Professional Documents
Culture Documents
GS - 3246 Service Manual
GS - 3246 Service Manual
Introduction
Genie Europe
Telephone (44) 01636-605030 Fax (44) 01636-611090 http://www.genielift.com E-mail: techpub@genieind.com
Copyright 1997 by Genie Industries First Edition: First Printing, December 1997 Second Printing, April 1999 Third Printing,October 1999
"Genie" is a Registered Trademark of Genie Industries in the USA and many other countries. "GS" is a Trademark of Genie Industries. Printed on recycled paper Printed in U.S.A.
ii
Safety Rules
Danger
Failure to obey the instructions and safety rules in this manual and the Genie GS-2032 & Genie GS-2046 & Genie GS-2646 & Genie GS-3246 Operator's Manual will result in death or serious injury. Many of the hazards identified in the operators manual are also safety hazards when maintenance and repair procedures are performed.
iii
SAFETY RULES
Personal Safety
Any person working on or around a machine must be aware of all known safety hazards. Personal safety and the continued safe operation of the machine should be your top priority.
Be sure to wear protective eye wear and other protective clothing if the situation warrants it. Be aware of potential crushing hazards such as moving parts, free swinging or unsecured components when lifting or placing loads. Always wear approved steel-toed shoes.
Read each procedure thoroughly. This manual and the decals on the machine use signal words to identify the following: Safety alert symbolused to alert personnel to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Redused to indicate the presence of an imminently hazardous situation which, if not avoided, will result in death or serious injury. Orangeused to indicate the presence of a potentially hazardous situation which, if not avoided, could result in death or serious injury. Yellow with safety alert symbol used to indicate the presence of a potentially hazardous situation which, if not avoided, may cause minor or moderate injury. Yellow without safety alert symbolused to indicate the presence of a potentially hazardous situation which, if not avoided, may result in property damage. Greenused to indicate operation or maintenance information.
Workplace Safety
Be sure to keep sparks, flames and lighted tobacco away from flammable and combustible materials like battery gases and engine fuels. Always have an approved fire extinguisher within easy reach.
Be sure that all tools and working areas are properly maintained and ready for use. Keep work surfaces clean and free of debris that could get into machine components and cause damage.
Be sure that your workshop or work area is properly ventilated and well lit.
Be sure any forklift, overhead crane or other lifting or supporting device is fully capable of supporting and stabilizing the weight to be lifted. Use only chains or straps that are in good condition and of ample capacity.
Be sure that fasteners intended for one time use (i.e., cotter pins and self-locking nuts) are not reused. These components may fail if they are used a second time.
Be sure to properly dispose of old oil or other fluids. Use an approved container. Please be environmentally safe.
iv
Theory of Operation
Power Source
The Genie GS-2046 & Genie GS-2646 & Genie GS-3246 machines are powered by four six-volt (225 AH) batteries. The four batteries are wired in series to produce 24 volts. to the default settings in the ECM software.
Machine Controls
The GS-2046 & GS-2646 & GS-3246 machines are equipped with operational controls which are found in two locations: the ground controls, located on the hydraulic tank side of the machine, and the platform controls, located in the platform. All lift and drive functions are available at the platform controls. Only platform up/down functions are available at the ground controls. The ECM uses input from the ground or platform controls to activate the various machine functions. The ECM has predetermined settings for the various machine functions. The joystick is fitted with a 5000 ohm potentiometer. With the joystick in the neutral position, the potentiometer will measure 2730 ohms. These signals are sent to the multiplex card, then down to the ECM to control the voltage supplied to the proportional valve. Two microswitches mounted on the joystick tell the ECM the drive direction desired. A thumb rocker switch on the top of the joystick is used for steering. Mounted on the platform control box lid of machines before serial number 17408 are buttons and a switch that, when activated, sends a signal to the ECM through the multiplex card. On machines after serial number 17407, the platform control box lid has a decal/membrane pad. This is a touch-activated pad incorporating wiring, switches and LEDs that are resistant to the environment. Activating any of the buttons on the
Hydraulic System
All machine functions are performed by the hydraulic system. The hydraulic system is powered by a single-section gear pump. When the pump is activated, it supplies hydraulic fluid under pressure to the function manifold, where the control valves are located. To protect from overpressurization of the hydraulic system, the pump is provided with a pressure relief valve. Activating a machine function is accomplished by actuating or moving a switch and/or control handle, which sends voltage to the ECM. The ECM then sends the signal to the appropriate directional control valve. The directional valve determines which direction the hydraulic fluid will travel. Computer software determines the volume of fluid in relation to the proportional valve input voltage.
Electrical System
Limit switches are found in various locations on the machine. The function of a limit switch is to communicate the operating position of the machine to the ECM (Electronic Control Module). When a change in signal is received from a limit switch, the ECM responds by limiting the drive speed to 0.5 miles per hour (0.8 km/h), according
THEORY OF OPERATION
pad will send a signal to the ECM through the multiplex card. A diagnostic display is located at the battery pack side of the machine to aid in troubleshooting. If the machine malfunctions, a fault code will be shown in the display window. Washing electronic components is not suggested. Instead, use compressed air to remove debris from these components. Component damage hazard. Avoid shock or impact to the ECM. Internal damage may not be visible from the outside.
vi
Table of Contents
Introduction Important Information ..................................................................................................... ii Section One Safety Rules General Safety Rules .................................................................................................... iii Section Two Specifications Machine Specifications, GS-2046 ............................................................................ 2 - 1 Machine Specifications, GS-2646 ............................................................................ 2 - 2 Machine Specifications, GS-3246 ............................................................................ 2 - 3 Performance Specifications, All Models ................................................................... 2 - 4 Hydraulic Specifications, All Models ......................................................................... 2 - 4 Hydraulic Hose and Fitting Torque Specifications .................................................... 2 - 5 Section Three Scheduled Maintenance Inspections Introduction ............................................................................................................... 3 - 1 Table A ..................................................................................................................... 3 - 2 Table B ..................................................................................................................... 3 - 2 Table C ..................................................................................................................... 3 - 3 Table D ..................................................................................................................... 3 - 3 Maintenance Inspection Report ................................................................................ 3 - 4 Section Four Scheduled Maintenance Procedures Introduction ............................................................................................................... 4 - 1 A-1 A-2 A-3 A-4 A-5 Inspect the Operators and Safety Manuals .................................................... 4 - 2 Inspect the Decals and Placards .................................................................... 4 - 2 Inspect for Damage, and Loose or Missing Parts ........................................... 4 - 3 Check the Hydraulic Oil Level ......................................................................... 4 - 4 Check for Hydraulic Leaks .............................................................................. 4 - 4
vii
TABLE OF CONTENTS
Section Four
Scheduled Maintenance Procedures, continued A-6 A-7 A-8 A-9 Test the Platform and Ground Controls .......................................................... 4 - 5 Test the Manual Platform Lowering Operation ............................................... 4 - 6 Test the Tilt Sensor ........................................................................................ 4 - 6 Test the Pothole Guards ................................................................................. 4 - 7
A-10 Test the Lift/Drive Select Switch ..................................................................... 4 - 7 A-11 Perform 30 Day Service .................................................................................. 4 - 8 B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 B-9 Check the Batteries ........................................................................................ 4 - 9 Inspect the Electrical Wiring .......................................................................... 4 - 10 Inspect the Tires and Wheels (including castle nut torque) ............................ 4 - 11 Test the Key Switch ...................................................................................... 4 - 11 Test the Emergency Stop Buttons ................................................................. 4 - 12 Test the Service Horn .................................................................................... 4 - 12 Test the Drive Brakes .................................................................................... 4 - 13 Test the Drive Speed - Stowed Position ........................................................ 4 - 15 Test the Drive Speed - Raised Position ......................................................... 4 - 15
B-10 Perform Hydraulic Oil Analysis ...................................................................... 4 - 16 B-11 Check the Electrical Contactor ...................................................................... 4 - 16 B-12 Replace the Hydraulic Return Filter ............................................................... 4 - 17 C-1 D-1 Check the Module Tray Latch Components ................................................... 4 - 18 Test or Replace the Hydraulic Oil .................................................................. 4 - 19
viii
TABLE OF CONTENTS
Fault Code Chart (Before Serial Number 17408) ..................................................... 5 - 3 Normal Operation Code Chart (Before Serial Number 17408) ................................. 5 - 6 Fault Code Chart (After Serial Number 17407) ........................................................ 5 - 8 1 2 3 4 5 6 7 8 9 10 11 12 13 14 All Functions Will Not Operate ................................................................................. 5 - 9 Pump Motor Will Not Operate ................................................................................ 5 - 12 Pump Motor Will Not Operate After serial number 6900 ........................................................................................ 5 - 14 All Functions Inoperative, Power Unit Starts and Runs (No applicable code) ............................................................................................... 5 - 16 Ground Controls Inoperative, Platform Controls Operate Normally (No applicable code) ............................................................................................... 5 - 17 Platform Controls Inoperative, Ground Controls Operate Normally (No applicable code) ............................................................................................... 5 - 18 Platform Up Function Inoperative ........................................................................... 5 - 20 Platform Down Function Inoperative GS-2046 & GS-2646 Models .................................................................................. 5 - 21 Platform Down Function Inoperative GS-3246 Models .................................................................................................... 5 - 23 Steer Left Function Inoperative .............................................................................. 5 - 25 Steer Right Function Inoperative ............................................................................ 5 - 27 All Drive Functions Inoperative, All Other Functions Operate Normally ................. 5 - 29 Brake Release Function Inoperative ...................................................................... 5 - 31 Drive Forward Function Inoperatmive .................................................................... 5 - 32
ix
TABLE OF CONTENTS
Section Five 15 16 17 18 19 20 21
Troubleshooting Flow Charts and Fault Codes, continued Drive Reverse Function Inoperative ....................................................................... 5 - 33 Machine Will Not Drive At Full Speed ..................................................................... 5 - 34 Machine Drives At Full Speed With Platform Raised ............................................. 5 - 36 Manual Platform Lowering Function Inoperative GS-2046 & GS-2646 (No applicable code) ............................................................ 5 - 37 Manual Platform Lowering Function Inoperative GS-3246 (No applicable code) ............................................................................... 5 - 38 Drive Function Overspeeds While Driving Down an Incline GS-3246 Models (No applicable code) ................................................................... 5 - 39 Drive Function Hesitates While Steering GS-3246 Models (No applicable code) ................................................................... 5 - 40 Schematics Introduction ............................................................................................................... 6 - 1 Electrical Components .............................................................................................. 6 - 2 Module Tray Legend (Before serial number 6901) ................................................... 6 - 4 Module Tray Legend (After serial number 6900) ...................................................... 6 - 5 Electrical Symbols Legend ....................................................................................... 6 - 6 Electrical Schematic (Before serial number 6901) .................................................... 6 - 7 Electrical Schematic (From serial number 6901 to 8931) ......................................... 6 - 9 Electrical Schematic (From serial number 8932 to 17407) ..................................... 6 - 11 Electrical Schematic (After serial number 17407)................................................... 6 - 13 Ground Controls and Level Sensor Box Legend .................................................... 6 - 15 Platform Controls Legend (Before serial number 17408) ....................................... 6 - 16 Platform Controls Legend (After serial number 17407) .......................................... 6 - 17 Hydraulic Symbols Legend ..................................................................................... 6 - 18 Hydraulic Schematic (Before serial number 17482) ............................................... 6 - 19 Hydraulic Schematic (After serial number 17481) .................................................. 6 - 20
Section Six
TABLE OF CONTENTS
Section Seven
Repair Procedures Introduction ............................................................................................................... 7 - 1 Platform Controls 1-1 1-2 1-3 1-4 Joystick Controller .......................................................................................... 7 - 2 Software Configuration ................................................................................... 7 - 3 How to Set the Dip Switch Codes .................................................................. 7 - 4 Toggle Switches ............................................................................................. 7 - 6
Scissor Components 3-1 3-2 3-3 3-4 Scissor Assembly, GS-2046 ......................................................................... 7 - 11 Scissor Assembly, GS-2646 ......................................................................... 7 - 17 Scissor Assembly, GS-3246 ......................................................................... 7 - 25 Lift Cylinder ................................................................................................... 7 - 32
Ground Controls 4-1 4-2 4-3 Manual Platform Lowering Cable, GS-2046 & GS-2646 ............................... 7 - 35 Manual Platfrom Lowering, GS-3246 ............................................................ 7 - 36 Toggle Switches, See 1-2, Toggle Switches ................................................. 7 - 36
Manifolds 6-1 6-2 6-3 6-4 6-5 Function Manifold Components (Before serial number 11501) ..................... 7 - 38 Function Manifold Components (After serial number 11500) ........................ 7 - 40 Valve Adjustments - Function Manifold......................................................... 7 - 42 Valve Adjustments - Lift Relief Valve, GS-3246 ........................................... 7 - 44 Valve Adjustments - Back Pressure Relief Valve ......................................... 7 - 45
xi
Section Seven
Repair Procedures, continued Steering Axle Components 7-1 7-2 7-3 Yoke and Drive Motor ................................................................................... 7 - 46 Steering Cylinder .......................................................................................... 7 - 48 Steering Bellcrank ......................................................................................... 7 - 48
Brake Release Hand Pump Components 9-1 Brake Release Hand Pump .......................................................................... 7 - 50
xii
Section 2 - Specifications
Specifications
Machine Specifications GS-2046
Stowed dimensions Length Length, platform extended Width Models with sliding rails Height, stowed maximun Rails up - ANSI & CSA Height, stowed maximum Rails up - CE Height, stowed maximum Rails lowered Height, stowed maximum Rails removed Height, guard rails - ANSI & CSA Height, guard rails - CE Models with folding rails Height, stowed maximum Height stowed maximum Rails folded Platform height, Stowed maximum Operational dimensions Maximum platform height Maximum platform working height Maximum platform extension Wheelbase Turning radius, outside Turning radius, inside 26 ft 20 ft 39 in 72 7/8 in 91 3/4 in 0 in 7.9 m 6.1 m 99 cm 185.1 cm 233.1 cm 0 cm 861/8 in 643/4 in 423/8 in 219 cm 164 cm 107.6 cm 42 781/2 in 827/8 in 713/4 in 391/4 in 39 in
1 /2
Platform dimensions Length Width 89 in 453/4 in 39 in 1200 lbs 226 cm 116 cm 99 cm 544 kg
96 in 1351/2 in 46 in
4324 lbs 4 in
7/8
Ground clearance Pothole guards deployed Tires and wheels Tire size (solid rubber) Load range Tire contact area Overall tire diameter Wheel diameter Wheel width Castle nut torque Fluid Capacities Hydraulic tank capacity Hydraulic system capacity (including tank)
in
15 x 5 x 11 1/4 in 38.1 x 12.7 x 28.6 cm 2,400 lbs 9 sq in 15 in 111/4 in 5 in 300 ft-lbs 1,089 kg 58 sq cm 38.1 cm 28.6 cm 12.7 cm 406.7 Nm
in
Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice.
2-1
Section 2 - Specifications
SPECIFICATIONS
Platform dimensions Length Width Extension length Maximum load capacity All Models Weight Ground clearance Pothole guards deployed Tires and wheels Tire size (solid rubber) Load range Tire contact area Overall tire diameter Wheel diameter Wheel width Castle nut torque Fluid Capacities Hydraulic tank capacity Hydraulic system capacity (including tank) 51/2 gallons 6 gallons 20.8 liters 22.7 liters 15 x 5 x 11 1/4 in 38.1 x 12.7 x 28.6 cm 2,400 lbs 10 sq in 15 in 11 1/4 in 5 in 300 ft-lbs 1,089 kg 64.5 sq cm 38.1 cm 28.6 cm 12.7 cm 406.7 Nm 4646 lbs 4 in
7/8
in
Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice.
2-2
Section 2 - Specifications
SPECIFICATIONS
Platform dimensions Length Width Extension length Maximum load capacity All Models Weight Ground clearance Pothole guards deployed Tires and wheels Tire size (solid rubber) Load range Tire contact area Overall tire diameter Wheel diameter Wheel width Castle nut torque 15 x 5 x 11 1/4 in 38.1 x 12.7 x 28.6 cm 2,400 lbs 10 sq in 15 in 11 1/4 in 5 in 300 ft-lbs 1,089 kg 64.5 sq cm 38.1 cm 28.6 cm 12.7 cm 406.7 Nm 5564 lbs 4 in
7/8
in
Fluid Capacities before serial number 21920 Hydraulic tank capacity Hydraulic system capacity (including tank) 51/2 gallons 6 gallons 20.8 liters 22.7 liters
Fluid Capacities after Serial Number 21919 Hydraulic oil type Hydrailic tank capacity Hydraulic system (including tank) Dexron equivalent 7 gallons 26.5 liters 7 gallons 26.5 liters
Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice.
2-3
Section 2 - Specifications
SPECIFICATIONS
4 gallons per minute 15.1 liters per minute (2500 psi/172 bar) 10 micron with 25 psi (1.7 bar) bypass
Hydraulic tank return line filter Function manifold 28 to 32 seconds 26 to 30 seconds System relief valve pressure (GS-2046 & GS-2646 models) Drive relief valve pressure (GS-3246 models) Lift relief valve pressure (GS-3246 models) Steer relief valve pressure 55 to 59 seconds 38 to 40 seconds
Platform up Platform down GS-2646 Platform up Platform down GS-3246 Platform up Platform down
28 to 32 seconds 26 to 30 seconds
2-4
Section 2 - Specifications
SPECIFICATIONS
Torque Procedure
1 Replace the O-ring. The O-ring must be replaced anytime the seal has been broken. The O-ring cannot be re-used if the fitting or hose end has been tightened beyond finger tight. The O-rings used in the Parker Seal Lok fittings and hose ends are a custom-size O-ring. They are not a standard SAE size Oring. They are available in the Oring field service kit (Genie pn. 49612). 2 Lubricate the O-ring before installation. 3 Be sure that the face seal O-ring is seated and retained properly. 4 Position the tube and nut squarely on the face seal end of the fitting and tighten the nut finger tight. 5 Tighten the nut or fitting to the appropriate torque per given size as shown in the table above. 6 Operate all machine functions and inspect the hoses and fittings and related components to be sure that there are no leaks. 2-5
Section 2 - Specifications
2-6
There are four types of maintenance inspections that must be performed according to a schedule daily, quarterly, annual and every two years. To account for repeated procedures, the Maintenance Tables and the Maintenance Inspection Report have been divided into four subsectionsA, B, C, D. Use the following chart to determine which group(s) of procedures are required to perform a scheduled inspection.
Inspection Daily Quarterly Annual Two year Table or Checklist A A+B A+B+C A+B+C+D
Maintenance Tables The maintenance tables contained in this section provide summary information on the specific physical requirements for each inspection. Complete step-by-step instructions for each scheduled maintenance procedure are provided in section 4, Scheduled Maintenance Procedures. Maintenance Inspection Report The maintenance inspection report contains checklists for each type of scheduled inspection. Make copies of the Maintenance Inspection Report to use for each inspection. Store completed forms for three years.
3-1
Maintenance Tables
Table A
A-1 Inspect the Operator's and Safety Manuals
Tools are required New parts required Dealer service suggested
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
Table B
B-1 Check the Batteries
B-2
B-3
Inspect the Tires and Wheels (including castle nut torque) Test the Key Switch
B-4
3-2
MAINTENANCE TABLES
Table B,
B-5
continued
B-6
B-7
B-8
B-9
B-10
Perform Hydraulic Oil Analysis See D-1 Test or Replace the Hydraulic Oil Check the Electrical Contactor
B-11
Every 250 hours, perform the following engine maintenance procedure. B-12 Replace the Hydraulic Return Filter
Table C
C-1 Check the Module Tray latch Components
Table D
D-1 Test or Replace the Hydraulic Oil
3-3
Y N R
3-4
Symbols Legend Safety alert symbolused to alert personnel to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Redused to indicate the presence of an imminently hazardous situation which, if not avoided, will result in death or serious injury. Orangeused to indicate the presence of a potentially hazardous situation which, if not avoided, could result in death or serious injury. Yellow with safety alert symbol used to indicate the presence of a potentially hazardous situation which, if not avoided, may cause minor or moderate injury. Yellow without safety alert symbolused to indicate the presence of a potentially hazardous situation which, if not avoided, may result in property damage. Greenused to indicate operation or maintenance information. Indicates that a specific result is expected after performing a series of steps.
4-1
Table A Procedures
A-1 Inspect the Operators and Safety Manuals
Maintaining the operators and safety manuals in good condition is essential to safe machine operation. Manuals are included with each machine and should be stored in the container provided in the platform. An illegible or missing manual will not provide safety and operational information necessary for a safe operating condition. 1 Check to be sure the storage container is present and in good condition. 2 Check to make sure that the operators, responsibilities and safety manuals are present and complete in the storage container in the platform. 3 Examine the pages of each manual to be sure that they are legible and in good condition. 4 Always return the manuals to the storage container after use. Contact your authorized Genie distributor or Genie Industries if replacement manuals are needed.
4-2
TABLE A
PROCEDURES
Check the entire machine for: Cracks in welds or structural components Dents or damage to machine Be sure that all structural and other critical components are present and all associated fasteners and pins are in place and properly tightened Side rails installed and bolts are fastened Be sure that the chassis trays are in place, latched and properly connected
4-3
TABLE A
PROCEDURES
Hydraulic system (including tank) Hydraulic Oil Specifications GS-3246 After Serial Number 21919 Hydraulic oil type Hydrailic tank capacity
4-4
TABLE A
PROCEDURES
7 Press and hold the function enable switch on the control handle. Result: The green power light should come on, OR the light below the lift selector button should come on. 8 Slowly move the control handle in the direction indicated by the blue arrow. Result: The platform should raise. The pothole guards should deploy. 9 Release the control handle. Result: The platform should stop raising. 10 Press and hold the function enable switch. Slowly move the control handle in the direction indicated by the yellow arrow. Result: The platform should lower. The descent alarm should sound while the platform is lowering. CE models: When lowering the platform, the platform should stop when it is 6 feet (1.8 m) from the ground. Be sure the area below the platform is clear of personnel and obstructions before continuing. To continue lowering, release the control handle, wait 4-6 seconds, then move the control handle again. 11 Push in the Emergency Stop button to the position. Result: No function should operate. The machine should stop. As a safety feature, selecting and operating the ground controls will override the platform controls, except the Emergency Stop button.
OFF
4-5
TABLE A
PROCEDURES
4-6
TABLE A
PROCEDURES
A-10 Test the Lift/Drive Select Switch (before serial number 17408)
A properly functioning Lift/Drive Select Switch is essential for safe machine operation. An improperly operating Lift/Drive Select Switch will fail to activate the appropriate platform control which may result in a hazardous situation. 1 Turn the key switch to platform control and pull out the Emergency Stop button to the ON position at both the platform and ground controls. 2 Move the lift/drive select switch to the LIFT position. 3 Press and hold the function enable switch. Result: The green power light should come on. 4 Slowly move the control handle off center. Result: The platform should raise or lower. 5 Move the lift/drive select switch to the position.
DRIVE
6 Press and hold the function enable switch. Result: The green power light should come on. 7 Slowly move the control handle off center. Result: The drive and steer functions should operate.
4-7
TABLE A
PROCEDURES
4-8
Table B Procedures
B-1 Check the Batteries
Proper battery condition is essential to good machine performance and operational safety. Improper fluid levels or damaged cables and connections can result in component damage and hazardous conditions. Bodily injury hazard. Batteries contain acid. Avoid spilling or contacting battery acid. Neutralize battery acid spills with baking soda and water. Electrocution hazard. Contact with hot or live circuits may result in death or serious injury. Remove all rings, watches and other jewelry. Perform this test after fully charging the batteries. 1 Put on protective clothing and eye wear. 2 Disconnect the battery pack from the machine. 3 Be sure that the battery cable connections are free of corrosion. 4 Be sure that the battery hold downs and cable connections are tight. 5 Remove the battery vent caps and check the specific gravity of each battery cell with a hydrometer. Result: If any battery cell displays a specific gravity of less than 1.098, the battery must be replaced. 6 Check the battery acid level of each battery. If needed, replenish with distilled water to the bottom of the battery fill tube. Do not overfill. 7 Install the battery vent caps. 8 Check each battery pack and verify that the batteries are wired correctly.
4-9
TABLE B
PROCEDURES
6 Inspect the center chassis area and scissor arms for burnt, chafed and pinched cables. 7 Inspect the following areas for burnt, chafed, corroded, pinched and loose wires: ECM to platform controls Power to platform wiring
8 Raise the platform and return the safety arm to the stowed position. 9 Lower the platform to the stowed position and turn the machine off.
4 - 10
TABLE B
PROCEDURES
B-3 Inspect the Tires and Wheels (including castle nut torque)
Maintaining the tires and wheels in good condition is essential to safe operation and good performance. Tire and/or wheel failure could result in a machine tip-over. Component damage may also result if problems are not discovered and repaired in a timely fashion. 1 Check the tire surface and sidewalls for cuts, cracks or unusual wear. 2 Check each wheel for damage, bends and cracks. 3 Remove the cotter pin and check each castle nut for proper torque. 4 Install a new cotter pin. Always replace the cotter pin with a new one when removing the castle nut or when checking the torque of the castle nut.
Tires and wheels Castle nut torque, dry Castle nut torque, lubricated 300 ft-lbs 225 ft-lbs 405 Nm 305 Nm
4 - 11
TABLE B
PROCEDURES
4 - 12
TABLE
PROCEDURES
7 Measure the distance between the test line and your machine reference point.
Braking: paved surface Stopping distance 2 ft 0.6 m
Result: The machine stops within the specified braking distance. No action required. Result: The machine does not stop within the specified braking distance. Proceed to step 8 and determine if the machine is equipped with a dynamic braking valve. The brakes must be able to hold the machine on any slope it is able to climb. 8 Disconnect the battery pack from the machine. Electrocution hazard. Contact with electrically charged circuits could result in death or serious injury. Remove all rings, watches and other jewelry. 9 Locate the drive forward/reverse valve on the function manifold. Refer to Illustrations 1
a
a drive forward/reserve valve
4 - 13
TABLE B
PROCEDURES
10 Tag the forward and the reverse valve coils. Remove the coils from the valve. The forward valve coil has white and brown wires attached. The reverse valve coil has white/black and brown wires attached. For reassembly, it will be helpful to leave the wire harness attached to the valve coils. 11 Remove the drive forward/reverse valve from the function manifold. Cap the open port of the manifold. 12 Carefully inspect the hex portion of the valve for an identification stamp. Result: SV10-4727 is stamped on the hex portion of the drive forward/reverse valve. This indicates the machine is equipped with a dynamic brake valve. Proceed to step 13. Result: SV10-4727 is not stamped on the hex portion of the drive forward/reverse valve. This indicates the machine is not equipped with a dynamic brake valve. Proceed to step 18. 13 Install the drive forward/reverse valve removed in step 11 into the function manifold and securely tighten. Torque to 25 ft-lbs / 34 Nm. 14 In order, install the reverse valve coil (with white/black and brown wires), spacer washer and the forward valve coil (with white and brown wires) onto the valve. For the machine to function correctly, the reverse valve coil must be closest to the manifold.
15 Install the coil nut onto the valve and tighten. Torque to 60 in-lbs / 7 Nm. 16 Connect the battery pack to the machine. 7 Replace the brakes and repeat this procedure beginning with step 1. Refer to Repair Procedure 8-1, How to Remove a Drive Brake. 18 Contact the Genie Industries Service Parts Department and order kit part number 105457. 19 Install the new valve received in the kit and mark the new valve with a white paint pen to identify new valve installation. 20 Repeat this procedure beginning with step 1. If the machine fails to stop within the specified stopping distance after installing new brakes, please contact the Genie Industries Scissors Service Department, 1-800-536-1800 Ext. 8710.
4 - 14
TABLE B PROCEDURES
4 - 15
TABLE B PROCEDURES
4 - 16
TABLE B PROCEDURES
4 - 17
Table C Procedure
C-1 Check the Module Tray Latch Components
Maintaining the module tray latch components in good condition is essential to good performance and service life. Failure to detect worn out latch components may result in module trays opening unexpectedly, creating an unsafe operating condition. Perform this procedure with the platform in the stowed position. 1 Lubricate each module tray latch. Using light oil, apply a few drops to the side of the latch pin. 2 Inspect each module tray latch pad (if equipped). Replace any worn pad before the latch will fail to securely hold the module tray closed.
4 - 18
Table D Procedure
D-1 Test or Replace the Hydraulic Oil
Replacement or testing of the hydraulic oil is essential for good machine performance and service life. Dirty oil and suction strainer may cause the machine to perform poorly and continued use may cause component damage. Extremely dirty conditions may require oil changes to be performed more often. This machine uses Dexron equivalent hydraulic oil. Before replacing the hydraulic oil, the oil may be tested by an oil distributor for specific levels of contamination to verify that changing the oil is necessary. If the hydraulic oil is not replaced at the two year inspection, test the oil quarterly. Replace the oil when it fails the test. Perform this procedure with the platform in the stowed position. 1 Disconnect the battery pack from the machine. 2 Open the power unit module tray and place a drain pan or other suitable container under the hydraulic tank. 3 Remove the drain plug from the hydraulic tank. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 4 Completely drain the tank into a suitable container. See capacity specifications listed to the right. 5 Tag, disconnect and plug the suction hose and return hose from the hydraulic tank. 6 Remove the hydraulic tank from the machine. 7 Remove the suction strainer and clean it using a mild solvent. 8 Clean the inside of the hydraulic tank using a mild solvent. 9 Install the suction strainer using thread sealer on the threads. 10 Install the drain plug using thread sealer on the threads. 11 Install the hydraulic tank. 12 Fill the tank with hydraulic oil until the fluid is within the FULL and ADD marks on the oil level indicator decal. Do not overfill.
4 - 19
TABLE D PROCEDURES
13 Clean up any oil that may have spilled. Properly dispose of the oil. 14 Operate all machine functions through a full cycle and check for leaks.
Hydraulic Oil Specifications Before Serial Number 21920 Hydraulic oil type Hydraulic tank capacity Dexron equivalent 5.5 gallons 20.8 liters 6 gallons 22.7 liters
Hydraulic system (including tank) Hydraulic Oil Specifications After Serial Number 21919 Hydraulic oil type Hydrailic tank capacity
4 - 20
Be sure that all necessary tools and test equipment are available and ready for use. Read each appropriate flow chart thoroughly. Attempting shortcuts may produce hazardous conditions. Be aware of the following hazards and follow generally accepted safe workshop practices. Crushing hazard. When testing or replacing any hydraulic component, always support the structure and secure it from movement. Electrocution hazard. Contact with electrically charged circuits may result in death or serious injury. Remove all rings, watches and other jewelry. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. Perform all troubleshooting on a firm level surface. Two persons will be required to safely perform some troubleshooting procedures.
5-1
Malfunction discovered
Identify symptoms
Troubleshoot
Return to service
problem solved
Perform repair
5-2
Fault Code
Problem
Possible Causes
Solution
00
Alarm sounds continuously. Error indicator light on at the platform controls when function enable switch is engaged. Machine will not drive. Machine is not level. Alarm sounds continuously. Error indicator light on at the platform controls when function enable switch is engaged. Machine will not drive. Machine is level. Pothole guard may be blocked or pothole limit switches may not be activating or there is a bad wire connection.
Reset the ECM. If problem remains, replace the ECM. Remove obstruction to pothole guard OR check pothole limit switch wiring for open connections OR check pothole limit switch for proper adjustment and activation. Remove obstruction to pothole guard OR check pothole limit switch wiring for open connections OR check pothole limit switch for proper adjustment and activation. Release the function enable switch OR check the switch for continuity in the joystick controller box (see Repair Section). Replace joystick controller box main circuit board OR replace the coil cord. Replace joystick controller box main circuit board.
18
19
Pothole guard may be blocked or pothole limit switches may not be activating or there is a bad wire connection.
33 34 35
Machine will not operate. Error Joystick initialization OK but indicator light on at the platform function enable switch is tied controls. down. Machine unit will not operate. Error indicator light on at the platform controls. Machine unit will not operate. Error indicator light on at the platform controls.
ECM does not recognize the platform controls. ECM does not recognize the platform controls.
51
Only the platform down function operates no other No power output from ECM to functions operate. Error indicator light on at the platform the motor contactor. controls when the function enable switch is engaged.
Check wiring and terminal at motor contactor ckt A9-Curtis terminal 3 OR check wiring and terminal at control ECM pin A9, ckt A9-Curtis terminal 3.
Notes
5-3
Section 5 - Troubleshooting Flow Charts FAULT CODE CHART (BEFORE SERIAL NUMBER 17408)
Fault Code
Problem
Possible Causes
Solution
52
Machine will not drive forward. Pump motor starts. Error No power output from ECM to indicator light on at the platform the drive forward coil. controls when the function enable switch is engaged. Machine will not drive in reverse. Pump motor starts. Error indicator light on at the platform controls when the function enable switch is engaged.
Check wiring and terminal at the forward coil, ckt C6Forward coil OR check wiring and terminal at control ECM pin C6, ckt C6 Forward coil.
53
Check wiring and terminal at the reverse coil, ckt A7No power output from ECM to Reverse coil OR check wiring the drive reverse coil. and terminal at ECM pin A7, ckt A7 Reverse coil. Check wiring and terminal at the platform up coil, ckt A6-Up coil OR check wiring and terminal at ECM pin A6, ckt A6 Up coil.
54
Platform will not raise. Pump motor starts. Error indicator No power output from ECM to light on at the platform controls the platform up coil. when the function enable switch is engaged.
55
Check wiring and terminal at Platform will not lower. Error the platform lowering coil, ckt indicator light on at the platform No power output from ECM to B6-Down coil OR check wiring controls when the function the platform lowering coil. and terminal at ECM pin B6, enable switch is engaged. ckt B6 Down coil. Machine will not steer right. Pump motor starts. Error No power output from ECM to indicator light on at the platform steer right coil. controls when the function enable switch is engaged. Machine will not steer left. Pump motor starts. Error No power output from ECM to indicator light on at the platform steer left coil. controls when the function enable switch is engaged. Check wiring and terminal at the steer right coil, ckt C7 Right coil OR check wiring and terminal at ECM pin C7, C7 Right coil. Check wiring and terminal at the steer left coil, ckt B7 Left coil OR check wiring and terminal at ECM pin B7, B7 Left coil.
56
57
58
Check wiring and terminal at the orifice coil, ckt C9 orifice No power output from ECM to coil OR check wiring and the brake orifice coil. terminal at ECM pin C9, C9 orifice coil OR replace Coil.
Notes
Continued on next page
5-4
Section 5 - Troubleshooting Flow Charts FAULT CODE CHART (BEFORE SERIAL NUMBER 17408)
Fault Code
Problem
Possible Causes
Solution
60 63 88 no code available
Machine will not operate. Error Lift/drive switch is turned "off" indicator light on at the platform or in a neutral position. controls. Machine will not operate. Flashing green LED at the platform controls.
Lift/drive switch turned from lift Release function enable switch to drive or drive to lift while the and move lift/drive switch to function enable switch is either lift or drive. engaged. Replace ECM.
Machine will not operate. ECM EPROM not programmed. cannot be reset.
Release function enable switch OR check the function enable Function enable switch held for microswitch for continuity in more than 10 seconds without the joystick controller box. activating any function. Reset controller and check for fault code 33 at power up.
no code available
Machine drive speed reduces to off limit drive speed OR platform raises slowly. Red flashing LED at the platform controls while function enable switch is activated.
Low Voltage Cut Back (LVCB) is activated because battery Charge batteries. supply voltage is 18.5V DC or less.
Notes
5-5
20 flashing
21 flashing
Normal operation
22 flashing
To clear this code, be sure joystick is properly connected or pull the platform Emergency Stop button out to the on position.
23 flashing
24 flashing
To clear this code, be sure joystick is properly connected or pull the platform Emergency Stop button out to the on position.
25 flashing
31 flashing
Normal operation.
32 flashing
To clear this code, be sure joystick is properly connected or pull the platform Emergency Stop button out to the on position.
36 flashing
Up function selected Note: if joystick controller is returned to center position before function enable button is released, code 31 flashing will appear. If function enable button is released first, code 36 flashing will remain until another function is selected. Down function selected Note: if joystick controller is returned to center position before function enable button is released, code 31 flashing will appear. If function enable button is released first, code 37 flashing will remain until another function is selected. Drive in blue direction function selected Note: if joystick controller is returned to center position before function enable button is released, code 31 flashing will appear. If function enable button is released first, code 38 flashing will remain until another function is selected. Drive in yellow direction function selected Note: if joystick controller is returned to center position before function enable button is released, code 31 flashing will appear. If function enable button is released first, code 39 flashing will remain until another function is selected. Horn is being pressed Note: Horn will operate without code 40 flashing if function enable switch is not pressed in.
37 flashing
38 flashing
39 flashing
40 flashing
5-6
5-7
Fault Code
Problem
Possible Causes
Solution
01 02 03 12 18 42 43 45 46 47 52 53 54 55 56 57 58 68
Normal operation Machine will not operate. ECM EPROM not programmed cannot be reset. Platform ECM error Defective control cable OR platfrom controls Replace ECM Troubleshoot cable OR platform controls Correct DIP switch settings Troubleshoot up/down switch Troubleshoot pothole switch OR remove obstruction. Troubleshoot steer left microswitch Troubleshoot steer right microswitch Troubleshoot lift enable switch Troubleshoot drive enable switch Verify potentiometer setting Troubleshoot coil OR inspect wire connection Troubleshoot coil OR inspect wire connection Troubleshoot coil OR inspect wire connection Troubleshoot coil OR inspect wire connection Troubleshoot coil OR inspect wire connection Troubleshoot coil OR inspect wire connection Troubleshoot coil OR inspect wire connection Charge batteries
Undefined platform DIP switch DIP switch settings incorrect settings Chassis up/down switch closed Malfunctioningup/down switch at start up Malfunctioning pothole switch Pothole guard failure OR obstruction in pothole guard linkage Platform left turn switch closed Malfunctioning steer left at start up microswitch Platform right turn switch Malfunctioning steer right closed at start up microswitch Platform lift enable switch Malfunctioning lift enable closed at start up switch Platform drive enable switch Malfunctioning drive enable closed at start up switch Platform joystick off neutral at Joystick potentiometer not start up centered Malfunctioning coil OR wire Forward coil error disconnected from coil Malfunctioning coil OR wire Reverse coil error disconnected from coil Malfunctioning coil OR wire Up coil error disconnected from coil Malfunctioning coil OR wire Down coil error disconnected from coil Malfunctioning coil OR wire Right coil error disconnected from coil Malfunctioning coil OR wire Left coil error disconnected from coil Malfunctioning coil OR wire Brake coil error disconnected from coil Low Voltage Batteries discharged
5-8
Chart 1
All Functions Will Not Operate
If the Error Indicator light is on at the platform controls, please refer to the specific chart that relates to the error code that is displayed on the ECM. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged. Be sure both Emergency Stop buttons are pulled out to the ON position.
Turn keyswitch to the ground control and visually inspect the diagnostic display on the ECM. Is the display blank or does it display a fault code? displays a fault code Refer to the fault code chart to find what chart is associated with your fault code OR consult Genie Industries service department.
display is blank Check voltage on input side of 275A fuse F2 inside battery module tray. less than Charge batteries OR 24V check battery condition and replace bad batteries OR check for short circuits OR check battery cables OR check for open in negative battery cable from batteries to ground point 24V or more on module tray.
Check voltage on output side of 275A fuse F1 inside the battery module tray. 24V
0V
Check continuity from B- no terminal on curtis motor continuity controller to the negative battery cable at the Anderson plug. full continuity Models before serial number 6901: Check the voltage on the input side of the motor contactor K1. Models after serial number 6900: Check the voltage at the B+ terminal on the motor controller. 24V
Repair open in negative battery cable from Bterminal on curtis motor controller to Anderson plug.
0V
Models before serial number 6901: Repair open in 24V supply cable from 275A fuse F1 to the Anderson plug OR repair open in 24V supply cable from Anderson plug to motor contactor K1. Models after serial number 6900: Repair open in 24V supply cable from 275A fuse F1 to Anderson plug OR repair open in 24V supply cable from Anderson plug to the B+ terminal on the motor controller.
5-9
CHART 1
0V
24V
Models before serial number 6901: Repair open in white wire from the input side of the motor contactor to the input side of the 7A circuit breaker (24f-ckt brkr to relay). Models after serial number 6900: Repair open in white wire from the Anderson connector to the input side of the 7A circuit breaker.
Check voltage at white wire at input side of Emergency Stop button S2. 24V Check voltage at input side of each contact at the key switch S2.
0V
Repair open in white wire from output side of 7A circuit breaker OR reset or replace 7A circuit breaker.
0V
24V
Repair open in white wire from Emergency Stop button to key switch OR repair open in white wire jumper to each contact OR replace contact on Emergency Stop button OR replace Emergency Stop button.
Turn key switch to ground control position and check output side of contact.
0V
Check cam on key switch. good Replace contact OR refer to Ground Controls Inoperative, Chart 6 OR consult Genie Industries Service Department.
bad
24V
5 - 10
CHART 1
Turn key switch to platform control position and check output side of each contact.
0V
Check cam on key switch. good Replace bad microswitch OR refer to Platform Controls Inoperative, Chart 5 OR consult Genie Industries Service Department.
24V
Refer to Chart 2, Pump Motor Will Not Operate OR repair open in white wire (C2 estop chassis) OR consult Genie Industries Service Department.
5 - 11
Chart 2
Pump Motor Will Not Operatebefore serial number 6901
Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
Activate lift function from the ground controls and check voltage at positive terminal on pump motor. 24V or more Check voltage on B+ terminal on motor controller. 24V no Check continuity on continuity Replace ground cable ground cable from pump on lift pump motor. motor to M- terminal on motor controller. continuity Check continuity from B- no continuity terminal on motor controller to the negative battery cable at the Anderson plug (AP1). continuity Activate lift function and check voltage at terminal 1 on motor controller. less than 24V 24V Activate the lift function and check voltage at terminal 3 on the motor controller. Repair open in white wire (A9-curtis terminal 3) from ECM to the motor controller OR replace the ECM OR consult Genie Industries Service Department. less than 24V Repair open in white wire (26H) from the motor controller relay coil (K1) to the motor controller. Replace negative cable from B- terminal on motor controller to the Anderson plug. less than 24V Replace positive battery cable from pump to B+ terminal on motor controller.
0V
5V
Activate the lift function and check voltage at Mterminal on the motor controller. 0V Replace pump motor OR consult Genie Industries Service Department. Continued on the next page.
24V
5 - 12
CHART 2
Activate the lift function and check voltage on the output side of K1.
24V or more
Replace positive cable from K1 to the motor controller OR replace positive cable from the motor controller to the pump motor.
Activate the lift function and check voltage on the input side of K1.
Activate the lift function and check voltage on the white wire on the coil of K1. 24V Check continuity on the brn ground wire on the coil of K1 to the ground point on the chassis.
0V
Repair open in wht wire (A8-motor) from ECM to K1 OR replace ECM OR conult Genie Industries Service Department.
continuity
0V
no continuity Repair open in brown ground wire from K1 to the ground point on chassis.
Check voltage on the output side of the 275A fuse (F1). 24V Replace positive battery cables from output side of 275A fuse to the Anderson plug OR replace positive battery cables from Anderson plug to K1 OR consult Genie Industries Service Department.
0V
Replace 275A fuse (F1) OR replace positive cable from 275A fuse to the batteries OR consult Genie Industries Service Department.
5 - 13
Chart 3
Pump Motor Will Not Operate after serial number 6900
Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
Activate the lift function from the ground controls and check voltage at positive terminal on pump motor. 24V or more Check voltage on B+ terminal on the motor controller. 24V no Check continuity on ground cable from pump continuity Replace ground cable motor to M- terminal on on lift pump motor. the motor controller. continuity Check continuity from B- no continuity terminal on the motor controller to the negative battery cable at the Anderson plug (AP1). continuity Activate the lift function and check voltage at terminal 1 on the motor controller. 24V less than 24V Activate the lift function and check voltage at terminal 3 on the motor controller. 0V Repair open in white wire (A9-motor controller terminal 3) from ECM to the potentiometer to the motor controller OR replace the potentiometer OR replace the ECM OR consult Genie Industries Service Department. less than 24V Repair open in white wire (A8-Motor) from the ECM to terminal 1 on the motor controller. Replace negative cable from B- terminal on the motor controller to the Anderson plug. less than 24V Replace positive battery cable from pump to B+ terminal on the motor controller.
5V
Activate the lift function and check voltage at Mterminal on motor controller. 0V Replace pump motor OR consult Genie Industries Service Department.
24V
5 - 14
CHART 3
Check voltage on the output side of the 275A fuse (F1). 24V Replace positive battery cables from output side of 275A fuse to Anderson plug OR replace positive battery cables from Anderson plug to the B+ terminal on the motor controller OR consult Genie Industries Service Department.
0V
Replace 275A fuse OR replace positive cable from 275A fuse to the batteries OR consult Genie Industries Service Department.
5 - 15
Chart 4
All Functions Inoperative, Power Unit Starts and Runs
Check hydraulic fluid level. OK Activate each machine function. Are all functions inoperative and the power unit still starts and runs? yes Connect a 0 to 5000 psi (345 bar) pressure gauge to the test port on the function manifold. Chock both sides of the drive wheels at the steer end of the machine. Turn the keyswitch to platform control and pull out the Emergency Stop buttons out to the ON position at both the ground and platform controls. Activate the drive forward function and check the pressure. less than 3000 psi Check for a positive connection between electric motor and pump by removing pump from motor, but leave all hoses connected. Visually check coupling connection. good Test hydraulic pump. See Repair section. good Consult Genie Industries Service Department. no good Replace the pump. no good Replace pump coupling OR replace pump OR replace motor. Re-adjust the system relief valve (GS-2046 & 2646 models) or the drive relief valve (Gs3246 models) OR valve(s) may be stuck open or closed OR function manifold may have an internal defect. Consult Genie Industries Service Department. no Refer to the specific chart that relates to the inoperative function(s). low Fill with Dexron II equivalent hydraulic fluid.
If the Error Indicator light is on at the platform controls, please refer to the specific chart that relates to the error code that is displayed on the ECM. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
5 - 16
Chart 5
Ground Controls Inoperative, Platform Controls Operate Normally
If the Error Indicator light is on at the platform controls, please refer to the specific chart that relates to the error code that is displayed on the ECM. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
Turn the keyswitch to ground control and make sure both Emergency Stop buttons are pulled out to the ON positon at both the ground and platform controls. Check voltage on the contact at the input side of the keyswitch at the ground controls (S2). 24V or more Check voltage at output side of contact. 0V Check if key switch internal cam is activating ground control contact. no 24V Replace key switch. yes Replace key switch contact for ground controls. 0V Repair open in white wire jumper from platform control contact to the ground control microswitch at the keyswitch (S2).
Check voltage at the center terminal of the platform up/down toggle switch (S3) at the ground controls.
0V
Repair open in white wire jumper from keyswitch to center terminal on toggle switch.
24V
Test or replace platform up/down toggle switch S3 (See Repair Section) OR repair open in white wire from toggle switch to ECM (B12-up switch) OR repair open in white wire from toggle switch to ECM (A12-down switch) OR consult Genie Industries Service Department.
5 - 17
Chart 6
Platform Controls Inoperative, Ground Controls Operate Normally
If the Error Indicator light is on at the platform controls, please refer to the specific chart that relates to the error code that is displayed on the ECM. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
Turn keyswitch to the ground control and visually inspect the diagnostic display on the ECM. Does it display a fault code? no Turn keyswitch to platform control and make sure both Emergency Stop buttons are pulled out to the ON positon at both the ground and platform controls. Check voltage at the input side of the platform controls contact on the keyswitch at the ground controls (S2). 24V or more Check voltage at output side of contact. 0V Check if key switch internal cam is activating platform control contact. no 24V Replace key switch. yes Replace key switch contact for platform controls. Repair open in white wire jumper from Emergency Stop contact to the platform control contact at the keyswitch (S2). yes Refer to the fault code chart to find what chart is associated with your fault code OR consult Genie Industries service department.
0V
Check voltage at terminal A11 at the ECM. 24V Check voltage at terminal B2 at the ECM.
0V
Repair open in white wire (A11-key switch) from keyswitch to A11 at ECM.
0V
Replace ECM.
24V
5 - 18
CHART 6
Turn keyswitch to platform controls and check voltage at terminal 4 on the main circuit board at the platform controls. 24V Check voltage at the input side of the Emergency Stop button at the platform controls. 24V Check voltage at output side of platform Emergency Stop button. 24V Check voltage at terminal 5 on the main circuit board at the platform controls. 24V Check voltage at terminal A4 at the ECM.
0V
Replace coil cord assembly from the ECM to the platform controls.
0V
Repair open in wire from terminal 4 on main circuit board to input side of Emergency Stop button.
0V
0V
Repair open in wire from terminal 5 on main circuit board to output side of Emergency Stop button.
0V
24V
Replace coil cord from ECM to platform controls OR replace joystick controller OR replace main circuit board OR replace ECM OR consult Genie Industries Service Department.
5 - 19
Chart 7
Platform Up Function Inoperative
Be sure all other functions operate normally. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
light is not on With key switch in platform position and both Emergency Stop buttons pulled out to the on position and the lift/ drive selector switch in the lift position, activate the controller in the up direction and check to see if the error indicator light at the platform controls is on. light is on Disconnect the wires from the platform up directional valve coil on function manifold (item H) and check the resistance of the valve coil. See Repair Section. 18-20 ohms Check continuity from the brown ground wire at the valve coil to ground. continuity Repair open in white wire (A6-lift coil) from the platform up directional valve coil to the ECM (see Repair Section) OR replace ECM OR consult Genie Industries Service Department. no Repair open in brown continuity ground wire circuit from the platform up directional valve coil (item H) to ground. 0 or infinite ohms Replace platform up directional valve coil (item H).
Install a 0 to 4000 PSI pressure gauge at the quick disconnect coupling on the function manifold and activate the platform up function.
less than 3000 PSI Adjust relief valve (see Repair Section) OR repair or replace platform lift cylinder(s) OR platform lowering valve(s) may be stuck open OR function manifold could have an internal defect. Consult Genie Industries Service Department.
Check for mechanical restrictions keeping platform up function from moving OR repair or replace the platform up directional valve cartridge (item H) OR repair or replace platform lift cylinder(s) OR consult Genie Industries Service Department.
5 - 20
Chart 8
Platform Down Function Inoperative, GS-2046 & GS-2646
Be sure all other functions operate normally. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
With key switch in platform position and the platform raised slightly and both Emergency Stop buttons pulled out to the on position at both the ground and platform controls and the lift/drive switch in the lift position, activate the controller in the down direction and check to see if the error indicator light is on. With the platform raised and the safety arm installed, label and disconnect the wires from the coil on the platform lowering valve (item Q) at the platform lift cylinder and check the resistance. See Repair Section. 0 or infinite ohms Replace platform lowering valve coil (item Q).
light is on
23 to 25 ohms Check continuity from the brown ground wire at the valve coil to ground. continuity With the platform raised and the safety arm removed, pull the manual platform lowering handle at the ground controls. platform does not lower Repair open in white wire (B6-down coil) from the platform lowering valve coil (item Q) to the ECM OR replace the ECM OR repair or replace the platform lowering valve cartridge (item Q) OR consult Genie Industries Service Department. no Repair open in brown continuity ground wire circuit from the platform lowering valve coil (item H) to ground.
platform lowers
light is not on
Check for mechanical restrictions keeping platform from lowering OR repair or replace the platform lowering valve cartridge (item Q) OR 0.059" orifice inside the cylinder is plugged OR repair or replace lift cylinder OR consult Genie Industries Service Department.
5 - 21
CHART 8
Label and disconnect the wires from the lift/ drive toggle switch (S7) at the platform controls and troublshoot toggle switch (see Repair Section). good Check for mechanical restrictions keeping platform from lowering OR repair or replace the platform lowering valve cartridge (item Q) OR 0.059" orifice inside the cylinder is plugged OR repair or replace lift cylinder OR replace platform controls OR replace ECM OR consult Genie Industries Service Department.
switch bad
5 - 22
Chart 9
Platform Down Function Inoperative, GS-3246
Be sure all other functions operate normally. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
With key switch in platform position and the platform raised slightly and both Emergency Stop buttons pulled out to the on position at both the ground and platform controls and the lift/drive switch in the lift position, activate the controller in the down direction and check to see if the error indicator light is on. With the platform raised and the safety arm installed, label and disconnect the wires from each coil on the platform lowering valves (item Q) at the platform lift cylinders and check the resistance of each valve coil. See Repair Section. 0 or infinite ohms Replace defective platform lowering valve coil (item Q).
light is on
23 to 25 ohms no Check continuity from continuity Repair open in ground the black ground wire at wire circuit from the the valve coil to ground. platform lowering valve coil (item Q) to ground. continuity With the platform raised and the safety arm removed, push the manual platform lowering button at the ground controls. platform does not lower See Chart 18 OR check for mechanical restrictions keeping platform from lowering OR repair or replace the platform lowering valve cartridge(s) (item Q) OR 0.059" orifice inside the cylinder(s) is plugged OR repair or replace lift cylinder(s) OR consult Genie Industries Service Department.
platform lowers Repair open in white wire (B6-down coil) circuit from the ECM to the platform lowering valve coil (item Q) on the lower cylinder to the platform lowering valve coil (item Q) on the upper cylinder OR repair open in brown ground wire circuit from platform lowering valve coils to ground OR repair or replace the platform lowering valve cartridge (item Q) OR replace ECM OR consult Genie Industries Service Department.
light is not on
5 - 23
CHART 9
Label and disconnect the wires from the lift/ drive toggle switch (S7) at the platform controls and troublshoot toggle switch (see Repair Section). good Check for mechanical restrictions keeping platform from lowering OR repair or replace the platform lowering valve cartridge(s) (item Q) OR 0.059" orifice inside the cylinder(s) is plugged OR repair or replace lift cylinder(s) OR replace platform controls OR replace ECM OR consult Genie Industries Service Department.
switch bad
5 - 24
Chart 10
Steer Left Function Inoperative
Be sure all other functions operate normally. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
light is not on With key switch in platform position and both Emergency Stop buttons pulled out to the on position, activate the steer rocker switch in the left direction and check to see if the error indicator light at the platform controls is on. light is on Disconnect the wires from the coil on the steer left directional valve on the function manifold (item G) and check the resistance of the valve coil. See Repair Section. 26 to 28 ohms Check continuity from the brown ground wire at the valve coil to ground. continuity Repair open in white wire (B7-left coil) from the coil on the steer left directional valve (item G) to the ECM OR repair open in brown ground wire circuit from the steer left directional valve (item G) to ground OR replace ECM OR consult Genie Industries Service Department. no Repair open in brown continuity ground wire circuit from the steer left directional valve coil (item G) to ground. 0 or infinite ohms Replace the coil.
Activate steer left function. Does the hydraulic power unit turn on?
no
Check continuity of steer microswitch. good Check for wire continuity from the steer microswitch to the terminal strip OR replace main circuit board at the platform controls.
bad
yes
5 - 25
CHART 10
Install a 0 to 2000 PSI pressure gauge at the quick disconnect coupling on the function manifold and activate the steer left function and check the pressure.
1500 PSI
Check for mechanical restrictions keeping steer left function from operating OR repair or replace steer cylinder OR consult Genie Industries Service Department.
less than 1500 PSI Re-adjust the steer relief valve (see Repair Section) OR repair or replace steer cylinder OR replace steer left/ right valve cartridge (item G) OR function manifold could have an internal defect. Consult Genie Industries Service Department.
5 - 26
Chart 11
Steer Right Function Inoperative
Be sure all other functions operate normally. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
light is not on With key switch in platform position and both Emergency Stop buttons pulled out to the on position, activate the steer rocker switch in the right direction and check to see if the error indicator light at the platform controls is on. light is on Disconnect the wires from the coil on the steer right directional valve on the function manifold (item G) and check the resistance of the valve coil. See Repair Section. 26 to 28 ohms Check continuity from the brown ground wire at the valve coil to ground. continuity Repair open in white wire (C7-right coil) from the coil on the steer right directional valve (item G) to the ECM OR repair open in brown ground wire circuit from the steer right directional valve (item G) to ground OR replace ECM OR consult Genie Industries Service Department. no Repair open in brown continuity ground wire circuit from the steer right directional valve coil (item G) to ground. 0 or infinite ohms Replace the coil.
Activate steer right function. Does the hydraulic power unit turn on?
no
Check continuity of steer microswitch. good Check for wire continuity from the steer microswitch to the terminal strip OR replace main circuit board at the platform controls.
bad
yes
5 - 27
CHART 11
Install a 0 to 2000 psi (0 to 138 bar) pressure gauge at the quick disconnect coupling on the function manifold and activate the steer right function and check the pressure.
1500 psi
Check for mechanical restrictions keeping steer right function from operating OR repair or replace steer cylinder OR consult Genie Industries Service Department.
less than 1500 psi Re-adjust the steer relief valve (see Repair Section) OR repair or replace steer cylinder OR replace steer left/ right valve cartridge (item G) OR function manifold could have an internal defect. Consult Genie Industries Service Department.
5 - 28
Chart 12
All Drive Functions Inoperative, All Other Functions Operate Normally
If the Error Indicator light is on at the platform controls, please refer to the specific chart that relates to the error code that is displayed on the ECM. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
Is the error indicator light on at the platform controls? yes Refer to chart(s) that are related to the error code that is displayed on the ECM OR consult Genie Industries Service Department. With key switch in platform position and both Emergency Stop buttons pulled out to the on position at both the ground and platform controls, activate drive forward and drive reverse functions. Check to see if the green indicator light is flashing at the platform controls. error Reset the ECM by indicator pushing in the platform light is Emergency Stop button on to the off position, switch the lift/drive selector switch to the drive position and pull the Emergency Stop button up to the on position. Check the lights at the platform controls. green light is flashing Test the lift/drive toggle switch S7 (see Repair Section). good light is not flashing Replace main circuit board in the platform controls OR replace ECM OR consult Genie Industries Service Department. bad Replace lift/drive toggle switch S7. Refer to chart(s) that are related to the error code that is displayed on the ECM OR consult Genie Industries Service Department.
light is flashing
no
Activate the drive forward or drive reverse function. Does the hydraulic power unit turn on?
no
Replace joystick controller OR replace main circuit board OR replace ECM OR consult Genie Industries Service Department.
yes
5 - 29
CHART 12
Chock both sides of the 3500 psi steer end drive wheels. Install a 0 to 5000 psi (0 to 345 bar) pressure gauge to the test port on the function manifold. Activate the drive function in either the forward or reverse direction and check the pressure. less than 3500 psi Repair or replace drive forward/reverse valve cartridge (item K) OR rebuild or replace drive motors OR function manifold may have an internal defect. Consult Genie Industries Service Department.
5 - 30
Chart 13
Brake Release Function Inoperative
If the Error Indicator light is on at the platform controls, please refer to the specific chart that relates to the error code that is displayed on the ECM. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
Chock the wheels at the steer end and raise the non-steer end of the machine up approximately 4 inches (10.2 cm) and place jack stands under the machine for support. Turn the brake release knob (item N) counterclockwise all the way and pump the hand pump fully 13-15 times or until much resistance is felt. Turn each wheel by hand. Each wheel should turn freely without much effort. wheels turn freely Turn the brake release valve (item N) clockwise all the way and try to rotate the wheels. wheels turn Rebuild or replace the brakes OR replace the brake release valve (item N) OR consult Genie Industries Service Department.
wheels do not turn Attempt to drive the machine in either direction and have someone try to rotate the non steer wheels (This will require 2 people). wheels turn Brake release function is operating correctly. If problems still exist consult Genie Industries Service Department.
wheels do not turn Plumb a 0 to 500 psi (34.5 bar) into the hose from the function manifold to the brake. Attempt to drive the machine in either direction and read the pressure on the gauge. less than 200 psi Replace shuttle valve (item O) OR replace brake release valve (item N) OR function manifold or brake release manifold may have an internal defect OR consult Genie Industries Service Department.
5 - 31
Chart 14
Drive Forward Function Inoperative
Be sure all other functions operate normally. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
light is not on With key switch in platform position and both Emergency Stop buttons pulled out to the on position at both the ground and platform controls, activate drive controller in the forward direction and check to see if the error indicator light at the platform controls is on. light is on Disconnect the wire from the drive forward directional valve coil (item K) and check the resistance. See Repair Section. 18 to 20 ohms Check continuity from the brown ground wire at the valve coil to ground. continuity Repair or replace drive forward directional valve (item K) OR repair open in wht wire (C-6 forward coil) OR repair open in brown ground wire circuit from the drive forward directional valve to ground OR consult Genie Industries Service Department. no Repair open in brown continuity ground wire circuit from the drive forward directional valve coil (item K) to ground. 0 or infinite ohms Replace drive forward directional valve coil (item K).
Replace the drive forward/reverse valve cartridge (item K) OR consult the Genie Industries Service Department..
5 - 32
Chart 15
Drive Reverse Function Inoperative
Be sure all other functions operate normally. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
light is not on With key switch in platform position and both Emergency Stop buttons pulled out to the on position at both the ground and platform controls, activate drive controller in the reverse direction and check to see if the error indicator light at the platform controls is on. light is on Disconnect the wire from the drive reverse directional valve coil (item K) and check the resistance. See Repair Section. 18 to 20 ohms Check continuity from the brown ground wire at the valve coil to ground. continuity Repair or replace drive reverse directional valve (item K) OR repair open in wht wire (A-7 reverse coil) OR repair open in brown ground wire circuit from the drive reverse directional valve to ground OR consult Genie Industries Service Department. no Repair open in brown continuity ground wire circuit from the drive reverse directional valve coil (item K) to ground. 0 or infinite ohms Replace drive reverse directional valve coil (item K).
Replace the drive forward/reverse valve cartridge (item K) OR consult the Genie Industries Service Department.
5 - 33
Chart 16
Machine Will Not Drive At Full Speed
Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged. Be sure that the drive speed select switch is in the down position.
With key switch in platform position and both Emergency Stop buttons pulled out to the ON position at both the ground and platform controls, and the platform in the stowed position, drive the machine in either direction. Is the error indicator light on at the platform controls? light is on Check voltage at white wire (39C-pothole sw) at S5. 24V Raise the platform approximately 3 feet (0.9 m) and check voltage at output side of S5. 24V Check voltage on input side of S6. 0V Repair open in white wire jumper (21Bpothole jumper) from output side of S5 to input side of S6. Adjust limit switch S5 so pothole arm activates switch OR replace limit switch contact OR replace limit switch S5. 0V Repair open in white wire (39C-pothole sw) from S5 to multi-function alarm to keyswitch.
0V
24V
0V
Adjust limit switch S6 so pothole arm activates switch OR replace limit switch contact OR replace limit switch S6.
Repair open in wht wire (B10-pothole sw) from the output side of S6 to the ECM OR replace ECM OR consult Genie Industries Service Department.
5 - 34
CHART 16
Chock both sides of the steer end drive wheels. Install a 0 to 5000 psi (0 to 345 bar) pressure gauge to the test port on the function manifold. Drive the machine in either the forward or reverse direction and check the pressure. 3500 psi Raise the steer end of machine up approximately 4 inches (10.2 cm) and place jack stands under the machine for support. With the lift/drive selector switch in the drive position, move the joystick controller to the full speed forward or reverse position. both wheels move Repair open in white wire (B10-pothole switch) from output side of S6 to ECM OR replace ECM OR see Chart 13, Brake Release Function Inoperative.
Re-adjust drive relief valve (see Repair Section) OR replace drive relief valve (item F) OR rebuild or replace drive motors OR function manifold may have an internal defect. Consult Genie Industries Service Department.
5 - 35
Chart 17
Machine Drives At Full Speed With Platform Raised
With key switch in platform position and both Emergency Stop buttons pulled out to the ON position at both the ground and platform controls and the platform in the stowed position, drive the machine in either direction. Is the error indicator light on at the platform controls? light is on Remove obstruction from pothole guard or from pothole guard limit switches OR consult Genie Industries Service Department. light is not on Consult Genie Industries Service Department.
5 - 36
Chart 18
Manual Platform Lowering Function Inoperative GS-2046 & GS-2646
Be sure the platform lowering cable is not kinked or pinched. Be sure the platform lowers using the platform up/down toggle switch at the ground controls.
Check the adjustment of the manual platform lowering cable. See 4-1 in the Repair Section, How to Adjust the Manual Platform Lowering Cable. Is the adjustment correct? yes See Chart 7 OR check for mechanical restrictions keeping manual platform lowering function from operating OR replace the manual platform lowering cable OR see OR consult Genie Industries Service Department. If manual platform lowering function is still inoperative, see Chart 7 OR consult Genie Industries Service Department. no Re-adjust the manual platform lowering cable and check the manual platform lowering function.
5 - 37
Chart 19
Manual Platform Lowering Function Inoperative GS-3246
Be sure the wiring to the platform lowering valves on the cylinders is not kinked or pinched. Be sure the platform lowers using the platform up/down toggle switch at the ground controls. Be sure the batteries are fully charged.
With the platform raised and the safety arm installed, connect the positive lead from a voltmeter to the wht wire on the lower lift cylinder solenoid valve and the negative lead of the volt meter to the brown ground wire on the hour meter. Activate the manual platfrom lowering button and check the voltage at the solenoid valve on the lower cylinder. less than 24V Remove the cover from the ground controls, then activate the manual platfrom lowering button and check the voltage on the wht wire at terminal #4 on the manual platform lowering button. less than 24V Check the voltage on the wht wire at terminal #3 on the manual platform lowering button. less than 24V Check continuity to Replace the diode on ground from the blk wire the wht wire from the on the manual platform continuity Emergency Stop button lowering battery that to the manual lowering connects to the brown button and re-charge the wire on the hour meter. manual platform lowering batteries OR replace the batteries. no continuity Repair open in ground wire circuit from the blk wire at the manual platform lowering batteries through the brown wire to the hour meter then to ground. 24V Replace the manual platform lowering button contact. Repair open in wht wire from terminal #4 at the manual platform lowering button to the solenoid valve on the lower lift cylinder. 24V Activate the manual platfrom lowering button and check the voltage on the wht wire at the solenoid valve on the upper cylinder. less than 24V Repair open in wht wire from the solenoid valve on the lower lift cylinder to the solenoid valve on the upper cylinder. 24V Check for mechanical restrictions keeping platform from lowering OR replace the solenoid valves on both lift cylinders OR the 0.059" orifice inside each lift cylinder may be plugged.
24V
5 - 38
Chart 20
Drive Function Overspeeds While Driving Down An Incline, GS-3246 Only
Be sure all other functions operate normally. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
With key switch in platform position and both Emergency Stop buttons pulled out to the ON position at both the ground and platform controls, activate drive controller in the forward direction down a slight incline. Does the machine overspeed? no The machine should be functioning normally. If not, consult Genie Industries Service Department. yes Adjust the Back Pressure Relief Valve (item L) (see repair section).
5 - 39
Chart 21
Drive Function Hesitates While Steering, GS-3246 Only
Be sure all other functions operate normally. Be sure the circuit breaker and fuse are not tripped or blown. Be sure the batteries are properly connected. Be sure the batteries are fully charged.
With key switch in platform position and the Emergency Stop buttons pulled out to the ON position at both the ground and platform controls, and the steer wheels turned fully to the right, activate drive controller in the forward direction. Does the drive function hesitate? no The machine should be functioning normally. If not, consult Genie Industries Service Department. yes Adjust the Back Pressure Relief Valve (item L) (see repair section).
5 - 40
Section 6 - Schematics
Schematics
About This Section
There are two groups of schematics in this section. An illustration legend precedes each group of drawings. Electrical Schematics
Electrocution hazard. Contact with electrically charged circuits may result in death or serious injury. Remove all rings, watches and other jewelry. Hydraulic Schematics Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. General Repair Process
Before Troubleshooting:
Read, understand and obey the safety rules and operating instructions printed in the Genie GS-2032 & Genie GS-2046 & Genie GS-2646 & Genie GS-3246 Operator's Manual. Be sure that all necessary tools and test equipment are available and ready for use.
Malfunction discovered
Identify symptoms
Troubleshoot
Return to service
problem solved
Perform repair
6-1
Section 6 - Schematics
Electrical Components
Item
Description
Manufacturer
Qty
AP1 ................ Anderson connector ............ 19436 ............. Anderson ............................. 6325-G1 ......................... 2 B1 ................... Alarm, steady tone .............. 39540 ............. Floyd Bell Inc. ...................... UC-09628-Q .................. 1 B2 ................... Alarm, intermittent ............... 18963 ............. Floyd Bell Inc. ...................... XB-09-630-Q .................. 1 F1 ................... Fuse, 275 amp .................... 40833 ............. Buss ..................................... ANN-275 ........................ 2 F2 ................... Circuit breaker ..................... 47811 ............. ETA ...................................... 45-700-IG1-P10 ............. 2 FB1 ................ Flashing beacon .................. 39676 ............. ECCO Electronic Controls ... 6220A ............................. 2 G1 .................. Battery, 225AH, 6V DC ....... 62201 ............. Allied Battery Co.. ................ GC2B, dry ...................... 4 G2 .................. Battery, 0.8AH, 12V DC ...... 55350 ............. Yuasa ................................... NP0.8-12 ........................ 2 H1 .................. Hourmeter ............................ 56100 ............. Curtis Instruments ............... 17305666 ....................... 1 P2 ................... Level sensor, Dual Axis ....... 40836 ............. Power Comp. of Midwest .... L36 ................................. 1 S1 ................... Contact, N.C. ....................... 33020 ............. Square D .............................. 1863 ............................... 1 S2, S12 .......... Contact, N.O. ....................... 45081 ............. Telemecanique .................... ZB2-BE101 .................... 5 S3 ................... Toggle switch, SPDT 3 position momentary .......... 13037 ............. Microswitch Control Inc. ...... 1NT1-7 ........................... 1 S4, S5, S6 S11 ................. Contact - limit switch, N.C.H.O. .............................. 19491 ............. Telemecanique .................... XESP2151 ..................... 4 S7, S8 ............ Toggle switch, DPDT 2 position maintained .......... 44987 ............. ITT Schadow. ...................... 220536 ........................... 2 S9 ................... Contact, N.C. ....................... 44990 ............. Telemecanique .................... ZA2-BZ1026 ................... 1 S10 ................. Contact, N.O. ....................... 44989 ............. Telemecanique .................... 220518 ........................... 1 U2 .................. Motor controller, 275 amp .............................. 39472 ............. Curtis Instruments ............... 1204-036 ........................ 1 Y2, Y3, Y4 ...... Coil, 20V DC (size 8) with diode ................ 39347 ............. Hydra Power Systems ......... 6309757 ......................... 3 Y1, Y5, Y6, Y8 ................... Coil, 20V DC (size10) with diode ............... 44176 ............. Hydra Power Systems ......... 6359752 ......................... 4 Y7 ................... Coil, 20V DC ........................ 44787 ............. Hydra Power Systems ......... 10166-25 ........................ 3
6-2
Section 6 - Schematics
6-3
Section 6 - Schematics
6-4
Section 6 - Schematics
6-5
Section 6 - Schematics
6-6
Section 6 - Schematics
Service Manual
6-7
Service Manual
Section 6 - Schematics
6-8
Service Manual
Section 6 - Schematics
Section 6 - Schematics
Service Manual
6-9
Service Manual
Section 6 - Schematics
6 - 10
Service Manual
Section 6 - Schematics
Section 6 - Schematics
Service Manual
6 - 11
Service Manual
Section 6 - Schematics
6 - 12
Service Manual
Section 6 - Schematics
Section 6 - Schematics
Service Manual
6 - 13
Service Manual
Section 6 - Schematics
6 - 14
Service Manual
Section 6 - Schematics
Section 6 - Schematics
6 - 15
Section 6 - Schematics
6 - 16
Section 6 - Schematics
6 - 17
Section 6 - Schematics
6 - 18
Service Manual
Section 6 - Schematics
6 - 19
Service Manual
Section 6 - Schematics
Service Manual
Section 6 - Schematics
6 - 20
Service Manual
Section 6 - Schematics
Repair Procedures
About This Section
Most of the procedures in this section should only be performed by a trained service professional in a suitably equipped workshop. Select the appropriate repair procedure after troubleshooting the problem.
Perform disassembly procedures to the point where repairs can be completed. Then to re-assemble, perform the disassembly steps in reverse order. Symbols Legend Safety alert symbolused to alert personnel to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Redused to indicate the presence of an imminently hazardous situation which, if not avoided, will result in death or serious injury. Orangeused to indicate the presence of a potentially hazardous situation which, if not avoided, could result in death or serious injury. Yellow with safety alert symbol used to indicate the presence of a potentially hazardous situation which, if not avoided, may cause minor or moderate injury. Yellow without safety alert symbolused to indicate the presence of a potentially hazardous situation which, if not avoided, may result in property damage. Greenused to indicate operation or maintenance information. Indicates that a specific result is expected after performing a series of steps.
7-1
Platform Controls
1-1 Platform Controller
The platform controller is controlled by an ECM (Electronic Control Module) located in the power unit module tray. The ECM aids in troubleshooting by recognizing machine malfunctions and displaying fault codes on an LED screen on the ECM. See the Troubleshooting section of this manual for a list of fault codes and additional information. The ECM is not user-serviceable. The joystick controller is calibrated at the factory and does not need to be adjusted. For further information or assistance, consult the Genie Industries Service Department.
c b c d e d
f a b c d e f Main circuit board Lift/drive selector toggle switch Horn button Emergency stop button LED circuit board Joystick controller a b c d Main circuit board Emergency stop button Joystick controller Alarm
7-2
PLATFORM CONTROLS
3 Press and hold the lift enable button and the function enable switch. Move the joystick handle to the UP position to raise the platform. Observe the code shown in the LED display window, located on the battery pack side of the machine. Result: The configuration code of the DIP switch will appear in the LED display window. 4 Press and hold the lift enable button and the function enable switch. Move the joystick handle to the DOWN position to lower the platform. Observe the code shown in the LED display window, located on the battery pack side of the machine. Result: The software revision level will appear in the LED display window. If revision level "b0" or later appears in the display window, the following procedures will apply. If revision level "A0" is displayed, the following procedures will not apply. 5 Push in the Emergency Stop button to the OFF position at both the ground and platform controls and turn the key switch to the OFF position.
7-3
PLATFORM CONTROLS
3 Rotate the platform controller box in the position shown to correctly identify the configuration of the DIP switch settings. 4 Open the controller box lid and locate the DIP switch on the circuit board. Move the DIP switch settings to correspond with the configuration of the machine options, indicated in the DIP Switch Code Chart. 5 Confirm the settings. See 1-3, How to Determine the Revision Level. 6 Cover the DIP switch with dielectric grease. 7 Close the lid and install the fasteners. 8 Push in the Emergency Stop button to the OFF position at both the ground and platform controls and turn the key switch to the OFF position. Any change in DIP switch settings will not take effect until the key switch is truned to the OFF position.
a b c d e f
DIP switch Emergency stop button Circuit boards Joystick controller Controller box Enlarged view of DIP switch
7-4
PLATFORM CONTROLS
Motion Beacon
Descent Delay
Motion Alarm
Lift/Drive Cut Out: This cuts out lift and drive functions when the machine goes out of level. Required for Europe and Australia. Overload Cut Out: This cuts out lift when the cylinder is overloaded. Required for France. Descent Delay: This option halts descent for 4 seconds at approximately 6 feet (2 m). Required for Europe.
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
10000000 10000100 10001000 10010000 10100000 11000000 10001100 10010100 10100100 11000100 10011100 10101100 11001100 10110100 11010100 11100100 10111100 11011100 11101100 11110100 11111100 10011000 10101000 11001000 10111000 11011000 11101000 11111000 10110000 11010000 11110000 11100000
7-5
PLATFORM CONTROLS
Test Left position terminal 1 to 2, 3, 4, 5 & 6 terminal 2 to 3 terminal 2 to 4, 5 & 6 terminal 3 to 4, 5 & 6 terminal 4 to 5 & 6 terminal 5 to 6 Center position
Desired result
no continuity (infinite ) continuity (zero ) no continuity no continuity no continuity continuity There are no terminal combinations that will produce continuity (infinite )
Right position terminal 1 to 2 terminal 1 to 3, 4, 5 & 6 terminal 2 to 3, 4, 5 & 6 terminal 3 to 4, 5 & 6 terminal 4 to 5 continuity (zero ) no continuity (infinite ) no continuity no continuity continuity no continuity no continuity
Left
Center
Right
terminal 4 to 6 terminal 5 to 6
1 2
1 2
1 2
Single pole double throw (SPDT) Double pole double throw (DPDT)
1 4
2 5
3 6
1 4
2 5
3 6
1 4
2 5
3 6
7-6
Platform Components
2-1 Platform How to Remove the Platform
Perform this procedure with the platform extension fully retracted and locked in position. 1 Lower the platform to the stowed position and turn the machine off. 2 Remove the retaining fastener that holds the platform controls quick disconnect plug to the bottom of the platform toeboard. 3 Twist to disconnect the plug from the platform controls. 4 Remove the cover to the AC outlet. Label and disconnect the wiring from the outlet. Electrocution hazard. Contact with electrically charged circuits may result in death or serious injury. Remove all rings, watches and other jewelry. 5 Pull the wiring through the platform tube. If your machine is equipped with an air line to platform option, the air line must be disconnected from the platform before removal. 6 Support the platform with a forklift at the non-steer end. Do not lift it. 7 Attach a strap from the platform railings to the carriage on the forklift to help support the platform. 8 Remove the retaining fasteners from the scissor platform pivot pins at the steer end of the machine. 9 Use a slide hammer to remove the pins. Crushing hazard. The platform will fall if it is not properly supported. 10 Remove the plug from the access hole on each side of the platform. 11 Lift the platform slightly to clear the scissor arms and slide the platform towards the nonsteer end of the machine until the non-steer end platform pivot pins are visible through the access holes in the side of the platform. 12 Remove the retaining fasteners from the scissor platform pivot pins at the non-steer end of the machine. 13 Use a slide hammer to remove the pins. Crushing hazard. The platform may may become unbalanced and fall when it is removed from the machine if it is not properly supported and secured to the forklift. 14 Carefully lift the platform off of the machine and place it on a structure capable of supporting it. Note the position of the wear pads before the platform is removed so that when the platform is installed they will be in the correct position.
7-7
PLATFORM COMPONENTS
7-8
7-9
Scissor Components
Steer End
1 2 3 4 5 6 7 8 9 Number 4 pivot pin (steer end) Number 3 center pivot pin Lift cylinder rod-end pivot pin Number 3 pivot pin (steer end) Number 2 center pivot pin (2pins) Number 2 pivot pin (steer end) Number 1 center pivot pin Number 1 inner arm Number 1 pivot pin (steer end) (2pins) 10 11 12 13 14 15 16 17 18
Non-steer End
Number 4 pivot pin (non-steer end) Number 3 inner arm Number 3 outer arm Number 3 pivot pin (non-steer end) Number 2 inner arm Number 2 outer arm Number 2 pivot pin (non-steer end) Lift cylinder barrel-end pivot pin Number 1 outer arm
7 - 10
5 Use a soft metal drift to remove the number 3 center pivot pin (index #2). 6 Remove the external snap rings from the number 3 pivot pin (index #13). 7 Use a soft metal drift to remove the number 3 pivot pin (index #13) from the non-steer end of the machine. Remove the number 3 outer arm (index #12) from the machine. Crushing hazard. The number 3 outer arm (index #12) may become unbalanced and fall if not properly supported when it is removed from the machine. 8 Remove the cable clamps from the number 3 inner arm (index #11). 9 Remove the mounting fasteners from the cable tray support at the steer end. 10 Remove the external snap rings from the number 2 center pivot pin (index #5) at the ground controls side. Do not remove the pin. 11 Slide the cable tray towards the battery pack side of the machine and remove it from the machine. Component damage hazard. Cables can be damaged if they are kinked or pinched. 12 Attach a lifting strap from an overhead crane to the lug on the rod end of the lift cylinder. 13 Remove the pin retaining fasteners from the cylinder rod-end pivot pin (index #3). Use a soft metal drift to remove the pin. Bodily injury hazard. The cylinder may fall if not properly supported when the pin is removed.
7 - 11
14 Lower the cylinder onto the number 1 center pivot pin (index #7). 15 Attach a lifting strap from an overhead crane to the number 3 inner arm (index #11). 16 Remove the external snap rings from the number 3 pivot pin (index #4). 17 Use a soft metal drift to remove the number 3 pivot pin (index #4). Remove the number 3 inner arm (index #11) from the machine. Bodily injury hazard. The number 3 inner arm (index #11) may become unbalanced and fall if not properly supported when it is removed from the machine. 18 Attach a strap from an overhead crane to the number 2 outer arm (index #15) at the ground controls side. 19 Use a soft metal drift to remove the number 2 center pivot pin (index #5) at the ground controls side. 20 Remove the external snap rings from the number 2 pivot pin (index #16) at the non-steer end. 21 Use a soft metal drift to remove the number 2 pivot pin (index #16) at the non-steer end. Remove the number 2 outer arm (index #15) from the ground controls side of the machine. Bodily injury hazard. The number 2 outer arm (index #15) at the ground controls side may become unbalanced and fall if not properly supported when it is removed from the machine.
22 Attach a lifting strap from an overhead crane to the number 2 outer arm (index #15) at the battery pack side. 23 Remove the external snap rings from the number 2 center pivot pin (index #5) at the battery pack side. 24 Use a soft metal drift to remove the number 2 center pivot pin (index #5) at the battery pack side. Remove the number 2 outer arm (index #15) from the battery pack side of the machine. Bodily injury hazard. The number 2 outer arm (index #15) at the battery pack side may become unbalanced and fall if not properly supported when it is removed from the machine. 25 Attach a lifting strap from an overhead crane to the number 2 inner arm (index #14). 26 Remove the external snap rings from the number 2 pivot pin (index #6) from the steer end of the machine. 27 Use a soft metal drift to remove the number 2 pivot pin (index #6). Remove the number 2 inner arm (index #14) from the machine. Bodily injury hazard. The number 2 outer arm (index #15) at the battery pack side may become unbalanced and fall if not properly supported when it is removed from the machine. 28 Remove the safety arm from the number 2 inner arm (index #14) that was just removed.
7 - 12
29 Attach a lifting strap from an overhead crane to the number 1 inner arm (index #8) at the nonsteering end. 30 Raise the number 1 inner arm (index #8) approximately 2 feet (0.6 m) and insert the safety arm between the number 1 inner arm (index #8) and the number 1 outer arm (index #18). Lower the scissor arms onto the safety arm. Bodily injury hazard. Keep hands clear of moving parts when inserting the safety arm. 31 Disconnect and plug the hydraulic hose on the lift cylinder. Cap the fitting on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 32 Tag and disconnect the wires from the solenoid valve on the cylinder. 33 Attach a lifting strap from an overhead crane to the lug on the rod end of the lift cylinder. Raise the lift cylinder to a vertical position.
34 Remove the pin retaining fasteners from the lift cylinder barrel-end pivot pin (index #17). Use a soft metal drift to remove the pin. Remove the cylinder from the machine. Crushing hazard. The cylinder may become unbalanced and fall when it is removed from the machine if it is not properly attached to the overhead crane. Component damage hazard. Be careful not to damage the valve or fittings on the cylinder while removing it from the machine. 35 Place a 4 x 4 x 48 inch (10 x10 x122 cm) long block across both sides of the chassis under the number 1 center pivot pin (index #7). 36 Attach a lifting strap from an overhead crane to the number 1 inner arm (index #8) at the nonsteer end. Raise the number 1 inner arm (index #18) and remove the safety arm. Lower the number 1 inner arm (index #8) onto the block that was placed across the chassis. Bodily injury hazard. Keep hands clear of moving parts when lowering the arms onto the block. 37 Remove the cables from the number 1 inner arm (index #8)and lay them off to the side. Component damage hazard. Cables can be damaged if they are kinked or pinched.
7 - 13
38 Support and secure the entry ladder to an appropriate lifting device. 39 Remove the entry ladder mounting fasteners. Remove the entry ladder from the machine. Crushing hazard. The entry ladder may become unbalanced and fall if not properly suported and secured to the lifting device. 40 Attach the strap from the overhead crane to the number 1 outer arm (index #18). Do not lift it. 41 Remove the external snap rings from the number 1 center pivot pin (index #7). 42 Use a soft metal drift to remove the number 1 center pivot pin (index #7). Bodily injury hazard. The number 1 inner arm (index #18) may become unbalanced and fall if not properly supported when the pin is removed. 43 Slide the number 1 outer arm (index #18) to the non-steer end and remove it from the machine. Bodily injury hazard. The number 1 outer arm (index #18) may become unbalanced and fall if not properly supported when removing it from the machine. 44 Attach the strap from an overhead crane to the number 1 inner arm (index #8). Do not lift it. 45 Remove the pin retaining fasteners from both of the number 1 pivot pins (index #9). Use a slide hammer to remove the pins. 46 Remove the number 1 inner arm (index #8) from the machine. Bodily injury hazard. The number 1 inner arm (index #8) may become unbalanced and fall if not properly supported when removed from the machine.
7 - 14
12 Remove the level sensor box mounting fasteners and slide the box towards the nonsteer end of the machine as far as it can go. Component damage hazard. Be careful not to damage the level sensor box, limit switch, level sensor or wiring while moving the level sensor box. 13 Secure the ends of the scissor arms together at both ends of the machine with a tie down strap or other appropriate device. 14 Remove the pin retaining fasteners from the number 1 inner arm pivot pins (item #9) at the steer end of the machine. Use a slide hammer to remove the pins. 15 Attach a lifting strap from an overhead crane to the steer end of the scissor arms. 16 Carefully slide the forks from a forklift under the scissor arms at the non-steer end of the machine. 17 Raise the scissor arms up until the number 1 inner arm will clear the level sensor box. Component damage hazard. Be careful not to damage the level sensor box, limit switch or level sensor while moving the scissor assembly. 18 Move the scissor assembly towards the nonsteer end of the machine slightly and to one side of the machine until one of the scissor arm wear pads is accessible. Do not allow both wear pads to slide out of the drive chassis. Crushing hazard. The scissor assembly will fall if both wear pads are allowed to slide out of the drive chassis.
19 Remove the old wear pad. Note the position of the wear pad before it is removed so when the new one is installed it will be in the correct position. 20 Install the new wear pad. 21 Move the scissor assembly towards the other side of the machine until the other scissor arm wear pad is accessible. Crushing hazard. The scissor assembly will fall if both wear pads are allowed to slide out of the drive chassis. 22 Remove the old wear pad. Note the position of the wear pad before it is removed so when the new one is installed it will be in the correct position. 23 Install the new wear pad. 24 Slide the scissor assembly back into the drive chassis. 25 Lower the scissor assembly into position and install the pivot pins. Component damage hazard. Be careful not to damage the level sensor box, limit switch or level sensor while installing the scissor assembly.
7 - 15
SCISSOR COMPONENTS
Steer End
1 2 3 4 5 6 7 8 9 10 11 12 Number 5 pivot pin (steer end) Number 4 center pivot pin Number 4 pivot pin (steer end) Number 3 outer arm Lift cylinder rod end pivot pin Number 3 pivot pin (steer end) Number 2 center pivot pin (2 pins) Number 2 pivot pin (steer end) Number 1 center pivot pin Number 1 inner arm Number 1 pivot pin (steer end) (2 pins) Number 5 pivot pin (non-steer end) 13 14 15 16 17 18 19 20 21 22 23
Non-steer End
Number 4 inner arm Number 4 outer arm Number 4 pivot pin (non-steer end) Number 3 inner arm Number 3 center pivot pin Number 3 pivot pin (non-steer end) Number 2 inner arm Number 2 outer arm Number 2 pivot pin (non-steer end) Lift cylinder barrel-end pivot pin Number 1 outer arm
7 - 16
7 Use a soft metal drift to remove the number 4 pivot pin (index #15) from the non-steer end of the machine. Remove the number 4 outer arm (index #14) from the machine. Crushing hazard. The number 4 outer arm (index #14) may become unbalanced and fall if not properly supported when it is removed from the machine. 8 Remove the cables from the upper cable tray and lay them off to the side. Component damage hazard. Cables can be damaged if they are kinked or pinched. 9 Remove the mounting fasteners from the upper cable tray supports. 10 Remove the upper cable tray from the scissor assembly. 11 Attach a lifting strap from an overhead crane to the number 4 inner arm (index #13). 12 Remove the external snap rings from the number 4 pivot pin (index #3). 13 Use a soft metal drift to remove the number 4 pivot pin (index #3) at the steer end. Remove the number 4 inner arm (index #13) from the machine. Crushing hazard. The number 4 inner arm (index #13) may become unbalanced and fall if not properly supported when it is removed. 14 Attach a lifting strap from an overhead crane to the number 3 outer arm (index #4) at the ground controls side. 15 Remove the external snap rings from the number 3 center pivot pin (index #17).
7 - 17
16 Use a soft metal drift to remove the number 3 center pivot pin (index#17). 17 Remove the external snap rings from the number 3 pivot pin (index #18) at the non-steer end of the machine. Do not remove the pin. 18 Use a soft metal drift to tap the number 3 pivot pin (index #18) halfway out at the non-steer end of the machine. Remove the number 3 outer arm (index #4) at the ground controls side from the machine. Bodily injury hazard. The number 3 outer arm (index #4) at the ground controls side may become unbalanced and fall if not properly supported when it is removed from the machine. 19 Attach a lifting strap from an overhead crane to the number 3 outer arm (index #4) at the battery pack side. 20 Use a soft metal drift to tap the number 3 pivot pin (index #18) in the other direction. Remove the number 3 outer arm (index #4) from the battery pack side of the machine. Bodily injury hazard. The number 3 outer arm (index #4) at the battey pack side may become unbalanced and fall if not properly supported when it is removed from the machine. 21 Remove the number 3 pivot pin (index #18) from the non-steer end of the machine. 22 Attach a lifting strap from an overhead crane to the lug on the rod end of the lift cylinder for support. Do not lift it.
23 Remove the pin retaining fasteners from the lift cylinder rod-end pivot pin (index #5). Use a soft metal drift to remove the pin. Bodily injury hazard. The cylinder may fall when the rod-end pivot pin is removed if it is not properly supported. 24 Lower the cylinder onto the number 1 center pivot pin (index #9). 25 Remove the cables from the number 3 inner arm (index #16) and lay them to the side. 26 Attach a lifting strap from an overhead crane to the number 3 inner arm (index #16). 27 Remove the external snap rings from the number 3 pivot pin (index #6) at the steer end. 28 Use a soft metal drift to remove the number 3 pivot pin (index #6). Remove the number 3 inner arm (index #16) from the machine. Bodily injury hazard. The number 3 inner arm (index #16) may become unbalanced and fall if not properly supported when it is removed from the machine. 29 Remove the cable clamps from the lower cable tray. Lay the cables to the side. Component damage hazard. Cables can be damaged if they are kinked or pinched. 30 Remove the mounting fasteners from the lower cable tray supports. 31 Remove the mounting fasteners from the lower cable tray mounting bracket on the number 2 center pivot pin (index #7) at the ground controls side of the machine.
7 - 18
32 Slide the cable tray towards the battery pack side of the machine and remove it from the machine. 33 Attach a lifting strap from an overhead crane to the number 2 outer arm (index #20) at the ground controls side. 34 Remove the external snap rings from the number 2 center pivot pin (index #7) at the ground controls side. 35 Use a soft metal drift to remove the number 2 center pivot pin (index #7) at the ground controls side. 36 Use a soft metal drift to tap the number 2 pivot pin (index #21) halfway out at the non-steer end of the machine. Remove the number 2 outer arm (index #20) from the ground controls side of the machine. Bodily injury hazard. The number 2 outer arm (index #20) at the ground controls side may become unbalanced and fall if not properly supported when it is removed from the machine. 37 Attach a lifting strap from an overhead crane to the number 2 outer arm (index #20) at the battery pack side. 38 Remove the external snap rings from the number 2 center pivot pin (index #7) at the battery pack side. 39 Use a soft metal drift to remove the number 2 center pivot pin (index #7) at the battery pack side. Bodily injury hazard. The number 2 outer arm (index #20) at the battery pack side may become unbalanced and fall if not properly supported when it is removed from the machine.
40 Use a soft metal drift to tap the number 2 pivot pin (index #21) in the other direction. Remove the number 2 outer arm (index #20) from the battery pack side of the machine. Bodily injury hazard. The number 2 outer arm (index #20) at the battery pack side may become unbalanced and fall if not properly supported when it is removed from the machine. 41 Attach a lifting strap from an overhead crane to the number 2 inner arm (index #19). 42 Remove the external snap rings from the number 2 pivot pin (index #8) at the steer end of the machine. 43 Use a soft metal drift to remove the number 2 pivot pin (index #8). Remove the number 2 inner arm (index #19) from the machine. Bodily injury hazard. The number 2 inner arm (index #19) may become unbalanced and fall if not properly supported when it is removed from the machine. 44 Remove the safety arm from the number 2 inner arm (index #19) that was just removed. 45 Attach a lifting strap from an overhead crane to the number 1 inner arm (index #10). 46 Raise the number 1 inner arm (index #10) approximately 2 feet (0.6 m) and install the safety arm between the number 1 inner arm (index #10) and the number 1 outer arm (index #23). Lower the scissor arms onto the safety arm. Bodily injury hazard. Keep hands clear of moving parts when inserting the safety arm.
7 - 19
47 Disconnect and plug the hydraulic hose on the lift cylinder. Cap the fitting on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 48 Tag and disconnect the wires from the solenoid valve on the cylinder. 49 Attach a lifting strap from an overhead crane to the lug on the rod end of the lift cylinder. Raise the lift cyinder to a vertical positon. 50 Remove the pin retaining fasteners from the lift cylinder barrel-end pin (index #22). Use a soft metal drift to remove the pin. Remove the cylinder from the machine. Crushing hazard. The cylinder may become unbalanced and fall when it is removed from the machine if it is not properly attched to the overhead crane. Component damage hazard. Be careful not to damage the valve or fittings on the cylinder while removing it from the machine. 51 Place a 4x4x48 inch (10x10x122 cm) long block across both sides of the chassis under the number 1 center pivot pin (index #9).
52 Attach a lifting strap from an overhead crane to the number 1 inner arm (index #10) at the nonsteer end. Raise the number 1 inner arm and remove the safety arm. Lower the number 1 inner arm (index #10) onto the block that was placed across the chassis. Bodily injury hazard. Keep hands clear of moving parts when lowering the arms onto the block. 53 Remove the cables and hydraulic hoses from the number 1 inner arm (index #10) and lay them to the side. Component damage hazard. Cables and hoses can be damaged if they are kinked or pinched. 54 Support and secure the entry ladder to an appropriate lifting device. 55 Remove the mounting fasteners from the entry ladder and remove the entry ladder from the machine. Crushing hazard. The entry ladder may become unbalanced and fall if not properly supported and secured to the lifting device. 56 Attach a lifting strap from an overhead crane to the number 1 outer arm (index #23). Do not lift it. 57 Remove the external snap rings from the number 1 center pivot pin (index #9).
7 - 20
58 Use a soft metal drift to remove the number 1 center pivot pin (index #9). Bodily injury hazard. The number 1 outer arm (index #23) may become unbalanced and fall if not properly supported when the pin is removed. 59 Slide the number 1 outer arm (index #23) to the non-steer end and remove it from the machine. Bodily injury hazard. The number 1 outer arm (index #23) may become unbalanced and fall if not properly supported when it is removed from the machine. Note the position of the wear pads before the arm is removed so when the scissor is assembled they will be in the correct position. 60 Attach the strap from an overhead crane to the number 1 inner arm (index #10). Do not lift it. 61 Remove the pin retaining fasteners from both of the number 1 pivot pins (index #11) at the steer end of the machine. Use a slide hammer to remove the pins.
62 Remove the number 1 inner arm (index #10) from the machine. Bodily injury hazard. The number 1 inner arm (index #10) may become unbalanced and fall if not properly supported when it is removed from the machine. Component damage hazard. Be sure not to damage the limit switch or level sensor box components when the number 1 inner arm (index #10) is removed from the machine.
7 - 21
5 Support and secure the entry ladder to an appropriate lifting device. 6 Remove the mounting fasteners from the entry ladder and remove the entry ladder from the machine. Crushing hazard. The entry ladder may become unbalanced and fall if not properly supported and secured to the lifting device. 7 Raise the platform approximately 7 to 8 feet (2.1 to 2.4 m). 8 Lift the safety arm, move to the center of the scissor arm and rotate down to a vertical position. 9 Lower the platform onto the safety arm. 10 Mark the mounting position of the level sensor box on the drive chassis. 11 Remove the level sensor box lid. 12 Mark the mounting position of the level sensor on the level sensor box. 13 Remove the level sensor mounting fasteners. 14 Remove the level sensor box mounting fasteners and slide the box towards the nonsteer end of the machine as far as it can go. Component damage hazard. Be careful not to damage the level sensor box, limit switch, level sensor or wiring while moving the level sensor box. 15 Secure the ends of the scissor arms together at both ends of the machine with a tie down strap or other appropriate device. 16 Remove the pin retaining fasteners from the number 1 inner arm pivot pins (item #11) at the steer end of the machine. Use a slide hammer to remove the pins.
17 Attach a lifting strap from an overhead crane to the steer end of the scissor arms. 18 Carefully slide the forks from a forklift under the scissor arms at the non-steer end of the machine. 19 Raise the scissor arms up until the number 1 inner arm will clear the level sensor box. Component damage hazard. Be careful not to damage the level sensor box, limit switch or level sensor while moving the scissor assembly. 20 Move the scissor assembly towards the nonsteer end of the machine slightly and to one side of the machine until one of the scissor arm wear pads is accessible. Do not allow both wear pads to slide out of the drive chassis. Crushing hazard. The scissor assembly will fall if both wear pads are allowed to slide out of the drive chassis. 21 Install the new wear pad. Note the position of the wear pad before it is removed so when the new one is installed it will be in the correct position. 22 Move the scissor assembly towards the other side of the machine until the other scissor arm wear pad is accessible. Crushing hazard. The scissor assembly will fall if both wear pads are allowed to slide out of the drive chassis.
7 - 22
23 Install the new wear pad. Note the position of the wear pad before it is removed so when the new one is installed it will be in the correct position. 24 Slide the scissor assembly back into the drive chassis. 25 Lower the scissor assembly into position and install the pivot pins. Component damage hazard. Be careful not to damage the level sensor box, limit switch or level sensor while installing the scissor assembly.
7 - 23
Steer end
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Number 6 pivot pin (steer end) Number 5 center pivot pin Upper lift cylinder rod-end pivot pin Number 5 pivot pin (steer end) Number 4 center pivot pin (2 pins) Number 4 pivot pin (steer end) Number 3 outer arm Number 3 center pivot pin Lower lift cylinder rod-end pivot pin Number 3 pivot pin (steer end) Number 2 center pivot pin (2 pins) Number 2 pivot pin (steer end) Number 1 center pivot pin Number 1 inner arm Number 1 pivot pin (steer end) (2 pins) 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
7 - 24
6 Remove the external snap rings from the number 5 pivot pin (index #19). 7 Use a soft metal drift to remove the number 5 pivot pin (index #19) from the non-steer end of the machine. Remove the number 5 outer arm (index #18) from the machine. Crushing hazard. The number 5 outer arm (index #18) may become unbalanced and fall if not properly supported when it is removed from the machine. 8 Remove the cable clamps from the number 5 inner arm (index #17). Lay the cables off to the side of the machine. 9 Remove the mounting fasteners from the upper cable tray supports. 10 Remove the mounting fasteners from the upper cable tray mounting bracket on the number 4 center pivot pin (index #5) at the ground controls side of the machine. 11 Remove the upper cable tray from the scissor assembly. Component damage hazard. Cables can be damaged if they are kinked or pinched. 12 Attach a lifting strap from an overhead crane to the lug on the rod end of the upper lift cylinder. 13 Remove the pin retaining fasteners from the upper cylinder rod-end pivot pin (index #3). Use a soft metal drift to remove the pin. Crushing hazard. The cylinder may fall if not properly supported when the pin is removed. 14 Lower the cylinder onto the number 3 center pivot pin (index #8).
7 - 25
15 Attach a lifting strap from an overhead crane to the number 5 inner arm (index #17). 16 Remove the external snap rings from the number 5 pivot pin (index #4). 17 Use a soft metal drift to remove the number 5 pivot pin (index #4). Remove the number 5 inner arm (index #17) from the machine. Bodily injury hazard. The number 5 inner arm (index #17) may become unbalanced and fall if not properly supported when it is removed from the machine. 18 Remove the external snap rings from the number 4 center pivot pin (index #5) at the ground controls side. 19 Remove the external snap rings from the number 4 center pivot pin (index #5) at the battery pack side. 20 Use a soft metal drift to remove both of the number 4 center pivot pins (index #5). 21 Remove the external snap rings from the number 4 pivot pin (index #22) at the non-steer end of the machine. 22 Use a soft metal drift to remove the number 4 pivot pin (index #22). Remove the number 4 outer arm (index #21) from the machine. Bodily injury hazard. The number 4 outer arm (index #21) may become unbalanced and fall if not properly supported when it is removed from the machine. 23 Attach a lifting strap from an overhead crane to the number 4 inner arm (index #20). 24 Remove the external snap rings from the number 4 pivot pin (index #6) from the steer end of the machine.
25 Use a soft metal drift to remove the number 2 pivot pin (index #12). Remove the number 2 inner arm (index #26) from the machine. Bodily injury hazard. The number 4 inner arm (index #20) may become unbalanced and fall if not properly supported when it is removed from the machine. 26 Remove the safety arm from the number 4 inner arm (index #20) that was just removed. 27 Disconnect and plug the hydraulic hose on the lift cylinder. Cap the fitting on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 28 Tag and disconnect the wires from the solenoid valve on the cylinder. 29 Connect the platform controls to the control cable that was removed from the platform. 30 Connect the battery pack. Turn the key switch to ground control and pull out the Emergency Stop button to the ON position at both the platform and ground controls. 31 Activate the up function and raise the number 2 inner arm (index #26) approximately 2 feet (0.6 m). Then install the safety arm between the number 2 inner arm (index #26) and the number 1 inner arm (index #14). Bodily injury hazard. Keep hands clear of moving parts when inserting the safety arm.
7 - 26
32 Activate the down function to lower the scissor assembly onto the safety arm. Push in the Emergency Stop buttons and turn the key to the OFF position. Bodily injury hazard. The scissor assembly may become unbalanced and fall if not properly supported by the safety arm. Bodily injury hazard. Keep hands clear of moving parts when inserting the safety arm. 33 Attach a lifting strap from an overhead crane to the lug on the rod end of the upper lift cylinder. Raise the rod end of the cylinder to a vertical position. 34 Remove the pin retaining fasteners from the upper lift cylinder barrel-end pivot pin (index #23). Use a soft metal drift to remove the pin. Remove the cylinder from the machine. Crushing hazard. If the overhead crane is not properly attached, the cylinder may become unbalanced and fall when it is removed from the machine. Component damage hazard. Be careful not to damage the valve or fittings on the cylinder while removing it from the machine. 35 Turn the key switch to ground control and pull out the Emergency Stop button to the ON position at both the platform and ground controls.
36 Activate the up fuction and raise the number 2 inner arm (index #26) approximately 2 feet (0.6 m). Remove the safety arm from the machine. Bodily injury hazard. Keep hands clear of moving parts when removing the safety arm. 37 Activate the down function and fully lower the scissor assembly. Push in the Emergency Stop button and turn the key to the OFF position. Disconnect the battery pack. Bodily injury hazard. Keep hands clear of moving parts when lowering the scissor assembly. 38 Attach a lifting strap from an overhead crane to the number 3 outer arm (index #7) at the ground controls side. 39 Remove the external snap rings from the number 3 center pivot pin (index #8). 40 Use a soft metal drift to remove the number 3 center pivot pin (index #8). 41 Remove the external snap rings from the number 3 pivot pin (index #25) at the non-steer end of the machine. Do not remove the pin. 42 Use a soft metal drift to tap the number 3 pivot pin (index #25) halfway out at the non-steer end of the machine. Remove the number 3 outer arm (index #7) at the ground controls side from the machine. Bodily injury hazard. The number 3 outer arm (index #7) at the ground controls side may become unbalanced and fall if not properly supported when removed from the machine.
7 - 27
43 Attach a lifting strap from an overhead crane to the number 3 outer arm (index #7) at the battery pack side. 44 Use a soft metal drift to tap the number 3 pivot pin (index #10) at the steer end in the other direction. Remove the number 3 outer arm (index #7) from the battery pack side of the machine. Bodily injury hazard. The number 3 outer arm (index #7) at the battery pack side may become unbalanced and fall if not properly supported when it is removed from the machine. 45 Remove the cables from the number 3 inner arm (index #24) and lay them off to the side. Component damage hazard. Cables can be damaged if they are kinked or pinched. 46 Remove the cables from the lower cable tray on the number 2 inner arm (index #26). Lay the cables off th the side. 47 Remove the mounting fasteners from the lower cable tray supports. 48 Remove the external snap rings from the number 2 center pivot pin (index #11) at the ground controls side. Do not remove the pin. 49 Slide the cable tray towards the battery pack side of the machine and remove it from the machine. Component damage hazard. Cables can be damaged if they are kinked or pinched. 50 Attach a lifting strap from an overhead crane to the lug on the rod end of the lower lift cylinder.
51 Remove the pin retaining fasteners from the lower lift cylinder rod-end pivot pin (index #9). Use a soft metal drift to remove the pin. 52 Lower the cylinder onto the number 1 center pivot pin (index #13). 53 Attach a lifting strap from an overhead crane to the number 3 inner arm (index #24). 54 Remove the external snap rings from the number 3 pivot pin (index #10). 55 Use a soft metal drift to remove the number 3 pivot pin (index #10). Remove the number 3 inner arm (index #24) from the machine. Bodily injury hazard. The number 3 inner arm (index #24) may become unbalanced and fall if not properly supported when it is removed from the machine. 56 Attach a lifting strap from an overhead crane to the number 2 outer arm (index #27) at the ground controls side. 57 Use a soft metal drift to remove the number 2 center pivot pin (index #11) at the ground controls side. 58 Remove the external snap rings from the number 2 pivot pin (index #28) at the non-steer end of the machine. Do not remove the pin. 59 Use a soft metal drift to tap the number 2 pivot pin (index #28) halfway out at the non-steer end of the machine. Remove the number 2 outer arm (index #27) from the ground controls side of the machine. Bodily injury hazard. The number 2 outer arm (index #27) at the ground controls side may become unbalanced and fall if not properly supported when it is removed from the machine.
7 - 28
60 Attach a lifting strap from an overhead crane to the number 2 outer arm (index #27) at the battery pack side. 61 Remove the external snap rings from the number 2 center pivot pin (index #11) at the battery pack side of the machine. 62 Use a soft metal drift to remove the number 2 center pivot pin (index #11) at the battery pack side of the machine. 63 Use a soft metal drift to tap the number 2 pivot pin (index #28) in the other direction. Remove the number 2 outer arm (index #27) from the battery pack side of the machine. Bodily injury hazard. The number 2 outer arm (index #27) at the ground controls side may become unbalanced and fall if not properly supported when it is removed from the machine. 64 Use a soft metal drift to remove the number 2 pivot pin (index #28) from the machine. 65 Attach a lifting strap from an overhead crane to the number 2 inner arm (index #26). 66 Remove the external snap rings from the number 2 pivot pin (index #12) from the steer end of the machine. 67 Use a soft metal drift to remove the number 2 pivot pin (index #12). Remove the number 2 inner arm (index #26) from the machine. Bodily injury hazard. The number 2 inner arm (index #26) may become unbalanced and fall if not properly supported when it is removed from the machine.
68 Attach the strap from the overhead crane to the number 1 inner arm (index #14). 69 Using the overhead crane, lift the number 1 inner arm (index #14) approximately 2 feet (0.6 m). Place a 4x4x48 inch (10x10x122 cm) long block across both sides of the chassis under the number 1 center pivot pin (index #13). Lower the scissor arms onto the block. Bodily injury hazard. Keep hands clear of moving parts when lowering the arms onto the block. 70 Disconnect and plug the hydraulic hose on the lift cylinder. Cap the fitting on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 71 Tag and disconnect the wires from the solenoid valve on the cylinder. 72 Attach a lifting strap from an overhead crane to the lug on the rod end of the lift cylinder. 73 Remove the pin retaining fasteners from the lower lift cylinder barrel-end pivot pin (index #29). Use a soft metal drift to remove the pin. Remove the cylinder from the machine. Crushing hazard. If the overhead crane is not properly attached, the cylinder may become unbalanced and fall when it is removed from the machine. Component damage hazard. Be careful not to damage the valve or fittings on the cylinder while removing it from the machine.
7 - 29
74 Support and secure the entry ladder to an appropriate lifting device. 75 Remove the mounting fasteners from the entry ladder and remove the entry ladder from the machine. Crushing hazard. The entry ladder may become unbalanced and fall if not properly supported and secured to the lifting device. 76 Remove the cables from the number 1 inner arm (index #14) and lay them off to the side. Component damage hazard. Cables can be damaged if they are kinked or pinched. 77 Attach a lifting strap from an overhead crane to the number 1 outer arm (index #30). Do not lift it. 78 Remove the external snap rings from the number 1 center pivot pin (index #13). 79 Use a soft metal drift to remove the number 1 center pivot pin (index #13). Crushing hazard. The number 1 outer arm (index #30) may become unbalanced and fall if not properly supported when the pin is removed. 80 Slide the number 1 outer arm (index #30) to the non-steer end and remove it from the machine. Crushing hazard. The number 1 outer arm (index #30) may become unbalanced and fall if not properly supported when removing it from the machine. Note the position of the wear pads before the arm is removed so when the scissor is assembled they will be in the correct position.
81 Attach a lifting strap from an overhead crane to the number 1 inner arm (index #14). Do not lift it. 82 Remove the pin retaining fasteners from both of the number 1 pivot pins (index #15). Use a slide hammer to remove the pins. 83 Remove the number 1 inner arm (index #14) from the machine. Crushing hazard. The number 1 inner arm (index #14) may become unbalanced and fall if not properly supported when removed from the machine.
7 - 30
SCISSOR COMPONENTS
7 Lower the platform onto the safety arm. Crushing hazard. Keep hands clear of moving parts when lowering the arms onto the safety arm. 8 Mark the mounting position of the level sensor box on the drive chassis. 9 Remove the level sensor box lid. 10 Mark the mounting position of the level sensor on the level sensor box. 11 Remove the level sensor mounting fasteners. 12 Remove the fasteners from the level sensor box and slide the box towards the non-steer end of the machine as far as it can go. Component damage hazard. Be careful not to damage the level sensor box, limit switch, level sensor or wiring while moving the level sensor box. 13 Secure the ends of the scissor arms together at both ends of the machine with a tie down strap or other appropriate device. 14 Remove the pin retaining fasteners from the number 1 inner arm pivot pins (index #15) at the steer end of the machine. Use a slide hammer to remove the pins. 15 Attach a lifting strap from an overhead crane to the steer end of the scissor arms. 16 Carefully slide the forks from a forklift under the scissor arms at the non-steer end of the machine. 17 Raise the scissor arms up until the number 1 inner arm will clear the level sensor box. Component damage hazard. Be careful not to damage the level sensor box, limit switch or level sensor while moving the scissor assembly.
18 Move the scissor assembly towards the nonsteer end of the machine slightly and to one side of the machine until one of the scissor arm wear pads is accessible. Do not allow both wear pads to slide out of the drive chassis. Crushing hazard. The scissor assembly will fall if both wear pads are allowed to slide out of the drive chassis. 19 Install the new wear pad. Note the position of the wear pad before it is removed so when the new one is installed it will be in the correct position. 20 Move the scissor assembly towards the other side of the machine until the other scissor arm wear pad is accessible. Crushing hazard. The scissor assembly will fall if both wear pads are allowed to slide out of the drive chassis. 21 Install the new wear pad. Note the position of the wear pad before it is removed so when the new one is installed it will be in the correct position. 22 Slide the scissor assembly back into the drive chassis. 23 Lower the scissor assembly into position and install the pivot pins. Component damage hazard. Be careful not to damage the level sensor box, limit switch or level sensor while installing the scissor assembly.
7 - 31
SCISSOR COMPONENTS
3-4 Lift Cylinder How to Remove the Lift Cylinder GS-2046 & 2646
Bodily injury hazard. This procedure requires specific repair skills, lifting equipment and a suitable workshop. Attempting this procedure without these skills and tools could result in death or serious injury and significant component damage. Dealer service is strongly recommended. When removing a hose assembly or fitting, the O-ring on the fitting and/or hose end must be replaced and then torqued to specification during installation. Refer to Section Two, Hydraulic Hose and Fitting Torque Specifications. 1 Raise the platform approximately 7 to 8 feet (2.1 to 2.4 m). 2 Lift the safety arm, move to the center of the scissor arm and rotate down to a vertical position. 3 Lower the platform onto the safety arm. Crushing hazard. Keep hands clear of the safety arm when lowering the platform.
4 Tag and disconnect the wiring from the solenoid valve at the barrel end of the lift cylinder. 5 Disconnect the manual lowering cable from the solenoid. During assembly, the manual platform lowering cable needs to be properly adjusted. Refer to 4-1, How to Adjust the Manual Platform Lowering Cable. 6 Remove the mounting fasteners from the manual lowering cable mounting bracket. Remove the bracket from the cylinder. 7 Disconnect and plug the hydraulic hose from the lift cylinder. Cap the fitting on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 8 Attach a lifting strap from an overhead crane or similar lifting device to the rod end of the lift cylinder for support. 9 Remove the external snap ring from the lift cylinder rod-end pivot pin. Then use a soft metal drift to remove the pin. Crushing hazard. The lift cylinder may become unbalanced and fall if not properly supported. 10 Lower the cylinder to a horizontal position. If removing the lower lift cylinder, remove the entry ladder from the non-steer end of the machine.
7 - 32
SCISSOR COMPONENTS
11 Support and secure the entry ladder to an appropriate lifting device. 12 Remove the mounting fasteners from the entry ladder and remove the entry ladder from the machine. Crushing hazard. The entry ladder may become unbalanced and fall if not properly supported and secured to the lifting device. 13 Support the barrel end of the lift cylinder with a lifting device. 14 Remove the external snap ring from the lift cylinder barrel-end pivot pin. Then use a soft metal drift to remove the pin. Crushing hazard. The lift cylinder may become unbalanced and fall if not properly supported. 15 Carefully pull the cylinder out the non-steer end of the machine through the scissor arms. Component damage hazard. Be careful not to damage the valve or fittings on the cylinder while removing it from the machine.
7 - 33
SCISSOR COMPONENTS
6 Attach a lifting strap from an overhead crane or similar lifting device to the rod end of the lift cylinder for support. 7 Remove the external snap rings from the lift cylinder rod-end pivot pin. Then use a soft metal drift to remove the pin. Crushing hazard. The lift cylinder may become unbalanced and fall if not properly supported. 8 Lower the cylinder to a horizontal position. If removing the lower lift cylinder, remove the entry ladder from the non-steer end of the machine. 9 To remove the lower cylinder, support and secure the entry ladder to an appropriate lifting device. Then remove the mounting fasteners from the entry ladder and remove the entry ladder from the machine. Crushing hazard. The entry ladder may become unbalanced and fall if not properly supported and secured to the lifting device. 10 Support and secure the lift cylinder to an appropriate lifting device. 11 Remove the external snap ring from the lift cylinder barrel-end pivot pin. Then use a soft metal drift to remove the pin. Crushing hazard. The cylinder may become unbalanced and fall when it is removed from the machine if it is not properly attached and secured to the lifting device.
12 Carefully pull the cylinder out the non-steer end of the machine through the scissors arms. Component damage hazard. Be careful not to damage the valve or fittings on the cylinder while removing it from the machine.
Lift cylinder lowering valve coil specifications GS-3246 2 position 2 way N.C. solenoid valve - 20V (hydraulic schematic items Q and R) 23 - 259
7 - 34
Ground Controls
4-1 Manual Platform Lowering Cable, GS-2046 & GS-2646
The manual platform lowering cable lowers the platform in the event of a main power failure. The manual platform lowering cable is attached to the barrel end of the lift cylinder and is activated next to the ground controls. cable mounting bracket. Turn the lower lock nut clockwise to decrease the distance or counterclockwise to increase the distance. 8 Tighten the upper lock nut and re-measure the distance between the end of the lowering cable and the end of the lowering valve. Re-adjust if needed. 9 Install the cable mounting nut onto the lowering valve. 10 Raise the platform and rotate the safety arm to the storage position. 11 Pull the manual lowering handle at the ground controls 2 to 3 times to ensure it is functioning correctly.
Cable distance
3/16
c d
a manual lowering cable sheath b upper lock nut c cable mounting bracket d lower lock nut e cable mounting nut f end of the lowering cable g manual lowering valve (schematic item Q)
7 - 35
GROUND CONTROLS
7 - 36
Hydraulic Pump
5-1 Hydraulic Pump
The hydraulic pump is attached to the motor which makes up the Hydraulic Power Unit.
7 - 37
Manifolds
6-1 Function Manifold Components (before serial number 17482)
The function manifold is mounted inside the hydraulic power unit tray.
Index No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Description Schematic Item Function Torque
Flow regulator, 0.75 gpm (2.83 L/min) ....................... A ........... Steer circuit ....................................... 35-40 ft-lbs (47-54 Nm) Diagnostic nipple .............................. B ........... Testing .............................................. 10-12 ft-lbs (14-16 Nm) Orifice plug, 0.025 in (0.6 mm) .......... C ........... Brake circuit Orifice washer, 0.040 inch (1 mm) .... D ........... Steering circuit Relief valve, 1500 psi (103.4 bar) ..... E ........... Steering relief ................................... 25-30 ft-lbs (34-41 Nm) Relief valve, 3700 psi (255.1 bar) ..... F ........... System relief ..................................... 25-30 ft-lbs (34-41 Nm) 3 position 4 way solenoid valve ........ G ........... Steer left/right .................................... 18-20 ft-lbs (24-27 Nm) 2 position 4 way solenoid valve ........ H ........... Platform up ....................................... 23-25 ft-lbs (31-34 Nm) Orifice washer, 0.060 in (1.5 mm) ..... I ............ Brake circuit 2 position 2 way solenoid valve ........ J ............ Brake circuit ...................................... 18-20 ft-lbs (24-27 Nm) Check valve ....................................... K ........... Drive circuit ....................................... 35-40 ft-lbs (47-54 Nm) 2 position 4 way solenoid valve ........ L ........... Drive speed select circuit ................. 23-25 ft-lbs (31-34 Nm) 3 position 4 way solenoid valve ........ M .......... Drive forward/reverse ....................... 18-20 ft-lbs (24-27 Nm)
Important notes:
Schematic item E changed to 1500 PSI (103.4 bar) after serial number 3405 Schematic item C was deleted after serial number 8798 Schematic item J was deleted after serial number 8798 Schematic item A changed to 0.75 GPM (2.8 L/min) after serial number 11500 Schematic item K changed to 200 PSI (13.8 bar) after serial number 16893
Hex Size
5/16 9/16 5/8
7 - 38
MANIFOLDS
7 - 39
MANIFOLDS
Check valve ....................................... A ........... Steer circuit ....................................... 25-30 ft-lbs (34-41Nm) Diagnostic nipple .............................. B ........... Testing .............................................. 10-12 ft-lbs (14-16 Nm) Flow regulator, 0.75 gpm (2.83 L/min) ....................... C ........... Steer circuit ...................................... 35-40 ft-lbs (47-54 Nm) Orifice washer, 0.040 inch (1 mm) .... D ........... Steering circuit Relief valve, 1500 psi (103.4 bar) ..... E ........... Steering relief ................................... 25-30 ft-lbs (34-41 Nm) Relief valve, 3700 psi (255.1 bar) ..... F ........... System relief ..................................... 25-30 ft-lbs (34-41 Nm) 3 position 4 way solenoid valve ........ G ........... Steer left/right .................................... 18-20 ft-lbs (24-27 Nm) 2 position 4 way solenoid valve ........ H ........... Platform up ....................................... 23-25 ft-lbs (31-34 Nm) 2 position 2 way solenoid valve ........ I ............ Brake circuit ...................................... 18-20 ft-lbs (24-27 Nm) 2 position 4 way solenoid valve ........ J ............ Drive speed circuit select ................. 23-25 ft-lbs (31-34 Nm) 3 position 4 way solenoid valve ........ K ........... Drive forward/reverse ....................... 18-20 ft-lbs (24-27 Nm) Back presure relief valve .................. L ........... Drive circuit ....................................... 25-30 ft-lbs (34-41 Nm)
Hex Size
5/16 9/16 5/8
7 - 40
MANIFOLDS
7 - 41
MANIFOLDS
9 The power unit should not be able to lift the platform. If the power unit lifts the platform, adjust the internal hex socket counterclockwise until the platform will not raise. Tip-over hazard. Do not adjust the relief valve to allow the power unit to lift more than maximum rated load. 10 Install the relief valve cap. 11 Bleed the hydraulic system. Raise the platform to full height, and then lower it to the stowed position through two complete cycles. Result: If the pump cavitates or platform fails to reach full height, add hydraulic oil until the pump is functioning correctly. Do not overfill the hydraulic reservoir. Re-test the system by performing steps 8 through 11. Component damage hazard. Do not continue to operate the machine if the hydraulic pump is cavitating. If the pump is still cavitating, see 5-1, How to Test the Hydraulic Pump.
3 Turn the key switch to ground control and pull out the Emergency Stop button to the ON position at both the ground and platform controls. 4 Hold the system relief valve with a wrench and remove the cap (item #4, function manifold). 5 While activating the platform up function, adjust the internal hex socket clockwise to increase lift capacity or counterclockwise to decrease lift capacity. Adjust the relief valve until the platform just begins to raise. 6 Fully lower the platform. 7 Add an additional 100 pounds (45.4 kg) to the platform. Secure the additional weight. 8 Activate the platform up function.
7 - 42
MANIFOLDS
4 Turn the machine off. Hold the relief valve and remove the cap (item #6, function manifold). 5 Adjust the internal hex socket. Turn it clockwise to increase the pressure or counterclockwise to decrease the pressure. Then install the relief valve cap. Tip-over hazard. Do not adjust the relief valve higher than specified. 6 Repeat step 3 and re-check the valve pressure.
Drive relief valve specification Pressure 3700 psi 255.1 bar
6 Adjust the internal hex socket. Turn it clockwise to increase the pressure or counterclockwise to decrease the pressure. Install the relief valve cap. Tip-over hazard. Do not adjust the relief valve higher than specified. 7 Repeat steps 3 and 4 to confirm the steering relief pressure.
Steering relief valve specification Pressure 1500 psi 103.4 bar
7 - 43
MANIFOLDS
6-4 Lift Relief Valve, GS-3246 How to Adjust the Lift Relief Valve, GS-3246
Be sure that the hydraulic oil level is between the FULL and ADD marks on the oil level indicator decal. For machines manufactured before November 1999, contact the Genie Industries Service Parts Department and order a lift relief kit (Genie part number 66174). Install the kit, then complete the following procedure. For machines manufactured after October 1999, adjust the lift relief valve (schematic item M) using the following procedure. 1 Open the hydraulic power unit module tray and locate the lift relief valve located next to the function manifold. 2 Place maximum rated load into the platform. Secure the load to the platform.
Maximum Capacity GS-3246 ANSI & CE CSA 700 lbs 500 lbs 318 kg 227 kg
4 Hold the function relief valve with a wrench and remove the cap. 5 While activating the platform up function, adjust the internal hex socket clockwise to increase lift capacity or counterclockwise to decrease lift capacity. Adjust the relief valve until the platform just begins to raise. 6 Install the relief valve cap. 7 Fully lower the platform. 8 Add an additional 100 pounds (45.4 kg) to the platform. Secure the additional weight. 9 Activate the platform up function. 10 The power unit should not be able to lift the platform with the additional weight. If the power unit lifts the platform, remove the additional weight and repeat steps 4 through 9. Tip-over hazard. Do not adjust the relief valve to allow the power unit to lift more than maximum rated load. Result: If the pump cavitates or platform fails to reach full height, add hydraulic oil until the pump is functioning correctly. Do not overfill the hydraulic reservoir. Re-test the system by performing steps 8 through 11.
3 Turn the key switch to ground control and pull out the Emergency Stop button to the ON position at both the ground and platform controls.
7 - 44
MANIFOLDS
11 Bleed the hydraulic system. Raise the platform to full height and then lower it to the stowed position through two complete cycles. Component damage hazard. Do not continue to operate the machine if the hydraulic pump is cavitating. If the pump is still cavitating, see 5-1, How to test the Hydraulic Pump.
6-5 Back Pressure Relief Valve, GS-3246 How to Adjust the Back Pressure Relief Valve, GS-3246
Be sure that the hydraulic oil level is between the FULL and ADD marks on the oil level indicator decal.
1 Open the hydraulic power unit module tray and locate the lift relief valve located next to the function manifold. 2 Turn the machine off. Hold the back pressure relief valve with a wrench and remove the cap (item #12, function manifold). 5 Adjust the internal hex socket. Turn it clockwise to increase the pressure or counterclockwise to decrease the pressure. Then install the relief valve cap.
Lift Relief Valve Manifold, GS-3246 Models Description .................. Relief valve, 2000 psi (241 bar) Schematic Item ............................................................ M Function ........................................................ Platform up Torque ...................................... 25-30 ft-lbs (34-41 Nm)
7 - 45
7 - 46
6 Tag, disconnect and cap the hydraulic hoses on the drive motor. Cap the fittings on the drive motor. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 7 Support and secure the drive motor to an appropriate lifting device. 8 Remove the drive motor mounting fasteners, then remove the motor.
Torque specifications Castle nut 300 ft-lbs 406.7 Nm
7 - 47
7 - 48
7 - 49
Description
Torque
Check valve, pilot operated ............... N ........... Manual brake release ....................... 25-30 ft-lbs (34-41 Nm) Shuttle valve ...................................... O ........... Brake release ................................... 8-10 ft-lbs (11-14 Nm) Hand pump ....................................... P ........... Manual brake release ...................... 25-30 ft-lbs (34-41 Nm)
Hex Size
5/16 9/16 5/8
7 - 50
Distributed By:
Genie China
Phone: Fax: 86 21 62483040 86 21 62588180
Genie France
Phone: Fax: 33 237 260 999 33 237 260 998
Genie Japan
Phone: Fax: 81 3 3453 6082 81 3 3453 6083
Genie Holland
Phone: Fax: 31 7051 78836 31 7051 13993
Genie UK Limited
Phone: Fax: 44 1636 605030 44 1636 611090