TA7291P
TA7291P
TA7291P,TA7291S,TA7291F
BRIDGE DRIVER
The TA7291P / S / F are Bridge Driver with output voltage control.
FEATURES
l 4 modes available (CW / CCW / STOP / BRAKE) l Output current: P type 1.0 A (AVE.) 2.0 A (PEAK) S / F type 0.4 A (AVE.) 1.2 A (PEAK) l Wide range of operating voltage: VCC (opr.) = 4.5~20 V VS (opr.) = 0~20 V Vref (opr.) = 0~20 V l Build in thermal shutdown, over current protector and punch = through current restriction circuit. l Standby mode available (STOP MODE) l Hysteresis for all inputs.
Weight HSIP10P2.54 : 2.47 g (Typ.) SIP9P2.54A : 0.92 g (Typ.) HSOP16P3001.00 : 0.50 g (Typ.)
2001-08-27
TA7291P/S/F
BLOCK DIAGRAM
PIN FUNCTION
P 7 8 4 1 5 6 2 10 PIN No. S 2 6 8 5 9 1 7 3 F 11 15 5 1 7 9 4 13 SYMBOL VCC VS Vref GND IN1 IN2 OUT1 OUT2 FUNCTION DESCRIPTION Supply voltage terminal for Logic Supply voltage terminal for Motor driver Supply voltage terminal for control GND terminal Input terminal Input terminal Output terminal Output terminal
P Type: Pin (3), (9): NC S Type: PIN (4): NC F Type: PIN (2), (3), (6), (8), (10), (12), (14), and (16): NC For F Type, We recommend FIN to be connected to the GND.
2001-08-27
TA7291P/S/F
FUNCTION
INPUT IN1 0 1 0 1 IN2 0 0 1 1 OUT1 H L L OUTPUT OUT2 L H L MODE STOP CW / CCW CCW / CW BRAKE
: Note:
IO (AVE.)
Note 1: Tc = 25C (TA7291P) Note 2: No heat sink Note 3: PCB (60 30 1.6 mm, occupied copper area in excess of 50%) Mounting Condition. Wide range of operating voltage: VCC (opr.) = 4.5~20 V VS (opr.) = 0~20 V Vref (opr.) = 0~20 V Vref VS
2001-08-27
TA7291P/S/F
ELECTRICAL CHARACTERISTICS
(Unless otherwise specified, Ta = 25C, VCC = 12 V, VS = 18 V)
CHARACTERISTIC SYMBOL ICC1 Supply Current ICC2 ICC3 Input Operating Voltage Input Current Input Hysteresis Voltage Upper Side Lower Side Upper Side Lower Side Upper Side P Type Lower Side 1 (High) 2 (Low) VIN1 VIN2 IIN V T VSAT U1 VSAT L1 VSAT U2 3 VSAT L2 VSAT U3 VSAT L3 2 1 TEST CIR CUIT TEST CONDITION Output OFF, CW / CCW mode Output OFF, Stop mode Output OFF, Brake mode Tj = 25C VIN = 3.5 V, Sink mode Vref = VS, VOUT VS measure IO = 0.2 A, CW / CCW mode Vref = VS, VOUT GND measure IO = 0.2 A, CW / CCW mode Vref = VS, VOUT VS measure IO = 0.4 A, CW / CCW mode Vref = VS, VOUT GND measure IO = 0.4 A, CW / CCW mode Vref = VS, VOUT VS measure IO = 1.0 A, CW / CCW mode Vref = VS, VOUT GND measure IO = 1.0 A, CW / CCW mode Vref = 10 V VOUT GND measure, IO = 0.2 A, CW / CCW mode Vref = 10 V VOUT GND measure, IO = 0.4 A, CW / CCW mode Vref = 10 V VOUT GND measure, IO = 0.5 A, CW / CCW mode Vref = 10 V VOUT GND measure, IO = 1.0 A, CW / CCW mode VL = 25 V 4 IL L V F U 1 VF U2 5 VF L1 VF L2 Iref 2 IF = 0.4 A IF = 1 A Vref = 10 V, Source mode 0.9 1.2 20 40 A VL = 25 V IF = 0.4 A IF = 1 A 1.5 2.5 50 V MIN 3.5 GND TYP. 8.0 0 6.5 3 0.7 0.9 MAX 13.0 50 10.0 5.5 0.8 10 1.2 UNIT mA A mA V A V
P/S/F Type
0.8
1.2
1.0
1.35 V
Saturation Voltage
S/F Type
0.9
1.35
1.3
1.8
1.2
1.85
VSAT U1 S / F Type Output Voltage (Upper Side) P Type VSAT U4 Upper Side Lower Side S/F Type Diode Forward Voltage P Type S/F Type P Type Reference Current Upper Side Lower Side Upper Side Lower Side IL U VSAT U2 3 VSAT U3
11.2
10.4
10.9
12.2 V
11.0
10.2
10.7
12.0
50 A
Leakage Current
2001-08-27
TA7291P/S/F
TEST CIRCUIT 1
ICC1, ICC2, ICC3
Note:
TEST CIRCUIT 2
VIN 1, VIN 2, IIN , VT, Iref
Note:
2001-08-27
TA7291P/S/F
TEST CIRCUIT 3
VSAT U1, 2, 3 VSAT L1, 2, 3 VSAT U1, 2, 3, 4
Note: Note:
IOUT calibration is required to adjust specified values of test conditions by RL. (IOUT = 0.2 A / 0.4 A / 0.5 A / 1.0 A) HEAT FIN of TA7291F is connected to GND.
TEST CIRCUIT 4
IL U, L
Note:
TEST CIRCUIT 5
VF U1, 2 VF L1, 2
2001-08-27
TA7291P/S/F
2001-08-27
TA7291P/S/F
2001-08-27
TA7291P/S/F
NOTES
Input circuit
Input Terminals of pin (5) and (6) (TA7291P) are all high active type and have a hysteresis of 0.7 V (typ.), 3 A (typ.) of source mode input current is required.
Output circuit
Output voltage is controlled by Vref voltage. Relationship between VOUT and Vref is VOUT = VBE ( 0.7) + Vref Vref terminal required to connect to VS terminal for stable operation in case of no requirement of VOUT control. Vref VS
2001-08-27
TA7291P/S/F
APPLICATION CIRCUIT
Note 1: Experiment to find the optimum capacitor valve. Note 2: To protect against excess current, current limitation resistor R should be inserted where necessary.
NOTES
l Be careful when switching the input because rush current may occur. When switching, stop mode should be entered or current limitation resister R should be inserted. l The IC functions cannot be guaranteed when turning power on of off. Before using the IC for application, check that there are no problems. l Utmost care is necessary in the design of the output line, VS, VCC and GND line since IC may be destroyed due to shortcircuit between outputs, air contamination fault, or fault by improper grounding.
10
2001-08-27
TA7291P/S/F
PACKAGE DIMENSIONS
HSIP10P2.54 Unit: mm
11
2001-08-27
TA7291P/S/F
PACKAGE DIMENSIONS
SIP9P2.54A Unit: mm
12
2001-08-27
TA7291P/S/F
PACKAGE DIMENSIONS
HSOP16P3001.00 Unit: mm
13
2001-08-27
TA7291P/S/F
000707EBA
TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the Handling Guide for Semiconductor Devices, or TOSHIBA Semiconductor Reliability Handbook etc.. The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (Unintended Usage). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customers own risk. The products described in this document are subject to the foreign exchange and foreign trade laws. The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. The information contained herein is subject to change without notice.
14
2001-08-27
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.