Toshiba Personal Computer Libretto 100CT

File No.
960-140
1 Toshiba Personal Computer
Copyright
1998 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba Libretto 100CT Maintenance Manual First edition February 1998 Disclaimer The information contained in this manual is subject to change without notice. Toshiba Corporation and Toshiba America Information Systems, Inc., assume no liability for damages incurred directly or indirectly from errors, omissions, or discrepancies in connection with the furnishing, performance, or use of this material. Trademarks IBM is a registered trademark, and PC/AT, PS/2 and OS/2 are trademarks of IBM Corporation. MS-DOS and Windows are registered trademarks of Microsoft Corporation. Intel and Pentium are registered trademarks, and MMX is a trademark of Intel Corporation. Lotus is a registered trademark of Lotus Development Corporation. Novell and NetWare are registered trademarks of Novell, Inc. UNIX is a registered trademark of X/Open Company Ltd. Sound Blaster and Pro are trademarks of Creative Technology Ltd. Centronics is a registered trademark of Centronics Data Computer Corporation. All other properties are trademarks or registered trademarks of their respective holders.
ii
File No. 960-140
Preface
This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Libretto 100CT. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field.
SAFETY PRECAUTIONS
Four types of messages are used in this manual to bring important information to your attention. Each of these messages will be italicized and identified as shown below. DANGER: Danger indicates the existence of a hazard that could result in death or serious injury if the safety instruction is not observed.
WARNING: Warning indicates the existence of a hazard that could result in bodily injury if the safety instruction is not observed.
CAUTION: Caution indicates the existence of a hazard that could result in property damage if the safety instruction is not observed.
NOTE: A Note contains general information that relates to your safe maintenance services. Improper repair of the computer may result in safety hazards. Toshiba requires service technicians and authorized dealers or service providers to ensure the following safety precautions are adhered to strictly. Be sure to fasten screws securely with the right screwdriver. If a screw is not fully fastened, it could loosen and create a short circuit, which could cause overheating, smoke, or fire. If you replace the battery pack, RTC battery, or backup battery, be sure to use only the same model battery or an equivalent battery recommended by Toshiba. Installation of the wrong battery can cause the battery to explode.
iii
File No. 960-140
The manual is divided into the following parts: Chapter 1 Chapter 2 Chapter 3 Chapter 4 Appendices Hardware Overview describes the system unit and each FRU. Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Tests and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Replacement Procedures describes the removal and replacement of the FRUs. The eight appendices describe the following: Handling the LCD module Board layout Pin assignments Keyboard scan/character codes Key layout Wiring diagrams BIOS Rewrite Procedures Reliability
iv
File No. 960-140
Conventions
This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification, acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations. The keytop symbol, as it appears on the keyboard, is printed in boldface type. Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the keytop symbols separated by a plus (+) sign. For example,Ctrl + Pause (Break) means you must hold down Ctrl and at the same time press Pause (Break). If three keys are used, hold down the first two and at the same time press the third. User input Text that you are instructed to type in is shown in the boldface type below: DISKCOPY A: B: The display Text generated by the computer that appears on its display is presented in the typeface below: Format complete System transferred
File No. 960-140
Table of Contents
Chapter 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 Hardware Overview
Features..................................................................................................................1-1 System Unit Block Diagram....................................................................................1-5 3.5-inch External FDD............................................................................................1-9 2.5-inch Hard Disk Drive......................................................................................1-10 Keyboard..............................................................................................................1-11 TFT Color LCD....................................................................................................1-12 Power Supply .......................................................................................................1-14 Batteries ...............................................................................................................1-16 Troubleshooting Procedures
Chapter 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9
Troubleshooting......................................................................................................2-1 Troubleshooting Flowchart.....................................................................................2-2 Power Supply Troubleshooting...............................................................................2-6 System Board Troubleshooting.............................................................................2-14 FDD Troubleshooting...........................................................................................2-25 HDD Troubleshooting ..........................................................................................2-28 Keyboard Troubleshooting....................................................................................2-34 Pointing Device Troubleshooting..........................................................................2-36 Display Troubleshooting.......................................................................................2-37 Tests and Diagnostics
Chapter 3 3.1 3.2 3.3 3.4 3.5 3.6
The Diagnostic Test................................................................................................3-1 Executing the Diagnostic Test.................................................................................3-3 Subtest Names........................................................................................................3-7 System Test............................................................................................................3-9 Memory Test ........................................................................................................3-10 Keyboard Test ......................................................................................................3-12
vi
File No. 960-140 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22 3.23 3.24 Display Test..........................................................................................................3-16 Floppy Disk Test ..................................................................................................3-20 Printer Test...........................................................................................................3-22 Async Test............................................................................................................3-24 Hard Disk Test .....................................................................................................3-26 Real Timer Test....................................................................................................3-30 NDP Test .............................................................................................................3-32 Expansion Test .....................................................................................................3-33 Sound Test ...........................................................................................................3-35 Error Code and Error Status Names......................................................................3-36 Hard Disk Test Detail Status.................................................................................3-39 Hard Disk Format.................................................................................................3-41 Head Cleaning ......................................................................................................3-46 Log Utilities..........................................................................................................3-47 Running Test ........................................................................................................3-49 Floppy Disk Drive Utilities....................................................................................3-51 System Configuration............................................................................................3-56 SETUP.................................................................................................................3-58 Replacement Procedures
Chapter 4 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12
Overview................................................................................................................4-1 HDD.......................................................................................................................4-8 Optional Memory Module.....................................................................................4-10 Keyboard..............................................................................................................4-12 Display Assembly..................................................................................................4-13 RTC Battery.........................................................................................................4-17 System Board, Heat Sink and PC Card Slot..........................................................4-18 Display Mask........................................................................................................4-20 FL Inverter Board.................................................................................................4-22 LCD Module ........................................................................................................4-24 Speaker, Power Switch Board and AccuPoint Board.............................................4-27 LCD Flexible Cable and Microphone.....................................................................4-30
vii
File No. 960-140 4.13 I/O Adapter Board................................................................................................4-35
Appendices Appendix A Appendix B Appendix C Appendix D Appendix E Appendix F Appendix G Appendix H Handling the LCD Module ......................................................................... A-1 Board Layout.............................................................................................B-1 Pin Assignments......................................................................................... C-1 Keyboard Scan/Character Codes ................................................................D-1 Key Layout ................................................................................................ E-1 Wiring Diagrams .........................................................................................F-1 BIOS Rewrite Procedures ..........................................................................G-1 Reliability...................................................................................................H-1
viii
File No. 960-140
Chapter 1 Hardware Overview
File No. 960-140
1-ii
File No. 960-140
Chapter 1
1.1 1.2 1.3 1.4 1.5 1.6
Contents
Features..................................................................................................................1-1 System Unit Block Diagram....................................................................................1-5 3.5-inch External FDD............................................................................................1-9 2.5-inch Hard Disk Drive......................................................................................1-10 Keyboard..............................................................................................................1-11 TFT Color LCD....................................................................................................1-12 1.6.1 1.6.2 TFT Color LCD Module..................................................................1-12 FL Inverter Board ............................................................................1-13
1.7 1.8
Power Supply .......................................................................................................1-14 Batteries ...............................................................................................................1-16 1.8.1 1.8.2 1.8.3 1.8.4 Main Battery....................................................................................1-16 Battery Icon.....................................................................................1-16 Battery Charging Control.................................................................1-17 RTC Battery ....................................................................................1-17
Figures Figure 1-1 Front of the computer........................................................................................1-4 Figure 1-2 System unit configuration..................................................................................1-4 Figure 1-3 System unit block diagram.................................................................................1-5 Figure 1-4 3.5-inch FDD ...................................................................................................1-9 Figure 1-5 2.5-inch HDD.................................................................................................1-10 Figure 1-6 Keyboard .......................................................................................................1-11 Figure 1-7 TFT color LCD..............................................................................................1-12
1-iii
File No. 960-140
Tables Table 1-1 3.5-inch FDD specifications...............................................................................1-9 Table 1-2 2.5-inch HDD specifications..............................................................................1-9 Table 1-3 LCD specifications...........................................................................................1-12 Table 1-4 FL inverter board specifications.......................................................................1-13 Table 1-5 Power supply board output rating....................................................................1-15 Table 1-6 Battery specifications........................................................................................1-16 Table 1-7 Time required for quick charges........................................................................1-17 Table 1-8 RTC battery charging/data preservation time...................................................1-17
1-iv
File No. 960-140

1 Features
1.1
Features
The computer uses Toshiba's advanced Large Scale Integration (LSI ), and Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage and high reliability. This computer incorporates the following features and benefits: Microprocessor The computer is equipped with an Intel Pentium processor with MMX Technology that operates at 166MHz and 1.8/2.5 volts. Memory The computer comes with 32MB of Extend Data Out (EDO) DRAM. HDD The computer has a 2.5-inch HDD with a capacity of 2.1GB HDD or 3.2GB HDD. Display The computer has a 7.1-inch color, Thin Film Transistor (TFT) Liquid Crystal Display (LCD), that enables display up to 256K colors at a resolution 800 x 480 pixels. A video controller and 2MB of VRAM enable an external monitor to display 16M colors at a resolution of 800 x 600 pixels or 64K colors at a resolution of 1024 x 768 pixels. Keyboard An-easy-to-use 80/82-key keyboard provides a numeric keypad overlay for fast numeric data entry or for cursor and page control. The keyboard also includes two keys that have special functions in Microsoft Windows 95. It supports software that uses a 101- or 102-key enhanced keyboard. Batteries The computer has two batteries a Lithium-Ion main battery pack and RTC battery that backs up the Real Time Clock and CMOS memory. Expansion memory slot An optional 32MB memory module can be installed in the memory slot.
1-1
File No. 960-140 Universal Serial Bus (USB) The USB enables daisy-chain connection of up to 127 USB-equipped devices and 12Mbps serial data transfer. It is designed for easy configuration by a PnP operating system and provides hot insertion/ejection capability. The USB port is only on the Enhanced Port Replicator. External monitor port The port is available only on the I/O adapter and enables connection of an external SVGA compatible monitor. PC card slot A PC card slot accommodates two 5mm cards (Type II) or one 10.5mm (Type III) card, which support the PC card Standard. These slots support an external FDD, 16-bit PC cards and CardBus PC cards (32 bit) as well as the Zoomed Video (ZV) port cards, which are dedicated to high-performance video data transfer such as MPEG video play back. AccuPoint This pointer control stick, located in the right of the display panel, provides convenient control of the cursor without requiring desk space for a mouse. Docking interface A 140-pin, docking interface port enables connection of the I/O adapter or an optional Enhanced Port Replicator. The Enhanced Port Replicator has two additional PC card slots that one accommodates a 10.5mm card (Type III) and one accommodates a 5mm card (Type II). These slots support CardBus PC card. The Enhanced Port Replicator also has PS/2 mouse, PS/2 compatible keyboard, USB, parallel, serial and external monitor ports. Infrared port The infrared port is compatible with Fast InfraRed (FIR) standards enabling wireless 4Mbps data transfer with Infrared Data Association (IrDA) 1.1 compatible devices. Sound system A Sound Blaster Pro and Windows Sound System compatible sound system gives the computer multimedia capability. The sound system is equipped with speaker, microphone and stereo headphone jack.
1-2
File No. 960-140 External FDD A 3.5-inch external FDD is connected to the PC card slot and accommodates both 2HD (1.44MB) and 2DD (720KB) disks.
1-3
File No. 960-140 The computer is shown in Figure 1-1. The system unit configuration is shown in Figure 12.
Figure 1-1 Front of the computer
Figure 1-2 System unit configuration
1-4
File No. 960-140
1.2
System Unit Block Diagram
Figure 1-3 is a block diagram of the system unit.
Figure 1-3 System unit block diagram
1-5
File No. 960-140 The system unit is composed of the following major components: Intel Pentium processor Intel 166MHz Pentium processor with MMX Technology. The math co-processor and 32KB cache memory are integrated into the Pentium. Standard RAM 32 MB, four 4M x 16-bit EDO DRAM chips 3.3 volt operation No parity bit Access time 60 ns Data transfer is 64-bit width
BIOS ROM (Flash EEPROM) 512 KB, one 512K x 8-bit chip 256 KB are used for system BIOS 64 KB are used for VGA-BIOS 8 KB are used for plug and play data area 8 KB are used for password security 16 KB are used for boot strap 288 KB are reserved 5 volt operation Access time 120 ns Data transfer is 8-bit width
Optional memory One expansion memory slot is available for 32MB memory modules. The 32MB memory modules consist of four 4M x 16-bit EDO DRAM chips. 3.3 volt operation No parity bit Access time 60 ns Data transfer is 64-bit width
1-6
File No. 960-140 System Controller Gate Array This gate array has the following functions: CPU interface/control DRAM control PCI master/slave interface Write buffer (CPU-DRAM, CPU-PCI, PCI-DRAM) Prefetch buffer (CPU-PCI, PCI-DRAM) Mobile-PC/PCI support DMA function Serial interrupt function Power management control Suspend/resume control CPU stop clock function PCI clock stop function ACPI support function
I/O & PC Card Controller Gate Array This gate array has the following functions: One UARTs 16550A equivalent (One SIO is used for SIR.) One parallel port control supported ECP mini ISA bus control PCI bus front end control PC card control ZV-port support CardBus control FIR function Universal I/O port Beep volume Speaker control RTC One T9934 chip is used
Video Controller The NeoMagic NM2160 chip is used. The Video controller incorporates 2MB of video memory using a 128-bit data path.
Keyboard Controller (KBC) One M38813S chip is used. This KBC includes the keyboard scan controller and keyboard interface controller. The KBC controls the internal keyboard, external keyboard, AccuPoint and PS/2 mouse.
AccuPoint Controller (IPSC) One EMEP 010B chip is used. This controller provides simultaneous control of the Pointing Device.
1-7
File No. 960-140 Sound Controller One OPL3-SA3 is used. The OPL3-SA3 incorporates OPL3 FM synthesizer, Digital Analog Converter (DAC) and MPU401 MIDI interface.
1-8
File No. 960-140
1.3
3.5-inch External FDD
The 3.5inch external FDD is a thin, high performance reliable drive that supports 720KB (formatted) 2DD and 1.44MB (formatted) 2HD disks. The FDD can be connected to the PC card slot.
The FDD is shown in Figure 1-4. The specifications for the FDD are listed in Table 1-1.
Figure 1-4 3.5-inch FDD Table 1-1 3.5-inch FDD specifications

Item Storage capacity (KB) Unformatted Formatted Number of heads Number of cylinders Access time (ms) Track to track Average Head settling time Recording track density (tpi) Data transfer rate (Kbps) Rotation speed (rpm) Recording method 2-MB mode 2,000 1,440 2 80 3 181 15 135 500 300 1-MB mode 1,000 720 2 80 3 181 15 135 250 300
Modified Frequency Modulation (MFM)
1-9
File No. 960-140
1.4
2.5-inch Hard Disk Drive
The removable HDD is a random access non-volatile storage device. It has a nonremovable 2.5-inch magnetic disk and mini-Winchester type magnetic heads. The computer supports 2.1GB HDD or 3.2GB HDD. The HDD is shown in Figure 1-5. Specifications are listed in Table 1-2.
Figure 1-5 2.5-inch HDD Table 1-2 2.5-inch HDD specifications

Items Formatted capacity (bytes) Logical cylinders Logical heads Logical sectors Bytes per sector Rotation speed (rpm) Recording method IBM DYKA-22160 2,167,603,200 4,200 16 63 512 4,200 8-9 RLL IBM DYKA-23240 3,253,469,184 6,304 16 63 512 4,200 8-9 RLL
1-10
File No. 960-140
1.5
Keyboard
The 84-(USA) or 86-(European) key keyboard is mounted on the system unit. The keyboard is connected to the keyboard controller on the system board through a 24-pin flat cable. The keyboard is shown in Figure 1-6. See Appendix E for optional keyboard configurations.
Figure 1-6 Keyboard
1-11
File No. 960-140
1.6
TFT Color LCD
The display panel contains a TFT color LCD module, a fluorescent lamp (FL) andan FL inverter board. 1.6.1 TFT Color LCD Module The LCD enables display of up to 256K colors at a resolution 800 x 480 pixels. The LCD is shown in Figure 1-7. Specifications are listed in Table 1-3.
Figure 1-7 TFT color LCD Table 1-3 LCD specifications

Items Number of Pixels Dot pitch (mm) (mm) (pixels) Specifications 800x480 0.192x0.192 153.6(H)x92.16(V) 1:150 (Typ)
Display area Contrast
1-12
File No. 960-140
1.6.2 FL Inverter Board The FL inverter board supplies high frequency current to light the LCDs Fluorescent Lamp. Specifications for the FL inverter are listed in Table 1-4. Table 1-4 FL inverter board specifications
Item Input Output Voltage Power Voltage Current Specifications (V) (W) (Vrms) (mA) 5 2.3 800 2.0 to 3.5*
*NOTE: The FL currents at power on are: Level 3 : 3.5mA Level 2 : 2.9mA
Level 1 : 2.6mA
Level 0 : 2.0mA
1-13
File No. 960-140
1.7
Power Supply
The power supply supplies ten kinds of voltages to the system board, has one microprocessor and it operates at 4MHz. It performs the following functions: 1. Determines if the AC adapter or battery is connected to the computer. 2. Detects DC output and circuit malfunctions. 3. Controls the battery icon, and DC IN icon. 4. Turns the battery charging system on and off and detects a fully charged battery. 5. Determines if the power can be turned on and off. 6. Provides more accurate detection of a low battery. 7. Calculates the remaining battery capacity. The embedded controller operates at 2MHz and has the following functions: 1. Controls ACPI in Windows 98. 2. Monitors the computers temperature. 3. Controls power supply to the docking port. 4. General purpose port.
1-14
File No. 960-140 The power supply output rating is specified in Table 1-5. Table 1-5 Power supply board output rating
Power supplied Yes/No Use CPU CPU, CLKGEN, System Controller GA CLKGEN System Controller GA, PC Card Slot, VGA Controller, I/O & PC Card Controller GA, DRAM VGA Controller, PC Card Slot Flash Memory, KBC, IPSC, LCD Panel, HDD, LEDs, Sound, E2PROM,GA KB/Mouse Port PSC Embedded Controller RTC Name +1.8V +2.5V +3.3V B3V Voltage(V) 1.8 2.5 3.3 3.3 Suspend NO NO NO YES Power off NO NO NO NO No battery NO NO NO NO
B5V VCC
5.0 5.0
YES NO
NO NO
NO NO
IFVCC MCV S5V RTCV
5.0 5.0 5.0 5.0
NO YES YES YES
NO YES YES YES
NO NO NO YES
1-15
File No. 960-140
1.8
Batteries
The computer has tow types of batteries: Main battery pack RTC battery The battery specifications are listed in Table 1-6. Table 1-6 Battery specifications
Battery name Main battery Material Lithium-Ion Output voltage 10.8 V Capacity 1,200 mAh 2,400 mAh (High capacity) RTC battery Nickel Metal Hydride 2.4 V 11 mAh
1.8.1 Main Battery
The removable main battery pack is the computers main power source when the Universal AC Adapter is not connected. The main battery pack maintains the state of the computer when the computer enters in resume mode. 1.8.2 Battery Icon The icon shows the status of the removable battery pack. The status of each can be determined by color: Orange Green Blinking orange No light The battery is being charged. (Universal AC Adapter connected) The battery is full charged. (Universal AC Adapter connected) The battery is low when the power is on. Under any other conditions, the LED does not light.
1-16
File No. 960-140
1.8.3 Battery Charging Control Battery charging is controlled by a power supply microprocessor that is mounted on the system board. The microprocessor controls whether the charge is on or off and detects a full charge when the Universal AC Adapter and battery are connected to the computer. The system charges the battery using quick charge or trickle charge. Quick Battery Charge The battery quick charges when the Universal AC Adapter is connected and the system is powered off or in suspend mode. Table 1-7 Time required for quick charges
Status Quick charge 1(power off) Quick charge 2(power on) Charging time 2 to 3 hours 5 to 6 hours
If any of the following occurs, the Main Battery quick charge process stops. 1. The Main Battery becomes fully charged. 2. The AC adapter or Main Battery is removed. 3. The Main Battery or output voltage is abnormal. Trickle Battery Charge When the main battery is fully charged and the AC adapter is attached, the microprocessor automatically changes quick charge 1 or 2 to trickle charge. 1.8.4 RTC Battery The RTC battery provides power to keep the current date, time and other setup information in memory while the computer is turned off. Table 1-8 lists the charging time and data preservation period of the RTC battery. Table 1-8 RTC battery charging/data preservation time
Status Charging Time Data preservation period (full charge) Time 48 hours 1 month
1-17
File No. 960-140
1-18
File No. 960-140
Chapter 2 Troubleshooting Procedures
File No. 960-140
2-ii
File No. 960-140
Chapter 2
2.1 2.2 2.3
Contents
Troubleshooting......................................................................................................2-1 Troubleshooting Flowchart.....................................................................................2-2 Power Supply Troubleshooting...............................................................................2-6 Procedure 1 Procedure 2 Procedure 3 Procedure 4 Procedure 5 Power Status Check.............................................................2-6 Error Code Check................................................................2-8 Connection Check..............................................................2-11 Quick Charge Check ..........................................................2-12 Replacement Check............................................................2-13 Message Check ..................................................................2-15 Printer Port LED Check on Boot Mode..............................2-17 Printer Port LED Check on Resume Mode.........................2-23 Diagnostic Test Program Execution Check.........................2-24 Replacement Check............................................................2-24 FDD Head Cleaning Check ................................................2-25 Diagnostic Test Program Execution Check.........................2-26 Connector Check and Replacement Check..........................2-27 Message Check ..................................................................2-29 Partition Check ..................................................................2-30 Format Check ....................................................................2-31 Diagnostic Test Program Execution Check.........................2-32 Connector Check and Replacement Check..........................2-33 Diagnostic Test Program Execution Check.........................2-34 Connector and Replacement Check....................................2-35
2.4
System Board Troubleshooting.............................................................................2-14 Procedure 1 Procedure 2 Procedure 3 Procedure 4 Procedure 5
2.5
FDD Troubleshooting...........................................................................................2-25 Procedure 1 Procedure 2 Procedure 3
2.6
HDD Troubleshooting ..........................................................................................2-28 Procedure 1 Procedure 2 Procedure 3 Procedure 4 Procedure 5
2.7
Keyboard Troubleshooting....................................................................................2-34 Procedure 1 Procedure 2
2-iii
File No. 960-140 2.8 Pointing Device Troubleshooting..........................................................................2-36 Procedure 1 Procedure 2 2.9 Procedure 1 Procedure 2 Diagnostic Test Program Execution Check.........................2-36 Connector and Replacement Check ....................................2-36 Diagnostic Test Program Execution Check.........................2-37 Connector and Replacement Check....................................2-38
Display Troubleshooting.......................................................................................2-37
Figures Figure 2-1 Troubleshooting flowchart ...............................................................................2-3 Figure 2-2 Printer port LED............................................................................................2-17
Tables Table 2-1 Battery icon.......................................................................................................2-6 Table 2-2 DC IN icon........................................................................................................2-7 Table 2-3 Printer port LED boot mode status .................................................................2-18 Table 2-4 Printer port LED Resume mode error status.....................................................2-23 Table 2-5 FDD error code and status...............................................................................2-26 Table 2-6 Hard disk drive error code and status...............................................................2-32
2-iv
File No. 960-140

1
1.1
Troubleshooting
Chapter 2 describes how to determine if a Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. System Board 2. FL Inverter Board 3. Floppy Disk Drive 4. Hard Disk Drive 5. Keyboard 6. Display 7. Pointing Board
The Diagnostics Disk operations are described in Chapter 3. Detailed replacement procedures are given in Chapter 4. The following tools are necessary for implementing the troubleshooting procedures: 1. Diagnostics Disk 2. Phillips screwdriver (2 mm) 3. Toshiba MS-DOS system disk(s) (You must install the following onto the disk: SYS.COM, FORMAT.COM, FDISK.COM and FDISK.EXE) 4. 2DD or 2HD formatted work disk for floppy disk drive testing 5. Cleaning kit for floppy disk drive troubleshooting 6. Printer port LED 7. Printer port wraparound connector 8. Serial port wraparound connector 9. PC card wraparound card 10. Multimeter 11. I/O Adapter 12. External FDD
1-1
File No. 960-140
1.2
Troubleshooting Flowchart
Use the flowchart in Figure 2-1 as a guide for determining which troubleshooting procedures to execute. Before going through the flowchart steps, verify the following: Ask the user if a password is registered and, if it is, ask him or her to enter the password. If the user has forgotten the system password, perform the following procedure at the appropriate step in the flowchart in Figure 2-1: Connect the printer port wraparound board (F31PRT), then turn the POWER switch on. The computer will override the password function by erasing the current password. Verify with the customer that Toshiba Windows 95 is installed on the hard disk. NonToshiba operating systems can cause the computer to malfunction. Make sure all optional equipment is removed from the computer. Make sure the floppy disk drive is empty.
1-2
File No. 960-140
Figure 2-1 Troubleshooting flowchart (1/2)
1-3
File No. 960-140
Figure 2-1 Troubleshooting flowchart (2/2) If the diagnostics program cannot detect an error, the problem may be intermittent. The Running Test program should be executed several times to isolate the problem. Check the Log Utilities function to confirm which diagnostic test detected an error, then perform the appropriate troubleshooting procedures as follows: 1. If an error is detected on the system test, memory test, display test, async test, printer test, expansion test, sound test or real timer test, perform the System Board Troubleshooting Procedures in Section 2.4. 2. If an error is detected on the floppy disk test, perform the FDD Troubleshooting Procedures in Section 2.5. 3. If an error is detected on the hard disk test, perform the HDD Troubleshooting Procedures in Section 2.6.
1-4
File No. 960-140 4. If an error is detected on the keyboard test, perform the Keyboard Troubleshooting Procedures in Section 2.7. 5. If an error is detected on the display test, perform the Display Troubleshooting Procedures in Section 2.9.
1-5
File No. 960-140
1.3
Power Supply Troubleshooting
The power supply controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed. The procedures described in this section are: Procedure 1: Power Status Check Procedure 2: Error Code Check Procedure 3: Connection Check Procedure 4: Quick Charge Check Procedure 5: Replacement Check Procedure 1 Power Status Check
The following icons indicate the power supply status: Battery icon DC IN icon The power supply controller displays the power supply status through the Battery and the DC IN icons as listed in the tables below. Table 2-1 Battery icon
Battery icon Lights orange Lights green Blinks orange (even intervals) Flashes orange Doesnt light Quick charge Battery is fully charged and AC adapter is connected The battery level becomes low while operating the computer on battery power.*1 *2 The power switch is pressed on when the battery level is low. Any condition other than those above. Power supply status
*1 Auto Hibernation Off will be executed soon. *2 Auto Hibernation Off has already been executed.
1-6
File No. 960-140 Table 2-2 DC IN icon

DC IN icon Lights green Blinks orange Doesnt light Power supply status DC power is being supplied from the AC adapter. *3 Power supply malfunction Any condition other than those above.
*3 When the power supply controller detects a malfunction, the DC IN icon blinks and an error code is displayed. To check the power supply status, install a battery pack and connect an AC adapter. Check 1 Check 2 Check 3 If the DC IN icon blinks orange, go to Procedure 2. If the DC IN icon does not light, go to Procedure 3. If the battery icon does not light orange or green, go to Procedure 4.
CAUTION: Use only an AC adapter manufactured for the Libretto 100CT. If you use another AC adapter, the computer's power supply may malfunction or a fuse on the system board may be blown.
1-7
File No. 960-140
Procedure 2
Error Code Check
If the power supply microprocessor detects a malfunction, the DC IN icon blinks orange. The blink pattern indicates an error as shown below. Start Error code (8 bit) 1 0 Interval between data bits On for one second On for half second Off for half second Off for 2 seconds
The error code begins with the least significant digit. Example: Error code 12h (Error codes are given in hexadecimal format.)
Check 1
Convert the DC IN icon blink pattern into the hexadecimal error code and compare it to the tables below.
DC power supplied through AC adapter

Error code 10h 12h 13h 14h Meaning AC Adapter voltage is over 16.5V (15V+10%). Current from the DC power supply is over the limit (3.13A). Current from the DC power supply is over the limit (0.5A) when there is no load. Current sensing IC is not normal.
1-8
File No. 960-140 Main Battery

Error code 20h 21h 22h 23h 24h 25h Meaning Battery voltage is over the limit (13.46V). Main battery charge current is over the limit (2.53A). Mai battery discharge current is over the maximum allowed limit when there is no load (0.5A). Main battery charge current is over limit (1.80A) whenthere . Current sensing IC is not normal. Main battery charge current is over the limit (0.5A).
S5V output
Error code 40h Meaning S5V voltage is under the limit (4.75V).
B5V output
Error code 50h 51h 52h 53h Meaning B5V voltage is over the limit (5.5V). B5V voltage is under the limit (4.5V) when power supply is turned on. B5V voltage is under the limit (4.5V) when the computer is booting up. B5V dose not start up when the computer is suspended.
B3V output
Error code 60h 61h 62h 63h Meaning B3V voltage is over the limit (3.8V). B3V voltage is under the limit (2.81V) when power supply is turned on. B3V voltage is under the limit (2.81V) when the computer is booting up. B3V dose not start up when the computer is suspended.
1-9
File No. 960-140 B2V output

Error code 70h 71h 72h 73h Meaning B2V voltage is over the limit (2.88V). B2V voltage is under the limit (2.13V) when power supply is turned on. B2V voltage is under the limit (2.13V) when the computer is booting up. B2V voltage is over the limit (2.13V) when power supply is turned off.
B1V output
Error code 80h 81h 82h 83h Meaning B1V voltage is over the limit (2.16V). B1V voltage is under the limit (1.44V) when power supply is turned on. B1V voltage is under the limit (1.44V) when the computer is booting up. B1V voltage is over the limit (1.44V) when power supply is turned off.
Check 2
In the case of error code 10h: Make sure the AC adapter is firmly connected to the computer is DC IN socket and to power source. If this cables are connected correctly, go to the following step: Replace the AC adapter with a new one. If the error still exists, go to Procedure 5.
Check 3
In the case of error code 20h: Make sure the battery pack is correctly installed in the computer. If the battery pack is correctly installed, go to the following step: Replace the battery pack with a new one. If the error still exists, go to Procedure 5.
Check 4
In the case of error code 21h: Go to Procedure 3.
Check 5
When for any other error, go to Procedure 5.
1-10
File No. 960-140
Procedure 3
Connection Check
The power supply wiring diagram is shown below:
Any of the connectors may be disconnected. Perform Check 1. Check 1 Make sure the Libretto 100's AC adapter is firmly connected to the computer's DC IN socket and a power source. If these cables are connected correctly, go to Check 2. Replace the AC adapter with a new one. If the DC IN icon does not glow green, go to Procedure 5.
Check 2
1-11
File No. 960-140 Procedure 4 Quick Charge Check
The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adapter and turn on the power. If you cannot turn on the power, go to Procedure 5. 3. Run the Diagnostic test, go to System test and execute subtest 06 (quick charge) described in Chapter 3. 4. When quick charge is complete, the diagnostics test displays the result code. Check the result code against the table below and perform any necessary check.
Result code 0 1 2 3 4 5 6 7 8 Contents The battery is quick charging normally. The battery is fully charged. The AC adapter is not attached. The AC adapters output voltage is not normal. The Battery is not installed. The batterys output voltage is not normal. The batterys temperature is not normal. A bad battery is installed. Any other problems. Check items Normal Normal Check 1 Check 1 Check 2 Check 3 Check 4 Check 2 Check 5
Check 1
Make sure the AC adapter and AC power cord are firmly plugged into the DC IN socket and the wall outlet. If these cables are connected correctly, replace the AC power cord and AC adapter. Make sure the battery is properly installed. If the battery is properly installed, replace it with a new one. The battery pack may be completely discharged. Wait a few minutes to charge the battery pack. If the battery pack is still not charged, replace the battery pack with a new one. The batterys temperature is too hot or cold. Return the temperature to a normal operating condition. If the battery pack still is not charged, replace the battery pack with a new one. Go to Procedure 5.
Check 2 Check 3
Check 4
Check 5
1-12
File No. 960-140
Procedure 5
Replacement Check
The AC adapter may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures. After checking the connection, perform the following checks: Check 1 Check 2 Replace the AC adapter with a new one. If the problem still exists, go to Check 2. Replace the system board with a new one. Refer to Chapter 4 for instructions on how to remove and replace the system board.
1-13
File No. 960-140
1.4
System Board Troubleshooting
This section describes how to determine if the system board is defective or not functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. The procedures described in this section are: Procedure 1: Message Check Procedure 2: Printer Port LED Check on Boot Mode Procedure 3: Printer Port LED Check on Resume Mode Procedure 4: Diagnostic Test Program Execution Check Procedure 5: Replacement Check
1-14
File No. 960-140
Procedure 1
Message Check
When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. The IRT tests each IC on the system board and initializes it. If an error message is shown on the display, perform Check 1. If there is no error message, go to Procedure 2. If Toshiba MS-DOS or Toshiba Windows 95 is properly loaded, go to Procedure 4. Check 1 If one of the following error messages displays on the screen, press the F1 key as the message instructs. These errors occur when the system configuration preserved in the RTC memory (CMOS type memory) is not the same as the actual configuration or when the data is lost. If you press the F1 key as the message instructs, the TSETUP screen appears to set the system configuration. If error message (b) appears often when the power is turned on, replace the RTC battery. If any other error message displays, perform Check 2.
(a) (b) (c) (d) (e) (f) (g) *** Bad HDD type *** Check system. Then press [F1] key *** Bad RTC battery *** Check system. Then press [F1] key *** Bad configuration *** Check system. Then press [F1] key *** Bad memory size *** Check system. Then press [F1] key *** Bad time function *** Check system. Then press [F1] key *** Bad check sum (CMOS) *** Check system. Then press [F1] key *** Bad check sum (ROM) *** Check system. Then press [F1] key ...... ...... ...... ...... ...... ...... ......
Check 2
If the following error message displays on the screen, press any key as the message instructs. If any other error message displays, perform Check 3. The following error message appears when data stored in RAM under the resume function is lost because the battery has become discharged or the system board is damaged. Go to Procedure 3. WARNING: RESUME FAILURE.
PRESS ANY KEY TO CONTINUE.
1-15
File No. 960-140 Check 3 The IRT checks the system board. When the IRT detects an error, the system stops or an error message appears. If one of the following error messages (1) through (17), (24) or (25) displays, go to Procedure 5. If error message (18) displays, go to the Keyboard Troubleshooting Procedures in Section 2.7. If error message (19), (20) or (21) displays, go to the HDD Troubleshooting Procedures in Section 2.6. If error message (22) or (23) displays, go to the FDD Troubleshooting Procedures in Section 2.5. (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) (25) PIT ERROR MEMORY REFRESH ERROR TIMER CH.2 OUT ERROR CMOS CHECKSUM ERROR CMOS BAD BATTERY ERROR FIRST 64KB MEMORY ERROR FIRST 64KB MEMORY PARITY ERROR VRAM ERROR SYSTEM MEMORY ERROR SYSTEM MEMORY PARITY ERROR EXTENDED MEMORY ERROR EXTENDED MEMORY PARITY ERROR DMA PAGE REGISTER ERROR DMAC #1 ERROR DMAC #2 ERROR PIC #1 ERROR PIC #2 ERROR KBC ERROR HDC ERROR HDD #0 ERROR HDD #1 ERROR NO FDD ERROR FDC ERROR TIMER INTERRUPT ERROR RTC UPDATE ERROR
1-16
File No. 960-140
Procedure 2
Printer Port LED Check on Boot Mode
The printer port LED displays the IRT status and test status by turning lights on and off as an eight-digit binary value for boot mode. Figure 2-2 shows the printer port LED.
Figure 2-2 Printer port LED To use the printer port LED follow the steps below: 1. Plug the printer port LED into the computers parallel port. 2. Hold down the space bar and turn on the computers power. 3. Read the LED status from left to right as you are facing the back of the computer. 4. Convert the status from binary to hexadecimal notation. 5. If the final LED status is FFh (normal status), go to Procedure 4. 6. If the final LED status matches any of the test status values in Table 2-3, perform Check 1. NOTE: If an error condition is detected by the IRT test, the printer port LED displays an error code after the IRT test ends. For example, when the printer port LED displays 1F and halts, the IRT test has already completed the Display initialization. In this instance, the IRT indicates an error has been detected during the system memory test.
1-17
File No. 960-140 Table 2-3 Printer port LED boot mode status (1/5)
LED Status FFh B0h
Start Flash ROM check
Test item
Message
Register initialization for boot block PIT ch.0 initialization BIOS rewrite flag initialization Transition to protected mode Boot block checksum KBC initialization BIOS (runtime and IRT) checksum
B2h B3h
KBC initialization (1)

BIOS rewrite
KBC initialization BIOS rewrite request check Canceling power down of L2-cache Enabling CMOS access Port 25h unlock
00h
Special register initialization
Toshiba register initialization (1) Toshiba register initialization (2)
01h
Memory check
DRAM size check Memory structure configuration SM-RAM stack area test
05h
CMOS check and initialization ROM to RAM copy
Enabling cache
CMOS access test CMOS checksum CMOS data initialization Set DRAM size Resume branch check CMOS error check Resume status check SM-RAM checksum System BIOS checksum Toshiba register initialization (3) Set SM-RAM base address Grant SMI KBC initialization
1-18
LED Status 05h Test item
PIT initialization Start resume sequence Resume error process SM-RAM initialization ROM to RAM copy and enabling shadow RAM Toshiba register initialization (3)
Message
06h
SMI initialization KBC initialization (2)
SM-RAM base rewrite Set SMI handler Grant SMI Estimate operation clock speed Grant all SMIs Measure for miscellaneous GA Date check for alarm power on Canceling HDD hardware reset Set COMS default configuration when CMOS error detected KBC initialization
03h
VGA initialization Sound initialization PIT initialization
VGA controller power off and reset control Sound controller initialization PIT test and initialization PIC initialization PIC test CPU type discrimination Self-test control status initialization
04h
PIC initialization
02h
PCI initialization
PCI initialization Detection of VGA controller on ISA
71h
Set CMOS initialize register
Printer port wraparound connector detection CMOS data initialization for APM Set divider control register Set counter control register Set configuration number and sleep counter initialization
1-19
LED Status 07h 73h 72h 74h 76h Test item
PnP initialization Desk station initialization Get PnP information Password initialization TSETUP PnP initialization Initialization of NS Super I/O in desk station PnP ISA card separation and get resource information Password initialization TSETUP hardware configuration Issuing power off grant command Set CPU speed Set speaker Set battery alarm Set panel close alarm Set panel power on/off PnP system resource configuration
Message
79h
Serial port configuration PC card configuration PnP automatic configuration
Serial port configuration

Modem port configuration PC card initialization PnP automatic configuration
77h
EC and PSC configuration
Grant embedded controller SMI SLP_TYP setting Power supply microprocessor configuration
78h
PCI device initialization (1)
Ensure work area for automatic configuration Initialization of work area Create reserved resource map
81h 82h 83h
PCI device initialization (2) PCI device initialization (3) PCI device initialization (4)
Add reserved resource for primary display device to map Add reserved variable resource to map PCI automatic configuration Special process after PCI configuration
1-20
LED Status 7Bh Test item
HDD initialization FDD initialization
Message
Printer port configuration HDD initialization Serial interrupt control FDD initialization Open closing PCI device
7Ch
BIOS RAM update
IRQ routing table update Copying parameter in IRT BIOS to runtime BIOS
7Ah 08h 09h 0Dh
VGA initialization Output code generation First 64 KB memory check System configuration
Video card recognition and wait for VGA chip initialization Output code generation First 64 KB memory check Store CMOS error information to SM-RAM Timer initialization Get version of embedded controller and PS microprocessor Set default value to embedded controller Toshiba special register initialization Grant SMI from docking port and Selectable Bay
19h
Display initialization Selectable Bay lock check
VGA BIOS initialization Selectable Bay lock check Displaying logo PnP automatic configuration PnP ISA card isolation Search assignable resource and card configuration
1Fh 20h
Displaying logo PnP configuration
21h 25h 30h 40h 41h 42h 70h 80h
System memory check Expansion memory check DMA page check DMAC check DMAC configuration Printer port check SIO check NDP configuration
System memory check Expansion memory check DMA page check DMAC check DMAC configuration Printer port check SIO check NDP configuration
1-21
LED Status A0h C0h A6h Test item
Boot password External I/O check BIOS information update Boot password External I/O check Set font address Set shadow RAM size Set expansion memory size to CMOS System resource update Set extended memory size to runtime BIOS for INT15h ACPI table update Set SCT area to runtime BIOS Set battery save mode Send date to PS microprocessor Close PCI device configuration area Protect system BIOS Cache control
Message
FEh FFh
System ROM check End
System ROM check
Check 1
If any of the following error codes display, go to Procedure 5. B0h, B2h, B3h, 00h, 01h, 05h, 06h, 03h, 04h, 02h, 71h, 07h, 73h, 74h, 72h, 76h, 79h, 77h, 78h, 81h, 82h, 7Bh, 7Ch, 7Ah, 08h, 09h, 0Dh, 19h, 1Fh, 20h, 21h, 25h, 30h, 40h, 41h, 42h, 70h, 80h, A0h, C0h, A6h, FEh
Check 2
If error code 83h is displayed, go to the following sections: Section 2.5. FDD Troubleshooting Section 2.6. HDD Troubleshooting
1-22
File No. 960-140
Procedure 3
Printer Port LED Check on Resume Mode
The printer port LED displays the IRT status and test status by turning lights on and off as an eight-digit binary value for Hibernation mode. To use the printer port LED follow the steps below: 1. Make sure the computer is in Resume mode. 2. Plug the printer port LED into the computers parallel port. 3. Turn on the computers power. 4. Read the LED status from left to right as you face the back of the computer. 5. Convert the status from binary to hexadecimal notation. 6. If the final LED status is FFh (normal status), go to Procedure 4. 7. If the final LED status matches any of the test status values in Table 2-4, perform Procedure 5. Table 2-4 Printer port LED Resume mode error status
Error status F1H F2H F3H F4H F5H F7H F8H Meaning of status System BIOS RAM checksum error External display card is connected. HDD was installed. SMRAM checksum error or memory error during suspend Conventional memory checksum error Extended memory checksum error PnP RAM checksum error
1-23
File No. 960-140
Procedure 4
Diagnostic Test Program Execution Check
Execute the following tests from the Diagnostic Test Menu. Refer to Chapter 3,Tests and Diagnostic, for more information on how to perform these tests. 1. System test 2. Memory test 3. Keyboard test 4. Display test 5. Floppy Disk test 6. Printer test 7. ASYNC test 8. Hard Disk test 9. Real Timer test 10. NDP test 11. Expansion test 12. Sound test If an error is detected during these tests, go to Procedure 5. Procedure 5 Replacement Check
The system board may be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and replace the system board with a new one.
1-24
File No. 960-140
1.5
FDD Troubleshooting
This section describes how to determine if the FDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: FDD Head Cleaning Check Procedure 2: Diagnostic Test Program Execution Check Procedure 3: Connector Check and Replacement Check Procedure 1 FDD Head Cleaning Check
FDD head cleaning is one option available in the Diagnostic Program. A detailed operation is given in Chapter 3, Tests and Diagnostics. Insert the Diagnostics Disk in the computers floppy disk drive, turn on the computer and run the test. Clean the FDD heads using the cleaning kit. If the FDD still does not function properly after cleaning, go to Procedure 2. If the test program cannot be executed on the computer, go to Procedure 2.
1-25
File No. 960-140
Procedure 2
Insert the Diagnostics Disk in the FDD, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more information about the diagnostics test procedures. Floppy disk drive test error codes and their status names are listed in Table 2-5. Make sure the floppy disk is formatted correctly and that the write protect tab is disabled. If any other errors occur while executing the FDD diagnostics test, go to Check 1. Table 2-5 FDD error code and status
Code 01h 02h 03h 04h 06h 08h 09h 10h 20h 40h 60h 80h EEh FFh Bad command Address mark not found Write protected Record not found Media removed on dual attach card DMA overrun error DMA boundary error CRC error FDC error Seek error FDD not drive Time out error (Not ready) Write buffer error Data compare error Status
Check 1
If the following message displays, disable the write protect tab on the floppy disk. If any other message appears, perform Check 2. Write protected
Check 2
Make sure the floppy disk is formatted correctly. If it is, go to Procedure 3.
1-26
File No. 960-140
Procedure 3
Connector Check and Replacement Check
The FDD, cable and PC card is a single unit. Install the FDD's PC card in the computer, then begin with Check 1 below. Check 1 Make sure the PC card is properly connected to the system board.
If the connection is loose, reinstall the PC card and repeat Procedure 2. If there is still an error, go to Check 2. Check 2 Check 3 The FDD may be defective or damaged. Replace the FDD with a new one. If the FDD is still not functioning properly, perform Check 3. Replace the system board with a new one following the steps in Chapter 4, Replacement Procedures.
1-27
File No. 960-140
1.6
HDD Troubleshooting
This section describes how to determine if the HDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Message Check Procedure 2: Partition Check Procedure 3: Format Check Procedure 4: Diagnostic Test Program Execution Check Procedure 5: Connector Check and Replacement Check NOTE: The contents of the hard disk will be erased when the HDD troubleshooting procedures are executed. Transfer the contents of the hard disk to floppy disk or other device. If the customer has not or cannot perform the backup, create backup disks as described below. Check to see if the Microsoft Create System Disks Tools (MSCSD.EXE) still exists in the System Tools Folder. (This tool can be used only once.) If it exists, use it to back up the preinstalled software, then use the Backup utility in the System Tools folder to back up the entire disk, including the user's files. Refer to the operating system instructions.
1-28
File No. 960-140
Procedure 1
Message Check
When the computers HDD does not function properly, some of the following error messages may appear on the display. Start with Check 1 below and perform the other checks as instructed. Check 1 If any of the following messages appear, go to Procedure 5. If the following messages do not appear, perform Check 2. HDC ERROR (After 5 seconds this message will disappear.) or HDD #0 ERROR (After 5 seconds this message will disappear.) or HDD #1 ERROR (After 5 seconds this message will disappear.) Check 2 If either of the following messages appears, go to Procedure 2. If the following messages do not appear, perform Check 3. Insert system disk in drive Press any key when ready ..... or Non-System disk or disk error Replace and press any key Check 3 Check TSETUP to see whether the Hard Disk option is set to Not used. If it is set to Not used, choose another setting and restart the computer. If the problem still exists, go to Procedure 2.
1-29
File No. 960-140
Procedure 2
Partition Check
Insert the Toshiba MS-DOS system disk and restart the computer. Perform the following checks: Check 1 Check 2 Type C: and press Enter. If you cannot change to drive C, go to Check 2. If you can change to drive C, go to Check 3. Type FDISK and press Enter. Choose Display Partition Information from the FDISK menu. If drive C is listed, go to Check 3. If drive C is not listed, return to the FDISK menu and choose the option to create a DOS partition on drive C. Restart the computer from the Toshiba MS-DOS system disk. If the problem still exists, go to Procedure 3. If drive C is listed as active in the FDISK menu, go to Check 4. If drive C is not listed as active, return to the FDISK menu and choose the option to set the active partition for drive C. Restart the computer. If the problem still exists, go to Check 4. Type DIR C: and press Enter. If the following message displays, go to Procedure 3. If contents of drive C are listed on the display, go to Check 5.
Invalid media type reading drive C Abort, Retry, Fail?
Check 3
Check 4
Check 5
Using the SYS command on the Toshiba MS-DOS system disk, install system files on the HDD. If the following message appears on the display, the system files have been transferred to the HDD. Restart the computer. If the problem still exists, go to Procedure 3.
System transferred
1-30
File No. 960-140
Procedure 3
Format Check
The computers HDD is formatted using the low level format program and the MS-DOS FORMAT program. To format the HDD, start with Check 1 below and perform the other steps as required. Check 1 Format the HDD and transfer system files using FORMAT C:/S/U. If the following message appears on the display, the HDD is formatted.
Format complete
If an error message appears on the display, refer to the Toshiba MS-DOS Manual for more information and perform Check 2. Check 2 Using the Diagnostic Disk, format the HDD with a low level format option. Refer to Chapter 3, Tests and Diagnostics for more information about the diagnostic program. If the following message appears on the display, the HDD low level format is complete. Partition and format the HDD using the MS-DOS FORMAT command.
Format complete
If you cannot format the HDD using the Tests and Diagnostic program, go to Procedure 4.
1-31
File No. 960-140
Procedure 4
The HDD test program is stored in the Diagnostics Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about the HDD test program. If an error is detected during the HDD test, an error code and status will display. The error codes and statuses are listed in Table 2-6. If an error code is not generated and the problem still exists, go to Procedure 5. Table 2-6 Hard disk drive error code and status
Code 01h 02h 04h 05h 07h 08h 09h 0Ah 0Bh 10h 11h 20h 40h 80h AAh BBh CCh E0h EEh DAh Bad command Bad address mark Record not found HDC not reset Drive not initialized HDC overrun (DRQ) DMA boundary error Bad sector error Bad track error ECC error ECC recover enable HDC error Seek error Time out error Drive not ready Undefined error Write fault Status error Access time out error No HDD Status
1-32
File No. 960-140 Procedure 5 Connector Check and Replaceme nt Check
The HDD or system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: Check 1 Make sure the HDD is firmly connected to system board.
If any of the connections are loose, reconnect firmly and repeat Procedure 1. If there is still an error, go to Check 2. Check 2 Check 3 The HDD may be damaged. Replace it with a new one following the instructions in Chapter 4. If the problem still exists, perform Check 3. The system board may be damaged. Replace it with a new one following the instructions in Chapter 4.
1-33
File No. 960-140
1.7
Keyboard Troubleshooting
To determine if the computers keyboard is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector and Replacement Check Procedure 1 Diagnostic Test Program Execution Check
Execute the Keyboard Test in the Diagnostic Program. Refer to Chapter 3, Test and Diagnostics, for more information on how to perform the test program If an error occurs, go to Procedure 2. If an error does not occur, the keyboard is functioning properly If the external keyboard appears to have the same problem as the internal keyboard, the system board may be damaged. Go to Procedure 2.
1-34
File No. 960-140
Procedure 2
Connector and Replacement Check
The keyboard is connected to the system board by flat cables. These cables or connectors may be disconnected or damaged. If there is a problem with the keyboard, disassemble the computer as described in Chapter 4, Replacement Procedures, and perform Check 1. Check 1 Make sure the following cables are not damaged and are connected to the system board.
If the cables are damaged, replace the keyboard with a new one. If the cable is disconnected, firmly connect it. Perform Procedure 1 again. If the error still exists, perform Check 2. Check 2 The system board may be damaged. Replace the system board with a new one. Refer to Chapter 4, Replacement Procedures for more information.
1-35
File No. 960-140
1.8
Pointing Device Troubleshooting
To determine if the computer's pointing device is functioning properly, perform the following procedures. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector and Replacement Check Procedure 1 Diagnostic Test Program Execution Check
Execute the pointing device Test in the Diagnostic Program of Keyboard Test Program. Refer to Chapter 3, Test and Diagnostic, for more information on how to perform the test program. If an error occurs, go to Procedure 2. If an error does not occur, the pointing device is functioning properly. Procedure 2 Connector and Replacement Check
The pointing device is connected to the system board by the FLIMC* board (flexible cable). The FLIMC* board or connectors may be disconnected or damaged. If there is a problem with the pointing device, disassemble the computer as described in Chapter 4.Replacement Procedures, and perform Check 1. Check 1 Make sure the FLIMC* board or the pointing device is not damaged and that both are connected to the system board. If the FLIMC* board or the pointing device is damaged, replace the FLIMC* board or the pointing device with a new one. If the FLIMC* board or the pointing device is disconnected, firmly connect it. Perform Procedure 1 again. If the error still exists, perform Check 2. The System board may be damaged. Replace the System board with a new one. Refer to Chapter 4, Replacement Procedures for more information.
Check 2
1-36
File No. 960-140
1.9
Display Troubleshooting
This section describes how to determine if the computers display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector and Replacement Check Procedure 1 Diagnostic Test Program Executi on Check
The Display Test program is stored on the computers Diagnostics disk. This program checks the display controller on the system board. Insert the Diagnostics disk in the computers floppy disk drive, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics for details. If an error is detected, go to Procedure 2. If an error is not detected, the display is functioning properly.
1-37
File No. 960-140
Procedure 2
Connector and Replacement Check
The FL, FL inverter board, LCD module, LCD flat cable and system board are connected to the display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: If the FL does not light, perform Check 4. If characters are not displayed clearly, perform Check 3. If some screen functions do not operate properly, perform Check 3. If the FL remains lit when the display is closed, perform Check4. Check 1 Check 2 Check 3 Check 4 Check 5 Replace the LCD flat cable with a new one and test the display again. If the problem still exists, perform Check 2. Replace the LCD module with a new one and test the display again. If the problem still exists, perform Check 3.. Replace the FL inverter board with a new one and test the display again. If the problem still exists, perform Check 4. Replace the FL with a new one and test the display again. If the problem still exists, perform Check 5. The system board may be damaged. Replace the system board with a new one.
1-38
File No. 960-140
Chapter 3 Tests and Diagnostics
File No. 960-140
3-ii
File No. 960-140
Chapter 3
3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18
Contents
The Diagnostic Test................................................................................................3-1 Executing the Diagnostic Test.................................................................................3-3 Subtest Names........................................................................................................3-7 System Test............................................................................................................3-9 Memory Test ........................................................................................................3-10 Keyboard Test ......................................................................................................3-12 Display Test..........................................................................................................3-16 Floppy Disk Test ..................................................................................................3-20 Printer Test...........................................................................................................3-22 Async Test............................................................................................................3-24 Hard Disk Test .....................................................................................................3-26 Real Timer Test....................................................................................................3-30 NDP Test .............................................................................................................3-32 Expansion Test .....................................................................................................3-33 Sound Test ...........................................................................................................3-35 Error Code and Error Status Names......................................................................3-36 Hard Disk Test Detail Status.................................................................................3-39 Hard Disk Format.................................................................................................3-41 3.18.1 3.18.2 Function Description........................................................................3-42 Operations .......................................................................................3-43 Function Description........................................................................3-46 Operations .......................................................................................3-46 Function Description........................................................................3-47 Operations .......................................................................................3-47 Function Description........................................................................3-49 Operations .......................................................................................3-49
3.19
Head Cleaning ......................................................................................................3-46 3.19.1 3.19.2
3.20
Log Utilities..........................................................................................................3-47 3.20.1 3.20.2
3.21
Running Test ........................................................................................................3-49 3.21.1 3.21.2
3-iii
File No. 960-140 3.22 Floppy Disk Drive Utilities....................................................................................3-51 3.22.1 3.22.2 3.23 3.23.1 3.23.2 3.24 3.24.1 3.24.2 Function Description........................................................................3-51 Operations .......................................................................................3-52 Function Description........................................................................3-56 Operations .......................................................................................3-57 Function Description........................................................................3-58 Accessing the SETUP Program........................................................3-59
System Configuration............................................................................................3-56
SETUP.................................................................................................................3-58
Tables Table 3-1 Subtest names ....................................................................................................3-7 Table 3-2 Error codes and error status names ..................................................................3-36 Table 3-3 Hard disk controller status register contents......................................................3-39 Table 3-4 Error register contents......................................................................................3-40 Table 3-5 Hard disk formatting sequence..........................................................................3-42
3-iv
File No. 960-140

3
3.1
The Diagnostic Test
This chapter explains how to use the Diagnostic Test program to test the functions of the computers hardware modules. The Diagnostics Program is stored on the Diagnostic Disk. The Diagnostic Test consists of 12 programs that are grouped into the Service Program Module (DIAGNOSTIC TEST MENU). NOTES: To start the diagnostics, follow these steps: 1. Check all cables for loose connections. 2. Exit any application you may be using and close Windows. The DIAGNOSTIC MENU consists of the following functions: DIAGNOSTIC TEST HARD DISK FORMAT HEAD CLEANING LOG UTILITIES RUNNING TEST FDD UTILITIES SYSTEM CONFIGURATION EXIT TO MS-DOS SETUP The DIAGNOSTIC TEST MENU contains the following functional tests: SYSTEM TEST MEMORY TEST KEYBOARD TEST DISPLAY TEST FLOPPY DISK TEST PRINTER TEST ASYNC TEST HARD DISK TEST REAL TIMER TEST NDP TEST EXPANSION TEST SOUND TEST
3-1
File No. 960-140 You will need the following equipment to perform some of the Diagnostic test programs. The Diagnostics Disk (all tests) A formatted working disk for the floppy disk drive test (all tests) A cleaning kit to clean the floppy disk drive heads (Head Cleaning) A PC card wraparound connector for the I/O card test (Expansion test) ( Rev.B or higher) A printer wraparound connector for the printer wraparound test (Printer test) External FDD (All tests) Serial port wraparound connector (ASYNC test) I/O Adapter The following sections detail the tests within the Diagnostic Test function of the DIAGNOSTIC TEST MENU. Refer to Sections 3.18 through 3.24 for detailed information on the remaining Service Program Module functions.
3-2
File No. 960-140
3.2
Executing the Diagnostic Test
Toshiba MS-DOS is required to run the DIAGNOSTICS PROGRAM. To start the DIAGNOSTIC PROGRAM, follow these steps: 1. Connect a wraparound connector to the I/O adapter's printer port and RS-232C port. Connect the I/O adapter to the computer. Next, connect the FDD and insert the diskette containing the test program 2. Turn on the computer and the test program will execute and the test menu will be displayed. The following menu will appear:
TOSHIBA personal computer xxx DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 19XX DIAGNOSTICS 1 2 3 4 5 6 7 8 9 0 MENU :
DIAGNOSTIC TEST HARD DISK FORMAT HEAD CLEANING LOG UTILITIES RUNNING TEST FDD UTILITIES SYSTEM CONFIGURATION EXIT TO MS-DOS SETUP
NOTE: To exit the DIAGNOSTIC TEST MENU, press the Esc key. If a test program is in progress, press Ctrl + Break to exit the test program, or press Ctrl + C to stop the test program.
3-3
File No. 960-140 3. To select the DIAGNOSTIC TEST option from the DIAGNOSTICS MENU, set the highlight bar to 1 and press Enter. The following DIAGNOSTIC TEST MENU will appear:
TOSHIBA personal computer xxx DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 19XX DIAGNOSTIC TEST MENU : 1 2 3 4 5 6 7 8 9 10 11 12 88 99 SYSTEM TEST MEMORY TEST KEYBOARD TEST DISPLAY TEST FLOPPY DISK TEST PRINTER TEST ASYNC TEST HARD DISK TEST REAL TIMER TEST NDP TEST EXPANSION TEST SOUND TEST ERROR RETRY COUNT SET [HDD & FDD] EXIT TO DIAGNOSTICS MENU
Refer to sections 3.4 through 3.16 for detailed descriptions of each Diagnostic Test 1 through 12. Function 88 sets the floppy disk drive and hard disk drive error retry count. Function 99 exits the submenus of the Diagnostic Test and returns to the Diagnostic Menu.
3-4
File No. 960-140 4. Select the option you want to execute and press Enter. The following message appears:
SYSTEM TEST XXXXXXX xxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] ; test end [Ctrl]+[C] ; key stop
SUB- TEST : XX PASS COUNT: XXXXX WRITE DATA: XX ADDRESS : XXXXXX SUB-TEST MENU : 01 02 03 04 05 06 07 08 99 ROM checksum
ERROR COUN T: XXXXX READ DATA : XX STATUS : XXX
Thermister check Quick charge DMI read DMI write Exit to DIAGNOSTIC TEST MENU
NOTE: The menu displayed by your computer may be slightly different from the one shown above. 5. Select the desired subtest number from the subtest menu and press Enter. The following message will appear:
TEST LOOP : YES ERROR STOP : YES
Use the arrow keys to move the cursor to the desired option and press Enter. Selecting YES for TEST LOOP sets the test to run continuously until halted by the user. Selecting NO returns the subtest menu to the main menu after the test is complete.
3-5
File No. 960-140 Selecting YES for ERROR STOP stops the test program when an error is found and displays the operation guide on the right side of the display screen as shown below:
ERROR STATUS NAME [ [ HALT OPERATION ]] 1: Test end 2: Continue 3: Retry
These three selections have the following functions respectively: 1. Terminates the test program and exits to the subtest menu. 2. Continues the test. 3. Restarts the test from the error. Selecting NO for ERROR STOP keeps the test running even if an error is found. Table 3-1 in Section 3.3 lists the function of each test on the subtest menu. Table 3-2 in Section 3.16 lists the error codes and error status for each error.
3-6
File No. 960-140
3.3
Subtest Names
Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/2)
No. 1 Test Name SYSTEM Subtest No. 01 05 06 07 08 01 02 03 04 05 06 01 02 03 04 05 01 02 03 04 05 01 02 03 04 05 01 02 03 Subtest Name ROM checksum Thermistor check Quick charge DMI read (Not used) DMI write (Not used) RAM constant data RAM address pattern data RAM refresh Protected mode Memory module Cache memory Pressed key display Pressed key code display PS/2 Mouse connect check Pointing Stick USB Warp around test VRAM read/write for VGA Gradation for VGA Gradation & Mode test for VGA H pattern display BUS Master Transfaer Sequential read Sequential read/write Random address/data Write specified address Read specified address Ripple pattern Function Wraparound
MEMORY
KEYBOARD
DISPLAY
FDD
PRINTER
3-7
File No. 960-140 Table 3-1 Subtest names (2/2)

No. 7 Test Name ASYNC Subtest No. 01 02 03 04 06 07 01 02 03 04 05 06 07 08 09 10 01 02 03 01 01 02 03 04 06 01 02 03 Subtest Name Wrap around (board) Point to point (send) Point to point (receive) Interrupt test FIR/SIR point to point (send) FIR/SIR point to point (receive) Sequential read Address uniqueness Random address/data Cross talk & peak shift Write/read/compare (CE) Write specified address Read specified address ECC circuit Sequential write W-R-C specified address Real time Backup memory Real time carry NDP test PCMCIA wrap around DS bus wrap around RGB monitor ID PCMCIA wrap around (External) ZV port wrap around CODEC (REC/PLAY) FM Synthesizer SIN Wave Playback
HDD
REAL TIMER
10 11
NDP EXPANSION
12
SOUND
3-8
File No. 960-140
3.4
System Test
To execute the System Test select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 ROM Checksum This subtest executes a checksum test of the BIOS ROM on the system board. Subtest 05 Thermistor Check This subtest reads the thermistor connect check status of the power supply microprocessor, then compares it with the original data. If the data indicates the connector is open or shorted, it displays an error message. Subtest 06 Quick Charge This subtest determines whether the battery pack can be quick charged. Refer to the table listing the result codes in Chapter 2.
3-9
File No. 960-140
3.5
Memory Test
To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 RAM constant data (real mode) This subtest writes a 256-byte unit of constant data to conventional memory (0 to 640 KB). Then reads the new data and compares the result with the original data. The constant data is FFFFh, AAAAh, 5555h, 0101h, and 0000h. Subtest 02 RAM address pattern data (real mode) This subtest writes address pattern data created by the exclusive-ORing (XORing), to the address segment and address offset in conventional memory program end to 640 KB, then reads the new data and compares the result with the original data. Subtest 03 RAM refresh (real mode) This subtest writes a 256-byte unit of constant data to conventional memory (0 to 640 KB) then reads the new data and compares the result with the original data. The constant data is AAAAh and 5555h. NOTE: There is a short delay between write and read operations, depending on the size of the data. Subtest 04 Protected mode NOTE: The CONFIG.SYS file must be configured without expanded memory manager programs such as EMM386.EXE, EMM386.SYS or QEMM386.SYS. Also, the HIMEM.SYS must be deleted from the CONFIG.SYS file. This subtest writes constant data and address data to extended memory (maximum address 100000h) then reads the new data and compares the result with the original data. The constant data is FFh, AAh, 55h, and 00h.
3-10
File No. 960-140 Subtest 05 Memory module NOTE: To execute this subtest, an optional memory card must be installed in the computer. This subtest functions the same as subtest 04, except it is used for testing an optional memory card. Memory module capacity is 32MB. After selecting subtest 05, the following message will appear:
Extended memory size (1:32 MB)?
Select the number that corresponds to the memory card installed in the computer. Subtest 06 Cache memory To test the cache memory, a pass-through write-read comparison of 5A data is run repeatedly to the test area (7000:Program size to 7000:7FFF (32 KB)) to check the hit-miss ratio (on/off status) for CPU cache memory. One test takes 3 seconds. Number of misses < Number of hits OK Number of misses Number of hits Fail
3-11
File No. 960-140
3.6
Keyboard Test
To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The Keyboard test contains four subtests that test the computers keyboard, PS/2 mouse, and Pointing Stick actions. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Pressed key display (80/82) NOTE: The Num Lock and the Overlay mode must be off to execute this subtest. When you execute this subtest, the keyboard layout is drawn on the display as shown below. When any key is pressed, the corresponding key on the screen changes to the key that was pressed. Holding a key down enables the autorepeat function which causes the keys display character to blink.
[[[ Press Key Display ]]]
If test OK, Press [Del] [Enter] Key
3-12
File No. 960-140 Subtest 02 Pressed key code display When a key is pressed, the scan code, character code, and key top name displays on the screen in the format shown below. The Ins, Caps Lock, Num Lock, Scroll Lock, Alt, Ctrl, Left Shift, and Right Shift keys display in reverse screen mode when pressed. The scan codes, character codes, and key top names are shown in Appendix D.
KEYBOARD TEST IN PROGRESS = 302000 Scan code = Character code Keytop =
Ins Caps Lock Num Lock Scroll Lock Alt Ctrl Left Shift Right Shift PRESS [Enter] KEY
Subtest 03
PS/2 Mouse connect check NOTE: To execute the PS/2 mouse connect check, a PS/2 mouse must be connected to the computer before the power is turned on. This subtest checks whether a PS/2 mouse is connected or not. If this test does not detect an error, it returns to the subtest menu. If it detects an error, the following message appears:
KBD - MOUSE INTERFACE ERROR [[ HALT OPERATION ]] 1: Test end 2: Continue 3: Retry
3-13
File No. 960-140 Subtest 04 Pointing stick This subtest checks the functions of the pointing stick as shown below. A) IPS stick pressure sensing direction and parameter. B) IPS switch function check. This test reports the pointing stick motion response from the IPS and IPS switch. When the stick is pressed towards the upper left, the <POINTING> display changes according to the following illustration. If an IPS switch is pressed, the <BUTTON> display alternates between black and white. The parameters appear on the right side of the display. If two IPS switches are pressed at the same time, the subtest menu displays.
3-14
File No. 960-140 Subtest 05 USB Wrap around test This subtest checks USB. The USB TEST Module (ZD0003P01) and USB Cable (ZD0003P02) must be connected to the computer. If the test is completed successfully, OK is displayed. If nothing is displayed, there may be a problem with the USB port. Check the wraparound connection and repeat the test. NOTE: To execute this subtest, the Enhanced Port Replicator must be connected to the computer.
3-15
File No. 960-140
3.7
Display Test
To execute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The Display test contains eight subtests that test the display in various modes. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 VRAM read/write for VGA This subtest writes constant data AAh and 55h and address data to video RAM (2MB: A0000h-AFFFFh). This data is then read from the video RAM and compared to the original data. Subtest 02 Gradation for VGA This subtest displays four colors: red, green, blue and white from left to right across the screen from black to maximum brightness. The display below appears on the screen when this subtest is executed.
To exit this subtest and return to the DISPLAY TEST menu, press Ctrl + Break.
3-16
File No. 960-140 Subtest 03 Gradation & mode test for VGA This subtest displays gradations for each mode. Execute the test, then press Enter to change the mode.
Resolution 800 x 480 Mode 3, 12, 13
NOTE: Mode 52 test can test only an external monitor, it cannot be used for the internal LCD. The display below appears on the screen when this subtest is executed.
Pressing Enter changes the size of the displayed image.
Pressing Enter changes the size of the displayed image.
3-17
File No. 960-140
Pressing Enter again changes the size of the displayed image.
To exit this subtest and return to the DISPLAY TEST menu, press Ctrl + Break.
3-18
File No. 960-140 Subtest 04 H pattern display This subtest displays a full screen of H patterns.
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
To exit this subtest and return to the DISPLAY TEST menu, press Ctrl + Break. NOTE: The last row may not be completely filled. This condition does not indicate on error
Subtest 05
BUS Master Transfer This subtest PCI BUS MASTER test.
3-19
File No. 960-140
3.8
Floppy Disk Test
NOTE: Before running the floppy disk test, prepare a formatted work disk. Remove the Diagnostics Disk and insert the work disk into the FDD. The contents of the floppy disk will be erased. To execute the Floppy Disk Test, select 5 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen. The Floppy Disk test contains five subtests that test the FDD. The following messages will appear after selecting the Floppy Disk Test from the DIAGNOSTIC TEST MENU. Answer each question with an appropriate response to execute the test. 1. Select the test drive number of the floppy disk drive to be tested and press Enter.
Test drive number select (1:FDD#1,2:FDD#2,0:FDD1&2 ) ?
2. Select the media type of the floppy disk in the test drive to be tested, and pressEnter.
Media in drive #X mode (0:2DD ,1:2D,2:2D-2HD/2DD,3:2HD) ?
3. Select the track you want the test to start on and press Enter.
Test start track (Enter :0/dd:00-79) ?
4. The floppy disk test menu will appear after you select. Select the number of thesubtest you want to execute and press Enter. The following message will appear during the floppy disk test.
3-20
File No. 960-140 Subtest 01 Sequential read This subtest performs a Cyclic Redundancy Check (CRC) that continuously reads all the tracks on a floppy disk. The following tracks are read according to the media type in the floppy disk drive: Double-sided, double-density (2D): Tracks 0 to 39. Double-sided, double-density, double-track (2DD) and doublesided, high-density, double-track (2HD): Tracks 0 to 79. The start track is specified when the FDD test is started from the Diagnostic Test Menu. Refer to Step 3 at the beginning of this section to set the start track. Subtest 02 Sequential read/write This subtest continuously writes data pattern B5ADADh to all the specified tracks selected in subtest 01. The data is then read and compared to the original data. Subtest 03 Random Address/Data This subtest writes random data to random addresses on all tracks defined in subtest 01. The data is then read and compared to the original data. Subtest 04 Write Specified Address This subtest writes specified data to a specified track, head, and address. Subtest 05 Read Specified Address This subtest reads data from a specified track, head, and address.
3-21
File No. 960-140
3.9
Printer Test
To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The Printer Test contains three subtests that test the output of the printer connected to the computer. The following messages will appear after selecting the Printer Test. Answer each of the questions with an appropriate response to execute the test. NOTE: An IBM compatible printer must be connected to the system to execute this test. The following message will appear when the printer test is selected:
channel#2 = XXXXh channel#3 = XXXXh Select the channel number (1-3
) ?
The printer I/O port address is specified by the XXXXh number. The computer supports three printer channels. Select the printer channel number and press Enter to execute the selected subtest. Subtest 01 Ripple pattern This subtest prints characters for codes 20h through 7Eh line-by-line while shifting one character to the left at the beginning of each new line.
3-22
File No. 960-140 Subtest 02 Function This subtest is for IBM compatible printers and tests the following functions: Normal print Double-width print Compressed print Emphasized print Double-strike print All characters print This subtest prints the various print types shown below:
Subtest 03
Wraparound NOTE: To execute this subtest, a parallel port wraparound connector must be connected to the computers printer port. The connectors (34M741986G01) wiring diagram is shown in Appendix F. This subtest checks the output and bi-directional modes of the data control and status lines through the parallel port wraparound connector.
3-23
File No. 960-140
3.10
Async Test
To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The async test contains seven subtests that test the asynchronous communication functions. Move the highlight bar to the subtest you want to execute and press Enter. The Subtests require the following data format: Method: Speed: Asynchronous 9600BPS (Subtests 01 to 04) 38400BPS (Subtests 06, 07) Data: 8 bits and one parity bit (EVEN) Data pattern: 20h to 7Eh The following message will appear at the bottom of the screen when subtests 01, 02, 03, 06, and 07 are selected:
Channel#1 = XXXXh Channel#2 = XXXXh Channel#3 = XXXXh Select the Channel number (1/2/3)
The serial I/O port address is specified by the XXXXh number. Select the serial port channel number and press Enter to start the subtest. Subtest 01 Wrap around (board) NOTE: To execute this subtest an RS-232C wraparound connector (34M741621G01) must be connected to the RS-232C port. The RS-232C wraparound connector wiring diagram is described in Appendix F. This subtest checks the data send/receive function through the wraparound connector. Subtest 02 Point to point (send) NOTE: To execute this subtest, two machines must be connected with an RS-232-C direct cable. One machine should be set as send(subtest 02) and the other set as receive (subtest 03). The wiring diagram for the RS-232-C direct cable is shown in Appendix F. This subtest sends 20h through 7Eh data to the receive side, then receives the sent data and compares it to the original data.
3-24
File No. 960-140 Subtest 03 Point to point (receive) This subtest is used with subtest 02 described above. This subtest receives the data from the send side, then sends the received data. Subtest 04 Interrupt test This subtest checks the Interrupt Request Level of IRQ 4, 3 and 5 from the send side. Subtest 06 FIR/SIR Point to point (send) NOTE: To execute subtests 06 and 07, each computer must have access to the other computers infrared port. This subtest sends 20h through 7Eh data to the receive side, then receives the sent data and compares it to the original data through the SIR port. Subtest 07 FIR/SIR Point to point (receive) This subtest is used with subtest 06 described above. This subtest receives the data from the send side, then sends the received data through the SIR port. NOTE: Select subtest numbers ,06 and 07. The following message will appear: Select the UIRCC mode (1:FIR /2:SIR)? 1: FIR mode 2: SIR mode
3-25
File No. 960-140
3.11
Hard Disk Test
To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter, and follow the directions on the screen. The hard disk test contains ten subtests that test the hard disk drive functions. NOTE: The contents of the hard disk will be erased when subtest 02, 03, 04, 05, 06, 08, 09, or 10 is executed. Before running the test, the customer should transfer the contents of the hard disk to floppy disk. If the customer has not or cannot perform the back-up, create back-up disks as described below. Check to see if the Microsoft Create System Disks Tools (MSCSD.EXE) still exists in the System Tools Folder. (This tool can be used only once.) If it exists, use it to back up the pre-installed software, then use the Backup utility in the System Tools folder to back up the entire disk, including the users files. Refer to the operating system instructions. The following messages will appear after selecting the hard disk test from the DIAGNOSTIC TEST MENU. Answer each of the questions with an appropriate response to execute the test:
[HDD test parameters] Test drive number :#1 HDC F/W error retry :yes Data compare error dump :no Detail status display :no :Select items, Enter:Finish, Esc:Exit,F5:Set default
1. Select the hard disk drive number to be tested:

Test drive number HDD#1 HDD#2 HDD1&2
2. This message is used to select the retry operation when the hard disk controller detects an error. Select yes or no.
HDC F/W error retry yes no
3. This message is used to select the error dump operation when a data compare error is detected. Select yes or no:
Data compare error dump yes no
3-26
File No. 960-140 4. This message is used to select whether or not the HDD status is displayed on the screen. The HDD status is described in section 3.19. Select yes or no:
Detail status display yes no
5. This message is used to select whether or not the HDD status is displayed on the screen. The HDD status is described in section 3.19. Select 1 or 2 and press Enter. 6. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press Enter. The following message will appear during each subtest.
HARD DISK TEST XXXXXXX
SUB- TEST : XX PASS COUNT: XXXXX ERROR COUNT: XXXXX WRITE DATA: XX READ DATA : XX ADDRESS : XXXXXX STATUS : XXX
The first three digits of the ADDRESS indicate which cylinder is being tested, the fourth digit indicates the head and the last two digits indicate the sector. The first digit of the STATUS number indicates the drive being tested and the last two digits indicate the error status code as explained in Table 3-2. Subtest 01 Sequential read This subtest is a sequential reading of all the tracks on the HDD starting at track 0. When all the tracks on the HDD have been read, the test starts at the maximum track and reads the tracks on the HDD sequentially back to track 0. Subtest 02 Address uniqueness This subtest writes unique address data to each sector of the HDD track-bytrack. The data written to each sector is then read and compared with the original data. There are three ways the HDD can be read: Subtest 03 Forward sequential Reverse sequential Random
Random address/data This subtest writes random data to random addresses on the HDD cylinder, head and sector. This data is then read and compared to the original data.
3-27
File No. 960-140 Subtest 04 Cross talk & peak shift This subtest writes eight types of worst pattern data (listed below) to a cylinder, then reads the data while moving from cylinder to cylinder.
Worst pattern data
B5ADAD 4A5252 EB6DB6 149249 63B63B 9C49C4 2DB6DB D24924
Cylinder
0 cylinder 1 cylinder 2 cylinder 3 cylinder 4 cylinder 5 cylinder 6 cylinder 7 cylinder
Subtest 05
Write/read/compare (CE) This subtest writes B5ADADh worst pattern data to the CE cylinder on the HDD, then reads the data from the CE cylinder and compares it with the original data.
Subtest 06
Write specified address This subtest writes specified data to a specified cylinder and head on the HDD.
Subtest 07
Read specified address This subtest reads data which has been written to a specified cylinder and head on the HDD.
Subtest 08
ECC circuit This subtest checks the Error Check and Correction (ECC) circuit functions of the specified cylinder and head on the HDD.
Subtest 09
Sequential write This subtest writes specified 2-byte data to all of the cylinders on the HDD.
Subtest 10
W-R-C specified address This subtest writes data to a specified cylinder and head on the HDD, then reads the data and compares it to the original data.
3-28
File No. 960-140

3
3.12
Real Timer Test
To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The real timer test contains three subtests that test the computers real timer functions. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Real time A new date and time can be input during this subtest. To execute the real time subtest follow these steps: 1. Select subtest 01 and the following message will appear:
Current date : XX-XX-XXXX Current time : XX:XX:XX Enter new date: PRESS [ENTER] KEY TO EXIT TEST
2. If the current date is not correct, input the correct date at the Enter new date prompt and press Enter. The following prompt will appear:
Enter new time :
3. If the current time is not correct, input the correct time in 24-hour format. Pressing Enter toggles between the time and the date. To exit, press Ctrl + Break. Subtest 02 Backup memory This subtest performs the following backup memory check:
Writes 1-bit of on data to address 01h through 80h Writes 1-bit of off data to address 0Eh through 80h Writes the data pattern AAh and 55h to the RTC 114-byte memory (address 0Eh to 7Fh)
The subtest then reads and compares this data with the original data.
To exit, press Ctrl + Break.
3-29
File No. 960-140 Subtest 03 Real time carry
CAUTION: When this subtest is executed, the current date and time are erased. This subtest checks the real time clock increments, making sure the date and time are displayed in the following format:
Current date Current time : : 12-31-19 95 23:59:58
Pressing Enter displays the following

Current date : Current time : 01-01-1996 00:00:00
PRESS [Enter] KEY TO EXIT TEST
Press Ctrl + Break to exit.
3-30
File No. 960-140
3.13
NDP Test
To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The NDP test contains one subtest that tests the computers NDP functions. Subtest 01 NDP This test checks the following functions of the coprocessor: Control word Status word Bus Addition Multiplication Press Ctrl + Break to exit.
3-31
File No. 960-140
3.14
Expansion Test
To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE: Subtest 01 To execute this subtest, the PC card wraparound connector is required. PCMCIA wrap around This test checks the following signal line of the PC card slot: Address line REG#, CE#1, CE#2 line Data line Speaker line Wait line BSY#, BVD1 line This subtest is executed in the following order:
Sub# 01 Address 00001 00001 00002 00003 00004 00005 Good nn nn ww
Bad xx xx rr
Contents Address line REG#, CE#1, CE#2 nn=A0, 90, 80, 00 Data line ww=write data, rr=read data Speaker line Wait line (40<xx<80) Other lines (BSY#, BVD1) NN=21, 00
02 03 04 05
40,80 nn
xx xx
NOTE: Select the subtest number01the following message will appear: Test slot number select (1:slot0, 2:slot1, 0:slot0&1) ?
3-32
File No. 960-140
NOTE: Subtests 02 and 04 are for Enhanced Port Replicator . For procedures on those subtests, refer to Enhanced Port Replicator manual.
Subtest 03
RGB monitor ID test Connect a wrap around Board to the external monitor port to test the RGB monitor ID.
Subtest 06
ZV Port wrap around Use the PC Card/ZV Test Card (Rev.B or higher) to conduct the test. The video and audio interfaces will be tested. When the video test is initiated, the board automatically writes data AAAAh and 5555h alternately to address A000:0000h. The data written first is determined randomly, and has no effect on the validity of the test. After the video test is run the audio interface is tested. The test emits 1kHz sine wave sound on the left speaker and 2kHz sine wave sound on the right speaker.
3-33
File No. 960-140
3.15
Sound Test
To execute the sound test, select 12 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The sound test contains four subtests that test the computers sound functions. NOTE: To execute this subtest, the internal microphone and internal headphone (or internal speaker) are required. The system is capable of producing high volume sound, so when you use the headphones be careful to set the volume low and adjust it as necessary. Using the headphones at full volume could damage your ears. Subtest 01 CODEC (REC/PLAY) Test the functions of the Codec (AD1848) A/D, D/A converter. Test the microphone terminals and headphone terminals at the same time. When you execute this subtest the following message displays.
[Quick REC & PLAY for AD1848] Press any key to *** REC ***
After pressing any key, start recording and immediately play the sound. (It takes three seconds.) Subtest 02 FM Synthesizer Test the OPL3 (YMF262) functions. Connect the headphone and check the scale on the right and left sides. Also check the sound adjustment volume. Subtest 03 SIN Wave Playback This subtest expands the sine wave data table to 64KB and creates sine wave data. The play data is transferred between DMA and CODEC, and plays the sound. (It is a long beep.) Also, using the oscilloscope, observe the sine waveform.
3-34
File No. 960-140
3.16
Error Code and Error Status Names
Table 3-2 lists the error codes and error status names for the Diagnostic Test. Table 3-2 Error codes and error status names (1/3)
Device name (Common) System Error code FF 01 02 03 01 02 14 DD DE DF 01 02 03 04 06 08 09 10 20 40 60 80 EE FF 01 02 03 04 05 06 01 08 10 20 40 80 Error status name Data Compare Error ROM Checksum Error Location ID error Serial ID Write error Parity Error Protected Mode Not Changed Memory Read/Write Error Cache Memory Error 2nd Cache Error TAG-RAM Error Bad Command Address Mark Not Found Write Protected Record Not Found Media Removed DMA Overrun Error DMA Boundary Error CRC Error FDC Error Seek Error Not Drive Error Time Out Error Write Buffer Error Data Compare Error Mouse interface error IPS interface error Interface error Retransmi error Mouse handler not support PS/2 mouse & IPS not support Time Out Fault Select Line Out Of Paper Power Off Busy Line
Memory
FDD
Keyboard
Printer
3-35
File No. 960-140 Table 3-2 Error codes and error status names (2/3)
Device name ASYNC Error code 01 02 04 08 10 20 40 50 60 70 80 88 01 02 04 05 07 08 09 0A 0B 10 11 20 40 80 AA BB CC EO EE DA C1 C2 C3 C4 C5 C6 C7 C8 CB CD 01 02 03 04 05 06 Error status name [DSR On] Time Out [CTS On] Time Out [RX READY] Time Out [TX FULL] Time Out Parity Error Framing Error Overrun Error Underrun error Timer time out error CRC error Line Status Error Modem Status Error Bad Command Error Address Mark Not Found Record Not Found HDC Not Reset Error Drive Not Initialized HDC Overrun (DRQ) DMA Boundary Error Bad Sector Bad Track Error ECC Error ECC Recover Enable HDC Error Seek Error Time Out Error Drive Not Ready Undefined Error Write Fault Status Error Access Time Out Error No HDD ADDRESS Line error REG# Line error CE#1 Line error CE#2 Line error DATA Line error WAIT Line error BSY# Line error BVD1 Line error ZV Port error No PCMCIA No Co-Processor Control Word Error Status Word Error Bus Error Addition Error Multiply Error
HDD
Expansion
NDP
3-36
File No. 960-140 Table 3-2 Error codes and error status names (3/3)
Device name PCMCIA Error code C1 C2 C3 C4 C5 C6 C7 C8 CB CD Error status name Address Line Error REG# Line Error CE#1 Line Error CE#2 Line Error DATA Line Error WAIT Line Error BSY# Line Error BVD1 Line Error ZV Port Error No PCMCIA
3-37
File No. 960-140
3.17
Hard Disk Test Detail Status
When an error occurs in the hard disk test, the following message displays:
HDC status = XXXXXXXX
Detailed information about the hard disk test error displays on the screen by an eight-digit number. The first four digits represent the hard disk controller (HDC) error status number and the last four digits are not used. The hard disk controller error status is composed of two bytes; the first byte displays the contents of the HDC status register in hexadecimal form and the second byte displays the HDC error register. The contents of the HDC status register and error register are listed in Tables 3-3 and 3-4. Table 3-3 Hard disk controller status register contents
Bit 7 6 5 4 3 2 1 0 BSY (Busy) DRDY (Drive ready) DWF (Drive write fault) DSC (Drive seek complete) DRQ (Data request) CORR (Corrected data) IDX (Index) ERR Error Name 0 HDC is ready. 1 HDC is busy. 0 Hard disk drive is not ready to accept any command. 1 Hard disk drive is ready. 0 DWF error is not detected. 1 Write fault condition occurred. 0 The hard disk drive heads are not settled over a track. 1 The hard disk drive heads are settled overa track. 0 Drive is not ready for data transfer. 1 Drive is ready for data transfer. 0 Not used 1 Correctable data error is corrected. 0 Not used 1 Index is sensed. 0 Normal 1 The previous command was terminated with an error. Description
3-38
File No. 960-140 Table 3-4 Error register contents

Bit 7 6 5 4 3 2 1 Name BBK1 (Bad block mark) UNC (Uncorrectable) IDNF (Identification) ABRT (Abort) TK00 (Track 0) 0 Description 0 Not used 1 A bad block mark is detected. 0 There is no uncorrectable data error. 1 Uncorrectable data error has been detected. Not used 0 Not used 1 There was no ID field in the requested sector. Not used 0 Not used 1 Illegal command error or a drive status error occurred. 0 The hard disk found track 0 during a recalibrate command. 1 The hard disk could not find track 0 during a recalibrate command. Not used.
3-39
File No. 960-140
3.18
Hard Disk Format
This command executes hard disk formatting. There are two types of hard-disk formatting: Low-level (physical) formatting MS-DOS (logical) formatting The hard disk format function performs a low-level format of the hard disk and executes the following hard disk formats and check: 1. 2. 3. 4. All track FORMAT Good track FORMAT Bad track FORMAT Bad track CHECK The contents of the hard disk will be erased when the program executes. Before running the test, the customer should transfer the contents of the hard disk onto a floppy disk. If the customer has not or cannot perform the backup, create backup disks as described below. Check to see if the Microsoft Create System Disks Tools (MSCSD.EXE) still exists in the System Tools Folder. (This tool can be used only once.) If it exists, use it to back up the preinstalled software, then use the Backup utility in the System Tools folder to back up the entire disk, including the users files. Refer to the operating system instructions.
NOTE:
3-40
File No. 960-140
3.18.1
Function Description
1. All Track FORMAT This option performs a low-level format of all the tracks on the hard disk as listed in Table 3-5 below: NOTE: Before executing the all track format option, check for bad tracks using the Bad Track CHECK option or display a list of bad tracks on the HDD. Table 3-5 Hard disk formatting sequence
Items Storage capacity Formatted (Bytes) Cylinders Heads Sectors Bytes per sector Rotation speed (rpm) Recording method IBM DYKA-22160 2,167,603,200 4,200 16 63 512 4,200 8-9 RLL IBM DYKA-23240 3,253,469,184 6,304 16 63 512 4,200 8-9 RLL
2. Good Track FORMAT This option formats a specified cylinder and track as a good track. If a good track is formatted as a bad track, use this option to change the track to a good track. 3. Bad Track FORMAT This option formats a specified cylinder and track as a bad track. If a bad track is detected, use this option to label it as a bad track. 4. Bad Track CHECK This option searches the hard disk for bad tracks by reading data to all the tracks on the hard disk. A list of bad tracks displays when the program is complete. If an error other than a bad track is detected, the program is automatically terminated.
3-41
File No. 960-140
3.18.2
Operations
NOTE: After the HDD has been formatted, execute the Toshiba MS-DOS FDISK command to partition the HDD. Execute the Toshiba MS-DOS FORMAT command. Refer to the Toshiba MS-DOS manual for more information about using these commands. Selecting TEST 2 and pressing Enter in the DIAGNOSTIC MENU, displays the following messages:
DIAGNOSTICS - HARD DISK 1 2 3 4 9 All track FORMAT Good track FORMAT Bad track FORMAT Bad track CHECK Go to TEST MENU FORMAT : VX.XX
: Select items, Enter: Finish, Esc: Exit 1. All Track FORMAT Pressing 1 selects All track FORMAT, which lets you format the entire disk.
[All track FORMAT] Drive: Cylinder Head: Sector: #1 = HDD : XXXX XX XX >>> #2 = Non
<<< Model name =
The following selections also appear at the bottom of the screen in succession:
Drive number select (1 :#1,2:#2) ?
(a) Select a drive number and press Enter. The following message will appear:
Interleave number (1/1 ~ 8 ) ?
(b) Select an interleave number, 1 ~ 8 and press Enter. Pressing only Enter selects 1.
3-42
File No. 960-140 (c) Bad track register The Bad Track register prompt will appear as shown below. Enter the cylinder and head numbers of bad tracks and press Enter. Note that if there are no bad tracks, pressing Enter alone is the same as executing All Track Format described in item (d) below.
[ WARNING: Current DISK data will be completely destroyed ] Press Bad cylinder number ( dddd)] key ? Press Bad head number ( dd)] key ?
Enter the cylinder and head number in the format above in decimal notation. Repeat for each bad track you want to format. After entering the bad tracks, press Enter to execute the format. (d) All track format All tracks are formatted as good tracks except those registered as bad tracks in item (c) above or those identified as bad tracks in track verification described in item (e) below. (e) Track verification A check is made of all tracks and if an ECC error, ECC-correctable-data error or record-not-found error is detected at a track, that track is formatted as a bad track automatically. 2. Good Track FORMAT If a good track has been erroneously formatted as a bad track, you can use this subtest to reformat the track as a good track. To format a track as a good track, enter the number for the drive, interleave, cylinder and head as indicated in the screen prompt shown below.
Drive number select (1 :#1, 2:#2) ? Interleave number (1 / 1 - 8 ) ? Press [Cylinder number ( dddd) ] ? Press [Head number ( dd) ] ?
Press Enter to return to the Hard Disk Format menu.
3-43
File No. 960-140 3. Bad Track FORMAT To format a track as a bad track, enter the number for the drive, interleave, cylinder and head as indicated in the screen prompt shown below.
Drive number select (1 :#1, 2:#2) ? Interleave number (1 / 1 - 8 ) ? Press [Cylinder number ( dddd) ] ? Press [Head number ( dd) ] ?
Press Enter to return to the Hard Disk Format menu. 4. Bad Track CHECK This subtest reads the entire disk and displays a list of bad tracks. The test is terminated in case of a bad track check error. To initiate the subtest enter the drive number at the prompt shown below.
Drive number select (1 :#1, 2:#2) ?
Bad tracks will be displayed in the format shown below. [[cylinder, head = 0123 03]]
Press Enter to return to the Hard Disk Format menu.
3-44
File No. 960-140
3.19
Head Cleaning
3.19.1
This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.19.2 Operations
1. Selecting test 4 from the DIAGNOSTIC MENU and pressing Enter displays the following messages:
DIAGNOSTICS - FLOPPY DISK HEAD CLEANING : VX.XX
Mount cleaning disk(s) on drive(s). Press any key when ready.
2. Remove the Diagnostics Disk from the FDD, then insert the cleaning disk and press Enter. 3. When the cleaning start message appears, the FDD head cleaning has begun. 4. The display automatically returns to the DIAGNOSTIC MENU when the program is completed.
3-45
File No. 960-140
3.20
Log Utilities
3.20.1
This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk or output the data to a printer. If the power switch is turned off, the error information will be lost. The error information displays in the following order: 1. Error count (CNT) 2. Test name (TS-NAME) 3. Subtest number (TS-NAME) 4. Pass count (PASS) 5. Error status (STS) 6. FDD/HDD or memory address (ADDR) 7. Write data (WD) 8. Read data (RD) 9. HDC status (HSTS) 10. Error status name (ERROR STATUS NAME) 3.20.2 Operations
1. Selecting 5 and pressing Enter in the DIAGNOSTIC MENU logs error information into RAM or onto a floppy disk. The error information displays in the following format:
3-46
File No. 960-140
2. The error information displayed on the screen can be manipulated by the following number keys: The 1 key scrolls the display to the next page. The 2 key scrolls the display to the previous page. The 3 key returns to the Diagnostic Menu. The 4 key erases all error log information in RAM. The 5 key out puts the error log information to a printer. The 6 key reads the log information from a floppy disk. The 7 key writes the log information to a floppy disk. 3. In the case of error retry OK, a capital R will be placed at the beginning of the error status. However, it is not added to the error count.
3-47
File No. 960-140
3.21
Running Test
3.21.1
This function automatically executes the following tests in sequence: 1. 2. 3. 4. 5. 6. 7. 8. System test (subtest 01) Memory test (subtests 01, 02, 04, and 06) Display test (subtest 01 to 05) FDD test (subtest 02) HDD test (subtests 01 and 05) Real timer test (subtest 02) Printer test (subtest 03) if selected Async test (subtest 01) if selected
The system automatically detects the number of floppy disk drives connected to the computer for the FDD test. 3.21.2 Operations
NOTE: Do not forget to load a work disk in the FDD. If a work disk is not loaded, an error will be generated during the FDD testing. 1. Remove the diagnostics disk from the floppy disk drive and insert the work disk. 2. Select 6 from the Diagnostic Menu and press Enter, the following message displays:
Printer wrap around test (Y/N ) ?
Selecting Y (yes) executes the printer wraparound test. A printer wraparound connector must be connected to the parallel port of the computer to properly execute this test. 3. Select Y or N and press Enter. The following message will appear:
Serial #A wrap around test (Y/N ) ?
Selecting Y (yes) executes the ASYNC wraparound test. An RS-232-C wraparound connector must be connected to the serial port of the computer to properly execute this test.
3-48
File No. 960-140 4. Select Yes or No and press Enter. The following message will appear :
Mount the work disk(s) on the drive(s), then press [Enter] key. [Warning : The contents of the disk(s), will be destroyed.]
5. This program is executed continuously. To terminate the program, press Ctrl + Break.
3-49
File No. 960-140
3.22
Floppy Disk Drive Utilities
3.22.1
This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE: This program is only for testing a floppy disk drive. The option is different from the Toshiba MS-DOS FORMAT command. This program can format a 5.25-inch or 3.5-inch floppy disk in the following formats: (a) 2DD: Double-sided, double-density, double-track, 96/135 TPI, MFM mode, 512 bytes, 9 sectors/track. (b) 2HD: Double-sided, high-density, double-track, 96/135 TPI, MFM mode, 512 bytes, 18 sectors/track. 2. COPY This program copies data from a source floppy disk to a target floppy disk. 3. DUMP This program displays the contents of the floppy disk and the designated sectors of the hard disk on the display. 4. HDD-ID READ This program reads the hard disk ID and displays the hard disk ID, serial numberand others hard disk information.
3-50
File No. 960-140
3.22.2
Operations
1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message:
[ FDD UTILITIES ] 1 2 3 4 9 FORMAT COPY DUMP HDD ID EXIT TO DIAGNOSTICS MENU
2. FORMAT program (a) Selecting FORMAT displays the following message:

DIAGNOSTICS - FLOPPY DISK FORMAT : VX.XX Drive number select (1:A, 2:B ) ?
(b) Select a drive number to display the following message:

Type select (0:2DD ,3:2HD) ?
(c) Select a media/drive type number and press Enter. A message similar to the one below will display:
Warning : Disk data will be destroyed. Insert work disk into drive A: Press any key when ready.
(d) Remove the Diagnostics Disk from the FDD, insert the work disk and press any key. The following message will display when the FDD format is executed:
[ FDD TYPE ] : TRACK = XXX [ FDD TYPE ] : HEAD = X [ FDD TYPE ] : SECTOR = XX Format start [[track, head = XXX X]]
After the floppy disk is formatted, the following message will appear:
Format complete Another format (1:Yes/2:No ) ?
(e) Typing 1 displays the message from step (c) above. Typing 2 returns the test to the DIAGNOSTIC MENU.
3-51
File No. 960-140 3. COPY program (a) When COPY is selected, the following message appears:
FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD ,3:2HD) ?
(b) Selecting a media/drive type number will display a message similar to the one below:
Insert source disk into drive A: Press any key when ready.
(c) Remove the Diagnostics Disk from the FDD, insert the source disk and press any key. The following message will appear, indicating the program has started.
[ FDD TYPE ] : TRACK = XXX [ FDD TYPE ] : HEAD = X [ FDD TYPE ] : SECTOR = XX Copy start [[ track,head = XXX X ]]
(d) Remove the source disk from the FDD, insert a formatted work disk and press any key. The [[ track, head = XXX X ]] message will appear and start copying to the target disk. When the amount of data is too large to be copied in one operation, the message from step (b) displays again. After the floppy disk has been copied, the following message will appear:
Copy complete Another copy (1:Yes/2:No ) ?
(e) To copy another disk, type 1 and the message from step (a) displays again. Entering 2 returns the test program to the DIAGNOSTIC MENU.
3-52
File No. 960-140 4. DUMP program (a) When DUMP is selected, the following message appears:
DIAGNOSTICS-HARD DISK & FLOPPY DISK Drive type select (1:FDD, 2:HDD ) ? DUMP : VX.XX
(b) Select a drive type. If 1 is selected in step (a), the following message displays.
Select drive number (1:A, 2:B ) ?
Select an FDD drive number. The display will go to step (c). If 2 is selected in step (a), the following message displays:
Select drive number (1:C, 2:D ) ?
After selecting the HDD, the display will go to step (f). (c) The following message will display:
Format type select (1:2DD ,3:2HD) ?
(d) Select a format type. The following message will appear:

Insert source disk into drive A: Press any key when ready.
3-53
File No. 960-140 (e) Insert a source disk and press any key. (f) The following message will appear:
Max. [Track ] [ Head ] [Sector] address = XXXX = XX = XX
Track number ??
Set the track number you want to dump. The system will access the disk and dump a list. 5. HDD ID program Selecting HDD ID displays the following HDD ID configuration:
[HDD ID Read (VX.XX)] [Drive #X] ID code (h) = XXXX No. of Cylinders = XXXX XXXX Removable Cylinders = XXXX XXXX No. of Heads = XXXX XXXX Unformat Bytes/Track = XXXX XXXX Unformat Bytes/Sector = XXXX XXXX Sectors/Track = XXXX XXXX Gap Length = XXXX XXXX Sync. Bytes = XXXX XXXX Reswrved (h) = XXXX Serial No. = YYY... Controller Type (h) = XXXX Sector Buffers = XXXX XXXX ECC Bytes = XXXX XXXX Firmware Rev. = YYYYYY.. Model No. = YYYY... Reserved (h) = XXXX Double Word Capability = XXXX XXXX Press [Enter] key
Press Enter to return to the FDD UTILITIES MENU.
3-54
File No. 960-140

3
3.23 System Configuration
3.23.1 Function Description The System Configuration program contains the following configuration information for the computer: 1. Processor Type 2. VGA Controller 3. MS-DOS Version 4. BIOS ROM Version (1st ID, 2nd ID) 5. Boot ROM Version 6. KBC Version 7. PS Microprocessor Version 8. Total Memory Size 9. Sound System 10. The number of printer ports 11. The number of ASYNC ports 12. The number of math co-processor 13. PCMCIA Slot 14. Modem Type 15. The number of floppy disk drives 16. The number of hard disk drives 17. Selectbay Unit 18. Date/Time
3-55
File No. 960-140
3.23.2 Operations Selecting 8 from the DIAGNOSTIC MENU and pressing Enter displays the following system configuration:
System Configration Display : Ver X.XX [Machine Name ???] ** - Processor Type = XXXX ** - VGA Controller = XXXX * - MS-DOS Version = VX.XX * - BIOS ROM Version = V .XX 1st ID = XXH, 2nd ID = XXH * - BOOT ROM Version = VX.XX * - KBC Version = VX.XX * - PS Micom Version = VX.XX (EC Version = VX.XX) * - Total Memory Size = XXXXXMB( Converntional Memory = XXXXX KB) ** * * * * * * * Sound System = X Prin ter Adapter X ASYNC Adapter X Math Co-Processor X PCMCIA Slot X Modem + DAA = X Floppy Disk Drive(s) X Hard Dis k Drive(s) XXXXX LPT1 = XXXX COM1 = XXXX XX Track = XXXXX, Head = XX, Sector = XX #1 Cylinder = XXXXX, Head = XX, Sector =XX #2 Cylinder = XXXXX, Head = XX, Sector =XX * Selective Bay Unit = XXXX LPT2 = XXXX COM2 = XXXX LPT3 = XXXX COM3 = XXXX
Press [Enter] Key
[Date = XXXX-YY-ZZ, XX :YY:ZZ]
Press Enter to return to the DIAGNOSTIC MENU.
3-56
File No. 960-140
3.24 SETUP
3.24.1 Function Description This program displays the current system setup information as listed below: 1. Memory (a) Total 2. Password 3. Peripheral (a) Pointing Devices (b) Parallel Port Mode (c) Hard Disk Mode 4. Boot Priority 5. Display (a) Power On Display CPU Cache (b) LCD Display Stretch 6. Others (a) (b) (c) (d) (e) (f) Power-up Mode CPU Cache Auto Power On Alarm Volume System Beep Panel Power On/Off
7. Configuration 8. I/O Ports (a) Serial (b) Parallel (c) Sound 9. Display 10. PCI Bus 11. PC Card 12. Floppy Disk I/O
3-57
File No. 960-140
3.24.2 Accessing the SETUP Program Selecting 0 from the DIAGNOSTICS MENU and pressing Enter displays the TSETUP screen. The TSETUP screen is divided into two pages: SYSTEM SETUP (1/2)and SYSTEM SETUP (2/2) .
NOTE: The Panel Power On/Off item and the System Auto Off item appears when the computer is in Resume mode and Hibernation mode.
3-58
File No. 960-140
Moving Within the SETUP Menu and Changing Values 1. Press and to move between the two columns. Press PgDn and PgUp to move between the two pages. Press and to move between items in a column. 2. Press either the space bar or BkSp to change the value. Accepting Changes and Exiting the SETUP Window 1. Press End to accept the changes you made. If the changed item does not require the system to reboot, the following message displays:
Are you sure? (Y/N)
If the changed item requires the system to reboot, the following message displays:
Are you sure? (Y/N)
The changes you made will cause the system to reboot.
2. To make other changes, press N. Repeat the steps above. 3. To accept the changes, press Y. NOTE: You can press Esc to quit at any time without saving changes. SETUP asks you to confirm that you do not want to save your changes. The Factory Preset Configuration When you access SETUP, the current configuration displays. 1. To show the factory preset configuration, press Home. 2. To accept the default settings, press End and then press Y. NOTE: When you execute the default setting, the following settings are not changed: HDD Mode Password Sound System: I/O Address, Interrupt Level, DMA Write Policy
3-59
File No. 960-140
SETUP Options The SETUP screen is divided into functionally related groups. This section describes each group and its options. 1. Memory This option displays the computers memory. (a) Total This field displays the total amount of memory installed and is automatically calculated by the computer. You cannot change this value. 2. Password This field enables or disables the internal video controller. Registered Not registered The user password has been registered. The user password has not been registered.
For details on setting the user password refer to the User's Manual. 3. Peripheral (a) Pointing Devices This option enables or disables the AccuPoint. Auto-Selected If a PS/2 mouse is connected to the computer when you turn on the power, the PS/2 mouse is enabled and the AccuPoint is disabled. Otherwise, the AccuPoint is enabled. (Default) Enables both the AccuPoint and PS/2 mouse or the AccuPoint and a mouse connected to USB port.
Simultaneous
3-60
File No. 960-140 (b) Parallel Port Mode This option in this tab are ECP and Standard Bi-directional. ECP Sets the port mode to Extended Capabilities Port (ECP). For most printers, the port should be set to ECP. (Default) This setting should be used with some other parallel devices.
Std. Bi-Direct. (c) Hard Disk Mode
Use this item to select the hard disk mode. Enhanced IDE (Normal) Standard IDE Select this mode when using MS-DOS. Windows for Workgroups, Windows 95 or OS/2. (Default) Select this mode when using Novell NetWare or UNIX. When this mode is selected, up to 504MB is logically available even though the disks capacity is larger than 504MB.
NOTE: Formats for Enhanced IDE and Standard IDE are different, so if you change the setting, you will have to reformat the hard disk for the appropriate setting. 4. Boot Priority Use this option to select the disk drive priority for boot up. FDD HDD: HDD FDD: The computer looks for bootable files first on the FDD and next on the HDD. (Default) The computer looks for bootable files first on the HDD and on the FDD.
You can reverse the order by holding down the F10 key while the computer is booting. This procedure alternates the setup setting.
3-61
File No. 960-140 5. Display (a) Power On Display This option is used to select the display when booting up. Auto-Selected Simultaneous (b) LCD Display Stretch LCD Display Stretch enables or disables a larger display area of the screen. Enabled Disabled Enables the LCD display stretch feature. Disables the LCD display stretch feature. (Default) Selects an external monitor if one is connected, otherwise it selects the internal LCD. (Default) Selects both the internal LCD and the external monitor for simultaneous display.
3-62
File No. 960-140 6. Others Whether you need to configure the computer with these options depends primarily on the kind of software or peripherals you use. (a) Power-up Modes Use this option to choose hibernation, resume and boot mode. Boot Resume Hibernation (b) CPU Cache Use this option to enable or disable the CPU cache. Enabled Disabled Enables the CPU cache. (Default) Disables the CPU cache. Turns on boot mode. (Default) Turns on resume mode. Turns on hibernation mode.
When enabled is selected, a subwindow similar to the one below displays to let you select the cache write policy. The options for this setting are Write-back (default) and Write-through for CPU cache.
Write-back policy provides better system performance, because main memory is accessed only when necessary to update the cache contents with changes in main memory. Write-through policy accesses main memory every time data is handled by the processor.
3-63
File No. 960-140 (c) Auto Power On Use this option to set a time and date for automatic power on the Alarm Date Option displays when Alarm Time is enabled.
Alarm Time is set in the sequence of hours and minutes. Seconds cannot be changed. Alarm Date Option is set in the sequence of month and day. If Alarm Date is set to Disabled, the computer will be powered on at the same time every day. Press to move the cursor to the right and to move the cursor to the left when you set the date and time.
3-64
File No. 960-140
(d) Alarm Volume This option disables or sets the volume level of the alarm. Setting this option to off disables the computers sound function for alarms. Off Low Medium High Disables the alarm. Sets the alarm volume to low. Sets the alarm volume to medium. Sets the alarm volume to high. (Default)
When Alarm Volume is selected, the subwindow below displays to enable or disable certain functions.
Enabled Disabled (e) Panel Power On/Off
Enables the feature. (Default) Disables the feature.
This option allows you to automatically turn your computer on or off by opening or closing the display panel. If this feature is enabled when the computer is in Resume or Hibernation mode, the system is automatically powered off when the display panel is closed, and powered on when the panel is opened. This option does not appear when the computer is in boot mode. Enabled Disabled Enables the feature. Disables the feature. (Default)
3-65
File No. 960-140 (f) System Auto Off Use this option to disable or set the duration of the system automatic off function in Resume or Hibernation mode. In Boot mode and Hibernation mode, it is disabled and does not display. Disabled xx Min. Disables system automatic power off. Automatically turns off power to the system if it is not used for the duration set. The duration xx can be set to 10, 20, 30, 40, 50 or 60 minutes.
7. Configuration This field displays the configuration method. You cannot change this value. All Devices
3-66
File No. 960-140 8. I/O ports This option controls settings for the serial and parallel ports and the sound system. NOTE: Do not assign the same interrupt request level and I/O address to the serial port and PC card. (a) Serial Use this option to set the COM level for the serial port. The serial port interrupt request level (IRQ) and I/O port base address for each COM level is shown below:
COM level COM1 COM2 COM3 COM3 COM3 COM4 COM4 COM4 Not Used Others Interrupt level 4 3 4 5 7 3 5 7 Disables the port Others settings made automatically by plug-and-play operating systems I/O address 3F8H 2F8H 3E8H 3E8H 3E8H 2E8H 2E8H 2E8H (Serial port default)
3-67
File No. 960-140 (b) Parallel This option sets the interrupt request level (IRQ) and I/O port base address for the parallel port. When the Printer Port Type is set to Standard Bidirectional, the options are:
LPT setting LPT 1 LPT 2 LPT 3 Not Used Others Interrupt level 7 5 7 Disables the port Others settings made automatically by plug-and-play operating systems I/O address 378H 278H 3BCH
When the Printer Port Type is set to ECP, the DMA channel can also be set to 1, 2 or 3. The default is 3.
LPT setting LPT 1 LPT 2 LPT 3 Not Used Others Interrupt level 7 5 7 Disables the port Others settings made automatically by plug-and-play operating systems I/O address 378H 278H 3BCH DMA channel 3 (Parallel port default) 3 3
When you select one of the above options, except for Not Used, a subwindow similar to the one below appears to let you set the DMA. The options for this setting are Channel 1 and Channel 3(default).
3-68
File No. 960-140 (c) Sound Use this option to enable or disable the sound system. Enabled Disabled Enables the sound system. (Default) Disables the sound system.
When Enabled is selected, a subwindow similar to the one below appears to let you set the WSS I/O address, SBPro I/O address, Synthesizer I/O address, WSS & SBPro & MPU401 IRQ Level, WSS (Play) DMA, WSS (Rec.) & SBPro DMA, Control I/O address, and MPU401 (MIDI I/F) for the sound system.
WSS I/O address Use this option to set the Windows Sound System I/O address from among the following settings:
530h (default), 540h, 550h, 560h
SBPro I/O address Use this option to set the Sound Blaster Pro I/O address from among the following settings:
220h (default), 240h, Others
Synthesizer I/O address You cannot change this value.
3-69
File No. 960-140
WSS & SBPro & MPU401 IRQ level This option sets the IRQ level for the Windows Sound System, Sound Blaster Pro and MPU401. The available settings are:
IRQ5 (default), IRQ7, IRQ9, IRQ11, IRQ15
WSS (Play) DMA This option sets the DMA channel for the Windows Sound System (playback). The available settings are:
Channel 0, Channel 1 (default), Channel 3
WSS (Rec.) & SBPro DMA This option sets the DMA channel for the Windows Sound System (recording) and Sound Blaster Pro. The available settings are:
Channel 0 (default), Channel 1, Channel 3
NOTE: When you set the WSS (Play) DMA and WSS (Rec.) & SBPro DMA option to the same channel, the WSS (Play) DMA option will display Same as Playback. Control I/O Address You cannot change this value. MPU401 (MIDI I/F) You cannot change this value. 9. Display (a) VGA Segment Address This option lets you set the VGA Segment Address C000h (Default) E400h
3-70
File No. 960-140 10. PCI Bus This option displays the interrupt request level for the CardBus in the computer. It is for information only and cannot be changed. 11. PC Card This option lets you set the PC Card Controller mode. Auto-Selected Card Bus/16 bit PCIC Compatible Use this setting for all PC Card if you are using Windows 95. (Default) If the card does not work properly with the AutoSelected setting, use this setting for Card Bus PC card. If the card does not work properly with the AutoSelected and CardBus/16 bit setting, use this setting for 16-bit PC Card.
12. Drives I/O This item display the installed hard disk drives: Built-in HDD or no drive. It appears only in TSETUP. Setting for Built-in HDD Primary IDE (1F0H/IRQ14) Not Used The built-in HDD is ready for use. Disables the built-in HDD.
3-71
File No. 960-140
3-72
File No. 960-140
Chapter 4 Replacement Procedures
File No. 960-140
4-ii
File No. 960-140
Chapter 4
4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13
Contents
Overview................................................................................................................4-1 HDD.......................................................................................................................4-8 Optional Memory Module.....................................................................................4-10 Keyboard..............................................................................................................4-12 Display Assembly..................................................................................................4-13 RTC Battery.........................................................................................................4-17 System Board, Heat Sink and PC Card Slot..........................................................4-18 Display Mask........................................................................................................4-20 FL Inverter Board.................................................................................................4-22 LCD Module ........................................................................................................4-24 Speaker, Power Switch Board and AccuPoint Board.............................................4-27 LCD Flexible Cable and Microphone.....................................................................4-30 I/O Adapter Board................................................................................................4-35
Figures Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 4-9 Figure 4-10 Figure 4-11 Figure 4-12 Figure 4-13 Figure 4-14 Removing the HDD cover...........................................................................4-8 Removing the HDD.....................................................................................4-9 Removing the HDD bracket ........................................................................4-9 Removing the keyboard brace....................................................................4-10 Lifting up the keyboard .............................................................................4-10 Removing the optional memory module.....................................................4-11 Removing the keyboard.............................................................................4-12 Removing the metal cover.........................................................................4-13 Removing the display flexible cable............................................................4-14 Removing five screws................................................................................4-14 Removing the display assembly..................................................................4-15 RTC battery removal.................................................................................4-17 Removing the system board.......................................................................4-18 Removing the heat sink .............................................................................4-19
4-iii
File No. 960-140 Figure 4-15 Figure 4-16 Figure 4-17 Figure 4-18 Figure 4-19 Figure 4-20 Figure 4-21 Figure 4-22 Figure 4-23 Figure 4-24 Figure 4-25 Figure 4-26 Figure 4-27 Figure 4-28 Figure 4-29 Figure 4-30 Figure 4-31 Figure 4-32 Removing the PC card slot........................................................................4-19 Removing the mask seals...........................................................................4-20 Removing the display mask .......................................................................4-21 Removing the FL inverter board................................................................4-22 Disconnecting the display cable .................................................................4-23 LCD module removal................................................................................4-25 Removing the speaker ...............................................................................4-27 Removing the power switch board.............................................................4-28 Removing the AccuPoint board.................................................................4-28 Removing the LCD module.......................................................................4-30 Removing tape ..........................................................................................4-31 Removing one screw and plastic support...................................................4-31 Removing the left top cover brace and microphone....................................4-32 Removing the LCD flexible cable...............................................................4-32 Removing the LCD cable...........................................................................4-33 Removing nine screws...............................................................................4-35 Removing the upper cover.........................................................................4-36 Removing the I/O adapter board................................................................4-36
4-iv
File No. 960-140
4.1
Overview
The disassembly and replacement procedures for units that can be replaced in the field (FRUs) are described in this section. It may not be necessary to remove all the FRUs in order to replace one FRU. The chart below shows a guideline on which FRUs are to be removed before removing a certain FRU. Be sure to remove the battery pack first. In repairing an FRU suspected to be the cause of a computer malfunction, determine FRUs to be removed according to the flow of the chart below.
The example at the right shows FRUs to be removed for the display assembly and for the FL inverter board. The display assembly is overlapped by the keyboard, which is overlapped by the optional memory module, HDD and battery pack/optional PC card. The FL inverter board is overlapped by the display mask and battery pack/optional PC card.
4-1
File No. 960-140
Before Beginning Work Observe the following before beginning work. All procedures must begin with the removal of the AC adapter, battery pack and any PC cards. 1. Do not disassemble the computer unless a malfunction occurs. 2. Use the specified tools. 3. Use and storage require a work environment free of the following. Dust and pollutants Static electricity Extremely high or low temperature or humidity
4. Conduct the diagnostic test described in Chapter 2 of this manual to identify which FRU is the cause of the malfunction. 5. Do not perform unnecessary operations. Observe the disassembly and installation procedures described in this manual. 6. The parts removed from the computer must be kept at a safe place away from the computer, free of damage and not impeding the work. 7. Many screws are removed and parts are replaced in disassembling the computer. Keep the screws in a safe place in such a way that you will be able to easily identify which screw belongs to which part. 8. Use the specified screws and mount the parts in the specified positions in reassembling the computer. Screw sizes are shown with explanations in the figures. 9. Be careful not to be injured by the many sharp edges and angles of the screws. 10. After replacing the FRU, check its operation and make sure that the computer operates normally. 11. Proceed chapter 4.2 or more after removing all items which are described in this section except otherwise noted.
4-2
File No. 960-140
Disassembly Procedures There are two basic types of cable connectors. Pressure plate connector Normal pin connector To disconnect the cable from a pressure plate connector, lift the tab on either side of the plastic pressure plate of the connector, and gently pull the cable out from the connector. To connect the cable to a pressure plate connector, lift the pressure plate high enough and slide the cable into the connector. Push the pressure place at both ends so the plate and connector will be at the same height, then fasten the cable at the correct position. Hold the cable, gently pull it, and make sure that the cable is securely in place. If the cable slips out of the connector, make that the pressure plate is lifted high enough, and connect the cable again. Standard pin connectors are used for all other cables. The cables can be connected to and disconnected from these connectors by simply pulling or pushing. Reassembly Procedures To reassemble the computer after disassembling it and repairing the parts that caused its malfunction, observe the general instructions given below. Take time and reassemble it properly as instructed. Hasty work often raises problems. Check that the cables and connectors are securely fastened. Before mounting the FRUs and other parts, check that the cables are not caught by screws or FRUs. Check that all the latches are correctly closed. Check that all FRUs have been fastened securely with all the screws. If the wrong screws are used, it may result in damage to the screw threads and heads or the FRUs may not be fixed securely. After repairing, put all items which are removed from target machine. After mounting the FRUs back in position, check that the computer operates normally.
4-3
File No. 960-140
Tools and Devices It is important for the safety of the workers and others in the neighborhood to use electrostatic discharging (ESD) devices. Proper use of these devices will raise the success rate of repairs and reduce the expenses arising from damage and breakdown of the parts. The following are necessary for disassembly and reassembly. 2-mm Philips screwdriver Tweezers (for easy removal of screws) ESD mat (to be placed on the work bench or floor) ESD wrist strap or heel grounder Anti-static carpet or floor Screw Tightening Torques Observe the following torques in tightening the screws. Overtightening may cause damage to the parts or screws, and undertightening may lead to a shortcircuit or other damage from loose screws or parts. M2 (2 mm) M2.5 (2.5 mm) HDD screw (M3) M3 (3 mm) Thin-head M2.5 screw Super thin-head M2.5 screw 0.22 N.m (2.2 kgf.cm) 0.36 N.m (3.5 kgf.cm) 0.3 N.m to 0.28 N.m (3.1 kgf.cm to 2.9 kg.cm) 0.49 N.m (5.0 kgf.cm) 0.22 N.m (2.2 kgf.cm) 0.22 N.m (2.2 kgf.cm)
4-4
File No. 960-140
Removing the Battery Pack To remove the battery pack follow the steps below. 1. Switch the computer off. Disconnect the AC adapter and any other external devices from the computer. 2. Turn the computer upside down. 3. Slide the battery release latch to the left to unlock the battery.
4. Slide the battery out.
CAUTION: Do not short the battery pack terminals or the terminals of the personal computer to which the battery pack is to be connected. When carrying the battery pack in a bag, for example, wrap it with vinyl sheet or the like to prevent the battery pack terminals from contact with metal objects. If the terminals short, they may become heated or develop a fire. Do not heat, disassemble, or short the battery pack. Do not throw it into fire. Otherwise, the battery pack may explode or cause a fire. Before storing the battery pack, cover the terminals with insulation tape or the like to prevent shorting. Exposed terminals may cause explosion or fire during storage.
4-5
File No. 960-140
Installing the Battery Pack To install the battery pack, observe the following instructions. WARNING: Use only batteries recommended by Toshiba. Installation of the wrong battery could cause the battery to explode and cause injury or other damage. 1. Switch the computer off. Disconnect the AC adapter and all external devices from the computer. 2. Align the battery with the guide rails. 3. Push the battery into position. The release latch will automatically lock when the battery is fully seated. Removing the Optional PC Card To remove the optional PC card, check that the computer is in boot mode and observe the following procedures. 1. Switch the computer off. 2. Slide the PC card release switch to the right. The right switch releases the bottom card and the left switch releases the top card.
4. The PC card will pop out slightly. Hold it securely and pull it out.
4-6
File No. 960-140
Installing the Optional PC Card To install the optional PC card follow the steps below. NOTE: Before installing the PC card, make sure that the computer is in boot mode. 1. Switch the computer off.
3. Insert the PC card. Carefully push it in place. 4. Check that, when the PC card is fully inserted, the PC card release lever moves to the left. The right lever releases the bottom card and the left lever releases the top card.
4-7
File No. 960-140
4.2
HDD
CAUTION: Be very careful not to press on the top or bottom of the HDD. Pressure can destroy data or damage the drive. Removing the HDD To remove the HDD follow the steps below. (See figures 4-1 to 4-3.) 1. Remove the two M2x14 silver screws securing the HDD cover and remove the cover.
Figure 4-1 Removing the HDD cover
4-8
File No. 960-140 2. Pull the HDD bracket straight with your fingernail and pull the HDD out.
NOTE: When pulling the HDD out, be sure to hold both corners of the bracket as shown below so as not to bend the bracket.
Figure 4-2 Removing the HDD 3. Remove two thin-flat-head M3 screws from the HDD bracket, and separate the bracket and the HDD.
Figure 4-3 Removing the HDD bracket Installing the HDD To install the HDD follow the steps below. (See figures 4-1 to 4-3.) 1. Secure the HDD bracket to the HDD with two flat-head M3 screws. 2. Insert the HDD into the HDD slot and push it carefully and securely into place.
4-9
File No. 960-140 3. Seat the HDD cover and fasten it with two M2x14 silver screws.
4-10
File No. 960-140
4.3
Optional Memory Module
Removing Optional Memory Module To remove the optional memory module follow the steps below. (See figures 4-4 to 4-6.) 1. Lift up the right end of the keyboard brace to remove it.
Figure 4-4 Removing the keyboard brace 2. Lift up the back edge of the keyboard.
Figure 4-5 Lifting up the keyboard
4-10
File No. 960-140 4. Lift out the keyboard and lay it against the display, being careful not to apply tension to the cables. Remove the super-thin-head M2.5 screw first, then remove the memory module.
Figure 4-6 Removing the optional memory module Installing Optional Memory Module To install the optional memory module follow the steps below. (See figures 4-4 to 4-6.) 1. Connect the memory module to the connector. CAUTION: Do not touch the connectors of the memory module or computer. Memory access trouble may arise from foreign matter adhering to the connectors. 2. Fasten the memory module with one super-thin-head M2.5 screw.
3. Seat the keyboard. The keyboard has tabs on the front, so install it by inserting from the front, taking care not to pinch the flexible cable. 4. Secure the keyboard brace. 5. Install removed components.
4-11
File No. 960-140
4.4
Keyboard
Removing the Keyboard To remove the keyboard follow the steps below. (See figure 4-7.) 1. Remove two M2x3 silver screws securing the keyboard straps and slide each strap out from under its brace. 2. Disconnect the flexible cable from PJ302 and remove the keyboard.
Figure 4-7 Removing the keyboard Installing the Keyboard To install the keyboard follow the steps below. (See figure 4-7.) 1. Slide the keyboard straps under slots in the metal plate and secure them with two M2x3 silver screws. 2. Connect the flexible cable to PJ302. 3. Seat the keyboard. The keyboard has tabs on the front, so install it by inserting the front first, taking care not to pinch the flexible cable. 4. Secure the keyboard brace. 5. Install removed components.
4-12
File No. 960-140
4.5
Display Assembly
Removing the Display Assembly To remove the display assembly follow the steps below. (See figures 4-8 to 4 -11.) 1. Lift out the metal cover. CAUTION: The metal cover is thin, so be careful not to cut yourself on the edge.
Figure 4-8 Removing the metal cover 2. Disconnect the display flexible cable from PJ250 on the system board. 3. Remove insulator covering the RTC battery cable and lift the battery cable out of its groove.
4-13
File No. 960-140
Figure 4-9 Removing the display flexible cable 4. Close the display, turn the computer upside down, and remove five M2x14 silver screws.
Figure 4-10 Removing five screws 5. Turn the computer right side up and open the display. 6. Disconnect the microphone cable from PJ470 on the system board and lift off the display assembly.
4-14
File No. 960-140
CAUTION: Make sure the flexible cable has been removed from PJ470 on the system board before removing the display assembly. An attempt to forcibly remove the display assembly when the flexible cable is still connected to PJ470 could damage the cable.
Figure 4-11 Removing the display assembly
4-15
File No. 960-140
Installing the Display Assembly To install the display assembly follow the steps below. (See figures 4-8 to 4 -11.) 1. Seat the display assembly and connect the microphone cable to PJ470 on the system board. 2. Connect the display flexible cable to PJ250 on the system board (figure 4-9). 3. Lay the metal cover in place, making sure the cover is properly aligned with the edges of the computer. 4. Route the RTC battery cable in its groove and secure it with insulator. 5. Close the display, turn the computer upside down, and fasten the display withfive M2x14 silver screws. 6. Install removed components.
4-16
File No. 960-140
4.6
RTC Battery
Removing the RTC Battery To remove the RTC battery follow the steps below. (See figure 4-12.) 1. Disconnect the RTC battery cable from PJ300 on the system board. 2. Lift out the RTC battery.
Figure 4-12 RTC battery removal Installing the RTC Battery To install the RTC battery follow the steps below. (See figure 4-12.) 1. Connect the RTC battery cable to PJ300 on the system board. 2. Seat the RTC battery. 3. Install the removed components.
4-17
File No. 960-140
4.7
System Board, Heat Sink and PC Card Slot
Removing the System Board, Heat Sink and PC Card Slot To remove the system board, heat sink and PC card slot observe the following procedures. (See figures 4-13 to 4-15.) 1. Grasp the system board and lift it out.
Figure 4-13 Removing the system board 2. Remove one M2x4 screw and two M2x6 screws securing the heat sink to the system board. 3. Remove four M2x14 screws securing both the heat sink and PC card slot to the system board. 4. Lift off the heat sink.
4-18
File No. 960-140 Figure 4-14 Removing the heat sink 5. Turn the system board over and lift off the PC card slot.
Figure 4-15 Removing the PC card slot Installing System Board, Heat Sink and PC Card Slot To install the system board, heat sink and PC card slot follow the steps below. (See figures 413 to 4-15.) 1. Secure the heat sink to the system board with one M2x4 screw, and two M2x6 screws. 2. Turn over the system board and set the PC card slot in place. Turn the system board back over and secure the PC card slot with four 2x14 silver screws. 3. Align the power connector with its housing and seat the system board.
4-19
File No. 960-140
4.8
Display Mask
Removing the Display Mask To remove the display mask follow the steps below. (See figures 4-16 to 4 -17.) 1. Remove the two mask seals on the right and left in the lower part of the display mask. 2. Remove two M2.5x5 screws that were covered by the seals. 3. Remove the AccuPoint cap.
Figure 4-16 Removing the mask seals 4. Carefully insert your fingers between the mask and top of the LCD panel and release the four latches at the top of the display mask.
4-20
File No. 960-140 5. Continue along the sides (three latches on each side) and the bottom (three latches).
Figure 4-17 Removing the display mask Installing the Display Mask To install the display mask follow the steps below. (See figures 4-16 and 4 -17.) 1. Set the display mask in place and fasten the latches starting with the three at the bottom. 2. Continue along the sides (three latches on each side) and the top (four latches). 3. Mount the AccuPoint cap. 4. Secure the display mask with two M2.5x5 screws. 5. Secure the two mask seals.
4-21
File No. 960-140
4.9
FL Inverter Board
Removing the FL Inverter Board To remove the FL inverter board follow the steps below. (See figures 4-18 to 4-19.) 1. Remove one M2x5 silver screw securing the FL inverter board. 2. Slide the FL inverter board slightly to the right to clear a small latch and lift out the board, being careful not to apply tension to the cables.
Figure 4-18 Removing the FL inverter board 3. Carefully turn the FL inverter board over and disconnect the display cable from CN1 and the FL cable from CN2.
4-22
File No. 960-140
Figure 4-19 Disconnecting the display cable Installing the FL Inverter Board To install the FL inverter board follow the steps below. (See figure 4-18 to 4-19.) 1. Connect the FL cable to CN1 on the FL inverter board and the display flexible cable to CN2. 2. Place the FL inverter board in position and secure it with one M2x5 silver screw. 3. Install the removed components.
4-23
File No. 960-140
4.10 LCD Module

Caution: Hold the LCD module in one of two ways:
1. Grasp the LCD module lightly as shown in the top left illustration. Do not grip it tightly.
2. Hold it gently between your thumb and fingers. Hold only on the side that does not have connectors along the edge.
4-24
File No. 960-140 When handling the LCD module, do not touch or apply pressure to the surface of the LCD panel. Do not touch or apply pressure to the connectors.
LCD panel
Connectors
4-25
File No. 960-140 Removing the LCD Module To remove the LCD module follow the steps below. (See figure 4-20.) 1. Remove four M2x5 silver screws securing the LCD module to the top cover. 2. Carefully rotate the LCD module out of the top cover from left to right being careful not to apply tension to the cables connected to the right side. 3. Disconnect the display flexible cable from CN1 on the LCD module.
Figure 4-20 LCD module removal
4-26
File No. 960-140
Installing the LCD Module To install the LCD module follow the steps below. (See figure 4-20.) 1. 2. 3. Connect the display flexible cable to CN1 on the LCD module. Carefully rotate the LCD module into the top cover from right to left. Secure the LCD module to the top cover with four M2x5 silver screws.
4-27
File No. 960-140
4.11 Speaker, Power Switch Board and AccuPoint Board

Removing the Speaker, Power Switch Board and AccuPoint Board To remove the speaker, power switch board and AccuPoint board follow the steps below. (See figures 4-21 and 4-23.) 1. Disconnect the speaker cable from the speaker connector and lift out the speaker with its rubber case.
Figure 4-21 Removing the speaker 2. Separate the speaker from its case. 3. Disconnect the AccuPoint flexible cable from PJ12 on the power switch board.
4-28
File No. 960-140 4. Turn over the power switch board, being careful not to apply tension to the remaining cable connection and disconnect the LCD flexible cable from PJ3 on the power switch board.
Figure 4-22 Removing the power switch board 5. Remove one M2x3 silver screw securing the AccuPoint board and lift out the board.
Figure 4-23 Removing the AccuPoint board
4-29
File No. 960-140
Installing the Speaker, Power Switch Board and AccuPoint Board To install the speaker, power switch board and AccuPoint board follow the steps below. (See figures 4-21 to 4-23.) 1. Seat the AccuPoint board and secure it with one M2x3 silver screw. 2. Connect the LCD flexible cable to PJ3 on the power switch board. 3. Connect the AccuPoint flexible cable to PJ12 on the power switch board. 4. Seat the speaker in its case. 5. Connect the speaker cable to the speaker connector and seat the speaker with its rubber case. 6. Install the removed components.
4-30
File No. 960-140
4.12 LCD Flexible Cable and Microphone

Removing LCD Flexible Cable and Microphone To remove the LCD flexible cable and microphone follow the steps below. (See figures 4 -24 to 4-29.) 1. Remove one M2x5 sliver screw securing the LCD flexible cable and two M2.5x5 screws securing the display hinges. 2. Remove two strips of tape securing the LCD flexible cable. 3. Separate the LCD module from the top cover.
Figure 4-24 Removing the LCD module
4-31
File No. 960-140 4. Remove insulator covering the microphone cable.
Figure 4 -25 Removing tape 5. Remove one M2x4 screw securing the left top cover brace to the top cover and remove a plastic support for the left top cover brace.
Figure 4-26 Removing one screw and plastic support
4-32
File No. 960-140 6. Remove the left top cover brace and microphone.
Figure 4-27 Removing the left top cover brace and microphone 7. Separate the microphone from its rubber case. 8. Remove one M2x5 silver screw and a brace for the LCD flexible cable.
Figure 4-28 Removing the LCD flexible cable
4-33
File No. 960-140 9. Remove the LCD cable by pulling it through the opening that was covered by the brace.
Figure 4-29 Removing the LCD cable
4-34
File No. 960-140
Installing LCD Flexible Cable and Microphone To install the LCD flexible cable and microphone follow the steps below. (See figures 4 -24 to 4-29.) 1. Thread the LCD cable through the slot in the top cover. 2. Seat the LCD flexible brace and secure it with one M2x5 screw. 3. Put the microphone in the rubber case and seat the microphone with rubber case in the top cover. 4. Seat the left top cover brace and plastic support, then secure the brace with one M2x4 screw. 5. Cover the microphone cable with insulator. 6. Seat the LCD module in the top cover. 7. Secure the LCD flexible cable with two strips of tape. 8. Secure the display hinges with two M2.5x5 screws and secure the LCD flexible cable with one M2x5 silver screw. 9. Install the removed components.
4-35
File No. 960-140
4.13 I/O Adapter Board
Removing the I/O Adapter Board To remove the I/O adapter board follow the steps below. (See figures 4-30 to 4-32.) 1. Remove the I/O adapter from the computer. Disconnect all the external cables from the I/O adapter. 2. Turn the I/O adapter upside down, and remove three M2x5 silver screws from the back and six M2x5 silver screws from the bottom.
Figure 4-30 Removing nine screws 3. Release one latch securing the left side, two latches securing the front edge and one latch securing the right side and then remove the upper cover.
Figure 4-31 Removing the upper cover 4. Remove four M2x4 screws securing the I/O adapter board and lift out the board.
4-36
File No. 960-140
Figure 4-32 Removing the I/O adapter board
4-37
File No. 960-140
Installing the I/O Adapter Board To install the I/O adapter board follow the steps below. (See figures 4-30 to 4 -32.) 1. Seat the I/O adapter board and secure it with four M2x4 screws. 2. Seat the top cover on the bottom cover. 3. Turn the I/O adapter upside down, and secure six M2x5 silver screws to the bottom and three M2x5 silver screws to the back.
4-38
File No. 960-140
Appendices
File No. 960-140
App-ii
File No. 960-140
Appendix
Contents
Appendix A Handling the LCD Module...................................................................... A-1 Appendix B Board Layout ........................................................................................... B-1 B.1 B.2 System Board Front View ......................................................................... B-1 System Board Back View .......................................................................... B-2
Appendix C Pin Assignments .......................................................................................C-1 C.1 C.2 C.3 C.4 C.5 C.6 C.7 C.8 C.9 C.10 C.11 C.12 PJ1 Expansion Memory Connector (140-pin)........................................ C-1
PJ200 Docking Interface Connector (140-pin)........................................... C-3 PJ250 FL Inverter I/F Connector (60-pin)................................................. C-6 PJ300 RTC Battery Connector (3-pin) ...................................................... C-7 PJ301 HDD Connector (44-pin)................................................................C-7 PJ302 Keyboard Connector (24-pin) ......................................................... C-8 PJ303 PC Card Slot Connector (150-pin).................................................. C-9 PJ401 Headphone Connector (5-pin)....................................................... C-11 PJ470 Internal Microphone Connector (2-pin)........................................ C-11 PJ471 External Microphone Connector (5-pin)........................................ C-12 PJ500 AC Adapter Connector (2-pin)...................................................... C-12 PJ510 Main Battery Connector (10-pin) .................................................. C-12
Appendix D Keyboard Scan/Character Codes ............................................................D-1 Appendix E Key Layout............................................................................................... E-1 E.1 E.2 E.3 E.4 E.5 E.6 United States (US) Keyboard..................................................................... E-1 United Kingdom (UK) Keyboard................................................................ E-1 German (GR) Keyboard ............................................................................. E-2 French (FR) Keyboard................................................................................ E-2 Spanish (SP) Keyboard............................................................................... E-3 Italian (IT) Keyboard.................................................................................. E-3
App-iii
File No. 960-140 E.7 E.8 Scandinavian (SC) Keyboard...................................................................... E-4 Swiss-German (SL) Keyboard.................................................................... E-4
Appendix F Wiring Diagrams...................................................................................... F-1 F.1 F.2 F.3 F.4 Parallel Port Wraparound Connector...........................................................F-1 Serial Port Wraparound Connector..............................................................F-1 Serial Port Direct Cable (9-Pin to 9-Pin)......................................................F-2 Serial Port Direct Cable (9-Pin to 25-Pin)....................................................F-2
Appendix G BIOS Rewrite Procedures........................................................................G-1 Appendix H Reliability .................................................................................................H-1
App-iv
File No. 960-140
Figures Figure B-1 Figure B-2 Figure E-1 Figure E-2 Figure E-3 Figure E-4 Figure E-5 Figure E-6 Figure E-7 Figure E-8 Figure F-1 Figure F-2 Figure F-3 Figure F-4 Board layout (front) ................................................................................... B-1 Board layout (back).................................................................................... B-2 US keyboard .............................................................................................. E-1 UK keyboard.............................................................................................. E-1 GR keyboard.............................................................................................. E-2 FR keyboard............................................................................................... E-2 SP keyboard............................................................................................... E-3 IT keyboard ............................................................................................... E-3 SC keyboard .............................................................................................. E-4 SL keyboard............................................................................................... E-4 Parallel port wraparound connector.............................................................F-1 Serial port wraparound connector................................................................F-1 Serial port direct cable (9-pin to 9-pin)........................................................F-2 Serial port direct cable (9-pin to 25-pin)......................................................F-2
Tables Table B-1 Table B-2 Table C-1 Table C-2 Table C-3 Table C-4 Table C-5 Table C-6 Table C-7 Table C-8 Table C-9 Table C-10 System board ICs and connectors (front).................................................... B-3 System board ICs and connectors (back) .................................................... B-3 Expansion Memory connector pin assignments (140-pin)...........................C-1 Docking Interface connector pin assignments (140-pin)..............................C-3 FL Inverter I/F connector pin assignments (60-pin)..................................... C-6 RTC Battery connector pin assignments (3-pin).......................................... C-7 HDD connector pin assignments (44-pin)................................................... C-7 Keyboard connector pin assignments (24-pin)............................................. C-8 PC card slot connector pin assignments (150-pin)....................................... C-9 Headphone connector pin assignments (5-pin).......................................... C-11 Internal Microphone connector pin assignments (2-pin)........................... C-11 External Microphone connector pin assignments (5-pin)........................... C-12
App-v
File No. 960-140 Table C-11 Table C-12 Table D-1 Table D-2 Table D-3 Table D-4 Table D-5 Table D-6 Table D-7 Table H-1 AC adapter connector pin assignments 23-pin)......................................... C-12 Main Battery connector pin assignments (10-pin) ..................................... C-12 Scan codes (set 1 and set 2)........................................................................D-1 Scan codes with left Shift key.....................................................................D-5 Scan codes in Numlock mode.....................................................................D-6 Scan codes with Fn key..............................................................................D-6 Scan codes in overlay mode........................................................................D-7 Scan codes with Ctrl key............................................................................D-7 Scan codes with Alt key .............................................................................D-8 MTBF........................................................................................................H-1
App-vi
File No. 960-140

Appendix A
Appendix A Handling the LCD Module

Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Therefore, please observe the following precautions when handling it:
1. When installing the LCD module in its cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained.
2. Be careful to align the holes at the four corners of the LCD module with the corresponding holes in its cover before securing the module with screws. Do not force the module into place, because stress can affect its performance. Note: The panels polarized surface is easily scarred, so handle it carefully.
A-1
File No. 960-140 3. If the panels surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, use a CRT cleaning agent. Apply the agent to a cloth and then wipe the panels surface. Do not apply cleanser directly to the panel.
4. If water or other liquid is left on the panels surface for a long period, it can change the screens tint or stain it. Be sure to quickly wipe off any liquid.
A-2
File No. 960-140 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks.
6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module.
A-3
File No. 960-140 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods.
8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.
9. Do not disassemble the LCD module. Disassembly can cause malfunctions.
A-4
File No. 960-140 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panels polarization.
A-5
File No. 960-140
A-6
File No. 960-140

Appendix B
Appendix B Board Layout

B.1 System Board Front View
C B
D G
Figure B-1 Board layout (front)
B-1
File No. 960-140
B.2
System Board Back View

Q
I L N T
F B
P R
J D K
M G A
Figure B-2 Board layout (back)
B-2
File No. 960-140

Table B-1 System board ICs and connectors (front)
Mark
(A) (B) (C) (D) (E) (F) (G)
Number
IC3 to 6 IC300 PJ200 PJ301 PJ303 PJ500 PJ510 System RAM BIOS ROM
Name
Docking interface connector HDD connector PC card connector DC-IN connector Main battery connector
Table B-2 System board ICs and connectors (back)

Mark
(A) (B) (C) (D) (E) (F) (G) (H) (I) (J) (K) (L) (M) (N) (O) (P) (Q) (R) (S) (T)
Number
F256 F500 F510 IC1 IC2 IC7 IC250 IC302 IC401 IC545 IC550 PJ1 PJ250 PJ300 PJ302 PJ401 PJ470 PJ471 S651 S653
Name
FL inverter and LCD fuse DC-IN fuse Battery fuse CPU System controller GA (Cello-SSP) I/O & PC card controller GA (Petunia3) Video controller KBC Sound controller Power supply microprocessor Embedded controller Expansion memory connector FLIMC* board connector RTC battery connector Keyboard connector Headphone connector Internal microphone connector External microphone connector Reset switch Panel close switch
B-3
File No. 960-140
B-4
File No. 960-140

Appendix C
Appendix C Pin Assignments

System Board C.1 PJ1 Expansion Memory Connector (140-pin)
Table C-1 Expansion Memory connector pin assignments (140-pin)(1/3)
Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 Signal name GND MD00;100 MD01;100 MD02;100 MD03;100 B3V MD04;100 MD05;100 MD06;100 MD07;100 GND CAS0;001 CAS1;001 B3V MA00B;101 MA01B;101 MA02;111 GND MD08;100 MD09;100 MD10;100 MD11;100 B3V MD12;100 MD13;100 MD14;100 I/O I/O I/O I/O I/O O I/O I/O I/O I/O O O O O O O I/O I/O I/O I/O I/O I/O I/O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 Signal Name GND MD32;100 MD33;100 MD34;100 MD35;100 B3V MD36;100 MD37;100 MD38;100 MD39;100 GND CAS4;011 CAS5;011 B3V MA03;111 MA04;111 MA05;111 GND MD40;100 MD41;100 MD42;100 MD43;100 B3V MD44;100 MD45;100 MD46;100 I/O I/O I/O I/O I/O I I/O I/O I/O I/O O O O O O I/O I/O I/O I I/O I/O I/O
C-1
File No. 960-140 Table C-1 Expansion Memory connector pin assignments (140-pin)(2/3)
Pin No. 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101 103 105 107 109 111 113 115 Signal name MD15;100 GND NC NC NC B3V NC WEC;001 RAS2;001 RAS3;001 NC GND NC NC B3V MD16;100 MD17;100 MD18;100 MD19;100 GND MD20;100 MD21;100 MD22;100 MD23;100 B3V MA06;111 MA08;111 GND MA09;111 MA10;111 B3V CAS2;011 I/O I/O O O O I/O I/O I/O I/O I/O I/O I/O I/O O O O O O Pin No. 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102 104 106 108 110 112 114 116 Signal Name MD47;100 GND NC NC NC B3V WED;001 NC NC NC NC GND NC NC B3V MD48;100 MD49;100 MD50;100 MD51;100 GND MD52;100 MD53;100 MD54;100 MD55;100 B3V MA07;111 MA11;111 GND MA00C;101 MA01C;101 B3V CAS6;011 I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O O O O O O
C-2
File No.960-140 Table C-1 Expansion Memory connector pin assignments (140-pin)(3/3)
Pin No. 117 119 121 123 125 127 129 131 133 135 137 139 Signal name CAS3;011 GND MD20;100 MD25;100 MD26;100 MD27;100 B3V MD28;100 MD29;100 MD30;100 MD31;100 GND I/O O I/O I/O I/O I/O I/O I/O I/O I/O Pin No. 118 120 122 124 126 128 130 132 134 136 138 140 Signal Name CAS7;011 GND MD56;100 MD57;100 MD58;100 MD59;100 B3V MD60;100 MD61;100 MD62;100 MD63;100 GND I/O O I/O I/O I/O I/O I/O I/O I/O I/O -
C.2
PJ200 Docking Interface Connector (140-pin)

Table C-2 Docking Interface connector pin assignments (140-pin)(1/3)
Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 Signal Name GND DAD00;100 DAD02;100 DAD04;100 DAD06;100 DAD08;100 DAD10;100 DAD12;100 DAD14;100 DAD16;100 DAD18;100 DAD20;100 DAD22;100 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 Signal Name GND DAD01;100 DAD03;100 DAD05;100 DAD07;100 DAD09;100 DAD11;100 DAD13;100 DAD15;100 DAD17;100 DAD19;100 DAD21;100 DAD23;100 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
C-3
File No. 960-140 Table C-2 Docking Interface connector pin assignments (140-pin)(2/3)
Pin No. 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 Signal Name DAD24;100 DAD26;100 DAD28;100 DAD30;100 ECGPI1;100 GND DDEVSL;000 DSPOT;000 DINT4;000 DCDSPK;110 DEJREQ;100 QSWON;100 DOCPWN;100 S5V IFVCC IFVCC VCC PRDCIN PRDCIN PRDCIN NC GND GND GND DPGNTG;000 DCBE1;000 DCBE3;000 DIRDY;000 DPCLK4;100 DIRQD;000 CK32K;100 +3.3V I/O I/O I/O I/O I/O I I/O I/O I I I/O O O O I/O I/O I/O O I/O O Pin No. 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 Signal Name DAD25;100 DAD27;100 DAD29;100 DAD31;100 DPGNTH;000 DCKRUN;000 DTRDY;000 DINT3;000 DAUDIO;100 DCDSMI;000 ECGPO0;100 DPREQH;000 DCPCLR;000 IFVCC IFVCC VCC NC PRDCIN PRDCIN PRDCIN DOCDET;000 GND GND DPREQG;000 DCBE0;000 DCBE2;000 DFRAM;000 DPAR;100 DIRQCK;100 +3.3V RCLR;100 PCONF;100 I/O I/O I/O I/O I/O O O I/O I I I O I O I/O I I/O I/O I/O I/O O O I/O
C-4
File No.960-140 Table C-2 Docking Interface connector pin assignments (140-pin)(3/3)
Pin No. 91 93 95 97 99 101 103 105 107 109 111 113 115 117 119 121 123 125 127 129 131 133 135 137 139 Signal Name USBVC1 USBDP1;100 MOUSDT;120 EXKBCK;101 GND CRTEN;000 MONID1;000 CGREEN;100 PNLST;100 DCD1;010 RXD1;110 RI1;010 TXD1;100 E232C;100 GND BUSY;100 SELCT;100 STROB;000 SLIN;000 PD0;100 PD2;100 PD4;100 PD6;100 SCL;100 B5V I/O I/O I/O I/O O O O I I I I O O I I O O I/O I/O I/O I/O I/O Pin No. 92 94 96 98 100 102 104 106 108 110 112 114 116 118 120 122 124 126 128 130 132 134 136 138 140 Signal Name USBVC1 USBDN1;000 MOUSCK;120 EXKBDT;101 CVSYNC;100 CHSYNC;100 CRED;100 CBLUE;100 MONID3;000 DSR1;010 CTS1;010 RTS1;000 DTR1;000 RIOUT;000 ACK;000 PE;100 ERROR;000 AUTFD;000 PINT;000 PD1;100 PD3;100 PD5;100 PD7;100 SDA;100 GND I/O I/O I/O I/O O O O O O I I O O I I I I O O I/O I/O I/O I/O I/O -
C-5
File No. 960-140
C.3
PJ250 FL Inverter I/F Connector (60-pin)

Table C-3 FL Inverter I/F connector pin assignments (60-pin)
Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 Signal name PWRSW;000 CHGDRG;000 PVLED VCC ISARST;000 IPSDAT;100 VCC ENDATA;120 PNLD04;120 PNLD02;120 PNLD00;120 PNLD10;120 PNLD08;120 PNLD06;120 PNLD16;120 HDDLED;000 PWLEDG;100 FL0;100 VCC GND GND GND GND GND GND GND SPKRTN;100 SHFCLK;120 FP;120 PNLD13;120 I/O I O I O O O O O O O O O O O O O O O O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 Signal Name CHGGRN;000 DCGRN;000 DCORG;000 VCC IPSCLK;000 VCC VCC PNLD05;120 PNLD03;120 PNLD01;120 PNLD11;120 PNLD09;120 PNLD07;120 PNLD17;120 PNLD15;120 PWLEDO;100 FL1;100 VCC VCC GND GND GND GND GND GND SPKOUT;100 PNLST;100 LP;120 PNLD12;120 PNLD14;120 I/O O O O O O O O O O O O O O O O I O O O
C-6
File No.960-140
C.4
PJ300 RTC Battery Connector (3-pin)

Table C-4 RTC Battery connector pin assignments (3-pin)
Pin No. 1 3 Signal name RTCVDD;100 GND I/O Pin No. 2 Signal Name NC I/O -
C.5
PJ301 HDD Connector (44-pin)

Table C-5 HDD connector pin assignments (44-pin)
Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 Signal name HDDRST;000 SD7;100 SD6;100 SD5;100 SD4;100 SD3;100 SD2;100 SD1;100 SD0;100 GND NC FIOW;010 FIOR;010 IOCRDY;100 NC IRQ14;100 SA1;100 SA0;100 HDCS0;000 HDDLED;000 VCC GND I/O O I/O I/O I/O I/O I/O I/O I/O I/O O O I I O O O I Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 Signal Name GND SA8;100 SA9;100 SA10;100 SA11;100 SA12;100 SA13;100 SA14;100 SA15;100 NC GND GND GND NC GND IOCS16;000 NC SA2;100 HDCS1;000 GND VCC NC I/O I/O I/O I/O I/O I/O I/O I/O I/O O I I -
C-7
File No. 960-140
C.6
PJ302 Keyboard Connector (24-pin)

Table C-6 Keyboard connector pin assignments (24-pin)
Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 Signal name KBRT6;100 KBRT4;100 KBRT1;100 KBRT0;100 NC KBOT06;000 KBOT02;000 KBOT07;000 KBOT03;000 KBOT01;000 KBOT11;000 GND I/O I I I I O O O O O O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 Signal Name KBRT5;100 KBRT3;100 KBRT2;100 KBRT7;100 KBOT05;000 KBOT09;000 KBOT08;000 KBOT10;000 KBOT04;000 KBOT00;000 JMODEL;000 NC I/O I I I I O O O O O O I -
C-8
File No.960-140
C.7
PJ303 PC Card Slot Connector (150-pin)

Table C-7 PC card slot connector pin assignments (150-pin) (1/3)
Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 Signal name GND ACCD1;000 ACAD02;100 ACAD04;100 GND ACAD05;100 ACAD07;100 ACCBE0;000 GND ACAVS1;100 ACAD13;100 ACAD15;100 GND ACCBE1;000 ACPAR;100 ACPERR;000 GND ACDEVS;000 MCVCCA MCVP1A ACTRDY;000 GND ACCBE2;000 ACAD18;100 ACAD20;100 GND ACRST;000 ACSERR;000 ACREQ;000 GND I/O I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I I Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 ACCLK;100 ACIRDY;000 ACFRAM;000 ACAD17;100 ACAD19;100 ACVS2;100 ACAD21;100 ACAD22;100 ACAD23;100 ACAD24;100 ACCBE3;000 O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O Signal Name GND ACAD00;000 ACAD01;100 ACAD03;100 ACAD06;100 ACD14;100 ACAD08;100 ACAD10;100 ACAD09;100 ACAD11;100 ACAD12;100 ACAD14;100 ACAD16;100 ACA18;100 ACLOCK;000 ACSTOP;000 ACGNT;000 ACINT;000 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O O I
C-9
File No. 960-140
Table C-7 PC card slot connector pin assignments (150-pin) (2/3)

Pin No. 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101 103 105 107 109 111 113 115 117 119 BCCLK;100 BCIRDY;000 BCFRAM;000 I I/O I/O Signal name ACAD25;100 ACAD26;100 ACAD27;100 GND ACAD30;100 ACAD31;100 ACCD2;000 GND GND BCAD00;100 BCAD01;100 BCAD03;100 BCAD06;100 BCD14;100 BCAD08;100 BCAD10;100 BCAD09;100 BCAD11;100 BCAD12;100 BCAD14;100 BCAD16;100 BCA18;100 BCLOCK;000 BCSTOP;000 BCGNT;000 BCINT;000 I/O I/O I/O I/O I/O I/O I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I O Pin No. 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102 104 106 108 110 112 114 116 118 120 Signal Name ACAUDI;100 ACSTSC;100 ACAD28;100 ACAD29;100 ACD02;100 ACCLKR;000 GND GND BCCD1;000 BCAD02;100 BCAD04;100 GND BCAD05;100 BCAD07;100 BCCBE0;000 GND BCVS1;100 BCAD13;100 BCAD15;100 GND BCCBE1;000 BCPAR;100 BCPERR;000 GND BCDEVS;000 MCVCCB MCVP1B BCTRDY;000 GND BCCBE2;000 I/O I/O I/O I I I/O I/O I/O I/O I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
C-10
File No.960-140 Table C-7 PC card slot connector pin assignments (150-pin) (3/3)
Pin No. 121 123 125 127 129 131 133 135 137 139 141 143 145 147 149 Signal name BCAD17;100 BCAD19;100 BCVS2;100 BCAD21;100 BCAD22;100 BCAD23;100 BCAD24;100 BCCBE3;000 BCAUDI;100 BCSTSC;100 BCAD28;100 BCAD29;100 BCD02;100 BCCLKR;000 GND I/O I/O I/O I/O I/O I/O I/O I/O I/O I I I/O I/O I/O I/O Pin No. 122 124 126 128 130 132 134 136 138 140 142 144 146 148 150 Signal Name BCAD18;100 BCAD20;100 GND BCRST;000 BCSERR;000 BCREQ;000 GND BCAD25;100 BCAD26;100 BCAD27;100 GND BCAD30;100 BCAD31;100 BCCD2;000 GND I/O I/O I/O I O O I/O I/O I/O I/O I/O O -
C.8
PJ401 Headphone Connector (5-pin)

Table C-8 Headphone connector pin assignments (5-pin)
Pin No. 1 3 11 Signal name GND ROUT SPKR I/O O I Pin No. 2 10 Signal Name LOUT SPKL I/O O I
C.9
PJ470 Internal Microphone Connector (2-pin)

Table C-9 Internal Microphone connector pin assignments (2-pin)
Pin No. 1 Signal name MIC I/O I Pin No. 2 Signal Name GND I/O -
C-11
File No. 960-140
C.10 PJ471 External Microphone Connector (5-pin)

Table C-10 External Microphone connector pin assignments (5-pin)
Pin No. 1 3 11 Signal name GND NC NC I/O Pin No. 2 10 Signal Name MIC MIC I/O I O
C.11 PJ500 AC Adapter Connector (2-pin)

Table C-11 AC adapter connector pin assignments 23-pin)
Pin No. 1 Signal name DCIN I/O Pin No. 2 Signal Name GND I/O -
C.12 PJ510 Main Battery Connector (10-pin)

Table C-12 Main Battery connector pin assignments (10-pin)
Pin No. 1 3 5 7 9 Signal name (+) DCHG SCL;100 GND GND I/O I I/O Pin No. 2 4 6 8 10 Signal Name BTMP1 S5V SDA;100 BAT1OV;000 (-) I/O I I/O I -
C-12
File No. 960-140

Appendix D
Appendix D Keyboard Scan/Character Codes

Table D-1 Scan codes (set 1 and set 2) (1/4)
Cap No. 01 02 03 04 05 06 07 08 09 10 11 12 13 Keytop ~ 1 ! 2 @ 3 # 4 $ 5 % 6 ^ 7 & 8 * 9 ( 0 ) - _ = + Code set 1 Make 29 02 03 04 05 06 07 08 09 0A 0B 0C 0D Break A9 82 83 84 85 86 87 88 89 8A 8B 8C 8D Code set 2 Make 0E 16 1E 26 25 2E 36 3D 3E 46 45 4E 55 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 Break 0E 16 1E 26 25 2E 36 3D 3E 46 45 4E 55 *2 *2 *2 Note
15 16 17 18 19 20 21 22 23 24 25 26 27 28
BkSp Tab Q W E R T Y U I O P [ { ] }
0E 0F 10 11 12 13 14 15 16 17 13 19 1A 1B
8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B
66 0D 15 1D 24 2D 2C 35 3C 43 44 4D 54 5B
F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0
66 0D 15 1D 24 2D 2C 35 3C 43 44 4D 54 5B *2 *2 *2 *2
D-1
File No. 960-140 Table D-1 Scan codes (set 1 and set 2) (2/4)
Cap No. 29 (42) 30 31 32 33 34 35 36 37 38 39 40 41 Keytop \ | Caps Lock A S D F G H J K L ; : Code set 1 Make 2B 3A 1E 1F 20 21 22 23 24 25 26 27 28 Break AB BA 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 Code set 2 Make 5D 58 1C 1B 23 2B 34 33 3B 42 4B 4C 52 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 Break 5D 58 1C 1B 23 2B 34 33 3B 42 4B 4C 52 *2 *2 *2 *2 *5 Note
43 44 45 46 47 48 49 50 51 52 53 54 55
Enter Shift (L) No.102 key Z X C V B N M , < . > / ?
1C 2A 56 2C 2D 2E 2F 30 31 32 33 34 35
9C AA D6 AC AD AE AF B0 B1 B2 B3 B4 B5
5A 12 61 1A 22 21 2A 32 31 3A 41 49 4A
F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0
5A 12 61 1A 22 21 2A 32 31 3A 41 49 4A *2 *2 *2 *2
57
Shift (R)
36
B6
59
F0
59
D-2
File No. 960-140

Cap No. 58 Keytop Ctrl Code set 1 Make 1D Break 9D 14 Code set 2 Make F0 Break 14 *3 Note
60 61 62
Alt (L) Space ALT (R) E0
38 39 38 E0
B8 B9 B8 E0
11 29 11
F0 F0 E0 F0
11 29 11
*3
75 76
Ins Del
E0 E0
52 53
E0 E0
D2 D3
E0 E0
70 71
E0 E0
F0 F0
70 71
*1 *1
79 80 81
Home End
E0 E0 E0
4B 47 4F
E0 E0 E0
CB C7 CF
E0 E0 E0
6B 6C 69
E0 E0 E0
F0 F0 F0
6B 6C 69
*1 *1 *1
83 84 85 86 89
PgUp PgDn
E0 E0 E0 E0 E0
48 50 49 51 4D
E0 E0 E0 E0 E0
C8 D0 C9 D1 CD
E0 E0 E0 E0 E0
75 72 7D 7A 74
E0 E0 E0 E0 E0
F0 F0 F0 F0 F0
75 72 7D 7A 74
*1 *1 *1 *1 *1
110 112 113 114 115 116 117 118 119 120 121
Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
01 3B 3C 3D 3E 3F 40 41 42 43 44
81 3B BC BD BE BF C0 C1 C2 C3 C4
76 05 06 04 0C 03 0B 83 0A 01 09
F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0
76 05 06 04 0C 03 0B 83 0A 01 09
D-3
File No. 960-140

Cap No. 122 123 124 Keytop F11 F12 PrintSc 57 58 *6 Code set 1 Make Break D7 D8 *6 78 07 *6 Code set 2 Make F0 F0 *6 Break 78 07 *3 *3 *6 Note
126
Pause
*7
*7
*7
*7
*7
202 203 204
Fn Win App
E0 E0 5B 5D
E0 E0 DB DD
E0 E0 1F 2F
E0 E0 F0 F0 1F 2F
*4
Notes: 1. 2. 3. 4. 5. 6. 7. * * * * * * * Scan codes differ by mode. Scan codes differ by overlay function. Combined with the Fn key, different codes are generated. The Fn key does not generate a code by itself. This key corresponds to key No. 42 in a 102-key model. Refer to Table D-6, Scan codes with Ctrl key. Refer to Table D-7, Scan codes with Alt key.
D-4
File No. 960-140

Table D-2 Scan codes with left Shift key
Cap No 75 76 79 80 81 83 84 85 86 89 203 204 Key top INS DEL Home End PgUp PgDn Win App E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 Make AA AA AA AA AA AA AA AA AA AA AA AA E0 52 E0 53 E0 4B E0 47 E0 4F E0 48 E0 50 E0 49 E0 51 E0 4D E0 5B E0 5D E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 D2 D3 CB C7 CF C8 D0 C9 D1 CD DB DD Code set 1 Break E0 2A E0 E0 2A E0 E0 2A E0 E0 2A E0 E0 2A E0 E0 2A E0 E0 2A E0 E0 2A E0 E0 2A E0 E0 2A E0 E0 2A E0 E0 2A E0 Make F0 12 F0 12 F0 12 F0 12 F0 12 F0 12 F0 12 F0 12 F0 12 F0 12 F0 12 F0 12 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 70 71 6B 6C 69 75 72 7D 7A 74 1F 2F E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 Code set 2 Break F0 70 F0 71 F0 6B F0 6C F0 69 F0 75 F0 72 F0 7D F0 7A F0 74 F0 1F F0 2F E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 12 12 12 12 12 12 12 12 12 12 12 12
NOTE: The table above shows scan codes with the left Shift key. In combination with the right Shift key, scan codes are changed as listed below: Set 1 Set 2 With left Shift With right Shift E0 AA ___________E0 B6 E0 2A____________E0 36 E0 F0 12 _________E0 F0 59 E0 12 ____________E0 59
D-5
File No. 960-140
Table D-3 Scan codes in Numlock mode

Cap No 75 76 79 80 81 83 84 85 86 89 203 204 Key top INS DEL Home End PgUp PgDn Win App E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A Make E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 52 53 4B 47 4F 48 50 49 51 4D 5B 5D E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 02 D3 CB C7 CF C8 D0 C9 D1 Code set 1 Break E0 AA E0 AA E0 AA E0 AA E0 AA E0 AA E0 AA E0 AA E0 AA E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 Make 12 12 12 12 12 12 12 12 12 12 12 12 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 70 71 6B 6C 69 75 72 7D 7A 74 1F 2F E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 70 71 Code set 2 Break E0 F0 E0 F0 12 12 12 12 12 12 12 12 12 12 12 12
6B E0 F0 6C E0 F0 69 75 72 E0 F0 E0 F0 E0 F0
7D E0 F0 7A E0 F0 74 1F 2F E0 F0 E0 F0 E0 F0
CD E0 AA DB E0 AA
DD E0 AA
Table D-4 Scan codes with Fn key

Cap No 43 58 60 121 122 Keytop ENT CTRL LALT ARROW NUMERIC E0 E0 E0 05 05 Code set 1 Make 1C 1D 38 E0 E0 E0 Break 9C 9D B8 C5 C5 E0 E0 E0 77 7E Make 5A 14 11 E0 E0 E0 F0 F0 Code set 2 Break F0 F0 F0 77 7E 5A 14 11
D-6
File No. 960-140
Table D-5 Scan codes in overlay mode

Cap No. 08 09 10 11 23 24 25 26 37 38 39 40 52 53 54 55 / 7 8 9 0 U I O P J K L ; M , Keytop (7) (8) (9) () (4) (5) (6) () (1) (2) (3) (+) (0) (,) (.) (/) E0 Code set 1 Make Break 47 48 49 37 4B 4C 4D 4A 4F 50 51 4E 52 33 53 35 E0 C7 C8 C9 B7 CB CC CD CA CF D0 D1 CE D2 B3 D3 B5 40 Make 6C 75 7D 7C 6B 73 74 7B 69 72 7A 79 70 41 71 4A Code set 2 Break F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 E0 F0 6C 75 7D 7C 6B 73 74 7B 69 72 7A 79 70 41 71 4A
Table D-6 Scan codes with Ctrl key

Key top Prt Sc Common Ctrl* Shift* Alt* E0 2A E0 E0 Shift Make E0 37 37 54 37 Code set 1 Break E0 B7 E0 AA E0 B7 E0 B7 D4 Make E0 12 E0 7C E0 F0 Code set 2 Break 7C E0 7C 7C F0 12
E0 7C E0 7C 84
E0 F0 E0 F0 F0 B4
D-7
File No. 960-140

Table D-7 Scan codes with Alt key
Key top Pause
Shift
Code set 1 Make
Code set 2 Break C5 E1 E0 14 77 E1 F0 7E 14 F0 77
Common Ctrl*
E1 1D E0 46
45 E0
E1 SD C6
7E E0 F0
*: This key generates only make codes.
D-8
File No. 960-140

Appendix E
Appendix E
E.1
Key Layout
United States (US) Keyboard
Figure E-1 US keyboard
E.2
United Kingdom (UK) Keyboard
Figure E-2 UK keyboard
E-1
File No. 960-140
E.3
German (GR) Keyboard
Figure E-3 GR keyboard
E.4
French (FR) Keyboard
Figure E-4 FR keyboard
E-2
File No. 960-140
E.5
Spanish (SP) Keyboard
Figure E-5 SP keyboard
E.6
Italian (IT) Keyboard
Figure E-6 IT keyboard
E-3
File No. 960-140
E.7
Scandinavian (SC) Keyboard
Figure E-7 SC keyboard
E.8
Swiss-German (SL) Keyboard
Figure E-8 SL keyboard
E-4
File No. 960-140

Appendix F
Appendix F
F.1
Wiring Diagrams
Parallel Port Wraparound Connector
Figure F-1 Parallel port wraparound connector
F.2
Serial Port Wraparound Connector
Figure F-2 Serial port wraparound connector
F-1
File No. 960-140
F.3
Serial Port Direct Cable (9-Pin to 9-Pin)
Figure F-3 Serial port direct cable (9-pin to 9-pin)
F.4
Serial Port Direct Cable (9-Pin to 25-Pin)
Figure F-4 Serial port direct cable (9-pin to 25-pin)
F-2
File No. 960-140

Appendix G
Appendix G BIOS Rewrite Procedures

This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool: Diagnostics disk for the computer Rewriting the BIOS 1. Set the system to boot mode. 2. Turn off the power to the computer. 3. Remove the external cable and any optional memory or PC card. 4. Turn on the power while holding down the F12 key. (Keep holding down the key until the system speaker sounds a beep.) 5. When the BIOS message displays, insert the diagnostics disk into the FDD, then press Enter to start the BIOS rewrite program. 6. When the process is completed, eject the diagnostics disk and press the reset switch to restart the system.
G-1
File No. 960-140
G-2
File No. 960-140

Appendix H
Appendix H Reliability
The following table shows MTBF (Mean Time Between Failures) for each component. Table H-1 MTBF
Component LCD Keyboard HDD FDD Pointing Device AC adapter Time (hours) 50,000 37,000 300,000 30,000 37,000 50,000
H-1
File No. 960-140
H-2

Toshiba Personal Computer Libretto 100CT

Uploaded by

Copyright:

Available Formats

Toshiba Personal Computer Libretto 100CT

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Toshiba Personal Computer Libretto 100CT

Uploaded by

Copyright:

Available Formats

File No.

File No. 960-140

File No. 960-140

File No. 960-140

File No. 960-140

Chapter 3 3.1 3.2 3.3 3.4 3.5 3.6

File No. 960-140 4.13 I/O Adapter Board................................................................................................4-35

File No. 960-140

Chapter 1 Hardware Overview

File No. 960-140

File No. 960-140

File No. 960-140

File No. 960-140

Figure 1-1 Front of the computer

Figure 1-2 System unit configuration

File No. 960-140

System Unit Block Diagram

Figure 1-3 is a block diagram of the system unit.

Figure 1-3 System unit block diagram

File No. 960-140

3.5-inch External FDD

Figure 1-4 3.5-inch FDD Table 1-1 3.5-inch FDD specifications

Modified Frequency Modulation (MFM)

File No. 960-140

2.5-inch Hard Disk Drive

Figure 1-5 2.5-inch HDD Table 1-2 2.5-inch HDD specifications

File No. 960-140

Figure 1-6 Keyboard

File No. 960-140

TFT Color LCD

Figure 1-7 TFT color LCD Table 1-3 LCD specifications

Display area Contrast

File No. 960-140

*NOTE: The FL currents at power on are: Level 3 : 3.5mA Level 2 : 2.9mA

File No. 960-140

IFVCC MCV S5V RTCV

5.0 5.0 5.0 5.0

NO YES YES YES

NO YES YES YES

File No. 960-140

1.8.1 Main Battery

File No. 960-140

File No. 960-140

File No. 960-140

Chapter 2 Troubleshooting Procedures

File No. 960-140

File No. 960-140

System Board Troubleshooting.............................................................................2-14 Procedure 1 Procedure 2 Procedure 3 Procedure 4 Procedure 5

FDD Troubleshooting...........................................................................................2-25 Procedure 1 Procedure 2 Procedure 3

HDD Troubleshooting ..........................................................................................2-28 Procedure 1 Procedure 2 Procedure 3 Procedure 4 Procedure 5

Keyboard Troubleshooting....................................................................................2-34 Procedure 1 Procedure 2

File No. 960-140

File No. 960-140

File No. 960-140

Figure 2-1 Troubleshooting flowchart (1/2)

File No. 960-140

File No. 960-140

Power Supply Troubleshooting

File No. 960-140 Table 2-2 DC IN icon

File No. 960-140