This document summarizes an applications manual for a Jaguar immobilizer system. It provides information on the vehicle applications that use specific immobilizer cables, instructions on locating connectors for different vehicle models (XJ, XK, X-Type, S-Type), describes the general operation of the passive immobilizer system using transponder keys, and provides procedures for programming new keys and checking the number of keys programmed. It also outlines special functions for clearing the immobilizer system memory and reprogramming keys.
This document summarizes an applications manual for a Jaguar immobilizer system. It provides information on the vehicle applications that use specific immobilizer cables, instructions on locating connectors for different vehicle models (XJ, XK, X-Type, S-Type), describes the general operation of the passive immobilizer system using transponder keys, and provides procedures for programming new keys and checking the number of keys programmed. It also outlines special functions for clearing the immobilizer system memory and reprogramming keys.
This document summarizes an applications manual for a Jaguar immobilizer system. It provides information on the vehicle applications that use specific immobilizer cables, instructions on locating connectors for different vehicle models (XJ, XK, X-Type, S-Type), describes the general operation of the passive immobilizer system using transponder keys, and provides procedures for programming new keys and checking the number of keys programmed. It also outlines special functions for clearing the immobilizer system memory and reprogramming keys.
This document summarizes an applications manual for a Jaguar immobilizer system. It provides information on the vehicle applications that use specific immobilizer cables, instructions on locating connectors for different vehicle models (XJ, XK, X-Type, S-Type), describes the general operation of the passive immobilizer system using transponder keys, and provides procedures for programming new keys and checking the number of keys programmed. It also outlines special functions for clearing the immobilizer system memory and reprogramming keys.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 8
APPLICATIONS MANUAL
JAGUAR IMMOBILISER
CONTENTS APPLICATIONS CONNECTOR LOCATIONS GENERAL OPERATION SPECIAL FUNCTIONS
PAGE
1.1 2.1 3.1 4.1
APM105
Version 1.0 07/01
APPLICATIONS VEHICLE XJ TYPE PETROL KEYS 2 KEYS CABLE ADC110
XK
PETROL
2 KEYS
ADC110
X-TYPE
PETROL
2 KEYS
ADC110
S-TYPE
PETROL
2 KEYS
ADC110
1.1
CONNECTOR LOCATIONS XJ
XK
2.1
CONNECTOR LOCATIONS
X-TYPE
S-TYPE
2.2
GENERAL OPERATION SYSTEM OPERATION The PATS system is a PASSIVE Anti-theft system which requires no special procedures for the driver to arm or disarm the system. The system is operated by a transponder fitted within the ignition keys body, which communicates with the PATS module transceiver mounted around the lock barrel. The easy method of identifying a PATS vehicle is if the key has a small imprint showing where the transponder is fitted. The code for the transponder is stored in memory within the PATS amplifier or the Engine Management ECU, Dash panel or Drive Train ECU. The PATS system reads the code when the ignition key is turned from position 0 to position 1. If the correct code is received then the engine will start.
KEY PROGRAMMING NOTE : Clear ALL Fault codes before programming. Master keys can only be programmed using the 2 PATS keys (A and B) the WDS or the AD100 system. NOTE : In some cases the vehicle doors must be closed to perform the re-programming sequence. Further slaves can be added without any specialist equipment as follows :1. Insert key A, and turn to Position 2. 2. Turn back to Position 0, and remove key A. 3. Insert key B, and turn to Position 2. 4. Turn back to Position 0, and remove key B. 5. Insert the new slave key and turn to Position 2. 6. Remove new key. Key is now programmed. 7. Procedure can be repeated after 20 seconds, for up to 8 slave keys. NOTE : If programming is unsuccessful, the PATS LED will flash when the key is inserted.
3.1
SPECIAL FUNCTIONS CLEARING PATS 3 SYSTEM CLEAR PATS 3 SYSTEM MIN KEYS REQUIRED : 2 TIMED ACCESS CLEAR TIME 10:00 KEYS PROGRAMMED : 2 PRESS ENTER KEY CLEAR PATS 3 KEY GAINING ACCESS TIME ELAPSED 0:50 TIME REQUIRED 10:00 ACCESS STATUS IN PROGRESS BACK TO ABORT
Follow the screen instructions to clear the PATS system.
The AD100 will now start to clear the PATS system key codes from memory.
READING KEY 1 STORING KEY 1
After clearing, the PATS system will automatically read the key in the ignition.
KEY 1 IGN OFF TO KEY 2 IGN ON WITHIN 5 SECONDS PRESS ENTER KEY
Follow the instructions to program the second key. Once ENTER has been pressed, you have 5 seconds to insert the second key.
REMOVE KEY 1 INSERT KEY 2
4.1
SPECIAL FUNCTIONS CLEARING PATS 3 SYSTEM The PATS system will read the second key and store the code in the memory. The AD100 will now indicate how many keys are programmed After programming insert both keys and switch IGNITION ON before starting the vehicle.
READING KEY 2 STORING KEY 2
KEYS PROGRAMMED : 2
Further keys can be programmed by following the procedures in GENERAL OPERATION.
PRESS ENTER KEY
4.2
SPECIAL FUNCTIONS CHECKING KEYS PROGRAMMED DIAGNOSTIC MENU CLEAR PATS SYSTEM KEYS PROGRAMMED Using the UP and DOWN keys select the KEYS PROGRAMMED.
>
PRESS ENTER KEY
KEYS PROGRAMMED 2
The number of keys stored in the Immobiliser ECU will be displayed.
