GT 0313
GT 0313
GT 0313
Automotive Getting Sincerely Plastic My Gears Are Bigger than Your Gears THE OSU GearLab:
TECHNICAL
MAR/APR
2013
INDUCTION HEAT INNOVATION UPDATE HEAT TREAT AUDIT? NO SWEAT! DUAL-CLUTCH GEARBOX SHAFT OPTIMALLY PROCESSED ASK THE EXPERT:
www.geartechnology.com
Phone: 847-649-1450 5200 Prairie Stone Pkwy. Ste. 100 Hoffman Estates IL 60192
Review the specications , watch a video and request a quote by visiting our website or give us a call and request a presentation.
www.star-su.com/dynamic sales@star-su.com
contents
MAR/APR
38
2013
47 30
features
24 Job Shop Lean
Strategies for assembling continuous improvement teams. Gear market offers opportunities for ingenuity and innovation.
technical
56 Ask the Expert
Workholding
58 Producing Large-Sized, Skew Bevel Gear Pinion Using Multi-Axis Control and Multitasking Machine Tool
How to manufacture replacement skew bevel pinions using multi-axis and multitasking machine tool.
Automotive and the plastics industry now all-in. Industry battles it out for worlds largest gear title. Where ideas and research flourish.
70 How to Conduct a Heat Treat Audit 72 Optimization of a Process Chain for Gear Shaft Manufacturing
Maximizing efficiency by choosing the right processes.
52 OSU GearLab
Vol.30, No.2 GEAR TECHNOLOGY, The Journal of Gear Manufacturing (ISSN 0743-6858) is published monthly, except in February, April, July and December by Randall Publications LLC, 1840 Jarvis Avenue, Elk Grove Village, IL 60007, (847) 437-6604. Cover price $7.00 U.S. Periodical postage paid at Arlington Heights, IL, and at additional mailing office (USPS No. 749-290). Randall Publications makes every effort to ensure that the processes described in GEAR TECHNOLOGY conform to sound engineering practice. Neither the authors nor the publisher can be held responsible for injuries sustained while following the procedures described. Postmaster: Send address changes to GEAR TECHNOLOGY, The Journal of Gear Manufacturing, 1840 Jarvis Avenue, Elk Grove Village, IL, 60007. Contents copyrighted 2013 by RANDALL PUBLICATIONS LLC. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system, without permission in writing from the publisher. Contents of ads are subject to Publishers approval. Canadian Agreement No. 40038760.
[www.geartechnology.com]
Havlik Gear Inc. offers start to finish service on large and small gearing projects such as customer drawings and specs, design services, and gear cutting or machining. Visit www.havlikgear.com for more information.
Todays customers demand high quality custom gearing at competitive prices and lead times. We recognize the Niles ZP40 as the machine which gives us maximum flexibility while maintaining the highest level of quality and efficiency possible. Our ability to grind and inspect large internal and external gears has definitely given us the ability to enter new markets such as Wind Energy, Marine, Rail, and Defense. The machine is well built, user friendly, consistent and reliable. Niles offers very prompt service and support. We recommend Niles Machines to any gear shop. Havlik Gear
KAPP Technologies 2870 Wilderness Place Boulder, CO 80301 Phone: (303) 447-1130 Fax: (303) 447-1131
www.kapp-niles.com info-usa@kapp-niles.com
contents
Vol.30, No.2
departments
09 Publishers Page 11 Voices
Turn Off the Noise Design for Manufacturability Crucial for Gear Industry Success New from Vargas; Hexagon Announcements, whats hot, more APRIL: H annover Messe; Gear Design and Theory; AGMA/ABMA Annual Meeting MAY: Gear Manufacturing and Inspection Sign up or renew; its free! Every advertiser in this issue Our products and services marketplace How Gear Hobbing Works
14 Product News
78 Industry News
84 Events/Calendar
85 Subscriptions
86 Advertiser Index
Toolholding Workholding Sub-contract Machining
87 Classifieds
88 Back-To-Basics
Over 50 years experience in the design and manufacture of expanding mandrels and collet chucks
More precise and versatile than solid mandrels or similar workholding Quick and secure clamping Interchangeable sleeves, in a range of sizes, to cover a family of components Suitable for almost all machining & inspection procedures Collaborating with the worlds finest
www.chevintools.com Toll Free: 1 877 4 CHEVIN (847) 690 1278
MAR/APR
INDUCTION HEAT INNOVATION UPDATE HEAT TREAT AUDIT? NO SWEAT! DUAL-CLUTCH GEARBOX SHAFT OPTIMALLY PROCESSED ASK THE EXPERT:
www.geartechnology.com
Exhib
it: Gea
r Sha
Liebherr Gear Technology, Inc. 1465 Woodland Drive Saline, Michigan 48176-1259 Phone.: +1 734 429 72 25 E-mail: info.lgt@liebherr.com www.liebherr.com
The Group
05.03.13 18:5
New products and technologies from Dayton Progress, Oelheld, TechnoSommer, Klber Lubrication and Cimcool demonstrate the latest lubrication innovations including high-performance greases, grinding fluids, dispensing systems, coatings and advanced industrial fluids in the February Gear Technology E-Newsletter: www.geartechnology.com/newsletter/0213/lube0213.htm
(847) 437-6604
Editorial
Publisher & Editor-in-Chief Michael Goldstein publisher@geartechnology.com Associate Publisher & Managing Editor Randy Stott wrs@geartechnology.com Senior Editor Jack McGuinn jmcguinn@geartechnology.com Senior Editor Matthew Jaster mjaster@geartechnology.com Editorial Consultant Paul R. Goldstein Technical Editors William (Bill) Bradley Robert Errichello Octave Labath, P .E. Joseph Mihelick Charles D. Schultz, P .E. Robert E. Smith
LinkedIn:
In response to Senior Editor Jack M c G u i n ns article on NDT Testing for Big Gears in the January/February issue of Gear Technology, Tom Shumka, president of Global Inspections-NDT, Inc. discusses a new method for NDT on large gears. ASTM E2905 uses Electromagnetics for this NDT method. It is fast and efficient
and all data can be electronically archived for future trending. To contact Shumka on this subject e-mail at tom@global-ndt.ca. The Star PTG-6L Tool Grinder was also featured on Gear Technologys LinkedIn Group Page. Engineered to manufacture complex cutting tools the new Star PTG-6L tool and cutter grinder is a five axis, CNC controlled cutter grinder for manufacturing, sharpening and reconditioning a wide variety of cutting tools (http://info.star-su.com/ ptg-6l)
design
Art Director David Ropinski dropinski@geartechnology.com Associate Publisher & Advertising Sales Manager Dave Friedman dave@geartechnology.com Materials Coordinator Dorothy Fiandaca dee@randallpublications.com
ADVERTISING
CIRCULATION
Stay Connected
Follow us on Twitter twitter.com/#!/Gear_Technology
Circulation Manager Carol Tratar subscribe@geartechnology.com President Michael Goldstein Accounting Luann Harrold
RANDALLSTAFF
A video currently on our website from Hauer Helicopter shows single point cutting of a spiral bevel crown gear on a three-axis CNC milling machine. www. youtube.com/watch?v=bKnHOyDWeh0.
[www.geartechnology.com]
the latest advancements in manufacturing technology for the production of large precision gears and gear related components await your demanding applications in our new manufacturing facility located in yorktown, indiana.
internal ring gears: Spur and helical to 2.4-meter diameter size with modules up to 30 max. Processes include gear shaping, internal milling (gashing) and gear grinding. external gears: Spur and helical to 1.6-meter diameter size with module up to 35 max. Processes include gear hobbing, external milling (gashing) and gear grinding. Large turning capacity: Maximum diameter 2.8 meters. Modern vertical CNC turn/ mill center offering exceptional capabilities for producing large planet carriers.
deep-case carburizing: 8,800 lb capacity Integral Quench Batch Furnace, Shot-Blasting, Complete Materials Laboratory. Metrology Laboratory: CNC Analytical Gear Inspection capabilities to 3-meter diameter size via Gleason 3000-GMM, Large Capacity Zeiss 30/40/30 CMM. Large gearbox assembly capabilities: Modern Manufacturing Facility including significant overhead crane capacity for transporting heavy components and assemblies.
For your inquiries, contact: dale e. harder (765) 759-2128 dale.harder@brevini.com Brevini Wind usa, inc 2400 N. Priority Way Yorktown Indiana, 47396 / USA Phone +1 765 759 2125 Fax +1 765 759 4728 breviniwind.us@brevini.com
WWW.BREVINIWINd.COm
Downtime is a black hole that impairs productivity, kills the bottom line and simply shouldnt happen due to breakdowns. With a philosophy of continuous process improvement, in conjunction with an active reliability and maintainability program, Mitsubishis gear machine products deliver best in the business quality and predictable production. Experience perfect production systems by visiting www.mitsubishigearcenter.com or contact sales 248-669-6136.
publisher's page
Trying to figure out whats going on in this crazy economy of ours seems a bit like reading tea leavesone part pseudoscience and three parts wild conjecture. Of course some pundits are telling us that
Another gear manufacturer I spoke with specializes in gears for mining, energy and heavy industry. Although all of those markets are either down or stagnant, he still felt positive about his business moving forward. In his case, over the past couple of years, business had been strong enough that a significant amount of work was farmed out overseas. But now that things have slowed down, much of the previously outsourced work is being brought back home. Also, the energy industry seems to be in an unusual place. For example, the fracking industry has put a hold on gearbox orders for compressorsnot because the demand has dissipated, but because the industry needs to wait for pipelines to be built. Those orders should come back strongly in 2014, this manufacturer says. Finally, I spoke with a gear manufacturer who specializes in aerospace gearing. According to him, business remains very strong despite Defense Department cuts and the European crisis. So many programs are already in place that theyll be busy filling those orders for several years. A theme that kept coming up in my conversations was the fact that U.S. manufacturers and the American economy are well positioned with regards to the supply of energy. Our natural gas costs 25 percent of what it costs outside North America, and our oil costs 80 percent of world prices. Lower energy costs reduce overall manufacturing costs, especially for the chemical and heat treat industries. Within 5-7 years, many expect North America to be a net exporter of energy, with perhaps the largest reserves of energy in the world. After speaking with all of these suppliers, I feel a lot better. I know that some of the core businesses that support gear manufacturingautomotive and aerospaceare going strong. Other industries that play a big role, such as energy, off-highway and farm equipment, will likely come back stronger in the second half of 2013 and the first half of 2014. So turn off your televisions and your radios. Shut down your browsers, your apps and your streaming news feeds. Do whatever it takes to quell the barrage of headlines and opinions that compete for your attention. Once youve eliminated the noise, listen to your customers. Thats what I did.
Stronger
Just like gears, induction heating is all about precision. Inductoheats precision controlled, induction gear hardening systems provide ideal metallurgical patterns, minimum shape distortion, increased wear resistance and exceptional contact fatigue strength. No matter the size or shape of your gear, our induction systems are designed specifically to produce Stronger long lasting parts time and time again.
Inductoheat caters to your induction heating needs: Process development Single part process monitoring Metallurgical analysis Single-shot, scanning, tooth by tooth Single-coil dual-frequency technology Wide range of gear & bearing diameters
Inductoheat, Inc. Madison Heights, MI (248) 585-9393 www.inductoheat.com
voices
issues that could have been avoided are identified very late in the process that impact production costs and schedules. This suggests that key DFM principles are often underutilized in practice and are not applied consistentlyor to the degree necessaryto avoid these negative results. By considering in detail three DFMbased best practices, we can offer insight for improving the conditions for success as manufacturing partners work together towards a common goal. Engaging key stakeholders in an organized team from the very start of a project, conducting a thorough feasibility study, and implementing the proper quality assurance tools will help ensure that the final
product is reliable, manufacturable and acceptable to the original equipment manufacturer (OEM) andend user.
For DFM to be successful, it is vital to create a truly integrated multi-disciplinary design and product development team from the beginning. This team should include representatives from key departments that will be involvedfrom design through productionincluding engineering; product management; manufacturing; quality; sales and marketing;
A DFM approach can produce significant benefits even from the smallest details; for example, where a change to a gear tolerance by .002" can significantly improve the performance of a device.
supply chain; and others appropriate to a given project. In addition, it makes sense to include representatives from outside your business, such as key suppliers and other design and manufacturing specialists who may be needed on a specific project. Good collaboration here can help ensure that an elegant gear or motion control design is practical to manufacture and meets the cost targets and performance goals set by the end user. An integrated team also reduces the risk of a silo approach where one element may be overemphasized while other design considerations are overlooked. All critical customer requirements must be clearly established during initial team meetings, as total project lifecycle costs and speed to product launch are often defined early in the process. A good multi-disciplinary team looks at details such as materials selection, degree of manufacturing difficulty, supply chain issues and market/industrybased requirements such as regulatory stipulations. Consulting early on with key suppliers can help in avoiding costly rework later. For example, Precipart recently reviewed the design of a tight tolerance gear assembly for a medical imaging device, and we identified a potential performance flaw early in the design phase. As a result we recommended bench assembly and light run-in to create the contact pattern on a helical gear to reduce
March/April 2013|GEAR TECHNOLOGY
11
voices
backlash by approximately .002", which would significantly improve the durability, performance and lifecycle of the device. The dynamics and open communication of a multi-disciplinary team are crucial to ensuring successful DFM processes. A senior staff engineer from a medical device manufacturer recently told us, The level and degree of DFM teams vary, but from the design phase perspective, suppliers who are critical to the projects success should be included in the discussions, and the sooner the better. We receive great input from our suppliers in their fields of expertise, and having a good partnership with them ensures the launch is successful. inaccuracies in the system. Envelope size and weight may be other key considerations for aerospace applications, due to space and weight constraints on the aircraft. These critical design and application requirements must be captured up front as inputs for the integrated product development team. A thorough feasibility study will also help identify concerns about production tooling i.e., whether existing tooling is sufficient or if custom tooling is needed. It can also assess the tolerance of materials for post-fabrication treatments such as deburring. Poorly finished parts are frequently a cause of order rejection and production delays. The feasibility study can help identify areas of dimensional inaccuracies and rough surfaces that can lead to noise, excessive wear and backlash between the pair of gears in mesh, which can result in inefficient power transmission. After reviewing these factors, the DFM team can implement design or manufacturing alternatives that prevent these problems from occurring. A comprehensive assessment will utilize computer-aided modeling and analysis techniques to determine load values and directions, life expectancy, heat treatment specifications and tolerance areas such as stack-ups, backlash and hysteresis. Collaborating with partners that have both high-precision manufacturing capabilities and design services to conduct feasibility studies through-
Feasibility Study
A comprehensive feasibility study is part of an effective DFM process and it should examine key specifications and potential design issues that may occur throughout the life of the gear or motion control device; it should also offer recommendations to address any performance issues in various environments and conditions. Application-specific requirements are fully evaluated in the feasibility study. For example, some aerospace applications may focus on torque and speed, while others focus on accuracy. A gearbox which controls the positioning feedback system of an aircrafts landing gear must utilize anti-backlash gears to avoid
All critical customer requirements must be clearly established during initial team meetings, as total project life cycle costs and speed to market are often dictated during early design stages.
Quality initiatives such as risk management and Six Sigma can help reduce variation and remove waste from the manufacturing process. An effective DFM process takes these types of quality initiatives into account up front to help build quality into the design and mitigate risk in the production of new gears or motion control devices. Risk management utilizes several techniques to identify all the criticalfactor project elements. The design of experiment (DOE) is one example. As a methodology for systematically applying statistics to experimentation, it is used to identify the source of variation in processes such as manufacturing. DOE is critical in evaluating or validating a component or procedure and helps ensure that a product functions as intended, without costly testing and revision while in production. Despite its high value, DOE methodology is often overlooked in the rush to get a project moving. Another key risk management process is the failure mode and effect analysis (FMEA). It is difficult to have a success[www.geartechnology.com]
12
Conclusions
Successful delivery of gears and motion control devices requires more than a sophisticated design. Design for manufacturability ensures that innovative technology delivers true economic value while guiding the development process, as well as the teams responsible for achieving success, so that the new gear or motion control device can be produced cost-effectively, brought to market with minimal delays, and perform reliably.
Here the PECo ND300 analytically inspects and evaluates elemental gear attributes, verifying the quality and precision of tight tolerance gears.
engineering and chief operating officer at Precipart, where he has worked for 18 years managing the engineering and design teams.
dmori1470-2_april_ads_idays_GT.indd 1
2013
www.dmgmoriseikiusa.com
3/8/13 2:10 PM
13
product news
Vargus USA
TMSD gear milling tools solved all of the customers needs for the application. First, the price was five percent cheaper than the cost of the current hobbing methods. Secondly, the productivity of the TMSD was almost 75 percent faster than the current tooling. Third, the reliability met all class requirements for the spline. The customer was very happy and all the requirements of the test satisfied. Subsequent orders have been placed, says Joe Magee, gear milling product manager. The main improvem e nt s t h e c u s t om e r received as an added bonus, but did not expect were the
tool life and part finish both were considerably better than the current method. The finish was better than a 64 Ra (roughness average), competition was 125 at best, 250 on average, Magee says. As for the overall project summation the customer was able to move the parts from a secondary operation on a hobbing machine to the part they were now completing on their machining center; reducing handling, extra set up and utilization time on the extra operations. The Vardex Gear Mill is suitable for medium and large batch size spline and gear manufacturing and is faster, simpler, easier to use and much more economical than existing HSS/HSS PM cutters. With its state-of-the-art design of PVD coated fine substrate carbide, the Gear Mill offers absolute price/performance advantage over existing technology. TMSD is suited to the machining of both straight and helical teeth gears, and gear modules from 1 mm to 6mm. All materials can be accommodated, from very soft to hardened steels of 60 HRC. Each insert profile in the TMSD portfolio is supplied with the appropriate module shape of one, two or three cutting corners (special forms can be supplied), and the ability to achieve a full profile in accordance with Class 7 DIN 3962. Importantly, because the tooling focuses on carbide inserts located in standard tool bodies for end, shell and disk milling on three-axis
CNC milling machines (the cutting edge is subject to relatively low loads), TMSD is affordable for companies of every size across all industry sectors. This is in stark contrast to the usual need for ultra-expensive hobbing machines and tooling (which also needs recoating after regrinding) with their inherent lengthy set-up times. Likewise, traditional milling disks are often only suitable for rough machining on softer materials. TMSD, therefore, alleviates the cost and potential quality problems for many companies where relatively small batches do not justify the expense of a dedicated machine and for manufacturers, especially, the TMSD route eliminates the cost and time
involved with sub-suppliers. The benefits of Vargus TMSD tools are clear: in one case, involving a 40.5 mm diameter 42CrMoS4V gear with 52 teeth, a TMSD milling operation took just five seconds to produce each slot. TMSD also produced similar savings in one spline milling application, reducing gear rack production from 10.7 min to only 3.3 min. Similar benefits have also been achieved with plastic gears.
14
[www.geartechnology.com]
Hexagon Metrology
15
product news
Emuge
precise cNc measuremeNts taKes mOre tHaN a great cmm. it taKes valued service aNd suppOrt.
The forming of threads offers many advantages over conventional thread cutting. A formed thread is one where the material has been displaced instead of cut, which provides suitable thread surface quality and increased static and dynamic strength of the thread. Additional benefits include eliminating the risk of poor threads due to axial miscutting and the ability to increase tapping speeds. Our MultiTAP line is the result of collective years of Emuges extensive tapping expertise, application research and a challenge the company issued to its engineers to design a multi-purpose tap. Emuge design engineers responded by choosing a select base material along with special geometry and surface treatment that would work in as many common materials and applications as possible, stated Matysiak. All MultiTAP-Form Taps are made with Emuges trademark long shanks, which are DIN length, designed for extra reach. Tap sizes include a range for UNC or UNF threads, from #4-40 to 3 8-24 inch sizes, to metric sizes from M40.7 to M101.5.
cmm vision form and finish precision tools and instruments data management
16
[www.geartechnology.com]
Mahr Federal
17
12/22/11 9:50 AM
product news
Sandvik Coromant
Releases CoroChuck 930
CoroChuck 930 is a high-precision hydraulic chuck from Sandvik Coromant for milling and drilling operations. The secret behind the high-precision and pull-out security is in the optimized design of the brazed membrane that allows for maximum, secure clamping with two supports on each side (fulcrums). This design ensures suitable torque transmission to improve the performance of solid carbide end mills, drills and reaming tools. This performance is repeated over multiple clamping cycles to retain high-quality component surfaces and extend tool life. Additionally, the CoroChuck 930 is designed with damping features that minimize vibrations during the machining process. Based on a hydraulic tool clamping system, the CoroChuck 930 can be quickly tightened or released with a dedicated torque wrench, thus improving efficiency through quick and easy set-ups and changes. No external equipment is required to clamp or unclamp the system. The chuck holds tolerances within microns to improve tool precision, surface finish and productivity. The precision run-out can be measured at <4 m (157 inch) at 2.5 DC. CoroChuck
930 is suitable for all types of machine tools that either have a rotating spindle or workpiece; lathes, multi-task machines, machining centers and driven tools in turning centers and vertical turning lathes. Available in pencil, slender and heavy duty design, CoroChuck 930 is balanced according to DIN 69888.
Heidenhain
18
Hardinge
The quality and precision of our Broaches, Shaper Cutters and Gears have won customers world-wide from the smallest gear shop to NASA and the Mars Rover.
& Shaper Cutter Broach manufacturing & repair & Spline Gear prototype to production Master Gears & Gages Small & fine pitch
LS
&
DEDICATED TO EXCELLENCE
1605 Industrial Drive Auburn, CA 95603 Phone: (530) 885-1939 Fax: (530) 885-8157 Web: www.broachmasters.com Email: info@broachmasters.com
19
product news
nitride-based WIS10 (Sialon ceramic) and WWS20 with silicon carbide whiskers (whisker ceramic), stand up to these applications with increased tool life and process reliability. They are designed to deliver cutting speeds five to ten times higher than carbide in many super-alloy roughing and semi-finishing operations. With its self-reinforced structure of silicon nitride ceramic and enhanced chemical stability, WIS10 offers excellent notch wear resistance and excels at turning all types of heat-resistant super alloys. The application area for WIS10 ranges from light roughing to semi-finishing operations. The new WWS20, for its part, delivers superior fracture resistance thanks to its silicon carbide whisker fibers, which add the toughness needed to handle interrupted cuts. This makes it suitable for turning forged or cast out-of-round workpieces with uneven surfaces or heavy interruptions, and for high feed rates used when removing large amounts of material. In addition, WWS20 excels at turning hardened steel. Walter supplies WIS10 and WWS20 indexable, ceramic turning inserts in the negative basic shapes C, D, R and S, and positive basic shape inserts in RC and RP format; all are available with different cutting edge designs. For turning there are also tool-holders available with carbide shoe and clamping system. This gives the user the best possible tool-holder system for turning, capable of cutting speeds up to 1350 sfm.
20
[www.geartechnology.com]
For gears they can rely on, partner with a heat treater that you can rely on.
At Solar Atmospheres, your critical specs get the specialized expertise they deserve. From stress relief to case hardening, well help assure that your gears can go the distance. Precise carbon control and aerospacequalified pyrometry produce uncompromised quality. Harness our leading-edge vacuum technology to improve the uniformity of your case depths, minimize distortion and enjoy clean parts with no IGO (intergranular oxidation). ISO 9001 / AS 9100, Nadcap accredited.
Vacuum Heat treating Brazing CarBurizing nitriding
www.solaratm.com 1-855-WE-HEAT-IT
product news
for stock and MTO plastic parts. Martin now manufactures stock gears & sprockets in Nylon and UHMW. Made-to-orders manufactured in a variety of materials, sizes and shapes. Milled plastic quanties 1 to 1000 pieces, injection molding available for larger quantities. Send us your drawings, we would love to quote your next project. For more information contact:
shorten lead times using these machines. The Hyper Quadrex 150MSY and Vertical Center Universal 400-5X both feature Mazaks new Matrix 2 CNC control that uses advanced technology to provide extremely fast processing speed, excellent cornering, suitable part surface finishes and reduced cycle times. Furthermore, the CNC control brings unbeatable accuracy and increased productivity to highly complex applications requiring multi-tasking operations; full, simultaneous fiveaxis machining; and the incorporation of automation. Because it easily pairs with bar feeder systems and workpiece unloaders, as well as gantry robot loaders, the Hyper Quadrex 150MSY enables shops to achieve long periods of unmanned operation over breaks, nights and weekends. Such automation places the machine in automation Levels 1 and 2 of the 3-4-5 solution. The Vertical Center Universal 400-5X accommodates articulated robots, placing it in automation Level 4 of the 3-4-5 solution. Articulated robots are a highly advanced alternative to traditional production and enable shops to fully automate the machines load and unload operations.
www.martinsprocket.com/plastics.htm 817-258-3000
22
1/9/13 3:36 PM
[www.geartechnology.com]
www.ALD-Holcroft.com
feature
JOB
Dr. Shahrukh Irani, Director IE Research, at Hoerbiger Corporation of America
LEAN
SHOP
Eds Note: This is the second article in an eight-part reality series on implementing Continuous Improvement at Hoerbiger Corporation. Throughout 2013, Dr. Shahrukh Irani will report on his progress applying the job shop lean strategies he developed during his time at The Ohio State University. These lean methods focus on high-mix, low-volume, small-to-medium enterprises and can easily be applied to most gear manufacturing operations.
The organizational hierarchy of the lean enterprise is comprised of executives, managers, engineers, supervisors and employees. Yet, when it comes to continuous improvement (CI) events, the literature on lean indicates an over-emphasis on the shop floor. These kaizens typically involve the plant manager, supervisors and employees who work in the department where the kaizen was done. Its as if engineers and managers are not contributing their share of the effort to improve the bottom line! Conventional wisdom says to let all CI work be considered and implemented only by the employees themselves. Otherwise, improvements will not be accepted or solutions will be implemented in half-hearted fashion at best. Should we avoid solving those sticky problems that have not been solved for years just because shop floor employees may not be able to solve them? Or should we expand our choice of who we put on these problem-solving teams so that experience blends with computer skills and analytical abilities?
In this section, I will describe the strategies that have guided the composition (team size, skills and experience of each
member, extent of crossfunctionality, etc.) of the continuous improvement teams that I have successfully utilized in the course of my job at Hoerbiger Corporation of America: Plan the composition of the team to suit the scope and complexity of the problem. Prioritize the problems based on impact on the bottom line and Figure 1Items Removed after a 5S Sorting Event. not who will be availShipping: Where our Continuous able to work on the team. Insist that the project must improve Improvement Efforts Began key performance indicators (KPI) such as The shipping department is the clossafety, quality, delivery, waste elimination, est to the customer, and its main objecetc. in the area where the team will work. tive is to maximize shipped orders every Leverage external resources; in parmonth. ticular, student interns from a reputed It was decided to assess how much of industrial engineering department or the current floor space in the shipping on-staff industrial engineers (or manudepartment was dead and therefore facturing engineers). could easily be reclaimed. First we did Utilize computer-aided analytics if the a walkthrough of the entire department problem merits it, such as the Six Sigma with the shipping team and pointed out statistical analysis software, Minitab. examples of areas that were VA (valueI will discuss the above guidelines in added), NNVA (necessary-but-not-valthe context of a series of inter-linked CI ue-added) and NVA (wasted). It was the projects that we are doing in the shipNVA areas that we focused on because ping department. they were occupied by junk. Naturally, the very first continuous improvement project was a simple housekeeping task
[www.geartechnology.com]
24
that lasted about two hours. We handed everybody a few red stickers and asked them to go around the department and affix their stickers to items that they were confident nobody had any use for. It turns out that our shipping department is essentially a job shop. It stands to reason because (1) Each of the five cells in our machine shop is a highmix low-volume job shop and (2) both focused factories in molding cold compression molding and hot compression molding are high-mix low-volume flow shops. The shipping department handles a mix of workflows since we serve global customers whose typical shipments involve a variety of parts. Different kits have different packaging requirements (carton size vs. wooden crate, labeling specific to the customer and country of destination, etc.). The routings that were processed in the shipping department were due to the following product mix: Packing Rings Piston and Rider Rings QRC Packing Rings Bushings and Cases GE Kits The department was advised to separate the product, person and information flows for each of these routings. The spreadsheet containing the Production Flow Analysis and Simplification Toolkit (PFAST) Input File was then sent to Pranav Joshi, a graduate student in the Department of Integrated Systems Engineering at The Ohio State University. The PFAST software was made available by The Ohio State
University for this project. We used the PFAST Analysis Report to generate five new alternative layouts for the shipping department. These layouts were designed based on guidelines such as a separate cell for each customer, a central shared IT Hub and other desired features. Presently, Clement Peng, from the IE department at Texas A&M University, plans to visit HCA-TX every Friday and completely immerse himself in the dayto-day operations of the shipping department. His goal is to develop a detailed blueprint for the final layout, including a budget and implementation timeline. Now that I am in industry, a realworld classroom where the true relevance and need for IE is widely evident, I am able to teach Peng how lean radically changes the standard approach to facility design that is taught in any contemporary IE textbook for facilities planning. Why? Because the footprint of each and every workstation, table, aisle, rack, container, etc. in the layout is potentially bloated with waste. Toyota either pioneered or raised the importance of concepts such as rightsizing, mobile machines, reconfigurable layouts, visual WIP management, combined operations, jidoka (automation with a human touch), parallel operations, and more. For example, Robert Lu (an employee in the shipping department) carefully places all the parts that are going to be shrink-wrapped on a GE skinboard (cardboard backing) on the packaging table. Next, he carefully picks up the GE skinboard, slowly turns around and places the kit on the table
of the shrink-wrap machine. Should not the two tabletops that he works on be a single sliding table that slides into and out of the shrink-wrap machine? At least that idea made us all pause and think for a moment during one of our weekly team meetings.
While the Sort phase of a full-fledged 5S program usually yields results, the real benefits to be gained from doing 5S are when the hidden evils such as ergonomic risks, inventory costs, inefficient flows of people and material are banished. Since inventory costs are visual and measurable, Team Shipping decided to take a systems approach to control the purchasing costs for the carton inventory. These cartons and wooden crates are used to ship our products all over the world, often to other Hoerbiger plants. That there appears to be excessive inventory of several SKUs (stock keeping units) of carton inventory is obvious. So we collected data on purchases of the different SKUs made from June 20, 2012, to November 7, 2012. This time series display of the data did not yield any insights. Instead, when we plotted the same data using the classical Pareto rule of 80-20, some valuable insights were gained. Here is where looking at color printouts of Excel graphs doesnt necessarily match the reality of the shipping department. It was pointed out to us that the high inventory of the GE Whiteboards was an unavoidable business situation because (1) we shipped that item
Figure 2b New layout being designed for the shipping department.
March/April 2013|GEAR TECHNOLOGY
25
feature
26
[www.geartechnology.com]
our suppliersGrainger. Inmer Ivan Guzman is one of their onsite reps, regularly replenishing inventories of shop supplies, office supplies, etc. One day I observed him using his iPhone to swipe bar codes for items stored in the cabinets in our lunch room. That was my first introduction to a VMI (vendor managed inventory) system that starts as a bar code swipe and ends as an order quantity uploaded to their ERP system. As we discussed our lean projects, he walked me over to one of his pet projectsan e-kanban system to manage supplies in our first aid cabinets on the shop floor. The numbers placed on the containers connect to the bar code for that item on the sheet stuck inside the glass door of the cabinet. If all goes well, that same system is what we will use to automate the weekly replenishment of the carton inventory held in the shipping department. Once that system is debugged we can implement the same data-driven computerized inventory control for: QRC packing boxes, GE skinboards, wooden cartons, bushings supermarket, powders and bar stock.
Material/Size
Consumption Footprint Volume Inventoryon during [square [cubic 11/6/2012 Oct.9Nov.6 inches] inches] 37 99 49 38 28 7 44 128 75 116 56 38 58 124 105 68 88 69 27 93 93 172 324 256 144 100 196 144 64 100 81 48 36 1296 1024 864 800 784 576 512 500 486 288 216
18X18X4 16X16X4 12X12X6 10X10X8 14X14X4 12X12X4 8X8X8 10X10X5 9X9X6 8X6X6 6X6X6
121 17 73 24 127
1 37 93 18 71
The downside of having quickly plucked all the low-hanging fruit so soon during our lean journey in the shipping department is that complex problems now need to be tackled. Figure 4 presents the potential for reducing the number of different cartons that we buy. If we could standardize on the sizes that we use, and reduce this number, that ought to reduce our purchasing and inventory carrying costs. For example, the carton sizes 866 and 666 differ by a cubic volume of only 72 cu. in. We studied the data on the usage of these two sizes during the period October 9November 6. If we decided to buy only the 866 size in the future, that would result in us shipping a total volume of (26656) cubic inches of air that would have to be filled up with crumpled paper or foam padding. How does that cost trade off against being able to buy 35 more cartons of the 866 carton size? This appears to be a technical problem that could be offered to an IE graduate student doing their MS thesis. Or, we could be pragmatic and listen to Pett who has already eliminated 4 SKUs as of the writing of this column. Figure 5 shows that the current state of how the on-hand inventory of the many different packing rings that we make and sell to our customers is stored in floormounted bins (Q-bins) and the space saver (vertical lift module). What do
March/April 2013|GEAR TECHNOLOGY
27
feature feature
DeliVeries
with materials in stock.
1-2 weeK
Like any small for-profit manufacturer, HCA-TX is not geared to solve any complex operational problem as if it were a three-year research project funded by the National Science Foundation. The shipping department, like any other cell or department, is a high-pressure work environment that is time-constrained and resource-constrained, but luckily, not patience-constrained. Team Shipping pursues just one daily goal receive the stuff coming in from one door and get it out the other door onto a truck that same day. If operational problems arise, they are solved using common sense, firefighting, thumb rules, resignation, brute force, overtime, teamwork, negotiations with customers and suppliers, sometimes even prayer. The nearest that we have by way of computer-aided optimization is spreadsheetbased solvers. And Team Shipping has done well to date. Despite the above operational constraints, I think that there is merit in HCA-TX establishing a universityindustry partnership with a couple of IE departments in the state. Once I read Lean Thinking, in 1999, I was convinced that lean is the correct industrial engineering that we never taught to our students in any IE department. In a perfect world, a group of practice-oriented IE faculty would first work in industry to get sufficient work experience.
mcinnesrolledrings.com
Figure 5 Current storage of packing rings in the Q-rings and space saver.
28
[www.geartechnology.com]
Then they would seek federal funding to establish a national industry-university research center in partnership with the NIST network of Manufacturing Extension Partnerships (MEP). And what would they do? Produce a slew of much-needed heuristic optimization software tools that would allow industrial engineers in the field to modernize and extend lean beyond its pencil-andpaper problem-solving tools.
Hoerbiger Corporation of America (www.hoerbiger.com). In his current job he has two responsibilities: (1) To undertake continuous improvement projects in partnership with employees as well as provide them OJT training relevant to those projects and (2) To facilitate the implementation of job shop lean in HCAs U.S. plants. Previously, he was an Associate Professor in the Department of Integrated Systems Engineering at The Ohio State University (OSU). There his research focused on the development of new IE methods to adapt and scale lean for use by high-mix, low-volume SMEs (small and medium enterprises). His research group created PFAST (production flow analysis and simplification toolkit), which is a software program for material flow analysis and facility layout to implement Job Shop Lean. At OSU, he received the Outstanding Faculty Award for excellence in teaching from the graduating classes of 2002, 2003, 2004, 2005, 2006 and 2009. In 2002, he received the Charles E. Mac Quigg Student Award for Outstanding Teaching from the College Of Engineering. He is a member of IIE.
Quality/Inspection
Many companies take for granted the fact that the shipping department is the last quality check before the product goes out the door, says Bipin Doshi, president, Schafer Gear Works, Inc. Its essential for the shipping team and the production team to be on the same page. If the department takes a proactive approach and is very conscious of everything that is happening, they can make sure they dont ship product with any problems. Communication between departments is crucial as well as a holistic approach to lean manufacturing that involves everyone from the ground up. Our greatest challenge is to improve quality and delivery time while also reducing costs, Doshi adds. Continuous improvement (CI) initiatives have helped open communication lines between departments, so the shipping personnel, for example, know whats going in and out on a weekly and monthly basis. Its nice to have an extra set of eyes before your product goes out the door. We consider our shipping department sort of like the last line of defense before our product reaches the customer.
Carton Count
Maintaining the proper amount of shipping material, for example, used to be a real problem, Werschky says. If youre packaging a special order and its out of the ordinary, it may require a certain box size you typically dont carry. Its time consuming to chase around looking for the best material to ship the product. We try to carry the right amount of materials for our current requirements. This prevents us from not having enough shipping containers and also prevents us from carrying too much. Schafer Gear Works and Delta Research Corporation boast rather efficient shipping departments and lean manufacturing has most certainly played a key role. In 2009, both companies appeared in a lean manufacturing article (Steadfast and Streamlined, Gear Technology, August 2009) that discussed the benefits of lean during the economic downturn. These companies have paid close attention to the lasting benefits of continuous improvements across the shop floor. These improvements continue to pay off today.
March/April 2013|GEAR TECHNOLOGY
Maximizing Space
We essentially grew out of the building we were in previously, says Tony Werschky, sales/partner at Delta Research Corporation. We moved into a new building and created a flexible gear cell that includes part cleaning, deburring, packaging and shipping. This essentially has streamlined our production process and helped us with our throughput. Whiteboards for communication improvements keep personnel up to date on everything coming in and going out of the department. Because the company specializes in both aero-
Committing to Lean
29
feature
The Applied Process family of companies specializes in the austempering heat treatment process of steels and irons. Austempered Ductile Iron, ADI, constitutes the majority of our work, and the remainder of our heat treating work is split between austempered steel, carbo-austempered steel, austempered gray iron, carbidic austempered ductile iron, and marquenched steel, says Justin Lefevre, regional sales engineer at Applied Process. ADI offers gear manufacturers an opportunity to gain the manufacturing ease of ductile iron with properties comparable to some of the common steel gear heat treatments at a low product cost. Austempered and carbo-austem-
Applied Process and AFC-Holcroft joined together to produce a Monster Parts Universal Batch Quench-Austemper (UBQA) furnace (courtesy of Applied Process).
30
partnerships is a key part of this process. We engage in evaluation of the existing material, manufacturing methods, and application stresses of parts with designers. In doing so, often the optimum choice of material and manufacturing method is apparent, which sometimes leads to austempering business, Lefevre says. Applied Process launched AP Monster Parts Division in 2012 in Oshkosh, Wisconsin with what is believed to be the largest universal batch quench austempering furnace in the world and added two furnaces in the Livonia, Michigan plant. In January 2013, the company hosted AP University for the first time to give customers an opportunity to learn about ductile iron design, foundry practices and austempering in general. It was so successful that we have already planned another AP University for May of 2013. This, of course, is in addition to the 25-50 onsite presentations that we do for multiple customers every year.
As for overall business, it softened during the last quarter of 2012 but Lefevre expects 2013-2014 to show improvement especially in the larger gears for their new furnace. We already have several projects underway that involve conversions to austempered ductile iron gears in the heavy industrial market; we cannot say much more than that about the projects. Our efforts in the near future in relation to gears are to focus on conversion opportunities in agriculture, mill gears, and automotive applications, Lefevre says. Factors that will determine the future success of Applied Process include governmental policies and regulations that impede the growth of the economy, the companys ability to get austempering, specifically ADI (austempered ductile iron), as an accepted heat treatment/ material in the gear-making/using community and the ability to produce property data that end users of gears require in order to specify austempering/ADI as a suitable material.
Natural gas and raw mineral prices impact our cost model; however continuous improvements to our equipment help to mitigate these effects. The long term outlook for natural gas, electricity, and alloy costs are all positive for the heat treating industry. In other words, lower or stable prices will lead to stable prices for our customers, Lefevre adds.
L ow - pre ssu re v a c uu m c ar bu r i z ing (LPVC) and vacuum gas nitriding (VGN) are the two main areas in which Solar serves the gear market. The advantages include clean, bright parts with limited to no distortion, says Tim Steber, regional sales manager. The company also boasts an R&D department with metallurgist, scientists and engi-
31
feature
Don Jordan, vice president of R&D/ corporate metallurgist, says that growth in the aerospace market has been significant for Solar, particularly with new high alloy grades developed specifically for LPVC including Ferrium C61 and C64, Pyrowear 675 and CSS-42L. Our company collaborates with all prime rotorcraft (helicopter) aerospace companies and their suppliers, Jordan says. Jordan believes that the most significant products and technologies in the future will be continued developments and advancements in LPVC and highpressure gas quenching in vacuum heat t r e at p r o c e s s i n g of traditionally oil quenched alloys (e.g. 4140). Laser induction hardening will also play a significant role in multifunctional machining operations. Trevor Jones, prinSolar Atmospheres is comprised of more than 40 vacuum furnaces backed by NADCAP Accreditations and certified by ISO 9001/AS9100 cipal engineer at
(courtesy of Solar).
neers on staff for consultation and oversight of work. Solars Souderton plant recently received a Nadcap accreditation in carburizing, allowing it to better serve the aerospace market. This accreditation joins Solars other Nadcap approvals for heat treating, brazing and fluorescent penetrant inspection. Additionally, earlier this year the company became an approved supplier for General Electric Aviation (GEA), UTC Aerospace Systems (UTAS) and Moog Corporation.
TRIUMPH
DISASTER
Precision Technologies Group (PTG) is a world leader in milling and grinding technologies, special purpose machine tools and ultra precision components for HVAC, aerospace, motor racing, medical, marine, steel, oil and gas. For absolute precision, choose PTG Holroyd Precision.
Holroyd Precision Ltd t +44 (0)1706 526590 f +44 (0)1706 353350 e info@holroyd.com www.holroyd.com
32
[www.geartechnology.com]
A progressive gear manufacturer understands it needs to go above and beyond traditional expectations. Todays customers demand and deserve the latest technology, a wide range of capabilities and an unrelenting commitment to prompt and effective customer service. When it comes to exceeding expectations, Schafer Gear is truly light years ahead. Our investment in the latest production equipment assures that we can provide gears for many industrial applications including transportation, medical, mining, gas and energy, agricultural equipment and many specialty applications. And every gear we make comes with one thing standard the willingness to go to the ends of the earth to serve our customers well.
feature
Stack Metallurgical Services began with a couple of atmosphere furnaces and has evolved into a versatile provider of heat treating services. Vacuum carburizing provides improved case depth uniformity over the tooth profile, says Nels Plough, president and general manager at Stack Metallurgical Services, Inc. Root to flank ratios is as much as 90 percent versus 65 percent for conventional gas carburizing. Intergranular oxidation is also eliminated in vacuum carburizing. Fixture and furnace designs offer reduced distortion by providing uniform heat removal from the part. Much like other heat treat companies, software is becoming a key element to industry requirements. Computerized control of every aspect of the furnace is critical. Precise, repeatable processing is vital to give our customers the high quality parts their industry requires. In addition, a charting program records all of the important parameters of a run for verification. While the physics of heat treating havent changed, our ability to precisely and repetitively control the process has been greatly enhanced by software advances, Plough says. Stack has key customers in the gear industry, according to Plough. When we work in close contact with them, our ability to meet their specifications is greatly improved. The more each of us know about the requirements and limitations of the products, the more improvements can be made. Both energy costs and labor are two significant challenges at Stack. As the economy continues to improve, the energy resources will become more expensive and have a large effect on profitability. Energy costs must be controlled. Renewable energy initiatives are going to drive these costs higher, Plough adds. Despite these challenges, business continues to grow. The strength of this business is dependent on the overall economy, but also on our ability to grow and adapt to the increasing quality & processing requirements, Plough says.
Brad Footes captive heat treat facility in Pittsburgh, Pennsylvania is one of the largest in North America (courtesy of Brad Foote Gear Works).
controllers for each individual furnace and individual monitors. All of the nine furnaces were completely rebuilt and new recuperating burners were installed in each. Brad Foote began primarily as an in-house heat treating facility but expanded to commercial work because of the companys wellknown capabilities and capacity. We helped a competitor on a very large part that they couldnt handle in their plant. Because of our quick turnaround, pricing, in-house testing lab and quality, they sent us more work, Baker says.
ing. While Baker wont divulge any secrets to the companys success in this market, he does have an idea why many captive heat treaters fail when they attempt to get commercial work. The trick is to stay within your capabilities and not overpromise anything. We know gearing and have been carburizing gearing for many years. Our workforce experience averages more than 20 years of heat treat experience.
34
[www.geartechnology.com]
lished (collection of all quality data on one computer). The companys introduction of its SynchroTherm is evidence that ALDHolcroft believes that the in-line, insynch approach will have significant market appeal. Our unique approach to high volume processing has become the mainstay in the automotive gear market. The extremely high up-time of our systems in conjunction with an outstanding
service network has ultimately been a winning combination, Heuer adds. The company is having great success in Europe, Mexico, Russia and South Korea and continuing to focus on China, India, Southeast Asia and the United States for the future. ALD has found its fair share of challenges when it comes to energy pricing and raw materials. Prices of raw materials have a direct effect on our equipment pricing. Further, our customer base has
CHALLENGE:
Using a versatile, highly accurate cutter to simplify processes and minimize costs
All new processes are developed with the help of simulation software according to Dr. Volker Heuer (courtesy of ALD-Vacuum Technologies).
35
feature
reluctance to improve alloying factors (because of cost) in materials in order to take advantage of higher temperature processing. The math proves the process is worth the extra cost, but quite often legacy parts and processes dictate, Heuer adds.
Ipsen is known in the industry for its wide range of equipment, advanced technology and strong service and support in Asia, North America and Europe. The companys atmosphere equipment includes pusher, batch and rotary hearth furnaces while its vacuum technology includes single chamber with AvaC + high pressure gas quench to 15 bar, 2 chamber furnace oil quench. Ipsens mission is to be a dependable, long-term partner, recognized for the quality of its products and reliability of its commitments. This means collaborating with our customers to find out what they need and want out of their thermal processing equipment, allowing us to provide the best equipment, which in turn allows them to be successful, says Geoffrey Somary, president and CEO of Ipsen USA. Aftermarket Support and Service is one of the most important aspects of Ipsens business. When you buy heat treat equipment from Ipsen you buy equipment backed by 65-year experience, and we dont stop at delivering new equipment. We are here to help you maintain and care for your equipment in order to help you minimize downtown and keep your equipment running for years to come. Our Engineered Components group helps your equipment stay up-to-date with retrofits and upgrades. We have some furnaces out there that have been running for 60+ years, so its important to keep these furnaces working for our customers, including new hot zones, upgraded controls, adding capabilities and much more, Somary says. Today, the company is focusing on improving the customer experience. With our Titan line of furnaces, we already offer what we call The Titan
them, we will get run over. So in 2012, we decided to start the Ipsen Corporate Academy. This offering helps us to find, attract, train and retain the best talent available. In this three-month program, new recruits participate in a rotational training program that helps them take the knowledge theyve learned in school/ previous jobs and turn it into experience what we call books to business. It is our hope that this will allow them to build a strong foundation for success. The Ipsen Corporate Academy benefits not only the new hires, but also the company as a whole. We make better use of everyones time and resources through this streamlined approach, making this a smart investment. We reinforce our corporate culture by creating an inclusive, welcoming climate all while creating a more cohesive, productive and collaborative team of employees, Somary says. The future health of the organization will bring growth, challenge and opportunity, according to Somary. We are committed to what we call evolutionary innovation, as well as revolutionary innovation. The idea is that we must contribute to the success of our customers in order to achieve success as a company by bridging the gap between our customers dreams and the technology available to make those dreams reality. This is the concept behind our, You dream it, we build it, philosophy. Our mission also reinforces this idea Be a dependable, long-term partner, recognized for the quality of our products and reliability of our commitments.
36
[www.geartechnology.com]
Manufacturing thermal processing solutions for over 50 years. Extensive range of standard products for stand-alone or total systems. Engineered solutions to meet specific process or configuration needs. Reliable products focused on ease of operation and maintenance. Commitment is to satisfy companies by providing Performance. Proven Heat Processing Equipment Incorporating the Latest Product Enhancements. Contact BeaverMatic to find out more about how we can help your company succeed.
1715 Northrock Court | Rockford, IL 61103 | Tel: 815.963.0005 | Fax: 815.963.5673 www.beavermatic.com | sales@beavermatic.com
feature
tics, of course, but the industrys cut of the pie becomes increasingly significant with each new year. Backing that up in a recent radio broadcast, available online at the SPI site, is Bryan Osborne, vice presidentof sales and marketing for business of supplying U.S. automakers injection molder/manufacturer Venture with engineered-plastic gears and other Plastics, Inc. (Newton Falls, OH), stating critical car components are not among that About 50 percent of a car is plastics them. today, and that demand for more fuelIndeed, the U.S. automotive industry efficient vehicles is behind the increase. has been in rebound mode since 2010, That includes under the engine, manaccording to the Society of the Plastics ifolds, fuel rails, (etc.). In d u s t r y ( S P I ) And that claim is certainly sup(plasticsinported by the fact that the automodustr y.org ). tive industry is the second-largest And since userafter packagingof U.S. plastic products. And finally, these 2011 post-recession numbers from the SPI business blog, In the Hopper, under the headline, U.S. Automakers Upbeat 2011 Is Sweet Music for Plastics Industry: 2012 looks to be a good year for U.S. automakers, domestic and foreign brands, as well as for their creative partner suppliers in the plastics industry. For what they have each been through in the last few rough years, both automakers and plastics suppliers have more than earned Under-the-hood automotive gears from Kleiss Gears some good times. (all photos courtesy Kleiss Gears). More (inclusive) plastifacts from 2011, according to Stout, Risius and SPI: The plastics industry is the third largRoss (SSR) ( srr.com ), an industrialest manufacturing industry in the focused financial adviser and consulUnited States tancy, North American automotive The U.S. plastics industry employs production totaled 15.4 million units more than 885 thousand in 2012up from 13.1 million units The U.S. plastics industry creates more in 2011and is expected to increase than $380 billion in annual shipments further to approximately 15.9 million When suppliers to the plastics indusunits in 2013. Not all of that is in plastry are considered, there are 1.4 mil-
lion workers and total shipments grow to $465 billion There are more than 16,200 plastics facilities in the United States The U.S. plastics industry had a $16.3 billion trade surplus in 2011 The plastics industry has a presence in every state From 1980 to 2011, U.S. plastics industry shipments have grown at a 0.1 percent annual rate But enough numbers crunching; lets talk to some of the folks and companies behind the numbers the engineered materials suppliers and the component manufacturers. Rod Kleiss is the president of Kleiss Gears (kleissgears.com) in Grantsburg, WI. This story having an automotive focus, we cut right to the metal vs. plastic under-the-hood chase. (And lets face it: its all about metal vs. plastic, is it not?) Plastic has already made great inroads regarding engine gears and parts for consumer-type vehicles; but we asked Kleiss just how far along are things in qualifying various gears and power components for industrial-size engines? (To be clear, industrial in this context means off-highway, heavy equipment.) The answer lies in both materials engineering and sophisticated design. (Partnering) with Victrex (a leading materials supplier to the engineered resins/plastics industry), we have been molding and testing plastic gears in engines for a few years now with some very good success. We have found some unique design approaches that work quite well in replacing their metal counterparts. This includes varying the pressure angle to fit the specific requirements and applying a minor helix to the gears just to limit the potential for tooth slap. We have just begun our first production order for a molded gear replace[www.geartechnology.com]
38
ment of a ground gear in road building equipment. We are not at liberty right now to reveal the customer or application but I hope to get permission within the next few weeks. And for John Winzeler (winzelergear. com), owner/operator of Chicago-based Winzeler Gear, and playing it a bit closer to the vest, With all gearing applications, appropriate testing and development are critical. Today many small engines have molded plastic cam gears. Of course there are limits to temperature and load capacity. By all accounts polymer is here to stay, but in what types of automotive applications? Where can plastic be counted upon to match or prevail in performance? In quite a few places, according to Kleiss. But hes willing to share (with metal). Plastic is better for vibrating loads, such as counterbalance shaft rotation or vibrating equipment applications, says Kleiss. Also, in applications where normal loads are not excessive but occasional, short-term spikes must be anticipated. In general I think that plastic will find its place at the front end of transmissions where higher speeds and lower torques are occurring. They will reduce rotating mass and the corresponding noise and leave the high loads to the steel gears. One claim of plastic gearing is beyond disputeless noise and vibration. And why is that? Sound levels are a function of speed and accuracy for all types of gearing,
sharing may tend to dampen the physical oscillation of the gears, while the hard metal gears translate every small motion into rotation. That is just a speculation or theory though. Among the most critical plastic components now and for some time, in fact being used in vehicles are plastic bearings. For the best source of updated information on that score we went to two major, international materials suppliers with diverse portfoliosDSM, headquartered in The Netherlands (dsm. com) and Ticona Engineering Polymers, a Celanese company based in Dallas, Texas (celanese.com/ticona/ticona.aspx). Plastic bearings (bearing cages) are more mature (accepted) in the automotive market than gears and actuators, points out Pascal Feijts, DSM applications development manager/global research and technology. For plastic gears the new trends in downsizing and turbocharging drive the need for more electrical actuators with geartrains. Also, metal replacement for in-engine gears to improve NVH or improve emission and fuel levels is more and more upcoming. Ticonas David Sheridan, senior design engineer, agrees that Yes, engineering thermoplastics are proven sliding materials in precision engineering applications such as thrust bearings, sleeve
About 50 percent of a car is plastics today; that includes under the engine, manifolds, fuel rails, (etc.).
Bryan Osborne, VP of sales & marketing, Venture Plastics, Inc. (Source: SPI).
Winzeler explains. Plastic materials generally are softer than metals and absorb energy better. As Kleiss puts it, its kind of a mystery. One of the basic reasons is that they (plastic gears) just dont carry sound as well, and their natural frequency is much lower. I think you can hear the effect of that directly in (sound testing). (It may be that) under a vibrating load, the plastic teeth bend a little and this load-
bearings and bushings. Although they dont have the high-load-bearing capacity of metal, plastic bearings offer lower cost; lower weight; ability to run dry; inherent low friction and noise; maintenance-free operation; chemical resistance and broad design flexibility. He also touts one of his companys patented products Hostaform C 9021 AWfor its low-wear, friction, and squeak system, as a material of choice
for high-quality molded engineering parts subject to high stress, including gears, bearings and other sliding elements used in precision engineering. And what about gearboxes? Its a given that their engineering complexity is matched only by their need for robustly made components to operate in miserable conditions. It all comes down to loads on the gears (torque rating) in combination with the durability requirements to see how far plastics can go, Feijts allows. Reinforced plastics are more likely (specified and used) here due to high strengths needed, but they suffer on wear rate compared to unreinforced plastics. For hisand Ticonaspart, and on behalf of reinforced fiber products that Feijts alluded to, Sheridan points to An innovative transmission from Hi-Lex America Inc. (that) reliably and quietly opens and closes automotive lift gates thanks to high-precision shafts and gears injection-molded with Celcon POM and Celstran long-fiber-reinforced thermoplastics (LFRT). The two-stage reduction transmission uses precision steel ball bearings mounted on plastic shafts and 2.5-inch-diameter plastic gears to achieve the desired reduction between the electric motor and a flexible torsional cable. The first-stage gear and shaft and second-stage output plastic gear are injection molded from Celcon POM M90 and Celcon GC25T, respectively. The second-stage output shaft is injection molded from Celstran PA 66-GF50-02. The
39
feature
Hi-Lex transmission with plastic gears reduces cost, weight and especially, noise. Yet regarding worm gears, common in gearbox designs, work remains to be done for the plastics industry. I understand that well-lubricated steel worm drives can be really efficient, much greater than 95 percent. We are not there with plastics, Kleiss admits. One rule-of-thumb is to estimate efficiency as .95 for a reduction ratio of 3.5:1; therefore, a 40:1 worm drive might be expected to achieve 85 percent efficiency in the gear mesh. You really have to look at the sliding friction of the teeth on each other in a plastic worm to get a good idea of efficiency. On the other hand, Winzeler believes that Plastic worms may provide lower frictionthus higher efficiencydue to the lubricity of the plastic material compared to metals. We recommend all applications be, at a minimum, initially lubricated with grease. Staying with our components suppliers, we queried Kleiss on microgears, a
The state-of-the-art has advanced to where plastic gears are now in drives of up to three-quarters horsepower; future applications may take them higher.
David Sheridan, Ticona
nascent-yet-promising technology with great promise for plastic. Micro gears (>200 DP) are still an infant science in my book, Kleiss concedes. In larger gears, grinding accuracy can produce more exact geometry than molding, but as the gears keep getting smaller, that advantage begins to disappear. But along with that disaping another cavity for the molded-gear manufacturer. We can put a spur gear onto the end of a worm with no problem and add features on to that spur, if desired. That would be quite difficult for the metal gear manufacturer. Current uses and applications-inwaiting for plastic microgears include, says Kleiss, small medical pumps with t h row - aw ay ge ar s t h at could never be considered as a cost-effective option in steel, adding that All the new microgear applications will be served better by plastics. The challenge will be to actually build the little transmissions. Molding the gears might be the easiest part of the project. Jumping back to the materials end of things, one wonders is the glass half-full
or half-empty regarding the heights to which plastic gears and related components (bearings, actuators, etc.) might ascend in the automotive arena. Depending on the system or application, I have seen durability requirements for motor management actuators going up to 30, 40 million load cycles, with quite challenging torque ratings, says DSMs Feijts. Other in-engine applications are fit-and-forget, so durability levels can go up to 1, 1.3 billion load cycles! We at DSM are continuously looking into possible ways to improve our materials. Both strength and durability (which can be differently defined depending on which application we are talking about) are important subjects that we are looking at both on the polymer matrix and/or reinforcement/filling side. For Ticonas Sheridan, it is a matter of The higher the performance requirements for a drive, the more complicated the up-front design effort is required to make plastic gears work. The state-ofthe-art has advanced to where plastic gears are now in drives of up to threequarters horsepower; future applications may take them higher. Horsepower limits for plastic gears vary with the polymer, depending upon the mechanical properties that change with temperature. Temperature control, therefore, is critical for plastic gear load capacity. Lubricantsboth internal and externalthat reduce frictional heating or dissipate heat will increase plastic gear load capacity. Furthermore, long-glassfiber-reinforced plastics will allow for larger tooth and wall thicknesses of a larger-size plastic gear that will withstand higher loading. To some analogous degree, plastic gearing is as reliant on the art of injection molding and its continued research and development as is its more mature
[www.geartechnology.com]
40
metal counterparts forging and casting. Is there a tilting point? Injection-molded plastic gears have come a long way, says Sheridan. Historically, they were limited to very low-power transmissions such as clocks, printers and lawn sprinklers. Todays stronger, more consistent engineering polymers, and better control of the molding process, now make it possible to produce larger, more precise gears that are compatible with higher horsepower. In addition, Gear analysis software can now optimize plastic gear designs based on temperature, moisture pick-up and other environmental factors. The unrealized potential of plastic gearing is becoming more apparent to the industry. Testing of plastic gears specifically to characterize gear resins in different service environments has begun. The new data will allow design engineers to more accurately predict gear performance. Better predictions mean faster, shorter design cycles, since the development phase may be approached with greater confidence. Perhaps; DSMs Feijts believes plastic continues to suffer second-cousin status vs. metal in the perception of some. And it has nothing to do with process. No, current limitations are more depending on the markets perception of using plastic gears instead of metal
ones. The market is opening up due to more stringent national and international emission and fuel consumption legislation, so for the time being the injection molding technologies available (which are also evolving continuously) are sufficient enough. Proper lubrication and lube maintenance can be as critical to the working order of a plastic-fashioned gearset as with metal. Difference being, however, and its a big one, there are reams more literature on metal gear and bearing/
lubrication issues than exists for plastic. For the relative new kid on the block, it can be more trial-and-error as the application opportunitiesand their challengescontinue to multiply. We work very closely with oil and grease manufacturers, but are also working on improving the dry lubricants (types and composition) that we use for our engineering plastics, says Feijts. New, emerging applications also introduce new insights in lubrication requirements, so this needs constant develop-
more than 1,000 experts from the field of transmission development more than 80 expert lectures more than 50 exhibitors simultaneous translation
accompanying VDI conferences: Transmission in commercial vehicles Control solutions for transmissions
www.transmission-congress.eu
Gold Sponsors:
Register now!
Organised by VDI Wissensforum GmbH | www.transmission-congress.eu | Phone +49 211 6214-201 | Fax +49 211 6214-154
41
feature
ment and research into the fundamentals of wear and friction between plasticwith itselfor other materials. The way Sheridan explains it, its even trickierdetails, details, details. Andless is more. A fundamental misconception in plastic gear design is thatwhatever the resin Its just plastic. The choice of a gear resin demands careful study. Inexpensive, commodity resins generally lack the fatigue life, temperature resistance, lubricant resistance and dimensional stability required for quality plastic gears in all but the most primitive applications. However, many of todays engineering resins provide the necessary performance for working gear trains. They also have the consistent melt viscosity, additive concentrations and other qualities essential to consistent, accurate molding. Generally, it is easier to mold highquality gears with resin containing minimal additives than with highly filled blends. The specifier should call for only as much glass or mineral filler or lubricant additives as are actually needed. If external lubrication is required, the drive designer, resin supplier and lubricant supplier should work together to select an appropriate lubrication system. A discussion of plastic and automotive cannot ignore the perhaps not yet of elephant stature, so lets go with creaturein the room: the powder metal (PM) industry. How does its performance match up with plastic? A fair question, or an apples-and-oranges thing? Judging from the following replies, sounds like PM and plastics have a peaceful coexistence, with limited overlap. Think of PM as the plastic familys brawny-not-brainy counterpart. Powder metal serves an important function as a low-cost, high-strength mate to plastics at the input or output
42
[www.geartechnology.com]
www.IpsenUSA.com/ATLAS
Time is money whether youre producing bevel gearsets by the thousands or in lots of just one. New Gleason machine, tooling, software and inspection technologies save you precious time at every step of the production process and close the loop on quality with our complete bevel gear production capability. Why wait? Start saving precious time, and money, today. Visit: www.gleason.com/bevel.
280CX:
35% faster cutting of bevel gears up to 280 mm in diameter. A new generation of 5-axis machining centers; up to 8 times faster production of larger bevel gears.
GMS Series:
25%-45% faster complete inspection of bevel and cylindrical gears and gear tools up to 3,000 mm in diameter.
IN DIAmETER
Workholding Global Services
www.gleason.com sales@gleason.com
Visit www.forestcitygear.com.
11715 Main Street, Roscoe, IL 61073 815-623-2168
CareFusion and the EnVe name are 2013 CareFusion Corporation; Used with permission.
feature
was made possible by nudging the gear with the probe of a scanning, tunneling microscope. According to the Guinness Book of World Records, it is the smallest working gear in the world. In an attempt to locate the LARGEST gear in the Guinness Book of World Records, this author fell incredibly short. Theres no mention of, for example, some of Rexnord/Falks mining girth gears or the single-helical SAG mill girth gear from David Brown (England)
The worlds largest gear is kind of a sore spot for some manufacturing organizations. It can become a rather contentious subject particularly if you get engineers from competing firms discussing the topic. This was brought up at a recent SME meeting, says William Rhody, marketing manager, mill products at Rexnord. Some companies will downplay the capabilities of their competitors or assume that they have the biggest or the best equipment without doing the research. Theres a lot of misinformation out there so its nice to set the record straight.
Hofmann Engineering recently shipped a gear boasting an outside diameter of 13.2 meters and weighing 73.5 tonnes.
March/April 2013|GEAR TECHNOLOGY
47
feature
From a manu f a c tu r i ng st and point, Rhody believes a debate about the worlds largest gear would have to include both the physical size as well as the power. I can see how several companies could make a case depending on the way you look at it. In our research, companies in the discussion for worlds largest gear would include Rexnord/Falk (United States), P. van der Wegen Gears (The Netherlands), Hofmann Engineering (Australia), CMD/Ferry Capitain (France), FL S m i dt h ( D e n m a r k ) a n d N K M Z (Ukraine). ( Ed.s Note: These were the companies that responded to inquiries on the subject. If were missing a company that should be in the discussion, please contact us at publisher@geartechnology. com). Rhodys assertion that various companies debate and discuss their manufacturing capabilities and flex their BIG GEAR muscles is absolutely true. There have been arguments in the past, press releases sent out claiming world records and even trade organizations and magazines attempting to crown a king.
Ferry Capitains recently commissioned VBCM16 is capable of turning and cutting gears up to 16 meters in diameter with 1,200 mm face width and 350 tons on the table.
48
[www.geartechnology.com]
mills and construction applications. Mining is the biggest market for our operation, but we have manufactured a lot of big gears for the cement and fertilizing industries as well, says Fritz. Weve also made slew gears for satellite dishes. Many of these gears are large enough to comfortably sit an entire manufacturing staff (See photo on page 47).
Hofmann Engineering shipped a forged steel mill gear recently boasting an outside diameter of 13.2 meters and weighing 73.5 tonnes. It will transmit 17,000 kW when driven by two 9-tonne pinions. The gear is being utilized in an undisclosed copper mine in China. This gear is just 1 mm bigger than the gear that we manufactured five years ago for BHP Billiton (an Australian mining and petroleum company), says Fritz. We are also quoting on different designs at the moment with dual pinion mills up to 22,000 kW and dual girth gear mills up to 34,000 kW. We currently have an order for a mine in North
America for a ball mill gear with a with a 9,000 kW single pinion drive. While Fritz doesnt know what gear sizes the competition is supplying to the mining market, he does note that Hofmann boasts one of the biggest gear cutters in the world. Our biggest machine is a 15,000 mm machine, followed by 14,000 mm, followed by an 11,000 mm. These machines are all hobbing/form cutting machines, but we also have three MAAG machines. But can Hofmann actually claim the title of worlds largest gear? Not so fast, according to the competition. Rexnord/Falk boasts a 13.5 meter OD SAG mill gear set at the Los Bronces Copper Mine. We also have two Detour Lake SAG mill gear sets, at 13.4 meters, Rhody says. Additionally, there are five others with diameters between 13 and 13.2 meters. In terms of mill power, two of these have a total mill power of 24,138 hp. There are three other ball mill gear sets, with diameters less than 13.1 that have a mill power of 23,132 hp. Hans van der Wee, of P. van der Wegen Gears b.v., says the compa-
ny once delivered a 14 meter gear. At the moment we have several very big gears on order (to be delivered at the end of this year and the beginning of next year) with an external diameter of a little below 14 meters. These gears are all for the minerals industry. In fact, P. van der Wegen is currently working on different methods for the manufacture and production of large gears. At the moment our maximum diameter capability is 16.5 meters, says van der Wee. We are currently expanding our capacity and capabilities so that we will be able to produce gears (using the generating method and not, as many others do, the single-indexing method) up to a maximum diameter of 30 meters, though we have not yet encountered these size gears. Ferry Capitain has already produced a 13.6 meter diameter girth gear, according to Ferry, and the company is currently producing a 16 meter diameter girth gear. While Ursula Mian, head of marketing and communication at FLSmidth MAAG Gear states that the company is
49
feature
limited to about 11.2 meters, she confirms that P. van der Wegen Gears, Ferry Capitain and NKMZ are in the discussion. We know that van der Wegen can today produce up to 14 meters and they are investing soon in a new machining center to produce even larger gears. Novokramatorsky Mashinostritelny Zavod (NKMZ) in Kramatorsk, Ukraine produces up to 15 meters on a new multi-machining center and Ferry Capitain can surely produce 14 meters. So, Ferry Capitain at 16 meters takes the crown, right? Not quite.
The worlds biggest gear saga played out once in back issues of this very magazine when one Peter Mayo, of Toronto, N.S.W., Australia discussed a 92 meter diameter red mud tailings thickener in Western Australia. The question was raised whether or not a thickener rack or dragline rack should be even considered gears in the first place or should the name be reserved for gears that rotate (The Bridges of Cook County
William Rhody, marketing manager, mill products at Rexnord, believes both physical size and power need to be included in the World's Biggest Gear debate.
50
[www.geartechnology.com]
is a cog railroad, since the rail is a rack, which is a segment of a gear of infinite diameter. Perhaps this argument would best be resolved by getting all the companies together in a room with a potential BIG GEAR customer and let the chips fall where they may (pun intended). For all intents and purposes, its difficult to argue which gear is the biggest or most powerful because its essentially going to come down to satisfying a customers request. If a gear customer has a need for a 35 meter gear, these companies will find a way to manufacture one. Its what they do. As the technology improves, companies will be capable of making larger and larger gears and its going to be impressive to see the results, Rhody adds. Its fun to imagine how big they might actually get. In the meantime, talking about it only leads to anger and/or resentment. Someone that sees a press release claim-
ing Worlds Largest immediately scoffs because the record wont stand for very long. In fact, the average Photoshop aficionado could create the worlds largest gear with a few mouse clicks and some minor photo manipulation. Until Guinness sends a representative down to verify one of these mining gears with a notepad and a serious tape measure, all bets are off.
No one will be named manufacturer of the Worlds Biggest Gear in this article. Instead, its better to just stand back and admire the handy work of these massive components. If youre hell bent on naming a champion, we suggest a bit of restraint. By the time youve crowned the manufacturer of the worlds largest gear, were confident that some other company will be shipping a bigger one. Good for the big gear business, ultimately bad for the bragging rights.
David Brown Phone: +(44) 1484 817378 uk@davidbrown.com www.davidbrown.com Ferry Capitain Phone: +(33) 3 2594 0424 ferryby@ferrycapitain.fr www.ferrycapitain.com FLSmidth Phone: +(45) 36 18 10 00 info@flsmidth.com www.flsmidth.com Hofmann Engineering Phone: +(61) 8 9279 5522 Mail.hofmann@hofmannengineering.com www.hofmannengineering.com NKMZ Phone: +(38) 06264 3 70 80 ztm@nkmz.donetsk.us www.nkmz.com P. van der Wegen Gears BV Phone: +(31) 13 5362 000 purchase@vanderwegen.com www.vanderwegen.com Rexnord Corporation Phone: (414) 643-3000 RexnordCS(yourstate)@rexnord.com www.rexnord.com
All Are Right Here All The the Gear Cutting Tools You Will Ever Need are
DTR is one of the worlds largest producers.
DTR. Your best choice for high quality gear cutting tools.
DTR is a world class supplier of the finest high performance long-life gear manufacturing tools, for small and large gear cutting applications. Established in 1976, we are one of the worlds largest producers of cutting tools, shipping to over 20 countries. DTR offers a full line of gear cutting tools including: Hobs Chamfering and Deburring Tools Carbide Hobs Broaches Shaper Cutters Master Gears Milling Cutters We can produce virtually any tool you need for auto, aerospace, wind, mining, construction and other industrial gears. Every tool is precision-made utilizing high speed steel, premium powder metal or carbide and the latest in coatings, to achieve superior cutting and long life. DTR uses top of the line equipment including Reischauer CNC grinders and Klingelnberg CNC sharpeners and inspection equipment. Learn more about our outstanding quality tools at www.dragon.co.kr. Call us at 847-375-8892 for your local sales representative or Email alex@dragon.co.kr for a quotation.
U.S. Office Location (Chicago) Email inquiries to: alex@dragon.co.kr 2400 E. Devon Ave., Suite 210, Des Plaines, IL 60018 PHONE: 847-375-8892 Fax: 847-699-1022
Headquarters 36B-11L, Namdong Industrial Complex, Namdong-Gu, Incheon, Korea PHONE: +82.32.814.1540 FAX: +82.32.814.5381
WWW.DRAGON.CO.KR
51
gear train
The Gear and Power Transmission Research Laboratory: Where Innovation Thrives
Jack McGuinn, Senior Editor When, in 1980, OSU professor Donald R. Houser created the Gear and Power Transmission Research Laboratory then known as the Gear Dynamics and Gear and Power Transmission Laboratory (GearLab) he did so with the seed money provided by just three companies. Thirty-three years out, the
lab has continued to grow, impress andmost importantly succeed; it now boasts a roster of some 50 sponsoring companies and government agencies. In 2003 GearLab merged with a research group headed up by Professor Ahmet Kahraman (see interview to follow), who was then at the University of Toledos Center for Gear Research. The partnering led to a dramatic expansion of GearLab capabilities and facilities, in turn leading to explorations into the farther reaches of gear and power transmission research. Kahraman in 2006 assumed directorship of the center, as Houser retired from active teaching. All along, the GearLab has been on a mission, a mission dedicated to aiding its participating (sponsoring) industries and government agencies by enhancing gear and power transmission technology through fundamental and applied research and transfer research results; providing graduate and undergraduate students with applied educational and research opportunities in gear- and power transmission-related disciplines; and keeping sponsors updated on the latest gear and transmission technologies. The referenced sponsors are members of the GearLab Consortium. The group includes some of the biggest and most influential companies and agencies in the country. Among Consortium membership benefits: Access to research findings with good leverage of investment Licenses to state-of-the-art computer software for gear design and analysis Access to experimental databases of GearLab Access to past GearLab research in the form of papers, reports and theses Limited consulting services, free of charge And what is required of would-be Consortium members? $12,000 per year for companies with more than 250 employees; one-time initiation fee of $4,000 for new members $4,000 per year for companies with fewer than 250 employees; one-time initiation fee of $1,000 for new members It is a perfect win-win for both the lab and the companies and government agencies that support ittrue American capitalism at work. On one hand, interested and paying parties are served by some of the best engineering minds and most sophisticated testing equipment in the world, as GearLab personnel are charged with researching, say, a potentially major application or material breakthrough, etc. On the other, we, as a nation along with the gear and its ancillary industries (and
their stockholders) benefit greatly from the work being done there. And one more invaluable benefit: engineers aspiring or veteran are able to work their wonders confident in the knowledge that they are set up for successnot failure. Example: since its inception, research dollars at GearLab at have exceeded $15 million. A sampling of previous and ongoing Consortium-funded projects include: An experimental and theoretical investigation of modulation sidebands of planetary gear trains A model to predict overall transmission error of a planetary gear set Development of a load distribution model for spiral bevel and hypoid gears Development of a straight bevel gear load distribution model A model to predict overall transmission error of a planetary gear set Some Consortium member companies: Gleason Corp.; Honeywell; Hyundai; Hyundai Heavy Industries; ITAMCO; John Deere; Rexnord; Meritor; Kawasaki Machine Industry; Pratt & Whitney; Moog; and Reishauer. And government agencies/cabinet departments: Department of Energy (DOE), the Army Research Laboratory, and the National Renewable Energy Laboratory (NREL). Perhaps most important of all is the fact that, according to the Gear and Power Transmission Research Laboratorys Website (gearlab.org), over 150 Masters and Ph.D. students have been supported and mentored by the GearLab, most of whom are now helping to fill those critical positions at gear and power transmission companies that often go unfilled when vacated by their retiring predecessors. And the GearLab is where two influential industrial short courses on gear noise now considered industry-standard chapter-and-verse were developed and offered to the industry by Drs. Houser and Rajendra Singh
[www.geartechnology.com]
52
educating more than 1,350 engineers from over 320 companies on the subject matter. The GearLabs state-of-the-art facilities in the Scott Laboratory (since the 2006 renovation) include the Gleason Gear and Power Transmission L aborator y, bequeathed by the Gleason Family Foundation. The facility consists of six high-bay rooms and 4,000 square feet of laboratory space with built-in facilities such as isolated test beds and two computational research laboratories that house the research team. The test facilities are arranged in three laboratories, dedicated to experimental investigation of different aspects of gearing. There is the Gear Dynamics Research Laboratory, which houses a number of state-of-the-art test setups and machines to investigate the behavior of gear pairs and gear systems under dynamic operating conditions. It includes the Gear Dynamics test machine designed to measure transmission error, vibrations and root strains of spur and helical gears with or without shaft misalignments. Both encoderand accelerometer-based transmission error measurement systems are incorporated with this test machine. Another valuable test set-up is a planetary test gear machine to measure planet load sharing, efficiency and dynamic behavior of planetary gear sets under loaded conditions. Other test set-ups in this lab include a lowspeed load dynamometer currently being used for planetary gear set and hypoid transmission error measurements, as well as a full-scale transmission dynamometer suitable for loaded dynamic tests of gearboxes, transmissions and spin tests of axles. The Gear Efficiency and Fatigue Research Laboratory also features a number of test machines, designed specifically to evaluate the efficiency and durability aspects of gears, gear materials and lubricants: Two twin-disk test machines for contact fatigue, scoring and traction measurements; an efficiency test machine with helical gear efficiency fixtures that is
weve created a
monster.
Applied Process Inc. makes bigger parts, better.
Only Applied Process has the furnace and the finesse to produce austempered iron and steel parts that weigh in excess of 10 tons. Parts that are stronger, lighter, quieter, more wear resistant. Parts that contribute to more energy efficient operations in countless applications, from wind energy to forestry to rail transportation. Parts that increase performance while decreasing overall cost of production. We call them Monster Parts. Contact us to learn more.
Home to some of the most sophisticated gear testing and monitoring equipment on the planet, the OSU Gear and Power Transmission Research Laboratory boasts a gear dynamics test machine designed to measure transmission error, vibrations and root strains of spur and helical gearswith or without shaft misalignments. Also on the premises are three standard FZG gear durability test machines (next page) for performing pitting, tooth bending fatigue and scoring tests.
Increased Capacity!
www.appliedprocess.com
53
gear train
The Consortium, comprised of sponsoring companies and government agencies, is what keeps the lights on at the Gear and Power Transmission Research Laboratory. Consortium members need for invaluable research and developmentand their willingness and ability to pay for itare the drivers for the valuable work done there by lab personnel (all photos courtesy Gear and Power Transmission Research Laboratory).
designed to evaluate loaded and unloaded power losses of gear pairs under high-speed (up to 10,000 rpm) and high-load conditions (up to 700 Nm); three standard FZG gear durability test machines for performing pitting, tooth bending fatigue and scoring tests; and an MTS load frame fixture to perform singletooth bending fatigue tests. The third facility, the Gear Metrology Research Laboratory, supports the experiments occurring in the other two laboratories by providing systems for the measurement of surface roughness and tooth profiles, and imaging the test surfaces. A Gleason-Goulder single-flank, unloaded transmission error tester, a Gleason M&M gear CMM, a Taylor Hobson Tally-Surf surface roughness profiler and miscellaneous digital microscopes and data collection and analysis instrumentation are also available in this lab. Add to all this a priceless cache of research-specific technical papers produced in-house over the years and typically presented at VDI- and ASME-sponsored conferences. Bottom line after the money has been spent, the checks have been cashed and the work completedvirtually every project the Gear and Power Transmission Research Laboratory takes on is done so with the following goals firmly in its sights: Increase power density Improve quality Reduce noise and vibration Improve efficiency and lubrication Reduce cost of power transmission and gear systems It is, after all, what gear systems designers strive for every day. And what is accomplished at the Gear and Power Transmission Research Laboratory the GearLab on a daily basis. (For more on the Gear and Power Transmission Research Laboratory, please see accompanying Q&A with lab director Ahmet Kahraman.)
www.zoller-usa.com
Ahmet Kahraman, professor and director Gear and Power Transmission Research Laboratory DepartmeThe Ohio State University 201 W. 19th Avenue Columbus, OH 43210 Phone: (614) 292-4678 Fax: (614) 292-3163 kahraman.1@osu.edu
[www.geartechnology.com]
19.12.2012 10:32:50
54
Z_Variante_1_ad_hobCheck_89x247_5_US.indd 1
A Gear Technology Interview with Ahmet Kahraman, Director, Gear and Power Transmission Research Laboratory
Jack McGuinn, Senior Editor
Gear Technology (GT). Can you tell us about the projects sponsored at the GearLab?
Dr. Ahmet Kahraman (AK). Projects sponsored by the OSU Gear Research Consortium cover a wide spectrum of gear topics, including gear design optimization; gear contact mechanics; gear system dynamics; gear tribology and lubrication; gear system efficiency; contact and bending fatigue; surface wear; and scuffing. At any given time, we will have 710 (masters and doctorate) students supported by the Consortium to perform such research projects. Research findings are presented to the Consortium members and implemented in our software packages that are licensed to the members. companies, and the rest are from manufacturing, oil, consulting, software and recreational vehicle industries. As such, while we are involved with the automotive industry heavily, we cannot say our research is limited to automotive needs only. Our sponsor base is rather diverse, covering various industries. tial is perhaps one reason. U.S. universities will not hire new professors to work on gears, as this is not as high on their lists as other emerging areas, such as nano or bioengineering. Meanwhile powertrain industries have been dealing with real, tough and perennial issues that require immediate attention. (Another) reason might be that U.S. powertrain companies are not that enthusiastic about university research perhaps due to their past experiences. There is still a perception that academic research is not applicable to practical problems. I would like to think that our projects in GearLab are examples to make a case that academic research can be done to investigate a science issue while at the same time solving a particular real-life problem of industry.
GT. Assuming the GearLab is international in scope, are U.S. national security considerations ever a factor in working with a foreign entity?
AK. Yes, GearLab has an international focus and reach. Of 67 current members of the consortium, about one-third are non-U.S. companies from countries such as S. Korea, Japan, Germany, Italy, France, U.K., China, Turkey, Sweden, Canada and Mexico. Yet we are trained and set-up to perform research with ITAR (International Traffic in Arms Regulations) or export controls restrictions as well. We currently have several projects of this type and we have systems in place to fully comply with such requirements.
GT. What are individually sponsored projects, and how do they work?
AK. These are the projects funded by a single company, while on some occasions more than one company might partner up to fund a project. The sponsoring company may or may not be a member of the Gear Research Consortium. (The) sponsoring company funds the entire project exclusively. The results of these projects are kept confidential (i.e., they are not shared with the Consortium membership). A research contract agreement is signed between the company and the University to address all legal issues including non-disclosure, licensing as well as publications.
GT. What can be done to enlist more bright young people in mechanical and power transmission components engineering?
AK. Our strategy has been involving undergraduate students in gear research as early as possible. We engage sophomores and juniors actively and hire them as undergraduate research assistants early on. Once they become a part of GearLab and witness what we are all about, they typically stay with us through their graduate education.
GT. What would you consider the GearLabs greatest achievement to date?
AK. While we are proud of the positive impact of our research on the gear and power transmission industries, and our contributions to the stateof-the-art in gearing, our greatest achievement within the last 30 years has to be our educational impact on the industry. We graduate about 10 students with (masters and doctorates) in gearing-related topics each year who are hired exclusively by power transmission companies. We have more than 175 GearLab alumni working in industry on gears and power transmissions; you can trace a many practicing gear engineers to GearLab. In addition, we also provide gear-related, industrial short courses. More than 1,500 engineers (have taken) our industrial courses over the years. As such, GearLabs greatest achievement has to be that it was able to educate gear technologists needed by the industry.
GT. Is your work split evenly between government and industry, or something else?
AK. We work with government entities such as the (Department of Energy, National Renewable Energy Laboratory and the Army Research Laboratory) on the Federal side, while more than 80 percent of our current funding is industrial in nature.
GT. In reviewing the GearLab site, it appears that a majority of your research is automotive-related. Accurate? If so, why the emphasis?
AK. About half of our research expenditures are automotive-related, while the rest is aerospace- and off-highway-related. Of 67 current consortium member companies, about 25 are automotive (OEM and 1st Tier suppliers), 10 are aerospace, 20 are off-highway and industrial gearbox
is a Howard D. Winbigler professor of mechanical and aerospace engineering at The Ohio State University, and director of the Gleason Gear and Power Transmission Research Laboratory. He also directs the Pratt & Whitney Center of Excellence in Gearbox Technology. Kahraman was past chairman of the ASME Power Transmission and Gearing (PTG) Committee and the 2007 and 2009 ASME PTG Conferences. A former associate editor of the ASME Journal of Mechanical Design, he serves on the editorial boards of Journal of Sound and Vibration, Journal of Multi-Body Dynamics, and Mechanics-Based Design of Structures and Machines. Kahraman is an ASME fellow and member of STLE. He received his Ph.D. degree in mechanical engineering from Ohio State in 1990. His areas of research focus include gear system design and analysis; gear and transmission dynamics; gear lubrication and efficiency; gear and fatigue life prediction; and test methodologies.
55
Workholding Options
question
Email your questionalong with your name, job title and company name (if you wish to remain anonymous, no problem) to: jmcguinn@ geartechnology.com; or submit your question by visiting geartechnology.com.
We manufacture some gears that require an axial face as a datum, as well as locating on the bore for centering. Other gears use only the bore for both axial and radial locating. What type of workholding is appropriate for each type of part? Is there workholding that will work for both types?
Response from Hank Kohl, president, Hainbuch America Corporation For the parts with a bore that is the radial datum and an axial face, a pull-down-type mandrel is most effective. As the part is centered on the bore, the collet pulls the parts down against an end-stop for the axial reference. These can be with or without a draw bolt, thus allowing a blind-hole application. When parts that have only a bore for datum, a deadlength mandrel is appropriate. These expand only on the bore and do not pull against the face. This prevents a nonPull-down mandrel (illustrations
courtesy Hainbuch).
datum-surface from affecting the alignment of the part during clamping. For the flexibility to use both types, a quickchange systemconsisting of a flange and actuDead-length mandrel. ating unit will enable a fast changeover from pull-down to dead-length. These are generally off-the-shelf, standard components. Hank Kohl
Second response from Chris Brown, business manager for Forkardt, an ITW Workholding Company. For gripping on only an ID bore, a collet or expanding mandrel are usually the preferred method; this is when there are no other datums to locate from. Typically, the manufacturing process will use centers for putting the gear on a common centerline, and the collet/mandrel is used for securing the gear while under rotation and against any torque applied during the process. This is very common in gear hobbing. Where centers are not used, accuracy will be dependent on a collet fixture, as centerline will be established by the accuracy of the fixture, as opposed to the accuracy of the centers. When centering on the ID is requiredalong with an axial face as a locating datuma pull-down chuck is recommended. This most likely would be a collet chuck that pulls the gear down against a positive stop or locating face. These are typically not something that the buyer can purchase off the shelf, but more likely requires some design work that can be accomplished in some instances rather easily. But for more complex or demanding applications, contacting a workholding company is advised. Designs of this type can accommodate diameters as small as .5" (12 microns) and up to 40" (1 meter) or larger. Regarding larger instances, if a collet is not used, some form of either manual or power chucks are used. The key will be to pull the gear back against a qualified surface in order to hold any GD&T requirements. Collets would be most commonly used, however, due to the need to locate on an axial datum; a special fixture would be needed to accommodate both examples. It can be accomplished relatively easily by eliminating the locating detail on the fixture. Chris Brown
56
[www.geartechnology.com]
Gear expo
across the country and abroadall in one highly accessible locationall at one time.
) See the machines in action and inspect
2013 is the worlds only conference and expo exclusively for the gear industry. Dont miss out and have to wait another two years for this kind of unique opportunity.
trusting partnerships.
Visit www.gearexpo.com for information on registering, travel, the exhibit hall, and more.
www.Gearexpo.com
technical
Producing Large-Sized, Skew Bevel Gear Pinion Using Multi-Axis Control and Multi-Tasking Machine Tool
I. Tsuji, K. Kawasaki and H. Gunbara
This paper proposes a method for the manufacture of a replacement pinion for an existing, large-sized skew bevel gear using multi-axis control and multitasking machine tool.
Introduction
Bevel gears are used to transmit power and motion between the intersecting axes of two shafts, most often mounted on shafts 90 apart. They may have straight, Zerol, spiral or skew teeth (Refs. 14), and are common in gear transmissions (Ref. 5). The transmission of straight bevel gears is regarded as a particular case of skew bevel gears (Ref. 6) in that their contact ratio is larger than that of straight bevel gears and skew bevel gears have oblique teeth. Skew bevel gears are typically used in power generation plants and are quite large. In recent years these mostly aging plants have been undergoing extensive retrofitting and so it has often become necessary to replace the skew bevel gears used in them. In some cases, where only the pinion member is changed, it then becomes necessary to manufacture a new pinion that performs well with the existing gear member. It is now possible to machine these gears complicated tooth surface due to the development of multi-axis control and multitasking machine tools (Refs. 78). Therefore, high-precision machining of large-sized, skew bevel gears has become commonplace. Proposed here is a method for manufacturing new pinion mates for large-sized, skew bevel gears using multi-axis control and multitasking machine tools. This manufacturing method has the dual advantages of arbitrary modification of the tooth surface and of machining the part without the tooth surface (Ref. 9). To begin, understand that the tooth surface forms of skew bevel gears are modeled mathematically. Next, the real tooth surfaces of the gear member are measured using a coordinate measuring machine (CMM), and the deviations between the real and theoretical tooth surface forms are formalized using the measured coordinates. It is now possible to analyze the tooth contact pattern and transmission errors of the skew bevel gears while addressing the deviations of the real and theoretical tooth surface forms by expressing the deviations as polynomial equations. The components of the deviations of tooth surface forms corresponding to the distortions of heat treatment and lapping, etc., are used because the motion concept can be implemented on the multitasking machine. Further, deviations of the tooth surface forms of the gear member can be reflected in the analysis of the tooth contact
pattern and transmission errors, and the tooth surface form of the pinion member that has good performance mating with the existing gear member is determined. Finally, the pinion member is manufactured by a swarf cutting that is machined using the side of the end mill of a multi-axis control and multitasking machine tool. Afterward, the real tooth surfaces of the manufactured pinion member are measured using a CMM and the tooth surface form errors are detected. Although the tooth surface form errors were especially large on the coast-side, they are in fact minimal on the drive-side. In addition, the tooth contact pattern of the manufactured pinion member and the provided original gear member were compared with the results from tooth contact analysis (TCA), and there was good agreement.
As mentioned, the tooth surface forms of skew bevel gears are modeled mathematically. In general, the geometry of the skew bevel gears is achieved by considering the complementary crown gear as the theoretical generating tool. Therefore, the tooth surface form of the complementary crown gear is considered first. The number of teeth of the complementary crown gear is represented by:
zp zg zc= = sin p0 sin g0
(1)
where: zc is number of teeth of complementary crown gear zp is number of teeth of the pinion zg is number of teeth of the gear p0 is pitch cone angles of the pinion g0 is pitch cone angles of the gear Figure 1 shows the tooth surface form of the complementary crown gear assuming to be straight bevel gears with depth-wise tooth taper. O-xyz is the coordinate system fixed to the crown gear and the z axis is the crown gear axis of rotation. Point P is a reference point at which tooth surfaces mesh with each other and is defined in the center of the tooth surface. The circular arcs with large radii of curvatures are defined both in xz and xy planes; the xz and xy planes correspond to the sections of the tooth profile and tooth trace of the tooth surface, respectively.
Printed with permission of the copyright holder, the American Gear Manufacturers Association, 1001 N. Fairfax Street, Fifth Floor, Alexandria, VA 22314-1587. Statements presented in this paper are those of the author(s) and may not represent the position or opinion of the American Gear Manufacturers Association.
58
[www.geartechnology.com]
This curved surface is defined as the tooth surface of the complementary crown gear. The following equations demonstrate the relations between c, c and Mn in xz, and between s, s and b in xy planes, respectively (Ref. 10). Since skew bevel gears have teeth that are straight and oblique, the skew bevel gear has in fact a skew angle (Fig. 2). Thus the complementary crown gear also has the skew angle, defined as . The tooth surface of the complementary crown gear is expressed in O-xyz using c and s:
Mn c + cos c= 2c
2
( )
2
(2)
s2+ b 4 s= 2s
where: c = radius of the curvature of the circular arcs in the xy plane, and has influence on c c = amount of tooth profile modification Mn = normal module = pressure angle s = radius of curvature of the circular arcs in the xy plane, and influence on s s = amount of tooth profile crowning b = facewidth
X (u,)=
coordinate system O-xsyszs and is fixed in space. When is zero, O-xsyszs coincides with O-xyz. Assuming the relative velocity W (X) between the crown gear and the generated gear at the moment when generating angle is , the equation of meshing between the two gears is as follows (Refs. 1112):
N (u, ; ) W (u, ; )=0
(4)
where: X = position vector of tooth surface of complementary crown gear in O-xyz u = parameter which represents curved lines = parameter which represents curved lines Rm = mean cone distance The unit-normal X is expressed by N. The equation of the tooth surface of the complementary crown gear=X. The complementary crown gear is rotated about the z axis by angle and generates the tooth surface of the skew- bevel gear. This rotation angle of the crown gear, is the generating angle. When the generating angle is , X and N are rewritten as X and N in O-xsyszs, assuming that the coordinate system O-xyz is rotated about the z axis by in the
c (cos cos ) s (1 cos u)+s sin u tan s sin u+Rm c (sin sin )
(3)
where: N = the unit-normal vector of X in O-xsyszs X = position vector of tooth surface of complementary crown gear in O-xsyszs = parameter representing rotation angle of complementary crown gear about the z axis From Equation 4 we have = (u,). Substituting (u,) into X and N, any point on the tooth surface of the crown gear and its unit-normal are defined by a combination of (u,), respectively. When the tooth surface of the complementary crown gear in O-xsyszs is transformed into the coordinate system fixed to the generated gear, the tooth surface of the skew-bevel gear is expressed. The tooth surfaces of the pinion and gear are expressed as xp and xg, respectively. Moreover, the unit-normals of xp and xg are expressed as np and ng, respectively. Henceforth, the subscripts p and g indicate that each is related to the pinion and gear.
Manufacturing errors occur in bevel gear cutting, sometimes because whether the mathematical model, as mentioned earlier,
March/April 2013|GEAR TECHNOLOGY
59
technical
fits the real tooth surface of the existing gear member or not, is not obvious. Therefore the tooth surfaces of the gear member are measured using a CMM and the deviations between the real and theoretical tooth surface forms are formalized. Coordinate measurement of real tooth surface. The theoretical tooth surfaces of the gear member are expressed as xg (ug,g), as mentioned. A grid of n lines and m columns is defined and a point or reference point is specified on the tooth surfaces of both the drive- and coast-sides; the reference point is usually plotted in the center of the grid. The position vectors xg (x, y, z)namely, u, and are determined for the solution of simultaneous equations by considering one point on the grid of the tooth surface; the unit-normal (nx, ny, nz) of the corresponding surface point is also determined since u, and are determined (Ref. 13). For measurement, the gear member is set up arbitrarily on a CMM whose coordinate system is defined as Om-xmymzm. We can make origin Om and axis zm coincide with the origin and the axis of the gear member, respectively. The whole grid of surface points, together with the theoretical tooth surfaces, is rotated about the zm axis so that ym is equal to zero at the reference point. Therefore, the position vector of the point and its unitnormal are transformed into the coordinate system Om-xmymzm and are represented by:
(5)
Formalization of deviations of tooth surface form. Based on the method mentioned earlier, the deviation for each point on the grid is calculated when the points on the tooth surface are measured (Ref. 15). However, it is difficult to ideally fit to the theoretical tooth surface because varies at each point on the grid. We therefore define (X, Y) whose X and Y are toward the directions of the tooth profile and tooth trace, respectively, and form the following polynomial expression:
=11+12+21+22+31+32+41
(8)
where: 11 = parameter-defining deviation 12 = parameter-defining deviation 21 = parameter-defining deviation 22 = parameter-defining deviation 31 = parameter-defining deviation 32 = parameter-defining deviation 41 = parameter-defining deviation Figure 3 shows the procedure formalizing the relation between the fundamental components of polynomial expression and the deviation of tooth surface form. First, the tooth trace deviation 11 and tooth profile deviation 12 are expressed as the following first-order equations of X and Y, using fundamental components a11 and a12, respectively (Fig. 3a):
11=a11 X a11= 11 0.5 H 12=a12 Y a12= 11 0.5 T
(9)
where: x(i) is the position vector of the i-th point of tooth surface in Om- xmymzm n(i) is the unit-normal vector of x(i) The real tooth surface of the gear member was measured using a CMM (Sigma M and M3000 developed by Gleason Works). When the real tooth surface is measured according to the provided grid, the i-th-measured tooth surface coordinates are obtained and numerically expressed as the position vector (Refs. 1314):
(i) (i) (i) (i) T xm =(xm , ym , zm ) (i=1, 2, , 2nm)
where: a11 = fundamental component of polynomial expression H = range of the evaluation of the tooth surface in X directions a12 = fundamental component of polynomial expression T = range of the evaluation of the tooth surface in Y directions The tooth trace deviation 21 and tooth profile deviation 22 are expressed as the following second-order equations of both X and Y, using fundamental components a21 and a22, respectively (Fig. 3b):
21=a21 X2 21 = a21= (0.5 H)2 22=a21 Y2 22 = a22= (0.5 T)2
(10)
(6)
where: (i) Xm is the position vector of the i-th-measured tooth surface coordinates in Om-xmymzm When the deviation between the measured coordinates and nominal data of the theoretical tooth surfaces for each point on the grid is defined towards the direction of the normal of the theoretical tooth surface, i-th can be determined by: where: the deviation between measured coordinates and nominal data of tooth surface is (i) for each point on the grid towards the direction of the normal of tooth surface; is equal to zero at the reference point. The fundamental components of the deviations of tooth surface forms corresponding with the distortions of heat treatment and lapping, etc., are used because the motion concept may be implemented on a multitasking machine.
(i) (i) (i) (i) =(xm - x ) n (i=1, 2, , 2nm)
4 21 H2 4 22 T2
(7)
where: a21 = fundamental component of polynomial expression a22 = fundamental component of polynomial expression Further, the deviations 31 and 32 in the directions of the biasin and bias-out are expressed as the following second-order equations of both X and Y, using fundamental components a31 and a32, respectively (Fig. 3c):
1=tan1
( )
(11)
T , = H H L0 cos 1
[www.geartechnology.com]
60
31=a31 (X cos 1 Y sin 1)2 31 = 4 31 a31= 2 (0.5 L0)2 H0 32=a32 (X cos 1 Y sin 1)2 32 = 4 31 a32= 2 (0.5 L0)2 L0
where: a31 =fundamental component of polynomial expression a32 =fundamental component of polynomial expression The tooth trace deviation 41 is expressed as the following third-order equations of X and Y, using fundamental components b1, b2 and b3, respectively (Fig. 3d):
41=b3X3+b2X2+b1X
(12)
Thus b1, b2 and b3 are determined from the following conditions: is equal to zero when X=-0.5H and X=0.5H. In addition, is equal to 41 when X=0.25H. Reflecting the polynomial expression to the theoretical tooth surface, the position vector is represented by:
xa=x+ n
(13)
Figure 3 Procedure formalizing relation between fundamental components of polynomial expression and deviation of tooth surface form.
Thus xa describes the theoretical tooth surface with consideration of the tooth surface form deviations. The tooth contact patterns and transmission errors with the tooth surface form deviations are analyzed using xa. The position vector of the i-th (i) point of the theoretical tooth surface is expressed as xa .
The real tooth surfaces of the gear member to be used were measured on a CMM and the deviations between the real and theoretical tooth surface forms were formalized. Table 1 shows the dimensions of the skew bevel gears. The pitch circle diameter of the gear member is 1,702.13mmvery large. Five points in the direction of the tooth profile and nine points in the direction of the tooth trace for the grid were used. Figure 4 shows the formalized results of the measured coordinates. Figure 4a shows the measured results using a CMM compared to the theoretical tooth surface. Figure 4b shows the formalized results using Equations 9, 10 and 11 in Equation 8. Figure 4c shows the formalized results using Equation 12, in addition to Equations 9, 10 and 11 in Equation 8. The maximum values of the magnitude of deviations are 0.793 mm, 0.128 mm and 0.066 mm in Figure 4a, b and c, respectively. The overall deviations gradually decrease as a whole from Figure 4a and 4c. As the deviations are formalized with a large number of equations, the deviations decrease and fit the measured coordinates well to the theoretical tooth surface. Therefore, once formalization of the deviations was validated the fundamental components of the deviations of the tooth surface forms corresponded to the distortions of heat treatment and lapping, etc.
Concept of tooth contact analysis. The tooth surface form of the pinion member that has good performance mating with the existing gear member mentioned earlier is considered based on tooth contact analysis. In this case, the tooth surface form of the
Figure 4 Formalized results based on measured coordinates.
March/April 2013|GEAR TECHNOLOGY
61
technical
pinion member is modeled using Equation 1and the appropriate amount of profile modification and crowning is calculated. The pinion and gear members are assembled in a coordinate system Oh-xhyhzh (Fig. 5) in order to analyze the tooth contact pattern and transmission errors of the pinion member and existing gear member. Suppose that p and g are the rotation angles of the pinion and gear, respectively. The position vectors of the pinion and gear tooth surfaces must coincide and the direction of two unit-normals at this position must be also agree in order to contact the two surfaces. Therefore, the following equations yield:
B(p) xp(up, p)=C(g) xg(ug, g) B(p) np(up, p)=C(g) ng(ug, g)
(14)
where: B and C are the coordinate transformation matrices for the rotation about the yh and zh axes, respectively p is the rotation angle of pinion about yh axis in Oh-xhyhzh g is the rotation angle of gear about zh axis in Oh-xhyhzh
cos p 0 sin p 0 1 0 B(p)= sin p 0 cos p cos g sin g 0 C(g)= sin g cos g 0 0 0 1
Since |np|=|ng|=1, Equation14 represents a system of five scalar, non-linear equations with five unknownsup, p, ug, g and gconsidering angle p as the input parameter. The continuous solution of the system of the non-linear equations permits the determination of the path of contact considering that p changes every moment. A method of successive approximation is utilized in order to obtain a numerical solution of Equation 14. In this case it is convenient to use a cylindrical coordinate system. The paths of contact on the pinion and gear tooth surfaces are represented by xp (up, p) and xg (ug, g), respectively. When the pinion is rotated by the angle p the gear should be rotated by the angle zp/zgp, assuming that pinion and gear are conjugate. Realistically, however, this is not the case, and transmission errors occur. The function of transmission errors is defined as:
z g (p)=g (p) zp p g
(16)
[ [
] ]
(15)
where: g =function of transmission error Results of TCA. The tooth contact pattern and transmission errors of the pinion member model (Eq. 1) and existing gear
Table 1Dimensions of skew bevel gears Pinion Gear Number of teeth zp, zg 18 116 Pitch circle diameter 264.1346 mm 1702.1302 mm Pitch cone angle p0, g0 8.8167 deg 81.1833 deg Normal module Mn 10.6764 Mean cone distance Rm 759.65 mm Pressure angle 14.5 deg Skew angle 15 deg Face width b 203.2 mm Shaft angle 90 deg Backlash 0.4064 - 0.5588 mm
(b) Coast side Figure 5 Meshing of pinion and gear. Figure 6 Analyzed results of tooth contact pattern and transmission errors without accounting for tooth surface form deviations.
[www.geartechnology.com]
62
member whose tooth surface is calculated under unloaded condition were analyzed based on the method used earlier. Figure 6 shows the analyzed results of tooth contact pattern and transmission errors, without taking into account the tooth surface form deviations described earlier. Figure 6a is the result of drive-side, and Figure 6b is that of the coast-side. The amounts of tooth profile modification and crowning of pinion member are c=0.05mm and s=0.05mmon both driveand coast- sides respectively. These values have influence on the tooth contact pattern and transmission errors, as mentioned. The right side from the center (Fig. 6) shows the analyzed contour line on the gear tooth surface at every instant when the rotation angle p of the pinion changes from 12.5 to -27.5 on the drive-side, and from -12.5 to 27.5 on the coast-side. The lowest figure of the right side shows the total tooth contact pattern considering contact ratio. The region whose clearance between the pinion and gear tooth surfaces is less than 30 mm is displayed. The tooth contact patterns are obtained around the centers on the tooth surfaces of both drive- and coast-sides. The left side (Fig. 6) shows the analyzed transmission errors. The shape of transmission errors is parabolic; the parabolic transmission errors occur due to the influence of both profile modification and crowning. In this case the rotation is transmitted
smoothly. Therefore it is important to have the intersection before and after meshing. The maximum value of the transmission errors is about five arcsec of both drive- and coast-sides. These transmission errors can be adjusted by changing c and s. Figures 6 and 7 show the analyzed results of tooth contact pattern and transmission errors with respect to the tooth surface form deviations. The amount of tooth profile modification and crowning of pinion member are c=0.1mm and s=-0.4mm on the drive-side, and c=0.2mm and s=0.79mm on the coast-side. In addition, -0.4 in and 0.05 in on the driveside and -0.25 in , 0.03 degrees in are changed. The tooth contact pattern deviates slightly from the center on the tooth surface of both drive- and coast-sides. These contact patterns seem to be acceptable in practical use. In addition, the transmission errors become large on the coast side. These transmission errors also seem to be acceptable in practical use.
The pinion member was manufactured using a 5-axis control machine (DMG Co., Ltd. DMU210P) based on the results of TCA. In this case the reference and hole surfaces, in addition to the tooth surfaces, can be machined and a tool approach provided from optimal direction using multi-axis control since the structure of the 2-axis of the inclination and rotation in addition to translational 3-axis are added; therefore, a thicker tool can be used. This should reduce the machining time and produce a smoother tooth surface. The radius end mills made of cemented carbide for a hard cutting tool were used in the machining of tooth surface. The number of edges is six and the diameter of end mill is 10 mm. Ball end mills were used in the machining of the tooth bottom. The number of the edges is six and the diameters of end mills are 10mm and 5mm, respectively, in the machining of the tooth bottom. The pinion material used was 18CrNiMo06. The tool pass was 1mm for the large-sized pinion member. First, the pinion work was rough-cut and heat treated. Afterward, the pinion member was semi-finished with the machining allowance of 0.3mm after heat treatment. Finally, the pinion was finished with the machining allowance of 0.05 mm by swarf cutting. Machining with high accuracy and efficiency utilizing the advantages of a multi-axis control and multitasking machine tool in swarf cutting can be expected. Table 2 shows the conditions for semi-finishing and finishing of the pinion tooth surfaces. Figure 8 shows the situation of swarf cutting of the pinion member. The machining time of one side in roughcutting is about 50 minutes; semi-finishing and finishing take about 170 minutes; the machining was finished without problems, such as defects of the end-mill.
(b) Coast side Figure 7 Analyzed results of tooth contact pattern and transmission errors with respect to tooth surface form deviations.
The manufactured pinion tooth surfaces were measured using a CMM and compared with nominal data determined from the theoretical pinion tooth surface mating with the theoretical gear tooth surfaceand without taking into account tooth surface form deviations. Figure 9 shows the measured result of the pinion member. Since tooth surface form deviations were not respected in the theoretical gear tooth surface, the tooth surface form errors are relatively large. In particular, the tooth surface form errors are large on the coast-side. The large-sized
March/April 2013|GEAR TECHNOLOGY
63
technical
Table 2 Conditions of pinion machining Diameter of Revolution of main Feed, Depth of Time/one Processes end mill, mm spindle, rpm mm/min cut, mm side, min Semi-finishing 10.0 1400 1100 0.2 120 Finishing 10.0 1600 1100 0.05 420
In this paper a manufacturing method of the pinion member of large-sized skew bevel gears using multiaxis control and multitasking machine tool respecting the existing gear member was proposed. The main conclusions obtained in this study are summarized as follows: The tooth surface forms of skew bevel gears were modeled mathematically. The deviations between the real and theoretical tooth surface forms were formalized using the measured coordinates of the real tooth surfaces of the gear member. The tooth surface form of the pinion member that has good performance mating with the existing gear member was determined using the results of tooth contact analysis. The pinion member was manufactured by swarf cutting using a multi-axis control and multitasking machine tool. The real tooth surfaces of the manufactured pinion member were measured using a CMM and the tooth surface form errors were detected. The experimental tooth contact patterns of the existing gear member and manufactured pinion member were compared with those of tooth contact analysis. As a result, there was good agreement.
1. Tsai Y.C. and Chin P.C. Surface Geometry of Straight and Spiral Bevel Gears, ASME Journal of Mechanisms, Transmissions and Automation in Design, 1987, 109, pp. 443-449. 2. Townsend, D.P. Dudleys Gear Handbook, 2nd Edition, Design, Manufacture and Application of Gears, McGraw-Hill, 1991 New York pp. 2.92.17. 3. Radzevich, S.P. Handbook of Practical Gear Design and Manufacture, 2nd Edition, CRC Press, 1984, p. 53. 4. Dimarogonas, A.D. Machine Design: A CAD Approach, Wiley-InterScience, 2001, pp. 869874. 5. Davis, J.R. Gear Materials, Properties and Manufacture, 2005, ASM International Technical Books Committee, pp. 9299. 6. Fuentes A., J.L. Iserte, I. Gonzales-Perez and F.T. Sanchez-Marin. Computerized Design of Advanced Straight- and Skew-Bevel Gears Produced by Precision Forging, 2011, Computing Methods of Applied Mechanical Engineering, 2011, 200, pp. 23632377. 7. Nakaminami, M., T. Tokuma, T. Moriwaki and K. Nakamoto. Optimal Structure Design Methodology for Compound Multi-Axis Machine Tools, Part I (Analysis of Requirements and Specifications), International Journal of Automation Technology, Vol. I, No. 2, 2007, pp. 7886. 8. Moriwaki T. Multi-Functional Machine Tool, Annals of CIRP, Vol. 57, No. 2, 2008, pp. 736749. 9. Kawasaki, K., I. Tsuji, Y. Abe and H. Gunbara. Manufacturing Method of Large-Sized Spiral Bevel Gears in Cyclo-Palloid System Using MultiAxis Control and Multi-Tasking Machine Tool, Proceedings International Conference on Gears, Vol. I, Garching, Germany, 2010, pp. 337348, Gear Technology 2011 and Gear Technology India 2012. 10. Kawasaki K., I. Tsuji and H. Gunbara. Tooth Contact Analysis and Manufacture on Multi-Tasking Machine of Large-Sized Straight Bevel Gears, Proceedings ASME 2011 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, 2011, Washington D.C., CD-ROM. 11. Sakai T. A Study on the Tooth Profile of Hypoid Gears, Trans. JSME, Vol. 21, No. 102, 1955, pp. 164170 (in Japanese). 12. Litvin, F.L. and A. Fuentes. Gear Geometry and Applied Theory, 2nd Ed., Cambridge University Press, 2004, UK, pp. 98101. 13. Kawasaki, K. and I. Tsuji. Analytical and Experimental Tooth Contact Pattern of Large-Sized Spiral Bevel Gears in Cyclo-Palloid System, Trans. ASME Journal of Mechanical Design, Vol.132, 04100418, 2010. 14. Fan, Q., R.S. Da Foe and J.W. Swanger. Higher-Order Tooth Flank Form Error Correction for Face-Milled, Spiral Bevel and Hypoid Gears, Trans. ASME Journal of Mechanical Design, Vol.130, 07260117, 2008. 15. Stadtfeld, H.J. Handbook of Bevel and Hypoid Gears: Calculation, Manufacturing and Optimization, Rochester Institute of Technology, 1993, pp. 912.
[www.geartechnology.com]
Conclusions
References
skew bevel gears were set on a gear meshing tester and the experimental tooth contact patterns were investigated. Figure 10 shows the result of the experimental tooth contact patterns on the gear tooth surface of the drive- and coast-sides, respectively. Although the experimental tooth contact pattern deviates from the center of the tooth surface slightly on both drive- and coast-sides, it is almost the same as that in Figure 7, with respect to the tooth surface deviations. From these results the validity of the manufacturing method of the pinion member using a multitasking machine was confirmed.
64
Praewema Honing Machines SynchroFine line of high-performance hard gear honing machines for critical gearbox applications.
Pittler T&S GmbH Application-specific lathe technology for single or multi-task operations from 20mm to 6000 mm.
WMZ GmbH Precision center-drive turning machines and modular automation solutions with reduced cycle times.
Praewema Gear Grinding Machines SynchroFine line of highperformance hard gear grinding machines for coarse pitch applications.
Profilator GmbH
Modular machines designed for gear Scudding, tooth pointing, and polygon milling.
Call us...let us show you what we can do for you.
GMTA
4630 Freedom Drive Ann Arbor, MI 48108 734.973.7800 fax 734.973.3053 www.gmtamerica.com
technical
Recent Inventions and Innovations in Induction Hardening of Gears and GearLike Components
Dr. Valery Rudnev
This paper examines the expanding capabilities of induction hardening of gears through methods like spin hardening or tooth-by-tooth techniques.
Introduction
This presentation provides a review of basic principles and applications devoted to induction hardening of small-, mediumand large-size gears using tooth-by-tooth techniques and encircling method. Depending upon the gear size, required hardness pattern and tooth geometry, gears are induction hardened by encircling the whole gear with a coil (so-called spin hardening of gears), or for larger gears, heating them tooth-by-tooth (Refs. 16).
Tooth-by-Tooth Hardening
The tooth-by-tooth method comprises two alternative techniques: tip-by-tip or gap-by-gap hardening (Refs. 14). The tip-by-tip method can apply a single-shot heating mode or scanning mode, while gap-by-gap techniques exclusively apply the scanning mode. Inductor scanning rates are typically within 6 mm/sec to 9 mm/sec. Both tip-by-tip and gap-by-gap techniques are typically not very suitable for small- and finepitch gears (modules smaller than 6) (Refs. 12). When using tip-by-tip hardening, an inductor encircles a body of a single tooth. This technique is not often used, because the hardening patterns typically do not provide the required fatigue and impact strength. Gap-by-gap hardening is a much
more popular technique compared to the tip-by-tip method. This is the reason why the term tooth-by-tooth hardening is often associated with the gap-by-gap hardening method. Gapby-gap hardening requires the inductor to be symmetrically located between two flanks of adjacent teeth. Inductor geometry depends upon the shape of the teeth and the required hardness pattern. Special locators (probes) or electronic tracing systems are often used to ensure proper inductor positioning in the tooth space. Two scanning techniques used include one where the inductor is stationary and the gear is moveable, and the other where the gear is stationary and the inductor is moveable. The latter technique is more popular when hardening large-size gears. Inductors can be designed to heat only the root and/or flank of the tooth, leaving the tip and tooth core soft, tough and ductile (Fig. 1). Though this is one of the oldest hardening techniques,
Figure 1 For tooth-by-tooth hardening, inductors can be designed to selectively harden specific areas of gear teeth where metallurgical changes are required (Ref. 2).
Figure 2 Induction gear hardening machine for large bearing ring with teeth located on exterior (courtesy Inductoheat).
Printed with permission of the copyright holder, the American Gear Manufacturers Association, 1001 N. Fairfax Street, Fifth Floor, Alexandria, VA 22314-1587. Statements presented in this paper are those of the author(s) and may not represent the position or opinion of the American Gear Manufacturers Association.
66
[www.geartechnology.com]
recent innovations continue improving the quality of gears heat treated using this method. Thermal expansion of metal during the heating should be taken into consideration when determining and maintaining the proper inductor-to-tooth air gap. After gear loading and initial inductor positioning, the process runs automatically based on an application recipe. Figure 2 shows examples of a tooth-bytooth induction hardening machine. When developing tooth-by-tooth gear hardening processes, particular attention should be paid to electromagnetic end/edge effects and the ability to provide the required pattern in the gear end areas. Upon scanning a gear tooth, the temperature is distributed within gear roots and flanks quite uniformly. At the same time, since the eddy current makes a return path through the flank and, particularly through the tooth tip, proper care should be taken to prevent overheating the tooth tip regions, in particular at the beginning and at the end of the scan hardening. Improved system design helps to maintain required hardness uniformity. Specifics of gear geometry demand a particular process control algorithm. In the past, the process control recipe was limited to an available variation of power and scan rate vs. inductor position. Recent innovations now enable inverters to independently control both power and frequency during scanning operation, which optimizes electromagnetic and thermal conditions at initial, intermittent and final stages of scanning. As an example, Figure 3 shows Inductoheats Statipower IFPt (Independent Frequency and Power control) inverter. The ability to independently change during scanning the frequency and power of an induction system represents the long-held dream of commercial induction heat treaters, since such types of set-up would provide the greatest process flexibility. Statipower IFPt is an IGBT-type power supply specifically designed for hardening and tempering applications, allowing independently adjustable frequency via CNC program in a 5-40kHz frequency range and power in the range of 10-360kW. This concept substantially expands heat treat equipment capabilities for processing parts by programming power and/or frequency changes on the fly, maximizing heating efficiency and temperature uniformity while heating complex geometry components.
Figure 3 Inductoheats Statipower IFP is an IGBT-type power supply specifically designed for induction hardening and tempering applications; it provides independently adjustable frequency via CNC programming in a 540 kHz frequency range and power in the range of 10360kW.
Gear spin-hardening (encircling inductors). Spin-hardening is the most popular approach for induction hardening gears with fine- and medium-size teeth. Gears are rotated during heating to ensure an even distribution of energy. Single-turn or multiturn inductors that encircle the whole gear can be used (Refs. 1; 36). When applying encircling coils, it is possible to obtain substantially different hardness patterns by varying process parameters. As a rule, when it is necessary to harden only the tooth tips, a higher frequency and high power density should be applied; to harden the tooth roots, use a lower frequency. A high power density in combination with the relatively short heat time generally results in a shallow pattern, while a low power density and extended heat time produces a deep pattern with wide transition zones.
67
technical
Quite often, to prevent problems such as pitting, spalling, tooth fatigue and endurance and impact limitations, it is required to harden the contour of the gear, or to have gearcontour hardening (Fig. 4). This often also maximizes beneficial compressive stresses within the case depth and dramatically minimizes distortion of as-hardened gears keeping it under 80-100 microns (0.003" 0.004"). Many times, obtaining a true contour-hardened pattern can be a difficult task due to the difference in current density (heat source) distribution and heat transfer conditions within a gear tooth. Simultaneous dual-frequency gear hardening. Some induction practitioners have heard about simultaneous dual-frequency gear hardening, which utilizes two appreciably different frequencies working on the same coil at the same time (Ref. 6). Low-frequency helps to austenitize the roots of the teeth and high frequency helps austenitize the tooth flanks and tips. However, it is not advantageous to have two different frequencies working simultaneously all the time. Many times, depending upon the gear geometry, it is preferable to apply lower frequency at the beginning of heating cycle; after achieving a desirable root heating, the higher frequency can complement the initially applied lower frequency, thus completing a job in tandem. Figure 5 shows a single-coil dual-frequency system that comprises medium-frequency (10 kHz) and high-frequency (120 to 400kHz) modules working simultaneously or in any sequence desirable to optimize properties of the heat treated gears (Ref. 6); total power exceeds 1,200kW. As expected, smaller gears will require less power. Inductoheats simultaneous dual-frequency induction gearhardening system (Fig. 5) also has some auto-match items to simplify tuning. It is rugged and can be used for high-volume, single-shot hardening of several powertrain components, dramatically minimizing distortion of heat treated parts and providing a superior hardness pattern with favorable distribution of residual stresses. Novel development in induction gear-hardeningTSH steels. There was a belief that not all gears and pinions were well-suited for induction hardening. Hypoid and bevel gears, spiral bevel automotive pinions and noncircular gears used to be rarely induction-hardened and typically carburized. This situa-
Figure 5 Inductoheats simultaneous dual-frequency inverter for gear contour hardening (courtesy Inductoheat).
tion has been changed. As an example, Figures 6a and 6b show an example of inductively case-hardened components (Refs. 78). TSH steels are low-hardenability (LH) low-alloy steels characterized by limited hardenability and a reduced tendency for grain growth during heating into the hardening temperature range. They can be substituted for more expensive standard steels typically used for conventional induction hardening or carburizing grades. TSH steels have significantly less alloying elements such as manganese, molybdenum, chromium and nickel, making them less expensive than the majority of conventional low alloy steels. Their chemical composition is somewhere between micro-alloy steels and plain carbon steels, providing fine-grain martensite with extremely high compressive stresses at the tooth surface. With TSH technology, components are usually through-heated at relatively low temperatures sufficient for austenitization or partial heated (depth of heating needs to be 2-3 times deeper than required harden depth) and then are rapidly quenched. The hardened depth is mainly controlled by the steels chemical composition. Even though components made from TSH steels are often heated through, their limited hardenability allows obtaining crisp hardness case depth with well-controlled hardness pattern having minimum case hardness deviations even when hardening complex-shaped parts (Figs. 78). In the past, it was practically impossible to induction harden components Figure 6 TSH (through-heating for surface hardening) steels uninterrupted induction-hardened shown in Figs. 69. Now it is possible to
pattern is obtained on a spiral bevel gear (courtesy ERS Engineering Corp.).
68
[www.geartechnology.com]
get those impressive, uninterrupted hardness patterns by using a simple operation: through heating those parts using low frequency inverters and water quenching. Notice that the spiral bevel pinion (Fig. 6) was induction-hardened on OD, ID and teeth region using a single operation having continuous hardness pattern. The carrier pin (Fig. 9) was induction hardened on the outside surface (1.25" diameter) and two inside diameters (longitudinal and transversal) using a single operation that also produced an uninterrupted case hardness pattern. The inside diameter of the longitudinal hole was 0.5"; the inside diameter of the transverse hole was 0.25" (Fig. 7).
Conclusions
Induction heat treating being an environmentally friendly, green and lean technology is an increasingly popular choice for induction-hardening of gears and gear-like components. Recently developed inverters and process know-how further expand its capabilities.
References
1. Rudnev, V. and D. Loveless. Handbook of Induction Heating, Marcel Dekker, NY, 2003. 2. Doyon, G., D. Brown, V. Rudnev, F. Andgea, C. Stilwala and E. Almeida. Induction Heating Helps to Put Wind Turbines in High Gear, Heat Treating Progress, September, 2009, p.5558. 3. Rudnev, V. Spin-Hardening of Gears Revisited, Heat Treating Progress, ASM Int., March/April, 2004, pp.1720. 4. Rudnev, V. Induction Hardening of Gears and Critical Components, Part 1, Gear Technology, pp. 5863, Sept./Oct. 2008. 5. Rudnev, V., Induction Hardening of Gears and Critical Components, Part 2, Gear Technology, pp. 4753, Nov./Dec. 2008. 6. Rudnev, V. Single-Coil Dual-Frequency Induction Hardening of Gears, Heat Treating Progress, ASM International, October, 2009 pp. 911. 7. Breakthrough contour hardening, ERS Engineering brochure, 2011. 8. Brayman, S., Kuznetsov, A., Nikitin, S., Binoniemi, B. and Rudnev, V., Contour hardening bevel, hypoid, and pinion gears, Gear Solutions, September, 2011, p. 30-35.
technology, for Inductoheat Inc., an Inductotherm Group Company. A Fellow of the American Society for Materials, he is known internationally as a major voice in the induction heating industry. Rudnev possesses more than 30 years of experience in induction heating, earning within the American Society for Materials and among induction heating professionals the sobriquet, Professor Induction. His credits include more than 30 patents, inventions and software registrations, as well as more than 180 published engineering/scientific works. Rudnev in 2003 co-authored the Handbook of Induction Heating, and has contributed six chapters for several other publications devoted to various aspects of induction heating, induction heat treating, computer modeling and mathematical simulations.
Figure 8 Induction-hardened automotive journal cross section (courtesy ERS Engineering Corp.).
Figure 9 Carrier pin: simultaneous OD- and ID-hardening (courtesy ERS Engineering Corp.).
March/April 2013|GEAR TECHNOLOGY
69
technical
Most audits that fail do so because they do not reveal the true nature of what is happening within the heat treatment operation. Care must be taken to look at both the quality aspects (forms, instructions, compliance) and the performance aspects (process control, work handling, etc.). Too often, audits focus their attention on the former and give a cursory look at the latter. This disconnect is the reason many organizations are confused as to why their departments or suppliers fail to achieve continuous improvement. To be useful, heat treat audits need to ask tough and realistic questions not just be forms in which the auditor fills in the blanks. The true story is
70
B. Are adequate controls employed to ensure that the processing and inspection status of the product are known throughout the heat treating operation? Are process/product monitoring and controls functions (and responsibilities) clearly defined? C. Is both the responsibility for and practice of heat treat process (recipe) development, testing methods and quality planning clearly defined? D. Does the heat treater have available and usea procedure for reviewing part design and specifications in relation to method of loading, as well as heat treat process parameter and equipment selection? E. Are process verification and/or capability studies conducted on all new part numbers? F. Are control plans and process (FMEAs) used as a basis for establishing quality programs for heat treat processes? G. What procedures are in place, and how does the heat treater react to customer concerns (internal or external indicators)? H. Are controls in place and being used on the shop floor to effectively monitor the process? I. If necessary, are statistical process control (SPC) methods utilized for key product parameters? J. Are written procedures/work instructions defining heat treat and quality functions available and in use on the shop floor (i.e., is the quality manual a living document)? K. Are adequate, in-process monitoring and inspections/tests performed, and are there adequate records? L. If on-site, does the testing or metallurgical laboratory have the tools, procedures and expertise to accurately determine part quality? If offsite, is the testing laboratory properly accredited? M. If part testing and/or PPAPs are performed, are records available with supporting documentation for the relevant heat treated products?
N. Are documented and verifiable heat treating reject, reprocessing and/or scrap records available? O. Is there an effective preventive maintenance program in place for both the heat treating and process monitoring equipment? P. Does the heat treater have an effective system for ensuring the quality from his suppliers and service providers (instrumentation calibrations, quench oil checks, etc.)? Q. Is plant cleanliness, housekeeping, environmental and working conditions conducive to a safe, efficient operation in which continuous improvement can take place? Non-Conformance (document, in detail) Major and minor non-conformances Pertinent general and specific observations Corrective Action (for each supplier location) A. Issue statement B. Corrective action(s) required C. Responsibility D. Implementation date E. Root cause found F. Follow-up plan (actions and dates)
conducted by trained and certified heat treat personnelnot just auditors skilled in the procedures involved. Both captive and commercial heat treatment organizations should demand that this aspect of their business be given the attention and respect it deserves. A standardized audit guideline with fixed frequencyof-compliance is long overdue. With ever-increasing product performance demands from customers, only continuous improvement will assure the heat treatment industry of continued growth and prosperity.
Daniel H. Herring The Herring Group Inc. +(1) 630-834-3017 dherring@heat-treat-doctor.com www.heat-treat-doctor.com
A Look at CQI9
A new automotive industry action group (AIAG) heat treat audit guidelineCQI9, Special Process: Heat Treat System Assessmentwas released in March 2006. It is intended to help standardize the heat treat audit process. The HTSA supports the automotive process approach as described in ISO/TS 16949:2002. Within each audit area, the major sections covered are: (1) process and test equipment requirements; (2) pyrometry; (3) process monitoring frequencies; (4) in-process/final test frequencies; and (5) quenchant and solution test frequencies.
Treat Doctoris owner/ operator of The Herring Group, Inc. specializing in rapid response to technical and business needs in the heat treating and sintering industry.
Summing Up
Heat treat audits are so important that, in this writers opinion, they need to be
March/April 2013|GEAR TECHNOLOGY
71
technical
Industrial production in high-wage countries like Germany remains at risk. Nevertheless, there exist examples of thriving manufacturing companies who are dominating their competitors by utilizing advanced cost-, time- and materials-saving systems to enhance their production capabilities and profit margins. The RWTH Aachen University Cluster of Excellence program (CoE) is contributing to exploring and realizing fundamental developments in the theory of production sciencein both its organizational and technical aspects (Ref. 1). To succeed in this endeavor, topdown research of entire enterprises is requiredbeginning with management, proceeding on to the process chains, and ending at single-process technology efforts. To validate the need for this work, newly gained, real knowledge is used to make real parts. Indeed, in this paper the manufacture of a modern, dual-clutch gearbox gear shaft is investigated; the main intent being to assess existing and new process chain and manufacturing technologies.
Todays complex production systems produce components and products of high complexity, requiring sophisticated yet cost-efficient process and supply chains. The production system of the mentioned gear shaft was documentedbeginning with analysis of the turned green body. This documentation includes: manufacturing technologies; completed actions; input and output conditions; and process parameters at every step of the operation. The example observed was compared to existing practices and the state-of-the-art manufacturing of gear shafts. To gain additional value the methods and results of the CoE were adapted to the optimization of the gear shaft. In practice, the CoE is divided into several parts; for this study individualized, virtual and hybrid production systems of the CoE are validated. Individualized production is the ability of production systems to be flexible for either small or large batch sizes. Virtual production means using smart software solutions to shorten, for example, construction and design processes.
Hybridproduction presents opportunities for employing different manufacturing technologies simultaneously. The optimization is achieved with both technological and economic realities in mind. This includes consulting with the customer, examining market research data and drawing upon the collective knowledge and expertise of groups like the CoE. After assessing the in-place process chain with the customer, alternative chains are developed. The proposed new process chain is analyzed concerning its potential for flexible and economic production of small-batch sizes. This is crucial in this particular scenario because, to be profitable, a production line for gear shafts must be able to produce many types of shafts over a years timeeven if it is a high-volume product. The results are then assessed using factors and protocols that are valid and practical for a company and its entire operation. These general factors are: process reliability; manufacturing costs; floor-to-floor time; required staff; investment costs; flexibility; and logistic effort. These factors help define a companys new process chain and processes. As well,
72
[www.geartechnology.com]
these factors are impactedfor good or badby weighting factors; the weighting factors are generated by a method-paired comparison. (Authors Note: the general structure in the investigation addressed by this article is in two parts: i.e.1) An investigation on gearing; and 2) Secondary machine elementsbearings, sealing surface. Validation of the gained knowledge is the end-product: a high-art, dual-clutch gearbox shaftFig. 1). The main challenges presented by this particular gear shaft are its close proximity between gear sets and the diverse bearings locations. In addition, the shaft is of a tube designspecified for lightweight needs and realization of the dualclutch concept. Through this tube a second shaftwith a connection to the second clutchis inserted. Length is about 400 mm; maximum outside diameter for the gears in the case about 90mm; the maximum outside diameter for the gears of the shown example part is less. The outside diameter of the shaft is increasing from 40mm on one side to 45mm on the other; minimum distance between the gearings is about 30mm.
An example for the assessment of manufacturing technology can be seen in Figure 2. Each realistic and possible manufacturing technology for the greenmachining of gears is assessed against
the main factor. The result is multiplied by the weighting factors and assessed leading to the given order. The ranking of broaching is superfluous here because the second power gear with smaller tip diameter cannot be broached. This approach is also used for the other manufacturing steps. The analysis method above shows that hobbing is best for green-machining, while the conclusion drawn for hardfinishing of the gears is that honing works best. Generating gear grinding is not an option because both gears on the shaft are too close together, i.e.insufficient space for the recess of the grinding worm. In this instance a new or alternative manufacturing process for power gears does not yet exist, due, perhaps, to the relatively long gaps between technological breakthroughs specific to a mature industry such as gear manufacturing. Indeed, gear manufacturing innovation requires significant investment; e.g.machine tools. The latest innovation in machining gears may be the ability to hone manufacturing parts with a near-grinding quality via power honing. Upon complete evaluation of the inplace process chain, one more optimization potential can be found in the single manufacturing process. This can be achieved by using virtual production methods such as manufacturing simulation. Therefore for the design of gear hobbing processes a manufacturing sim-
ulation is developed. Its necessity and the benefit of simulation software are acknowledged, especially for complex machining operations with a high number of variants for the tool and process design. After the calculations the results are compared with momentary process design for both gears. However, no software exists at this time capable of providing universal simulation of the entire production process due to missing interfaces and inconsistent data formats. It is a gap that must be closed in the future. The approach for process optimization of gear hobbing begins with starting parametersjust like the process parameters and limitations of the actual process design. Potential limitations may be machine tool parameters such as maximum-revolutions-per-minute for the tool or workpiece spindle, or gear design restrictions like maximum-feedmark deviations. Yet despite these default values and given restrictions, the software calculates every possible tool design capable of achieving these requirements. The design of the gear shaft shows two power gears arranged close together, directly on the shaft; one gear is an interfering element for the manufacture of the other. The tool design is started with the general geometric boundary conditions for the tool. The results are no restrictions concerning the tool outside diameter for Gear No. 2 and a maximum tool outside diameter for Gear No. 1. A
March/April 2013|GEAR TECHNOLOGY
73
technical
geometric calculation leads to a maximum outside diameter for Gear No. 1 of 45mm. The outside diameter for Gear No. 2 can be chosen freely. The calculation is started with momentary process design (Fig. 2red signs). For example, Gear No. 1: It has a hob outside diameter of da=45mm; number of threads z0=1; and number of gashes ni = 9. In the chart the limits for variation are shown. The number of threads were varied from one to three; the hob diameter from 40 to 45 for Gear No. 1, and from 60 to 100 mm for Gear No. 2. The number of gashes is varied from 7 to 19, and 11 to 21. The result revealed by the simulation is that the single-threaded variant is always the most productive. The reasonespecially for Gear No. 1is the lower helix angle for the thread at a lower number of threads. A higher helix angle results in a longer way of entry for the tool. Also, the larger the outside diameter process, the more productive the process. The larger, outside diameter of the single tooth is thicker and therefore more reconditioning cycles can be realized. In general, with the investment for one tool, more workpieces can be produced. As mentioned, the tool outside diameter for Gear No. 1 is limited by Gear No. 2. The maximum-outside-diameter is also limited by the machine tool, as both gears have to be produced in one step, on one machine tool. The number of gashes should be as high as possible from the technological side. A higher number of gashes leads to lower-generated cut deviations. From the productivity aspect a certain number of reconditioning cycles becomes possible, so the single teeth should not be too thin. Especially for Gear No. 1, this tool designwith number of gashes at n i= 11is quite a low number when compared with Gear No. 2, with its number of gashes almost doubled at ni=21. The remaining teeth will be quite thin, with the small outside diameter of da0=45mm. The simulation for Gear No. 1 leads to a tool design similar to the real-time process, so the use and functionality of the actual process design could be proven. In general, the simulation enables a very fast design of the tool by avoiding longlasting iteration cycles. In contrast to only experience-based tool design, the calculation has a robust basis.
Within analysis of secondary machine elements the bearing seats of the gear shaft were investigated. Alternative manufacturing technologies for the finish process of the bearing seats were also evaluated. The technologies had to meet a number of requirements and conditions, including: Material: case-hardened steel 20MnCrS5 Surface hardness: HRA 81-83 Surface roughness: Rz=2 m Concentricity: 0.02mm Circularity: 0.004mm Parallelism: 0.06mm Retain fitting tolerance Retain accuracy grade of cylindrical shaft Right angularity tolerance of contact surfaces Free of damage and pores Economic manufacturing During rough analysis, five manufacturing technologies were identified that are able to manufacture the bearing seats with the necessary requirements (Fig. 4). Because the projects focus was on innovative manufacturing technologies and conventional processes (grinding, hard-turning), a hybrid manufacturing process known as ultrasonic-assisted-
74
[www.geartechnology.com]
turning was considered. In addition, a second process step was considered for manufacture of the surface properties should the first process step prove incapable of meeting all requirements. For this step, hard-roller burnishinga process not yet common to this field was employed. Within rough analysis the manufacturing technologies were assessed considering the impact factors shown in Figure 2. This assessment was conducted by experts from the industry and research institute. The results show that hard-turning and plunge-grinding are the preferred manufacturing processes. As a possible second step, hard-roller burnishing should be used (Fig. 5). To assess the surface quality that can be achieved with the manufacturing technologies discussed here, a Fourier analysis was performed, enabling assessment
of the possible surface roughness of the bearing seats. The advantages and disadvantages of these alternative manufacturing technologies are listed below; results of the surface roughness tests are shown in Figure 6. Hard-turning without ultrasonic support Low ripple Grinding-procedure Higher amplitudes during lower wave numbers Ripple is influenced by self-excited (regeneration effect) and separately excited (imbalances, SLS-radial deviation) oscillations Quickpoint grinding Higher amplitudes than e.c.p. longitudinal grinding are machine-based Higher machine stiffness Lower oscillations than e.c.p. longitudinal grinding
Ultrasonic-assissted turning Low fundamental oscillation Very good concentricity Via rough analysis of manufacturing technologies, two manufacturing chains were chosen for a detailed observation. 1. Plunge-grinding followed by hardroller burnishing: This alternative was chosen because plunge-grinding is a common process that can achieve good results; roller burnishing is an innovative process that can manufacture the required surface properties. Also, these technologies can be combined well. 2. Ultrasonic-assisted turning: To date, this manufacturing technology is rarely used in this field. The surface properties can be achieved without a second step, so it was investigated to determine whether significant time savings can be obtained and if this technology can operate cost-effectively.
March/April 2013|GEAR TECHNOLOGY
75
technical
Within the detailed observation time, costs and the quality of the manufacturing technologies were analyzed by experts that in fact provide these processes. It can therefore be said that in both cases, only one machine tool is needed, as the roller-burnishing tool can be integrated into the grinding machine. There is a lot to be said for both plunge- grinding and roller-burnishing, but their set-up and process-parameter optimization must be done individually. Another advantage of roller-burnishing is the low tool wear and savings in cooling lubricant. The actual process of finishing with abrasive blocks can be substituted. But the main advantage of ultrasonic-assisted turning is that the second finishing step is eliminated. This translates to lower machine investment as the cost for an ultrasonic unit for machine integration is low. But this is a limited experience with this technology and it will require much more effort in process-parameter optimization to lower the process time and attain high production output. It is also unknown at this time which workpiece materials can be manufactured using ultrasonic-assisted turning. Silicon and carbides prevent the use of diamond tools typically required for this process because of their risk of fracture. It is yet to be determined whether a surface roughness far beyond the required properties is needed and justifies the effort in establishing this innovative technology.
Conclusion
In partnering with the Cluster of Excellence, Integrative Production Technology for High-Wage Countries methods were developed to anticipate future requirements of tomorrows markets. Beyond the theoretical research technology conducted, examples were chosen that in fact demonstrated the acquired knowledge. This article examined and presented the results of the technology used in producing the prototype gear shaft. In general, it was possible to create alternative manufacturing chains to manufacture a gear shaft in a more effective and efficient way than is typically done. By using these new manufacturing chains it is possible to manufacture more individual products and reduce planning efforts via simulation methods and the integration of other planning alternatives over defined interfaces. However, a general planning approach was not implemented or tested at this time. Within the investigation, a general look at the process chainas well as a more detailed technological look at a single processwas taken. The investigations were done on an actual gear shaft In summation, the traditional process chain was approved as good. Likewise, the same process design of single-technology-hobbing was approved. The advantages demonstrated by the new methods are the faster and more economical ways to generate a process chain and single-process designs. For the next testing phase, evaluation of three manufacturing chains including logistics and factory planningwould be useful. In this way the exact time and cost potential of a specific manufacturing chain could be determined and an integrated planning approach implemented.
References
1. Brecher, C., G. Hirt, F. Klocke, L. Schapp, R. Schmitt, G. Schuh and W. Schulz. Integrative Production Technology for High-Wage Countries, AWK Aachener Werkzeugmaschinen Kolloquium (Machine Tool Colloquium Aachen), 2008, pp. 1440.
Prof. Dr.-Ing. Dr.-Ing. E.h. Dr. h.c. Fritz Klocke is head of the
chair of manufacturing technology at the Laboratory for Machine Tools and Production Engineering (WZL), a part of RWTH Aachen University, Germany. He is also director of the Fraunhofer Institute for Production Technology in Aachen. is chief engineer for gear technology at the Laboratory for Machine Tools and Production Engineering (WZL). He began his career as a research assistant in 2006 at the chair of machine tools, investigating gear noise behavior with a special emphasis on bevel gears. Since 2011 Brumm has led the gear technology department at RWTH; he was awarded his doctorate in 2011.
was a research associate and doctoral candidate under Prof. Klocke in production engineering at the technology planning group at RWTH Aachen University. His principal research activities are technology planning and investigations on process chain design; he was awarded his doctorate in 2012.
research associate and doctoral candidate under Prof. Klocke in production engineering at the gear technology department at RWTH Aachen University. Since 2010 he has led the group for gear manufacturing. His principal research activities are in gear hobbing and general investigations in process chains for gears.
[www.geartechnology.com]
76
Archeology
www.
Gear Technology is happy to report that every issue (1984 to present) is now available online at
geartechnology
.com.
Need articles on software, gear grinding, plastics, or lubrication? Put away your shovel... Theyre simply a keyword away.
Drop by our website to uncover decades of peer-reviewed technical and back to basic articles You dont need to be an archeologist to excavate the information that matters to you.
www.geartechnology.com/issues.
industry news
lathes and grinders. With these new machines, LMC plans not only to improve its existing capabilities, but also to meet growing demand for products and services including larger products and specialty products. Jay Duerr, LMC Workholding president, said, We have been upgrading machine capabilities, buying new ones to increase capacity, and remodeling parts of the plant and all of our offices. Our goal is to have the best facility in the workholding business to serve the ever changing needs of our growing customer base and the machine tool industry in general. As they continue to drive us into providing more product and services as their business evolves, we must keep pace. We are proud of what weve been able to accomplish in our 97-year history and look forward to getting our customers and prospects here to see everything for themselves. For more information, visit www.lmcworkholding.com.
Klber Lubrication
Appoints Kraemer as CEO
Klber Lubrication, a worldwide manufacturer of specialty lubricants, announces the appointment of Ralf Kraemer as chief executive officer. Kraemer assumes the role of CEO from Dieter A. Becker, who returns to Klbers global headquarters in Munich, Germany, after leading the North American operations for nearly three years. Born in Germany, Kraemer brings more than 15 years of sales, marketing and management experience in the metal cutting, woodworking, industrial equipment and power transmission industries to his new role at Klber. Were excited for the opportunity to have Ralf lead Klber Lubrication North America, said Becker. Klber places particular importance on its industry-leading customer service and in-depth technical and application support. We are committed to providing excellent support to our thousands of customers throughout North America, and Ralf s skills, experience and dedication to a customer service-oriented focus make him the perfect fit to execute this promise. Prior to joining Klber, Kraemer managed operations at a Swiss technology company in the Chicago area and established and developed the North American manufacturing facility and business operations for a German machine tool accessories company near Raleigh, N.C. For the past nine years, he was responsible for the North American operations of a German machine tool company in Pittsburgh, PA. Kraemer holds a degree in industrial engineering and management from the Karlsruhe Institute of Technology and an MBA from the Isenberg School of Management from the University of Massachusetts Amherst.
LMC Workholding
Completes $2 Million Expansion
LMC Workholding recently completed a $2 million expansion at its Logansport, Indiana facility with several new machines, all green lighting, office renovations and other plant improvements. The new machines include an expandable six-pallet horizontal machining center, several vertical machining centers,
78
[www.geartechnology.com]
Somaschini
SDP
ISO 9001 R E G I S T E R E D
REGISTERED
ISO 9001 AS 9100
SI
motorcycle, marine, textile machines, machine tools, robotics, railway and renewable energy. In 2007, Somaschini established Somaschini Automotive S.r.l. in a satellite facility located in Entratico (Bergamo), Italy to bring all high-volume automotive production into a dedicated plant. Today, the Somaschini Group has 250 employees and sales of 50 million Euro.
Are you sitting on an idea for a technical paper but wondering where to present it? Do you have one already written, sitting on your desk, gathering machine dust? How about Gear Technology? We are always looking for gearing- and power transmission component-relevant technical papers for publication in the magazine and in its digital version. Having your work appear in Gear Technology guarantees you an audience of the most experienced and discriminating industry players. You say your work has not been peer-reviewed? Not a problem, as we are luckyand thankfulto have on-hand some of the most experienced and brilliant minds in the industryour technical editors. So if your work passes muster and is published, youll know you were reviewed by the bestand most demanding. Chances are youll be creating the paper under the auspices of the company for whom you work or own, or for one of the various industry-relevant associations. That means they as well will bask in the reflected glory that accrues with publication in Gear TechnologyThe Journal of Gear Manufacturing. For publication guidelines and more information, please contact Jack McGuinn at jmcguinn@geartechnology.com.
1/2/13 12:05 PM
79
industry news
Dwight Smith
GLEASON
www.gearmachineryexchange.com
Lift&Drop Cams, Genevas for MODELS
13" (330mm), 3.4 DP (7.5 Module), Excellent, Pinions, Ring Gears, Helical Motion, Formate, Extented Tilt, 1982
Model 642
Star SU
INDEX PLATES
GLEASON
www.gearmachineryexchange.com
80
GEAR TECHNOLOGY|March/April 2013
Generators
605-610
degree (Unimep), and a mechanical engineering degree (EEP). He is fluent in English, Spanish and Portuguese. Chris Cella has been appointed application engineer at Star SU, LLC. In his new role, Cella will provide additional depth to the application engineering department, with a focus on continually improving customer technical support and tool design services. Cella brings two decades of experience in the fields of round tools, gundrills and gundrilling to his new position. He has spent the last decade providing tool reconditioning services, continuous improvement programs and troubleshooting support in the aerospace, automotive, heavy truck, hydraulic, power generation and transportation industries. He holds a bachelors degree in mechanical engineering from the University of Illinois at Chicago.
S p e c i a l i S T S
cgearinc.com
New Capabilities
Hofler Model 800 CNC Single Tooth Gear Grinder 31 x 60 long with internal grinding capabilities Klingelnberg P-100 Gear Inspection Machine 40 Dia. Maximum
www.suhner.com
March/April 2013|GEAR TECHNOLOGY
81
industry news
Applied Process
Hosts First AP University
More than 30 designers and engineers went back to college to learn how austempered ductile iron (ADI) could work in their manufacturing operations. The first ever AP University, hosted by Applied Process, Inc., was held in January at Eastern Michigan University on the Livonia Campus and Joyworks Studio in Ann Arbor, Michigan. The program was so successful that plans are in the works for another session. The three-day event was created to educate those who design engineered components on how to best utilize the opportunities provided by ductile iron and ADI. Curriculum covered a range of topics and was taught by industry professionals. Classes covered the casting process, castability studies, casting issues and resolutions, successful weldment to casting conversions, an introduction to ADI, Austempering 101, ADI applications in gearing and applications of casting conversions. Attendees toured the Applied Process plant and visited Joyworks, a metalworking studio focused on research and education owned by John R. Keough, chairman of Applied Process. The event was much more than expected, explained Tim Covert, senior material engineer at Ford Motor Company. We deal with ADI, but I was new to casting design. I was impressed, not only by the process, but by the knowledge and professionalism shown by the Applied Process staff. Austempering is an isothermal heat treatment that produces a structure that is stronger than those created by conventional heat treatments. Austempered ductile iron (ADI) is a specialty heat-treated material that creates a lighter, stronger, quieter and more wear resistant part. Bill Maenle, engineer and product design at Unverferth Mfg., has dealt with ADI in the past. Moving from welding to casting has allowed us more flexibility, which means we can best cater to the needs of specific soil conditions. In my experience, ADI provides a better product with more reliability. Many attendees who were new to ductile iron, more specifically ADI, left AP University with a knowledge base that will allow them to convert and improve current and future projects. I am a chemist by degree and knew little about heat treatments and metals three days ago, admitted Michael Schmidt, business manager at Pennsy. As we move into metals I am confident we will find applications for ADI.
A versatile tackle box has many solutions. When MTB tackles the recontrol of your equipment, a complete electrical cabinet replacement takes place. All servomotor power and feedback cabling, as well as the encoder cabling, are replaced. This almost plug-and-play scenario offers you the versatility to keep the machine in production until the controls kit is ready. Four weeks later, your machine has versatile functionality.
82
[www.geartechnology.com]
The Worlds Largest Automotive TM & Drives Event More Than 1,600 Senior Attendees In Europe, USA & China In 2012!
7th International
Which technologies contribute the most to obtain best fuel efciency? Which will be the most successful technically & commercially?
Basics and practice of automotive transmissions specially tailored to those who want to refresh their knowledge or start working in this business eld
26 companies showing new products and developments. New companies joining the exhibition!
PLUS
PLUS
Sponsors
www.transmission-symposium.com/pte
calendar
April 812Hannover Messe 2013. Hannover
Fairgrounds, Hannover, Germany. The worlds leading trade show for industrial technology returns in 2013 with a full lineup of trade shows under the banner Integrated Industry. The 11 co-located shows include Industrial Automation; Motion, Drive and Automation; Energy; Wind; MobiliTec; Digital Factory; ComVac; Industrial Supply; Surface Technology; IndustrialGreen Tec and Research and Technology. Russia is the official partner country in 2013. Discover new perspectives on energy, automation and industrial supply and engineering topics as well as a broad range of events and displays affecting the global industrial market today. Other Hannover highlights include Metropolitan Solutions, TectoYou, Job and Career Market and Energy Efficiency in Industrial Processes. For more information, visit www.hannovermesse.de. MLB pitcher Jim Abbott will also give a presentation on overcoming adversity. Theres also a scheduled visit to the United States Marine Corps Air Station in Miramar and a night of entertainment celebrating the iconic music of the 1960s. The event includes general sessions, presentations, receptions and the AGMA/ABMA Golf Tournament taking place at the Park Hyatt Aviara Golf Course. For more information, visit www.agma.org.
is a contract manufacturing expo for all job shops and contract manufacturers that provides custom metal, plastic, rubber or electronic parts and related manufacturing services to OEMs. Attendees include top level purchasing, engineering and production managers who are directly involved in buying custom contract manufacturing services. Representatives from companies of all sizes attend from a range of industries, often with blueprints in hand. The AmCon shows occur regionally throughout the year. Past attendees include ABB, General Electric, Honeywell, Johnson Controls, Parker Hannifin, Rockwell Automation, SaintGobain, Siemens and more. For more information, visit www. amconshows.com.
April 910AmCon Design and Contract Manufacturing Expo 2013. Seattle, Washington. AmCon
Laboratory. The Ohio State University, Columbus, Ohio. For more than 33 years, this course has been offered as a tool to engineers and technicians involved in the analysis, manufacture, design, specification or utilization of simple and complex gear systems. Industries that find this course helpful include the automotive, transportation, wind-energy, process machinery, aircraft, appliance, general manufacturing and all gear manufacturers. The course material is covered in such a way that the fundamentals of gearing, gear dynamics, noise analysis and measurements are covered. This makes the course appropriate to the gear designer with little knowledge of noise analysis, as well as to the noise specialist with little prior knowledge of gears. Course attendees are asked to present a brief synopsis of problems they have encountered or of a procedure they have used for gear noise analysis and reduction. Possible approaches to solve each problem are discussed. For more information, visit www.gearlab.org.
April 29May 2Gear Dynamics and Gear Noise Short Course. Gear Dynamics and Gear Noise Research
Cutting Tools Gear School, Loves Park, Illinois. This comprehensive three-and-a-half-day program is a blend of shop time and classroom study. A coordinated series of lectures is presented by engineering, production, inspection and sales staff members. It is recommended for those seeking to understand the fundamentals of gear geometry, nomenclature, manufacturing and inspection. Training groups are kept small so that individual concerns may be fully addressed. Shop tours and demonstrations are conducted to visually enhance the understanding of classroom discussions. The fee of $895 includes handbook and all materials, one group dinner and all lunches. For more information, visit www.gleason.com. Technologies Inc. hosts an all-day workshop to provide attendees with an overview of IntensiQuench (IQ) processes, examine the data from actual part studies, and give attendees a forum to discuss the application of intensive quenching to enhance the performance properties of their heat treated products. The workshop will help answer questions such as: How can my heattreated products benefit from intensive water quenching and save costs? How does the IQ process provide both enhanced strength and better ductility at the same time? How does intensive quenching equipment differ from traditional water, oil, salt or gas quenching systems? Manufacturing engineers, experienced heat treat metallurgists, steel product design engineers should attend this workshop. For more information, visit www. intensivequench.com.
May 22May 23AGMA Marketing and Forecasting Conference 2013.Crowne Plaza, Chicago
April 2527AGMA/ABMA Annual Meeting. Park Hyatt Aviara, Carlsbad, California. Featured presenters include Jay Timmons (National Association of Manufacturers), Jim Meil (Eaton Corporation) and Dan Campion (Solar Turbines). Former
OHare Hotel and Conference Center, Rosemont, Illinois. Whats going on in the gear market? What is happening in the end user market that will affect next year? How can you better prepare your company for the ups and downs of the current economic climate? The Marketing and Forecasting Conference will present a comprehensive report on the U.S. Economic Conditions, Industry Conditions for Gears, Gear Market Bookings and Gear Market Shipments. This will be broken down into a series of end user markets including total gears, industrial machinery gears, construction machinery gears, farm machinery gears, power transmission equipment, mining, ship and offshore, railroad and aerospace gears. IHS Global Insight has developed news reports that will forecast these various markets. This AGMA memberonly event includes a reception and dinner for networking opportunities. For more information, visit www.agma.org.
84
[www.geartechnology.com]
The complete set of back issues of Gear Technology is available online--but ONLY if you're a subscriber. Make sure you have access by filling out the form!
2 3
City:
SAVE a TREE!
Please update your contact information or attach you business cards here. (No Staples)
DIGITAL SUBSCRIPTIONS
C orporate Executive (B) M anufacturing Production Management (C) M anufacturing Production Department (D) M anufacturing Engineering Management (E) M anufacturing Engineering Department (F) P roduct Design, R&D Management (H) P roduct Design, R&D Department (I)
YES, I would like to receive Gear Technologys YES, I would like to receive Gear Technologys
monthly e-mail Product Alerts
How are YOU involved with gears (check all that apply)?
My company MAKES gears (20) My company BUYS gears (22) I DESIGN gears (23) I am a SUPPLIER to the GEAR INDUSTRY
(please specify product or service) (24)
YES, I would like to receive subscription renewal No, I do not wish to be contacted by e-mail. FAX TO 1-847-437-6618 or
VISIT US ONLINE AT
www.geartechnology.com/subscribe.htm
ad index
A uniquely global publication focusing on on peening, blasting, cleaning and vibratory finishing!
Vol. 12 September Issue Year 2011
Publication for the Peening, Blasting, Cleaning and Vibratory Finishing Industries
A.G. Davis/AA Gage page 15 www.agdavis.com AGMA page 57 www.agma.org ALD Thermal Treatment page 27 www.aldtt.net ALD-Holcroft page 23 www.ald-holcroft.com All Metals & Forge Group, LLC page 26 www.steelforge.com
Ipsen International page 43 www.ipsenusa.com Kapp Technologies page 3 www.kapp-usa.com Klingelnberg Outside Back Cover www.klingelnberg.com Liebherr page 5 www.liebherr.com Machine Tool Builders Inc. page 82 www.machinetoolbuilders.com Martin Tool & Forge page 22 www.martintools.com
th n for catio g, Publi astin ing, Bl and Peen ning Clea ing Finish tory ra ies Vib Industr
blica tion fo Peen ing, Bl r the astin g, Clea ning Vibra and tory Finish ing Industr ies
B&R Machine & Gear Corp. Inside Back Cover McInnes Rolled Rings page 28 www.mcinnesrolledrings.com www.brgear.com Beavermatic page 37 www.beavermatic.com Brevini Wind page 7 www.breviniwind.com Metal Finishing News page 86 www.mfn.li Midwest Gear & Tool Inc. page 80 midwestgear@sbcglobal.net
MFN is
www.parts2clean.com
FN is
an.com parts2clean
l Officia is the xpo - MFN po.de of PaintE aintex ion www.p r in Educat Partne
ning Clea -27) 6 www.paintexpo.de - MFN is the Official r the Partner in Education of ns fo ns (p. 2 oPaintExpo Soluti guratio g in Con last ed B rkpiece o omiz Cust mplex W Nadcap COLUMN: of Co
What has the Nadcap Supplier Support Committee done for me?
www.p Partne aintexpo.de r in Edu - MF cation N is the Off of Pai ntExpo icial
The Broach Masters & Universal Gear page 19 Mitsubishi Heavy Industries page 8 www.mitsubishigearcenter.com www.broachmasters.com Chevin Tools page 4 www.chevintools.com Comtorgage page 20 www.comtorgage.com CTICar Training Institute page 83 www.transmission-symposium.com/pte Custom Gear & Machine page 81 www.cgearinc.com
sses in Se rvice (p. 10
page 61
MN:
11 th MF Shot N As Pe Trade ening Wo ian rks Sh 31 st Oc ow in Sin hop & ga t.-3 rd Nov. pore (see page 2011 23)
Mitsubishi Materials page 82 www.mmus.com Mitutoyo page 16 www.mitutoyo.com Overton Chicago Gear page 87 www.oc-gear.com Presrite Corp. page 17 www.presrite.com Process Equipment page 50 www.gearinspection.com PTG Holroyd page 32 www.holroyd.com Schafer Gear Works page 33 www.schafergear.com Schnyder S.A. page 4 www.hanikcorp.com Seco Tools page 35 www.secotools.com/us Sicmat page 31 www.star-su.com Star SU LLC pages IFC1, 31, 87 www.star-su.com Solar Atmospheres page 21 www.solaratm.com Stock Drive Products/Sterling Instrument page 79 www.sdp-si.com/plastic Suhner Manufacturing page 81 www.suhner.com VDIDrivetrain for Vehicles Congress page 41 www.transmission-congress.eu Zoller page 54 www.zoller-usa.com
page
57
11th MFN Asian Shot Peening Workshop & Trade Show in Singapore 31st Oct.-3rd Nov. 2011 (see page 12)
Expo Paint
MFN-J red by Pa intEx OT po Works Industrial 17 th of hop in Ge Painting rm Nove mber, any 2011
Spon so
Nadc
Sponsored by PaintExpo
MFN-JOT Industrial Painting Workshop in Germany 17th of November, 2011
ian N As p& th 11 MF Worksho re po ing Peen Singa 11 Shot Show in 20 rd Nov. Trade t.-3 ) st 31 Oc e page 29 (se
www.mfn.li
www Than esidu50 years (p. 10-11) .mfn MoreR al Str .li e
page
ap CO
DTR Corp. page 51 www.dragon.co.kr Forest City Gear page 46 www.forestcitygear.com Gear Consulting Group page 87 www.gearconsultinggroup.com The Gear Machinery Exchange page 80, 87 www.gearmachineryexchange.com The Gear WorksSeattle, Inc. page 87 www.thegearworks.com Gleason Corp. pages 44-45 www.gleason.com GMTAGerman Machine Tools of America page 65 www.gmtamerica.com Goldstein Gear Machinery LLC page 80, 87 www.goldsteingearmachinery.com Hans-Jrgen Geiger Maschinen-Vertrieb page 49 www.geiger-germany.com Index Technologies page 87 www.gallenco.com Inductoheat page 10 www.inductoheat.com
MFN (Metal Finishing News) is distributed in 67 countries and published 6 times a year.
www.mfn.li
MFN offers courses for:
Training in 9 languages!
MFN is a Partner in Education in Nadcap
MFN is an Official Collaboration Partner of FEMS
86
[www.geartechnology.com]
classified
DAY CLASS to cover the practical aspects of gear technology and geometry aiming toward a logical approach to trouble shooting and optimizing the manufacturing processes
Trouble shooting the process from inspection data. Cutter wear and failure analysis. Cutter materials and coatings. Optimization of feeds and speeds. Hob shifting procedures and optimization. Use of standards. Open forum on attendees experienced problems.
QR-Code Generator
ID KAYWA READER FEED2MOBILE DATAMATRIX GENERATOR NEW: DOKODARE PHOTO LENDORFF KAYWA
Gear geometry and its relationship to gear generation. Gear inspection procedures and analysis. Understanding the processes of Hobbing, Shaping and Shaving.
htt
June 19, 20 & 21, 2013 / Addison, IL More information Contact Bobbie ph: 904-392-0907 Overton Chicago Gear www.gearconsultinggroup.com gearconsulting@aol.com
<img src="http://qrcode.kaywa.com/img.php?s=12&d=http%3A%2F%2Fww
QR-CODE GENERATOR
Content type: URL Text Phone Number SMS
Content: URL:
http://www.gearconsultinggroup.com
Size: XL
Generate!
1 of 2
WANTED:
Model 14 Straight Bevel Model 24A Straight Bevel Models 175, 250, 275, 600 and 1000 Hypoid Cutters Models 200, 275, 400/450, 600 and 800 G or GP Hypoid Grinders RSR and TRI AC Cutter Setup Stand Model 562 Blade Inspection Device Model 563 Cutter Inspection Device
GLEASON
www.gearmachineryexchange.com
87
back to basics
Lead
Lead piece (in blue). As can be seen from the Lead figure, the relative motions of the cutting tool and workpiece are what allow Pitch a straight-sided toolthe hobto generDiameter ate an involute curve. Pitch During this rotation, the hob is typiPitch Diameter cally fed axially with all the teeth being Diameter gradually formed as the tool traverses the work face (Fig. 1b). The hob itself is basically a worm with gashes cut across it to produce the cutting edges (Fig. 2a). Each cutting tooth Figure 2a The hob is basically a worm with is also relieved radially to provide chip gashes cut across it to produce the cutting edges. clearance behind the cutting edge (Fig. Relief 2b). This also allows the hob face to be Relief Relief sharpened and still maintain the original Tooth Face Tooth Face Tooth Face tooth shape. In its simplest form, the hob tooth takes on the shape of a straightsided rack tooth (Fig. 2c). The final proGash Gash Gash file of the tooth is created by a number of flats blending together. The number of flats corresponds to the number of cutting gashes which pass the workpiece tooth during a single rotation. Thus, the greater the number of gashes in the hob, Figure 2b This side view of a hob shows how each cutting tooth is relieved the greater the number of flats along the radially to provide chip clearance Pressure Angle profile, which improves the smoothbehind the cutting edge. Pressure Angle ness of the tooth profile. Pressure Angle
Cutting Cutting Depth
Depth
Cutting Depth
Figure 2c In its simplest form, the hob tooth takes on the shape of a straightsided rack tooth.
hob basics
at www.geartechnology.com
Figure 1b Hob and workpiece each rotate during the hobbing process. For a spur gear being cut with a single-start hob, the workpiece will advance one tooth for each revolution of the cutter.
The material in this Back-to-Basics Brief was adapted primarily from The Gear Hobbing Process, by Dennis Gimpert, which appeared in the January/February 1994 issue of Gear Technology . The original article goes into much greater detail about cutter modifications, hobbing machine mechanics, different hob feed approaches, multi-start hobs and hob thread-spacing errors.
88
[www.geartechnology.com]
BIG GEARS
IN-HOUSE STEEL MATERIAL WAREHOUSE STRAIGHT BEVEL GEARS: 80"PD
SPIRAL BEVEL GEARS: 66"PD
FULL HEAT TREATING SERVICES SPURS, HELICALS, SPLINE SHAFTS GEARBOX REPAIR/REBUILDS EDM WIRE BURNING
REVERSE ENGINEERING BREAKDOWN SERVICES
TOLL FREE: 8002380651
inquiry@brgear.com
www.brgear.com
TEAMPLAYER.
GEAR MANUFACTURING SOLUTIONS FOR MAXIMUM PERFORMANCE BY KLINGELNBERG
OERLIKON
BEVEL GEAR TECHNOLOGY
HFLER
CYLINDRICAL GEAR TECHNOLOGY
KLINGELNBERG
MEASURING CENTERS
A winning team has a system. It is perfectly tuned and balanced. It acts with the utmost precision. The strengths of each individual work together like perfect gears. Klingelnbergs divisions are true team players: Ground breaking solutions for an optimal production process of Bevel and Cylindrical Gears give manufacturers worldwide a leading edge in gear manufacturing. NEXT FAIR: Win the match: www.klingelnberg.com www.ho er.com KLINGELNBERG America, Inc.
p. +1 734 470 6278 e. usa.sales@klingelnberg.com
Hall E2 Booth E2-805 April 22-27, 2013 Beijing, China
SUBJECT TO CHANGES.
MEASURING CENTERS