Vogel Pompen P PVa
Vogel Pompen P PVa
Vogel Pompen P PVa
Vogel Pumpen
Handled liquids:
Pure as well as slightly contaminated media such as: hot and cold water condensate oil suspensions acids as well as their watery solutions caustic solutions brine
Sizes:
DN 80 up to DN 300 (from 3 to 12) discharge
Pumpenfabrik ERNST VOGEL has developed and manufactured multistage pumps since 1910. Our application and manufacturing expertise provide you with the BEST SOLUTION to meet your pumping needs.
Modular system:
The entire performance range is covered by 7 mechanical sizes that hold 9 different hydraulics.
Size
Discharge branch DNd [mm] 80 100 125 150 200 250 250 300 300
Suction branch DNs [mm] 100 125 150 200 250 300 300 400 400
Capacity at BEP Q [m3/h] 6 0 Hz 140 200 300 500 790 900 1100 1) 1)
P, PVa 84 P, PVa 104 PA, PVa 124 PA, PVa 154 P, PVa 204 P 253 P 254 MP 300.1 MP 300.2
1) upon request
Hydraulics:
Sizes 84-254, closed radial type impellers designed for casing wear ring on bolth sides. Axial thrust minimized by balance holes for minimum bearing loads and a maximum bearing liftetime. Size MP 300.1 and MP 300.2 thrust balanced by a balancing drum. Size 84-104 P: one piece design for diffusor and casing. Size 124 PA-254 P and MP 300.1, 300.2: two piece design for diffusor and casing. Balanced radial forces, minimum shaft deflection, minimum vibrations.
All design versions acc. to ISO 5199 / EN 25199. ISO 9001 certification guarantees high quality standards and reliability of our products.
Performance range - 60 Hz
1750 r.p.m.
Type PVa:
Vertical design with separate thrust bearing and flexible coupling between motor and pump. Standard IEC motors, up to 315 kW.
Type PT
Vertical wet pit configuration length: max. 10 m - 1450 / 1750 r.p.m. Inducer design available.
Sectional drawing page 8
Horizontal configuration with outer bearings on both sides. Driven by electric motors, combustion engines or steam turbines, via flexible coupling. Drive side discharge, clockwise rotation (drive side suction and counter clockwise rotation available). Branch directions: suction left viewed from drive end, discharge radially upwards. Branches can be adjusted to meet customer requirements in 90 o increments. Drive side thrust bearing, two angular contact ball bearings. Suction side roller bearing as floating bearing. Oil lubrication with large capacity oil sump. Thermal expansion of the pump rotor will be balanced internally without affecting the shaft alignment. Shaft sealing arrangements (mechancial seal or gland packing) see pages 9 and 10. Maintenance friendly design. Bearings and shaft seal are maintainable without pump disassembly.
Type PVa:
Vertical configuration with a separate thrust bearing. Grease lubricated with grease nipples. Standard motor according to IEC, design V1, up to 315 kW Flexible coupling between pump and motor Medium lubricated sleeve bearing in suction casing Maintenance friendly design. Bearings and shaft seal are maintainable without pump disassembly.
Vertical wet pit design Installation length: 1450/1750 r.p.m. - max. 10 m Separate grease lubricated thrust bearing with grease nipples Standard motors according to IEC, design V1 Flexible coupling between pump and motor Drive and discharge branch always above liquid level Medium lubricated sleeve bearings in pump body and shaft section. Number of bearings depending on installation length Suitable for variable speed control Mechanical seal or gland packing available Maintenance friendly design Suction bells, suction strainers or foot valves available Can design available when pumping hot or volatile media Inducer design available for low NPSH applications when pumping volatile and warm liquids
For more detailed information about operation limits with regard to material configuration and operation conditions please refer to data sheets or actual quotations.
Gland packing:
10
Standard materials N SN VN VV NL VL NF VF 0.6025 CC480 K 1.4408 1.4408 0.6025 1.4408 0.6025 1.4408 0.6025 0.6025 0.6025 1.4408 0.6025 0.6025 0.6025 0.6025 0.6025 0.6025 0.6025 1.4408 0.7040 0.7040 1.0619 1.0619 0.6025 0.6025 0.6025 1.4408 Material options 0.7040 0.7040 1.0619 1.0619 0.7040 0.7040 1.0619 1.0619
1) 1) 1) 1)
1) 1) 1)
1.4462
Elastics (O-rings) EPDM for hot water up to 140 o C, optional VITON (Pay attention to operation limits and chemical resistance) Temperature and pressure operating limits depending on the material version, please refer to techn. data sheets.
Kohle 1)
Application limits regarding pressure, temperature and speed as well as chemical resistance refer to data sheets or actual quotations. Optional materials upon request.
11
Vogel Pumpen
Pumpenfabrik ERNST VOGEL GmbH A-2000 Stockerau Ernst Vogel-Strae 2 Telefon: ..43-2266-604 Telefax: ..43-2266-65311 E-Mail: info@vogel.itt.com
Liability of manufacturer and/or supplier The mentioned limits of operation and/or application are only a general information and may not be applied for every case. The permitted range of operation and/or application for the specific case is to be obtained from our acknowledgement of order and/or the instructions for installation, operation and maintenance, sent with the goods.
www.vogel-pumpen.com
Liste 2300.1.B
9/2007-e
12