IS 613:2000

Indian Standard COPPER RODS AND BARS FOR ELECTRICAL PURPOSES - SPECIFICATION ( Third Revision )

ICS 77.150.3b

0 BIS 2000

BUREAU
MANAK

OF
BHAVAN,

INDIAN

STANDARDS
ZAFAR MARG

9 BAHADUR SHAH NEW DELHI 110002

Jutle 2000

Price Group 4

Copper and Copper Alloys Sectional

Committee,

MTD 8

FOREWORD This Indian Standard (Third Revision) was adopted by the Bureau of Indian Standards, after the draft finalized by the Copper and Copper Alloys Sectional Committee had been approved by the Metallurgical Engineering Division Council. This standard was first published in 1954 and subsequently following modifications have been made: a) Straightness revised in 1964 and 1984. In this revision / the

value of 3 mm for every 1 000 mm has been added. bending has been deleted. and now given in detail. values specified as 70 to 90 HV. and hard temper condition and hexagonal have been modified.

b) Clause on edgewise

c) Radius on edges have been modified d) In half-hard condition, e) Reference f) Conductivity g) Dimensions hardness

of cathode copper has been deleted. and resistivity and tolerances values for half-hard for round, square, rectangular has been modified. rods/bars have been included.

h) Table on mechanical

properties

j) Clause on bend test has been added. For the purpose of deciding~whether observed or calculated, expressing IS 2 : 1960 Rules for rounding off the rounded off value should be the a particular requirement of this standard the result of a test or analysis, shall be numerical values (revised). The number same as that of the specified value in this is complied with the final value, rounded off in accordance with of significant places retained in standard.

IS 613 : 2000

Zndian Standard COPPER RODS AND BARS FOR ELECTRICAL PURPOSES - SPECIFICATION ( Third Revision )
1 SCOPE This standard covers the requirements and bars for electrical purposes. 2 REFERENCES 5 PHYSICAL CONSTANTS 5.1 The constants given in Annex A are based on standards fixed by the International Electrotechnical Commission. 5.2 Coefficient of Linear Expansion for copper rods 4.2 Minimum Cross-Sectional Dimension The diameter in the case of rounds, width across flats in the case of square and hexagonal shapes, the smaller side width in the case of rectangular rods.

The following Indian Standards contain provisions which through reference in this text, constitute provision of this standard. At the time of publication, the editions indicated were valid. All standards are subject to revision and parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below: IS No. 191 : 1980 (Part 5) : 1980 (Part 6) : 1980 440 : 1964 1387 : 1993
Title

The coefficient of linear-expansion of annealed or harddrawn high-conductivity copper over a range of 0 to 150C shall be taken as 0.000 017/C. 5.3 Mass At a temperature of 2OC, the density of highconductivity copper shall be taken as 8.89 g/cm3. 5.4 Resistance of a Solid Conductor

Copper: Electrolytic tough pitch copper (ETP) (third revision) Fire refined high conductivity copper (FRHC) (third revision) Methods of chemical analysis of copper (revised) General requirements for the supply of metallurgical materials (second
revision)

1599 : 1985 1608 : 1995

Methods
revision)

for bend

test (second

-5.4.1 For the purpose of calculation, the resistance at 20C of a solid conductor of annealed highconductivity copper, one metre in length and of a uniform cross-sectional area of one square millimetre has been taken as 0.017 241 ohm.
NOTE Copper which at 20C has a resistivity of l/58 = (0.017 241...) ohm mm/m is said to have a conductivity of 100 percent 1AC.S.

Mechanical testing of metals Tensile testing (second revision) Methods of sampling non-ferrous 1817 : 1981 metals for chemical analysis Glossary of terms for copper and 3288 copper alloys: (Part I) : 1986 Materials (third revision) (Part 3) : 1986 Wrought forms Methods of test for resistance of 3635 : 1966 metallic electrical resistance material 3 SUPPLY OF MATERIAL

5.4.2 The resistance of hard-drawn high-conductivity copper is a function of its hardness, and the tensile strength is an approximate indication of the degree of hardness. Within a range from 305 to 460 MPa tensile strength, the following formula has been found to express sufficiently close to the results in practice, and has been adopted in calculating the resistance of harddrawn copper given in this standard : P=-& where P = percentage increase in resistivity of the hard-drawn copper wire over its resistivity -when annealed, and
= tensile

General requirements relating to the supply of material shall conform to IS 1387. 4 TERMINOLOGY 4.1 For the purpose of this standard, the definition of terms given in IS 3288 (Parts 1 and 3) and the following shall apply.

strength of the hard-drawn wire in MPa. of the resistances

copper

For the determination

of hard-drawn

IS 613 : 2000 high-conductivity copper by the formula given above, the resistance of annealed high-conductivity copper at 20C as given under 5.4.1 has been taken as basis. 5.5 Constant Resistance Mass Temperature Coefficient of following 0 conditions Annealed Half-hard Hard COMPOSITION as specified by the purchaser:

HB HD -

8 CHEMICAL

5.5.1 At a temperature of 2oC, the coefficient of variation of the resistance with temperature of annealed high-conductivity copper measur&between two potential points rigidly fixed to the wire has been taken as 0.003 931C. 5.5.2 At a temperature of 2OC, the coefficient of variation of the resistance with temperature of harddrawn high-conductivity copper measured between two potential points dgidly fixed to the wire has been taken as 0.003 81/V, which is an average value for copper of 97 percent conductivity.
NOTE - Copper which at 20C has a resistivity of 1158 = (0.017 241....) ohm mmlm is said to have a conductivity of 100 percent IACS.

8.1 The material shall have chemical composition as given in for grades ETP, FRHC of IS 191 (Part 5) or IS 191 (Part 6) respectively. 8.2 The chemical composition shall be determined either by the method specified in IS 440 or any other established instrumental/chemical method. In case of dispute the procedure specified in the latest version of IS 440 for chemical analysis, shall be the referee method. However when the method is not given in IS 440 the referee method shall be as agreed to between the purchaser and the manufacturer. 9 MECHANICAL Test PROPERTIES

9.1 Tensile 6 FREEDOM FROM DEFECTS The rods and bars shall be bright and clean. It shall be free from blisters, slivers, scale, fins, spills, cracks and other defects. 7 CONDITION The material OF~SUPPLY shall be supplied in any one of the

The material when tested for tensile test and hardness in accordance with IS 1608 and IS 1501 (Parts 1 and 2) shall have the properties as given in Table 1. 9.1.1 Rods/Bars Other than Rectangular

For material over 30 mm diameter, thickness or width across flats, the test piece shall be turned with its centre

Table 1 Mechanical

Properties

(Clause 9.1)
Diameter, Width Across Flats or Thickness
r

Condition

Tensile Strength

Elongation

on 5.65 ,&

of Gauge Length
.
h , \

Hardness (for all Shanes)

*
Over Upto and Including (2) 10 12 50 90

Round MPa

(1) 6 10 12 50 Over 90 6 10 12 25 50 Over 90 6 10 12

(3) 250 Max 240 Mm 230 MUX 230 Mar * 280 Min

Square and hexagonal MPa (4) 240 Max 230 Mar 230 Mar * 260 250 230 230 Min Min Min Min *

Rectangular MPa (5) 240 MUX 230 Mm * 250 Min 230 Min 230 Min * 270 Min 260 Min 250 Min *

Round Percent (6) 32Min 40 Min 45 Min 45 Min * 8 Min 12 Min 18 Min 22 Min 22 Min *

Square and Hexagonal Percent (7) 40 Min 45 Min 45 Min * 12Min 18 Min 22 Min 22 Min *

Rectangular Percent (8) 40 Min 45 Min * 12 Min l8Min 18 Min * -

(9)

+ ~OMUX

10 12 25 50 90 10 12 25 HD HB

260 250 230 230

Min Min Min Min *

70 to 90

330 Min 320 Min 290 Min 260 Min *

310 Min 280 Min 250 Min *

6 Mire 8 Min 12 Min *

6 Min 8 Min 12 Min *

8 Min 8 Min IOMin *

90 Min

90 25 Over 90 * As agreed to between the purchaser

and the manufacturg.

IS 613 : JO00 For-material of smaller diameter or width which may not be~tested in the condition as manufacture of the test piece shall be turned from the centre of the material. 9.1.2
Rectangular Bars/Rods 14.0 mm from the surface of the material.

11.1.1

Direct Measurement

on the Test Sample

Resistance measurements shall be determined con specimens of the rod after cleaning, but without further processing and annealing. If direct measurement of electrical resistivity is not possible on the sample as received condition due to higher sample size, alternatively, method of measuring electrical conductivity in percent IACS, employing eddy current probe may be applied in place of electrical resistivity and the electrical conductivity values as obtained, must comply with the values given in Table 2 (see 11.2). 11.1.2 Measurement
on Test Sample After Annealing

The test piece shall be taken from the centre of the rod/bar. 9.2 Bend Test The material shall be tested for bend test in accordance with IS 1599, if agreed to between the purchaser and the manufacturer. 10 DIMENSIONS AND TOLERANCES

10.1 The dimensions and tolerances for round, square, rectangular and hexagonal rods/bars shall be given in Table 2. 10.2 The tolerance on length of bar or rod, if ordered in exact length,-shall be within the limits specified in Table 3. 10.3 The straightness and/or edgewise curvature shall not exceed 3 mm for every 1 000 mm. 10.4 Radius Material) on Edges (Square and ~Rectangular

Resistance measurement shall be made on specimens of the rod after cleaning and processing down to a diameter of approximately 2.0 mm and annealing at temperature 500C for 30 minutes. Other equivalent annealing method may be used. Test specimens processed to a diameter other than 2 mm may be used if so specified. 11.2 The electrical resistivity when tested in accordance with IS 3635 shall comply with the value given in Table 5. 12 SAMPLING CONFORMITY 12.1 Lot In any consignment all the copper rods/bars of the same grade (chemical composition), size, temper and manufactured by a single firm under essentially similar conditions of production shall be grouped together to constitute a lot. AND CRITERIA FOR

If the material is required with radiused edges, the radius of curvature shall be as given in Table 4. 11 ELECTRICAL RESISTIVITY TEST

11.1 The electrical resistivity shall be measured under one of the conditions given in 11.1.1 or 11.1.2.

Table 2 Dimensions
(Clauses

and Tolerances 11.1.1)

10.1 a&

All dimensions in millimetres.

Specified Diameter, Width Across Flats or Thickness (c / % Over Up to and Including (1) 6 10 12 25 50 80 100 160 (2) 10 12 25 50 80 100 160 300

Tolerance / Round (Diameter)

(Plus or Minus) . Rectangular Bar (Width or Thickness) (5) 0.07 0.10 0.14 0.25 * *

Square and Hexagonal Rod (Width Across Flat) (4) 0.08 0.10 0.16 0.25 * * *

(3) 0.05 0.05 0.08 0.12 0.18 * * *

* As agreed to between the purchaser and the manufacturer.

IS 613 : 2000 Table 3 Tolerances on Length of Bar Rod in Straight Length (ClUUSP 10.2)
All dimensions Length of Bar/Rod Observed in Exact Length Y Over (1) 150 Up to and Including (2) 150 1 200 -2 400 (3) 1.2 1.5 2.5 5.0 (1) (2) 5 13 20 32 50 80 300 500 (3) 0 1 2 3 5 7 A in millimetres. Tolerance (Plus or Minus)

characteristics shall be considered as defective. If the number of defectives found is less than or equal to the permissible number of defectives given in co1 3 of Table 6, the lot shall be considered as confirming to the requirements of these characteristics. Table 6 Scale of Sampling and Permissible Number of Defectives (Clauses
No. of Bars/ Rods in a Lot

12.1.1, 12.2.1 and 12.2.2)

Permissible No. of Defectives No. of Bars/ Rods for Copper Content, Tensile Test and Electrical Test (4) 2 3 4 5 6 7

No. of Bars/ Rods in the Sample

I 200
2 400

Table 4 Corner

Radius

and Tolerances

up

to 100

(Clause
All dimensions Thickness h ~ Over Up to and Including (1) 6 25 50 (2) 25 50 -

10.4)
in miliimetres. Tolerance (Plus or Minus)

101 to 301 to

501 to 1 000 Corner Radius 1001 to3000 3001andabove

(31 2.5 3.2 *

(4) 0.25 0.25 and the manufacturer.

* As agreed to between the purchaser

Table 5 Electrical (Clause

Condition

Resistivity 11.2)

12.2.2 From each lot the number of rods/bars to be subjected for the determination of copper content (see S), tensile test (see 9.1) and electrical resistivity test (see 11) shall be in accordance with co1 1 and 4 of Table 6. One determination of all other requirements of chemical composition (see 8) shall be done for each lot irrespective of the size of the lot. The bars/rods for these tests shall be selected out of those obtained in 12.1.1.
NOTE-The material required for chemical analysis from each of the rods intended for testing shall be collected in accordance with IS 1817.

Measured by the Resistivity Conductivity Method Given ohm mm*/m WCS) in Clauses at 20C Max Percent, Min (2) 11.1.1 or 11.1.2 (3) 0.017 37 0.017 77 (4) 99.25 97.0

(1) Annealed Half-hard Hard and

11.1.1 or 11.1.2

NOTE-The constant for converting the resistance at various temperature to the resistance at standard temperature of 20C and reciprocals these constants for converting resistance at 20C to resistance at other temperature for annealed and hard-drawn highconductivity copper are given in Annex B.

12.2.2.1 In the case of determination of copper content, tensile test and electrical resistivity test, the lot shall be considered as conforming to the requirements of this standard if all the test results on different samples satisfy the corresponding requirements. 12.2.2.2 The lot shall be declared as conforming to the requirement of other constituents if the-single test result of chemical analysis obtained for each constituent satisfy the corresponding requirement of the standard. 12.3 Retest 12.3.1 If the test results of chemical analysis fails to satisfy the requirements for any of the constituents, two more tests for that constituent shall be done on the same sample in order to confirm~that the analysis has been done properly. If both the test results satisfy the relevant requirements, the lot sl*all be considered as confirming to the this standard, cltherwise not. 4

12.1.1 Tests for determining the conformity of the lot to the requirements of this standard shall be carried out on each lot separately. The number of bars/rods to be selected for this purpose at random over the whole lot shall be in accordance with co1 1 and 2 of Table 6. 12.2 Number of Tests and Criteria for Conformity

12.2.1 The rods/bars selected in accordance with co1 1 and 2 of Table 6 shall be inspected for freedom from defects (see 6) and dimensions (see 8). Any rod/bar failing to meet the requirement of one or more of these

IS 613:2000

12.3.2 If the test results on any sample for tensile test and electrical resistivity test, fail to satisfy the requirements for any of the mechanical~properties and electrical resistivity, two more tests shall be done on the sample selected from the same lot. If both the test results satisfy the relevant requirements the lot shall be considered as conforming to this standard, otherwise not.
13 PACKING

lot number, date of manufacture and any Information required by the purchaser. 14.1.1 The material Standard Mark. may also be marked

such

with the

The material shall be packed in bundles, boxes, cases or crates so as to ensure the safe transporation of the material and avoid damage in transit. 14 MARKING

14.1.2 The use of Standard Mark is governed by the provision of the Bureau of Indian Standards Act, 1986 and the Rules and Regulations made there under. The details of the conditions under which the licence for the use of Standard Mark may be granted to manufacturers or producers may be obtained from the Bureau of Indian -Standards.

15 INFORMATION PURCHASER

TO BE GIVEN

BY THE

14.1 Each package tagged with suitable metal tag shall bear the marking made on them with the grade of material, name of the manufacturer, the mass, size,

This standard contains a number of clauses in which the purchaser is allowed to exercise an option. The list of information to be given by the purchaser in respect of these clauses is given in Annex C.

ANNEX A (Chse
INTERNATIONAL A-l STANDARD VALUES STANDARD

5.1)
HIGH-CONDUCTIVITY COPPER

FOR ANNEALED

A-1.0 The following values fixed by the International Electrotechnical Commission for Standard Annealed Copper have been taken as standard values for annealed high-conductivity copper. A-l.1 At a temperature of 20C the volume resistivity of standard annealed copper is l/58 (or 0.0 17 241,,,....)ohrn mm2/m. A-l.2 At a temperature of 20C the density of standard annealed copper is 8.89 g/cm3. A-l.3 At a temperature of 20C the coefficient linear expansion of standard annealed copper 0.000 017/C. of is

NOTE-The above value for the coefficient of linear expansion may be applied to annealed copper over a temperature range of 0 to 15oc.

A-l.4 At a temperature of 20C the coefficient of variation of resistance with temperature of standard annealed copper measure between two potential points rigidly fixed to the wire, the metal being allowed to expand freely, is 0.003 93 (or 254,i5....]10C. A-l.5 It fcillows from A-l.1 and A-l.2 that at a temperatureof 20C the mass resistivity of standard annealed 1 copper is 58 X 8.89 = 0.153 23 ohm g/m/m.

IS 613:2000

ANNEXB
(Table 5)
MULTIPLIER CONSTANTS AND THEIR RECIPROCALS AND HARD-DRAWN COPPER FOR ANNEALED

B-l The constants for converting resistance at various temperatures to the standards temperature of 20C and reciprocals of these constants for converting resistance at 20C to other temperatures for annealed copper of conductivity 100 percent IACS are given in Table 7. Table 7 Multiplier Constants and Their Reciprocals for Annealed Copper of Conductivity 100 Percent IACS (Clauw B-l)
Temperature C (1) 10 10.5 II 11.5 12 12.5 13 13.5 14 14.5 15 15.5 16 16.5 17 17.5 18 18.5 19 19.5 20 20.5 21 21.5 22 22.5 23 23.5 24 24.5 25 25.5 26 26.5 27 27.5 ~Multiplier Constant (2) 1.040 9 1.038 8 1.036 7 1.034 6 1.032 5 1.030 4 1.028 3 1.026 2 1.024 I 1.022 1 1.020 0 1.018 0 1.016 0 1.013 9 1.011 9 1.009 9 1.007 9 1.005 9 1.003 9 1.002 0 1.000 0 0.998 0 0.996 1 0.994 1 0.992 2 0.990 3 0.988 3 0.986 4 0.984 5 0.982 6 0.980 7 0.978 8 0.977 0 0.975 1 0.973 2 0.971 4 Reciprocal of Constant (3) 0.960 7 0.962 7 0.964 6 0.966 6 0.968 6 0.970 5 0.972 5 0.974 5 0.976 4 0.978 4 0.980 4 0.982 3 0.984 3 0.986 2 0.988 2 0.990 2 0.992 1 0.994 1 0.996 1 0.998 0 1.000 0 1.020 0 1.003 9 1.005 9 1.007 9 1.009 8 1.011 8 1.013 8 1.015 7 1.017 7 1.019 7 1.021 6 1.023 6 1.025 5 1.027 5 1.029 5

Table 7 (Continued)
(1)
28 28.5 29 29.5 30 30.5 31 31.5 32 32.5 33 33.5 34 34.5 35 35.5 36 36.5 37 37.5 38 38.5 39 39.5 40 40.5 41 41.5 42 42.5 43 43.5 44 44.5 45 45.5 46 46.5 47 47.5 48 48.5 49 49.5 50 50.5

(2)
0.969 5 0.967 7 0.965 8 0.964 0 0.962 2 0.960 4 0.958 6 0.956 8 0.955 0 0.953 2 0.951 4 0.949 6 0.947 8 0.946 1 0.944 3 0.942 6 0.940 8 0.939 1 0.937 4 0.935 7 0.933 9 0.932 2 0.930 5 0.928 8 0.927 1 0.925 4 0.923 8 0.922 1 0.920 4 0.918 8 0.917 1 0.915 5 0.913 8 0.912 2 0.910 5 0.908 9 0.907 3 oz905 7 0.904 1 0.902 5 0.900 9 0.899 3 0.897 7 0.896 1 0.894 5 0.893 0

(3) 1.031 4 1.033 4 1.035 4 1.037 3 1.039 3 1.041 3 1.043 2 1.045 2 1.047 2 1.049 I 1.051 1 1.053 1 1.055 0 1.057 0 1.059 0 1.060 9 1.062 9 1.064 8 1.066 8 1.068 8 1.070 7 1.072 7 1.074 7 1.076 6 1.078 6 1.080 6 1.082 5 1.084 5 1.086 5 1.088 4 1.090 4 1.092 4 1.094 3 1.096 3 1.098 3 1.100 2 1.102 2 1.104 1 1.106 1 1.108 1 1.110 0 1.112 0 1.114 0 1.115 9 1.117 9 1.119 9

IS 613 : 2000 Table 7 (Concluded)

(1)
51 51.5 52 52.5 53 53.5 54 54.5 55 55.5 56 56.5 51 57.5 58 58.5 59 59.5 60 60.5 61 61.5 62 62.5 63 63.5 64 64.5 65 65.5 66 66.5 67 67.5 68 68.5 69 69.5 70 NOTES 1 Given the resistance of a wire at TC, the resistance at 20C is found by multiplying the resistance at TC by the constant for TC given in co1 2. Conversely, given the resistance at 20C the coresponding resistance at TC is found by multiplying the resistance at 20C by the reciprocal of constant for TC given in co1 3. 2 The temperature coefftcient of resistance of copper varies slightly from sample to sample according to its exact conductivity. The figures given in this table are based on the international standard coefficient of 0.003 93PC at 20C. The error in using this table for copper within the range of conductivity of 99 to 101 percent will not exceed 0.06 percent.

(2)
0.891 0.889 0.888 0.886 0.885 0.883 0.882 0.880 0.x79 0.877 0.876 0.874 0.873 0.871 0.870 0.868 0.867 0.865 0.864 0.862 0.861 0.859 0.858 0.856 0.855 0.854 0.852 0.851 0.849 0.848 0.846 0.845 0.842 0.844 0.841 0.839 0.838 0.837 4 8 3 7 2 7 1 6 I 6 1 6 0 6 I 6 2 6 2 7 2 8 4 9 4 0 6 1 7 3 9 5 7 1 3 9 5 1

(3) 1.121 1.123 1.125 1.127 1.129 1.131 1.133 1.135 1.137 1.139 1.141 1.143 1.145 1.147 1.149 1.151 1.153 1.155 1.157 1.159 1.161 1.163 1.165 1.167 1.169 1.171 1.172 1.174 1.176 1.178 1.180 1.182 1.186 1.184 1.188 1.190 1.194 1.192 8 8 0 7 7 7 7 6 6 5 5 4 4 4 3 3 3 2 2 2 1 1 1 0 0 0 9 9 8 8 8 7 7 7 6 6 5 6

Table 8 Multiplier Constants and Reciprocals of Constants for Hard-Drawn Copper of Conductivity 97 Percent (Clause B-2)
Temperature C (1) 10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15 15.5 16 16.5 17 17.5 18 18.5 19 19.5 20 20.5 21 21.5 22 22.5 23 23.5 24 24.5 25 25.5 26 26.5 27 27.5 28 28.5 29 29.5 30 30.5 31 31.5 32 32.5 33 33.5 34 34.5 Multiplier Constant (2) 1.039 6 1.037 6 1.035 5 1.033 5 1.0314 1.029 4 1.027 4 I.025 4 1.023 4 1.021 4 1.019 4 1.017 4 1.015 5 1.013 5 1.011 6 1.009 6 1.007 7 1.005 7 1.003 8 1.001 9 1.000 0 0.998 1 0.996 2 0.994 3 0.992 4 0.990 6 0.988 7 0.986 8 0.985 0 0.983 1 0.981 3 0.979 5 0.977 7 0.975 8 0.974 0 0.972 2 0.970 4 0.968 6 0.966 8 0.965 1 0.963 3 0.961 5 0.959 8 0.958 0 0.956 3 0.954 5 0.952 8 0.951 1 0.949 4 0.947 6 Reciprocal Constant (3) 0.961 9 0.963 0.965 0.967 0.969 8 7 6 5 of

0.971 4 0.973 3 0.975 2 0.977 1 0.979 0 0.981 0 0.982 9 0.984 8 0.986 7 0.988 6 0.990 5 0.992 4 0.994 3 0.996 2 0.998 1 1.000 0 1.0019 1.003 8 1.005 7 1.007 6 1.009 5 1.011 4 1.013 3 1.015 2 1.017 1 1.019 1 1.021 0 1.022 9 1.024 8 1.026 7 1.028 6 1.030 5 1.032 4 1.034 3 1.036 2 1.038 1 1.040 0 1.0419 1.043 8 1.045 7 1.047 6 1.049 5 1.051 4 1.053 4 1.055 2

0.835 8

1.196 5

B-2 The constant for converting resistances at various temperatures to the standard temperature of 20C and reciprocals of these constants for converting resistances at 20C to other temperatures for hard-drawn copper of conductivity 97 percent are given in Table 8. 7

IS 613 : 2000 Table 8 (Conrinued) (1)

35 35.5 36 36.5 37 37.5 38 38.5 39 39.5 40 40.5 41 41.5 42 42.5 43 43.5 44 44.5 45 45.5 46 46.5 47 41.5 48 48.5 49 49.5 50 50.5 51 51.5 52 52.5 53 53.5 54 54.5 55

Table 8 (Concluded)
(3) 1.057 2 1.059 I 1.061 0 1.062 9 1.064 8 1.066 7 1.068 6 1.070 5 1.072 4 1.074 3 1.076 2 1.078 1 1.080 0 1.081 9 1.083 8 1.085 I 1.087 6 1.089 5 1.091 4 1.093 3 1.095 3 1.097 2 1.099 I 1.101 0 1.102 9 1.104 8 1.106 7 1.108 6 1.110 5 1.112 4 1.114 3 1.116 2 1.118 I 1.120 0 1.121 9 1.123 8 1.125 7 1.127 6 1.129 5 1.131 4 1.133 4 68 68.5 69 69.5 70 NOTES 1 Given the resistance of a wire at PC, the resistance at 2OC is found by multiplying the resistance at TC by the constant for TC given in co1 2. Conversely, given the resistance at 2OC, the corresponding resistance at TC is found by multiplying the resistance at 20C given in co1 3. 2 The temperature coefficient of resistanceof copper varies slightly from sample to sample according to its exact conductivity. The figures given in this table are based on a coefficient of 0.003 81PC at 20C which is an average value for copper of 97 percent conductivity. The error in using this table for copper within the range of conductivity of 96 to 98 percent will not exceed 0.06 percent. 0.845 4 0.844 0 0.842 I 0.841 3 0.840 0 1.182 9 1.184 8 1.186 I 1.188 6 1.190 5 64 64.5 65 65.5 66 66.5 67 67.5 0.856 4 0.855 0 0.853 6 0.852 3 0.850 9 0.849 5 0.848 1 0.846 8 1.167 6 1.169 5 1.171 5 1.173 4 1.175 3 1.177 2 1.179 1 1.181 0

(2)
0.945 9 0.944 2 0.942 5 0.940 9 0.939 2 0.937 5 0.935 8 0.934 2 0.932 5 0.930 8 0.929 2 0.927 6 0.925 9 0.924 3 0.922 I 0.921 0 0.919 4 0.917 8 0.916 2 0.914 6 0.913 0 0.911 4 0.909 9 0.908 3 0.906 7 0.905 2 0.903 6 0.902 1 0.900 5 0.899 0 0.897 4 0.895 9 0.894 4 0.892 8 0.891 3 0.889 8 0.888 3 0.886 8 0.885 3 0.883 8 0.882 3

(1)
55.5 56 56.5 57 51.5 58 58.5 59 59.5 60 60.5 61 61.5 62 62.5 63 63.5

(2)
0.880 9 0.879 4 0.877 9 0.876 4 0.875 0 0.873 5 0.872 1 0.870 6 0.869 2 0.867 8 0.866 3 0.864 9 0.863 5 0.862 1 0.860 6 0.859 2 0.857 8

(3) 1.135 3 1.137 2 IA39 1 l.I410 1.142 9 1.144 8 1.146 7 1.148 6 1.150 5 1.152 4 1.154 3 1.156 2 1.158 1 1.160 0 1.161 9 1.163 8 1.165 I

ANNEX C (Clause 15)

INFORMATION TO BE GIVEN BY THE PURCHASER C-l Whether the purchaser wishes to inspect material at the suppliers works (see 3). C-2 The chemical composition the C-3 Dimensional tolerances (see 10). (see 12).

grade required (see 8).

c-4 Sampling and criteria for conformity c _5 Marking details (see 14).

Bureau of Indian Standards BIS is a statutory institution established under the Bureau of Indian Standards Act, 1986 to promote harmonious development of the activities of standardization, marking and quality certification of goods and attending to connected matters in the country. Copyright BIS has the copyright of all its publications. No part of these publications may be reproduced in any form without the prior permission in writing of BIS. This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations. Enquiries relating to copyright be addressed to the Director (Publications), BIS. Review of Indian Standards Amendments are issued to standards as the need arises on the basis periodically; a standard along with amendments is reaffirmed when needed; if the review indicates that changes are needed, it is taken should ascertain that they are in possession of the latest amendments BIS Catalogue and Standards: Monthly Additions. This Indian Standard has been developed of comments. Standards are also reviewed such review indicates that no changes are up for revision. Users of Indian Standards or edition by referring to the latest issue of

from Dot : No. MTD 8 (4132).

Amendments Amend No.

Issued Since Publication Date of Issue Text Affected

BUREAU OF INDIAN STANDARDS Headquarters : Telegrams : Manaksanstha (Common to all offices) Telephone 323 76 17 323 38 41 337 84 99,337 ~85 61 337 86 26, 337 91 20 60 38 43 { 60 20 25 235 02 16,235 { 235 15 19,235 832 92 95,832 { 832 78 91,832 04 42 23 15 78 58 78 92

Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110 002 Telephones : 323 01 31,323 33 75,323 94 02 Regional Offices : Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg NEW DELHI 110 002 : l/14 C. I. T. Scheme VII M, V. I. P. Road, Kankurgachi CALCUTTA 700 054 : SC0 335-336, Sector 34-A, CHANDIGARH 160 022

Eastern

Northern

Southern

: C. I. T. Campus, IV Cross Road, CHENNAI

600 113

Western

: Manakalaya, E9 MIDC, Marol, Andheri MUMBAI 400 093

(East)

Branches

BANGALORE. BHOPAL. BHUBANESHWAR. COIMBATORE. : AHMADABAD. FARIDABAD. GHAZIABAD. GUWAHATI. HYDERABAD. JAIPUR. KANPUR. LUCKNOW. NAGPUR. PATNA. PUNE. RAJKOT. THIRUVANANTHAPURAM.