RCV 27MHz PCB

(Level C - assembled)

- PARTS LIST and ASSEMBLY INSTRUCTIONS

This is the Parts list for the "Level C" (assembled) Transmitter and Receiver PCBs, for the RADIO CONTROLLED VEHICLE. This is to be used in conjunction with the RCV Teaching unit. - The PCB layouts are in the RCV Teaching unit, and the Schematic diagrams at the end of this unit.
TRANSMITTER PARTS LIST RECEIVER PARTS LIST

REF NO.
PCB IC CRYSTAL TX TRANSISTOR Q1, Q2 DIODES D2 LED D1 INDUCTOR L1 L2 L3, L4 SW SW1 CAPACITORS C5 C4, C6, C10 C8, C9 C7 C1, C3, C2 RESISTORS R6, R8 R2 R1 R4 R5 R7 R3 ANTENNA BRACKET

SPECIFICATION
18701TX TX2B 27.145MHZ 2SC945 4.3V ZENER RED LED 5 mm 6R8K - 6.8H 1ROK - 1H 2R2K - 2.2H SLIDE 47P + - 5% 82P + - 5% 101P + - 5% 103Z 473Z

QTY
1 1 1 2 1 1 1 1 2 1 1 3 2 1 3

REF NO.
PCB IC TRANSISTOR Q1 Q2, 5, 8, 11, 14 Q9, Q12 Q10, Q13 Q4, Q7 Q3, Q6, Q15 DIODES D1 OSC COIL L1 CAPACITORS C1 C2 C3 C4 C5 C6, C10 C7 C8

SPECIFICATION
18701RX RX2B S9013 2SC945 B564A D471A C2328A 468 562 A928A 3.3V ZENER 7 1/2T 4P + - 5% 40P + - 5% M/C 332K 18P + - 5% 3.3F + - 10% 10 V 203 Z 473 Z 501P + - 10% 103 Z 222 Z 100F + - 10% 10 V 47 + - 5% 1/4W 82 + - 5% 1/4W 470 + - 5% 1/4W 680 + - 5% 1/4W 1K + - 5% 1/4W 3.3K + - 5% 1/4W 270K + - 5% 1/4W 330K + - 5% 1/4W 390K + - 5% 1/4W 3.9MK + - 5% 1/4W

QTY
1 1 1 5 2 2 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 2 2 1 1 6 3 1 1 1 2

PRINTED CIRCUIT BOARD INTEGRATED CIRCUIT

PRINTED CIRCUIT BOARD INTEGRATED CIRCUIT

100 + - 5% 1/4W 330 + - 5% 1/4W 470 + - 5% 1/4W 5.6 K + - 5% 1/4W 33 K + - 5% 1/4W 220 K + - 5% 1/4W 250 K + - 5% 1/4W

2 1 1 1 1 1 1

C9 C11 C13 RESISTORS R14, 16 R19, 21 R4 R1 R18, 13, 15, 17, 20, 22 R3, R6, R11

PARTS MOUNTED ON MOTOR CAPACITORS C14 (for M2) C15 (for M1) 473 Z 473 Z 1 1

R2 R12 R9 R7, R10

SCORPIO TECHNOLOGY VICTORIA PTY. LTD.

A.B.N. 34 056 661 422

17 Inverell Ave., Mt. Waverley, Vic. 3149

Tel: (03) 9802 9913

Fax: (03) 9887 8158

Revised: 2nd June 2009

www.scorpiotechnology.com.au

1. PCB ASSEMBLY
1.1 INSTRUCTIONS FOR TEACHERS
Constructing these PCBs is reasonably difficult. Ideally students need some previous experience at constructing and testing electronic projects. For this a good understanding of the various components and their symbols is useful. It is important that students understand the symbols and general principles of the various electronic components before they begin their project.

Resistors
Resistors are marked on the PCB as R1, R2, etc. Bend one lead of the resistor 180 as shown on the left. Insert the leads through the holes in the PCB until the body of the resistor rests just above or on the PCB.. Bend the leads out slightly on the track side. This will prevent the resistors from slipping down when the board is turned upside down during soldering. Use the colour code chart to determine the value of each resistor.
Resistance Preferred Notation 82R 100R 330R 470R 680R 1k 3k3 5k6 33k 220k 270k 330k 390k 3M9 Grey Brown Orange Yellow Blue Brown Orange Green Orange Red Red Orange Orange Orange

1.2 PCB CONSTRUCTION DETAILS

Both the transmitter and receiver PCBs have a silk screen overlay, which is printed on the PCBs, to locate the components. Assembly Before soldering, all components must be checked to make sure theyre correctly placed. The components are soldered. The component leads must be trimmed 1 to 2 mm from the PCB. Note: Before applying power, check soldering for "dry joints" and solder bridges across tracks. Tuning The prototype PCB's were found to work without adjusting the receiver tuner L1. If adjustment is needed, use a small plastic rod with the end pointed like the end of a screwdriver. Make sure that metal screwdrivers are not used. Any metal (even brass) will affect the adjustment. Transistors Be very careful that the numbers marked on the transistors are the same as on the parts list. Note: They may look the same, but if they are swapped around the PCB will not work. Integrated Circuits These components look like beetles with lots of legs! They have a notch (or dimple) at one end. These must be placed on the PCB with the notch facing in the same direction as shown on the PCB. If power is connected to the PCB with these facing the wrong way, the PCB will not work and the Integrated Circuit will be permanently damaged.

82 Ohm 100 Ohm 330 Ohm 470 Ohm 680 Ohm 1k Ohm 3.3k Ohm 5.6k Ohm 33k Ohm 220k Ohm 270k Ohm 330k Ohm 390k Ohm 3.9M Ohm

Red Black Orange Violet Grey Black Orange Blue Orange Red Violet Orange White White

Black Brown Brown Brown Brown Red Red Red Orange Yellow Yellow Yellow Yellow Green

The resistors values are marked with coloured bands. These are the resistor colour codes. The coloured bands for are given below.
0 - Black 1 - Brown 2 - Red 3 - Orange 4 - Yellow 5 - Green 6 - Blue 7 - Violet 8 - Grey 9 - White 20% - No stripe 10% - Silver stripe 5% - Gold stripe

Capacitors
There are 3 types of capacitors used: Disk Ceramic These are like a round disk with two leads. They can be placed either way round. The value is marked on one side. The codes that are marked are shown below.

10pF 15pF 47pF 82pF 100pF 500pF 2.2nF 10nF 20nF 47nF

10 15 47 82 100 or 101 500 or 501 222 103 203 473

The negative lead goes to the end that D1s arrow symbol (on the PCB) points towards.

Zener Diode
D1 is a 4.2v or 4.3v Zener diode. It has 4v2 or 4v3 marked on its body. A magnifying glass will probably be needed to read it. The diode has a black band on one end. This end corresponds to the end that D2s arrow symbol points towards. - this must be mounted in the correct direction.

Electrolytic These have a cylindrical body with a stripe down one side. The stripe indicates the negative terminal and they must be connected correctly or the PCB will not work.

Crystal
The crystal has a bright metal body with 27.125 marked on it, and can be connected either way.

1.4 RECEIVER
Zener Diode
D1 is a 3.3v Zener diode. It has 3v3 marked on its body. A magnifying glass will probably be needed to read it. The diode has a black band on one end. This end corresponds to the end that D1s arrow symbol points towards. - this must be mounted in the correct direction.

Greencap (Metallised Polyester)

These are rectangular, usually green, and can be mounted either way round. The value is printed on one side. There is only one Greencap used in this project. It could be marked as either: 3.3nF: 332 or 0.0033F

Inductors

1.3 TRANSMITTER
The PCB has a large cut out hole in its centre.

Inductors
There are four inductors used. They look like large resistors. They are: - L1: Blue, Grey, Gold, Silver - L2: Brown, Black, Gold, Gold - L3 and L4: Red, Red, Gold, Silver The inductors can be mounted in either direction.

There are two types of inductors. This PCB uses only one type: L1 is a variable type. This has a plastic body with copper wire wound around its body. It will only fit on the PCB one way round.

Resistors
Position R22 is not marked on the PCB - its holes are directly between R3 C5 (to the right of R3)

Light Emitting Diode (LED)

This is used to indicate when the transmitter is on. The negative lead can be identified in one of three ways (although not all LEDs use methods 2 & 3. The methods are : 1. The flag (the larger connection inside the body) identifies the negative lead. This is visible when the LED is held up to the light 2. The shortest leg is negative 3. A flat on the ridge, around the base of the LED is on the negative side.

Transistors
A large number of transistors are used. Be careful that the numbers marked are the same as on the parts list. They may look the same, but if any are swapped around the PCB will not work. Connection positions for the transistors Q1(s9013) and Q5(2SC945) are marked different to the other transistors. Connect the leads as per marking, refer illustrations below.

2. WIRING UP THE PCBs

2.1 GENERAL:
After the PCBs have been assembled, a number of parts need to be connected to the PCBs. This section details what is connected, and where. - This unit must be used in conjunction with the RADIO CONTROL VEHICLE (Mark 3) Teaching unit. The picture of the reverse side of the PCB (ie. The PCB layout) provides soldering instructions for the PCBs. When soldering the wires, be careful to use a minimal amount of solder (to avoid overrun)

2.2

THE TRANSMITTER (CONTROL UNIT):

Use the 9 volt battery clip for the battery connection to the transmitter. An On/Off switch is mounted on the PCB, and soldered in place this is the Transmitters On-Off switch, and is an integral part of the PCB / kit. Note: A LED on the PCB is used to indicate when the unit is switched on.

THE TRANSMITTER PCB

Connect numbers marked on this drawing to the like numbered points on the 2 switches: SW2 and SW3. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. STEERING SWITCH - SW2 SW2 position 1 SW2 - position 2 SW2 - position 3 Battery clip ve (Black) Battery clip +ve (Red) SW3 position 6 SW3 position 7 SW3 position 8 SW3 position 9 SW3 position 10

FORWARD / REVERSE SWITCH - SW3

NOTE: Both switches are shown looking at their terminals (i.e. from the rear of the switch) WIRING INSTRUCTIONS Cut nine wires the same length. Three are for the steering switch (SW2) and the remainder for the Forward/ Reverse switch (SW3). Strip 5 mm off the insulation from both ends of the wires. Twist the bare strands together tightly. Tin one end of each wire. Cut the tinned ends of the wires back to about 3mm long. Tin the Printed Circuit Board pads, to which the switch wires will be soldered (refer the PCB illustration). Hold the tinned wire ends onto the tinned pads and heat both with the soldering iron (the solder on the wires and pads should melt into each other).

Put the un-tinned ends of the wires through the holes of the switch terminals. Solder the wires and cut off the excess wire as close to the terminal as possible. Note: Take care to ensure the Positive and Negative wires are the correct way round.

2.3

THE RECEIVER PCB (VEHICLE MOUNTED):

THE RECEIVER PCB

Connect the numbers marked on the PCB drawing to the following : PCB CONNECTIONS: 1. Steering motor 2. Steering motor 3. 4xAA Battery +ve (Red) 4. 2xAA Battery ve (Black) 5. To SW1 position 2 6. Drive motor 7. Drive motor via inductor L4 8. Antenna 9. 4xAA Battery ve (Black)

ON / OFF SWITCH - SW1: 1. To +ve (red) - 2x AA batteries 2. To 5 on the PCB

Soldering should be carried out in the following order: Wire the switch in place as shown in the diagram. Solder the switch, battery connections and antenna. Solder the wires to the motors (after testing the direction of the wheels rotation). NOTE: If you look at the Receivers Schematic diagram, you will see that the two sets of battery holders connect together. The +ve wire from the 4AA battery holder is connected to the ve wire of the 2AA battery holder. When the battery holders are connected this way, 9Volts are supplied to the control circuitry, and 6 volts are supplied to the motor section.

WIRING INSTRUCTIONS Cut the wires needed for the various PCB connections. Strip 5 mm off the insulation from both ends of the wires. Twist the bare strands together tightly. Tin one end of each wire. Cut the tinned ends of the wires back to about 3mm long. Tin the PCB pads, to which the switch wires will be soldered. Hold the tinned wire ends onto the tinned pads and heat both with the soldering iron (the solder on the wires and pads should melt into each other). Put the un-tinned ends of the wires through the holes of the switch terminals. Solder the wires and cut off the excess wire as close to the terminal as possible. Capacitors C14 and C15 are soldered directly across the terminals of the steering and drive motors to suppress RF interference one for each motor (Refer to the schematic diagram).

SCHEMATIC DIAGRAM - RECEIVER (27.125 MHz LEVEL C)

SCHEMATIC DIAGRAM -- TRANSMITTER (27.125 MHz LEVEL C)