Renderoc Laxtra

R
e
n
d
e
r
o
c

L
A
X
t
r
a
constructive solutions Fosr oc Render oc LAXt r a
Shrinkage controlled, polymer modified, fluid
microconcrete for structural repairs of all types
Uses
Renderoc LAXtra is suitable for mass infill to structural repairs
in all types of load bearing situation. Typical applications would
include, but not be limited to, the following :
! Repairs to columns suffering from major loss of section
! Soffit repairs where heavy load bearing is required
! Repairs to restricted access areas, where use of hand
applied mortars would prove impractical
! Repairs requiring high fluidity e.g. heavily congested steel
or repairs into re-entrant angles/concealed voids
! Any repairs requiring significant levels of loadbearing
Advant ages
Renderoc LAXtra features Dimensional Stability Technology
- a new materials technology which controls the rate of drying
shrinkage such that, when used correctly :
i. the dimensions of the repair remain stable; and thus
ii. eliminating failure, due to shrinkage cracking.
This in turn leads to a series of associated benefits :
! Cost effective - shrinkage control enables repairs to be
completed right first time
! Enhanced durability - works in tandem with extremely low
permeability to prolong effective working life
! Compatibility - aligns performance closer than ever before,
to that of host concrete
! User friendly - specifically developed to provide an easy-
to-apply product, suitable for local conditions
! Definable performance - positive benefits are easily
demonstrated via a single, simple measurement
Desc ri pt i on
Renderoc LAXtra is supplied as a ready to use blend of dry
powders and selected aggregates, which requires only the
addition of clean water to produce a highly consistent, fluid
microconcrete suitable for all load-bearing situations.
Pr oper t i es
The following typical results were obtained at a water:powder
ratio of 0.135
Test method Typical result
Drying shrinkage to ASTM C157-93
7 days :< 300 microstrain
28 days :< 500 microstrain
Permeability :< 10 mm
(DIN 1048 Part 5)
Flexural strength :> 9 N/mm
2
at 28 days
(BS 6319 Pt.3)
Tensile strength :> 5 N/mm
2
at 28 days
(BS 6319 Pt.7)
Compressive strength :> 39 N/mm
2
at 3 days
(BS 1881 Pt.116
1
) > 45 N/mm
2
at 7 days
> 60 N/mm
2
at 28 days
Water absorption :< 2%
(BS 1881 Pt. 122)
Note1: 100mm cubes, air cured @ 20
0
C
Desi gn c r i t er i a
Dimensional Stability Technology is a major step forward in
the general compatibility of repair mortar systems with the
host concrete, and the control of shrinkage in particular.
Attention to the basic design criteria given below should ensure
that the full benefits of this technology are gained in use :
(i) Renderoc LAXtra is designed for large volume repairs,
typically in excess of 50 mm deep. The product can be
applied in sections generally between 50 and 200 mm
thick, greater thicknesses may be achievable, depending
upon repair configuration and location together with the
volume of reinforcing steel.
Consult the local Fosroc office for more information.
(ii) In situations where a substrate/repair barrier is required,
or enhanced bond strength/working time is required, or
where the substrate is likely to be damp (e.g. seawalls,
quays etc.), Nitobond EP epoxy bonding agent should be
used.
(iii) Water addi ti on = 3.38l trs / 25kg bag Under no
circumstances should part bags be used or additional
water be employed. Either of these two actions will
adversely affect material performance, automatically
invalidating Fosrocs standard product guarantee.
UAE/0253/06/J
Fosr oc Render oc LAXt r a
Al Gur g Fosr oc LLC
Post Box 657, Dubai
United Arab Emirates
w w w.f osr oc .c om
I mpor t ant not e
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for
the Supply of Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the users responsibility to
obtain the latest version.
Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
Regional offices
Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com
Qatar, Tadmur telephone: 4432365 fax: 4419517 email: qatar@fosroc.com
See separate data sheet

Gal vani c Pr ot ec t i on of r epai r s
It is likely that, steel reinforcement in the area around a patch
repair, particularly in a chloride contaminated environment,
will typically corrode after the repairs are carried out, referred
to as the incipient anode or Halo effect.
Gal vashi el d XP*
(eXtra Protecti on) anodes can be

incorporated into patch repairs to galvanically protect steel
reinforcement against corrosion in the adjacent concrete and
may also be used in new construction to provide Cathodic
Prevention. Galvashield XP are zinc based anodes encased
in a highly alkaline mortar which maintains the surface of the
zinc in an active state. Galvanic systems are self regulating
and demand based and will start working only when corrosion
of steel begins. Refer to product datasheet for further details.
I nst r uc t i ons f or use
Renderoc LAXtra should be mixed and applied in strict
accordance with the Product Method Statement, a copy of
which may be obtained from your nearest Fosroc office.
Est i mat i ng
Supply
Renderoc LAXtra : 25kg bags
Yield
Renderoc LAXtra : 12.25 ltrs per 25kg bag
Li mi t at i ons
- Renderoc LAXtra should not be used when the ambient
temperature is below 5C and falling.
- Renderoc LAXtra should not be part mixed, nor part bags
used.
- Renderoc LAXtra should not be exposed to running water
either during application or prior to final set.
- Water ponding is not recommended for curing.
St or age
Shelf life
Renderoc LAXtra has a shelf life of 12 months if kept in a dry
environment, in its original packing. If stored in conditions of
high temperature and/or humidity, the shelf life may be
reduced to as little as 4 months.
St andar ds c ompl i anc e
Renderoc LAXtra repair microconcrete system complies with
the following international standards :
ASTM C157-93 : Test for drying shrinkage
DIN 1048 Part 5 : Test for permeability
BS 1881 Pt. 121 : Water absorption
Pr ec aut i ons
Health and safety
Renderoc LAXtra contains cement powders which, when mixed
with water or upon becoming damp, release alkalis which can be
harmful to the skin.
During use, avoid inhalation of the dust and contact with the skin or
eyes. Wear suitable protective clothing - eye protection, gloves and
respiratory equipment (particularly in confined spaces).
The use of barrier creams to provide additional skin protection is
also advised. In case of contact with the skin, rinse with plenty of
clean water, then cleanse thoroughly with soap and water.
In case of contact with eyes, rinse immediately with plenty of clean
water and seek medical advice. If swallowed seek medical attention
immediately - do not induce vomiting.
Fire
Renderoc LAXtra, is non-flammable and thus presents no
fire hazard.
For further information, please refer to the Product Material
Safety Data Sheet for Renderoc LAXtra.

Renderoc Laxtra

Uploaded by

Copyright:

Available Formats

Renderoc Laxtra

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Renderoc Laxtra

Uploaded by

Copyright:

Available Formats

R

See separate data sheet

(eXtra Protecti on) anodes can be

You might also like