TALAT Lecture 3501

Alloys and Properties

8 pages, 6 figures

Basic Level

prepared by Klaus Siegert and Manfred Kammerer, Institut für Umformtechnik,

Universität Stuttgart

Objectives:

− To provide a background on aluminium alloys suitable for impact extrusion

− To draw attention to raw material parameters which may affect the properties of
impact extruded parts

Prerequisites:

− Basic knowledge about the formability of metals

− Background in mechanical engineering

Date of Issue: 1994

 EAA- Euro p ean Aluminium Asso ciatio n
3501 Alloys and Properties

Table of Contents:

3501 Alloys and Properties ..................................................................................2

3501.01 General Information on Alloys and Raw Materials ................................ 2
Aluminium Alloys for Impact Extrusion .................................................................2
Reference Values for the Strength of Aluminium Alloy Impacts............................3
Flow Curves and Fow Stresses ................................................................................4
Raw Materials, Blanks and Slugs ............................................................................5
Lubricants ................................................................................................................5
Tool Life as a Function of Amounts of Lubricant ...................................................6
3501.02 Literature: ................................................................................................... 8
3501.03 List of figures............................................................................................... 8

3501.01 General Information on Alloys and Raw Materials

Aluminium Alloys for Impact Extrusion

Figure 3501.01.01 lists the different types of aluminium alloys used for impact
extrusion together with an evaluation considering different aspects. All aluminium
alloys of the non-heat-treatable and heat-treatable types can be impact extruded,
especially when in their soft annealed state. (See also DIN 1712, part 3 and DIN 1725,
part 1).

TALAT 3501 2
 Aluminium Designation Relative merit values1) under various aspects
according to Impact Decorative Joining Remarks
Alloys DIN 1712, p.3 extrud- anodising process3)
and ability 2)
for Impact DIN 1725, p.1
S L

Extrusion Pure and high purity aluminium (DIN 1712, part3)

Aluminium alloys
Al99.5 1 2 2 1 Main material for impacts
for impact
Al99.7 1 2 2 1
extrusion
1)
Al99.8 1 1 2 1
Merit values,
falling from 1 to 4; Al99.9 1 1 2 1 Chemical brightening possible
"-" = not suitable Non-heat-treatable alloys (DIN 1725, part 1)
2)
Valuation is valid
for the original soft AlMn 2 - 2 1
annealed state AlRMg0.5 2 1 2 2 Chemical brightening possible
3)
S = weldability; AlMg1 2 2 2 2
L = suitability for AlMg3 4 2 1 -
brazing.
AlMg2Mn0.3 3 3 1 -
Strength loss due
to welding and Heat-treatable alloys (DIN 1725, part 1)
soldering must be AlMgSi0.5 2 1 2 3
considered! AlMgSi1 3 2 2 3
AlZn4.5Mg1 3 - 2 - Used only in artificially aged state
Source: Aluminium AlCuMg1 4 - - - Only for parts with heavy wall thickness
-Zentrale e.V. AlZnMgCu0.5 4 - - - which are used only in an aged state

alu

Training in Aluminium Application Technologies

Aluminium Alloys for Impact Extrusion 3501.01.01

In order to obtain high quality impacts, it is important to use materials which exhibit a
homogeneous fibre structure or a uniform fine-grained structure. A non-homogeneous
structure affects not only the chemical and physical properties of the impacts but also
their form. An unsymmetrical grain structure can have a large effect on flow stress
which in turn might lead to excentricity of the part, warpage or uneven distribution of
wall thicknesses.

Reference Values for the Strength of Aluminium Alloy Impacts

Figure 3501.01.02 tables reference values for the strength of aluminium alloy impacts.
The aluminium alloys Al99,9, Al99,8. Al99,7 and Al99,5 are mainly used for
manufacturing tubes and cans. The alloys AlMgSi0,5 and AlMgSi1 can be considered to
be standard materials for impact extrusion. Care must be taken during the machining of
the alloys AlZn4,5Mg1 and AlZnMgCu0,5, since the emulsions used can lead to
corrosion.

TALAT 3501 3
 Reference
Designation State Strength in N/mm² Elongation
Values for Rm (σB) Rp0.2 (σ0.2) A5 (%)
the Strength Al99.5/ annealed 70 25 40
Al99 impact extruded 130 110 6
of Impacts Al99.7/ annealed 60 18 40
Al99.8 impact extruded 120 100 4
Attainable 40
Al99.9 annealed 40 15
mechanical properties, impact extruded 100 80 4
not minimum values AlMn annealed 90 35 24
impact extruded 170 145 4
1)
By impact extruding AlRMg0.5 annealed 80 25 23
directly after solution impact extruded 140 110 4
AlMg1 annealed 105 35 24
treatment and quenching
impact extruded 165 145 4
("freshly quenched" state)
AlMg3 annealed 190 80 20
and then aging, 90% of impact extruded 265 215 4
the strength of the AlMg2Mn0.3 annealed 155 60 20
state "artificially impact extruded 230 200 4
aged" can be attained. AlMgSi0.5 annealed, imp. extr. 165 145 4
1) artificially aged 245 195 10
AlMgSi1 annealed, imp. extr. 190 170 4
1) artificially aged 310 260 10
AlZn4.5Mg1 artificially aged 350 290 10
AlCuMg1 naturally aged 400 350 10
AlZnMgCu0.5 artificially aged 500 450 7
Source: Aluminium-Zentrale e.V.

alu

Training in Aluminium Application Technologies

Reference Values for the Strength of Impacts 3501.01.02

Flow Curves and Fow Stresses

Figure 3501.01.03 shows flow curves and flow stresses of some aluminium alloys (at
left) and the effect of state of heat treatment of AlMgSi1-slugs on the flow behaviour (at
right). Flow curves are needed for the calculation of forces for the impact extrusion
process. For further flow curves, refer to the VDI guideline 3500.

Flow Curves and Flow Stresses

Flow curves for various annealed Flow stress as a function of
aluminium alloys at room temperature heat treatment state of the slug

600 State: annealed 600 Artificially aged

ϕ = 5 x 10 s
-4 -1

N/mm² N/mm² Naturally aged

AlMg3
Flow stress, kf

Flow stress, kf

400 400
AlCuMg
Hot worked
AlMgSi(Mn)
200 200 Soft
Al99.5
AlMgSi1
RT
0 0
0 1 2 3 0 1 2 3
True strain ϕ True strain ϕ
Source: J.Hardt Source: H.G.Roczyn

alu
Flow Curves and Flow Stresses 3501.01.03
Training in Aluminium Application Technologies

TALAT 3501 4
Raw Materials, Blanks and Slugs

Figure 3501.01.04 gives information regarding the manufacturing of slugs and blanks,
their required surface condition and their properties. Cold rolled sheets and rods or tubes
from which blanks and slugs are obtained by blanking or sawing, respectively, are
standardised in DIN 1745, part 1 and DIN 59604. Round rods of pure aluminium or
aluminium alloys are extruded with so-called multiple extrusion dies, i.e. three or four
die openings are arranged around the centre of the die. In a final step these rods are cold
drawn to size and final dimensions. Since the material is pressed through the multiple
die not only from the centre portion of the billet but also from its outer areas, such round
rods may exhibit different grain sizes in any one cross-section. As a result, impact
extruded parts can warp in unexpected amounts and wall thicknesses may vary.
Therefore, care should be exercised, that only single-strand extruded rods are taken as
base material for slugs and blanks.

Raw Materials; Blanks and Slugs

Manufacturing raw materials
The raw material consists almost exclusively of stamped or sawed blanks
and slugs available from extruders or stockists

Surface condition of raw material

Blank, ground, tumbled, blasted

Requirements of raw material

! The weight of blanks or slugs is allowed to vary only within a narrow
tolerance range
! Minimum clearance between slugs and die: 0.3 to 0.4mm
! Maximum tolerance for round slugs and blanks is h11 (larger deviations in
diameter lead to positioning errors)
! A uniform grain size. Varying grain size can lead to variations in dimensions

Source: Schlosser; Brix

alu

Training in Aluminium Application Technologies

Raw Materials; Blanks and Slugs 3501.01.04

Lubricants

Figure 3501.01.05 lists the different lubricants used and the methods of applying them.
Because of environmental considerations, water-soluble lubricants like alkalinen soaps
and liquid lubricants based on oil are being increasingly used. Zinc stearate and zinc
behenate have nowadays to compete with
− Lubrimet GTT (Sapilub Ltd. Co. Wangen, Zurich) based on paraffin without
chlorinated solvents and heavy metal soaps with optimal solubility in water,
− Glisapal SM-155 (Nußbaum Co., Matzingen), a water-soluble, solvent-free,
powdery lubricant based on alkaline soaps, not suitable for anneal degreasing and
solvent cleaning,

TALAT 3501 5
 − and liquid lubricants based on oil, like Bonderlube VP 4404/5 (Chemetall Co.,
Frankfurt), with sulphur compounds, but free from chloroparaffins and metal
organic compounds or
− Multipress 9391 (Zeller and Gmelin Co., Eislingen), a fully synthetic oil.

In individual cases, coating layers serving as carriers for lubricants (aluminium,

phosphate) are used.

Lubricants
Lubricants used

! Zinc stearate and zinc behenate (insoluble in water)

! Alkaline soaps (water soluble)
! Liquid lubricants based on oil (water soluble)

Methods of applying lubricants

! Spraying
! Coating
! Sprinkling, powdering
! Dipping
! Tumbling

Source: D.Schlosser

alu

Training in Aluminium Application Technologies

Lubricants 3501.01.05

Tool Life as a Function of Amounts of Lubricant

Figure 3501.01.06 illustrates the influence of amount of lubricant used (g/m²) on tool
life. As can be clearly seen, too little or too much lubrication reduces the tool life. If the
lubricant used is insufficient, cold welding can occur between tool and work-piece. If
too much lubricant is used, then the lubricant accumulation leads to defects in contour
replication and to lubricant indentations in the tool. In these cases, the tool has to be
cleaned very often. The surface roughness of slugs and blanks has an effect on the tool
life. Experiments have shown that smooth slugs reduce the life of tools because the
smooth slug surface offers hardly any cavities and pits in which the lubricant can be
anchored.

TALAT 3501 6
 Tool Life as a Function of Amounts of Lubricant

Cold Contour
welding defects
failure optimum failure

Tool life

Relative lubricant amount in g/ m²

Source: D.Schlosser

alu

Training in Aluminium Application Technologies

Tool Life and Lubricant Amounts 3501.01.06

TALAT 3501 7
3501.02 Literature:

1) F.Ostermann: Technische Kaltfließpreßteile aus Aluminium. In seminar volume

"Gestalten und Fertigen von technischen Fließpreßteilen aus Aluminium", Institut
für Umformtechnik, Universität Stuttgart, 15.-16. June, 1992

2) D.Schlosser: Einflußgrößen auf das Fließpressen von Aluminium und

Aluminiumlegierungen und ihre Auswirkung auf die Weiter- und
Fertigbearbeitung der fließgepreßten Rohteile. In seminar volume "Gestalten und
Fertigen von technischen Fließpreßteilen aus Aluminium", Institut für
Umformtechnik, Universität Stuttgart, 15.-16. June, 1992

3) D.Brix: Kaltfließpressen von Leichtmetall - Qualität und Wirtschaftlichkeit. Draht

1975/5, p. 216-219

4) VDI-Richtlinie 3138: Kaltfließpressen von Stählen und Nichteisenmetallen,

Grundlagen, part 1. Beuth-Verlag, Berlin, 1970

5) Aluminium-Zentrale e.V., Report No. 29 "Aluminium für technische

Fließpreßteile", Düsseldorf, 1982

3501.03 List of figures

Figure No. Figure Title (Overhead)

3501.01.01 Aluminium Alloys for Impact Extrusion
3501.01.02 Reference Values for the Strength of Impacts
3501.01.03 Flow Curves and Flow Stresses
3501.01.04 Raw Materials; Blanks and Slugs
3501.01.05 Lubricants
3501.01.06 Tool Life and Lubricant Amounts

TALAT 3501 8