organism is small, collect and ship the entire carcass.
Efforts should be made to collect the most common
species in the area for example, rats from local
dwellings, fish or common small birds.
Non-Transportable Items: Samples should then be
taken by scraping or rubbing the contaminated surface
with dry cotton wool or cotton wool soaked in distilled
water. The scrapings and the cotton wool pads shall be
carefully preserved in airtight Teflon containers.
Sampling Equipment
Various methods may be used to collect suspected
biological samples. For air samples, the XM2 Biological
Sampler provides an effective means of identifying
biological agents. Commercial air samplers can also be
used concentrate air samples for later identification.
However, the most common sampling tool is the
modular Chemical and Biological Agent Sampling Kit
(CBASK). If this kit is not available, a number of items
available through supply charnels or commercial sources
can be used. A listing of common materials available is
presented in Table 5-1.
The XM2 Biological Agent Sampler is a manually
operated device that is capable of providing identification
of specific biological agents after an attack, when used m
conjunction with an enzyme-linked immunosorbent assay
(ELISA) test kit. The ELISA tests are agent specific and
consist of a cotton swab and a test ticket. Once the air
sample is obtained, the cotton swab is placed in the
collection vial to absorb a small amount of substance.
The swab is then placed in a test ticket for a reading (see
Figure 5-13). Depending upon the urgency and the
degree of validity required for the identification, the
operator will draw one or two samples. Each sample
will take approximately 45 minutes for testing with the
ELISA test. The sampler, itself is powered by a 120V
AC ± 10 percent 60 Hz, 300 watt power source (see
Figure 5-14).
The sampler draws 1000 liters of air per minute and
separates the particles from the air, 2 to 10 microns in reconnaissance purposed). Although, with some
diameter. It then condenses these particulants into a 15 difficulty, a vehicle could move the XM2 from one
liter per minute stream of air directed into the wet pre-planned sampling point to another.
collector, where the particles become suspended in
liquid. Commercial Air Samplers
The remaining 985 liters is transferred to the cooling Many different styles and types of commercial
drawer and control module. Due to the large volume of samplers exist. These samplers are used by industry to
air drawn in, additional filters may be necessary to filter monitor for air pollution and airborne hazards
out dust, sand and dirt particles (NOTE: silt sand compounds. Each sampler has its own unique
average particle size is approximately 62 microns in characteristics and should be employed in the same
diameter). This sampler, when in the transit case weighs manner as the XM2.
240 pounds. (Therefore, because of it's size and power When handling the sample respiratory protection
requirements, the XM2 cannot be used for desired. DO NOT handle the sample. If the sample has

5-12
 FM 3-3

Employment
Employment considerations are more dependent on the
cloud parameters, climate and method of dissemination
than anything else, until agent specific cloud parameters
are made available. The XM2 will be employed at
preplanned point sampling sites within theater or area of
operations. These sites will be designated by the theater
or operational commander and are to be associated with
high probability targets. These targets may be large
urban areas, politically sensitive areas, logistical centers,
port facilities, airfields, large command and control
centers . . . etc. Due to the characteristics of BW agents,
until a sample is obtained, the collector operators do not
know if the agent is chemical or biological in origin.
The correct placement of an air sampler is depicted in
Figure 5-15a.

Modular Chemical and

Biological Agent Sampling
Kit (CBASK).
The equipment in this kit can be used to bring back
samples of solids, liquids, and gases. Three colors are
used to tell you which piece of equipment can best be
used for sampling solids, liquids, or gases. These are:
GASES. Use equipment such as the air pump and
adsorption tubes. (YELLOW)
LIQUIDS. Water cartridges, pipettes, and syringes
will be used to take samples from water or directly from
chemical liquids. (RED)
SOLIDS. Scoops, spatulas, knives, and bags will be
used to take solid samples such as dirt or chemical
powders. (BLUE)
The kit contains four packs, three of which are in
nylon bags. Use these packs for solid and liquid
sampling. The other pack cannot be removed from the
kit. This pack contains equipment for taking gas
samples. It also contains a small cooling box to hold
things which might rot or disintegrate. Colored circles
on certain equipment will help you identify its use. For
instance, yellow is for gas sampling.
Safety
Each kit comes with two pairs of butyl rubber gloves.
These gloves should be used at all times when you are
to be handled neoprene gloves should be used. sampling for possible agents. Further, wear the
Have the individual who has control of the sample, protective mask when safety conditions are unknown
place the sample in mylar bag or substitute (i.e., tin foil, (which is most of the time).
saran wrap.)
* NOTE: If sample is in a glass container with a lid Where to Take Samples
seal lid with pressure sensitive tape and triple wrap the The officer or NCO in charge will tell you where to
container first with tinfoil then saran wrap. take samples and the types needed. Generally, you will

5-13
 take solid samples in an area where agent drops are
suspected. You also need to take solid samples a short
distance away from the actual suspected area. These are
for comparison. LABEL everything with a number and
write down the coordinates of the area from which you
took the sample. Otherwise, write down a description of
the area so it can be located on a map. You have labels
and marking pens for this very important part of
sampling.

How to Sample
GASES - Unbagged Pack
Remove the equipment marked with YELLOW circles
for gas sampling. The battery powered air pump is
connected to the clear tubing. This, in turn, is connected
to one of the adsorption tubes (either end), which is
stored in the glass tube. The pump is turned on (small
switch on front). If you have trouble turning on the
switch with gloves on, use the small screwdriver to push
the switch on and off. It is already set for large volume
flow. Place the pump and tube in the area to be
sampled. About 20 minutes is enough. After this time,
disconnect the tube and place it in the steel tube holder.
A small piece of Teflon tape can be placed over the end
of the tube before you screw the cap on. Tighten the
fitting (nut) with the pliers. Place a label with an ID
number on the tube. The sample is now ready to bring
back.
This kit also contains the cooling box. If you collect
leaves or samples which might rot (or obvious agent
powders), place them in the box. You are given two
cold bags to cool the samples down. Squeeze them and
place them in the box with the samples. Put the box lid
securely on. Connect the batteries to the cooling unit.
Place labels on the box lid with ID numbers on the
samples, or on containers, if you used them to contain
the samples. The samples are ready to bring back.
LIQUIDS - Unmarked Packs
All equipment to be used for liquid sampling is
marked with small red labels. To sample water which
may contain agent, you need three items: The plastic 60
mL syringe, a three-way valve, and a Sep-Pak cartridge.
Remove the tip protector from the syringe. Also remove
the three protectors from the three-way valve. Connect
the three-way valve and the syringe so that the green cap
of the valve is pointing away from the syringe. The
small handle on the valve lets you pull water up into the
syringe and send it off in a second direction. Now,
connect the Sep-Pak (short end) to the green tip end of
the three-way valve. You need to prewash the Sep-Pak
before sampling. Do this by setting the valve handle 90
degrees to the aligned syringe, valve, Sep-Pak system.

5-14
 FM 3-3

Place the tip of the open end of the Sep-Pak into the Collectors should be encouraged to collect the samples
bottle containing methanol. Draw the contents of the in quantities that do not exceed 10 cm in diameter and 14
bottle into the syringe. Now, place the valve handle in cm in length to facilitate subsequent handling and storage
line with syringe, valve, Sep-Pak system, and eject the in the laboratory. In addition, excess bagging by
methanol out the side opening of the valve. Do the same collectors should also be discouraged. However, DO
thing with the bottle containing water. You are ready to NOT break down and repackage samples to meet the
sample. Do this by pulling the sample up through the above requirements.
Sep-Pak (valve 90 degrees to system). Eject the used Place any breakable containers in more rigid
sample by changing the valve setting (valve in line with containers, with protective absorbent material (vermicu-
the system). Label the Sep-Pak with ID number on lite, styrofoam, excelsior or charcoal-impregnated wad-
either white tape or label, along with the pH number (see ding) to protect them from puncture or breakage.
below). Place the Sep-Pak in one of the small plastic Preservations and packing for transport.
bags.
Check the pH of the water from which you took In general terms, the lower the temperature, the
samples before you leave the sampling area. Do this by longer the life of chemical or biological warfare agent
placing the tip of one of the pH indicator strips into the samples. Samples must therefore be at least
water. Compare the color of the strip with that on the refrigerated, whatever their nature.
box. Write the pH number on the label of the Sep-Pak If all the samples cannot be chilled, priority should be
sample. given to cooling samples of vegetable and biological
To sample possible liquid agents or other liquids, materials.
you are supplied with small plastic pipettes. Draw the In the field, insulated boxes having a polystyrene
liquid into the pipette then expel (squeeze the bulb) the interior with compartments to hold flasks may be used,
liquid into one of the small plastic, white bottles. Screw with bags being loosely laid in them.
the cap shut and place this bottle into the next largest A sufficient quantity of pre-chilled refrigerating packs
sized plastic bottle. A piece of Teflon tape can be placed (camping-type bags containing polyethylene glycol) can
over the grooves of the bottle before you screw the cap also be placed in the box. Empty spaces should be filled
shut. This gives a better seal to the cap. If there are any with vermiculite, styrofoam, excelsior or charcoal
spills on the outside of the bottle, wipe them with the impregnated wadding.
gauze pads and discard the gauze. Label this bottle with Labeling.
an ID number. This bottle and others can now be placed Tags or adhesive labels should be affixed to each
in the large plastic bottle for safe transport. If you don’t sample container. On each should appear a code number
find any liquid agents, these plastic bottles can be used which clearly refers to the accompanying sample data
for solid samples. sheet that documents the nature and circumstances of
Solid - Unmarked Packs collection.
To sample solids, including contaminated dirt, you Sampling
can use the plastic scoop, tongs, or the plastic spatula. LA* = 850115-002-JD
A pair of scissors and a knife are also available for LA = Sample was acquired by collector in Laos
cutting samples. Place the solid samples in plastic bags 850115 = Sample obtained on 15 January 1985
and label each of the bags with an ID number or other 002 = This is the second sample obtained on 15
information. If you have empty plastic bottles, these can January 1985 by the collector
be used for solid samples. JD = The sample was collected by John Doe
General Packaging Procedures * See Annex B for country codes
Packing of environmental samples. Samples should be Place the sample in a zip-lock bag if available.
double wrapped or bagged. Place sample in a metal can. Line inside with
Place the Mylar bag or glass container containing the absorbent packing material. The can helps absorb shock
sample into a corner of a second mylar bag. Remove from rough handling during shipment.
excess air and twist the neck of the bag until it forms a Ice Chest.
tight coil with the bag snug around the sample bag or Standard polyethylene or metal ice chests are the most
container. There should be no air pockets. Make a easily procured items which can be used for tram-world
gooseneck in the bag by folding the coiled neck in half shipment of BW samples. The most easily used size is
and wrapping it tightly with tape. Mark bag with about 24 inches long by 18 inches high by 15 inches
identification numbers of samples within. deep. This size permits the sender to ship two or three

5-15
FM 3-3

sizes of pound metal cans in each chest with sufficient Explain what happened if yes.
coolant to maintain freezing temperatures for about four Describe your symptoms during the attack (durations,
days. Additionally, each chest remains at a weight how severe, other people affected?)
which can be handled by a single individual. Any problems with your - head?, eyes?, breathing?,
skin?
Coolants. These questions are designed to allow an interviewer
The best coolant available in most areas is dry ice. It to note MOST relevant details of testimony given by
maintains low temperatures for several days and can be personnel associated with alleged use of chemical or
handled easily. Blue ice, a plastic-containerized biological warfare agents. Do Not consider the
refrigerant, can be used if available but will not maintain questions to be all inclusive.
freezing temperatures for as long as dry ice. Standard
ice should only be used as a last resort because of its Acquisition Reporting
rapid melting rate and the possibility that melted ice may An electronic report should be forwarded by the
contaminate samples. collection team upon acquisition and shipment of
samples to report information that has been obtained.
Internal Insulation. Information should be forwarded through the nearest
Even though a commercial ice chest provides good diplomatic or consular post, intelligence agency, or if
insulation of both the samples and the coolant, extra neither are available, through the nearest U.S. military
insulation and cushioning should be placed around the unit having secure radioteletype communications.
metal cans inside the chest. Newspapers, plastic bubble The team should insure that the acquisition message
wrap and foam rubber may all be used with almost has been properly classified.
equally good results. The acquisition report should include the following
Label Ice Chest: addressees at the minimum:
Commander Chemical Research Development and
Engineering Center ATTN: SMCCR-OPF Aberdeen SECSTATE WASHDC
Proving Ground, Maryland 21010 SECDEF WASHDC//OSD-ISA//
The Commander, CRDEC will notify the Commander JCS WASHDC//J-3/J-S
of the Technical Escort Unit. This unit controls CIA WASHDC//OSWR-STD-LSB//
transportation of the samples to their final destination. DA WASHDC//DASG-PSP, CDR, USAMRDC FT
They will intercept the samples upon arrival at a DETRICK MMD//
CONUS Airport. DIA WASHDC//DT-3B/DT-5A//
DIR AFMIC FT DETRICK
WARNING MD//AFMIC-CR/AFMIC-SA//
Under no circumstances should suspected toxic DA WASHDC//DAMI-FIT/DAMO-NCC/SAUS-C//
samples or munition systems be shipped to CMDT USACMLS FTMCCLELLAN
CONUS technical centers or intelligence agencies AL//ATZN-CM-CC//
without prior approval by the recipient. * NOTE: CDR CRDECAPG MD//SMCCR-OPF//
OCONUS pick-up by technical escort personnel CDR FSTC CHARLOTTESVILLE
may be possible. VA//AIAST-FM/AIAST-CW//
The action addressee is:
Cdr, CRDEC, APG MD//CBATEB//
An acquisition message will contain the following
Witness Interview information:
The witness interview may play the most important The sample identification number will be a part of the
role in sample acquisition. Information received can aid subject line if only a single sample is referred to in the
in the identification of the sample. Interviewers should text. Otherwise, the sample number will be referred to
insure that testimony accurately describes scientific within the message body with its background
reality and not a social or political “truth”. Interviewers information.
should also avoid yes or no questions. Below is a list of The date the sample is to be shipped, the mode of
questions that could be asked during an interview: transportation, courier identification, air bill of lading
Name: number, flight number, destination and estimated time of
Where can you be located in the future? arrival will be included if the sample is to be shipped
How was the sample obtained? immediately.
Where was the sample obtained? Background information surrounding the sample.
Were you present during the attack?

5-16
 FM 3-3

If the circumstances surrounding acquisition of a be established in the theater of operations to minimize

sample were questionable, appropriate information must confirmationtime. CONUS labs will also be utilized to
be included. verify the results of the theater labs. This information
If a portion of the sample or information concerning will then be disseminated to subordinate units to insure
the sample has been shared with a nation or an agency that adequate protective measures are implemented for
not shown on the message address, or if another country protection of both civilian and military personnel.
or agency has acquired a sample from the same event or Confirmation of an enemy biological attack will also be
area, this should be indicated in the acquisition report. reported to the National Command Authority (NCA) for
A recommended priority and rationale for analysis a decision concerning the appropriate military and
should be included in order to guide the analysis center diplomatic response. Figure 5-16 shows the standard
as to the team’s assessment of the potential value of the chain of custody for the evacuation of biological
sample. samples.
All details which relate to the acquisition of the Suspected
sample should be included regardless of how Biological
insignificant they may seem to the collector. Attack
Disposition of samples should be made according to Bio-Medical
their physical category. Environmental Sample
Unit S-2
Evacuation of Samples Technical Intelligence Foreign Materiel Intelligence
Biological samples must be evacuated to the Unit
appropriate laboratory facilities for confirmation of a Tech Escort
biological attack. Under normal circumstances labs will In-Theater Labs
CONUS Labs

5-17
FM 3-3, C1

Chapter 6
Civilian Chemical Hazards
Every nation in the world has some form of hazardous Esablish evacuation procedures for noncombatants.
chemical production or storage facility. Most of these Identify a chain-of-command for supervision and
chemicals are used for peaceful purposes and are coordination of the clean-up effort.
considered to be in one of the following categories: In the event civilian chemical compounds are released
Agricultural - includes insecticides, herbicides, the fallowing steps should be taken immediately by the
fertilizers . . . etc. tactical units within the area:
Industrial - chemicals used in manufacturing Notify higher, lower, and adjacent units.
processes or for cleaning. Start continous monitoring with available detection
Production and Research - chemicals (as well as equipment. Assume MOPP4.
biological agents) used in research or are produced in a Secure the area around the facility. Establish a
facility. security perimeter of 620 meter radius around the sight.
Damage or destruction of a facility or storage site; or From this perimeter, draw a 10 km radius to indicate the
any act that creates the unexpected release of civilian potential downwind hazard zone (refer to Figure 6-l).
chemical products into the environment will present Evaculate all personnel from within the 620 meter
unique challenges to U.S. and allied Armed Forces, as security zone. All personnel within the 10 km hazard
well as the citizens of the Host Nation (HN). Once zone should assure full chemical protection (MOPP4) or
released, these hazards may cause immediate or delayed be evacuated from the area. Maintain this posture until
incapacitation or death. To safeguard friendly forces relieved by appropriate response team or Military Police.
and civilians from the potential hazards, peacetime and The perimeters of the security or hazard zone may
tactical chemical contamination avoidance principles increase or decrease after the response team(s) arrive on
must be carefully blended. scene depending upon agent involved, extent of damage
Civilian chemical compounds may not be detectable and weather conditions.
by the standard chemical detection devises of tactical
units (see Chapter 3 description of these devises).
Civilian compounds may not be detectable with the
human senses and may cause symptoms that are different
than those symptoms from war chemicals.
To minimize the effects or hazards resulting from the
damage or destruction of a chemical or biological
facility, prior planning must occur. When friendly units
are required to operate in an area where such a facility
exists, the chemical staff must:
Coordinate, through G5/S5, with the HN emergency
response teams. These teams may be from the HN
government, armed forces or from the facility itself.
Identify what chemical or biological material is
present, what type of contamination hazard is present,
and how far will the contamination hazard extend.
Determine whether standard Chemical Defense
Equipment (e.g., protective mask, boots, suit, gloves)
will protect against the potential harmful effects of
released compounds.
Coordinate with Divisional Chemical for technical
assistance
Coordinate with higher headquarters and HN to
identify the availability of CAIRA (Chemical
Accident/Incident Response and Assistance) teams
Technical Escort units or similar civilian agencies
available to assist if required.

6-0
 FM 3-3

Appendix A
CB Operational Situation
Contamination Avoidance
This appendix provides a series of operational situations that outline how contamination avoidance tactics,
techniques, and procedures (TTP) can be applied. The various situations are designed to assist commanders and
chemical staff personnel in tactical operations. The TTP included are not designed to replace Army Training and
Evaluation Plan (ARTEP) standards, nor any other listing of collective tasks, but is intended to be an operational
contamination avoidance checklist. These checklists are not all inclusive and may be adapted or modified for local use.

Platoon Through Brigade Task Force

Chemical and Biological Operations Checklist
Situation: Commander directs units to prepare for operations in a chemical or biological environment. The following
specifics apply-
a. Enemy is capable of offensive chemical or biological weapons employment.
b. Unit is provided intelligence on enemy NBC capabilities and likely courses of action.
c. NBC threat status (chemical or biological) is Serial 2 or higher.

Platoon/Company Actions Battalion/Task Force Actions

1. Authorized unit detection and individual protective 1. Oversee subordinate unit actions.
equipment is on hand, operational and issued per unit 2. Prepare CDM report and send to subordinate units.
SOP. 3. Ensure contamination avoidance measures are
2. Commanders perform MOPP analysis based on initiated around the headquarters complex IAW SOP.
METT-T and higher headquarter’s guidance. 4. Ensure chemical defense equipment (CDE) shortages
3. Immunizations are updated and field sanitation are placed on order and contingency stocks are
measures are enforced. serviceable and deployed IAW SOP.
4. Nerve Agent Pretreatment (NAP) and ciprofloxin
tablets are provided to soldiers.
5. OPSEC, dispersion, cover and concealment are
practiced.
6. Unit receives and correctly interprets periodic
Chemical Downwind Message (CDM).
7. Unit adopts NBC contamination avoidance measures
such as covering supplies and equipment with NBC
Protective Covers (PC).

A-1
FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological Checklist
Situation: Commander directs unit to prepare for a chemical or biological (toxin) attack. The following specifics
apply:
a. The enemy has or is likely to employ chemical or biological (toxin) weapons.
b. Chemical/biological weapons employment is considered to be a likely course of enemy action.

Platoon/Company Actions Battalion/Task Force Actions

1. Subordinate units are alerted. 1. Alert subordinate units and elements of the Task Force.
2. Commander(s) specify appropriate MOPP levels; 2. Monitor the unit’s MOPP status.
establish automatic masking criteria; and, if MOPP 0 3. Ensure subordinate units have taken measures out lined
is assumed, determines the location for chemical by unit SOP.
protective clothing based on METT-T. 4. Ensure subordinate units have received the most
3. Unit continues the mission while implementing current CDM.
actions to minimize casualties and damage. 5. Plan for possible decon support, establish decon
a. Personnel, equipment, munitions POL, food, and priorities, locate hasty and possible detailed decon
water are protected from contamination. sites, and coordinate with the BDE HQ.
b. Detection paper is placed to provide visibility and 6. Ensure biological agent samplers are prepared for
maximum exposure to liquid agents. operation.
*c. OPSEC, dispersion, cover and concealment are
practiced so the unit may avoid being targeted.
d. Chemical/biological detectors, samplers, and
alarms are checked and prepared for use.
*e. Ensure unit has update CDM on hand.
f. Chemical Agent Alarms, biological samplers,
LP/OP, and air guards are employed as required
and/or the tactical situation permits.
* Company Only

A-2
 FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological Checklist
Situation: The commander directs the unit to respond to a chemical/biological agent (toxin) attack. The following
specifics apply:
Subordinate unit or units or the battalion/task force is (are) subjected to a chemical or biological agent (or toxin)
attack.

Platoon/Company Actions Battalion/Task Force Actions

1. All personnel automatically mask, sound alarm, 1. NBC 1 Reports are received and passed to
decontaminate themselves as required, assume MOPP subordinate, adjacent, and higher units.
4, and administer self-aid and buddy-aid. 2. NBC 1 Reports are consolidated to form an NBC 2
2. If the unit has access to a Biological Agent Sampler, Report. The NBC 2 Report is posted to the situation
(an XM2 or Commercial Sampler) activate sampler. map as an overlay. The report is passed to
3. The Chain of Command and communications are subordinate, adjacent, and higher-units.
restored, and the unit continues with the mission. 3. NBC 1 (Follow-up) Report is requested to identify the
4. In the event of a biological attack and the unit does toxic agent. The hazard area is predicted and
not possess a sampler, unit should collect samples disseminated to subordinate/ slice units via NBC 3
with either the M34 Biological Agent Sampling Kit Report.
or CBASK. 4. XM2 or commercial biological samples obtain sample
5 Adjacent units are warned immediately of the and forward to area lab for analysis.
potential downwind vapor hazards. 5. Subordinate unit damage assessment is evaluated. If
6. Unit identifies type of agent and submits an NBC 1 required, assistance is provided to the unit for
Chemical or Suspected Biological Report as the reestablishing command and control. This report is
mission permits. passed to the battalion S1 and S4 for action and/or
7. For attacks that leave liquid or solid contamination on information.
equipment, personal, or terrain, perform the 6. If attack is determined to be a biological attack:
following: a. If agent is determined to be anthrax, soldiers must
a. Conduct personal wipedown and operators complete immunization program and start taking
spraydown. ciprofloxin antibiotic tablets.
b. Warn MEDEVAC of contamination casualties. b. If agent is unknown, all attempts must be made to
KIAs are wrapped and marked. assist in the identification of the agent.
c. Mark contaminated area and relocate to a clean 7. Decontamination requirements are determined based
area if the mission allows. on METT-T, extent of contamination and the
d. Determine where and when further decon can be availability of assets.
accomplished if necessary. 8. If decontamination is required and METT-T
e. Coordinate for decon and resupply of protective conditions permit, a decontamination request is
clothing and decontaminates. prepared IAW SOP and sent to the supporting
f. Ensures contaminated BDOs are exchanged within chemical unit provided it is part of the Battalion’s
24 hours after being contaminated. Task Force. If the chemical unit is not available, the
g. Replace contaminated NBC-PCs within 24 hours. request is forwarded to higher headquarters.
8. For nonpersistent agents, the unit: Decontamination priorities are determined and
a. Conducts unmasking procedures. followed in either case.
b. Treats casualties and prepare for evacuation as the 9. Contingency stocks are reordered to replace used
mission permits. items.
c. Service detection systems to ensure operational
status.
d. Service XM2 or commercial samplers to ensure
operational readiness.
*9. Receive NBC 2 Report, plot potential hazard area
and inform the commander.
* Company Only

A-3
FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological Checklist
Situation: The commander directs the unit to conduct post attack operations. The following specifics apply:
Unit or elements of the task force have been subjected to a chemical or biological attack.

Platoon/Company Actions Battalion/Task Force Actions

1. Unit has undergone decontamination operations and 1. Ensure attacked unit has completed necessary decon
casualties have been evacuated. measures and evacuates casualties.
2. Unit reorders CDE equipment (i.e., MOPP suits, 2. Receives report from area lab on agent analysis.
filters, NBC PCs, M258A1 refill kits . . . etc). Inform higher headquarters of results.
3 If unit has not yet determined whether or not the 3. Ensure attacked unit and medical unit in support
attack was biological/chemical, efforts continue to re-orders CDE used.
make this analysis. Efforts continue to identify what 4. If attack was of biological origin:
agent was used. This will be done by: a. Inform supporting chemical unit for decon
a. M256A2 kit. operations.
b. Chemical Agent Monitor (CAM). b. Ensure that the personnel attacked take appropriate
c. Sampling with XM2 biological agent sampler or antibiotic or antitoxin, if available.
commercial samplers. c. Inform medical personnel to be alert to potential
d. Obtain samples with either M34 kit or CBASK. infected casualties.
Samples forwarded to area lab for analysis. 5. Continue to refine the limits and extent of the
4. If the units must continue to operate in or occupy the contaminated area and inform the commander on the
contaminated area, the unit should: effects of contamination on future operations.
a. Continue efforts to refine the contamination hazard 6. Monitor natural decay of agent. Be alert to conditions
area and extent by continued sampling/detection. which may cover or move contamination to
b. Adjust or improve MOPP as required. previously clean areas. This may occur through
c. Mark contaminated areas and identify “hot spots”. natural sources (i. e., wind, water . . . etc) or
d. Monitor contamination decay or covering to man-made sources (rotorwash, vehicle traffic . . . etc).
determine when natural decay may render the area a. Take periodic soil samples and air samples with
safe. XM2 or commercial samplers and forward to the
e. Be alert for “transient contamination”, the area lab for analysis.
spreading or movement of contamination by b. Monitor terrain with M8/M9 paper, CAM or
natural sources (i. e., wind, rain, runoff, rivers . . . M256A2 kit for chemical contamination.
etc) or by human sources, (i. e., vehicle traffic, c. Be prepared to advise commander on when the
rotorwash . . . etc). agent is expected to decay to a safe level.
5. In the event of biological contamination:
a. If the biological agent is reported to be Botulinum
toxin, affected personnel must begin antibody
treatment.
b. If the biological agent is reported to be Anthrax,
soldiers must complete immunization program and
begin taking the ciprofloxacin antibiotic tablets.
c. If the biological agent is unknown, all efforts must
be made to assist medical personnel in the
identification process.

A-4
 FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological Checklist
Situation: The commander directs the unit to operate in a chemical/biological agent (toxin) contaminated area. The
following specifics apply:
Unit must remain in a contaminated area.
Platoon/Company Actions Battalion/Task Force Actions
1. Unit continues the mission. 1. Units receive warning from higher or adjacent units in
*2. Using an NBC 1 or 2 Report from higher HQ or an the form of an NBC 2 or NBC 3 Report or an NBC 1
adjacent HQ, the unit prepares a downwind vapor Report from subordinate or adjacent units.
hazard prediction. The commander is advised of 2. Prepare a downwind vapor hazard prediction and
estimated cloud arrival time, and subordinate units are determine the effects. The units within or close to the
notified. predicted area are alerted to the possible downwind
3. Chemical agent alarms are employed per unit SOP if hazard.
the situation permits, it or an LP/OP is used. In the 3. Units continue the mission. If and when the unit is
event of a biological attack, and an XM2 or within the downwind hazard, follow steps for
commercial sampler is available; activate sampler. responding to a chemical/biological attack (page A-3).
4. When an NBC Report is received, plot it to update 4. Battalion/Task Force Commander is advised of the
previous estimates. estimated cloud arrival time, chemical agent, extent
5. Commanders perform a MOPP analysis to determine of downwind vapor hazard, and an estimation of the
level of protection. duration of the contamination.
6. Unit reacts to the arrival of the downwind vapor 5. The commander determines the course of action and
hazard and at a minimum assumes a “Mask Only” MOPP level based on METT-T, guidance from
posture. higher HQ, and the advise from the battalion/Task
7. Commander conducts unmasking procedures if Force Chemical Staff.
appropriate, and adjusts protection as appropriate by 6. The commander’s guidance is sent to the subordinate
using MOPP analysis. units.
*Company Only 7. The subordinate units emplace alarms, biological
samplers and other detection IAW SOP.
8. Ensure subordinate units are complying with the
commander’s guidance and report the arrival of the
agent cloud.

A-5
FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological
— Checklist
Situation: The commander directs the unit to respond to a chemical/biological agent (toxin) contaminated area. The
following specifics apply:
Unit must remain in a contaminated area.
Platoon/Company Actions Battalion/Task Force Actions
1. Unit continues the mission, 1. Unit continues the mission.
*2. Commander specifies MOPP level needed to provide 2. Ensure subordinate units continue to monitor area for
required protection and adjusts work rates and activity hazard duration and/or clean areas.
to prevent MOPP heat stress. 3. Ensure subordinate units continue to practice
NOTE: Until positive identification is made to contamination avoidance procedures IAW SOP.
determine whether the snack war a chemical or 4. Ensure CDE is reordered when required.
biological agent; unit should remain in MOPP 4 for a 5. Coordinate with higher headquarters for
minimum of 4 hours. decontamination support.
3. Commander estimates the duration of contamination
and the time of stay within the contaminated area and,
as required, initiates actions to maintain unit
effectiveness.
a. Buddy system is employed to watch for symptoms
of chemical (toxin) agents, stress from heat and
encapsulation, and administer immediate first aid.
b. Water consumption is supervised to ensure every
soldier consumes 1 quart every 3 hours (every 2
hours if the temperature is above 80 degrees F).
c. Clean areas are located where soldiers can be
rotated to eat and rest.
*d. Arrangements are made for MOPP gear exchange
if contaminated soldiers must stay in MOPP for
over 24 hours.
4. Contamination avoidance and hasty decon techniques
are used to minimize the spread of contamination.
* Company Only

A-6
 FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological Checklist
Situation: The commander directs the unit to cross a chemically or biologically contaminated area. The following
specifics apply:
a. Subordinate units or the Battalion/Task Force must cross an area contaminated with persistent chemical or
biological agents.
b. The unit is moving and the reconnaissance teams discover that the area in which the unit must cross is
contaminated.

Platoon/Company Actions Battalion/Task Force Actions

1. NBC Report and/or contamination overlay is posted to 1. The unit has or obtains current SITREPS on the
the situation map. Unit conducts or requests surveys contaminated areas. Ensures this information is
of different routes if time permits. passed to all effected units.
2. Commander uses available information to determine 2. NBC 5 Report and/or overlay is posted to the situation
the best route based on contamination avoidance map to aid the commander in selecting the appropriate
principles and mission requirements. route.
*3. Advance party/advance guard/point has chemical 3. The crossing subordinate unit must receive the most
detection supplies and equipment to test for current NBC 5 Report to be used in determining an
contamination and downwind vapor hazards along the appropriate route.
route. They report contaminated areas unless 4. Route clearance is requested (if required).
otherwise directed by the commander. 5. Notify the crossing unit(s) of decontamination assets
NOTE: If the unit possessor has access to an NBC available and hasty or detailed decontamination site(s)
Recon System (NBCRS), this vehicle should be used with to be utilized after crossing.
the advance party. 6. If internal decontamination support is not available
4. Personnel and equipment are prepared for crossing additional decontamination support will be required,
by: notify the BDE/MUC.
a. Increasing MOPP as required. 7. Crossing unit receives contingency stocks of CDE,
b. Ensuring M8/M9 Paper is placed on clothing and and the unit is prepared to cross the area IAW SOP.
equipment. 8. Crossing unit executes contamination avoidance
c. Ensuring chemical alarms are serviced and techniques IAW SOP.
mounted on vehicles or carried by personnel IAW 9. After crossing the area, ensure crossing unit(s)
SOP. determines their decontamination requirements and
d. Ensuring Ml1 decon apparatus and/or M13 DAPs request decon support IAW SOP.
are serviced, filled and mounted on vehicles. 10. Notify higher HQs that the crossing is completed,
e. Ensuring M256A1 detector kits are issued to the number of casualties sustained (if any), and the
operators. decontamination support requirements and/or decon
f. XM2’s or commercial samplers cannot be operated operations scheduled.
on the move. Units, however, should obtain 11. Ensure that the subordinate unit reorders contingency
samples of suspected contamination with either the stocks of CDE as required.
M34 or CBASK if time and mission permit. 12. Ensure that the subordinate unit reports the
5. Unit crosses the contaminated area using completion of decontamination operations to higher
contamination avoidance techniques. HQs.
6. After exiting the area, hasty decon should be
performed provided the mission is not jeopardized
(commander’s decision).
* Company Only

A-7
FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological Checklist
Situation: The commander directs the unit to conduct a chemical or biological survey. The following specifics apply:
a. A downwind hazard prediction indicates chemical or biological agents may affect the units’ operational area.
b. Areas of interest within the units’ operational area may be contaminated with a chemical or biological agent.
c. Higher headquarters directs unit to conduct a chemical/biological survey in the unit’s area of operation.
d. The tactical situation requires the unit to conduct a chemical/biological survey.
Platoon/Company Actions Battalion/Task Force Actions
1. Unit initiates or is given an area to be surveyed, plans 1. Unit receives the mission request and/or determines
the survey, and organizes the party. The briefing the area to be surveyed. Request support from an
includes but is not limited to the following: NBC reconnaissance vehicle, if possible.
a. Type of recon and/or technique to be employed. 2. Ensure subordinate unit initiates, conducts, and
b. Reporting requirements. reports survey data IAW the guidance from the
c. Marking requirements. requesting headquarters SOP.
d. Special preparation of vehicle to enhance 3. Alert the supporting chemical unit to the potential
contamination avoidance. need for decontamination of survey party. If the
2. Survey team(s) execute(s) mission as directed. battalion does not have an organic supporting
*3. NBC Defense Team submits evaluated data to higher chemical unit, the battalion notifies the MUC.
headquarters. 4. Identify potential decon lamination sites (if required).
4. Unit decontaminates as required. 5. Ensure subordinate unit reports the start time of the
* Company Only survey, significant finds, and completion time of the
survey.
6. Ensure subordinate unit submits the NBC 4 Report as
required by the SOP. The report is received, logged
in, checked for accuracy, and forwarded to higher
headquarters. The battalion keeps a copy of this
report.
7. Survey findings are posted or annotated on the
situation overlay IAW SOP.

A-8
 FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological Checklist
Situation: The commander directs the unit to conduct decontamination operations (hasty or detailed). The following
specifics apply:
a. Subordinate unit(s) report contamination from a persistent chemical or biological agent.
b. Personal wipe down has been completed but personnel are still contaminated.
Platoon/Company Actions Battalion/Task Force Actions
1. Unit determines the extent and numbers of 1. Subordinate unit requests decontamination IAW SOP.
contaminated personnel and equipment. 2. The commander is briefed on the type and extent of
*2. Unit requests decon support and coordinates for contamination, how long the contaminated unit can
chemical protective clothing and decontaminates for stay in the current posture without further
detailed troop decon. decontamination, the availability of a chemical unit
3. Unit designates decon team, moves to the assembly support, and a recommendation on which decon
area which is downwind from the decon site, links up should be done.
with chemical company’s decon unit, and receives a 3. The commander decides if the unit will initiate
briefing on the decon site operation. decontamination operation, and if so, whether the
4. Unit conducts detailed troop decon and sends decontamination will be hasty or detailed. The
equipment to the detailed equipment decon site as decision is based on METT-T and the advice from the
instructed by the chemical company decon unit’s OIC Battalion/ Task Force Chemical Staff.
or NCOIC. 4. The commander’s decision is transmitted back to the
*5. Unit conducts detailed troop decon for the chemical requesting unit as follows:
unit after it completes its mission and it closes the a. If the decision is not to decontaminate, the
troop decon site. subordinate unit is provided guidance on protective
6. Unit completes reconstitution and resumes or awaits measures to take.
the next mission. b. If the decision is to decontaminate utilizing hasty
* Company Only decontamination procedures then:
(1) The battalion requests decontamination support
from the chemical unit if decon assets are not
organic to the battalion.
(2) The subordinate unit is (are) notified of the
decision and location of the linkup point of the
decontamination site.
(3) The battalion notifies the contaminated unit and
ensures that their unit deploys the decon team to
prepare the site. The unit decontamination team
will operate the decon site. The battalion decon
team or chemical platoon will do the vehicle
washdown for the decon team. If this support is
not available, the unit’s decon team will operate
the site utilizing organic decontamination assets,
e.g., M13 DAP and/or M11. The unit decon team
establishes entry and exit traffic control.
c, If the decision is to decontaminate utilizing detailed
decontamination procedures, then the following
occurs:
(1) The battalion requests detailed decon support from
the supporting chemical unit.
(2) Subordinate unit is notified about the decision,
location of the decontamination site, amount of
time the unit has to complete decontamination
operations and which unit if any will relieve the
contaminated unit in place or assume the

A-9
FM 3-3

Battalion/Task Force Actions (Continued)

contaminated unit’s mission during
decontamination.
5. Subordinate unit will be given the time for reporting
to the decon site, moving into the predecon staging
area, rendezvous, point of contact at the site, route
and type of march to and from the site, etc.
6. Battalion will ensure contaminated units decon team
operates the decon site IAW SOP. If more than two
(2) companies require decontamination, the battalion
will coordinate with the MUC for additional decon
assets.
7. The contaminated unit reports arrival at the decon
site, completion of 50% of the unit, and completion
of decon operations to the BN HQs.
8. Battalion reports completion of the decon operations
and site closure to the MUC.
9. Subordinate unit reorders contingency stocks of CDE
that were expended during decontamination.

A-10
 FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological Checklist
Situation: The commander directs the unit to evacuate chemically or biologically contaminated casualties. The
following specifics apply:
Unit has sustained casualties that are chemically or biologically contaminated.
Platoon/Company Actions Battalion/Task Force Actions
1. Unit requests medical evacuation based on normal 1. Subordinate unit informs HQ on the number of
considerations of medical care required, urgency, and casualties, type and time of contamination and method
the tactical situation. Evacuation requests will be of evacuation desired.
made IAW SOP. 2. Notify the subordinate unit that has been designated to
2. Unit informs higher HQs on how many casualties provide a ten (10) man detail for patient decon
were sustained, type of contamination and mode of support. Ensure subordinate unit is provided with the
evacuation. time for the detail to report, location of Battalion Aid
3. Casualties are brought to MEDEVAC aircraft or Station (BAS), and POC at the BAS.
vehicle. Unit will take measures to limit the spread of 3. Battalion Aid Station (BAS) is notified of incoming
contamination. casualties. BAS has a ten (10) man detail on hand to
4. Casualty is marked, identify type of contamination assist in decontamination.
and first aid received. 4. Notify higher HQs on the number of casualties, type
of contamination, and estimated time of arrival (ETA)
to the BAS.
5. Notify the supporting chemical unit or higher HQs
about the possibility for decontamination support
either for the MEDEVAC helicopter or ground
ambulance.
6. Ensure that a responsible individual who is
knowledgeable in NBC defense is at the BAS to assist
in casualty decontamination. This individual must
ensure that aircraft or ambulance personnel off load
casualty into a designated area which is downwind
from the BAS and will assist or ensure the crew of the
vehicle or aircraft monitors for contamination.
7. Ensure that the BAS coordinates with the battalion for
decontamination (if required).
8. Inform the BAS when to have the ambulance or
helicopter report to the decontamination site, from
what direction to approach the decon site, and point
of contact at the site.
9. Ensure that the ambulance or MEDEVAC helicopter
is decontaminated IAW SOP. Decon site will be
operated by the detail unit who provides a casualty
decon team to the BAS.

A-11
FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological Checklist
Situation: The commander directs the unit to prepare for a friendly chemical strike (CHEMWARN). The following
specifics apply:
a. The unit is notified by higher HQ that a friendly chemical strike will occur in the unit area of operations (AO).
b. The unit receives CHEMWARN message.
Platoon/Company Actions Battalion/Task Force Actions
1. Unit requires authentication if unsecure net is used. 1. The unit locates ground zero (GZ) or target area on
2. Unit acknowledges warning receipt. the map and plots the hazard area.
3. Unit relocates if required. 2. The unit determines which subordinate unit(s) must
4. Unit implements protective measures prior to strike iritiate protective measures or relocate.
IAW SOP and maintains protective measures until 3. The commander is briefed on the impending strike
strike is executed or cancelled. and post detonation effects.
4. The unit directs subordinate unit(s) which will be
affected to relocate or implement protection measures
IAW SOP.
5. The unit notifies MUC when all company and
separate platoon-size units in battalion area of
operations have been notified.
6. Ensure affected unit(s) take appropriate protection
IAW SOP.

A-12
 FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological Checklist
Situation: The commander directs the unit to respond to an unexpected contaminated area. The following specifics
apply:
a. Advance party or reconnaissance team did not detect contaminated area.
b. Templating (NBC 5 Report) did not accurately depicit the boundaries of the contaminated area.
c. Enemy forces executed attack after reconnaissance was completed.
d. Maneuver element or unit enters contaminated area unexpectedly.
Platoon/Company Actions Battalion/Task Force Actions
1. After recognizing the unit is in a contaminated area: 1. Receive initial report from the maneuver element and:
a. Elements halt. a. Plot coordinates on situation map.
b. Don protective equipment (MOPP suit, mask . . . b. Prepare NBC 4 Contact Report and sent to higher
etc). and adjacent units.
c. Each soldier performs personal wipedown, if c. Provide any guidance and/or assistance as possible
required. to maneuver element.
d. Chemical casualties are identified and treated. d. Inform commander and/or S3 of situation.
e. Alert other maneuver elements and higher that e. Monitor progress of maneuver element until
contamination has been found. element has safely transverse area.
f. If element is in direct-fire contact, continue mission 2. Report coordinates of bypass route to higher.
and fight dirt y. If not, proceed with remaining 3. Inform commander and/or S3 of the bypass route, and
steps. status of maneuver element.
g. Using the M256 Kit or other detection devises, 4. Coordinate for:
check immediate area for type and amount of a. Medical evacuation, if required.
contamination. b. Decontamination support, at earliest possible time.
NOTE: First “clean” element has found the initial c. Replishment of chemical defense equipment (CDE)
near side of the contamination. for maneuver element.
2. Element in contaminated area will continue forward d. Further reconnaissance of contaminated area.
checking area every 500 meters.
3. Based on METT-T, the maneuver element
commander determines which direction the element
should move to exit and bypass contaminated area.
4. The first “clean” element, based on the commanders
assessment, will move 500 meters to the rear to
establish the initial rear side line. Then the element
will:
a. Turn 90 degrees (left or right) and move 500
meters.
b. Halt, and check for contamination.
c. If contaminated, turn 90 degrees and move 500
meters to the rear.
d. Check for contamination. If no contamination is
found, turn 90 degrees in the original direction of
travel and move 500 meters. Check area again for
contamination.
e. Continue process in 4a - d until initial far side line
of contamination is crossed.
5. Element finding the initial far side line, or bypass
route, should clearly mark the route using either:
a. VS-17 panels.
b. Colored Smoke.
c. Guides.

A-13
FM 3-3

Platoon/Company Actions (Continued)

6. Once maneuver unit has safely transverse
contaminated area:
a. Report coordinates of bypass route to higher and
adjacent units.
b. Report casualties and request for medical
extraction, if required.
c. If mission permits, conduct vehicle spraydown and
MOPP gear exchange or unmasking procedures
(which ever is most appropriate, depending on
extent of contamination).
d. Request decontamination support from higher HQ
at earliest possible time.
e. Continue mission.

A-14
 FM 3-3

Platoon Through Brigade Task Force

Chemical or Biological Checklist
Situation: The commander directs the unit to respond to a civilian chemical accident or incident. The following
specifics apply:
a. Enemy operatives, agents or an attack has created damage to civilian chemical or biological facilities or
production plant(s).
b. Tactical operations has caused the unexpected or unintentional release of chemical or biological material (solid,
liquid, or gas) into the environment.
Platoon/Company Actions Battalion/Task Force Actions
1. Alert higher, adjacent and lower units. 1. Alert higher, adjacent and lower units.
2. Immediately secure the area and: 2. Ensure security and downwind hazard zones are
a. Start continuous monitoring, with the M256 Kit or established and:
similiar detection devise. Ensure results are a. Casualties are evacuated.
reported using NBC 4 Chemical Report format. b. Request assistance from:
b. Assume MOPP 4. (1) Military Police.
c. Establish security zone around the area of no less (2) Medical personnel.
than 620 meters radius. This area may be enlarged (3) EOD teams (if required).
depending on chemical agent involved. (4) Division Chemical section.
d. Evacuate casualties from security zone. Casualties (5) Host Nation support.
should be considered as contaminated and should (6) DOD response teams..
be contained in one central location. Initiate 3. If hazard is in vapor form plot a Type A Case b for
emergency decon of personnel. plotting purposes. Ensure friendly units and civilians
e. Identify witnesses for questioning. in the predicted downwind hazard area are warned- If
f. Establish a 10 km downwind hazard zone from the the hazard is in a liquid form, with no evaporation
perimeter of the security zone. All personnel hazard present, the 620 meter security zone should be
within this zone must don MOPP4 or evacuate the adequate.
area until further notice. 4. Maintain security of area
3. Maintain security until released by higher.

A-16
FM 3-3, C1

Appendix B
Biological Agents
Potential biological warfare agents and their effects
are depicted in Table B-1 below.

B-O
FM 3-3, C1

B-1
 FM 3-3, Cl

B-2
FM 3-3

B-3
FM 3-3

B-4
FM 3-3

B-5
FM 3-3

This section defines current country codes. Columbia CO

Geographical areas are listed in alphabetical order. Comoro Islands (Including Mayotte) CN
These codes are used inconjunction with the biological Congo CF
sampling form depicted in Appendix C. Cook Islands (Including Society Islands) CW
Costa Rica CS
Cuba CU
COUNTRY COUNTRY Cyprus CY
CODE Czechoslovakia CZ
Denmark DA
Afghanistan AF Djibouti DJ
Albania AL Dominica DO
Algeria AG Dominican Republic DR
American Samoa AQ Equador EC
Andorra AN Egypt EG
Angola AO El Salvador ES
Anguilla AV Equatorial Guinea EK
Antarctica AY Ethiopia ET
Antigua AC Faeroe Islands FO
Argentina AR Falkland Islands (Islands Malvinas) FA
Australia (Including Ashmore, Cartier and Coral Fiji FJ
Sea Islands Territory) AS Finland FI
Austria AU France (Including Corsica) FR
Bahamas,The BF French Guiana FG
Bahrain BA French Polynesia FP
Bangladesh BG French So. and Antarctic Islands FS
Barbados BB Gabon GB
Belgium BE Gambia GA
Belize BH Germany, Federal Republic (FRG) GE
Benin (Formerly Dahomey) DM Ghana GH
Berlin WB Gibraltar GI
Bermuda BD Gilbert and Ellis Islands (Including Phoenix,
Bhutan BT Central and Southern Line Islands) GS
Bolivia BL Greece GR
Botswana BC Greenland GL
Bouvet Island BV Grenada GJ
Brazil BR Guadaloupe GP
British Indian Ocean Territory IO Guam GQ
British Solomonl stand BP Guatemala GT
British Virgin Islands VI Guinea GV
Brunei BX Guinea-Bissau PU
Bulgaria BU Guyana GY
Burma BM Haiti HA
Burundi BY Heard Island and McDonald Islands (Including
Cameroon CM Kerguelen, Prince Edward and Croizet Islands) HM
Canada CA Honduras HQ
Cape Verde CV Hong Kong HK
Cayman Islands CJ Hungary HU
Central African Republic CT Iceland IC
Chad CD India (Including Sikkim, Laccidive, Andam and
Chile cl Nicobar Islands) IN
China CH Indonesia ID
Christmas Island KT Iran IR
Cocos (Keeling Islands) CK Iraq IZ

B-6
 FM 3-3

Iraq-Saudi Arabia Neutral Zone IY Norfolk Island NF

Ireland El Norway NO
Israel Is Oman (Including Kuria Mauria Island) MU
Italy IT Pakistan (Including Jammu and Kashmir] PK
Ivory Coast Iv Panama PM
Jamaica (Including Morant Island and Pedro Cayo Papua New Guidea PP
Island) JM Paracel Islands PF
Japan JA Paraguay PA
Johnston Atoll JQ Peru PE
Jordan JO Philippines RP
Kampuchea (Formerly Cambodia) CBW Pitcairn Islands Pc
Kenya KE Poland PL
Korea, Democratic People’s Republic KN Portugal (Including Azores Islands and Madeira
Korea, Republic of KS islands) PO
Kuwait KU Puerto Rico RQ
Laos LA Qatar QA
Lebanon LE Reunion RE
Lesotho LT Romania RO
Liberia LI Rwanda RW
Libya LY St. Christopher-Nevis Sc
Liechtenstein LS St. Helena (Including Ascension and Tristan da
Luxembourg LU Cunha Islands) SH
Macao MC St. Lucia ST
Madagascar (Malagasy Republic) MA St. Pierre and Miquelon SB
Malawi Ml St. Vincent VC
Malaysia MY San Marino SM
Maldive Islands MV Sao Tome and Principe TP
Mali ML Saudi Arabia SA
Malta MT Senegal SG
Martinique MB Seychelles (Admiralty, Aldabra and
Mauritania MR Assumption) SE
Mauritius (Including Chagos Island and Rodriguez Sierra Leone SL
Island) MP Singapore SN
Mexico MX Somalia SO
Midway Islands MQ South Africa SF
Monaco MN Spain (Including Balearic Islands, Canary Islands,
Mongolia MG Spanish North Africa, and Ifni) SP
Montserrat MH Spratly Islands PG
Morocco MO Sri Lanka CE
Mozambique MZ Sudan SU
Namibia WA Surinam NS
Nauru NR Svalbard and Jan Mayen Islands JS
Navassa Island BQ Swaziland WZ
Nepal NP Sweden SW
Netherlands NL Switzerland SZ
Netherlands Antilles Islands NA Syria SY
New Caledonia NC Taiwan (Including Pescadores Islands) TW
New Herbrides NH Tanzania (Including Zanzibar and Pemba
New Zealand NZ Islands) TZ
Nicaragua NU Thailand TH
Niger NG Togo TO
Nigeria NI Tokelau Islands TL
Niue NE Tonga TN

B-7
FM 3-3

Trinidad and Tobago TD Vatican City VT

Trust Territory of the Pacific (U.S. including Venezuela VE
Caroline Islands) TQ Vietnam VM
Tunisia TS Virgin Islands (U. S.) VQ
Turkey TU Wake Island WQ
Turks and Caicos Islands TK Wallisand Futuna Islands WF
Tuvalu TV Western Sahara WH
Uganda UG Western Samoa WS
United Artab Emitrates TC Yemen, North (YAR) YE
United Kingdom UK Yemen, South (PDRY) YS
USSR (East of 100 degrees) UR Yugoslavia YO
USSR (West of 100 degrees) UW Zaire CG
U.S. (Miscellaneous Pacific Islands) IQ Zambia ZA
UpperVolta UV Zimbabwe ZI
Uruguay UY

B-8
 FM 3-3

Glossary
A
ABCA allies - American, British, Canadian, and available
Australian allies Minimum safe distance - Distance corresponding to a
Active defense measures - Measures taken to find and degree of protection needed to remain in the area.
destroy either the munitions or the delivery systems of MOPP gear - Protective clothing and equipment worn
an NBC attack. appropriate to the threat, work rate imposed by the
ADA - Air defense artillery mission, temperature, and humidity.
APC - Armored personnel carriers MSD - Minimum safe distance
Arthropods - Group of invertebrate animals that have a
jointed body and legs such as insects, arachnids, and N
crustaceans. NATO - North Atlantic Treaty Organization
AWS - Air weather service NAV CDM - U.S. Naval Chemical Downwind Message
NBC - Nuclear, biological and Chemical
C NBCC - NBC center
CAT - Cloud arrival time. Used for biological agent NBCWRS - NBC warning and reporting system
calculations.
CB - Chemical/biological O
CDM - Chemical downwind message OPSEC - Operational security
CET - Cloud exposure time. Used for biological agent OPORD - Operational order
calculations. OPLAN - Operations plan
CFA - Covering force area OPCON - Operational control
CHEMWARN - Friendly chemical attack warning
COMMZ - Communications zone P
Passive defense measures - Measures taken to reduce
E possibilities of (or effects of) NBC attack.
ECM - Electronic countermeasures Pathogens - living microorganisms that cause disease in
ECCM - Electronic counter-countermeasures man, animals, or plants.
EW - Electronic warfare POW - prisoner of war
F S
FDC - Fire direction centers SIGSEC - Signal security
FEBA - Forward edge of the battle area SOP - Standing operating procedures
PLOT - Forward line of troops
FSE - Fire support element T
FSOP - Field standing operating procedures TARR - Time of arrival
Toxins - Poisonous substances produced as by-products
G of microorganisms (the pathogens), plants, and
GN - Grid north. animals.
GMT - Greenwich Mean Time
GZ - Ground zero U
Universal transverse mercator - Meridians and
K parallels of latitudes appearing lines crossing at right
km - Kilometer angles.
USMC - United States Marine Corps
M USMTF - United States Message Text Format
METT-T - mission, enemy, terrain, troops, and time UTM - Universal transverse mercator

Glossary-1
FM 3-3, C1

References
Related Publications
Related publications are sources of additional information. Users do not have to
read them to understand FM 3-3, JCS Publication 25, United States Message Text
Format (USMTF) Program.
Army Regulations (AR)
31025 Dictionary of US Army Terms
310-50 Catalog of Abbreviations and Brevity Codes
350-41 Nuclear, Biological and Chemical Defense and Chemical Warfare
Field manuals
3-3-1 Nuclear Contamination Avoidance
3-4 NBC Protection
3-5 NBC Decontamination
3-6 Field Behavior of Chemical Agents
3-7 NBC Handbook
3-9 Military Chemistry and Chemical Compounds (AFR 355-7)
3-19 NBC Reconnaissance
3-50 Deliberate Smoke Operations
3-100 NBC Operations
6-15 Field Artillery Meteorology
7-7 The Mechanized Infantry Platoon and Squad (APC)
8-9 NATO Handbook on the Medical Aspects of NBC Defensive Operations
(AMED P-6; NAVMED P-5059; AFP 161-3)
8-33 Control of Communicable Diseases in Man
8-285 Treatment of Chemical Agent Casualties and Conventional Military
Chemical Injuries
11-50 Combat Communications Within the Division (How to Fight)
17-95 Cavalry (How to Fight)
20-33 Combat Flame Operations
21-60 Visual Signals
21-305 Manual for Wheeled Vehicle Driver
22-100 Military Leadership
23-9 M16A1 Rifle and Rifle Marksmanship
23-31 40mm Grenade Launchers M203 and M79
23-67 Machinegun, 7.62-mm, M60
24-1 Combat Communications
24-18 Tactical Single-Channel Radio Communications Techniques
27-10 The Law of Land Warfare
30-16 Technical Intelligence
34-1 Intelligence and Elekctronic Warfare Operations
34-3 Intelligence Analysis
71-1 Tank and Mechanized Infantry Company Team (How to Fight)
90-2 Tactical Deception (How to Fight)
90-3 Desert Operations (How to Fight)
90-5 Jungle Operations (How to Fight)
90-6 Mountain Operations (How to Fight)
90-10 Military Operations on Urbanized Terrain (MOUT) (How to Fight)
100-5 Operations (How to Fight)

References-0
 FM 3-3, C1

101-5 Staff Organization and Procedures

Soldier Training Publications (STP)
3-54B-TG Trainer’s Guide for MOS54B, NBC Specialist
3-54B1-SM Soldier’s Manual for MOS 54B, NBC Specialist (Skill Level 1)
3-54B2-SM Soldier’s Manual for MOS 54B, NBC Specialist (Skill Level 2)
3-54B34-SM-TG Soldier’s Manual and Trainer’s Guide for MOS 54B, NBC Specialist
(Skills Levels 3 and 4)
21-1 Soldiers Manual of Common Task (Skill Level 1)
21-2 Soldiers Manual of Common Task (Skill Levels 2, 3, and 4)
Department of the Army Forms (DA Forms)
1971-2-R Chemical Data Sheet - Monitoring or Survey
Miscellaneous Publications
ATP 45- Volume II
TM 3-216 Technical Aspects of Biological Defense

References-1
FM 3-3

Index-0
FM 3-3

Index-1
FM 3-3

Index-2
 FM 3-3
FM/FM 11-17
16 NOVEMBER 1992

By Order of the Secretary of the Army:

GORDON R. SULLIVAN
General, United States Army
Official: Chief of Staff

MILTON H. HAMILTON
Administrative Assistant to the
Secretary of the Army
03147

By Order of the Marine Corps:

RONALD D. ELLIOTT
EXECUTIVE DIRECTOR
SYSTEMS COMMAND
U.S. MARINE CORPS

DISTRIBUTION:

Active Army, USAR, and ARNG: To be distributed in accordance with

DA Form 12-llE, requirements for FM 3-3, Chemical and Biological
Contamination Avoidance (Qty rqr block no. 3829)

✩ U.S. GOVERNMENT PRINTING OFFICE : 1994 0 – 300-421 (02278)

 C1, FM 3-3/FMFM 11-17

Change 1 HEADQUARTERS
DEPARTMENT OF THE ARMY
US MARINE CORPS
Washington, DC, 29 September 1994

Chemical and Biological Contamination Avoidance

FM 3-3/FMFM 11-17, 16 November 1992, is changed as follows:
1. New or changed material is indicate by a BAR ( ).
2. Distribution restriction statement identified on this change replaces the one shown on basic
publication dated 16 November 1992.
3. Remove old pages and insert new pages as indicated below:
4. File this transmittal sheet in front of the publication.
Remove Old Pages Insert New Pages
1-5 thru 1-6 1-5 thru 1-6
2-1 thru 2-2 2-1 thru 2-2
2-3 thru 2-4 2-3 thru 2-4
3-3 thru 3-4 3-3 thru 3-4
3-5 thru 3-6 3-5 thru 3-6
3-9 thru 3-10 3-9 thru 3-10
3-11 thru 3-12 3-11 thru 3-12
3-13 thru 3-14 3-13 thru 3-14
3-15 thru 3-16 3-15 thru 3-16
3-17 thru 3-18 3-17 thru 3-18
3-19 thru 3-20 3-19 thru 3-20
3-21 thru 3-22 3-21 thru 3-22
4-1 thru 4-2 4-1 thru 4-2
4-13 thru 4-14 4-13 thru 4-14
4-15 thru 4-16 4-15 thru 4-16
5-3 thru 5-4 5-3 thru 5-4
5-11 thru 5-12 5-11 thru 5-12
5-17 thru 6-0 5-17 thru 6-0
A-15 thru B-0 A-15 thru B-0
B-1 thru B-2 B-1 thru B-2
Glossary-1 thru Ref-0 Glossary-1 thru Ref-0
Ref-1 thru Index-0 Ref-1 thru Index-0
DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited.

MARINE CORPS PCN: 13971190001

By Order of the Secretary of the Army:

GORDON R. SULLIVAN
General, United States Army
Official: Chief of Staff

MILTON H. HAMILTON
Administrative Assistant to the
Secretary of the Army
07244

By Order of the Marine Corps:

CARL E. MUNDY, JR.

Commandant
United States Marine Corps

DISTRIBUTION:
Active Army, USAR, and ARNG: To be distributed in accordance with DA Form 12-11 E,
Requirements for FM 3-3, Chemical and Biological Contamination Avoidance, (Qtr rqr block 3829).
PIN: 031069-001