FORWARD

This report is written by Zelalem Teshome Hika, and submitted as part of the requirements for
completion of Master degree in Offshore Structural Engineering at University of Stavanger
department of construction techniques and material technology. The terms of the assignment
is from January to June 2012
Offshore structures may be defined as structures that have no fixed access to dry land. Such
structures are highly exposed to environmental loadings, and required to withstand and
overcome all conditions.
The main purpose of offshore structural analysis is to ensure that all offshore operations shall
be performed in safe manner with respect to safety environment and economical risk.
The purpose of this thesis work is: Learn to use SESAM GeniE for modelling the geometry and loads of the topside
module.
Learn to use SESAM Presel, Prepost, Framework and Xtract for structural analysis
and reporting.
Evaluation and implementation of relevant rules for offshore construction.
Design and analysis of a module for relevant loads and control Phases such as
transport, installation and operation.
Optimize the frame/trusses configuration and selection of profile types to achieve
optimal design with respect to weight considering, inplace, lift and transport condition.
Local design of joints, lifting point and lifting pad eyes.
This master thesis has been carried out under the supervision of Rolf A. Jakobsen and
Associate professor Siriwardane, S.A.Sudath C at university of Stavanger.
I would like to express my gratitude to my principal supervisors Rolf A. Jakobsen and
Associate professor Siriwardane, S.A.Sudath C for their inspiration, follow-up and great
advices.
I would like to thank Aker Solutions for giving me the opportunity to work on my master
thesis with them and particularly I would like to express my deepest gratitude to my assistant
supervisor Johan Christian Brun for his support and wonderful inspiration throughout, in such
a way that I feel that I have gained greater understanding of this discipline.
I would like to thank also the rest of engineers in structural analysis group at Aker Solutions
for their friendly and great advices.
Finally I would like to thank my parents, brothers, sisters and friends for their support and
inspiration during my study.

Stavanger 14.06.2012
Zelalem Teshome Hika

SUMMARY
The structural analysis of a topside module presents many technical challenges that have to be
designed to overcome in efficient manner to meet a proper weight and strength control with
respect to all conditions
The primary purpose and goal of the structural design analysis and optimization of this master
thesis is to maintain proper weighed structure that has sufficient capacity and strength with
respect to transportation, installation and operation. Apart from that the design analysis and
optimization of this topside structure is to achieve a structure that has high safety with respect
to life, environment and economic risk.
On preparation of analysis hand calculation of wind load, center of gravity and barge
acceleration load were prepared.
During modeling, design analysis and optimization the following software tools were learned
and utilized.
SESAM GeniE for modeling the geometry and loads of the topside module
SESAM Presel, Prepost, Framework and X-tract for structural analysis and reporting
In addition the following issues were considered.
Evaluation and implementation of relevant rules for offshore construction;
Optimize the frame/trusses configuration and selection of profile types to achieve
optimal design with respect to weight considering, transport, inplace and lifting
conditions;
Design and analysis of the topside structure for relevant loads and control Phases;
Local design of joints, lifting point and lifting pad eyes.
The structural design and analysis are performed considering the inplace as the basic and first
stage of the process. Transport condition was second stage, considering barge accelerations,
wind and sea fastening. Failing members could indicate a need for temporary reinforcements.
All temporary reinforcements considered to be removed after the installation.
Lifting condition was the final stage. During lifting all temporary reinforcements will
naturally be present.
Local design and analysis of lifting padeyes was performed for padeye loading capacity of
1500 tons.
Local analysis of joints for selected critical joints for inplace and lift conditions are detailed
analysed and joints which had insufficient capacity were reinforced and analysed.
The results from the analysis reveal that the module has sufficient capacity to all design
conditions.
The local analysis results for lifting padeyes show that the lifting padeye has sufficient
capacity with respect to stresses in pin and eye, tensile stress next to the eye, shear stress in
the pad eye plate and weld strength. The local analyses of critical joints results reveal that all
critical joints have sufficient capacity with respect to design criteria and rules.

ii

ABBREVIATIONS
ALS
CoG
CoGE
CND
DAF
DC
DNV
FLS
HSE
IR
IDC
LC
Lbuck
MEL
MSF
MTO
NS
PSA
SDOF
SOP
SI
SKL
SLS
SMYS
SWL
UF
UFL
ULS
V Mises
WLL
WCF

Accidental Limit State

Centre of Gravity
Centre of Gravity Envelope
Operational, Storm or earthquake condition
Dynamic Amplification Factor
Design Class
Det Norske Veritas
Fatigue Limit State
Health Safety and Environmental
Interaction Ratio
Inter Discipline Check
Load Case
Length between lateral support of compression flange
Master Equipment List
Module Support Frame
Material take-off
Norsk Standard
Petroleum Safety Authority Norway
Single Degree of Freedom
Swinging Object Protection
System International
Skew Load Factor
Serviceability limit state
Specified Minimum Yield Strength
Still Water Level
Utility Factor
Unsupported Flange Length
Ultimate Limit State
Equivalent stress used in von Mises stress check
Working Limit Load
Weight Contingency Factor

iii

TABLE OF CONTENTS
FORWARD .............................................................................................................................................. i
SUMMARY ............................................................................................................................................ ii
ABBREVIATIONS ................................................................................................................................ iii
TABLE OF CONTENTS ....................................................................................................................... iv
1
INTRODUCTION .......................................................................................................................... 1
1.1
BACKGROUND ..................................................................................................................... 1
1.2
SCOPE..................................................................................................................................... 2
1.3
REPORT STRUCTURE ......................................................................................................... 2
2
DESIGN CONSIDERATIONS ...................................................................................................... 3
2.1
ANALYSIS METHOD ........................................................................................................... 3
2.2
DESIGN REQUIREMENTS AND CRITERIA...................................................................... 3
2.3
MATERIAL PROPERTIES .................................................................................................... 4
2.4
CROSS SECTIONS ................................................................................................................ 4
2.5
DESIGN ANALYSIS AND OPTIMIZATION PLAN ........................................................... 5
3
COMPUTER MODELLING .......................................................................................................... 6
3.1
GENERAL .............................................................................................................................. 6
3.2
COORDINATE SYSTEM ...................................................................................................... 6
3.3
UNITS ..................................................................................................................................... 6
3.4
MEMBER, JOINTS AND DECK PLATE MODELING ....................................................... 6
3.5
BOUNDARY CONDITIONS ................................................................................................. 7
3.6
CODE CHECK PARAMETERS ............................................................................................ 8
4
ACTION AND ACTION EFFECTS .............................................................................................. 9
4.1
DEAD LOADS........................................................................................................................ 9
4.2
LIVE LOADS........................................................................................................................ 10
4.3
ENVIRONMENTAL LOADS .............................................................................................. 10
4.3.1
WIND ACTIONS .......................................................................................................... 11
4.3.2
WAVE ACTIONS ......................................................................................................... 12
4.3.3
EARTHQUAKE LOADS ............................................................................................. 12
4.3.4
TRANSPORT ACCELERATION ................................................................................ 12
5
GLOBAL STRUCTURAL ANALYSIS AND OPTIMIZATION ............................................... 13
5.1
INPLACE CONDITION ....................................................................................................... 15
5.2
LIFTING CONDITION ........................................................................................................ 20
5.3
TRANSPORT CONDITION................................................................................................. 24
6
DESIGN PADEYES ..................................................................................................................... 28
6.1
LOCAL ANALYSIS OF PADEYES .................................................................................... 28
6.2
DESIGN CHECK OF PADEYES ......................................................................................... 29
7
DESIGN OF JOINTS ................................................................................................................... 32
7.1
LOCAL ANALYSIS OF JOINTS......................................................................................... 32
7.2
DESIGN CHECK OF JOINTS ............................................................................................. 32
8
DISCUSSION ............................................................................................................................... 34
9
CONCLUSIONS .......................................................................................................................... 36
REFERENCES ...................................................................................................................................... 38
APPENDIXES....................................................................................................................................... 39
A. GEOMETRY ................................................................................................................................ 40
B. JOINTS ......................................................................................................................................... 44
C. SECTION PROPERTIES ............................................................................................................. 48
D. ACTIONS ..................................................................................................................................... 53
E. GLOBAL ANALYSIS ................................................................................................................. 79
F. DESIGN CHECK OF PADEYES ................................................................................................ 99
G. DESIGN CHECK OF JOINTS ................................................................................................... 104

iv

INTRODUCTION

1.1 BACKGROUND
An offshore structure may be defined as a structure that has no fixed access to dry land and is
required to stay in position in all weather conditions. Major offshore structures support the
exploration and production of oil and gas from beneath the seafloor.
The design, analysis and construction of these structures are one of the most demanding sets
of tasks faced by engineering profession.
Offshore structures may be fixed to the seabed or may be floating. Floating structures may be
moored to the seabed, dynamically positioned by thrusters or may be allowed to drift freely.
Offshore structures should experience minimal movement to provide a stable work station for
operations such as drilling and production of oil and gas. Offshore structures are typically
built out of steel, concrete or a combination of steel and concrete, commonly referred to as
hybrid construction.
The environment as well as financial aspects offshore requires that a high degree of
prefabrication be performed onshore. It is desirable to design so that offshore work is kept to a
minimum.
The overall cost of an offshore man-hour is approximately five times that of an onshore manhour. The cost of construction equipment required to handle loads, and the cost for logistics
are also much higher in offshore. These factors combined with the size and weight of a
structure requires that the design must carefully consider all construction activities between
shop fabrication and offshore installation. Ref. [23]
This master thesis presents the global design analysis and optimization of an offshore topside
module which has a dimension of 40m x 20m x 20m length, width and height respectively.
The main goal of this master thesis is Optimization of structural member profiles and this
thesis illustrates the strategy and procedure of performing a design optimization of a topside
offshore module considering all the construction phases and design conditions.
Inplace, lifting and transport design analysis are performed using SESAM software package
for global analysis of the topside module.
Local analysis of lifting padeyes, lifting points and joints are also performed with hand
calculation and Excel software tools. The global and local analysis covers ULS and ALS
condition are carried out in accordance with prevailing design rules and standards.
The design of offshore structures has to consider various requirements of construction relating
to:
Weight
Load-out
Sea transport
Offshore lifting operations
Hook-up
Commissioning
1

The work performed in this report will be limited and concentrate on weight control, capacity
and optimizations of member for transportation, lifting and operating phases and local
analysis of lifting padeyes, lifting points and critical joints.
1.2 SCOPE
Learn to use SESAM GeniE for modelling the geometry and loads of the topside
module.
Learn to use SESAM Presel, Prepost, Framework and Xtract for structural analysis
and reporting.
Evaluation and implementation of relevant rules for offshore construction.
Optimize the frame/trusses configuration and selection of profile types to achieve
optimal design with respect to weight considering, transport, lifting and operating
conditions.
Design and analyse the module for relevant loads and control phases such as transport,
installation and operation.
Local design and analysis of lifting padeyes, lifting point and critical joints.
1.3 REPORT STRUCTURE
The structure must be designed to resist static and dynamic loads. Chapter 2 discusses the
general requirement of relevant techniques with respect to offshore structural design
consideration. Chapter 3 presents the systematic approach to model the structure. Chapter 4
presents all the basic loads on the module. Chapter 5 presents action combination and
structural analysis for inplace, lift and transport phases and global analysis the structure for all
construction phases. Chapter 6 presents the local lifting padeye analysis. Chapter 7 considers
methods of determining the static strength of local joint and analysis is performed and
presented. In chapter 8 the discussion part of the analysis and optimization are presented and
chapter 9 will presents the conclusion part of this thesis. References and Appendixes are
presented at the end of this report.

DESIGN CONSIDERATIONS

2.1 ANALYSIS METHOD

The module shall be analysed by use of the SESAM suit of programs, and includes the
following:
GeniE for geometry and load modelling
Pre-processor for modelling beam/shell/plate structure
Pre-processor for applying equipment loads and actions
Presel for super element assembly and load combining
Supper element and load assembly pre-processor
Use first level super elements created by GeniE to create higher order super elements
Assembles loads/actions from GeniE and create load combinations
SESTRA for stiffness calculations
Solve the finite element equations
Prepost for combining stiffness matrices and final load combinations
Conversion of finite element model, loads and results in to postprocessor data base elements
Framework for code checks
Code check unit and post processor for finite element analysis
Xtract for post processing
A post processor for presentation of results from static structural analyses
2.2 DESIGN REQUIREMENTS AND CRITERIA
Governing law and regulations is the PSA, Ref. [2]. The structural checks will be carried out
in accordance with NORSOK, Ref. [9] and [11], and Euro-code 3, Ref. [15].
The modules shall be code checked for following limit states:
ULS: Limit states that generally correspond to the resistance to maximum applied actions.
Action factors and action combinations with emphasis on ULS are given in chapter 5.
SLS: Limit states that correspond to the criteria governing normal functional use.
If not more stringent functional requirements specified otherwise, the following requirements
for vertical deflection should apply:
Deck beams: Maxdeflection L/200 Beams supporting plaster or other brittle finish Maxdeflection
L/250 Reference is also made to section 7.2.4 of NORSOK N-001, Ref. [9]. For the
analyses performed, maximum deflection of L/250 is applied.

2.3 MATERIAL PROPERTIES

The steel qualities used in the analysis are presented and the strength reduction due to larger
thicknesses (>40mm) shall be according to prevailing standards.
In general, the structural steels applied have the following steel properties and qualities:
Yield strength
Plates
420 MPa
Sections

420 MPa (Welded profiles)

355 MPa (Standard profiles

Further reference is made to [6], [7] and [8]

Any new steel shall comply with requirements set out in the NORSOK standards.
The design resistance shall be determined based on the characteristic values of material
strength reduced by the material factor in accordance with section 7.2 of NORSOK N-001,
Ref. [9]
The following material properties are considered for all steel profiles:
Youngs modulus
Shear modulus
Density
Poissons ratio

E = 210000 N/mm2
G = 80000 N/mm2
= 7850 kg/ m3
= 0.3

MATERIAL FACTOR
Values of material factors can be taken as 1.0 except for ULS in which the following value is
applied:

1.15 for Structural Steel detail

2.4 CROSS SECTIONS

Loading orientation on the structural member usually influence the selection of section profile
types of the structural members. For this topside structural module, HEB and Square hollow
sections with hot rolled and cold welded profile will be considered.
HEB profile type is most widely used for floor beams and columns because these profiles
have great efficiency in transverse loading.
Rectangular tubes designed as rectangular hollow section widely used for column members
because of their efficiency in axial compression and torsion. Selection of the structural
member is considered the theory behind the structural member responses during transvers
loading and axial loading.
Global analysis of the topside structure will be performed and member utilization factors are
checked. Optimizations are performed for all construction phases. The final selected section
properties of profile types are presented in Table 5-15

The general geometry and member names of the module is presented in Appendix A, joints
names in Appendix B and all sections applied are presented in Appendix C
2.5

DESIGN ANALYSIS AND OPTIMIZATION PLAN

The analysis and optimization plan presented below shows the strategy to overcome
optimized and well-integrated structure for inplace, lifting and transport condition.

COMPUTER MODELLING

3.1 GENERAL
The module is modeled and analyzed by use of SESAM suit of programs.
3.2 COORDINATE SYSTEM
The coordinate system is used is such that Y is pointing North, X is pointing East, Z is
pointing upwards.
3.3 UNITS
The fundamental units (database unites) that used in the analyses are the following SI unites
or multiples of:
Length: meter (m)
Mass: tonne (T) (103kg)
Time: seconds (s)
The resulting force and stresses will then be Mega Newton (MN) and MN/m2 (MPa)
Input units to SESAM GeniE (pre-processor) are as follows:
Length:
Mass
Time:
Force:

meter (m)
tonene (T)
second (s)
kilo Newton (kN)

3.4 MEMBER, JOINTS AND DECK PLATE MODELING

A systematic approach to member and joint names will be adopted in the SESAM analyses.
Joint/Point names
Structural joints will have names starting with the letter J for joints and P for points, plus a six
digit number system as follows:
Jxxyyzz
(joint)
Pxxyyzz
(point)
Where xx,yy and zz are numbers in the range between 00 and 99 indicating the position of the
joint/point in the modules coordinate system.
Member names
Member names will start with the letter M and used the following notation:
Mxxyyzz
Where: xx, yy and zz are numbers in the ranger between 00 and 99 corresponding to end 1
joint number. D may be used for dummy elements instead of M. is a letter according to the
direction of the member:
X- x-direction
Y- y-direction
Z- z-direction
6

A
B
C
D
E
F

-Brace in the xy-plane running in the positive x-and positive y-direction

-Brace in the xy-plane running in the positive x-and negative y-direction
-Brace in the xz-plane running in the positive x-and positive z-direction
-Brace in the xz-plane running in the positive x-and negative y-direction
-Brace in the yz-plane running in the positive y-and positive y-direction
-Brace in the yz-plane running in the positive y-and negative z-direction

Deck members and columns running in the parallel with the axis system shall always run in
the positive direction. Direction of braces shall be such that the x-direction predominate the ydirection, which again predominates the z-direction. I.e. braces in xy- and xzplane shall
always run in positive x-direction, while braces in the yz-plane shall run in positive ydirection.
Plate names
Deck plates will have the following notation:
PLxxyyzz
Where: xx,yy and zz corresponds to the start joint of the plate. The start joint shall be the
lower left corner of the plate with the following joints defined in the counter clockwise
direction.
Joint modeling
Increased stiffness inside joint will in general be neglected, for large prefabricated nodes (e.g.
support nodes) the joint stiffness may be simulated by use of separate elements with increased
stiffness (dummy members). The stiffness of the dummy element shall be evaluated in each
case.
Plate modeling
4- noded quadrilateral shell elements is used to simulate the in-plane shear stiffness of the deck
structures. The plate elements shall not contribute to the strong axis bending stiffness of the deck
girder and will therefore be modeled at the center of the deck girders (the system lines)

Only the shear stiffness of the plate is accounted for in the global module analyses. This is
achieved by use of anisotropic shell element formulation and dividing the x-and ycomponents of the elements stiffness matrix by a large number (100 is used).
3.5 BOUNDARY CONDITIONS
The module is subjected to a two-step analysis.
Step one
Comprise dead load only, representing the condition at installation. The boundary conditions
at this stage is statically determined; i.e., no constraint forces will be a strain on the structure
Step two
Step two represents the boundary conditions in operating and transport phases. This means
that all the module supports are pinned, i.e. fixed for translation in all three directions. All
live-, variable- and environmental loads are applied in this step.

3.6

CODE CHECK PARAMETERS

Code check of members is performed for ULS-a/b by use of SESAM Framework. Member
checks (yield and stability) are performed according to NS3472, NORSOK N-004 and Eurocode 3.
Material Factor
The material factor (m) for structural steel members is 1.15 for ordinary ULS analysis.
Buckling Length Factor(Ly, Lz)

All members will be given default buckling length factor 1.0. However, booking may be set
manually if considered relevant.
Buckling Length

The default buckling length (Ly, Lz) is equal to the member length.
For members being modeled by several elements, the buckling lengths (Ly and Lz) may be
adjusted to the distance between the actual restraints. For deck beams with top flange being
restrained by the deck plate the buckling length for in-plane buckling can be set to a small
length, i.e. 0.1L
Unsupported Flange Length (UFL)

The unsupported length of the compression flanges shall be modeled for lateral buckling
checks of beams and girders. The default UFL is equal to the length of the element. For deck
beams with top flanges being supported by a deck plate and where it can be demonstrated that
the bottom flanges are in tension for all design cases, the UFL may be set to a small length to
suppress the lateral buckling check

ACTION AND ACTION EFFECTS

A load numbering system is common for this topside module, and applied to first level super
elements. The outline of numbering system is presented in Table 4-1
Load case
Description
1-10
Permanent loads representing steel weight
20-27
Permanent loads present at all control phases
31-34
Content weight (mechanical, piping, HVAC, etc.)
50-55
Wind loads
101-134
Horizontal acceleration loading, x-direction
201-234
Horizontal acceleration loading, y-direction
Table 4-1 Outline of the numbering system
4.1 DEAD LOADS
The dead loads include weight of structure, equipment, bulk and other items which form a
permanent part of the installation.
Dead load or permanent load can usually be determined with high degree of precision. Hence,
the characteristics value of a permanent load is usually taken as the expected average based on
actual data of material density and volume and material.
The weight contingency of 1.10 is applied to all permanent loads included as part of the
permanent weight.
The structural weight comprises primary, secondary and outfitting steel. Secondary and out
fitting steel will be a percentage of the primary steel weight, unless a specific weight is
defined.
On preparation of load modeling the total module weight was estimated to be about 2000T.
The module ended up with a total un-factored weight of 1609.30T, split into various
disciplines and deviations of the expected weight are listed in Table 4-2 below.
Basic dead load and live load generated from GeniE input data and SESTRA output are
presented in Appendix D. the dead loads distribution is presented in Table 4-1.

Discipline
Various equipment
Electrical Dry Weight
Instrumental Dry Weight
Piping Dry Weight
HVAC
Safety Dry Weight
Surface Dry Weight
Architectural Dry weight
Self Generated Dead Weight
Secondary Steel
Outfitting Steel

Relative
20.9 %
3.9 %
1.5 %

Actual Deviation
336 1.994378
62

-0.59895

24 0.726758

12.4 %

200

-0.28868

1.7 %

28

-0.55598

1.7 %

28

-0.40797

0.7 %

12

-0.65465

3.0 %

48

-0.56831

36.1 %

580.9

14.4 %

232.3

-0.27476

3.6 %
100.0 %

58.1
1609.3

-0.47408

Table 4-2 Load distribution

9

4.2

LIVE LOADS

Live loads or variable functional loads are associated with use and normal operation of the
structure
The live loads that usually must be considered are
Weight of people and furniture
Equipment and bulk content weights
Pressure of contents in storage tanks
Laydown area and live load on deck
The choice of the characteristic values of live load is a matter of structure. In general
inventory and Equipment Live Loads shall be taken from the Master Equipment List and/or
Weight Report and be distributed according to reported CoG coordinates but on this report the
weight distribution is taken from Aker solutions list of weight report.
There is always be a possibility that live load will be exceeded during life time of the
structure. The probability for this to happen depends on the life time and the magnitude of the
specified load. In general during the course of the life of the platform, generally all floor and
roof areas can be expected to support loads additional to the known permanent loads.
Variable deck area actions are applied in the structural check to account for loose items like
portable equipment, tools, stores, personnel, etc. Deck area actions are applied in accordance
with NORSOK, N-001 Ref. [9]
4.3

ENVIRONMENTAL LOADS

Environmental loads, is associated with loads from wind, snow, ice and earthquake. Within
the design of offshore structures wave and current loads also belongs to this group.
For wind and snow statistical data are available in many cases. In connection with the
determination of characteristic load, the term mean return value is often used. This is the
expected number of years between a given seasonal maximum to occur.
Offshore structures are highly exposed to environmental loads and these loads can be
characterized by:

Wind speed and air temperature

Waves, tide and storm surge, current
Ice (fixed, floes, icebergs)
Earthquake

10

4.3.1 WIND ACTIONS

The wind load which is applied on the structure is based on static wind load and basic
information is presented below.
Reference wind speed applied on a module is the 1-hour, all year Omni directional wind
speed at 10m above LAT:
U1h, 10m, 1y = 25.5 m/s
U1h, 10m, 10y = 29.5 m/s
U1h, 10m, 100y = 34.0 m/s
The global ULS inplace analyses will be based on the 3-second gust wind (L < 50m). Local
checks, if applicable, of stair towers, crane, wind cladding, etc. should be based on the 3-sec
gust wind.
For simplicity the wind load in the module analyses will be based on a constant wind speed at
an elevation located of the module height.
The static wind load is calculated in accordance to NORSOK N-003 section 6.3.3. For
extreme conditions, variation of the wind velocity as a function of height and the mean period
is calculated by use of the following formulas:
The wind loads are calculated by the following formula:
F = Cs A Um2 sin ()

Where:
=1.225 kg/m3
Cs
A
Um2

mass density of air

shape coefficient shall be obtained from DNV-RP-C205,
area of the member or surface area normal to the direction of the force
wind speed
angle between wind and exposed area

The characteristic wind velocity u (z,t)(m/s) at a height z(m) above sea level and
corresponding averaging time period t less than or equal to t0 = 3600 s may be calculated as:
U(z,t) = Uz [1-0.41Iu(z) ln (t/t0)]
Where, the 1 h mean wind speed U(z)(m/s) is given by
U(z) = U0[1+C ln(z/10)]
C = 5.73 * 10 -2 (1 + 0.15 U0) 0,5
Where, the turbulence intensity factor Iu (z) is given by
Iu(z) =0.061[1+0.043U0](z/10)-0.22
Where, U0 (m/s) is the 1 h mean wind speed at 10m

11

The wind load calculations performed for operational and transport phases are presented in
Appendix D.

4.3.2 WAVE ACTIONS

Wave load is not relevant for structures positioned higher than 25 meter above sea level. It is
considered that the module presented on this report has sufficient height above sea level to
avoid direct wave loading.
4.3.3 EARTHQUAKE LOADS
Structures shall resist accelerations due to earthquake. The 100 year earthquake accelerations
for this topside structure are 0.051g horizontal and 0.020g vertical. Ref. [18]
Accidental earthquake condition is also considered for inplace design and the values are
presented in Table 4-3 below.
Earthquake load
100 years
X direction
0.051g
Y direction
0.051g
-Z direction
0.020g
Table 4-3 Earthquake acceleration

10000 years
0.245g
0.255g
0.061g

Earthquake with annual probability of 10-2 can be disregarded according to NORSOK N-003
Section 6.5.2 Ref. [10]
4.3.4 TRANSPORT ACCELERATION
The transport analysis will consider ULS-a/b load conditions with module dry weight
(including temporary reinforcement), CoG shift factor, transport accelerations and wind.
Wind loads and accelerations are applied in eight directions at 45 degrees interval covering
the complete rosette, and is presented in Figure 4-1.

Figure 4-1 Directions of horizontal accelerations and wind

The barge acceleration is calculated according to Noble Denton Ref. [20] and detail calculation
is presented in appendix D. Result are presented in Table 4-4
DIRECTION
ACCELERATION
X
1.054g
Y
0.662g
Z
0.200g
Z
-0.200g
Table 4-4 Barge motion acceleration

12

GLOBAL STRUCTURAL ANALYSIS AND OPTIMIZATION

The aim of structural design analysis is to obtain a structure that will be able to withstand all
loads and deformations to which it is likely to be subjected throughout its expected life with a
suitable margin of safety. The structure must also fit the serviceability requirements during
normal use.
The various performance and use requirements are normally specified in terms of LIMIT
STATES. For steel structures the limit states may be categorized as follows:
Ultimate limit states (ULS), corresponding to the maximum load carrying capacity.
Fatigue limit states (FLS), related to the damaging effect of repeated loading.
Serviceability limit states (SLS), related to criteria governing normal use and durability.
Accidental limit states (ALS), corresponding to accidental moments during operation.
The design of structure may be divided into three stages. These are:
Functional planning
This problem in design is the development of a plan that will enable the structure to fulfill the
purpose for which it is built.
Cost estimate
Tentative cost estimate are developed for several structural layout
Structural analysis
Selection of the arrangement and sizes of the structural elements are decided so that the
service loads may be carried with a reasonably factor of safety.
Offshore structures are not fabricated in their final in-service position. Therefore, a detail
design must consider the following stages:

Fabrication and erection

Load out from fabrication yard to barge
Transportation from yard to offshore site on a barge
Lift from barge to final position
Inplace operating and accidental conditions

It is necessary to consider all accidental stages as different members may be critical in

different cases. In practice, the first two cases will be checks of the structure whereas the
transport, lifting and operating conditions are governing for the design and final lay-out. This
is because the fabrication, erection and load out methodology can be varied to suit the
structure, but the other load cases are fundamental in the structure design. Analyses were
therefore carried out for three primary load conditions, inplace, lift and transportation.
A brief discussion of the various load effects on the topside structure will be given in the
present chapter. Finally, the Ultimate limit state check for all conditions will be illustrated. All
loads that may influence the dimensioning are to be considered in the design analysis. Linear
elastic design techniques have been applied almost exclusively to design structural steel work
in offshore topside modules.

13

Structural analysis shall include all design conditions that required to cover the design limit
states as specified by the PSA Ref.[1], and NORSOK N-001 Ref.[9]. Actions shall be
combined in accordance with NORSOK N-003.
The combinations applied in the analysis are presented in Table 5-1below. Wave and current
are not applicable for this module.
Ice only to be combined with 10-1 wind and due to the small loads it is considered negligible.
Snow loads are assumed to have minimal effect on this, and are therefore considered
negligible
Limit states

Wind
Wave
100
100
ULS
100
100
SLS
ALS
Table 5-1 Environmental action combinations

Ice
-

Snow
-

Earthquake
100
10000

ALS 10 000-year wind is not governing due to reduced load- and material factors, and for
these analyses, it will be neglected.
The action factors to be used for the various limit states are presented in Table 5-2 below.
Load combination
ULS-a
ULS-b
SLS
ALS
Table 5-2 Action factors

P
1.3
1.0
1.0
1.0

L
1.3
1.0
1.0
1.0

E
0.7
1.3
1.0
-

D
1.0
1.0
-

A
1.0

Where:
P = Permanent loads
L = Variable functional loads (Live loads)
E = Environmental loads
D = Deformation loads
A = Accidental loads

14

5.1

INPLACE CONDITION

Inplace load combinations shall consider ULS a/b load conditions with contribution from
relevant load types as defined in chapter 4. Load combinations are established to give
maximum footing reactions at the interface between the modules and the Main Support Frame
(MSF).
Environmental loads wind, earthquake and barge accelerations shall be considered acting
from eight different directions at 45 degrees interval covering the complete rosette.
However, the wind load applied on inplace storm condition is considered East/West only.
Wind load from North and South directions are ignored because of shielding effects. The
module is analysed for wind with average recurrence period of 100 years.
The 100-year ice loads shall be combined with 10-year wind action. Considering the modules
height above water level, Ice load is neglected in the global analysis.
Snow loads shall not be combined with any other environmental loads. Considering the small
load magnitude of 0.5 KN/m2 it is concluded that the snow load can be neglected in the global
analyses.
Maximum deck beam deflections in the SLS condition shall be analysed combining all
permanent loads and variable functional loads. No other environmental loads will be included,
but horizontal displacements at selected spots on the weather deck are reported for 100-year
wind.
The super nodes applied for the boundary conditions for inplace condition are:
S(301005)
S(304005)
S(701005)
S(704005)
The support points for the inplace condition is to prevent constraint forces, a statically
determined support system (3-2-1-1) is applied on all dead loads.
Action combinations for inplace analysis are performed in Presel. Both Presel load
combinations comprise 3 levels, allowing combining and factoring loads up to a level for final
ULS/SLS/ALS load combination in SESAM Prepost
Basic load cases modeled in SESAM GeniE listed in Table 5-3, Table 5-4 Table 5-5, Table
5-6 and Table 5-7below

15

Load Case
1
2
3
20
21
22
23
24
25
26
27
31
32
33
34

Description
Self Generated Dead Weight
Secondary Steel
Outfitting Steel
Various Equipment
Electrical Dry Weight
Instrumental Dry Weight
Piping Dry Weight
HVAC
Safety Dry Weight
Surface Dry Weight
Architectural Dry weight
Personnel Load
Weight of gas and liquid in the pipe
Stored liquids and goods (Tanks)
Lay-down area

Direction
(-Z)
(-Z)
(-Z)
(-Z)
(-Z)
(-Z)
(-Z)
(-Z)
(-Z)
(-Z)
(-Z)
(-Z)
(-Z)
(-Z)
(-Z)

Table 5-3 Dead loads and live loads (-Z) direction

Load Case
101
102
103
120
121
122
123
124
125
126
127
131
132
133
134

Description
Self Generated Dead Weight
Secondary Steel
Outfitting Steel
Various Equipment
Electrical Dry Weight
Instrumental Dry Weight
Piping Dry Weight
HVAC
Safety Dry Weight
Surface Dry Weight
Architectural Dry weight
Personnel Load
Weight of gas and liquid in the pipe
Stored liquids and goods (Tanks)
Lay-down area

Direction
(+X)
(+X)
(+X)
(+X)
(+X)
(+X)
(+X)
(+X)
(+X)
(+X)
(+X)
(+X)
(+X)
(+X)
(+X)

Table 5-4 Dead and live loads (+X) direction

16

Load Case
201
202
203
220
221
222
223
224
225
226
227
231
232
233
234

Description
Self Generated Dead Weight
Secondary Steel
Outfitting Steel
Various Equipment
Electrical Dry Weight
Instrumental Dry Weight
Piping Dry Weight
HVAC
Safety Dry Weight
Surface Dry Weight
Architectural Dry weight
Personnel Load
Weight of gas and liquid in the pipe
Stored liquids and goods (Tanks)
Lay-down area

Direction
(+Y)
(+Y)
(+Y)
(+Y)
(+Y)
(+Y)
(+Y)
(+Y)
(+Y)
(+Y)
(+Y)
(+Y)
(+Y)
(+Y)
(+Y)

Table 5-5 Local Dead and live loads (+Y) direction

Load Case Description
50
Wind load from west
51
Wind load from East
Table 5-6 Wind loads

Direction
(+X)
(-X)

Load case
Description
101
Earthquake 10-2
102
Earthquake 10-2
103
Earthquake 10-2
201
Earthquake 10-4
202
Earthquake 10-4
203
Earthquake 10-4
Table 5-7 Earthquake loads

Direction
(-Z)
(+X)
(+Y)
(-Z)
(+X)
(+Y)

Model geometry, load geometry and load footprint are presented on Figure 5:1, 5:2 and 5:3
respectively and detail model geometry for inplace operational state is presented in
Appendix:-A

17

Figure 5-1 Numerical model of the module

Figure 5-2 Numerical model of the load

Figure 5-3 Numerical model of load and footprints

18

ULS DESIGN CHECK

The objective of structural analysis is to determine load effects on the structure such as
displacement, deformation, stress and other structural responses. These load effects define the
sizing of structural components and are used for checking resistance strength of these
components comply with limit state criteria defined by design rules and codes.
The structural analysis of the module for inplace condition is based on the linear elastic
behavior of the structure. As mentioned earlier the module is exposed to different loads. The
structural weight and permanent loads are considered as time-independent loads. Further, the
environmental loads are considered as time-dependent loads. Different wind durations are
calculated and 3seconed wind gust is selected and applied to compute the static wind load for
100 year return period.
These analyses are performed and results presented for each condition and. The Framework
member check for inplace conditions shows that except MY302030 all members of the
structure have utilization factor less than one for the applied loads in inplace operational
condition. This means that the members have sufficient capacity to withstand the applied
loads.
MY302030 fails the initial code check in Framework. However, the beam is reassessed and
found to be have sufficient capacity. Refer to Appendix E for further details
Yield, stability and deflection checks are performed as applicable for the relevant design
conditions according to criteria given in Section 2.3. Framework results for members with
utilization factor greater than 0.80 are presented in Table 5-8 below.
Member
MY302020
MY702020
MY301020
MY701020
MY702020
MY302010

Load case
Outcome
Utility Factor
543
Failure StaL
1.024
543
StaL
0.994
545
StaL
0.934
546
StaL
0.925
543
StaL
0.885
543
StaL
0.883
Table 5-8 Utilization factor inplace condition

Reassessment
0.61
-

The maximum displacements of the topside structure result from Xtract shows that the
structural deformation for worst load combinations is within the criteria, Maxdeformation <L/250.
SLS DESIGN CHECK
The objective of this analysis is to satisfy the serviceability limit criteria of the topside
structure and to make sure that the structure remains functional for its intended use.
The topside structure has sufficient capacity under ULS design check and the analysis is
conservative. This result indicates that the structure has sufficient capacity under service limit
state too. Because the SLS criteria states that the load and material factors is 1.0 for dead and
live load and no environmental load will be included. Therefore the SLS criteria are satisfied
during normal use.

19

5.2 LIFTING CONDITION

The purpose of lifting analysis is to ensure that lifting operation offshore shall be performed
in safe manner and in accordance with the regulations in force.
In preparation of offshore lifting analysis structure the following questions play a role:

Which weather condition?

What type of lifting?
What is the best approach?

These questions need to be considered carefully analysis at an early stage of the project. Good
communication between the engineers and operational people is a key factor for success.
Heavy lifting offshore is a very important aspect in a project, and needs attention from start
and throughout the project. Weather windows, i.e. periods of suitable weather conditions, are
required for this operation. Lifting of heavy loads offshore requires use of specialized crane
vessels.
The selected lifting method will impact the design consideration. There are several lifting
methods such as single hook, multiple hooks, spreader bar, no spreader, lifting frame, three
part sling arrangement, four part sling arrangement etc.
Lifting arrangement with spreader bar primarily is used to minimize the axial compression
force on members between the lifting points. In this master thesis the lifting arrangement used
is steel wire with four-sling arrangement which is directly hooked on to a single hook on the
crane vessel as shown in Figure 5:4 and Figure 5-5. The thickest sling currently available now
has a diameter of approximately 500 mm.
For lift condition USL-a is the governing load combination. Additional load factors such as
CoG factor, Dynamic amplification factor, Skew load factor, Design factor and Center of
Gravity envelop factor must be calculated and applied to get the total lifting weight. The
calculation of center of gravity is performed and presented in Appendix D.

Figure 5-4 Numerical model of sling

20

Figure 5-5 Numerical model of lifting

Lifting Design Load Factors
Load factors relevant for lifting design are summarized and presented as follows:
Dynamic Amplification Factor (DAF)
Offshore lifting is exposed to significant dynamic effects that shall be taken into account by
applying an appropriate dynamic amplification factor According to DNV .Ref. [21] resulting
DAF comes to 1.30for this module.
Skew Load Factor (SKL)
Skew loads are additional loads from redistribution due to equipment and fabrication
tolerances and other uncertainties with respect to force distribution in the rigging
arrangement.
Single crane four point lift without spreader bar the skew load factor can be taken 1.25
Design Factor (DF)

Design load factor DF defined as: DF = F * C

Where

= load factor
=consequence factor
F

Center of Gravity envelope factor (WCOG)

Center of Gravity envelope factor is calculated according Aker solutions working instruction
and presented in appendix D.

21

ULS DESIGN CHECK

As mentioned before the purpose of lifting analysis is to ensure that the lifting operation
offshore shall be performed in safe manner and in accordance with rules and regulations.
During preparation of lifting design analysis, weather window and lifting arrangement with
best approach had to be decided. Global design analysis of the critical members of the topside
module as shown in Figure 5-6
The members are categorized in three groups.
Single critical members, these are members connected to the lifting point and are assigned a
consequence factor of 1.30.
Reduced critical members, these are main members nor connected to the lifting points, and
assigned factor of 1.15.
None critical members, these are members considered to have no impact on the lifting
operation, and are assigned a consequence factor of 1.00
Figure 5-6 depicts the single critical members on the structure. The load factors are applied as
appropriate in Table 5-9 below.
Description
Load factor
Weight inaccuracy factor
1.03
Center of gravity inaccuracy factor
1.02
CoG factor
1.10
Skew load factor
1.25
Dynamic amplification factor
1.30
ULS-a load factor
1.30
Consequence factor Lift member
1.30
Lift member reduced consequence
1.15
Non-lift members No consequence
1.00
Table 5-9 Load factors applicable for lifting operation
The super nodes applied for the boundary conditions for lift condition are:
S(301040)
S(304040)
S(701040)
S(704040)
The tip of the hook is placed at (20m,10m,59m) in x-,y-and z-direction respectively.

22

Figure 5-6 Members at lifting points

Global analysis of the topside structure are performed and presented. The Framework member
check results shows that critical members at lifting point and have sufficient capacity with
respect to structural design criteria.
MY302030 fails the initial code check in Framework. However, the beam is reassessed and
found to be have sufficient capacity. Refer to Appendix E for further details
Members failing the Framework code check are reassessed. Ref. Appendix E
Utilization factors larger than 0.80 are presented in Table 5-10 below. UFs > 0.40 for single
critical members are listed in Table 5-11

Member
MY302030
MY301030
MY501020
MY701030
MY702030
MY302040
MY301040
MY702040

Load case
Outcome
Utility Factor Reassessment
1
Lbck
1.014
0.62
1
Lbck
0.914
1
StaL
0.909
1
Lbck
0.887
1
Lbck
0.863
1
StaL
0.845
1
StaL
0.810
1
StaL
0.800
Table 5-10 Utilization factor lifting condition

Member
Load case
Outcome
Utility Factor
MX601040
2
StaL
0.676
MX301040
2
StaL
0.660
MX304040
2
StaL
0.611
MX604040
2
StaL
0.542
MX651030
2
AxLd
0.444
MD301040
2
AxLd
0.430
Table 5-11 Utilization factor lifting condition for critical members

23

5.3 TRANSPORT CONDITION

Transportation in open sea is a challenging phase in offshore projects. This phase need careful
planning analysis and solutions to achieve a safe transport.
Transporting can be done on a flattop barge or on the deck of the heavy lift vessel [HLV].
This thesis is based on a standard North Sea barge, 300ft x 90ft, for the transport phase.
However, if transported on a known vessel or a HLV, the barge acceleration could be reduced
considerably.
Barge accelerations
Barge accelerations are action loads which will be applied on the module in transportation
condition. The intention with barge acceleration calculation is to identify applicable
accelerations for the barge tow and to calculate the acceleration load that will be applied on
the structure. These acceleration loads will be calculated and applied according to Nobel
Denton, Guidelines for marine transportations Ref. [20]
Calculations of barge acceleration loads for transport on the deck of a North Sea barge are
based on the Noble Denton criteria; refer to section 7.9, Table 7-2 Default Motion Criteria.
Transport accelerations are calculated based on the parameters; L>76m and B>23 as shown in
Table 5-1 below, and assuming the most unfavourable position on deck. These parameters are
considered to be conservative.
The physical size of a barge is important with regards to the operational weather window
because this can give a possibility to change the position of the structure and vessel coordinate
system is presented shown in Figure 5-6 below.
Barge motions are loads that influence the structural stability and strength capacity. Refer to
Appendix E for calculation details of barge accelerations.
Vessel type

T
Full cycle period (all categories)

Single amplitude
Roll

Standard North Sea barge

10

Pitch

20
12.5
secs
Table 5-12 Applied Noble Denton Criteria

Heave
acceleration
0.2g

Weather window needs to be suitable during transportation. The module will be analysed for
wind with average recurrence period of 1 year in combination with barge accelerations. Both
wind and accelerations are applied I eight directions with 45o intervals, completing the entire
rosette as showed in Figure 5-8. Wind load cases and directions are presented in Table 5-13
below.
Load Case
52
53
54
55

Description
Wind load from west
Wind load from south
Wind load from East
Wind load from North
Table 5-13 Basic wind loads

Direction
(+X)
(+Y)
(-X)
(-Y)

24

Figure 5-7 Vessel coordinate system

Figure 5-8 Direction of wind load

The transportation and installation of the large topside modules offshore is unique. The
reserve capacity built in to the design provides additional safety in the critical components of
the structure. The support points for the transport condition is chosen as the same as for the
in-place. To prevent constraint forces, a statically determined support system (3-2-1-1) is
applied on all dead loads. The support points are same as for inplace analysis.
During transport the module will be subjected to wind and acceleration loads. The module
will have a (2-2-2-2) support system in the same supports as above. In addition, sea fastening
in each corner will restrain horizontal movements.
The boundary conditions applied during transportation is presented in Figure 5-9 below.

Figure 5-9 Boundary conditions for during transportation

25

ULS DESIGN CHECK

Several members failed the initial Framework code check. To overcome this it was necessary
to either change the profile or introduce some temporary transportation reinforcements.
During the process of optimization, the solution was a combination of both. These temporary
reinforcements are shown in Figure 5-10 and Figure 5-11 below and shall be removed after
installation.

Figure 5-10 Reinforcement members for transport condition

Figure 5-11 Reinforcement members for transport condition

26

After temporary reinforcement and upgrading some members still failed the initial code check
in Framework. However, the beams are reassessed and found to be having sufficient capacity.
Ref. Appendix E for details.
Members with UF > 0.90 are listed in Table 5-14
Member
MX601020
MX301020
MX304020
MD454020
MX604020
MC504010
MD304020
MD451020
MC501010
MC604010
MD301020

Load case
601
609
609
617
601
625
617
617
625
625
601
Table 5-14

Outcome
Utility Factor
Fail StaL
1.029
Fail StaL
1.029
Fail StaL
1.013
Fail StaL
0.997
StaL
0.994
StaL
0.985
StaL
0.968
StaL
0.967
StaL
0.955
StaL
0.941
StaL
0.911
Utilization factor transport condition

Reassessed
0.59
0.59
0.59
-

To achieve sufficient capacity to withstand the worst load cases during inplace, lift and
transport conditions, the following cross sections have been selected as shown Table 5-15
below.
.
Member
Description
Type
Height
Width
t-flange
t-web
[mm]
[mm]
[mm]
[mm]
B020216
Hot rolled
Box
200
200
16
16
B040420
Hot rolled
Box
400
400
20
20
B040430
Welded
Box
400
400
30
30
B040440
Welded
Box
400
400
40
40
B060640
Welded
Box
600
600
40
40
HE600B
Hot rolled
HEB
600
300
155
30
HE800B
Hot rolled
HEB
800
300
175
33
HE1000B
Hot rolled
HEB
1000
300
190
36
I08402035
Welded
I-girder
800
400
35
20
I1042035
Welded
I-girder
1000
400
35
20
I1242035
Welded
I-girder
1200
400
35
20
I1252035
Welded
I-girder
1200
500
35
20
SUPP
Support
850
850
60
60
dummy members

Table 5-15 Cross sections of the structure

27

DESIGN PADEYES

6.1 LOCAL ANALYSIS OF PADEYES

Padeyes are applied on lift attaching the sling for lifting operation. Several calculation methods
are available, but in this report Aker Solutions Working instruction for Padeye design and
strength assessment of padeyes is used.
The following stresses are evaluated and presented:

Pin hole stress

Main plate stress
Cheek plate stress
welds

Padeye plate structures are designed to sustain actions of the heaviest loaded lifting point. In
order to guarantee structural safety as well as economic design of padeyes, comprehensive
analysis should be performed.
Padeye body is usually welded to main structure. In some occasion main body may be welded
to a plate and bolted to main structure for easier removal. Stress check shall be done on body
and welded connection.
All loads are to be transferred from main structure to the padeye structures. The magnitude of
this load or force will be generated from framework analysis result and the padeye will be
designed according to relevant rules and design premises, Aker Solutions working instruction
for padeye design.
On preparation of designing the lifting padeye the following factors needs to be taken into
account:

Dynamic Amplification Factors

Skew load factor
CoG inaccuracy factor
Weight inaccuracy factor
Consequence factor

28

6.2 DESIGN CHECK OF PADEYES

The lifting slings must have sufficient length so that angle of the slings meets the criteria set.
To avoid transverse loading on the padeyes, these may be tilted to match the angles of slings.
The geometry of lifting pad eye is shown in
Figure 6-1below and the dimension of padeye hole will be calculated with respect to the
shackle dimension.
Shackle dimensions are taken from Green Pin shackle dimension data sheet Ref.[24] and
presented in Table 6-1.

Figure 6-1 Lifting padeye geometry

Pad eye are frequently applied for use of lifting point, and should be designed to match the
relevant standard shackle dimensions.

Figure 6-1 above depicts the different forces to be considered. In addition, a transverse load
equaling 3% of the sling load should be considered.
According to Aker solutions working instruction Ref. [19] the following criteria should fulfill
during design analysis of lifting padeyes.
Padeye hole diameter is calculated as
D=1.03d +2mm...Eq. (6:1)
The clearance between shackle bolt and pad eye hole should not exceed 4% of the shackle bolt
diameter
Pad eye plate thickness.
Total pad eye thickness T shall fulfill the following criterion: the padeye thickness at the hole
should not be less than 60% of the inside width of the joining shackle.

29

T > 0.6a ...... Eq. (6:2)

Where: - a is the shackle jaw
Increasing of clearance between the pin and the holes result in a decrease in the ultimate
capacity of the pad eye.
The clearance between the pad eye and the shackle jaw should be in the range of 2 to 4mm. a
set of spacer plate should be added if this cannot be achieved by the pad eye thickness with or
without cheek plates.
Pad eye radius
Pad eye radius(R) should be derived by addressing the tear out capacity. In addition, it is
checked towards shackle and sling geometry in terms of sufficient space.
Limits are described by the following formula: 1.3D< R <2d ... Eq. (6:3)
Where: - D = pad eye hole diameter
d = shackle bolt diameter
R = minimum radius from center of hole to pad eye edge.
Pad eye Height and Length
Pad eye height and length should be decided on the basis of a load distribution perspective and
an operational judgment.
Determination of pad eye geometry and formulas below shows methods to calculate pad eye
height and strength.
Load angle 135deg. > >45deg.
Where:
tc - cheek plate thickness
tp- pad eye plate thickness
R -minimum radius from center of hole to pad eye edge
D=1.03d`+2mm
1.3D < R< 2d`
R=r+tc ........................................................ Eq. (6:4)
Eq. (6:5)

Eq. (6:6)
Height (h) =2r............ Eq. (6:7)
Length (l) = 1.8h....................................... Eq. (6:8)
The detailed lifting padeye analysis is performed according to the rules and design premises.
The complete analysis and results are presented in Appendix F
The selected shackle has to house both pad eye and the selected sling. The selected shackle and
pin are presented in Figure 6-2 and Table 6-1.
WLL
[tons]

A
[mm]

B
[mm]

C
[mm]

D
[mm]

E
[mm]

F
[mm]

G
[mm]

H
[mm]

J
[mm]

L
[mm]

1500

280

290

640

225

360

460

450

1480

1010

1060

30

Table 6-1 Shackle and pin dimensions

Figure 6-2 Shackle geometry

31

7
7.1

DESIGN OF JOINTS
LOCAL ANALYSIS OF JOINTS

Local joint analysis is an important structural analysis to ensure structural integrity.

The mode of failure of a statically loaded joint depends on the type of joint, the loading
conditions and the joint geometrical parameters.
The procedure for stress checks of welded joints are given in documenting the relevant nodes.
The procedure is briefly repeated as follows;
In order to separate and get the proper view of utilization level in different phases, each
analysis condition is treated separately. The method could also be utilized further to combine
all analysis in SESAM, and just check the most critical condition for each node.
First, a yield check of each member ends was performed in Framework, in order to establish
the possible dimensioning load cases for each node. By this, the maximum number of load
combinations to check for is limited by the number of members connected to the node.
Then, joint reaction forces (in the global axis system) are extracted from FRAMEWORK for
the defined load combinations.
A screening was then performed based on a conservative combination of the maximum yield
UF for each member connected at each node, in order to find the most critical node. For nodes
indicated by the screening to be highly utilized, detail calculation was performed in order to
find more correct node UF. Different hot spot in the node were checked towards the Von Mises
criterion, utilizing the correct sign for stresses. In general, conservative combination of normal
and shear stresses are used, giving some conservatism. I.e. Joints that have UF less than 1.05
are acceptable.
Local stability check of stiffeners and web is not performed for the actual nodes. The nodes are
in general robustly stiffened, and local buckling is not considered relevant.
7.2 DESIGN CHECK OF JOINTS
All joints shall be checked for all critical load conditions. Care shall be taken to cover
eccentricities in incoming members if this is not included in the computer analysis. Any
additional moments shall be added to the member forces extracted from the existing analysis.
The following procedure is established to ease the selection of critical load combinations. Excel
spreadsheets will in general be used to process the analysis results and perform detailed node
checks. In order to reduce the required work, several analysis results may be combined by use
of SESAM Prepost prior to the local calculations.
Perform an ordinary Von Mises check at each member ends and by use of Framework
extract utilization ratios and corresponding load combination, sorted on nodes, and
import into Excel. The number of dimensioning load cases will then be less or equal the
number of incoming members for each node.
Joint reaction forces are extracted by use of Framework for all joints for identified
dimensioning load cases.

32

 Calculate stresses in critical sections in the node.

Calculate (multidirectional) equivalent stresses based on the Von Mises yield criterion
and compare with design criteria. For class 1 and 2 sections the stresses may be
calculated based on the plastic moment of inertia. It must then be verified that repeated
yielding does not lead to failure of joints.
Calculate the local stability usage factor, where considered relevant, based on the stress
calculation from the Von Mises yield check.
The general 3D Von Mises stress calculation formulas as given below is used in order to find
the equivalent stress:

..Eq. (7:1)
For simplicity reason, the indexing used for shear stresses deviates some from the normal
definition, as e.g. xy donates shear stress acting in the xy-plane.
A conservative combination of utilization factors may be done as screening, in order to identify
the most critical nodes. The screening results may also be used as an upper limit for the actual
node utilization. The screening may be done by picking the worst UF from transverse beams(xdirection, longitudinal beams(y-direction) and vertical beams (z-direction including inclined
braces), respectively, and by assuming the worst possible sign combination, the equivalent Von
Mises utilization can be calculated by the following expression;

Eq. (7:2)
Where:
UFmax UFmed UFmin, which indicates that the worst situation is found if the maximum
stress is of opposite sign than the two other components
It should be noted that the screening method described above, may not give a conservative
estimate of the node utilization if the incoming member connection are not full strength
connections or if large shear forces are to be transferred inside the node. Nevertheless, the
screening may be used as a basis for critical node selection also in such cases.
The local joint analyses are performed on selected nodes based o screening results all three
conditions are considered and assessed. The analysis is performed according to Aker solutions
working instructions for joints. Analyses of these selected joints are performed and the
calculation and results are presented on Appendix G

33

DISCUSSION

Optimization of the structural designed layout of a topside module with respect to structural
integrity, weight safety and strength capacity is the main task of this master thesis.
As mentioned in previous chapters, the structure is exposed for different types of loads. These
load actions have different effects on the structural behavior of the topside module. The
structural capacity of the module for inplace condition was one of the main issues. It took much
time to achieve optimized structural profiles with respect to intended inplace operation.
However, I learnt that optimizing of the structural profiles has to consider all phases such as
transport and lifting operation, in addition to the inplace operating phase.
To achieve the sufficient capacity and structural integrity, members are carefully selected based
on their strength capacity. Inplace condition is considered as the basis for these selections.
To facilitate transport and/or lifting temporary reinforcements may be used. The main reason
behind this this idea is that inplace operation phase represents a long lasting period. All
conditions need to be considered and the structure will be designed and analyzed with respect
to life, environmental and economic risk. After the analyses and optimizing structural members
for inplace condition, transportation condition is considered and analyzed.
During transport analysis the structure will be analyzed as is (inplace condition) with transport
load combinations and the structural capacity will be studied carefully using Framework
member check result and Xtract for stress and deformation result. These results indicate the
utilization factors, the stress concentrations and deformations of the structural members. This
will lead us to find which part of the structure are most utilized, stressed and deformed.
Studying these structural responses carefully and finding the best engineering solution, the
structure can be modified reinforced to achieve the intended and required results.
The optimized structure for inplace condition was analyzed with the transport load cases. The
result from Framework member check indicated that the structure had insufficient capacity to
withstand these load combinations. The solution was to introduce some temporary
reinforcements to facilitate the transport condition. All temporary reinforcements shall be
removed before operating phase commences.
The last step of the global structural analysis will be lift condition. Lifting will not take place if
there is wind and/or waves. No environmental loads are applicable for lifting analysis. Only
dead loads are included, multiplied by an appropriate factor.
The analysis results of Framework show that the critical member at lifting points have
sufficient capacity to withstand the subjected load during this operation. However, some
members failed the initial code check in SESAM Framework. These beams have been
reassessed and found ok.
Global structural analysis and optimization for inplace, lift and transport conditions are
performed according to rules, codes and design premises. The analysis results show that each
condition has its own influence on how the structural members behave. As we mentioned
earlier, structural members must have a sufficient capacity to withstand all worst load cases and
it must be designed for worst load cases and conditions.

34

Optimizing or upgrading the structural member section property to achieve sufficient capacity
during transport condition reduced the utilization factors of these members for the inplace
condition. However, oil companies are frequently evaluating extension of operational life and
modifications. The extra capacity gained can be considered as a reserve for future
modifications.
The modification of a structure might be necessary in future aspect. This concept indicates that
the reserve capacity of structural strength is an advantage.
In preparation of local lifting padeye analysis of offshore structure, the loads which will be
applied on the padeye structure needs to be evaluated carefully.
Small sling angles will results in undesirable axial loads on members between lifting points.
However, this problem can be reduced by increasing the sling length. This method will increase
the vertical load and reduce the axial compression load on the exposed structural members.
Using spreader bar is another option that can be implemented during lifting arrangement. This
method will eliminate the axial compression loads on the structural members between lifting
points.
Time is a limiting factor for this thesis, and the lifting arrangement selected is a four point
single hook arrangement.
Design and analysis of lifting padeye are performed and presented in appendix F.
However, time limitation the analysis performed on this master thesis considered only foursling wire that connected with lifting padeyes and local analyses lifting padeyes are performed
and presented in on Appendix F
Local joint analyses are performed on selected nodes based on screening results. The analyses
and detailed calculations are done in Excel, and presented in Appendix G.
The topside structure has sufficient capacity under ULS design check and the analysis is
conservative. This result indicates that the structure has sufficient capacity under service limit
state too. Because the SLS criteria states that the load and material factors is 1.0 for dead and
live load and no environmental load will be included. Therefore the SLS criteria are satisfied
during normal use.

35

CONCLUSIONS

Structural design is very interesting, creative and challenging segment in engineering.

Structures should be designed such a way that they can resist applied forces and do not exceed
certain deformations. Moreover, structures should be economical. The best design is to design a
structure that satisfies the stress and displacement constraints, and results in the least cost of
construction. Although there are many factors that may influence the construction cost, the first
and most obvious one is the amount of material used to build the structure. Therefore,
minimizing the weight of the structure is usually the main goal of structural optimization.
The primary concern of the structural design analysis and optimization of this master thesis was
to obtain a proper weighed structure that has sufficient capacity and strength, with respect to
transportation, installation and operation. Apart from that the design analysis and optimization
of this structure is to achieve a structure that has high safety with respect to life, environment
and economic risk.
In preparation of the structural analyses the basis for the geometry and member properties were
selected for operational phase. However, the topside structure will be exposed for different
conditions before it reaches to the operational state. Lift and transportation phases were studied
and detail analyses were performed. Offshore structures are exposed for different conditions
and it is vital that the structure have sufficient strength and integrity to withstand these loads
and phases.
Strength capacity of a structure can be achieved by different approaches. One approach can be
constructing temporary reinforcement for members to facilitate temporary conditions such as
transport and lifting.
The modeling, design analysis and optimization are performed based on elastic behavior of
structural members. This linear elastic analysis is applied to find the structural members that
have less and high interaction ratio (IR).
The global analysis results have been evaluated and the structure has sufficient integrity and
capacity for all construction phases.
The global analysis of the topside structure shows that the structure at operational phase has
sufficient capacity to withstand the load at operational state, and the utilization factor indicates
the structure has reserve capacity. Oil companies are frequently evaluating extension of
operational life, and/or modifications to enable further facilities and developments. The reserve
capacity of the structure can be used in future modification of the structure.
Finally the global design analyses for inplace, lift and transport phases are performed and
presented. The results imply that the designed structure has sufficient capacity to withstand all
construction phases with respect to design criteria.
Padeye plate structures are designed to sustain actions of the heaviest loaded lift point. In order
to guarantee structural safety as well as economic design of padeyes, comprehensive analysis is
performed analysis result shows that the lifting padeyes have a sufficient capacity to withstand
the loads during lifting operation with respect to design criteria.

36

Local joint analysis is an important analysis in order to guarantee structural safety,

comprehensive local design analyses of selected joints are performed for inplace and lift
conditions. The results show that one joint needs reinforcement. The rest of the selected joints
have sufficient capacity strength to withstand the subjected loads with respect to design criteria
and rules.
The structure must remain functional for its intended use and SLS design check shows that the
structure fit the serviceability requirements during normal use.
Further studying in some areas will be interesting in this master thesis. However, time
limitation and scope of the thesis is too comprehensive to be dealt with in this period.
Areas that could be of interest to look into are:
Design and analysis of other lifting arrangement that can reduce axial compression loads.
Calculating reserve plastic capacity of padeye.
Further Finite-element analysis of stress concentration in padeyes
Local analysis of joints for transport condition.

37

REFERENCES
[1]

PSA Regulations relating to health, environment and safety in the petroleum activities (The
framework regulations) and the associated guidelines, 19 December 2003

[2]

PSA Regulations relating to design and outfitting of facilities etc. in the petroleum activities
(The facilities regulations) and the associated guidelines, 17 December 2003

[3]

C007-C-N-SD-101 Structural Design Specification of Offshore Installations. Rev B, Aker

Engineering A.S, 27.06.1990

[4]

C007-C-N-SS-600 Design Premises Structural Steel Detail Engineering. Rev 8, Aker

Engineering A.S. 09.11.90

[5]

C007-C-N-RD-225 Seismic accelerations for module analysis

[6]

C007-C-N-SP-110 Structural Steel Materials, Plates, Rev. B, 27.04.1989

[7]

C007-C-N-SP-111 Structural Steel Materials, Rolled Sections, Rev. A, 17.08.1988

[8]

C007-C-N-SP-127 High Strength Structural Steel, Plates, Rev. A, 11.07.1989

[9]

NORSOK N-001, Structural design, rev. 7, June 2010

[10]

NORSOK N-003, Actions and action effects, rev. 2, September 2007

[11]

NORSOK N-004, Design of steel structures, rev. 2, October 2004

[12]

NORSOK M-101, Structural steel fabrication, rev. 4, December 2000

[13]

NORSOK M-120, Material data sheets for structural steel, rev. 5, November 2008

[14]

EN 1993-1-1 Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for
buildings

[15]

EN 1993-1-3 "Eurocode 3: Design of steel structures - Part 1-3: General rules

[16]

EN 1993-1-8 "Eurocode 3: Design of steel structures - Part 1-8: Design of joints

[17]

DNV-RP-C205 Environmental conditions and environmental loads, April 2007

[18]

C007-C-N-RD-161 Design Resume, D22.Rev.Aker Engineering A.S

[19]

Aker Solution working instruction A237-N01, rev.2, Lifting Design 26.08.2009

[20]

GL Noble Denton 0030/N Guidelines for Marine Transportations 31 March 2010

[21]

DNV Rules for Marine Operations, Lifting January 1996

[22]

Ultimate Load Analysis Of Marine Structures, Tore H.Sreide, 2nd edition 1985

[23]

Handbook of offshore Engineering, Subrata.K.Chakrabarti, Elsevier Ltd, 1st edition 2005

[24]

WWW.Greenpin.com

38

APPENDIXES
A. GEOMETRY ....................................................................................................................... 40
B. JOINTS ................................................................................................................................ 44
C. SECTION PROPERTIES .................................................................................................... 48
D. ACTIONS ............................................................................................................................ 53
Basic dead and live load ....................................................................................................... 54
Presel load combinations ...................................................................................................... 58
Prepost load combinations .................................................................................................... 67
Wind load calculation ........................................................................................................... 70
Barge motion acceleration .................................................................................................... 76
Center of Gravity check ........................................................................................................ 78
E. GLOBAL ANALYSIS ....................................................................................................... 79
Framework member check ................................................................................................... 80
Member Assessments ........................................................................................................... 94
F. DESIGN CHECK OF PADEYE.......................................................................................... 99
G. DESIGN CHECK OF JOINTS ......................................................................................... 104

39

A. GEOMETRY

Figure A- 1 Member names, main deck

Figure A- 2 Member names, lower mezzanine deck

40

Figure A- 3 Member names, upper mezzanine deck

Figure A- 4 Member names, weather deck

41

Figure A- 5 Member names North face

Figure A- 6 Member names South face

42

Figure A- 7 Member names East face

Figure A- 8 Member names West face

43

B. JOINTS

Figure B- 1 Joint names

Figure B- 2 Joint names

44

Figure B- 3 Joint names

Figure B- 4 Joint names

45

Figure B- 5 Joint names

Figure B- 6 .Joint names

46

Figure B- 7 Joint names

Figure B- 8 .Joint names

47

C. SECTION PROPERTIES

Figure C- 1 Sections of module

Figure C- 2 Sections on main deck

48

Figure C- 3 Sections on lower mezzanine deck

Figure C- 4 Sections on upper mezzanine deck

49

Figure C- 5 Sections on weather deck

Figure C- 6 Sections on North face

50

Figure C- 7 Sections on South face

Figure C- 8 Sections on East face

51

Figure C- 9 Sections on West face

52

D. ACTIONS
Basic dead and live load
Load cases and factor
Inplace condition
Lift condition
Transport condition
Load combination Presel
Inplace condition
Lift Condition
Transport condition
Load combination Prepost
Inplace condition
Transport condition
Wind Load Calculation
Barge acceleration
Center of Gravity check

53

BASIC DEAD LOAD WEIGHT SESTRA 100

WEIGHT REPORT
LC

Description

X
Y
TONNE

201 Self Generated Dead Weight

202 Secondary Steel
203 Outfitting Steel
220 Various Equipment
221 Electrical Dry Weight
222 Instrumental Dry Weight
223 Piping Dry Weight
224 HVAC
225 Safety Dry Weight
226 Surface Dry Weight
227 Architectural Dry weight

LC

kN

1 Self Generated Dead Weight

2 Secondary Steel
3 Outfitting Steel
20 Various Equipment
21 Electrical Dry Weight
22 Instrumental Dry Weight
23 Piping Dry Weight
24 HVAC
25 Safety Dry Weight
26 Surface Dry Weight
27 Architectural Dry weight
101 Self Generated Dead Weight
102 Secondary Steel
103 Outfitting Steel
120 Various Equipment
121 Electrical Dry Weight
122 Instrumental Dry Weight
123 Piping Dry Weight
124 HVAC
125 Safety Dry Weight
126 Surface Dry Weight
127 Architectural Dry weight

SESTRA 100
X

580.9
232.4
58.1
336.0
62.0
24.0
200.0
28.0
28.0
12.0
48.0
580.9
232.4
58.1
336.0
62.0
24.0
200.0
28.0
28.0
12.0
48.0

5 699.0
2 279.6
569.9
3 296.2
608.2
235.4
1 962.0
274.7
274.7
117.7
470.9
5 699.0
2 279.6
569.9
3 296.2
608.2
235.4
1 962.0
274.7
274.7
117.7
470.9

580.9
232.4
58.1
336.0
62.0
24.0
200.0
28.0
28.0
12.0
48.0

5 699.0
2 279.6
569.9
3 296.2
608.2
235.4
1 962.0
274.7
274.7
117.7
470.9

1
2
3
20
21
22
23
24
25
26
27

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

-5 699.0
-2 279.6
-569.9
-3 296.2
-608.0
-235.4
-1 962.0
-274.7
-274.7
-117.7
-470.9

101
102
103
120
121
122
123
124
125
126
127

5 699.0
2 279.6
569.9
3 296.2
608.0
235.4
1 962.0
274.7
274.7
117.7
470.9

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

201
202
203
220
221
222
223
224
225
226
227

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

5 699.0
2 279.6
569.9
3 296.2
608.0
235.4
1 962.0
274.7
274.7
117.7
470.9

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

Figure D-1 Basic Load case SESTRA 100

54

BASIC DEAD WEIGHT LOAD SESTRA 150

WEIGHT REPORT

SESTRA 150

Factor
Z Direction

Load CaseDescription
1 Self Generated Dead Weight
2 Secondary Steel
3 Outfitting Steel

20 Various Equipment
21 Electrical Dry Weight
22 Instrumental Dry Weight
23 Piping Dry Weight
24 HVAC
25 Safety Dry Weight
26 Surface Dry Weight
27 Architectural Dry weight

kN
1.1
1.1
1.1

1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1

kN
0.0
0.0
0.0

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

0.0 -6 268.9
0.0 -2 507.6
0.0 -626.9
-9 403.4

0.0

0.0 -9 403.3

0.0 -3 625.8
0.0 -668.8
0.0 -259.0
0.0 -2 158.2
0.0 -302.1
0.0 -302.1
0.0 -129.5
0.0 -518.0
-7 963.6

0.0

0.0 -7 963.5

X Direction
101 Self Generated Dead Weight
102 Secondary Steel
103 Outfitting Steel

120 Various Equipment

121 Electrical Dry Weight
122 Instrumental Dry Weight
123 Piping Dry Weight
124 HVAC
125 Safety Dry Weight
126 Surface Dry Weight
127 Architectural Dry weight

1.1
1.1
1.1

1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1

6 268.9
2 507.6
626.9
9 403.4

0.0
0.0
0.0

3 625.8
668.8
259.0
2 158.2
302.1
302.1
129.5
518.0
7 963.6

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

0.0
0.0
0.0
11 9 403.3

0.0

0.0

12 7 963.5

0.0

0.0

21

0.0 9 403.3

0.0

22

0.0 7 963.5

0.0

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

Y Direction
201 Self Generated Dead Weight
202 Secondary Steel
203 Outfitting Steel

220 Various Equipment

221 Electrical Dry Weight
222 Instrumental Dry Weight
223 Piping Dry Weight
224 HVAC
225 Safety Dry Weight
226 Surface Dry Weight
227 Architectural Dry weight

1.1
1.1
1.1

1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1

0.0 6 268.9
0.0 2 507.6
0.0
626.9
9 403.4

0.0
0.0
0.0

0.0 3 625.8
0.0
668.8
0.0
259.0
0.0 2 158.2
0.0
302.1
0.0
302.1
0.0
129.5
0.0
518.0
7 963.6

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

Figure D-2 Basic Load case SESTRA 150

55

BASIC DEAD WEIGHT LOAD SESTRA 200

WEIGHT REPORT
LC

DESCRIPTIONS

Factor

Z Direction

SESTRA 200
X

LC X

kN
1 Self Generated Dead Weight
2 Secondary Steel
3 Outfitting Steel
20 Various Equipment
21 Electrical Dry Weight
22 Instrumental Dry Weight
23 Piping Dry Weight
24 HVAC
25 Safety Dry Weight
26 Surface Dry Weight
27 Architectural Dry weight

1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

-6 268.9
-2 507.6
-626.9
-3 625.8
-668.8
-259.0
-2 158.2
-302.1
-302.1
-129.5
-518.0
-17 366.9

397

0.0

0.0 -17 367.0

X Direction
101 Self Generated Dead Weight
102 Secondary Steel
103 Outfitting Steel
120 Various Equipment
121 Electrical Dry Weight
122 Instrumental Dry Weight
123 Piping Dry Weight
124 HVAC
125 Safety Dry Weight
126 Surface Dry Weight
127 Architectural Dry weight

1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1

6 268.9
2 507.6
626.9
3 625.8
668.8
259.0
2 158.2
302.1
302.1
129.5
518.0
17 366.9

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0

6 268.9
2 507.6
626.9
3 625.8
668.8
259.0
2 158.2
302.1
302.1
129.5
518.0
17 366.9

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
398 17 367.0

0.0

0.0

0.0 17 367.0

0.0

Y Direction
201 Self Generated Dead Weight
202 Secondary Steel
203 Outfitting Steel
220 Various Equipment
221 Electrical Dry Weight
222 Instrumental Dry Weight
223 Piping Dry Weight
224 HVAC
225 Safety Dry Weight
226 Surface Dry Weight
227 Architectural Dry weight

1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1

0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
399

Figure D-3 Basic Load case SESTRA 200

56

BASIC LIVE LOADS SESTRA 100

WEIGHT REPORT
LC

Description

X
Y
TONNE

SESTRA 100
Z

kN

31 Persons Load
32 Weight of gas and liquid in the pipe
33 Stored liquid and goods
34 Layout Area

412.0
40.0
80.0
125.0

131 Persons Load

132 Weight of gas and liquid in the pipe
133 Stored liquid and goods
134 Layout Area

412.0
40.0
80.0
125.0

231 Persons Load

232 Weight of gas and liquid in the pipe
233 Stored liquid and goods
234 Layout Area

LC
kN
4 041.7
392.4
784.8
1 226.3

X
31
32
33
34

4 041.7
392.4
784.8
1 226.3

0.0
0.0
0.0
0.0

0.0 -4 041.7
0.0 -392.4
0.0 -784.8
0.0 -1 226.2

131 4 041.7
132
392.4
133
784.8
134 1 226.2

412.0
40.0
80.0
125.0

4 041.7
392.4
784.8
1 226.3

231
232
233
234

0.0
0.0
0.0
0.0

0.0
0.0
0.0
0.0

0.0 4 041.7
0.0
392.4
0.0
784.8
0.0 1 226.2

0.0
0.0
0.0
0.0

Figure D-4 Basic Load SESTRA 100

BASIC LIVE LOAD SESTRA 150

WEIGHT REPORT
LC

DESCRIPTIONS

SESTRA 150
X

kN

Z Direction
31 Persons Load
32 Weight of gas and liquid in the pipe
33 Stored liquides and goods (Tanks)
34 Laydown area

0.0
0.0
0.0
0.0

LC

0.0

0.0

-6 445.2

6 445.2

0.0

0.0

0.0

6 445.2

0.0

kN

0.0
0.0
0.0
0.0

4 041.7
392.4
784.8
1 226.3
6 445.2

X Direction
131 Persons Load
132 Weight of gas and liquid in the pipe
133 Stored liquides and goods (Tanks)
134 Laydown area

4 041.7
392.4
784.8
1 226.3
6 445.2

0.0
0.0
0.0
0.0

0.0
0.0
0.0
0.0

4 041.7
392.4
784.8
1 226.3
6 445.2

0.0
0.0
0.0
0.0

Y Direction
231 Persons Load
232 Weight of gas and liquid in the pipe
233 Stored liquides and goods (Tanks)
234 Laydown area

0.0
0.0
0.0
0.0

Figure D-5 Basic Live load SESTRA 150

57

Intermediate Level comb. SEL. 100

-z

+x

+y

1
2
3
20
21
22
23
24
25
26
27
101
102
103
120
121
122
123
124
125
126
127
201
202
203
220
221
222
223
224
225
226
227

Safety

Surface protection

Architectural

21
120
220

HVAC

20

Piping

Instrument

Equipment

2
101
201

Electrical

Outfitting steel

Secondary steel

-z
+x
+y

Self generated dead weight

Load-Name

BLC SEL. 10

INPLACE LOAD COMBINATIONS, PRESEL

22

23

24
123
223

25

26

27
126
226

1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0

Figure D-6 Presel load combination, static loads, run 1

Note. Static load cases are the same for Inplace and Transport conditions

58

Secondary steel

Outfitting steel

Equipment

Electrical

Instrument

Piping

HVAC

Safety

Surface protection

Architectural

3
103
203

20
120
220

21
121
221

22
122
222

23
123
223

24
124
224

25
125
225

26
126
226

27
127
227

1.1

1.1

1.1

2
11

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

12
21

1.1

1.1

22

Structural dead weights

Equipment dead load

Figure D-7 Presel load combination, static loads, run 2

-z

+x

11

12

+y

21

22

Load-Name

+y

2
102
202

BLC SEL. 150

+x

1
101
201

Intermediate Level
comb. SEL. 200

-z

Self generated dead weight

Load-Name

BLC SEL. 100

Intermediate Level
comb. SEL. 150

-z
+x
+y

-z

397

1.0

1.0

+x

398

1.0

1.0

+y

399

1.0

1.0

Figure D-8 Presel load combination, static loads, run 3

59

Intermediate Level comb. SEL. 100

-z

+x

+y

1
2
3
20
21
22
23
24
25
26
27
31
32
33
34
101
102
103
120
121
122
123
124
125
126
127
131
132
133
134
50
51
201
202
203
220
221
222
223
224
225
226
227
231
232
233
234

Wind from East

Persons load

Architectural

Wind from West

Stored liquides and goods

weight of gas and liquid

Surface protection

Safety

HVAC

Piping

Instrument

51

Electrical

50

Equipment

2
3
20 21 22 23 24 25 26 27 31 32 33 34
102 103 120 121 122 123 124 125 126 127 131 132 133 134
202 203 220 221 222 223 224 225 226 227 231 232 233 234

Outfitting steel

Laydown area

1
2
3

Secondary steel

Self generated dead weight

Load-name

BLC SEL. 10
-z
+x
+y

1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0

Figure D-9 Presel load combination, live loads, run 1

60

-z

1.1

1.1

1.1

1.1

1.1

1.1

Stored liquides and goods

weight of gas and liquid

Surface protection

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

Laydown area

Persons load

Architectural

Safety

HVAC

Piping

Electrical

Instrument

Wind from East

1.1

Equipment

Wind from West

1.1

Outfitting steel

51

Secondary steel

1
2
3 20 21 22 23 24 25 26 27 31 32 33 34
101 102 103 120 121 122 123 124 125 126 127 131 132 133 134 50
201 202 203 220 221 222 223 224 225 226 227 231 232 233 234
1.1

31
2

+x

Self generated dead weight

Load-name

BLC SEL. 100

1.0

1.0

1.0

1.0

1.0

1.0

1.0

1.0

1.1

32

1.0

50

1.0

51
3

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1
1.0

33

1.0

1.0

1.0

-z

+x

+y

101
31
201
102
202
32
150
151
103
203
33

31
32
33

0.020

Wind from East

1
2
3

Wind from West

Live

Load-Name

-z
+x
+y

Dead

Figure D-10 Presel load combination, live loads, run 2

BLC SEL. 150

+y

Intermediate Level comb. SEL. 197

Intermediate Level comb.

SEL. 150

-z
+x
+y

50

51

0.020
1.000

0.061

0.061

0.051
0.245

0.245
0.510
1.000
1.000

0.051
0.255

0.255
0.510

Figure D-11 Presel load combination, live loads, run 3

61

Intermediate Level
comb. SEL. 150

-z
1

Secondary steel
Outfitting steel
Equipment
Electrical
Instrument
Piping
HVAC
Safety
Surface protection
Architectural

1
2
3
20
21
22
23
24
25
26
27

Self generated dead weight

-z

Load-Name

BLC SEL. 100

Intermediate Level comb.

SEL. 100

Self generated dead weight

Secondary steel
Outfitting steel
Equipment
Electrical
Instrument
Piping
HVAC
Safety
Surface protection
Architectural

Load-Name

Direction

BLC SEL. 11

LIFTING LOAD COMBINATIONS, PRESEL

1
2
3
20
21
22
23
24
25
26
27

1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0

Figure D-12 Presel load combination, static loads, run 1

1
2
3
20
21
22
23
24
25
26
27

1.1
1.1
1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

1.1

Figure D-13 Presel load combination, static loads, run 2

62

Structural dead weights

Equipment dead load

Load-Name

Direction

BLC SEL. 150

Dead load

Load-Name

Direction

BLC SEL. 200

Intermediate Level comb.

-z
397
1.0
1.0
SEL. 200
Figure D-14 Presel load combination, static loads, run 3

397
-z
1
2.808
-z
2
3.174
Figure D-15 Presel load combination, static loads, run 4
Top Level comb. SEL. 201

63

Intermediate Level comb. SEL. 100

-z

+x

+y

1
2
3
20
21
22
23
24
25
26
27
31
32
33
34
101
102
103
120
121
122
123
124
125
126
127
131
132
133
134
52
53
54
55
201
202
203
220
221
222
223
224
225
226
227
231
232
233
234

Wind from South

Wind from North

Persons load

Architectural

Wind from East

Stored liquides and goods

weight of gas and liquid

Surface protection

Safety

HVAC

Piping

55

Instrument

54

Electrical

53

Equipment

52

Outfitting steel

2
3
20 21 22 23 24 25 26 27 31 32 33 34
102 103 120 121 122 123 124 125 126 127 131 132 133 134
202 203 220 221 222 223 224 225 226 227 231 232 233 234

Secondary steel

Wind from West

1
2
3

Laydown area

-z
+x
+y

Self generated dead weight

Load-name

BLC SEL. 10

TRANSPORT LOAD COMBINATION, PRESEL

1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0

Figure D-16 Presel load combination, live loads, run 1

64

Electrical

Instrument

Piping

HVAC

Safety

Surface protection

Architectural

20
120
220

21
121
221

22
122
222

23
123
223

24
124
224

25
125
225

26
126
226

27
127
227

Wind from East

Equipment

3
103
203

Wind from East

Outfitting steel

2
102
202

Wind from East

Secondary steel

1
101
201

Wind from West

Self generated dead weight

Load-name

BLC SEL. 100

-z
+x
+y

52

53

54

55

1 1.100 1.100 1.100

Intermediate Level comb. SEL. 150

+y

1.100 1.100 1.100 1.100 1.100

1.100

1.100 1.100

101 0.200 0.200 0.200 0.200 0.200 0.200 0.200 0.200 0.200 0.200 0.200
104 -0.200 -0.200 -0.200 -0.200 -0.200 -0.200 -0.200 -0.200 -0.200 -0.200 -0.200
11 1.100 1.100 1.100

+x

1.100 1.100 1.100 1.100 1.100

12

1.100

1.100 1.100

102 1.054 1.054 1.054 1.054 1.054 1.054 1.054 1.054 1.054 1.054 1.054
152

1.000

153

0.707 0.707

154

1.000

155

0.707 0.707

156

1.000
0.707 0.707

157
1.000

158
0.71

159

0.707

21 1.100 1.100 1.100

+y

22

1.100 1.100 1.100 1.100 1.100

1.100

1.100 1.100

103 0.530 0.530 0.530 0.530 0.530 0.530 0.530 0.530 0.530 0.530 0.530

Figure D-17 Presel load combination, live loads, run 2

65

+x

+y

Wind

Wind

Wind

Wind

Wind

Wind

Wind

Wind

101

Barge acceleration

Barge acceleration

2
12
22

Barge acceleration

Equipment dead load

1
11
21

Barge acceleration

Self generated weight

Load-Name

BLC SEL. 150

Intermediate Level comb. SEL. 197

-z
+x
+y
-z

152

153

154

155

156

157

158

159

104
102
103

1 1.000 1.000
2 1.000 1.000
52
1.000
53
1.000
54
1.000
55
1.000
56
1.000
57
1.000
58
1.000
59
1.000
3 1.000 1.000
201
1.000
202
1.000
203
0.707 0.707
204
1.000
205
-0.707 0.707
206
-1.000
207
-0.707 -0.707
208
-1.000
209
0.707 -0.707
210
1.000

Figure D-18 Presel load combination, live loads, run 3

66

PREPOST LOAD COMBINATIONS, INPLACE

Wind load (+X)

Wind load (-X)

Earthquake load 10^-2 (Z)

Earthquake load 10^-2 (X)

Earthquake load 10^-2 (Y)

Earthquake load 10^-4 (Z)

Earthquake load 10^-4 (X)

Earthquake load 10^-4 (Y)

103

201

202

203

1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0

1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0

1.3

ULS b

503
504
522
524
526
528
530
532
541
542
543
544
545
546

1.0
1.0
1.0
1.0
1.0
1.0

1.0
1.0
1.0
1.0
1.0
1.0

Live Load (-Z)

102

Dead Load (-Z)

101

LOAD CASE

150
0.7

ULS a

31
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3

151

501
502
521
523
525
527
529
531

397
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3

ALS

LOAD COMBINATIONS

0.7
1.3
1.3
1.3
1.3
0.7 0.495 0.495
0.7 -0.495 0.495
0.7 -0.495 -0.495
0.7 0.495 -0.495

1.3
1.3
1.3
1.3
1.3
1.3 0.919 0.919
1.3 0.919 0.919
1.3 -0.919 -0.919
1.3 0.919 -0.919
1.0
1.0
1.0 0.707 0.707
1.0
1.0
1.0 -0.707 0.707
1.0 -0.707 -0.707
1.0 0.707 -0.707

Figure D-19 Prepost load combination, inplace

67

LOAD COMBINATION

Load Name

Dead Load (-Z)

LOAD COMBINATIONS

ULS a

1
2

397
2.808
3.174

Figure D-20 Load combination lift

68

PREPOST LOAD COMBINATIONS, TRANSPORT

201 202 203 204 205 206 207 208 209

1.3 1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3

602
604
606
608
610
612
614
616
618
620
622
624
626
628
630
532

1.0 1.3
1.0
1.3
1.0
1.3
1.0
1.3
1.0
1.3
1.0
1.3
1.0
1.3
1.0
1.3
1.0 1.3
1.0
1.3
1.0
1.3
1.0
1.3
1.0
1.3
1.0
1.3
1.0
1.3
1.0
1.3

1.0 1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0

Barge acceleration (-Z)

Barge acceleration (+X-Y)

Barge acceleration (-X-Y)

Barge acceleration (-X)

Barge acceleration (-X+Y)

Barge acceleration (+Y)

Barge acceleration (+X+Y)

Barge acceleration (+X)

Barge acceleration (-Z)

Wind load (+X-Y)

Wind load (-Y)

Wind load (-X-Y)

Wind load (-X)

Wind load (-X+Y)

Wind load (+Y)

Wind load (-X+Y)

Dead Load (-Z)

397 52 53 54 55 56 57 58 59
1.3 0.7
1.3
0.7
1.3
0.7
1.3
0.7
1.3
0.7
1.3
0.7
1.3
0.7
1.3
0.7
1.3 0.7
1.3
0.7
1.3
0.7
1.3
0.7
1.3
0.7
1.3
0.7
1.3
0.7
1.3
0.7

Live Load (-Z)

LOAD CASE

ULS a

601
603
605
607
609
611
613
615
617
619
621
623
625
627
629
631

ULS b

Wind load (+X)

LOAD COMBINATIONS

210

1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3

1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0

Figure D-21 Prepost load combination, transport

69

WIND LOAD CALCULATION

70

71

72

73

74

75

BARGE ACCELERATION

76

77

COG ENVELOPE
Input SESTRA listing
LOADCASE

X-LOAD

Y-LOAD

1.46E-17
1.73E+01
0.00E+00

397
398
399

Z-LOAD

-1.19E-18
0.00E+00
1.73E+01

X-MOM

-1.73E+01
1.66E-10
-2.30E-08

Y-MOM

2.52E-01
-1.01E-03
-3.31E-01

Z-MOM

0.00E+00
-1.81E-04
1.26E-22

X-RMOM

0.00E+00
3.89E-01
-5.96E-19

Y-RMOM

-1.74E+02
5.19E-10
-1.61E+02

Z-RMOM

3.46E+02 -1.69E-16
1.61E+02 -1.74E+02
4.32E-07 3.45E+02

Figure D-22 SESTRA output

CoG check
FROM SESTRA LISTING

X-LOAD
AccelerationLoadCase
-Z
397

[KiloNewton]
Y-LOAD Z-LOAD

0.0

0.0

17,300.0

[MegaNewton*Meter]
X-RMOM Y-RMOM Z-RMOM
174.0

346.0

0.0

CoG (Local Coord.)

Y
Z

20.001

398

17,300.0

0.0

0.0

0.0

160.7

174.0

399

0.0

17,300.0

0.0

160.7

0.0

345.1

19.947

20.000
20.000
19.974

20.000
10.000
10.060

10.000
9.288

x
0.026

y
0.060

Weight
Length between support points
Geometric middle
CoG, "as is" analysis

1,603.2

3451.8

10.060
10.060

1763.5
9.288

1763.5

9.288

1763.5

CoG shift = ((Lx+x)/Lx)*((Ly+y)/Ly)

Original weight report

Weight (T)

1.0043
299.290

155.460

525.210

From GeniE

Check
Weight
[ton]

Load
[kN]

LC397

Self generated weight

1,763.51

1,763.5

LC398

Self generated weight

1,763.51

1,763.5

LC399

Self generated weight

1,763.51

1,763.5

x-cog
[m]
20.001

y-cog
[m]

z-cog
[m]

10.060
10.060

19.947

x-cog

y-cog

OK

OK

OK

9.288

OK

9.288

OK

OK

0.800 %

0.500 %

Max diff:
As of:

Load

OK

z-cog

OK
OK

0.500 %

0.500 %

5/31/2012

Figure D-23 CoG calculation

78

E. GLOBAL ANALYSIS
FRAMEWORK MEMBER CHECK RESULT
Inplace condition
Lift condition
Transport condition
MEMBER ASSESMENT
Inplace condition
Lift condition
Transport condition

79

FRAMEWORK MEMBER CHECK RESULT, INPLACE

******
********
**
**
**
*******
*******
**
**
**
********
******

******
********
**
**
**
**
**********
*********
**
**
**
********
******

******
********
**
**
**
*******
*******
**
**
**
********
******

******
********
**
**
**
*********
**********
**
**
**
**
*********
****** **

** *** ****
*************
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**

*********************************************************************************************
*********************************************************************************************
**
**
**
**
**
******* ******
*****
*
* ******* *
*
*****
******
*
*
**
**
*
*
* *
* **
** *
*
* *
* *
* *
*
**
**
*
*
* *
* * * * * *
*
* *
* *
* * *
**
**
*****
******
******* * * * *****
* * * *
* ******
***
**
**
*
*
*
*
* *
* *
* * * *
* *
*
* *
**
**
*
*
*
*
* *
* *
* * * *
* *
*
*
*
**
**
*
*
* *
* *
* *******
** **
*****
*
* *
*
**
**
**
**
**
**
Postprocessing of Frame Structures
**
**
**
**
**
*********************************************************************************************
*********************************************************************************************
Marketing and Support by DNV Software

Program id
Release date
Access time
User id

: 3.6-02
: 7-JUN-2011
: 12-JUN-2012 09:17:05
: 123333

DATE: 12-JUN-2012 TIME: 09:17:05

1

PROGRAM: SESAM

Computer
Impl. update
Operating system
CPU id
Installation
FRAMEWORK 3.6-02

7-JUN-2011

MEMBER check: EC3/NS3472 ENV 1993-1-1/Ed 3

Run:
Superelement:
Loadset:
ULS
T197
INPLACE
Priority....: Worst Loadcase
Usage factor: Above
0.50

:
:
:
:
:

586
Win NT 6.1 [7601]
0476028815
, EURW120334
PAGE:

SUB PAGE:

NOMENCLATURE:
Member
LoadCase
CND
Type
Joint/Po
Outcome
UsfTot
UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
Phase
SctNam
EleNum
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z
Class w,f

Name of member
Name of loadcase
Operational, storm or earthquake condition
Section type
Joint name or position within the member
Outcome message from the code check
Total usage factor: UsfTot = UsfAx + UsfMy + UsfMz
Usage factor due to axial stress
Acting axial force
Axial (buckling) force capacity about y-axis
Design bending moment used for bending about y-axis
Moment capacity for bending about y-axis
Effective length factor for bending about y-axis
Buckling length for bending about y-axis
Phase angle in degrees
Section name
Element number
Usage factor due to bending about y-axis
Yield strength
Axial (buckling) force capacity about z-axis
Design bending moment used for bending about z-axis
Moment capacity for bending about z-axis
Effective length factor for bending about z-axis
Buckling length for bending about z-axis
Usage factor due to bending about z-axis
Material factor, gamma-M1
Equivalent stress used in von Mises stress check
Length between lateral support of compression flange
Lateral buckling factor
Buckling curve for bending about y,z-axes
Cross section class for web, flange

80

Member

LoadCase CND Type

Phase
SctNam

Joint/Po Outcome
EleNum

UsfTot

UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z Class w,f
---------------------------------------------------------------------------------------------------------------------------MY302020 543
I
0.50
*Fa StaL
1.024
0.027 -1.35E-01 1.76E+01 -3.22E+00 3.23E+00
1.000
1.00E+01
I1242035 229
0.997 4.20E+02 4.97E+00 9.71E-05 1.06E+00
1.000
1.00E+01
0.000
1.150
0.00E+00 1.00E+01
1.000
C , C
2 , 1
MY702020 543

I
0.50
I1242035 371

StaL

0.994

0.027 -1.36E-01
0.965 4.20E+02
0.001
1.150

1.76E+01 -3.12E+00
4.97E+00 -1.02E-03
0.00E+00 1.00E+01

3.23E+00
1.06E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 1

MY301020 545

I
0.50
I1242035 221

StaL

0.934

0.018 -8.77E-02
0.902 4.20E+02
0.014
1.150

1.76E+01 -2.91E+00
4.97E+00 1.53E-02
0.00E+00 1.00E+01

3.23E+00
1.06E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 1

MY701020 546

I
0.50
I1242035 363

StaL

0.925

0.015 -7.39E-02
0.889 4.20E+02
0.021
1.150

1.76E+01 -2.87E+00
4.97E+00 -2.27E-02
0.00E+00 1.00E+01

3.23E+00
1.06E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 1

MY702010 543

I
0.50
I1252035 369

StaL

0.885

0.073 -6.23E-01
0.808 4.20E+02
0.003
1.150

2.01E+01 -3.84E+00
8.50E+00 -3.34E-03
0.00E+00 1.00E+01

4.75E+00
1.07E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
3 , 2

MY302010 543

I
0.50
I1252035 227

StaL

0.883

0.078 -6.63E-01
0.804 4.20E+02
0.001
1.150

2.01E+01 -3.82E+00
8.50E+00 1.20E-03
0.00E+00 1.00E+01

4.75E+00
1.07E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
3 , 2

MY301010 545

I
0.50
I1252035 219

StaL

0.782

0.061 -5.19E-01
0.671 4.20E+02
0.050
1.150

2.01E+01 -3.19E+00
8.50E+00 5.32E-02
0.00E+00 1.00E+01

4.75E+00
1.07E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
3 , 2

MY701010 546

I
0.50
I1252035 361

StaL

0.779

0.057 -4.85E-01
0.674 4.20E+02
0.048
1.150

2.01E+01 -3.20E+00
8.50E+00 -5.14E-02
0.00E+00 1.00E+01

4.75E+00
1.07E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
3 , 2

MZ304010 544

BOX
B060640

0.50
234

Stab

0.665

0.274 -7.98E+00
0.316 4.20E+02
0.074
1.150

2.91E+01 -2.18E+00
2.91E+01 5.11E-01
0.00E+00 6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MY302030 527

I
0.50
I0852035 231

Lbck

0.661

0.000
0.659
0.002

1.81E+01 2.23E+00
1.81E+01 -3.50E-03
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MF104010 543

BOX
B040420

0.50
160

Stab

0.660

0.333 -2.39E+00
0.255 3.55E+02
0.072
1.150

7.20E+00
7.20E+00
0.00E+00

3.41E-01
9.70E-02
7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MF902520 543

BOX
B040420

0.50
450

Stab

0.660

0.272 -1.96E+00
0.343 3.55E+02
0.045
1.150

7.20E+00
7.20E+00
0.00E+00

4.59E-01
5.97E-02
7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MY302040 529

I
0.50
I0852035 232

StaL

0.640

0.031 -2.50E-01
0.602 4.20E+02
0.007
1.150

1.61E+01 -2.04E+00
8.09E+00 1.11E-02
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MZ301010 545

BOX
B060640

0.50
216

Stab

0.637

0.253 -7.36E+00
0.311 4.20E+02
0.072
1.150

2.91E+01
2.91E+01
0.00E+00

2.14E+00
4.99E-01
6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MY701030 531

I
0.33
I0852035 365

StaL

0.624

0.001 -5.37E-03
0.623 4.20E+02
0.000
1.150

1.61E+01 -2.11E+00
8.09E+00 -5.68E-04
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MX204010 542

I
0.50
I1242035 208

StaL

0.618

0.141 -1.68E+00
0.446 4.20E+02
0.030
1.150

1.85E+01 -2.43E+00
1.19E+01 2.05E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MY702030 525

I
0.50
I0852035 373

Lbck

0.613

0.000
0.612
0.001

1.21E-03
4.20E+02
1.150

1.81E+01 2.07E+00
1.81E+01 -2.13E-03
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MZ704010 542

BOX
B060640

0.50
376

Stab

0.612

0.228 -6.64E+00
0.304 4.20E+02
0.080
1.150

2.91E+01 -2.09E+00
2.91E+01 -5.48E-01
0.00E+00 6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MX201010 546

I
0.50
I1242035 200

StaL

0.610

0.138 -1.64E+00
0.439 4.20E+02
0.033
1.150

1.85E+01 -2.39E+00
1.19E+01 -2.25E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MZ701010 546

BOX
B060640

0.50
358

Stab

0.609

0.230 -6.70E+00
0.298 4.20E+02
0.081
1.150

2.91E+01 2.05E+00
2.91E+01 -5.57E-01
0.00E+00 6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MY301030 529

I
0.33
I0852035 223

Lbck

0.607

0.000
0.606
0.001

4.89E-02
4.20E+02
1.150

1.81E+01
1.81E+01
0.00E+00

2.05E+00
1.01E-03
1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY102040 545

I
HE800B

StaL

0.603

0.165 -3.45E-01
0.240 3.55E+02
0.197
1.150

9.04E+00
2.09E+00
0.00E+00

2.80E-01
9.39E-02
1.00E+01

1.17E+00
4.76E-01
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 1

0.50
158

1.24E-01
4.20E+02
1.150

81

4
Member

LoadCase CND Type

Phase
SctNam

Joint/Po Outcome
EleNum

UsfTot

UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z Class w,f
---------------------------------------------------------------------------------------------------------------------------ME101320 546
BOX
0.50
Stab
0.583
0.280 -2.01E+00 7.20E+00 2.89E-01 1.34E+00
1.000
7.49E+00
B040420 141
0.216 3.55E+02 7.20E+00 1.17E-01 1.34E+00
1.000
7.49E+00
0.088
1.150
0.00E+00 7.49E+00
0.000
C , C
1 , 1
MY301040 529

I
0.50
I0852035 226

StaL

0.576

0.013 -1.09E-01
0.560 4.20E+02
0.003
1.150

1.61E+01
8.09E+00
0.00E+00

1.89E+00
4.61E-03
1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MX604010 541

I
0.50
I1242035 350

StaL

0.569

0.087 -1.03E+00
0.452 4.20E+02
0.030
1.150

1.85E+01 -2.46E+00
1.19E+01 2.06E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX601010 541

I
0.50
I1242035 342

StaL

0.565

0.084 -9.99E-01
0.449 4.20E+02
0.032
1.150

1.85E+01 -2.44E+00
1.19E+01 2.22E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX704010 544

I
0.50
I1242035 391

StaL

0.564

0.125 -1.49E+00
0.405 4.20E+02
0.034
1.150

1.85E+01 -2.21E+00
1.19E+01 2.29E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX701010 545

I
0.50
I1242035 383

StaL

0.562

0.123 -1.47E+00
0.404 4.20E+02
0.035
1.150

1.85E+01 -2.20E+00
1.19E+01 -2.42E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

ME901010 545

BOX
B040420

0.50
432

Stab

0.561

0.204 -1.46E+00
0.291 3.55E+02
0.067
1.150

7.20E+00
7.20E+00
0.00E+00

3.89E-01
8.92E-02
7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MX602010 521

I
HE800B

0.50
345

StaL

0.560

0.028 -1.56E-01
0.532 3.55E+02
0.000
1.150

1.01E+01 -1.10E+00
5.62E+00 -6.02E-05
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

MY102010 501

I
HE800B

0.50
157

Lbck

0.557

0.000
0.488
0.068

4.56E-01
3.55E+02
1.150

1.01E+01 5.71E-01
1.01E+01 -3.26E-02
0.00E+00 1.00E+01

1.17E+00
4.76E-01
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 1

MY101010 501

I
HE800B

0.50
146

Lbck

0.552

0.000
0.484
0.068

4.83E-01
3.55E+02
1.150

1.01E+01 5.66E-01
1.01E+01 -3.24E-02
0.00E+00 1.00E+01

1.17E+00
4.76E-01
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 1

MY502020 527

I
0.50
I1252035 300

StaL

0.547

0.006 -4.85E-02
0.539 4.20E+02
0.002
1.150

2.01E+01
8.50E+00
0.00E+00

2.70E+00
3.50E-03
1.00E+01

5.01E+00
1.64E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 2

MX702010 525

I
HE800B

0.50
386

StaL

0.547

0.008 -4.35E-02
0.535 3.55E+02
0.004
1.150

1.01E+01 -1.11E+00
5.62E+00 1.88E-03
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

MY501020 529

I
0.50
I1252035 292

StaL

0.544

0.002 -1.80E-02
0.539 4.20E+02
0.002
1.150

2.01E+01
8.50E+00
0.00E+00

2.70E+00
3.69E-03
1.00E+01

5.01E+00
1.64E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 2

MZ504010 544

BOX
B040440

0.50
304

Stab

0.542

0.084 -1.33E+00
0.370 4.20E+02
0.089
1.150

1.60E+01 -1.05E+00
1.60E+01 -2.54E-01
0.00E+00 6.70E+00

2.85E+00
2.85E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MZ501010 545

BOX
B040440

0.50
287

Stab

0.536

0.081 -1.30E+00
0.367 4.20E+02
0.088
1.150

1.60E+01 1.05E+00
1.60E+01 -2.50E-01
0.00E+00 6.70E+00

2.85E+00
2.85E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MF102530 543

BOX
B040420

0.50
154

Stab

0.533

0.192 -1.39E+00
0.129 3.55E+02
0.211
1.150

7.25E+00
7.25E+00
0.00E+00

1.73E-01
2.83E-01
7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MX304010 544

I
0.50
I1242035 249

StaL

0.520

0.094 -1.12E+00
0.393 4.20E+02
0.033
1.150

1.85E+01 -2.14E+00
1.19E+01 2.25E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MY102020 543

I
HE800B

0.50
155

StaL

0.516

0.037 -1.47E-01
0.471 3.55E+02
0.009
1.150

9.74E+00 -7.94E-01
3.97E+00 4.11E-03
0.00E+00 6.65E+00

1.69E+00
4.76E-01
1.000

1.000
1.000
C , C

6.65E+00
6.65E+00
1 , 1

MX301010 545

I
0.50
I1242035 241

StaL

0.514

0.094 -1.12E+00
0.386 4.20E+02
0.033
1.150

1.85E+01 -2.10E+00
1.19E+01 -2.29E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX604020 541

I
HE800B

0.50
351

StaL

0.508

0.013 -7.34E-02
0.482 3.55E+02
0.013
1.150

1.01E+01 -9.95E-01
5.62E+00 6.22E-03
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

MX601020 541

I
HE800B

0.50
343

StaL

0.505

0.013 -7.19E-02
0.480 3.55E+02
0.012
1.150

1.01E+01 -9.93E-01
5.62E+00 -5.47E-03
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

MX302010 529

I
HE800B

0.50
244

StaL

0.502

0.029 -1.63E-01
0.472 3.55E+02
0.001
1.150

1.01E+01 -9.75E-01
5.62E+00 -7.00E-04
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

82

FRAMEWORK MEMBER CHECK LIFT MEMBERS

******
********
**
**
**
*******
*******
**
**
**
********
******

******
********
**
**
**
**
**********
*********
**
**
**
********
******

******
********
**
**
**
*******
*******
**
**
**
********
******

******
********
**
**
**
*********
**********
**
**
**
**
*********
****** **

** *** ****
*************
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**

*********************************************************************************************
*********************************************************************************************
**
**
**
**
**
******* ******
*****
*
* ******* *
*
*****
******
*
*
**
**
*
*
* *
* **
** *
*
* *
* *
* *
*
**
**
*
*
* *
* * * * * *
*
* *
* *
* * *
**
**
*****
******
******* * * * *****
* * * *
* ******
***
**
**
*
*
*
*
* *
* *
* * * *
* *
*
* *
**
**
*
*
*
*
* *
* *
* * * *
* *
*
*
*
**
**
*
*
* *
* *
* *******
** **
*****
*
* *
*
**
**
**
**
**
**
Postprocessing of Frame Structures
**
**
**
**
**
*********************************************************************************************
*********************************************************************************************
Marketing and Support by DNV Software

Program id
Release date
Access time
User id

: 3.6-02
: 7-JUN-2011
: 12-JUN-2012 09:22:13
: 123333

Computer
Impl. update
Operating system
CPU id
Installation

:
:
:
:
:

586
Win NT 6.1 [7601]
0476028815
, EURW120334

Copyright DET NORSKE VERITAS AS, P.O.Box 300, N-1322 Hovik, Norway
DATE: 12-JUN-2012 TIME: 09:22:13
1

PROGRAM: SESAM

FRAMEWORK 3.6-02

7-JUN-2011

MEMBER check: EC3/NS3472 ENV 1993-1-1/Ed 3

Run:
Superelement:
Loadset:
LIFT_1
T201
LIFT
Priority....: Worst Loadcase
Usage factor: Above
0.05

PAGE:

SUB PAGE:

NOMENCLATURE:
Member
Name of member
LoadCase
Name of loadcase
CND
Operational, storm or earthquake condition
Type
Section type
Joint/Po
Joint name or position within the member
Outcome
Outcome message from the code check
UsfTot
Total usage factor: UsfTot = UsfAx + UsfMy + UsfMz
UsfAx
Usage factor due to axial stress
N
Acting axial force
Ndy(Nkdy)
Axial (buckling) force capacity about y-axis
My*ky
Design bending moment used for bending about y-axis
Mdy
Moment capacity for bending about y-axis
Ky
Effective length factor for bending about y-axis
Ly
Buckling length for bending about y-axis
Phase
Phase angle in degrees
SctNam
Section name
EleNum
Element number
UsfMy
Usage factor due to bending about y-axis
Fy
Yield strength
Ndz(Nkdy)
Axial (buckling) force capacity about z-axis
Mz*kz
Design bending moment used for bending about z-axis
Mdz
Moment capacity for bending about z-axis
Kz
Effective length factor for bending about z-axis
Lz
Buckling length for bending about z-axis
UsfMz
Usage factor due to bending about z-axis
Gamma-m
Material factor, gamma-M1
vMises
Equivalent stress used in von Mises stress check
Lbuck
Length between lateral support of compression flange
C1
Lateral buckling factor
BCrv y,z
Buckling curve for bending about y,z-axes
Class w,f
Cross section class for web, flange
DATE: 12-JUN-2012 TIME: 09:22:13
PROGRAM: SESAM
FRAMEWORK 3.6-02
7-JUN-2011
MEMBER check: EC3/NS3472 ENV 1993-1-1/Ed 3
Run:
Superelement:
Loadset:
LIFT_1
T201
LIFT
Priority....: Worst Loadcase
Usage factor: Above
0.05

PAGE:

SUB PAGE:

83

Member

LoadCase CND Type

Phase
SctNam

Joint/Po Outcome
EleNum

UsfTot

UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z Class w,f
---------------------------------------------------------------------------------------------------------------------------MY302030 1
I
0.45
*Fa Lbck
1.014
0.000 8.07E-02 1.81E+01 3.43E+00 3.38E+00
1.000
1.00E+01
I0852035 3644
1.014 4.20E+02 1.81E+01 -4.54E-04 1.62E+00
1.000
1.00E+01
0.000
1.150
0.00E+00 1.00E+01
1.000
C , C
1 , 2
MY301030 1

I
0.45
I0852035 3601

Lbck

0.914

0.000
0.914
0.001

6.72E-02
4.20E+02
1.150

1.81E+01 3.09E+00
1.81E+01 -1.10E-03
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY501020 1

I
0.45
I1252035 3901

StaL

0.909

0.119 -1.01E+00
0.789 4.20E+02
0.000
1.150

2.01E+01 3.75E+00
8.50E+00 -5.78E-05
0.00E+00 1.00E+01

4.75E+00
1.07E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
3 , 2

MY701030 1

I
0.45
I0852035 4222

Lbck

0.887

0.000
0.887
0.000

9.11E-02
4.20E+02
1.150

1.81E+01
1.81E+01
0.00E+00

3.00E+00
5.44E-04
1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY702030 1

I
0.45
I0852035 4265

Lbck

0.863

0.000
0.862
0.000

1.08E-01
4.20E+02
1.150

1.81E+01
1.81E+01
0.00E+00

2.92E+00
5.25E-04
1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY302040 1

I
0.50
I0852035 3655

StaL

0.845

0.248 -2.00E+00
0.575 4.20E+02
0.023
1.150

1.61E+01 -1.84E+00
8.09E+00 2.42E-02
0.00E+00 1.00E+01

3.20E+00
1.07E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
3 , 2

MY301040 1

I
0.50
I0852035 3612

StaL

0.810

0.214 -1.73E+00
0.572 4.20E+02
0.024
1.150

1.61E+01 -1.83E+00
8.09E+00 2.53E-02
0.00E+00 1.00E+01

3.20E+00
1.07E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
3 , 2

MY702040 1

I
0.50
I0852035 4276

StaL

0.800

0.246 -1.99E+00
0.540 4.20E+02
0.014
1.150

1.61E+01 1.83E+00
8.09E+00 -2.22E-02
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 2

MY701010 1

I
0.50
I1252035 4200

Lbck

0.788

0.000
0.787
0.001

2.10E+01
2.10E+01
0.00E+00

3.95E+00
1.77E-03
1.00E+01

5.01E+00
1.64E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 2

MY701040 1

I
0.50
I0852035 4233

StaL

0.767

0.212 -1.71E+00
0.540 4.20E+02
0.015
1.150

1.61E+01 1.83E+00
8.09E+00 -2.40E-02
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY502020 1

I
0.45
I1252035 3943

StaL

0.766

0.014 -1.21E-01
0.751 4.20E+02
0.000
1.150

2.01E+01 3.77E+00
8.50E+00 -2.14E-04
0.00E+00 1.00E+01

5.01E+00
1.64E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 2

MX402010 1

I
HE800B

0.40
3838

StaL

0.765

0.031 -1.71E-01
0.713 3.55E+02
0.020
1.150

9.42E+00 -1.35E+00
5.44E+00 6.13E-03
0.00E+00 5.00E+00

1.90E+00
3.06E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
4 , 1

MY501030 1

I
0.45
I0852035 3912

Lbck

0.757

0.000
0.757
0.000

9.72E-03
4.20E+02
1.150

1.81E+01 2.56E+00
1.81E+01 -3.65E-04
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY502030 1

I
0.45
I0852035 3954

Lbck

0.757

0.000
0.757
0.000

1.03E-02
4.20E+02
1.150

1.81E+01
1.81E+01
0.00E+00

2.56E+00
2.79E-04
1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY702010 1

I
0.50
I1252035 4243

Lbck

0.745

0.000
0.745
0.000

1.25E+00
4.20E+02
1.150

2.10E+01 3.73E+00
2.10E+01 -3.85E-04
0.00E+00 1.00E+01

5.01E+00
1.64E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MF302020 1

BOX
B040420

0.50
3627

Stab

0.702

0.509 -2.54E+00
0.193 3.55E+02
0.000
1.150

4.99E+00 -2.58E-01
4.99E+00 9.89E-19
0.00E+00 1.20E+01

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

1.20E+01
1.20E+01
1 , 1

MX502010 1

I
HE800B

0.40
4000

StaL

0.701

0.034 -1.90E-01
0.655 3.55E+02
0.013
1.150

1.01E+01 -1.35E+00
5.62E+00 6.09E-03
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

MY102010 1

I
HE800B

0.50
3334

Lbck

0.690

0.000
0.653
0.037

4.95E-01
3.55E+02
1.150

1.01E+01
1.01E+01
0.00E+00

7.64E-01
1.75E-02
1.00E+01

1.17E+00
4.76E-01
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 1

MY101010 1

I
HE800B

0.50
3293

Lbck

0.685

0.000
0.654
0.032

4.92E-01
3.55E+02
1.150

1.01E+01
1.01E+01
0.00E+00

7.65E-01
1.50E-02
1.00E+01

1.17E+00
4.76E-01
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 1

MY301010 1

I
0.50
I1252035 3579

Lbck

0.684

0.000
0.683
0.001

8.03E-01
4.20E+02
1.150

2.10E+01 3.42E+00
2.10E+01 -1.21E-03
0.00E+00 1.00E+01

5.01E+00
1.64E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 2

MF702020 1

BOX
B040420

0.50
4248

Stab

0.672

0.456 -2.27E+00
0.216 3.55E+02
0.000
1.150

4.99E+00 -2.89E-01
4.99E+00 3.32E-18
0.00E+00 1.20E+01

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

1.20E+01
1.20E+01
1 , 1

MX702010 1

I
HE800B

0.40
4313

StaL

0.656

0.091 -4.94E-01
0.564 3.55E+02
0.001
1.150

9.42E+00
5.44E+00
0.00E+00

1.90E+00
3.06E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
4 , 1

6.79E-01
4.20E+02
1.150

1.07E+00
3.91E-04
5.00E+00

84

Member

LoadCase CND Type

Phase
SctNam

Joint/Po Outcome
EleNum

UsfTot

UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z Class w,f
---------------------------------------------------------------------------------------------------------------------------MX302020 1
I
0.40
StaL
0.642
0.010 -1.50E-01 1.80E+01 -3.06E+00 4.89E+00
1.000
5.00E+00
I0852035 3697
0.626 4.20E+02 1.44E+01 9.99E-03 1.62E+00
1.000
5.00E+00
0.006
1.150
0.00E+00 5.00E+00
1.000
C , C
1 , 2
MY302010 1

I
0.50
I1252035 3622

Lbck

0.641

0.000
0.641
0.000

MX202020 1

I
0.40
I0852035 3530

StaL

0.638

MZ501010 1

BOX
B040440

0.50
3882

Stab

MY902010 1

I
0.50
I0852035 4548

MY901010 1

3.21E+00
4.08E-04
1.00E+01

5.01E+00
1.64E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

0.008 -1.13E-01
0.625 4.20E+02
0.005
1.150

1.80E+01 -3.05E+00
1.44E+01 8.87E-03
0.00E+00 5.00E+00

4.89E+00
1.62E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 2

0.633

0.226 -3.60E+00
0.399 4.20E+02
0.007
1.150

1.60E+01
1.60E+01
0.00E+00

1.14E+00
2.12E-02
6.70E+00

2.85E+00
2.85E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

Lbck

0.625

0.000
0.578
0.047

6.21E-01
4.20E+02
1.150

1.81E+01 1.96E+00
1.81E+01 -7.64E-02
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

I
0.50
I0852035 4511

Lbck

0.624

0.000
0.578
0.046

6.30E-01
4.20E+02
1.150

1.81E+01 1.95E+00
1.81E+01 -7.51E-02
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY701020 1

I
0.45
I1242035 4211

StaL

0.622

0.070 -3.49E-01
0.545 4.20E+02
0.006
1.150

1.76E+01 -1.69E+00
4.97E+00 -4.38E-03
0.00E+00 1.00E+01

3.10E+00
6.83E-01
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
3 , 1

MZ504010 1

BOX
B040440

0.50
3970

Stab

0.620

0.150 -2.39E+00
0.462 4.20E+02
0.008
1.150

1.60E+01 -1.32E+00
1.60E+01 2.20E-02
0.00E+00 6.70E+00

2.85E+00
2.85E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MY501040 1

I
0.50
I0852035 3923

StaL

0.603

0.088 -7.13E-01
0.515 4.20E+02
0.000
1.150

1.61E+01
8.09E+00
0.00E+00

1.74E+00
5.52E-05
1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY301020 1

I
0.45
I1242035 3590

StaL

0.603

0.071 -3.53E-01
0.525 4.20E+02
0.006
1.150

1.76E+01 -1.63E+00
4.97E+00 4.31E-03
0.00E+00 1.00E+01

3.10E+00
6.83E-01
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
3 , 1

MX601040 1

I
0.40
I0852035 4141

StaL

0.596

0.216 -3.10E+00
0.287 4.20E+02

1.80E+01 -1.28E+00
1.44E+01 -9.89E-02

4.47E+00
1.07E+00

1.000
1.000

5.00E+00
5.00E+00

MZ504020 1

BOX
B040440

0.50
3971

Stab

0.594

0.103 -1.65E+00
0.487 4.20E+02
0.003
1.150

1.60E+01 1.39E+00
1.60E+01 -9.17E-03
0.00E+00 6.70E+00

2.85E+00
2.85E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MY502040 1

I
0.50
I0852035 3965

StaL

0.591

0.076 -6.17E-01
0.515 4.20E+02
0.000
1.150

1.61E+01 1.74E+00
8.09E+00 -5.52E-05
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MX301040 1

I
0.40
I0852035 3687

StaL

0.581

0.212 -3.04E+00
0.280 4.20E+02
0.090
1.150

1.80E+01 -1.25E+00
1.44E+01 -9.56E-02
0.00E+00 5.00E+00

4.47E+00
1.07E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 2

MZ501020 1

BOX
B040440

0.50
3883

Stab

0.578

0.099 -1.57E+00
0.477 4.20E+02
0.002
1.150

1.60E+01 -1.36E+00
1.60E+01 -5.95E-03
0.00E+00 6.70E+00

2.85E+00
2.85E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MX602010 1

I
HE800B

0.40
4146

StaL

0.565

0.099 -5.40E-01
0.464 3.55E+02
0.002
1.150

9.42E+00 -8.80E-01
5.44E+00 -5.05E-04
0.00E+00 5.00E+00

1.90E+00
3.06E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
4 , 1

MY401030 1

I
0.45
I0852035 3759

Lbck

0.558

0.000
0.557
0.001

2.48E-02
4.20E+02
1.150

1.81E+01
1.81E+01
0.00E+00

1.89E+00
9.32E-04
1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY402030 1

I
0.45
I0852035 3801

Lbck

0.548

0.000
0.547
0.000

2.69E-02
4.20E+02
1.150

1.81E+01 1.85E+00
1.81E+01 -5.55E-04
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY801010 1

I
0.50
I0852035 4359

Lbck

0.541

0.000
0.539
0.002

4.14E-01
4.20E+02
1.150

1.81E+01
1.81E+01
0.00E+00

1.82E+00
3.36E-03
1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY302020 1

I
0.45
I1242035 3633

Lbck

0.539

0.000
0.538
0.001

3.10E-02
4.20E+02
1.150

1.85E+01 1.74E+00
1.85E+01 -1.37E-03
0.00E+00 1.00E+01

3.23E+00
1.06E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 1

MY702020 1

I
0.45
I1242035 4254

StaL

0.536

0.007 -3.58E-02
0.528 4.20E+02
0.001
1.150

1.76E+01 -1.70E+00
4.97E+00 1.16E-03
0.00E+00 1.00E+01

3.23E+00
1.06E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 1

MX802010 1

I
HE800B

StaL

0.534

0.017 -9.63E-02
0.517 3.55E+02
0.000
1.150

1.01E+01 1.07E+00
5.62E+00 -1.44E-04
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

0.40
4458

1.37E+00
4.20E+02
1.150

2.10E+01
2.10E+01
0.00E+00

85

Member

LoadCase CND Type

Phase
SctNam

Joint/Po Outcome
EleNum

UsfTot

UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z Class w,f
---------------------------------------------------------------------------------------------------------------------------MY802010 1
I
0.50
Lbck
0.531
0.000 3.96E-01 1.81E+01 1.79E+00 3.38E+00
1.000
1.00E+01
I0852035 4401
0.529 4.20E+02 1.81E+01 3.29E-03 1.62E+00
1.000
1.00E+01
0.002
1.150
0.00E+00 1.00E+01
1.000
C , C
1 , 2
MX402040 1

I
HE600B

0.40
3854

StaL

0.530

0.308 -1.48E+00
0.222 3.55E+02
0.000
1.150

7.89E+00 2.78E-01
4.81E+00 -1.26E-04
0.00E+00 5.00E+00

1.25E+00
2.78E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX502040 1

I
HE600B

0.40
4016

StaL

0.526

0.308 -1.48E+00
0.217 3.55E+02
0.001
1.150

7.89E+00 2.73E-01
4.81E+00 -1.62E-04
0.00E+00 5.00E+00

1.25E+00
2.78E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MY402020 1

I
0.45
I0852035 3790

StaL

0.524

0.025 -2.01E-01
0.497 4.20E+02
0.002
1.150

1.61E+01 1.68E+00
8.09E+00 -3.05E-03
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MX602020 1

I
0.40
I0852035 4151

StaL

0.520

0.008 -1.08E-01
0.506 4.20E+02
0.007
1.150

1.80E+01 -2.47E+00
1.44E+01 1.09E-02
0.00E+00 5.00E+00

4.89E+00
1.62E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 2

MY601040 1

I
0.50
I0852035 4075

StaL

0.516

0.129 -1.05E+00
0.382 4.20E+02
0.005
1.150

1.61E+01
8.09E+00
0.00E+00

1.29E+00
7.96E-03
1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MX702020 1

I
0.40
I0852035 4318

StaL

0.514

0.002 -3.33E-02
0.505 4.20E+02
0.006
1.150

1.80E+01 -2.47E+00
1.44E+01 9.78E-03
0.00E+00 5.00E+00

4.89E+00
1.62E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 2

MY401040 1

I
0.50
I0852035 3770

StaL

0.513

0.128 -1.04E+00
0.379 4.20E+02
0.005
1.150

1.61E+01 1.28E+00
8.09E+00 -7.89E-03
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

MY601030 1

I
0.45
I0852035 4064

Lbck

0.508

0.000
0.508
0.001

1.81E+01 1.72E+00
1.81E+01 -8.36E-04
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
1 , 2

2.77E-02
4.20E+02
1.150

86

FRAMEWORK MEMBERCHECK LIFT SINGLE CRITICAL MEMBER

******
********
**
**
**
*******
*******
**
**
**
********
******

******
********
**
**
**
**
**********
*********
**
**
**
********
******

******
********
**
**
**
*******
*******
**
**
**
********
******

******
********
**
**
**
*********
**********
**
**
**
**
*********
****** **

** *** ****
*************
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**

*********************************************************************************************
*********************************************************************************************
**
**
**
**
**
******* ******
*****
*
* ******* *
*
*****
******
*
*
**
**
*
*
* *
* **
** *
*
* *
* *
* *
*
**
**
*
*
* *
* * * * * *
*
* *
* *
* * *
**
**
*****
******
******* * * * *****
* * * *
* ******
***
**
**
*
*
*
*
* *
* *
* * * *
* *
*
* *
**
**
*
*
*
*
* *
* *
* * * *
* *
*
*
*
**
**
*
*
* *
* *
* *******
** **
*****
*
* *
*
**
**
**
**
**
**
Postprocessing of Frame Structures
**
**
**
**
**
*********************************************************************************************
*********************************************************************************************
Marketing and Support by DNV Software
Program id
Release date
Access time
User id

: 3.6-02
: 7-JUN-2011
: 12-JUN-2012 09:22:14
: 123333

Computer
Impl. update
Operating system
CPU id
Installation

:
:
:
:
:

586
Win NT 6.1 [7601]
0476028815
, EURW120334

Copyright DET NORSKE VERITAS AS, P.O.Box 300, N-1322 Hovik, Norway
DATE: 12-JUN-2012 TIME: 09:22:14

PROGRAM: SESAM

FRAMEWORK 3.6-02

7-JUN-2011

MEMBER check: EC3/NS3472 ENV 1993-1-1/Ed 3

Run:
Superelement:
Loadset:
LIFT_2
T201
LIFT
Priority....: Worst Loadcase
Usage factor: Above
0.05

PAGE:

SUB PAGE:

NOMENCLATURE:
Member
LoadCase
CND
Type
Joint/Po
Outcome
UsfTot
UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
Phase
SctNam
EleNum
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z
Class w,f

Name of member
Name of loadcase
Operational, storm or earthquake condition
Section type
Joint name or position within the member
Outcome message from the code check
Total usage factor: UsfTot = UsfAx + UsfMy + UsfMz
Usage factor due to axial stress
Acting axial force
Axial (buckling) force capacity about y-axis
Design bending moment used for bending about y-axis
Moment capacity for bending about y-axis
Effective length factor for bending about y-axis
Buckling length for bending about y-axis
Phase angle in degrees
Section name
Element number
Usage factor due to bending about y-axis
Yield strength
Axial (buckling) force capacity about z-axis
Design bending moment used for bending about z-axis
Moment capacity for bending about z-axis
Effective length factor for bending about z-axis
Buckling length for bending about z-axis
Usage factor due to bending about z-axis
Material factor, gamma-M1
Equivalent stress used in von Mises stress check
Length between lateral support of compression flange
Lateral buckling factor
Buckling curve for bending about y,z-axes
Cross section class for web, flange
MEMBER check: EC3/NS3472 ENV 1993-1-1/Ed 3
Run:
Superelement:
Loadset:
LIFT_2
T201
LIFT
Priority....: Worst Loadcase
Usage factor: Above
0.05

87

Member

LoadCase CND Type

Phase
SctNam

Joint/Po Outcome
EleNum

UsfTot

UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z Class w,f
---------------------------------------------------------------------------------------------------------------------------MX601040 2
I
0.40
StaL
0.676
0.244 -3.50E+00 1.80E+01 -1.45E+00 4.47E+00
1.000
5.00E+00
I0852035 4141
0.325 4.20E+02 1.44E+01 -1.14E-01 1.07E+00
1.000
5.00E+00
0.107
1.150
0.00E+00 5.00E+00
1.000
C , C
3 , 2
MX301040 2

I
0.40
I0852035 3687

StaL

0.660

0.239 -3.44E+00
0.317 4.20E+02
0.104
1.150

1.80E+01 -1.42E+00
1.44E+01 -1.11E-01
0.00E+00 5.00E+00

4.47E+00
1.07E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 2

MX304040 2

I
0.40
I0852035 3724

StaL

0.611

0.216 -3.10E+00
0.292 4.20E+02
0.103
1.150

1.80E+01 -1.31E+00
1.44E+01 1.10E-01
0.00E+00 5.00E+00

4.47E+00
1.07E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 2

MX604040 2

I
0.40
I0852035 4178

StaL

0.542

0.211 -3.03E+00
0.271 4.20E+02
0.060
1.150

1.80E+01 -1.33E+00
1.44E+01 9.71E-02
0.00E+00 5.00E+00

4.89E+00
1.62E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
2 , 2

MC651030 2

BOX
B040420

J701040
4185

AxLd

0.444

0.444
0.000
0.000

4.17E+00
3.55E+02
1.150

9.38E+00
9.38E+00
0.00E+00

2.36E-02
1.00E-10
7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MD301040 2

BOX
B040420

J301040
3668

AxLd

0.430

0.430
0.000
0.000

4.04E+00
3.55E+02
1.150

9.38E+00
9.38E+00
0.00E+00

3.06E-02
1.00E-10
7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MC254030 2

BOX
B040420

J304040
3569

AxLd

0.368

0.368
0.000
0.000

3.46E+00
3.55E+02
1.150

9.38E+00 -8.17E-03
9.38E+00 1.00E-10
0.00E+00 7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MC654030 2

BOX
B040420

J704040
4190

AxLd

0.359

0.359
0.000
0.000

3.37E+00
3.55E+02
1.150

9.38E+00 -6.66E-03
9.38E+00 1.00E-10
0.00E+00 7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MD704040 2

BOX
B040420

J704040
4294

AxLd

0.354

0.354
0.000
0.000

3.32E+00
3.55E+02
1.150

9.38E+00 -4.00E-03
9.38E+00 1.00E-10
0.00E+00 7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MD304040 2

BOX
B040420

J304040
3673

AxLd

0.353

0.353
0.000
0.000

3.31E+00
3.55E+02
1.150

9.38E+00
9.38E+00
0.00E+00

6.87E-03
1.00E-10
7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MD701040 2

BOX
B040420

J701040
4289

AxLd

0.343

0.343
0.000
0.000

3.22E+00
3.55E+02
1.150

9.38E+00 -2.39E-02
9.38E+00 1.00E-10
0.00E+00 7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MX701040 2

I
0.40
I0852035 4308

StaL

0.340

0.007 -1.08E-01
0.288 4.20E+02
0.044
1.150

1.80E+01 -1.41E+00
1.44E+01 -7.16E-02
0.00E+00 5.00E+00

4.89E+00
1.62E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 2

MX201040 2

I
0.40
I0852035 3520

StaL

0.328

0.009 -1.24E-01
0.277 4.20E+02
0.043
1.150

1.80E+01 -1.35E+00
1.44E+01 -6.93E-02
0.00E+00 5.00E+00

4.89E+00
1.62E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 2

MX704040 2

I
0.40
I0852035 4345

StaL

0.324

0.009 -1.24E-01
0.273 4.20E+02
0.042
1.150

1.80E+01 -1.33E+00
1.44E+01 6.90E-02
0.00E+00 5.00E+00

4.89E+00
1.62E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 2

MX204040 2

I
0.40
I0852035 3557

StaL

0.320

0.010 -1.46E-01
0.265 4.20E+02
0.045
1.150

1.80E+01 -1.29E+00
1.44E+01 7.25E-02
0.00E+00 5.00E+00

4.89E+00
1.62E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 2

MC251030 2

BOX
B040420

J301040
3564

AxLd

0.319

0.319
0.000
0.000

2.99E+00
3.55E+02
1.150

9.38E+00 -3.27E-02
9.38E+00 1.00E-10
0.00E+00 7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MZ304030 2

BOX
B060640

J304040
3663

AxLd

0.209

0.209
0.000
0.000

6.83E+00
4.20E+02
1.150

3.27E+01 -2.10E+00
3.27E+01 1.00E-10
0.00E+00 6.60E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.60E+00
6.60E+00
1 , 1

MZ704030 2

BOX
B060640

J704040
4284

AxLd

0.198

0.198
0.000
0.000

6.49E+00
4.20E+02
1.150

3.27E+01 -2.08E+00
3.27E+01 1.00E-10
0.00E+00 6.60E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.60E+00
6.60E+00
1 , 1

MZ701030 2

BOX
B060640

J701040
4194

AxLd

0.186

0.186
0.000
0.000

6.10E+00
4.20E+02
1.150

3.27E+01
3.27E+01
0.00E+00

2.08E+00
1.00E-10
6.60E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.60E+00
6.60E+00
1 , 1

MZ301030 2

BOX
B060640

J301040
3573

AxLd

0.184

0.184
0.000
0.000

6.03E+00
4.20E+02
1.150

3.27E+01
3.27E+01
0.00E+00

2.09E+00
1.00E-10
6.60E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.60E+00
6.60E+00
1 , 1

88

FRAMEWORK MEMBER CHECK, TRANSPORT

1
******
********
**
**
**
*******
*******
**
**
**
********
******

******
********
**
**
**
**
**********
*********
**
**
**
********
******

******
********
**
**
**
*******
*******
**
**
**
********
******

******
********
**
**
**
*********
**********
**
**
**
**
*********
****** **

** *** ****
*************
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**

*********************************************************************************************
*********************************************************************************************
**
**
**
**
**
******* ******
*****
*
* ******* *
*
*****
******
*
*
**
**
*
*
* *
* **
** *
*
* *
* *
* *
*
**
**
*
*
* *
* * * * * *
*
* *
* *
* * *
**
**
*****
******
******* * * * *****
* * * *
* ******
***
**
**
*
*
*
*
* *
* *
* * * *
* *
*
* *
**
**
*
*
*
*
* *
* *
* * * *
* *
*
*
*
**
**
*
*
* *
* *
* *******
** **
*****
*
* *
*
**
**
**
**
**
**
Postprocessing of Frame Structures
**
**
**
**
**
*********************************************************************************************
*********************************************************************************************
Marketing and Support by DNV Software
Program id
Release date
Access time
User id

: 3.6-02
: 7-JUN-2011
: 12-JUN-2012 09:23:46
: 123333

Computer
Impl. update
Operating system
CPU id
Installation

:
:
:
:
:

586
Win NT 6.1 [7601]
0476028815
, EURW120334

Copyright DET NORSKE VERITAS AS, P.O.Box 300, N-1322 Hovik, Norway
DATE: 12-JUN-2012 TIME: 09:23:46

PROGRAM: SESAM

FRAMEWORK 3.6-02

7-JUN-2011

MEMBER check: EC3/NS3472 ENV 1993-1-1/Ed 3

Run:
Superelement:
Loadset:
ULS
T197
INPLACE
Priority....: Worst Loadcase
Usage factor: Above
0.50

SUB PAGE:

NOMENCLATURE:
Member
LoadCase
CND
Type
Joint/Po
Outcome
UsfTot
UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
Phase
SctNam
EleNum
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z
Class w,f

Name of member
Name of loadcase
Operational, storm or earthquake condition
Section type
Joint name or position within the member
Outcome message from the code check
Total usage factor: UsfTot = UsfAx + UsfMy + UsfMz
Usage factor due to axial stress
Acting axial force
Axial (buckling) force capacity about y-axis
Design bending moment used for bending about y-axis
Moment capacity for bending about y-axis
Effective length factor for bending about y-axis
Buckling length for bending about y-axis
Phase angle in degrees
Section name
Element number
Usage factor due to bending about y-axis
Yield strength
Axial (buckling) force capacity about z-axis
Design bending moment used for bending about z-axis
Moment capacity for bending about z-axis
Effective length factor for bending about z-axis
Buckling length for bending about z-axis
Usage factor due to bending about z-axis
Material factor, gamma-M1
Equivalent stress used in von Mises stress check
Length between lateral support of compression flange
Lateral buckling factor
Buckling curve for bending about y,z-axes
Cross section class for web, flange

DATE: 12-JUN-2012 TIME: 09:23:46

PROGRAM: SESAM

FRAMEWORK 3.6-02

7-JUN-2011

MEMBER check: EC3/NS3472 ENV 1993-1-1/Ed 3

Run:
Superelement:
Loadset:
ULS
T197
INPLACE
Priority....: Worst Loadcase

89

Member

LoadCase CND Type

Phase
SctNam

Joint/Po Outcome
EleNum

UsfTot

UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z Class w,f
---------------------------------------------------------------------------------------------------------------------------MX601020 601
I
0.50
*Fa StaL
1.029
0.105 -5.91E-01 1.01E+01 -1.84E+00 2.07E+00
1.000
5.00E+00
HE800B
351
0.888 3.55E+02 5.62E+00 -1.71E-02 4.76E-01
1.000
5.00E+00
0.036
1.150
0.00E+00 5.00E+00
1.000
C , C
1 , 1
MX301020 609

I
HE800B

0.50
247

*Fa StaL

1.029

0.102 -5.75E-01
0.897 3.55E+02
0.029
1.150

1.01E+01 -1.85E+00
5.62E+00 -1.40E-02
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

MX304020 609

I
HE800B

0.50
256

*Fa StaL

1.013

0.078 -4.40E-01
0.893 3.55E+02
0.043
1.150

1.01E+01 -1.84E+00
5.62E+00 2.03E-02
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

MX604020 601

I
HE800B

0.50
360

StaL

0.997

0.088 -4.96E-01
0.869 3.55E+02
0.040
1.150

1.01E+01 -1.80E+00
5.62E+00 1.92E-02
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

MD454020 617

BOX
B040420

0.50
291

Stab

0.990

0.617 -4.44E+00
0.301 3.55E+02
0.072
1.150

7.20E+00
7.20E+00
0.00E+00

4.03E-01
9.60E-02
7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MC504010 625

BOX
B040420

0.50
316

Stab

0.971

0.608 -4.37E+00
0.297 3.55E+02
0.067
1.150

7.20E+00
7.20E+00
0.00E+00

3.97E-01
8.94E-02
7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MD304020 617

BOX
B020216

0.50
255

Stab

0.971

0.877 -1.05E+00
0.095 3.55E+02
0.000
1.150

1.20E+00
1.20E+00
0.00E+00

2.38E-02
1.17E-18
8.36E+00

2.51E-01
2.51E-01
0.000

1.000
1.000
C , C

8.36E+00
8.36E+00
1 , 1

MD451020 617

BOX
B040420

0.50
289

Stab

0.952

0.580 -4.17E+00
0.308 3.55E+02
0.064
1.150

7.20E+00 4.12E-01
7.20E+00 -8.60E-02
0.00E+00 7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MC604010 625

BOX
B020216

0.50
359

Stab

0.944

0.851 -1.02E+00
0.094 3.55E+02
0.000
1.150

1.20E+00
1.20E+00
0.00E+00

2.36E-02
4.08E-19
8.36E+00

2.51E-01
2.51E-01
0.000

1.000
1.000
C , C

8.36E+00
8.36E+00
1 , 1

MC501010 625

BOX
B040420

0.50
314

Stab

0.941

0.579 -4.17E+00
0.303 3.55E+02
0.059
1.150

7.20E+00 4.05E-01
7.20E+00 -7.89E-02
0.00E+00 7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MD301020 617

BOX
B020216

0.50
246

Stab

0.915

0.826 -9.93E-01
0.089 3.55E+02
0.000
1.150

1.20E+00 2.23E-02
1.20E+00 -1.19E-18
0.00E+00 8.36E+00

2.51E-01
2.51E-01
0.000

1.000
1.000
C , C

8.36E+00
8.36E+00
1 , 1

0.811 -9.76E-01 1.20E+00 2.25E-02 2.51E-01

0.089 3.55E+02 1.20E+00 -1.32E-18 2.51E-01
0.000
1.150
0.00E+00 8.36E+00
0.000

1.000
1.000
C , C

8.36E+00
8.36E+00
1 , 1

MC601010 625

BOX
0.50
B020216 350

Stab

0.900

MX301010 609

I
0.50
I1242035 245

StaL

0.877

0.235 -2.80E+00
0.515 4.20E+02
0.127
1.150

1.85E+01 -2.81E+00
1.19E+01 8.69E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX304010 609

I
0.50
I1242035 254

StaL

0.866

0.244 -2.91E+00
0.512 4.20E+02
0.110
1.150

1.85E+01 -2.78E+00
1.19E+01 -7.49E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX601010 601

I
0.50
I1242035 349

StaL

0.862

0.235 -2.80E+00
0.529 4.20E+02
0.097
1.150

1.85E+01 -2.88E+00
1.19E+01 6.62E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX604010 601

I
0.50
I1242035 358

StaL

0.852

0.247 -2.94E+00
0.527 4.20E+02
0.079
1.150

1.85E+01 -2.87E+00
1.19E+01 -5.38E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MF302020 605

BOX
B040420

0.50
231

Stab

0.851

0.759 -3.79E+00
0.092 3.55E+02
0.000
1.150

4.99E+00 -1.24E-01
4.99E+00 3.12E-18
0.00E+00 1.20E+01

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

1.20E+01
1.20E+01
1 , 1

MX404010 609

I
0.50
I1242035 286

StaL

0.841

0.207 -2.46E+00
0.511 4.20E+02
0.124
1.150

1.85E+01 -2.78E+00
1.19E+01 8.46E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX504010 601

I
0.50
I1242035 326

StaL

0.831

0.211 -2.52E+00
0.526 4.20E+02
0.094
1.150

1.85E+01 -2.86E+00
1.19E+01 -6.44E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX401010 625

I
0.50
I1242035 278

StaL

0.825

0.183 -2.18E+00
0.506 4.20E+02
0.137
1.150

1.85E+01 -2.75E+00
1.19E+01 -9.33E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX304030 609

I
HE800B

0.50
243

Lbck

0.809

0.000
0.738
0.071

1.01E+01
1.01E+01
0.00E+00

1.86E+00
3.37E-02
3.30E+00

2.51E+00
4.76E-01
1.000

1.000
1.000
C , C

3.30E+00
3.30E+00
1 , 1

MX501010 601

I
0.50
I1242035 318

StaL

0.807

0.173 -2.06E+00
0.529 4.20E+02
0.104
1.150

1.85E+01 -2.88E+00
1.19E+01 -7.11E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

9.03E-02
3.55E+02
1.150

90

Member

LoadCase CND Type

Phase
SctNam

Joint/Po Outcome
EleNum

UsfTot

UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z Class w,f
---------------------------------------------------------------------------------------------------------------------------MX651030 601
I
0.50
StaL
0.802
0.005 -3.78E-02 1.01E+01 -1.96E+00 2.51E+00
1.000
3.30E+00
HE800B
362
0.779 3.55E+02 7.68E+00 -8.37E-03 4.76E-01
1.000
3.30E+00
0.018
1.150
0.00E+00 3.30E+00
1.000
C , C
1 , 1
MF702020 605

BOX
B040420

0.50
380

Stab

0.792

0.702 -3.50E+00
0.091 3.55E+02
0.000
1.150

4.99E+00 -1.21E-01
4.99E+00 4.15E-18
0.00E+00 1.20E+01

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

1.20E+01
1.20E+01
1 , 1

MX654030 601

I
HE800B

0.50
364

StaL

0.791

0.009 -7.02E-02
0.756 3.55E+02
0.027
1.150

1.01E+01 -1.90E+00
7.68E+00 1.26E-02
0.00E+00 3.30E+00

2.51E+00
4.76E-01
1.000

1.000
1.000
C , C

3.30E+00
3.30E+00
1 , 1

MX301030 609

I
HE800B

0.50
241

StaL

0.788

0.006 -4.25E-02
0.767 3.55E+02
0.015
1.150

1.01E+01 -1.93E+00
7.68E+00 -7.12E-03
0.00E+00 3.30E+00

2.51E+00
4.76E-01
1.000

1.000
1.000
C , C

3.30E+00
3.30E+00
1 , 1

MX702010 601

I
HE800B

0.50
398

StaL

0.780

0.345 -1.94E+00
0.428 3.55E+02
0.008
1.150

1.01E+01 -8.11E-01
5.62E+00 2.42E-03
0.00E+00 5.00E+00

1.90E+00
3.06E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MX202010 609

I
HE800B

0.50
204

StaL

0.767

0.351 -1.97E+00
0.409 3.55E+02
0.006
1.150

1.01E+01 -7.77E-01
5.62E+00 1.93E-03
0.00E+00 5.00E+00

1.90E+00
3.06E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
3 , 1

MY302030 607

I
0.50
I0852035 235

Lbck

0.754

0.000
0.691
0.063

1.71E-02
4.20E+02
1.150

1.81E+01 2.34E+00
1.81E+01 -1.02E-01
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
0.100
C , C

1.00E+01
1.00E+01
1 , 2

MY701010 603

I
0.50
I1252035 370

StaL

0.746

0.035 -2.95E-01
0.516 4.20E+02
0.195
1.150

2.01E+01 2.45E+00
8.50E+00 -2.08E-01
0.00E+00 1.00E+01

4.75E+00
1.07E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
3 , 2

MX804010 617

I
0.50
I1242035 435

StaL

0.736

0.456 -4.84E+00
0.162 4.20E+02
0.118
1.150

1.54E+01
1.06E+01
0.00E+00

8.82E-01
8.04E-02
5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
4 , 1

MX602010 601

I
HE800B

0.50
353

StaL

0.734

0.337 -1.89E+00
0.392 3.55E+02
0.004
1.150

1.01E+01 -8.11E-01
5.62E+00 -2.06E-03
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
2 , 1

MX302010 609

I
HE800B

0.50
249

StaL

0.727

0.341 -1.92E+00
0.381 3.55E+02
0.004
1.150

1.01E+01 -7.88E-01
5.62E+00 -2.00E-03
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
2 , 1

MY301030 613

I
0.33
I0852035 226

StaL

0.724

0.012 -1.87E-01
0.712 4.20E+02
0.001
1.150

1.61E+01 -2.41E+00
1.81E+01 1.58E-03
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
0.100
C , C

1.00E+01
1.00E+01
1 , 2

MY702030 605

I
0.50
I0852035 384

StaL

0.721

0.006 -9.76E-02
0.715 4.20E+02
0.000
1.150

1.61E+01 -2.29E+00
1.81E+01 3.86E-04
0.00E+00 1.00E+01

3.20E+00
1.07E+00
1.000

1.000
0.100
C , C

1.00E+01
1.00E+01
3 , 2

MX801010 617

I
0.50
I1242035 427

StaL

0.708

0.453 -4.81E+00
0.156 4.20E+02
0.099
1.150

1.54E+01
1.06E+01
0.00E+00

8.49E-01
6.75E-02
5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
4 , 1

ME301010 613

BOX
B040420

0.50
222

Stab

0.706

0.626 -3.12E+00
0.081 3.55E+02
0.000
1.150

4.99E+00 -1.08E-01
4.99E+00 -2.90E-17
0.00E+00 1.20E+01

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

1.20E+01
1.20E+01
1 , 1

MX701010 601

I
0.50
I1242035 394

StaL

0.701

0.318 -3.38E+00
0.255 4.20E+02
0.127
1.150

1.54E+01 -1.39E+00
1.06E+01 -8.68E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
4 , 1

MD354030 617

BOX
B040420

0.50
261

Stab

0.698

0.524 -3.77E+00
0.138 3.55E+02
0.035
1.150

7.20E+00 -1.85E-01
7.20E+00 -4.72E-02
0.00E+00 7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MY301010 607

I
0.50
I1252035 221

StaL

0.694

0.026 -2.19E-01
0.495 4.20E+02
0.174
1.150

2.01E+01
8.50E+00
0.00E+00

2.35E+00
1.85E-01
1.00E+01

4.75E+00
1.07E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
3 , 2

MY701030 613

I
0.33
I0852035 375

StaL

0.692

0.007 -1.20E-01
0.684 4.20E+02
0.001
1.150

1.61E+01 -2.31E+00
1.81E+01 1.37E-03
0.00E+00 1.00E+01

3.38E+00
1.62E+00
1.000

1.000
0.100
C , C

1.00E+01
1.00E+01
1 , 2

MC554020 625

BOX
B040420

0.50
346

Stab

0.683

0.515 -3.70E+00
0.135 3.55E+02
0.033
1.150

7.20E+00 -1.80E-01
7.20E+00 -4.46E-02
0.00E+00 7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MX101010 625

I
0.50
I1242035 169

StaL

0.678

0.444 -4.72E+00
0.156 4.20E+02
0.078
1.150

1.54E+01
1.06E+01
0.00E+00

8.48E-01
5.34E-02
5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
4 , 1

MX104010 625

I
0.50
I1242035 177

StaL

0.668

0.445 -4.73E+00
0.160 4.20E+02
0.063
1.150

1.54E+01 8.69E-01
1.06E+01 -4.33E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
4 , 1

91

Member

LoadCase CND Type

Phase
SctNam

Joint/Po Outcome
EleNum

UsfTot

UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z Class w,f
---------------------------------------------------------------------------------------------------------------------------MX201010 609
I
0.50
StaL
0.667
0.316 -3.35E+00 1.54E+01 -1.35E+00 5.44E+00
1.000
5.00E+00
I1242035 200
0.249 4.20E+02 1.06E+01 -6.97E-02 6.83E-01
1.000
5.00E+00
0.102
1.150
0.00E+00 5.00E+00
1.000
C , C
4 , 1
MX704010 601

I
0.50
I1242035 403

StaL

0.664

0.318 -3.38E+00
0.239 4.20E+02
0.107
1.150

1.54E+01 -1.30E+00
1.06E+01 7.31E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
4 , 1

MZ701010 601

BOX
B060640

0.50
367

Stab

0.656

0.362 -1.05E+01
0.193 4.20E+02
0.101
1.150

2.91E+01 -1.33E+00
2.91E+01 -6.97E-01
0.00E+00 6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MZ704010 601

BOX
B060640

0.50
387

Stab

0.656

0.346 -1.01E+01
0.203 4.20E+02
0.106
1.150

2.91E+01 1.40E+00
2.91E+01 -7.29E-01
0.00E+00 6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MY702010 601

I
0.50
I1252035 379

Lbck

0.648

0.000
0.481
0.168

1.08E-01
4.20E+02
1.150

2.10E+01 2.41E+00
2.10E+01 -2.75E-01
0.00E+00 1.00E+01

5.01E+00
1.64E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 2

ME701010 613

BOX
B040420

0.50
371

Stab

0.646

0.566 -2.82E+00
0.080 3.55E+02
0.000
1.150

4.99E+00 -1.07E-01
4.99E+00 3.14E-17
0.00E+00 1.20E+01

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

1.20E+01
1.20E+01
1 , 1

MX204010 609

I
0.50
I1242035 209

StaL

0.643

0.314 -3.33E+00
0.239 4.20E+02
0.090
1.150

1.54E+01 -1.30E+00
1.06E+01 6.15E-02
0.00E+00 5.00E+00

5.44E+00
6.83E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
4 , 1

MZ304010 609

BOX
B060640

0.50
238

Stab

0.639

0.350 -1.02E+01
0.184 4.20E+02
0.106
1.150

2.91E+01
2.91E+01
0.00E+00

1.26E+00
7.30E-01
6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MD351030 617

BOX
B040420

0.50
260

Stab

0.634

0.483 -3.47E+00
0.128 3.55E+02
0.024
1.150

7.20E+00 -1.71E-01
7.20E+00 3.15E-02
0.00E+00 7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MZ504010 601

BOX
B040440

0.50
311

Stab

0.629

0.093 -1.49E+00
0.207 4.20E+02
0.330
1.150

1.60E+01 -5.90E-01
1.60E+01 9.40E-01
0.00E+00 6.70E+00

2.85E+00
2.85E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MC551020 601

BOX
B040420

J651030
345

AxLd

0.629

0.629
0.000
0.000

9.38E+00
9.38E+00
0.00E+00

4.02E-01
2.52E-02
7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MZ301010 609

BOX
B060640

0.50
218

Stab

0.627

0.354 -1.03E+01
0.173 4.20E+02
0.101
1.150

2.91E+01 -1.19E+00
2.91E+01 6.92E-01
0.00E+00 6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MZ501010 601

BOX
B040440

0.50
293

Stab

0.625

0.132 -2.11E+00
0.166 4.20E+02
0.326
1.150

1.60E+01
1.60E+01
0.00E+00

4.74E-01
9.29E-01
6.70E+00

2.85E+00
2.85E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MZ701020 615

BOX
B060640

0.50
368

Stab

0.622

0.286 -8.32E+00
0.198 4.20E+02
0.138
1.150

2.91E+01 1.36E+00
2.91E+01 -9.51E-01
0.00E+00 6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MZ301020 611

BOX
B060640

0.50
219

Stab

0.621

0.282 -8.21E+00
0.208 4.20E+02
0.130
1.150

2.91E+01
2.91E+01
0.00E+00

1.43E+00
8.95E-01
6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MY302010 609

I
0.50
I1252035 230

Lbck

0.618

0.000
0.467
0.151

2.10E+01
2.10E+01
0.00E+00

2.34E+00
2.48E-01
1.00E+01

5.01E+00
1.64E+00
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
2 , 2

MZ304020 607

BOX
B060640

0.50
239

Stab

0.611

0.280 -8.14E+00
0.209 4.20E+02
0.122
1.150

2.91E+01 -1.44E+00
2.91E+01 8.37E-01
0.00E+00 6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MZ704020 603

BOX
B060640

0.50
388

Stab

0.602

0.274 -7.98E+00
0.192 4.20E+02
0.135
1.150

2.91E+01 -1.32E+00
2.91E+01 -9.30E-01
0.00E+00 6.70E+00

6.88E+00
6.88E+00
0.000

1.000
1.000
C , C

6.70E+00
6.70E+00
1 , 1

MC204010 627

BOX
B020216

0.50
210

Stab

0.577

0.513 -6.17E-01
0.020 3.55E+02
0.043
1.150

1.20E+00 -5.15E-03
1.20E+00 1.08E-02
0.00E+00 8.36E+00

2.51E-01
2.51E-01
0.000

1.000
1.000
C , C

8.36E+00
8.36E+00
1 , 1

MY901040 605

I
HE800B

0.50
451

StaL

0.572

0.463 -9.55E-01
0.095 3.55E+02
0.015
1.150

8.52E+00 -1.07E-01
2.06E+00 4.46E-03
0.00E+00 1.00E+01

1.12E+00
3.06E-01
1.000

1.000
1.000
C , C

1.00E+01
1.00E+01
4 , 1

MC201010 623

BOX
B020216

0.50
201

Stab

0.567

0.504 -6.07E-01
0.020 3.55E+02
0.043
1.150

1.20E+00 -4.96E-03
1.20E+00 -1.08E-02
0.00E+00 8.36E+00

2.51E-01
2.51E-01
0.000

1.000
1.000
C , C

8.36E+00
8.36E+00
1 , 1

MF902520 607

BOX
B040420

0.50
463

Stab

0.566

0.223 -1.61E+00
0.186 3.55E+02
0.158
1.150

7.20E+00
7.20E+00
0.00E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

5.91E+00
3.55E+02
1.150

1.75E-01
4.20E+02
1.150

2.48E-01
2.11E-01
7.49E+00

92

Member

LoadCase CND Type

Phase
SctNam

Joint/Po Outcome
EleNum

UsfTot

UsfAx
N
Ndy(Nkdy)
My*ky
Mdy
Ky
Ly
UsfMy
Fy
Ndz(Nkdy)
Mz*kz
Mdz
Kz
Lz
UsfMz
Gamma-m
vMises
Lbuck
C1
BCrv y,z Class w,f
---------------------------------------------------------------------------------------------------------------------------MY501020 609
I
0.50
StaL
0.553
0.015 -3.00E-01 2.01E+01 1.96E+00 4.75E+00
1.000
1.00E+01
I1252035 299
0.412 4.20E+02 2.10E+01 1.35E-01 1.07E+00
0.100
1.00E+01
0.127
1.150
0.00E+00 1.00E+01
1.000
C , C
3 , 2
MD704020 631

BOX
B020216

0.50
404

Stab

0.553

0.489 -5.88E-01
0.021 3.55E+02
0.043
1.150

1.20E+00 -5.26E-03
1.20E+00 1.08E-02
0.00E+00 8.36E+00

2.51E-01
2.51E-01
0.000

1.000
1.000
C , C

8.36E+00
8.36E+00
1 , 1

MX204020 603

I
HE800B

0.50
211

StaL

0.543

0.062 -3.50E-01
0.441 3.55E+02
0.039
1.150

1.01E+01 -9.12E-01
5.62E+00 1.87E-02
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

ME901010 613

BOX
B040420

0.50
445

Stab

0.536

0.259 -1.86E+00
0.197 3.55E+02
0.081
1.150

7.20E+00
7.20E+00
0.00E+00

2.63E-01
1.08E-01
7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MC651030 601

BOX
B040420

J701040
363

AxLd

0.535

0.535
0.000
0.000

5.03E+00
3.55E+02
1.150

9.38E+00 -9.85E-02
9.38E+00 1.00E-10
0.00E+00 7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MD301040 609

BOX
B040420

J301040
242

AxLd

0.532

0.532
0.000
0.000

4.99E+00
3.55E+02
1.150

9.38E+00 -9.52E-02
9.38E+00 1.00E-10
0.00E+00 7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MD701020 619

BOX
B020216

0.50
395

Stab

0.530

0.467 -5.62E-01
0.020 3.55E+02
0.043
1.150

1.20E+00 -5.06E-03
1.20E+00 -1.08E-02
0.00E+00 8.36E+00

2.51E-01
2.51E-01
0.000

1.000
1.000
C , C

8.36E+00
8.36E+00
1 , 1

MX302020 609

I
0.50
I0852035 250

Lbck

0.528

0.000
0.526
0.002

2.29E-02
4.20E+02
1.150

1.81E+01 2.57E+00
1.81E+01 -3.46E-03
0.00E+00 5.00E+00

4.89E+00
1.62E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 2

MX202020 609

I
0.50
I0852035 205

Lbck

0.527

0.000
0.521
0.006

3.76E-02
4.20E+02
1.150

1.81E+01
1.81E+01
0.00E+00

2.55E+00
9.06E-03
5.00E+00

4.89E+00
1.62E+00
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 2

MX701020 611

I
HE800B

0.50
396

StaL

0.522

0.061 -3.46E-01
0.424 3.55E+02
0.037
1.150

1.01E+01 -8.76E-01
5.62E+00 -1.74E-02
0.00E+00 5.00E+00

2.07E+00
4.76E-01
1.000

1.000
1.000
C , C

5.00E+00
5.00E+00
1 , 1

MY101010 615

I
HE800B

0.50
146

StaL

0.513

0.033 -2.99E-01
0.390 3.55E+02
0.090
1.150

9.04E+00 4.56E-01
1.01E+01 -4.30E-02
0.00E+00 1.00E+01

1.17E+00
4.76E-01
1.000

1.000
0.100
C , C

1.00E+01
1.00E+01
1 , 1

MF102520 605

BOX
B040420

0.50
156

Stab

0.508

0.310 -2.23E+00
0.182 3.55E+02
0.015
1.150

7.20E+00 -2.44E-01
7.20E+00 -2.03E-02
0.00E+00 7.49E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.49E+00
7.49E+00
1 , 1

MC654030 601

BOX
B040420

J704040
365

AxLd

0.502

0.502
0.000
0.000

4.71E+00
3.55E+02
1.150

9.38E+00 -1.14E-01
9.38E+00 1.00E-10
0.00E+00 7.38E+00

1.34E+00
1.34E+00
0.000

1.000
1.000
C , C

7.38E+00
7.38E+00
1 , 1

MY902010 609

I
0.50
I0852035 460

Lbck

0.501

0.000
0.303
0.197

2.85E-01
4.20E+02
1.150

1.81E+01
1.81E+01
0.00E+00

1.03E+00
3.21E-01
1.00E+01

3.38E+00
1.62E+00
1.000

1.000
0.100
C , C

1.00E+01
1.00E+01
1 , 2

MY901010 609

I
0.50
I0852035 449

Lbck

0.501

0.000
0.304
0.197

2.76E-01
4.20E+02
1.150

1.81E+01
1.81E+01
0.00E+00

1.03E+00
3.19E-01
1.00E+01

3.38E+00
1.62E+00
1.000

1.000
0.100
C , C

1.00E+01
1.00E+01
1 , 2

93

MEMBER ASSESSMENT
In place

94

Lift

95

Transport

96

97

98

F. DESIGN CHECK OF PADEYES

99

100

101

102

103

G. DESIGN CHECK OF JOINTS

QuickNodeCheck - Screening - Inplace - Master module
- Joint UF based on a combination of incoming members UF's
- Check "Readme" sheet for explanations
(*) - The three highest UF's are used with the worst possible
sign combination of normal stresses in a 3D Von Mises check.
Joint

Translational
(A,B,X)

Longitudinal
(Y)

Vertical
(C,D,E,F,Z)

UF (*)

Joint

Translational
(A,B,X)

Longitudinal
(Y)

Vertical
(C,D,E,F,Z)

UF (*)

J101010
J101020
J101030
J101040
J101320
J101520
J101530
J101540
J101730
J102010
J102020
J102030
J102040
J102520
J102530
J104010
J104020
J104030
J104040
J151020
J154020
J201010
J201020
J201030
J201040
J201520
J201530
J201540
J202010
J202020
J202030
J202040
J204010
J204020
J204030
J204040
J251030
J254030
J301005
J301010
J301020
J301030
J301040
J302010
J302020
J302030
J302040
J304005
J304010
J304020
J304030
J304040
J351030
J354030
J401010
J401020
J401030
J401040
J402010
J402020
J402030
J402040
J404010
J404020
J404030
J404040
J451020
J454020
J501010
J501020
J501030

0.236

0.389

0.511

0.333

0.184

0.065

0.258

0.000

0.128

0.147

0.158

0.059

0.312

0.000

0.055

0.115

0.135

0.110

0.260

0.000

0.000

0.300

0.402

0.121

0.251

0.000

0.000

0.168

0.000

0.242

0.203

0.588

0.000

0.143

0.000

0.201

0.246

0.504

0.000

0.044

0.000

0.075

0.252

0.314

0.000

0.228

0.299

0.065

0.166

0.337

0.054

0.414

0.000

0.267

0.000

0.449

0.053

0.226

0.000

0.267

0.000

0.464

0.075

0.125

0.000

0.136

0.069

0.000

0.399

0.399

0.472

0.215

0.107

0.000

0.000

0.323

0.454

0.155

0.085

0.000

0.000

0.277

0.337

0.103

0.066

0.000

0.257

0.407

0.565

0.121

0.145

0.000

0.143

0.076

0.203

0.120

0.115

0.000

0.126

0.136

0.189

0.151

0.142

0.000

0.110

0.354

0.216

0.061

0.153

0.000

0.163

0.000

0.408

0.133

0.065

0.000

0.241

0.000

0.469

0.212

0.104

0.000

0.171

0.088

0.000

0.161

0.082

0.000

0.186

0.080

0.000

0.095

0.067

0.000

0.142

0.071

0.000

0.171

0.000

0.398

0.075

0.075

0.000

0.172

0.000

0.426

0.000

0.151

0.000

0.000

0.000

0.076

0.000

0.115

0.000

0.420

0.425

0.570

0.000

0.141

0.000

0.394

0.420

0.581

0.170

0.162

0.000

0.332

0.412

0.379

0.132

0.064

0.000

0.172

0.258

0.316

0.222

0.074

0.000

0.424

0.345

0.000

0.386

0.173

0.000

0.166

0.347

0.000

0.185

0.074

0.000

0.128

0.309

0.000

0.176

0.077

0.000

0.213

0.242

0.000

0.185

0.113

0.000

0.000

0.000

0.075

0.46
0.30
0.35
0.33
0.33
0.81
0.73
0.50
0.46
0.63
0.64
0.18
0.28
0.21
0.15
0.23
0.20
0.25
0.19
0.17
0.28
0.21
0.14
0.51
0.53
0.08
0.99
0.99
0.77
0.54
0.67
0.45
0.39
0.39
0.08

0.149

0.137

0.000

0.423

0.477

0.575

1.03

0.142

0.000

0.383

0.397

0.444

0.584

1.01

0.196

0.000

0.462

0.339

0.404

0.384

0.000

0.000

0.082

0.168

0.247

0.311

0.446

0.427

0.577

1.01

Ref J304010

0.172

0.000

0.351

0.387

0.421

0.602

1.01

Ref J304020

0.163

0.000

0.371

0.363

0.407

0.380

0.148

0.097

0.000

0.186

0.366

0.426

0.145

0.064

0.000

0.380

0.312

0.000

0.123

0.070

0.000

0.219

0.391

0.000

0.074

0.064

0.000

0.168

0.304

0.000

0.277

0.214

0.000

0.217

0.383

0.000

0.169

0.075

0.000

0.000

0.000

0.087

0.78
0.72
0.60
0.54
0.41
0.53
0.09

0.227

0.102

0.000

0.452

0.476

0.601

1.07

Checked

0.285

0.115

0.000

0.388

0.456

0.624

1.05

checked

0.145

0.095

0.000

0.392

0.458

0.409

0.195

0.056

0.000

0.272

0.430

0.489

0.113

0.063

0.000

0.195

0.000

0.400

0.064

0.060

0.000

0.195

0.000

0.397

0.220

0.000

0.387

0.161

0.071

0.000

0.187

0.000

0.409

0.215

0.120

0.000

0.225

0.297

0.537

0.150

0.084

0.000

0.122

0.091

0.203

0.110

0.077

0.000

0.118

0.122

0.156

0.160

0.147

0.000

0.050

0.099

0.143

0.175

0.105

0.000

0.000

0.208

0.366

0.161

0.131

0.000

0.000

0.216

0.207

0.252

0.241

0.000

0.074

0.330

0.000

0.158

0.068

0.000

0.094

0.298

0.000

0.215

0.111

0.000

0.098

0.264

0.000

0.155

0.082

0.000

0.266

0.159

0.316

0.175

0.146

0.000

0.000

0.270

0.438

0.257

0.000

0.464

0.000

0.326

0.265

0.276

0.000

0.461

0.215

0.292

0.557

0.236

0.203

0.588

0.228

0.287

0.210

0.201

0.229

0.500

0.137

0.146

0.145

0.075

0.257

0.314

0.86
0.85
0.53
0.52
0.21
0.29
0.21
0.16
0.27
0.25
0.25
0.43
0.20
0.29
0.21
0.28
0.63
0.64
0.81
0.72
0.51

J501040
J502010
J502020
J502030
J502040
J504010
J504020
J504030
J504040
J551020
J554020
J601010
J601020
J601030
J601040
J602010
J602020
J602030
J602040
J604010
J604020
J604030
J604040
J651030
J654030
J701005
J701010
J701020
J701030
J701040
J702010
J702020
J702030
J702040
J704005
J704010
J704020
J704030
J704040
J751030
J754030
J801010
J801020
J801030
J801040
J802010
J802020
J802030
J802040
J804010
J804020
J804030
J804040
J851020
J854020
J901010
J901020
J901030
J901040
J901520
J901530
J902010
J902020
J902030
J902040
J902520
J902530
J904010
J904020
J904030
J904040

0.173

0.104

0.83
0.30
0.30
0.23
0.61
0.17
0.14
0.04
0.46
0.44
0.26
0.18
0.87
0.68
0.53
0.91
0.32
0.32
0.53
0.51
0.63
0.23
0.24
0.19
0.13
0.15
0.12
0.14
0.29
0.17
0.27
0.50
0.23
0.22
0.26
0.25
0.47
0.59
0.08

0.070

0.119

0.063

0.159

0.128

0.77
0.52
0.46
0.47
0.21
0.19
0.17
0.12
0.43
0.22
0.29
0.36
0.21
0.23
0.15
0.11
0.53
0.53
0.80
0.31
0.28
0.22
0.50
0.37
0.37
0.35
0.32
0.54
0.62
0.51
0.81
0.51
0.29
0.26

Figure G-1 Screening Inplace condition

104

QuickNodeCheck - Screening - Lift - Master Module

- Joint UF based on a combination of incoming members UF's
- Check "Readme" sheet for explanations
(*) - The three highest UF's are used with the worst possible
sign combination of normal stresses in a 3D Von Mises check.
Joint

Translational
(A,B,X)

Longitudinal
(Y)

Vertical
(C,D,E,F,Z)

UF (*)

Joint

Translational
(A,B,X)

Longitudinal
(Y)

Vertical
(C,D,E,F,Z)

UF (*)

J101010
J101020
J101030
J101040
J101320
J101520
J101530
J101540
J101730
J102010
J102020
J102030
J102040
J102520
J102530
J104010
J104020
J104030
J104040
J151020
J154020
J201010
J201020
J201030
J201040
J201520
J201530
J201540
J202010
J202020
J202030
J202040
J204010
J204020
J204030
J204040
J251030
J254030
J301005
J301010
J301020
J301030
J301040
J302010
J302020
J302030
J302040
J304005
J304010
J304020
J304030
J304040
J351030
J354030
J401010
J401020
J401030
J401040
J402010
J402020
J402030
J402040
J404010
J404020
J404030
J404040
J451020
J454020
J501010
J501020
J501030

0.118

0.382

0.373

0.526

0.155

0.603

0.177

0.468

0.073

0.048

0.109

0.291

0.507

0.000

0.040

0.063

0.111

0.207

0.552

0.000

0.000

0.164

0.238

0.262

0.447

0.000

0.000

0.073

0.000

0.214

0.190

0.518

0.000

0.015

0.000

0.320

0.379

0.659

0.000

0.053

0.000

0.077

0.497

0.595

0.000

0.137

0.153

0.170

0.291

0.545

0.097

0.433

0.000

0.287

0.000

0.522

0.050

0.180

0.000

0.274

0.000

0.410

0.090

0.124

0.000

0.114

0.113

0.369

0.276

0.051

0.269

0.224

0.167

0.000

0.000

0.189

0.271

0.289

0.151

0.000

0.000

0.167

0.161

0.288

0.113

0.000

0.122

0.415

0.382

0.255

0.144

0.000

0.083

0.075

0.153

0.330

0.145

0.000

0.057

0.020

0.055

0.285

0.304

0.000

0.039

0.034

0.078

0.352

0.376

0.000

0.181

0.000

0.309

0.146

0.104

0.325

0.197

0.000

0.370

0.199

0.156

0.000

0.081

0.123

0.229

0.263

0.142

0.000

0.174

0.101

0.000

0.257

0.114

0.000

0.194

0.108

0.000

0.312

0.000

0.547

0.095

0.089

0.000

0.277

0.000

0.430

0.000

0.163

0.000

0.000

0.000

0.000

0.000

0.193

0.000

0.158

0.409

0.502

0.000

0.186

0.000

0.266

0.291

0.349

0.359

0.251

0.000

0.227

0.684

0.495

0.231

0.150

0.000

0.594

0.623

0.527

0.309

0.164

0.000

0.469

0.567

0.000

0.262

0.152

0.000

0.571

0.092

0.453

0.076

0.114

0.211

0.172

0.514

0.000

0.122

0.089

0.000

0.313

0.450

0.000

0.336

0.224

0.000

0.000

0.000

0.000

0.097

0.090

0.000

0.163

0.477

0.559

0.237

0.000

0.382

0.228

0.294

0.337

0.375

0.000

0.457

0.163

0.667

0.508

0.000

0.000

0.000

0.539

0.616

0.539

0.144

0.378

0.458

0.252

0.000

0.415

0.266

0.276

0.343

0.255

0.000

0.433

0.208

0.700

0.503

0.078

0.160

0.249

0.580

0.620

0.526

0.091

0.065

0.000

0.343

0.509

0.000

0.201

0.109

0.000

0.714

0.117

0.466

0.099

0.090

0.000

0.211

0.558

0.000

0.478

0.307

0.000

0.312

0.447

0.000

0.157

0.088

0.000

0.000

0.000

0.000

0.240

0.185

0.000

0.149

0.444

0.515

0.268

0.159

0.000

0.231

0.291

0.315

0.089

0.151

0.225

0.140

0.807

0.557

0.234

0.058

0.000

0.543

0.626

0.552

0.193

0.098

0.000

0.328

0.000

0.536

0.097

0.088

0.000

0.304

0.000

0.432

0.238

0.000

0.390

0.106

0.118

0.354

0.309

0.000

0.419

0.250

0.185

0.000

0.136

0.435

0.599

0.306

0.162

0.000

0.082

0.158

0.255

0.288

0.113

0.000

0.077

0.036

0.111

0.368

0.147

0.000

0.041

0.039

0.115

0.479

0.189

0.000

0.000

0.121

0.317

0.364

0.305

0.000

0.000

0.132

0.127

0.355

0.374

0.000

0.123

0.500

0.000

0.119

0.108

0.308

0.019

0.116

0.000

0.265

0.201

0.000

0.072

0.231

0.000

0.284

0.154

0.000

0.266

0.062

0.251

0.261

0.113

0.000

0.000

0.133

0.334

0.296

0.000

0.495

0.000

0.220

0.114

0.301

0.000

0.369

0.131

0.443

0.585

0.221

0.157

0.505

0.155

0.170

0.251

0.481

0.446

0.644

0.118

0.055

0.101

0.126

0.495

0.589

J501040
J502010
J502020
J502030
J502040
J504010
J504020
J504030
J504040
J551020
J554020
J601010
J601020
J601030
J601040
J602010
J602020
J602030
J602040
J604010
J604020
J604030
J604040
J651030
J654030
J701005
J701010
J701020
J701030
J701040
J702010
J702020
J702030
J702040
J704005
J704010
J704020
J704030
J704040
J751030
J754030
J801010
J801020
J801030
J801040
J802010
J802020
J802030
J802040
J804010
J804020
J804030
J804040
J851020
J854020
J901010
J901020
J901030
J901040
J901520
J901530
J902010
J902020
J902030
J902040
J902520
J902530
J904010
J904020
J904030
J904040

0.283

0.088

0.67
0.24
0.17
0.16
0.35
0.07
0.02
0.05
0.25
0.49
0.21
0.19
0.48
0.40
0.28
0.70
0.23
0.10
0.11
0.43
0.50
0.33
0.24
0.27
0.16
0.16
0.19
0.19
0.53
0.33
0.42
0.36
0.31
0.18
0.49
0.16
0.54
0.72
0.00
0.75
0.61
1.09
1.17
0.74
1.05
0.69
0.66
0.00
0.85
0.58
1.21
1.17
0.76
0.64
0.47
0.38
0.41
0.36
0.46
0.60
0.58
0.63
0.42
0.40
0.38
0.33
0.69
0.58
0.70
1.11
0.95

0.228

0.088

0.043

0.032

0.106

0.78
0.96
0.70
0.68
0.62
0.72
1.01
0.95
0.78
0.71
0.60
0.48
0.34
0.39
0.36
0.35
0.42
0.51
0.63
0.45
0.31
0.36
0.33
0.75
0.62
0.00
0.82
0.63
1.07
1.18
0.90
0.90
0.62
0.66
0.00
0.92
0.60
1.05
1.16
0.58
0.60
0.37
0.14
0.27
0.16
0.69
0.21
0.37
0.37
0.35
0.27
0.26
0.16
0.55
0.63
0.92
0.38
0.17
0.16
0.39
0.22
0.57
0.13
0.27
0.45
0.42
0.29
0.91
0.41
0.20
0.14

Ref J304030
Ref J304010

Checked
Checked

Not Checked

checked

Ref J304030
Ref J304040

Ref J304030
Ref J304040

Figure G-2 Screening Lift condition

105

Joint check - Inplace - Master module

Base deck

INPUT
Node
J304010 MX1
Member
Section

MX2

MY

MZ1

MZ2

MX204010 MX304010 MY302010 MZ304005 MZ304010

I1242035 I1242035 I1252035 SUPP
B060640

RESULTS
UFmax
Dim LC
0.94
542

Material properties
gm
1.15
fy
355 MPa

Equations:

sx.1T

sx.2T

sx.3T

sx.4T

FXMX2
A Mx

A Mx
FXMX1
A Mx

sx.2B

sx.4B

A Mx

FXMX1

sx.1B

sx.3B

FXMX2

A Mx
FXMX2
A Mx

A Mx
FXMX1
A Mx

FXMX2

FXMX1

MYMX2
W y.MX
MYMX2

W y.MX
MYMX1
W y.MX

W y.MX

MYMX1

MYMX2
W y.MX
MYMX2
W y.MX

MYMX1
W y.MX
MYMX1
W y.MX

W Z.MX
MZMX2

sy.4T

W Z.MX
sy.2B

W Z.MX
MYMX2

FYMY
A MY
FYMY
A MY
FYMY
A MY

sy.4B

W Z.MX

sy.2T

MZMX1

MZMX2

MZMX2

sz.1T

W Z.MX
MZMX2

sz.2T

W Z.MX

MZMX1

sz.3T

W Z.MX
MZMX1

sz.4T

W Z.MX

FYMY
A MY

FZMZ2
A Mz
FZMZ2
A Mz
FZMZ2
A Mz
FZMZ2
A Mz

MXMY
W y.MY
MXMZ2

W y.MY

W Z.MY

MXMY
W y.MY

W y.MZ
MXMZ2
W y.MZ
MXMZ2
W y.MZ
MXMZ2
W y.MZ

W Z.MY

t xz.2.4.

MZMY

FXMZ2
2Tw.MZ BMZ
FXMY

2Tf.MY BMY

FYMZ2
2.Tf.MZ HMZ
MYMY

syz.1.2.

MZMY
W Z.MY

syz.3.4.

MYMZ2

FYMX2
2Tw.MY BMX
FYMX1
2Tw.MX BMX

MYMX2

HMX Tf.MXBMYTf.MX

MYMX2

HMX Tf.MX BMX Tf.MX

FZ
HMY tw.MY

FZ
HMX twMX
FZ
HMX tw.MX

W Z.MZ
MYMZ2
W Z.MZ
MYMZ2
W Z.MZ
MYMZ2
W Z.MZ

Continuous deck beam - x-dir

Incoming beam - column

Incoming beam - column

I1252035
1200
500
35
20
5.0
5.76E+04
2.38E+07
2.92E+06

Section
HMX
BMX
Tf-MX
Tw-MX
A MX
Wx-MX
Wy-MX
Wz-MX

I1242035
1200
400
35
20
5.06E+04
7.22E+05
1.98E+07
1.87E+06

Section
HMZ
BMZ
Tf-MZ
Tw-MZ
A MZ
Wx-MZ
Wy-MZ
Wz-MZ

Section
HMZ
BMZ
Tf-MZ
Tw-MZ
A MZ
Wx-MZ
Wy-MZ
Wz-MZ

Member

LoadC

SctNam

Fy
(kN)

MX204010
MX304010
MY302010
MZ304005
MZ304010

542
542
542
542
542

I1242035
I1242035
I1252035
SUPP
B060640

Fx
(kN)
-1687
-21
-19
2015
-66

-7
2
-476
1522
-534

Fz
(kN)
426
214
644
-7176
5889

MX204010
MX304010
MY302010
MZ304005
MZ304010

543
543
543
543
543

I1242035
I1242035
I1252035
SUPP
B060640

-1833
644
0
1312
43

-2
-5
-689
1970
-615

MX204010
MX304010
MY302010
MZ304005
MZ304010

544
544
544
544
544

I1242035
I1242035
I1252035
SUPP
B060640

-1264
1126
19
-46
139

4
-10
-525
1506
-549

Mx
(kNm)

Section
HMY
BMY
Tf-MY
Tw-MY
a
A MY
Wy-MY
Wz-MY

mm
mm
mm
mm
mm2
mm3
mm3
mm3

MZMZ2

HMZ2 Tf.MZ2BMZ.Tf.MZ

HMY Tf.MyBMYTfMY

Incoming beam - y-dir

mm
mm
mm
mm
mm
mm2
mm3
mm3

W Z.MY

MXMZ2

t xy.1.2.3.4.

MZMY

W y.MY
MXMY

MZMY

B060640
600
600
40
40
8.96E+04
2.51E+07
1.57E+07
1.57E+07

mm
mm
mm
mm
mm2
mm3
mm3
mm3
Top flange
Hot spot sx-T
sy-T
(MPa) (MPa)
1
-13
2
-24
115
3
-165
4
-147
135

-1
-1
-3170
1522
1692

My
(kNm)
2429
-372
0
-2015
-46

Mz
(kNm)
17
10
-30
0
3

402
325
714
-8802
7357

-1
-1
-3830
1970
1912

2285
-1213
0
-1312
238

5
-7
1
0
1

1
2
3
4

-78
-70
-154
-149

315
443
653
-9433
8018

-1
-1
-3203
1506
1742

1655
-2140
0
46
440

-11
-20
32
0
-1

1
2
3
4

-141
-119
-103
-114

149
149

136
115

sz-T
(MPa)
-177
45
-171
45

SUPP
850
850
60
60
1.46E+05
2.92E+06
4.67E+07
1.45E+07

mm
mm
mm
mm
mm2
mm3
mm3
mm3

Bottom flange
sx-B
sy-B
(MPa) (MPa)
25
14 -152
80
98 -131

sz-B
(MPa)
145
-49
-156
-221

Shear stresses
Von-Mises
tyz
txz
txy-T sj-T sj-B tfill
UF
(MPa)
(MPa) (MPa) (MPa) (MPa) (MPa)
9
13 173 137
0.94
9
27
13 132 155
18
13 172 211
18
27
13 257 291

-189
55
-219
25

45
111
52 -172 -140
76
-56
82 -173 -193

14
14
17
17

-172
50
-229
-6

75
-12
96 -133 -204
64
-6
53 -155 -198

19
19
13
13

30
30

28
28

14
14
14
14

168
200
199
266

102
219
121
273

0.88

14
14
14
14

164
234
201
207

92
279
76
240

0.90

Figure G-3 Local analysis Joint 304010, inplace condition

106

Joint check - Inplace - Master module

Lower deck

INPUT
Node
J304020 MX1
Member
Section

MX2

MY

MZ1

MZ2

MX204020 MX304020 MY302020 MZ304010 MZ304020

HE800B
HE800B
I1242035 B060640 B060640

RESULTS
UFmax
Dim LC
1.08

Material properties
gm
1.15

543

fy

355 MPa

Equations:

sx.1T

sx.2T

sx.3T

sx.4T

sx.1B

sx.2B

sx.3B

sx.4B

FXMX2
A Mx
FXMX2
A Mx

FXMX1
A Mx
FXMX1
A Mx

FZMZ1

sz.1B

A Mx
FXMX2
A Mx

FXMX1
A Mx
FXMX1
A Mx

W y.MX
MYMX2

FXMX2

MYMX2

W y.MX

MYMX1

MYMX1
W y.MX

MYMX2
W y.MX
MYMX2
W y.MX

MYMX1
W y.MX
MYMX1
W y.MX

sy.2T

W Z.MX
MZMX2

W y.MX

MZMX2

sy.4T

W Z.MX

MZMX1

sy.2B

W Z.MX
MZMX1

sy.4B

W Z.MX

MZMX2

sz.1T

FYMY
A MY
FYMY
A MY
FYMY
A MY
FYMY
A MY

sz.2T

sz.3T

sz.4T

W Z.MX

FZMZ2
A Mz
FZMZ2
A Mz

W Z.MX
MZMX1

A Mz

W Z.MX

MZMX1

FZMZ2

W Z.MX
MZMX2

FZMZ2
A Mz

MXMY
W y.MY
MXMZ2
W y.MY
MXMY
W y.MY
MXMY
W y.MY

MXMZ2
W y.MZ
MXMZ2
W y.MZ
MXMZ2
W y.MZ
MXMZ2
W y.MZ

A Mz

MZMY
W Z.MY

FZMZ1

sz.2B

A Mz

MZMY
W Z.MY

FZMZ1

sz.3B

A Mz

MZMY
W Z.MY

W Z.MY

FZMZ1

sz.4B

MZMY

A Mz

t xy.1.2.3.4.B.

MYMZ2
W Z.MZ

t xz.2.4.

MYMZ2
W Z.MZ

syz.1.2.

MYMZ2
W Z.MZ

Continuous deck beam - x-dir

Incoming beam - column

Section

Section

B060640

HMZ
BMZ
Tf-MZ
Tw-MZ
A MZ
Wx-MZ
Wy-MZ
Wz-MZ

600
600
40
40
8.96E+04
2.51E+07
1.57E+07
1.57E+07

1200
400
35
20
5.0
5.06E+04
1.98E+07
1.87E+06

mm
mm
mm (2)
mm (1)
mm
mm2
mm3
mm3

LoadC

SctNam

MX204020
MX304020
MY302020
MZ304010
MZ304020

523
523
523
523
523

HE800B
HE800B
I1242035
B060640
B060640

-28
66
0
-29
-16

0
0
-103
490
-337

Fz
(kN)
207
217
765
-7498
6311

MX204020
MX304020
MY302020
MZ304010
MZ304020

542
542
542
542
542

HE800B
HE800B
I1242035
B060640
B060640

91
5
-9
52
-99

-3
0
-152
520
-320

MX204020
MX304020
MY302020
MZ304010
MZ304020

543
543
543
543
543

HE800B
HE800B
I1242035
B060640
B060640

82
-17
0
-43
-50

MX204020
MX304020
MY302020
MZ304010
MZ304020

544
544
544
544
544

HE800B
HE800B
I1242035
B060640
B060640

4
7
9
-125
23

Member

HMX
BMX
Tf-MX
Tw-MX
A MX
Wx-MX
Wy-MX
Wz-MX

Fx
(kN)

800
300
33
17.5
3.26E+04
4.86E+05
8.73E+06
9.92E+05

Fy
(kN)

mm
mm
mm
mm
mm2
mm3
mm3
mm3

Mx
(kNm)

W Z.MZ

Section
HMY
BMY
Tf-MY
Tw-MY
a
A MY
Wy-MY
Wz-MY

Mz
(kNm)

MXMZ1
W y.MZ
MXMZ1
W y.MZ
MXMZ1
W y.MZ

MYMZ1

W Z.MZ
MYMZ1

W Z.MZ
MYMZ1

W Z.MZ
MYMZ1

W Z.MZ

FXMZ1
2Tf.MZ BMZ

FXMY
2Tf.MY BMY
FYMX2

FYMX1
2Tw.MX BMX

2.Tf.Mz HMZ

FYMZ1
2.Tf.Mz HMZ

MZMZ2

HMZ2 Tf.MZ2 BMZ Tf.MZ

MZMZ1

HMZ2 Tf.MZ1 BMZ Tf.MZ

MYMY

2Tw.MY BMX

FYMZ2

HMY Tf.MY BMY TfMY

MXMX2

HMX Tf.MX BMX Tf.MX

HMX Tf.MX BMX Tf.MX

MXMX2

FZMY
HMY tw.MY

FZMX2
HMX twMX
FZMX1
HMX tw.MX

Note (1):
Weld at w eb is assumed to carry shear only
Note (2):
Part pen w eld

mm
mm
mm (2)
mm (2)
mm2
mm3
mm3
mm3
Top flange
Hot spot sx-T
sy-T
(MPa) (MPa)
1
79
2
79
141
3
80
4
80
141

0
-1
-2838
1623
1230

My
(kNm)
708
-706
0
57
-53

242
78
673
-5808
4816

0
-1
-2871
1841
1044

820
-237
0
-349
-231

6
4
-5
-3
-1

1
2
3
4

31
23
91
103

-2
-2
-178
596
-350

208
188
715
-7276
6167

-1
-1
-3226
2145
1097

750
-637
0
48
-157

2
-2
0
-1
0

1
2
3
4

72
75
86
90

0
-3
-139
536
-330

147
290
692
-7937
6810

0
-1
-2962
1892
1084

561
-993
0
444
-7

-3
-6
5
1
2

1
2
3
4

108
119
68
61

0
0
0
-1
1

W y.MZ

2Tf.MZ BMZ

MYMZ2

Incoming beam - y-dir

HE800B

MXMZ1

FXMZ2

t xy.1.2.3.4.T.

syz.3.4.
I1242035

139
145

159
159

149
144

sz-T
(MPa)
-152
5
-145
11

Bottom flange
sx-B
sy-B
(MPa) (MPa)
-83
-83 141
-82
-82 141

sz-B
(MPa)
23
-183
16
-183

Shear stresses
Von-Mises
tyz
txz
txy-T sj-T
sj-B
tfill
UF
(MPa)
(MPa) (MPa) (MPa) (MPa) (MPa)
16
7 206 101
0.95
16
32
7 134 294
15
7 263
95
15
32
7 128 294

-135
-2
-106
27

-24
-31
-97
-85

30
139 -204
75
145 -204

6
6
18
18

-149
-9
-129
11

-74
-71
-85
-81

59
159 -215
52
159 -215

14
14
15
15

-146
-7
-145
-6

-120
-108
-61
-67

60
149 -181
4
144 -181

21
21
11
11

28
28

30
30

29
29

9
9
9
9

154
140
231
119

50
302
153
313

1.01

8
8
8
8

197
157
261
141

118
332
124
333

1.08

8
8
8
8

224
157
260
141

163
307
67
290

1.00

Figure G-4 Local analysis Joint 304020, inplace condition

107

Joint check - Lift - Master Module

Weather deck

INPUT
Node
J301040
Member
Section

MC
MD
MX1
MX2
MY
MZ
MC251030 MD301040 MX201040 MX301040 MY301040 MZ301030
B040420 B040420 I0852035 I0852035 I0852035 B060640

RESULTS
UFmax

Dim LC

0.87

Material properties
gm
1.15

fy

355 MPa

Equations:

MY

sX.1T

FXMX1
A MX

sX.2T

sX.1B

MYMC MYMD MYMZ FZMC FZMD FZMZ ex FXMC FXMD FXMZ

FXMX2
A MX

FXMX1
A MX

sX.2B

sX.7B

sX.8B

A MX
FXMX1
A MX
FXMX2
A MX

W Y.MX

FXMX2

MYMX1

MYMX2
W Y.MX

MYMX1
W Y.MX

W Y.MX

sY.1T

W Z.MX
MZMX2

MYMX2

MZMX1

sY.2T

W Z.MX

MZMX1

sY.1B

W Z.MX

sY.2B

MZMX2

FYMY
A MY
FYMY
A MY
FYMY
A MY
FYMY
A MY

MXMY
W Y.MY
MXMY
W Y.MY
MXMY

W Y.MY
MXMY

W Y.MY

HMX
2

FXMY

t XZ.1.2

2Tf.MY BMY

sZ.7B

FZMC FZMD FZMZ

A weld

W Y.MX
sZ.8B

MYMX2

FZMC FZMD FZMZ

A weld

W Y.MX

MYMY

HMY Tf.MY BMY Tf.MY

MZMY
W Z.MY

t YZ.1

FYMX1
2Tf.MX BMX

MZMY

t YZ.2

W Z.MY
MZMY

t YZ.7

W Z.MY
MZMY

t YZ.8

W Z.MY

FYMX2
2Tf.MX BMX
FYMX1
2Tf.MX BMX
FYMX2
2Tf.MX BMX

W Z.MX

MYMX1

MY
IY
MY
IY

L1 eX

t XY.7.8B

MXMX1

HMX Tf.MXBMXTf.MX

HMX Tf.MX BMX Tf.MX

MXMX2

FZMX1
Tw.MX HMX
FZMX2
Tw.MX HMX

MXMX1

HMX Tf.MXBMXTf.MX

HMX Tf.MXBMXTf.MX

MXMX2

FXMC FXMD FXMZ

A weld

L2 eX

Incoming beam - y-dir

Continuous deck beam - x-dir

Incoming beam - column

Incoming beam - braces

Section A-A (gusset)

Section

I0852035

Section

Section B060640

Section B040420

L1

HMY
BMY
Tf-MY
Tw-MY
a
A MY
Wy-MY
Wz-MY

800
500
35
20
6.0
4.96E+04
1.44E+07
2.92E+06

mm
mm
mm
mm (1)
mm
mm2
mm3
mm3

HMX
BMX
Tf-MX
Tw-MX
A MX
Wx-MX
Wy-MX
Wz-MX

I0852035
800
500
35
20
4.96E+04
8.12E+05
1.44E+07
2.92E+06

mm
mm
mm
mm
mm2
mm3
mm3
mm3

HMZ
BMZ
Tf-MZ
Tw-MZ
A MZ
Wx-MZ
Wy-MZ
Wz-MZ

600
600
40
40
8.96E+04
2.51E+07
1.41E+07
4.81E+06

mm
mm
mm
mm
mm2
mm3
mm3
mm3

HMZ
BMZ
Tf-MZ
Tw-MZ
A MZ
Wx-MZ
Wy-MZ
Wz-MZ

400
400
20
20
3.04E+04
5.78E+06
3.28E+06
1.07E+06

mm
mm
mm
mm
mm2
mm3
mm3
mm3

L2
T
s
ex
A
Iy

750 mm
680
50
30.0
35.0
8.58E+04
1.46E+10

mm
mm
mm (Part. pen. w eld)
mm
mm2
mm4

Figure G-5 Local analysis Joint 301040, lifting condition

108

Joint check - Lift - Master Module

Intermediate deck

INPUT
Node
J304030 MX1
Member
Section

MX2

MY

MZ1

MZ2

MX254030 MX304030 MY302030 MZ304020 MZ304030

HE800B
HE800B
I0852035 B060640 B060640

RESULTS
UFmax
Dim LC
1.00
2

Material properties
gm
1.15
fy
355 MPa

Equations:

sx.1T

sx.2T

sx.3T

sx.4T

FXMX2
A Mx

A Mx
FXMX1
A Mx

sx.2B

sx.4B

A Mx

FXMX1

sx.1B

sx.3B

FXMX2

A Mx
FXMX2
A Mx

FXMX1
A Mx
FXMX1
A Mx

W y.MX
MYMX2

FXMX2

MYMX2

W y.MX

MYMX1

MYMX1

W y.MX

MYMX2
W y.MX
MYMX2
W y.MX

MYMX1
W y.MX
MYMX1
W y.MX

sy.2T

W Z.MX
MZMX2

W y.MX

MZMX2

sy.4T

W Z.MX

MZMX1

sy.2B

W Z.MX
MZMX1

sy.4B

W Z.MX

MZMX2

FYMY
A MY
FYMY
A MY
FYMY
A MY
FYMY
A MY

sz.1T

sz.2T

sz.3T

sz.4T

W Z.MX

FZMZ2
A Mz
FZMZ2
A Mz

W Z.MX
MZMX1

A Mz

W Z.MX

MZMX1

FZMZ2

W Z.MX
MZMX2

FZMZ2
A Mz

MXMY
W y.MY
MXMZ2
W y.MY
MXMY
W y.MY
MXMY
W y.MY

MXMZ2
W y.MZ
MXMZ2
W y.MZ
MXMZ2
W y.MZ
MXMZ2
W y.MZ

MZMY

sz.1B

W Z.MY
MZMY
W Z.MY
MZMY

sz.2B

sz.3B

W Z.MY
MZMY

sz.4B

W Z.MY

MYMZ2
W Z.MZ

FZMZ1
A Mz
FZMZ1
A Mz
FZMZ1
A Mz
FZMZ1

W Z.MZ

W y.MZ
MXMZ1

W Z.MZ
MYMZ1
W Z.MZ
MYMZ1

W y.MZ
MXMZ1

W Z.MZ
MYMZ1

W y.MZ

W Z.MZ

FXMZ1
2Tf.MZ BMZ

FYMZ2
2.Tf.Mz HMZ

FYMZ1
2.Tf.Mz HMZ

MZMZ2

HMZ2 Tf.MZ2 BMZ Tf.MZ

MZMZ1

HMZ2 Tf.MZ1 BMZ Tf.MZ

MYMZ2
W Z.MZ

t xz.2.4.

FXMY
2Tf.MY BMY

MYMY

HMY Tf.MY BMY TfMY

FZMY
HMY tw.MY

MYMZ2
W Z.MZ

syz.1.2.

Continuous deck beam - x-dir

Incoming beam - column

Section
HMX
BMX
Tf-MX
Tw-MX
A MX
Wx-MX
Wy-MX
Wz-MX

Section
HMZ
BMZ
Tf-MZ
Tw-MZ
A MZ
Wx-MZ
Wy-MZ
Wz-MZ

mm
mm
mm
mm
mm2
mm3
mm3
mm3

MXMZ1

2Tf.MZ BMZ

t xy.1.2.3.4.B.

Section
HMY
BMY
Tf-MY
Tw-MY
a
A MY
Wy-MY
Wz-MY

HE800B
800
300
33
17.5
3.26E+04
4.86E+05
8.73E+06
9.92E+05

MYMZ1

W y.MZ

MYMZ2

Incoming beam - y-dir

mm
mm
mm (2)
mm (1)
mm
mm2
mm3
mm3

MXMZ1

FXMZ2

t xy.1.2.3.4.T.

syz.3.4.

I0852035
800
500
35
20
5.0
4.96E+04
1.44E+07
2.92E+06

A Mz

B060640
600
600
40
40
8.96E+04
2.51E+07
1.57E+07
1.57E+07

FYMX2
2Tw.MY BMX
FYMX1
2Tw.MX BMX

MXMX2

HMX Tf.MX BMY Tf.MX

HMX Tf.MX BMX Tf.MX

MXMX2

FZMX2
HMX twMX
FZMX1
HMX tw.MX

mm
mm
mm (2)
mm (2)
mm2
mm3
mm3
mm3

Note (1):
Weld at w eb is assumed to carry shear only
Note (2):
Part pen w eld

Member
MX254030
MX304030
MY302030
MZ304020
MZ304030

LoadC

SctNam

2
2
2
2
2

HE800B
HE800B
I0852035
B060640
B060640

Fx
(kN)
-245
261
0
-24
0

Fy
(kN)
1
1
247
377
-646

Fz
(kN)
-70
5
1326
5326
-6588

Mx
(kNm)
0
0
-3901
1733
2169

My
(kNm)
208
-298
-1
93
0

Mz
(kNm)
-1
1
0
0
0

Top flange
Hot spot sx-T
sy-T
(MPa) (MPa)
1
27
2
25
275
3
17
4
15
275

sz-T
(MPa)
-65
212
-65
212

Bottom flange
Shear stresses
Von-Mises
sx-B
sy-B sz-B
tyz
txz
txy-T sj-T
sj-B
tfill
UF
(MPa) (MPa) (MPa) (MPa)
(MPa) (MPa) (MPa) (MPa) (MPa)
-41
164
0
13
85 189
1.00
-43 -265 -57
0
83
13 268 260
-30
176
5
13 308 194
-32 -265 -45
5
83
13 276 270

Figure G-6 Local analysis Joint 304020 , lifting condition

109

Joint check - Lift - Master Module

Lower deck

INPUT
Node
J504020 MX1
Member
Section

MX2

MY

MZ1

MZ2

MX454020 MX504020 MY502020 MZ504010 MZ504020

HE800B
HE800B
I1252035 B040440 B040440

RESULTS
UFmax
Dim LC
1.07
2

Material properties
gm
1.15
fy
355 MPa

Equations:

sx.1T

sx.2T

sx.3T

sx.4T

FXMX2
A Mx

A Mx
FXMX1
A Mx

sx.2B

sx.4B

A Mx

FXMX1

sx.1B

sx.3B

FXMX2

A Mx
FXMX2
A Mx

FXMX1
A Mx
FXMX1
A Mx

W y.MX
MYMX2

FXMX2

MYMX2

W y.MX

MYMX1

MYMX1
W y.MX

MYMX2
W y.MX
MYMX2
W y.MX

MYMX1
W y.MX
MYMX1
W y.MX

sy.2T

W Z.MX
MZMX2

W y.MX

MZMX2

sy.4T

W Z.MX

MZMX1

sy.2B

W Z.MX
MZMX1

sy.4B

W Z.MX

MZMX2

FYMY
A MY
FYMY
A MY
FYMY
A MY
FYMY
A MY

sz.1T

sz.2T

sz.3T

sz.4T

W Z.MX

FZMZ2
A Mz
FZMZ2
A Mz

W Z.MX
MZMX1

A Mz

W Z.MX

MZMX1

FZMZ2

W Z.MX
MZMX2

FZMZ2
A Mz

MXMY
W y.MY
MXMZ2
W y.MY
MXMY
W y.MY
MXMY
W y.MY

MXMZ2
W y.MZ
MXMZ2
W y.MZ
MXMZ2
W y.MZ
MXMZ2
W y.MZ

MZMY

sz.1B

W Z.MY
MZMY
W Z.MY
MZMY

sz.2B

sz.3B

W Z.MY
MZMY

sz.4B

W Z.MY

MYMZ2
W Z.MZ

FZMZ1
A Mz
FZMZ1
A Mz
FZMZ1
A Mz
FZMZ1

W Z.MZ

MXMZ1

W y.MZ
MXMZ1

W Z.MZ
MYMZ1
W Z.MZ
MYMZ1

W y.MZ
MXMZ1

W Z.MZ
MYMZ1

W y.MZ

2Tf.MZ BMZ

t xy.1.2.3.4.B.

W Z.MZ

FXMZ1
2Tf.MZ BMZ

FYMZ2
2.Tf.Mz HMZ

MZMZ2

FYMZ1
2.Tf.Mz HMZ

HMZ2 Tf.MZ2 BMZ Tf.MZ

MZMZ1

HMZ2 Tf.MZ1 BMZ Tf.MZ

MYMZ2
W Z.MZ

t xz.2.4.

FXMY
2Tf.MY BMY

MYMY

HMY Tf.MY BMY TfMY

FZMY
HMY tw.MY

MYMZ2
W Z.MZ

syz.1.2.

Continuous deck beam - x-dir

Incoming beam - column

Section
HMY
BMY
Tf-MY
Tw-MY
a
A MY
Wy-MY
Wz-MY

Section
HMX
BMX
Tf-MX
Tw-MX
A MX
Wx-MX
Wy-MX
Wz-MX

HE800B
800
300
33
17.5
3.26E+04
4.86E+05
8.73E+06
9.92E+05

Section
HMZ
BMZ
Tf-MZ
Tw-MZ
A MZ
Wx-MZ
Wy-MZ
Wz-MZ

Fy
(kN)

Fz
(kN)
-321
-307
1304
-2619
1943

mm
mm
mm
mm
mm2
mm3
mm3
mm3

MYMZ1

W y.MZ

MYMZ2

Incoming beam - y-dir

mm
mm
mm (2)
mm (1)
mm
mm2
mm3
mm3

MXMZ1

FXMZ2

t xy.1.2.3.4.T.

syz.3.4.

I1252035
1200
500
35
20
5.0
5.76E+04
2.38E+07
2.92E+06

A Mz

B040440
400
400
40
40
5.76E+04
1.04E+07
6.30E+06
6.30E+06

FYMX2
2Tw.MY BMX
FYMX1
2Tw.MX BMX

MXMX2

HMX Tf.MX BMX Tf.MX

HMX Tf.MX BMY Tf.MX

MXMX2

FZMX2
HMX twMX
FZMX1
HMX tw.MX

mm
mm
mm (2)
mm (2)
mm2
mm3
mm3
mm3

Note (1):
Weld at w eb is assumed to carry shear only
Note (2):
Part pen w eld

Member
MX454020
MX504020
MY502020
MZ504010
MZ504020

LoadC

SctNam

2
2
2
2
2

HE800B
HE800B
I1252035
B040440
B040440

Fx
(kN)
504
-504
0
5
-3

1
1
40
339
-407

Mx
(kNm)
1
1
-2755
1311
1436

My
(kNm)
-670
690
0
-14
-8

Mz
(kNm)
-2
2
0
0
0

Top flange
Hot spot sx-T
sy-T
(MPa) (MPa)
1
-61
2
-66
116
3
-59
4
-64
117

Bottom flange
sz-T
sx-B
sy-B
(MPa)
(MPa) (MPa)
-263
97
193
92 -115
-260
94
196
90 -115

sz-B
(MPa)
165
-251
161
-256

Shear stresses
Von-Mises
tyz
txz
txy-T sj-T sj-B
tfill
UF
(MPa)
(MPa) (MPa) (MPa) (MPa) (MPa)
22
13 242 150
1.07
22
54
13 253 317
23
13 330 147
23
54
13 253 319

Figure G-7 Local analysis Joint 504020, lift condition

110

Joint check - Lift - Master Module

Intermediate deck

INPUT
Node
J504030 MX1
Member
Section

MX2

MY

MZ1

MZ2

MX404030 MX504030 MY502030 MZ504020 MZ504030

HE800B HE800B I0852035 B040440 B040440

RESULTS
UFmax
Dim LC
1.07
2

Material properties
gm
1.15
fy
355 MPa

Equations:

sx.1T

sx.2T

sx.3T

sx.4T

FXMX2
A Mx

A Mx
FXMX1
A Mx

sx.2B

sx.4B

A Mx

FXMX1

sx.1B

sx.3B

FXMX2

A Mx
FXMX2
A Mx

FXMX1
A Mx
FXMX1
A Mx

W y.MX
MYMX2

FXMX2

MYMX2

W y.MX

MYMX1

MYMX1

W y.MX

MYMX2
W y.MX
MYMX2
W y.MX

MYMX1
W y.MX
MYMX1
W y.MX

sy.2T

W Z.MX
MZMX2

W y.MX

MZMX2

sy.4T

W Z.MX

MZMX1

sy.2B

W Z.MX
MZMX1

sy.4B

W Z.MX

MZMX2

sz.1T

FYMY
A MY
FYMY
A MY
FYMY
A MY
FYMY
A MY

sz.2T

sz.3T

sz.4T

W Z.MX

FZMZ2
A Mz
FZMZ2
A Mz

W Z.MX
MZMX1

A Mz

W Z.MX

MZMX1

FZMZ2

W Z.MX
MZMX2

FZMZ2
A Mz

MXMY
W y.MY
MXMZ2
W y.MY
MXMY
W y.MY
MXMY
W y.MY

MXMZ2
W y.MZ
MXMZ2
W y.MZ
MXMZ2
W y.MZ
MXMZ2
W y.MZ

MZMY

sz.1B

W Z.MY
MZMY
W Z.MY
MZMY

sz.2B

sz.3B

W Z.MY
MZMY

sz.4B

W Z.MY

MYMZ2
W Z.MZ

FZMZ1
A Mz
FZMZ1
A Mz
FZMZ1
A Mz
FZMZ1

W Z.MZ

W y.MZ
MXMZ1

W Z.MZ
MYMZ1
W Z.MZ
MYMZ1

W y.MZ
MXMZ1

W Z.MZ
MYMZ1

W y.MZ

W Z.MZ

FXMZ1
2Tf.MZ BMZ

FYMZ2
2.Tf.Mz HMZ

FYMZ1
2.Tf.Mz HMZ

MZMZ2

HMZ2 Tf.MZ2 BMZ Tf.MZ

MZMZ1

HMZ2 Tf.MZ1 BMZTf.MZ

MYMZ2
W Z.MZ

t xz.2.4.

FXMY
2Tf.MY BMY

MYMY

HMY Tf.MY BMYTfMY

FZMY
HMY tw.MY

MYMZ2
W Z.MZ

syz.1.2.

Continuous deck beam - x-dir

Incoming beam - column

Section
HMX
BMX
Tf-MX
Tw-MX
A MX
Wx-MX
Wy-MX
Wz-MX

Section
HMZ
BMZ
Tf-MZ
Tw-MZ
A MZ
Wx-MZ
Wy-MZ
Wz-MZ

mm
mm
mm
mm
mm2
mm3
mm3
mm3

MXMZ1

2Tf.MZ BMZ

t xy.1.2.3.4.B.

Section
HMY
BMY
Tf-MY
Tw-MY
a
A MY
Wy-MY
Wz-MY

mm
mm
mm (2)
mm (1)
mm
mm2
mm3
mm3

MYMZ1

W y.MZ

MYMZ2

Incoming beam - y-dir

HE800B
800
300
33
17.5
3.26E+04
4.86E+05
8.73E+06
9.92E+05

MXMZ1

FXMZ2

t xy.1.2.3.4.T.

syz.3.4.

I0852035
800
500
35
20
5.0
4.96E+04
1.44E+07
2.92E+06

A Mz

B040440
400
400
40
40
5.76E+04
1.04E+07
6.30E+06
6.30E+06

FYMX2
2Tw.MY BMX
FYMX1
2Tw.MX BMX

MXMX2

HMX Tf.MXBMXTf.MX

HMX Tf.MX BMY Tf.MX

MXMX2

FZMX2
HMX twMX
FZMX1
HMX tw.MX

mm
mm
mm (2)
mm (2)
mm2
mm3
mm3
mm3

Note (1):
Weld at w eb is assumed to carry shear only
Note (2):
Part pen w eld

Member
MX404030
MX504030
MY502030
MZ504020
MZ504030

LoadC

SctNam

2
2
2
2
2

HE800B
HE800B
I0852035
B040440
B040440

Fx
(kN)

Fy
(kN)
-31
25
0
3
3

Fz
(kN)

0
0
-24
407
-378

54
56
754
-1787
925

Mx
(kNm)
-1
-1
-2490
1289
1209

My
(kNm)
-179
176
0
-9
11

Mz
(kNm)
0
0
0
0
0

Top flange
Hot spot sx-T
sy-T
(MPa) (MPa)
1
-21
2
-21
172
3
-22
4
-21
172

Bottom flange
sz-T
sx-B
sy-B
(MPa)
(MPa) (MPa)
-206
19
178
20 -173
-210
19
174
20 -173

sz-B
(MPa)
175
-234
172
-237

Shear stresses
Von-Mises
tyz
txz
txy-T sj-T sj-B tfill
UF
(MPa)
(MPa) (MPa) (MPa) (MPa) (MPa)
4
12 198 168
1.07
4
47
12 213 244
4
12 331 165
4
47
12 212 247

Figure G-8 Local analysis Joint 501030, lift condition

111