T 1000 PLUS

Secondary Injection Relay Test Set

Designed for testing relays and transducers Microprocessor controlled With phase angle shifter Frequency generator Test results and settings are saved into local memory High power outputs Oscilloscope function for current and voltage Large graphical display Compact and lightweight Possibility to synchronize several T 1000 PLUS test sets USB interface 2 auxiliary contacts for the test of autoreclosers

The relay test set T 1000 PLUS is suited for the testing of the following types of relays:

RELAY TYPE
Distance relay (3 sets) Synchronizing device Thermal Under/over-voltage relay Directional Power relay Undercorrent Negative sequence over-currrent Phase sequence voltage relay Incomplete sequence relay Definite time over-current relay Inverse time over-current relay Power factor relay Voltage balance relay Ground detector relay Directional over-current relay Directional earth fault Automatic reclosing Frequency relay Load shed Pilot wire receiver relay Motor protection Differential protection relay (TD 1000) Voltage directional relay Tripping relay

IEEE NO
21 25 26 27/59 32/92 37 46 47 48 50/50N 51/51N 55 60 64 67 67N 79 81>/81< 81R 85 86 87 91 94

T 1000 PLUS

The instrument contains three separate generators: . Main generator, that generates either AC current, AC voltage; DC voltage; . Auxiliary AC voltage generator, that generates an independent, phase shiftable AC voltage; . Auxiliary DC voltage generator, that generates the DC voltage that powers the relay under test. All outputs are adjustable and metered at the same time on the large, graphic LCD display. T 1000 PLUS can operate without connection to a PC. With the multi-purpose knob and the LCD display it is possible to enter the MENU mode, that allows to set many functions, that make T 1000 PLUS a very powerful testing device, with manual and semi-automatic testing capabilities, and with the possibility to transfer test results to a PC via USB interface. These results can be recorded, displayed and analysed by the powerful TDMS software, that operates with all WINDOWS versions, starting from WINDOWS 98 included.

DC voltage outputs RANGE VOLTAGE V OUTPUT DC V 300 300 300 MAXIMUM POWER W 300 500 LOAD TIME s steady 10 RECOVERY TIME min 45

Other features of main outputs

. Zero crossing control. Main AC outputs are generated and stopped as the output waveform crosses zero. . High resolution adjustment control. . Overload alarm message. . Thermal protection. . Possibility to reduce the output power to one fifth for low burdens.

Auxiliary AC voltage output

. The auxiliary AC voltage output is isolated from the main AC current and voltage. . Range selection: software driven, by the multi-function knob and LCD display. . Auxiliary voltage power: 30 VA, continuous duty, at full range; 40 VA for 1 minute. . Push-button to enable or disable the output Auxiliary AC voltage output RANGE V 65 130 260 MAX POWER VA 40 40 40

T 1000 PLUS Specification

Main generator The main generator has three outputs: currents, voltage AC, voltage DC. The following specifications apply to the separate usage of these outputs. AC current outputs RANGE CURRENT A OUTPUT AC A 100 30 100 250 12 40 5 10 MAXIMUM POWER VA 300 800 1000 300 800 400 800 LOAD TIME s steady 60 1 steady 60 steady 60 RECOVERY TIME min 15 5 15 15

Phase angle shifting

. Possibility to phase shift the auxiliary AC voltage output with respect to the main current or voltage. . Phase angle adjustment: via the multi-function knob. . Phase angle range: from 0 to 360. . Adjustment resolution: 1 (degree).

40 10

Frequency generator & frequency r.o.c.

AC voltage outputs RANGE VOLTAGE V OUTPUT AC V 250 250 250 MAXIMUM POWER VA 500 750 LOAD TIME s steady 10 RECOVERY TIME min 45 . Possibility to change the frequency of the auxiliary AC voltage output. Frequency generation characteristics: . Frequency range: 15 Hz to 550 Hz. . Frequency adjustment: 1 mHz. . Rate of change: 1 mHz/s to 99.99 Hz/s.

T 1000 PLUS

SECONDARY INJECTION RELAY TEST SET

Auxiliary DC voltage output

. DC voltage range: 10...130 V or 20...240 V. . DC voltage power: 90 W at full range, continuous duty, with a current limit of 0.9 A @ 130 V and 0.45 A @ 240 V. . Push-button to enable or disable the output

Voltage measurement OUTPUT 250 V AC RANGE RESOLUTION 10 100 300 10 100 300 10 100 10 100 300 10 100 10 100 300 mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV ACCURACY (1% + 50 mV) (1% + 200 mV) (1% + 300 mV) (0.5% + 50 mV) (0.5% + 200 mV) (0.5% + 300 mV) (1% + 20 mV) (1% + 200 mV) (1% + 20 mV) (1% + 200 mV) (1% + 300 mV) (0.5% + 20 mV) (0.5% + 200 mV) (0.5% + 20 mV) (0.5% + 200 mV) (0.5% + 300 mV)

Timer
The electronic digital timer has a fully automatic start and stop, both for make and break of the input, that can be either a clean (dry) contact or a contact under voltage (wet). . Metering range, can also be performed in cycles. . Possibility to test automatic reclosers. . Maximum number of reclosing commands: 99.

RANGE From 0 to 9.999 s From 10.0 to 99.99 s From 100.0 to 999.9 s From 1.000 to 9.999 s

RESOLUTION 1 ms 10 ms 100 ms 1s

ACCURACY (1 ms + 0.005%) (10 ms + 0.005%) (100 ms + 0.005%) (1 s + 0.005%)

19.99 V 199.9 V 299.9 V 300 V DC 19.99 V 199.9 V 399.9 V 65,130 V AC 19.99 V 199.9 V 260 V AC 19.99 V 199.9 V 299.9 V 130 V DC 19.99 V 199.9 V 260 V DC 19.99 V 199.9 V 299.9 V

Angle and frequency measurement

. Via the multi-function menu knob it is possible to select the measurement of angle or frequency. . Readings, resolution and accuracy: see table. MEASUREMENT RANGE Phase Frequency 0-360 40.000-499.999 RESOLUTION ACCURACY 1 1 mHz 1 1 Digit (0.1% + 1 mHz)

2 auxiliary contacts are available

. Contacts range: 5 A; 250 V AC; 120 V DC.

OUTPUT CURRENT AND VOLTAGE MEASUREMENTS

. The following outputs are displayed at the same time on the LCD: Current measurement OUTPUT 10 A 40 A 100 A RANGE 1.999 A 19.99 A 7.999 A 79.99 A 19.99 A 199.9 A 249.9 A RESOLUTION 1 10 4 40 10 100 100 mA mA mA mA mA mA mA ACCURACY (1% + 5 mA) (1% + 20 mA) (1% + 20 mA) (1% + 80 mA) (1% + 50 mA) (1% + 200 mA) (1% + 200 mA)

Other measurements
MEASUREMENT Active Power, P = I*V*cos (j) Reactive Power, Q = I*V*sin(j) Apparent Power, S = I*V Impedance, Z = V/I Active Impedance Component, R = Z* cos(j) Reactive Impedance Component, X = Z* sin(j) UNIT W VAr VA Ohm, Ohm Ohm

External inputs measurement

. It is possible to meter current or voltage input.

External current measurement

. Two inputs: 20 mA and 10 A.

T 1000 PLUS

. Range, resolution, accuracy: see table below. INPUT 20 mA 10 A 10 A 10 A 10 A RANGE 0.02 A DC 1.999 A AC 9.99 A AC 1.999 A DC 9.99 A DC RESOLUTION 0.1 1 10 1 10 mA mA mA mA mA ACCURACY (0.5% + 0.1 mA) (1% + 2 mA) (1% + 20 mA) (0.5% + 2 mA) (0.5% + 20 mA)

Power supply
. Mains supply to be clearly indicated in purchase order: 230 V 15% 50-60 Hz or 120 V 15%50-60 Hz . Maximum supply current: 5 A.

Standard accessories
The instrument comes complete with the following items: . Set of standard test cables; . Mains cable; . USB cable; . Users manual; . Spare fuses (no. 5), T5A. . Software TDMS with serial cable.

External voltage measurement

. Maximum input voltage: 600 V, AC or DC. . Range, resolution and accuracy: see table below. RANGE 9.999 V AC 99.99 V AC 599.9 V AC 9.999 V DC 99.99 V DC 599.9 V DC RESOLUTION 2 10 100 2 10 100 mV mV mV mV mV mV ACCURACY (1% + 10 mV) (1% + 20 mV) (1% + 200 mV) (0.5% + 10 mV) (0.5% + 20 mV) (0.5% + 200 mV)

OTHER CHARACTERISTICS
T 1000 PLUS local memory
. Test settings can be stored and recalled from the T 1000 PLUS local memory: up to 10 test settings. . Test results can be saved into a permanent local memory: up to 500 test results saved. . When the PC is connected setting can also be created and transferred into T 1000 PLUS using the software TDMS. . When the PC is connected test results can be transferred to the PC via USB port using the software TDMS, for saving and printing.

TDMS - Relay Test Result

Weight and dimension

. Dimensions: 380 (w) x 300 (d) x 240 (h) mm. . Weight: 19 kg.

Resistors
A set of resistors is supplied for the test of low impedance relays. Available values: RESISTANCE OHM 0,5 1 22 470 1000 2200 POWER W 50 50 50 50 50 50 MAX CURRENT A 10 7 2.15 0.33 0.22 0.15

Case
Alluminium case with cover and handle.

Interface
. Interfaces for connection to PC: USB.
4

T 1000 PLUS

SECONDARY INJECTION RELAY TEST SET

TD 1000 PLUS
With two current outputs to test differential relay

TD 1000 PLUS 15 HZ
With two current outputs to test differential relay and with high power at 15 Hz
TD 1000 Plus 15 Hz is identical to TD 1000 Plus except for the high power and full range at 15 Hz. This allows testing old railway and generator protection relays. TD 1000 Plus 15 Hz does NOT have the DC battery simulator.

TD 1000 Plus has two current outputs to test differential relay characteristic curve and not only the pick-up current. In addition, the frequency of this current can be changed as with voltages: this allows to test the second harmonic restraint characteristic of the differential relay. Last, the steady voltage output power is increased from 30 VA to 50 VA. . Auxiliary AC voltage. Power: 40 VA, continuous duty, at full range; 50 VA for 1 minute. For lower voltages the limiting current is the following. . Power at 15 Hz: 25 VA on all ranges. . No Auxiliary DC voltage supply. . Weight: 21 kg. All other performances are the same as T 1000 Plus. The request of this model must be specified at order.

MAX CURRENT A 20

VOLTAGE V 3

All other performances are the same as T 1000 Plus. The request of this model must be specified at order.

T 1000 PLUS

T 1000-E PLUS
Higher AC voltage outputs
In this model, AC voltage outputs are higher than in the standard version. . Main AC voltage output. . Auxiliary AC voltage. Power: 30 VA, continuous duty, at full range; 40 VA for 1 minute. For lower voltages the limiting current is the following. RANGE V 65 130 500 MAX CURRENT mA 500 250 62
T 1000 PLUS - Standard cable kit

All other performances are the same. The request of this model must be specified at order.

OPTIONS
Heavy duty transport case
Heavy duty transport case in black plastics, with wheels, cover and handle.

T 1000 PLUS - Optional cable kit

D 1000 Differential relay test module

The differential relay test module D 1000 allows the test of the differential relay curve and also of the harmonic restraint characteristic. The module performances are the followings: . Input: from the test set auxiliary AC voltage output. . Output: 0 to 5 A CA. . Output power: 5 VA. . Dimension: 325 x 290 x 290 mm. . Weight: 7 kg.

Heavy duty transport case

Connection cables
The kit includes cables for any kind of connection.

T 1000 PLUS

SECONDARY INJECTION RELAY TEST SET

Outputs transducer for low level signal relays

The outputs transducer is an option that allows converting the high current and voltage outputs into low voltage signals. The option is made of three components: The Outputs transducer, complete with the interface connector; The connection cable from the transducer to a two BNC connectors and one RJ-45 connector, for the ABB relays REF542PLUS and REF601; The connection cable from the transducer to one RJ-45 connector, for the THYSENSOR series of THYTRONIC relays. The items can be ordered separately: the Output transducer alone, or also one cable or both.
D 1000 Differential relay test module

FT 1000 current filter

This external module removes AC current distortions. It is connected in series to the relay under test, and guarantees a sinusoidal waveform also when testing current relays with reverse time characteristics, or with heavily saturating burdens, that tend to distort the current waveform. . Current input ranges: 0.5 - 2 - 10 - 50 - 100 - 200 A, on terminal bushings. . Maximum power yield: 800 VA. . Filter burden: less than 200 VA at 200 A. The burden is proportional to the range (50 VA at 50 A). . Service: 50 A continuous service; 200 A for 30 s. . Selection of the mains frequency: 50 or 60 Hz, by switch. . Dimensions: 220 x 250 x 310 mm. . Weight: 15 kg.

Output transducer module

SHA 1000 scanning head

SHA 1000 is a scanning head that eases the test of energy meters. It is an universal scanning head because it can be used both with LED impulse electronic meters and Ferraris rotating disk meters; selection is performed via a switch located on the scanning head. In addition to this, a knob allows to adjust the sensitivity of the head. With rotating disk the sensor uses a green light beam that optimizes the recognition of any type of mark. With LED recognition the following specification applies: . Impulse duration: more than 60 us; . With an LED signal having a space ratio 1:2, the frequency must be less than 500 Hz.; . Light wavelength: 500 to 960 nm (red: green and blue ARE NOT detected).

APPLICABLE STANDARDS
The test set conforms to the EEC directives regarding Electromagnetic Compatibility and Low Voltage instruments. A) Electromagnetic Compatibility: Directive no. 2004/108/EC B) Low Voltage Directive: Directive n. 2006/95/EC. Applicable standards, for a class I instrument, pollution degree 2, Installation category II: . CEI EN 61010-1. In particular: . Inputs/outputs protection: IP 2X - CEI 70-1. . Operating temperature: 0 to 50C; storage: -40C to 70C. . Relative humidity: 10 - 80% without condensing.

T 1000 PLUS

ORDERING INFORMATION
CODE 91093 81093 94093 96093 93093 MODULE T 1000 PLUS complete with Software TDMS and standard set of cables - 230V T 1000 PLUS complete with Software TDMS and standard set of cables - 120V TD 1000 PLUS complete with Software TDMS and standard set of cables - 230V TD 1000 PLUS complete with Software TDMS and standard set of cables - 120V TD 1000 PLUS 15 Hz complete with Software TDMS and standard set of cables 230V TD 1000 PLUS 15 Hz complete with Software TDMS and standard set of cables 120V T 1000-E PLUS (500V Aux Voltage outputs) complete with Software TDMS and standard set of cables- 230 V CODE 17093 18093 MODULE Heavy Duty Transport Case Set of additional test cables for models T 1000 PLUS / T 1000-E PLUS / TD 1000 PLUS D 1000 differential relay test module FT 1000 Mains Filter Unit SHA 1000 scanning head Outputs transducer with interface connector and cables Connection cable and RJ-45 connector for ABB relays (REF542PLUS and REF601) Connection cable for THYTRONIC relays (Thysensor series)

40093 16093 43102 13093 11093 12093

95093

92093

T 1000 PLUS / T 1000-E PLUS / TD 1000 PLUS FAMILY - FEATURES COMPARISON TABLE MAIN I AC MAX A
T 1000 Plus 120 V T 1000 Plus 230 V T 1000- E Plus TD 1000 Plus 120 V TD 1000 Plus 230 V TD 1000 Plus 15 Hz 120 V TD 1000 Plus 15 Hz 230 V 160 250 250 160 250 160 250

MAIN V AC MAX V
250 250 500 250 250 250 250

MAIN V DC MAX V
300 300 300 300 300 300 300

AUX V AC MAX V
250 250 500 250 250 250 250

AUX I AC
20 20 20 20

AUX I/V AC POWER @ 15 Hz VA

10 10 10 10 10 25 25

AUX V DC MAX V
240 240 240 240 240 -

ISA Srl Via Prati Bassi, 22 21020 Taino VA - Italy Tel +39 0331 956081 Fax +39 0331 957091 Web site: www.isatest.com E-Mail: isa@isatest.com
8

GB-T1000Plus-12/2011

The document is subject to change without notice. Always refer to our technical specification for more detailed information and as formal contract document.