Toshiba Qosmio f40 f45

Toshiba Personal Computer Qosmio F40/F45
(PQF43x) (PQF44x) (PQF46x) (PQF47x)
Maintenance Manual
TOSHIBA CORPORATION
S/ No
Qosmio F40/F45 Maintenance Manual
Copyright 2007 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba Qosmio F40/F45 Maintenance Manual First edition May 2007 Disclaimer The information presented in this manual has been reviewed and validated for accuracy. The included set of instructions and descriptions are accurate for the Qosmio F40/F45 at the time of this manual's production. However, succeeding computers and manuals are subject to change without notice. Therefore, Toshiba assumes no liability for damages incurred directly or indirectly from errors, omissions, or discrepancies between any succeeding product and this manual. Trademarks Intel and Pentium are registered trademarks of Intel Corporation. IBM, IBM PC/XT, PC/AT, PS/2 and OS/2 are registered trademarks of IBM Corporation. Windows XP home edition are registered trademarks of Microsoft Corporation. Sound Blaster and Pro are trademarks of Creative Technology Ltd. UNIX is a registered trademark of X/Open Company Ltd. NetWare are registered trademarks of Novell, Inc. All other properties are trademarks or registered trademarks of their respective holders.
ii
Preface
This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Qosmio F40/F45, referred to as Qosmio F40/F45 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field. SAFETY PRECAUTIONS Four types of messages are used in this manual to bring important information to your attention. Each of these messages will be italicized and identified as shown below. DANGER: Danger indicates the existence of a hazard that could result in death or serious bodily injury, if the safety instruction is not observed.
WARNING: Warning indicates the existence of a hazard that could result in bodily injury, if the safety instruction is not observed.
CAUTION: Caution indicates the existence of a hazard that could result in property damage, if the safety instruction is not observed.
NOTE: Note contains general information that relates to your safe maintenance service. Improper repair of the computer may result in safety hazards. Toshiba requires service technicians and authorized dealers or service providers to ensure the following safety precautions are adhered to strictly. Be sure to fasten screws securely with the right screwdriver. If a screw is not fully fastened, it could come loose, creating a danger of a short circuit, which could cause overheating, smoke or fire. If you replace the battery pack, RTC battery or backup battery, be sure to use only the same model battery or an equivalent battery recommended by Toshiba. Installation of the wrong battery can cause the battery to explode.
iii
The manual is divided into the following parts: Chapter 1 Chapter 2 Chapter 3 Chapter 4 Appendices Hardware Overview describes the Qosmio F40/F45 system unit and each FRU. Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Replacement Procedures describes the removal and replacement of the FRUs. The appendices describe the following: Handling the LCD Module Board Layout Pin Assignments Keyboard scan/character codes Key Layout BIOS Rewrite Procedures EC/KBC Rewrite Procedures
iv
Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations. The key top symbol as it appears on the keyboard is printed in boldface type. Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause (Break) means you must hold down Ctrl and at the same time press Pause (Break). If three keys are used, hold down the first two and at the same time press the third. User input Text that you are instructed to type in is shown in the boldface type below: DISKCOPY A: B: The display Text generated by the XXXXX that appears on its display is presented in the type face below:
Format complete System transferred
Chapter 1 Hardware Overview
1 Hardware Overview
1.1 Features
1.1 Features
1 Hardware Overview
Chapter 1
1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8
Contents
Features ......................................................................................................................... 5 System Unit Components ........................................................................................... 14 2.5-inch HDD.............................................................................................................. 22 DVD Super Multi (+-R Double Layer)....................................................................... 23 HD DVD-ROM........................................................................................................... 25 HD DVD-R ................................................................................................................. 26 Power Supply .............................................................................................................. 27 Batteries ...................................................................................................................... 28 1.1.1 1.1.2 1.1.3 Main Battery.......................................................................................... 28 Battery Charging Control ...................................................................... 28 RTC Battery .......................................................................................... 29
1 Hardware Overview
1.1 Features
Figures Figure 1-1A Figure 1-1B Figure 1-2 Figure 1-3 Figure 1-4 Figure 1-5 Figure 1-6 ID Parts Description Placement Part A ........................................................... 10 ID Parts Description Placement Part B ........................................................... 11 Computer Block Diagram ............................................................................... 12 System Board Configurations ......................................................................... 13 System Unit Block Diagram ........................................................................... 15 SATA HDD..................................................................................................... 22 DVD Super Multi Drive.................................................................................. 23
Tables Table 1-1 Table 1-2 Table 1-3 Table 1-4 Table 1-5 Table 1-6 HDD Specifications......................................................................................... 22 DVD Super Multi Drive Specifications .......................................................... 23 HD DVD-ROM Drive Specifications ............................................................. 25 HD DVD-R Drive Specifications.................................................................... 26 Battery Specifications ..................................................................................... 28 Quick/Normal Charging Time ........................................................................ 29
1.1 Features
1 Hardware Overview
1.1
Features
The Toshiba Qosmio F40/F45 a full size notebook PC based on the Core2 Duo Processor and Celeron M Processor, providing high-speed processing capabilities and advanced features. The computer employs a Lithium Ion battery that allows it to be battery-operated for a longer period of time. The display uses 15.4-inch WXGA LCD panel, at a resolution of 1280 by 800 pixels. The uPGA socket supports BTO/CTO for the CPU so that the system can be designed to suit your needs.
The computer has the following features: Processor The CPU is the Core2 Duo Processor and Celeron M Processor. Core2 Duo Processor (800MHz) T7100(1.80G)/T7300(2.00G)/ T7500(2.20G)/T7700(2.40G) Hz Celeron M Processor (533MHz) 540(1.86G)/550(2.00G) Hz Host Bridge System Controller System Controller: Intel Crestline PM965/GM965/GL960 + ICH8M. Graphics Intel GM965/GL960 integrated graphic or PM965 with nVIDIA NB8P-GS/NB8MGS. Memory The computer has two SO-DIMMs slot comes standard with DDRII-667MHz module. It supports PC2-5300 and uses SO-DIMMs (DDRII SDRAM) driven at 1.8 V, accepting BTO/CTO for your memory requirements. It can incorporate up to 4 GB of main memory. Using the following sizes of memory modules: y 512 MB (32M168P)/667 MHZ
1 Hardware Overview y 1024 MB (64M816P)/667 MHZ y 2048 MB (64Mx16x16P)/667 MHZ Hard Disk Drive (HDD)
1.1 Features
The computer accommodates 9.5 mm and 12.5 mm two kinds of height HDD types with following storage capacities: y 60 GB (9.5 mm thick) SATA (5,400rpm) y 80 GB (9.5 mm thick) SATA (5,400rpm) y 100 GB (9.5 mm thick) SATA (5,400rpm) y 120 GB (9.5 mm thick) SATA (5,400rpm) y 160 GB (9.5 mm thick) SATA (5,400rpm) y 160 GB (12.5 mm thick ) SATA (4,200rpm) y 200 GB (9.5 mm thick) SATA (4,200rpm) y 250 GB (12.5 mm thick) SATA (4,200rpm) y 300 GB (12.5 mm thick) SATA (4,200rpm) ODD The computer accommodates a fixed 12.7 mm height ODD with one of following types: y DVD Super Multi +-R Double Layer drive y DVD Super Multi +-R Double Layer with Label Flash Support drive (BTO) y HD DVD-ROM with Super Multi drive y HD DVD-R with Super Multi drive Display The LCD displays available come with one of following two types: y 15.4 WXGA CSV 1-Lamp 200nits color display, resolution 1280800 y 15.4 WXGA CSV 2-Lamps 500nits color display, resolution 1280800 Keyboard The keyboard supports 30 kinds of country keyboards.
1.1 Features
1 Hardware Overview
Battery The computer has a removable 6 Cell Lithium Ion battery pack and an internal RTC battery (rechargeable). Universal Serial Bus (USB) Ports The computer has four USB 2.0 ports. It is supported to daisy-chain a maximum of 127 USB devices. The serial data transfer rate is 480 Mbps or 12 Mbps and 1.5 Mbps. These ports support PnP installation and hot plugging. External Monitor Port A 15-pin external monitor port is provided, through which the computer automatically recognizes an external VESA DDC 2B compatible monitor. S Video Out Port The S Video out port lets you transfer video data to external devices. HDMI Out Port (BTO) A HDMI monitor can be connected to the HDMI out port on the computer. Video-In Jack The Video-In Jack lets you transfer NTSC or PAL data to the computer. TV Antenna Port The TV Antenna Port lets you connect a TV Antenna. PC Card Slot (BTO) A PC Card slot is provided to hold PC Card Standard Type II (5.0 mm) card, capable of using a variety of PC Cards including 16-bit Multiple Function PC Cards and 32bit Card Bus Cards. PC card HDD boot does not be supported.
1 Hardware Overview Express Card Slot (BTO)
1.1 Features
The ICH8M provides PCI Express root ports which are compliant to the PCI Express Base Specification, Revision 1.0a. The root port supports 2.5 Gb/s bandwidth in each direction (5 Gb/s concurrent) and two virtual channels for full isochronous data support.
Multiple Digital Media Card Slot This computer is equipped with Multiple Digital Media Card Slot that can accommodate SD/ Mini-SD/ Micro-SD/ SD-IO/ SDHC/ MS/ MS Pro/ MMC/ XD memory cards. This slot is for your memory card requirements to provide memory card read on your computer.
Toshiba Pointing Device Toshiba Pointing Device has one kind of Synaptic Touchpad. Sound System The Realtek ALC888 integrated audio controller supports multimedia. The sound system contains the following: y Stereo speakers y Headphone jack y Internal microphone y External microphone jack
Line-In Jack The Line-In Jack lets you transfer analogue sound to the computer. LAN (BTO) The internal LAN board supports 10/100Mbit, enabling connection to a LAN at up to 100Mbps. It also supports Wake-up on LAN from S3/S4/S5 and PXE boot support. The LAN board has RJ45 jack to directly accommodate a LAN cable. Wireless LAN
1.1 Features
1 Hardware Overview
The internal Mini Card slot supports IEEE802.11g (MOW) / IEEE802.11ag (MOW) / IEEE802.11ag (ROW) / IEEE802.11ag (JPN) / IEEE802.11agn (MOW) / IEEE802.11agn (ROW) / IEEE802.11agn (JPN) card. The Antenna has three wires dual band antenna support for BTO. Internal Modem (BTO) The computer contains a MDC, enabling data and fax communication. It supports ITU- T V.90 (for rest countries)/V.92 (America, Canada, UK, Germany & France). The transfer rates are 56 Kbps for data reception, 33.6 Kbps for data transmission and 14,400 bps for fax transmission. Note, however, that the actual speed depends on the line quality. The RJ11 modem jack is used to accommodate a telephone line. IEEE 1394 The IEEE 1394 serial data transfer rate is 400 Mbps, this port supports hot plugging. Finger Print (BTO) This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password to the fingerprint authentication device, it is no longer necessary to input the password from the keyboard. Just by swiping the finger against the fingerprint sensor.
Internal Camera (BTO) The computer has an internal camera. The camera has 1.3Mpix resolution support.
ROBSON Card (BTO) Robson is Intels platform non-volatile memory (NVM) disk-cache accelerator which delivers a fast cold boot as well resumes from hibernation while saving power. It also accelerates application loading and run time through intelligent file caching. The computer has 512 MB or 1 GB sizes of Robson card modules.
1 Hardware Overview
1.1 Features
Figures 1-1A/1-1B/1-2/1-3 and 1-4 show the computer and its system unit configuration, respectively.
Figure 1-1A
ID Parts Description Placement Part A
10
1.1 Features
1 Hardware Overview
Figure 1-2B
ID Parts Description Placement Part B
11
1 Hardware Overview
1.1 Features
Figure 1-3 Computer Block Diagram
12
1.1 Features
1 Hardware Overview
Figure 1-4 System Board Configurations
13
1 Hardware Overview
1.2 System Unit Components
1.2
System Unit Components

Figure 1-4 is Block Diagram of the System Unit
14
1 Hardware Overview
Figure 1-5 System Unit Block Diagram
15
1 Hardware Overview
The system unit of the computer consists of the following components: Processor: Core2 Duo Processor and Celeron M Processor. y Core2 Duo Processor (800MHz) Core speed: 1.80/2.00/2.20/2.40 GHz System bus: 800 MHz On-die level 2 cache: 2 MB (1.8 GHz) On-die level 2 cache: 4 MB (2.0/2.2/2.4 GHz)
y Celeron M Processor (533MHz) Core speed: 1.86/2.00 GHz System bus: 533 MHz On-die level 2 cache: 1 MB Memory Two expansion memory slots are provided. They can hold 512/1024/2048MB expansion memory modules available as options to grow up to 4.0 GB. y PC2-5300/667MHz DDRII SDRAM supported y 512/1024/2048MB modules supported 512 MB (32M x 16 x 8P) 1024 MB (64M x 8 x 16P) 2048 MB (64M x 16 x 16P) y 1.8 volt operation y No parity bit y 64-bit data transfer BIOS ROM (Flash EEPROM) y 8Mb x 1 chip (1024KB flash parts) 64.00Kb used for EC BIOS 8.00Kb used for ESCD 15.13Kb used for Memory Initial Code 12.71Kb used for ACPI 30.03Kb used for CPU update module 64.03Kb used for Intel VGA BIOS 55.28Kb used for Finger Printer ROM 51.44Kb used for string data 39.13Kb used for nVidia G84
16
1.2 System Unit Components System Controllers y North Bridge: Intel Crestline PM965/GM965/GL960
1 Hardware Overview
39.03Kb used for nVidia G86 24.01Kb used for PXE ROM 35.65Kb used for SMI 37.86Kb used for PNP Code 11.55Kb used for BIOS Code 21.04Kb used for USB 16.17Kb used for Setup 9.31Kb used for AHCI 3.82Kb used for Display Engine 1.09Kb used for Decode Code 0.52Kb used for Compress Code 6.15Kb used for Pre-Shadow Code 29.23Kb used for ROM Executable 64.00Kb used for Bootblock 866.04Kb used for Used Size 157.96Kb used for Free Size
CPU Interface and Control System Memory Support PCI Express* Graphics (PEG) Interface Integrated Display Interface Support Internal Graphics Features (GM965/GL960) Direct Media Interface (DMI) Power Management Security and Manageability Serial ATA Interface ICH8 Audio Control
y South Bridge: Intel ICH8-M Direct Media Interface (DMI) PCI Express* Interface Serial ATA (SATA) Controller Advanced Host Controller Interface (AHCI) Intel Matrix Storage Technology PCI Interface IDE Interface Low Pin Count (LPC) Interface Serial Peripheral Interface (SPI) Compatibility Modules Advanced Programmable Interrupt Controller (APIC) Universal Serial Bus (USB) Controller
17
1 Hardware Overview
LAN Controller RTC GPIO Enhanced Power Management Manageability System Management Bus (SMBus 2.0) Intel High Definition Audio Controller Integrated FAN Speed Control
Graphics Controller Intel GM965/GL960 integrated graphics or PM965 with nVIDIA NB8P-GS / NB8M-GS, nVIDIA graphics controller contains the following features: y Unified Shader Architecture. y Microsoft DirectX 10 Shader Model 4 Support. y High efficiency integrated adaptable and programmable Video Processor. y Integrated Bit Stream Processor. y Best quality 10-bit display pipeline. y Integrated HDMI 1.2a Support. y Improved Internal Temperature Sensor. y Improved Integrated Spread Spectrum Support. PC Card Controller y TI 8402/8412 CardBus/PC Card Controller 16-bit PCMCIA and 32-bit CardBus SD/SDHC/MS/MS Pro/MMC/XD Card Controller Audio Controller Realtek ALC888 integrated audio controller supports multimedia. The sound system contains the following features: y Ten DAC channels support 16/20/24-bit PCM format for 7.1 sound playback, plus 2 channels of independent stereo sound output through the front panel output. y 2 stereo ADCs support 16/20/24-bit PCM format. y All DACs support 44.1 k/48 k/96 k/192 kHz sample rate. y All ADCs support 44.1 k/48 k/96 k sample rate.
18
1 Hardware Overview
y Two independent 16/20/24-bit S/PDIF-Out converters support 44.1 k/48 k/96 k/192 kHz sample rate. y One 16/20/24-bit S/PDIF-In converter supports 44.1 k/48 k/96 k/192 kHz sample rate. y High quality analog differential CD input. y Support external PCBEEP input and built-in digital BEEP generator. y Two jack detection pins each designed to detect up to 4 jacks. y All analog jacks are stereo input and output re-tasking for analog plug & play. y Built-in headphone amplifiers for each re-tasking jack. y Two digital GPIOs and one analog GPIO for customized applications. KBC/EC (Keyboard Controller/Embedded Controller) A single KBC W8769 chip is used to serve as KBC/ EC and Super IO. y KBC Scan controller function Interface controller function y EC Battery EEPROM y 24C02 equivalent (128 words x 16 bits, I2C interface) integrated in battery pack. Storing records of battery use Clock Generator y SLG8SP510 Generating the clock signal required for the system Power supply sequence control Overheat shutdown support LED control Beep control Device ON/OFF Cooling fan speed control Universal I/O port Battery capacity check Flash memory reprogramming function EC access interface I2C communication control
19
1 Hardware Overview
Modem Controller Built-in MDC card with Askey. Functions of modem controller: y Digital signal conductor protection y Ring wake-up support y Azalia interface y Communication codes supported: For data communication: V.90 (China)/V.92, data rates: 28kbps/56kbps V.34 extended rates: 33.6K/2400/V.32 turbo, V.32 bits and fallbacks For fax: V.17, V.27, V.29, V.34 and V.21 Channel 2, V.253 Class 1 fax LAN Controller y Realtek RTL8101E 10/100Mbit IEEE 802.3 10BASE-T/100BASE-TX compliant physical layer interface IEEE 802.3u Auto-Negotiation support Digital Adaptive Equalization control 10BASE-T auto-polarity correction LAN Connect interface Automatic detection of unplugged mode Remote boot (PXE 2.1) Smart power down when link is not detected Wireless LAN Controller y Support following 3 kinds of mini PCI wireless LAN cards IEEE 802.11g IEEE 802.11ag IEEE 802.11agn y Data Rate IEEE 802.11g: Standard 54M bps IEEE 802.11ag: Standard 54M bps IEEE 802.11agn: Standard 130M bps y Frequency Channel IEEE802.11a: 2.4GHz IEEE802.11ag: 2.4GHz / 5.4GHz
20
1.2 System Unit Components IEEE802.11agn: 2.4GHz / 5.4GHz
1 Hardware Overview
21
1 Hardware Overview
1.3 2.5-inch HDD
1.3
2.5-inch HDD
The computer contains an extremely low-profile and lightweight, high-performance HDD. The HDD incorporates 9.5 mm / 12.5 mm height magnetic disk and mini-Winchester type magnetic heads. The HDD interface conforms to Serial ATA. Storage capacities supported are 60, 80, 100, 120, 160, 200, 250, 300 GB. The HDD is shown in Figure 1-5 and some of its specifications are listed in Table 1-1.
Figure 1-6 SATA HDD Table 1-1 HDD Specifications

Item Capacity (GB) Rotational Speed (RPM) Height User Data Sectors Bytes / Sector Item Capacity (GB) Rotational Speed (RPM) Height User Data Sectors Bytes / Sector 160 GB 4200 rpm 12.5 mm 5400 rpm 9.5 mm 200 GB 4200 rpm 9.5 mm 390,721,968 512 60 GB 5400 rpm 9.5 mm 117,210,240 512 80 GB 5400 rpm 9.5 mm 156,301,488 512 Specifications 250 GB 4200 rpm 12.5 mm 488,397,168 512 300 GB 4200 rpm 12.5 mm 586,072,368 512 Specifications 100 GB 5400 rpm 9.5 mm 195,371,568 512 120 GB 5400 rpm 9.5 mm 234,442,648 512
312,581,808 512
22
1.4
DVD Super Multi (+-R Double Layer)) 1 Hardware Overview
1.4
DVD Super Multi (+-R Double Layer)
The DVD Super Multi drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed, CD-RW at 4x speed, US CD-RW at 24x speed, High Speed CDRW at 10x speed, DVD-R at 8x speed, DVD-RW at 6x speed, DVD+R at 8x speed, DVD+R (Double Layer) at 4x speed, DVD-R (Double Layer) at 4x speed, DVD+RW at 8x speed and DVD-RAM at 5x speed. The DVD Super Multi drive is shown in Figure 1-6 and its specifications are listed in Table 1-2.
Figure 1-7 DVD Super Multi Drive Table 1-2 DVD Super Multi Drive Specifications
Item Data Transfer Rate (Mbytes/s) Access Time (ms) Average Random Access Data Buffer Size (Mbytes) 2MB DVD: DVD-VIDEO, DVD-ROM, DVD-R, DVD-RW, DVD-RAM, DVD+R, DVD+-R (Double Layer), DVD+RW. CD: CD-DA, CD-ROM, CD-R, CD-RW, CD-ROMXA, Photo CD (MultiSession), Video CD, CD-Extra (CD+), CD-Text. 130 130 DVD-ROM Mode 33.3 (U-DMA transfer mode 2) 16.6 (PIO mode 4, Multiword DMA mode 2) CD-ROM Mode
Formats Supported
23
1 Hardware Overview
1.5 HD DVD-ROM
24
1.4
DVD Super Multi (+-R Double Layer)) 1 Hardware Overview
1.5
HD DVD-ROM
The HD DVD-ROM drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum, the drive can play back a DVD at 8x speed, read HD DVD ROM at 1x speed, CDROM at 24x speed, and write CD-R at 16x speed, CD-RW at 4x speed, US CD-RW at 10x speed, High Speed CD-RW at 10x speed, DVD-R at 4x speed, DVD-RW at 4x speed, DVD+R at 4x speed, DVD+R (Double Layer) at 2.4x speed, DVD-R (Double Layer) at 2x speed, DVD+RW at 4x speed and DVD-RAM at 3x speed. The specifications of the HD DVD-ROM drive are listed in Table 1-3.
Table 1-3 HD DVD-ROM Drive Specifications

Item Data Transfer Rate (Mbytes/s) Access Time (ms) Average Random Access Data Buffer Size (Mbytes) 8,126KB DVD: DVD-VIDEO, DVD-ROM, DVD-R, DVD-RW, DVD-RAM, DVD+-R, DVD+-R (Double Layer), DVD+RW, HD DVD-ROM Formats Supported CD: CD-DA, CD-ROM, CD-R, CD-RW, CD-ROM XA, Photo CD (MultiSession), HS CD-RW,US CD-RW, Video CD, CD-Extra (CD+), CD-Text, CD-MIDI, CD-I, CD-I Bridge. 330 160 HD DVD-ROM Mode 33.3 (U-DMA transfer mode 2) 16.7 (PIO mode 4, Multiword DMA mode 2) DVD-ROM Mode
25
1 Hardware Overview
1.6 HD DVD-R
1.6
HD DVD-R
The HD DVD-R drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum, the drive can play back a DVD at 8x speed, read HD DVD ROM at 1x speed, HD DVD-R at 1x speed ,CD-ROM at 24x speed, and write CD-R at 16x speed, CD-RW at 4x speed, US CD-RW at 10x speed, High Speed CD-RW at 10x speed, HD DVD-R at 1x speed, DVD-R at 4x speed, DVD-RW at 4x speed, DVD+R at 4x speed, DVD+R (Double Layer) at 2.4x speed, DVD-R (Double Layer) at 2x speed, DVD+RW at 4x speed and DVD-RAM at 3x speed. The specifications of the HD DVD-R drive are listed in Table 1-4.
Table 1-4 HD DVD-R Drive Specifications

Item Data Transfer Rate (Mbytes/s) Access Time (ms) Average Random Access Data Buffer Size (Mbytes) 8,126KB DVD: DVD-VIDEO, DVD-ROM, DVD-R, DVD-RW, DVD-RAM, DVD+-R, DVD+-R (Double Layer), DVD+RW, HD DVD-ROM, HD DVD-R, HD DVD-R (Double Layer). CD: CD-DA, CD-ROM, CD-R, CD-RW, CD-ROM XA, Photo CD (MultiSession), HS CD-RW,US CD-RW, Video CD, CD-Extra (CD+), CD-Text, CD-MIDI, CD-I, CD-I Bridge. 330 180 HD DVD-ROM Mode 33.3 (U-DMA transfer mode 2) 16.7 (PIO mode 4, Multiword DMA mode 2) DVD-ROM Mode
Formats Supported
26
1.8 Batteries
1 Hardware Overview
1.7
Power Supply
The power supply unit provides many different voltages for the system board and performs the following functions: 1. Power input monitor y Checks whether the DC power supply (AC adapter) is connected to the computer. y Checks whether the battery pack is connected to the computer. y Monitors the DC power supply input voltage (AC Adapter output voltage). 2. Power supply's internal control y Turns on and off the battery pack charging power supply. y Issues a charging current instruction to the PWM control IC of the battery pack charging power supply. y Controls the supply of DC power supply input (AC Adapter output) to the power supply unit. y Controls the supply of power to the system block (load/logic circuit side). y Controls forced shutdown if the power supply malfunctions. 3. Logic circuit control y Instructs the gate array to enable/disable tuning the power on. y Controls power-on/off operation. 4. Status display y Turns on the Power LED (in Blue or AMBER). y Battery indicator (in Blue or AMBER or AMBER Flash). 5. External interface y Performs communication through the I2C bus (via the internal EC/KBC). y Transfers the power supply operation mode. 6. Output monitor y Monitors the voltage output to the system block (load/logic circuit side). y Monitors the voltage, over voltage, input/output current of the battery pack. y Monitors the internal temperature of the battery pack. y Monitors the supply voltage from the AC adapter.
27
1 Hardware Overview
1.7 Power Supply
1.8
Batteries
The computer has the following two types of batteries: Main Battery Pack Real Time Clock (RTC) Battery Table 1-5 lists the specifications of these batteries. Table 1-5 Battery Specifications
Battery Type Main Battery Pack RTC Battery 6 Cell Material Lithium Ion Lithium Ion Output voltage 10.8 V 3.0 V Capacity 4000 mAh 14 mAh
1.1.1
Main Battery The main battery pack serves as the computer's main power source when the AC adapter is not attached. The main battery maintains the state of the computer so that it can resume it.
1.1.2
Battery Charging Control Battery charging is controlled by WINBOND 8769L. When the AC adapter and battery pack are attached to the computer, the 8769L controls the charge on/off state and detects a full charge.
Battery Charge When the AC adapter is attached, the battery is charged by off-state charge when the system is powered off or by on-state charge when it is powered on.
28
1.8
Batteries 1 Hardware Overview
Table 1-6 Quick/Normal Charging Time

State Off-State Charge On-State Charge 6 Cell 6 Cell Charge Time About 4 hours max About 4~10 hours max
NOTE: The time required for normal charge depends on the power consumption by the system. Using the fluorescent lamp and frequently accessing the disk consume much power and lengthen the charge time. Any of the following cases stops battery charge: 1. 2. 3. The battery becomes fully charged. The AC adapter or battery pack is removed. The battery or AC adapter voltage is abnormal.
Detection of full charge A full charge is detected only when the battery is being charged by quick or normal charge. A full charge is detected when either of the following conditions is met: 1. 2. The current in the battery charging circuit drops below the predetermined value. The charging time exceeds the fixed limit.
1.1.3
RTC Battery The RTC battery provides power to keep the current date, time and other system information in memory while the computer is turned off.
29
2 Troubleshooting
2
Chapter 2 Troubleshooting
2-i
2 Troubleshooting
Chapter 2
2.1 2.2 2.3
Contents
Outline.................................................................................................................... 2-1 Basic Flowchart...................................................................................................... 2-2 Power Supply ......................................................................................................... 2-6 Procedure 1 Power Icon Check....................................................................... 2-6 Procedure 2 Connection Check....................................................................... 2-8 Procedure 3 Replacement Check .................................................................... 2-8
2.4
System Board ......................................................................................................... 2-9 Procedure 1 Message Check ........................................................................... 2-9 Procedure 2 Test Program Check ................................................................. 2-10 Procedure 3 Replacement Check .................................................................. 2-10
2.5
HDD ..................................................................................................................... 2-11 Procedure 1 Message Check ......................................................................... 2-11 Procedure 2 Partition Check ......................................................................... 2-11 Procedure 3 Format Check............................................................................ 2-12 Procedure 4 Test Program Check ................................................................. 2-13 Procedure 5 Connector Check and Replacement Check............................... 2-14
2.6
Keyboard .............................................................................................................. 2-15 Procedure 1 Test Program Check ................................................................. 2-15 Procedure 2 Connector Check and Replacement Check............................... 2-15
2.7
Display ................................................................................................................. 2-16 Procedure 1 External Monitor Check ........................................................... 2-16 Procedure 2 Test Program Check ................................................................. 2-16 Procedure 3 Connector Check and Replacement Check............................... 2-16
2.8
ODD (Optical Disk Drive) ................................................................................... 2-18 Procedure 1 ODD Cleaning Check ............................................................... 2-18 Procedure 2 Test Program Check ................................................................. 2-18 Procedure 3 Connector Check and Replacement Check............................... 2-18
2.9
LAN...................................................................................................................... 2-20 Procedure 1 Test Program Check ................................................................. 2-20 Procedure 2 Connector Check and Replacement Check............................... 2-20
2-ii
2 Troubleshooting
2.10
SD/SD-IO/MS/MS pro/MMC/XD Card .............................................................. 2-21 Procedure 1 Test Program Check ................................................................. 2-21 Procedure 2 Connector Check ...................................................................... 2-21
2.11
Finger Print (Optional) ......................................................................................... 2-22 Procedure 1 Test Program Check ................................................................. 2-22 Procedure 2 Connector Check ...................................................................... 2-22
2.12
Audio Test ............................................................................................................ 2-23 Procedure 1 Test Program Check ................................................................. 2-23 Procedure 2 Connector Check and Replacement Check............................... 2-23
2.13
IEEE 1394 Test .................................................................................................... 2-24 Procedure 1 Test Program Check ................................................................. 2-24 Procedure 2 Connector Check ...................................................................... 2-24
2.14
Cooling Module.................................................................................................... 2-25 Procedure 1 Test Program Check ................................................................. 2-25 Procedure 2 Connector Check and Replacement Check............................... 2-25
2-iii
2 Troubleshooting
Figures Figure 2-1 Basic flowchart(1/2)....................................................................................... 2-3
Tables Table 2-1 HDD error code and status........................................................................... 2-13
2-iv
2.1 Outline
2 Troubleshooting
2.1 Outline
This chapter describes the fault diagnosis procedures for field replaceable units (FRUs) in the computer. The FRUs covered here are as follows: 1. System Board 2. 2.5-inch HDD 4. Display 5. ODD drive 7. SD/SD-IO/MS/MS pro/MMC/XD 9. Speaker 9. IEEE 1394
3. Keyboard 6. LAN 8. Finger Print 10. Cooling module
See Chapter 4 for the procedures to replace FRUs and Chapter 3 for the procedures to use test programs. The following tools are required to perform the diagnostic procedures: 1. Diagnostics (maintenance test program) disk 2. Phillips screwdrivers (2 mm, 2.5 mm) 3. Cleaning disk kit (for ODD drive cleaning) 4. Bootable CD 5. Multi-meter 6. External monitor 7. Headphone 8. Microphone 9. A-BEX TEST DVD 10. Music CD 11. DVD TSD-1 (TOSHIBA EMI DVD Test Media)
2-1
2 Troubleshooting
2.2 Basic Flowchart
2.2 Basic Flowchart

The basic flowchart in Figure 2-1 serves as a guide for identifying a possibly faulty FRU. Before going through the diagnostic flowchart steps, verify the following: Ask the user if a password has been registered and, if so, ask him or her to enter the password. If the user has forgotten the system password, use a jump wire to make a short circuit on M/B B500 location, then turn the computer power on. When booted, the computer overrides password protection and automatically erases the current password. Make sure the Windows Vista Home Premium has been installed on the HDD. Any other operating system can cause the computer to malfunction. Make sure any piece of optional equipment has been installed.
2-2
2.2 Basic Flowchart
2 Troubleshooting
Star t Connect the AC Adapter
No DC IN LED on ?? Yes No BATTERY LED on ?? Yes Turn the power on. Yes Any error message displayed ?? No Message "In Touch with Tomorrow Toshiba" displayed No
Follow the power supply diagnostic procedure in Section 2.3
Follow the power supply diagnostic procedure in Section 2.3
Follow the system board diagnostic procedure in Section 2.4
Follow the display diagnostic procedure in Section 2.7
Yes Yes "Password=" displayed ?? No OS started ?? No Yes 1 Figure 2-1 Basic Flowchart (1/2) Follow the HDD diagnostic procedure in Section 2.5 See the previous page to delete the password.
2-3
2 Troubleshooting
2.2 Basic Flowchart
1 No Keyboard works well ?? Follow the keyboard diagnostic procedure in Section 2.6
Insert Bootable CD into ODD
Diagnostic Program Loaded ?? Yes Perform each test with the diagnostic program.
No
Follow the ODD diagnostic procedure in Section 2.8
Any error detected by the diagnostic program ?? No Perform the continuous test to check if the error is intermittent.
Yes
Identify the test resulting in the error and perform the appropriate diagnostic procedures
Any error detected by the diagnostic program ?? No The system is normal. END
Yes
Identify the test resulting in the error and perform the appropriate diagnostic procedures
Figure 2-1
Basic Flowchart (2/2)
2-4
2.2 Basic Flowchart
2 Troubleshooting
If the diagnostic program cannot detect an error, the error may be intermittent. Run the continuous test program repeatedly to isolate the problem. Check the log utilities function to confirm which diagnostic test detected the error, then perform the appropriate troubleshooting procedures as follows: 1. If an error is detected by the System test, Memory test, Async test, Printer test, Sound test, or Real Timer test, follow the system board troubleshooting procedures in Section 2.4. 2. If an error is detected by the Hard Disk test, follow the HDD troubleshooting procedures in Section 2.5. 3. If an error is detected by the Keyboard test, follow the keyboard troubleshooting procedures in Section 2.6. 4. If an error is detected by the Display test, follow the display troubleshooting procedures in Section 2.7. 5. If an error is detected by the ODD test, follow the ODD troubleshooting procedures in Section 2.8. 6. If an error is detected by the LAN test, follow the LAN troubleshooting procedures in section 2.9. 7. If an error is detected by the SD Card test, follow the SD Card troubleshooting procedures in section 2.10 8. If an error is detected by the Finger Print test, follow the Finger Print troubleshooting procedures in section 2.11. 9. If an error is detected by the Speaker test, follow the Speaker troubleshooting procedures in section 2.12. 10. If an error is detected by the IEEE 1394 test, follow the IEEE 1394 troubleshooting procedures in section 2.13. 11. If an error is detected by the Fan On/Off test, follow the cooling module troubleshooting procedures in Section 2.14.
2-5
2 Troubleshooting
2.3 Power Supply
2.3 Power Supply

The power supply in the computer controls many functions and components. To check if the power supply is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Procedure 2 Procedure 3 Power Icon Check Connection Check Replacement Check
Procedure 1 Power Icon Check The following two power LEDs indicate the power supply status: Battery LED DC IN LED The power supply controller displays the power supply status through the Battery and DC IN LEDs as in the tables below. Battery LED
Battery LED On in Amber On in Blue Blinking in Amber (at equal intervals) Off Else Battery being charged Battery fully charged, with AC adapter connected Battery low *1 while driving the computer Power supply status
2-6
2.3 Power Supply DC IN LED

DC IN LED On in Blue Off Off Power supply status DC power being supplied (from the AC adapter) Battery damage and cant charge during DC-in. Else
2 Troubleshooting
If the DC IN LED off, follow the steps below: 1. Remove the battery pack and the AC adapter to shut off power supply to the computer. 2. Attach the battery and AC adapter back again. If the LED still off, follow the steps below: Check 1 Check 2 Make sure the DC IN LED goes on in Blue. If it does not, go to Procedure 2. Make sure the Battery LED goes on in Amber or Blue. If it does not, go to Procedure 3.
2-7
2 Troubleshooting
2.3 Power Supply
Procedure 2 Connection Check Power is supplied to the system board as illustrated below:
AC adaptor AC power cord AC adaptor cord Battery pack System board
Follow the steps below to check whether each connector has been connected correctly: Check 1 Make sure the AC adaptor and AC power cord have been firmly plugged into the DC IN socket and wall outlet, respectively. When they have been connected correctly, perform Check 2. Check 2 Connect a new AC adaptor and AC power cord. If the DC IN LED does not go on, go to Procedure 3. If the battery LED does not go on, perform Check 3. Check 3 Make sure the battery pack has been correctly installed in the computer. If the battery LED does not go on while the battery pack has been installed correctly, go to Procedure 3. Procedure 3 Replacement Check The system board, power supply board, or CPU may be faulty. Disassemble the computer according to Chapter 4 and follow the steps below: Check 1 Replace the power supply board with a new one. If the battery pack is still not working properly, perform Check 2. Replace the system board with a new one. If the battery pack is still not working properly, perform Check 3. Replace the CPU with a new one.
Check 2
Check 3
2-8
2.4
System Board
2 Troubleshooting
2.4 System Board

To check if the system board is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Test Program Check Procedure 3 Replacement Check Procedure 1 Message Check When the power is turned on, the system performs the self-diagnostic Power On Self Test (POST) embedded in the BIOS ROM. The POST tests and initializes each IC on the system board. If an error message appears on the display, perform Check 1. If there is no error message, go to Procedure 2. If FREE-DOS or Windows Vista Home Premium is loaded normally, go to Procedure 3. Check 1 If the following error message is displayed on the screen, press the F1 key as prompted. These errors occur when the system configuration preserved in the RTC memory (generally called CMOS memory) does not match the actual configuration or when the data is lost. If you press the F1 key as prompted by the message, the TSETUP screen appears to set the system configuration. If the error message appears frequently when the power is turned on, replace the RTC battery. If any other error message is displayed, perform Check 2.
*** Bad RTC battery *** Check system. Then press [F1] key
Check 2
If the following error message is displayed on the screen, press any key as prompted by the message. The error message appears when either data stored in RAM to be resumed is lost because the battery has been exhausted or the system board is faulty. If any other error message displays, perform Check 3. Resume failure and press any key to continue.
Check 3
2-9
2 Troubleshooting
2.4 System Board
Procedure 2 Test Program Check The maintenance test program contains several programs for diagnosing the system board and CPU. Execute the following test programs using the procedures described in Chapter 3. 1. System test 2. Memory test 3. Keyboard test 4. Display test 5. Hard Disk test 6. Mouse test 7. SD Card/Memory stick test 8. ODD test 9. Sound test 10. LAN test If an error is detected during these tests, go to Procedure 3. Procedure 3 Replacement Check The system board, memory, or CPU may be defective. Disassemble the computer following the steps described in Chapter 4 and replace the system board, memory module or CPU with a new one.
2-10
2.5 2.5-inch HDD
2 Troubleshooting
2.5 HDD
To check if the 9.5mm or 12.5mm HDD is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Partition Check Procedure 3 Format Check Procedure 4 Test Program Check Procedure 5 Connector Check and Replacement Check
CAUTION: The contents of the HDD will be erased when the HDD diagnostic test or formatting is executed. Save the required contents of the HDD to floppy disks or other storage drive in advance.
Procedure 1 Message Check When the computer's HDD does not function properly, some of the following error messages may appear on the display. Follow the steps below to check the HDD. Check 1 If either of the following messages appears, go to Procedure 2. If the following messages do not appear, perform Check 3. Insert system disk in drive Press any key when ready ..... or Non-System disk or disk error Replace and press any key Check 2 Check TSETUP to see if the Hard Disk option has been set to Not used. If so, choose another setting and restart the computer. If the problem persists, go to Procedure 2.
Procedure 2 Partition Check Boot from the DOS system. Perform the following checks: Check 1 Type C: and press the Enter key. If you cannot change to drive C, perform Check 2. If you can change to drive C, perform Check 3. Type FDISK and press the Enter key. Choose Display partition information from the FDISK menu. If drive C is listed, perform Check 3. If drive C is not listed, return to the FDISK menu and choose the option to
Check 2
2-11
2 Troubleshooting
2.5 2.5-inch HDD
create a DOS partition on drive C. Then restart the computer.. If the problem persists, go to Procedure 3. Check 3 If drive C is listed as active in the FDISK menu, perform Check 4. If drive C is not listed as active, return to the FDISK menu and choose the option to set the active partition for drive C. Then restart the computer. If the problem persists, perform Check 4. Enter DIR C: and press the Enter key. If the following message is displayed, go to Procedure 3. If contents of drive C are listed on the display, perform Check 5. Invalid media type reading drive C Abort, Retry, Fail? Check 5 Use the SYS command in the DOS system to install system files. If the following message appears on the display, the system files have been transferred to the HDD. Restart the computer. If the problem persists, go to Procedure 3. System transferred
Check 4
NOTE: If the computer is running Windows Vista Home Premium and the hard disk capacity is more than 512 MB, the FDISK program will ask if you need support for a partition larger than 2 GB. Select Y for large partition support; however, be sure to read the precaution regarding access by other operating systems.
Procedure 3 Format Check The 2.5-inch HDD is formatted using the low-level format program and the FREE-DOS FORMAT program. Using these programs, follow the steps below to format the HDD. Check 1 Enter FORMAT C:/S/U to format the HDD and transfer system files. If the following message appears on the display, the HDD has been formatted. Format complete If you cannot format the HDD using the test program, go to Procedure 4.
2-12
2.5 2.5-inch HDD
2 Troubleshooting
Procedure 4 Test Program Check Run the HDD test program stored on the maintenance test program disk for all test items. See Chapter 3 for details on how to use the test program. If an error is detected during the HDD test, an error code and status will be displayed. The error codes and their status names are listed in Table 2-1. If an error code is not generated and the problem still exists, go to Procedure 5. Table 2- 1 HDD error code and status
Code 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16
Status Get Parameter Fail ! Read Old Data Error Write Pattern Error Read Back Data Error Data Compare Error Restore Data Error Read Verify Error Seek Error Disk Controller Self Test Failed Disk Controller Test unexpected interrupt Failed Disk Controller action Test Failed Disk dos not support SMART Disk read attribute threshold error Disk read attribute value error Disk SMART attribute value error
2-13
2 Troubleshooting
2.5 2.5-inch HDD
Procedure 5 Connector Check and Replacement Check The HDD or system board may be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 Make sure the following connectors have been firmly connected to the HDD, system board and CPU.
HDD System board CPU
If any connector is loose or off, reconnect it firmly and return to Procedure 1. If there is still an error, perform Check 2. Check 2 The HDD may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4. If the problem persists, perform Check 3. The System board may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4. If the problem persists, perform Check 4. The CPU may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4.
Check 3
Check 4
2-14
2.6 Keyboard
2 Troubleshooting
2.6 Keyboard
To check if the computers keyboard is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check
Procedure 1 Test Program Check Execute the Keyboard test available as part of the maintenance test program. See Chapter 3 for information on how to perform the test. If an error is detected in the test, go to Procedure 2. If no error is detected, the keyboard itself is normal. Procedure 2 Connector Check and Replacement Check The keyboard or system board may be disconnected or faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 Make sure the keyboard cable has been firmly connected to the system board.
Keyboard System board CPU
If the cable is loose or off, reconnect it firmly and return to Procedure 1. If there is still an error, perform Check 2. Check 2 The keyboard may be faulty. Replace it with a new one following the instructions in Chapter 4. If the problem persists, perform Check 3. The System board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the keyboard is still not functioning properly, perform Check 4. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persists, perform Check 5. The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.
Check 3
Check 4
Check 5
2-15
2 Troubleshooting
2.7 Display
2.7 Display
To check if the computers display is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 External Monitor Check Procedure 2 Test Program Check Procedure 3 Connector Check and Replacement Check Procedure 1 External Monitor Check Connect an external monitor to the computer's external monitor port, then boot the computer. The computer automatically detects the external monitor even if resume mode is enabled. If the external monitor works correctly, the internal LCD, LCD/FL cable, or FL may be faulty. Go to Procedure 3. If the external monitor appears to have the same problem as the internal monitor, the system board may be faulty. Go to Procedure 2. Procedure 2 Test Program Check Insert the diagnostics bootable CD in the computer's CD ROM, turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If an error is detected in the test, go to Procedure 3. If no error is detected, the display itself is normal. Procedure 3 Connector Check and Replacement Check The display unit has an LCD module, Fluorescent lamp (FL), panel close switch and FL inverter board. Any of the components or their connections may be defective. Disassemble the computer following the steps described in Chapter 4, then perform the following checks: (1) If the FL does not light, perform Check 1. (2) If characters or graphics are not displayed normally, perform Check 5. (3) If the FL remains lit when the display is closed, the panel close switch may be defective. Perform Check 8. Check 1 Make sure the following cables have been firmly connected to the system board and FL inverter board.
FL inverter board HV cable System board LCD/FL cable CPU
FL
Check 2
If any of the cables is loose or off, reconnect it firmly and return to Procedure 3. If there is still an error, perform Check 2. The LCD/FL cable may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 3.
2-16
2.7 Display
2 Troubleshooting
Check 3 Check 4 Check 5
The FL may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 4. The FL inverter board may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 5. Make sure the LCD/FL cable has been firmly connected to the system board and LCD module.
FL inverter board
System board LCD/FL cable
CPU
Check 6 Check 7 Check 8 Check 9 Check 10
If the cable is loose or off, reconnect it firmly and return to Procedure 3. If there is still an error, perform Check 6. The LCD/FL inverter cable may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 7. The LCD module may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 8. The System board may be faulty. Replace it with a new one. If there is still an error, perform Check 9. The CPU may be faulty. Replace it with a new one following the instructions in Chapter 4. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persists, perform Check 10.
2-17
2 Troubleshooting
2.8 ODD Drive
2.8 ODD (Optical Disk Drive)

To check if the internal ODD drive is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 ODD Cleaning Check Procedure 2 Test Program Check Procedure 3 Connector Check and Replacement Check
Procedure 1 ODD Cleaning Check 1. Turn off the power to the computer. 2. Open the ODD tray by inserting a slender object such as a straightened paper clip into the eject hole. The object must be long enough to activate the eject mechanism. 3. Clean the laser pickup lens with a lens cleaner. Apply the cleaner to a cloth and wipe the lens. 4. If the ODD drive still does not function properly after cleaning, go to Procedure 2. Procedure 2 Test Program Check Execute the ODD drive test program available as part of the maintenance test program. Insert the diagnostics CD in the computer's CD, turn on the computer and run the test. Then insert a test ODD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) into the ODD drive. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 3. Procedure 3 Connector Check and Replacement Check The ODD drive is connected to the system board by the connector. The connector may be disconnected from the system board or faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 Make sure the following connector has been firmly connected to the ODD drive and the system board.
ODD drive Attachment case Connector
System board
CPU
If the connector is loose or off, reconnect it firmly and return to Procedure 2. If there is still an error, perform Check 2. Check 2 The connector may be faulty. Replace the connector with a new one following the steps in Chapter 4. If the ODD drive is still not functioning properly, perform Check 3.
2-18
2.8 ODD Drive
2 Troubleshooting
Check 3
Check 4
Check 5
Check 6
The ODD drive may be faulty. Replace the ODD drive with a new one following the steps in Chapter 4. If the ODD drive is still not functioning properly, perform Check 4. The system board may be faulty. Replace it with new one following the instructions in Chapter 4. If the ODD drive is still not functioning properly, perform Check 5. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 6. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 3.
2-19
2 Troubleshooting
2.9 LAN
2.9 LAN
To check if the computers LAN is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check
Procedure 1 Test Program Check Execute the LAN check program available as part of the maintenance test program. This program will check the LAN. Insert the Bootable CD into the CD. Turn on the computer and run the check program. See Chapter 3 for information on how to perform the check. If any abnormal is detected by the check, go to Procedure 2
Procedure 2 Connector Check and Replacement Check The LAN connector (RJ45) is mounted on the system board. If the LAN malfunctions, the system board or CPU might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 The system board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the LAN is still not functioning properly, perform Check 2. Check 2 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persists, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.
2-20
2.10 SD Card/Memory Stick
2 Troubleshooting
2.10 SD/SD-IO/MS/MS pro/MMC/XD Card

To check if the computers SD/SD-IO/MS/MS Pro/MMC/XD Card is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check
Procedure 1 Test Program Check Execute the SD/SD-IO/MS/MS Pro/MMC/XD Card test program available as part of the maintenance test program. This program checks the SD/SD-IO/MS/MS Pro/MMC/XD card. Insert the Bootable CD into the CD. Turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 2
Procedure 2 Connector Check The Memory Card connector is mounted on the system board. If the Memory Card malfunctions, the system board or CPU might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 The system board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the Memory Card is still not functioning properly, perform Check 2. Check 2 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persists, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.
2-21
2 Troubleshooting
2.11 Finger Print (Optional)
2.11 Finger Print (Optional)

To check if the computers Finger Print is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check
Procedure 1 Test Program Check Execute the Finger Print test program available as part of the maintenance test program. This program checks the Finger Print. Insert the Bootable CD into the CD. Turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 2
Procedure 2 Connector Check The Finger Print connector is mounted on the system board. If the Finger Print malfunctions, the system board or Finger Print Board might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 The Finger Print board may be faulty. Replace it with a new one following the instructions in Chapter 4. Then go through procedure 1 again. If the Finger Print is still not functioning properly, perform Check 2. Check 2 The system board may be defective. Replace the system board with a new one following the steps described in Chapter 4. Then go through procedure 1 again.
2-22
2.12 Audio Test
2 Troubleshooting
2.12 Audio Test

To check if the computers Speaker is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check
Procedure 1 Test Program Check Execute the Audio test available as part of the maintenance test program. See Chapter 3 for information on how to perform the test. If an error is detected in the test, go to Procedure 2. If no error is detected, the Audio itself is normal. Procedure 2 Connector Check and Replacement Check The Audio or system board may be disconnected or faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 Make sure the Speaker cable has been firmly connected to the system board. Speaker System board CPU
If the cable is loose or off, reconnect it firmly and return to Procedure 1. If there is still an error, perform Check 2. Check 2 The Speaker may be faulty. Replace it with a new one following the instructions in Chapter 4. If the problem persists, perform Check 3. The System board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the Audio is still not functioning properly, perform Check 4. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 5. The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.
Check 3
Check 4
Check 5
2-23
2 Troubleshooting
2.13 IEEE 1394 Test
2.13 IEEE 1394 Test

To check if the computers IEEE 1394 is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check
Procedure 1 Test Program Check Execute the IEEE 1394 test program available as part of the maintenance test program. This program checks the IEEE 1394. Insert the Bootable CD into the CD. Turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 2
Procedure 2 Connector Check The IEEE 1394 connector is mounted on the system board. If the IEEE 1394 malfunctions, the system board or CPU might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 The system board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the IEEE 1394 is still not functioning properly, perform Check 2. Check 2 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persists, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.
2-24
2.14 Cooling Module
2 Troubleshooting
2.14 Cooling Module

To check if the computers cooling module is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check
Procedure 1 Test Program Check Execute the Fan On/Off test program available as part of the maintenance test program. This test program checks the cooling module. Insert the diagnostics bootable CD in the computer's CD, turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 2.
Procedure 2 Connector Check and Replacement Check The cooling module is connected to the system board. If the cooling module malfunctions, there may be a bad connection between the cooling module and the system board or either might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 Make sure the cooling module has been firmly connected to the connector on the system board. Also make sure that the tape is not stuck to any part of the fan and that the fan is free of foreign matter.
Cooling module
System board
CPU
Check 2
Check 3
Check 4
If the connector is disconnected, connect it firmly to the system board and return to Procedure 1. If the tape is stuck to any part of the fan, stick it back to the specified point. If a foreign matter is found in the fan, remove it and then return to Procedure 1. If there is still an error, perform Check 2. The cooling module may be faulty. Replace it with a new one following the steps in Chapter 4. If the cooling module is still not functioning properly, perform Check 3. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persists, perform Check 4. The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.
2-25
Chapter 3 Diagnostic Programs
3 Diagnostic Programs
Chapter 3 Contents
3.1 3.2 General.......................................................................................................................... 1 Quick Start .................................................................................................................... 3 3.2.1 3.2.2 3.2.3 3.2.4 3.2.5 3.2.6 3.2.7 3.2.8 3.2.9 3.2.10 3.2.11 3.2.12 3.2.13 3.2.14 3.2.15 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 3.3.9 3.3.10 3.4 3.5 Quick Test ............................................................................................... 3 Customization Test.................................................................................. 3 Keyboard Layout test .............................................................................. 7 Hotkey Test ............................................................................................. 8 Audio Play Test ....................................................................................... 8 Audio Record Test................................................................................... 8 DMI Read ................................................................................................ 8 DMI Write ............................................................................................... 9 Finger Printer Detect Test ..................................................................... 10 Finger Printer Scan Test ....................................................................... 10 Finger Printer Information Clear ............................................... 11 System Information ............................................................................... 11 View Logs ............................................................................................. 12 Exit to Free DOS .................................................................................. 12 The Diagnostics Screen Explanation..................................................... 13 Overview ............................................................................................... 16 Batch Parameters Configuration ........................................................... 17 Items Parameters Configuration........................................................... 19 Load Batch Parameters.......................................................................... 20 Save Batch Parameters .......................................................................... 21 LOG Parameters Setting........................................................................ 22 Specify LOG Viewer............................................................................. 23 Display LOG File .................................................................................. 23 LOG Viewer .......................................................................................... 24 LOG File Sample................................................................................... 25
Options........................................................................................................................ 16
Subtests ....................................................................................................................... 27 System Test................................................................................................................. 30
ii
QosmioF40/F45dynabook Qosmio F40 Maintenance Manual
3 Diagnostic Programs 3.6 3.7 3.8 3.9 3.10 3.11 3.12 Memory Test............................................................................................................... 34 Storage ........................................................................................................................ 40 Video........................................................................................................................... 44 Communication (COMM) .......................................................................................... 53 Peripheral .................................................................................................................... 54 Error Codes and description........................................................................................ 58 Quick Test Item List ................................................................................................... 63
QosmioF40/F45dynabook Qosmio F40 Maintenance Manual
iii
3.1 General
3.1
General
This chapter explains the diagnostic programs which tests and diagnoses the functions of the hardware components of this computer. The diagnostic programs can be classified into two types: OPTION and DIAGNOSTIC TEST. NOTE 1: This Diagnostic supports Honolulu10/10G NOTE 2: Before running a test, be sure to: 1. Check that all the cables are connected securely. 2. Exit the application that is currently running and close Windows. The OPTION includes the following functions:

Select All Items Test All Items Edit Batch Parameters Load Batch Parameters Save Batch Parameters Log Parameters Specify Log Viewer Display Error Log File DOS Shell Exit to Free-DOS
The DIAGNOSTIC TEST Devices include the following tests:

System Test Memory Test Storage Test Video Test Communication Test Peripheral Test Keyboard Layout Test Hot Key Test Audio Play Test Audio Record Test DMI Read DMI Write Finger Printer Detect Test Finger Printer Scan Test Finger Printer Information Clear System Information
QosmioF40/F45dynabook Qosmio F40 Maintenance Manual 1
3 Diagnostic Programs Before running the diagnostic programs, get the following tools prepared:

3.1 General
A Service Diagnostic BOOT CD A Formatted FLOPPY DISK A Test Media CD (A-BEX TEST CD-ROM TCDR-702)(for CD-ROM test) A Test Media DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) An External Monitor (for DISPLAY test) A CD-ROM Driver (for CD-ROM test) Audio Line for audio record test A Data CD (for CD-ROM test)
The following chapters describe all the test details. The test items could be selected from the DIAGNOSTIC TEST menu. Note: When booting up the unit for the first time, the system will automatically select the location of the result log file. If a USB floppy drive is connected, and there is an unprotected floppy diskette with more then 50KB spare space in the drive, system will save all log files into the root directory the diskette; otherwise, system will save all log files in the root directory of RAM disk.
2 QosmioF40/F45dynabook Qosmio F40
Maintenance Manual
3.2 Quick Start
3.2
Quick Start
When the system is booting from Service Diagnostic CD, the following screen will be displayed:
Please select a test item or select 0 to exit to Free-DOS: 3.2.1 Quick Test When this item is selected, the system will run the configured test items and generate a test report automatically. When the test is completed, a file named Quick.log would be saved in the defined location. When Quick.log is being created, meanwhile, a file named quick.log has already existed, the system will automatically rename Quick.log to Quick.old for the backup purpose of the log file. For the detail of test item, please refer to Quick Test Item List. 3.2.2 Customization Test When this item is selected, the system will run the diagnostic programs according to the procedures you defined. When the test is completed, a file named Custom.log will be saved in the defined location. Please see the following example-- Mouse test.
1.
Use arrow key to select TouchPad item on Peripheral in the menu, then press Space key to select it. (When it is being selected, there is a X marked in the [ ])
3.2 Quick Start
Select Test Mouse or press F8 to run the test. The prompt information would be displayed in the screen as below. This test item needs user to verify whether the mouse works normally.
The test result will be displayed in the following screen:
Maintenance Manual
3.2 Quick Start
Here is another method to run the test: Highlight a test item by using arrow keys, then, press Enter to start. If there are parameters provided, user should set parameters in the parameter dialog window.
CPU Speed Test (Step by Step):

1. Select test item:
Select SystemCPUCPU Speed, then, press the Enter key.
2. Parameters Setting
Choose the OK button after you set the proper parameters in the following window.
3.2 Quick Start
3. Test Result
System will automatically run and display the test result as follows:
Following is the comparison report of the two testing methods mentioned above: 1) Configuration and Running As to the method used in Mouse test, the user is required to select test items by pressing Space key and set the parameters artificially, (See 3.3.3 Items Parameters Configuration) Then press F8 to start the test. User should configure each parameter in advance; otherwise the default parameters would be used. Using this method, user is allowed to select more than one test item at one time. 2) Running the current test item As to the method adopted in CPU Speed test, user should highlight the test item and press Enter to start testing. And the user has to setup the parameters every time before running the test. Using this method, only one test item would be tested at one time.
Maintenance Manual
3.2 Quick Start
3.2.3 Keyboard Layout test The test purpose is to check whether 18 kinds of European keyboards run well during the test procedure. When users choose the item, the names of these countries will be displayed on the screen for user choice. User press any index of token in ASCII, and the program will test the kind of keymap of the country.
The test screen would be shown as below:
It requires user to press the key and check whether the key in the screen changes color or not. User can terminate test by typing END. When testing the Fn key, it must press the Enter key at the same time.
3.2 Quick Start
When the user has checked all the keys and all the keys in the screen have changed color, the diagnostics program would automatically end the test and report the pass information. If keyboard test fails, program will terminate the test and report the fail information when it is time to timeout. The test will end when all keys are pressed or test time is out after 100 seconds. 3.2.4 Hotkey Test Check whether Hotkey run well. Hotkey test mainly functional keys, for example: IE Key Audio play etc. The methods of testing hotkey are different from keyboard tests sometimes depending on the specific type of notebooks, and this explains why some types of notebooks can be tested together with keyboard while others cannot. Press E+ +N+D to quit the test. 3.2.5 Audio Play Test Check whether the system could playback audio normally. When the test is completed, a file named Audio_P.log will be saved in the defined location. NOTE : If there is no surround sound system, it's normal that Surround_Out Left Channel Test/ Surround_Out Right Channel Test/Center_Out Channel Test/ Lfe_Out Channel no Sound. 3.2.6 Audio Record Test Check whether the system could record the sound normally. If there is no error during the whole test, Pass; otherwise Fail. The test will repeat for four times. When the test is completed, a file named autest.log will be saved in the defined location. 3.2.7 DMI Read Read the information from the systems SMBIOS and display it in the screen as follows:
Maintenance Manual
3.2 Quick Start
User can press any key to exit the program. 3.2.8 DMI Write In addition to reading the DMI information, DMI Write also permits attributes editing and updating: Manufacture, Product Name, Version, Serial Number, and OEM Part Number, etc. The following screen will be displayed:
In this screen, there are two lines which attribute could be edited and updated. The 1st line (the font in yellow with blue background) shows the attributes value that is read from the current system and the 2nd line (the font in red with turquoise background) shows the same value as that in the 1st line before users editing. User can modify the attributes value in the 2nd line and press Enter to confirm the current edition and continue editing the next attribute.
3.2 Quick Start
During the editing, user could press F2 to confirm the DMI attribute update or press F4 to ignore the modification. Press ESC to exit the program of DMI Write. The confirmation screen is as below:
The attributes that have been modified would be marked in red; otherwise in yellow. User could press F2 to save the changes, or press F4 to ignore and exit the current program. 3.2.9 Finger Printer Detect Test Both Finger Printer Detect and Finger Printer Scan refer to finger print test, which means finger print identification system. Finger Printer Detect, a self test of finger print test, detects the existence of the device. If it exists, the system will prompt a message of PASS, otherwise the message will be FAIL. 3.2.10 Finger Printer Scan Test In Finger Printer Scan test, the system scans a finger print for three times and displays Succeeded if successfully collected finger print information. Then it will scan the finger print one more time for comparison and display PASS if succeeded. If the comparison is not successful, the system will request another scan for totally five times and display FAIL if it always fails. Note: Because, execution of this test vanishes all fingerprint data. When you perform this test, please make it only failure of a fingerprint sensor.
10 QosmioF40/F45dynabook Qosmio F40 Maintenance Manual
3.2 Quick Start 3.2.11 Finger Printer Information Clear Select this item to clear all the information in the FP Device. 3.2.12 System Information
This function is used to read the system information. When the test is completed, a file named System.log will be saved in the defined location. During the reading process, the following screen will be displayed to indicate that the progress is in detection:
On the left column of the above screen, the detected hardware components are listed. The corresponding information of the detected hardware components is displayed on the right of the screen. It displays the current running status information of the check program. The name of the program is marked on the top of the screen. At the bottom, the function keys are listed for user operation. During the detection, keyboard operation is invalid. When the detection is finished, the hardware components information will be displayed as follows:
3.2 Quick Start
User can use function keys listed on the bottom of the screen to display the configuration of the component or exit the current program. On the left column, the components information is listed and user can use arrow keys or PgUp/PgDn to view the list and highlight the chosen component. On the right column, the configuration information of the highlighted component is listed. Press ESC to exit this program. 3.2.13 View Logs User can enter one choice to view a log file in the screen as follows.
3.2.14 Exit to Free DOS Select this item to exit to Free DOS.
3.2 Quick Start 3.2.15 The Diagnostics Screen Explanation
Below is an example of running a test item. It includes the following parts: Diagnostics Windows, Test Status Area, Progress Bar, Error List, Test Items Title, Status Bar and Message Box.
1. Diagnostics Windows When a test item is running, a Diagnostics Windows is displayed in full screen. It consists of the following parts: Title Bar, Test Running Status and Report Panel, Status Bar. There would prompt a message box called USER BREAK in the central of the window whether user press ESC to interrupt the test. 2. Test Running Status and Report Panel Test Running Status and Report Panel are located on the middle of Diagnostics Windows. Test item name, test process and test result are displayed in the left; Test status and result are displayed in the upper right corner of the screen. It displays the test status of the current test item TEST (in testing), PASS (test finished and its result is passed), FAIL (test finished and its result is failed) and SKIP (test skipped). The error list of each test module is displayed at the lower right corner of the screen. It would display the total error quantity found in the test, the most recent five error codes and description would be shown here. Detailed error report could be viewed with Logview.exe. When pressing ESC key during the test process, a User Break Windows will be popped up for the user to select.
3 Diagnostic Programs 3. USER BREAK
3.2 Quick Start
Pressing ESC key to interrupt the test, USER BREAK message box would be prompted out in the central of Diagnostics Window for the user to select the following actions: CONTINUE---- Continue the test; SKIP---- Stop the sub-item of current test item to go to the next items test; ABORT----Stop the current test item to test the next module. ABORT ALL---- Stop all the selected test items. User could use the hot key Ctrl+D to achieve the same operation. When the user calls ABORT ALL, the following message box will prompt for his selecting.
4. Title Bar: Title Bar located at the top of the window, it includes information as follows: Program Name and Its Version: Service Diagnostic Ver1.10; Test Module Name: Label the name and version of the test module. For example, in the above screen, the name of the test module is Memory Tester Build Date 2005.10.10. Status Bar: Located at the bottom of the screen as follows:
The status bar is used to indicate the current script setting and test status. It consists of two lines that includes the information as follows: Test Mode: TIMEBOUND or LOOPBOUND, e.g. LOOPBOUND in the above screen; Script File Name: Script file name, e.g. Quick.INI in the above screen; Current Time(C. TIME): Current system time, e.g. C.TIME:2006-07-05 09:21:27 in the above screen; Test Time Remaining (LEFT): In TIMEBOUND mode, it would display the remaining test time at the same location as Current TIME (C. TIME) in the above screen;
3.2 Quick Start
Current Loop Count: In LOOPBOUND mode, it will display the total LOOP number planning to execute and the current LOOP number have been finished, e.g. COUNT: 01/01 in the above screen; CPU Temperature: Detect the temperature in the current CPU, e.g. CPU: 49C in the above screen; Remaining Battery Capacity: Remaining Battery Capacity detected in the current Battery, e.g. BAT: 97%; Test Order: Define the test sequence. There is two sequence modes: Sequential Test Mode and Random Test Mode. The default mode is Sequential Test Mode, it would displays ORDER: SEQ as in the above screen; LOG File Name: Display the file name of the test log, e.g. Quick.Log in the above screen; Start Test Time (S.TIME): Display the test start time for the current test item or the test script, e.g. S.TIME: 2006-07-05 09:21:16 in the above screen; Break On Error: Display HALT as shown in the above screen when Break On Error is enabled; Wait On Error: Display WAIT as shown in the above screen when Wait On Error is enabled; Pause Enable: Display PAUSE when Pause Enable is enabled; Manual Interrupt Method: Display Esc: Break to tell the user how to manually interrupt the test process.
3.3Option
3.3
Options
3.3.1 Overview In Service Diagnostics, with the Options menu user can configure the batch parameters, test items parameters and those parameters created by the LOG file.
Options Menu Notes:

Select All/None Items
Switch between selecting all test items and selecting none. The hot key is F6.
Test Selected Items
Execute all selected test items in this editor. The hot key is F8. If Interactive option in batch parameters has not been selected, a warning message would be shown as below:
Edit Batch Parameters
3.3 Option
3 Diagnostic Programs Configure batch parameters and all the test items parameters.
Load Batch Parameters
Upload all the test items and the parameters to the *.ini file.
Save Batch Parameters
Save all the parameters and the test items that are configured in the editor to a specified file.
Log Parameters
Configure LOG parameters.

Specify LOG Viewer
Specify the viewer for the LOG file.

Display Error Log File
Load the LOG file viewer specified in the Specify Log Viewer to view the LOG file.
DOS Shell
Enter the DOS Shell and execute the DOS programs. You can also exit to the Service Diagnostics Editor by the command of EXIT.
Exit to DOS
Exit the Service Diagnostics Editor and back to DOS. 3.3.2 Batch Parameters Configuration The batch parameters configuration screen can be accessed through Service Diagnostics/OPTIONS -> EDIT BATCH PARAMETERS -> BATCH PARAMETERS:
3.3Option
Test Order Specify the order of the test items. Choose 'Sequence' to adopt the sequential mode; choose 'Random' to run the test items in random sequence.
Test Options Choose one of the following options:
Wait On Error Wait for further confirmation while an error occurs.
Break On Error Stop the test when a test item fails.
Pause Enable Pause at the end of each test items and wait for the user to response with the test items that requires the user to assist the test processes, such as the keystroke test.
Interactive If the item is enabled during the test, the test items that need user to response can run normally, such as Mouse test; If it is disabled, those test items will report FAIL. When the option here is enabled, it would affect all the test items while the same option in Item Parameters Configuration only affect that test item.
Monitor Battery Life Monitor the remaining battery capacity (percent).
3.3 Option 9 Monitor CPU Thermal Monitor the CPU temperature.
Test Mode
LOOPBOUND The chosen test items will run repeatedly according to the times specified in the 'Number of Loops'.
TIMEBOUND The chosen test items will run for an extent time specified in 'Time Limit Hrs' and 'Time Limit Min'.
Time Limit Hrs Specify the hours whether 'TIMEBOUND' is chosen under the batch mode.
Time Limit Min Specify the minutes whether 'TIMEBOUND' is chosen under the batch mode.
Number Of Loops Specify the repeating times when 'Loop Bound' is chosen under the batch mode.
3.3.3 Items Parameters Configuration The test items parameters configuration screen can be accessed through Service Diagnostics/Options -> Edit Batch Parameters -> Items Parameters-> System>CPU-> Basic Functionality:
Repeat count Repeat times of the test item.
3.3Option
Interactive If the item is enabled during the test, the test items that need user to response can run normally, such as PS2 Mouse test; If it is disabled, those test items will report FAIL. Whether the option here is enabled, it only affects the current test item.
Parameters For the test items with specific parameters, this option will call the related configuration screens. Otherwise, the program will show the following dialogue window:
Parameters for the specific test items: Some test items (Memory, HDD, e g...) have their individual parameters, which can be configured in their parameters setting window. 3.3.4 Load Batch Parameters Batch parameter is saved in the script file whose extension name is INI (*.INI). Below is the screen shot of Load Batch Parameters.
3.3 Option
In this window, you can specify the .INI files that you wanted to be edited or modified. 3.3.5 Save Batch Parameters Here you can save the edited or modified content to the batch parameters files.
3 Diagnostic Programs 3.3.6 LOG Parameters Setting
3.3Option
You can access the Log Parameters screen through Service Diagnostics\Options Generate Report.
Report Destination If selecting 'NONE', no log file will be generated; if selecting 'FILE', a log file with the name specified in 'Log File Name' will be generated.
Log Options Log Errors If selecting this parameter, errors will be recorded when the test fails.
Log Test Activities If selecting this parameter, the subtest results will be recorded.
Log Test Start Time If selecting this parameter, the start time of the test will be recorded.
Log Test End Time If selecting this parameter, the end time of the test will be recorded.
Log Errors Only If selecting this parameter, errors will be recorded only when the test fails.
Log Errors Only with Time
3.3 Option
3 Diagnostic Programs If selecting this parameter, errors and time will be recorded only when the test fails.
Append to Old Log File If selecting this parameter, the new log will be added to the old one.
Log Device Info on Fail If selecting this parameter, details of the failed test will be recorded.
Log file Name Specify the Log file name. You can input the detail path of the file. System will show the detail path of the file.
3.3.7 Specify LOG Viewer You can specify the Log file viewer in the Specify Log Viewer screen.
The default viewing program of Service Diagnostics is LogView.exe. 3.3.8 Display LOG File You can specify the Log file for viewing in the Display Error Log File screen.
3.3Option
In this screen, you can specify a Log file and view it with the viewer designated in Specify LOG Viewer. 3.3.9 LOG Viewer Service Diagnostic Log viewer:
, Scroll a line backward or forward on the screen.
Page Up, Page Down
3.3 Option Scroll a page backward or forward on the screen.
Esc Exit the Log viewer.
F1 Display the Help information about the Log viewer operations and the functional keys.
Ctrl+Home Go to the start of the log file.
Ctrl+End Go to the end of the log file.
Ctrl+F3 Prompt the search dialogue for the user to input the string to be looked for and specify the searching method.
F3 Find the next corresponding strings given.
3.3.10 LOG File Sample Log file is a test result file, which records the following information: Test module name, Test item name, Start/End time and the test result (including PASS, FAIL, SKIP and ABORT). When a failure is found, both the error code and the error information were recorded. In the Log file, we use Test Items as the test item name, which could not be modified in the whole time. And we use the Internal Name as name in the programs UI, which corresponds to the test item name and could be modified according to the users favorite. The following section is a sample of log file:
DIAG REPORT
<Module Name>: Service Diagnostic Ver 1.00 ... Memory Tester Build Date 2006.01.10 [Walk High] Begin Time: Wed Jul 05 10:45:36 2006
3 Diagnostic Programs Base Memory Test Extended Memory Test End Time: Wed Jul 05 10:47:51 2006 : PASS : PASS
3.3Option
<Module Name>: Service Diagnostic Ver 1.00 ... Mouse Test Build Date 2006.01.10 [MSTPad] Begin Time: Wed Jul 05 10:48:54 2006
Touch Pad Test ITEM TEST FAIL Function ID :502 Error Code :50202 Error Message :Touch Pad Test Fail End Time: Wed Jul 05 10:49:16 2006
: FAIL
3.4 Subtests
3.4
Subtests
Sub Subtest Item ID 01 CPU Test ID
Test Group System
Test items
Internal Name [CPUBasicFun] [CPUSpeed] Coprocessor [NPUFun] [NPUInterrupt] [CPUInformation] [Protect] [MMX] [DMACtrl] [Timer] [RealClock] [PCI] [PnP] [ACPI] [FANSpeed] [BIOSROM] [Parity]
01 Basic Functionality Test 02 CPU Speed Coprocessor 03 NPU Basic Functions NPU Interrupt 04 CPU Information 05 CPU Protected Mode 06 MMX
02
Board
01 DMA Controller 02 Interval Timer 03 Clock / Calendar 04 PCI System 05 Plug and Play 06 ACPI Test
03 Memory 01 02 03
FAN BIOS ROM
01 CPU Fan Speed Test
Parity
Pattern 01 Bit Stuck High Test 02 Bit Stuck Low Test 03 Checker Board Test 04 CAS Line Test 05 Incremental Test 06 Decremental Test 07 Incremental Decremental Test
[BSHigh] [BSLow] [ChkBd] [CASLine] [Incrment] [Decrment] [Idcrment] [XWRCycle] [XRCycle] [WalkHigh] [WalkLow] [Address] [Refresh] [CacheOne]
04 05 06 07 08 09 10
Extended Pattern Walking 1's Test Walking 0's Test Memory Address Refresh Test Cache Memory Random Memory
01 Write/Read Cycle Test 02 Read Cycle Test
01 Randomize Test
[Random]
3.4 Subtests
02 Random Increment Read/Write 11 12 Storage 01 Data Bus Test Memory Speed Test HDD
[RandIncr] [DataBus] [MemSpeed]
01 Sequential/Random R/W 02 Sequential/Random Seek 03 Performance 04 Controller Check 05 Diagnostic Read/Write 06 SMART Test
[SeqRdRW1] [Seek1] [Perform1] [Controller1] [DiagRW1] [SMART1] [CDRWController] [CDRWTransRate] [CDRWButterfly] [CDRWSeek] [CDRWSFSeek] [CDRWTray] [CharTest] [Attribut] [PageSel] [Color] [Text Mode] [VGAMode]
02
ODD
01 Controller Test 02 Data Transfer Rate 03 Data CD Butterfly Seek 04 Data CD Random Seek 05 Data CD Sequence Seek 06 Tray Eject Test
Video
01
Text Mode
01 Character Test 02 Text Attribute 03 Text Page Selection 04 Text Color 05 80*25 Text Mode
02
640*480 VGA Mode 640X480 Video Modes VESA 640x480x256 Mode VESA 640x480x32K Mode 01 VESA 640x480x64K Mode VESA 640x480x16K Mode VESA 640x480x32bit Mode 800X600 Video Modes VESA 800x600x256 Mode VESA 800x600x64K Mode 02 VESA 800x600x32K Mode VESA 800x600x16K Mode VESA 800x600x32bit Mode 1024X768 Video Modes VESA 1024x768x256 Mode VESA 1024x768x64K Mode 03 VESA 1024x768x32K Mode VESA 1024x768x16K Mode VESA 1024x768x32bit Mode
03
VESA Video Modes
[V640480_15] [V640480_16] [V640480_24] [V640480_32]
[V800600_15] [V800600_16] [V800600_24] [V800600_32]
[V1024768_15] [V1024768_16] [V1024768_24] [V1024768_32]
3.4 Subtests
1280X800 Video Modes VESA 1280x800x256 Mode VESA 1280x800x64K Mode 04 VESA 1280x800x32K Mode VESA 1280x800x16K Mode VESA 1280x800x32bit Mode 04 05 06 07 08 09 10 11 COMM 01 VESA Video Memory AGP Test LCD Panel Test Register Test Color Purity Test Direct Color Test DAC/Palette Address Bitblt Engine Test LAN Card
[V1280800_15] [V1280800_16] [V1280800_24] [V1280800_32] [VESAMEM] [AGP] [LCDPanel] [Register] [ColPurity] [DirectColor] [DACPalAddr] [Bitblt]
01 Device ID Detection 02 Vendor ID Detection 03 Mac Address Detection
[DeviceID] [VendorID] [MAC Address] [1394 R/W Test] [KBDataLn] [KBLED] [KBClokLn] [MSTpad]
02 Peripheral 01
1394 Keyboard
01 GUID Detection 01 Keyboard Data Line 02 Keyboard Led 03 Keyboard Clock Line
02
Mouse
01 TouchPad
3.5 System Test
3.5
System Test
Move arrow keys and press the Space key to select CPU test item from Service Diagnostic menu, then highlight CPU and press the Enter to run this test item. Subtest 01 CPU
1. Basic Functionality Test This test item is to check whether the CPU works normally through math and logic calculation, which means verifying the general registers, math registers and logic registers. 2. CPU Speed This test item is to detect the work frequency of the current CPU. User should change the parameters setting in the following window before the test:
3.5 System Test
CPU Speed Comparison--Whether you want to make a comparison of the CPU speed with the value set in Expected CPU Speed, you should choose Yes; otherwise, No. Expected CPU Speed--Specify the expected CPU Speed value you want for further comparison. Allowable Error Rate-- Specify the Allowable Error Rate value you want for further comparison. 3. Coprocessor 9 NPU Basic Functions Test This test item is to check whether the precision of the numeric processor in the float calculation is up to the IEEE standards. 9 NPU Interrupt Test This test item is to check whether NPU transfers the abnormal Interrupt program correctly by forcing an abnormal float. 4. CPU Information This test item is used for getting & showing CPU Information. It will be displayed as follows:
5. CPU Protected Mode Test This test item is to check whether CPU protected mode instruction works normally.
3 Diagnostic Programs 6. MMX
3.5 System Test
The test item is to confirm whether the CPU supports MMX instructions. Subtest 02 Boards 1. DMA Controller This test item is to check whether the DMA controller works normally. 2. Interval Timer This test item is to check whether the Interval Timer (18.2Hz, 55ms) works normally. 3. Clock/Calendar This test item is to check whether the system clock/calendar works normally. 4. PCI System This test item is to check whether the bus number, device number and function number in PCI bus are valid. 5. Plug and Play This test item is to check: 1. Whether the current system supports Plug-n-Play; 2. Whether there is an ESCD (Extended System Configuration Data) in the BIOS; 3. Whether there is PCI-to-ISA bridge in the system; 4. Whether there is PCI bus in the system. 6. ACPI Test ACPI test includes two sub-items as below: System Address Map Test: Check the correctness of ACPI system memory map, and whether its mapping scope is within real memory. ACPI Table Test: Check the correctness of ACPI relative configuration tables in the current system. Subtest 03 FAN Speed Test 1. CPU Fan Speed Test This test item is to check whether the CPU fan currently used works normally in the different speeds of stop, slow, middle and fast. Below is the
3.5 System Test parameter setting dialog window.
Set the range of Speed that is to be tested, then choose the OK button to test it. It will be displayed as follows:
3.6 Memory Test
3.6
Memory Test
This test module is to check whether the memory chip works normally. Subtest 01 BIOS ROM This test item is to check the validity of BIOS ROM that includes two sub-items -ROM Read and ROM Write Protection. ROM Read is to check whether BIOS ROM could be correctly read out, ROM Write Protect is to check whether BIOS ROM is write-protected. Subtest 02 Parity This test item is to check whether the parity checkout error could happen through writing and reading memory. Below is the parameter setting dialog window.
Test Option: Choose the Memory part to take the test Base Memory or Extended Memory. Extended Memory Test Range: Specify the test coverage range of Extended Memory. If user chooses Total Size, it means that the whole Extended Memory will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of Extended Memory will be taken according to the coverage range that user chooses or time. Extended Memory Start Address (MB) & Extended Memory End Address (MB): Set the range of extended memory that is to be tested, the test coverage would be based on the setting and the value in Percent (%) mentioned at below.
3.6 Memory Test
Pattern Size: Choose the pattern size BYTE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the memory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested. Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested. Subtest 03 Patterns This test item is to check whether the system memory includes base memory and extended memory that could be accessed correctly through writing and reading with a series of designed pattern data. Below is the parameter setting dialog window.
Test Option: Choose the Memory part to take the test Base Memory or Extended Memory. Extended Memory Test Range: Specify the test coverage range of Extended Memory. If user chooses Total Size, it means that the whole Extended Memory will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of Extended Memory will be taken according to the coverage range that user chooses or time. Extended Memory Start Address (MB) & Extended Memory End Address (MB): Set the range of extended memory that is to be tested, the test coverage would be based on the setting and the value in Percent (%) mentioned at below.
3.6 Memory Test
Pattern Size: Choose the pattern size BYTE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the memory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested. Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested. 1. Bit Stuck High Test Data pattern: Every bit is 1 (Each bit is high) 2. Bit Stuck Low Test Data pattern: Every bit is 0'(Each bit is low); 3. Checker Board Test Data pattern: Lo-byte and hi-byte are composed with 0101(0x5) and 1010 (0xA); 4. CAS Line Test Data pattern: Lo-byte and hi-byte are composed with 0000 (0x0) and 1111(0xF); 5. Incremental Test Data pattern: A series of increasing data from 0 by adding 1 each time; 6. Decrement Test Data Pattern: A series of decreasing data from the maximum (e.g. 0xFFFF) by subtracting 1 each time; 7. Incremental / Decrement Test Data Pattern is a series of data whose low byte is increasing data from 0x00 and high byte is decreasing data from 0xFF. Subtest 04 Extended Pattern
In addition to the above pattern test of the memory, there is Read/Write Cycle test and Read Cycle Test for the extended memory. Below is the parameter dialog window of the extended pattern test.
3.6 Memory Test
Test Range: Specify the test coverage range of Extended Memory. If user chooses Total Size, it means that the whole Extended Memory will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of Extended Memory will be taken according to the coverage range that user chooses or time. Extended Memory Start Address and Extended Memory End Address (MB): Set the range of extended memory that is to be tested. The test coverage will be according to the value setting in Percent (%) mentioned at below. Percent (%): Choose the percentage of the defined range of the memory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested; Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested. 1. Write/Read Cycle Test Test by using both read and write instructions. 2. Read Cycle Test Test by using read instructions. Subtest 05 Walking 1s Test The test item is to ensure that there is no short circuitry issue in memory chip. The parameter dialog window is the same as that in Subtest 02 Pattern. Subtest 06 Walking 0s Test
3.6 Memory Test
The test item is to ensure that there is no open circuitry issue in memory chip. The parameter dialog window is the same as that in Subtest 02 Pattern. Subtest 07 Memory Address This test item is to check short and open issue on memory address lines. Subtest 08 Refresh Test This test item is to check whether the memory refresh works normally. The parameter dialog window is as follows:
Subtest 09 Cache Memory The test item is to check whether the CPU internal cache memory could be accessed correctly. Subtest 10 Random Memory Random Memory test includes the following two test items: Randomize Test and Random Incremental Read/Write Test. The parameter dialog window is the same as that in Subtest 03 Extended Pattern. 1. Randomize Test This test item is to check whether the memory could be correctly accessed with randomized data and randomized memory address. 2. Random Increment Read/Write This test item is to check whether the memory could be correctly accessed with randomized memory address and a series of incremental data. Subtest 11 Data Bus Test This test item is to check whether the data bus works normally. Subtest 12 Memory Speed Test
3.6 Memory Test
This test item is to check the data-transferring rate for the cache memory and the system memory.
3.7 Storage
3.7
Storage
Subtest 01 HDD This test item runs on IDE hard disks. It checks the functions and performance of IDE hard disk. In order to protect users HDD data, the password must be verified before the HDD test. The screen is as follows:
Passwordhard disk 1. Sequential/Random R/W This test item is to check the HDDs Read/Write function through data writing and reading to HDD. This test item needs user to submit the parameters:
IDE HDD Test Range-- Specify the test coverage range of IDE HDD. If user chooses Total Size, it means that the whole IDE HDD will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of IDE HDD will be taken according to the coverage range that user chooses or time.
3.7 Storage
3 Diagnostic Programs LBA Start, LBA End--Specify the start and end byte in LBA (Large Block Address). PercentSpecify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested. Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested. Test ModeChoose test mode from the following options: (1) Read & Write Write data on the disk, then read it out and compare the two value; (2) Read Verify Read data only; (3) Unprotected WriteWrite data on the disk without backup original data. OptionSelect sequential test or random test
2. Sequential/Random Seek The test item is to check the correctness of the HDDs sectors seeking function. This test item involves the following parameters:
IDE HDD Test Rangeis same as the description of the upper item. LBA Start, LBA End-- specify start and finish byte in LBA(Large Block Address); Option-- Select sequential test or random test;
3 Diagnostic Programs Percent-- Specify the coverage rate in percentage of the total disk.
3.7 Storage
Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested; Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested. 3. Performance Check the HDDs seeking speed and transfer the data rate. 4. Controller Check Check the HDD controllers status, including HDD interrupt and unexpected interrupt. 5. Diagnostic Read/Write This test item is a quick test to verify whether the HDD could be correctly accessed and the user could specify the percentage in the below dialog.
Percent (1-100)-- Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested; Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested; 6. SMART Test SMART stands for Self-Monitoring, Analysis and Reporting Technology. SMART test will compare the attribute values with the threshold value in the HDDs controller to confirm whether there is any failure in the HDD Subtest 02 ODD
3.7 Storage
The ODD test runs on IDE CDROM/DVD-ROM & CD-RW. It will check the ODD drivers functionality and performance. 1. Controller Test Check the CDROM controllers status. 2. Data Transfer Rate Check the data transfer rate of the ODD drive. It will read data from the ODD disc and calculate the data transfer rate. This test needs a data CD. 3. Data CD Butterfly Seek Check the seek function of the ODD drive. It will perform a serial of seeking operations. First, locate the minimum LBA address, then the maximum, the subminimum, the sub-maximum and meet at center point. This test needs a data CD. 4. Data CD Random Seek Check the random seek function of ODD drive. Random access will reflect the performance of the heads random movement and seek. It tests for 1000 times. 5. Data CD Sequence Seek Check the sequential seek function of ODD drive. Perform location test to CDRW under LBA mode with the location address increasing in sequence. 6. Tray Eject Test Check the eject function of the ODD. It will eject the ODD and ask the user to confirm if the operation succeeds.
3.10 Peripheral
3.8
Video
This test item tests the video by: 1. 2. displaying the figures in different graphic modes. displaying the property and color of the characters in different text modes.
User will confirm whether each video mode works normally by judging whether the display is correct. It checks whether the video memory works normally by writing data into the video memory, then reading it out and comparing the two value. Subtest 01 Text Mode
1. Character Test Tests two types of font patterns. Font 9*14 Font 9*16 It requires the user to check whether all characters of each font type displayed correctly by answering the questions prompted on screen. It will be displayed as follows:.
2. Text Attribute This test item is to check whether the text attribute of normal, hi-intensity, inverse, and blinking in VGA text mode could be correctly displayed on the screen.
3.10 Peripheral
It would display the below texts of the different attributes in the screen: 1. 2. 3. 4. 5. 6. Text in normal attribute; Text in blinking normal attribute; Text in inverse attribute; Text in blinking inverse attribute; Text in hi-intensity attribute; Text in blinking hi-intensity attribute;
Users need to check whether all texts displayed correctly in the above six attributes and key in the answer Y or N to the prompts Is this display OK? [Y/N<Enter=Y>]. Below is the test screen of Text Attribute.
3. Text Page Selection This test item is to check whether the video memory could be correctly written and read in VGA text mode. According to the comparison of written data with read data, the program would report PASS or FAIL.
3.10 Peripheral
4. Text Color This test item is to check whether all 16 colors foreground and all 8 colors background works normally in VGA text mode. The bit4-6 of the attribute byte of a character defines 8 background colors (black, blue, green, cyan, red, brown, magenta, and light gray), and the bit0-3 defines 16 foreground colors (dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and white besides the above 8 colors). In the test, user is required to respond according to the instruction in the screen.
5. 80 * 25 Text Mode This test item is to check whether 80*25 Text Mode works normally.
3.10 Peripheral
In the test, user is required to respond according to the instruction in the screen.
Subtest 02
640 * 480 VGA Mode This test item is to check whether 680*480 VGA Text mode works normally. In the test, user is required to respond according to the instruction in the screen.
3 Diagnostic Programs Subtest 03 VESA Video Modes
3.10 Peripheral
This test item is to check whether all the video modes supported by the video card works normally. In the test, user is required to respond following the instruction in the screen. 1. 640X480 Video Modes Test
2. 800X600 Video Modes Test 3. 1024X768 Video Modes Test 4. 1280X800 Video Modes Test Subtest 04 VESA Video Memory This test item is to check whether VESA video memory could be correctly accessed (write data & read data). Below is the test items parameter dialog window:
3.10 Peripheral
If press Ctrl+Break to force the test to terminate during execution of VESA Video Memory, the test program will not operate and display properly in further tests. Subtest 05 AGP Test This test item is to report the systems Accelerated Graphics Port status and check whether AGP registers works normally. Subtest 06 LCD Panel Test This test item is to check whether there is any fault in its resolution by displaying the RGB gradient color screens.
3.10 Peripheral
Subtest 07
Register Test This test item is to check whether the registers of the video adapter works normally.
Subtest 08
Color Purity Test This test item is to check whether the system (the video adapter and the display) could display the purity color of red, green, blue, black and white. In the test, user is required to respond according to the instruction in the screen.
Subtest 09
Direct Color Test This test item is to check the video adapters composing ability of direct color in high and true color mode. In the test, user is required to respond according to the instruction in the screen.
3.10 Peripheral
Subtest 10
DAC/Palette Address This test item is to check the function of DAC registers and Palette registers. In the test, user is required to respond according to the instruction in the screen.
3.10 Peripheral
3.10 Peripheral
3.9
Communication (COMM)
LAN Card
Subtest 01
This test item is to check whether the module can detect the existence of the network card and display its related information. 1. Device ID Detection Detect the device ID of the network card. 2. Vendor ID Detection Detect the vendor ID of the network card. 3. MAC Address Detection Detect the MAC address of the network card.
Subtest 02
1394 GUID Detection This test item is used to read and display GUID from 1394 register.
3.10 Peripheral
3.10 Peripheral
Subtest 01 Keyboard
This test item is to check whether the keyboard works normally. 1. Keyboard Data Line Test Check whether the keyboard data line works normally. 2. Keyboard Led Test Check whether the keyboard led works normally. If Power switch\Volume\Caps\Num\Scroll\AVButton\DC-In\Power\Battery turn on with blue,click YES to continue,else click No.
3.10 Peripheral
If Power\Battery\Bridge\Wireless turn on with Orange,click YES to continue,else click No.
If Odd turn on with Orange,click YES to continue,else click No.
3.10 Peripheral
If HDD turn on with Orange,click YES to continue,else click No.
If all Keyboard LEDs Test normalIt will be displayed as follows:
3. Keyboard Clock Line Test Check whether the keyboard clock line works normally. Subtest 02 Mouse Test
Check whether the point devices work normally. 1. Touch Pad Before test Touch Pads function, user should set a timeout time at below screen:
3.10 Peripheral
At the below screen of Touch Pad test, user can press the left button, right button, and move the mouse to verify its functions for times, and the test will end either by user break or test time is out.
3.11Error Codes and Description
3.11 Error Codes and description

The format of Error Code is ddxxee, and dd is the device ID (1~2 chars), xx is test function ID of device (2 chars), ee is the error code of device (2 chars); the range of error code is from 01 to 99 in each device (the common error codes in all device are set to 99 and spanned).
Device ddxx Error Description Code ee Common Error 94 01xx 01 02 03 04 05 06 07 08 09 21 02xx 01 02 Interactive Mode Needed CPU CPU General Function Error CPU Arithmetic Error CPU Logic Error CPU Type Error CPU Speed Error NPU General Function Error NPU Interrupt Error CPU Information Error The CPU General Function register is damaged. Replace the CPU. Cause The test is not under interactive mode. Action Check whether the interactive test mode is adopted.
The CPU Arithmetic Register is As above. damaged. The CPU Logic Register is damaged. The CPU Type is not supportable. As above. Check whether the CPU is Intel CPU.
The CPU speed differs from the Check the CPU speed and the set expected value. expected speed. The NPU arithmetic unit is damaged. The NPU is damaged. Information of the CPU cannot be acquired. The CPU MMX register is damaged. The ROM BIOS has Physical problems. The ROM BIOS has Physical problems. Replace the CPU. As above. Check whether the CPU is Intel CPU. Replace the CPU. Replace the CPU.
Protected Instruction Error The CPU is damaged. MMX Test Error Memory Read Error Write-Protect Error
Test this unit on multiple machines. As above.
03
Base Memory Error Address
The test pattern read out from the base memory is different from Test this memory chip on the one that has been written in multiple machines. this address.
04 05 06 07 08
The test pattern read out from the extension memory is different As above. (XMS)Memory Problem from the one that has been written in this address. (XMS) Out Of Range Address Test Error Toggle Bit Error Interval Error Wrong parameters setup. Interference between different address channels. Errors with the timer chip. The acquired refreshing frequency is out of the estimated range. Check and reset the parameters. Test this memory chip on multiple machines. As above. Reset the estimated range.
09
L1 Cache test Error
The pattern read out from the L1 Cache is different from the one Test this unit on multiple that has been written in the same machines. address. Interference between different data channels. As above.
12 14 03xx 01
Data Bus Error Speed Error Board DMA Test Error
Failure during the transfer speed As above. test. DMA channel cannot transfer data normally. Repeat multiple times. Whether there is always the same error, replace the board.
04
Interval Timer Error
The difference between the actual precision of the interval timer and its theory value is out As above. of the permitted range. The timer counts imprecisely. The frequency is beyond the standard. The frequency is below the standard. R/W errors with the RTC refreshing interrupt controller. As above. As above. As above.
05 06 07
Periodic Faster Error Periodic Slower Error Update-ended Interrupt Error
08 13 14 15 16
RTC Alarm Error
The PC speaker's sound source --counter/timer 8253 cannot As above. produce corresponding timing signal. Check the board. As above. As above. Check PCI configuration on main board or PCI Device configuration.
PCI Bus Error No PCI. PCI Bus Scan Error PCI test fails. PCI Device Access Error PCI access fails. PCI Config Verification Error Wrong PCI configuration.
17 18 53 34xx 01 02 03 04xx 01 02 03 04
PCI to ISA Bridge Error ESCD Error ACPI Table Test Error FAN Fan Slow Speed Test Fail Fan Stop Test Fail Fan Fast Speed Test Fail Video Text Attribute Error
PCI-ISA bridge errors. ESCD errors. Errors with the ACPI table test. The fan slow speed test fails. The fan stop test fails. The fan fast speed test fails.
Repeat multiple times. If there is always the same error, replace the board. As above. As above. Check the FAN connection. As above. As above.
05
06 07
Check whether there is any Physical problems with the video physical problem with the video card. card. Text Page Selection Error As above. As above. Text Color Error As above. As above. Text Mode Error As above. As above. 1) Check whether there is any 1) Physical problems with the physical problem with the video video card. card. VGA Mode Error 2) Check whether there is any 2) Physical problems with the monitor. physical problem with the monitor. Check whether there is any Physical problems with the video Character Test Error physical problem with the video card. card. DAC/Palette Address Test As above. As above. Error Color Purity Test Error Check whether there is any Physical problems with the video physical problem with the video card or the monitor. card or the monitor. As above. As above. As above.
08
09 10 11 12 13 14 15
VESA Mode 15bits Direct As above. Color Test Error VESA Mode 16bits Direct As above. Color Test Error VESA Mode 24bits Direct As above. Color Test Error
Get the PCX graphics map Failure in getting PCX graphics Check for the PCX graphics map. Error map. Bitblt Engine Test Error VESA Video Memory Test Error VESA VRAM Test Error Physical problems with the video Check and see whether the video card. card has any physical problem. As above. As above.
Check whether there is any Physical problems with the video physical problem with the video card or the monitor. card or the monitor.
Check and see whether the AGP video card has any physical problem. Lower LCD color resolution. Replace the LCD. Physical problems with the video Check and see whether the video card. card has any physical problem. AGP configuration register errors.
16 17 19 20 21
AGP Test Error LCD Panel Test Error Register Test Error Adapter not support DDC
The video card doesn't support DDC. The monitor doesn't support Monitor not support DDC DDC. 1) Physical problems with the video card. 2) Physical problems with the monitor. As above. As above. As above. As above. As above. 1) Check and see whether the video card has any physical problem. 2) Check and see whether the monitor has any physical problem. As above. As above. As above. As above. As above. Check the Audio connection, replace the external fixture, and repeat the test. As above. Dont support PCI BIOS Please insert Net cad
21
8bits Text and Attribute Test Error
26 27 28 29 30 31xx 01 02 08xx 01 02
8bits Video Mode Test Error 15bits Video Mode Test Error 16bits Video Mode Test Error 24bits Video Mode Test Error 32bits Video Mode Test Error Audio Audio Play Fail Record Fail LAN Card PCI bus Error during device ID test PCI Ethernet card not present during device ID test Intel PCI Ethernet card not present during MAC test Keyboard Keyboard Map & Stroke Test Fail Clock Line Test Fail Data Line Test Fail
Cannot play music. Cannot record. Dont Scan PCI device
Dont find Net card
03 09xx 01 03 04
Dont found Net Card, This Card Please update net card or use cant be Read MAC by this other method method Keyboard Map & Stroke Test fails. Clock Line Test fails. Data Line Test fails. Check the KBD connection and repeat the test. As above. As above.
05xx 01 28xx 01 20xx 01 02 03 04 05 06 07 09 10 11 12 13 21xx 01 02 03 04 07 09 IDE-HDD Get Parameter Fail ! Write Pattern Error Data Compare Error Read Verify Error Seek Error Disk Controller Self Test Failed Disk Controller Test unexpected interrupt Failed Disk Controller action Test Failed Disk dos not support SMART Disk read attribute threshold error Disk read attribute value error Disk SMART attribute value error ODD No Disk in CDROM The Disk in CDROM is not Data Disk Mouse Touch Pad Test Fail 1394 Touch Pad Test Fail
Check the mouse connection and repeat the test.
Can not find IEEE1394 controller

Wrong test parameters are input by user. HD is damaged. HD is damaged. HD is damaged. HD is damaged. The HD controller is damaged. The HD controller is damaged. The HD controller is damaged. Disk dos not support SMART Disk read attribute threshold error Disk read attribute value error Disk SMART attribute value error No disk is found in the CDROM.
Dont support 1394.
Reinput the correct parameters. Send the HD for repair. As above. As above. As above. As above. As above. As above. Change HD which supported SMART and test again Send the HD for repair. As above. As above. Insert a disk into the CD-ROM.
The disk in the CD-ROM is not Insert a DATA CD. Data Disk. Send the CD-ROM for repair. Replace the disk or send the CDROM for repair.
IDE-CD Controller Error Functional errors with the CDROM. CD Read Error CD Seek Error Eject Error Either the disk or the CD-ROM is damaged.
Either the disk or the CD-ROM Replace the disk or send the CDis damaged. ROM for repair. Wrong CD-ROM drive. Exit from the wrong drive.
3.12 Quick Test Item List
3.12 Quick Test Item List

Device CPU Test Items Basic Functionality NPU Basic Functions CPU Information BIOS ROM Cache Memory Bit Stuck High Test Bit Stuck Low Test Address Test Interval Timer Clock / Calendar ACPI Test FAN Speed 1024X768 Video Modes Test: VESA 1024x768x64K Mode VESA 1024x768x32bit Mode VESA Video Memory Color Purity Test Direct Color Test LCD Panel Sequential/Random Read SMART Check Device ID Detection Vendor ID Detection Mac Address Detection Comment
Memory
10% or 3 minutes 10% or 3 minutes
Board
FAN Video
10% or 3 minutes
HDD LAN Card
25% or 3 minutes
Chapter 4 Replacement Procedures

4 1
4 Replacement Procedures
4-ii
Chapter 4 Contents
4.1 General....................................................................................................................... 4-1 Safety Precautions................................................................................................ 4-2 Before You Begin ................................................................................................ 4-4 Disassembly Procedures ...................................................................................... 4-5 Assembly Procedures........................................................................................... 4-5 Tools and Equipment ........................................................................................... 4-6 Screw Tightening Torque .................................................................................... 4-6 Colors of Screw Shanks ....................................................................................... 4-7 Symbols of Screws on the Computer Body ......................................................... 4-7 Symbol examples ................................................................................................. 4-7 Removing the Battery Pack ................................................................................. 4-8 Installing the Battery Pack................................................................................... 4-9 Removing the Optional PCI Express Card or PC Card ..................................... 4-10 Installing the Optional PCI Express Card or PC Card....................................... 4-11 Removing the Optional Momery Card .............................................................. 4-12 Installing the Optional Momery Card ................................................................ 4-13 Removing the Optional Memory ....................................................................... 4-14 Installing the Optional Memory......................................................................... 4-15 Removing the B-CAS card(for JP model only) or Smart Card ......................... 4-16 Installing the B-CAS card(for JP model only) or Smart Card ........................... 4-17 4.2 HDD......................................................................................................................... 4-18 Removing the HDD ........................................................................................... 4-18 Installing the HDD............................................................................................. 4-20 4.3 ODD Bay Module .................................................................................................... 4-21 Removing the ODD Bay Module (For Non-Tray Module) ............................... 4-21 Installing the ODD Bay Module (For Non-Tray Module) ................................ 4-22 Removing the ODD Bay Module (For Standard Module)................................. 4-23 Installing the ODD Bay Module (For Standard Module) .................................. 4-24
4-iii
Disassembling the ODD Bay Module................................................................ 4-25 Assembling the ODD Bay Module .................................................................... 4-26 4.4 Speaker Cover and Keyboard .................................................................................. 4-27 Removing the Speaker Cover and Keyboard..................................................... 4-27 Installing the Speaker Cover and Keyboard ...................................................... 4-29 4.5 Hotkey Board ........................................................................................................... 4-30 Removing the Switch Board .............................................................................. 4-30 Installing the Switch Board................................................................................ 4-31 4.6 MDC Module ........................................................................................................... 4-32 Removing the MDC Module ............................................................................. 4-32 Installing the MDC Module............................................................................... 4-33 4.7 Wireless LAN Card.................................................................................................. 4-34 Removing the Wireless LAN Card .................................................................... 4-34 Installing the Wireless LAN Card ..................................................................... 4-35 4.8 Robson Card............................................................................................................. 4-36 Removing the Robson Card ............................................................................... 4-36 Installing the Robson Card ................................................................................ 4-37 4.9 Display Assembly ..................................................................................................... 4-38 Removing the Display Assembly....................................................................... 4-38 Installing the Display Assembly ........................................................................ 4-39 4.10 Top Cover ................................................................................................................ 4-40 Removing the Top Cover................................................................................... 4-40 Installing the Top Cover .................................................................................... 4-42 4.11 System Board, AC IN cable..................................................................................... 4-43 Removing the System Board, AC IN cable ....................................................... 4-43 Installing the System Board, AC IN cable......................................................... 4-45 4.12 VGA Cooling Module and VGA Card (for VGA board Model Only).................... 4-46 Removing the VGA Cooling module and VGA Card (for VGA Board Model)4-46 Installing the VGA Cooling module and VGA Card (for VGA board Model) . 4-47 4.13 CPU Cooling Module and Fan................................................................................. 4-48 Removing the CPU Cooling module and Fan.................................................... 4-48 Installing the CPU Cooling module and Fan ..................................................... 4-49
4-iv
4.14
CPU.......................................................................................................................... 4-50 Removing the CPU ............................................................................................ 4-50 Installing the CPU.............................................................................................. 4-51
4.15
TV tuner ................................................................................................................... 4-53 Removing the TV tuner. ................................................................................ 4-53 Installing the TV tuner.. ..................................................................................... 4-54
4.16
Broadcom Card ........................................................................................................ 4-55 Removing the Broadcom Card........................................................................... 4-55 Installing the Broadcom Card ............................................................................ 4-56
4.17
USB cable, TV Tuner Splitter Card, Sub-Speaker and Audio Board...................... 4-57 Removing the USB cable, TV Tuner Splitter Card, Sub-Speaker and Audio Board ............................................................................................................ 4-57 Installing the USB cable, TV Tuner Splitter Card, Sub-Speaker and Audio Board ............................................................................................................ 4-58
4.18
Display Mask ........................................................................................................... 4-59 Removing the 15.4-inch LCD Display Mask .................................................... 4-59 Installing the 15.4-inch LCD Display Mask...................................................... 4-60
4.19
FL Inverter Board .................................................................................................... 4-61 Removing the FL Inverter Board....................................................................... 4-61 Installing the FL Inverter Board ........................................................................ 4-62
4.20
LCD Modules........................................................................................................... 4-63 Removing the 15.4-inch LCD module .............................................................. 4-63 Installing the 15.4-inch LCD Module................................................................ 4-65
4.21
CCD board and MIC................................................................................................ 4-66 Removing the CCD board and MIC .................................................................. 4-66 Installing the CCD board and MIC.................................................................... 4-67
4.22
FLICA card(for JAPANP Model Only), Bluetooth card and LED Board............... 4-68 Removing the FELICA card(for JAPANP Model Only) Bluetooth card and LED Board .................................................................................................. 4-68 Installing the FELICA card(for JAPANP Model Only) Bluetooth card and LED Board .................................................................................................. 4-69
4.23
Touch Pad and Button Board .................................................................................. 4-70 Removing the Touch Pad and Button Board .................................................... 4-70
4-v
Installing the Touch Pad and Button Board....................................................... 4-71 4.24 Speakers ................................................................................................................... 4-72 Removing the Speakers...................................................................................... 4-72 Installing the Speakers ....................................................................................... 4-72 4.25 Switch Board, Volume Board .................................................................................. 4-73 Removing the Switch Board, Volume Board .................................................... 4-73 Installing the Switch Board, Volume Board...................................................... 4-74 4.26 RJ11 cable, TV Antenna Connector and B-CAS Card Slot .................................... 4-75 Removing the RJ11 cable, TV Antenna Connector and B-CAS card slot ........ 4-75 Installing the RJ11 cable, TV Antenna Connector and B-CAS card slot .......... 4-76
4-vi
Figures Figure 4-1 Removing the battery pack.................................................................................. 4-8 Figure 4-2 Removing the PCI Express card or PC card ...................................................... 4-10 Figure 4-3 Removing the memory card .............................................................................. 4-12 Figure 4-4 Removing the optional memory........................................................................ 4-14 Figure 4-5 Removing the B-CAS card or smart card ......................................................... 4-16 Figure 4-6 Removing the HDD pack .................................................................................. 4-18 Figure 4-7 Removing the HDD chassis .............................................................................. 4-19 Figure 4-8 Removing the ODD bay module........................................................................ 4-21 Figure 4-9 Removing the ODD bay module........................................................................ 4-23 Figure 4-10 Removing the bracket from ODD drive.......................................................... 4-25 Figure 4-11 Removing the Bezel from ODD drive ............................................................ 4-26 Figure 4-12 Removing the Speaker cover .......................................................................... 4-27 Figure 4-13 Removing the keyboard .................................................................................. 4-28 Figure 4-14 Removing the hotkey board ............................................................................ 4-30 Figure 4-15 Removing the MDC module ........................................................................... 4-32 Figure 4-16 Removing the wireless LAN card ................................................................... 4-34 Figure 4-17 Removing the Robson card ............................................................................. 4-36 Figure 4-18 Removing the screws from the rear of the computer ...................................... 4-38 Figure 4-19 Removing the display assembly...................................................................... 4-39 Figure 4-20 Removing the screws from the back of the computer..................................... 4-40 Figure 4-21 Removing the top cover .................................................................................. 4-41 Figure 4-22 Removing the system board ............................................................................ 4-43 Figure 4-23 Removing the system board ............................................................................ 4-44 Figure 4-24 Removing VGA cooling module and VGA board .......................................... 4-46 Figure 4-25 Removing the CPU cooling module and fan................................................... 4-48 Figure 4-26 Applying silicon greases ................................................................................. 4-49 Figure 4-27 Removing the CPU ......................................................................................... 4-50 Figure 4-28 Installing the CPU ........................................................................................... 4-51 Figure 4-29 Installing the CPU ........................................................................................... 4-52 Figure 4-30 Removing the TV tunre.................................................................................... 4-53 Figure 4-31 Removing the broadcom card ......................................................................... 4-55
4-vii
Figure 4-32 Sub-speaker, USB cable, TV tuner splitter card and audio board .................. 4-57 Figure 4-33 Removing the display mask ............................................................................ 4-59 Figure 4-34 Removing the FL inverter board...................................................................... 4-61 Figure 4-35 Removing the15.4-inch LCD module and screws ........................................... 4-64 Figure 4-36 Removing the15.4-inch LCD module .............................................................. 4-64 Figure 4-37 Removing the CCD board and MIC................................................................. 4-66 Figure 4-38 Removing the FELICA card, bluetooth card and LED board......................... 4-68 Figure 4-39 Removing the touch pad and button board ..................................................... 4-70 Figure 4-40 Removing speakers .......................................................................................... 4-72 Figure 4-41 Removing the switch board and volume board................................................ 4-73 Figure 4-42 Removing the RJ11 cable, TV antenna connectoer and B-CAS card slot....... 4-75
4-viii
4.1 General
4 1
4.1
General
This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). Some replacement procedures may not require you to remove all the surrounding FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they should be removed in a top-down manner, irrespective of their physical locations. The FRUs shown in the top area of the chart should normally be removed before removing the FRUs shown in the bottom area. To replace the FRUs, first identify the suspect FRU for the system failure. Next, according to this chart, determine the FRUs that need to be removed before removing the suspect FRU. After you determine those FRUs, go to the appropriate sections according to the section numbers shown in the boxes. Then start removal and replacement.
4. 2 HDD 4. 4 Speaker cover and Keyboard
4. 5 Switch Board
4. 6 MDC Module
4. 7 Wireless LAN Card

4. 8 Display Assembly
4. 16 Display Mask
4. 3 ODD Bay Module
4. 17
4.9 Top Cover
FL Inverter Board
4. 18 CCD Board and MIC
4. 10 Speakers
4.11 USB and CRT Cable, Fingerprint Board and Bluetooth Card
4. 12 System Board, AC-IN cable and Fan 4. 19 LCD Modules

4. 13 VGA Card
4. 20 Touch Pad and Touch Pad Board
4. 14 Cooling Module
4. 15 CPU
How to use the chart (two examples): For removing the System Board: First, remove the top cover with the display assembly. Then, remove the HDD, selectable bay module, Bluetooth card, keyboard, and wireless LAN card, all of which are shown above the top cover with the display assembly. For removing the LCD Module: First, remove the display mask and FL inverter board, both of which are shown above the LCD module.
4. 2
HDD
4. 3 ODD Bay Module
4. 4 Speaker cover and Keyboard
4. 5 Switch Board
4. 7 Wireless LAN Card

4. 8 Display Assembly
4. 16 Display Mask
4. 6 MDC Module
4. 17
4.9 Top Cover
FL Inverter Board
4. 18 CCD Board and MIC

4. 10 Speakers
4.11 USB and CRT Cable, Fingerprint Board and Bluetooth Card
4. 12 System Board, AC-IN cable and Fan 4. 19 LCD Modules

4. 13 VGA Card
4. 20 Touch Pad and Touch Pad Board
4. 14 Cooling Module
4. 15 CPU
System Board LCD Module
4-1
4.1 General
Safety Precautions Before you begin to disassembly read the following safety precautions carefully. Be sure to follow them while you are working. DANGER: 1. Always use the genuine batteries or replacement batteries authorized by Toshiba. Batteries other than those differ in specifications and are incompatible with the computer. They may burst or explode. To avoid leakage of alkaline solutions, never heat or disassemble the battery packs. Never throw the battery packs into a fire. If this is violated, they will explode. The components such as the power supply and FL inverter carry high voltages. When you partially disassemble the computer and turn on the components, use extreme care not to touch the connectors and components to avoid the risk of electrical shock. Do not disassemble individual components during first-level maintenance.
2.
WARNING: 1. 2. To avoid the risk of electrical shock, turn the computer off and remove the AC adapter from the electrical outlet. Because the battery in the computer is left charged, the risk of electrical shock remains even after the AC adapter is removed from the electrical outlet. To avoid the risk of electrical shock, be sure to remove any metal jewelry or accessories such as necklaces, bracelets, and rings before starting work. Never work with damp or wet hands. To avoid personal injury, use care to avoid the sharp edges or corners of the components.
3.
4-2
4.1 General
CAUTION: 1. Before replacing a component, make sure that the replacement component meets the required specifications. To avoid computer failures, never use components that do not meet the specifications. To avoid internal damage such as short circuits and fire, never drop metal objects such as screws, pins, paper clips, etc. into the components. When a screw is removed, be sure to replace a screw that is the same size as the original screw. Make sure that all the screws are fastened securely. Loose screws can cause short circuits, overheating, smoke, or fire. Before raising a FRU or other component, make sure that all the component cables have been disconnected to avoid the risk of electrical shock caused by accidental contact with the energized components. For AC input, be sure to use the AC adapter and AC power cable that come with your computer or Toshiba-recommended equivalents. To avoid the risk of electrical shock, make sure that all the replacement components meet the specifications of the computer and that all the cables and connectors are fastened securely. Inside the PC are components that become hot during operation (such as the CPU and cooling module). To avoid burns, let the hot components cool down before starting inspection or repair task.
2.
3.
4. 5.
6.
4-3
4.1 General
Before You Begin Before you begin to disassembly the computer, keep in mind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack. Remove the optional parts and accessories as well. The procedures for removing the batteries will be explained later. Disassemble the computer only when an abnormality has occurred. Use only the recommended tools. To run and store the computer, be sure to prepare a working environment that is free from: Dust and contaminants Static electricity Extremely high or low temperatures and extremely high humidity
Run the diagnostic tests explained in Chapter 2 of this manual to identify the FRU that has probably caused the system failure. Perform only the required machine operations. Use only the disassembly and reinstallation procedures described in this manual. Place the removed components in a safe place away from the computer so that they are not damaged or get in the way of you doing your work. Normally, a number of screws need to be removed or replaced during disassembling. Place the removed screws in a safe place so that you can easily find the right screws for the right components. When assembling the computer, use the specified screws to fasten the parts to the specified locations. See the appropriate explanations and figures for screw sizes. To avoid personal injury, use care to handle components that have sharp edges or corners. After you have replaced a FRU, check that the FRU works correctly to ensure normal computer operation.
4-4
4.1 General
Disassembly Procedures The cable connectors come in these two basic types: Pressure plate connectors Normal pin connectors
To remove a pressure plate connector, pull up the tabs on either side of the connector's plastic pressure plate and gently pull the cable out of the connector. To reconnect the cable to the pressure plate's connector, raise the pressure plate up to a satisfactory height and slide the cable into the connector. Secure the cable in the correct position by pressing down the sides of the pressure plate so that the plate is flush with the sides of the connector. Grasp and pull the cable gently to check that the cable is connected firmly. If the cable comes off the connector, reinsert the cable by raising the pressure plate up to a satisfactory height. Normal pin connectors are used for all the other types of cables. These connectors can be installed or removed by simply inserting them or pulling them out.
Assembly Procedures You have to reassemble the computer after you have disassembled the computer and fixed the component that caused the problem. When reassembling the computer, keep the following general guidelines in mind: Take your time to carry out the suggested instructions completely. Hurried reassembly can often cause problems. Check that all the cable and connectors are fastened securely. Before securing the FRUs or other parts, check that the cables are not caught by the screws or FRUs. Check that all the latches are closed securely. Check that all the required screws are used to secure the FRUs. Using wrong screws can damage the threads or heads of the screws or does not ensure that the FRUs are secure.
After installing a FRU, make sure that the FRU and computer work normally.
4-5
4.1 General
Tools and Equipment For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipment. The proper use of this equipment will ensure successful repair work and reduce the costs for repairing damaged components. The equipment and tools required for disassembly and reassembly are: One 2 mm Phillips screwdriver One 4 mm flat-blade screwdriver Torx screwdriver Tweezers (for pulling out screws) ESD mats (for the floor and work desks) An ESD wrist strap or heel grounder Anti-static carpets or flooring Air ionizers (for highly electrostatic sensitive areas) A plastic card (in credit card size)
Screw Tightening Torque To secure screws, follow the torque values listed below. Over tightening can damage components and screws. Under tightening can loosen the screw or cause screws to come off, which may result in short circuits or other damage. M2 (2 mm) M2.5 (2.5 mm) M3 (3 mm) M2.5x4 PSP TITE screws 0.22 Nm (2.2 kgfcm) 0.36 Nm (3.5 kgfcm) 0.51 Nm (5.0 kgfcm) 0.204 Nm (2.0 kgfcm)
M2.5x6 GIZA TITE screws 0.36 Nm (3.5 kgfcm)
4-6
4.1 General
Colors of Screw Shanks For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows: Screws of an even-numbered length Brown Screws of an odd-numbered length White Screws of a special length Black Screws of a special length are those of a length having decimal places, such as 2.5 mm and 2.6 mm.
Symbols of Screws on the Computer Body For easy maintenance, the screw types are shown on the computer body as symbols. A symbol consists of a letter representing the screw type and a numeral representing the screw length. Screw type Bind screw Flat-head screw Super flat-head screw Tapping screw Other screws Letter B (stands for bind) F (stands for flat-head) S (stands for super flat-head) T (stands for tapping) U (stands for unique-pan head screws, studs, etc.)
Symbol examples 6 mm bind screw B6 12 mm bind screw B12 5 mm stud U5 (The numeral represents the rounded length of the threaded portion regardless of the entire stud length.)
4-7
4.1 General
Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4-1. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up their casing. 1. Turn the computer upside down so that the back is facing you. 2. Slide out the battery lock. 3. Slide the battery release latch and remove the battery pack from the computer.
battery pack
battery latch battery lock
Figure 4-1 Removing the battery pack
NOTE: Dispose of the used battery packs as required by local ordinances or regulations.
4-8
4.1 General
Installing the Battery Pack Install the battery pack according to the following procedures and Figure 4-1. CAUTION: The battery packs contain a lithium ion battery, which can explode due to improper replacement, use, handling, or disposal. Always dispose of the battery packs as required by local ordinances or regulations. Use only replacement batteries recommended by Toshiba.
NOTE: Visually check the battery's terminals. If they are dirty, clean them with a dry cloth. 1. Gently insert a new or recharged battery pack into place. Check that the battery release latch slides in and stops with a click. 2. Slide in the battery lock.
4-9
4.1 General
Removing the PCI Express Card or Optional PC Card Remove the optional PC card according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode. CAUTION: Install or remove the PC card correctly, according the manuals for the PC card and the operating system you are using. 1. Push the eject button for the PCI Express Card or PC card to be removed until it stops then release the button. 2. When the eject button pops out slightly, push it again. 3. When the PC card pops out, grasp it and pull it out.
PCI Express card or Optional PC card
Eject button
Figure 4-2 Removing the PCI Express Card or PC card
4-10
4.1 General
Installing the PCI Express Card or Optional PC Card Install the optional PC card according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode. 1. Insert the PC card gently until it stops and is seated securely. 2. After checking that the PC card is seated securely, push the PC card release lever slightly. After the PC card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card is compatible with the current hardware configuration.
4-11
4.1 General
Removing the Memory Card Remove the memory card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. 1. Open the card cover. 2. Push the memory card to be removed until it stops then release the memory card. 3. When the memory card pops out, grasp it and pull it out.
Memory card
Figure 4-3 Removing the memory card
4-12
4.1 General
Installing the Memory Card Install the memory card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. 1. Insert the memory card gently until it stops and is seated securely. 2. Checking that the memory card is seated securely. After the PC card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card is compatible with the current hardware configuration.
4-13
4.1 General
Removing the Optional Memory Remove the optional memory (module) according to the following procedures and Figures 44, after checking that the computer is turned off in boot mode. CAUTION: Remove the optional memory after turning off the computer. If this is violated, the computer or memory can be damaged. 1. Turn the computer upside down. 2. Release one optional memory cover securing the screw. 3. Remove the memory cover. CAUTION: Do not touch the connectors on the memory modules or in the computer. Contaminated connectors can cause memory access problems.
Memory cover
Nemory cover secure screw
Slot B Slot A Memory
Memory
Slot B Slot A
Stoper
Figure 4-4 Removing the optional memory 4. Spread out the two memory lock latches so that the memory module pops up. 5. Pull the memory module up and out at an angle, using care to avoid touching the connectors.
4-14
4.1 General
Installing the Optional Memory Install the optional memory (module) according to the following procedures and Figures 4-4, after checking that the computer is turned off in boot mode. Note: The slot A is reserved for main memory. Use the slot B for expanded memory. If only one card is installed, use the slot A. CAUTION: Install the optional memory after turning off the computer. If this is violated, the computer or memory can be damaged. 1. Insert the memory module into the connector at an angle of 45 degrees. 2. Press down on the memory module so that it is secured with both memory lock latches. 3. Reinstall the optional memory cover. 4. Secure the optional memory cover with the optional memory cover securing screw. After the computer is turned on, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the installed memory module has been recognized by the system. If it has not been recognized yet, check the connections.
4-15
4.1 General
Removing the B-CAS Card (For JAPAN model only) Remove the memory card according to the following procedures and Figure 4-5, after checking that the computer is turned off in boot mode. 1. Open the card cover. 2. Pull the B-CAS card to be removed, grasp it and pull it out.
M2x4 flat head screw B - CAS cover
B - CAS card or Smart card
Figure 4-5 Removing the B-CAS card
4-16
4.1 General
Installing the B-CAS Card (For JAPAN model only) Install the memory card according to the following procedures and Figure 4-5, after checking that the computer is turned off in boot mode. 1. Insert the B-CAS card gently until it stops and is seated securely. 2. Checking that the B-CAS card is seated securely. After the PC card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card is compatible with the current hardware configuration.
4-17
4.2 HDD
4.2
HDD
Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive.
Remove the HDD (hard disk drive) according to the following procedures and Figures 4-6, 47. 1. Remove the one M2x5 flat head screw HDD cover screws securing the HDD and one M2x4 flat head screw 2nd HDD cover. 2. Remove the HDD and 2nd HDD cover.
M2x4 flat head screw Second HDD cover
HDD pack
HDD pack M2x5 flat head screw HDD cover
Figure 4-6 Removing the HDD pack
4-18
4.2 HDD
3. Remove the HDD and 2nd HDD pack by pulling on the tab attached to the pack, following the direction of the arrows. NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or replace the HDD pack only if it fails. 4. Place the HDD pack on a flat surface (such as a desk), and remove the two M3x4 black flat head screws with M3x4 black head screws. 5. Place the HDD pack on a flat surface (such as a desk), and remove the chassis.
M3x4 black flat head screw HDD Chassis
M3x4 black flat head screw
HDD
Figure 4-7 Removing the HDD chassis CAUTION: Do not apply pressure to the top or bottom of the drive.
4-19
4.2 HDD
Installing the HDD Install the HDD according to the following procedures and Figures 4-6, 4-7. CAUTION: To avoid damage, always hold the HDD only by its sides. 1. Attach the HDD chassis. 2. Secure the HDD and its chassis with the two M3x4 black flat head screws with M3x4 white head screws. CAUTION: To prevent the HDD bracket from being distorted when installing the HDD pack into the computer, do not press the center of the HDD pack. Always hold the HDD pack by its sides. 3. Install the HDD pack into the correct position in the computer. Connect the HDD pack to the computer, holding the HDD pack by its sides. 4. Insert the HDD pack. 5. Secure the HDD cover by tightening the HDD cover screw.
4-20
4.3 ODD Bay Module
4.3
ODD Bay Module
Removing the ODD Bay Module (For Non-tray Module) NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules. Remove the ODD bay module according to the following procedures and Figures 4-8. 1. Turn the computer upside down. 2. Remove the two M2x4 black flat head screw. 3. Remove the ODD bezel. 4. Push out on the ODD bay module in the direction of the arrow. CAUTION: Handle the ODD bay module carefully it can become hot during operation.
Push hear
M2x4 flat head screw
ODD bay module
ODD bezel
Figure 4-8 Removing the ODD bay module
4-21
4.3 ODD Bay Module
Installing the ODD Bay Module (For Non-tray Module) Install the ODD bay module according to the following procedures and Figures 4-8. 1. Place the ODD bay module in the correct position and slide it in. 2. Push it in until it clicks into place. 3. Place the ODD bezel in the correct position. 4. Secure the ODD bay module with two M2x4 black flat head screw.
4-22
4.3 ODD Bay Module
Removing the ODD Bay Module (For Standard Module) NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules. Remove the ODD bay module according to the following procedures and Figures 4-9. 1. Turn the computer upside down. 2. Remove the two M2x4 black flat head screw. 3. Push out on the ODD bay module in the direction of the arrow. CAUTION: Handle the ODD bay module carefully it can become hot during operation.
Push hear
ODD bay module
Figure 4-9 Removing the ODD bay module
4-23
4.3 ODD Bay Module
Installing the ODD Bay Module (For Standard Module) Install the ODD bay module according to the following procedures and Figures 4-9. 1. Place the ODD bay module in the correct position and slide it in. 2. Push it in until it clicks into place. 3. Secure the ODD bay module with two M2x4 black flat head screw.
4-24
4.3 ODD Bay Module
Disassembling the ODD Drive NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails. Disassemble the ODD drive according to the following procedures and Figure 4-10, 4-11. 1. Remove four M2x3 black flat head screws. 2. Remove the bracket.
ODD bay module
Figure 4-10 Removing the bracket from the ODD drive 3. Release the following 4 latches on the ODD bezel 4. Remove the ODD bezel.
4-25
4.3 ODD Bay Module

ODD bezel
ODD bay module
Latch
Figure 4-11 Removing the Bezel from the ODD drive
Assembling the ODD Drive Assemble the ODD drive according to the following procedures and Figure 4-10, 4-11. 1. Place the ODD bezel in the correct position and secure the following 4 latches. 2. Seat the bracket and secure it with four M2x3 black flat-head screws.
4-26
4.4 Speaker Cover and Keyboard
4.4
Speaker Cover and Keyboard
Removing the Speaker Cover and Keyboard Remove the Speaker Cover and Keyboard according to the following procedures and Figure 4-12, 4-13. 1. Release the following 13 latches on the switch cover, in that order: - five bottom latches - two right and left latches - Six front latches 2. Remove the speaker cover.
Speaker cover
Latch
Figure 4-12 Removing the speaker cover
4-27
M2 . 5x2 . 6 black bin screw Keyboard
CN12
Figure 4-13 Removing the keyboard 3. Remove two M2.5x2.6 black bind securing screws. 4. Disconnect the keyboard cable from CN12 on the system board.
4-28
Installing the Speaker Cover and Keyboard Install the speaker cover and keyboard according to the following procedures and Figure 412, 4-13. 1. Connect the keyboard cable to CN12 on the system board. 2. Secure the keyboard with two M2.5x2.6 black bind screws. 3. Place the speaker cover in the correct position and secure the following 13 latches, in that order: - five bottom latches - two right and left latches - Six front latches
4-29
4.5 Hotkey Board
4.5 Hotkey Board

Removing the Hotkey Board Remove the Switch Cover and Switch Board according to the following procedures and Figures 4-14. 1. Disconnect the switch board flat cables from CN4 on the system board. 2. Remove two M2.5x3 white flat head screws. 3. Disconnect the switch board flat cables from CN5000 on the switch board.
Hotkey board Hotkey board flat cable
CN5000
CN4
Figure 4-14 Removing the hotkey board
4-30
4.5 Hotkey Board
Install the Hotkey Board Install the Hotkey board according to the following procedures and Figures 4-14. 1. Connect the hotkey board flat cables to CN5000 on the switch board. 2. Seat the switch board in the correct position. 3. Secure the switch board with two M2.5x3 white flat head screws. 4. Connect the switch board flat cables to CN4 on the system board.
4-31
4.6 MDC Module
4.6 MDC Module

Removing the MDC Module Remove the MDC Module (Modem Daughter Card) according to the following procedures and Figures 4-13, after checking that the computer is turned off in boot mode. CAUTION: Remove the MDC module after turning off the computer. If this is violated, the computer or MDC module can be damaged. 1. Remove the two M2x3 white bind screws securing the MDC module. 2. Left the MDC module and disconnect it from CN17 on the system board. 3. Disconnect the MDC cable from connector J2 on the MDC card.
CAUTION: Do not touch the connectors on the MDC module or in the computer. Contaminated connectors can cause MDC module failures.
M2x3 black bind screw J2 MDC card J1
CN17 MDCcable
Figure 4-15 Removing the MDC module
4-32
4.6 MDC Module
Installing the MDC Module Install the MDC module according to the following procedures and Figures 4-15, after checking that the computer is turned off in boot mode. CAUTION: Install the MDC module after turning off the computer. If this is violated, the computer or MDC module can be damaged.
CAUTION: Do not touch the connectors on the MDC module or in the computer. Contaminated connectors can cause MDC module failures. 1. Connect the MDC cable to connector J2 on the MDC module. 2. Connect the MDC module to CN17 on the system board. 3. Secure the MDC module with two M2x3 white bind screws. Note: After the computer is turned on, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the installed MDC module has been recognized by the system. If it has not been recognized yet, check the connections.
4-33
4 1
4.7 Wireless LAN Card

Removing the Wireless LAN Card Remove the wireless LAN card according to the following procedures and Figure 4-16.
CAUTION: Do not touch the connectors on the wireless LAN card and in the computer with your bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural oils, etc. from your hands. 1. Disconnect the three antenna cables with tweezers. 2. Remove the two M2x3 white bind screws securing the wireless LAN card. 3. Pull the wireless LAN card up and out at an angle.
White Antenna cable
Gray
M2x3 white bin screw Black
3 2
Wireless LAN card
Figure 4-16 Removing the wireless LAN card
4-34
Installing the Wireless LAN Card Install the wireless LAN card according to the following procedures and Figure 4-16. 1. Insert the wireless LAN card into the connector an angle of 45 degrees. 2. Press down on the wireless LAN card to secure it with two M2x3 white bind screws. 3. Connect the three antenna by pressing them firmly into place. CAUTION: Do not touch the connectors on the wireless LAN card and in the computer with your bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural oils, etc. from your hands.
4-35
4.8 Robson Card
4.8 Robson Card

Removing the Robson Card Remove the Robson card according to the following procedures and Figure 4-17.
CAUTION: Do not touch the connectors on the Robson card and in the computer with your bare hands. Robson cards can fail if they are contaminated with sweat, natural oils, etc. from your hands. 1. Remove the two M2x4 white bind screws securing the Robson card. 2. Pull the wireless Robson card up and out at an angle.
M2x4 white bin screw Robson card
Figure 4-17 Removing the Robson card
4-36
4.8 Robson Card
Installing the Robson Card Install the Robson card according to the following procedures and Figure 4-17. 1. Insert the Robson card into the connector an angle of 45 degrees. 2. Press down on the Robson card to secure it with two M2x4 white bind screws. CAUTION: Do not touch the connectors on the Robson card and in the computer with your bare hands. Robson card can fail if they are contaminated with sweat, natural oils, etc. from your hands.
4-37
4.9 Display Assembly

Removing the Display Assembly CAUTION: Use care to avoid that the antenna cable is not caught between the display assembly and computer. Remove the display assembly according to the following procedures and Figures 4-18, 4-19. 1. Turn the computer so the rear is facing you and remove two M2.5x8 black flat head screws. 2. Restore the normal computer placement and open the display panel.
M2 . 5x8 black flat head screw
Figure 4-18 Removing the screws from the back of the computer 3. Disconnect the LCD/FL cable from CN1 on the system board 4. Disconnect the MIC cable from CN5 and the CCD cable from CN6 on the system board 5. Remove four M2.5x5 white flat head screws securing the LCD module to the top cover. 6. Remove the wireless antenna cables, MIC cable and CCD cable from the top cover. 7. Remove the display module.
4-38
M2 . 5x5 white bind screw
LCD / FL cable CN1
MIC cable CCD cable CN5 CN6
Wireless LAN antenna
Figure 4-19 Removing the display assembly
Installing the Display Assembly Install the display assembly according to the following procedures and Figures 4-18, 4-19. 1. Place the display panel in the correct position and push the wireless antenna cable, MIC cable and CCD cable into the top cover. 2. Connect the LCD/FL cable to CN3, MIC cable to CN5 and CCD cable to CN6 on the system board. 3. Secure the display assembly with four M2.5x5 white flat head screws. 4. Close the display panel and turn the computer so the rear is facing you and secure two M2.5x8 black flat head screws.
4-39
4.10 Top Cover
4.10 Top Cover

Removing the Top Cover Remove the top cover according to the following procedures and Figures 4-20 and 4-21. 1. Turn the computer upside down and remove the following 14 screws: - fourteen M2.5x8 black bind screws
Figure 4-20 Removing the screws from the bottom of the computer 2. Turn the computer right side up. 3. Remove one M2.5x8 black flat head screw. 4. Disconnect the touch pad board flat cable from CN13. 5. Disconnect the Bluetooth cable from CN15. 6. Disconnect the FLICA flat cable from CN11. 7. Disconnect the LED board flat cable from CN1000. 8. . Disconnect the volume board flat cable from CN9.
4-40
4.10 Top Cover
9. Disconnect the switch board flat cable from CN16. 10. Disconnect the speaker cable from CN3. 11. Lift up the top cover.
Speaker cable M2 . 5x8 black flat head screw Volume board flat cable Touchpad flat cable Switch board flat cable
LED board flat cable FLICA flat cable CN9
Bluetooth card cable CN3
Latch
CN16
CN1000
CN11 CN15
CN13
Figure 4-21 Removing the top cover 12. Release the following 10 latches on the switch cover, in that order: - Three Left latches - Two right latches - Three front latches - two rear latches 13. Lift up the top cover.
4-41
4.10 Top Cover
Installing the Top Cover Install the top cover with the display assembly according to the following procedures and Figures 4-20, 4-21. 1. 2. Seat the top cover, adjusting its position. Secure the following 10 latches on the top cover, in that order: - Three Left latches - Two right latches - Three front latches - two rear latches Secure the top cover with one M2.5x8 black flat head screw. Connect the touch pad board flat cables CN13 on the system board. Connect the Bluetooth cable from CN15 on the system board.
3. 4. 5.
6. Connect the FLICA flat cable from CN11 on the system board. 7. Connect the LED board flat cable from CN1000 on the system board. 8. Connect the volume board flat cable from CN9 on the system board. 9. Connect the switch board flat cable from CN16 on the system board. 10. Connect the speaker cable from CN3 on the system board.. 11. Turn the computer upside down and secure it with the following 14 screws: - Eleven M2.5x8 black bind screws
4-42
4.11 System Board, AC-IN cable
4.11
System Board, AC-IN cable
Removing the System Board, AC-IN cable NOTE: Be careful of the eject button for the PC card. It can be damaged when removing the board. Make sure it is securely installed. Remove the System Board, MIC cable, AC-IN cable according to the following procedures and Figure 4-22. 1. Turn the computer upside down. 2. Disconnect the B-CAS card module flat cable from CN814. 3. Disconnect the audio board cable from PJ650. 2. Disconnect the TV splitter cable from CN16. 3. Disconnect the two TV antenna cables from TV tuner. 4. Turn the computer right side up. 5. Remove one M2.5x8 black flat head screw on the system board. 6. Remove the system board.
B - CAS card module flat cable Audio board cable
CN814 TV splitter cable CN16
PJ650 TV antenna TV antenna
Figure 4-22 Removing the system board
4-43

AC - IN cable
CN803
System board
M2 . 5x8 black flat head screw CN12 CN19 CN20
Audio board cable
Sub - speaker
USB connector cable
Figure 4-23 Removing the system board 7. Disconnect the audio board cable from CN18. 8. Disconnect the USB cable from CN20. 9. Disconnect the sub-speaker cable from CN12. 10. Remove the system board. 11. Turn the system board upside down. 12. Remove the AC-IN cable from CN803.
4-44
Installing the System Board, AC-IN cable Install the System Board, MIC cable, AC-IN cable according to the following procedures and figure 4-22, 4-23. NOTE: Be careful of the eject button for the PC card. It can be damaged when installing the system board. Make sure it is pushed in. 1. Turn the system board upside down and connect the AC-IN cable to CN803. 2. Seat the system board in the correct position. 3. Connect the USB cable to CN20, sub-speaker cable to CN12 and audio board cable to CN18 on the system board 4. Secure the system board with one M2x8 black flat-head screw. 5. Turn the computer upside down. 6. Connect the B-CAS card module flat cable to CN814, TV splitter cable to CN16 on the system board. 7. Connect the audio board cable to PJ650, TV antenna cable on the TV tuner.
4-45
4.12 VGA Cooling Module and VGA Board
4.12 VGA Cooling Module and VGA Board (for VGA Board Model)
Removing the VGA Cooling Module and VGA Board Remove the VGA Cooling Module and VGA Board according to the following procedures and Figure 4-22. 1. Remove two M2x5 black flat head screws. 2. Remove the VGA thermal module bracket. 3. Remove the VGA thermal module. 4. Remove two M2x3 black flat head screws form VGA board. 5. Remove the VGA board.
M2x5 black flat head screw VGA thermal module bracket VGA thermal module M2x3 black flat head screw VGA board
Figure 4-24 Removing the VGA Cooling Module and VGA Board
4-46
4.12 VGA Cooling Module and VGA Board
Installing the VGA Board Install the VGA board according to the following procedures and Figure 4-24. 1. Seat the VGA board. 2. Secure the VGA board with two M2x4 black flat head screws. 3. Secure the VGA board thermal module and VGA board bracket with one M2x4 black flat head screws.
4-47
4.13 CPU Cooling Module and Fan
4.13 CPU Cooling Module and Fan Removing the CPU Cooling Module and Fan CAUTION: When removing the cooling module, keep the following in mind: The cooling module can become very hot during operation. Be sure to let it cool down before starting the repair work. Do not touch or cause damage to the fan in the cooling module.
Remove the CPU cooling module and fan according to the following procedures and Figures 4-25, 4-26. 1. Remove two M2x4 black flat head screws on the north bridge bracket. 2. Remove the north bridge bracket. 3. Remove two M2x4 black flat head screws on the CPU thermal module bracket. 4. Remove the CPU bracket. 5. Remove the CPU cooling module. 6. Remove the one M2x4 black flat head screw. 7. Disconnect the fan cable form CN807and then remove the fan.
North bridge bracket CPU thermal module bracket CPU thermal module
Fan
System board CN807
Figure 4-25 Removing the CPU cooling module and fan
4-48
4.13 CPU Cooling Module and Fan
Figure 4-26 Applying silicon grease Installing the CPU Cooling Module and Fan Install the cooling Module according to the following procedures and Figures 4-25, 4-26. CAUTION: When installing the cooling module, keep the following in mind: 1. Be sure to confirm the correct position for the module. 2. Secure the relevant screws on the main board according to the number sequence sealed on the heat sink module.
NOTE: Apply silicon grease with a special syringe to cover the surface of the CPU chip completely. 1. If silicon grease is already applied to the CPU and fan module, wipe it off with a cloth. By using a special syringe, apply silicon grease G7762 to the CPU chip center so that the entire CPU chip is covered with the grease G7762. 2. Install the fan into the correct position in the computer and then connect the fan cable to CN807 on the system board. 3. Install the CPU cooling module into the correct position in the computer. 4. Seat the CPU cooling module and bracket in the correct position and secure them with two M2x4 black flat head screws. 5. Seat the north bridge bracket in the correct position and secure them with two M2x4 black flat head screws.
4-49
4.14 CPU
4.14 CPU Removing the CPU CAUTION: When removing the CPU, keep the following in mind: The CPU can become very hot during operation. Be sure to let it cool down before starting repair work. Remove the CPU according to the following procedures and Figures 4-27, 4-28 and 4-29. NOTE: FOXCONN CPU socket will be 180 degrees to the right. 1. Unlock the CPU by rotating the cam on the CPU socket 120 degrees to the left with a flat-blade screwdriver (in the order shown in the figure below). 2. Remove the CPU.
Figure4-27 Removing the CPU
4-50
4.14 CPU
Installing the CPU Install the CPU according to the following procedures and Figures 4-28, 4-29. 1. Check that the triangle on the cam is in the unlock position. 2. Attach the CPU to the correct position in the CPU socket. Align the CPU with the CPU socket by using the triangle as a guide.
Figure 4-28 Installing the CPU
CAUTION: Seat the CPU by aligning the triangle with the shaded area.
4-51
4.14 CPU
3. Secure the CPU by rotating the cam 120 degrees to the right with a flat-blade screwdriver. NOTE: FOXCONN CPU socket will be 180 degrees to the left.
Figure 4-29 Securing the CPU
4-52
4.15 TV Tuner
4.15 TV Tuner Removing the TV Tuner Remove the TV Tuner according to the following procedures and Figure 4-30.
CAUTION: Do not touch the connectors on the TV Tuner and in the computer with your bare hands. TV Tune can fail if they are contaminated with sweat, natural oils, etc. from your hands. 1. Remove the two M2x2 black bind screws securing the TV Tuner card. 2. Pull the wireless TV Tuner up and out at an angle.
TV tuner
Figure 4-30 Removing the TV Tuner
4-53
4.15 TV Tuner
Installing the TV Tuner Install the TV Tuner according to the following procedures and Figure 4-30. 1. Insert the TV Tuner into the connector an angle of 45 degrees. 2. Press down on the TV Tuner to secure it with two M2x2 white bind screws. CAUTION: Do not touch the connectors on the TV Tuner and in the computer with your bare hands. TV Tuner can fail if they are contaminated with sweat, natural oils, etc. from your hands.
4-54
4.16 Broadcom Card
4.16 Broadcom Card Removing the Broadcom Card Remove the Broadcom card according to the following procedures and Figure 4-31.
CAUTION: Do not touch the connectors on the Broadcom card and in the computer with your bare hands. Broadcom card can fail if they are contaminated with sweat, natural oils, etc. from your hands. 1. Remove the two M2x2 black bind screws securing the Broadcom card. 2. Pull the wireless Broadcom card up and out at an angle.
M2x3 black head screw
Broadcom card
Figure 4-31 Removing the Broadcom card
4-55
4.16 Broadcom Card
Installing the Broadcom Card Install the Broadcom card according to the following procedures and Figure 4-31. 1. Insert the Broadcom card into the connector an angle of 45 degrees. 2. Press down on the Broadcom card to secure it with two M2x2 white bind screws. CAUTION: Do not touch the connectors on the Broadcom card and in the computer with your bare hands. Broadcom card can fail if they are contaminated with sweat, natural oils, etc. from your hands.
4-56
4.17 Sub-speaker, USB cable, TV Tuner Splitter card Audio Board
4 Replacement Procedures and
4.17 Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board Removing the Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board Remove the Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board according to the following procedures and Figures 4-32. 1. Remove sub-speaker from base enclosure. 2. Remove two M2.5x4 white flat round-head screws securing the USB cable. 3. Remove the USB cable from base enclosure. 4. Remove two M2x3 black flat head screws securing the TV tuner splitter card 5. Remove TV antenna (L)/(S) and TV tuner splitter card cable on the TV tuner splitter card. 6. Remove the Audio board from base enclosure. 7. Remove audio board cable (L) from CN4000 and audio board cable (S) from CN4001 on the audio board.
Sub - speaker M2x3 black flat screw TV antenna ( L ) TV antenna ( S ) Audio cable ( L ) TV tuner splitter card cable TV tuner splitter card CN4000 Audio board CN4001 M2 . 5x4 white flat screw
USB cable Audio cable ( S )
Figure 4-32 Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board
4-57
4.17 Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board
Installing the Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board Install the Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board according to the following procedures and Figure 4-32. Note: Be careful of the kill switch button for the audio board. It can be damaged when installing the audio board. Make sure it is in the correct position. 1. Seat the audio board in the correct position and connect the audio board cable (L) to CN4000 and audio board cable (S) to CN4001 on the audio board. 2. Seat the TV tuner splitter card in the correct position and connect the TV tuner splitter card cable and TV antenna (L)/(S) on the TV tuner splitter card. 3. Secure the TV tuner splitter card with two M2x3 black flat head screws. 4. Seat the USB cable in the correct position. 5. Secure the USB cable with two M2.5x4 white flat head screws. 6. Seat the sub-speaker in the correct position.
4-58
4.18 Display Mask
4.18 Display Mask Removing the Display Mask Remove the display mask according to the following procedures and Figure 4-33. 1. Remove the following 4 seals on the display module in that order: - Two black seals on the bottom - Two black seals on the top 2. Remove the following 4 screws on the display module, in that order: - Two M2.5x5 white flat head screws on the top - Two M2.5x5 white flat head screws on bottom 3. Release the following 31 latches on the display mask, in that order: - Thirteen bottom latches - Five latches on each of the left and right sides - Eight top latches
Seal M2 . 5x4 white flat head screw Display mask
Seal M2 . 5x4 white flat head screw
Latch
Figure 4-33 Removing the display mask
4-59
4.18 Display Mask
Installing the Display Mask Install the display mask according to the following procedures and Figure 4-33. 1. Seat the display mask in the correct position and secure the following 31 latches, in that order: - Eight top latches - Five latches on each of the left and right sides - Thirteen bottom latches 2. Secure the display mask with the following 4 screws, in that order: - Two M2.5x4.5 white flat head screws on the top - Two M2.5x4.5 white flat head screws on bottom 3. Secure the following 4 seals to cover the screws, in that order: - Two black seals on the bottom - Two black seals on the top
4-60
4.19 FL Inverter Board
4.19 FL Inverter Board Removing the FL Inverter Board Remove the FL inverter board according to the following procedures and Figures 4-34. 1. Remove one M2.5x4 white flat head screw.
M2 . 5x4 white flat head screw FL inverter board
LCD / FL cable
HV cable
Figure 4-34 Removing the FL inverter board 2. Lift the LCD module, FL inverter board and disconnect the LCD/FL cable from the LCD/FL connector. 3. Disconnect the HV cable from the HV connector and remove the FL inverter board.
4-61
4.19 FL Inverter Board
Installing the FL Inverter Board Install the FL inverter board according to the following procedures and Figures 4-34. 1. Connect the LCD/FL cable to LCD/FL connector, and connect the HV cable to the HV connector. 2. Seat the LCD module, FL inverter board in the correct position. 3. Secure the FL inverter board with one M2.5x4 black flat head screw.
4-62
4.20 LCD Module
4.20
LCD Modules
NOTE: ICs are fragile. Use extreme care not to apply pressure to the ICs along the edges of the LCD module.
NOTE: Dispose of used LCD panels (fluorescent (FL) tubes) as required by local ordinances or regulations.
NOTE: The LCD/FL cable must be carefully peeled away before disconnecting it from the module.
Removing the 15.4-inch LCD module Remove the 15.4-inch LCD module according to the following procedures and Figures 4-35, 4-36. 1. Remove two M2.5x4 white flat head screws on each side securing the LCD bracket. 2. Carefully tilt the LCD module toward you. 3. Remove three M2x3 white flat head screws on each side securing the LCD bracket. 4. Remove the LCD brackets. 5. Turn the LCD upside down. Be sure to place it on a cushioned surface such as a foam pad.
4-63
4.20 LCD Module

M2 . 5x4 white flat head screw
LCD module
Right LCD bracket Left LCD bracket
Figure 4-35 Removing the 15.4-inch LCD module and screws 6. Remove the tape and LCD/FL cable connector. Then disconnect the LCD/FL cable.
Figure 4-36 Removing the 15.4-inch LCD module
4-64
4.20 LCD Module
Installing the 15.4-inch LCD Module NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module. Install the 15.4-inch LCD module according to the following procedures and Figures 4-35, 436. 1. Turn the LCD upside down. 2. Connect the LCD/FL cable to the LCD module connector. 3. Turn the LCD right side up. 4. Place the LCD bracket in the correct position and secure it with three M2x3 black flat head screws on each side. 5. Please the LCD module in the correct position and secure it with two M2.5x4 white flat heat screws on each side.
4-65
4.21 CCD Board and MIC
4.21 CCD Board and MIC Removing the CCD Board and MIC Remove the FL inverter board according to the following procedures and Figure 4-37. 1. Disconnect the CCD cable from the CCD module connector and remove the CCD board.
CCD board cable CCD board MIC
Figure 4-37 Removing the CCD board and MIC 2. Lift the MIC from the display rear cover.
4-66
4.21 CCD Board and MIC
Installing the CCD Board and MIC Install the FL inverter board according to the following procedures and Figure 4-37. 1. Connect the CCD module cable to CCD module connector. 2. Seat the CCD module, MIC in the correct position.
4-67
4.22 FELICA card, Bluetooth Card and LED Board
4.22 FELICA card(For JAPAN Model Only), Bluetooth card and LED Board Removing the FELICA card(For JAPAN Model Only), Bluetooth card and LED Board Remove the FELICA card(For JAPAN Model Only) and Bluetooth card and LED Board according to the following procedures and Figure 4-38. 1. Remove four M2x3 black flat head screws securing the LED board. 2. Remove the LED board. 3. Disconnect the LED flat cables from CN6003 on the LED board. 4. Remove four M2x3 black flat head screws securing the FELICA bracket. 5. Remove the FELICA card and Bluetooth card. 6. Disconnect the FELICA flat cables from FELICA card. 7. Disconnect the Bluetooth cable from Bluetooth card.
M2x3 black flat head bind screw
Felica card flat cable Felica card bracket Felica card Bluetooth card
Bluetooth card cable LED board flat cable CN6003
LED board
Figure 4-38 Removing the FLICA card, Bluetooth card and LED Board
4-68
4.22 FELICA card, Bluetooth Card and LED Board
Installing the FELICA card(For JAPAN Model Only), Bluetooth card and LED Board Install the touch pad and button board according to the following procedures and Figure 4-38. 1. Connect the FELICA card flat cable to FELICA card and Bluetooth card cable to Bluetooth card. 2. Seat the FELICA card, Bluetooth card and FELICA card bracket in the correct position and secure it with the four M2x3 black flat head screws. 3. Connect the LED board flat cable to CN6003 on the LED board. 4. Seat the LED board in the correct position and secure it with the tow M2x3 black flat head screws.
4-69
4.23 Touch Pad and Button Board
4.23 Touch Pad and Button Board Removing the Touch Pad and Button Board Remove the touch pad and button board according to the following procedures and Figure 439. 1. Disconnect the touch pad flat cables from J1 on the touch pad. 2. Disconnect the touch pad flat cable from CN3001 on the button board. 3. Disconnect the button board flat cables from CN3000 on the button board. 4. Remove the Mylar. 5. Remove five M2.5x4 black flat head bind screws and two M2x3 black flat head screws securing the touch pad. 6. Remove the touch pad bracket, button board and touch pad.
M2x3 black flat head bind screw
Mylar Touch pad bracket Touch pad J1 Touch pad cable CN3001 Button board CN3000 M2x3 black flat head screw Button board flat cable
Figure 4-39 Removing the touch pad and button board
4-70
4.23 Touch Pad and Button Board
Installing the Touch Pad and Button Board Install the touch pad and button board according to the following procedures and Figure 4-39. 1. Seat the touch pad, button board touch pad bracket in the correct position and secure it with the five M2x3 black flat head bind screws and two M2x3 black flat head screw. 2. Seat the Mylar in the correct position. 3. Connect the button board flat cable to CN3001 on the button board. 4. Connect the touch pad flat cables to J1 on the touch pad and CN3000 on the button board.
4-71
4.24 Speakers
4.24 Speakers Removing the Speakers Remove the Speakers according to the following procedures and Figure 4-40. 1. Remove one M2.5x4 white flat head screw securing the left speaker. 2. Remove two M2.5x4 white flat head screws securing the right speaker. 3. Remove the left and right speakers.
M2 . 5x4 white flat head screw Right speaker Left speaker Right speaker cable Left speaker cable
Figure 4-40 Removing the speakers
Installing the Speakers Install the speakers according to the following procedures and Figure 4-40. 1. Seat the left and right speaker in the correct position. 2. Route the speaker cable in the wire guide. 3. Secure the left speaker with one M2x4 white flat head screw. 4. Secure the right speaker with two M2x4 white flat head screws.
4-72
4.25 Switch Board and Volume Board
4.25 Switch Board and Volume Board Removing the Switch Board and Volume Board Remove the Switch Board and Volume Board according to the following procedures and Figures 4-41 1. Remove two M2x3 black flat head screws. 2. Remove the switch board. 3. Disconnect the switch board flat cables from CN8000 on the switch board. 4. Remove two M2x2 black flat head screws. 5. Remove the volume board. 6. Disconnect the volume board flat cables from CN7000 on the volume board.
M2x2 black flat head screw M2x3 black flat screw Volume board flat cable CN8000 Switch board flat cable Switch board
Volume board CN7000
Figure 4-41Rmoving the Switch Board and Volume Board
4-73
4.25 Switch Board and Volume Board
Install the Switch Board and Volume Board Install the switch board according to the following procedures and Figures 4-12. 1. Connect the switch board flat cables to CN8000 on the switch board. 2. Seat the switch board in the correct position. 3. Secure the switch board with two M2x3 black flat head screws. 4. Connect the volume board flat cables to CN8000 on the volume board 5. Seat the volume board in the correct position. 6. Secure the volume board with two M2x2 black flat head screws.
4-74
4.26 RJ11 Cable, TV Antenna Connector and B-CAS Card Slot 4 Replacement Procedures
4.26 RJ11 cable, TV Antenna Connector and B-CAS card Slot Removing the RJ11 cable, TV Antenna Connector and B-CAS card Slot Remove the RJ11 cable, TV Antenna Connector and B-CAS card Slot according to the following procedures and Figure 4-42. 1. Remove the RJ11 cable. 2. Remove one M2.5x4 white flat head screw securing the TV antenna connector. 3. Remove the TV antenna connector. 4. Remove four M2x3 black flat head screws securing the B-CAS card slot. 5. Remove the B-CAS card slot.
M2x3 black flat head screw M2x4 white flat head screw RJ11 cable
TV antenna connector
B - CAS card slot
Figure 4-42 Removing the RJ11 cable, TV Antenna Connector and BCAS card Slot
4-75
4 Replacement Procedures 4.26 RJ11 Cable, TV Antenna Connector and B-CAS Card Slot
Installing the RJ11 cable, TV Antenna Connector and B-CAS card Slot Install the RJ11 cable, TV Antenna Connector and B-CAS card Slot according to the following procedures and Figure 4-42. 1. Seat the B-CAS card slot in the correct position. 2. Secure the B-CAS card slot with four M2x3 black flat head screws. 3. Seat the TV antenna connector in the correct position. 4. Secure the l TV antenna connector with one M2.5x4 white flat head screw. 5. Seat the RJ11cable in the correct position. 6. Route the RJ11cable in the wire guide.
4-76
6000 1
Appendices
Apx. A Handling the LCD Module

Appendix A
Appendices
Appendix A Handling the LCD Module

Precautions for handling the LCD module
The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module:
1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained.
2. Be careful to align the four holes at the right side and left side of the LCD module with the corresponding holes in the LCD cover before securing the module with four screws. Do not force the module into place, because stress can affect its performance. Also, the panels polarized surface is easily scarred, so be carefully when handling it.
A-1
Appendices
3. If the panels surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panels surface. Do not apply cleanser directly to the panel. Also, never scratch the surface.
4. If water or other liquid is left on the panels surface for a long period, it can change the screens tint or stain it. Be sure to quickly wipe off any liquid.
A-2
Appendices
5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks.
6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module.
A-3
Appendices
7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods.
8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.
A-4
Appendices
9. Do not disassemble the LCD module. Disassembly can cause malfunctions.
10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panels polarization.
A-5
Apx. B Board Layout

Appendix B
Appendices
Appendix B Board Layout B.1 System Board Front View
Figure B-1 Board Layout (Front View)
B-1
Appendices
Apx. B Board Layout
B.2
System Board Back View
Figure B-2 Board Layout (Back View)
B-2
Appendices
Apx. C Pin Assignments
Appendix C C-3 C.1 C.2 C.3 C.4 C.5 C.6 C.7 C.8 C.9 C.10 C.11 C.12 C.13 C.14 C.15 C.16 C.17 C.18 C.19 C.20 C.21 C.22 C.23 C.24 C.25 C.26 C.27 C.28 C.29 C.30 C.31 CN1 CN2 CN3 CN4 CN5 CN6 CN7 CN8 CN9 CN11 CN12 CN13 CN15 CN16 CN17 CN18 CN19 CN20 CN800 CN801 CN802 CN803 CN806 CN807 CN808 CN809 CN810 CN811 CN812 CN813 CN814 LCM / FL Inverter Connector (40-Pin) ................................................. C-3 Speaker Sub-Woofer Connector (4-Pin)................................................ C-3 Internal Speaker Connector (4-Pin) ....................................................... C-4 Hot Key Board Connector (16-Pin)....................................................... C-4 Camera Module Connector (5-Pin) ....................................................... C-4 Internal Microphone Connector (2-Pin) ................................................ C-4 Robson Module Connector (52-Pin)...................................................... C-5 5 in 1 Memory Card Reader Connector (44-Pin) .................................. C-5 Volume Board Connector (8-Pin).......................................................... C-6 Felica Card Connector (6-Pin)............................................................... C-6 Internal Keyboard Connector (34-Pin) .................................................. C-7 USB Port8 M/B to IO/B Connector (16-Pin) ........................................ C-7 Blue Tooth Board Connector (10-Pin) .................................................. C-8 Hot Key Board Connector (16-Pin)....................................................... C-8 MODEM Board Connector (12-Pin) ..................................................... C-8 Wireless LAN Module Connector (52-Pin)........................................... C-9 Audio Board Connector (20-Pin)........................................................... C-9 USB Port2 / Port3 Connector (8-Pin) .................................................. C-10 SVIDEO Connector (4-Pin)................................................................. C-10 CRT Connector (15-Pin)...................................................................... C-10 HDMI Connector (19-Pin)................................................................... C-11 DC-IN Connector (6-Pin) .................................................................... C-11 USB Port0 / Port1 Connector (8-Pin) .................................................. C-11 FAN Connector (3-Pin) ....................................................................... C-12 DDR2 DIMM0 Socket (200-Pin) ........................................................ C-12 Express Card Connector (26-Pin)........................................................ C-15 PCMCIA Connector (68-Pin) .............................................................. C-15 DDR2 DIMM1 Socket (200-Pin) ........................................................ C-16 SATA HDD-2 Connector (22-Pin) ...................................................... C-19 Mini Card Connector (52-Pin)............................................................. C-19 BCAS Card Connector (10-Pin) .......................................................... C-20
C-1
Appendices
C.32 C.33 C.34 C.35 C.36 C.37 C.38 C.39 C.40 C.41 C.42 C.43 C.44 C.45 C.46 C.47 C.48 C.49 C.50 C.51 C.52
CN815 CN817 CN818 CN819 CN1000 CN2003 CN2009 CN3000 CN3001 CN4000 CN4001 CN5000 CN6003 CN7000
ODD Connector (50-Pin)......................................................................C-21 IEEE 1394 Connector (4-Pin)...............................................................C-21 SATA HDD-1 Connector (22-Pin).......................................................C-22 Battery Pack Connector (9-Pin)............................................................C-22 LED Board Connector (28-Pin)............................................................C-22 TV Tuner Master Connector (124-Pin) ................................................C-23 TV Tuner Slave Connector (124-Pin) ..................................................C-25 Touch Pad Board to Module Connector (12-Pin).................................C-27 USB Port8 IO/B to M/B Connector (16-Pin) .......................................C-27 TV Tuner Connector (8-Pin) ................................................................C-27 Audio Board to M/B Connector (20-Pin) .............................................C-27 Hot Key Board to M/B Connector (16-Pin) .........................................C-28 LED Board to M/B Connector (28-Pin) ...............................................C-28 Volume Board to M/B Connector (8-Pin) ............................................C-29
JACK800 IR Blaster-2 Connector (6-Pin) ............................................................C-29 JACK801 IR Blaster-1 Connector (6-Pin) ............................................................C-29 JACK802 RJ45 LAN Connector (12-Pin) ............................................................C-29 JACK4000 External Microphone Connector (6-Pin).............................................C-30 JACK4001 Line In Connector (6-Pin) ...................................................................C-30 JACK4002 Head Phone Connector (9-Pin) ...........................................................C-30 JACK4003 Video In Connector (6-Pin).................................................................C-31
C-2
Appendices
Appendix C
Appendix C
System Board C.1 CN1
Pin Assignments
LCM / FL Inverter Connector (40-Pin)
Table C-1 LCM / FL Inverter Connector Pin Assignments (40-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Signal Name DGND DGND DGND LVDS_TXDL0-_I LVDS_TXDL0+_I LVDS_TXDL2-_I LVDS_TXDL2+_I DGND LVDS_TXDU0-_I LVDS_TXDU0+_I LVDS_TXDU2-_I LVDS_TXDU2+_I DGND LCM_DDCPCLK_I N$813641 N$813641 N$813641 INV_PWM_3 DGND DGND I/O O O O O O O O O I/O O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Signal Name N$811968 N$811968 +V3S LVDS_TXDL1-_I LVDS_TXDL1+_I LVDS_TXCL-_I LVDS_TXCL+_I DGND LVDS_TXDU1-_I LVDS_TXDU1+_I LVDS_TXCU-_I LVDS_TXCU+_I DGND LCM_DDCPDATA_I N$813641 N$813641 N$813641 N$1181584 DGND DGND I/O O O O O O O O O O I/O -
C.2
CN2
Speaker Sub-Woofer Connector (4-Pin)
Table C-2 Speaker Sub-Woofer Connector Pin Assignments (4-Pin)

Pin No. 1 3 Signal Name SPK_SUBDGND I/O O Pin No. 2 4 Signal Name SPK_SUB+ DGND I/O O -
C-3
Appendices
C.3
CN3
Internal Speaker Connector (4-Pin)
Table C-3 Internal Speaker Connector Pin Assignments (4-Pin)

Pin No. 1 3 Signal Name SPK_OUT_LSPK_OUT_RI/O O O Pin No. 2 4 Signal Name SPK_OUT_L+ SPK_OUT_R+ I/O O O
C.4
CN4
Hot Key Board Connector (16-Pin)
Table C-4 Hot Key Board Connector Pin Assignments (16-Pin)

Pin No. 1 3 5 7 9 11 13 15 Signal Name SCAN_OUT(1) SCAN_OUT(2) SCAN_IN(7) SCAN_IN(4) SCAN_IN(1) TV_OUT MACHINE_ID0_DB DGND I/O O O I I I O O Pin No. 2 4 6 8 10 12 14 16 Signal Name SCAN_OUT(4) SCAN_IN(0) SCAN_IN(3) SCAN_IN(5) DOBLY N$1111693 MACHINE_ID1_DB DGND I/O O I I I O O -
C.5
CN5
Camera Module Connector (5-Pin)
Table C-5 Camera Module Connector Pin Assignments (5-Pin)

Pin No. 1 3 5 Signal Name +V5S_CAMERA USB_P7+ DGND I/O O I/O Pin No. 2 4 Signal Name USB_P7DGND I/O I/O -
C.6
CN6
Internal Microphone Connector (2-Pin)
Table C-6 Internal Microphone Connector Pin Assignments (2-Pin)

Pin No. 1 Signal Name ANAGND I/O Pin No. 2 Signal Name MIC_IN I/O I
C-4
Appendices
C.7
CN7
Robson Module Connector (52-Pin)
Table C-7 Robson Module Connector Pin Assignments (52-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 Signal Name DGND CLK_R_PCIE_MINI1# CLK_R_PCIE_MINI1 DGND DGND PCIE_C_RXN3 PCIE_C_RXP3 DGND DGND PCIE_C_TXN3 PCIE_C_TXP3 DGND I/O O O I I O O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 Signal Name +V3S DGND +V1.5S DGND BUF_PLT_RST# DGND +V1.5S DGND DGND +V1.5S DGND +V3S I/O O O O O O O
C.8
CN8
5 in 1 Memory Card Reader Connector (44-Pin)
Table C-8 5 in 1 Memory Card Reader Connector Pin Assignments (44-Pin)

Pin No. 1 3 Signal Name DGND MS_DATA1_SD_DAT1_SM_D1 I/O Pin No. I/O 2 4 Signal Name MS_BS_SD_CMD_SM_WEZ I/O I/O
MS_DATA0_SD_DAT0_SM_D0 I/O
C-5
Appendices
5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43
MS_DATA2_SD_DAT2_SM_D2 MS_DATA3_SD_DAT3_SM_D3 VCC_MC MS_DATA2_SD_DAT2_SM_D2 MS_BS_SD_CMD_SM_WEZ VCC_MC DGND MS_DATA0_SD_DAT0_SM_D0 SD_CDZ XD_CDZ SM_RBZ SD_WP_SM_CEZ SM_ALE N$1143854 MS_DATA0_SD_DAT0_SM_D0 MS_DATA2_SD_DAT2_SM_D2 SM_D4 SM_D6 VCC_MC SD_WP_SM_CEZ
I/O I/O O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44
MS_CDZ DGND DGND DGND DGND SM_REZ SM_CLE MS_BS_SD_CMD_SM_WEZ DGND
I/O I/O I/O I/O -
MS_CLK_SD_CLK_SM_ELWPZ I/O MS_DATA3_SD_DAT3_SM_D3 I/O MS_CLK_SD_CLK_SM_ELWPZ I/O MS_DATA1_SD_DAT1_SM_D1 I/O
MS_DATA1_SD_DAT1_SM_D1 I/O MS_DATA3_SD_DAT3_SM_D3 I/O SM_D5 SM_D7 DGND I/O I/O -
C.9
CN9
Volume Board Connector (8-Pin)
Table C-9 Volume Board Connector Pin Assignments (8-Pin)

Pin No. 1 3 5 7 Signal Name VOL_A VOL_B LED_DIMM#_BUFFER +VLED I/O I I O O Pin No. 2 4 6 8 Signal Name DGND DGND +VLED I/O O
C.10
CN11
Felica Card Connector (6-Pin)
Table C-10 Felica Card Connector Pin Assignments (6-Pin)

Pin No. 1 3 Signal Name +V5S_FELICA USB_P9+ I/O O I/O Pin No. 2 4 Signal Name USB_P9DGND I/O I/O -
C-6
Appendices
DGND
FILI_PRES#
C.11
CN12
Internal Keyboard Connector (34-Pin)
Table C-11 Internal Keyboard Connector Pin Assignments (34-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 Signal Name N$850859 N$850855 SCAN_IN(1) SCAN_IN(5) SCAN_IN(4) SCAN_IN(2) SCAN_OUT(3) SCAN_OUT(12) SCAN_OUT(14) SCAN_OUT(6) SCAN_OUT(9) SCAN_OUT(0) SCAN_OUT(15) SCAN_OUT(2) +V3S I/O I I O O O O I I I I I I I I O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 Signal Name N$850860 +V3S SCAN_IN(6) SCAN_IN(0) SCAN_IN(3) SCAN_IN(7) SCAN_OUT(7) SCAN_OUT(8) SCAN_OUT(10) SCAN_OUT(5) SCAN_OUT(11) SCAN_OUT(1) SCAN_OUT(13) SCAN_OUT(4) N$939833 +V3S I/O I O O O O O I I I I I I I I I O
C.12
CN13
USB Port8 M/B to IO/B Connector (16-Pin)
Table C-12 USB Port8 M/B to IO/B Connector Pin Assignments (16-Pin)
Pin No. 1 3 5 7 9 11 13 15 Signal Name DGND USB_P8IM_CLK_5 DGND +V3S +V5S DGND I/O O O O O Pin No. 2 4 6 8 10 12 14 16 Signal Name USB_P8+ DGND IM_DAT_5 +V3S +V5S DGND DGND I/O O O O O -
C-7
Appendices
C.13
CN15
Blue Tooth Board Connector (10-Pin)
Table C-13 Blue Tooth Board Connector Pin Assignments (10-Pin)

Pin No. 1 3 5 7 9 Signal Name DGND BTRF-E3V N$1192610 CH_CLK USB_R_P6+ I/O O I/O I/O Pin No. 2 4 6 8 10 Signal Name N$634761 CH_DATA BTMDL# USB_R_P6DGND I/O O I/O I I/O -
C.14
CN16
Hot Key Board Connector (16-Pin)
Table C-14 Hot Key Board Connector Pin Assignments (16-Pin)

Pin No. 1 3 5 7 9 11 13 15 Signal Name +VLED +V3LA LID_SW#_3 DGND SCAN_IN(7) SCAN_IN(5) SCAN_IN(2) I/O O O O O O O Pin No. 2 4 6 8 10 12 14 16 Signal Name +VLED DGND SCAN_OUT(13) SCAN_IN(6) SCAN_IN(3) SCAN_IN(1) I/O O O O O O
C.15
CN17
MODEM Board Connector (12-Pin)
Table C-15 MODEM Board Connector Pin Assignments (12-Pin)

Pin No. 1 3 5 7 9 11 Signal Name DGND MC97_3S_SDOUT DGND MC97_3S_SYNC N$737061 MC97_3S_RST# I/O I/O I/O I/O I/O Pin No. 2 4 6 8 10 12 Signal Name MDC DGND DGND MC97_3S_BITCLK I/O O I/O
C-8
Appendices
C.16
CN18
Wireless LAN Module Connector (52-Pin)
Table C-16 Wireless LAN Module Connector Pin Assignments (52-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 Signal Name PCIE_WAKE# CH_DATA CH_CLK CLKREQ_R_MINI2# DGND CLK_R_PCIE_MINI2# CLK_R_PCIE_MINI2 DGND BUF_PLT_RST# CLK_R3S_MINICARD2 DGND PCIE_C_RXN2 PCIE_C_RXP2 DGND DGND PCIE_C_TXN2 PCIE_C_TXP2 DGND I/O I/O I/O I/O I O O O O I I O O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 Signal Name +V3S DGND +V1.5S LPC_3S_FRAME# LPC_3S_AD(3) LPC_3S_AD(2) LPC_3S_AD(1) LPC_3S_AD(0) DGND WXMIT_OFF# BUF_PLT_RST# +V3A_WLAN DGND +V1.5S ICH_3A_ALERT_CLK ICH_3A_ALERT_DAT DGND DGND WLAN_LED# +V1.5S DGND +V3S I/O O O O O O O O O O O O I/O I/O I O O
C.17
CN19
Audio Board Connector (20-Pin)
Table C-17 Audio Board Connector Pin Assignments (20-Pin)

Pin No. 1 3 Signal Name +V5S SPDIF I/O O O Pin No. 2 4 Signal Name +V5S DGND I/O O -
C-9
Appendices
5 7 9 11 13 15 17 19
DGND HP_OUTL ANAGND MIC_L ANAGND LINE_L ANAGND KILL_SWCH#
O O O O
6 8 10 12 14 16 18 20
HPS HP_OUTR MICS MIC_R LINE_S LINE_R ANAGND +V3A
O O O O O O O
C.18
CN20
USB Port2 / Port3 Connector (8-Pin)
Table C-18 USB Port2 / Port3 Connector Pin Assignments (8-Pin)

Pin No. 1 3 5 7 Signal Name DGND USB_L_P2+ USB_VCC2 USB_L_P3+ I/O I/O O I/O Pin No. 2 4 6 8 Signal Name USB_L_P2USB_VCC2 USB_L_P3DGND I/O I/O O I/O -
C.19
CN800
SVIDEO Connector (4-Pin)
Table C-19 SVIDEO Connector Pin Assignments (4-Pin)

Pin No. 1 3 Signal Name DGND SVID_L_LUMA I/O O Pin No. 2 4 Signal Name DGND SVID_L_CHROMA I/O O
C.20
CN801
CRT Connector (15-Pin)
Table C-20 CRT Connector Pin Assignments (15-Pin)

Pin No. 1 3 5 7 9 11 13 Signal Name N$1091421 N$1091413 DGND DGND N$838148 HSYNC I/O O Pin No. 2 4 6 8 10 12 14 Signal Name N$1091416 DGND DGND DGND N$1163226 VSYNC I/O O
C-10
Appendices
15
N$838144
C.21
CN802
HDMI Connector (19-Pin)
Table C-21 HDMI Connector Pin Assignments (19-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 Signal Name N$1080927 DGND HDMI_SCLDDC DGND HDMI_L_TX0HDMI_L_TX0+ DGND HDMI_L_TX2HDMI_L_TX2+ I/O O O O O Pin No. 2 4 6 8 10 12 14 16 18 20 Signal Name N$988396 HDMI_SDADDC HDMI_L_TXCHDMI_L_TXC+ DGND HDMI_L_TX1HDMI_L_TX1+ DGND I/O O O O O O -
C.22
CN803
DC-IN Connector (6-Pin)
Table C-22 DC-IN Connector Pin Assignments (6-Pin)

Pin No. 1 3 5 Signal Name N$1158698 N$1158698 DGND I/O Pin No. 2 4 6 Signal Name N$1158698 DGND DGND I/O -
C.23
CN806
USB Port0 / Port1 Connector (8-Pin)
Table C-23 USB Port0 / Port1 Connector Pin Assignments (8-Pin)

Pin No. 1 3 5 7 Signal Name USBVCC1 USB_L_P1+ USBVCC1 USB_L_P0+ I/O O I/O O I/O Pin No. 2 4 6 8 Signal Name USB_L_P1DGND USB_L_P0DGND I/O I/O I/O -
C-11
Appendices
C.24
CN807
FAN Connector (3-Pin)
Table C-24 FAN Connector Pin Assignments (3-Pin)

Pin No. 1 3 Signal Name N$814474 FAN_TACH1 I/O O I Pin No. 2 Signal Name DGND I/O -
C.25
CN808
DDR2 DIMM0 Socket (200-Pin)
Table C-25 DDR2 DIMM0 Socket Pin Assignments (200-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 Signal Name M_VREF DGND M_DATA(0) M_DATA(1) DGND M_DQS#(0) M_DQS(0) DGND M_DATA(2) M_DATA(3) DGND M_DATA(8) M_DATA(9) DGND M_DQS#(1) M_DQS(1) DGND M_DATA(10) M_DATA(11) DGND DGND M_DATA(16) M_DATA(17) DGND M_DQS#(2) M_DQS(2) I/O O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 Signal Name DGND M_DATA(4) M_DATA(5) DGND M_DM(0) DGND M_DATA(6) M_DATA(7) DGND M_DATA(12) M_DATA(13) DGND M_DM(1) DGND M_CLK_DDR0 M_CLK_DDR0# DGND M_DATA(14) M_DATA(15) DGND DGND M_DATA(20) M_DATA(21) DGND PM_EXTTS#0 M_DM(2) I/O I/O I/O I I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I O
C-12
Appendices
53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101 103 105 107 109 111 113 115 117 119 121 123 125
DGND M_DATA(18) M_DATA(19) DGND M_DATA(24) M_DATA(25) DGND M_DM(3) DGND M_DATA(26) M_DATA(27) DGND M_CKE0 +V1.8 MA_BS2# +V1.8 M_A(12) M_A(9) M_A(8) +V1.8 M_A(5) M_A(3) M_A(1) +V1.8 M_A(10) MA_BS0# M_WE# +V1.8 M_CAS# M_CS1# +V1.8 M_ODT1 DGND M_DATA(32) M_DATA(33)
I/O I/O I/O I/O I/O I/O I/O O O O O I/O I/O I/O O I/O I/O I/O O I/O I/O I/O O O O O O I/O I/O
54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102 104 106 108 110 112 114 116 118 120 122 124 126
DGND M_DATA(22) M_DATA(23) DGND M_DATA(28) M_DATA(29) DGND M_DQS#(3) M_DQS(3) DGND M_DATA(30) M_DATA(31) DGND M_CKE1 +V1.8 M_A(14) +V1.8 M_A(11) M_A(7) M_A(6) +V1.8 M_A(4) M_A(2) M_A(0) +V1.8 MA_BS1# MA_RAS# M_CS0# +V1.8 M_ODT0 M_A(13) +V1.8 DGND M_DATA(36) M_DATA(37)
I/O I/O I/O I/O I/O I/O I/O I/O O O I/O O I/O I/O I/O O I/O I/O I/O O I/O I/O I/O O O O O I/O I/O
C-13
Appendices
127 129 131 133 135 137 139 141 143 145 147 149 151 153 155 157 159 161 163 165 167 169 171 173 175 177 179 181 183 185 187 189 191 193 195 197 199
DGND M_DQS#(4) M_DQS(4) DGND M_DATA(34) M_DATA(35) DGND M_DATA(40) M_DATA(41) DGND M_DM(5) DGND M_DATA(42) M_DATA(43) DGND M_DATA(48) M_DATA(49) DGND DGND M_DQS#(6) M_DQS(6) DGND M_DATA(50) M_DATA(51) DGND M_DATA(56) M_DATA(57) DGND M_DM(7) DGND M_DATA(58) M_DATA(59) DGND ICH_3S_SMDATA ICH_3S_SMCLK +V3S
I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O O I/O I/O I/O I/O O I/O I/O I/O I/O O
128 130 132 134 136 138 140 142 144 146 148 150 152 154 156 158 160 162 164 166 168 170 172 174 176 178 180 182 184 186 188 190 192 194 196 198 200
DGND M_DM(4) DGND M_DATA(38) M_DATA(39) DGND M_DATA(44) M_DATA(45) DGND M_DQS#(5) M_DQS(5) DGND M_DATA(46) M_DATA(47) DGND M_DATA(52) M_DATA(53) DGND M_CLK_DDR1 M_CLK_DDR1# DGND M_DM(6) DGND M_DATA(54) M_DATA(55) DGND M_DATA(60) M_DATA(61) DGND M_DQS#(7) M_DQS(7) DGND M_DATA(62) M_DATA(63) DGND N$860610 N$860611
I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O I I
C-14
Appendices
C.26
CN809
Express Card Connector (26-Pin)
Table C-26 Express Cad Connector Pin Assignments (26-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 Signal Name DGND USB_P4+ ICH_3A_ALERT_CLK +V1.5_EXP PCIE_WAKE# PERST# +V3_EXP CPPE# CLK_R_PCIE_CARD PCIE_C_RXN5 DGND PCIE_C_TXP5 I/O I/O I/O O I O O I O I O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 Signal Name USB_P4CPUSB# ICH_3A_ALERT_DAT +V1.5_EXP +V3AUX_EXP +V3_EXP EXPRESS_CLKREQ# CLK_R_PCIE_CARD# DGND PCIE_C_RXP5 PCIE_C_TXN5 DGND I/O I/O I I/O O O O O O I O -
C.27
CN810
PCMCIA Connector (68-Pin)
Table C-27 PCMCIA Connector Pin Assignments (68-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 Signal Name DGND ACARD_3S_AD1 ACARD_3S_AD5 ACARD_3S_CBE0# ACARD_3S_AD11 ACARD_3S_AD14 ACARD_3S_PAR ACARD_3S_GNT# ACARDVCC N$965384 ACARD_3S_CBE2# ACARD_3S_AD20 ACARD_3S_AD22 I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 Signal Name ACARD_3S_AD0 ACARD_3S_AD3 ACARD_3S_AD7 ACARD_3S_AD9 ACARD_3S_AD12 ACARD_3S_CBE1# ACARD_3S_PERR# ACARD_3S_INT# ACARDVPP ACARD_3S_IRDY# ACARD_3S_AD18 ACARD_3S_AD21 ACARD_3S_AD23 I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O
C-15
Appendices
27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67
ACARD_3S_AD24 ACARD_3S_AD26 ACARD_3S_AD29 ACARD_3S_CLKRUN# DGND ACARD_3S_AD2 ACARD_3S_AD6 ACARD_3S_AD8 ACARD_3S_VS1# ACARD_3S_AD15 ACARD_3S_A18_RFU ACARD_3S_STOP# ACARDVCC ACARD_3S_TRDY# ACARD_3S_AD17 ACARD_3S_VS2# ACARD_3S_SERR# ACARD_3S_CBE3# ACARD_3S_STSCHG ACARD_3S_AD30 ACARD_3S_CD2#
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O
28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68
ACARD_3S_AD25 ACARD_3S_AD27 ACARD_3S_D(2)_RFU DGND ACARD_3S_CD1# ACARD_3S_AD4 ACARD_3S_D(14)_RFU ACARD_3S_AD10 ACARD_3S_AD13 ACARD_3S_AD16 ACARD_3S_BLOCK# ACARD_3S_DEVSEL# ACARDVPP ACARD_3S_FRAME# ACARD_3S_AD19 ACARD_3S_RST# ACARD_3S_REQ# ACARD_3S_AUDIO ACARD_3S_AD28 ACARD_3S_AD31 DGND
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O -
C.28
CN811
DDR2 DIMM1 Socket (200-Pin)
Table C-28 DDR2 DIMM1 Socket Pin Assignments (200-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 Signal Name M_VREF DGND M_DATA(0) M_DATA(1) DGND M_DQS#(0) M_DQS(0) DGND M_DATA(2) M_DATA(3) I/O I/O I/O I/O O I/O I/O I/O Pin No. 2 4 6 8 10 12 14 16 18 20 Signal Name DGND M_DATA(4) M_DATA(5) DGND M_DM(0) DGND M_DATA(6) M_DATA(7) DGND M_DATA(12) I/O I/O I/O I/O I/O I/O
C-16
Appendices
21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93
DGND M_DATA(8) M_DATA(9) DGND M_DQS#(1) M_DQS(1) DGND M_DATA(10) M_DATA(11) DGND DGND M_DATA(16) M_DATA(17) DGND M_DQS#(2) M_DQS(2) DGND M_DATA(18) M_DATA(19) DGND M_DATA(24) M_DATA(25) DGND M_DM(3) DGND M_DATA(26) M_DATA(27) DGND M_CKE2 +V1.8 MB_BS2# +V1.8 M_A(12) M_A(9) M_A(8)
I/O I/O I/O I/O I/O I/O I/O I/O O O I/O I/O I/O I/O I/O I/O I/O O O O O I/O I/O I/O
22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94
M_DATA(13) DGND M_DM(1) DGND M_CLK_DDR2 M_CLK_DDR2# DGND M_DATA(14) M_DATA(15) DGND DGND M_DATA(20) M_DATA(21) DGND PM_EXTTS#1 M_DM(2) DGND M_DATA(22) M_DATA(23) DGND M_DATA(28) M_DATA(29) DGND M_DQS#(3) M_DQS(3) DGND M_DATA(30) M_DATA(31) DGND M_CKE3 +V1.8 M_A(14) +V1.8 M_A(11) M_A(7) M_A(6)
I/O O O O I/O I/O I/O I/O I O I/O I/O I/O I/O I/O O I/O I/O O O O O O O O
C-17
Appendices
95 97 99 101 103 105 107 109 111 113 115 117 119 121 123 125 127 129 131 133 135 137 139 141 143 145 147 149 151 153 155 157 159 161 163 165 167
+V1.8 M_A(5) M_A(3) M_A(1) +V1.8 M_A(10) M_A(15) M_WE# +V1.8 M_CAS# M_CS1# +V1.8 M_ODT3 DGND M_DATA(32) M_DATA(33) DGND M_DQS#(4) M_DQS(4) DGND M_DATA(34) M_DATA(35) DGND M_DATA(40) M_DATA(41) DGND M_DM(5) DGND M_DATA(42) M_DATA(43) DGND M_DATA(52) M_DATA(53) DGND DGND M_DQS#(6)
O I/O I/O I/O O I/O I/O I/O O O I/O O O I/O I/O O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
96 98 100 102 104 106 108 110 112 114 116 118 120 122 124 126 128 130 132 134 136 138 140 142 144 146 148 150 152 154 156 158 160 162 164 166 168
+V1.8 M_A(4) M_A(2) M_A(0) +V1.8 M_A(16) M_RAS# M_CS0# +V1.8 M_ODT2 M_A(13) +V1.8 DGND M_DATA(36) M_DATA(37) DGND M_DM(4) DGND M_DATA(38) M_DATA(39) DGND M_DATA(44) M_DATA(45) DGND M_DQS#(5) M_DQS(5) DGND M_DATA(46) M_DATA(47) DGND M_DATA(48) M_DATA(49) DGND M_CLK_DDR3 M_CLK_DDR3# DGND
O I/O I/O I/O O I/O I/O I/O O O O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O -
C-18
Appendices
169 171 173 175 177 179 181 183 185 187 189 191 193 195 197 199
M_DQS(6) DGND M_DATA(54) M_DATA(55) DGND M_DATA(56) M_DATA(57) DGND M_DM(7) DGND M_DATA(58) M_DATA(59) DGND ICH_3S_SMDATA ICH_3S_SMCLK +V3S
O I/O I/O I/O I/O I/O I/O I/O I/O I/O O
170 172 174 176 178 180 182 184 186 188 190 192 194 196 198 200
M_DM(6) DGND M_DATA(50) M_DATA(51) DGND M_DATA(60) M_DATA(61) DGND M_DQS#(7) M_DQS(7) DGND M_DATA(62) M_DATA(63) DGND N$860954 N$861284
I/O I/O I/O I/O I/O O O I/O I/O I O
C.29
CN812
SATA HDD-2 Connector (22-Pin)
Table C-29 SATA HDD-2 Connector Pin Assignments (22-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 Signal Name DGND SATA_C_TXN1 SATA_RXN1 DGND DGND DGND +V5S DGND DGND I/O O I O Pin No. 2 4 6 8 10 12 14 16 18 20 22 Signal Name SATA_C_TXP1 DGND SATA_C_RXP1 DGND +V5S +V5S I/O O I O O -
C.30
CN813
Mini Card Connector (52-Pin)
Table C-30 Mini Card Connector Pin Assignments (52-Pin)
C-19
Appendices
Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51
Signal Name PCIE_WAKE# DGND CLK_R_PCIE_MINI3# CLK_R_PCIE_MINI3 DGND DGND PCIE_C_RXN4 PCIE_C_RXP4 DGND DGND PCIE_C_TXN4 PCIE_C_TXP4 DGND DGND +V3S +V3S DGND -
I/O I/O O O I I O O O O I/O -
Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52
Signal Name +V3S DGND +V1.5S DGND BUF_PLT_RST# +V3A DGND +V1.5S ICH_3A_ALERT_CLK ICH_3A_ALERT_DAT DGND USB_P5USB_P5+ DGND +V1.5S DGND +V3S
I/O O O O O O I/O I/O I/O I/O O O
C.31
CN814
BCAS Card Connector (10-Pin)
Table C-31 BCAS Cad Connector Pin Assignments (10-Pin)

Pin No. 1 3 5 7 Signal Name BCASF-P5V XBCCLK-P5P DGND BCIO-P5P I/O O O O Pin No. 2 4 6 8 Signal Name BCRST-P5N I/O O -
C-20
Appendices
DGND
10
N$1057864
C.32
CN815
ODD Connector (50-Pin)
Table C-32 ODD Connector Pin Assignments (50-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 Signal Name N$630731 SDD(7) SDD(6) SDD(5) SDD(4) SDD(3) SDD(2) SDD(1) SDD(0) DGND PIDE_3S_IOW# PIDE_3S_IORDY PIDE_3S_IRQ SDA(1) SDA(0) PIDE_3S_CS#(0) +V5S +V5S DGND DGND N$630734 I/O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 Signal Name SDD(8) SDD(9) SDD(10) SDD(11) SDD(12) SDD(13) SDD(14) SDD(15) PIDE_3S_DREQ PIDE_3S_IOR# DGND PIDE_3S_DACK# SDA(2) PIDE_3S_CS#(1) +V5S +V5S +V5S DGND DGND DGND DISK_IN I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O O I
C.33
CN817
IEEE 1394 Connector (4-Pin)
Table C-33 IEEE 1394 Connector Pin Assignments (4-Pin)

Pin No. Signal Name I/O Pin No. Signal Name I/O
C-21
Appendices
1 3
1394_L_TPB0N 1394_L_TPA0N
I/O I/O
2 4
1394_L_TPB0P 1394_L_TPA0P
I/O I/O
C.34
CN818
SATA HDD-1 Connector (22-Pin)
Table C-34 SATA HDD-1 Connector Pin Assignments (22-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 Signal Name DGND SATA_C_TXN0 SATA_RXN0 DGND DGND DGND +V5S DGND DGND I/O O I O Pin No. 2 4 6 8 10 12 14 16 18 20 22 Signal Name SATA_C_TXP0 DGND SATA_C_RXP0 DGND +V5S +V5S I/O O I O O -
C.35
CN819
Battery Pack Connector (9-Pin)
Table C-35 Battery Pack Connector Pin Assignments (9-Pin)

Pin No. 1 3 5 7 9 Signal Name N$1040717 N$1188781 N$1003370 BATT_CLK DGND I/O I I I/O Pin No. 2 4 6 8 Signal Name N$1040717 DGND BATT_DATA DGND I/O I/O -
C.36
CN1000
LED Board Connector (28-Pin)
Table C-36 LED Board Connector Pin Assignments (28-Pin)

Pin No. 1 3 5 Signal Name +V5A +V3LA +V3 I/O O O O Pin No. 2 4 6 Signal Name +V5S +V3A +V3S I/O O O O
C-22
Appendices
7 9 11 13 15 17 19 21 23 25 27
DGND PWR_BUF_BLED# BAT0_BLED# HDD_LED# LED_6IN1 BTIFON# RESERVE_LED# +V5LA N$1184408 DGND
O O O O O O O -
8 10 12 14 16 18 20 22 24 26 28
DCIN_BLED# PWR_BUF_OLED# BAT0_OLED# ODD_LED# WLON# REC_LED DGND +V5LA CIR_OUT L_CIR_RX1 DGND
O O O O O O O O -
C.37
CN2003
TV Tuner Master Connector (124-Pin)
Table C-37 TV Tuner Master Connector Pin Assignments (124-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Signal Name TMA-P5V TMA-P5V TMA-P5V TMA_GND TMA_GND TMA_GND DGND PCI_3S_INTE# TM-P3V X33TU2-P3P DGND X33TU1-P3P DGND PCI_3S_REQ#(0) TM-P3V PCI_3S_AD(31) /PCI_3S_AD(29) DGND PCI_3S_AD(27) I/O O O O I O O O I O I/O I/O I/O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Signal Name TMA-P5V TMA-P5V TMA-P5V TMA_GND TMA_GND TMA_GND TMA-P5V PCI_3S_INTD# N$1051338 N$1051347 TM-P3V PCI_3S_GNT#(0) DGND PCI_3S_GNT#(1) PCI_3S_AD(30) TM-P3V I/O O O O O I O I/O I/O I/O O
C-23
Appendices
41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101 103 105 107 109 111 113
PCI_3S_AD(25) PCI_3S_REQ#(1) PCI_3S_CBE#(3) PCI_3S_AD(23) DGND PCI_3S_AD(21) PCI_3S_AD(19) DGND PCI_3S_AD(17) PCI_3S_CBE#(2) PCI_3S_IRDY# TM-P3V PCI_3S_CLKRUN# PCI_3S_SERR# DGND PCI_3S_PERR# PCI_3S_CBE#(1) PCI_3S_AD(14) DGND PCI_3S_AD(12) PCI_3S_AD(10) DGND PCI_3S_AD(8) PCI_3S_AD(7) TM-P3V PCI_3S_AD(5) BCRSTM-P3N PCI_3S_AD(3) +V5S PCI_3S_AD(1) DGND BCIO-P5P CPGP2M-P3P CPGP1M-P3P CPGP0M-P3P BCCDET-P3N DGND
I/O I I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O O I/O I/O I/O I/O I/O I/O -
42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102 104 106 108 110 112 114
PCI_3S_AD(28) PCI_3S_AD(26) PCI_3S_AD(24) N$1051321 DGND PCI_3S_AD(22) PCI_3S_AD(20) PCI_3S_PAR PCI_3S_AD(18) PCI_3S_AD(16) DGND PCI_3S_FRAME# PCI_3S_TRDY# PCI_3S_STOP# TM-P3V PCI_3S_DEVSEL# DGND PCI_3S_AD(15) PCI_3S_AD(13) PCI_3S_AD(11) DGND PCI_3S_AD(9) PCI_3S_CBE#(0) TM-P3V PCI_3S_AD(6) PCI_3S_AD(4) PCI_3S_AD(2) PCI_3S_AD(0) +V5S CPDETM-P3N KBC_AGND TV1-TPM0 TV1-TPM1 TV1-TPM2 TV1-TPM0 CPGP3M-P3P DGND
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O -
C-24
Appendices
115 117 119 121 123
XBCLKM-P3P DGND DGND BCPWON-P3P +V5S
I/O I/O O
116 118 120 122 124
DGND DGND DGND -
C.38
CN2009
TV Tuner Slave Connector (124-Pin)
Table C-38 TV Tuner Slave Connector Pin Assignments (124-Pin)

Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 Signal Name TSA-P5V TSA-P5V TSA-P5V TSA_GND TSA_GND TSA_GND DGND PCI_3S_INTE# TS-P3V X33TU4-P3P DGND X33TU3-P3P DGND PCI_3S_REQ#(3) TS-P3V PCI_3S_AD(31) /PCI_3S_AD(29) DGND PCI_3S_AD(27) PCI_3S_AD(25) PCI_3S_REQ#(1) PCI_3S_CBE#(3) PCI_3S_AD(23) DGND PCI_3S_AD(21) I/O O O O I O O O I O I/O I/O I/O I/O I I/O I/O I/O Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 Signal Name TSA-P5V TSA-P5V TSA-P5V TSA_GND TSA_GND TSA_GND TSA-P5V PCI_3S_INTF# N$1187079 N$1106904 TS-P3V PCI_3S_GNT#(3) DGND PCI_3S_GNT#(1) PCI_3S_AD(30) TS-P3V PCI_3S_AD(28) PCI_3S_AD(26) PCI_3S_AD(24) N$1106878 DGND PCI_3S_AD(22) I/O O O O O I O I/O I/O I/O O I/O I/O I/O I/O
C-25
Appendices
53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101 103 105 107 109 111 113 115 117 119 121 123
PCI_3S_AD(19) DGND PCI_3S_AD(17) PCI_3S_CBE#(2) PCI_3S_IRDY# TS-P3V PCI_3S_CLKRUN# PCI_3S_SERR# DGND PCI_3S_PERR# PCI_3S_CBE#(1) PCI_3S_AD(14) DGND PCI_3S_AD(12) PCI_3S_AD(10) DGND PCI_3S_AD(8) PCI_3S_AD(7) TS-P3V PCI_3S_AD(5) BCRSTM-P3N PCI_3S_AD(3) +V5S PCI_3S_AD(1) DGND BCIO-P5P CPGP2M-P3P CPGP1M-P3P CPGP0M-P3P BCCDET-P3N DGND XBCLKM-P3P DGND DGND BCPWON-P3P +V5S
I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O O
54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102 104 106 108 110 112 114 116 118 120 122 124
PCI_3S_AD(20) PCI_3S_PAR PCI_3S_AD(18) PCI_3S_AD(16) DGND PCI_3S_FRAME# PCI_3S_TRDY# PCI_3S_STOP# TS-P3V PCI_3S_DEVSEL# DGND PCI_3S_AD(15) PCI_3S_AD(13) PCI_3S_AD(11) DGND PCI_3S_AD(9) PCI_3S_CBE#(0) TS-P3V PCI_3S_AD(6) PCI_3S_AD(4) PCI_3S_AD(2) PCI_3S_AD(0) +V5S CPDETM-P3N KBC_AGND TV2-TPM0 TV2-TPM1 TV2-TPM2 TV2-TPM0 CPGP3M-P3P DGND DGND DGND DGND -
I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O -
C-26
Appendices
C.39
CN3000
Touch Pad Board to Module Connector (12-Pin)
Table C-39 Touch Pad Board to Module Connector Pin Assignments (12-Pin)
Pin No. 1 3 5 7 9 11 Signal Name LEFT_TP GND_TP IM_CLK_5_F N$1109478 I/O O I/O Pin No. 2 4 6 8 10 12 Signal Name RIGHT_TP GND_TP IM_DAT_5_FP N$1109478 I/O O I/O -
C.40
CN3001
USB Port8 IO/B to M/B Connector (16-Pin)
Table C-40 USB Port8 IO/B to M/B Connector Pin Assignments (16-Pin)
Pin No. 1 3 5 7 9 11 13 15 Signal Name GND_TP USB_P8-_FP IM_CLK_5_FP GND_TP +V3S_FP +V3S_FP GND_TP I/O O O O O Pin No. 2 4 6 8 10 12 14 16 Signal Name USB_P8+_FP GND_TP IM_DAT_5_FP +V3S_FP +V3S_FP GND_TP GND_TP I/O O O O O -
C.41
CN4000
TV Tuner Connector (8-Pin)
Table C-41 TV Tuner Connector Pin Assignments (8-Pin)

Pin No. 1 3 5 7 Signal Name TVGND TVGND TVGND I/O Pin No. 2 4 6 8 Signal Name EXCVB1-PXP EXINL-PXP EXINR-PXP TVGND I/O O O O -
C.42
CN4001
Audio Board to M/B Connector (20-Pin)
Table C-42 Audio Board to M/B Connector Pin Assignments (20-Pin)
C-27
Appendices
Pin No. 1 3 5 7 9 11 13 15 17 19
Signal Name +V5S_AB SPDIF_AB AUDIO_GROUND HP_OUTL_AB AGROUND_AUDIO MIC_L_AB AGROUND_AUDIO LINE_L_AB AGROUND_AUDIO KILL_SWCH#_AB
I/O O O O O O O
Pin No. 2 4 6 8 10 12 14 16 18 20
Signal Name +V5S_AB AUDIO_GROUND HPS_AB HP_OUTR_AB MICS_AB MIC_R_AB LINE_S_AB LINE_R_AB AGROUND_AUDIO +V3A_AB
I/O O O O O O O O O
C.43
CN5000
Hot Key Board to M/B Connector (16-Pin)
Table C-43 Hot Key Board to M/B Connector Pin Assignments (16-Pin)
Pin No. 1 3 5 7 9 11 13 15 Signal Name SCAN_HK_OUT(1) SCAN_HK_OUT(2) SCAN_HK_IN(7) SCAN_HK_IN(4) SCAN_HK_IN(1) TV_OUT_HK MACHINE_ID0_HK GROUND_H I/O O O I I I O O Pin No. 2 4 6 8 10 12 14 16 Signal Name SCAN_HK_OUT(4) SCAN_HK_IN(0) SCAN_HK_IN(3) SCAN_HK_IN(5) DOBLY_HK MACHINE_ID1_HK GROUND_H I/O O I I I O O -
C.44
CN6003
LED Board to M/B Connector (28-Pin)
Table C-44 LED Board to M/B Connector Pin Assignments (28-Pin)

Pin No. 1 3 5 7 9 11 13 Signal Name +V5A_LB +V3LA_LB +V3_LB LED_GROUND PWR_BUF_BLED#_DB BAT0_BLED#_DB HDD_LED#_DB I/O O O O O O O Pin No. 2 4 6 8 10 12 14 Signal Name +V5S_LB +V3A_LB +V3S_LB DCIN_BLED#_DB
PWR_BUF_OLED#_DB
I/O O O O O O O O
BAT0_OLED#_DB ODD_LED#_DB
C-28
Appendices
15 17 19 21 23 25 27
LED_6IN1_DB BTIFON#_DB RESERVE_LED#_DB +V5LA_LB N$1183960 LED_GROUND
O O O O -
16 18 20 22 24 26 28
WLON#_DB REC_LED_DB LED_GROUND +V5LA_LB CIR_OUT_LB L_CIR_RX1_LB LED_GROUND
O O O O O -
C.45
CN7000
Volume Board to M/B Connector (8-Pin)
Table C-45 Volume Board to M/B Connector Pin Assignments (8-Pin)

Pin No. 1 3 5 7 Signal Name +VLED_VL VL_GROUND VL_GROUND I/O O Pin No. 2 4 6 8 Signal Name +VLED_VL VOL_B_VL VOL_A_VL I/O O O O
C.46
JACK800 IR Blaster-2 Connector (6-Pin)
Table C-46 IR Blaster-2 Connector Pin Assignments (6-Pin)

Pin No. 1 3 5 Signal Name DGND DGND DGND I/O Pin No. 2 4 6 Signal Name N$1163015 IRTX2-DET# DGND I/O I -
C.47
JACK801 IR Blaster-1 Connector (6-Pin)
Table C-47 IR Blaster-1 Connector Pin Assignments (6-Pin)

Pin No. 1 3 5 Signal Name DGND DGND DGND I/O Pin No. 2 4 6 Signal Name N$1163007 IRTX1-DET# DGND I/O I -
C.48
JACK802 RJ45 LAN Connector (12-Pin)
Table C-48 RJ45 LAN Connector Pin Assignments (12-Pin)
C-29
Appendices
Pin No. 1 3 5 7 9 11
Signal Name TD+ RD+ LAN_45 LAN_78 N$637812 N$723050
I/O I/O I/O I/O I/O -
Pin No. 2 4 6 8 10 12
Signal Name TDLAN_45 RDLAN_78 LED_LANLINK# N$1167994
I/O I/O I/O I/O I/O I/O -
C.49
JACK4000 External Microphone Connector (6-Pin)
Table C-49 External Microphone Connector Pin Assignments (6-Pin)

Pin No. 1 3 5 Signal Name N$1099626 N$1099619 AGROUND_AUDIO I/O Pin No. 2 4 6 Signal Name N$1099621 MICS_AB I/O I/O -
C.50
JACK4001 Line In Connector (6-Pin)
Table C-50 Line In Connector Pin Assignments (6-Pin)

Pin No. 1 3 5 Signal Name AGROUND_AUDIO N$1099617 AGROUND_AUDIO I/O Pin No. 2 4 6 Signal Name N$1099615 LINE_S#_AB I/O I/O -
C.51
JACK4002 Head Phone Connector (9-Pin)
Table C-51 Head Phone Connector Pin Assignments (9-Pin)

Pin No. 1 3 5 7 9 Signal Name AUDIO_GROUND N$1183098 N$1099639 SPDIF_AB AUDIO_GROUND I/O I/O Pin No. 2 4 6 8 Signal Name N$1183097 HPS_AB +V5S_SPDIF_AB I/O I/O O
C-30
Appendices
C.52
JACK4003 Video In Connector (6-Pin)
Table C-52 Video In Connector Pin Assignments (6-Pin)

Pin No. 1 3 5 Signal Name EXCVB1-PXP N$1139473 I/O I Pin No. 2 4 6 Signal Name N$1139468 TVGND I/O -
C-31
Keyboard Scan/Character Codes

Apx. D Keyboard Scan/Character Codes
Appendices
Appendix D Keyboard Scan/Character Codes

Table D-1 Scan codes (set 1 and set 2) (1/4)
Cap No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 BkSp Tab Q W E R T Y U I O P [ { ] } 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B Keytop ~ 1 ! 2 @ 3 # 4 $ 5 % 6 ^ 7 & 8 * 9 ( 0 ) - _ = + Code set 1 Make 29 02 03 04 05 06 07 08 09 0A 0B 0C 0D Break A9 82 83 84 85 86 87 88 89 8A 8B 8C 8D Make 0E 16 1E 26 25 2E 36 3D 3E 46 45 4E 55 7D 66 0D 15 1D 24 2D 2C 35 3C 43 44 4D 54 5B F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 Code set 2 Break 0E 16 1E 26 25 2E 36 3D 3E 46 45 4E 55 7D 66 0D 15 1D 24 2D 2C 35 3C 43 44 4D 54 5B *2 *2 *2 *2 *2 *2 *2 *2 Note
D-1
Appendices

Cap No. 29 30 31 32 33 34 35 36 37 38 39 40 41 Keytop \ | Caps Lock A S D F G H J K L ; : Code set 1 Make 2B 3A 1E 1F 20 21 22 23 24 25 26 27 28 Break AB BA 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 Make 5D 58 1C 1B 23 2B 34 33 3B 42 4B 4C 52 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 Code set 2 Break 5D 58 1C 1B 23 2B 34 33 3B 42 4B 4C 52 *2 *2 *2 *2 *5 Note
43 44 45 46 47 48 49 50 51 52 53 54 55 56 57
Enter Shift (L) No.102 key Z X C V B N M , < . > / ? \_ Shift (R)
1C 2A 56 2C 2D 2E 2F 30 31 32 33 34 35
9C AA D6 AC AD AE AF B0 B1 B2 B3 B4 B5
5A 12 61 1A 22 21 2A 32 31 3A 41 49 4A 73
F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0
5A 12 61 1A 22 21 2A 32 31 3A 41 49 4A 73 59
*3
*2 *2 *2 *2
36
B6
59
D-2
Appendices

Cap No. 58 Keytop Ctrl Code set 1 Make 1D Break 9D Make 14 F0 Code set 2 Break 14 *3 Note
60 61 62
Alt (L) Space ALT (R) E0
38 39 38 E0
B8 B9 B8 E0
11 29 11
F0 F0 E0 F0
11 29 11
*3
75 76
Ins Del Home End PgUp PgDn
E0 E0
52 53
E0 E0
D2 D3
E0 E0
70 71
E0 E0
F0 F0
70 71
*1 *1
79 80 81
E0 E0 E0
4B 47 4F
E0 E0 E0
CB C7 CF
E0 E0 E0
6B 6C 69
E0 E0 E0
F0 F0 F0
6B 6C 69
*1 *1 *1
83 84 85 86
E0 E0 E0 E0
48 50 49 51
E0 E0 E0 E0
C8 D0 C9 D1
E0 E0 E0 E0
75 72 7D 7A
E0 E0 E0 E0
F0 F0 F0 F0
75 72 7D 7A
*1 *1 *1 *1
89
E0
4D
E0
CD
E0
74
E0
F0
74
*1
110 112 113 114 115 116 117 118 119 120 121
Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
01 3B 3C 3D 3E 3F 40 41 42 43 44
81 BB BC BD BE BF C0 C1 C2 C3 C4
76 05 06 04 0C 03 0B 83 0A 01 09
F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0
76 05 06 04 0C 03 0B 83 0A 01 09 *3
D-3
Appendices

Cap No. 122 123 124 126 202 203 204 205 206 207 Keytop F11 F12 57 58 Code set 1 Make D7 D8 *6 *7 5B 5D E0 E0 DB DD Break 78 7 *6 *7 E0 E0 70 79 7B 1F 2F Make F0 F0 *6 *7 E0 E0 F0 F0 F0 F0 F0 70 79 7B 1F 2F *8 *8 *8 Code set 2 Break 78 7 *3 *3 *6 *7 *4 Note
PrintSc *6 Pause Fn Win App Kat/Hir Hen Muh *7 E0 E0
Notes: 1. 2. 3. 4. 5. 6. 7. 8. * Scan codes differ by mode. * Scan codes differ by overlay function. * Combination with the Fn key makes different codes. * Fn key does not generate a code by itself. * This key corresponds to key No. 42 in a 102-key model. * Refer to Table D-6, No. 124 key scan code. * Refer to Table D-7, No. 126 key scan code. * 205~207 are for JAPAN keyboard only
D-4
Appendices
Table D-2 Scan codes with left Shift key

Cap No. 55 75 76 79 80 81 83 84 85 86 89 203 204 Key top / INS DEL Home End PgUp PgDn Win App E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 Make AA AA AA AA AA AA AA AA AA AA AA AA AA E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 35 52 53 4B 47 4F 48 50 49 51 4D 5B 5D E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 Code set 1 Break B5 D2 D3 CB C7 CF C8 D0 C9 D1 CD DB DD E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 Make 12 12 12 12 12 12 12 12 12 12 12 12 12 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 4A 70 71 6B 6C 69 75 72 7D 7A 74 1F 2F E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 Code set 2 Break 4A 70 71 6B 6C 69 75 72 7D 7A 74 1F 2F E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 12 12 12 12 12 12 12 12 12 12 12 12 12
Note : The table above shows scan codes with the left Shift key. In combination with the right Shift key, scan codes are changed as listed below: Set 1 Set 2 With left Shift E0 AA __________ E0 2A ___________ E0 F0 12 ________ E0 12 ___________ With right Shift E0 B6 E0 36 E0 F0 59 E0 59
D-5
Appendices
Table D-3 Scan codes in Numlock mode

Cap No. 75 76 79 80 81 83 84 85 86 89 203 204 Key top INS DEL Home End PgUp PgDn Win App E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 Make 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 52 53 4B 47 4F 48 50 49 51 4D 5B 5D E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 Code set 1 Break D2 D3 CB C7 CF C8 D0 C9 D1 CD DB DD E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 AA AA AA AA AA AA AA AA AA AA AA AA E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 Make 12 12 12 12 12 12 12 12 12 12 12 12 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 70 71 6B 6C 69 75 72 7D 7A 74 1F 2F E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 Code set 2 Break 70 71 6B 6C 69 75 72 7D 7A 74 1F 2F E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 E0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 12 12 12 12 12 12 12 12 12 12 12 12
Table D-4 Scan codes with Fn key

Cap No. 43 58 60 121 122 123 Keytop ENT CTRL LALT ARROW NUMERIC Scrl E0 E0 E0 45 45 46 Code set 1 Make 1C 1D 38 E0 E0 E0 Break 9C 9D B8 C5 C5 C5 E0 E0 E0 77 77 7E Make 5A 14 11 E0 E0 E0 F0 F0 F0 Code set 2 Break F0 F0 F0 77 77 7E 5A 14 11
D-6
Appendices
Table D-5 Scan codes in overlay mode

Cap No. 08 09 10 11 23 24 25 26 37 38 39 40 52 54 55 7 8 9 0 U I O P J K L ; M . / Keytop Make (7) (8) (9) (*) (4) (5) (6) () (1) (2) (3) (+) (0) (.) (/) E0 47 48 49 37 4B 4C 4D 4A 4F 50 51 4E 52 53 35 E0 Code set 1 Break C7 C8 C9 B7 CB CC CD CA CF D0 D1 CE D2 D3 B5 40 Make 6C 75 7D 7C 6B 73 74 7B 69 72 7A 79 70 71 4A F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 F0 E0 F0 Code set 2 Break 6C 75 7D 7C 6B 73 74 7B 69 72 7A 79 70 71 4A
Table D-6 No.124 key scan code

Key top Prt Sc Shift Make Common Ctrl + Shift + Alt + E0 2A E0 E0 E0 37 37 54 37 E0 Code set 1 Break B7 E0 E0 D4 E0 B7 B7 AA E0 Make 12 E0 E0 E0 7C 7C 84 7C E0 F0 E0 E0 F0 Code set 2 Break 7C F0 F0 B4 E0 7C 7C F0 12
D-7
Appendices
Table D-7 No.126 key scan code

Key top Pause Shift Code set 1 Make Common* E1 1D Ctrl* E0 46 45 E0 E1 C6 9D C5 E1 E0 14 7E 77 E0 Code set 2 Make E1 F0 F0 7E 14 F0 77
*: This key generates only make codes.
D-8
Apx. E Key Layout

Apx. E Key Layout
Appendices
Appendix E
E.1
Key Layout
United States (US) Keyboard
Figure E-1 US keyboard
E.2
Japan (JP) Keyboard
Figure E-2 JP keyboard
E-1
Appendices
Apx. E Key Layout
E.3
Spanish (SP) Keyboard
Figure E-3 SP keyboard
E.4
Korean (KR) Keyboard
Figure E-4 KR keyboard
E-2
Apx. E Key Layout
Appendices
E.5
Canadian Bilingual (QB) Keyboard
Figure E-5 QB keyboard
E.6
French (FR) Keyboard
Figure E-6 FR keyboard
E-3
Appendices
Apx. E Key Layout
E.7
German (GR) Keyboard
Figure E-7 GR keyboard
E.8
Italian (IT) Keyboard
Figure E-8 IT keyboard
E-4
Apx. E Key Layout
Appendices
E.9
Taiwan (TC) Keyboard
Figure E-9 TC keyboard
E.10 Portuguese (PT) Keyboard
Figure E-10 PT keyboard
E-5
Appendices
Apx. E Key Layout
E.11 DU, UE, US International (USE) Keyboard
Figure E-11 USE keyboard
E.12 Arabic (AR) Keyboard
Figure E-12 AR keyboard
E-6
Apx. E Key Layout
Appendices
E.13 Belgian (BE) Keyboard
Figure E-13 BE keyboard
E.14 Russian (RU) Keyboard
Figure E-14 RU keyboard
E-7
Appendices
Apx. E Key Layout
E.15 Swiss/Switzerland (SL) Keyboard
Figure E-15 SL keyboard
E.16 Swedish (SW) Keyboard
Figure E-16 SW keyboard
E-8
Apx. E Key Layout
Appendices
E.17 Norwegian (NO) Keyboard
Figure E-17 NO keyboard
E.18 Danish (DK) Keyboard
Figure E-18 DK keyboard
E-9
Appendices
Apx. E Key Layout
E.19 Turkey (TR) Keyboard
Figure E-19 TR keyboard
E.20 Greek (GK) Keyboard
Figure E-20 GK keyboard
E-10
Apx. E Key Layout
Appendices
E.21 Canadian Multinational (CM) Keyboard
Figure E-21 CM keyboard
E.22 Herbrew (HE) Keyboard
Figure E-22 HE keyboard
E-11
Appendices
Apx. E Key Layout
E.23 Czech (CZ) Keyboard
Figure E-23 CZ keyboard
E.24 Scandinavian (N5) Keyboard
Figure E-24 N5 keyboard
E-12
Apx. E Key Layout
Appendices
E.25 Hungary (HU) Keyboard
Figure E-25 HU keyboard
E.26 Slovakian (SK) Keyboard
Figure E-26 SK keyboard
E-13
Appendices
Apx. E Key Layout
E.27 Yugoslavia (YU) Keyboard
Figure E-27 YU keyboard
E.28 Thai (TH) Keyboard
Figure E-28 TH keyboard
E-14
Apx. E Key Layout
Appendices
E.29 United Kingdom (EN) Keyboard
Figure E-29 EN keyboard
E.30 Turkish F (TF) Keyboard
Figure E-30 TF keyboard
E-15
Apx. F BIOS Rewrite Procedures

Appendix G
Appendices
Appendix F
BIOS Rewrite Procedures
This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool: BIOS/EC/KBC rewriting disk for the computer that has renewed BIOS data. Rewriting the BIOS 1. Set the system to boot mode. 2. Turn off the power to the computer. 3. Remove the external cable and PC card. 4. Connect an external FDD and insert the BIOS/EC/KBC rewriting disk into either the external FDD. 5. Turn on the power while holding down the [`~] key (on the left of the space key). (Keep holding down the key until a message appears on the screen.) The BIOS rewriting starts. 6. When the process is completed, eject the BIOS/EC/KBC rewriting disk and the system is automatically reset.
F-1
Apx. G EC/KBC Rewrite Procedures

Appendix H
Appendices
Appendix G EC/KBC Rewrite Procedures

This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system.
Tools
To rewrite the EC/KBC, you need the following tool: BIOS/EC/KBC rewriting disk for the computer
Rewriting the EC/KBC

1. Set the system to boot mode. 2. Turn off the power to the computer. 3. Remove the external cable and PC Card. 4. Connect an external FDD and insert the BIOS/EC/KBC rewriting disk into either the external FDD. 5. Turn on the power while holding down the [`~] key. (Keep holding down the key until a message appears on the screen.) The EC/KBC rewriting starts. 6. When the EC/KBC rewrite is completed, the system is automatically turned off. Note: 1. Rewrite the EC/KBS only when instructed by a diagnostic disk release notice. 2. Connect the AC adapter to the computer when you rewrite the EC/KBC. 3. Do not turn off the power while you are rewriting the EC/KBC. If the rewrite fails, it might be impossible to start up the computer. 4. If you fail to rewrite EC/KBC, then when you next turn on the power, a message may be displayed that the contents of the EC/KBC have been erased. In this case, insert the BIOS/EC/KBC rewriting disk, and the EC/KBC will be rewritten. 5. Normally it takes about 30 seconds to rewrite the EC/KBC. It may take 3 minutes (maximum), depending on the conditions of the computer or ICs. The computer is not hung up. Allow sufficient time. Never reboot or turn off the power to the computer before the rewriting is completed.
G-1

Toshiba Qosmio f40 f45

Uploaded by

Copyright:

Available Formats

Toshiba Qosmio f40 f45

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Toshiba Qosmio f40 f45

Uploaded by

Copyright:

Available Formats

Toshiba Personal Computer Qosmio F40/F45

(PQF43x) (PQF44x) (PQF46x) (PQF47x)

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

Chapter 1 Hardware Overview

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

1 Hardware Overview Express Card Slot (BTO)

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

ID Parts Description Placement Part A

Qosmio F40/F45 Maintenance Manual

ID Parts Description Placement Part B

Qosmio F40/F45 Maintenance Manual

Figure 1-3 Computer Block Diagram

Qosmio F40/F45 Maintenance Manual

Figure 1-4 System Board Configurations

Qosmio F40/F45 Maintenance Manual

1.2 System Unit Components

System Unit Components

Qosmio F40/F45 Maintenance Manual

1.2 System Unit Components

Figure 1-5 System Unit Block Diagram

Qosmio F40/F45 Maintenance Manual

1.2 System Unit Components

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

1.2 System Unit Components

Qosmio F40/F45 Maintenance Manual

1.2 System Unit Components

Qosmio F40/F45 Maintenance Manual

1.2 System Unit Components

Qosmio F40/F45 Maintenance Manual

1.2 System Unit Components IEEE802.11agn: 2.4GHz / 5.4GHz

Qosmio F40/F45 Maintenance Manual

1.3 2.5-inch HDD

Figure 1-6 SATA HDD Table 1-1 HDD Specifications

Qosmio F40/F45 Maintenance Manual

DVD Super Multi (+-R Double Layer)) 1 Hardware Overview

DVD Super Multi (+-R Double Layer)

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

DVD Super Multi (+-R Double Layer)) 1 Hardware Overview

Table 1-3 HD DVD-ROM Drive Specifications

Qosmio F40/F45 Maintenance Manual

Table 1-4 HD DVD-R Drive Specifications

Qosmio F40/F45 Maintenance Manual

Qosmio F40/F45 Maintenance Manual

1.7 Power Supply

Qosmio F40/F45 Maintenance Manual

Batteries 1 Hardware Overview

Table 1-6 Quick/Normal Charging Time

Qosmio F40/F45 Maintenance Manual