ATC 1000 Manual

Model ATC-1000 TCP/IP to RS232/422/485 Converter User s Manual
3.1 RS-232 PinoutDB9 Male DB9Male PIN2 PIN3 PIN5 PIN7 PIN8 Signal RXD TXD GND RTS CTS I/O IN OUT OUT IN
3.6 Connection Diagram RS-232 Connection
1.0 Introduction The ATC-1000 is a cost effective and highly integrated Serial-to-Ethernet Converter. Embedding a 8051CPU, 64KB OTP ROM, 32K bytes SRAM, 10/100Mbps Ethernet and serial port support handshake RTS, CTS. ATC-1000 Can control 1 x RS232/422/485 devices located virtually anywhere (via Ethernet or Internet). Automatically finds devices in the network Configuration over Driver Panels, serial Port,WEB Browser, SNMP Automatic mode switching between Driver and RAW mode Support TCP/IP, UDP, DHCP, 3.3 Connect to 10/100M ATC-1000 10/100/M Port connect to switcher or HUB use straight-Through Cable 3.2 RS-422/485 Pinoutsix Terminal from left Terminal No RS-422 RS-485 1 T+ 485+ 2 T4853 R+ 4 R5 VIN VIN 6 GND GND RS-422 Connection
2.0 Features: 3-in-1 RS-232/422/485 interface Max.230Kbps Serial interface and 10/100 Mbps Ethernet Supports 4- and 2-wire RS-485 with AUTO-SEND and built-in terminator Supports industrial 24 VDC power input and optional Power over Serial Terminal block accessories for easy RS-422/485 serial wiring Supports IP configuration by MAC address Supports configuration store and copy for easy deployment Supports Driver, TCP Server/Client, UDP Server/Client, Pair Connection operation modes Easy and powerful configuration program Approval CE, RoHS 3.0 . Hardware Installation & Initial Setup PWR ACT 3.4 Power Supply ATC-1000 TCP/IP converter can adopt the products 9V power adapter for power supply or adopt power from other DC power or device.(+9--+24V@500-100mA) 3.5 ATC-1000 LED indication LINK Indication Ethernet LinkGreen on Ethernet Link established Data Sending/Receiving between Serial and the Ethernet Indication Power
RS-485 Connection
4.0 Configuration and Operation Use this section to set up your computer to assign it a static IP address in the 192.168.2.2 to 192.168.2.254 range with a subnet mask of 255.255.255.0. This is necessary to ensure that your computer can communicate with your ATC-1000. Your
computer must have an Ethernet card and TCP/IP installed. TCP/IP should already be installed on computer using Windows 98/2000/XP and later operating systems. Step 1Open your web browser and type http://192.168.2.1 in the browsers address box. This address is the factory set IP Address of your ATC-1000. Press Enter. Step 2The ID and Password required prompt box will appear. Typing admin (default username) in the ID field and typing system (default password) in the Password field. Click OK. The setup screen will then appear.
All above the functions explain as below: 4.3 Administrator Setup Manager of the relevant setting page. 4.4 Authentication Configuration The Users can change the username and password to prevent unauthorized access. Login ID and password authentication, the maximum is 15 characters and numbers. User Name: default admin Password: default system
Subnet mask: default 255.255.255.0 Gateway: default 192.168.2.254 Primary DNS: default 192.168.2.253 If you are connecting through a static or fixed IP from your network environment, perform these steps Step 1: Enter IP address Step 2: Enter Subnet mask Step 3: Enter Gateway IP address Step 4: Enter Primary DNS IP address Step 5: click Update button 4.6 DHCP
Host Name (Optional): default NETUART , maximum length 15 characters If there is a DHCP Server existing in your network environment or you subscribe a CABLE service from your ISP, you can set IP configuration to DHCP to get a dynamic IP address. The Host Name is an optional item,
4.5 System IP Configuration The ATC-1000 support three IP connection types: Static IP, User login to enter a password. Default ID : admin DHCP. These types are listed in the Web page for the IP Configuration setting. Each setup screen and available features will differ depending on what kind of IP connection types you select. Default is Static IP
depending on your DHCP Server setting.

5.0 System Status This screen shows the ATC-1000s current status. All of the information provided is read-only. Kernel Version: the installed version of the kernel.
Default Password: system 4.2 The menu features as below:
MAC Address: At present the device MAC Address Nickname: the product model name of NetUART
5.0 Load default setting Allow Users to reset the ATC-1000 to return the initial value, but Static (or Fixed) IP IP Address: default 192.168.2.1 the MAC Address will not be updated.
If your device is acted as passive to accept commands from remote and the data be guaranteed to be received
5.1 Operation mode
by peer is not your concern, then you can set ATC-1000 as UDP Server. Be sure the value of item Local Port Number is same as your remote control application using.
5.5 UDP Client Remote Connection Port Number: default 21, range 0 to 65535 Remote Host IP Address: default 192.168.2.2
The ATC-1000 support four operation mode: TCP Server, TCP Client, UDP Server and UDP Client. These modes are listed in the Web page for the Operation Mode setting. Each setup screen and available features will differ depending on what kind of operation mode you select. Default is TCP Server. 5.2 TCP Server
Port Number: default 23, range 0 to 65535 If your device is acted as passive to accept commands from remote and the data be guaranteed to be received by peer is your concern, then you can set ATC-1000 as TCP Server. Be sure the value of item Port Number is same as your remote control application using.
If your device is acted as active to report real-time status to remote and the data be guaranteed to be received by peer is not your concern, then you can set ATC-1000 as TCP Client. Be sure the value of item Remote Connection Port Number is same as your remote control application using and set the correct value of Remote Host IP Address.
Client mode inactive timeout (minutes): default 20

( 0=Disable) If you want to keep the connection between ATC-1000 and your remote control application always on, then set the value of item
Client mode inactive timeout (minutes) to 0, otherwise,

when the inactive time of no any traffic on line reach the setting value, ATC-1000 will terminate this connection. 5.3 TCP Client Remote Connection Port Number: default 23, range 0 to 65535 Remote Host IP Address: default 210.200.181.102 If your device is acted as active to report real-time status to remote and the data be guaranteed to be received by peer is your concern, then you can set ATC-1000 as TCP Client. Be sure the value of item Remote Connection Port Number is same as your remote control application using and set the correct value of Remote Host IP Address. 5.4 UDP Server
6.0 UART Control (RS-232)

The ATC-1000 support three serial types: RS232, RS422 and RS485, The user can reference hardware diagram to directly select RS232, RS422, RS485, no need select by software. Baud Rate: default 57600, range 300bps to 230.4Kbps
Character Bits: 5, 6, 7, 8 (default)

Parity Check: None (default), even, odd, space, mark Stop Bits: 1 (default), 1.5 or 2
Hardware Flow Control: None (default), CTS/RTS (or Hardware)
Local Port Number: default 21, range 0 to 65535

ATC 1000 Manual

Uploaded by

Copyright:

Available Formats

ATC 1000 Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ATC 1000 Manual

Uploaded by

Copyright:

Available Formats

Model ATC-1000 TCP/IP to RS232/422/485 Converter User s Manual

3.6 Connection Diagram RS-232 Connection

depending on your DHCP Server setting.

Default Password: system 4.2 The menu features as below:

Client mode inactive timeout (minutes): default 20

Client mode inactive timeout (minutes) to 0, otherwise,

6.0 UART Control (RS-232)

Character Bits: 5, 6, 7, 8 (default)

Hardware Flow Control: None (default), CTS/RTS (or Hardware)

Local Port Number: default 21, range 0 to 65535

You might also like