Recommendations To Check AC Electric Motors
Recommendations To Check AC Electric Motors
Recommendations To Check AC Electric Motors
+61 (0) 402 731 563 +61 (8) 9457 8642 info@lifetime-reliability.com www.lifetime-reliability.com
If you want to learn more about best practice machinery maintenance, or world class mechanical equipment maintenance and installation practices, follow the link to our Online Store and see the Training presentations and Books there http://www.lifetime-reliability.com/store/machinery-maintenance-andinspection/store-machinery-maintenance.html
How can designers optimize service life and productivity when selecting and applying ac motors [1]
If an application demands several starts and stops then the peak current must be considered due to heat generated in the windings. This heat must be removed from the motor through its surface, but amount dissipated depends on the ambient surroundings. Elevated temperatures can also be a reflection of the load to rotor inertia. One way to reduce this inertia mismatch is by adding ratio via a gearbox. Successful motor operation depends on defining application speed, torque, reflected inertia, and time.
+61 (0) 402 731 563 +61 (8) 9457 8642 info@lifetime-reliability.com www.lifetime-reliability.com
60034-30. Four efficiency classes are proposed, namely Standard Efficiency (IE1), High Efficiency (IE2) equivalent to EPAct, Premium Efficiency (IE3), and Super-Premium Efficiency (IE4).
Assembly
Ensure all mating parts are clean. Cleaning can be done with a magnet, vacuum cleaner or dry compressed air [3]
Installation
Choice of Voltage [4]
Accepted good practice is to keep the difference in voltage between the point at which power is and the motor terminals below 3 percent when the motor is delivering full load delivered from the utility. Nominal Voltage (V) 120 120/208 240 480 600 2400 Nameplate voltage (V) Polyphase Motors Single-phase motors 110 115 208 or 220 115 220 230 440 460 550 2300 -
Foundations [5]
A rigid foundation is essential for minimum vibration and proper alignment between motor and load.
Mounting [5]
A motor can be mounted in many ways, depending upon its size, weight, and use. Small motors may incorporate a rigid mount, with the frame welded directly to a steel plate formed to match the shape of 2
+61 (0) 402 731 563 +61 (8) 9457 8642 info@lifetime-reliability.com www.lifetime-reliability.com
the frame and incorporating mounting holes. Most commonly, medium- and large-size motors have mounting feet cast integrally with their frames. Vertical motors require an end bell specially machined to receive a mounting flange. Where it's important to isolate vibration and noise or to reduce the shock of starting and stopping, various types of resilient mounts and cushion bases are available. After aligning the motor with the load, you can bolt the motor in place with maximum size bolts. It's advisable to provide some dimensional variance in the location of the foundation bolts. This can be done by locating the bolts in a steel pipe embedded in the foundation. NEMA standards give dimensions for foot mountings and some flange mountings. Sliding bases and adapters are available for use with Tframe motors when they replace old U-frame motors. Make sure you check whether other components or equipment such as gears, special couplings, or pumps are to be mounted on the motor. If so, be sure space is available. After the motor base is in place but before it is fastened, you should shim as required to level the base. Use a spirit level (check two directions at 90 degrees) to ensure that motor feet will be in one plane (base not warped) when base bolts are tightened. Then, set the motor on the base, install nuts, and tighten. Do not make a final tightening until after alignment.
Operating
How can end users optimize service life and productivity from the ac motors on their machines [1]
Users must pay attention to their motor bearings to prevent premature failure. This involves re-greasing with compatible grease as defined by the manufacturer. Strict adherence to shaft alignment and motor mounting procedures reduce shaft breakage, vibration, and bearing failure. Routine maintenance every 6 months ensures the surrounding area has not degraded. Make sure all protected guards, gaskets and other protective means are in good working order.
Maintenance
Visual and mechanical inspections [6]
An important aspect of large machine maintenance is the visual and mechanical inspection. 1. Inspect the machine's physical and mechanical condition. Check for signs of oil or water leakage. Verify that air inlets are not plugged. Check for abnormal sounds or smells. Check the water and oil supply piping. 3
+61 (0) 402 731 563 +61 (8) 9457 8642 info@lifetime-reliability.com www.lifetime-reliability.com
Check the drain piping. Look at the condition of the foundation, grout, bed plates, anchor bolts, shaft extensions, couplings and guards. Check the surroundings for any environmental issues that may affect performance or service life.
2. Inspect anchorage, alignment and grounding of the motor, driven equipment and base. 3. Inspect air baffles, filter media, cooling fans, slip rings, brushes and brush rigging. 4. Inspect bolted electrical connections for high resistance. 5. While the unit is under full load, perform a thermographic survey. 6. Perform special tests such as air-gap spacing and machine alignment, if applicable. 7. Verify the application of appropriate lubrication and lubrication systems. Verify the bearing oil level. Check for improper lubrication, oil of the wrong type, viscosity that is too heavy or too light. Verify that there is sufficient oil in bearing bracket to cover bottom of rings. Look for dirty oil or old oil (should be replaced and/or tested). Verify that the oil rings are turning (especially at low temperatures). Check for water or other contamination within the lubrication system. Verify that the feed oil is connected to the correct ports When the bearing and seals are inspected the following should be considered: Check for excessive bearing clearance. Verify seal clearance and condition. Make sure there is not improper seating of shaft journal in bearing or a bent shaft. 8. Verify the absence of unusual mechanical or electrical noise or signs of overheating. Check for pitting of bearing and journal surfaces due to bearing currents. Verify integrity of bearing insulation. Make sure there are no rough bearing surfaces due to corrosion or careless handling. Verify that there is not excessive end thrust from the mechanical load. 4
+61 (0) 402 731 563 +61 (8) 9457 8642 info@lifetime-reliability.com www.lifetime-reliability.com
Check for poor alignment. Make sure that the bearing Babbitt has not been fractured or damaged due to impact or shock loading of the bearing journal.
9. Verify that resistance temperature detector (RTD) circuits conform to drawings and are functioning properly.
+61 (0) 402 731 563 +61 (8) 9457 8642 info@lifetime-reliability.com www.lifetime-reliability.com
NEMA MG 1-2.05
ANSI/NETA MTS-2007
Energy Management Guide for Selection and Use of Fixed Frequency Medium AC Squirrel-Cage Polyphase Induction Motors Standard for Maintenance Testing Specifications for Electrical Distribution Equipment and Systems
Provides practical information concerning proper selection and application of polyphase induction and synchronous motors, including installation, operation and maintenance.
References
1. 2. 3. 4. 5. 6. Eitel, E., AC motors. Career and Technical Education, 2005. Almeida, A., et al., Electric Motor Standards, Ecodesign and Global Market Transformation. Lawrie, Guidelines for effective motor installation. 1984. Lamkey, F.R., The Electric Motor Book. 1961, The Penton Publishing Co: New York. p. 77-99. Lawrie, R., Guidelines for motor installations. 1996. Widup, R., Large Motor Maintenance: Basics for machine reliability. 2008.
You can learn a lot more about rotating equipment health management with the 4-day Rotating Machinery Maintenance and Reliability Training Course PowerPoint Presentation available to buy at the Lifetime Reliability Solutions online Web store.