Pure Bending PDF

Department of Chemical Engineering Strength of Materials for Chemical Engineers (0935381)
Chapter 4 Pure Bending

1) 2) 3) 4) 5) Center of gravity and neutral axis. Moment of inertia. Theory of simple bending. Bending of composite or flitched beam. Combined bending and direct stress.
1) Center of Gravity
Centroid of an area is the point about which the area could be balanced if it was supported from that point. a) Simple shapes
b) Area has an axis of symmetry
c) Two axis of symmetry do not occur
AT y = Ai y i y=
A y
i
AT
Where AT = total area o f the composite shape y = distance to the centroid of the composite shape measured form some reference axis OX. Ai = area of one component part the shape. yi = distance the centroid at the component part the reference axis. Or
AT x = Ai xi x=
Ax
i
AT Where x = distance to the centroid of the composite shape measured form some reference axis OY. xi = distance the centroid at the component part the reference axis.
2)
Moment of Inertia
Moment of inertia is a measure of the resistance of the section to applied moment or load that tends to bend it. Moment of inertia depends on the shape and not material. It is a derived property.
I XX = da. y 2 = y 2 .dA is called the moment of inertia or the second moment of area about the axis XX. I YY = da.x 2 = x 2 .dA is called the moment of inertia or the second moment of area
about the axis YY.
Parallel axis Theorem

This theorem is mainly used to transfer the moment of inertia of a body from its individual axis to another reference line. I OX = I XX + A. y 2
I OY = I YY + A.x 2
3)
Assumption for the Simple Bending Theory

1. 2. 3. 4. 5. 6.
The beam is initially straight and unstressed. The material is homogeneous, same density and elastic properties. The elastic limit is nowhere exceeded. Youngs modulus for the materials is the same in tension and compression. Plane crosssection remains plane before and after bending. No resulted force perpendicular to any cross section.
Bending theory
If we apply a constant B.M. If will bend to radius R. The top fibers of the beam will be subjected to tension. The bottom fibers of the beam will be subjected to compression. Somewhere between the two there are points at which the stress is zero. Locus of all points is termed the neutral axis. The radius of curvature R is then measured to this axis. The neutral axis will always pass through the centre of area of centroid. The maximum tension and compression will be at the outer surface or the farthest distance from the neutral axis.
Consider fiber AB distance y from the N.A. when the beam is bent this will stretch to AB. Extension AB AB Strain in AB = = Original Length AB AB = CD CD = C D
A B - CD CD C D = R AB = (R + y ) (R + y ) R = y Strain = R R Within the elastic region: Stress Strain = = Young' s Modulus E y = E R E = y R E = y R If the strip of area A E = y R E F = .A = . y.A R This force has a moment about the N.A of E F . y = . y 2 .A R The total moment for the whole cross section is: Strain =
F.y = R .y
M =
.A
E y 2 .A R 2 y .A is the second moment of area of the cross-section. M = E I R
M E = = I R y If the beam is of uniform section, the material of the beam is homogeneous and the applied moment is constant, I, E, M remain constant and hence the radius of curvature of the beam will also be constant. E R= I M EI is known as the flexural rigidity. For larger value of R smaller deflection greater the rigidity. M Maximum Stress max = y max I I I M = max = max y max y max
I y max
is termed the section modulus Z.
Z=
I y max I I and Z 2 = y1 y2
M = Z max for symmetrical beam

for unsymmetrical sections Z 1 =
4)
Bending of Composite or Flitched Beams

Composite beam is one which is constructed from a combination of material (flitched beam).
Force steel = ( .dy.t )steel = ( .dy.t )equivalent Since the moment at any section must be the same in the equivalent section as in the original, so that the force at given dy in the equivalent beam must be equal to that at the strip it replaces. .t = .t .E.t = .E .t Strain must be equal = E.t = E .t t E = t E E t = t E Thus to replace the steel strip by an equivalent wooden strip the thickness must be E multiplied by the modular ratio . E E t = = E t E = E Where: = the stress in the steel section. = the stress in the equivalent section. t = the thickness of the steel section. t = the thickness of the equivalent
5)
Combined Bending and Direct Stress Eccentric Loading

a) Eccentric loading on one axis
=
P M y m A I xx
M = P.e P P.e = m y A I xx The equation of the N.A can be obtained by setting equal to zero.
0=
P P.e y m A I xx
P P.e y = A I xx
yN = m
I xx A.e
The larger the eccentricity of the load the closer the N.A. will be to the axis of symmetry. yN is the distance between the N.A. and the axis of symmetry.
b) Eccentric loading on two axis

If the applied load will not be applied on either of the axis of symmetry, there will be a direct stress effect plus simultaneous bending about both axis. The total stress at any point (x, y): P.k P P.h = m y xm I xx A I yy Equation of the N.A. is obtained by equating to zero: P P.h P.k xm y 0= m A I yy I xx A.h A.k x y I yy I xx This is linear equation in x and y. The line may or may not cut the section. 1=
(MiddleQuarter) and (MiddleThird) Rules

For rectangular and circular cross sections, provided that the load is applied within certain defined areas, no tension will be produced whatever the magnitude of the applied compressive load.

Pure Bending PDF

Uploaded by

Copyright:

Available Formats

Pure Bending PDF

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pure Bending PDF

Uploaded by

Copyright:

Available Formats

Department of Chemical Engineering Strength of Materials for Chemical Engineers (0935381)

Chapter 4 Pure Bending

b) Area has an axis of symmetry

c) Two axis of symmetry do not occur

about the axis YY.

Parallel axis Theorem

Assumption for the Simple Bending Theory

E y 2 .A R 2 y .A is the second moment of area of the cross-section. M = E I R

is termed the section modulus Z.

M = Z max for symmetrical beam

Bending of Composite or Flitched Beams

Combined Bending and Direct Stress Eccentric Loading

b) Eccentric loading on two axis

(MiddleQuarter) and (MiddleThird) Rules

You might also like