BCS Two-Wheel Tractor & Power Harrow Operating Instructions PDF

MAINTENANCE GUIDE
For engine maintenance please refer to engine manufacturers manual. After every hour of operation stop the engine and remove the spark plug cap. Check engine oil level (recommended oil SAE 10w/40). Remove all foreign matter from the digging knives assembly e.g. wire, string, grass etc. Do not turn the machine on its side for cleaning. When the machine is not in use always leave the clutch lever pulled in and secured with locking clip. Replace the spark plug cap.
OPERATING INSTRUCTIONS & SAFETY NOTES
Fig. 1
BCS
Fig. 2
Throttle lever Clutch lever Fwd/rev lever Diff lock lever Digging knives lever Wheel speed lever Handlebar adjuster Red stop lever
BCS TWO-WHEEL TRACTORS 730 740

with POWER HARROW
Depth adjuster
Gearbox oil level Petrol cap Choke lever Engine oil level Fuel tap Recoil starter
VIBRATION & SOUND LEVELS Machine RPM 3000
IMPORTANT
READ CAREFULLY
Vibration Sound Level m/sec2 3 Axis dB(A)

4.3 7.3 4.4 7.3 85.0 97.0 88.0 97.0
BCS730P + 24 Power Harrow
BCS730D + 24 Power Harrow 3000 BCS740P + 24 Power Harrow

3000
BCS740D + 24 Power Harrow 3600
WEAR EAR PROTECTION

Tracmaster Ltd, Teknol House, Victoria Road, Burgess Hill RH15 9LH Tel: 01444 247689 Fax: 01444 871612 Website: www.tracmaster.co.uk E-mail: info@tracmaster.co.uk
Tracmaster Ltd 2008. Specifications are subject to change without prior notice. OP/TWT+GLM/0308
WEAR EYE PROTECTION
WEAR SAFETY FOOTWEAR
No liability will be accepted for any damage caused to persons or property through failure to observe the operating and safety instructions.
SAFETY
ALWAYS start the engine in the open air DO NOT smoke when refuelling DO NOT mix OIL with the fuel ALWAYS stop the engine before making any adjustments, refuelling, moving or cleaning, or when the unit is unattended USE ONLY unleaded petrol from fuel containers designed for this purpose - refuel outdoors only and replace the tank cap securely IN CASE of petrol spillage move the machines away from the area of spillage and allow the petrol vapours to dissipate before starting the engine DO NOT remove any safety guards that are fitted DO NOT touch any moving parts or attempt any maintenance whilst the machine is running - KEEP HANDS AND FEET AWAY BEFORE starting work clear the work area of any objects that could damage the machine DO NOT allow children or anyone uninstructed to operate the machine - KEEP ANIMALS AWAY DO NOT use on slopes or banks ALWAYS wear suitable clothing to give personal protection including footwear that offers a good grip AVOID wearing loose garments that may catch in moving parts KNOW how to stop the machine in an emergency NEVER select reverse gear with your back to a wall or other immovable object NEVER interfere with any control settings on the engine IF A FAULT develops DO NOT attempt any repair - immediately contact the supplier from whom the machine was obtained VISUALLY INSPECT the machine before use - ensure all tines, nuts and bolts are tight and not worn or damaged and replace tines if necessary KEEP IN MIND the operator is responsible for accidents or hazards occurring to people or property WEAR ear protection and protective footwear
TO START DIESEL ENGINE

Check fuel level. Only use diesel from a clean container. Never refuel when the engine is hot or running. Depress the engine stop lever (the red lever on the handlebar) then pull in the clutch lever and secure with locking clip. Ensure the wheel speed lever is in neutral O position. Apply half throttle (the lever on the right handlebar). Press and hold the decompression lever on top of the engine. Pull recoil start handle gently until it engages then slowly pull the engine over 2-3 times to prime the engine. Release the decompression lever and gently pull over the engine until compression is felt. Press, but do not hold, the decompression lever and give the starter handle a good strong pull to start the engine. Once the engine has started return the throttle to idle position.
OPERATION
Use handlebar adjuster to set handlebar height. Pull up clutch lever (located on left-hand handlebar). automatically release stop lever locking clip. Ensure forward/reverse lever is in forward position. Select working speed one. NEVER select a higher wheel speed for work. Engage drive to the digging knives by pushing the lever forward. Release clutch lever slowly and fully, keeping the red engine stop lever depressed as engine will stop if released. Commence work. This will
TO STOP ENGINE
Close the throttle. Engage clutch lever. Locate gear lever in neutral position. Disengage drive to the digging knives. Release clutch lever. Release engine stop lever completely. WARNING: THE EXHAUST COVER MAY BE HOT - DO NOT TOUCH
TO START PETROL ENGINE

Using the dipstick provided, check the engine oil level. Top up with 10w/40 oil if necessary (if the dipstick is clear of oil). Check fuel level. Only use unleaded petrol from a clean container. Never re-fuel when the engine is hot or running. Leave 1 air space in the fuel tank. Depress the engine stop lever (the red lever on the left handlebar) then pull up the clutch lever and secure with locking clip. Ensure the wheel speed lever is in neutral O position. Apply half throttle (the lever on the right handlebar). Turn the fuel tap to on position, if the engine is cold set the choke lever to on position. Pull the recoil start handle gently until it engages then give it a good strong pull to start the engine. When the engine has started, release the choke lever after a few seconds and return the throttle lever to idle position.
OPERATING HINTS
The working depth is adjusted by moving pin A and raising or lowering the roller. The levelling is done by the front scraper blade B. If the ground is hard and undulating the scraper blade must be fully raised by adjusting screws C and several passes made with the machine until the earth is loosened enough so the blade can be lowered to commence levelling. THE SCRAPER BLADE MUST NOT BE ALLOWED TO CONTACT GROUND THAT HAS NOT BEEN LOOSENED AS DAMAGE TO THE BLADE MAY RESULT. If the speed or digging knives lever does not engage immediately, release clutch lever slightly and 'feel in' with the engine on tick-over. DO NOT RIDE THE CLUTCH. If one wheel begins to lose traction engage the differential lock by pulling the black lever on top of the right hand handlebar towards you to engage drive to both wheels. Always pull in the clutch lever before engaging any gear, digging unit or changing forward/reverse. The clutch lever must be fully released when working. Do not operate the machine with the clutch lever partially engaged as serious damage may occur. DO NOT WORK ON SLOPES

BCS Two-Wheel Tractor & Power Harrow Operating Instructions PDF

Uploaded by

Copyright:

Available Formats

BCS Two-Wheel Tractor & Power Harrow Operating Instructions PDF

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BCS Two-Wheel Tractor & Power Harrow Operating Instructions PDF

Uploaded by

Copyright:

Available Formats

MAINTENANCE GUIDE

OPERATING INSTRUCTIONS & SAFETY NOTES

BCS TWO-WHEEL TRACTORS 730 740

VIBRATION & SOUND LEVELS Machine RPM 3000

Vibration Sound Level m/sec2 3 Axis dB(A)

BCS730P + 24 Power Harrow

BCS730D + 24 Power Harrow 3000 BCS740P + 24 Power Harrow

BCS740D + 24 Power Harrow 3600

WEAR EAR PROTECTION

WEAR EYE PROTECTION

WEAR SAFETY FOOTWEAR

TO START DIESEL ENGINE

TO START PETROL ENGINE

You might also like