DANIEL SENIOR ORIFICE FITTINGS

__________________________________________
2" - 8" 150-1500 2" - 6" 2500 10" - 14" 150-1500 PARTS LIST AND MATERIALS, INSTRUCTIONS FOR INSTALLATION, OPERATION AND MAINTENANCE

DANIEL MEASUREMENT AND CONTROL, INC. AN EMERSON PROCESS MANAGEMENT COMPANY HOUSTON, TEXAS

Part Number 3-9008-001 Revision D

SEPTEMBER 2006

IMPORTANT INSTRUCTIONS Daniel Measurement and Control, Inc. (Daniel) designs, manufactures and tests this flow product to be operated within specific flow conditions. Because these instruments are sophisticated technical products, you must install, use and maintain them to ensure that they operate within the range specified on the equipment nameplate. The following instructions must be adhered to and integrated into your safety program when installing, using and maintaining Daniel Products, including Daniel Senior Orifice Fittings.

SERIOUS PERSONAL INJURY OR DEATH Read nameplate to determine maximum allowable operating pressure (MAOP) before placing product in service. Operating this product above MAOP may lead to serious injury or death. Read all instructions prior to installing, operating and servicing the product. If this instruction manual is not the correct manual, telephone 1-713-827-6314 and the requested manual will be provided. Save this instruction manual for future reference. If you do not understand any of the instructions, contact your Daniel representative for clarification. Follow all warnings, cautions and instructions marked on and supplied with the product. Inform and educate your personnel in the proper installation, operation and maintenance of the product. Install your equipment as specified in the installation instructions of the appropriate instruction manual and per applicable local and national codes. Connect all products to the proper electrical and pressure sources. To ensure proper performance, use qualified personnel to install, operate, update, program and maintain the product. When replacement parts are required, ensure that qualified people use replacement parts specified by the manufacturer. Unauthorized parts and procedures can affect the Product's performance and place the safe operation of your process at risk. Look-alike substitutions may result in fire, hazards or improper operation.

Ensure that all equipment doors are closed and protective covers are in place, except when maintenance is being performed by qualified persons, to prevent personal injury. ALWAYS READ AND FOLLOW THE DANIEL SENIOR ORIFICE FITTING OWNERS MANUAL AND ALL PRODUCT WARNINGS AND INSTRUCTIONS.

DANIEL SENIOR ORIFICE FITTING DANIEL SENIOR ORIFICE FITTINGS 2" - 8" 150-1500 2" - 6" 2500 10" - 14" 150-1500

S E P 2006

NOTICE
DANIEL MEASUREMENT AND CONTROL, INC. ("DANIEL") SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS IN THIS MANUAL O R OMISSIONS FROM THIS MANUAL. DANIEL M AKES NO W ARRANTIES, EXPRESSED OR IM PLIED, INCLUDING THE IM PLIED WARRANTIES OF M ERCHANTABILITY AND FITNESS FO R A PARTICULAR PURPOSE W ITH RESPECT TO THIS M ANUAL AND, IN NO EVENT, SHALL DANIEL BE LIABLE FO R A NY INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAM AGES INCLUDING, BUT NOT LIM ITED TO, LOSS OF PRODUCTION, LOSS OF PROFITS, LOSS OF REVENUE OR USE AND COSTS INCURRED INCLUDING W ITHOUT LIM ITATION FOR CAPITAL, FUEL AND POW ER, AND CLAIM S OF THIRD PARTIES. PRODUCT NAM ES USED HEREIN ARE FOR M ANUFACTURER OR SUPPLIER IDENTIFICATION ONLY AND M AY BE TRADEM ARKS/REGISTERED TRADEM ARKS OF THESE COM PANIES. THE CONTENTS OF THIS PUBLICATION ARE PRESENTED FOR INFORMATIONAL PURPOSES ONLY, AND W HILE EVERY EFFORT HAS BEEN MADE TO ENSURE THEIR ACCURACY, THEY ARE NOT TO BE CONSTRUED AS W ARRANTIES OR GUARANTEES, EXPRESSED OR IMPLIED, REGARDING THE PRODUCTS OR SERVICES DESCRIBED H EREIN OR THEIR USE OR APPLICABILITY. ALL SALES ARE GOVERNED BY DANIELS TERMS AND CONDITIONS, W HICH ARE AVAILABLE UPON REQUEST. W E RESERVE THE RIGHT TO MODIFY OR IMPROVE THE DESIGNS OR SPECIFICATIONS OF SUCH PRODUCTS AT ANY TIME. DANIEL DOES NOT ASSUME RESPONSIBILITY FOR THE SELECTION, USE OR MAINTENANCE OF ANY PRODUCT. RESPONSIBILITY FOR PROPER SELECTION, USE AN D M AINTENANCE OF ANY DANIEL PRODUCT REMAINS SOLELY W ITH THE PURCHASER AND END-USER. DANIEL AND THE DANIEL LOGO ARE REGISTERED TRADEMARKS OF DANIEL INDUSTRIES, INC. THE EMERSON LOGO IS A TRADEMARK AND SERVICE MARK OF EMERSON ELECTRIC CO.

COPYRIGHT 2006 BY DANIEL MEASUREMENT AND CONTROL, INC. HOUSTON, TEXAS, U.S.A. All rights reserved. No part of this work may be reproduced or copied in any form or by any means - graphic, electronic or mechanical - without first receiving the written permission of Daniel Measurement and Control, Inc., Houston, Texas, U.S.A.

PREFACE

S E P 2006

DANIEL SENIOR ORIFICE FITTING

WARRANTY
1. LIM ITED W ARRANTY: Subject to the limitations contained in Section 2 herein and except as otherwise expressly provided herein, Daniel Measurement and Control, Inc. ("Daniel") warrants that the firmware will execute the programming instructions provided by Daniel, and that the Goods manufactured or Services provided by Daniel will be free from defects in materials or workmanship under normal use and care until the expiration of the applicable warranty period. Goods are warranted for twelve (12) months from the date of initial installation or eighteen (18) months from the date of shipment by Daniel, whichever period expires first. Consumables and Services are warranted for a period of 90 days from the date of shipment or completion of the Services. Products purchased by Daniel from a third party for resale to Buyer ("Resale Products") shall carry only the warranty extended by the original manufacturer. Buyer agrees that Daniel has no liability for Resale Products beyond making a reasonable commercial effort to arrange for procurement and shipping of the Resale Products. If Buyer discovers any warranty defects and notifies Daniel thereof in writing during the applicable warranty period, Daniel shall, at its option, promptly correct any errors that are found by Daniel in the firmware or Services, or repair or replace F.O.B. point of manufacture that portion of the Goods or firmware found by Daniel to be defective, or refund the purchase price of the defective portion of the Goods/Services. All replacements or repairs necessitated by inadequate maintenance, normal wear and usage, unsuitable power sources, unsuitable environmental conditions, accident, misuse, improper installation, modification, repair, storage or handling, or any other cause not the fault of Daniel are not covered by this limited warranty, and shall be at Buyer's expense. Daniel shall not be obligated to pay any costs or charges incurred by Buyer or any other party except as may be agreed upon in writing in advance by an authorized Daniel representative. All costs of dismantling, reinstallation and freight and the time and expenses of Daniel's personnel for site travel and diagnosis under this warranty clause shall be borne by Buyer unless accepted in writing by Daniel. Goods repaired and parts replaced during the warranty period shall be in warranty for the remainder of the original warranty period or ninety (90) days, whichever is longer. This limited warranty is the only warranty made by Daniel and can be amended only in a writing signed by an authorized representative of Daniel. Except as otherwise expressly provided in the Agreement, THERE ARE NO REPRESENTATIONS OR W ARRANTIES OF ANY KIND, EXPRESSED OR IMPLIED, AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE,

Buyer acknowledges and agrees that corrosion or erosion of materials is not covered by this warranty.
OR ANY OTHER MATTER W ITH RESPECT TO ANY OF THE GOODS OR SERVICES. 2. LIM ITATION OF REM EDY AND LIABILITY: DANIEL SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN PERFORMANCE. THE SOLE AND EXCLUSIVE REM EDY FOR BREACH OF W ARRANTY HEREUNDER SHALL BE LIMITED TO REPAIR, CORRECTION, REPLACEMENT OR REFUND OF PURCHASE PRICE UNDER THE LIMITED W ARRANTY CLAUSE IN SECTION 1 HEREIN. IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (W HETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OTHER T ORT OR OTHERW ISE), SHALL DANIEL'S LIABILIT Y TO BUYER AND/OR ITS CUSTOMERS EXCEED THE PRICE TO BUYER OF THE SPECIFIC GOODS MANUFACTURED OR SERVICES PROVIDED BY DANIEL GIVING RISE TO THE CLAIM OR CAUSE OF ACTION. BUYER AGREES THAT IN NO EVENT SHALL DANIEL'S LIABILITY TO BUYER AND/OR ITS CUSTOMERS EXTEND TO INCLUDE INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES. THE TERM "CONSEQUENTIAL DAMAGES" SHALL INCLUDE, BUT NOT BE LIMITED TO, LOSS OF ANTICIPATED PROFITS, REVENUE OR USE, AND COSTS INCURRED INCLUDING W ITHOUT LIMITATION FOR CAPITAL, FUEL AND POW ER, AND CLAIM S OF BUYERS CUSTOMERS.

ii

PREFACE

DANIEL SENIOR ORIFICE FITTING

S E P 2006

TABLE OF CONTENTS 1.0 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 through 1-17

2.0

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 Preliminary Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Daniel Senior Orifice Fitting Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 Line Pressure Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 Orifice Plate Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-1 2-1 2-3 2-5 2-7

3.0

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3. 1 Normal Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 Plate Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 Plate Insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SUPPLEMENTAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 Recommended Spare Parts for One Year Operation . . . . . . . . . . . . . . . . . . . . . 5.2 Lubricant Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3 Screw and Stud Torque Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 4-2 4-4 4-5 5-1 5-1 5-2 5-2

4.0

5.0

TABLE OF CONTENTS

iii

S E P 2006

DANIEL SENIOR ORIFICE FITTING

This page intentionally left blank.

iv

TABLE OF CONTENTS

DANIEL SENIOR ORIFICE FITTING

S E P 2006

1.0 1.1

INTRODUCTION General

This manual is designed to assist in the installation, operation and maintenance of Daniel Senior Orifice Fittings. To assure proper installation and startup it is important to read this manual in its entirety. 1.2 Description

The Daniel Senior Orifice Fitting is an orifice plate holding device used in a flow measurement system. The Daniel Senior Orifice Fitting is designed to: 1) position an orifice plate, concentric to flow moving through a line, according to API 14.3.2 installation requirements. 2) allow the user to remove and replace an orifice plate from the system with little, or no, interruption in service. An orifice plate properly positioned within a Daniel Senior Orifice Fitting creates a static pressure difference between the upstream side of the orifice plate and the downstream side of the orifice plate. The flow rate through the Daniel Senior Orifice Fitting is determined from the measured value of the difference in upstream and downstream pressure, from information concerning the flowing fluid, and from the conditions under which the element is in use. The Daniel Senior Orifice Fitting utilizes a dual chamber design. One chamber, the measurement or body chamber, properly positions the orifice plate in the flow stream. The second chamber, or top chamber, is a temporary holding vessel for the orifice plate in removing or installing operations. The two chambers are separated by a slide valve. Using a Daniel Senior Orifice Fitting in a flow measurement system may eliminate the need for bypass piping, valves, and other fittings necessary with conventional orifice fitting installations. Maintenance technicians can replace and repair all parts of the Daniel Senior Orifice Fitting, including the slide valve assembly, without removing the body from the line. Daniel designs their Daniel Senior Orifice Fittings to meet or exceed the latest AGA recommendations and in accordance to all applicable standards, including ISO 5167. Products bearing the CE mark are designed and manufactured in compliance with the European Union Pressure Equipment Directive (PED) 97/23/EC.

INTRODUCTION

1-1

S E P 2006

DANIEL SENIOR ORIFICE FITTING

1.3

Specifications

1-2

INTRODUCTION

DANIEL SENIOR ORIFICE FITTING

S E P 2006

All Parts on Daniel Senior Orifice Fittings may be replaced or repaired without removing the Daniel Senior Orifice Fitting body from the line.
PARTS AND M ATERIALS Part No. *1 * 1G * 1H * 1D * 1K * 1J *2 3 4 5 * 5A * 5B 6 7 * 8A 8DMC 8E-DSC 8TSC Description Equalizer Valve (Complete): Stem Packing Nut Ball Packing W asher Packing Ring Operating W rench Slide Valve Strip Body Slide Valve Gear Shaft Slide Valve Indicator Plate Slide Valve Indicator Pointer Lower Plate Carrier Gear Shaft Upper Plate Carrier Gear Shaft Plate Carrier Spring Pin Plate Carrier Orifice Plate Sealing Unit 150-600 Orifice Plate Sealing Unit 150-900 Alternate Seals Available See Catalog - #500 Sealing Bar Sealing Bar Gasket
(1)

M aterial 316 Stainless Steel CS (CP) 18-8 Stainless Steel 17-4PH Stainless Steel Teflon Ductile Iron Type 410 Stainless Steel Cast Carbon Steel CS (CP) Cast Aluminum Stainless Steel CS (CP) CS (CP) 18-8 SS 316 SS Nitrile (Removable) Teflon (Removable)

NUM BER REQUIRED SIZE 2" 3" 4" 6" 8" 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1

9 9A * * * * * 10B 10C 10D 10E 10G

CS (CP) Composite CS (CP) 316 Stainless Steel Synthetic Rubber Alloy Steel Alloy Steel (CP) CS (CP) Type 304 or 316 Stainless Steel Cast Carbon Steel 316 Stainless Steel 150-600 900

1 1 1 1 1 1 4 4 1 1 1 4

1 1 1 1 1 1 4 4 1 1 1 4

1 1 1 1 1 1 5 5 1 1 1 4

1 1 1 1 1 1 6 6 1 1 1 6

1 1 1 1 1 1 7 8 1 1 1 6

Bleeder Valve (Complete): Body Needle "O" Ring Set Screw Clamping Bar Screw Clamping Bar Orifice Plate Top Slide Valve Springs

* 11 12 13 14 * 15

INTRODUCTION

1-3

S E P 2006

DANIEL SENIOR ORIFICE FITTING

PARTS AND M ATERIALS Part No. * 16 17 * 17A 18 18A * 18B * 22A * 23 * 24 * 25 * 25A * 25B * 26 * 30 (2) * 31 (2) Description Slide Valve Carrier Guide Slide Valve Carrier Slide Valve Carrier Stop Pin Slide Valve Seat Slide Valve Seat /Top Gasket Slide Valve Seat Screw Bearing Plug and Stuffing Box Gasket Grease Gun (Complete) Grease Seal Double Ball Check Valve Packing Nut Packing Rings Centering Ring Stuffing Box Gland Drain Valve Plug "" N.P.T. Plug for Pressure Meter Tap Hex Nut Stud Bearing Plug Body (Upper) Bearing Plug Body (Lower) Stuffing Box Body (Upper) Stuffing Box Body (Lower) Bearing Plug Sleeve(Upper) Bearing Plug Sleeve (Lower) Stuffing Box Sleeve (Upper) Stuffing Box Sleeve (Lower) Plate Carrier Stop Pin Plate Carrier Stop Pin Lock Screw Plate Carrier Stop Pin Access Plug M aterial 316 Stainless Steel Cast Carbon Steel Cast Alloy Iron Carbon Steel (CP) Cast Alloy Iron Cast Iron Composite Alloy Steel Phosphate Treat Stainless Steel CS (CP) 316 Stainless Steel with Chrome-Steel Balls CS (CP) Teflon Teflon 316 SS CS (CP) CS (Chemically Treated) 150-600 900 150-600 900

NUM BER REQUIRED SIZE 2" 3" 4" 6" 8" 2 1 2 1 1 8 6 1 1 3 9 9 3 1 2 14 14 14 14 1 2 1 2 1 2 1 2 1 1 1 2 1 2 1 1 10 6 1 1 3 9 9 3 1 2 15 15 15 15 1 2 1 2 1 2 1 2 1 1 1 2 1 2 1 1 11 6 1 1 3 9 9 3 1 2 15 15 15 15 1 2 1 2 1 2 1 2 1 1 1 2 1 1 2 1 1 1 14 6 1 1 3 9 9 3 1 2 18 18 18 18 1 2 1 2 1 2 1 2 1 1 1 1 16 6 1 1 3 9 9 3 1 2 19 20 19 20 1 2 1 2 1 2 1 2 1 1 1 2 2

32 33 * 34 * 35 * 36 * 37 38 39 40 41 * 42 * 43 * 44

CS Alloy Steel CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP)

1-4

INTRODUCTION

DANIEL SENIOR ORIFICE FITTING

S E P 2006

Notes: 1. W hen venting upper chamber through bleeder valve (#10B), direct fluid and/or gas to a safe area using the threaded connection at the valve discharge port. 2. All Daniel Senior O rifice Fittings are supplied with pipe plugs on one side only. If additional quantities are required, please contact the factory direct. * Indicates Interchangeable Parts for all line sizes of specified pressure rating(s). General Notes: Most parts available in other materials upon specification. CS (Carbon Steel), CP (Cadmium Plated). The materials listed above indicate standard A trim. Various part materials are changed for NACE & "AASG" trim fittings. Shaded part numbers are for items which are fluid media PIC (parts in contact). W HEN ORDERING PARTS, PLEASE SPECIFY: (1) catalog number, (2) size, (3) serial number and date of the original purchase, (4) part number, (5) material, (6) quantity of parts required.

INTRODUCTION

1-5

S E P 2006

DANIEL SENIOR ORIFICE FITTING

1-6

INTRODUCTION

DANIEL SENIOR ORIFICE FITTING

S E P 2006

All Parts on Daniel Senior Orifice Fittings may be replaced or repaired without removing the Daniel Senior Orifice Fitting body from the line.
PARTS AND M ATERIALS Part No. *1 * 1G * 1H * 1D * 1K * 1J *2 3 4 5 * 5A * 5B 6 7 * 8A 8DMC 8TSC Description Equalizer Valve (Complete): Stem Packing Nut Ball Packing W asher Packing Ring Operating W rench Slide Valve Strip Body Slide Valve Gear Shaft Slide Valve Indicator Plate Slide Valve Indicator Pointer Lower Plate Carrier Gear Shaft Upper Plate Carrier Gear Shaft Plate Carrier Spring Pin Plate Carrier Orifice Plate Sealing Unit Alternate Seals Available See Catalog - #500 Sealing Bar Compoflex Sealing Bar Gasket Bleeder Valve (Complete): Body Needle "O" Ring Set Screw Clamping Bar Screw Clamping Bar Orifice Plate Top Body-Top Gasket (O Ring) Body-Top Gasket (Male-Female Joint) Not Illustrated Slide Valve Springs Slide Valve Carrier Guide M aterial 316 Stainless Steel CS (CP) 18-8 Stainless Steel 17-4PH Stainless Steel Teflon Ductile Iron Type 410 Stainless Steel Cast Carbon Steel CS (CP) Cast Aluminum Stainless Steel CS (CP) CS (CP) 18-8 SS 1500 316 SS 2500 CS (CP) 2500 Teflon (Removable) NUM BER REQUIRED SIZE 2" 3" 4" 6" 8" 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1

9HP 9CF * 10B (1) * 10C * 10D * 10E * 10G * 11 12HP 13 14 14CF 14CF-C * 15 * 16

CS (CP) Synthetic Composition CS (CP) 316 Stainless Steel Synthetic Rubber Alloy Steel Alloy Steel (CP) 1500 2500

1 1 1 1 1 1 10 10 1 1 1 1 1 4 2

1 1 1 1 1 1 10 10 1 1 1 1 1 4 2

1 1 1 1 1 1 12 12 1 1 1 1 1 4 2

1 1 1 1 1 1 14 14 1 1 1 1 1 6 2

1 1 1 1 1 1 16 1 1 1 1

CS (CP) Type 304 or 316 Stainless Steel Cast Carbon Steel Special 1500 Compound Parker Seal w/ 2500 Synthetic Rubber 316 Stainless Steel 316 Stainless Steel

6 2

INTRODUCTION

1-7

S E P 2006

DANIEL SENIOR ORIFICE FITTING

PARTS AND M ATERIALS Part No. 17 * 17A 18 18A Description Slide Valve Carrier Slide Valve Carrier Stop Pin Slide Valve Seat Slide Valve Seat Gasket M aterial Cast Carbon Steel Cast alloy Iron Carbon Steel (CP) 13% Chrome Stainless Steel Composite 1500 2500 Alloy Steel Phosphate Treat CS (CP) CS (CP) CS (CP) CS (CP) Stainless Steel Stainless Steel Synthetic Rubber 1500 2500 2500 2500 2500 2500 1500 2500 2500

* 18B 19HP 20HP 21HP 22HP * 22A *22A-HP * 22B * 23 * 24 * 25 * 25HP * 25A * 25A-HP * 25B * 25B * 25B-HP * 26 * 26B * 26E * 26C * 26D * 30 (2) * 31 (2) 32 33 * 34 * 35 * 36

Slide Valve Seat Screw Bearing Plug (Upper) Stuffing Box (Upper) Stuffing Box (Lower) Bearing Plug (Lower) Bearing Plug and Stuffing Box Gasket Bearing Plug and Stuffing Box Gasket Bearing Plug and Stuffing Box O Ring Grease Gun (Complete) Grease Seal Double Ball Check Valve Packing Nut Packing Nut Packing Rings Packing Rings Centering Ring Centering Ring - Bearing Plug Centering Ring - Stuffing Box Stuffing Box Gland External Stuffing Box Gland Internal Stuffing Box Gland Stuffing Box Gland O Ring Stuffing Box Gland O Ring Drain Valve Plug "" N.P.T. Plug for Pressure Meter Tap Hex Nut Stud Bearing Plug Body (Upper) Bearing Plug Body (Lower) Stuffing Box Body (Upper)

NUM BER REQUIRED SIZE 2" 3" 4" 6" 8" 1 1 1 1 1 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 Assembled metal-tometal 8 10 11 14 16 10 10 11 14 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 6 6 6 6 6 6 6 1 1 3 3 9 6 6 1 1 6 6 1 1 6 6 1 1 1 1 3 9 9

CS (CP) 316 Stainless Steel with Chrome-Steel Balls CS (CP) 1500 CS (CP) 2500 Teflon 1500 Teflon 2500 Teflon 1500 Teflon 2500 Teflon 2500 316 SS 1500 316 SS 2500 316 SS 2500 Synthetic Rubber 2500 Synthetic Rubber 2500 CS (CP) CS (Chemically Treated) CS Alloy Steel CS (CP) CS (CP) CS (CP) 1500 2500 1500 2500 1500 1500 1500

3 3 3 3 3 3 9 9 9 Varies with Fitting Size 9 9 9 9 9 9 9 9 6 6 6 6 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 6 6 6 6 1 1 1 1 2 2 2 2 14 16 14 16 1 2 1 14 16 14 16 1 2 1 16 16 16 16 1 2 1 18 18 18 18 1 2 1

1 2 18 18 1 2 1

1-8

INTRODUCTION

DANIEL SENIOR ORIFICE FITTING

S E P 2006

PARTS AND M ATERIALS Part No. * 37 38 39 40 41 * 42 * 43 * 44 Description Stuffing Box Body (Lower) Bearing Plug Sleeve(Upper) Bearing Plug Sleeve (Lower) Stuffing Box Sleeve (Upper) Stuffing Box Sleeve (Lower) Plate Carrier Stop Pin Plate Carrier Stop Pin Lock Screw Plate Carrier Stop Pin Access Plug CS CS CS CS CS CS CS CS (CP) (CP) (CP) (CP) (CP) (CP) (CP) (CP) M aterial 1500 1500 1500 1500 1500

NUM BER REQUIRED SIZE 2" 3" 4" 6" 8" 2 2 2 2 2 1 1 1 1 1 2 2 2 2 2 1 1 1 1 1 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Notes: 1. W hen venting upper chamber through bleeder valve (#10B), direct fluid and/or gas to a safe area using the threaded connection at the valve discharge port. 2. All Daniel Senior Orifice Fittings are supplied with pipe plugs on one side only. If additional quantities are required, please contact the factory direct. * Indicates Interchangeable Parts for all line sizes of specified pressure rating(s). General Notes: Most parts available in other materials upon specification. CS (Carbon Steel), CP (Cadmium Plated). The materials listed above indicate standard A trim. Various part materials are changed for NACE & "AASG" trim fittings. Shaded part numbers are for items which are fluid media PIC (parts in contact). W HEN ORDERING PARTS, PLEASE SPECIFY: (1) catalog number, (2) size, (3) serial number and date of the original purchase, (4) part number, (5) material, (6) quantity of parts required.

INTRODUCTION

1-9

S E P 2006

DANIEL SENIOR ORIFICE FITTING

1-10

INTRODUCTION

DANIEL SENIOR ORIFICE FITTING

S E P 2006

All Parts on Daniel Senior Orifice Fittings may be replaced or repaired without removing the Daniel Senior Orifice Fitting body from the line.
PARTS AND M ATERIALS Part No. *1 * 1G * 1H * 1D * 1K * 1J *2 3 4 5 * 5A * 5B 6 7 8DM 8E-DS 8E-DVS 8TS Description Equalizer Valve (Complete): Stem Packing Nut Ball Packing W asher Packing Ring Operating W rench Slide Valve Strip Body Slide Valve Gear Shaft Slide Valve Indicator Plate Slide Valve Indicator Pointer Lower Plate Carrier Gear Shaft Upper Plate Carrier Gear Shaft Plate Carrier Orifice Plate Sealing Unit 150-600 Orifice Plate Sealing Unit 150-600 Orifice Plate Sealing Unit 150-900 Alternate Seals Available See Catalog - #500 Sealing Bar Sealing Bar Gasket Bleeder Valve (Complete): Body Needle "O" Ring Set Screw Clamping Bar Screw Clamping Bar Orifice Plate Top Slide Valve Springs M aterial 316 Stainless Steel CS (CP) 18-8 Stainless Steel 17-4PH Stainless Steel Teflon Ductile Iron Type 410 Stainless Steel Cast Carbon Steel CS (CP) Cast Aluminum Stainless Steel CS (CP) CS (CP) CS (CP) Nitrile (Removable) Nitrile (Bonded to Both Faces of the Orifice Plate) Teflon (Removable) 1 NUM BER REQUIRED SIZE 10" 12" 14" 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1

9 9A * 10B (1) * 10C * 10D * 10E * 10G * 11 12 13 14 * 15

CS (CP) Composite CS (CP) 316 Stainless Steel Synthetic Rubber Alloy Steel Alloy Steel (CP) CS (CP) Type 304 or 316 Stainless Steel Cast Carbon Steel 316 Stainless Steel 150-600 900

1 1 1 1 1 1 8 8 1 1 1 6

1 1 1 1 1 1 10 10 1 1 1 7

1 1 1 1 1 1 11 22 1 1 1 8

INTRODUCTION

1-11

S E P 2006

DANIEL SENIOR ORIFICE FITTING

PARTS AND M ATERIALS Part No. * 16 17 * 17A Description Slide Valve Carrier Guide Slide Valve Carrier Slide Valve Carrier Stop Pin M aterial 316 Stainless Steel Cast Alloy Iron Carbon Steel (CP) Cast Alloy Iron TY 410 SS 17-4PH SS Composite Alloy Steel Phosphate Treat Stainless Steel CS (CP) 316 Stainless Steel with Chrome-Steel Balls CS (CP) Teflon Teflon 316 SS CS (CP) CS (Chemically Treated) CS Alloy Steel CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) 150-600

NUM BER REQUIRED SIZE 10" 12" 14" 2 1 2 1 2 1 2 1 2 1 2 1

18

Slide Valve Seat

900 900

1 1 1 18 6 1 1 3 9 9 3 1 2 22 22 1 2 1 2 1 2 1 2 1 20 6 1 1 3 9 9 3 1 2 22 22 1 2 1 2 1 2 1 2 1 1 24 6 1 1 3 9 9 3 1 2 24 24 1 2 1 2 1 2 1 2

18A * 18B * 22A * 23 * 24 * 25 * 25A * 25B * 26 * 30 * 31 32 33 * 34 * 35 * 36 * 37 38 39 40 41

(2) (2)

Slide Valve Seat /Top Gasket Slide Valve Seat Screw Bearing Plug and Stuffing Box Gasket Grease Gun (Complete) Grease Seal Double Ball Check Valve Packing Nut Packing Rings Centering Ring Stuffing Box Gland Drain Valve Plug "" N.P.T. Plug for Pressure Meter Tap Hex Nut Stud Bearing Plug Body (Upper) Bearing Plug Body (Lower) Stuffing Box Body (Upper) Stuffing Box Body (Lower) Bearing Plug Sleeve(Upper) Bearing Plug Sleeve (Lower) Stuffing Box Sleeve (Upper) Stuffing Box Sleeve (Lower)

1-12

INTRODUCTION

DANIEL SENIOR ORIFICE FITTING

S E P 2006

Notes: 1. W hen venting upper chamber through bleeder valve (#10B), direct fluid and/or gas to a safe area using the threaded connection at the valve discharge port. 2. All Daniel Senior O rifice Fittings are supplied with pipe plugs on one side only. If additional quantities are required, please contact the factory direct. * Indicates Interchangeable Parts for all line sizes of specified pressure rating(s). General Notes: Most parts available in other materials upon specification. CS (Carbon Steel), CP (Cadmium Plated). The materials listed above indicate standard A trim. Various part materials are changed for NACE & "AASG" trim fittings. Shaded part numbers are for items which are fluid media PIC (parts in contact). W HEN ORDERING PARTS, PLEASE SPECIFY: (1) catalog number, (2) size, (3) serial number and date of the original purchase, (4) part number, (5) material, (6) quantity of parts required.

INTRODUCTION

1-13

S E P 2006

DANIEL SENIOR ORIFICE FITTING

1-14

INTRODUCTION

DANIEL SENIOR ORIFICE FITTING

S E P 2006

All Parts on Daniel Senior Orifice Fittings may be replaced or repaired without removing the Daniel Senior Orifice Fitting body from the line.
PARTS AND M ATERIALS Part No. *1 * 1G * 1H * 1D * 1K * 1J *2 3 4 5
(3)

Description Equalizer Valve (Complete): Stem Packing Nut Ball Packing W asher Packing Ring Operating W rench Slide Valve Strip Body Slide Valve Gear Shaft Slide Valve Indicator Plate Slide Valve Indicator Pointer Lower Plate Carrier Gear Shaft Upper Plate Carrier Gear Shaft Plate Carrier Orifice Plate Sealing Unit Alternate Seals Available See Catalog - #500 Sealing Bar Sealing Bar Gasket Bleeder Valve (Complete): Body Needle "O" Ring Set Screw Clamping Bar Screw Clamping Bar Orifice Plate Top Slide Valve Springs Slide Valve Carrier Guide Slide Valve Carrier Slide Valve Carrier Stop Pin Slide Valve Seat Slide Valve Seat /Top Gasket

M aterial 316 Stainless Steel CS (CP) 18-8 Stainless Steel 17-4PH Stainless Steel Teflon Ductile Iron Type 410 Stainless Steel Cast Carbon Steel CS (CP) Cast Aluminum Stainless Steel CS (CP) CS (CP) CS (CP) Teflon (Removable)

NUM BER REQUIRED SIZE 10" 12" 14" 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 (3) 1 1 1 (3) 1 (3) 1 1

* 5A * 5B 6 (3) 7 (3) 8DM 8TS

9HP 9A-HP * 10B (1) * 10C * 10D * 10E * 10G * 11 12HP 13 14 * 15 * 16 17 * 17A 18 18A

CS (CP) Composite CS (CP) 316 Stainless Steel Synthetic Rubber Alloy Steel Alloy Steel (CP) CS (CP) Type 304 or 316 Stainless Steel Cast Carbon Steel 316 Stainless Steel 316 Stainless Steel Cast Alloy Iron Carbon Steel (CP) Type 410 Stainless Steel 17-4PH Stainless Steel Composite

1 1 1 1 1 1 16 1 1 1 6 2 1 2 1

1 1 1 1 1 1 20 1 1 1 7 2 1 2 1

1 1 1 1 1 1 22 1 1 1 8 2 1 2 1

INTRODUCTION

1-15

S E P 2006

DANIEL SENIOR ORIFICE FITTING

PARTS AND M ATERIALS Part No. 18VSG 18BTG * 18B * 22A * 23 * 24 * 25 * 25A * 25B * 26 * 30 * 31 32 33 * 34 * 35 * 36 * 37 38 39 40 41
(2) (2)

Description Slide Valve Seat Gasket Body /Top Gasket Slide Valve Seat Screw Bearing Plug and Stuffing Box Gasket Grease Gun (Complete) Grease Seal Double Ball Check Valve Packing Nut Packing Rings Centering Ring Stuffing Box Gland Drain Valve Plug "" N.P.T. Plug for Pressure Meter Tap Hex Nut Stud Bearing Plug Body (Upper) Bearing Plug Body (Lower) Stuffing Box Body (Upper) Stuffing Box Body (Lower) Bearing Plug Sleeve(Upper) Bearing Plug Sleeve (Lower) Stuffing Box Sleeve (Upper) Stuffing Box Sleeve (Lower)

M aterial Composite (not shown) Composite (not shown) Alloy Steel Phosphate Treat Stainless Steel CS (CP) 316 Stainless Steel with Chrome-Steel Balls CS (CP) Teflon Teflon 316 SS CS (CP) CS (Chemically Treated) CS Alloy Steel CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP) CS (CP)

NUM BER REQUIRED SIZE 10" 12" 14" 1 1 18 6 1 1 3 9 9 3 1 2 22 22 1 2 1 2 1 2 1 2 20 6 1 1 3 9 9 3 1 2 22 22 1 2 1 2 1 2 1 2 2 4 2 4 24 6 1 1 6 12 12 6 1 2 28 28

1-16

INTRODUCTION

DANIEL SENIOR ORIFICE FITTING

S E P 2006

Notes: 1. W hen venting upper chamber through bleeder valve (#10B), direct fluid and/or gas to a safe area using the threaded connection at the valve discharge port. 2. All Daniel Senior O rifice Fittings are supplied with pipe plugs on one side only. If additional quantities are required, please contact the factory direct. 3. 14" 1500 Gear Shafts are double-ended to allow operation from either side of the Daniel Senior Orifice Fitting. * Indicates Interchangeable Parts for all line sizes of specified pressure rating(s). General Notes: Most parts available in other materials upon specification. CS (Carbon Steel), CP (Cadmium Plated). The materials listed above indicate standard A trim. Various part materials are changed for NACE & "AASG" trim fittings. Shaded part numbers are for items which are fluid media PIC (parts in contact). W HEN ORDERING PARTS, PLEASE SPECIFY: (1) catalog number, (2) size, (3) serial number and date of the original purchase, (4) part number, (5) material, (6) quantity of parts required.

INTRODUCTION

1-17

S E P 2006

DANIEL SENIOR ORIFICE FITTING

This page intentionally left blank.

1-18

INTRODUCTION

DANIEL SENIOR ORIFICE FITTING

S E P 2006

2.0 INSTALLATION

Figure 2-1. Typical Configuration

2.1 Preliminary Steps The Daniel Senior Orifice Fitting is an essential element in an orifice plate flow measurement system. Other essential elements in the system include a meter tube, a flow conditioner, and a data recording device. If the Daniel Senior Orifice Fitting is shipped separately from a meter tube, it is the responsibility of the purchaser to assemble the meter tube and the fitting. See the appropriate code (AGA-3, etc.) for meter tube requirements.

INSTALLATION

2-1

S E P 2006

DANIEL SENIOR ORIFICE FITTING

On installations which require to comply with the European Union Pressure Equipment Directive (PED) 97/23/EC, it is the responsibility of the end user to ensure that all Essential Safety Requirements of this directive are met. Particular attention should be paid to the requirements for permanent joining and non-destructive testing. Before installing the fitting and meter tube assembly into the line, clean piping of all foreign material such as welding chips, scale, oil, grease, and dirt. Remove all foreign matter such as scale, oil, grease, and dirt from the fitting and meter tube piping and internal cavities of the fitting that may have collected during the time of final factory inspection and line installation. If the installation personnel expect the Daniel Senior Orifice Fitting to encounter severe conditions (conditions where there is likely to be an accumulation of sediment for any cause), installation personnel should install blow down valves in place of the pipe plugs (30) at the bottom of the fitting. Record the serial plate data for future reference. Always provide the serial number and model number of the fitting when ordering spare parts. Orifice plates and seal rings are packaged separately. It is the responsibility of the end user to install the fitting in a well designed piping system taking due regard of the following: Internal/external pressure Ambient and operational temperatures Static pressure and mass of contents in operating and test conditions Traffic, wind and earthquake loading Reaction forces and moments, which result from supports, attachments, piping, etc. Corrosion, erosion, fatigue, etc. Decomposition of unstable fluids Possible damage from external fire

2-2

INSTALLATION

DANIEL SENIOR ORIFICE FITTING 2.2 Daniel Senior Orifice Fitting Installation

S E P 2006

SERIOUS PERSONAL INJURY OR DEATH The Daniel Senior Orifice Fitting is a device that contains fluid at elevated pressure. Failure to follow the instructions in this manual can result in serious injury or death. Installation personnel must confirm that the line flow direction corresponds to the flow arrow cast on the Daniel Senior Orifice Fitting body. The Daniel Senior Orifice Fitting should be installed in any horizontal line with the plate access opening in a vertical up position or with the fitting rotated left or right to give a horizontal opening position. Daniel Senior Orifice Fittings to 12" size may be installed in a vertical down flow direction. 1. Confirm the operating clearance around the Daniel Senior Orifice Fitting. Clearance for both fitting wrench operation and plate changing must be verified. Check accessibility of all meter pressure taps (31) and drain taps (30) prior to installation. Check shipment to confirm that the shipping kit contains an operating wrench (2), grease gun (23), indicator plate (5A) and indicator pointer (5B). Install grease gun(s) (23) into holes in the base of the top chamber (14) by first removing plastic shipping plugs, putting thread sealer on end threads of grease gun body (23) and tightening securely.

2.

3.

INSTALLATION

2-3

S E P 2006

DANIEL SENIOR ORIFICE FITTING

4.

Install the indicator pointer (5B) in the top chamber (14) by tapping the two drive screws into the holes located above the slide valve shaft (5). Install the indicator plate (5B) on the slide valve shaft (5), directly below the pointer (5A). Orient the indicator plate (5B) as stated below depending on shaft location of right or left side: Shaft on left hand side facing with the flow (standard position): When the shaft is rotated clockwise until it stops, the indicator plate (5B) word OPEN should appear below the indicator pointer (5A). Install the indicator plate (5B) on the shaft in this position and tighten set screw securely. Shaft on right hand side facing with the flow (reverse shafts): When the shaft is rotated counterclockwise until it stops, the indicator plate (5B) word OPEN should appear below the indicator pointer (5A). Install the indicator plate (5B) on the shaft in this position and tighten the set screw securely. Note that right hand and left hand indicator plates (5B) are different and not interchangeable. After installation, rotate the slide valve shaft (5) until it stops. The word CLOSED should appear below the indicator pointer (5A).

5.

Daniel Senior Orifice Fittings leave the factory with the plate carriers (8DM or 8DMC) in the bottom chamber (4). Daniel ships the Daniel Senior Orifice Fitting in this manner to prevent plate carrier (8DM or 8DMC) or slide valve damage during transit. Whether or not the Daniel Senior Orifice Fitting arrives directly from the factory, installation personnel must open the top chamber (14) and slide valve to ensure that the plate carrier (8DM or 8DMC) is inside. The plate carrier (8DM or 8DMC) should be removed before performing any tests. With the slide valve in the fully opened position, rotate the lower plate carrier shaft (6) first, then the upper plate carrier shaft (7) to remove the carrier. Put the plate carrier (8DM or 8DMC) in a safe, protected area for use later in the installation process. Replace sealing bar (9 or 9HP), gasket (9A, 9A-HP or 9CF) and clamping bar (12 or 12HP) and tighten screws (11) to the required torque. Install gaskets on any line flanges and/or weld the meter tube in the line. If your Daniel Senior Orifice Fitting is a flanged model, installation personnel must tighten the flange bolts to the appropriate torque values for the flange rating.

6.

2-4

INSTALLATION

DANIEL SENIOR ORIFICE FITTING

S E P 2006

2.3 Line Pressure Test

SERIOUS PERSONAL INJURY OR DEATH The Daniel Senior Orifice Fitting is a device that contains fluid at elevated pressure. Failure to follow the instructions in this manual can result in serious injury or death. Once the Daniel Senior Orifice Fitting is installed and the top chamber (14) is sealed, the installation personnel can perform a pressure test for the line including the meter tube and Daniel Senior Orifice Fitting. Both the slide valve and the equalizer valve (1) should be in the OPEN position. The bleeder valve (10B) should be closed during the test. 1. Install a pressure gauge in a location that will indicate the pressure in the Daniel Senior Orifice Fitting. The gauge should have a maximum pressure range slightly above the maximum to be applied during the test. Slowly pressurize the Daniel Senior Orifice Fitting at a rate of 1 psig per second (0.15 bars per second) until the pressure inside the fitting reaches 20 psig (1.4 bar) then stop and hold that pressure for five minutes. During the five-minute hold, apply a leak detection solution to all joint and connector areas of the Daniel Senior Orifice Fitting and line connections. No leakage should be visibly detectable or audibly detectable during the hold period. If a leak is detected, mark the leak area with a marker and reduce the pressure inside the Daniel Senior Orifice Fitting to 0 psig (0 bar). Tighten any fastener or connector adjacent to the leak area and repeat the leak test again. If the leak persists after several attempts to stop it, call your Daniel Customer Service for assistance. Contact information is found in the back of this manual.

2.

3.

4.

INSTALLATION

2-5

S E P 2006

DANIEL SENIOR ORIFICE FITTING

SERIOUS PERSONAL INJURY OR DEATH Correct all leaks prior to operation. Failure to stop any size leak may lead to serious injury or death. 5. Once the 20 psig (1.4 bar) leak test is complete, and no leaks are detected, slowly raise the pressure inside the Daniel Senior Orifice Fitting at a rate of 10 psig per second to 1.5 times the maximum operating pressure of the lowest rated item in the system. Hold the 1.5 times maximum operating pressure on the system for a period of 10 minutes.

SERIOUS PERSONAL INJURY OR DEATH POSSIBLE Never exceed 1.5 times the maximum allowable operating pressure of the lowest rated item in the system. The installation technician must confirm the maximum allowable operating pressure (MAOP) of each item in the system, including the Daniel Senior Orifice Fitting, prior to performing this leak test. Failure to confirm the maximum allowable operating pressure of each item in the system could result in serious injury or death. 6. During the 10 minute hold period, apply a leak detection solution to all joint and connector areas of the Daniel Senior Orifice Fitting and line connections. No leakage should be visibly detectable or audibly detectable during the hold period. If a leak is detected, mark the leak area with a marker and reduce the pressure inside the Daniel Senior Orifice Fitting to 0 psig (0 bar). Tighten any fastener or connector adjacent to leak area and repeat leak test again. If the leak persists after several attempts to stop it, call Daniel Customer Service for assistance. Slowly release the pressure from the Daniel Senior Orifice Fitting until the gauge reads zero (0) psig. INSTALLATION

7.

8. 9.

2-6

DANIEL SENIOR ORIFICE FITTING

S E P 2006

2.4 Orifice Plate Installation

SERIOUS PERSONAL INJURY OR DEATH The Daniel Senior Orifice Fitting is a device that contains fluid at elevated pressure. Failure to follow the instructions in this manual can result in serious injury or death. After completion of the leak test, installation personnel must install and lower the plate carrier (8DM or 8DMC) and orifice plate assembly (13) into the body chamber (4) to begin measurement operations according to the steps below. 1. The Daniel Senior Orifice Fitting must be at atmospheric pressure (0 psig). Open bleeder valve (10B) to confirm no pressure is in the fitting. Bleeder valve (10B) to remain open. Confirm that the equalizer valve (1) is open. Remove clamping bar (12 or 12HP) by loosening all screws (11) two turns maximum and sliding bar from slot. Remove sealing bar (9) and gasket (9A, 9A-HP or 9CF). Confirm that the slide valve is still in the OPEN position.

2. 3.

4. 5.

INSTALLATION

2-7

S E P 2006

DANIEL SENIOR ORIFICE FITTING

6.

The orifice plate (13), with the appropriate seal ring, should be installed in the plate carrier (8DM or 8DMC). If a rubber seal is used, lubricate both seal faces with a light oil or grease. The assembly should then be inserted into the top (14) until the upper plate carrier gears mesh with the plate carrier rack. The gear shaft should then be rotated 1/4 turn in the OPPOSITE direction used for lowering the carrier, to allow the carrier to align itself with the gear teeth. Then lower the plate carrier assembly (8DM or 8DMC) from the top (14) to the bottom chamber (4) using the upper (7), then lower (6) gear shafts until it is completely inserted into the body chamber (4).

SERIOUS PERSONAL INJURY OR DEATH The correct positioning and installation of the gasket (9A, 9A-HP or 9CF), sealing bar (9), and clamping bar (12 or 12HP) are essential to provide a pressure barrier between the line pressure and atmospheric pressure. Failure to properly install the gasket, sealing bar, and clamping bar can result in serious injury or death. 7. Install the sealing bar (9), the gasket (9A, 9A-HP or 9CF), and clamping bar (12) in position on the top chamber (14) and tighten the fasteners (11). The operator will rotate the slide valve shaft (5) to the CLOSED position. This closes the slide valve, separating the body chamber (4) from the top chamber (14). Close both the equalizer (1) and bleeder valves (10B).

8.

9.

10. The Daniel Senior Orifice Fitting is now ready for final pressurization and operation.

2-8

INSTALLATION

DANIEL SENIOR ORIFICE FITTING

M A R 2003

3.0 MAINTENANCE

SERIOUS PERSONAL INJURY OR DEATH The Daniel Senior Orifice Fitting is a device that contains fluid at elevated pressure. Failure to follow the instructions in this manual can result in serious injury or death. 3.1 Normal Conditions Under normal measurement conditions, Daniel recommends that maintenance personnel both lubricate the slide valve and exercise several key components of the Daniel Senior Orifice Fitting every thirty days (See 3.1.2). If normal plate changing operations are performed within this period, omit this operation. 3.1.1 Lubrication This does not apply to Daniel Senior Orifice Fittings equipped with Soft Seat slide valves. In order to perform this operation: The slide valve must be in the "CLOSED" position, The bleeder valve (10B) must be in the "OPEN" position, The equalizer valve (1) must be in the "CLOSED" position, and The Daniel Senior Orifice Fitting must be under line pressure of 100 psig minimum.

MAINTENANCE

3-1

M A R 2003

DANIEL SENIOR ORIFICE FITTING

SERIOUS PERSONAL INJURY OR DEATH Opening the bleeder valve (10B) releases line pressure fluid into the atmosphere. Failure to direct the released pressurized fluid to a safe area during the discharge cycle may result in the release fluid causing contamination and/or the accumulation of volatile gas mixtures. Volatile gas mixtures are explosive and/or toxic and may lead to serious injury or death. 1. Once the maintenance personnel positions the valves as described above , remove the stem from the grease gun (23) and insert a Daniel lubricant stick into the grease gun (23). Return the stem to the grease gun (23) and begin turning the stem by hand into the grease gun (23) until resistance is felt. Once resistance is felt, use the supplied Daniel operating wrench (2) to continue to turn the stem at a very slow rate. By turning the stem slowly, the lubricant is forced through the grease channels at a rate that allows the lubricant to travel freely, yet not separate the valve strip from the valve seat. This will keep fresh grease in the lubrication passages. Close bleeder valve (10B).

2.

3.

4.

3-2

MAINTENANCE

DANIEL SENIOR ORIFICE FITTING

M A R 2003

3.1.2 Component Exercise In order to perform the following operations: The slide valve must be in the "CLOSED" position, The bleeder valve (10B) must be in the "CLOSED" position, and The equalizer valve (1) must be in the "OPEN" position.

At this point the fluid pressure in the body chamber (4) will equal the fluid pressure in the top chamber (14). 1. 2. Reduce the differential pressure across the meter to a maximum of 100 inches of H2O. Once the maintenance personnel position the valves as described above and the maximum differential across the meter is set, maintenance personnel should turn the plate carrier shaft (7) located in the top chamber (14) several times in both directions. The shaft (7) should turn freely. Rotate the slide valve shaft (5) in both directions until it stops. Repeat this action 2-3 times. The slide valve should travel freely in both directions with light resistance. Leave the valve in the OPEN position.

3.

MAINTENANCE

3-3

M A R 2003

DANIEL SENIOR ORIFICE FITTING

The following operation will affect the flowing differential and will be shown on any chart or instrument keeping records of differential unless these instruments are isolated. 4. Rotate the plate carrier shaft (6) located in the body chamber (4) one turn in both directions. This operation raises and lowers the plate carrier (8DM or 8DMC) in and out of the flow stream. An initially high resistance to turning will be encountered when the orifice plate seal is initially loosened from the Daniel Senior Orifice Fitting seal surface. Resistance to turning will also be present when the plate carrier (8DM or 8DMC) is lowered into position again. Return the plate carrier (8DM or 8DMC) to fully seated position in body. Close slide valve. Close Equalizer valve (1). If at any point during the exercise of the components, the resistance encountered when turning the shafts is greater than the torque applied by hand using the Daniel wrench (2), inspection of the Daniel Senior Orifice Fitting is required.

5.

6.

3-4

MAINTENANCE

DANIEL SENIOR ORIFICE FITTING

M A R 2003

4.0 OPERATING INSTRUCTIONS

SERIOUS PERSONAL INJURY OR DEATH The Daniel Senior Orifice Fitting is a device that contains fluid at elevated pressure. Failure to follow the instructions in this manual can result in serious injury or death. Daniel Senior Orifice Fittings dual chamber design allows an operator to install or remove the plate carrier (8DM or 8DMC) without flow interruption. An internally mounted slide valve separates the two chambers. The flow stream chamber or "body" chamber (4) contains the plate carrier (8DM or 8DMC) during measurement operations. The transfer chamber, or "top" chamber (14) contains the plate carrier (8DM or 8DMC) during inspection and replacement of the orifice plate (13). Within the Daniel Senior Orifice Fitting, is a rectangular plate or "plate carrier" (8DM or 8DMC) that positions the orifice plate (13) firmly in the flow stream. Formed along the edges of the plate carrier (8DM or 8DMC) are two gear tooth racks. Additionally, two pinion gears mounted on a shaft are positioned to mesh with the plate carrier gear tooth racks. There are two such shafts (6 & 7) located in the Daniel Senior Orifice Fitting, one in the body chamber (4) and one in the top chamber (14). By rotating these shafts (6 & 7) in sequence, an operator may move the plate carrier (8DM or 8DMC) into, or out of, the flow stream. During measurement operations the plate carrier (8DM or 8DMC), containing an orifice plate (13), is positioned in the flow stream. The slide valve is in the CLOSED position, separating the body chamber (4) from the top chamber (14).

OPERATING INSTRUCTIONS

4-1

M A R 2003

DANIEL SENIOR ORIFICE FITTING

4.1 Plate Removal Conditions: Daniel Senior Orifice Fitting operating at line pressure. Plate carrier (8DM or 8DMC) located in flow stream.

Procedure: 1. To remove the orifice plate (13) the operator must first balance the pressure between the body chamber and the top chamber (14). Open the equalizer valve (1) ( to 1 turn is sufficient). Wait several seconds while the top chamber (14) pressure equalizes with the actual line pressure. Rotate the slide valve shaft (5) until it stops and OPEN is indicated on the indicator plate. Rotate the plate carrier shaft (6) located in the body chamber (4) in a direction that will move the plate carrier (8DM or 8DMC) out of the body chamber (4) and into the upper gear shaft (7) located in the top chamber (14). Rotate the plate carrier shaft (7) located in the top chamber (14) in a direction that will lift the plate carrier (8DM or 8DMC) completely out of the body chamber and fully into the top chamber. Rotate shaft until the plate carrier (8DM or 8DMC) stops against the seal bar. Once the plate carrier (8DM or 8DMC) is completely out of the body chamber (4), rotate the slide valve shaft (5) to the CLOSED position. This rotation closes the slide valve thus separating and sealing the body chamber (4) from the top chamber (14). Close equalizer valve (1). Open the bleeder valve (10B).

2. 3.

4. 5.

6.

7.

8. 9.

4-2

OPERATING INSTRUCTIONS

DANIEL SENIOR ORIFICE FITTING

M A R 2003

SERIOUS PERSONAL INJURY OR DEATH Opening the bleeder valve (10B) releases line pressure fluid into the atmosphere. Failure to direct the released pressurized fluid to a safe area during the discharge cycle may result in the release fluid causing contamination and/or the accumulation of volatile gas mixtures. Volatile gas mixtures are explosive and/or toxic and may lead to serious injury or death. Once pressure in the top chamber (14) is reduced to ambient pressure, the operator may then extract the plate carrier (8DM or 8DMC), containing the orifice plate (13), from the Daniel Senior Orifice Fitting using the following steps.

SERIOUS PERSONAL INJURY OR DEATH POSSIBLE Never place any part of the head or body in front of the top opening when the clamping bar (12 or 12HP) is removed and the line is under pressure. Failure to keep clear of the top opening could result in serious injury or death. 10. Loosen (approximately two turns, but do not remove) each fastener (11), located in the clamping bar on the extreme end of the top chamber. 11. Once the fasteners (11) are loose, the operator should then turn the plate carrier shaft (7) located in the top chamber (14) in the direction to raise the plate carrier (8DM or 8DMC) and to tap the inside surface of the sealing bar (9) to free both it and the gasket. 12. Slide the clamping bar (12 or 12HP) containing the fasteners (11), sealing bar (9) and gasket (9A, 9-HP or 9CF) from the top chamber (14). The removal of these components exposes the interior of the top chamber.

OPERATING INSTRUCTIONS

4-3

M A R 2003

DANIEL SENIOR ORIFICE FITTING

SERIOUS PERSONAL INJURY OR DEATH POSSIBLE Never place any part of the head or body in front of the top opening when the clamping bar (12 or 12HP) is removed and the line is under pressure. Never place the operating wrench (2) on the slide valve shaft (5) when the clamping bar (12 or 12HP) is removed from the Daniel Senior Orifice Fitting and the line is under pressure. Failure to heed these warnings may result in serious injury or death.

13. Rotate the top chamber plate carrier shaft (7) to lift the plate carrier (8DM or 8DMC) out of the Daniel Senior Orifice Fitting. 4.2 Lubrication The following three steps are for Daniel Senior Orifice Fittings equipped with lubricated slide valves only. For Soft Seat equipped Daniel Senior Orifice Fittings, skip steps 1-3. 1. Lubricate the slide valve by removing the stem from the grease gun (23) and inserting a Daniel Lubricant Stick into the grease gun (23). Return the stem to the grease gun (23) and begin turning the stem by hand into the grease gun (23) until resistance is felt. Once resistance is felt, use the supplied Daniel operating wrench (2) to continue to turn the stem at a very slow rate. By turning the stem SLOWLY, the lubricant is forced through the grease channels at a rate that allows the lubricant to travel freely, yet not separate the valve strip from the valve seat. This will keep fresh grease in the lubrication passages and assist in sealing the valve. One stick of lubricant is normally sufficient for sizes to 12" and two sticks for 14" and larger.

2.

3.

4-4

OPERATING INSTRUCTIONS

DANIEL SENIOR ORIFICE FITTING

M A R 2003

If the addition of lubricant does not reduce the flow from the bleeder valve (10B) to near zero, close the bleeder valve (10B), open the equalizer valve (1) and crank the slide valve back and forth 2-3 times and then close the equalizer valve (1) and repeat the process. If excessive leakage still is present, close the slide valve and tag the Daniel Senior Orifice Fitting for maintenance.

4.3 Plate Insertion

EQUIPMENT DAMAGE OR PERSONAL INJURY Observe the instructions below if the listed conditions are present. Failure to do so may cause injury or damage to equipment. Conditions: Line at operating pressure. Slide valve in CLOSED position. Top chamber (14) evacuated and exposed to ambient pressure. Bleeder valve (10B) in the OPEN position. Equalizer valve (1) in the CLOSED position. Sealing bar (9 or 9HP), seal bar gasket (9A, 9A-HP or 9CF), and clamping bar (12 or 12HP) removed from top chamber (14).

OPERATING INSTRUCTIONS

4-5

M A R 2003

DANIEL SENIOR ORIFICE FITTING

SERIOUS PERSONAL INJURY OR DEATH POSSIBLE Never place any part of the head or body in front of the top opening when the clamping bar (12 or 12HP) is removed and the line is under pressure. Never place the operating wrench (2) on the slide valve shaft (5) when the clamping bar (12 or 12HP) is removed from the Daniel Senior Orifice Fitting and the line is under pressure. Failure to hear these warnings may result in serious injury or death.

Procedure: 1. Align the plate carrier (8DM OR 8DMC) and orifice plate assembly gear rack with the plate carrier shaft pinion gears and place the assembly into the top chamber (14) until the upper plate carrier gears mesh with the plate carrier rack. (If a rubber seal is used, lubricate both seal faces with a light oil or grease). The gear shaft should then be rotated 1/4 turn in the OPPOSITE direction used for lowering the carrier, to allow the carrier to align itself with the gear teeth.

2.

EQUIPMENT DAMAGE Align the plate carrier assembly (8DM or 8DMC) with the plate carrier shaft (7). Failure to align the plate carrier assembly with the plate carrier shaft may damage the Daniel Senior Orifice Fitting.

4-6

OPERATING INSTRUCTIONS

DANIEL SENIOR ORIFICE FITTING

M A R 2003

3.

Rotate the plate carrier shaft (7) in the direction that will lower the plate carrier (8DM or 8DMC) into the top chamber (14). Lower the plate carrier assembly (8DM or 8DMC) into the top chamber (14) until the plate carrier assembly JUST CLEARS the top surface of the opening.

4.

EQUIPMENT DAMAGE Do not lower the plate carrier (8DM or 8DMC) on to the slide valve as this may damage the precision machined surface. Failure to use caution while lowering the plate carrier (8DM or 8DMC) may cause equipment damage. 5. 6. 7. 8. Install a new seal bar gasket (9A, 9A-HP or 9CF). Replace the sealing bar (9 or 9HP). Slide the clamping bar (12 or 12HP) into position. Tighten each of the clamping bar screws (11) to the torque recommended in Section 5.3 of this manual.

SERIOUS PERSONAL INJURY OR DEATH The correct positioning and installation of the gasket, sealing bar, and clamping bar are essential to provide a pressure barrier between the line pressure and atmospheric pressure. Failure to properly install the gasket, sealing bar, and clamping bar can result in serious injury or death.

OPERATING INSTRUCTIONS

4-7

M A R 2003

DANIEL SENIOR ORIFICE FITTING

9.

Close the bleeder valve (10B).

10. Open the equalizer valve (1) ( to 1 turn is sufficient). 11. Wait several seconds while the top chamber pressure equalizes with the actual line pressure. 12. Rotate the slide valve shaft (5) until it stops in the OPEN position. 13. Rotate the plate carrier shaft (7) located in the top chamber in the direction that will lower the plate carrier assembly (8DM or 8DMC) into the bottom chamber (4). 14. Rotate the plate carrier shaft (6) located in the body chamber (4) in the direction that will lower the plate carrier assembly (8DM or 8DMC) into the body chamber (4). Turn shaft until a solid stop is felt. Resistance to turning will be present when the plate carrier (8DM or 8DMC) is approaching its measurement position due to the friction between the fitting body and the plate carrier assembly seals. 15. Once the plate carrier (8DM or 8DMC) is positioned in the body chamber (4), turn the slide valve shaft (5) in the direction of flow. This rotation closes the slide valve thus separating the body chamber (4) from the top chamber (14). 16. Close the equalizer valve (1). 17. Open the bleeder valve (10B).

SERIOUS PERSONAL INJURY OR DEATH Opening the bleeder valve (10B) releases line pressure fluid into the atmosphere. Failure to direct the released pressurized fluid to a safe area during the discharge cycle may result in the release fluid causing contamination and/or the accumulation of volatile gas mixtures. Volatile gas mixtures are explosive and/or toxic and may lead to serious injury or death.

4-8

OPERATING INSTRUCTIONS

DANIEL SENIOR ORIFICE FITTING

M A R 2003

18. To lubricate the Daniel Senior Orifice Fitting (see Lubrication Section 4.2 or Lubricant Information Section 5.2). Not applicable for Soft Seat Daniel Senior Orifice Fitting. 19. Close the bleeder valve (10B).

OPERATING INSTRUCTIONS

4-9

M A R 2003

DANIEL SENIOR ORIFICE FITTING

This page intentionally left blank.

4-10

OPERATING INSTRUCTIONS

DANIEL SENIOR ORIFICE FITTING

S E P 2006

5.0 SUPPLEMENTAL INFORMATION 5.1 Recommended Spare Parts for One-Year Operation

- PRICES ON APPLICATION QUANTITY 1 5 3 5 3 2 1 1 1 1 2 2 2 1-SET 1-SET 1-SET 1-SET 1 1 1 3 BOXES PART NO. 5 8E 8TS 9A 9CF 11 18A 18A 14CF 14CF-C 22A 22A 22B 25A 25A-HP 25B 25B-HP 26C 26D 26D DANIEL 150-2500 150-600 900-2500 150-900 1500-2500 150-2500 150-900 1500 1500 2500 150-1500 2500 2500 150-1500 2500 150-1500 2500 2500 2500 2500 150-2500 DESCRIPTION Gear Shaft Orifice Plate Sealing Unit Orifice Plate Sealing Unit Sealing Bar Gasket Sealing Bar Gasket Clamping Bar Screws Slide Valve Seat/Top Gasket Slide Valve Seat/Top Gasket Body/Top Gasket (o-ring) Body/Top Gasket Stuffing Box/Bearing Plug Gasket Stuffing Box/Bearing Plug Gasket Stuffing Box/Bearing Plug O-Ring Packing Rings Packing Rings Centering Rings Centering Rings External Gland Outer O-Ring External Gland Inner O-Ring Internal Gland O-Ring Slide Valve Lubricant M ATERIAL CS (CP) Nitrile Teflon Composition Synthetic Composition Alloy Steel, CP Composition Composition Special Compound Parker Seal Stainless Steel Stainless Steel Nitrile Teflon Teflon Teflon Teflon Nitrile Nitrile Nitrile

IM PORTANT - See ordering information in Section 1.

SUPPLEMENTAL INFORMATION

5-1

S E P 2006

DANIEL SENIOR ORIFICE FITTING

5.2 Lubricant Information Daniel recommends the use of "DANIEL TYPE 1" lubricant for use in Daniel Senior Orifice Fittings. "DANIEL TYPE 1" is ideal for lubricating the slide valve thus insuring maximum operating performance. "DANIEL TYPE 1" lubricant is not a petroleum base product. Therefore, the "DANIEL TYPE 1" has the following advantages over other products: Operating temperature range for lubricant: -20OF (-29OC) to +450OF (+232OC). Contains no fillers or inert materials to reduce hardening and oxidizing. Is insoluble in water. (Preferred solvent is Castor Oil). Resistant to hydrocarbons within it's operating temperature range. Supplied in B size sticks to fit in the supplied grease gun.

Specialty lubricants for difficult services (sour gas, high temperature, etc) are available on request.

5.3 Screw and Stud Torque Tables

SEAT SCREW TORQUE FT-LBS SIZE STD Trim 2" - 8" STD Trim 10" STD Trim 12" + 316, Monel & all AASG TORQUE 45 50 55 35

5-2

SUPPLEMENTAL INFORMATION

DANIEL SENIOR ORIFICE FITTING

S E P 2006

CLAM PING BAR SCREW TORQUE FT-LBS SIZE DANIEL 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 NO. OF SCREW S 4 4 4 4 8 10 4 4 4 4 10 10 5 5 5 5 12 12 6 6 6 6 14 14 7 7 7 7 16 8 8 8 8 16 10 10 10 10 20 11 11 11 22 SCREW SIZE 1/2"-13 1/2"-13 1/2"-13 1/2"-13 5/8"-11 5/8"-11 1/2"-13 1/2"-13 1/2"-13 1/2"-13 5/8"-11 5/8"-11 1/2"-13 1/2"-13 1/2"-13 1/2"-13 5/8"-11 5/8"-11 1/2"-13 1/2"-13 1/2"-13 1/2"-13 5/8"-11 5/8"-11 1/2"-13 1/2"-13 1/2"-13 1/2"-13 5/8"-11 1/2"-13 1/2"-13 1/2"-13 5/8"-11 5/8"-11 1/2"-13 1/2"-13 1/2"-13 5/8"-11 5/8"-11 1/2"-13 1/2"-13 1/2"-13 5/8"-11 TORQUE 40 45 50 70 80 135 50 55 65 75 80 135 45 50 55 70 80 130 40 45 60 75 85 140 40 50 60 80 90 45 50 70 115 105 40 50 60 100 100 45 55 65 75

2"

3"

4"

6"

8"

10"

12"

14"

SUPPLEMENTAL INFORMATION

5-3

S E P 2006

DANIEL SENIOR ORIFICE FITTING

DANIEL SENIOR ORIFICE FITTING STUD TORQUE FT-LBS SIZE DANIEL 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 NO. OF SCREW S 14 14 14 14 14 16 15 15 15 15 15 16 15 15 15 15 16 16 18 18 18 18 18 18 19 19 19 20 18 22 22 22 22 22 22 22 22 22 22 24 24 24 24 SCREW SIZE 5/8"-18 5/8"-18 5/8"-18 3/4"-16 3/4"-16 1 1/8"-12 5/8"-18 5/8"-18 5/8"-18 3/4"-16 3/4"-16 1 1/8"-12 3/4"-16 3/4"-16 3/4"-16 3/4"-16 1" - 14 1 1/8"-12 3/4"-16 3/4"-16 3/4"-16 3/4"-16 1" - 14 1 1/8"-12 3/4"-16 3/4"-16 3/4"-16 1" - 14 1 1/8"-12 3/4"-16 3/4"-16 3/4"-16 1" - 14 1" - 14 3/4"-16 3/4"-16 3/4"-16 1 1/8"-12 1 1/8"-12 3/4"-16 3/4"-16 7/8"-14 7/8"-14 TORQUE 40 50 65 100 160 375 50 60 80 115 160 375 60 75 100 130 265 510 70 85 115 140 285 425 70 85 120 190 460 70 85 120 210 300 105 120 160 290 500 90 110 175 225

2"

3"

4"

6"

8"

10"

12"

14"

5-4

SUPPLEMENTAL INFORMATION

DANIEL MEASUREMENT AND CONTROL, INC. RETURN POLICY FOR WARRANTY AND NON-WARRANTY MATERIAL
Use the following procedure for returning equipment to the Daniel factory in the United States.

Step 1

Obtaining a RMA Number

A Return Material Authorization (RMA) number must be obtained prior to returning any equipment for any reason. To obtain a RMA number, call the Customer Service Department at 713-827-5033 between 8:00 a.m. and 5:00 p.m. (Central Standard Time), Monday through Friday, except holidays or email daniel.support@emersonprocess.com.

No product returns will be accepted without a RMA number and will be returned at the customers expense. For warranty consideration, the product must be returned to Daniel within twelve (12) months of the date of original shipment or within eighteen (18) months of the date of original shipment of the product to destinations outside the United States. The Purchaser must prepay any shipping charges. In addition, the Purchaser is responsible for insuring any product shipped for return, and assumes the risk of loss of the product during shipment. The following information is required at the time the RMA is issued: Customer name Contact name Billing address Contact Phone # and email address Daniel SO #, PO #, or Invoice # Item(s) to be returned Reason for return End user and final destination address Consignees complete name, address, contact name and phone number A RMA number is required for each original order. (Example: Two fittings purchased on two separate orders now being returned require two RMA numbers.) For product returns from locations outside the United States, Daniel Customer Service personnel will provide additional shipping requirements.

Step 2

Cleaning and Decontamination

Prior to shipment, thoroughly clean and decontaminate all equipment removing all foreign substances. This includes all substances used for cleaning the equipment. The cleaning and decontamination requirement applies to any part exposed to process fluids or cleaning substances. Shipping equipment that has not been decontaminated may be in violation of U.S. Department of Transportation (DOT) regulations. For your reference, the requirements for packaging and labeling hazardous substances are listed in DOT regulations 49 CFR 172, 178, and 179. If you suspect that a part has been contaminated, the part must be completely drained and flushed to remove contaminants.

MAY CAUSE DEATH OR SERIOUS INJURY TO PERSONNEL Contents may be under pressure or materials may be hazardous Follow appropriate handling instructions for accessing pressurized equipment. Avoid contact with hazardous materials or contaminated units and parts. Failure to do so may result in death or serious injury. Decontamination/Cleaning Statement A blank Decontamination/Cleaning Statement is provided on the Returned Material Authorization Repair Form for Used Equipment. A Decontamination/Cleaning Statement is required for each returned part. Fully complete each form and include a signature. If the decontamination statement is incomplete, the customer may be charged for decontamination and cleaning.

If the equipment has been exposed to a known hazardous substance with any characteristic that can be identified in the Code of Federal Regulations, 40 CFR 261.20 through 261.24, the chemical abstracts number and hazardous waste number/hazard code must be stated in the space provided on the form. Two (2) copies of each Decontamination/Cleaning Statement must be provided: One (1) copy must be attached to the outside of the package. One (1) copy must be included inside the package.

Step 3

Material Safety Data Sheets (MSDS)

Provide a Material Safety Data Sheet (MSDS) with the returned equipment for each substance that has come in contact with the equipment being returned, including substances used for decontamination and cleaning. A MSDS sheet is required by law to be available to people exposed to specific hazardous substances, with one exception: if the equipment has only been exposed to food-grade substances or potable water, or other substances for which an MSDS is not applicable, the Decontamination/Cleaning Statement form alone is acceptable. Two (2) copies of each MSDS must be provided: One (1) copy must be attached to the outside of the package. One (1) copy must be provided inside the package.

Step 4

Packaging

Shipping a Device With Possible Contamination To meet DOT requirements for identifying hazardous substances, ship only one device per package. Shipping a Device Without Any Potential Contamination Devices being returned may be shipped together in one package, if there is no potential of foreign substance contamination.

Step 5

Shipping

Before returning used equipment: Mark each package clearly with a RMA number. Include a Decontamination/Cleaning Statement inside the package. Attach a duplicate Decontamination/Cleaning statement to the outside of the package. Include a MSDS for each substance that has come in contact with the equipment inside the package. Attach a duplicate MSDS to the outside of the package.

No product returns will be accepted without a RMA number and will be returned at the customers expense. For warranty consideration, the product must be returned to Daniel within twelve (12) months of the date of original shipment or within eighteen (18) months of the date of original shipment of the product to destinations outside the United States. The Purchaser must prepay any shipping charges.

Ship all * mechanical equipment to the following address: Daniel Measurement and Control, Inc. Attn: Service Dept. 5650 Brittmoore Rd. Houston, TX 77041 Ref: RMA#____________________ *Mechanical equipment includes: Orifice Fittings, Parts, Plates, Seal Rings, Turbine Meters, Control Valves, Provers, Strainers, Meter Tubes, Ultrasonic Meters, Flow Conditioners, etc.

Ship all * electronic equipment to the following address: Daniel Measurement and Control, Inc. Attn: Service Dept. 11100 Brittmoore Park Drive Houston, TX 77041 Ref: RMA#____________________ *Electronic equipment includes: Gas Chromatographs, Petrocount Presets, Danload Preset, Ultrasonic Meter Electronics (CPU boards, transducers, etc.), 2403 Totalizer, MRT 97 Indicator, Preamps, Pick Up Coils, Prover Interface Boards, and the following Flow Computer Models: 2230, 2239, 2270, 2460, 2470, S100, 2100, and 3000.

Daniel Measurement and Control, Inc. Returned Material Authorization

Repair Form for Used Equipment Including Decontamination/Cleaning Statement 1. Return Material Authorization (RMA) Number ____________________________________ 2. Equipment to be returned: Model Number _________________________ Serial Number _______________________ 3. Reason for return: ___________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ Decontamination/Cleaning Fluids Process
A. List each substance in which the equipment was exposed. Attach additional documents if necessary. Common Name CAS# if available Used for Hazardous Waste (20 CFR 261) [ ] Yes [ ] Yes [ ] Yes [ ] Yes [ ] Yes [ ] Yes B. Circle any hazards and/or process fluid types that apply: Infectious Cyanides Carcinogen Radioactive Sulfides Peroxide Explosive Corrosive Reactive-Air Pyrophoric Oxidizer Reactive-Water Poison Gas Flammable Reactive-Other (list) Poison [ ] No [ ] No [ ] No [ ] No [ ] No [ ] No EPA Waste Code if used for hazardous waste

Other hazard category (list):

C.

Describe decontamination/cleaning process. Include MSDS description for substances used in decontamination and cleaning processes. Attach additional documents if necessary.

Shipping Requirements
Failure to comply with this procedure will result in the shipment being refused. 4. Write the RMA number on the shipping package. 5. Inside the package include one copy of this document and all required Material Safety Data Sheets (MSDS) 6. Outside of the package attach one copy of this document and all required Material Safety Data Sheets (MSDS). THIS EQUIPMENT, BEING RETURNED FOR REPAIR, HAS BEEN COMPLETELY DECONTAMINATED AND CLEANED. ALL FOREIGN SUBSTANCES HAVE BEEN DOCUMENTED ABOVE AND MSDS SHEETS ARE ATTACHED.
By:
(Signature) (Print name)

Title: Company: Phone:

Date:

Fax:

The sales and service offices of Daniel Measurement and Control are located throughout the United States and in major countries overseas. Please contact Daniel Measurement Services at 11100 Brittmoore Park Drive, Houston, Texas 77041, or phone (713) 827-6314 for the location of the sales or service office nearest you. Daniel Measurement Services offers both on-call and contract maintenance service designed to provide single-source responsibility for all Daniel products.

Daniel Measurement and Control, Inc., and Daniel Measurement Services, Inc. Divisions of Emerson Process Management reserves the right to make changes to any of its products or services at any time without prior notification in order to improve that product or service and to supply the best product or service possible. www.emersonprocess.com/daniel