Yk-X e V5.21
Yk-X e V5.21
Users Manual
ENGLISH
YK-X series
E22-Ver. 5.21
Before using the robot (Be sure to read the following notes.)
At this time, our thanks for your purchase of this YAMAHA YK-X series SCARA robot. 1. Please be sure to perform the following tasks before using the robot. Failing to perform the tasks below will require re-teaching of the robot since the origin position cannot be set to the same previous position. Robot malfunctions (vibration, noise) may also occur. The origin position of the YK-X series robots is adjusted to the robot arm extended position at the factory prior to shipment, so the reference or standard coordinates are temporarily set. The customer should set the origin position before any other job. There are 2 types of origin position settings as shown below. [1] Setting the robot arm extended position (the origin position adjusted at the factory prior to shipment) as the origin position (When setting the origin position with the robot arm extended, you must check that there will not be any interference from any peripheral equipment during the next absolute reset.) [2] Setting a position OTHER than the robot arm extended position (the origin position adjusted at the factory prior to shipment) as the origin position [1] To set the robot arm extended position (the origin position adjusted at the factory prior to shipment) as the origin position Absolute Reset The YK-X series robots only require the absolute reset to be performed once when the robot is introduced. Once the absolute reset is performed, you do not need to reperform it when the power is turned on next time. Set the origin position while referring to absolute reset methods in "3. Adjusting the origin" in Chapter 4 of this manual and in "Absolute Reset" of the "YAMAHA Robot Controller User's Manual". Setting of reference coordinates is not required in the above case.
! CAUTION
Never enter the robot movement range once the robot servo is turned on as this is extremely hazardous.
[2] To set a position OTHER than the robot arm extended position (the origin position adjusted at the factory prior to shipment) as the origin position 1. Absolute reset The YK-X series robots only require the absolute reset to be performed once when the robot is introduced. Once the absolute reset is performed, you do not need to reperform it when the power is turned on next time. Set the origin position while referring to absolute reset methods in "3. Adjusting the origin" in Chapter 4 of this manual and in "Absolute Reset" of the "YAMAHA Robot Controller User's Manual". Set the origin position with the absolute reset.
! CAUTION
Never enter the robot movement range once the robot servo is turned on as this is extremely hazardous.
2. Affixing the origin position sticker Set in emergency stop when absolute reset is complete, and immediately affix the origin point sticker according to instructions in "6. Affixing Stickers for Origin Positions, Movement Directions and Axis Names" in Chapter 4 of this manual. 3. Setting the reference coordinates Set the reference coordinates while referring to instructions in "5. Setting the Reference Coordinates" in Chapter 4 of this manual and also to "Setting the Reference Coordinates" in the "YAMAHA Robot Controller User's Manual". Robot malfunctions (vibration, noise) may occur if the reference coordinates are not set correctly. Even though there is no problem with the robot, the following error messages are issued when the robot and controller are connected and power first turned on. (Actual error messages may differ according to how the robot and controller are connected.) Error messages issued when robot & controller are connected (RCX142) 17.81 : D?.ABS.battery wire breakage 17.83 : D?.Backup position data error 1 17.85 : D?.Backup position data error 2 17.92 : D?.Resolver disconnected during power off 17.93 : D?.Position backup counter overflow etc. Error messages issued when robot & controller are connected (RCX240) 17.81 : D?.ABS.battery wire breakage 17.83 : D?.Backup position data error 1 17.85 : D?.Backup position data error 2 17.92 : D?.Resolver disconnected during power off 17.93 : D?.Position backup counter overflow etc. 2. If the X, Y or R axis rotation angle is small. If the X, Y or R axis rotation angle is smaller than 5 so that it always moves in the same position, an oil film is difficult to be formed on the joint support bearing, possibly leading to damage to the bearing. In this type of operation, add a movement so that the joint moves through 90 or more, about 5 times a day.
Introduction
The YAMAHA YK-X series robots are SCARA type industrial robots developed based on years of YAMAHA experience and achievements in the automation field as well as efforts to streamline our in-house manufacturing systems. The YK-X series robots have a two-joint manipulator consisting of an X-axis arm and a Y-axis arm, and are further equipped with a vertical axis (Z-axis) and a rotating axis (R-axis) at the tip of the manipulator. The YK-X series robots can be used for a wide range of assembly applications such as installation and insertion of various parts, application of sealant, and packing operations. This instruction manual describes the safety measures, handling, adjustment and maintenance of YK-X series robots for correct, safe and effective use. Be sure to read this manual carefully before installing the robot. Even after you have read this manual, keep it in a safe and convenient place for future reference. This instruction manual should be used with the robot and considered an integral part of it. When the robot is moved, transferred or sold, send this manual to the new user along with the robot. Be sure to explain to the new user the need to read through this manual. This manual describes all models of the YK-X series except for the YK120X series. When you are using clean room models, dust/drip-proof models or ceiling-mount models of the YK-X series robots, refer to their user's manuals. For precautions and operations common to standard models of the YK-X series, please refer to this manual. If there are any obscure points in handling these robot models or other custom models, be sure to contact YAMAHA sales office or dealer. For details on specific operation and programming of the robot, refer to the separate "YAMAHA Robot Controller User's Manual".
NOTES The contents of this manual are subject to change without prior notice. Information furnished by YAMAHA in this manual is believed to be reliable.
However, if you find any part unclear or inaccurate in this manual, please contact YAMAHA sales office or dealer. YAMAHA MOTOR CO., LTD. IM Operations
MEMO
CONTENTS
CHAPTER 1 Using the Robot Safely
1 Safety Information ......................................................... 1-1 2 Essential Caution Items ................................................. 1-2 3 Industrial Robot Operating and Maintenance Personnel .... 1-10 4 Robot Safety Functions ............................................... 1-11 5 Safety Measures for the System ................................. 1-12 6 Trial Operation ............................................................. 1-13 7 Work Within the Safeguard Enclosure ......................... 1-14 8 Automatic Operation .................................................... 1-15 9 Warranty ...................................................................... 1-16
CHAPTER 2 Functions
1 Robot Manipulator ......................................................... 2-1 2 Robot Controller ............................................................ 2-7 3 Robot initialization number list ....................................... 2-8
CHAPTER 3 Installation
1 Robot Installation Conditions ......................................... 3-1
1-1 Installation environments ......................................................... 3-1 1-2 Installation base ....................................................................... 3-3
3 Protective Bonding ...................................................... 3-12 4 Robot Cable Connection ............................................. 3-14 5 User Wiring and User Tubing ...................................... 3-16 6 Attaching The End Effector .......................................... 3-20
6-1 R-axis tolerable moment of inertia and acceleration coefficient ... 3-20
6-1-1 Acceleration coefficient vs. moment of inertia (YK250X(H)) .. 3-22 6-1-2 Acceleration coefficient vs. moment of inertia (YK350X(H)) .. 3-23
6-1-3 Acceleration coefficient vs. moment of inertia (YK400X(H)) .. 6-1-4 Acceleration coefficient vs. moment of inertia (YK500X) ....... 6-1-5 Acceleration coefficient vs. moment of inertia (YK600X) ....... 6-1-6 Acceleration coefficient vs. moment of inertia (YK700X) ....... 6-1-7 Acceleration coefficient vs. moment of inertia (YK800X) ....... 6-1-8 Acceleration coefficient vs. moment of inertia (YK1000X) ..... 6-1-9 Acceleration coefficient vs. moment of inertia (YK1200X) ..... 6-1-10 Acceleration coefficient vs. moment of inertia (YK550X with standard R-axis specifications) ....................... 6-1-11 Acceleration coefficient vs. moment of inertia (YK550X with high-speed R-axis specifications) ...................
6-2 Equation for moment of inertia calculation ............................. 3-46 6-3 Example of moment of inertia calculation .............................. 3-49 6-4 Attaching the end effector ...................................................... 3-51 6-5 Gripping force of end effector ................................................ 3-56
7 Limiting the Movement Range with X-Axis Mechanical Stoppers (YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X) ... 3-57
7-1 YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X .. 3-58 7-2 YK550X .................................................................................. 3-61
8 Limiting the Movement Range with Y-Axis Mechanical Stoppers (YK550X only)............................................... 3-63 9 Limiting the Movement Range with X-, Y- and Z-Axis Mechanical Stoppers (YK250X, YK350X, YK400X, YK250XH, YK350XH, YK400XH) ... 3-64
9-1 Installing the X-, Y- and Z-axis additional mechanical stoppers ... 3-64 9-2 Installing the X- and Y-axis additional mechanical stoppers .. 3-67 9-3 Installing the Z-axis additional mechanical stopper ............... 3-69
9-3-1 Installing the minus direction stopper ..................................... 3-69 9-3-2 Installing the plus direction stopper ........................................ 3-72
9-4 Overrun amounts during impacts with X, Y and Z-axis additional mechanical stoppers .............................................................. 3-73
10 Working Envelope and Mechanical Stopper Positions for Maximum Working Envelope ................................... 3-74 11 Stopping Time and Stopping Distance at Emergency Stop ... 3-89
11-1 YK250X(H), YK350X(H), YK400X(H) .................................... 3-89 11-2 YK1200X ................................................................................ 3-97
CHAPTER 4 Adjustment
1 Overview ........................................................................ 4-1 2 Safety Precautions ........................................................ 4-1 3 Adjusting the origin ........................................................ 4-2
3-1 Absolute reset method ............................................................. 4-3
3-1-1 Sensor method (X-axis, Y-axis, and R-axis) ............................ 4-3 3-1-2 Mark method (X-axis, Y-axis, and R-axis) ................................ 4-4 3-1-3 Stroke end method (Z-axis) ..................................................... 4-4
3-2 Machine reference ................................................................... 4-5 3-3 Absolute reset procedures ....................................................... 4-6
3-3-1 Sensor method (X-axis, Y-axis, and R-axis) ............................ 4-6 3-3-2 Mark method (X-axis, Y-axis, and R-axis) ................................ 4-8
3-3-2-1 3-3-2-2 3-3-2-3 3-3-2-4 Absolute reset with servo on (re-reset) .................................. 4-9 Absolute reset with servo off (re-reset) ................................ 4-11 Absolute reset with servo on. (new reset) ............................ 4-13 Absolute reset with servo off. (new reset) ............................ 4-16
3-4 Changing the origin position and adjusting the machine reference .... 4-25
3-4-1 Sensor method ....................................................................... 4-26
3-4-1-1 3-4-1-2 3-4-1-3 YK250X(H), YK350X(H), YK400X(H) ................................... 4-26 YK500X, YK600X, YK700X,YK800X, YK1000X .................. 4-34 YK550X ................................................................................ 4-44
3-4-2 Mark method .......................................................................... 4-50 3-4-3 Stroke end method ................................................................. 4-51
3-4-3-1 3-4-3-2 YK250X(H), YK350X(H), YK400X(H), YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X .............................. 4-51 YK550X ................................................................................ 4-55
4 Setting the Soft Limits .................................................. 4-59 5 Setting the Standard Coordinates ............................... 4-62 6 Affixing Stickers for Origin Positions, Movement Directions and Axis Names .......................................... 4-63 7 Removing the Robot Covers ....................................... 4-65 8 Adjusting the Timing Belt Tension ................................ 4-70
8-1 Adjusting the belt tension (YK250X(H), YK350X(H), YK400X(H)) ... 4-71 8-2 Adjusting the belt tension (YK500X, YK600X) ....................... 4-73 8-3 Adjusting the belt tension (YK700X, YK800X, YK1000X) ...... 4-75 8-4 Adjusting the belt tension (YK1200X) .................................... 4-77 8-5 Adjusting the Z-axis and R-axis belts (YK550X) .................... 4-80
(1) (2) Adjusting the Z-axis belt tension ............................................ 4-80 Adjusting the R-axis belt tension ............................................ 4-83
YK500X, YK600X ................................................................... YK700X, YK800X, YK1000X .................................................. YK1200X ................................................................................ YK550X with high-speed R-axis specifications: R-axis ..........
CHAPTER 7 Specifications
1 Manipulator .................................................................... 7-1
1-1 Basic specification ................................................................... 7-1 1-2 External view and dimensions ................................................. 7-4 1-3 Robot inner wiring diagram .................................................... 7-30 1-4 Wiring table ............................................................................ 7-33
CHAPTER 1
MEMO
Safety Information
Industrial robots are highly programmable, mechanical devices that provide a large degree of freedom when performing various manipulative tasks. To ensure correct and safe use of YAMAHA industrial robots, carefully read this manual and make yourself well acquainted with the contents. FOLLOW THE WARNINGS, CAUTIONS AND INSTRUCTIONS INCLUDED IN THIS MANUAL. Failure to take necessary safety measures or mishandling due to not following the instructions in this manual may result in trouble or damage to the robot and injury to personnel (robot operator or service personnel) including fatal accidents. Warning information in this manual is shown classified into the following items.
DANGER
Failure to follow DANGER instructions will result in severe injury or death to the robot operator, a bystander or a person inspecting or repairing the robot.
WARNING
Failure to follow WARNING instructions could result in severe injury or death to the robot operator, a bystander or a person inspecting or repairing the robot.
! CAUTION Failure to follow CAUTION instructions may result in injury to the robot operator, a bystander or a person inspecting or repairing the robot, or damage to the robot and/or robot controller.
NOTE Explains the key point in the operation in a simple and clear manner. Refer to the user's manual by any of the following methods to operate or adjust the robot safely and correctly. 1. Operate or adjust the robot while referring to the printed version of the user's manual (available for an additional fee). 2. Operate or adjust the robot while viewing the CD-ROM version of the user's manual on your computer screen. 3. Operate or adjust the robot while referring to a printout of the necessary pages from the CD-ROM version of the user's manual. It is not possible to list all safety items in detail within the limited space of this manual. So it is essential that the user have a full knowledge of basic safety rules and also that the operator makes correct judgments on safety procedures during operation. For specific safety information and standards, refer to the applicable local regulations and comply with the instructions. This manual and warning labels supplied with or attached to the robot are written in English. Unless the robot operators or service personnel understand English, do not permit them to handle the robot. * Cautions regarding the official language of EU countries For equipment that will be installed in EU countries, the language used for the user's manuals, CE declarations, and operation screen characters is English only. Warning labels only have pictograms or else include warning messages in English. In the latter case, Japanese messages might be added.
1-1
(2) Use caution to prevent hands or fingers from being pinched or crushed. Warning labels 2 (Fig. 1-2) are affixed to the robot. See Fig. 2-2 to Fig. 2-6 for the locations of warning labels. Be careful not to let hands or fingers be pinched or crushed by the moving parts of the robot during transportation or teaching. WARNING
Moving parts can pinch or crush hands. Keep hands away from robot arms.
DANGER
Serious injury or death will result from impact with moving robot.
Keep outside of guard during operation. Lock out power before approaching robot.
WARNING
Moving parts can pinch or crush. Keep hands away from robot arms.
1-2
(3) Follow the instructions on warning labels and in this manual. Warning label 3 (Fig. 1-3) is affixed to the robot. See Fig. 2-2 to Fig. 2-6 for the locations of warning labels. Be sure to read the warning label and this manual carefully and make you thoroughly understand the contents before attempting installation and operation of the robot. Before starting the robot operation, even after you have read through this manual, read again the corresponding procedures and cautions in this manual as well as descriptions in this chapter (Chapter 1, "Using the Robot Safely"). Never install, adjust, inspect or service the robot in any manner that does not comply with the instructions in this manual. WARNING
Improper installation or operation can result in serious injury or death. Read user's manual and all warning labels before installation or operation.
WARNING
Improper Installation or operation can result in serious injury or death. Read user's(owner's) manual and all warning labels before operation.
Fig. 1-3 Warning label 3 (4) Do not use the robot in environments containing inflammable gas, etc. WARNING
This robot was not designed for operation in environments where inflammable or explosive substances are present. Do not use the robot in environments containing inflammable gas, dust or liquids. Explosions or fire could otherwise result.
(5) Do not use the robot in locations possibly subject to electromagnetic interference, etc. WARNING
Avoid using the robot in locations subject to electromagnetic interference, electrostatic discharge or radio frequency interference. Malfunction may otherwise occur.
1-3
(6) Use caution when releasing the Z-axis (vertical axis) brake. WARNING
The Z-axis will slide down when the Z-axis brake is released, causing a hazardous situation. Press the emergency stop button and prop up the Z-axis with a support stand before releasing the brake. Use caution not to let your body get caught between the Z-axis and installation base when releasing the brake to perform direct teach.
(7) Provide safety measures for end effector (gripper, etc.). WARNING
End effectors must be designed and manufactured so that they cause no hazards (for example, loosening of workpiece) even if power (electricity, air pressure, etc.) is shut off or power fluctuations occur. If there is a possible danger that the object gripped by the end effector may fly off or drop, then provide appropriate safety protection taking into account the object size, weight, temperature and chemical properties.
(8) Be cautious of possible Z-axis movement when the controller is turned off or emergency stop is triggered. (2-axis robots with air-driven Z-axis) WARNING
The Z-axis moves up when the power to the controller or PLC is turned off, the program is reset, emergency stop is triggered, or air is supplied to the solenoid valve for the Z-axis air cylinder. Do not let hands or fingers get caught and squeezed by moving parts of the Z-axis. Keep the usual robot position in mind so that the Z-axis will not interfere with obstacles during raising of the Z-axis, except in case of emergency stop.
(9) Use the following caution items when the Z-axis is interfering with peripheral equipment. (2-axis robots with air driven Z-axis) WARNING
When the Z-axis comes to a stop due to obstructions from peripheral equipment, the Z-axis may move suddenly when the obstruction is removed, causing injury such as pinched or crushed hands. Turn off the controller and reduce the air pressure before attempting to remove the obstruction. Before reducing the air pressure, place a support stand under the Z-axis because it will drop under its own weight.
1-4
(10) Use caution on Z-axis movement when air supply is stopped. (2axis robots with air-driven Z-axis) WARNING
The Z-axis may suddenly drop when the air pressure to the Z-axis air cylinder solenoid valve is reduced, creating a hazardous situation. Turn off the controller and place a prop or support under the Z-axis before cutting off the air supply.
(11) Use the following caution items when disassembling or replacing the pneumatic equipment. WARNING
Air or parts may fly outwards if pneumatic equipment is disassembled or parts replaced while air is still supplied. Do service work after first turning off the controller and reducing the air pressure. Before reducing the air pressure, place a support stand under the Z-axis (2axis robots with air driven Z-axis) since it will drop under its own weight.
(12) Use the following caution items when removing the Z-axis motor. WARNING
The Z-axis will drop when the Z-axis motor is removed, possibly resulting in injury. Turn off the controller and set a support stand under the Z-axis before removing the motor. Use caution not to allow hands or body to be squeezed or crushed by moving parts on the Z-axis or between the Z-axis and the installation base.
For precautions on handling the controller, refer to the "YAMAHA Robot Controller User's Manual".
1-5
(14) Consult us for corrective action when the robot is damaged or malfunction occurs. WARNING
If any part of the robot is damaged or any malfunction occurs, continuous operation may be very dangerous. Please consult YAMAHA dealer for corrective action.
Damage or Trouble Damage to machine harness or robot cable Damage to exterior of robot Abnormal operation of robot (positioning error, excessive vibration, etc.) Z-axis brake trouble Possible Danger Electrical shock, malfunction of robot Flying outwards of damaged parts during robot operation Malfunction of robot Dropping of load
(15) Use caution not to touch the X-axis motor cooling fan (YK550X) and controller cooling fan. WARNING
Bodily injury may occur from coming into contact with the cooling fan while it is rotating. When removing the fan cover for inspection, first turn off the controller and make sure the fan has stopped.
(16) Use caution not to touch the high temperature motor or speed reduction gear casing. WARNING
The motor and speed reduction gear casing are extremely hot after automatic operation, so burns may occur if these are touched. Before touching these parts during inspections or servicing, turn off the controller, wait for a while and check that the temperature has cooled.
1-6
(19) Do not allow any object to enter the X-axis motor cooling fan. (YK550X; See Fig. 2-6.) WARNING
If an object such as a small workpiece which the end effector failed to pick up, penetrates into the cooling fan for the X-axis motor, it may rebound and fly away from the fan, possibly causing bodily injury or damage to the fan. Provide a proper protective wall which prevents workpieces or other objects from entering the fan. When providing a protective wall, allow a space of at least 100mm between the fan vent and the wall to ensure air flow and cooling effects.
The robot must be operated with correct tolerable moment of inertia and acceleration coefficients according to the manipulator tip mass and moment of inertia. If this is not observed, premature end to the life of the drive units, damage to the robot parts or residual vibration during positioning may result.
(21) Do not use the robot for tasks requiring motor thrust.
! CAUTION
Avoid using the YK-X series robots for tasks which make use of motor thrust (press-fitting, burr removal, etc.). These tasks may cause malfunctions of the robot.
1-7
(23) Follow the specified procedures when installing, adjusting or inspecting the robot. WARNING
Always follow the specified procedures when installing, adjusting or inspecting the robot. Never attempt any procedure not described in this manual.
(24) Do not attempt any repair, parts replacement and modification. WARNING
Do not attempt any repair, parts replacement and modification unless described in this manual. These works require technical knowledge and skill, and may also involve work hazards.
(25) Precautions when disposing of the robot When disposing of the robot, handle it as industrial waste. (26) Location for installing the controller and the programming box The robot controller and programming box should be installed at a location that is outside the robot movement range yet where it is easy to operate and view the robot performing tasks. (27) Protect electrical wiring and hydraulic/pneumatic hoses as needed. Install a cover or similar item to protect the electrical wring and hydraulic/ pneumatic hoses from possible damage. (28) Install an operation status light. Install an operation status light (signal light tower, etc.) at an easy-to-see position so the operator will know whether the robot is merely stopped or is in emergency-error stop. (29) Clean work tools, etc. Work tools such as welding guns and paint nozzles which are mounted in the robot arm will preferably be cleaned automatically. (30) Provide adequate lighting. Make sure to provide enough lighting to ensure safety during work. (31) Draw up "work instructions" and makes sure the operator learns them well. Decide on "work instructions" for the following items in cases where personnel must work within the robot movement range to perform teaching, maintenance or inspection. Make sure the workers know these "work instructions" well.
1-8
(1) Robot operating procedures needed for tasks such as startup procedures and handling switches (2) Robot speeds used during tasks such as teaching (3) Methods for workers to signal each other when two or more workers perform tasks (4) Steps that the worker should take when a problem or emergency occurs (5) Steps to take after the robot has come to a stop when the emergency stop device was triggered, including checks for cancelling the problem or error state and safety checks in order to restart the robot. (6) In cases other than above, the following actions should be taken as needed to prevent hazardous situations due to sudden or unexpected robot operation or faulty robot operation, as listed below. 1. Show a display on the operator panel 2. Ensure the safety of workers performing tasks within the robot movement range 3. Clearly specify position and posture during work Position and posture where worker can constantly check robot movements and immediately move to avoid trouble if an error/problem occurs 4. Install noise prevention measures 5. Use methods for signaling operators of related equipment 6. Use methods to decide that an error has occurred and identify the type of error Implement the "work instructions" according to the type of robot, installation location, and type of work task. When drawing up the "work instructions", make an effort to include opinions from the workers involved, equipment manufacture's technicians, and workplace safety consultants, etc. (32) Display a sign on operation panel during work Display an easy to understand sign or message on the programming box and operation panel during the job task, to prevent anyone other than the operators for that job task from mistakenly operating a start or selector switch. If needed, take other measures such as locking the cover on the operation panel. (33) Make daily and periodic inspections. (1) Always make sure that daily and periodic inspections are performed, and make a pre-work check to ensure there are no problems with the robot or related equipment. If a problem or abnormality is found, then promptly repair it or take other measures as necessary. (2) When you make periodic inspections or repairs, make a record and store it for at least 3 years.
1-9
1-10
(4) Mechanical stoppers If the servo power is suddenly shut off during high-speed operation by emergency stop or safety functions, these mechanical stoppers prevent the axis from exceeding the movement range. The movement ranges of the X-axis arm can be limited as needed by use of mechanical stoppers. (Excluding the YK250X(H), YK350X(H) and YK400X(H)) On the Y-axis arm, mechanical stoppers are fixed at both ends of the maximum movement range. The Z-axis has a mechanical stopper at the upper end and lower end. No mechanical stopper is provided on the R-axis. Note: The movement range is the area limited by mechanical stoppers. WARNING
Axis movement will not stop immediately after the servo power supply is shut off by emergency stop or other safety functions.
(5) Z-axis (vertical axis) brake An electromagnetic brake is installed on the Z-axis to prevent the Z-axis from sliding down when servo power is turned off. This brake is working when the controller is off or the Z-axis servo power is off even when the controller is on. The Z-axis brake can be released by means of the programming box or by a command in the program when the controller is on.
1-11
WARNING
The Z-axis will slide down when the Z-axis brake is released, creating a hazardous situation. Press the emergency stop button and prop the Z-axis with a support stand before releasing the brake. Use caution not to let your body get caught between the Z-axis and installation base when releasing the brake to perform direct teach.
1-12
Trial Operation
After making installations, adjustments, inspections, maintenance or repairs to the robot, make a trial run using the following procedures. (1) If a safeguard enclosure has not yet been provided right after installation of the robot, rope off or chain off around the movement area of the manipulator in place of the safeguard enclosure, and observe the following points. 1. Use sturdy, stable posts which will not fall over easily. 2. The rope or chain should be easily visible by everyone around the robot. 3. Place a sign to keep the operator or other personnel from entering the movement range of the manipulator. (2) Check the following points before turning on the controller. 1. Is the robot securely and correctly installed? 2. Are the electrical connections to the robot correct? 3. Are items such as air pressure correctly supplied? 4. Is the robot correctly connected to peripheral equipment? 5. Have safety measures (safeguard enclosure, etc.) been taken? 6. Does the installation environment meet the specified standards? (3) After the controller is turned on, check the following points from outside the safeguard enclosure. 1. Does the robot start and stop as intended? Can the operation mode be selected correctly? 2. Does each axis move as intended within the soft limits? 3. Does the end effector move as intended? 4. Are the signal transmissions to the end effector and peripheral equipment correct? 5. Does emergency stop work? 6. Are the teaching and playback functions normal? 7. Are the safeguard enclosure and interlock working as intended? 8. Does the robot move correctly during automatic operation?
1-13
1-14
Automatic Operation
Automatic operation described here includes all operations in AUTO mode. (1) Check the following before starting automatic operation. 1. No one is within the safeguard enclosure. 2. The programming box and tools are in their specified locations. 3. The alarm or error lamps on the robot and peripheral equipment do not flash. 4. The safeguard enclosure is securely installed with safety interlocks actuated. (2) Observe the following during automatic operation or in cases where an error occurs. 1) After automatic operation has started, check the operation status and warning lamp to ensure that the robot is in automatic operation. 2) Never enter the safeguard enclosure during automatic operation. 3) If an error occurs in the robot or peripheral equipment, observe the following procedure before entering the safeguard enclosure. 1. Press the emergency stop button to set the robot to emergency stop. 2. Place a sign on the start switch, indicating that the robot is being inspected in order to keep any other person from touching the start switch and restarting the robot.
1-15
Warranty
The YAMAHA robot and/or related product you have purchased are warranted against the defects or malfunctions as described below. Warranty description : If a failure or breakdown occurs due to defects in materials or workmanship in the genuine parts constituting this YAMAHA robot and/or related product within the warranty period, then YAMAHA will repair or replace those parts free of charge (hereafter called "warranty repair"). : The warranty period ends when any of the following applies: (1) After 18 months (one and a half year) have elapsed from the date of shipment (2) After one year has elapsed from the date of installation (3) After 2,400 hours of operation
Warranty Period
Exceptions to the Warranty : This warranty will not apply in the following cases: (1) Fatigue arising due to the passage of time, natural wear and tear occurring during operation (natural fading of painted or plated surfaces, deterioration of parts subject to wear, etc.) (2) Minor natural phenomena that do not affect the capabilities of the robot and/or related product (noise from computers, motors, etc.). (3) Programs, point data and other internal data that were changed or created by the user. Failures resulting from the following causes are not covered by warranty repair. 1) Damage due to earthquakes, storms, floods, thunderbolt, fire or any other natural or man-made disasters. 2) Troubles caused by procedures prohibited in this manual. 3) Modifications to the robot and/or related product not approved by YAMAHA or YAMAHA sales representatives. 4) Use of any other than genuine parts and specified grease and lubricants. 5) Incorrect or inadequate maintenance and inspection. 6) Repairs by other than authorized dealers.
1-16
YAMAHA MOTOR CO., LTD. MAKES NO OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. THE WARRANTY SET FORTH ABOVE IS EXCLUSIVE AND IS IN LIEU OF ALL EXPRESSED OR IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR WARRANTIES ARISING FROM A COURSE OF DEALING OR USAGE OF TRADE. YAMAHA MOTOR CO., LTD. SOLE LIABILITY SHALL BE FOR THE DELIVERY OF THE EQUIPMENT AND YAMAHA MOTOR CO., LTD. SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES (WHETHER ARISING FROM CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY). YAMAHA MOTOR CO., LTD. MAKES NO WARRANTY WHATSOEVER WITH REGARD TO ACCESSORIES OR PARTS NOT SUPPLIED BY YAMAHA MOTOR CO., LTD.
1-17
MEMO
1-18
CHAPTER 2
Functions
1 Robot Manipulator ..................................................................2-1 2 Robot Controller .....................................................................2-7 3 Robot initialization number list ................................................2-8
MEMO
CHAPTER 2 Functions
Robot Manipulator
The YK-X series robots are available in 4-axis models having an X/Y-axis arm (equivalent to human arm) and a Z/R-axis (equivalent to human wrist). With these 4 axes, the YK-X series robots can move as shown in Fig. 2-1. By attaching different types of end effector (gripper) to the end of the arm, a wide range of tasks can be performed with high precision at high speeds. The (+) and (-) signs show the direction of axis movement when the jog keys on the programming box are pressed (standard setting at the factory). Fig. 2-2 to Fig. 2-6 on the subsequent pages show part names and functions of each robot model.
X-axis arm
Y-axis (+)
()
2-1
CHAPTER 2 Functions
D-sub connector for user wiring (No.1 to 10)
User tubing 1 (4 black) User tubing 2 (4 red) User tubing 3 (4 blue) Ball screw Machine harness
Z-axis motor R-axis motor Z-axis,R-axis pulley, belt Y-axis motor Y-axis arm X-axis arm X-axis speed reduction gear Y-axis mechanical stopper
Y-axis speed reduction gear Y-axis origin sensor R-axis origin sensor
Z-axis spline End effector attachment X-axis speed reduction gear X-axis motor Serial label
User tubing 1 (4 black) User tubing 2 (4 red) User tubing 3 (4 blue) Warning label 3
M4 ground terminal
Robot cable
CHAPTER 2 Functions
Eyebolt installation position User tubing 1 (6 black) User tubing 2 (6 red) X-axis movable mechanical stopper
D-sub connector for user wiring (No.1 to 20) User tubing 3 (6 blue) Y-axis mechanical stopper Machine harness
Ball screw
Y-axis motor Z-axis motor R-axis motor Y-axis speed reduction gear X-axis origin sensor
Y-axis arm Y-axis origin sensor Z-axis,R-axis pulley, belt X-axis speed reduction gear R-axis origin sensor X-axis motor R-axis speed reduction gear Z-axis spline End effector attachment Warning label 3 Serial label M4 ground terminal X-axis arm
CHAPTER 2 Functions
User tubing 1 (6 black) User tubing 2 (6 red) User tubing 3 (6 blue) Eyebolt installation position X-axis movable mechanical stopper
D-sub connector for user wiring (No.1 to 20) Ball screw Y-axis mechanical stopper Warning label 1 (Same on opposite side) Warning label 2 (Same on opposite side) Machine harness
X-axis arm
Y-axis arm Z-axis,R-axis pulley, belt R-axis speed reduction gear R-axis origin sensor Z-axis spline End effector attachment Warning label 3 Y-axis origin sensor X-axis speed reduction gear X-axis motor
Serial label M4 ground terminal User tubing 1 (6 black) User tubing 2 (6 red) User tubing 3 (6 blue) D-sub connector for user wiring (No.1 to 20) Robot cable
CHAPTER 2 Functions
X-axis movable mechanical stopper D-sub connector for user wiring (No.1 to 20) Eyebolt installation position
User tubing 1 (6 black) User tubing 2 (6 red) User tubing 3 (6 blue) Y-axis mechanical stopper
Warning label 1 (Same on opposite side) Warning label 2 (Same on opposite side) R-axis motor Z-axis motor Yaxis motor Y-axis speed reduction gear
X-axis arm
Y-axis arm Z-axis, R-axis pulley, belt Z-axis support shaft End effector attachment X-axis speed reduction gear
Serial label M4 ground terminal User tubing 1 (6 black) User tubing 2 (6 red) User tubing 3 ( 6blue) Robot cable D-sub connector for user wiring (No.1 to 20)
2-5
CHAPTER 2 Functions
User tubing 1 (6 black) User tubing 2 (6 blue) D-sub connector for user wiring (No.1 to 20)
Y-axis arm Z-axis motor, brake Warning label 2 Y-axis motor R-axis motor Warning label 3 Warning label1
M4 ground terminal User M4 tap (Same on opposite side) R-axis origin sensor Z-axis spline End effector attachment
X-axis speed reduction gear Z-axis, R-axis pulley, belt X-axis arm
User tubing 2 (6 blue) User tubing 1 (6 black) Fan (Rear side) X-axis motor Robot cable D-sub connector for user wiring (No.1 to 20) M4 ground terminal
Fan
2-6
CHAPTER 2 Functions
Robot Controller
The YK-X series robot comes supplied with a robot controller RCX142 or RCX240. For more details, refer to the separate "YAMAHA Robot Controller User's Manual".
OP.1
OP.3
RCX142
MODEL. SER. NO. MANUFACTURED FACTORY AUTOMATION EQUIPMENT MADE IN JAPAN
OP.1
OP.3
RCX240
CAUTION
XY YM BATT XY SEL
XY YM
BATT
ZR
ZR
RGEN
OP.4
RGEN P N ACIN
P SAFETY N
RM L N
ACIN
L RM N L1
EXT.E-STOP 13 14
N1
RCX142
RCX240
2-7
CHAPTER 2 Functions
Absolute reset must be performed after reinitializing the controller. Before reinitializing the controller, read the descriptions in "3. Adjusting the origin" in Chapter 4 and make sure you thoroughly understand the procedure.
! CAUTION
When the controller is initialized, the "ARM LENGTH" and "OFFSET PULSE" settings in the axis parameters will be erased, making the standard coordinate settings invalid. (For details on standard coordinates, see "5. Setting the Standard Coordinates" in Chapter 4.) If you do not want to change the origin position by initializing, make a note of the "ARM LENGTH" and "OFFSET PULSE" settings before initializing, and reenter their settings after initialization is complete.
Robot initialization number list (Origin mark model)
Robot initialization number 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 Model name YK250X(H) Z150 YK350X(H) Z150 YK400X(H) Z150 YK500X YK600X YK700X YK800X YK1000X YK1200X YK550X Z200 Z200 Z200 Z200 Z200 Z400 Robot initialization number 2010 2011 2012 2013 2014 2015 Model name YK500X YK600X YK700X YK800X YK1000X YK550XH Z300 Z300 Z400 Z400 Z400
* When initializing the robot controllers for clean room models and dust/drip proof models, use the robot initialization number for the robot models containing the same number.
[Example] YK250XC(H) Z150 : Origin sensor model YK250XP Z150 : Origin sensor model
Robot initialization number: 2100 (YK250X(H) Z150 : Same as origin sensor model)
2-8
CHAPTER 3
Installation
1 Robot Installation Conditions ..................................................3-1
1-1 1-2 Installation environments ................................................................. 3-1 Installation base ............................................................................... 3-3
2 Installation ..............................................................................3-5
2-1 2-2 2-3 Unpacking ........................................................................................ 3-5 Checking the product ....................................................................... 3-6 Moving the robot .............................................................................. 3-7
2-3-1 2-3-2 Moving the YK250X(H), YK350X(H), YK400X(H) ........................... 3-7 Moving the YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X, YK550X .......................................................................... 3-8
2-4
3 Protective Bonding ...............................................................3-12 4 Robot Cable Connection ......................................................3-14 5 User Wiring and User Tubing ...............................................3-16 6 Attaching The End Effector ...................................................3-20
6-1 R-axis tolerable moment of inertia and acceleration coefficient ..... 3-20
6-1-1 6-1-2 6-1-3 6-1-4 6-1-5 6-1-6 6-1-7 6-1-8 6-1-9 6-1-10 Acceleration coefficient vs. moment of inertia (YK250X(H)) .......... 3-22 Acceleration coefficient vs. moment of inertia (YK350X(H)) .......... 3-23 Acceleration coefficient vs. moment of inertia (YK400X(H)) .......... 3-24 Acceleration coefficient vs. moment of inertia (YK500X) ............... 3-25 Acceleration coefficient vs. moment of inertia (YK600X) ............... 3-28 Acceleration coefficient vs. moment of inertia (YK700X) ............... 3-31 Acceleration coefficient vs. moment of inertia (YK800X) ............... 3-34 Acceleration coefficient vs. moment of inertia (YK1000X) ............. 3-37 Acceleration coefficient vs. moment of inertia (YK1200X) ............. 3-40 Acceleration coefficient vs. moment of inertia (YK550X with standard R-axis specifications) ............................... 3-43 6-1-11 Acceleration coefficient vs. moment of inertia (YK550X with high-speed R-axis specifications) ........................... 3-44
Equation for moment of inertia calculation ..................................... 3-46 Example of moment of inertia calculation ...................................... 3-49 Attaching the end effector .............................................................. 3-51 Gripping force of end effector ........................................................ 3-56
7 Limiting the Movement Range with X-Axis Mechanical Stoppers (YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X) ... 3-57
7-1 7-2 YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X .......... 3-58 YK550X .......................................................................................... 3-61
8 Limiting the Movement Range with Y-Axis Mechanical Stoppers (YK550X only) .......................................................................3-63 9 Limiting the Movement Range with X-, Y- and Z-Axis Mechanical Stoppers (YK250X, YK350X, YK400X, YK250XH, YK350XH, YK400XH) .... 3-64
9-1 9-2 9-3 Installing the X-, Y- and Z-axis additional mechanical stoppers ..... 3-64 Installing the X- and Y-axis additional mechanical stoppers .......... 3-67 Installing the Z-axis additional mechanical stopper ....................... 3-69
9-3-1 9-3-2 Installing the minus direction stopper ............................................ 3-69 Installing the plus direction stopper ............................................... 3-72
9-4
Overrun amounts during impacts with X, Y and Z-axis additional mechanical stoppers ...................................................................... 3-73
10 Working Envelope and Mechanical Stopper Positions for Maximum Working Envelope ................................................3-74 11 Stopping Time and Stopping Distance at Emergency Stop ... 3-89
11-1 YK250X(H), YK350X(H), YK400X(H) ............................................ 3-89 11-2 YK1200X ........................................................................................ 3-97
CHAPTER 3 Installation
1-1
Installation environments
Be sure to install the robot in the following environments.
Items Allowable ambient temperature 0 to 40C Allowable ambient humidity Altitude Ambient environments 35 to 85% RH (non condensation) 0 to 1000 meters above sea level Avoid installing near water, cutting water, oil, dust, metallic chips and organic solvent. Avoid installation near corrosive gas and corrosive materials. Avoid installation in atmosphere containing inflammable gas, dust or liquid. Avoid installation near objects causing electromagnetic interference, electrostatic discharge or radio frequency interference. Vibration Air supply pressure, etc. Working space Do not subject to impacts or vibrations. Below 0.58MPa (6.0kgf/cm2); clean dry air not containing deteriorated compressor oil; filtration 40m or less Allow sufficient space margin to perform jobs (teaching, inspection, repair, etc.) Specifications
For detailed information on how to install the robot controller, refer to the separate "YAMAHA Robot Controller User's Manual". WARNING
Avoid installing the robot in locations where the ambient conditions may exceed the allowable temperature or humidity, or in environments where water, corrosive gases, metallic powder or dust are generated. Malfunction, failure or short circuits may otherwise result.
WARNING
This robot was not designed for operation in environments where inflammable or explosive substances are present. Do not use the robot in environments containing inflammable gas, dust or liquids. Explosions or fire could otherwise result.
WARNING
Avoid using the robot in locations subject to electromagnetic interference, electrostatic discharge or radio frequency interference. Malfunction may otherwise occur.
3-1
CHAPTER 3 Installation
WARNING
Do not use the robot in locations subject to excessive vibration. Robot installation bolts may otherwise become loose causing the manipulator to fall over.
3-2
CHAPTER 3 Installation
1-2
Installation base
1) Prepare a sufficiently rigid and stable installation base, taking account of the robot weight including the end effector (gripper), workpiece and reaction force while the robot is operating. The maximum reaction force (see Fig. 31) applied to the X-axis and Z-axis of each robot during operation is shown in the table below. These values are an instantaneous force applied to the robot during operation and do not indicate the maximum load capacity. The maximum reaction force
FXmax
Robot Model
MXmax
Nm 56 56 56 137 137 304 304 333 1029 216 kgfm 6 6 6 14 14 31 31 34 105 22
FZmax
N 40 40 40 89 89 159 159 127 108 135 kgf 4 4 4 9 9 16 16 13 11 14
N 305 330 391 708 735 1653 1707 1618 3293 628
YK250X(H) YK350X(H) YK400X(H) YK500X YK600X YK700X YK800X YK1000X YK1200X YK550X
Fxmax
Fig. 3-1 Maximum reaction force applied during operation 2) The parallelism of the installation base surface must be machined within a precision of 0.05mm/500mm. The robot base mount must be installed facing down and in a level position (except ceiling-mount models which should be installed with the base mount facing up). 3) Tap holes into the surface of the installation base. For machining dimensions and positions, refer to "1-2 External view and dimensions" in Chapter 7.
3-3
CHAPTER 3 Installation
4) Securely fix the installation base on the floor with anchor bolts. WARNING
Do not place the robot on a moving installation base. Excessive loads will be applied to the robot arm by movement of the installation base, resulting in damage to the robot.
! CAUTION
The manipulator positioning might decrease if the installation surface precision is insufficient.
! CAUTION
If the installation base is not sufficiently rigid and stable or a thin metallic plate is attached to the installation base, vibration (resonance) may occur during operation, causing detrimental effects on the manipulator work.
3-4
CHAPTER 3 Installation
Installation
2-1
Unpacking
WARNING
The robot and controller are heavy. Take sufficient care not to drop them during moving or unpacking as this may damage the equipment or cause bodily injury.
! CAUTION
When moving the robot or controller by equipment such as a forklift that require a license, only properly qualified personnel may operate it. The equipment and tools used for moving the robot should be serviced daily.
The YK-X series robot comes packed with a robot controller and accessories, according to the order specifications. Using a carrying cart (dolly) or forklift, move the package to near the installation base. Take sufficient care not to apply shocks to the equipment when unpacking it.
YK250X(H), YK350X(H), YK400X(H) Robot manipulator
Arm clamping stay (Used only for transportation. Remove after installation.) YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X, YK550X
3-5
CHAPTER 3 Installation
2-2
If there is any damage due to transportation or insufficient parts, please notify your YAMAHA sales office or dealer immediately.
Controller Robot
: RCX240 : YK250X(H), YK350X(H), YK400X(H), YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X, YK550X
Standard
STD. DIO connector ( 1) Power plug ( 1) Terminator ( 1) CD-ROM User's Manual Warning label ( 1)
OP.3 OP.1
RCX2
40
D-sub connector/hood ( 2)
A X Z B Y R
TOR MO
R PW SRV ERR B
RPB
XM
RO I/O
XY SEL BATT XY
YM
CO
RO I/O
ZR
Origin position stickers ( 2) Robot manipulator (YK500X,YK600X 3) YK-X series Eyebolts ( 2 or 3 for YK550X only)
ZM
BATT ZR SAFE
N TY L1 N1
RM
EXT. OP E-ST 14 13
RCX240controller
Eyebolts are not supplied with the YK250X, YK350X and YK400X
Option
* Refer to the "YAMAHA Robot Controller User's Manual" for details on the controller accessories and options. Fig. 3-3 Product configurations
3-6
CHAPTER 3 Installation
2-3
To check the mass of each robot, refer to "1-1 Basic specifications" in Chapter 7.
2-3-1
Support part
Fig. 3-4
3-7
CHAPTER 3 Installation
2-3-2
! CAUTION
When moving the robot by equipment such as cranes that require a license, only properly qualified personnel may operate it. The equipment and tools used for moving the robot should be serviced daily.
To move a robot (for example, the YK500X) correctly and safely, follow the procedure below. (See Fig. 3-5.) Use the same procedure to move other robots. 1) If the Z-axis is not at the origin position, perform return-to-origin from outside the safeguard enclosure. Then, turn off the controller and unplug the robot cable from the controller. (The Z-axis is fixed at the origin position prior to shipping.) 2) Remove the X-axis arm cover and set screws. 3) Fold the X and Y-axis arms as shown in the drawing, and clamp the Y axis arm to the robot pedestal by using the stay and bolts that come with the robot. If the arms cannot be folded in the carrying position due to the X-axis mechanical stoppers, then remove them. (When the robot is shipped, the mechanical stoppers are installed to provide the maximum movement range.) 4) Screw the two eyebolts securely into the tapped hole on the machined bearing surface of the X-axis arm. (Use three eyebolts for the YK550X.) 5) Wind the robot cable around the upper part of the robot pedestal so that it does not hang up on the base mount, then fasten the cable end with adhesive tape.
3-8
CHAPTER 3 Installation
6) Prepare two looped ropes with the same length to allow a good lifting balance, then pass each rope through each eyebolt and catch it on the hoist hook. (3 looped ropes are needed for the YK550X.) 7) Slightly lift the hoist so that each rope has light tension to hold the robot. In this state, remove the bolts securing the robot base to the pallet supplied or installation base (if robot is to be moved to another installation base). 8) Using caution to keep the balance of the robot and avoid subjecting it to any strong vibrations and shocks, operate the hoist carefully to move to the installation base. The angle between each rope and the arm surface should be kept at 45 degrees or more. 9) Slightly lower the robot on the installation base and temporarily secure it by tightening the bolts. (For tightening torque to secure the robot firmly, see the next section, "2-4 Installing the robot".) 10) Remove the ropes, eyebolts and arm clamping stay, then reattach the cover and the set screws on the X-axis arm. (Be sure to fit the set screws and the cover in position to protect the tapped holes for eyebolts.) Keep the eyebolts, arm clamping stay, bolts and pallet for future use in case the robot needs to be moved or transported.
3-9
CHAPTER 3 Installation
Set screw
Arm clamping stay (supplied with the robot) Bolt (2 pieces supplied with the robot) Tightening toeque 4.5Nm (46kgfcm) YK500X,YK600X
Robot cable
YK1200X Bolt (M1220 : YK500X to YK1000X, YK550X M1625 : YK1200X) Tightening toeque 71Nm (720kgfcm) Bolt and nut (4 pieces each supplied with the robot) Bearing surface for eyebolt
Fig. 3-5
3-10
YK550X
CHAPTER 3 Installation
2-4
Depth of tapped holes in installation base: Iron installation base Bolt diameter 1.5 or more Aluminum installation base Bolt diameter 3 or more
Installation base
3-11
CHAPTER 3 Installation
Protective Bonding
WARNING
Be sure to ground the robot and controller to prevent electrical shock.
WARNING
Turn off the controller before grounding the robot.
The robot must be grounded as follows: 1) Provide a terminal marked "PE" for the protective conductor of the entire system and connect it to an external protective conductor. In addition, securely connect the ground terminal on the robot pedestal to the same protective conductor. (See Fig. 3-7 for example of the YK500X.)
(Symbol 417-IEC-5019) 2) When the end effector uses an electrical device which, if it malfunctions, might make contact with the power supply, the user must provide proper grounding on his own responsibility. The YK-X series robots do not have a ground terminal for this purpose. 3) For details on protective bonding on the robot body to comply with CE marking, follow the instructions on protective bonding explained in the "YAMAHA Robot Controller User's Manual" or "CE marking Supplement Manual". 4) Use a ground cable with a conductor wire cross section of at least 2.0mm2 and a length within 1 meter.
3-12
CHAPTER 3 Installation
Ground symbol
M4 Ground terminal
3-13
CHAPTER 3 Installation
WARNING
In the RCX142 controller, the MOTOR connectors XM and ZM, and YM and RM each have identical shapes. In addition, the PI connectors XY and ZR have identical shapes. Do not confuse these connectors when making connections. Wrong connections may result in malfunction and hazardous situations.
WARNING
If the connector installation is inadequate or if there are contact failures in the pins, the robot may malfunction causing a hazardous situation. Reconfirm that each connector is securely installed before turning on the controller. To attach the PI connector securely, tighten the screws supplied with the robot. Take caution not to apply an excessive load to the connectors due to stress or tension on the cables.
WARNING
Lay out the cables so that they do not obstruct the movement of the manipulator. Determine the robot work area in which the robot cables will not interfere with the load or workpiece picked up by the manipulator. If the robot cables interfere with the movable parts of the robot, the cables may be damaged causing malfunction and hazardous situations. Refer to "1-2 External view and dimensions" in Chapter 7.
WARNING
Lay out the robot cables so as to keep the operator or any other person from tripping on them. Bodily injury may result if someone trips on the cables.
3-14
CHAPTER 3 Installation
Controller side connector Robot side connector XM RCX controller XM
YM
YM
ZM
ZM
RM
RM
Robot cable
XY
ZR
ZR
3-15
CHAPTER 3 Installation
1) The YK-X series robots are equipped with user wires and air tubes in the machine harness. The table below shows the number of wires and air tubes available for each robot model.
Robot model YK250X(H), YK350X(H), YK400X(H) YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X YK550X User wiring 10wires 20wires 20wires User tubing 4, 3tubes 6, 3tubes 6, 2tubes
(Robot models for custom specifications may have different wiring or tubing.) The specifications of the user wires and air tubes are shown below. Always observe the specifications.
User Wiring Rated voltage Allowable current Nominal cross-section area of conductor Shield 30V 1.5A 0.2mm2 Yes
User Tubing Maximum pressure Outer diameter inner diameter Fluid 0.58MPa (6Kgf/cm2) 4mm2.5mm 6mm4mm Dry clean air not containing deteriorated compressor oil; filtration 40m or less
2) A D-sub connector for user wiring and a bulkhead union for user tubing are provided one each on the arm side and pedestal side. For the locations, refer to "1-2 External view and dimensions" in Chapter 7.
3-16
CHAPTER 3 Installation
3) Signal wiring connections in the machine harness 1. YK250X(H), YK350X(H), YK400X(H) Connector pins 1 to 10 can be used. Pin 15 is connected to a shield wire and cannot be used as a signal wire.
Signal Connector NO 1 2 3 4 User signal line 5 IO (Arm side) 6 7 8 9 10 11 12 13 14 Shield Flame ground 15 6 7 8 9 10 11 12 13 14 15 1 FG Connection NO 1 2 3 4 5 IO (Base side) Connector Color Brown Red Orange Blue Violet Grey White Black Brown Red Orange Blue Violet Grey Green Green
(Robots models with non-standard specifications may have different wiring colors.) 2. YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X, YK550X Connector pins 1 to 20 can be used. Pin 25 is connected to a shield wire and cannot be used as a signal wire.
Signal Connector NO 1 2 3 4 5 6 7 8 9 User signal line IO (Arm side) 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Shield Flame Ground 25 Connection NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 FG Green Green IO (Base side) Connector Color Brown Red Orange Blue Violet Grey White Black Brown Red Orange Blue Violet Grey White Black Brown Red Orange Blue
(Robots models with non-standard specifications may have different wiring colors.)
3-17
CHAPTER 3 Installation
4) As shown in Fig. 3-9, solder the user cable wires to the D-sub connector (supplied with the robot). Reattach the hood to the D-sub connector after soldering, then plug it into the user wiring connector. The connector pinouts as viewed from the solder side are shown below.
Hood Soldering
D-sub connector
8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8
15 14 13 12 11 10 9
10 11 12 13 14 15
13 12 11 10 9
5 4
9 10 11 12 13
25 24 23 22 21 20 19 18 17 16 15 14
14 15 16 17 18 19 20 21 22 23 24 25
WARNING
Securely attach the D-sub connector (supplied with the robot) into the D-sub connector on the robot side, by tightening the screws on the connector hood. If this connector comes loose or comes off, malfunction may result.
WARNING
Avoid fastening the user cable or tube with the machine harness, as this may lead to harness breakage and malfunction.
3-18
CHAPTER 3 Installation
WARNING
Make sure that the user cable attached to the D-sub connector for user wiring and the tube attached to the bulkhead union for user tubing will not interfere with the robot movement, entangle around the robot or flap around during operation. Wiring and tubing might then be damaged causing malfunction of the robot.
WARNING
Lay out the user cable attached to the D-sub connector for user wiring and the tube attached to the bulkhead union for user tubing so that they do not obstruct the movement of the operator or any other persons. Bodily injury may result if anyone trips on the cable or air tube.
! CAUTION
The D-sub connector supplied with the robot should be connected to the arm side by pin contact, and to the pedestal side by socket contact. Use caution at these points when soldering.
! CAUTION
Be sure to use the D-sub connector and hood which are supplied with the robot. Using other types may result in contact failure.
D-sub connectors (supplied with robot)
Robot model YK250X(H), YK350X(H), YK400X(H) YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X, YK550X D-sub connector on arm side DA-15P-NR DB-25P-NR D-sub connector on base side DA-15S-NR DB-25S-NR Hood DA-C1-J10R DB-C2-J9R
5) To check the operation and signal transmission between the end effector and the controller or peripheral equipment after making connections, refer to "6. Trial operation" in Chapter 1.
3-19
CHAPTER 3 Installation
6-1
3-20
CHAPTER 3 Installation
! CAUTION
Depending on the Z-axis position, vibration may occur when the X, Y or R-axis moves. If this happens, reduce the X, Y or R-axis acceleration to an appropriate level.
! CAUTION
If the moment of inertia is too large, vibration may occur on the Z-axis depending on its operation position. If this happens, reduce the Z-axis acceleration to an appropriate level.
3-21
CHAPTER 3 Installation
6-1-1
100 80 60 40 20 0 0
0.01 0.1
0.02 0.2
0.03 0.3
0.04 0.4
0.05 0.5
100 80 60 40 20 0 0
0.01 0.1
0.02 0.2
0.03 0.3
0.04 0.4
0.05 0.5
100 80 60 40 20 0 0
0.01 0.1
0.02 0.2
0.03 0.3
0.04 0.4
0.05 0.5
3-22
CHAPTER 3 Installation
6-1-2
100 80 60 40 20 0 0
0.01 0.1
0.02 0.2
0.03 0.3
0.04 0.4
0.05 0.5
100 80 60 40 20 0 0
0.01 0.1
0.02 0.2
0.03 0.3
0.04 0.4
0.05 0.5
100 80 60 40 20 0 0
0.01 0.1
0.02 0.2
0.03 0.3
0.04 0.4
0.05 0.5
3-23
CHAPTER 3 Installation
6-1-3
0.01 0.1
0.02 0.2
0.03 0.3
0.04 0.4
0.05 0.5
0.01 0.1
0.02 0.2
0.03 0.3
0.04 0.4
0.05 0.5
0.01 0.1
0.02 0.2
0.03 0.3
0.04 0.4
0.05 0.5
3-24
CHAPTER 3 Installation
6-1-4
0.04 0.4
0.08 0.8
0.12 1.2
0.04 0.4
0.08 0.8
0.12 1.2
0.04 0.4
0.08 0.8
0.12 1.2
CHAPTER 3 Installation
AX, AY, AR (%) 100 80 60 40 20 0 0 0.005(0.05)
0.04 0.4
0.08 0.8
0.12 1.2
0.04 0.4
0.08 0.8
0.12 1.2
0.04 0.4
0.08 0.8
0.12 1.2
3-26
CHAPTER 3 Installation
AX, AY, AR (%) 100 80 60 40 20 0 0 0.007(0.07)
0.04 0.4
0.08 0.8
0.12 1.2
0.04 0.4
0.08 0.8
0.12 1.2
3-27
CHAPTER 3 Installation
6-1-5
0.04 0.4
0.08 0.8
0.12 1.2
0.04 0.4
0.08 0.8
0.12 1.2
0.04 0.4
0.08 0.8
0.12 1.2
CHAPTER 3 Installation
AX, AY, AR (%) 100 80 60 40 20 0 0 0.005(0.05)
0.04 0.4
0.08 0.8
0.12 1.2
0.04 0.4
0.08 0.8
0.12 1.2
0.04 0.4
0.08 0.8
0.12 1.2
3-29
CHAPTER 3 Installation
AX, AY, AR (%) 100 80 60 40 20 0 0 0.005(0.05)
0.04 0.4
0.08 0.8
0.12 1.2
0.04 0.4
0.08 0.8
0.12 1.2
3-30
CHAPTER 3 Installation
6-1-6
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
CHAPTER 3 Installation
AX, AY, AR (%) 100 80 60 40 20 0 0 0.01(0.1)
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
3-32
CHAPTER 3 Installation
AX, AY, AR (%) 100 80 60 40 20 0 0 0.01(0.1)
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
3-33
CHAPTER 3 Installation
6-1-7
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
CHAPTER 3 Installation
AX, AY, AR (%) 100 80 60 40 20 0 0 0.02(0.2)
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
3-35
CHAPTER 3 Installation
AX, AY, AR (%) 100 80 60 40 20 0 0 0.02(0.2)
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
3-36
CHAPTER 3 Installation
6-1-8
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
CHAPTER 3 Installation
AX, AY, AR (%) 100 80 60 40 20 0 0 0.01(0.1)
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
3-38
CHAPTER 3 Installation
AX, AY, AR (%) 100 80 60 40 20 0 0 0.02(0.2)
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
0.1 1.0
0.2 2.0
0.3 3.0
3-39
CHAPTER 3 Installation
6-1-9
AX, AY (%) 0.1(1.0)
100 80 60 40 20 0 0
100 80 60 40 20 0 0
0.5 5
1.0 10
1.5 15
2.0 20
0.5 5
1.0 10
1.5 15
2.0 20
100 80 60 40 20 0 0
100 80 60 40 20 0 0
0.5 5
1.0 10
1.5 15
2.0 20
0.5 5
1.0 10
1.5 15
2.0 20
100 80 60 40 20 0 0
100 80 60 40 20 0 0
0.5 5
1.0 10
1.5 15
2.0 20
0.5 5
1.0 10
1.5 15
2.0 20
Fig. 3-64
m=11 to 15kg
3-40
CHAPTER 3 Installation
AX, AY (%) 0.1(1.0) AR (%) 0.1(1.0)
100 80 60 40 20 0 0
100 80 60 40 20 0 0
0.5 5
1.0 10
1.5 15
2.0 20
0.5 5
1.0 10
1.5 15
2.0 20
100 80 60 40 20 0 0
100 80 60 40 20 0 0
0.5 5
1.0 10
1.5 15
2.0 20
0.5 5
1.0 10
1.5 15
2.0 20
100 80 60 40 20 0 0
100 80 60 40 20 0 0
0.5 5
1.0 10
1.5 15
2.0 20
0.5 5
1.0 10
1.5 15
2.0 20
3-41
CHAPTER 3 Installation
AX, AY (%) 0.5(5.0) AR (%) 100 80 60 40 20 0 0 0.3(3.0)
100 80 60 40 20 0 0
0.5 5
1.0 10
1.5 15
2.0 20
0.5 5
1.0 10
1.5 15
2.0 20
0.5 5
1.0 10
1.5 15
2.0 20
0.5 5
1.0 10
1.5 15
2.0 20
0.5 5
1.0 10
1.5 15
2.0 20
0.5 5
1.0 10
1.5 15
2.0 20
3-42
CHAPTER 3 Installation
6-1-10
Acceleration coefficient vs. moment of inertia (YK550X with standard R-axis specifications)
For YK550X with high-speed R-axis specifications, refer to Section 6-1-11.
AX, AY, AR (%) 100 80 60 40 20 0 0.0 0.04 0.4 0.08 0.8 0.1 0.12 1.0 1.2 IR (Kgm2) JR (Kgf cm sec2) 0.001 (0.01)
CHAPTER 3 Installation
6-1-11
Acceleration coefficient vs. moment of inertia (YK550X with high-speed R-axis specifications)
! CAUTION
If the acceleration on the X, Y or R axis is too high compared to the moment of inertia of the load, feedback error 2 or over-current error may occur. If this happens, reduce the acceleration.
0.001 (0.01)
3-44
CHAPTER 3 Installation
AX, AY, AR (%) 100 80 60 40 20 0 0.0 0.04 0.05 0.08 0.4 0.5 0.8 0.1 0.12 1.0 1.2 IR (Kgm2) JR (Kgf cm sec2) 0.001 (0.01)
3-45
CHAPTER 3 Installation
6-2
g : Gravitational acceleration (cm/sec2) m : Mass of material particle (kg) W : Weight of material particle (kgf)
Fig. 3-79 2) Moment of inertia for cylinder (part 1) The equation for the moment of inertia for a cylinder that has a rotation center such as shown in Fig. 3-80 is given below.
I= J=
2 D 4 h = mD (kgm2) 32 8 2 D 4 h = WD (kgf cm sec2) 32g 8g ... (Eq. 3.2) h
: Density (kg/m , kg/cm ) g : Gravitational acceleration (cm/sec2) m : Mass of cylinder (kg) W : Weight of cylinder (kgf)
3 3
Fig. 3-80
3-46
CHAPTER 3 Installation
3) Moment of inertia for cylinder (part 2) The equation for the moment of inertia for a cylinder that has a rotation center such as shown in Fig. 3-81 is given below.
I= J= D2 D2 h2 h2 D 2 h ) = m ( ) (kgm2) ( + + 4 4 3 3 16 4 D2 D2 h2 h2 D 2 h ) = W ( ) (kgf cm sec2) ( + + 4 4 3 3 16g 4g ... (Eq. 3.3)
: Density (kg/m3, kg/cm3) g : Gravitational acceleration (cm/sec2) m : Mass of cylinder (kg) W : Weight of cylinder (kgf)
h 2 h
Fig. 3-81 4) Moment of inertia for prism The equation for the moment of inertia for a prism that has a rotation center as shown in Fig. 3-82 is given as follows.
I= J= abc(a 2 +b 2 ) m(a2 +b 2 ) = (kgm2) 12 12 abc(a 2 +b 2 ) W(a2 +b 2 ) = (kgf cm sec2) 12g 12g ... (Eq. 3.4)
c 1/2a b a
: Density (kg/m3, kg/cm3) g : Gravitational acceleration (cm/sec2) m : Mass of prism (kg) W : Weight of prism (kgf)
Fig. 3-82
3-47
CHAPTER 3 Installation
5) When the object's center line is offset from the rotation center. The equation for the moment of inertia, when the center of the cylinder is offset by the distance "x" from the rotation center as shown in Fig. 3-83, is given as follows.
2 D 4 h D 2 hx2 = mD + mx2 (kgm2) + 32 4 8 2 2 4 D h D hx J= + 32g 4g
I=
= WD + Wx 8g g
(kgf cm sec2)
h
... (Eq. 3.5) : Density (kg/m3, kg/cm3) g : Gravitational acceleration (cm/sec2) m : Mass of cylinder (kg) W : Weight of cylinder (kgf)
D x
Fig. 3-83 In the same manner, the moment of inertia of a cylinder as shown in Fig. 3-84 is given by
D2 h2 D 2h D 2 h x 2 D2 m h2 )+ ( + ) + mx2 (kgm2) ( + = 4 4 3 16 4 4 3 D2 h2 D 2 h D 2h x 2 )+ ( J= + 4 3 16g 4g Cneter line 2 2 2 D h W Wx 2 ) + ( = + (kgf cm sec ) g 4g 4 3 I= ... (Eq. 3.6)
D
x h
Fig. 3-84 In the same manner, the moment of inertia of a prism as shown in Fig. 3-85 is given by
I= abc(a2 + b 2 ) m(a2 +b 2 ) + abcx2= + mx2 (kgm2) 12 12 abc(a 2 + b2 ) abcx2 J= + 12g g =
2 W(a 2 + b2 ) + Wx (kgf cm sec2) 12g g ... (Eq. 3.7) c b
Center line
x a
Fig. 3-85
3-48
CHAPTER 3 Installation
6-3
Stay
2cm 2cm
2cm
1cm
4cm
10cm 1cm
6cm
Chuck
Workpiece
4cm
2cm
From Fig. 3-87, the weight of the stay (Ws) is given as follows:
Ws = abc = 0.0078 12 2 2 = 0.37 (kgf)
2cm
5cm
2cm
12cm
Fig. 3-87 The moment of inertia of the stay (Js) is then calculated from Eq. 3-7.
2 2 0.37 52 Js = 0.37 (12 +2 ) + = 0.014 (kgf cm sec2) 12 980 980
3-49
CHAPTER 3 Installation
4cm
Fig. 3-88
10cm
R-axis
The moment of inertia of the workpiece (Jw) is then calculated from Eq. 3-5.
Jw= 0.097 22 0.097 102 + 8 980 980 = 0.010 (kgf cm sec2)
2cm
Fig. 3-89
4) Total weight The total weight (W) is calculated as follows: W = Ws + Wc + Ww = 0.84 (kgf) 5) Total moment of inertia The total moment of inertia (J) is then obtained as follows:
J = Js + Jc + Jw = 0.062 (kgf cm sec2)
3-50
CHAPTER 3 Installation
6-4
The manipulator part to which an end effector is attached must have adequate strength and rigidity, as well as gripping force to prevent positioning errors. Table 3-1 shows the maximum load that can be applied to the end effector attachment of each robot model. Recommended methods for attaching end effectors are shown in Table 3-2 and Fig. 3-92. Refer to Fig. 3-90 for details on the end effector attachment of each robot model. For YK550X, refer to "1-2 External view and dimensions" in Chapter 7. When checking end effector operation, refer to "6 Trial Operation" in Chapter 1.
Z-axis mechanical stopper (Hole for attaching user tool or 5 +0.2 0 R-axis rotation during direct teaching) Retaining ring to set the user tool (See cautions on page 3-55.)
41
36
O-ring groove for clean room models Spline shaft (hollow): hollow diameter 6
12 -0.018
3 0 (Hole for attaching user tool or R-axis rotation during direct teaching) Retaining ring to set the user tool (See cautions on page 3-55.) Spline shaft (hollow): hollow diameter 7
0
+0.2
41
36
M81.25, depth 15
16h7 -0.018
M81.25, depth 15
Retaining ring to set the user tool (See cautions on page 3-55.)
48
O-ring groove for clean room models Spline shaft (hollow): hollow diameter 10
41 (18 range)
18
0 -0.018
M121.75, depth 20
3-51
CHAPTER 3 Installation
8 +0.2 0 (Hole for attaching user tool or R-axis rotation during direct teaching) Z-axis mechanical stopper Retaining ring to set the user tool (See cautions on page 3-55.)
50.5
O-ring groove for clean room models Spline shaft (hollow): hollow diameter 10
45(22 range)
22
0 -0.021
M121.75, depth 20
69
45
47.8
M162 depth25
3-52
CHAPTER 3 Installation
Table 3-1
FXYmax
Robot Model YK250X(H) YK350X(H) YK400X(H) YK500X YK600X YK700X YK800X YK1000X YK1200X YK550X N 46 46 46 115 115 376 376 341 441 300 kgf 5 5 5 12 12 38 38 35 45 31
FZmax
N 40 40 40 89 89 178 159 159 39 135 kgf 4 4 4 9 9 18 16 16 4 14
FRmax
N 121 121 121 253 253 464 464 464 1215 295 kgf 12 12 12 26 26 47 47 47 124 30
MRmax
Nm 6 6 6 12 12 47 47 43 98 18 kgfm 0.6 0.6 0.6 1.3 1.3 4.8 4.8 4.4 10.0 1.8
Mmax
Nm 5 5 5 10 10 22 20 20 4.9 19 kgfm 0.5 0.5 0.5 1.0 1.0 2.3 2.0 2.0 0.5 1.9
FxYmax
3-53
CHAPTER 3 Installation
Table 3-2
Robot Model YK250X(H) YK350X(H) YK400X(H) YK500X YK600X YK700X YK800X YK1000X YK1200X YK550X Bolts Used M4 or lager M4 or lager M4 or lager M6 or lager M6 or lager M8 or lager M8 or lager M8 or lager M10 or lager M6 or lager
Number of bolts 2 or more 2 or more 2 or more 2 or more 2 or more 2 or more 2 or more 2 or more 2 or more 2 or more
Tightening torque
Nm 4.5 4.5 4.5 15.3 15.3 37.0 37.0 37.0 74.0 15.3 kgfcm 46 46 46 156 156 380 380 380 760 156
Hole diameter(mm)
12 12 12 18 18 22 22 22 25 16
+0.018 0 +0.018 0 +0.018 0 +0.018 0 +0.018 0 +0.021 0 +0.021 0 +0.021 0 0.01 +0.018 0
Slot
Tapped hole
Fig. 3-92
3-54
CHAPTER 3 Installation
WARNING
The end effector attachment must have adequate strength to withstand the loads listed in Table 3-1. If too weak, the attachment may break during robot operation and fragments fly off causing accidents or injuries.
WARNING
The end effector attachment must have sufficient rigidity versus the loads listed in Table 3-1. If this rigidity is inadequate, the end effector may vibrate during robot operation causing bad effects on the manipulator operation.
WARNING
When the end effector is attached by slot clamping, always observe the conditions listed in Table 3-2. If these are ignored, the end effector may come loose and fly off during robot operation, resulting in an accident or injury. In cases where other attachment methods are used, be sure that the end effector will not come off when the loads listed in Table 3-1 are applied.
WARNING
The tapped hole (see Figs. 3-90 and 3-92) provided on the lower part of the end effector attachment should be used only for preventing the end effector from coming loose. Do not fasten the end effector just by using this tapped hole. If the end effector is fastened only with this tapped hole, it may come loose from the attachment during robot operation and fly off resulting in accidents or injuries.
! CAUTION
Do not attempt to secure the user tool to the spline shaft by using the tapped hole (see Figs. 3-90 and 3-92) at the lower part of the end effector attachment, which will apply an axial force to the user tool positioning circlip (retaining ring). Trying to secure the tool in this way will damage the retaining ring.
3-55
CHAPTER 3 Installation
6-5
Azmax
3-56
CHAPTER 3 Installation
Limiting the Movement Range with X-Axis Mechanical Stoppers (YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X)
In the YK-X series (YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X), the movement range can be limited by changing the X-axis mechanical stopper positions. (The Y-axis mechanical stopper positions are fixed and cannot be changed.) When the robot is shipped from the factory, the movement range is set to the maximum. If the maximum movement range is too large compared to the actual work range, or the manipulator might interfere with peripheral units, then the movement range can be limited as outlined below. The X-axis mechanical stopper positions may slightly differ depending on machining precision. WARNING
Always turn off the controller before changing the movement range with mechanical stoppers.
! CAUTION
When the mechanical stoppers are installed, the soft limits must be set to a point inside the mechanical stopper positions. (Refer to "4 Setting the Soft Limits" in Chapter 4.)
! CAUTION
When installing the mechanical stoppers, use caution not to allow the mechanical stoppers to make contact with the urethane damper (see Fig. 3-97 to 3-98). If these make contact, the urethane damper might come off.
3-57
CHAPTER 3 Installation
7-1
3-58
CHAPTER 3 Installation
122
92
62
32
Fig. 3-94 Mechanical stopper positions and movement range (YK500X, YK600X)
123
9 3
63
33
Fig. 3-95 Mechanical stopper positions and movement range (YK700X, YK800X, YK1000X)
3-59
CHAPTER 3 Installation
128
103
78
53
28
3-60
CHAPTER 3 Installation
7-2
YK550X
To change the X-axis mechanical stopper positions, use the procedure below while referring to Fig. 3-97. 1) Turn the robot X-axis arm so that it faces the machine front. 2) Remove the cover on the X-axis. 3) The mechanical stoppers are not installed at the time of shipment, but the robot has fixed stoppers cast integrally with the arm. These are used for the maximum working envelope. To narrow the movement range, install the mechanical stoppers (supplied with the robot) securely in the desired positions A to C. Use a slotted screwdriver to tighten the stopper all the way into the tapped holes. For example, when the mechanical stoppers are installed in position A in Fig. 3-97, the X-axis arm is allowed to turn though an angle of 65 degrees from the front of the arm to the mechanical stopper. 4) Check that the movement range is limited by the mechanical stoppers as desired. 5) Reattach the cover to the X-axis.
3-61
CHAPTER 3 Installation
93
65
35
C
5
C B A
Urethane damper (When installing the mechanical stoppers, use caution not to allow the mechanical stoppers to make contact with the urethane dampers.)
Tapped hole for stopper installation Stopper for maximum working envelope
3-62
CHAPTER 3 Installation
Limiting the Movement Range with Y-Axis Mechanical Stoppers (YK550X only)
To change the Y-axis mechanical stopper positions, use the procedure below while referring to Fig. 3-98. 1) Turn the robot X and Y-axis arms so that they are nearly straight. 2) The mechanical stoppers are not installed at the time of shipment, but the robot has fixed stoppers cast integrally with the arm. These are used for the maximum working envelope. To narrow the movement range, install the mechanical stoppers (supplied with the robot) securely in the desired positions A to E. Use a slotted screwdriver to tighten the stopper all the way into the tapped holes. For example, when the mechanical stoppers are installed in position A in Fig. 3-98, the Y-axis arm is allowed to turn though an angle of 121 degrees from the front of the arm to the mechanical stopper. 3) Check that the movement range is limited by the mechanical stoppers as desired.
X-axis arm Stopper for maximum working envelope Tapped hole for stopper installation Urethane damper (When installing the mechanical stoppers, use caution not to allow the mechanical stoppers to make contact with the urethane dampers.)
D E
B A
E D
5
A C B
34
63
92
121
148
Stopper
3-63
CHAPTER 3 Installation
Limiting the Movement Range with X-, Yand Z-Axis Mechanical Stoppers (YK250X, YK350X, YK400X, YK250XH, YK350XH, YK400XH)
9-1
When the mechanical stoppers are installed, the soft limits must be set to a point inside the mechanical stopper positions.
Table 3-5
YK250X(H), YK350X(H), YK400X(H) No. Additional mechanical stopper parts in either direction of X-axis plus or minus direction, or in both directions (*1) Additional mechanical stopper parts in Y-axis plus direction Additional mechanical stopper parts in Y-axis minus direction q w e r t y r t y Part No. KN3-M2197-001 90112-10J045 99712-10600 KN3-M2197-001 90112-10J045 99712-10600 KN3-M2197-001 90112-10J045 99712-10600 Qty 1 1 1 1 1 1 1 1 1 Bolt Nut Stopper damper Bolt Nut Stopper damper Bolt Nut Remarks Stopper damper
*1: Use one each of these stopper parts to add the stopper in the plus or minus direction or even in both directions. (When changing the movement range in both directions, move the existing stopper position.)
3-64
CHAPTER 3 Installation
YK250X(H), YK350X(H), YK400X(H) No. Additional mechanical stopper parts in Z-axis plus direction YK250X,YK350X,YK400X No. Additional mechanical stopper parts in Z-axis minus direction YK250XH,YK350XH,YK400XH No. Additional mechanical stopper parts in Z-axis minus direction r Part No. KN3-M183A-100 Qty 1 Remarks Stopper block (supplied with bolt) r Part No. KN3-M183A-000 Qty 1 Remarks Stopper block (supplied with bolt) q w e Part No. KBE-M1780-000 KN3-M1789-000 91312-04012 Qty 1 1 2 Remarks Stopper block Damper Bolt
Table 3-6
YK250X(H), YK350X(H), YK400X(H) Standard stopper Stopper position in X-axis plus/minus directions Maximum movement position in X-axis plus/minus directions 132 115 Additional stopper 105 102
YK250X, YK350X Standard stopper Stopper position in Y-axis plus/minus directions Maximum movement position in Y-axis plus/minus directions YK400X Standard stopper Stopper position in Y-axis plus/minus directions Maximum movement position in Y-axis plus/minus directions YK250XH,YK350XH Standard stopper Stopper position in Y-axis plus/minus directions Maximum movement position in Y-axis plus/minus directions YK400XH Standard stopper Stopper position in Y-axis plus/minus directions Maximum movement position in Y-axis plus/minus directions 154 140 Additional stopper 88 85 142 140 Additional stopper 88 85 156 140 Additional stopper 88 85 145 140 Additional stopper 88 85
YK250X(H), YK350X(H), YK400X(H) Standard stopper Stopper position in Z-axis plus direction (*1) Maximum movement position in Z-axis plus direction (*1) Stopper position in Z-axis minus direction (*1) Maximum movement position (origin position) in Z-axis minus direction (*1) 158 mm 150 mm -5 mm 0 mm Additional stopper 158-L1 mm 100-L1 mm L2-5 mm L2 mm (*2)
*1: The Z-axis movement range and working envelope indicate the positions when the downward direction relative to the initial Z-axis origin position is set as the plus direction. The actual origin position is lowered by L2 and the movement range and stroke are reduced by L1+L2. *2: Depending on the relation to the Z-axis machine reference adjustment, L2 will be a position at 3 mm intervals, such as approximately 12mm, 15mm, etc.
3-65
CHAPTER 3 Installation
YK250X(H), YK350X(H), YK400X(H) Soft limit (pulses) Y-axis working envelope in plus direction Y-axis working envelope in minus direction
YK250X(H), YK350X(H), YK400X(H) Soft limit (pulses) Z-axis working envelope in plus direction Z-axis working envelope in minus direction L1 minimum value = 11, L2 minimum value = 12 16384 (150- (L1+L2)) /12 -683 Working envelope 150- (L1+L2) mm -0.5 mm
193422 -193422
Movement range: 158mm Working envelope: 150mm Movement range: 158-(L1+L2) Working envelope: 150-(L1+L2) Plus direction standard stopper L1
Fig. 3-99
3-66
CHAPTER 3 Installation
9-2
1) Prepare a hex wrench set. 2) Turn off the robot controller. 3) Place a sign indicating the robot is being adjusted, to keep others from touching the controller switch. 4) Enter the safeguard enclosure. 5) Remove the tapped-hole plug screw from the X-axis arm. 6) Place the damper q between the bolt head w and nut e, and then tighten the nut to the specified torque to secure the nut to the arm. Use the bolt and nut shown in Table 3-5. When adding the stopper in only one direction of the X-axis, do not remove the standard stopper. If it is removed, there will be no stopper on the opposite side. Only when changing the stopper position in both directions, remove the standard stopper to move its position. Screw the plug screw into the tapped hole where the standard stopper was installed. 7) Check that the movement range is limited by the stoppers as desired. 8) Go out of the safeguard enclosure. 9) Check that no one is inside the safeguard enclosure and then turn on the controller. 10) Set the soft limit in the X-axis plus direction as shown in Table 3-6. (When the stopper was installed in the minus direction, set the soft limit in the minus direction.) 11) Stay outside the safeguard enclosure and check that the maximum soft limits work to stop the X-axis arm at a point before the stopper position. Depending on the accuracy and position of the stopper parts, the X-axis arm may not stop until it reaches the stopper. In this case, set the soft limits smaller than the values shown in Table 3-6.
3-67
CHAPTER 3 Installation
y Tightening torque: 42Nm (425kgfcm) Place the damper between the bolt head and nut, and then tighten the nut to secure the parts to the arm side. Minus direction Plus direction Added Y-axis stopper r
q w t
e Tightening torque: 42Nm (425kgfcm) Place the damper between the bolt head and nut, and then tighten the nut to secure the parts to the arm side.
Stopper added in X-axis minus direction (Move and reinstall the standard stopper here.)
When installing the additional stoppers in both plus and minus directions
3-68
CHAPTER 3 Installation
9-3
9-3-1
Press the MODE key. Press the F3 key to enter MANUAL mode. Press the F13 key (LOWER+F3) to select "ABS Reset". After the Z-axis absolute reset is complete, press the F10 (UPPER+F5) key to display the adjustment machine reference value (%).
3-69
CHAPTER 3 Installation
When the machine reference is within the allowable range (between 26 and 74%), proceed to step 16). If the machine reference is outside the allowable range, adjust it as described in step 11) onward. 11) Turn off the controller and enter the safeguard enclosure. 12) Put a mark at the added stopper position and loosen the bolt for the added stopper. To adjust the machine reference value, move the added stopper as follows: Machine reference value < 26% : Move the added stopper in the plus direction. Machine reference value > 74% : Move the added stopper in the minus direction. As an approximate guide, a 3mm movement equals 100%. 13) Repeat the same procedure from step 6) until the machine reference is within the allowable range. 14) When the machine reference is set within the allowable range, go out of the safeguard enclosure. 15) Check that no one is inside the safeguard enclosure and then turn on the controller. 16) Set the soft limits as shown in Table 3-6. The soft limit in the minus direction is already set by default to the value shown in Table 3-6. 17) Stay outside the safeguard enclosure and check that the soft limits work to stop the Z-axis unit at a point before the stopper position. Depending on the accuracy and position of the stopper parts, the Z-axis unit may not stop until it reaches the stopper. In this case, set the soft limits larger than the values shown in Table 3-6. 18) Check that the movement range is limited by the stoppers as desired. 19) Turn off the controller and enter the safeguard enclosure. 20) Reattach the Y-axis arm cover.
3-70
CHAPTER 3 Installation
e Apply adhesive to the upper surface of q and bond e to q. q wTightening torque: 4.5Nm (46Kgfcm)
r Plus direction
Fig. 3-101
3-71
CHAPTER 3 Installation
9-3-2
3-72
CHAPTER 3 Installation
WARNING
The plus direction stopper will become a load, and so the Z-axis acceleration must be reduced as shown below. If not reduced, the service life of the Z-axis drive unit will decrease.
Tip load Z-axis acceleration 0kg 90% 1kg 90% 2kg 90% 3kg 85%
9-4
Overrun amounts during impacts with X, Y and Z-axis additional mechanical stoppers
A urethane damper is installed to absorb the shock when an impact occurs with the mechanical stopper, so a certain amount of overrun occurs when the robot strikes the mechanical stopper. Use caution and take overrun into account since the end effector may interfere with the robot body and peripheral equipment or the robot body may interfere with the peripheral equipment. Maximum overrun amounts are listed below (for normal operation, maximum payload, maximum speed).
X-axis 10 Y-axis 16 Z-axis Upper end Lower end 2mm 5mm
Note: Here, (deg.) is the overrun angle at the X-axis and Y-axis joints.
(1) When the robot strikes the X-axis or Y-axis mechanical stopper or another object, or when the R-axis collides with an object, speed reduction gears are locked while being meshed if the collision impact is large. If this happens, please contact our sales office or dealer. (2) If the X-axis, Y-axis or Z-axis mechanical stopper is deformed or damaged by impacts, please contact our sales office or dealer. Using the deformed or damaged mechanical stopper is dangerous, so it must be replaced. (3) After the robot strikes the Z-axis mechanical stopper, the stopper position may shift, and so check the stopper position. If shifted, move the stopper to the correct position and refasten it securely by following the assembly procedure.
3-73
CHAPTER 3 Installation
10
Working Envelope and Mechanical Stopper Positions for Maximum Working Envelope
Working envelope of each robot and mechanical stopper positions for the maximum working envelope are shown in Fig. 3-102 to Fig. 3-114.
Z-axis lower end 0 mechanical stopper position Interference position (a) Base flange (b) Base rear side
11 5
150
140
13
145
14
0 R25
145
5 11
13
R250
R86
R125
R7
90
90
120
63
CHAPTER 3 Installation
144.52
12
150
14 0
13 2
142
14 0
5 11
13
142
11 5
R25 0
25
R250
R86
R1
R8
R1
25
85
Manipulator interference area 140
85
59
Manipulator interference area 140
59
Working envelope
3-75
CHAPTER 3 Installation
150
145
11 5
145
5 11
R1
52
R3
50
132
132
R14
R3
50
R125
4( R3
140
b)
R1 5(a )
R12
R3 (a)
140
R
Manipulator interference area
( 11
b)
107
107
120
Working envelope
CHAPTER 3 Installation
12
150
13
14 2
14
14 0
14
5 11
132
R1
52
R3
50
R1
48
50 R3
R1
25
R34(
b)
R15(
a)
R12
140
140
99
99
140
3-77
CHAPTER 3 Installation
1522
0 Z-axis lower end mechanical stopper position Interference position (a) Base flange (b) Base rear side
150
5 11
156
11 5
156
R1
45
R4
00
132
132
R175
R6
R9
R400
R175
R1
) 4(b
(a )
140
140
120
86
86
120
Working envelope
CHAPTER 3 Installation
12
150
14 0
14
0
5 11
15
15
11 5
132
132
R40
R4
00
R145
R1 75
R10
R1
75
115
140
115
82 Manipulator interference area
82
140
Working envelope
CHAPTER 3 Installation
300
200
12
Interference position (a) Base flange (b) Base rear side (c) Base
12
2 12
12 2
00
00 R5
R7
12
R5
9( c)
R7
100
50 R1
R5
) 3(a
1(
42 R1
c)
R4
4(
a)
100
R2
R9 5
50
R2
5 R9
50
145
145
147
147
Working envelope
3-80
CHAPTER 3 Installation
300
200
0
12
12
Interference position (a) Base flange (b) Base rear side (c) Base
12 0
2 12
00
6 10
R6
R6
(a
00
( R98 a)
R2 50
12 2
12
2 R1
33 R1 ) (c
R1
R2 04
) 4(c
96
R2
50
8 R7
(b
R7
0(
b)
145
145
1 4 7
147
Working envelope
3-81
CHAPTER 3 Installation
0
12
400
12
Interference position (a) Base flange (b) Base rear side (c) Base
12
R7 0
12
R7
25
12 3
(c
R9
a 5(
00
R1
3 12
R1 14 (c )
50
R6
0(
b)
145
Working envelope
145
147
147
R3 50
45 R1
100
R3
R2 10
R1 99
R8
3(
a)
CHAPTER 3 Installation
8 200
400 12
12
Interference position (a) Base flange (b) Base rear side (c) Base
12
3 12
R8 00
4 R1
3(
R8
12
12
a)
00
R 4( 17
145
R2 59
R1
62
R2
(c)
47
3 R1
1(
a)
c)
R3
50
R3
50
0 R1
8(
b)
R9
6(
b)
145
147
147
Working envelope
3-83
CHAPTER 3 Installation
0
12 12
400
200
Interference position (a) Base flange (b) Base rear side (c) Base
00
12
12 3
R2
30
R3
(c)
15
20
R2
R3
R1
0(
R1
12
00
a)
12
15
00
(c)
8 R1
4(
a)
R4
6 R1
5(
b)
R1
49
(b)
145
145
147
147
Working envelope
3-84
R4 5
50
CHAPTER 3 Installation
400
Interference position (a) Base flange (b) Base rear side (c) Base
R1
12
R1
128
76 R1
R1
R1 2
(a
00
128
12 5
20 0
1 R3 1
0 R1
150
91 (c)
70 (c)
R1
55
(a
R6
00
R2
90
R6
00
(b
3 R8
150
(b
152
152
Working envelope
3-85
CHAPTER 3 Installation
3262
200
15
Fan position
Interference position (a) Base flange (b) Base rear side (c) Base
90
R6 2(
90
6(
5 R5
a)
a)
93
R2
93
R86 (c)
R1
59
R5
R5
50
(c
R172
R41 (b
145
145
R6
148
148 Radius in which load interferes with robot when X or Y-axis strikes mechanical stopper
Working envelope
X and Y-axis mechanical stopper positions (maximum working envelope) *The area between working envelope and X or Y-axis mechanical stopper position cannot be used.
3-86
CHAPTER 3 Installation
Here, working envelope and mechanical stopper positions for the maximum working envelope of a robot are described using the YK500X as an example. Refer to Fig. 3-108 YK500X. Other robot models are the same. 1) X and Y axes 1. Do not attempt operation outside the working envelope. On the YK-X series, the origin can be set at any position. The working envelope described in this manual is an area with the robot frontal reference. 2. Interference positions where a load may touch the robot within the working envelope and their radii are shown in the figure. Here, "a", "b" and "c" are the respective interference positions with the base flange, base rear panel, and base. Use caution not to allow the robot load to interfere with any part of the robot. 3. Interference positions where a load might touch the robot when the robot strikes the X-axis or Y-axis mechanical stoppers set for the maximum working envelope and their radii are shown at the mechanical stopper positions. Here, "a", "b" and "c" are the respective interference positions with the base flange, base rear panel, and base. 2) Z-axis Do not attempt work outside the working envelope. In particular, do not attempt work in the area between the working envelope and mechanical stopper position. Mechanical stoppers are installed at both the upper and lower ends of the movement range. WARNING
The robot cable, user wiring or tubing may be damaged if the robot load interferes with them resulting in hazardous robot malfunctions. Do not operate at points where the load may interfere with the robot cable, user wiring or tubing.
3-87
CHAPTER 3 Installation
4) Robot overrun during impacts with mechanical stopper A urethane damper is installed to absorb the shock when an impact occurs with the mechanical stopper, so a certain amount of overrun occurs when the robot strikes the mechanical stopper. Use caution and take overrun into account since the end effector may interfere with the robot body and peripheral equipment or the robot body may interfere with the peripheral equipment. Maximum overrun amounts are listed below (for normal operation, maximum payload, maximum speed).
Z-axis Robot model YK250X(H), YK350X(H), YK400X(H) YK500X, YK600X YK700X, YK800X, YK1000X YK550X X-axis 10 6 6 10 Y-axis 2 2 2 10 Upper end 2mm 5mm 5mm 1mm Lower end 2mm 2mm 2mm 4mm
Note: Here, (deg.) is the overrun angle at the X-axis and Y-axis joints.
1. When the robot strikes the X-axis or Y-axis mechanical stopper or another object, or when the R-axis collides with an object, speed reduction gears are locked while being meshed if the collision impact is large. If this happens, please contact our sales office or dealer. 2. When the robot strikes the Z-axis upper mechanical stopper excessively, the urethane damper may be splayed beyond the retaining ring. In this case, return the urethane damper to its original state. (All models except for YK550X)
3-88
CHAPTER 3 Installation
11
11-1
0.25
0.2
0.15
0.1
0.05
0 0 10 20 30 40 50 60 70 80 90 100
80 70 60 50 40 30 20 10 0
1kg X-axis 1kg Y-axis 2kg X-axis 2kg Y-axis 3kg X-axis 3kg Y-axis
10
20
30
40
50
60
70
80
90
100
Fig. 3-116 XY-arm plus direction stopping rotation angle for YK250X(H)
3-89
CHAPTER 3 Installation
0.3 1kg XY-axis 2kg XY-axis 3kg XY-axis
0.25
0.2
0.15
0.1
0.05
0 0 10 20 30 40 50 60 70 80 90 100
80 70 60 50 40 30 20 10 0 0 10
1kg X-axis 1kg Y-axis 2kg X-axis 2kg Y-axis 3kg X-axis 3kg Y-axis
20
30
40
50
60
70
80
90
100
Fig. 3-118 XY-arm minus direction stopping rotation angle for YK250X(H)
3-90
CHAPTER 3 Installation
0.4 1kg XY-axis 2kg XY-axis 3kg XY-axis
0.35
0.3
0.25
0.2
0.15
0.1
0.05
0 0 10 20 30 40 50 60 70 80 90 100
80 70 60 50 40 30 20 10 0 0 10
1kg X-axis 1kg Y-axis 2kg X-axis 2kg Y-axis 3kg X-axis 3kg Y-axis
20
30
40
50
60
70
80
90
100
Fig. 3-120 XY-arm plus direction stopping rotation angle for YK350X(H)
3-91
CHAPTER 3 Installation
0.4 1kg XY-axis 2kg XY-axis 3kg XY-axis
0.35
0.3
0.25
0.2
0.15
0.1
0.05
0 0 10 20 30 40 50 60 70 80 90 100
80 70 60 50 40 30 20 10 0 0 10
1kg X-axis 1kg Y-axis 2kg X-axis 2kg Y-axis 3kg X-axis 3kg Y-axis
20
30
40
50
60
70
80
90
100
3-92
CHAPTER 3 Installation
0.45 0.4 0.35 1kg XY-axis 2kg XY-axis 3kg XY-axis
80 70 60 50 40 30 20 10 0 0 10
20
30
40
50
60
70
80
90
100
Fig. 3-124 XY-arm plus direction stopping rotation angle for YK400X(H)
3-93
CHAPTER 3 Installation
0.45 0.4 0.35 1kg XY-axis 2kg XY-axis 3kg XY-axis
80 70 60 50 40 30 20 10 0 0 10
1kg X-axis 1kg Y-axis 2kg X-axis 2kg Y-axis 3kg X-axis 3kg Y-axis
20
30
40
50
60
70
80
90
100
Fig. 3-126 XY-arm minus direction stopping rotation angle for YK400X(H)
3-94
CHAPTER 3 Installation
0.05 0.045 0.04 1kg Z-axis 2kg Z-axis 3kg Z-axis
15
10
0 0 10 20 30 40 50 60 70 80 90 100
3-95
CHAPTER 3 Installation
0.05 0.045 0.04 0.035 1kg Z-axis 2kg Z-axis 3kg Z-axis
15
10
0 0 10 20 30 40 50 60 70 80 90 100
3-96
CHAPTER 3 Installation
11-2
YK1200X
2 1.8 1.6 16.5kg XY-axis 33kg XY-axis 50kg XY-axis
80 70 60 50 40 30 20 10 0 0 10
20
30
40
50
60
70
80
90
100
3-97
CHAPTER 3 Installation
0.07 16.5kg Z-axis 33kg Z-axis 50kg Z-axis
0.06
0.05
0.04
0.03
0.02
0.01
0 0 10 20 30 40 50 60 70 80 90 100
30
16.5kg 33kg
25
50kg
20
15
10
0 0 10 20 30 40 50 60 70 80 90 100
3-98
CHAPTER 4
Adjustment
1 Overview .................................................................................4-1 2 Safety Precautions .................................................................4-1 3 Adjusting the origin .................................................................4-2
3-1 Absolute reset method ..................................................................... 4-3
3-1-1 3-1-2 3-1-3 Sensor method (X-axis, Y-axis, and R-axis) .................................... 4-3 Mark method (X-axis, Y-axis, and R-axis) ....................................... 4-4 Stroke end method (Z-axis) ............................................................. 4-4
3-2 3-3
3-3-3
Stroke end method (Z-axis) ........................................................... 4-24 Sensor method .............................................................................. 4-26
3-4-1-1 3-4-1-2 3-4-1-3 YK250X(H), YK350X(H), YK400X(H) ........................................ 4-26 YK500X, YK600X, YK700X,YK800X, YK1000X ........................ 4-34 YK550X ..................................................................................... 4-44
3-4
Changing the origin position and adjusting the machine reference.... 4-25
3-4-1
3-4-2 3-4-3
4 Setting the Soft Limits ...........................................................4-59 5 Setting the Standard Coordinates ........................................4-62 6 Affixing Stickers for Origin Positions, Movement Directions and Axis Names .................................4-63 7 Removing the Robot Covers ................................................4-65
CHAPTER 4 Adjustment
Overview
YAMAHA robots have been completely adjusted at the factory or by the sales representative before shipment, including the origin position adjustment. If the operating conditions are changed and the robot must be adjusted, then follow the procedures described in this chapter.
Safety Precautions
(1) Read and understand the contents of this chapter completely before attempting to adjust the robot. (2) Place a conspicuous sign indicating the robot is being adjusted, to prevent others from touching the controller switch, programming box or operation panel. (3) If a safeguard enclosure has not yet been provided right after installation of the robot, rope off or chain off the movement area around the manipulator in place of a safeguard enclosure, and observe the following points. q Use stable posts which will not fall over easily. w The rope or chain should be easily visible by everyone around the robot. e Place a conspicuous sign prohibiting the operator or other personnel from entering the movement area of the manipulator. (4) To check operation after adjustment, refer to "6. Trial Operation" in Chapter 1.
4-1
CHAPTER 4 Adjustment
! CAUTION
After performing absolute reset, move the robot to a known point to check whether the origin position is correctly set. When doing this check, move the robot at the slowest possible speed.
! CAUTION
The standard coordinate and point data must be reset when the origin position is changed.
! CAUTION
Make point data setting after changing the origin position. After changing the origin position, do not use the previous point data.
4-2
CHAPTER 4 Adjustment
There are three absolute reset methods for the YK-X series: the sensor method, mark method, and stroke end method. The X-axis, Y-axis, and R-axis use the sensor method as the initial setting, while the Z-axis uses the stroke end method.
3-1
3-1-1
! CAUTION
The origin cannot be detected in any axis which is not positioned on the plus side from the origin (See Fig. 4-2.) before starting the return-to-origin operation. (Factory setting at shipment.) In this case, press the STOP key to interrupt the return-to-origin operation, move the target axis to the plus side of the origin, and reperform the origin return operation. If the return-to-origin operation is not interrupted, the robot will continue the operation and may collide with the mechanical stopper or a peripheral device. Since a mechanical stopper is not provided in the R-axis, the wiring and piping installed on the end effecter may be wound up by the operation.
4-3
CHAPTER 4 Adjustment
3-1-2
! CAUTION
The deviation between the origin position marks must be within a specified range (repeatability tolerance) when performing absolute reset at the same positions as the previous absolute reset. (See Fig. 4-4.) A position deviation (positional shift) will occur if absolute reset is performed at a position outside the repeatability tolerance or at a position different from the previous absolute reset position. Use the supplied origin position stickers to put a mark on the origin positions of the X-axis, Y-axis and R-axis, so that you can perform absolute reset at the origin positions within the tolerance range. Origin position repeatability (tolerance) values for each robot axis are shown in Table 4-1.
3-1-3
4-4
CHAPTER 4 Adjustment
3-2
Machine reference
The YK-X series position detectors are resolvers that have four positions where absolute reset can be performed per motor revolution. If the sensor method is used for the absolute reset, the origin position will be set at the positions where absolute reset can be performed soon after the origin sensor reacts to the dog (the origin signal is detected). The machine reference means the position relationship of the position where the robot detects the origin signal to the position where the absolute reset can be performed soon after detection. (See Fig. 4-1.) The machine reference is expressed with the ratio of interval A to interval B shown in Fig. 4-1. Interval A is the minimum distance between the positions where absolute reset can be performed and interval B is the distance between the position where the origin signal is detected and the position where absolute reset can be performed soon after the origin signal detection. The machine reference value is displayed on the optional MPB/RPB screen. (Unit: %) Machine reference value = B/A 100(%)
! CAUTION
The machine reference must be adjusted within a specified range to keep the repeatability precision of the absolute reset position. (The machine reference is factory-adjusted prior to shipping.) If the origin position is changed, the machine reference must be readjusted. For information on how to adjust the machine reference, refer to "3-4 Changing the origin position and adjusting the machine reference" in Chapter 4. When the temperature of the robot joint sections is high immediately after the robot has been operated, the machine reference value might be outside the specified range (40 to 60%). When checking or adjusting the machine reference value, always make sure that the temperature of the robot joint sections has returned to room temperature. Recommended machine reference value: 40 to 60%
Machine reference
Origin signal detection
Resolver A Positions where absolute reset can be performed B One motor revolution
MPB
MANUAL >RST. ABS Machine reference (%) M1= M4= 50 66 M2= 56 M3= 52 50% [MG] [S0H0J]
M1 R-axis
M2
M3 X-axis
M4 Y-axis
M5 Z-axis
Fig. 4-1
4-5
CHAPTER 4 Adjustment
3-3
3-3-1
The operation procedure using the MPB/RPB is described next. (Press the ESC key on the MPB/RPB if you want to return to the preceding step.) See the "YAMAHA Robot Controller User's Manual" for information on operating the robot controller. 1) Check that no one is inside the safeguard enclosure and then turn on the controller. 2) Place a sign indicating the robot is being adjusted, to keep others from touching the controller switch or operation panel. 3) Set the controller to MANUAL mode, if not in MANUAL mode. 4) Press the F13 (LOWER+F3) key to select "RST. ABS". 5) Select the axis for absolute reset. (X-axis: M1, Y-axis: M2, Z-axis: M3, Raxis: M4) To perform absolute reset on all axes, select "ALL" with the F11 (LOWER+F1) key.
! CAUTION
The Z-axis of the stroke end method first rises during the absolute reset of all axes (default setting). Be careful that your fingers do not get pinched or crushed by any sudden movement.
6) Check that the absolute reset axis must be positioned at the plus side of the origin. (See Fig. 4-2.) If it is not at the plus side, then press the jog key to move the target axis to the plus side. 7) Since the message "Reset ABS encoder OK?" is displayed, check that there are not any obstacles in the robot movement range, and press the F4 key (YES).
4-6
CHAPTER 4 Adjustment
8) After the absolute reset is completed, check that the machine reference value displayed on the MPB/RPB is between 40 and 60 (recommended range). If the machine reference value is outside the recommended range, then the next absolute reset may not be properly performed. In this case, refer to "3-4 Changing the origin position and adjusting the machine reference", and make the necessary adjustments.
Plus side
Minus side
Return-to-origin direction
Fig. 4-2
4-7
CHAPTER 4 Adjustment
3-3-2
To perform absolute reset using the same positions as the previous absolute reset.
The origin position mark can be seen from outside the robot movement range.
The origin position mark cannot be seen from outside the robot movement range.
The servo drive can safely guide the robot arm to the new origin position from outside the robot movement range.
The servo drive cannot safely guide the robot arm to the new origin position from outside the robot movement range.
4-8
CHAPTER 4 Adjustment
3-3-2-1
The operation procedure using the MPB/RPB is described next. (Press the ESC key on the MPB/RPB if you want to return to the preceding step.) See the "YAMAHA Robot Controller User's Manual" for information on operating the robot controller. 1) Check that no one is inside the safeguard enclosure and then turn on the controller. 2) Place a sign indicating the robot is being adjusted, to keep others from touching the controller switch or operation panel. 3) While holding the MPB/RPB, move to a position where the origin position sticker can be seen. Never enter within the robot movement range at this time. 4) Set the controller to MANUAL mode, if not in MANUAL mode. 5) Press the F13 (LOWER+F3) key to select "RST. ABS". 6) Select the axis for absolute reset. (X-axis: M1, Y-axis: M2, Z-axis: M3, Raxis: M4) To perform absolute reset on all axes, select "ALL" with the F11 (LOWER+F1) key.
! CAUTION
The Z-axis of the stroke end method first rises during the absolute reset of all axes (default setting). Be careful that your fingers do not get pinched or crushed by any sudden movement.
4-9
CHAPTER 4 Adjustment
7) Do as follows according to the axis that was selected. (1) X, Y and R axes 1. Jog the robot in steps using the F1 or F2 key so the origin position marks align with each other. (Robot movement speed can be adjusted with the F4 or F5 key.)
! CAUTION
There are several dispersed positions where absolute reset can be performed. All robot stop positions can be used for absolute reset when the robot was moved with the F1 or F2 key. Press the F1 or F2 key again before performing the absolute reset, move the axis left or right, and check that the origin position marks align with each other. (See Fig. 4-4.) A position deviation (position shift) occurs if absolute reset is performed at a position different from the previous absolute reset position.
2. When the robot has been moved to a position for absolute reset, check that the figure of the selected axis displayed on the MPB/RPB screen is within 26 from 74 (usually 50) and press the ENTER key. 3. A message "Reset ABS encoder OK?" appears so press the F4 (YES) key if this position is okay for reset. If "ALL" was selected in 6), then the message "Reset ABS encoder OK?" appears once again before the Z-axis rises. Check that there are no hazards even if the Z-axis rises and press the F4 (YES) key. (2) Z axis 1. The message "Reset ABS encoder OK?" appears so check that there are no obstacles in the robot movement area and press the F4 (YES) key. 2. After absolute reset is complete, check that the machine reference value shown on the MPB/RPB is between 26 and 74. If the machine reference value is outside these limits, then the absolute reset may not have been performed correctly. If the absolute reset is incorrect, adjust the Z-axis setting while referring to "Chapter 4, 3-4 Changing the origin position and adjusting the machine reference".
4-10
CHAPTER 4 Adjustment
3-3-2-2
The Z-axis (M3) uses the stroke end method to detect the origin position by having the axis making contact with a mechanical stopper at the end of the stroke. (default setting) This means that the servo must be turned on to perform Z-axis absolute reset. See "3-3-2-1 Absolute reset with servo on (re-reset)" for information on performing absolute reset on the Z-axis.
7) Move the robot manually to a position where the origin position marks are aligned with each other.
! CAUTION
The deviation between the origin position marks must be within a specified range (repeatability tolerance) when performing an absolute reset at the same position as the previous absolute reset. (See Fig. 4-4) A position deviation (positional shift) will occur if the absolute reset is performed at a position outside the repeatability tolerance or at a position different from the previous absolute reset position. When performing the absolute reset make sure that the deviation (positional shift) between the origin position marks is within the allowed tolerance for origin position repeatability. Origin position repeatability (tolerance) values for each robot axis are shown in Table 4-1.
4-11
CHAPTER 4 Adjustment
8) After moving the robot to a position for absolute reset, check that the figure of the selected axis displayed on the MPB/RPB screen is within 26 to 74 and press the ENTER key.
! CAUTION
There are several dispersed positions where absolute reset can be performed. Move the robot a little bit at a time while viewing the MPB/RPB screen so that the origin position marks match each other. Then press the ENTER key at a position where the selected axis figure is between 26 and 74 on the MPB/RPB screen.
! CAUTION
If the selected axis does not show a figure between 26 and 74, then an error message, "ABS.reset position error" appears during the next step and absolute reset is disabled.
9) A message "Reset ABS encoder OK?" appears, so press the F4 (YES) key if okay to reset at that position.
! CAUTION
If "ALL" was selected in 6) then the X-axis, Y-axis or R-axis can be reset in servo-off. However the servo must be on when performing absolute reset of the Z-axis. See "3-3-2-1 Absolute reset with servo on (re-reset)" for information on how to perform Z-axis absolute reset.
10) Go outside the safeguard enclosure. 11) Check that no one is inside the safeguard enclosure and then release the emergency stop button on the controller.
4-12
CHAPTER 4 Adjustment
3-3-2-3
The operation procedure using the MPB/RPB is described next. (Press the ESC key on the MPB/RPB if you want to return to the preceding step.) See the "YAMAHA Robot Controller User's Manual" for information on operating the robot controller. 1) Check that no one is inside the safeguard enclosure and then turn on the controller. 2) Place a sign indicating the robot is being adjusted, to keep others from touching the controller switch or operation panel. 3) Move the robot to the arm position where the absolute reset will be newly performed, and shift your own position while holding the MPB/RPB so you can see the joint area. Do not enter within the robot movement range. 4) Set the controller to MANUAL mode, if not in MANUAL mode. 5) Press the F13 (LOWER+F3) key to select "RST.ABS". 6) Select the axis for absolute reset. (X-axis: M1, Y-axis: M2, Z-axis: M3, Raxis: M4) To perform absolute reset on all axes, select "ALL" with the F11 (LOWER+F1) key.
! CAUTION
The Z-axis rises during absolute reset of all axes (default setting) so don't let fingers get pinched or crushed by sudden movement.
4-13
CHAPTER 4 Adjustment
7) Do as follows according to the axis that was selected. (1) X, Y and R axes 1. Press the F1 or F2 key to jog the robot in steps to the position where absolute reset is to be performed. (Robot movement speed is adjustable with F4 or F5 key.)
! CAUTION
There are several dispersed positions where absolute reset can be performed. All robot stop positions can be used for absolute reset when the robot was moved with the F1 or F2 key.
2. When the robot has been moved to a position for absolute reset, check that the figure of the selected axis displayed on the MPB/RPB screen is within 26 to 74 (usually 50) and press the ENTER key. 3. A message "Reset ABS encoder OK?" appears so press the F4 (YES) key if this position is okay for reset. If "ALL" was selected in 6), then the message "Reset ABS encoder OK?" appears once again before the Z-axis rises. Check that there are no hazards even if the Z-axis rises and press the F4 (YES) key. (2) Z-axis 1. The message "Reset ABS encoder OK?" appears so check that there are no obstacles in the robot movement area and press the F4 (YES) key. 2. After absolute reset is complete, check that the machine reference value shown on the MPB/RPB is between 26 and 74. If the machine reference value is outside these limits, then the absolute reset may not have been performed correctly. If the absolute reset is incorrect, adjust the Z-axis setting while referring to "Chapter 4, 3-4 Changing the origin position and adjusting the machine reference". 8) After absolute reset is complete, move all robot axes to their "0" pulse positions. To move axes to their "0" pulse positions, see Chapter 4, "Point trace function" in the "YAMAHA Robot Controller User's Manual".
! CAUTION
Before affixing the origin position stickers, be sure to move all robot axes back to their "0" pulse positions. Omitting this step may mean that the next absolute reset might be incorrect.
4-14
CHAPTER 4 Adjustment
9) After moving all the axes back to their "0" pulse positions, press the emergency stop button and affix the supplied origin position stickers to the upper and lower areas of the X-axis, Y-axis, and R-axis. Use these marked positions to perform an absolute reset if it is needed in the future. (See Fig. 4-5 to Fig. 4-8.) Use alcohol, etc. to remove any grease or oil from the surface where you will affix the stickers. After the surface dries attach the stickers securely. The YK550X does not have a relatively rotating part where the R-axis origin position sticker is attached. We recommend using the sensor method for detection the R-axis origin.
! CAUTION
The deviation between the origin position marks must be within a specified range (repeatability tolerance) when performing the absolute reset at the same position as the previous absolute reset. (See Fig. 4-4) When affixing an origin position sticker, align it precisely with the upper and lower stickers of the joint area so that the absolute reset position can be easily checked the next time an absolute reset is performed.
! CAUTION
Be careful not to let the robot joints move while attaching the origin stickers. When the servo is off, the robot joints may sometimes move due to tension in the harness from the arm position. If this is the case, the origin should be set to another position where the joints will not move.
10) Go outside the safeguard enclosure. 11) Check that no one is inside the safeguard enclosure and then release the emergency stop button on the controller.
4-15
CHAPTER 4 Adjustment
3-3-2-4
The Z-axis (M3) uses the stroke end method to detect the origin position by having the axis making contact with a mechanical stopper at the end of the stroke. (default setting) This means that the servo must be turned on to perform Z-axis absolute reset. See "3-3-2-3 Absolute reset with servo on (new reset)" for information on performing absolute reset on the Z-axis.
7) Move the robot manually to the position for performing absolute reset. 8) After moving the robot to a position for absolute reset, check that the figure of the selected axis displayed on the MPB/RPB screen is within 26 to 74 and press the ENTER key.
! CAUTION
There are several dispersed positions where absolute reset can be performed. Move the robot a little bit at a time while viewing the MPB/RPB screen, and press the ENTER key at a position where the figure of the selected axis is between 26 to 74 on the MPB/RPB screen.
4-16
CHAPTER 4 Adjustment
! CAUTION
If the selected axis does not show a figure between 26 and 74, then an error message, "ABS.reset position error" appears during the next step and absolute reset is disabled.
9) A message "Reset ABS encoder OK?" appears, so press the F4 (YES) key if okay to reset at that position.
! CAUTION
If "ALL" was selected in 6) then the X-axis, Y-axis or R-axis can be reset in servo-off. However the servo must be on when performing absolute reset of the Z-axis. See "3-3-2-3 Absolute reset with servo on (new reset)" for information on performing Z-axis absolute reset.
10) After absolute reset is complete, set the robot to servo-on and move all robot axes to their "0" pulse positions. To move axes to their "0" pulse positions, see Chapter 4, "Point trace function" in the "YAMAHA Robot Controller User's Manual".
! CAUTION
Before affixing the origin position stickers, be sure to move all robot axes back to their "0" pulse positions. Omitting this step may mean that the next absolute reset might be incorrect.
11) After moving all the axes back to their "0" pulse positions, press the emergency stop button and affix the supplied origin position stickers to the upper and lower areas of the X-axis, Y-axis, and R-axis. Use these marked positions to perform an absolute reset if it is needed in the future. (See Fig. 4-5 to Fig. 4-8.) Use alcohol, etc. to remove any grease or oil from the surface where you will affix the stickers. After the surface dries attach the stickers securely.
! CAUTION
The deviation between the origin position marks must be within a specified range (repeatability tolerance) when performing the absolute reset at the same position as the previous absolute reset. (See Fig. 4-4) When affixing an origin position sticker, align it precisely with the upper and lower stickers of the joint area so that the absolute reset position can be easily checked the next time an absolute reset is performed.
4-17
CHAPTER 4 Adjustment
! CAUTION
Be careful not to let the robot joints move while attaching the origin stickers. When the servo is off, the robot joints may sometimes move due to tension in the harness from the arm position. If this is the case, the origin should be set to another position where the joints will not move.
12) Go outside the safeguard enclosure. 13) Check that no one is inside the safeguard enclosure and then release the emergency stop button on the controller.
4-18
CHAPTER 4 Adjustment
YK500X, YK600X Origin position repeatability tolerance ( ) Origin position repeatability tolerance (mm) 0.56 0.56 0.90 0.58 0.47 0.65
YK700X, YK800X Origin position repeatability tolerance ( ) Origin position repeatability tolerance (mm) 0.56 0.56 0.90 YK1000X Origin position repeatability tolerance ( ) 0.45 0.56 0.90 YK1200X Origin position repeatability tolerance ( ) 0.37 0.43 0.90
Repeatability tolerance
0.76 0.62 0.73 Origin position repeatability tolerance (mm) 0.62 0.62 0.73 Origin position repeatability tolerance (mm) 0.64 0.58 0.89
OK
Origin position sticker Repeatability tolerance
OK
Origin position sticker Repeatability tolerance
NG
Origin position sticker Repeatability tolerance
NG
Origin position sticker
CHAPTER 4 Adjustment
Fig. 4-5 Origin position mark setting example YK250X(H), YK350X(H), YK400X(H)
4-20
CHAPTER 4 Adjustment
4-21
CHAPTER 4 Adjustment
Fig. 4-7 Origin position mark setting example YK700X, YK800X, YK1000X
4-22
CHAPTER 4 Adjustment
4-23
CHAPTER 4 Adjustment
3-3-3
The operation procedure using the MPB/RPB is described next. (Press the ESC key on the MPB/RPB if you want to return to the preceding step.) See the "YAMAHA Robot Controller User's Manual" for information on operating the robot controller. 1) Check that no one is inside the safeguard enclosure and then turn on the controller. 2) Place a sign indicating the robot is being adjusted, to keep others from touching the controller switch or operation panel. 3) Set the controller to MANUAL mode, if not in MANUAL mode. 4) Press the F13 (LOWER+F3) key to select "RST. ABS".3-4 5) Select M3 (Z-axis). 6) Since the message "Reset ABS encoder OK?" is displayed, check that there are not any obstacles in the robot movement range, and press the F4 key (YES). 7) After the absolute reset is completed, check that the machine reference value displayed on the MPB/RPB is within the absolute reset tolerance range (26 to 74). If the machine reference value is outside the absolute reset tolerance range, then the next absolute reset may not be properly performed. In this case, refer to "Chapter 4, 3-4 Changing the origin position and adjusting the machine reference" and make the necessary adjustments.
4-24
CHAPTER 4 Adjustment
3-4
If the origin position has been changed, then the absolute reset must be performed, the machine reference must be adjusted, and the standard coordinate and point data must be reset.
! CAUTION
If any machine reference is adjusted, the origin position may change. Before the adjustment, mark off the reference mark at the current origin position on the main body of the robot. After the machine reference is adjusted, be sure to check that the origin position has not deviated. If the origin position changes after the machine reference has been adjusted, then the standard coordinate and point data must be reset.
4-25
CHAPTER 4 Adjustment
3-4-1
Sensor method
3-4-1-1
9) Refer to Fig. 4-9 and Table 4-2 and turn the dog ring to the minimum extent. 10) Tighten the setscrews to fasten the dog ring. 11) Go out of the safeguard enclosure, and check that no one is inside the safeguard enclosure. Then turn on the controller. 12) Perform the absolute reset from outside the safeguard enclosure.
4-26
CHAPTER 4 Adjustment
13) After the absolute reset is completed, read the machine reference value displayed on the MPB/RPB. 14) If the machine reference value is in the range between 40 and 60 (recommended range), then the machine reference has been completely adjusted. If it is outside the recommended range, then repeat the procedure that starts in 5) to readjust it.
4-27
CHAPTER 4 Adjustment
The method to change the X-axis origin position is as follows. 1) Prepare the necessary tools. Hex wrench set 2) Check that no one is inside the safeguard enclosure and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) Place a sign indicating that the robot is being adjusted in order to keep others from operating the controller or operation panel. 5) Turn off the controller and enter the safeguard enclosure. 6) Use the hex wrench to loosen two setscrews which fasten the dog ring of the X-axis joint area. (See Fig. 4-9.)
! CAUTION
It is sufficient to loosen them. It is not necessary to completely remove them.
7) Turn the dog ring to move the sensor detection area (dog) on the dog ring to the desired origin position. 8) Tighten the setscrews to fasten the dog ring. 9) Go out of the safeguard enclosure, and check that no one is inside the safeguard enclosure. Then turn on the controller. 10) Perform the absolute reset from outside the safeguard enclosure. 11) After the absolute reset is completed, read the machine reference value displayed on the MPB/RPB. 12) If the machine reference value is in the range between 40 and 60 (recommended range), then the origin position has been completely changed. If it is outside the recommended value, then adjust the machine reference by referring to "1-1 Adjusting the X-axis machine reference".
4-28
CHAPTER 4 Adjustment
2-1 Adjusting the Y-axis machine reference The adjustment method for the Y-axis machine reference is as follows. 1) Prepare the necessary tools. Hex wrench set 2) Check that no one is inside the safeguard enclosure and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) If any machine reference value displayed on the MPB/RPB is not in the range between 40 and 60 (recommended range) after the absolute reset has been completed, then proceed with the following adjustment procedure. 5) Place a sign indicating that the robot is being adjusted in order to keep others from operating the controller or operation panel. 6) Turn off the controller and enter the safeguard enclosure. 7) Mark off the reference mark at the current origin position on the Y-axis joint area of the robot. At this time, be careful to prevent the origin position from deviating since the Y-axis arm is touched. 8) Use the hex wrench to loosen two setscrews which fasten the dog ring of the Y-axis joint area. (See Fig. 4-9.)
! CAUTION
9) Refer to Fig. 4-9 and Table 4-2 and turn the dog ring to the minimum extent. 10) Tighten the setscrews to fasten the dog ring. 11) Go out of the safeguard enclosure, and check that no one is inside the safeguard enclosure. Then turn on the controller. 12) Perform the absolute reset from outside the safeguard enclosure. 13) After the absolute reset is completed, read the machine reference value displayed on the MPB/RPB. 14) If the machine reference value is in the range between 40 and 60 (recommended range), then the machine reference has been completely adjusted. If it is outside the recommended range, then repeat the procedure that starts in 5) to readjust it.
4-29
CHAPTER 4 Adjustment
The method to change the Y-axis origin position is as follows. 1) Prepare the necessary tools. Hex wrench set 2) Check that no one is inside the safeguard enclosure and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) Place a sign indicating that the robot is being adjusted in order to keep others from operating the controller or operation panel. 5) Turn off the controller and enter the safeguard enclosure. 6) Use the hex wrench to loosen two setscrews which fasten the dog ring of the Y-axis joint area. (See Fig. 4-9.)
! CAUTION
It is sufficient to loosen them. It is not necessary to completely remove them.
7) Turn the dog ring to move the sensor detection area (dog) on the dog ring to the desired origin position. 8) Tighten the setscrews to fasten the dog ring. 9) Go out of the safeguard enclosure, and check that no one is inside the safeguard enclosure. Then turn on the controller. 10) Perform the absolute reset from outside the safeguard enclosure. 11) After the absolute reset is completed, read the machine reference value displayed on the MPB/RPB. 12) If the machine reference value is in the range between 40 and 60 (recommended range), then the origin position has been completely changed. If it is outside the recommended value, then adjust the machine reference by referring to "2-1 Adjusting the Y-axis machine reference".
4-30
CHAPTER 4 Adjustment
3-1 Adjusting the R-axis machine reference The adjustment method for the R-axis machine reference is as follows. 1) Prepare the necessary tools. Hex wrench set 2) Check that no one is inside the safeguard enclosure and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) If any machine reference value displayed on the MPB/RPB is not in the range between 40 and 60 (recommended range) after the absolute reset has been completed, then proceed with the following adjustment procedure. 5) Place a sign indicating that the robot is being adjusted in order to keep others from operating the controller or operation panel. 6) Turn off the controller and enter the safeguard enclosure. 7) Mark off the reference mark at the current origin position on the R-axis area of the robot. At this time, be careful not to touch the tool at the tip of the robot arm so that the origin position does not shift. 8) Use the hex wrench to loosen the two setscrews which fasten the dog ring on the R-axis area. (See Fig. 4-9.)
! CAUTION
9) Refer to Fig. 4-9 and Table 4-2 and turn the dog ring to the minimum extent. 10) Tighten the setscrews to fasten the dog ring. 11) Go out of the safeguard enclosure, and check that no one is inside the safeguard enclosure. Then turn on the controller. 12) Perform the absolute reset from outside the safeguard enclosure. 13) After the absolute reset is completed, read the machine reference value displayed on the MPB/RPB. 14) If the machine reference value is in the range between 40 and 60 (recommended range), then the machine reference has been completely adjusted. If it is outside the recommended range, then repeat the procedure that starts in 5) to readjust it.
4-31
CHAPTER 4 Adjustment
The method to change the R-axis origin position is as follows. 1) Prepare the necessary tools. Hex wrench set 2) Check that no one is inside the safeguard enclosure and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) Place a sign indicating that the robot is being adjusted in order to keep others from operating the controller or operation panel. 5) Turn off the controller and enter the safeguard enclosure. 6) Use the hex wrench to loosen the two setscrews which fasten the dog ring on the R-axis area. (See Fig. 4-9.)
! CAUTION
It is sufficient to loosen them. It is not necessary to completely remove them.
7) Turn the dog ring to move the sensor detection area (dog) on the dog ring to the desired origin position. 8) Tighten the setscrews to fasten the dog ring. 9) Go out of the safeguard enclosure, and check that no one is inside the safeguard enclosure. Then turn on the controller. 10) Perform the absolute reset from outside the safeguard enclosure. 11) After the absolute reset is completed, read the machine reference value displayed on the MPB/RPB. 12) If the machine reference value is in the range between 40 and 60 (recommended range), then the origin position has been completely changed. If it is outside the recommended value, then adjust the machine reference by referring to "3-1 Adjusting the R-axis machine reference".
4-32
CHAPTER 4 Adjustment
w
R-axis origin sensor Y-axis origin sensor Y-axis dog Y-axis dog ring
Table 4-2
Axis Movement amount (mm) for 100% of machine reference X 1.88 1.54 1.38
Machine reference > 60% : Movement in direction w
q Set screw (One each on opposite sides) Set screw (One each on opposite sides) q w
Y R
Fig. 4-9
4-33
CHAPTER 4 Adjustment
3-4-1-2
9) Refer to Fig. 4-10 and Table 4-3 and turn the dog ring to the minimum extent. 10) Tighten the M4 bolts to fasten the dog plate. 11) Go out of the safeguard enclosure, and check that no one is inside the safeguard enclosure. Then turn on the controller. 12) Perform the absolute reset from outside the safeguard enclosure. 13) After the absolute reset is completed, read the machine reference value displayed on the MPB/RPB.
4-34
CHAPTER 4 Adjustment
14) If the machine reference value is in the range between 40 and 60 (recommended range), then the machine reference has been completely adjusted. If it is outside the recommended range, then repeat the procedure that starts in 5) to readjust it.
4-35
CHAPTER 4 Adjustment
The method to change the X-axis origin position is as follows. 1) Prepare the necessary tools. Hex wrench set 2) Check that no one is inside the safeguard enclosure and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) Place a sign indicating that the robot is being adjusted in order to keep others from operating the controller or operation panel. 5) Turn off the controller and enter the safeguard enclosure. 6) Use the hex wrench to loosen the two M4 bolts which fasten the dog plate to the X-axis joint area. (See Fig. 4-10.) 7) Move the dog plate to position the sensor detection area (dog) on the dog plate at the desired origin position.
! CAUTION
The upper and lower parts of the dog plate are symmetric. Move the dog plate to position it at the desired origin position.
8) Tighten the M4 bolts to fasten the dog plate. 9) Go out of the safeguard enclosure, and check that no one is inside the safeguard enclosure. Then turn on the controller. 10) Perform the absolute reset from outside the safeguard enclosure. 11) After the absolute reset is completed, read the machine reference value displayed on the MPB/RPB. 12) If the machine reference value is between 40 and 60 (recommended range), then the origin position has been completely changed. If it is outside the recommended range, then adjust the machine reference by referring to "1-1 Adjusting the X-axis machine reference".
4-36
CHAPTER 4 Adjustment
2-1 Adjusting the Y-axis machine reference The adjustment method for the Y-axis machine reference is as follows. 1) Prepare the necessary tools. Hex wrench set 2) Check that no one is inside the safeguard enclosure and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) If any machine reference value displayed on the MPB/RPB is not in the range between 40 and 60 (recommended range) after the absolute reset has been completed, then proceed with the following adjustment procedure. 5) Place a sign indicating that the robot is being adjusted in order to keep others from operating the controller or operation panel. 6) Turn off the controller and enter the safeguard enclosure. 7) Mark off the reference mark at the current origin position on the Y-axis joint area of the robot. At this time, be careful to prevent the origin position from deviating since the Y-axis arm is touched. 8) Use the hex wrench to loosen two setscrews which fasten the dog ring of the Y-axis joint area. (See Fig. 4-10.)
! CAUTION
The collar is placed between the setscrew and Y-axis arm. It is sufficient to loosen the setscrew. It is not necessary to completely remove it.
9) Refer to Fig. 4-10 and Table 4-3 and turn the dog ring to the minimum extent. 10) Tighten the setscrews to fasten the dog ring.
! CAUTION
Depending on the origin position, the dog ring may not be able to be fastened with the two setscrews. In this case, fasten the dog ring with one setscrew.
11) Go out of the safeguard enclosure, and check that no one is inside the safeguard enclosure. Then turn on the controller.
4-37
CHAPTER 4 Adjustment
12) Perform the absolute reset from outside the safeguard enclosure. 13) After the absolute reset is completed, read the machine reference value displayed on the MPB/RPB. 14) If the machine reference value is in the range between 40 and 60 (recommended range), then the machine reference has been completely adjusted. If it is outside the recommended range, then repeat the procedure that starts in 5) to readjust it.
4-38
CHAPTER 4 Adjustment
The method to change the Y-axis origin position is as follows. 1) Prepare the necessary tools. Hex wrench set 2) Check that no one is inside the safeguard enclosure and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) Place a sign indicating that the robot is being adjusted in order to keep others from operating the controller or operation panel. 5) Turn off the controller and enter the safeguard enclosure. 6) Use the hex wrench to loosen two setscrews which fasten the dog ring of the Y-axis joint area. (See Fig. 4-10.)
! CAUTION
The collar is placed between the setscrew and Y-axis arm. It is sufficient to loosen the setscrew. It is not necessary to completely remove it.
7) Turn the dog ring to move the sensor detection area (dog) on the dog ring to the desired origin position. 8) Tighten the setscrews to fasten the dog ring.
! CAUTION
Depending on the origin position, the dog ring may not be able to be fastened with the two setscrews. In this case, fasten the dog ring with one setscrew.
9) Go out of the safeguard enclosure, and check that no one is inside the safeguard enclosure. Then turn on the controller. 10) Perform the absolute reset from outside the safeguard enclosure.
4-39
CHAPTER 4 Adjustment
11) After the absolute reset is completed, read the machine reference value displayed on the MPB/RPB. 12) If the machine reference value is between 40 and 60 (recommended range), then the origin position has been completely changed. If it is outside the recommended range, then adjust the machine reference by referring to "2-1 Adjusting the Y-axis machine reference".
4-40
CHAPTER 4 Adjustment
3-1 Adjusting the R-axis machine reference The adjustment method for the R-axis machine reference is as follows. 1) Prepare the necessary tools. Hex wrench set 2) Check that no one is inside the safeguard enclosure and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) If any machine reference value displayed on the MPB/RPB is not in the range between 40 and 60 (recommended range) after the absolute reset has been completed, then proceed with the following adjustment procedure. 5) Place a sign indicating that the robot is being adjusted in order to keep others from operating the controller or operation panel. 6) Turn off the controller and enter the safeguard enclosure. 7) Mark off the reference mark at the current origin position on the R-axis area of the robot. At this time, be careful not to touch the tool at the tip of the robot arm so that the origin position does not shift. 8) Use the hex wrench to loosen the two M4 bolts which fasten the dog ring on the R-axis area. (See Fig. 4-10.)
! CAUTION
It is sufficient to loosen the M4 bolts. It is not necessary to completely remove them.
9) Refer to Fig. 4-10 and Table 4-3 and turn the dog ring to the minimum extent. 10) Tighten the M4 bolts to fasten the dog ring. 11) Go out of the safeguard enclosure, and check that no one is inside the safeguard enclosure. Then turn on the controller. 12) Perform the absolute reset from outside the safeguard enclosure. 13) After the absolute reset is completed, read the machine reference value displayed on the MPB/RPB. 14) If the machine reference value is in the range between 40 and 60 (recommended range), then the machine reference has been completely adjusted. If it is outside the recommended range, then repeat the procedure that starts in 5) to readjust it.
4-41
CHAPTER 4 Adjustment
3-2 R-axis origin position change The R-axis origin position cannot be changed on the YK500X, YK600X, YK700X, YK800X, and YK1000X.
4-42
CHAPTER 4 Adjustment
X-axis dog plate w q w M4 bolts (2 places) X-axis dog X-axis origin sensor
q w q
Table 4-3
Movement amount (mm) for 100% of machine reference Axis X Y R YK500X, YK600X 1.23 1.17 1.58 YK700X, YK800X, YK1000X 1.63 (YK1000X : 1.31) 1.48 1.71
* Machine reference < 40% : Movement in direction q Machine reference > 60% : Movement in direction w
Y-axis dog Y-axis dog ring Set screw (One each on opposite sides)
Fig. 4-10
4-43
CHAPTER 4 Adjustment
3-4-1-3
YK550X
1 Changing the X-axis origin position and adjusting the machine reference value
1) Prepare the necessary tools. Slotted screwdriver Hex wrench set Plastic hammer 2) Check that no one is inside the safeguard enclosure, and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) Check that return-to-origin is complete. 5) Turn off the controller. 6) Place a sign indicating the robot is being adjusted, to keep others from operating the controller switch. 7) Enter the safeguard enclosure. 8) Remove the cover on the left side of the robot base (pedestal) as viewed from the front and pry off the rubber cap with a slotted screwdriver. The X-axis origin dog and its mounting screw can be seen through the circular adjustment window. (See Fig. 4-11.) 9) Use the 2mm hex wrench to loosen the set screw of the X-axis origin dog (but, do not remove it). 10) With the 2mm hex wrench still inserted into the set screw, move the X-axis arm by hand to the desired origin position. 11) Move the X-axis origin dog so that the set screw is positioned in the center of the adjustment window. At this position the X-axis origin sensor is aligned with the origin dog. 12) Tighten the set screw of the X-axis origin dog.
4-44
CHAPTER 4 Adjustment
Rear cover
Fig. 4-11 X-axis origin dog 13) Go outside the safeguard enclosure, check that no one is inside the safeguard enclosure, and turn on the controller. Then perform absolute reset and check the X-axis origin position when return-to-origin is complete. 14) Check the machine reference value displayed on the MPB/RPB. When it is within the allowable range (between 40 and 60%), the X-axis origin adjustment is now complete. If the machine reference value is outside the allowable range, make a note of the machine reference value and make adjustment with the following procedure. 15) Turn off the controller. 16) Enter the safeguard enclosure. 17) Loosen the set screw and move the X-axis origin dog as indicated in NOTE below. Retighten the set screw, then repeat the above procedure from step 13) until the X-axis machine reference value is set within the allowable range. NOTE Move the origin dog as follows: X-axis machine reference value < 40% : Turn to the left. X-axis machine reference value > 60% : Turn to the right. As an approximate guide, a 1.2mm movement equals 100%. 18) After adjustment is complete, turn off the controller. Then enter the safeguard enclosure, refit the rubber cap by tapping it with a plastic hammer, and reattach the cover.
4-45
CHAPTER 4 Adjustment
Changing the Y-axis origin position and adjusting the machine reference value
1) Prepare the necessary tools. Hex wrench set 2) Check that no one is inside the safeguard enclosure, and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) Check that return-to-origin is complete. 5) Turn off the controller. 6) Place a sign indicating the robot is being adjusted, to keep others from operating the controller switch. 7) Enter the safeguard enclosure. 8) Remove the M16 set screw located on the Y-axis arm joint with the 8mm hex wrench. The Y-axis origin dog and set screw can be seen through the adjustment window. (See Fig. 4-12) 9) Use the 2mm hex wrench to loosen the set screw of the Y-axis origin dog (but, do not remove it). 10) With the 2mm hex wrench still inserted into the set screw, move the Y-axis arm by hand to the desired origin position. 11) Move the Y-axis origin dog so that the set screw is positioned in the center of the adjustment window. At this position the Y-axis origin sensor is aligned with the origin dog. 12) Tighten the set screw of the Y-axis origin dog.
4-46
CHAPTER 4 Adjustment
Left
Adjustment window
Fig. 4-12 Y-axis origin dog 13) Go outside the safeguard enclosure, check that no one is inside the safeguard enclosure, and turn on the controller. Then perform absolute reset and check the Y-axis origin position when return-to-origin is complete. 14) Check the machine reference value displayed on the MPB/RPB. When it is within the allowable range (between 40 and 60%), the Y-axis origin adjustment is now complete. If the machine reference value is outside the allowable range, make a note of the machine reference value and make adjustment with the following procedure. 15) Turn off the controller. 16) Enter the safeguard enclosure. 17) Loosen the set screw and move the Y-axis origin dog as indicated in NOTE below. Retighten the set screw, then repeat the above procedure from step 13) until the Y-axis machine reference value is set within the allowable range. NOTE Move the origin dog as follows: Y-axis machine reference value < 40% : Turn to the right. Y-axis machine reference value > 60% : Turn to the left. As an approximate guide, a 0.8mm movement equals 100%. 18) After adjustment is complete, turn off the controller, then enter the safeguard enclosure and reattach the M16 set screw by tightening it.
4-47
CHAPTER 4 Adjustment
Changing the R-axis origin position and adjusting the machine reference value
The R-axis origin position is fixed and cannot be changed. The R-axis machine reference value is preadjusted before shipment and does not deviate from the allowable range (40 to 60%) during normal operation. However, if for some reason the machine reference value goes outside the allowable range, adjust as needed with the procedure below.
! CAUTION
The origin position may shift if the origin sensor is moved too far.
1) Prepare the necessary tools. Phillips screwdriver Hex wrench set 14mm wrench 2) Check that no one is inside the safeguard enclosure, and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. 4) After return-to-origin is complete, note the R-axis machine reference value displayed on the MPB/RPB. When this value is within the allowable range (40 to 60%), no adjustment is required. If not, adjust as follows. 5) Turn off the controller. 6) Place a sign indicating the robot is being adjusted, to keep others from operating the controller switch. 7) Enter the safeguard enclosure. 8) Remove the cover on the Y-axis arm. (See Fig. 4-21.) Place the cover on the robot pedestal side with the machine harness still connected. The R-axis origin sensor and dog can be seen at the location shown in Figure 4-13.
R-axis origin sensor
CHAPTER 4 Adjustment
9) Put a mark on the current position of the R-axis origin sensor, then loosen the bolts (M4, 1 piece) securing the installation plate of the R-axis origin sensor. (See Fig. 4-14.)
M4 Bolt
Fig. 4-14 Adjusting the R-axis origin sensor 10) Move the R-axis origin sensor as indicated in NOTE below. NOTE Move the origin sensor as follows: R-axis machine reference value < 40% : Move to the right. R-axis machine reference value > 60% : Move to the left. As an approximate guide, a 0.8mm movement equals 100%. (1.3mm/100% for high-speed R-axis specifications) 11) Retighten the bolts to secure the installation plate. Place the 10mm wrench on the flat sides on the spline shaft and turn it to check that the origin sensor does not touch the origin dog. If the origin sensor touches the origin dog, adjust the position of the origin sensor so that they do not interfere with each other. 12) Go outside the safeguard enclosure, check that no one is inside the safeguard enclosure, and turn on the controller. Then perform absolute reset and check the R-axis machine reference value when return-to-origin is complete. 13) Repeat the above steps until the R-axis machine reference value is set within the allowable range. 14) After adjustment is complete, turn off the controller, then enter the safeguard enclosure and reattach the cover to the Y-axis arm.
4-49
CHAPTER 4 Adjustment
3-4-2
Mark method
In the mark method, the origin position can be changed with the absolute reset at the desired position. It is not necessary to adjust the machine reference. Refer to "Chapter 4, 3-3 Absolute reset procedures" for information about the absolute reset method with the mark method.
! CAUTION
If the origin position has been changed, then the absolute reset must be performed and the standard coordinate and point data must be reset.
! CAUTION
Mark off the reference mark at the position where the absolute reset is performed so that the absolute reset position can be easily checked the next time an absolute reset is performed. Unless it can be precisely checked, then the repeatability of the absolute reset position cannot be assured. Refer to "Chapter 4, 3-3 Absolute reset procedures" for information about the absolute reset.
4-50
CHAPTER 4 Adjustment
3-4-3
! CAUTION
The positional shift will occur after adjusting the machine reference value, so point data settings are required again.
3-4-3-1
4-51
CHAPTER 4 Adjustment
8) Remove the bolts securing the Z-axis motor (See Figs. 4-15 to 4-18) and then remove the Z-axis motor. WARNING
If the Z-axis motor comes off the Z-axis belt, the Z-axis drops causing a hazardous situation. Be sure to prop the Z-axis with a support stand.
9) Adjust the distance (L) between the Z-axis mechanical stopper and the axis end so it is set to the value shown in Table 4-4. Then tighten the four bolts to reassemble the Z-axis motor. (See Fig. 4-19, Fig4-20.) At this point, do not allow the spline shaft position to shift from the correct height. 10) After reassembling the Z-axis motor, adjust the timing belt tension. To adjust the timing belt tension, see "8 Adjusting the Timing Belt Tension" in Chapter 4. 11) Reattach the Y-axis upper cover and under cover (YK500X to YK1000X). To attach the covers, see "7 Removing the Robot Covers" in Chapter 4. 12) Go outside the safeguard enclosure. 13) Check that no one is inside the safeguard enclosure, and then turn on the controller.
4-52
CHAPTER 4 Adjustment
14) Perform the Z-axis absolute reset. To perform the Z-axis absolute reset, see "3-3 Absolute reset procedures" in Chapter 4. After absolute reset is complete, use the following procedure to check if the adjustment machine reference value is within the tolerance range (26 and 74).
! CAUTION
The adjustment machine reference value is displayed with the procedure below. Always check the adjustment machine reference value when the machine reference is adjusted.
q w e r
Press the MODE key. Press the F3 key to set MANUAL mode. Press the F13 (LOWER+F3) key to select "RST. ABS ". After the Z-axis absolute reset is complete, press the F10 (UPPER+F5) to display the adjustment machine reference value (%).
If adjustment machine reference value is outside the absolute reset tolerance range (26 to 74), remove the Z-axis motor again and make fine-adjustment to the spline shaft height, so that the adjustment machine reference value is within the absolute reset tolerance range.
Table 4-4
Robot Model YK250X, YK350X, YK400X YK250XH, YK350XH, YK400XH YK500X, YK600X YK700X, YK800X, 1000X YK1200X L 5mm 4mm 8mm 8mm 21mm
4-53
CHAPTER 4 Adjustment
CHAPTER 4 Adjustment
3-4-3-2
YK550X
1) Prepare the necessary tools. Hex wrench set Phillips screwdriver Support stand Ruler 2) Check that no one is inside the safeguard enclosure, and then turn on the controller. 3) Perform the absolute reset from outside the safeguard enclosure. Refer to "3-3 Absolute reset procedures" for information about the absolute reset method. To check the machine reference value, refer to step 14) in section 3-4-3-1. 4) After return-to-origin is complete, check the Z-axis machine reference value displayed on the MPB/RPB. When this value is within the allowable range (40 to 60%), no adjustment is required. If not, adjust as follows. 5) Turn off the controller. 6) Place a sign indicating the robot is being adjusted, to keep others from operating the controller switch. 7) Enter the safeguard enclosure. 8) Remove the screws (7 pieces) securing the upper cover on the Y-axis arm and remove the cover. Place the cover on the robot pedestal side with the machine harness still connected. Also remove the Y-axis arm under covers. 9) Before removing the Z-axis motor, use a support stand to prop the spline or end effector to prevent it from dropping along the Z-axis. Then, remove the four M4 bolts on the Z-axis motor underplate, but do not remove the bolts securing the Z-axis motor. It is unnecessary to remove the Z-axis motor underplate from the arm.
4-55
CHAPTER 4 Adjustment
M4 bolt
plate
Upper cover
Screw
Scribed line
plate
Under cover
Scribed line
Stand
Fig. 4-21
4-56
CHAPTER 4 Adjustment
10) Adjust the height of the support stand so that the distance between the urethane damper and the upper face of the ball screw nut is 12mm as shown in Fig. 422. Then, fit the Z-axis belt on the Z-axis motor pulley. 11) Lightly tighten the bolts to temporarily fasten the Z-axis motor underplate until it has no play in the vertical direction. 12) Viewing from the bottom of the Y-axis arm, check that the belt is properly engaged with the Z-axis motor pulley and ball screw pulley. 13) Pull the Z-axis motor in the direction of arrow and align the scribed lines (on both sides of the X-axis motor underplate) with the reference scribed lines. While maintaining this position, tighten the four M4 bolts to 4.5Nm (46kgfcm) to secure the Z-axis motor underplate.
! CAUTION
If the scribed lines on the Z-axis motor underplate do not reach the reference scribed lines, the belt teeth may slip on the pulley. If they exceed the reference scribe lines on the arm, the Z-axis drive unit may wear out quickly. Align the scribed lines exactly.
14) Go outside the safeguard enclosure, check that no one is inside the safeguard enclosure, and turn on the controller. Then perform absolute reset. 15) Check that the Z-axis machine reference value is within the allowable range (40 to 60%). 16) After adjustment is complete, turn off the controller, then enter the safeguard enclosure and reattach the covers to the Y-axis arm.
4-57
CHAPTER 4 Adjustment
Pull
M4 bolt
Y-axis arm
Spline
Fig. 4-22
4-58
CHAPTER 4 Adjustment
CHAPTER 4 Adjustment
! CAUTION
The origin position factory-adjusted at shipment is not completely aligned with the front face position of the robot. When introducing the robot, be sure to set the soft limits with the number of pulses from the origin position (0 pulse position).
4-60
CHAPTER 4 Adjustment
(2) Setting the Z-axis soft limits Make this setting from outside the safeguard enclosure. The Z-axis has mechanical stoppers fixed at the upper and lower ends of the Z-axis movement range. When the actual working range of the robot is smaller than the maximum working envelope or the manipulator interferes with the peripheral equipment, reduce the Z-axis plus (+) soft limit [pulses] to narrow the working envelope. (3) Setting the R-axis soft limit To make this setting, set emergency stop just as for the X-axis and Y-axis, or be sure to do this from outside the safeguard enclosure. The R-axis has no mechanical stoppers. When the actual working range of the R-axis is small or it interferes with the peripheral equipment, reduce the R axis plus (+) soft limit [pulse] and minus (-) soft limit [pulses] to narrow the working envelope.
! CAUTION
Overloads may occur if the soft limit is almost near the encoder pulse at the mechanical stopper and the operating point is used at the edge of the movement range. Set the soft limit to the inner side of the mechanical stopper with an ample safety margin.
(4) Relation between the X, Y and R-axis movement angle, the Z-axis movement distance and the number of pulses The tables below are for calculating resolver pulses with respect to the X, Y and R-axis movement angles and to the Z-axis movement distance for each robot. Use these figures as a guide to set the soft limits.
X, Y and R-axis speed reduction ratio and Z-axis ball screw lead for each robot Robot model YK250X(H), YK350X(H), YK400X(H) YK500X, YK600X YK700X, YK800X YK1000X YK1200X YK550X YK550X with high-speed R-axis specifications X-axis 50 80 80 100 121 50 50 Y-axis 50 80 80 80 105 50 50 Z-axis 12mm 20mm 20mm 20mm 10mm 30mm 30mm R-axis 50 50 50 50 50 50 30
Operation angle/distance vs. number of resolver pulses X, Y and R-axis speed reduction ratio Speed ratio 30 50 80 100 105 121 Z-axis Lead 10mm 12mm 20mm 30mm Number of resolver pulses per lead movement 16384 16384 16384 16384 Number of resolver pulses per turn (360 degrees) 491520 819200 1310720 1638400 1720320 1982464
4-61
CHAPTER 4 Adjustment
If the standard coordinate settings are incorrect, the acceleration cannot be optimized to match the arm position. This results in too short a service life, damage to the drive unit, or residual vibration during positioning. In addition, the cartesian coordinate accuracy will be impaired.
Setting the standard coordinates enables the following operations and functions. 1. Optimizes acceleration according to arm position during automatic op eration. 2. Allows moving robot arm tip at right angles. 3. Allows using shift coordinates. 4. Enables commands such as linear interpolation and arm switching. The procedure for setting standard coordinates and cautions are shown below. 1) Check that no one is inside the safeguard enclosure, and then turn on the controller. 2) Check that the soft limits are correctly set. If not correctly set, adjust the soft limits while referring to the description of "4 Setting the Soft Limits" in Chapter 4. 3) Place a sign indicating the robot is being adjusted, to keep others from operating the controller or operation panel. 4) Enter the safeguard enclosure while holding the MPB/RPB. Stay outside the robot movement range at this time. 5) Make the standard coordinate settings while referring to methods for "Setting the Standard Coordinates" as explained in the "YAMAHA Robot Controller User's Manual". Never enter within the robot movement range. 6) When the standard coordinate settings are complete, check the following points from outside the safeguard enclosure. 1. Check that the robot arm tip can move at right angles in MANUAL operation (cartesian coordinates). 2. Check that the values nearly equal to the X-axis and Y-axis arm lengths are entered in "Arm length" of the axis parameters. If the above points are not satisfied, the standard coordinate settings are incorrect, so make the standard coordinate settings again.
4-62
CHAPTER 4 Adjustment
Affixing Stickers for Origin Positions, Movement Directions and Axis Names
The robot comes packed with stickers showing origin positions, movement directions and axis names as shown in Fig. 4-23. Using the following procedure, attach these stickers in conspicuous points on the robot after changing the origin position and installing peripheral equipment. 1) Check that no one is inside the safeguard enclosure, and then turn on the controller. 2) Move the robot to the 0 pulse position. To move the axes to their "0" pulse positions, see "Chapter 4 Point trace function" in the "YAMAHA Robot Controller User's Manual". 3) Turn off the controller. 4) Place a sign indicating the robot is being adjusted, to keep others from operating the controller switch. 5) Enter the safeguard enclosure. 6) Being careful not to move the origin positions, attach stickers at conspicuous points on matching sides of components such as the robot arm of each axis, base (robot pedestal) and end effector. Affix stickers nearby showing the axis name and direction of movement. Use a cloth moistened with alcohol to remove grease from the surface where you will affix the stickers. After the surface is dry, affix the stickers securely. (See Fig. 4-24) WARNING
Affix the origin position stickers precisely on the origin positions. Align the direction of movement stickers with the jog direction and affix them correctly. Affix each axis name sticker on the correct axis. Affixing the sticker at a wrong location may cause faulty operation and hazardous situations.
A X Z
(a) Origin position stickers
B Y R
Fig. 4-23
4-63
CHAPTER 4 Adjustment
R +
+ Y +
End effector
4-64
CHAPTER 4 Adjustment
4) Enter the safeguard enclosure. 5) Remove the covers while referring to Fig. 4-25 to Fig. 4-28. Screws used to fasten each cover are listed in Tables 4-5 to 4-8.
Table 4-5 YK250X(H), YK350X(H), YK400X(H) (See Fig. 4-25) Cover name Base (robot pedestal) rear cover Base (robot pedestal) front cover Y-axis arm upper cover Screw No. q w e r t Screw size M46 M46 M36 M310 M316 Qty 4 4 2 2 2
Table 4-6 YK500X, YK600X (See Fig. 4-26) Cover name Base (robot pedestal) rear cover 1 Base (robot pedestal) rear cover 2 Base (robot pedestal) front cover X-axis arm upper cover Y-axis arm upper cover Y-axis arm under cover Screw No. q w e r t y u Screw size M46 M46 M46 M46 M36 M350 M46 Qty 8 4 8 2 4 4 4
Table 4-7 YK700X, YK800X, YK1000X (See Fig. 4-27) Cover name Base (robot pedestal) rear cover 1 Base (robot pedestal) rear cover 2 Base (robot pedestal) front cover X-axis arm upper cover Y-axis arm upper cover Y-axis arm under cover Screw No. q w e r t y u Screw size M46 M46 M46 M48 M46 M450 M46 Qty 8 4 8 2 4 4 4 (6 for YK1000X)
Table 4-8 YK1200X (See Fig. 4-28) Cover name Base (robot pedestal) rear cover 1 Base (robot pedestal) rear cover 2 Base (robot pedestal) front cover X-axis arm upper cover X-axis arm under cover Y-axis arm front cover Y-axis arm side cover Screw No. q w e r t y u Screw size M46 M46 M46 M46 M46 M46 M46 Qty 8 4 4 2 2 14 10
4-65
CHAPTER 4 Adjustment
eM36 (with washer)
rM310
tM316
Fig. 4-25
4-66
CHAPTER 4 Adjustment
tM36 (with washer) rM46
eM46
Y-axis under cover Base rear cover 1 Base front cover yM350 uM46 Base rear cover 2 wM46 qM46
Fig. 4-26
4-67
CHAPTER 4 Adjustment
tM46 (with washer) rM48
eM46
yM450 uM46
qM46
wM46
Fig. 4-27
4-68
CHAPTER 4 Adjustment
eM46
wM46
Fig. 4-28
4-69
CHAPTER 4 Adjustment
WARNING
Injury can occur if hands or fingers are squeezed between the drive pulley and belt. Always turn off the controller and use caution when handling these parts.
! CAUTION
Since a positional shift occurs after adjusting the belt tension, it is necessary to make absolute reset, standard coordinate setting and point data setting again.
Push-pull scale
Slack
Load
Pulley
Belt
Pulley
Belt
25
Push-pull scale
Hole
15
55
CHAPTER 4 Adjustment
8-1
Adjust the Z-axis and R-axis timing belts of the YK250X, YK350X and YK400X with the procedure below. 1) Prepare the necessary tools. Push-pull scale Stay (See Fig. 4-30. This stay should be prepared by the user.) Hex wrench set Phillips-head screwdriver Scale 2) Turn off the controller. 3) Place a sign indicating the robot is being adjusted, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the Y-axis upper cover. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the cover. Place the upper cover on the robot base (pedestal) side with the machine harness still connected. 6) Prop the spline or end effector with a support stand to prevent the Z-axis from dropping (when adjusting the Z-axis belt tension). 7) Adjust the belt tension by two people as follows. Using the push-pull scale, one person applies a load perpendicular to the middle of the belt. The other person checks the slack of the belt. (See Fig. 429 and Fig. 4-30.) 8) The correct load to be applied to the belt of each robot model and the resulting slack are shown in Tables 4-7 and 4-7. When the load producing the specified slack is within this range, no adjustment is required. If not, adjust the tension with the following procedure. (1) Z-axis belt adjustment 1. Loosen the bolt q shown in Fig. 4-31. 2. If the load producing the slack specified in Table 4-9 (step 7) above) is smaller than the specified range, move the Z-axis motor in the direction increasing the tension. If the load is greater than this, move it in the direction reducing the tension. Then, retighten the bolt. 3. Recheck the belt tension using the same procedure in step 7). When the load applied to produce the specified slack is within the specified range of Table 4-9, the adjustment is okay. If not, repeat the above procedure from steps 1 to 3.
4-71
CHAPTER 4 Adjustment
(2) R-axis belt adjustment 1. Loosen the bolt w shown in Fig. 4-31. 2. If the load producing the slack specified in Table 4-10 (step 7) above) is smaller than the specified range, move the R-axis motor in the direction increasing the tension. If the load is greater than this, move it in the direction reducing the tension. Then, retighten the bolt. 3. Recheck the belt tension using the same procedure in step 7). When the load applied to produce the specified slack is within the specified range of Table 4-10, the adjustment is okay. If not, repeat the above procedure from steps 1 to 3. 9) After adjustment is complete, tighten the bolt q or w to the torque specified in Table 4-11. 10) Reattach the upper cover to the Y-axis arm. Refer to "7 Removing the Robot Covers" in Chapter 4 for attaching the cover. 11) Go outside the safeguard enclosure. 12) Check that no one is inside the safeguard enclosure, and then turn on the controller.
1M36
2M36
Tension reduces
Tension increases
4-72
CHAPTER 4 Adjustment
8-2
Adjust the Z-axis and R-axis timing belts of the YK500X and YK600X with the procedure below. 1) Prepare the necessary tools. Push-pull scale Stay (See Fig. 4-30. This stay should be prepared by the user.) Hex wrench set Phillips-head screwdriver Scale 2) Turn off the controller. 3) Place a sign indicating the robot is being adjusted, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the Y-axis upper and under covers. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. Place the upper cover on the robot base (pedestal) side with the machine harness still connected. 6) Prop the spline or end effector with a support stand to prevent the Z-axis from dropping (when adjusting the Z-axis belt tension). 7) Adjust the belt tension by two people as follows. Using the push-pull scale, one person applies a load perpendicular to the middle of the belt. The other person checks the slack of the belt. (See Figs. 429 and 4-30.) 8) The correct load to be applied to the belt of each robot model and the resulting slack are shown in Tables 4-9 and 4-10. When the load producing the specified slack is within this range, no adjustment is required. If not, adjust the tension with the following procedure. (1) Z-axis belt adjustment 1. Loosen the bolt q shown in Fig. 4-32. 2. If the load producing the slack specified in Table 4-9 (step 7) above) is smaller than the specified range, move the Z-axis motor in the direction increasing the tension. If the load is greater than this, move it in the direction reducing the tension. Then, retighten the bolt. 3. Recheck the belt tension using the same procedure in step 7). When the load applied to produce the specified slack is within the specified range of Table 4-9, the adjustment is okay. If not, repeat the above procedure from steps 1 to 3.
4-73
CHAPTER 4 Adjustment
(2) R-axis belt adjustment 1. Loosen the bolt w shown in Fig. 4-32. 2. If the load producing the slack specified in Table 4-10 (step 7) above) is smaller than the specified range, move the R-axis motor in the direction increasing the tension. If the load is greater than this, move it in the direction reducing the tension. Then, retighten the bolt. 3. Recheck the belt tension using the same procedure in step 7). When the load applied to produce the specified slack is within the specified range of Table 4-10, the adjustment is okay. If not, repeat the above procedure from steps 1 to 3. 9) After adjustment is complete, tighten the bolt q or w to the torque specified in Table 4-11. 10) Reattach the upper and under covers to the Y-axis arm. Refer to "7 Removing the Robot Covers" in Chapter 4 for attaching the covers. 11) Go outside the safeguard enclosure. 12) Check that no one is inside the safeguard enclosure, and then turn on the controller.
R-axis belt R-axis motor 2M410 Z-axis motor 1M514
Z-axis belt
Tension reduces
Tension increases
4-74
CHAPTER 4 Adjustment
8-3
Adjust the Z-axis and R-axis timing belts of the YK700X, YK800X and YK1000X with the procedure below. 1) Prepare the necessary tools. Push-pull scale Stay (See Fig. 4-30. This stay should be prepared by the user.) Hex wrench set Phillips-head screwdriver Scale 2) Turn off the controller. 3) Place a sign indicating the robot is being adjusted, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the Y-axis upper and under covers. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. Place the upper cover on the robot base (pedestal) side with the machine harness still connected. 6) Prop the spline or end effector with a support stand to prevent the Z-axis from dropping (when adjusting the Z-axis belt tension). 7) Adjust the belt tension by two people as follows. Using the push-pull scale, one person applies a load perpendicular to the middle of the belt. The other person checks the slack of the belt. (See Figs. 429 and 4-30.) 8) The correct load to be applied to the belt of each robot model and the resulting slack are shown in Tables 4-9 and 4-10. When the load producing the specified slack is within this range, no adjustment is required. If not, adjust the tension with the following procedure. (1) Z-axis belt adjustment 1. Loosen the bolt q shown in Fig. 4-33. 2. If the load producing the slack specified in Table 4-9 (step 7) above) is smaller than the specified range, move the Z-axis motor in the direction increasing the tension. If the load is greater than this, move it in the direction reducing the tension. Then, retighten the bolt. 3. Recheck the belt tension using the same procedure in step 7). When the load applied to produce the specified slack is within the specified range of Table 4-9, the adjustment is okay. If not, repeat the above procedure from steps 1 to 3.
4-75
CHAPTER 4 Adjustment
(2) R-axis belt adjustment 1. Loosen the bolt w shown in Fig. 4-33. 2. If the load producing the slack specified in Table 4-10 (step 7) above) is smaller than the specified range, move the R-axis motor in the direction increasing the tension. If the load is greater than this, move it in the direction reducing the tension. Then, retighten the bolt. 3. Recheck the belt tension using the same procedure in step 7). When the load applied to produce the specified slack is within the specified range of Table 4-10, the adjustment is okay. If not, repeat the above procedure from steps 1 to 3. 9) After adjustment is complete, tighten the bolt q or w to the torque specified in Table 4-11. 10) Reattach the upper and under covers to the Y-axis arm. Refer to "7 Removing the Robot Covers" in Chapter 4 for attaching the covers. 11) Go outside the safeguard enclosure. 12) Check that no one is inside the safeguard enclosure, and then turn on the controller.
R-axis belt 2M415 R-axis motor 1M512 Z-axis motor
Z-axis belt
Tension reduces
Tension increases
4-76
CHAPTER 4 Adjustment
8-4
Adjust the Z-axis and R-axis timing belts of the YK1200X with the procedure below. 1) Prepare the necessary tools. Push-pull scale Stay (See Fig. 4-30. This stay should be prepared by the user.) Hex wrench set Phillips-head screwdriver Scale 2) Turn off the controller. 3) Place a sign indicating the robot is being adjusted, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the Y-axis arm front cover and side cover. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. 6) Remove the bolts (M410L, 4 pieces) and then remove the harness clamp stay from the Y-axis arm. (See Fig. 4-34.) 7) Prop the spline or end effector with a support stand to prevent the Z-axis from dropping (when adjusting the Z-axis belt tension). 8) Adjust the belt tension by two people as follows. Using the push-pull scale, one person applies a load perpendicular to the middle of the belt. The other person checks the slack of the belt. (See Figs. 429 and 4-30.) 9) The correct load to be applied to the belt of each robot model and the resulting slack are shown in Tables 4-9 and 4-10. When the load producing the specified slack is within this range, no adjustment is required. If not, adjust the tension with the following procedure. (1) Z-axis belt adjustment 1. Loosen the bolt q shown in Fig. 4-34. 2. If the load producing the slack specified in Table 4-9 (step 7) above) is smaller than the specified range, move the Z-axis motor in the direction increasing the tension. If the load is greater than this, move it in the direction reducing the tension. Then, retighten the bolt. 3. Recheck the belt tension using the same procedure in step 7). When the load applied to produce the specified slack is within the specified range of Table 4-9, the adjustment is okay. If not, repeat the above procedure from steps 1 to 3.
4-77
CHAPTER 4 Adjustment
(2) R-axis belt adjustment 1. Loosen the bolt w shown in Fig. 4-34. 2. If the load producing the slack specified in Table 4-10 (step 7) above) is smaller than the specified range, move the R-axis motor in the direction increasing the tension. If the load is greater than this, move it in the direction reducing the tension. Then, retighten the bolt. 3. Recheck the belt tension using the same procedure in step 7). When the load applied to produce the specified slack is within the specified range of Table 4-10, the adjustment is okay. If not, repeat the above procedure from steps 1 to 3. 10) After adjustment is complete, tighten the bolt q or w to the torque specified in Table 4-11. 11) Reattach the harness clamp stay to the Y-axis arm. (See Fig. 4-34.) Be careful not to allow the R-axis belt to make contact with the harness clamp stay and harness. 12) Reattach the Y-axis arm front cover and side cover. Refer to "7 Removing the Robot Covers" in Chapter 4 for attaching the covers. 13) Go outside the safeguard enclosure. 14) Check that no one is inside the safeguard enclosure, and then turn on the controller.
R-axis belt M410 harness clamp stay R-axis motor wM620 Z-axis motor qM620
Install the harness clamp stay so that the R-axis belt and the harness do not make contact with each other. Z-axis belt
Tension reduces
Tension increases
4-78
CHAPTER 4 Adjustment
Table 4-9 Z-axis belt specifications Robot model YK250X(H), YK350X(H) YK400X(H) YK500X, YK600X YK700X, YK800X YK1000X YK1200X Load(N) 2.7 to 2.9 2.8 to 3.1 9.5 to 10.1 10.3 to 10.9 10.9 to 11.5 11.7 to 12.6 Load(kgf) 0.28 to 0.30 0.29 to 0.32 0.97 to 1.03 1.05 to 1.11 1.11 to 1.17 1.19 to 1.29 Slack (mm) 0.7 1.4 1.6 2.8 4.4 5.9 (Ref.) Belt vibration frequency(Hz) 430 to 453 215 to 226 213 to 225 121 to 127 76 to 80 66 to 70
Table 4-10 R-axis belt specifications Robot model YK250X(H), YK350X(H) YK400X(H) YK500X, YK600X YK700X, YK800X YK1000X YK1200X Load(N) 1.9 to 2.3 1.9 to 2.3 3.1 to 3.8 3.6 to 7.6 6.7 to 8.0 6.8 to 8.1 Load(kgf) 0.19 to 0.23 0.19 to 0.13 0.32 to 0.39 0.64 to 0.78 0.68 to 0.82 0.69 to 0.83 Slack (mm) 2.1 2.8 1.9 2.7 4.3 6.0 (Ref.) Belt vibration frequency(Hz) 159 to 185 118 to 137 182 to 194 97 to 115 61 to 72 54 to 64
Table 4-11 Tightening torque Robot model YK250X(H), YK350X(H), YK400X(H) YK500X, YK600X Axis Z R Z R YK700X, YK800X,YK1000X Z R YK1200X Z R M6 156 15.3 Bolt size M3 M3 M5 M4 M5 M4 Tightening torque (kgfcm) 20 20 92 46 92 46 Tightening torque (Nm) 2.0 2.0 9.0 4.5 9.0 4.5
4-79
CHAPTER 4 Adjustment
8-5
(1)
1) Prepare the necessary tools. Hex wrench set Phillips screwdriver Support stand 2) Turn off the controller. 3) Place a sign indicating the robot is being adjusted, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the screws (7 pieces) shown in Fig. 4-35 and remove the upper cover. Place the upper cover on the robot pedestal side with the machine harness still connected. Also remove the under cover. 6) Check whether the edge of the Z-axis motor flange is aligned with the scribed lines (on both sides of plate) shown in Fig. 4-36. When exactly aligned, no adjustment is required. If not aligned, make adjustment as follows. 7) Prop the spline or end effector with a support stand to prevent the Z-axis from dropping.(See Fig. 4-36.) 8) Slightly loosen the four M4 bolts on the plate under the Z-axis motor as long as no backlash occurs between the plate and the Y-axis arm. 9) Check from the bottom of the Y-axis arm that the belt is properly engaged with the Z-axis motor pulley and ball screw pulley.
4-80
CHAPTER 4 Adjustment
10) Pull the Z-axis motor in the direction of arrow and align the scribed lines (on both sides of the X-axis motor underplate) with the reference scribed lines. While maintaining this position, tighten the four M4 bolts to 4.5Nm (46kgfcm) to secure the Z-axis motor underplate.
! CAUTION
If the scribed lines on the Z-axis motor underplate do not reach the reference scribed lines, the belt teeth may slip on the pulley. If they exceed the reference scribe lines on the arm, the Z-axis drive unit may wear out quickly. Align the scribed lines exactly.
Upper cover
Screw
Z-axis spline
Under cover
Under cover
Fig. 4-35
4-81
CHAPTER 4 Adjustment
Tension adjust bolt
Pull
M4 bolt
Y-axis arm
Z-axis belt
R-axis belt
Stand
4-82
CHAPTER 4 Adjustment
(2)
8) Check from the top and bottom of the Y-axis arm that the belt is properly engaged with the pulleys on the speed reduction gear unit and spline. 9) Utilizing the tension adjust bolt, pull speed reduction gear unit in the reverse direction of arrow and then move it back. When the unit flange edge is exactly aligned with the scribed line, tighten the four M4 bolts to secure the unit. The tightening torque should be 4.5Nm (46kgfcm). Slightly tighten the tension adjust bolt.
! CAUTION
If the flange edge of the speed reduction gear unit does not reach the scribed line, the belt may slip on the pulleys. If it exceeds the scribed line, the belt is too tight causing the drive parts to wear prematurely. Align the flange edge exactly with the scribed line.
4-83
MEMO
4-84
CHAPTER 5
Periodic Inspecition
1 Overview .................................................................................5-1 2 Precautions .............................................................................5-2 3 Daily Inspection ......................................................................5-3 4 Six-Month Inspection ..............................................................5-5 5 Replacing the Harmonic Drive ................................................5-8
5-1 5-2 Replacement period ......................................................................... 5-8 Basic replacement procedure for harmonic drive and precautions .... 5-10
5-2-1 5-2-2 5-2-3 5-2-4 5-2-5 YK250X(H), YK350X(H), YK400X(H) ............................................ 5-12 YK500X, YK600X .......................................................................... 5-29 YK700X, YK800X, YK1000X ......................................................... 5-44 YK1200X ....................................................................................... 5-60 YK550X with high-speed R-axis specifications: R-axis ................. 5-65
MEMO
Overview
Daily and periodic inspection of the YAMAHA robot is essential in order to ensure safe and efficient operation. This chapter describes the periodic inspection items and procedures for the YAMAHA YK-X series robots. Periodic inspection includes: Daily inspection 6-month inspection Replacement of speed reduction gear (harmonic drive) Replacing the grease for speed reduction gear (harmonic drive) Replacing the grease for RV speed reduction gears Make sure that you thoroughly understand details of the inspection and follow the procedures and precautions explained in this chapter.
5-1
Precautions
(1) Periodic inspection must be performed by or in the presence of personnel who have received the Robot Training given by YAMAHA or YAMAHA dealers. (2) Do not attempt any inspection, adjustment, repair and parts replacement not described in this manual. This work requires specialized technical knowledge and skill, and may also involve work hazards. (3) When inspection is required inside the safeguard enclosure, always turn off the controller and also the external switch board. (4) If the inspection or maintenance procedure calls for operation of the robot, stay outside the safeguard enclosure. (5) Place a sign indicating the robot is being inspected, to keep others from operating the controller switch, programming box or operation panel. (6) Use only the lubricants specified by YAMAHA or YAMAHA dealers. (7) To check the operation after inspection, refer to "6 Trial operation" in Chapter 1.
WARNING
When you need to touch the terminals or connectors on the outside of the controller during inspection, always first turn off the controller power switch and also the power source in order to prevent possible electrical shock. Never touch any internal parts of the controller.
For precautions on handling the controller, refer to the "YAMAHA Robot Controller User's Manual".
5-2
Daily Inspection
The following is an inspection list that must be performed every day before and after operating the robot. (1) Inspection to be performed with the controller turned off 1) Turn off the controller. 2) Place a sign indicating the robot is being inspected, to keep others from operating the controller switch. 3) Enter the safeguard enclosure and check the following points.
Checkpoint Machine harness Robot cable User cable and wiring Procedure Check for scratches, dents and excessive bend and kinks. (If the machine harness or robot cable is damaged, contact YAMAHA dealer.) Check air pressure. Check for air leaks. Check drain. Check air filter for clogging or damage. Check for damage. (If a damage is found, contact YAMAHA dealer.)
Robot exterior
(2) Inspection to be performed with the controller turned on 1) Check that no one is inside the safeguard enclosure, and then turn on the controller. 2) Place a sign indicating the robot is being inspected, to keep others from operating the controller, programming box or operation panel. 3) Check the following points from outside the safeguard enclosure.
Checkpoint Procedure Check if the safeguard enclosure is in place. Check if emergency stop is triggered when the door is opened. Check if warning labels are affixed at the entrance and clearly visible. Press the emergency stop button to check if it works. Check for abnormal movement and excessive vibration and noise. (If any abnormal symptom is found, contact YAMAHA dealer.) Check if the brake works to stop the Z-axis from dropping more than 3mm from the stationary point. (If any abnormal operation is found, contact YAMAHA dealer.)
Safeguard enclosure
*1 Visually check the Z-axis movement when you press the emergency stop button from outside the safeguard enclosure and also when you turn off the controller.
5-3
(3) Adjustment and parts replacement 1) After inspection, if you notice any adjustment or parts replacement is needed, first turn off the controller and then enter the safeguard enclosure to perform the necessary work. After adjustment or replacement is finished, again review the checkpoints outlined in (1) and (2) above. 2) If repair or parts replacement is required for the robot or controller, please contact your YAMAHA dealer. This work requires specialized technical knowledge and skill, so do not attempt it by yourself.
5-4
Six-Month Inspection
Take the following precautions when performing 6-month inspection. WARNING
Injury can occur if hands or fingers are squeezed between the drive pulley and belt. Always turn off the controller and use caution when handling these parts.
WARNING
The Z-axis will slide down when the Z-axis brake is released, causing a hazardous situation. Do not release the brake when lubricating the Z-axis parts.
When lubricating the ball screw, spline shaft and linear busing shaft, observe the following precautions. WARNING
Precautions when handling grease: Inflammation may occur if this gets in the eyes. Before handling the grease, wear your safety goggles to ensure the grease will not come in contact with the eyes. Inflammation may occur if the grease comes into contact with skin. Be sure to wear protective gloves to prevent contact with skin. Do not take orally or eat. (Eating will cause diarrhea and vomiting.) Hands and fingers might be cut when opening the container, so use protective gloves. Keep out of the reach of children. Do not heat the grease or place near an open flame since this could lead to sparks and fires. Emergency Treatment: If this grease gets in the eyes, wash liberally with pure water for about 15 minutes and consult a physician for treatment. If this grease comes in contact with the skin, wash away completely with soap and water. If taken internally, do not induce vomiting but promptly consult a physician for treatment.
WARNING
Disposing of grease and the container: Proper disposal is compulsory under federal, state and local regulations. Take appropriate measures in compliance with legal regulations. Do not pressurize the empty container. Pressurizing may cause the container to rupture. Do not attempt to weld, heat up, drill holes or cut this container. This might cause the container to explode and the remaining materials inside it to ignite.
! CAUTION
Unless grease specified by YAMAHA is used, the service life of the ball screw, ball spline and linear bushing shaft will shorten.
5-5
(1) Inspection to be performed with the controller turned off 1) Turn off the controller. 2) Place a sign showing that the robot is being inspected, to keep others from operating the controller switch. 3) Enter the safeguard enclosure and check the following points.
Checkpoint Manipulator bolts and screws (Only for major bolts and screws exposed externally) Z-axis and R-axis timing belts Detection areas of the origin sensors of the X-axis, Y-axis, and R-axis Controller Check for looseness at each terminal and connector on the panel. (See 4 in Chapter 3.) Every 6 month, lubricate the Z-axis ball screw nut with Grease lubrication of Z-axis ball screw, spline, linear shaft grease gun, and the linear shaft, spline shaft and ball screw shaft by hand after removing the old grease. The specified grease is Alvania No.2 (SHOWA SHELL SEKIYU KK). Z-axis ball spline, ball screw Check for backlash. (If any abnormality is found, contact YAMAHA dealer.) Check belt tension. (See 8 in Chapter 4.) Clean if it is dirty. Check for looseness and tighten if necessary.*1 Procedure
5-6
WARNING
Bodily injury may occur from coming into contact with the fan while it is rotating. When removing the fan cover for inspection, first turn off the controller and make sure the fan has stopped.
1) Check that no one is inside the safeguard enclosure, and then turn on the controller. 2) Place a sign indicating the robot is being inspected, to keep others from operating the controller, programming box or operation panel. 3) Check the following points from outside the safeguard enclosure (except checkpoint marked *1).
Checkpoint Procedure Check if the fan rotates normally. Check if objects blocking the fan are located and remove if any are found. Check for abnormal noise from the rotating fan. If abnormal noise is heard, visually check and remove the cause. If no cause is found, contact YAMAHA dealer. Check for dust on the fan cover. Remove and clean if necessary.
Cooling fan at rear of controller X-axis motor cooling fan inside robot base (pedestal) (YK550X only; see Fig. 5-63) *1
*1 After pressing the emergency stop button, enter the safeguard enclosure and make checks. Place a sign indicating the robot is being inspected, to keep others from operating the controller, programming box or operation panel. (3) Adjustment and parts replacement 1) After inspection, if you notice any adjustment or parts replacement is needed, first turn off the controller and then enter the safeguard enclosure to perform the necessary work. After adjustment or replacement is finished, again review the checkpoints outlined in (1) and (2) above. 2) If repair or parts replacement is required for the robot or controller, please contact your YAMAHA dealer. This work requires specialized technical knowledge and skill, so do not attempt it by yourself.
5-7
5-1
Replacement period
The harmonic drive replacement period is determined by the total number of turns of the wave generator used in the harmonic drive. It is recommended to replace the harmonic drive when the total number of turns has reached 8.4108 (at ambient operating temperatures of 0C to +40C). This means that the replacement period will differ depending on the following operating conditions. If the robot operation duty ratio is high or the robot is operated in environments at higher temperatures, the harmonic drive should be replaced earlier. Replacement period = where n : : N : h : D : 8.4108/(n60hDN) years Number of axis movements per minute Average turn per axis movement Speed reduction ratio Operation time per day Operation days per year
For example, when the robot is used under the following conditions, the replacement period for the X-axis harmonic drive of the YK500X can be calculated as follows. n : : N : h : D : Replacement period = = = 10 0.25 80 24 hours per day 240 days per year 8.4108/(n60hDN) 8.4108/(106024240800.25) 12.2 years
5-8
5-9
5-2
WARNING
Precautions when handling harmonic grease, cleaning oil: Inflammation may occur if they get in the eyes. Before handling them, wear your safety goggles to ensure they will not come in contact with the eyes. Inflammation may occur if they come into contact with skin. Be sure to wear protective gloves to prevent contact with skin. Do not take orally or eat. (Eating will cause diarrhea and vomiting.) Hands and fingers might be cut when opening the container, so use protective gloves. Keep out of the reach of children. Do not heat them or place near an open flame since this could lead to sparks and fires. Emergency Treatment: If they get in the eyes, wash liberally with pure water for about 15 minutes and consult a physician for treatment. If they come in contact with the skin, wash away completely with soap and water. If taken internally, do not induce vomiting but promptly consult a physician for treatment.
WARNING
Disposing of harmonic grease, cleaning oil and the container: Proper disposal is compulsory under federal, state and local regulations. Take appropriate measures in compliance with legal regulations. Do not pressurize the empty container. Pressurizing may cause the container to rupture. Do not attempt to weld, heat up, drill holes or cut this container. This might cause the container to explode and the remaining materials inside it to ignite.
WARNING
When removing the wave generator from the motor shaft or reinstalling it back onto the motor shaft, use caution to avoid as much as possible, applying a thrust load to the motor shaft. If a load is applied, the resolver may be damaged resulting in a hazardous situation of the robot trouble.
5-10
! CAUTION
The harmonic drive service life may shorten if the grease recommended by YAMAHA is not used.
Recommended grease Use the following harmonic drive grease. 4B No.2 (made by Harmonic Drive Systems Inc.)
! CAUTION
Harmonic drive Do not apply strong shocks or impacts to these parts such as with a hammer. Also, do not scratch, scar or dent these parts by dropping, etc. Such actions will damage the harmonic drive. The specified performance cannot be maintained if any part of the harmonic drive is used in a damaged state. This damage or wear may also lead to trouble with the harmonic drive.
! CAUTION
Since a positional shift occurs after replacing the harmonic drive, it is necessary to make absolute reset, standard coordinate setting and point data setting again.
5-11
5-2-1
Cross section diameter: 0.99mm Inner diameter: 53.28mm KN3-M2144-000 Supplied with harmonic drive
2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the base (robot pedestal) front and rear covers. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. WARNING
When you remove the X-axis arm installation bolts (M340L, 8 pieces) in the next step, the X-axis arm may come off causing a hazardous situation. Be especially careful to keep the arm from falling when a heavy tool is attached to the arm tip.
5-12
6) Remove the X-axis arm installation bolts (M340L, 8 pieces). (See Fig. 5-1.)
M340
M614
Fig. 5-1
! CAUTION
An O-ring is fitted to the X-axis arm, so be careful not to let it drop into the peripheral unit. (See Fig. 5-2.)
Fig. 5-2 7) Disconnect the connectors on the X-axis motor power cable XM and resolver cable XP.
5-13
8) Remove the base assembly bolts (M614L, 6 pieces) to separate base 1 and base 2. (See Fig. 5-1 and Fig. 5-3.)
M614 Base 1
M512
Base 2
Fig. 5-3 9) Remove the bolts (M512L, 4 pieces) securing the motor and remove the motor from base 1. (See Fig. 5-4.)
M512
Fig. 5-4
! CAUTION
An O-ring is fitted to the motor, so be careful not to let it drop into the peripheral unit.
5-14
10) Remove the wave generator from the motor shaft. The wave generator is secured with an M3 set screw. (See Fig. 5-6.) 11) Remove the X-axis harmonic drive installation bolts (M320L, 16 pieces)
M320
Fig. 5-5 12) Remove the X-axis harmonic drive from the top of base 1.
! CAUTION
An O-ring is fitted to the X-axis harmonic drive, so be careful not to let it drop into the peripheral unit.
13) Fit an O-ring (supplied with the harmonic drive) coated with harmonic grease into the O-ring groove on the new harmonic drive. Apply small amounts of "Screw Lock" to the bolts (M320L, 16 pieces) and tighten them to secure the harmonic drive from the backside of the base. (See Fig. 5-5.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
5-15
14) Apply harmonic grease to the new wave generator and flexspline. See Fig. 5-6 for applying grease properly.
Fit O-ring (supplied) into this groove Harmonic drive willl be damaged if O-ring is caught out of groove. O-ring : KN3-M2144-000 M3 set screw Apply grease to entire oldham coupling.
O-ring : KN3-M2143-000 Wave generator Apply grease to sufficiently fill in the ball space. Apply grease to the thickness equal to the ball diameter. Circular spline Never remove these temporarily tightened bolts. The axis will otherwise deviate from center.
Fig. 5-6 15) Fit the wave generator onto the motor shaft and fully insert it against the motor. Then, apply small amounts of "Screw Lock" to the M3 set screw (1 piece) you removed earlier and tighten it to secure the wave generator. (See Fig. 5-6.) 16) Fit a new O-ring to the motor and secure the motor to base 1 with the bolts (M512L, 4 pieces) you removed earlier. (See Fig. 5-4.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
17) Fasten base 1 to base 2 with the bolts (M614L, 6 pieces) you removed earlier. (See Fig. 5-3.) 18) Reattach the connectors on the X-axis motor power cable XM and resolver cable XP. 19) Fit a new O-ring into the O-ring groove on the X-axis arm and place the arm on the harmonic drive. Then, apply small amounts of "Screw Lock" to the bolts (M340L, 8 pieces) you removed earlier and tighten them uniformly to secure the X-axis arm to the base. (See Fig. 5-1 and Fig. 5-2.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
5-16
20) Reattach the base (robot pedestal) front and rear covers. 21) Go outside the safeguard enclosure. 22) Check that no one is inside the safeguard enclosure, and then turn on the controller.
! CAUTION
After the Harmonic drive is replaced, an absolute reset must be performed, and the standard coordinate and point data must be reset. Refer to "Chapter 4 Adjustment" to adjust it.
5-17
2. Y-axis 1) Prepare the following tools and items. Harmonic grease 4B No.2 Waste cloth (rag) Phillips-head screwdriver Hex wrench set Screw Lock (thread sealant) Torque-limiting wrench Replacement parts (See table below.)
Replacement parts Parts name Harmonic drive O-ring Type No. SHF-17-50 S63(JIS) YAMAHA Parts No. KN3-M2510-002 KN3-M2519-000 Lower part of harmonic drive For motor Note
Cross section diameter: 0.80mm Inner diameter: 45.40mm KN3-M257L-000 Supplied with harmonic drive
2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the Y-axis arm upper cover. Place the cover on the robot base (pedestal) side with the machine harness still connected. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. WARNING
When you remove the Y-axis arm installation bolts (M320L, 8 pieces) in the next step, the Y-axis arm may come off causing a hazardous situation. Be especially careful to keep the arm from falling when a heavy tool is attached to the arm tip.
5-18
6) Remove the Y-axis arm installation bolts (M320L, 8 pieces). (See Fig. 5-7.)
M320
Fig. 5-7 7) Remove the Y-axis arm and place it where it will not obstruct the work.
! CAUTION
An O-ring is fitted to the upper surface of the harmonic drive, so be careful not to let it drop into the peripheral unit. 8) Remove the wave generator from the motor shaft. The wave generator is secured with an M3 set screws (2 pieces). (See Fig. 5-10.) 9) Remove the Y-axis harmonic drive installation bolts (M340L, 6 pieces)
M340
Fig. 5-8 10) Remove the Y-axis dog ring from the Y-axis Harmonic drive. The dog ring is fastened with M4 setscrews (2 pieces).
5-19
! CAUTION
The dog ring is used for reassembly. Store it where the work will not be disturbed. The dog ring is provided with the setscrews. Be careful to avoid losing them.
11) Remove the Y-axis harmonic drive from the top of the X-axis arm.
! CAUTION
An O-ring is fitted to the X-axis harmonic drive, so be careful not to let it drop into the peripheral unit. (See Fig. 5-9.)
O-ring (S63 : KN3-M2519-000)
Fig. 5-9 12) Remove the four bolts temporarily tightened to the new harmonic drive.
! CAUTION
Remove only the four bolts shown in Fig. 5-10 at this point. Never remove the bolts on the opposite side. If they are removed, the harmonic drive axis may deviate from the center causing trouble.
13) Fit a new O-ring coated with harmonic grease into the O-ring groove on the X-axis arm. (See Fig. 5-9.) 14) Place the new harmonic drive on the X-axis arm, and secure it with the bolts (M340L, 6 pieces). Apply small amounts of "Screw Lock" to the bolts and tighten uniformly them to secure the harmonic drive from the backside. (See Fig. 5-8.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
5-20
15) Fasten the dog ring on the Harmonic drive. 16) Fit an O-ring (supplied with the harmonic drive) coated with harmonic grease into the O-ring groove on the new harmonic drive 17) Apply harmonic grease to the new wave generator and flexspline. See Fig. 5-10 for applying grease properly. 18) Fit the wave generator onto the motor shaft and fully insert it against the motor. Then, apply small amounts of "Screw Lock" to the M3 set screw (2 piece) you removed earlier and tighten it to secure the wave generator. (See Fig. 5-10.)
Circular spline Remove the temporarily tightened bolts when assembling Keep the circular spline from coming off when assembling Fit O-ring (supplied) into this groove Harmonic drive will be damaged if O-ring is caught out of groove. O-ring : KN3-M257L-000 Apply grease to entire oldham coupling. Wave generator O-ring : KN3-M257K-000
Y-axis arm Apply grease to sufficiently fill in the ball space. Never remove these temporarily tightened bolts. The axis will otherwise deviate from center. M3 set screw Apply grease to the thickness equal to the ball diameter.
Fig. 5-10 19) Secure the Y-axis arm to the harmonic drive with the bolts (M320L, 8 pieces) you removed earlier. Apply small amounts of "Screw Lock" to the bolts and tighten them uniformly to secure the Y-axis arm. (See Fig. 5-7.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove. When reassembling the harmonic drive, be careful to keep the circular spline from coming off. If it comes off, the harmonic drive axis will deviate from the center causing trouble.
5-21
20) Reattach the Y-axis arm upper cover. 21) Go outside the safeguard enclosure. 22) Check that no one is inside the safeguard enclosure, and then turn on the controller.
! CAUTION
After the Harmonic drive is replaced, an absolute reset must be performed, and the standard coordinate and point data must be reset. Refer to "Chapter 4 Adjustment" to adjust it.
5-22
3. R-axis 1) Prepare the following tools and items. Harmonic grease 4B No.2 Waste cloth (rag) Phillips-head screwdriver Hex wrench set Screw Lock (thread sealant) Torque-limiting wrench Adjustable wrench or spanner Replacement parts (See table below.)
Replacement parts Parts name Harmonic drive O-ring Edge seal Type No. SHF-14-50 S53(JIS) YAMAHA Parts No. KN3-M1821-001 KN3-M1895-000 Lower part of harmonic drive For wave generator Note
Cross section diameter: 0.80mm Inner diameter: 23.70mm KN3-M181H-000 VR18A KN3-M1886-000
Cross section diameter: 0.60mm Inner diameter: 37.10mm KN5-M181G-000 Supplied with harmonic drive
2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the Y-axis arm upper cover. Place the cover on the robot base (pedestal) side with the machine harness still connected. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. 6) Remove the bolts (M48L, 4 pieces) securing the bearing to the upper end of the spline and remove the spline mount plate, spline and bearing from the holder. (See Fig. 5-11.)
M48
Bearing
Holder
Spline shaft
Fig. 5-11
5-23
WARNING
The Z-axis will slide down when the U-nut is removed in the next step, causing a hazardous situation. Prop the Z-axis with a support stand before loosening the U-nut.
7) While placing a steel rod or similar tool through the 5mm diameter hole at the lower part of the spline, loosen the U-nut at the top of the spline with the wrench, and remove the bearing. (See Fig. 5-12.) Use a round steel rod with a diameter slightly smaller than 5mm. Avoid using a square rod because the spline might be damaged by the edge of the rod. After removing the bearing, refit the U-nut to the top of the spline shaft to keep the spline shaft from falling out.
U-nut
Spline shaft
Spline nut
Fig. 5-12 8) Remove the button bolts (M320L, 6 pieces) on the underside of the Y-axis arm and remove the plate fastening the spline and the harmonic drive. (See Fig. 5-13.)
M320, Button bolt
Fig. 5-13
5-24
! CAUTION
An O-ring is fitted to the fastening plate, so be careful not to let it drop into the peripheral unit. (See Fig. 5-14.)
O-ring (S53 : KN3-M1895-000)
Fig. 5-14 9) Remove the R-axis dog ring from the R-axis Harmonic drive. The dog ring is fastened with M4 setscrews (2 pieces).
! CAUTION
The dog ring is used for reassembly. Store it where the work will not be disturbed. The dog ring is provided with the setscrews. Be careful to avoid losing them.
10) Remove the bolts (M36L, 3 pieces) securing the R-axis motor plate at the top of the Y-axis arm. (See Fig. 5-15.)
M36
Pulley
Fig. 5-15
5-25
11) Loosen the pulley set screw (M4, 2 pieces) and remove the pulley from the wave generator. (See Fig. 5-15.) 12) Remove the harmonic drive installation bolts (M318L, 8 pieces) and pull out the harmonic drive from the bottom of the Y-axis arm. (See Fig. 5-15.)
! CAUTION
An O-ring is fitted to the harmonic drive, so be careful not to let it drop into the peripheral unit.
13) Remove the retaining ring for the wave generator and pull out the wave generator from the bottom of the Y-axis arm. (See Fig. 5-16.) 14) Apply harmonic grease to the new wave generator. See Fig. 5-16 for applying grease properly. 15) Fit a new O-ring into the O-ring groove on the wave generator. (See Fig. 5-16.)
Wave generator Apply grease to sufficiently fill in the ball space. Fit O-ring (supplied) into this groove Harmonic drive will be damaged if O-ring is caught out of groove. O-ring : KN5-M181G-000 Remove the temporarily tightened bolts when assembling Keep the circular spline from coming off when assembling Retaining ring groove Fit a new O-ring into the O-ring groove on the wave generator. O-ring : KN3-M181H-000 Apply grease to entire oldham coupling.
Apply grease to the thickness equal to the ball diameter. Circular spline
Never remove these temporarily tightened bolts. The axis will otherwise deviate from center.
Fig. 5-16 16) Insert the new wave generator into the Y-axis arm from the bottom, and secure it with the retaining ring. The chamfered side of the retaining ring should face downwards.
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
17) Apply harmonic grease to the circular spline. See Fig. 5-16 for applying grease properly.
5-26
18) Remove the four bolts temporarily tightened to the new harmonic drive.
! CAUTION
Remove only the four bolts shown in Fig. 5-16 at this point. Never remove the bolts on the opposite side. If they are removed, the harmonic drive axis may deviate from the center causing trouble.
19) Fit an O-ring (supplied with the harmonic drive) coated with harmonic grease into the O-ring groove on the new harmonic drive. Apply small amounts of "Screw Lock" to the bolts (M318L, 8 pieces) and tighten them to secure the harmonic drive to the Y-axis arm from the top of the Y-axis arm.
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove. When reassembling the harmonic drive, be careful to keep the circular spline from coming off. If it comes off, the harmonic drive axis will deviate from the center causing trouble.
20) Apply small amounts of "Screw Lock" to the M4 set screws (2 pieces) and tighten them to secure the pulley to the wave generator. 21) Check that the timing belt is fitted on the wave generator pulley and motor pulley, and then secure the motor plate. (See Fig. 5-15.)
! CAUTION
It is necessary to apply correct tension to the timing belt during reassembly. Refer to "8 Adjusting the Timing Belt Tension" in Chapter 4.
22) Fasten the dog ring on the Harmonic drive. 23) Next, secure the fastening plate to the harmonic drive with the button bolts (M320L, 6 pieces) coated with small amounts of "Screw Lock". (See Fig. 5-17.) At this point, be careful to keep the spline shaft from coming off the spline nut.
! CAUTION
The harmonic drive service life may shorten if the edge seal effect is insufficient, so carefully reassemble the parts.
5-27
Spline nut
Spline shaft
Fig. 5-17 24) Insert the spline into the holder, fit the bearing onto the spline and tighten the U-nut to secure the bearing. (Utilize the 5 through-hole when tightening the U-nut like you did to loosen it.) (See Fig. 5-11 and Fig. 5-12.) 25) Attach the bearing mount plate to the holder and fasten them with the bolts you removed earlier (M48L, 4 pieces). 26) Reattach the Y-axis arm upper cover. 27) Go outside the safeguard enclosure. 28) Check that no one is inside the safeguard enclosure, and then turn on the controller.
! CAUTION
After the Harmonic drive is replaced, the absolute reset must be performed, and the point data must be reset. Refer to "Chapter 4 Adjustment" to adjust it.
5-28
5-2-2
YK500X, YK600X
The following steps describe procedures and precautions when replacing the harmonic drives of the YK500X and YK600X. (The illustrations show the YK500X). For the bolt tightening torques in this work, refer to Table 5-2. 1. X-axis 1) Prepare the following tools and items. Harmonic grease 4B No.2 Waste cloth (rag) Phillips-head screwdriver Hex wrench set Screw Lock (thread sealant) Ratchet handle Hexagonal socket set Extension bar Torque-limiting wrench Replacement parts (See table below.)
Replacement parts Parts name Harmonic drive Type No. SHF-25-80 S90(JIS) O-ring YAMAHA Parts No. KN4-M2110-001 KN4-M2143-000 Top of harmonic drive Base (robot pedestal) Motor Note
Cross section diameter: 1.78mm Inner diameter: 85.00mm KN4-M2159-000 Cross section diameter: 1.78mm Inner diameter: 69.57mm KN5-M2143-000
Cross section diameter: 1.30mm Inner diameter: 66.50mm KN5-M257L-000 Supplied with harmonic drive
2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the base (robot pedestal) front and rear covers and the X-axis arm upper cover. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. 6) Disconnect the connectors on the X-axis motor power cable XM and resolver cable XP.
5-29
7) Remove the bolts (M620L, 4 pieces) securing the motor holder by using the ratchet handle, M6 hexagonal socket, socket adapter and extension bar. (See Fig. 5-18.)
M614 M620
Fig. 5-18 8) With the motor still attached to the motor holder, pull out the motor by swaying it gently right and left. If it is difficult to remove the motor holder, slowly rotate the X-axis arm and again try removing the motor holder.
! CAUTION
Carefully remove the motor holder so as not to let hands or fingers get pinched between the motor holder and the base. An O-ring is fitted to the motor holder, so be careful not to let it drop into the peripheral unit.
9) Remove the bolts (M614L, 4 pieces) securing the motor and remove the motor from the motor holder. (See Fig. 5-18.)
! CAUTION
An O-ring is fitted to the motor, so be careful not to let it drop into the peripheral unit.
10) Remove the wave generator from the motor shaft. The wave generator is secured with an M4 set screw and key. (See Fig. 5-22.)
! CAUTION
A spacer is inserted between the wave generator and the motor, so be careful not to lose it.
5-30
WARNING
When you remove the X-axis arm installation bolts (M440L, 8 pieces) in the next step, the X-axis arm may come off causing a hazardous situation. Be especially careful to keep the arm from falling when a heavy tool is attached to the arm tip.
WARNING
Removing the X-axis arm is dangerous for just one person. Always use two or more people, or remove the Y-axis arm in advance. Refer to "2. Y-axis" of "5-2-2" for removing the Y-axis arm.
11) Remove the X-axis arm installation bolts (M440L, 8 pieces). (See Fig. 519.)
M440
Fig. 5-19 12) Remove the X-axis arm and place it where it will not obstruct the work.
! CAUTION
An O-ring is fitted to the X-axis arm, so be careful not to let it drop into the peripheral unit. (See Fig. 5-20.)
O-ring (S90 : KN4-M2143-000)
Fig. 5-20
5-31
13) Remove the bolts (M420L, 12 pieces) securing the X-axis harmonic drive. (See Fig. 5-21.)
M420
Fig. 5-21 14) Remove the X-axis harmonic drive from the top of the base.
! CAUTION
An O-ring is fitted to the X-axis harmonic drive, so be careful not to let it drop into the base or peripheral unit.
15) Fit an O-ring (supplied with the harmonic drive) coated with harmonic grease into the O-ring groove on the new harmonic drive. (See Fig. 5-22.) Apply small amounts of "Screw Lock" to the bolts (M420L, 12 pieces) and tighten them to secure the harmonic drive from the backside of the base. (See Fig. 5-21.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
16) Apply harmonic grease to the new wave generator and flexspline. See Fig. 5-22 for applying grease properly. 17) Fit a new O-ring into the O-ring groove on the X-axis arm (see Fig. 5-20) and secure it to the harmonic drive. Then apply small amounts of "Screw Lock" to the bolts (M440L, 8 pieces) you removed earlier and tighten them uniformly to secure the X-axis arm. (See Fig. 5-19.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
5-32
18) Fit the spacer and wave generator onto the motor shaft, and fully insert them against the motor. Then, apply small amounts of "Screw Lock" to the M4 set screw (1 piece) you removed earlier and tighten it to secure the wave generator onto the motor shaft. (See Fig. 5-22.)
Fit O-ring (supplied) into this groove Harmonic drive will be damaged if O-ring is caught out of groove. O-ring : KN5-M257L-000 Apply grease to entire oldham coupling. O-ring : KN5-M2143-000 M4 set screw Spacer
Wave generator Apply grease to sufficiently fill in the ball space. Apply grease to the thickness equal to the ball diameter. Circular spline Never remove these temporarily tightened bolts. The axis will otherwise deviate from center.
Fig. 5-22 19) Fit the O-ring to the motor and secure the motor to the motor holder with the bolts (M614L, 4 pieces) you removed earlier. (See Fig. 5-18 and Fig. 5-22.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
20) Fit a new O-ring coated with harmonic grease into the O-ring groove on the motor holder and tighten the bolts (M620L, 4 pieces) you removed earlier to temporarily secure the motor holder to the base. (See Fig. 5-18.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
21) Uniformly tighten the four bolts (M620L) temporarily fastened in the previous step while moving the X-axis by hand slowly left and right through 45. If any jamming or catching is felt while moving the axis at this time, then reassemble from the beginning. 22) Reattach the connectors on the X-axis motor power cable XM and resolver cable XP. 23) Reattach the base (robot pedestal) front and rear covers and the X-axis arm upper cover.
5-33
24) Go outside the safeguard enclosure. 25) Check that no one is inside the safeguard enclosure, and then turn on the controller.
! CAUTION
After the Harmonic drive is replaced, an absolute reset must be performed, and the standard coordinate and point data must be reset. Refer to "Chapter 4 Adjustment" to adjust it.
5-34
2. Y-axis 1) Prepare the following tools and items. Harmonic grease 4B No.2 Waste cloth (rag) Phillips-head screwdriver Hex wrench set Screw Lock (thread sealant) Torque-limiting wrench Replacement parts (See table below.)
Replacement parts Parts name Harmonic drive O-ring Type No. SHF-20-80 YAMAHA Parts No. KN4-M2510-001 For motor Note
Cross section diameter: 1.78mm Inner diameter: 72.75mm KN4-M257K-000 Lower part of harmonic drive Cross section diameter: 1.50mm Inner diameter: 49.00mm KN3-M2143-000 Cross section diameter: 0.99mm Inner diameter: 53.28mm KN3-M2144-000 Supplied with harmonic drive
2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the Y-axis arm upper cover. Place the cover on the robot base (pedestal) side with the machine harness still connected. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. 6) Disconnect the connectors on the Y-axis motor power cable YM and resolver cable YP. 7) Remove the Y-axis motor installation bolts (M514L, 4 pieces) and then remove the Y-axis motor by swaying it gently right and left. (See Fig. 5-23.)
M514
Fig. 5-23
! CAUTION
An O-ring is fitted to the motor, so be careful not to let it drop into the peripheral unit.
5-35
8) Remove the wave generator from the motor shaft. The wave generator is secured with an M4 set screws. (See Fig. 5-27.) WARNING
When you remove the Y-axis arm installation bolts (M320L, 12 pieces) in the next step, the Y-axis arm may come off causing a hazardous situation. Be especially careful to keep the arm from falling when a heavy tool is attached to the arm tip.
9) Remove the Y-axis arm installation bolts (M320L, 12 pieces). (See Fig. 524.)
M320
Fig. 5-24 10) Remove the Y-axis arm and place it where it will not obstruct the work.
! CAUTION
An O-ring is fitted to the upper surface of the harmonic drive, so be careful not to let it drop into the peripheral unit.
11) Remove the Y-axis harmonic drive installation bolts (M340L, 8 pieces) from the bottom of the arm. (See Fig. 5-25.)
M340
Fig. 5-25 12) Remove the Y-axis harmonic drive from the top of the X-axis arm.
5-36
! CAUTION
An O-ring is fitted to the upper surface of the X-axis, so be careful not to let it drop into the peripheral unit. (See Fig. 5-26.)
O-ring (KN4-M257K-000)
Fig. 5-26 13) Fit a new O-ring coated with harmonic grease into the O-ring groove on the X-axis arm. (See Fig. 5-26.) 14) Place the new harmonic drive on the X-axis arm, and secure it with the bolts (M340L, 8 pieces) you removed earlier. Apply small amounts of "Screw Lock" to the bolts and tighten them uniformly to secure the harmonic drive from the backside. (See Fig. 5-25.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
15) Fit an O-ring (supplied with the harmonic drive) coated with harmonic grease into the O-ring groove on the new harmonic drive. (See Fig. 5-27.) 16) Secure the Y-axis arm to the harmonic drive with the bolts (M320L, 12 pieces) you removed earlier. Apply small amounts of "Screw Lock" to the bolts and tighten them uniformly to secure the Y-axis arm. (See Fig. 5-24.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
5-37
17) Apply harmonic grease to the new wave generator and flexspline. See Fig. 5-27 for applying grease properly. 18) Fit the wave generator onto the motor shaft, and fully insert it against the motor. Then, apply small amounts of "Screw Lock" to the M4 set screw (1 piece) you removed earlier and tighten it to secure the wave generator. (See Fig. 5-27.)
Fit O-ring (supplied) into this groove Harmonic drive will be damaged if O-ring is caught out of groove. O-ring : KN3-M2144-000 M4 set screw Apply grease to entire oldham coupling. O-ring : KN3-M2143-000
Wave generator Apply grease to sufficiently fill in the ball space. Apply grease to the thickness equal to the ball diameter. Circular spline Never remove these temporarily tightened bolts. The axis will otherwise deviate from center.
Fig. 5-27 19) Fit a new O-ring to the motor and tighten the bolts (M514L, 4 pieces) you removed earlier to temporarily secure the motor to the Y-axis arm. (See Fig. 5-23 and Fig. 5-27.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of groove.
20) Uniformly tighten the four bolts (M512L) temporarily fastened in the previous step while moving the Y-axis by hand slowly left and right through 45. If any jamming or catching is felt while moving the axis at this time, then reassemble from the beginning. 21) Reattach the connectors on the Y-axis motor power cable YM and resolver cable YP. 22) Reattach the Y-axis arm upper cover. 23) Go outside the safeguard enclosure. 24) Check that no one is inside the safeguard enclosure, and then turn on the controller.
! CAUTION
After the Harmonic drive is replaced, an absolute reset must be performed, and the standard coordinate and point data must be reset. Refer to "Chapter 4 Adjustment" to adjust it.
5-38
3. R-axis 1) Prepare the following tools and items. Harmonic grease 4B No.2 Waste cloth (rag) Phillips-head screwdriver Hex wrench set Screw Lock (thread sealant) Torque-limiting wrench Hook wrench Replacement parts (See table below.)
Replacement parts Parts name Harmonic drive O-ring Edge seal Type No. SHF-17-50 YAMAHA Parts No. KN4-M1821-000 Note
Cross section diameter: 1.78mm Inner diameter: 63.22mm KN4-M1896-000 Lower part of harmonic drive Cross section diameter: 0.80mm Inner diameter: 45.40mm KN3-M257L-000 Supplied with harmonic drive VR22A KN4-M1886-000
2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the Y-axis arm upper cover. Place the cover on the robot base (pedestal) side with the machine harness still connected. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. WARNING
The Z-axis will slide down when the spline mounting bolts (M516L, 4 pieces) are removed in the next step, causing a hazardous situation. Prop the Z-axis with a support stand before loosening these bolts.
6) Remove the bolts (M516L, 4 pieces) securing the bearing to the upper end of the spline and remove the spline and bearing from the holder. (See Fig. 528.)
Holder
Bearing
M516
Spline shaft
Fig. 5-28
5-39
7) While placing a steel rod or similar tool through the 7mm diameter hole at the lower part of the spline, loosen the U-nut at the top of the spline with the wrench, and remove the bearing and bearing mount plate. (See Fig. 5-29.) Use a round steel rod with a diameter slightly smaller than 7mm. Avoid using a square rod because the spline might be damaged by the edge of the rod. At this point, be careful to keep the spline shaft from coming off the spline nut.
U-nut
Fig. 5-29 8) Remove the bolts (M310L,12 pieces) on the lower side of the Y-axis arm, and remove the R-axis dog ring from the fastening plate. 9) Remove the bolts (M325L, 8 pieces) on the underside of the Y-axis arm and remove the plate fastening the spline and the harmonic drive. (See Fig. 5-30.)
M325
Fastening plate
Fig. 5-30
5-40
! CAUTION
An O-ring is fitted to the fastening plate, so be careful not to let it drop into the peripheral unit. (See Fig. 5-31.)
O-ring : KN4-M1896-000
Fig. 5-31 10) Remove the bolts (M410L, 4 pieces) securing the R-axis motor plate at the top of the Y-axis arm. (See Fig. 5-32.) 11) Loosen the pulley set screw (M4, 2 pieces) and remove the pulley from the wave generator. (See Fig. 5-32.) 12) Remove the harmonic drive installation bolts (M316L, 9 pieces) and pull out the harmonic drive from the bottom of the Y-axis arm. (See Fig. 5-32.)
M316 M4 set screw M410
Pulley
Fig. 5-32
! CAUTION
An O-ring is fitted to the harmonic drive, so be careful not to let it drop into the peripheral unit.
13) Remove the retaining ring for the wave generator and pull out the wave generator from the bottom of the Y-axis arm.
5-41
14) Apply harmonic grease to the new wave generator. See Fig. 5-33 for applying grease properly.
Wave generator Apply grease to sufficiently fill in the ball space. Fit O-ring (supplied) into this groove Harmonic drive will be damaged if O-ring is caught out of groove. O-ring : KN3-M257L-000 Remove the temporarily tightened bolts when assembling Keep the circular spline from coming off when assembling Retaining ring groove
Apply grease to entire oldham coupling. Apply grease to the thickness equal to the ball diameter. Circular spline
Never remove these temporarily tightened bolts. The axis will otherwise deviate from center.
Fig. 5-33 15) Insert the new wave generator into the Y-axis arm from the bottom, and secure it with the retaining ring. The chamfered side of the retaining ring should face downwards. 16) Apply harmonic grease to the circular spline. See Fig. 5-33 for applying grease properly. 17) Remove the four bolts temporarily tightened to the new harmonic drive.
! CAUTION
Remove only the four bolts shown in Fig. 5-33 at this point. Never remove the bolts on the opposite side. If they are removed, the harmonic drive axis may deviate from the center causing trouble.
18) Fit an O-ring (supplied with the harmonic drive) coated with harmonic grease into the O-ring groove on the new harmonic drive. (See Fig. 5-33.) Apply small amounts of "Screw Lock" to the bolts (M316L, 9 pieces) and tighten them to secure the harmonic drive to the Y-axis arm from the top of the Y-axis arm. (See Fig. 5-32.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove. When reassembling the harmonic drive, be careful to keep the circular spline from coming off. If it comes off, the harmonic drive axis will deviate from the center causing trouble.
19) Apply small amounts of "Screw Lock" to the M4 set screws (2 pieces) and tighten them to secure the pulley to the wave generator. (See Fig. 5-32.) 20) Fit the timing belt onto the wave generator pulley and motor pulley, and then secure the motor plate. (See Fig. 5-32.)
5-42
! CAUTION
It is necessary to apply correct tension to the timing belt during reassembly. Refer to "8 Adjusting the Timing Belt Tension" in Chapter 4.
21) Fit a new O-ring into the O-ring groove on the fastening plate and also replace the edge seal with new one. Then secure the fastening plate to the harmonic drive with the bolts (M325L, 8 pieces) coated with small amounts of "Screw Lock". (See Fig. 5-30 and Fig. 5-34.) At this point, be careful to keep the spline shaft from coming off the spline nut.
! CAUTION
The harmonic drive service life may shorten if the edge seal effect is insufficient, so carefully reassemble the parts.
22) Tighten the bolts (M310L, 12 pieces) to secure the dog ring to the fastening plate. 23) Insert the bearing mount plate and bearing onto the spline from the top, and tighten the U-nut to secure the bearing. (Utilize the 7 through-hole when tightening the U-nut like you did to loosen it.) (See Fig. 5-29.) 24) Insert the spline and bearing through the holder and secure them with the bolts you removed earlier (M516L, 4 pieces). (See Fig. 5-28.) 25) Reattach the Y-axis arm upper cover. 26) Go outside the safeguard enclosure. 27) Check that no one is inside the safeguard enclosure, and then turn on the controller.
! CAUTION
After the Harmonic drive is replaced, the absolute reset must be performed, and the point data must be reset. Refer to "Chapter 4 Adjustment" to adjust it.
Edge seal O-ring : KN4-M1896-000 Fastening plate
Spline nut
Spline shaft
Fig. 5-34
5-43
5-2-3
Cross section diameter: 1.78mm Inner diameter: 78.97mm KN5-M2144-000 Cross section diameter: 1.78mm Inner diameter: 69.57mm KN5-M2143-000
Cross section diameter: 1.50mm Inner diameter: 87.50mm KN5-M2199-000 Supplied with harmonic drive
2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the base (robot pedestal) front and rear covers and the X-axis arm upper cover. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. 6) Disconnect the connectors on the X-axis motor power cable XM and resolver cable XP.
5-44
7) Remove the bolts (M620L, 4 pieces) securing the motor by using the ratchet handle, M6 hexagonal socket, socket adapter and extension bar. (See Fig. 535.)
M525 M620
Spacer
Fig. 5-35 8) Slowly pull out the motor while holding it slantways. (See Fig. 5-36.) If it is difficult to remove the motor, slowly rotate the X-axis arm and again try removing the motor.
! CAUTION
Carefully remove the motor so as not to let hands or fingers get pinched between the motor and the base. An O-ring is fitted to the motor and the spacer, so be careful not to let it drop into the peripheral unit.
Fig. 5-36
5-45
9) Remove the wave generator from the motor shaft. The wave generator is secured with an M4 set screw and key. (See Fig. 5-40.) WARNING
When you remove the X-axis arm installation bolts (M555L, 8 pieces) in the next step, the X-axis arm may come off causing a hazardous situation. Be especially careful to keep the arm from falling when a heavy tool is attached to the arm tip.
WARNING
Removing the X-axis arm is dangerous for just one person. Always use two or more people, or remove the Y-axis arm in advance. Refer to "2. Y-axis" of "5-2-3" for removing the Y-axis arm.
10) Remove the X-axis arm installation bolts (M555L, 8 pieces). (See Fig. 537.)
M555
Fig. 5-37 11) Remove the X-axis arm and place it where it will not obstruct the work.
5-46
! CAUTION
An O-ring is fitted to the X-axis arm, so be careful not to let it drop into the peripheral unit. (See Fig. 5-38.)
O-ring (S115 : KN5-M2159-000)
Fig. 5-38 12) Remove the bolts (M525L 8 pieces and M535L 8 pieces) securing the Xaxis harmonic drive. (See Fig. 5-39.)
M525 M535
Fig. 5-39 13) Remove the X-axis harmonic drive from the top of the base.
! CAUTION
An O-ring is fitted to the X-axis harmonic drive, so be careful not to let it drop into the base or peripheral unit.
5-47
14) Fit an O-ring (supplied with the harmonic drive) coated with harmonic grease into the O-ring groove on the new harmonic drive. (See Fig. 5-40.) Apply small amounts of "Screw Lock" to the bolts (M525L 8 pieces and M535L 8 pieces) and tighten them to secure the harmonic drive from the backside of the base. (See Fig. 5-39.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
15) Apply harmonic grease to the new wave generator and flexspline. See Fig. 5-40 for applying grease properly. 16) Fit a new O-ring into the O-ring groove on the X-axis arm and secure it to the harmonic drive. Then apply small amounts of "Screw Lock" to the bolts (M555L, 8 pieces) you removed earlier and tighten them uniformly to secure the X-axis arm. (See Fig. 5-37 and Fig. 5-38.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
17) Fit the wave generator onto the motor shaft, and fully insert it against the motor. Then, apply small amounts of "Screw Lock" to the M4 set screw (1 piece) you removed earlier and tighten it to secure the wave generator onto the motor shaft. (See Fig. 5-40.)
Fit O-ring (supplied) into this groove Harmonic drive will be damaged if O-ring is caught out of groove. O-ring : KN5-M2199-000 Apply grease to entire oldham coupling. O-ring : KN5-M2143-000
M4 set screw
Wave generator Apply grease to sufficiently fill in the ball space. Apply grease to the thickness equal to the ball diameter. Never remove these temporarily tightened bolts. The axis will otherwise deviate from center.
Fig. 5-40
5-48
18) Fit a new O-ring to the motor and temporarily fasten the motor and spacer to the base with the bolts (M620L, 4 pieces) you removed earlier. Insert a new O-ring between the spacer and the base at this point. Insert the motor with the wave generator into the harmonic drive while holding the motor slantways. If it is difficult to insert the motor, try inserting it again while slowly rotating the X-axis arm. (See Fig. 5-36.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
19) Uniformly tighten the four bolts (M620L) temporarily fastened in the previous step while moving the X-axis by hand slowly left and right through 45. If any jamming or catching is felt while moving the axis at this time, then reassemble from the beginning. 20) Reattach the connectors on the X-axis motor power cable XM and resolver cable XP. 21) Reattach the base (robot pedestal) front and rear covers and the X-axis arm upper cover. 22) Go outside the safeguard enclosure. 23) Check that no one is inside the safeguard enclosure, and then turn on the controller.
! CAUTION
After the Harmonic drive is replaced, an absolute reset must be performed, and the standard coordinate and point data must be reset. Refer to "Chapter 4 Adjustment" to adjust it.
5-49
2. Y-axis 1) Prepare the following tools and items. Harmonic grease 4B No.2 Waste cloth (rag) Phillips-head screwdriver Hex wrench set Screw Lock (thread sealant) Torque-limiting wrench Replacement parts (See table below.)
Replacement parts Parts name Harmonic drive O-ring Type No. SHF-25-80 S90(JIS) YAMAHA Parts No. KN4-M2110-001 KN4-M2143-000 Lower part of harmonic drive For motor Note
Cross section diameter: 1.30mm Inner diameter: 66.50mm KN5-M257L-000 Supplied with harmonic drive
2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the Y-axis arm upper cover. Place the cover on the robot base (pedestal) side with the machine harness still connected. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. 6) Disconnect the connectors on the Y-axis motor power cable YM and resolver cable YP. 7) Remove the Y-axis motor installation bolts (M620L, 4 pieces) and then remove the Y-axis motor by swaying it gently right and left. (See Fig. 5-41.)
M620 Spacer
Fig. 5-41
5-50
! CAUTION
An O-ring is fitted to the motor, so be careful not to let it drop into the peripheral unit.
8) Remove the wave generator from the motor shaft. The wave generator is secured with an M4 set screws. (See Fig. 5-45.) WARNING
When you remove the Y-axis arm installation bolts (M420L, 16 pieces) in the next step, the Y-axis arm may come off causing a hazardous situation. Be especially careful to keep the arm from falling when a heavy tool is attached to the arm tip.
9) Remove the Y-axis arm installation bolts (M420L, 16 pieces). (See Fig. 542.)
M420
Fig. 5-42 10) Remove the Y-axis arm and place it where it will not obstruct the work.
! CAUTION
An O-ring is fitted to the upper surface of the harmonic drive, so be careful not to let it drop into the peripheral unit.
5-51
11) Remove the Y-axis harmonic drive installation bolts (M445L, 8 pieces). (See Fig. 5-43.)
M445
Fig. 5-43 12) Remove the Y-axis harmonic drive from the top of the X-axis arm.
! CAUTION
An O-ring is fitted to the upper surface of the X-axis, so be careful not to let it drop into the peripheral unit. (See Fig. 5-44.)
Fig. 5-44 13) Fit a new O-ring coated with harmonic grease into the O-ring groove on the X-axis arm. (See Fig. 5-44.)
5-52
14) Place the new harmonic drive on the X-axis arm, and secure it with the bolts (M445L, 8 pieces) you removed earlier. Apply small amounts of "Screw Lock" to the bolts and tighten them uniformly to secure the harmonic drive from the backside. (See Fig. 5-43.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
15) Fit an O-ring (supplied with the harmonic drive) coated with harmonic grease into the O-ring groove on the new harmonic drive. (See Fig. 5-45.) 16) Secure the Y-axis arm to the harmonic drive with the bolts (M420L, 16 pieces) you removed earlier. Apply small amounts of "Screw Lock" to the bolts and tighten them uniformly to secure the Y-axis arm. (See Fig. 5-42.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
17) Apply harmonic grease to the new wave generator and flexspline. See Fig. 5-45 for applying grease properly. 18) Fit the wave generator onto the motor shaft, and fully insert it against the motor. Then, apply small amounts of "Screw Lock" to the M4 set screw (1 piece) you removed earlier and tighten it to secure the wave generator. (See Fig. 5-45.)
Fit O-ring (supplied) into this groove Harmonic drive will be damaged if O-ring is caught out of groove. O-ring : KN5-M257L-000 Apply grease to entire oldham coupling. O-ring : KN5-M2143-000 M4 set screw
Wave generator Apply grease to sufficiently fill in the ball space. Apply grease to the thickness equal to the ball diameter. Circular spline Never remove these temporarily tightened bolts. The axis will otherwise deviate from center.
Fig. 5-45
5-53
19) Fit a new O-ring to the motor and tighten the bolts (M620L, 4 pieces) you removed earlier to temporarily secure the motor to the Y-axis arm. (See Fig. 5-41.) Insert a new O-ring between the spacer and the Y-axis arm at this point.
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of groove.
20) Uniformly tighten the four bolts (M620L) temporarily fastened in the previous step while moving the Y-axis by hand slowly left and right through 45. If any jamming or catching is felt while moving the axis at this time, then reassemble from the beginning. 21) Reattach the connectors on the Y-axis motor power cable YM and resolver cable YP. 22) Reattach the Y-axis arm upper cover. 23) Go outside the safeguard enclosure. 24) Check that no one is inside the safeguard enclosure, and then turn on the controller.
! CAUTION
After the Harmonic drive is replaced, an absolute reset must be performed, and the standard coordinate and point data must be reset. Refer to "Chapter 4 Adjustment" to adjust it.
5-54
3. R-axis 1) Prepare the following tools and items. Harmonic grease 4B No.2 Waste cloth (rag) Phillips-head screwdriver Hex wrench set Screw Lock (thread sealant) Torque-limiting wrench Hook wrench Replacement parts (See table below.)
Replacement parts Parts name Harmonic drive O-ring Edge seal Type No. SHF-20-50 S71(JIS) VR28A YAMAHA Parts No. KN5-M1821-001 KN3-M2159-000 Lower part of harmonic drive KN5-M1886-000 Note
Cross section diameter: 0.99mm Inner diameter: 53.28mm KN3-M2144-000 Supplied with harmonic drive
2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the Y-axis arm upper cover. Place the cover on the robot base (pedestal) side with the machine harness still connected. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. WARNING
The Z-axis will slide down when the spline mounting bolts (M516L, 4 pieces) are removed in the next step, causing a hazardous situation. Prop the Z-axis with a support stand before loosening these bolts.
6) Remove the bolts (M516L, 4 pieces) securing the bearing to the upper end of the spline and remove the spline and bearing from the holder. (See Fig. 546.)
Holder
Bearing
M516
Spline shaft
Fig. 5-46
5-55
7) While placing a steel rod or similar tool through the 8mm diameter hole at the lower part of the spline, loosen the U-nut at the top of the spline with the hook wrench, and remove the bearing and bearing mount plate. (See Fig. 547.) Use a round steel rod with a diameter slightly smaller than 8mm. Avoid using a square rod because the spline might be damaged by the edge of the rod. At this time, be careful to keep the spline shaft from coming off the spline nut.
U-nut
Fig. 5-47 8) Remove the bolts (M310L, 12 pieces) on the lower side of the Y-axis arm, and remove the R-axis dog ring from the fastening plate. 9) Remove the bolts (M330L, 8 pieces) on the underside of the Y-axis arm and remove the plate fastening the spline and the harmonic drive. (See Fig. 5-48.)
M330
Fastening plate
Fig. 5-48
5-56
! CAUTION
An O-ring is fitted to the fastening plate, so be careful not to let it drop into the peripheral unit. (See Fig. 5-49.)
O-ring : KN3-M2159-000
Fig. 5-49 10) Remove the bolts (M415L, 4 pieces) securing the R-axis motor plate at the top of the Y-axis arm. (See Fig. 5-50.) 11) Loosen the pulley set screw (M4, 2 pieces) and remove the pulley from the wave generator. (See Fig. 5-50.) 12) Remove the harmonic drive installation bolts (M330L, 13 pieces) and pull out the harmonic drive from the bottom of the Y-axis arm. (See Fig. 5-50.)
M4 Set screw M330 M415
Pulley
Fig. 5-50
! CAUTION
An O-ring is fitted to the harmonic drive, so be careful not to let it drop into the peripheral unit.
13) Remove the retaining ring for the wave generator and pull out the wave generator from the bottom of the Y-axis arm.
5-57
14) Apply harmonic grease to the new wave generator. See Fig. 5-51 for applying grease properly.
Retaining ring groove Apply grease to sufficiently fill in the ball space. Fit O-ring (supplied) into this groove Harmonic drive will be damaged if O-ring is caught out of groove. O-ring : KN3-M2144-000 Wave generator Apply grease to entire oldham coupling. Apply grease to the thickness equal to the ball diameter. Circular spline
Never remove these temporarily tightened bolts. The axis will otherwise deviate from center.
Fig. 5-51 15) Insert the new wave generator into the Y-axis arm from the bottom, and secure it with the retaining ring. The chamfered side of the retaining ring should face downwards. 16) Apply harmonic grease to the circular spline. See Fig. 5-51 for applying grease properly. 17) Fit an O-ring (supplied with the harmonic drive) coated with harmonic grease into the O-ring groove on the new harmonic drive. (See Fig. 5-51.) Apply small amounts of "Screw Lock" to the bolts (M330L, 13 pieces) and tighten them to secure the harmonic drive to the Y-axis arm from the top of the Y-axis arm. (See Fig. 5-50.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
18) Apply small amounts of "Screw Lock" to the M4 set screws (2 pieces) and tighten them to secure the pulley to the wave generator. (See Fig. 5-50.) 19) Fit the timing belt onto the wave generator pulley and motor pulley, and then secure the motor plate. (See Fig. 5-50.)
! CAUTION
It is necessary to apply correct tension to the timing belt during reassembly. Refer to "8 Adjusting the Timing Belt Tension" in Chapter 4.
5-58
20) Fit a new O-ring into the O-ring groove on the fastening plate and also replace the edge seal with new one. Then secure the fastening plate to the harmonic drive with the bolts (M330L, 8 pieces) coated with small amounts of "Screw Lock". (See Fig. 5-48 and Fig. 5-52.) At this point, be careful to keep the spline shaft from coming off the spline nut.
! CAUTION
The harmonic drive service life may shorten if the edge seal effect is insufficient, so carefully reassemble the parts.
O-ring : KN3-M2159-000
Spline nut
Spline shaft
Fig. 5-52 21) Tighten the bolts (M310L, 12 pieces) to secure the dog ring to the fastening plate. 22) Insert the bearing mount plate and bearing onto the spline from the top, and tighten the U-nut to secure the bearing. (Utilize the 8 through-hole when tightening the U-nut like you did to loosen it.) (See Fig. 5-47.) 23) Insert the spline and bearing through the holder and secure them with the bolts you removed earlier (M516L, 4 pieces). (See Fig. 5-46.) 24) Reattach the Y-axis arm upper cover. 25) Go outside the safeguard enclosure. 26) Check that no one is inside the safeguard enclosure, and then turn on the controller.
! CAUTION
After the Harmonic drive is replaced, the absolute reset must be performed, and the point data must be reset. Refer to "Chapter 4 Adjustment" to adjust it.
5-59
5-2-4
YK1200X
The YK1200X uses a harmonic drive only for the R-axis. The following steps describe procedures and precautions when replacing this harmonic drive. For the bolt tightening torques in this work, refer to Table 5-2. 1) Prepare the following tools and items. Harmonic grease 4B No.2 Waste cloth (rag) Phillips-head screwdriver Hex wrench set Screw Lock (thread sealant) Torque-limiting wrench Hook wrench Replacement parts (See table below.)
Replacement parts Parts name Harmonic drive O-ring Edge seal Type No. SHF-25-50 S90(JIS) YAMAHA Parts No. KN6-M1821-001 KN4-M2143-000 Lower part of harmonic drive Note
Cross section diameter: 1.30mm Inner diameter: 66.50mm KN4-M257L-000 Supplied with harmonic drive Cross section diameter: 1.25mm Inner diameter: 37.50mm KN6-M1896-010 Wave generator support bearing section VR32A KN6-M1886-000
2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch.
4) Enter the safeguard enclosure. 5) Remove the Y-axis arm front cover. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. 6) Remove the bolts (M520L, 4 pieces) and then separate the spline support shaft (2 pieces) from the shaft fastening plate. (See Fig. 5-53.)
M430 Shaft fastening plate M520
Fig. 5-53
5-60
7) Remove the bolts (M620L, 4 pieces) securing the bearing to the upper end of the spline and remove the bearing mount plate. (See Fig. 5-54.)
M620
Bearing
Holder
8) While holding a steel rod or similar tool through the 10mm diameter hole as shown, use the hook spanner to remove the U-nut on the spline shaft and then remove the bearing. (See Fig. 5-55.) Use a round steel rod with a diameter slightly smaller than 10mm. Avoid using a square rod because the spline might be damaged by the edge of the rod. Be careful at this point to keep the spline shaft from coming off the spline.
U-Nut
Spline shaft
Fig. 5-55
5-61
9) Remove the bolts (M414L, 2 pieces) on the underside of the Y-axis arm and remove the R-axis dog ring from the fastening plate. 10) Remove the bolts (M430L, 8 pieces) on the underside of the Y-axis arm and remove the plate fastening the spline and the harmonic drive. (See Fig. 5-53.)
! CAUTION
An O-ring is fitted to the fastening plate, so be careful not to let it drop into the peripheral unit. (See Fig. 5-56.)
O-ring : KN4-M2143-000
Fig. 5-56 11) Remove the bolts (M620L, 4 pieces) securing the R-axis motor plate at the top of the Y-axis arm. (See Fig. 5-57.) 12) Loosen the pulley bolts (M330L, 4 pieces) and remove the pulley fastened to the wave generator. (See Fig. 5-57.) 13) Remove the harmonic drive installation bolts (M445L, 12 pieces) and pull out the harmonic drive from the bottom of the Y-axis arm. (See Fig. 5-57.)
M445 M330 M620
pulley
Fig. 5-57
! CAUTION
An O-ring is fitted to the harmonic drive, so be careful not to let it drop into the peripheral unit.
14) Pull out the wave generator from the bottom of the Y-axis arm.
5-62
! CAUTION
An O-ring is fitted to the wave generator, so be careful not to drop it into the peripheral unit.
15) Apply harmonic grease to the new wave generator. See Fig. 5-58 for applying grease properly.
Wave generator Apply grease to entire oldham coupling. Fit O-ring (supplied) into this groove Harmonic drive will be damaged if O-ring is caught out of groove. O-ring : KN5-M257L-000 O-ring groove O-ring : KN6-M1896-010 Apply grease to sufficiently fill in the ball space. Apply grease to the thickness equal to the ball diameter. Circular spline
Never remove these temporarily tightened bolts. The axis will otherwise deviate from center.
Fig. 5-58 16) Fit the O-ring coated with harmonic grease into the O-ring groove on the new wave generator (wave generator support bearing section), and then insert the wave generator into position from the bottom of the Y-axis arm.
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
17) Apply harmonic grease to the circular spline. See Fig. 5-58 for applying grease properly. 18) Fit an O-ring (supplied with the harmonic drive) coated with harmonic grease into the O-ring groove on the new harmonic drive. (See Fig. 5-58.) Apply small amounts of "Screw Lock" to the bolts (M445L, 12 pieces) and tighten them to secure the harmonic drive to the Y-axis arm from the top of the Y-axis arm. (See Fig. 5-57.)
! CAUTION
Do not allow the O-ring to get caught out of the groove during reassembly. A problem will occur if the robot is operated with the O-ring left caught out of the groove.
19) Apply small amounts of "Screw Lock" to the bolts (M330L, 4 pieces) and tighten them to secure the pulley to the wave generator. (See Fig. 5-57.) 20) Fit the timing belt onto the wave generator pulley and motor pulley, and then secure the motor plate. (See Fig. 5-57.)
5-63
! CAUTION
When securing the timing belt, the belt tension must be adjusted properly. See "8. Adjusting the Timing Belt Tension" in Chapter 4 for how to adjust the belt tension.
21) Fit a new O-ring into the O-ring groove on the fastening plate and also replace the edge seal with new one. Then, secure the fastening plate to the harmonic drive with the bolts (M430L, 8 pieces) coated with small amounts of "Screw Lock". (See Figs. 5-53 and 5-59.) At this point, be careful to keep the spline shaft from coming off the spline nut.
! CAUTION
The harmonic drive service life may shorten if the edge seal effect is insufficient, so carefully reassemble the parts.
Edge seal Fastening plate
O-ring : KN4-M2143-000
Spline nut
Spline shaft
Fig. 5-59 22) Secure the dog ring to the fastening plate with the bolts (M414L, 2 pieces). 23) Insert the spline shaft into the holder, fit the bearing onto the spline and tighten the U-nut to secure the bearing. (Utilize the 10 through-hole when tightening the U-nut like you did to loosen it.) (See Fig. 5-55.) 24) Put the bearing into the holder and tighten the bolts (M620L, 4 pieces) to secure the bearing mount plate to the holder (See Fig. 5-54.) 25) Install the spline support shafts (2 pieces) to the fastening plate, apply a small amount of "Screw Lock" to the bolts (M520L, 4 pieces) and tighten. (See Fig. 5-53.) 26) Attach the Y-axis arm front cover. 27) Go outside the safeguard enclosure. 28) Check that no one is inside the safeguard enclosure, and then turn on the controller.
5-64
5-2-5
5-65
6-1
Replacement period
The harmonic grease replacement period is determined by the total number of turns of the wave generator used in the harmonic drive. It is recommended to replace the harmonic grease when the total number of turns has reached 1.5108 (at ambient operating temperatures of 0C to +40C). This means that the replacement period will differ depending on the following operating conditions. If the robot operation duty ratio is high or the robot is operated in environments at higher temperatures, the grease should be replaced earlier. (Operating conditions) n : Number of axis movements per minute q : Average turn per axis movement N : Speed ratio h : Operation time per day D : Operation days per year For example, when the robot is used under the following conditions, the replacement period can be calculated as follows. n : 10 q : 1/4 turn N : 50 h : 24 hours per day D : 240 days per year Replacement period = 1.5108/(n60hDN) = 1.5108/(106024240501/4) = 3.47 years
Axis X, Y, R Speed Ratio 50
5-66
6-2
WARNING
Precautions when handling harmonic grease, cleaning oil: Inflammation may occur if they get in the eyes. Before handling them, wear your safety goggles to ensure they will not come in contact with the eyes. Inflammation may occur if they come into contact with skin. Be sure to wear protective gloves to prevent contact with skin. Do not take orally or eat. (Eating will cause diarrhea and vomiting.) Hands and fingers might be cut when opening the container, so use protective gloves. Keep out of the reach of children. Do not heat them or place near an open flame since this could lead to sparks and fires. Emergency Treatment: If they get in the eyes, wash liberally with pure water for about 15 minutes and consult a physician for treatment. If they come in contact with the skin, wash away completely with soap and water. If taken internally, do not induce vomiting but promptly consult a physician for treatment.
WARNING
Disposing of harmonic grease, cleaning oil and the container: Proper disposal is compulsory under federal, state and local regulations. Take appropriate measures in compliance with legal regulations. Do not pressurize the empty container. Pressurizing may cause the container to rupture. Do not attempt to weld, heat up, drill holes or cut this container. This might cause the container to explode and the remaining materials inside it to ignite.
5-67
WARNING
When removing the wave generator from the motor shaft or reinstalling it back onto the motor shaft, use caution to avoid as much as possible, applying a thrust load to the motor shaft. If a load is applied, the resolver may be damaged resulting in a hazardous situation of the robot malfunction.
! CAUTION
The harmonic drive service life may decline drastically if the grease recommended by YAMAHA is not used.
! CAUTION
Harmonic drive Do not apply strong shocks or impacts to these parts such as with a hammer. Also, do not scratch, scar or dent these parts by dropping, etc. Such actions will damage the harmonic drive. The specified performance cannot be maintained if any part of the harmonic drive is used in a damaged state. This damage or wear may also lead to trouble with the harmonic drive.
! CAUTION
Deviations in position may occur due to replacement of the harmonic grease. This means that the machine reference adjustment, standard coordinate setting and point data settings are required after replacing the grease.
1) Prepare the following tools and items necessary for replacing the grease. Harmonic grease HC-IA Waste cloth Phillips screwdriver Cleaning oil (kerosene, etc.) Magic marker Air gun Hex wrench set Screw lock Ratchet handle (insertion angle 6.35mm, 9.5mm) Hexagonal socket set (insertion angle 6.35mm, 9.5mm) Torque wrench (insertion angle 6.35mm, 9.5mm) Extension bar (insertion angle 9.5mm, length 75mm) 2) Turn off the the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch.
5-68
4) Enter the safeguard enclosure. 5) To make reassembly easier, put marks on the motor holder, circular spline, Yaxis arm and X-axis arm to indicate their relational positions before proceeding to the next step, as shown in Fig. 5-60. The circular spline can be seen after removing the motor holder. 6) Remove the four M4 bolts securing the motor holder. 7) Slowly pull out the motor along with the motor holder, while swaying the motor slightly left and right. At this time, make every effort to avoid rotating the motor shaft. 8) Remove the M6 set screw from the motor holder. (See Fig. 5-62.) 9) Align the key with the M6 hole, and insert the 2mm hex wrench into the M6 hole to loosen the internal M4 set screw. Then, remove the wave generator from the motor shaft.
Motor holder Y-axis motor
Flexspline
Washer Mark
Y-axis arm
X-axis arm
Mark
Fig. 5-60 Harmonic drive grease replacement section and position markings 10) Remove the eight M4 bolts securing the circular spline and slowly pull out the circular spline to remove it. Use the puller taps if difficult to remove the circular spline. 11) Finally, remove the eight M6 bolts securing the flexspline and washer on the inner side of the circular spline, and remove the flexspline and washer. If the bolts are hard to see due to grease, remove the grease to make the job easier. Use the puller taps on the bottom if difficult to remove these parts.
5-69
12) Remove the old grease from the washer, flexspline, circular spline and wave generator with a waste cloth, and then clean further with cleaning oil and by blow from an air gun. The harmonic drive components are precision parts so be careful not to drop them.
Apply grease to entire oldham coupling. Apply grease to the thickness of the ball. Fill all the gear grooves completely. Fill the ball space sufficiently.
Lightly coat the outer circumference. (Circular spline) (Flexspline) (Wave generator)
Fig. 5-61 Applying grease 13) Apply the harmonic grease to the wave generator, circular spline, and flexspline. See Fig. 5-61 for the basics on applying the grease. Do not apply grease to the washer. 14) Install the circular spline onto the Y-axis arm. Tighten the eight M4 bolts while aligning with the marks you previously made. Take care not to let foreign matter such as dirt or grit become mixed with the grease or parts during installation. See below for the tightening torque of each bolt.
Tightening torque M3 bolt 2.0Nm (20kgfcm) M4 bolt 4.5Nm (46kgfcm) M5 bolt 9.0Nm (92kgfcm) M6 bolt 15.3Nm (156kgfcm) M8 bolt 37Nm (380kgfcm)
15) While aligning the Y-axis arm and X-axis arm with their marks, gently insert the flexspline into the circular spline. Then put the washers in place and tighten the eight M6 bolts on the inner side of the circular spline, in order from the diagonally opposite positions. 16) Insert the wave generator onto the motor shaft so it makes tight contact with the motor holder as shown in Fig. 5-62, then apply small amounts of "Screw Lock" (thread sealant) to the M4 set screw and tighten to secure the wave generator. At this time, make every effort to avoid rotating the motor shaft. 17) While aligning the Y-axis arm mark with the motor holder mark, gently insert the wave generator into the circular spline by moving it slightly left and right.
5-70
18) Tighten the four M4 bolts on the motor holder gradually while gently moving the Y-axis arm by hand 45 degrees left and right. If you feel any hang-ups or abnormalities, take apart and reassemble again. 19) Go outside the safeguard enclosure. 20) Check that no one is inside the safeguard enclosure and then turn on the controller. 21) Perform absolute reset and adjust the Y-axis machine reference. Also set the reference coordinates and point data.
8.2mm (when fully inserted)
M4 set screw
M6 hole
Motor
Wave generator
5-71
6-3
WARNING
Bodily injury may occur from coming into contact with the X-axis cooling fan while it is rotating. When removing the cover on the base (pedestal), first turn off the controller and make sure the fan has stopped.
1) Prepare the following tools and items. Harmonic grease HC-IA Waste cloth Phillips screwdriver Cleaning oil (kerosene, etc.) Torque wrench (insertion angle 6.35mm, 9.5mm) Magic marker Air gun Hex wrench set Screw lock Ratchet handle (insertion angle 6.35mm, 9.5mm) Hexagonal socket set (insertion angle 6.35mm, 9.5mm) Extension bar (insertion angle 6.35mm, length 150mm) Extension bar (insertion angle 9.5mm, length 75mm) Socket adapter (9.5mm , 6.35mm ) 2) Turn off the controller. 3) Place a sign indicating the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the front and rear covers shown in the figure of the base, and also remove the rear cover shown in Fig. 5-63 (a). 6) Unplug the connectors of the X-axis motor power wire XM and the resolver wire XP. 7) Mark the relative positions beforehand of the motor holder, circular spline, base (pedestal) and X-axis arm with a magic marker, in order to make the reassembly job easier. The circular spline can be seen when the motor holder is removed. (See Fig. 5-63 (b), (d).)
5-72
8) Remove the four M5 bolts for the motor holder, using the ratchet handle, hexagonal socket, extension bar, socket adapter and hex wrench. (See Fig. 563 (c).) 9) WARNING
Carefully remove the motor so as not to let hands or fingers get pinched between the motor and the base.
Remove the motor along with the motor holder, by pulling it gently right and left. Make every effort to avoid rotating the motor shaft at this time. 10) Remove the M6 set screw from the motor holder. (See Fig. 5-64.) 11) Align the key with the M6 hole, and insert the 2mm hex wrench into the M6 hole to loosen the internal M4 set screw. Then, remove the wave generator from the motor shaft. 12) From this step, use the same procedure explained from step 10) in Section 62. In reassembly, insert the wave generator all the way onto the motor shaft, so that it is in the position as shown in Fig. 5-64. Then, apply small amounts of "Screw Lock" to the M4 set screw and tighten to secure the wave generator.
5-73
Motor holder
X-axis motor
(d)
Fig. 5-63 Harmonic drive grease replacement section and position markings
7.1mm (when fully inserted)
M4 set screw
M6 hole
Motor
Wave generator
Key
Motor holder
6-4
Mark
Spline
Fig. 5-65 Harmonic drive grease replacement section and position markings
5-75
M4 set screw
M6 hole
Motor
Wave generator
Motor holder
5-76
7-1
Replacement period
The grease replacement period is typically 20,000 hours of operation. However, if the robot operation duty ratio is higher or the robot is operated in environments at higher or lower temperatures, the grease should be replaced earlier.
7-2
Recommended grease
Use the following grease. Daphne Eponex grease EP-0 (Idemitsu Kosan) or equivalent Replenishment grease amount (for new RV speed reduction gears) X-axis speed reduction gear 514 cc Y-axis speed reduction gear 192 cc
! CAUTION
The RV speed reduction gear service life may shorten if the grease recommended by YAMAHA is not used.
5-77
7-3
Replacement procedure
WARNING
The motor and speed reduction gear casing are extremely hot after automatic operation, so burns may occur if these are touched. Before touching these parts, turn off the controller, wait for a while and check that the temperature has cooled.
WARNING
Precautions when handling grease: Inflammation may occur if this gets in the eyes. Before handling the grease, wear your safety goggles to ensure the grease will not come in contact with the eyes. Inflammation may occur if the grease comes into contact with skin. Be sure to wear protective gloves to prevent contact with skin. Do not take orally or eat. (Eating will cause diarrhea and vomiting.) Hands and fingers might be cut when opening the container, so use protective gloves. Keep out of the reach of children. Do not heat the grease or place near an open flame since this could lead to sparks and fires. Emergency Treatment: If this grease gets in the eyes, wash liberally with pure water for about 15 minutes and consult a physician for treatment. If this grease comes in contact with the skin, wash away completely with soap and water. If taken internally, do not induce vomiting but promptly consult a physician for treatment.
! CAUTION
Disposing of grease and the container: Proper disposal is compulsory under federal, state and local regulations. Take appropriate measures in compliance with legal regulations. Do not pressurize the empty container. Pressurizing may cause the container to rupture. Do not attempt to weld, heat up, drill holes or cut this container. This might cause the container to explode and the remaining materials inside it to ignite.
5-78
7-3-1
Replacing the X-axis grease (first product to products manufactured in September 2009)
1) Prepare the following tools and items. Daphne Eponex grease EP-0 Hex wrench set Air tube coupler (PT1/8) Air tube Rag Grease gun 2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the base (robot pedestal) front cover and the X-axis arm top cover. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. 6) Remove the plug on the top of the X-axis arm. (See Fig. 5-67.) 7) To remove the old grease from the X-axis, attach the air coupler (PT1/8) into the screw hole where the plug was fitted and connect the air tube to the air coupler. The old grease inside the X-axis will be squeezed out by replenishing new grease with a grease gun as explained in the next steps. 8) Using the grease gun, pump the specified grease into the grease nipple located on the front of the robot base. (See Fig. 5-68.) 9) After replenishing the grease, move the X-axis arm by hand back and forth a few times (about 90 degrees) and then remove excess grease. 10) Remove the air coupler and then reattach the plug, X-axis top cover and base front cover. 11) Go outside the safeguard enclosure. 12) Check that no one is inside the safeguard enclosure, and then turn on the controller.
Plug Air tube coupler
Grease nipple
Fig. 5-67
Fig. 5-68
5-79
7-3-2
Replacing the X-axis grease (products manufactured from October 2009 onward)
1) Prepare the following tools and items. Daphne Eponex grease EP-0 Hex wrench set Air tube coupler (PT1/8) Air tube Grease nipple (A-MT81) Grease gun Rag Sealing tape (NITOFLON PIPESEAL, etc.) 2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the base (robot pedestal) front cover and the X-axis arm top cover. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. 6) Remove the plug on the top of the X-axis arm. (See Fig. 5-69.) 7) To remove the old grease from the X-axis, attach the air coupler (PT1/8) into the screw hole where the plug was fitted and connect the air tube to the air coupler. The old grease inside the X-axis will be squeezed out by replenishing new grease with a grease gun as explained in the next steps. 8) Remove the plug on the front (section A) of the robot base and attach the grease nipple (A-MT81) there. (See Fig. 5-70.) Keep the removed plug, as it will be used after replenishing grease. 9) Using the grease gun, supply the specified grease into the grease nipple until the old grease is squeezed out from the upper tube. 10) When the old grease no longer comes out of the tube, remove the grease nipple attached to the front (section A) of the robot base, and fit the plug into place. When fitting the plug, wrap sealing tape around it to prevent grease from leaking out. 11) After replenishing the grease, move the X-axis arm by hand back and forth a few times (about 90 degrees) and then remove excess grease. 12) Remove the air coupler, then fit the plug into place on the top of the X-axis arm and reattach the base front cover. When fitting the plug, wrap sealing tape around it to prevent grease from leaking out. 13) Go outside the safeguard enclosure. 14) Check that no one is inside the safeguard enclosure, and then turn on the controller.
Plug Air tube coupler
Plug (section A)
Base
Fig. 5-69
5-80
Fig. 5-70
7-3-3
Replacing the Y-axis grease (first product to products manufactured in September 2009)
1) Prepare the following tools and items. Daphne Eponex grease EP-0 Hex wrench set Air tube coupler (PT1/8) Air tube Rag Grease gun 2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the X-axis arm under cover. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. 6) Remove the plug on the top of the Y-axis arm. (See Fig. 5-71.) 7) To remove the old grease from the Y-axis, attach the air coupler (PT1/8) into the screw hole where the plug was fitted and connect the air tube to the air coupler. The old grease inside the Y-axis will be squeezed out by replenishing new grease with a grease gun as explained in the next steps. 8) Using the grease gun, pump the specified grease into the grease nipple located on the bottom of the X-axis arm. (See Fig. 5-72.) 9) After replenishing the grease, move the Y-axis arm by hand back and forth a few times (about 90 degrees) and then remove excess grease. 10) Remove the air coupler and then reattach the plug and X-axis arm under cover. 11) Go outside the safeguard enclosure. 12) Check that no one is inside the safeguard enclosure, and then turn on the controller.
Air tube coupler
Grease nipple
Plug Y-axis arm
Fig. 5-71
Fig. 5-72
5-81
7-3-4
Replacing the Y-axis grease (products manufactured from October 2009 onward)
1) Prepare the following tools and items. Daphne Eponex grease EP-0 Hex wrench set Air tube coupler (PT1/8) Air tube Grease nipple (A-MT81) Grease gun Rag Sealing tape (NITOFLON PIPESEAL, etc.) 2) Turn off the controller. 3) Place a sign indicating that the robot is being inspected, to keep others from operating the controller switch. 4) Enter the safeguard enclosure. 5) Remove the X-axis arm under cover. Refer to "7 Removing the Robot Covers" in Chapter 4 for removing the covers. 6) Remove the plug on the top of the Y-axis arm. (See Fig. 5-73.) 7) To remove the old grease from the Y-axis, attach the air coupler (PT1/8) into the screw hole where the plug was fitted and connect the air tube to the air coupler. The old grease inside the Y-axis will be squeezed out by replenishing new grease with a grease gun as explained in the next steps. 8) Remove the plug on the underside (section A) of the X-axis arm and attach the grease nipple (A-MT81) there. (See Fig. 5-74.) Keep the removed plug, as it will be used after replenishing grease. 9) Using the grease gun, supply the specified grease into the grease nipple until the old grease is squeezed out from the upper tube. 10) When the old grease no longer comes out of the tube, remove the grease nipple attached to the underside (section A) of the X-axis arm, and fit the plug into place. When fitting the plug, wrap sealing tape around it to prevent grease from leaking out. 11) After replenishing the grease, move the Y-axis arm by hand back and forth a few times (about 90 degrees) and then remove excess grease. 12) Remove the air coupler, then fit the plug into place on the top of the Y-axis arm and reattach the X-axis arm under cover. When fitting the plug, wrap sealing tape around it to prevent grease from leaking out. 13) Go outside the safeguard enclosure. 14) Check that no one is inside the safeguard enclosure, and then turn on the controller.
Air tube coupler Plug Y-axis arm Plug (section A)
Fig. 5-73
5-82
Fig. 5-74
CHAPTER 6
MEMO
Z=0
P2
P3
P1
P4
w Arch motion: Using default arch position: (2000 pulses) From point P1 to P2: MOVE P, P2, Z=0 M1, M2, M4 "Axis parameters" "Arch position" M1 (X-axis arch position) = 2000 pulses M2 (Y-axis arch position) = 2000 pulses M3 (Z-axis arch position) = 2000 pulses M4 (R-axis arch position) = 2000 pulses
Z=0 M3 P1 P2
When the Z-axis moves upward from P1 and enters the M3 arch position range (2000 pulses prior to Z=0), the X, Y and R axes begin to move. When these 3 axes enter the M1, M2 and M4 arch position range (2000 pulses prior to P2), the Zaxis moves downward to P2. Compared with the gate motion q, this arch motion shortens the cycle time approximately 20% by moving the robot arm along an arc.
6-1
e Arch motion: Making the arch position value larger In the arch motion w, making the arch position value larger can further shorten the cycle time. Since the robot arm moves along a larger arc, use caution to avoid obstacles if they are located near the arm movement path. The arch position parameter can be set for each axis. r Arch motion: changing the arch positions in the program From point P1 to P2 and then to P3: ARCH (1) = 10000 ... X-axis arch position (pulses) Arch position can be set for each axis. ARCH (2) = 20000 ... Y-axis arch position (pulses) ARCH (3) = 20000 ... Z-axis arch position (pulses) ARCH (4) = 20000 ... R-axis arch position (pulses) MOVE P, P2, Z=0 If the same arch position value ARCH (1) = 2000 (pulses) is used for all axes, you ARCH (2) = 2000 can write as "ARCH 2000". ARCH (3) = 2000 ARCH (4) = 2000 MOVE P, P3, Z=100 Since the arch positions can be changed in the program, optimizing the arch positions can further shorten the cycle time.
Arch position: large Z=0 Arch position: small Z=100
P1
P2
P3
6-2
(2) Increasing the speed with the WEIGHT statement [Also refer to:] Robot controller user's manual ("Robot parameters" "Axis tip weight" in Chapter 4) Programming manual (WEIGHT statement in "11. Command statements".) [Example] From P1 when chuck is open: WEIGHT 5 ........ Changes the axis tip weight parameter to 5kg (no workpiece). MOVE P, P2, Z=0 DO3 (0) = 1 ....... Chuck closes. WEIGHT 10 ...... Changes the axis tip weight parameter to 10kg (with workpiece). MOVE P, P3, Z=0 In the above program, the acceleration can be set to a higher level by reducing the axis tip weight parameter to 5kg while the chuck does not grip any workpiece, and then set to a lower level by changing the axis tip weight parameter to 10kg. Compared to programs using an axis tip weight parameter left set at 10kg, this method shortens the cycle time since the acceleration is increased.
No workpiece Z=0 Chuck is gripping workpiece.
P1 Chuck opens.
P2 Chuck closes.
P3
6-3
(3) Increasing the speed by the tolerance parameter [Also refer to:] Robot controller user's manual ("Axis parameters" "Tolerance" in Chapter 4) Programming manual (TOLE statement in "11. Command statements".)
P2
P3 [Example] P1 From P1 to P3 via P2 TOLE (1) = 2048 ... X-axis tolerance (pulses) : Increases the tolerance. TOLE (2) = 2048 ... Y-axis tolerance (pulses) Tolerance can be set for each axis. If the same tolerance is used for all TOLE (3) = 2048 ... Z-axis tolerance (pulses) axes, you can write as "TOLE TOLE (4) = 2048 ... R-axis tolerance (pulses) 2048". MOVE P, P2 TOLE (1) = 80 ....... Returns the tolerance to the default value. If the same tolerance is used for all axes, you can write as "TOLE 80". TOLE (2) = 80 TOLE (3) = 80 TOLE (4) = 80 MOVE, P, P3
When P2 is an escape point and does not need to be accurately positioned, setting the tolerance parameter to a larger value allows the robot arm to pass through P2 quickly. The larger the tolerance value for the positioning time, the shorter the cycle time will be. The maximum value of the tolerance parameter is 2048 (pulses) and the default is 80 (pulses).
6-4
(4) Increasing the speed by the OUT effective position parameter [Also refer to:] Robot controller user's manual ("Axis parameters" "Out effective Position" in Chapter 4) Programming manual (OUTPOS statement in "11. Command statements".) [Example] From P1 when chuck is open: OUTPOS (1) = 10000 ... X-axis OUT effective position (pulses) : Increases the OUT effective position. OUTPOS (2) = 10000 ... Y-axis OUT effective position (pulses) The OUT effective position can be set for each axis. OUTPOS (3) = 10000 ... Z-axis OUT effective position (pulses) If the same OUT effective OUTPOS (4) = 10000 ... R-axis OUT effective position (pulses) position is used for all axes, you MOVE P, P2, Z=0 can write as "OUTPOS 10000". DO3 (0) = 1 .................. Chuck closes. OUTPOS (1) = 2000 ..... Returns the OUT effective position to the default value. If the same OUT effective position is used for all OUTPOS (2) = 2000 axes, you can write as OUTPOS (3) = 2000 "OUTPOS 2000". OUTPOS (4) = 2000
P1
P2 Chuck closed.
When all of the X, Y, Z and R axes enter the OUT effective position (10000 pulses prior to P2), the chuck starts closing. By setting the OUT effective position larger, the chuck starts closing while the robot arm is still moving at an earlier point, so that the chuck can grip the workpiece more quickly. The default value of the OUT effective position is 2000 (pulses). [Reference] Relation between X, Y, R-axis rotating angle, Z-axis movement distance and pulse values The arch position, tolerance and OUT effective position parameters are set in pulses. For the relation between X, Y, R-axis rotating angle, Z-axis movement distance and pulse values, refer to the tables listed under item (4) in "4. Setting the soft limits". (Chapter 4 in this manual)
6-5
MEMO
6-6
CHAPTER 7
Specifications
1 Manipulator .............................................................................7-1
1-1 1-2 1-3 1-4 Basic specification ........................................................................... 7-1 External view and dimensions ......................................................... 7-4 Robot inner wiring diagram ............................................................ 7-30 Wiring table .................................................................................... 7-33
MEMO
CHAPTER 7 Specifications
Manipulator
1-1
Basic specification
Robot model X-axis Axis specifications Y-axis Z-axis Arm length Rotation angle Arm length Rotation angle Stroke X-axis Motor Y-axis Z-axis R-axis XY resultant Maximum speed Z-axis R-axis XY-axes Repeatability *1 Payload R-axis tolerable moment of inertia *2 User wiring User tubing Travel limit Robot cable Weight 15kg Z-axis R-axis YK250X(H) 125mm 115 125mm 140 150mm 180 200W 100W 100W 100W 4.0m/s 1.0m/s 1020/s 0.01mm 0.01mm 0.005 YK350X(H) 225mm 115 125mm 140 150mm 180 200W 100W 100W 100W 5.0m/s 1.0m/s 1020/s 0.01mm 0.01mm 0.005 3kg 0.05kgm2 (0.5kgfcms2) 10cables 43 1.Soft limit 2.Mechanical limit (XYZ-axes) 3.5m (option: 5m, 10m) 15kg 15kg YK400X(H) 225mm 115 175mm 140 150mm 180 200W 100W 100W 100W 6.0m/s 1.0m/s 1020/s 0.01mm 0.01mm 0.005
*1 At constant ambient temperature (XY) *2 There are limits to acceleration coefficient settings.
7-1
CHAPTER 7 Specifications
Robot model X-axis Axis specifications Y-axis Z-axis Arm length Rotation angle Arm length Rotation angle Stroke X-axis Motor Y-axis Z-axis R-axis XY resultant Maximum speed Z-axis R-axis XY-axes Repeatability *1 Payload R-axis tolerable moment of inertia *2 User wiring User tubing Travel limit Robot cable Weight Z-axis R-axis
YK500X 250mm 120 250mm 145 200,300mm 180 400W 200W 200W 100W 4.9m/s 1.7m/s 876/s 0.02mm 0.01mm 0.005 10kg
YK600X 350mm 120 250mm 145 200,300mm 180 400W 200W 200W 100W 5.6m/s 1.7m/s 876/s 0.02mm 0.01mm 0.005
YK550X
YK550X with high-speed R-axis specifications 300mm 90 250mm 145 200mm 180 800W 200W 200W 100W 6.7m/s 2.3m/s
540/s
1.Soft limit 2.Mechanical limit (XYZ-axes) 3.5m (option: 5m, 10m) 28kg 28kg 46kg
*1 At constant ambient temperature (XY) *2 There are limits to acceleration coefficient settings.
7-2
CHAPTER 7 Specifications
Robot Model X-axis Axis specifications Y-axis Z-axis Arm length Rotation angle Arm length Rotation angle Stroke X-axis Motor Y-axis Z-axis R-axis XY resultant Maximum speed Repeatability *1 Z-axis R-axis X,Y-axes Z-axis R-axis Payload R-axis tolerable moment of inertia *2 User wiring User tubing Travel limit Robot cable Weight
YK700X 350mm 120 350mm 145 200,400mm 180 800W 400W 400W 200W 6.7m/s 1.7m/s 600/s 0.02mm 0.01mm 0.005
YK800X 450mm 120 350mm 145 200,400mm 180 800W 400W 400W 200W 7.3m/s 1.7m/s 600/s 0.02mm 0.01mm 0.005 20kg
YK1000X 550mm 120 450mm 145 200,400mm 180 800W 400W 400W 200W 8.0m/s 1.7m/s 600/s 0.02mm 0.01mm 0.005
2
YK1200X 6000mm 125 600mm 150 400mm 180 900W 800W 600W 400W 7.4m/s 0.75m/s 600/s 0.05mm 0.02mm 0.005 50kg 2.45kgm2(25kgfcms2)
0.32kgm (3.2kgfcms )
2
20 cables 63 1.Soft limit 2.Mechanical limit (XYZ-axes) 3.5m,option:5m,10m 56kg 57kg 58kg 124kg
At constant ambient temperature (XY) *1 *2 There are limits to acceleration coefficient settings.
Sound level
Robot model Maximum sound pressure level of robot (at 10dB or more difference from background sound pressure level )
69.8dB 69.7dB 69.4dB 75.1dB
Note: Sound level may increase when sound reflecting objects are located near the robot.
7-3
CHAPTER 7 Specifications
1-2
112.2
125 45 120
165
55
52
125 78.7 70
R5 0
74
576
251
203.5
1522
150
7-4
140
CHAPTER 7 Specifications
140
14 0
5 11
11 5
0 R25
R86
R1
25
90
90
120
Working envelope (1 : 5)
145
13
145
13
0 R 25
R7
R1
25
120
63
M4 ground terminal
7-5
CHAPTER 7 Specifications
112.2
125 45 120
165
55 52
125 78.7 70
R5 0
100
3-R3
120
644 454 250 86 45 0
74
135 User tubing 1 (4 black) User tubing 2 (4 red) User tubing 3 (4 blue) 165
15
576
54 31
79 3
203.5
41
36
150
M8x1.25 Depth 15
7-6
140
CHAPTER 7 Specifications
140
14 0
5 11
11 5
0 R25
R86
R1
25
85
140
85
Working envelope (1 : 5)
13
142
142
13
R8
R1
25
R25 0
59
140
59
M4 ground terminal
7-7
CHAPTER 7 Specifications
112.2
R5 0
225 45 120
165
100
120
3-R5
74
135 User tubing 1 (4 black) User tubing 2 (4 red) User tubing 3 (4 blue) 165
15
644
576
454
251 5
250
203.5
41 36
1522
150
86 45
7-8
140
125 78.7 70
55 52
CHAPTER 7 Specifications
5 11
11 5
R1
52
R3
50
R1
25
140
140
Working envelope (1 : 5)
132
132
R1
42
50 R3
5 R12
145
145
M4 ground terminal
7-9
CHAPTER 7 Specifications
112.2
225 45 120
165
52 55
125 78.7 70
R5 0
100
3-R3 135 165 15 79 3
0 16h7 -0.018
74
644
576
454
250 54 31
203.5
144.52
41 36
150
M8x1.25 Depth 15
86 45
7-10
120 140
CHAPTER 7 Specifications
14
14 0
5 11
11 5
R15
R3
50
R1
25
140
140
Working envelope (1 : 5)
2 14
14
132
132
R1
48
R3
50
R12
99
140
99
M4 ground terminal
7-11
CHAPTER 7 Specifications
166.1
R5 0
225 45 120
165
60 55
175
3-R5 74
135 165
15
576
251 5 41 36 1522
150
7-12
CHAPTER 7 Specifications
5 11
11 5
R4
00
R145
R1 75
140
140
Working envelope (1 : 5)
156
156
132
132
R4
00
R92
R1
75
120
86
M4 ground terminal
7-13
CHAPTER 7 Specifications
166.1
225 45 120
165
175
60 55
85.3 72
R5 0
100
3-R3 135 User tubing 1 (4 black) User tubing 2 (4 red) User tubing 3 (4 blue) 165 15 79 3
120
644 454 250 86 45 0
74
576
54 31
203.5
41
36
150
M8x1.25 Depth 15
7-14
140
CHAPTER 7 Specifications
14
14
5 11
11 5
R4
00
R145
R1 75
115
140
115
Working envelope (1 : 5)
15 4
15
132
132
R400
R10 2
R1
75
82
82
140
M4 ground terminal
7-15
CHAPTER 7 Specifications
41
240
R57
201 159
R1 1 0
82
70
Fan outlet
140
D-sub connector for user wiring (No. 1 to 20 usable) (When Y-axis maximum working envelope is set to 940mm.) 909
812
M4 ground terminal 492 446 Z-axis upper end mechanical stopper 381 position 3262
15
15
15
70 140
250
670
359 Use caution to avoid interference of load with robot cable, user wiring or tubing User tubing 2 (6 blue) User tubing 1 (6 black) Fan position 172
200
44 16 0
7-16
CHAPTER 7 Specifications
90
90
2(
a)
R5
50
Interference position (a) Base flange (b) Base rear side (c) Base
R172
R6
145
R6 0( b)
(c) R86
93
93
(c
R2
59
R5
6(
R1
a)
R5
50
R41 (b
148
148
) Radius in which load interferes with robot when X or Y-axis strikes mechanical stopper
X and Y-axis mechanical stopper positions (maximum working envelope) *The area between working envelope and X or Y-axis mechanical stopper position cannot be used. 18.2
0 -0.25
16h7
30
10
0 -0.018
M121.75 Depth 20
7-17
14
CHAPTER 7 Specifications
54.5
250
122.5
R80
R2 0
90
96
70
D-sub connector for user wiring (No. 1 to 20 usable) User tubing 3 (6 blue)
65
160
94
R200
110 65
R55
790
667
561
36
363 54 20 7 48 41
2372
300
91
15 0
7-18
CHAPTER 7 Specifications
Interference position (a) Base flange (b) Base rear side (c) Base
12
c)
100
R5 00
R7
R1
12
9(
145
Working envelope
50
) 3(a R5
R2
50
5 R9
145
2 12
12 2
00 R5
R7
R1 42
147
1(
c)
R4
4(
a)
100
R2
50
147
5 R9
Manipulator interference area X and Y-axis mechanical stopper positions (maximum working envelope)
M4 ground terminal User tubing 1 (6 black) User tubing 2 (6 red) User tubing 3 (6 blue) D-sub connector for user wiring (No. 1 to 20 usable)
73 55 35 0 2 0 53
7-19
CHAPTER 7 Specifications
54.5
350
122.5
R80
R2
90
96 94
70
D-sub connector for user wiring (No. 1 to 20 usable) User tubing 3 (6 blue)
57 73 80 86 166(Base size)
36
363 7 54 20
2372
48 41
0 18 -0.018
300
7-20
160
R200
110 65
R55
CHAPTER 7 Specifications
Interference position (a) Base flange (b) Base rear side (c) Base
0 12
12 0
R6 00
6 10
(a
) (c 33 R1
04 R2
50 R2
R7
8(
b)
2 12
12 2
R6
00
M4 ground terminal User tubing 1 (6 black) User tubing 2 (6 red) User tubing 3 (6 blue)
R1 24 (c)
R7 0(
73 55 35 0
b)
147
R1 96
(a R98
R2
50
147
53
0 2
7-21
CHAPTER 7 Specifications
User tubing 1 (6 black) User tubing 2 (6 red) User tubing 3 (6 blue) 58 350
126
350
R2
147
R15
(114) 106
0
70 112
75
R 76
70 106
80 93
877
683
586
376 8
50.5 45
41
2362
M121.75 Depth20
200
97
400
0 119.5
20 0
75
180
CHAPTER 7 Specifications
Interference position (a) Base flange (b) Base rear side (c) Base
0 12
12 0
(c
R7
25
00
R9 5( a)
R1
R2 10
R6
145
b) 0(
Working envelope
R3 5
145
12
12
R7
14
00
R1
99 R1
(c
R8
3(
a)
100
147
Manipulator interference area
147
M4 ground terminal User tubing 1 (6 black) User tubing 2 (6 red) User tubing 3 (6 blue) 79 61 41 0 4
R3 50
R1 45
59 0
7-23
CHAPTER 7 Specifications
User tubing 1 (6 black) User tubing 2 (6 red) User tubing 3 (6 blue) 58 350
450
126
147
R2
R15
(114) 106
0
70 112
75
R76
80 93
877
683
376 8
50.5 45
41
2362
200
97
400
0 119.5
20 0
7-24
75
180
CHAPTER 7 Specifications
Interference position (a) Base flange (b) Base rear side (c) Base
0 12
R8 0
4 R1
3(
12
a)
00
R1
62
R2
R8
17 R 4(
145
R2 59
c)
R3
50
R1
08
(b
Working envelope
145
12 3
12
(c)
47
R1
31
(a
50 R3
b) 6( R9
147
147
M4 ground terminal User tubing 1(6 black) User tubing 2(6 red) User tubing 3(6 blue) 79 61 41 0 4
59 0
7-25
CHAPTER 7 Specifications
User tubing 1 (6 black) User tubing 2 (6 red) User tubing 3 (6 blue) 58 450
550
126
147
R2
(114)
106
R76
70 106
80 93
Z-axis 200mm stroke 756 671 588 22-M40.7 Depth10 (Same on opposite side)
41
376
371 8
50.5 45
54
20
327 279
2362
200
97
400
0 119.5
20 0
7-26
75
180
70 112
R15 0
75
CHAPTER 7 Specifications
Interference position (a) Base flange (b) Base rear side (c) Base
R1 00 0
0 12
12 0
R2
30
R3
(c)
15
20
0(
a)
R4
50
6 R1
5(
b)
145
145
Working envelope
3 12
12
00
R2
R3
15 (c)
00
8 R1
4(
a)
R1
R1
49
(b)
147
147
M4 ground terminal User tubing 1(6 black) User tubing 2(6 red) User tubing 3(6 blue) 79 61 41 0 4
59 0
7-27
R4 50
CHAPTER 7 Specifications
600
600
5 R13 0
210
R2
140
150
R290
1168
60
4 69 45
95 10
20 442 390
10
161.5
7-28
R9 1
CHAPTER 7 Specifications
Interference position (a) Base flange (b) Base rear side (c) Base
9 R1
5 12
12 5
R1 20 0
R31
0 R1
150
c) 1(
7 R1
(a
1
R6
00
(b
150
Working envelope
R1
128
128
R1 20 0
3 R8
70
5 R1
(a
90 R2
(c)
00 R6
(b
152
152
M4 ground terminal User tubing 1(6 black) User tubing 2(6 red) User tubing 3(6 blue) 67 49 29 0
47 0
7-29
CHAPTER 7 Specifications
1-3
RORG YORG
RORG YORG
IO
YP YM RP RM ZP ZM ZBK YP YM RP RM ZP ZM ZBK
Round terminal Z-axis resolver Z-axis motor Z-axis brake R-axis resolver R-axis motor Y-axis arm X-axis arm
X-axis motor
IO
User tubing
User IO connector
XORG
XM YM ZM RM XY ZR
Robot cable
7-30
CHAPTER 7 Specifications
Machine harness
RORG YORG
RORG YORG IO
YM YP ZBK ZM ZP RP RM
YM YP ZBK ZM ZP RP RM R-axis resolver R-axis motor Z-axis resolver Z-axis motor Z-axis brake Y-axis resolver Y-axis motor Round terminal
Y-axis arm Y-axis origin sensor X-axis arm X-axis motor X-axis resolver XP XM YM YP ZM ZP RM RP ZBK YORG RORG FG FG XP
IO
XORG
XM YM
XORG
User tubing
User IO connector
XM YM ZM RM XY ZR
Robot cable
7-31
CHAPTER 7 Specifications
User tubing
User IO connector
RORG YORG RORG YORG YM YP IO
YM YP
ZM ZBK ZP
ZM ZBK ZP
Y-axis motor
RM RP
RM RP
Z-axis motor
M4 ground terminal
Fan
X-axis motor
X-axis resolver
XP XP
XORG
XM
XM
Round terminal
Fan
FAN1 FAN2 YM
FAN
ZM RM YP ZP
ZORG
RP YORG
RORG ZBK FG
YM ZM RM
FG LMT LMT ZR XY
Robot cable
CHAPTER 7 Specifications
1-4
Wiring table
Robot cable wiring table
Signal Resolver S2 S4 S1 S3 R1 R2 DG Resolver S2 S4 S1 S3 R1 R2 DG FG FG YP XP Connector No 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 Connection No Connector 1 2 3 4 5 6 7 19 20 21 22 23 24 25 18 36 HLIM GND24 HLIM GND24 Origin Sensor GND ORG 24V Origin Sensor 24V ORG GND U V W FG U V W Round terminal YM 1 2 3 XM YORG XORG 3 2
1 1
Color
Blue Orange Green Brown Gray Red Green Black Yellow
Wire 0.15sq Twisted pair 0.15sq Twisted pair 0.15sq Twisted pair 0.3sq 0.15sq Twisted pair 0.15sq Twisted pair 0.15sq Twisted pair 0.3sq
XY
10 11 28 29 13 12 9 27 30 31 2 3 4 1 2 3 4 YM XM
Green
0.3sq 0.3sq
Green
Twisted pair Twisted pair 0.15sq 0.75sq 0.75sq 0.75sq 0.75sq 0.75sq 0.75sq
2 3
1
2 3
7-33
CHAPTER 7 Specifications
Connector No 1 2 ZP 3 4 5 6 7 ZBK 1 2
Connection
No Connector 1 2 3 4 5 6 7 14 16 15 17 ZR
Color
Blue Orange Green Brown Gray Red Green Black Yellow Pink Purple White Blue/Red
Wire 0.15sq Twisted pair 0.15sq Twisted pair 0.15sq Twisted pair 0.3sq 0.15sq Twisted pair 0.15sq Twisted pair 0.15sq Twisted pair
Resolver
S2 S4 S1 S3 R1 R2 DG FG FG RP
1 2 3 4 5 6 7 1
19 20 21 22 23 24 25 18 36
Orange/White 0.15sq Green/White Twisted pair Brown/White 0.15sq Gray/White Green Red/White
Black/White 0.15sq
HLIM GND24 HLIM GND24 Origin Sensor 24V ORG GND U V W FG Round terminal U V W RM 1 2 3 ZM RORG
1
10 11 28 29 27 30 31 2 3 4 1 2 3 4 RM ZM
Green
0.3sq 0.3sq 0.15sq 0.15sq 0.75sq 0.75sq 0.75sq 0.75sq 0.75sq 0.75sq
Green
White/Blue Blue/Red2
2 3
1
2 3
7-34
CHAPTER 7 Specifications
0.75mm2
0.75mm2
0.3mm2
0.2mm2
IO
IO
0.2mm2
Frame ground Frame ground Origin Sensor 24V ORG GND Origin Sensor 24V ORG GND
YORG
RORG
Round terminal Round terminal
Green Green White YORG Purple Gray White RORG Blue Gray Round terminal Yellow/Green Round terminal Blue FG
7-35
CHAPTER 7 Specifications
Machine harness wiring table (YK500X, YK600X, YK700X, YK800X, YK1000X, YK1200X)
Y-axis arm side Signal Y-axis Resolver S2 S4 S1 S3 R1 R2 DG Z-axis Resolver S2 S4 S1 S3 R1 R2 DG R-axis Resolver S2 S4 S1 S3 R1 R2 DG Y-axis motor U V W Z-axis motor U V W R-axis motor U V W Z-axis brake Z-axis brake 1 2 ZBK RM ZM YM RP ZP YP Connector No 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 2 3 1 2 3 1 2 3 1 2 1 2 3 4 5 6 7 8 9 10 11 User signal line IO 12 13 14 15 16 17 18 19 20 21 22 23 24 Frame ground Frame ground Origin Sensor 24V ORG GND Origin Sensor 24V ORG GND Round terminal Round terminal RORG YORG 1 2 3 1 2 3 25 Connection No Connector 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 2 3 1 2 3 1 2 3 1 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 1 2 3 1 2 3 RORG YORG FG IO ZBK RM ZM YM RP ZP YP Brown White Red White Orange White Green Brown Black Red Black Orange Black Green Brown Gray Red Gray Orange Gray Green Brown Red Orange Blue Purple Gray Black White Brown White Black Brown Red Orange Blue Purple Gray White Black Brown Red Orange Blue Brown Red Orange Blue Purple Gray White Black Brown Red Orange Blue Green Green Brown Red Orange Brown Blue Orange Round terminal Yellow/Green Round terminal Black 0.75sq 0.75sq 0.2mm2 0.2mm2 Shield Shield 0.2mm2 0.2mm2 0.3mm2 0.75mm2 0.75mm2 0.75mm2 Base side Color Wire 0.2mm2 Twisted pair 0.2mm2 Twisted pair 0.2mm2 Twisted pair Shield 0.2mm2 Twisted pair 0.2mm2 Twisted pair 0.2mm2 Twisted pair Shield 0.2mm2 Twisted pair 0.2mm2 Twisted pair 0.2mm2 Twisted pair Shield
7-36
CHAPTER 7 Specifications
Y-axis Resolver S2
1 2
Z-axis Resolver S2
S4 S1 S3 R1 R2 DG
R-axis Resolver S2
S4 S1 S3 R1 R2 DG
IO
11 12 13 14 15 16 17 18 19 20
Y-axis motor
U V W
Z-axis motor
U V W
R-axis motor
U V W
25
Frame ground
7-37
CHAPTER 7 Specifications
Connection
No. 1 2 3 4 5 6 7 1 2 3 1 1 2
Connector
Resolver
XP,YP,ZP,RP
Motor
Round terminal
Brake
Yellow Yellow
7-38
MEMO
User's Manual
YK-X series
SCARA Robot
Dec. 2009 Ver. 5.21
This manual is based on Ver. 5.21 of Japanese manual.
YK-X/XH