Stan's 3.30 Series Front & Rear Hub: Tech Manual
Stan's 3.30 Series Front & Rear Hub: Tech Manual
Stan's 3.30 Series Front & Rear Hub: Tech Manual
2013
MAINTENANCE
NoTubes.com
202 Daniel Zenker Dr Big Flats, NY 14814 (607) 562-2877 sales@notubes.com
Lubrication:
The cartridge sealed bearings that are standard in Stans hubs can be cleaned and greased by removing the seal with a razor blade, but full bearing replacement is recommended and usually necessary when wear is determined. Use a small amount of lightweight grease on the pawl and drive ring mechanism in the free hub. An extra amount of lightweight grease may be added to the free hub if quieter operation is desired. For extreme cold conditions (below 30F) mix free hub grease with a few drops of 10w synthetic oil or remove the grease and use synthetic oil alone such as Dumonde Tech Freehub Grease or Morningstar Free Hub Soup TM. Riding in wet conditions will require more frequent service. High-pressure spray washing, transporting or riding the bicycle in the rain, or submersion in water while riding can all lead to lubricant contamination by water. When these situations occur, more frequent hub service is necessary.
1
Revised September 18, 2012
Freehub Specications:
Stans 3.30, 3.30Ti, 3.30R, and 3.30HD rear cassette hubs are designed to be compatible with Shimano and SRAM 8/9/10 speed cassettes. A 3.30R Campagnolo freehub is available for 10/11 speed Campagnolo cassettes. 3.30R Campagnolo hubs do not come with a cassette lock ring. NOTE: We recommend using cassettes with a rigid alloy carrier (XTR, XT, XO, etc. - Figure 1) for the largest sprockets. Cassettes with individual steel sprockets (Figure 2) may mark the alloy freehub, though marks are only cosmetic and will not affect the performance of the hub.
Warranty Policy:
All NoTubes products are covered under a 1 year warranty against manufacturing defects. Warranty does not cover abuse, misuse, consequential damages, normal wear and tear, and improper installation. Warranties only apply to the original owner. If a product is found defective customer will receive, at the discretion of Stans Notubes, free repair or replacement.
2
Revised September 18, 2012
Table of Contents
I. Disassembly of Stans Type II 3.30, 3.30Ti, 3.30SS Rear Hubs: . . . . . . . . . . . . . . . . . . . . . . . 4 II. Reassembly of Stans Type II 3.30, 3.30Ti, 3.30SS Rear Hubs: . . . . . . . . . . . . . . . . . . . . . . . 5 III. Disassembly of Stans 3.30, 3.30Ti, 3.30R, 3.30SS Rear Hubs: . . . . . . . . . . . . . . . . . . . . . . . 6 IV. Reassembly of Stans 3.30, 3.30Ti, 3.30R, 3.30SS Rear Hubs: . . . . . . . . . . . . . . . . . . . . . . . . 7 V. Disassembly of Stans 3.30 HD Series Rear Hubs: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 VI. Reassembly of Stans 3.30 HD Series Rear Hubs: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 VII. Disassembly and Assembly of Stans 3.30, 3.30R, 3.30Ti, 3.30HD, 3.30SS Freehub: . . . . . . . 9 VIII. Assembly of Stans 3.30, 3.30R, 3.30Ti, 3.30HD, 3.30SS Freehub: . . . . . . . . . . . . . . . . . . . . 10 IX. Disassembly of Stans 3.30, 3.30Ti Front Disc Hubs: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 X. Disassembly of Stans 3.30HD Series Front Disc Hubs: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 XI. Reassembly of Stans 3.30, 3.30Ti, 3.30HD Front Disc Hubs: . . . . . . . . . . . . . . . . . . . . . . . . 12 XII. Disassembly of Stans 3.30R Front Road Hub: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 XIII. Reassembly of Stans 3.30R Front Hub: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 XIV. Chain Line for 3.30SS Rear Hubs: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3
Revised September 18, 2012
Maintenance
I. Disassembly of Stans Type II 3.30, 3.30Ti, 3.30SS Rear Hubs:
Note: The Type II hub can be identied by the stainless steel inserts on the end of each end cap where the hub mounts into the frame. TOOLS NEEDED: one-5mm hex/Allen wrench, one-cone wrench (any size), plastic mallet, bearing press if available. Note: all threaded fasteners are standard right hand. 1. Remove the non-drive side end cap with pliers or an axle vise. 2. Insert the edge of the cone wrench into the slot of the axle on the non-drive side and hold secure while using a 5mm hex to remove the second end cap Figure 1 Type II. 3. Remove the free hub body. 4. Lightly tap one end of the axle to remove one bearing - See Figure 2 of section III. 5. Insert the axle back into the hub and tap out the other bearing - See Figure 3 of section III. 6. Replace worn bearings if necessary (bearing #6802) 7. Clean and grease free hub pawls.
4
Revised September 18, 2012
5
Revised September 18, 2012
6
Revised September 18, 2012
7
Revised September 18, 2012
8
Revised September 18, 2012
VII. Disassembly and Assembly of Stans 3.30, 3.30R, 3.30Ti, 3.30HD, 3.30SS Freehub:
TOOLS NEEDED: plastic mallet, 14mm or 15mm socket, 20mm socket, retaining ring pliers, bearing press if available. Note: all threaded fasteners are standard right hand. 1. Remove the bearing retaining ring from the end of the outside bearing Figure 10. 2. Place the freehub right-side down on a wooden table or board and use a 14mm or 15mm socket and plastic mallet to tap out the two #6902 bearings and bearing spacers Figure 11. 3. Clean parts and replace worn bearings if necessary (bearing #6902).
9
Revised September 18, 2012
10
Revised September 18, 2012
11
Revised September 18, 2012
12
Revised September 18, 2012
13
Revised September 18, 2012
14
Revised September 18, 2012