Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

BOQ-CIVIL Sample Lucknow

Download as xls, pdf, or txt
Download as xls, pdf, or txt
You are on page 1of 25

A)

B) Samples of all materials will have to be approved by EIC before use.


C)
PART A COMPOUND WALL / CULVERT/KERB WALL
Line
no.
Description Unit RATE
SITE CLEARANCE
Surface dressing of the ground including removing trees of
girth upto 30cm, (measured at a height of 1M above ground
level), vegetation and making surface levelled and disposal of
rubbish outside HPCL's premises to an unobjectionable
place, within a radius of 1 KM as directed by the Engineer in
Charge.
3 FELLING OF TREES : Felling of trees of the girth upto
120cm( measured at a height of 1 M above ground level)
including cutting of trucks and branches removing the roots
and stacking of serviceable material and disposal of
unserviceable material withn a radius of 5 KM.
EACH 450
EXCAVATION
Excavation for foundation upto required depth below existing
ground level in any type of soil except hard rock . Rate to
include dressing the sides and bottom, bailing out of water if
encountered, shoring, strutting, backfilling after the
construction of foundation, compacting by the side of the
foundation and disposal of surplus excavated earth
within/outside HPCL's premises to an unobjectionable place
within a radius of 5 KM, as directed by the Engineer in
Charge including spreading, watering and compaction,
complete
4 Up to 1.5 mtr depth CUM 80
5 Below 1.5 mtr and upto 3 mtr depth CUM 100
6 Below 3.0M and upto 4.5 meters CUM 120
EXCAVATION IN HARD ROCK
Description same as item no.2.0 except that soil will be hard
rock and excavation shall be done by chiselling.
7 For 0-1.5 Mmtr depth CUM 380
8 Above 1.5 mtr and upto 3 mtr depth CUM 500
SAND FILLING
Supply and filling with clean locally available approved
quality sand in layers of 150 mm each including
compacting by hand ramming and watering.
Mesaurement shall be on comacted volume and no Provision
for bulking etc shall be allowed.
PCC WORK :
PCC 1:3:6FOR FOUNDATION
Providing and laying PCC 1:3:6 using 40 mm and down size
graded stone aggregates including machine mixing, providing
formwork if required, placing, compacting by hand ramming
, curing etc complete.
PCC 1:2:4 FOR DPC
Providing and laying 40 mm thick DPC in 1:2:4 mix with
graded stone aggregate of nominal size 12.5 mm mixed with
and water proofing compound ( impermo or equivalent) at
the rate of 1 kg per bag of cement .
PCC 1:2:4 FOR COPING/ grouting MS rolled section
Providing and laying 60 mm average thickness coping in CC
1:2:4 mix using garded stone aggregates 12.5mm
Nominalsize with 40 mm projection on either side of wall with
drip mould. Rate to include 20 mm thick plaster in CM 1:4
including mixing, providing necessary shuttering,
compaction and curing. Thickness of coping at the ends shall
be 40 mm and 80 mm at centre .
REINFORCED CEMENT CONCRETE
SCHEDULE OF RATE FOR MODERNISATION OF RETAIL OUTLETS
UNDER RANCHI REGIONAL OFFICE

11 SQM 150
12 CUM 3120
9 CUM 325
10 CUM 2400


Quoted rate shall be applicable for any height, depth, level and thickness of wall etc
unless otherwise specified. Sales Building shall be generally ground floor and G+1 in
some cases.
List of approved make / brand is attached to technical / commercial bid. Decision of
HPCL with regard to selection of make/brand of material to be used shall be final.
All jobs to be carried out as per technical specification attached to
technical/commercial bid. All IS Codes referred to shall be of Latest Edition .
2 SQM 2
Providing , mixing and placing RCC 1:1.5:3 mix with
ordinary Portland cement using 20 mm and down size
graded crushed aggregate including providing and fixing
necessary plywood /steel shuttering ,scaffolding, machine
mixing, compacting by vibrators, curing , hacking the
surface to receive plaster etc. complete. Rate shall be
exclusive of the cost of steel reinforcement, which will be paid
under a separate item. Concrete shall conform to relevant
specifications of IS 456 Latest Edition.
13 FOOTINGS/PILE CAPS CUM 3840
14 COLUMNS/BEAMS CUM 3960
15 CULVERT SLAB CUM 3960
16 PRECAST CONCRETE BLOCKS CUM 4080
UNDER REAMED PILES
Providing RCC 1:1.5:3 for under reamed piles up to
required depth with double bulbs as per IS 2911 etc. All
complete. Reinforcement steel shall be paid separately. Pile
cap shall be paid separately.
17 300mm dia pile RMT 750
18 230mm dia pile RMT 650
REINFORCEMENT STEEL
Supply ,fabrication , hoisting and placing in position HYSD/
TMT reinforcement bars conforming to IS 1786 of
SAIL/TISCON/RISPNL make as per detailed drawing and
specifications including cutting, bending and tying with 18
SWG binding wire complete. The rates shall be applicable for
all heights and depths. Payment shall be made as per
reinforcement drawings and with theoretical weights only
including all authorised laps and hooks.
BRICK MASONRY WORKS
Providing and constructing following brick masonry in CM
1:4 using first quality bricks of Class designation 50
(minimum50kg/sqcm)conforming to IS-1077-1986 including
providing all openings and projections , raking the joints to 1
cm deep, scaffolding, soaking of bricks in water prior to use
and curing etc complete as per specifications .
SUB STRUCTURE
Providing and laying brick masonry as above for foundation
below DPC level.
SUPER STRUCTURES.
Providing and laying brick Masonry as above for
superstructure 230mm or more above DPC level including
scaffolding.
22 Pointing inBrick masonry: Flush pointing inBrick work with
1: 3 CM
SQM 42
Providing and constructing random rubble masonary with
good quality stone in CM 1:5 for substructure &
superstructure as per IS 1597 part 1, latest edition Rate to
include raking the joints to 1 cm deep , providing through
stones @ 2m c/c and curing etc. complete.
23 SUBSTRUCTURE CUM 1150
24 SUPERSTRUCTURE including scaffolding CUM 1200
RUBLE PITCHING
Providing 230mm thick rubble pitching including surface
dressing, making required slope . Rate to exclude flush
pointing which will be paid separately .
POINTING
26 Providing flush pointing in rubble pitching with 1:3 cement
mortar including curing etc. complete.
SQM 40
27 Providing 12mm raised pointing in RR masonary wall with
1:3 cement mortar including curing etc. Complete.
SQM 55
PLASTERING
Providing and laying average 15 mm thick sand faced cement
plaster in single coat in CM 1:4 fine sand.
-Rate shall include providing necessary scaffolding, chicken
wire mesh at all joints of brick and concrete surfaces, with a
minimum overlap of 150 mm in all directions and curing
complete. No extra payment shall be made for additional
thickness if required to achieve perfect line and level.
WATER PROOF CEMENT PAINT (SNOWCEM) 29 SQM 30
25 SQM 250
28 SQM 65
20 CUM 2100
21 CUM 2280
19 MT 45000


Providing and applying 2 coats of snowcem water proof
cement paint snowcem plus to plastered and concrete
surfaces including providing necessary scaffolding, surface
preparation etc. complete. If additional coats are required to
obtain uniform and smooth finish, the same shall be carried
out at no extra cost.( application rate minimum 3.84 Kg/10
SQM)
WEEP HOLES
Providing, and installing in place, 75 mm dia PVC Pipe of
approved make of various lengths & at places with back
filter( with coarse aggregates as directed at site on the
masonry wall for water drainage.The pipes shall be fixed with
nylon jali using resin/glue on inside end of the wall.
CHAIN LINK FENCING /BIRBED WIRE FENCING
PIPE RAILING :
Supply and fixing of 40 NB medium quality MS pipes
conforming to IS 1239 latest addition for top and bottom
railings to the angle iron posts for fixing the edges of the
chain link fencing. Rate to include fabricating, cutting,
bending of the MS pipe where ever necessary. Supply and
fixing of the required size MS clamps at every post, with
required size nuts and bolts and painting the railing with two
coats of Zinc Phosphate Primer and two coats of Synthetic
enamel paint after necessary cleaning and scrapping . Paint
and primer used shall be of SHALIMAR/ BERGER/ASIAN
Make first quality only.
CHAIN LINK FENCING :
Supply and fixing of 50 x 50mm opening size 10 SWG GI
chain link fencing to the angle iron post with 8 SWG GI
hooks and nuts and railing with 14 SWG GI continuous wire
(all details shall be as per enclosed drawing ) up to a height
of 1.8 m from the ground level. Rate to include unrolling the
bundle, erecting, tightening and fixing at 300 mm C-C on
the vertical portion of the posts to every top and bottom
railing with 14 gauge GI wire.
BARBED WIRE FENCING
Providing and fixing 13 rows horizontal and two diagonals
with two ply 12 SWG GI barbed wire fencing with barbes @
100mm c/c . Angle iron post shall be paid separately. For
payment purpose measurement shall be taken for the lenth
of plot boundary . No measurement shall be taken for 13
rows individually.
34 GRATINGS/GRILLS/STAIRCASE/STRUCTURAL STEEL:
Providing ,fabricating ,fixing in position of with steel rolled
sections/MS tubular sections as per drawing given by
HPCL.Rate to include erection grouting of gratings in PCC(
PCC shall be sepataely paid), painting with two coats of
synthetic enamel paint over two coat of red oxideprimer.
KG 55
HUME PIPE
Supplying, laying, joining and aligning 1000mm NB NP2
class RCC Hume pipes conforming to IS-458 Latest Edition
below approach road whereever directed. Rate to include
joining with cement mortar, excavation up to required depth
and providing and laying PCC 1:2:4 haunching @ 1m c/c .
Test certificates from manufacture shall be submitted and
approved by EIC before use.
REINFORCED CONCRETE JALI : Providing , fixing in
position upto a height of 3 M above ground level., cement
concerete Jali of approved pattern in 1:2:4 ( 1cement : 2
coarse sand: 4 graded stone aggregates 6mm nominal size
with 1.6 mm dia mild steel wire including centering,
shuttering, roughening claening, fixing and finishing in
cement mortar 1:3 ( 1cement: 3 fine sand) etc. Complete
exluding plastering of jambs, sills and soffits.
36 50mm thick SQM 260
37 40mm thick SQM 220
PART B SALES BUILDING/CANOPY FOUNDATION
EXCAVATION
Excavation in any type of soil excluding hard rock for
foundation, plinth beam, trenches etc. Including dressing the
sides and bottom, bailing out water if encountered, shoring,
strutting, backfilling and compacting the excavated earth in
the sides of foundations. Rate to include carting away
surplus excavated earth, spreading, levelling and
compacting, inside or outside the HPCL premises to an
unobjectionable place within 5 KM radius as directed by
Engineer-In-Charge.
38 Upto 1.5 M depth CUM 80

33 RMT 135
35 RMT 4500
31 RMT 250
32 SQM 180
29 SQM 30
30 RMT 200
39 Below 1.50 m and upto 3.0 M depth CUM 100
40 Below 3 mtr and upto 4.5 mtr depth CUM 120
Same as above but excavation of hard rock by chiselling
41 Up to 1.5m depth CUM 380
42 Below 1.5m and up to 3m depth CUM 500
ANTI TERMITE TREATMENT
Providing anti-termite treatment including diluting and
injecting Neem base solution and creating a continuous
barrier under and alround the column pits, wall trenches,
basement excavation, top surface of plinth filing, junction of
wall and floor, along the external perimeter of building,
expansion joints, over the top surface of consolidated earth
on which apron is to be laid, surroundings of pipes and
conduits etc. Complete as per specification using Neem
based solution. Plinth area of building at ground floor only
shall be measured for payment.The work shall be carried out
by a qualified agency and 10 years guarantee to be given.
MURRUM FILLING
Supplying and filling approved quality Murrum in layers of
200 mm thick including watering and compacting with 8-10
MT power Roller till maximum compaction is achieved as
directed by Engineer In Charge.Compacted volume shall be
considered for payment.
SAND FILIING
Supplying and filling locally available good quality river sand
in layers of 150 mm thick including watering and compacting
till maximum compaction is achieved as directed by Engineer
In Charge.Compacted volume shall be considered for
payment.
RUBBLE SOLING
Providing and laying 230mm thick rubble soling including
hand packing, filling the interstices with chips, spalls and
binding with grit and selected murrum, watering, compacting
by hand ramming.
47 BRICK FLAT SOLING : Providing and laying 75 mm thick
brick flat soling including hand packing, filling the
interstices with chips, spalls and binding with grit and
selected murrum, watering, compacting by hand ramming.
SQM 132
PLAIN CEMENT CONCRETE
Providing and laying PCC of following mix including
providing and fixing form work, machine mixing, compaction
and curing etc complete as per specification.
48 PCC 1:3:6 mix using 40 mm and down size graded crushed
aggregates below flooring, plinth protection etc.
CUM 2400
PCC 1:2:4 for DPC
Providing and laying 50 mm thick DPC in PCC 1:2:4 mix
with 6 to 12 mm size aggregate and water proofing
compound at the rate of 1 kg per bag of cement.
REINFORCED CEMENT CONCRETE 1:1.5:3
Providing and laying RCC 1:1.5:3 concrete for following
works using 20 mm and down size graded crushed
aggregate including providing and fixing necessary steel/ply
shuttering, scaffolding, machine mixing, compacting by
mechanical vibrators, curing,etc complete. Concrete shall
conform to IS 456-Latest edition Rate shall be excluding the
cost of steel reinforcement , which will be paid under a
separate item.
50 Footings/ pile cap CUM 3840
51 Pedestals,Columns , plinth beams, floor beams, lintel CUM 3960
52 Roof Slab, Chhaja, staircase CUM 3960
UNDER REAMED PILES
Providing RCC 1:1.5:3 for under reamed piles up to
required depth with double bulbs as per IS 2911 etc. All
complete. Pile cap and reinforcement steel shall be paid
separately.
53 300mm dia pile RMT 750
54 230 mm dia pile RMT 650
STEEL REINFORCEMENT 55 MT 45000
49 SQM 180

46 SQM 250

44 CUM 300
45 CUM 325
43 SQM 50
Supplying, fabricating, and placing in position HYSD/TMT
reinforcement bar conforming to IS 1786 grade FE 415
including cutting, bending & supply and binding with 18
SWG annealed binding wire. Payment shall be made as per
reinforcement drawings and at theoretical weights only.
Measurement of chairs, spacers and laps will not be
considered for payment.
BRICK MASONARY
Providing and constructing brick masonry in CM 1:4 using
bricks having minimum compressive strength 50 Kg/cm2
and conforming to IS: 1077- Latest Edition including
providing all openings and projections as per the drawing,
raking the joints to 1 cm deep, scaffolding, soaking of bricks
prior to use and curing etc complete as per specifications .
230 mm & above thickness in walls/foundations
SUB STRUCTURE
Providing and laying brick masonry as above for foundation
below DPC level.
SUPER STRUCTURES.
Providing and laying brick Masonry as above for
superstructure 230mm or more above DPC level including
scaffolding.
58 115 mm thick in partition walls in CM 1:4. Rate to include
providing 75 mm thick RCC 1:2:4 bands using 2 nos 8 mm
dia Torsteel reinforcement at every 1 M height of wall
including shuttering. Steel reinforcement shall be paid for
separately.
SQM 260
PLASTERING
SAND FACED PLASTER (EXTERNAL)
Providing and laying average 18 mm thick sand faced cement
plaster as per following procedure :
Apply 12 mm thick coat of CM 1:4 mixed with CICO/
IMPERMO/ ACCOPROOF/Sikacim M water proofing
compound mixed as per manufacturer's specifications as 1st
coat and leaving the surface rough.
Apply 2nd coat of 6 mm thick of CM 1:3 and finishing the
surface by rubbing with sponge till uniform texture is
obtained.
Rate shall include providing necessary scaffolding, chicken
wire mesh at all joints of brick and concrete surfaces, with a
minimum overlap of 150 mm in all directions and curing
complete.
SMOOTH CEMENT PLASTER FOR CEILING/CHHAJA
Providing and applying 6 mm thick plaster in CM 1:3 to
ceiling and bottom surface of chajja using screened fine
sand including finishing smooth and providing drip moulds
at chajja edges, scaffolding and curing etc. complete.
SMOOTH CEMENT PLASTERING (INTERNAL WALL)
Providing and laying 15mm thick smooth cement plastering
in 1:4 CM in single coat to all the interior walls including
providing necessary scaffolding, chicken wire mesh at all
joints of brick and concrete surfaces, with a minimum
overlap of 150 mm in all directions and additional thickness
if required to achieve perfect line and level without any extra
cost.
CERAMIC TILE FLOORING
Providing and laying matt finish 1st quality Ceramic floor
tiles of conforming to IS 13755 thickness to be specified by
the manufacturer) of following size in flooring of approved
make and shade and free from cracks, warpage,fissures and
flakes with straight edges and perfect corner laid at right
angle as per design and pattern over a bedding of cement
mortan of 30 mm thick CM 1:4 finishing the joints neatly
with white cement mixed with matching colour pigment and
finish in all respect and all material and labour complete.
62 395mmx395mm SQM 700
63 300mmx300mm SQM 650
64 SAME as in 12 but with vitrified ceramic tile flooring using
300 mmx 300mm or higher size approved by EIC(basic rate
not below Rs 600/- )
SQM 1100
IPS FLOORING

65 SQM 220
60 SQM 50
61 SQM 65
57 CUM 2280
59 SQM 75

56 CUM 2100
55 MT 45000
Providing mixing and laying 52 mm thick Indian Patent
Stone flooring with hardcrete concrete hardener toping
under layer 40 mm thick 1:2:4 mix concrete with 20mm and
down size graded crushed aggregate and top layer 12mm
thick hard crete cement hardener consisting of mix 1:2( 1
harderner mix : 2 stone agreegates 6 mm nominal size ) by
volume with hard crete hardening compound of Snowcem
India Ltd or equivalent is mixd a@ 2l hardcrete per 50 Kg of
cement including providing and fixing glass strips in
1 metre x 1 metre panels, casting the concrete compacting
and finishing the surface smooth using cement slurry.
SKIRTING
Providing and fixing granite/marble/ceramic tiles in
skirting of 125 mm height free from crack fissures & flakes
with straight edges & perfect corners fixed at right angles
with neat cement paste and finishing the joint with white
cement mixed with matching colour pigment .Rateto include
all necessary chippingof brick masonry /concrete and using
CM 1:3 and as directed by EIC :
66 With 10mm polished black jet granite RMT 160
67 With 10mm Marble skirting RMT 140
68 With Kota stone 18 mm skirting RMT 105
69 With ceramic tiles 8mm thick RMT 90
70 With polished vitrified ceramic tiles 8mm thick(base rate not
below Rs600/SQM
RMT 150
CERAMIC TILES DADO IN TOILET:
Providing and fixing ceramic tiles of 200x 300 mm size or
as directed by EIC of approved shade and make First
quality , free from crack fissures & flakes with straight edges
& perfect corners at right angles as per the design and
pattern, including applying 12mm thick backing plaster in
1:4 CM and fixing the tiles with neat cement paste , and
finishing the joints with white cement mixed with colouring
pigments to match the colour of tiles properly cured &
finished in all respects, etc complete
18 MM THICK GRANITE CLADDING FOR CURTAIN WALL
Providing and fixing machine cut and polished black Granite
slab of thickness of 18 mm and 1 SQm approx selected &
sorted for uniformity in colour, free from cracks, fissures and
flakes with straight edges and perfect cornors using
50mmx20mmx3mm SS T shaped cleats of 100mm long . The
cleats are fixed over the wall with M12x100mm long GI
fasteners by providing 2 nos 12mmx25mm size slots and
drilling the wall. Rate to include making necessary grooves in
granite slab , finishing the joints neatly with white cement
mixed with coloring pigment to match color, polished and
finished in all respect, all materials and labour complete.
Fixing of HPCL supplied LOGO of size 5 x 4 or 4 x 3 shall
be done at no extra cost. The deduction for the logo part on
actual basis shall be made in mesurement of the granite
cladding of curtain wall.
KOTA STONE FLOORING/STEPS / PATHWAYS
Providing and fixing 20 mm thick green Kota stone slabs
and with 25mm bedding CM 1:3, cement slurry and
machine polishing on one side for risers of steps, treads and
shelf slab etc( upto 1SQM) as directed by EIC) including
nosing etc . complete
74 MARBLE FLOORING/STEPS : Providing and laying
marble flooring with 18 mm thick Doongri or approved
equivalent marble upto 1 SQM(base rate not lower than Rs
600/-) over 20mm average thick base of CM(1:4 1 cement
and 4 coarse sand)laid and joint with white cement slurry
with matching pigments etc complete. Marble sample to be
approved by EIC
SQM 1100
SILL SLAB
Providing and laying 20 mm thick machine cut & machine
polished jet black granite strips over a bedding of 20 mm
thick 1:4 CM for window sills. The strips shall be of single
piece only as per width of window wall and project 12 mm
beyond the face of the wall.
WATER PROOFING
TERRACE
Providing and laying integral cement based water proofing of
average 100 mm thick as per specifications given below:
75 SQM 2200
76 SQM 300
72 SQM 2450
73 SQM 600
71 SQM 525
65 SQM 220
- cleaning RCC slab and applying neat cement slurry
mixed with waterproofing compound.( sika raintite or
equivalent aprroved)
- providing and laying brickbat coba in CM 1:4 mixed
with water proofing compound and curing for a period of 24
hours.
- laying of 25 mm thick PCC 1:1.5:3 mix with 6 mm and
down size coarse aggregate and water proofing compound
conforming to IS 2645, finishing smooth , making half round
vata at the junction of parapet wall and slab and curing for
10 days.
Contractor will be required to submit a guarantee in respect
of performance of waterproofing for 10 years on stamp-paper.
In addition to this, an amount equal to 10% of cost of
waterproofing items shall be retained as retention money for
2 years from the date of completion(in the form of
bankgurantee or DD), which shall be returned only after
successful completion of this period.
77 Water proofing on top of chhaja with 25mm thick PCC
1:1.5:3 with 6mm and down size stone aggregate mixed with
water proofing compound(Sikaraintite or equivalent
approved), finishing smooth, making half round vata at the
junction of chhaja and wall , curing etc. complete.
SQM 150
PAINTING
WHITEWASH
Providing and applying 3 coats of white wash to plastered
and concrete surfaces including providing necessary
scaffolding, surface preparation , mixing DDL binder, blue
etc. complete as per IS: 712- Latest Edition. If additional
coats are required to obtain uniform and smooth finish, the
same shall be carried out at no extra cost.
OIL BOUND DISTEMPER
Providing and applying 2 coats ( first coat with brush and
final coat with Roller) of OBD of approved make and shade
on all surfaces and heights to give an even shade including
primimg coat and full putty after thoroughly brushing the
surface free from mortar dropping and other foreign matter
and also including preparing the surface even and sand
papered smooth etc., all material and labour complete
ACRYLIC EMULSION PAINT (INTERIOR GRADE)
Providing and applying 2 OR MORE coats ( first coat with
brush and final coat with Roller) of Acrylic Emulsion paint of
approved make and shade on all surfaces and heights to
give an even shade including primer and full putty after
thoroughly brushing the surface free from mortar dropping
and other foreign matter and also including preparing the
surface even and sand papered smooth etc., all material and
labour complete
80 SQM 70
78 SQM 6
79 SQM 40
76 SQM 300
ACRYLIC EMULSION PAINT (EXTERIOR GRADE)
Providing and applying 2 coats of acrylic anti fungal cement
paint including primer of BERGER (Weathercoat) or approved
equivalent make and shade to all the exterior surfaces over a
coat of primer as per manufacturer's specifications
including providing necessary scaffolding, curing , etc.
complete. If additional coats are required to obtain uniform
finish, the same shall be carried out at no extra,cost as
directed by Engineer In Charge.
WATER PROOF CEMENT PAINT
Providing and applying 2 coats of water proof cement paint
of SNOWCEM INDIA make and of required shades on all
surfaces and heights to give an even shade after thoroughly
brushing the surface free from mortar dropping and other
foreign matter and also including preparing the surface even
and sand papered smooth etc., all material, scaffolding and
labour complete. (application rate minimum 3.84 Kg/10
SQM)
SANDTEX MATT
Providing and applying 2 coats@3.28 L/10SQM of Sandtex
matt paint of SNOWCEM INDIA make and of required
shades on all surfaces and heights to give an even shade
including a primer coat of snowcem plus @ 2.2Kg/10 SQM
after thoroughly brushing the surface free from mortar
dropping and other foreign matter and also including
preparing the surface even and sand papered smooth etc., all
material, scaffolding and labour complete
SYNTHETIC ENAMEL PAINT OVER WALL
Providing and applying 2 coats of synthetic enamel paint 1st
quality of approved manufacturer and of required shades on
wall to give an even shade including a primimg coat after
thoroughly brushing the surface free from mortar dropping
and other foreign matter and also including preparing the
surface even and sand papered smooth etc., all material ,
scaffolding and labour complete
SYNTHETIC ENAMEL PAINT OVER STEEL SURFACE
Providing and applying 2 coats of synthetic enamel paint
1st quality of approved manufacturer and shades on steel
surface to give an even shade including two coats of red
oxide primer after thoroughly brushing the surface free from
rust and other foreign matter and also including preparing
the surface even and sand papered smooth etc., all material
and labour complete
86 PLASTER OF PARIS : Providing and applying plaster of
paris punning on WallS and Ceilings, beams complete. The
rate shall include preparing the surface with POP and
compatible putty( Upto2mm approx) to give a smooth finish
as approved by EIC. Rate shall include cost of scrapping,
neeru finish etc complete.
SQM 55
DOORS, WINDOWS, VENTILATORS
87 ALUMINIUM GLAZED DOOR/ FIXED GLAZING WITH
12MM GLASS:
SQM 3000
Providing and fixing Aluminium glazed door/ fixed glazing
with 15 micron coloured anodised(ILKA or approved
equivalent) aluminium section minimum wall thickness of
not less than 2 mm with extruded built up section of
approved make and weight ratio joints mitred joint with
heavy duty aluminium pressure die cast cleats with fins to
match the section of frames conforming to approved section
and shutter conforming to approved sections and glazed with
12 mm thick glass fixed to shutter with aluminium snap
beading and neoprene / PVC gaskets/CP brass/stainless
steel screws and fixed to the wall with requisite rawl plugs
and screw or with fixing clips or with expansion hold fastners
including necessary filling up of gaps at junctions, at top ,
bottom and sides with requisite PVC/neoprene
felt/polysulphide sealant/sillicon sealant etc all complete as
per architectural drawing.
84 SQM 60
85 SQM 60
82 SQM 30
83 SQM 80
81 SQM 75
Aluminium anodised shop front ( Doors/fixed glazing ) with
frames at top & bottom and at ends(if end sections are not
used for door at theoption of EIC , Hindalco section No. SP-
2670 of 88 x 42 x 2.3 with wt 2.927 kg/m in thiscase to be
used) of INDAL make or equivalent with section no. 9205 of
size 101.5 x 44.45x 3 with weight of 2.342 kg/m .Round
acrylic handle and locking arrangement to be provided for
main door. Alternately, for fixed glazing Hindalco section No.
SP-2670 of size 88 x 42 x 2.3 @ 2.927kg/m for top and
bottom and Hindalco section SP 730 of size 63.5 x 38x 3 with
wt 1.55 kg/m or approved equivalent at two ends and fixing
cleats / chips of Hindalco section No.SP-1778 of size 17.15 x
17.27 x 1.4 @ 0.175 kg/m without any vertical AL sections at
joints.The intermediate joints spacing shall be 3mm machine
cut in true linelevel and plumb. No harizontal jonts is
permitted in Glazing. The vertical spacing between the galss
piece shall be treated with silicon sealant to stop ingress of
water. Galss surface shall be thoroughly cleanedneat of left
over sealant. Approved makes for glass are AIS/saint gobin/
Modi.
88 Same as above but with powdercoating of Aluminium
sections in place of Annodising.
SQM 2875
HYDRAULIC FLOOR SPRINGS
Providing and fixing double action hydrauclic floor springs of
approved brand ( HARDWYN/EVERITE) conforming to
IS:6315 for aluminium doors. Rate to include cutting of
floors as required, embeding in floors and cover plates etc
complete as per specifications.
ALUMINIUM PANELLED DOOR
Providing and fixing 15 micron colored anodised(ILKA or
equivalent approved) single leaf aluminium door with
minimum wall thickness of not less than 2 mm, joints
mitred jointed with heavy duty aluminium pressure die cast
cleats with fins to match the section of frames conforming to
INDAL section 9221 or equivalent section
(Jindal/HIndalco)and shutter conforming to INDAL section
9200, 920, 9202 and 9240 or equivalent section
(Jindal/Hindalco) , fully panelled with 9 mm thick
prelaminated 3 layers midium density ( exterior grade)
particle board Grade-1, type -II conforming to IS:12823
bonded with phenolformaldehyde synthetic resin of approved
brand and manufacturer fixed to shutter with aluminium
snap beading and neoprene / PVC gasket / CP Brass
/stainless steel screws fixed to the wall with requisite rawl
plugs and screw or with fixing clips or with expansion hold
fastners including necessary filling up of gaps at junctions,
at top, bottom and sides with requisite PVC/neoprene
Aluminium door section of INDAL make or equivalent make
as per EIC with the following section :
Main frame on all sides - 9221 -101.5 x 44.45 x 2.5 of weight
1.975 kg/mtr
Shutter vertical frame- 9202 - 50 x 44.5 x 2.5 of weight
1.202 kg/mtr.
Shutter top frame - 9201-50x44.5x2.5 of weight 1.299
kg/mtr
Shutter middle frame - 9129-50x45x2.5 of weight 1.292
kg/mtr
Shutter bottom frame - 9200-100x44.5x2.5 of weight 1.974
kg/mtr
Door handle -5140 - 100x 30 x 2.5 of weight 0.988 kg/mtr
Glazing clip - 4660 - 17.8 x 17.6x 1.3 of weight 0.169 kg/mtr
ALUMINIUM WINDOWS
ALUMINIUM WINDOWS (OPENABLE)
Providing and fixing 15 micron colour anodised(ILKA or
equivalent approved) aluminium glazed windows with 4 mm
glass & extruded built up section of wall thickness not less
than 1.5 mm and approve make with glass panel fixed to side
-hung shutter with aluminium snap beading and neoprene
/ PVC gasket / CP Brass /stainless steel screws fixed to the
wall with requisite rawl plugs and screw or with fixing clips
or with expansion hold fastners including necessary filling up
of gaps at junctions, at top , bottom and sides with requisite
PVC / neoprene felt / polysulphide sealant/sillicon sealant
including heavy duty handle cum locking arrangement etc all
complete as per architectural drawing and the direction of
Engineer In-charge.
Aluminium door section of INDAL make or equivalent
(Hindalco/Jindal) make with the following section :
Outer frame - 2082 -34 x 44.45 x 28.5x 2 of weight 0.554
Kg/mtr
Shutter frame- 4124 - 34 x 44.5 x 28.5x 1.5 of weight 0.494
kg/mtr
Mullion -9139- 57 x 34 x 25x2 of weight 0.810 kg/mtr
Cleat angle - 2081 - 50 x 50 x 4.9 of weight 1.177 kg/mtr
Glazing clip : 4125 - 31x 17.5 x 1.2 of weight 0.184 kg/mtr
92 Same as above but Aluminium sliding windows with two/
threetracks.
SQM 2400
ALUMINIUM LOUVRED VENTILATOR
Providing and fixing colour anodised(ilka or equivalent)
aluminium ventilator with extruded built up section of wall
thickness not less than 1.5 mm and approve make glazed
with 4 mm thick opaque glass louver 100mm wide .
ALUMINIUM DOOR/FIXED GLAZING WITH 6MM GLASS
93 SQM 2000
94 SQM 2500
90 SQM 2600
91 SQM 2200
89 NOS 1450
Providing and fixing 25 micron coloured anodised(ILKA or
equivalent) aluminium fixed glazing/aluminium door with 6
mm glass extruded built up section of wall thickness not
less than 1.5 mm and approved make with glass panel
fixed with Aluminium snap beading/ Neoprene / PVC
gasket/CP Brass /stainless steel screws and fixed to the wall
with requisite rawl plugs and screw or with fixing clips or
with expansion hold fastners including necessary filling up of
gaps at junctions, at top , bottom and sides with requisite
PVC / neoprene felt / polysulphide sealant/sillicon sealant
all complete as per architectural drawing and the direction
of Engineer In-charge.
Aluminium section of INDAL make or equivalent make with
the following sections :
Outer frame - 2082 x 34x 44.5 x 28.5 x 2 of weight 0.554
kg/mtr
Mullion - 9139 - 57 x 34x 25 x 2 of weight 0.810 kg/mtr
Cleat angle - 2081- 50 x 50 x 4.9 of weight 1.177 kg / mtr
Glazing clip- 4125- 31 x 17.5 x 1.2 of wt. 0.184 Kg/mtr
Bottom 900mm height shall be with 9mm thick both side
prelaminated NOVOPAN board. The door shall be provided
with aluminium handle, towerbolt, locking arrangement etc.
complete.
STEEL WINDOWS
Supply, fabrication and fixing of MS glazed windows using
approved Z sections with 4mm plain glass including
providing grill with 12mm square bar @100mm c/c ,
painting with two coats of red oxide primer and two coats of
synthetic enamel paint, handle , stay arrangement etc.
complete.
96 Steel Doors : Providing , fabricating and fixing of MS door
using 35 x 35x 5 angle frame and 25 x25 x3 angle members
including bracings with 16 gauge MS sheet stich welded to
door shutter frame complete as per direction of Site- in
charge painting with two coats of synthetic enamel paint over
two coats of red oxide primer,handle stay arrangement tower
bolt etccomplete.
SQM 1750
ROLLING SHUTTER
Supply, fabrication and fixing of MS rolling shutter of the
following specifications (including grill window of 300 mm
height or without the grill as per EIC )at eye level for visibility
even in closed position.
Code: Conforming to IS 6248 1979
Type: Self Coiling type (manual)
Curtains: Interlocking cold rolled lath section of 0.8 mm
thickness.
Lock plate : MS sheet of 3.15 mm thick reinforced with MS
angles of 35 x 35 mm.
Guide channel : MS sheets of 3.5 mm thick
Bracket Plate : MS Sheet of 0.9 mm thick
Hood Covers : MS sheet of 0.9 mm thick
Locking handle : To be provided suitably.
Rate shall include providing and fixing holdfasts and
painting two coats of enamel paint of approved make and
shade over two coats of zinc phosphate primer. For area of
the rolling shutter exceeding 10 SQM upto 35 SQM
mechanical operatd gear type with ball bearing shall be
provided at no extracost.
98 Grill in Rolling Shutter : Supply , fabrication and fixing of
manually operated Steel rolling shutter as per specification ,
nets in hexagonal pattern made out of 8 mm MS round bars
. All other specification asper item No.30
SQM 1900
DISPLAY SHELVING/STORAGE
DISPLAY SHELF
Providing & fixing in position 12 mm thk plain galss of Modi
Guard/ Asahi make with polished edges in the grooves
between the 25 mm thick exterior grade MDF board planks
at 375 mm c/c & 300 wide. The vertical members of the MDF
planks are at every 1200 mm c/c or as per drawing The
exposed surface of the MDF board shall be finished with 1.5
mm thick lamination of approved colour & combination of
colours with teak wood beadings on edges. The approved
brand for the lamination shall be
Formica/greenlam/Sundek. The shelf shall be movable type
fixed with wheels. Storage and shelves shall be with 25mm
MDF board
99 SQM 3300
95 SQM 2000
97 SQM 1850
94 SQM 2500
MISCELLANEOUS
100 Providing & fixing MS fan hooks with 16 mm dia MS bar bent
to shape with hooked ends in RCC Slab during laying
including painting the exposed portion
Nos 50
MORTICE LOCK
Providing & fixing GODREJ or equivalent make six lever lock
( Cylindrical/ Round Head ) including all necessary hardware
etc.
DOOR CLOSER
Providing and fixing door closer of Hardwin/Everite make
size no. 2
103 STRUCTURAL STEEL WORK FOR SERVICE BAY MT 55000
Supplying , erecting and fixing in position Pre- fabricated
structures at all elevations for service bay using structural
steel sections conforming to IS:2062 , including cutting,
welding or bolting, supply of bolts/nuts/washers etc.,
complete as per drawings including surface preparation and
applying two coat of Zinc Phosphate epoxy Primer before
erection and two coats of coaltar epoxy paint as per
specification after erection and all materials and labour
complete. ( No welding is permitted at site). The rate quoted
shall include cost of bolts, nuts, washers, welding and
electrodes and any other consumables required for
completing the work.
Supply , erection and fixing of corrugated asbestos cement
sheet of Everest / Charminar make or approved equivalent
for service bay including supply and fixing of bitumen/GI
washer, J bolt etc.
104 For roof SQM 315
105 For side sheet including gable end SQM 350
GYPSUM BOARD FALSE CEILING
Providing and fixing Gyp board (12.5 thick)false ceiling with
required accessories INDIA GYPSUM make or equivalent
approved, including painting with two coats of plastic
emulsion paint
PLUMBING AND SANITARY WORK
EUROPEAN TYPE WATER CLOSETS
Supplying and fixing coloured (pastel colour) vitreous china
European type water closet comprising of the the following
accessories including cutting and making good the walls &
floors wherever required compleste as directed by Engineer In
Charge
A) Coloured ( pastel colour) viterous china pedestal type
European water closet with P or S trap of Hindware
sanitaryware standard model or equivalent approved make
as per the direction of Engineer In Charge.
B) 15mm NB brass angle valve as per ISI of approved brand
as per the direction of Engineer In Charge
C) 15 mm NB CP inlet connection with Brass unions at the
ends.
D) Commander make or equivalent matching colour
polypropylene seat cover with necessary brass hinges and
rubber bushes etc
E) WC connector with neoprene rubber etc
F) 10 litres capacity low level plastic cistern of matching
colour parry slimline make or approved equivalent with
necessary fittings, brackets, screws, etc all complete.
INDIAN WATER CLOSET
Supplying and fixing coloured (pastel colour) vitreous china
Orissa Pan type water closet comprising of the the following
accessories including cutting and making good the walls &
floors wherever required complete as directed by Engineer In
Charge
A). Coloured (pastel colour) viterous china 580 mm orissa
pan water closet of Hinduatn sanitaryware or any equivalent
make with P or S trap
B) 10 litres capacity hi-grade engineering plastic low level
flushing cistern of matching colour parry slimline
make , model no 8068 or approved equivalent make with
necessary fittings, brackets , screws etc. all complete
C) 32 mm PVC flush pipe 10Kg/sq.cm quality of approved
length with necessary fittings, clamps etc
D) 15 mm NB CP inlet connections with brass union at the
ends
107 NOS 3000
108 NOS 2800
102 NOS 850
106 SQM 800
101 NOS 850
E) 15mm NB brass angle valve as per ISI of approved brand
as per the direction of Engineer In Charge
F) WC connector with neoprene rubber.
URINALS
Supplying and fixing coloured (pastel colours) viterous china
flat back urinal of size 300mmx400mm with integrated
overflow of Hindustan Sanitary or equivalent approved make
with CP flush valve, cp pipe connection, CP waste coupling ,
CP Brass bottle trap, 32 mm PVC waste line of required
length etc. all complete as per the direction of Engineer In
Charge
URINAL DIVISION PLATE
Providing and fixing 1200 x 450 x 18 mm size granite
partition plate between urinals including cutting
masonary/concrete surface to required size, fixing the
division plate on the ceramic tiles by means of SS clamps,
nuts & bolts, polishing all exposed surface etc all complete
as directed by Engineer In Charge.
111 URINAL FLUSH VALVE
Supply and fixing Urinal flush valve of Jaquar Make,
Sensotronic concealed type flush valve 51077 model of
approved colour. Job includes necessory supply of flushing
valve for urinal complete set with installation box with
control cock, making necessory plumbing connections with
all suitable supply of accessories, testing, making necessory
power / battery connections as per manufacturers
recommendation to suit Hindware urinal model no. 60006
Olumpus Half stall urinal etc., all complete material, labour
all as per HPCL EIC directions.
NOS 13500
112 HAND WASH BASIN NOS 2200
Providing and fixing coloured (pastel colours) wash basins of
size 550 x 400 without pedestal Including the following
accessories:
-15mm brass CP Jaquar make (Cat.no.093) stop cock -1 No .
-15mm CP connections from the above stop cock to pillar
cock - 1 No.
-32mm dia waste coupling, CP brass chain and rubber
stopper.
-30mm bottle trap Jaquar make with cleaning eye, extension
piece and wall flange.
-Providing and fixing brass CP Jaquar make 13mm half turn
pillar cock.(Cat. no.011)
Rate to include supply, painting and fixing of necessary CI
brackets with nuts and bolts and fixing the wash basin with
all necessary connections in walls.
MIRROR
Providing and fixing bevelled edge mirror of superior belgium
glass or equivalent of 5.5 mm thick & 600 x 600 mm size of
approv ed make, 3mm thick felt backing or 6 mm asbestos
sheet or with wooden beads allround of specified size and
fixed with wooden plugs with CP brass screws and cup
washers etc all complete as directed by Engineer In Charge .
SOAP TRAY
Providing and fixing readymade CP brass soap tray near
wash basin with CP brass screws of approved make.
115 LiQUID soap dispenser : Providing and fixing liquid soap
dispensers having refillable system and transparent view of
container showing reamaing soap level. Care shuld be
takenm that tiling is not damaged during installation. Make -
Euronics technocrat/ Akson
NOS 650
116 TOILET PAPER HOLDER NOS 250
Supplying and fixing of 150 x 150 mm pastel coloured toilet
paper holder of Hindustan Sanitary ware or equivalen
approved make with paper at required position and elevation
as directed. Rate to include making good the chases in walls
after fixing the above.
117 TOWEL RAIL NOS 400
Providing and fixing CP brass towel rail of 20 mm dia and
600 mm long including all accessories such as brackets
(coloured), fixed and anchoring etc. complete as directed.

118 GRAB BAR NOS 3000.0
113 NOS 600
114 NOS 200
109 NOS 1600
110 NOS 1500
108 NOS 2800
Supply, fabricating, welding, fixing in position approved
make SS pipe / SS tube / SS plate grade TP304,(JINDAL OR
APPROVED MAKE) as per drawing made out of 40mm dia
Stainless Steel pipe 2mm wall thk. and 8mm SS rod, plates,
screws. Job includes necessary fixing with as per drawings,
specifications, HPCL EIC directions.
119 HEALTH FAUCET NOS 1100.00
Providing and fixing Health Faucet of model No. HYGI
SPRAY T9929GI of Parryware or equivalent of Hindware.
All Complete as directed.
120 WALL HUNG WASH BASIN NOS 4500.00
Providing and fixing coloured wash basins wall hung type
with pedastal of make Basin CTH 048 and pedastal 0375 of
Parryware or Basin 10008 Viking and pedastal 11002 of
Hindware including the following accessories. -Providing and
fixing CP Parko make Pillar cock of No 1536 - swan neck. -
All other fittings like waste coupling, botle trap, stop cock
range of fittings shall be classic line collection from PARKO.
121 AUTOMATIC HAND DRYER: Providing, fixing and
commissioning fully automatic hand dryer i.e. autostart on
positioning the hand and autostop. Care shall be taken so
that tiling is not damaged while installation. Rate includes
PVC insulated power chord having copper conductor and
Anchor ROMA make 3 pin power plug matching ampere load
of instrument. Make - Technocrats (Model Alpha AP-800) or
Euronics (Model CYC 30) or equivalent.
NOS 8000.00
STOP COCKS AND BIB COCKS
Providing and fixing in position CP brass stop cocks and bib
cocks of heavy type ISI marked of approved make.
122 15mm dia stop cocks NOS 300
123 15mm dia bib cocks NOS 300
124 15mm dia angle cocks NOS 300
CONCEALED GI PIPING
Providing & fixing following size medium grade GI pipes of
TATA/ JINDAL make conforming to IS-1239 concealed in the
walls and under the concrete floors including making chases
in the walls or concrete floors,fixing with clamps at every 1m
c-c, necessary tees, bends, elbows, plugs, nipples, unions,
testing of pipelines for leaks upto a test pressure specified
by EIC , painting the pipes with hot bitumen, wrapping the
pipes with hessian cloth and making chases of the walls
good after piping complete.
125 15 mm nominal bore RMT 110
126 20 mm nominal bore RMT 130
127 25 mm nominal bore RMT 165
EXPOSED GI PIPING
Description same as above but Providing, laying and fixing
GI medium grades pipes in open on brick or RCC surface
with the help of MS U clamps at every 1 m and at every
turn.
128 15 mm nominal bore RMT 100
129 20 mm nominal bore RMT 120
130 25 mm nominal bore RMT 150
Rgid PVC pipes for both exposed and concealed piping
ASTM Threaded heavy pressure pipes Finolex or
approved equivalent( Sch 40 )
131 20mm O.D RMT 40
132 25mm O.D RMT 55
133 32 mm O.D RMT 75
134 40 mm O.D RMT 95
Providing & fixing following size brass full way gate valve ISI
marked & of Leader/GG make or approved equivalent as
directed by Enginner In Charge
135 25mm dia NOS 700
136 20mm dia NOS 550
137 15m dia NOS 400
138 WATER TANK NOS 6500
Supplying and installation of HDPE water tanks Sintex /
Fusion / Polycon make of 1000 litre capacity including 300
mm high brick masonry pedestal of 230mm thick in CM 1:5,
providing 75mm thick RCC 1:2:4 slab with reinforcement
8mm tor @150mm c/c, lifting the tank , making all
necessary GI connections to inlet, outlet, and overflow
nozzles and cleaning the tank before commissioning.
139 SAME as in 46.0 above but with 500L capacity NOS 4000
PVC SOIL / WASTE /RAIN WATER PIPES
Supplying and laying the following size PVC pipe of
4KG/sqcm pressure rating including plain or door type
bends, shoes, offsets, clamps junctions, tees, etc, complete .
140 110 mm dia RMT 200
141 75mm dia RMT 150
NAHANI (FLOOR) TRAP WITH JALI NOS 150
Providing and fixing PVC floor trap of self cleansing design
conforming to IS specs with 100mm inlet, 75mm outlet and
150mm CP hinged grating of 6mm thick with rim. Rate shall
include making all necessary leak proof connections etc .
STONE WARE PIPES RMT 250
Providing and laying 150mm dia. salt glazed stoneware pipes
conforming to IS 651 Grade-A including bends, tees etc,
excavation of trenches, 100 mm thick PCC 1:4:8 bedding,
providing PCC 1:2:4 haunches @ 0.5mc/c , filing the joints
with tarred gasket, plastering with 1:3 cement mortar smoke
testing of joints,backfilling the trenches with excavated earth,
watering, ramming etc., complete.
144 GULLY TRAP WITH CHAMBER NOS 1000
Providing and fixing square mouth gully trap including
constructing 300 X 300 MM internal size brick masonary
chamber with 230mm thick brick masonary in 1:5 cement
mortar, excavation, 75mm thick PCC 1:4:8 bed, plastering
with neat cement finish, Medium duty CI cover with frame
etc. complete.

Providing and constructing following size INSPECTION
CHAMBER with 230mm thick brick masonary in 1:5 cement
mortar, excavation, 75mm thick PCC 1:4:8 bed, plastering
with neat cement finish, heavy duty duty CI cover with frame
etc. complete.
145 600 x 600 mm (Internal dimensions) with 750 mm depth NOS 2600
146 450 x 450 mm (Internal dimensions) with 600 mm depth NOS 2100
147 SEPTIC TANK NOS 16000
Prpoviding & constructing septic tank of size
1200x2000x1800mm depth with excavation ,PCC1:4:8
100mm thick bed , 345/230mm thick brick masonary wall
in CM 1:5 ,RCC1:2:4 100mm thick slab with 8mm tor steel
@150c/c both way , 115mm thick baffle wall with RCC beam
at bottom ,12mm thick smooth cement plaster with water
proofing compound inside and exposed outside portion,
providing 600mmx600mm size medium duty CI cover,
providing 75mm dia PVC vent pipe etc. Complete.
148 SOAK PIT NOS 9000
Providing and constructing soak pit of 2.5m dia (internal)
and 2m depth as per drawing.
PART C ELECTRIFICATION
149 POINT WIRING FOR LIGHT/FAN WITH MODULAR PLATE
SWITCHES ANCHOR ROMA/MK
NOS 450
Providing and laying point wiring in concealed conduits for
the following points using specified 1100V grade PVC
insulated,FRLS multistranded 3 x 1.5 sqmm copper
conductor wires. Rate to include supplying, laying and
securing in position in roof slabs and brick walls or concrete
columns 25 mm dia rigid PVC conduits of approved make
with necessary accessories and junction boxes/pull boxes.
Providing and fixing in the brick walls flush type metal
switch boxes of approved make shade and sufficient size to
accommodate all 6A Modular switches / 3 pin socket,
screws, holders. ceiling roses and the fan regulator wherever
required. Rate to include wall chasing and rough plastering.
Providing and fixing single pole 5A modular plate switches of
MK or ANCHOR ROMA make of approved colour . One switch
shall be provided for each light and fan point.
Rate to include providing main circuit wiring from DB to
switch boards with 2.5 sqmm copper wire also
150 Same as above but for 5A socket controlled by one 5A switch
on the same lighting board
NOS 300
151 Same as above but for 5A socket controlled by one 5A switch
independently mounted including providing wiring with 3
runs of 1.5 sqmm pvc insulated copper wire through PVC
conduit
NOS 500
152 Same as above but for 5/15A socket controlled by 15A
switch independently mounted including providing wiring
with 2 runs of 2.5 sqmm and 1 run of 1.5 sqmm PVC
insulated copper wire through PVC conduit
NOS 550
142
143
153 Same as above but for for AC point with 2 runs of 4
sqmm (P&N)and 1 run of 2.5 sqmm (earthing) PVC insulated
, FRLS multistrand copper cable in 25 mm dia PVC conduict
from MCBDB to 20 A powersocket. The conduit shall be
partly/fully concealed in all types of wall, ceiling etc complete
with all accessories, wiring, termination, connected civil
works, rough plastering etc including supply and fixing of
20A industrial socket controlled by 20A SPMCB of
MDS/HAVELS make.
NOS 1500
Supply, laying , and commissioning of wiring using
following sizes of PVC insulated , FRLS, unsheathed,
multistraned copper wire drawn in PVC conduits. Rate to
include supply of 16 GI fish wire, conduicts & accessories,
wiring, terminations etc complete
154 4 runs of 10 sqmm and 1 run of 6 sqmm copper wire in 40
mm dia PVC conduit from panel to Distribution boards.
RMT 230
155 4 runs of 6 sqmm and 1 run of 4 sqmm copper wire in 32
mm dia PVC conduict from panel to Distribution boards.
RMT 180
156 CEILING FANS NOS 1500
Supplying and fixing of the ceiling fans of
Crompton/GE/Polar/Bajaj with detail as below :
Sweep :1200 mm
Colour :white
Bearing type :Double ball bearing
Down rod :clear 300 mm long
Regulator : Electronic type ANCHOR ROMA/MK
Accessories :Screws, wall nuts etc.
157 EXHAUST FANS NOS 1600
Supply, fixing and commissioning of 305 mm dia Exhaust
fans including bird louvers, frame works and other civil
works like chipping and making the surface good etc
158 SAME AS ABOVE BUT 230MM DIA NOS 1400
LIGHT FIXTURES
Supply, fixing and commissioning of following light fittings.
Rate to include all accessories, interconnection of wires from
ceiling rose to the fittings and fluorescent tube /GLS/PL
lamps , copper choke etc.
159 1 x 36 W tube light fitting with lamp Philips make cat no.
TCS 19/136 HPF or equivalent .
NOS 800
160 1 x 60W spot light luminaire with 1 meter track including
lamp Philips make cat no. DGN 451 or equivalent for
display shelving
NOS 1200
161 1 x 60 W Bulk head luminaire including lamp Phillps cat
no. NXC 101 or equivalent ( Outside building).
NOS 400
162 Angle holder Anchor make including lamp 60W (Toilets). NOS 55
163 1 x 36 W tube light fitting including lamp Phillps cat no
TMS 21/136 HPF or equivalent ( stores, service area)
NOS 450
164 2 x 36 W tube light fitting including lamp Phillps cat no
TBS 50/236 HPF or equivalent . (for false ceiling area)
NOS 2200
165 2 x 36 W tube light fitting including lamp Phillps cat no
TBCS306/236 HPF or equivalent
NOS 2400
Philips energy essential lamps supply and fixing of the
following wattage
166 11W NOS 175
167 14 W NOS 200
168 18 W NOS 220
169 TELEPHONE SOCKET POINT RMT 30
Supply and laying 2 pairs of 0.5 mm dia screened and
shielded telephone wire in 20 mm dia PVC conduit
partly/fully concealed in types of walls , floor etc complete
with all accessories , wiring terminations, connected civil
works, rough plastering etc including supply of 16 GI fish
wire conduit & accessories etc.
170 Supply, fixing and commissioning of 5 pairs of telephone tag
block of Krone type enclosed in suitable MS box. Rate shall
include all accessories, connected civil works for fixing the
same as per specifications.
NOS 1000
171 Supply and installation of modular type telephone socket MK
make in a suitable size box concealed to wall including all
civil works
NOS 300
PART D EXTERNAL ELECTRIFICATION
172 Supply and fixing of wall mounting type meter board made
out of 16 SWG CRCA sheet steel and single iron with 3 nos
200A Fuse cutouts N.L, 1 no earth link , 1 no neutral link
and space for accommodating 1 no. 3 ph, 4 wire KWH meter
complete with adequate size of copper wire interconnections,
powder coating etc. complete.
NO 5000
Supply and erection, testing commissioning of floor
mounting type cubical panel board made out of 16 SWG
CRCA sheet steel with 300 A TPN copper bus bars,
interconnections, earthing, powder coating and comprising
of the followings as required.
173 Incomer : 2 nos 125A TP switch fuse unit with HRC fuses for
DG and EB with interlocking
NOS 70000
1 no 125A TP bus coupler
2 no volt meter with volt meter selector switch, 2 no ammeter
with C T & ammeter selector switch, 2 sets of Phase
indicating lamp (RYB)
Outgoings : 3 nos 63A and 6 nos 32A TP fuse switch unit
with HRC fuse
5KVAR capacitor : 2 nos
174 Supply and erection, testing commissioning of floor
mounting type cubical panel board made out of 16 SWG
CRCA sheet steel with 200 A TPN copper bus bars,
interconnections, earthing, powder coating and comprising
of the followings as required.
NOS 50000
Incomer : 2 nos 125A TP switch fuse unit with HRC fuses for
DG and EB
1 no 125A 4 pole change over switch ( on line)
2 no volt meter with volt meter selector switch, 2 no ammeter
with C T & ammeter selector switch, 2 sets of Phase
indicating lamp (RYB)
Outgoings : 2 nos 63A and 4 nos 32A TP fuse switch unit
with HRC fuse
5 KVAR capacitor : 1 no
Same as above but with following details NOS 45000
Incomer : 2 nos 63A TP switch fuse unit with HRC fuses for
DG and EB
1 no 63A 4 pole change over switch (on line)
2 no volt meter with volt meter selector switch, 2 no ammeter
with C T & ammeter selector switch, 2 sets of Phase
indicating lamp (RYB)
Outgoings : 1 no 63A and 3 nos 32A TP fuse switch unit
with HRC fuse
5 KVAR capacitor : 1 no
176 Supply, installation and commissioning of 63A TPN MCB DB NOS 6000
Incomer : 1 no 63 A , 4 Pole MCB
Outgoings : 18 nos, 10A/16A/20A SP MCBs
177 Supply, installation and commissioning of 32A TPN MCB DB NOS 4000
Incomer : 1 no 32 A , 4 Pole MCB
Outgoings : 12 nos, 10A/16A/20A SP MCBs
Supply and laying following size PVC insulated, sheathed,
armoured cable of approved make
178 3.5CX70 sqmm AL cable RMT 280
179 3.5CX50 sqmm AL cable RMT 230
180 3.5CX35 sqmm AL cable RMT 180
181 3.5CX25 sqmm AL cable RMT 150
182 4CX16 sqmm AL cable RMT 120
183 4CX 6 sqmm AL cable RMT 74
184 4CX2.5 sqmm copper cable RMT 125
185 3CX2.5 sqmm copper cable RMT 100
186 3C x 1.5 sqmm copper cable RMT 85
End termination of following cable with double compression
NFLP gland and crimping sockets
187 3.5CX70 sqmm AL cable NOS 150
188 3.5CX50 sqmm AL cable NOS 120
189 3.5CX35 sqmm AL cable NOS 110
190 4CX25 sqmm AL cable NOS 85
191 4CX16 sqmm AL cable NOS 80
192 4CX6 sqmm AL cable NOS 45
193 4CX2.5 sqmm copper cable NOS 40
194 3CX2.5 sqmm copper cable NOS 40
195 3C x 1.5 sqmm copper cable NOS 40
End termination of following cable with double compression
FLP gland and crimping sockets
196 4C x2.5 sqmm copper cable NOS 55
197 3C x 2.5 sqmm copper cable NOS 50
198 3CX1.5 sqmm copper cable NOS 50
YARD LIGHTING / CABLE TRENCH
175
199 Excavation in any type of soil including WBM /asphalt up to
600mm depth and 300mm wide including supply and laying
150mm thick sand on top and bottom of cable, supply and
laying bricks laid flat on top, back filling trench etc.
Complete.
RMT 120
200 Junction box for yard light pole
Supplying and fixing of weather proof out door junction
box( Baliga or approved equvalent) of IP 64 category of
protection with rubber gasket and having locking
arrangement including required connector, 10A SPMCB.
201 Supply installation of Loop in / loop out box with suitable
erminals to receive the incomming Al/ CU cable and six
sets of outgoing Al/ CU wires of required size. The loop in
Loop out box shall be suitable for fixing in angle iron frame
work.
NOS 425
Yard light pole
202 Supply, fabrication, erection of stepped MS medium yard
light pole with single arm of 6.5m height from pedestal as
per the enclosed drawing clause 2.1 and 5.1 of IS 2723
part III and 2713 including foundation bolt/with detachable
arm as per enclosed drawing, 450mmx450mmx10mm thick
base plate ,painting the pole with two coats of synthetic
enamel paint over a coat of red oxide primer, finishing the
above ground portion of pole with 12mm thick plaster etc.
Complete . Foundation shall be sepately paid
NOS 5400
203 Same as above but with double arm NOS 6000
Street light fitting
204 Supply and fixing of street light fixture of WIPRO make cat
no. WST 65250 1x250W/Philips SRP 601/250 / Bajaj
BGEST 250 SV DD including 250 W compatible Metal
hallide lamp of Philips or equivalent, single piece die cast
aluminium housing complete with all accessories ,choke ,
cover etc. Complete. Rate to include providing 7/20flexible
wire from junction box to top of the pole
NOS 5100
205 Earth pit with plate electrode as per IS 3043 including
excavation of depth 3.2 M, supplying and fixing with GI
plate electrode 600mm x 600mm x 6 mm thick / or copper
plate of same size but 3.16 thick and GI pipe of heavy duty
(4.5mm wall thickness) fixing and using GI nut bolts with
bitumen cloating and welding as per drawing, filling the pit
with alternate layers of charcoal and salt, .backfilling,
constructing brick masonry chamber of 1000(L) x 500 (W)
and 600m depth internal size with 230 thick BM(1:5)
plastering 10mm thick and embedded 50mm dia PVC
conduit opening at two placs with Jute soaked in bitumen at
entrance with funnel for watering, wire mesh, GI flat collars
(2 Nos 50mm x 6mm) with CI frame and cover medium duty
of size 450 mmx 450mm. Rate to inlude carrying out megger
resistance testing of earth pit provided , submitting the
report andpainting resistance, test date and pit identification
on cover top.
NOS 5800
206 Supply and fixing 10 SWG copper wire for earthing
connection to pumps, canopy columns etc.
RMT 30
207 Supply and fixing 25x3 copper flat for earth connection of
panel
RMT 180
208 Providing and fixing 6mm thick MS chequered plate
including making holding arrangements, painting with two
coats of red oxide primer and two coats of synthetic enamel
paint etc.
KG 45
209 Providing and fixing MS angle/channel supports and edge
protection for trench etc. including providing hold fast
,painting with two coats red oxide primer and two coats of
synthetic enamel etc.
KG 44
210 Supply and fixing 20mm thick ISI marked rubber mat SQM 250
PART E DRIVEWAY
MURRUM FILLING:
211 Supply and filling murum in 200 mm thick layers including
levelling with doser, watering,Compacting each layer with
8/10 MT road roller to obtain field dry density 95% of
MDD,Dressing top layer to the required slope,Testing of
murum sample for OMC&MDD and testing of field dry
density by core cutter for checking compaction.Payment will
be made only for compacted thickness.
CUM 300
212 EARTH FILLING: Supply and filling of imported earth of
approved quality in layers not exceeding 200mm including
watering, ramming, compacting, rolling and rerolling with 8-
10 power roller/ mechanical compactors to achieve
maximum compactness all complete as per direction f EIC
CUM 110
213 SAND FILLING CUM 325
NOS 850
Supply and filling with clean locally available approved
quality sand in layers of 150 mm each including compacting
by hand ramming and watering. Mesaurement shall be
on comacted volume and no Provision for bulking etc shall be
allowed.

WATER BOUND MACADUM
Providing and laying WBM in layers of 100/75 mm
compacted thickness each using well graded stone
aggregates of approved quality. Rate includes spreading
metals, hand packing, filling the interstices with spalls,
chips, Screenings and approved quality binder and rolling
each layer with 10 MT power roller with simultaneous
watering till the metal is bound by the water binder paste to
achieve maximum compaction, finishing the surface to
proper grade and level. Rate also to include carrying out the
following tests on aggregates and test results to be submitted
to EIC before use and shall meet the following strength
requirements.
LA Abrasion value : 40 %
Flakiness Index : 15 %
214 First Layer 100 mm thick with 90mm-45mm stone
aggregates . Rate in compacted volume.
CUM 1100
215 First Layer 100 mm thick with 90mm -45 mm over burnt
Jhama brick aggregartes.
CUM 1000
216 Second Layer 75 mm thick with 63 mm - 45 mm stone
aggregares. Rate in Compacted volume.
CUM 1050
217 Third layer of 75mm thick using 53 to 22.2 mm size stone
aggregates. Rate in compacted volume.
CUM 1100
218 Brick Edging : Providing and laying of full brick width and
three quater brick depth including excavation, refilling and
disposal of earth to an unobjectionable place.
RMT 54
219 RCC/CC DRIVEWAY CUM 3960
Providing and laying RCC( 150 mm- 200mm thick) driveway
with 1:1.5:3 nominal mix using 20mm and down size
crushed stone aggregates in panels using slotted MS
channel shuttering, machine mixing, vibrating with screed
board vibrator, pond curing for 14 days,. Concreting shall be
carried out as per IS 456.
Rate shall also include providing approved quality polythene
paper below the driveway, adding superplasticers of
SiKA/Fosroc( conplast P211) or equivalent approved as per
manufacturers specification. constructing horizontal and
longitudinal vatas with 1:10 CM for curing, levelling
depressions if any in the base with 20mm stone aggregates
and stone dust.
Proper slope to be provided in driveway for easy draining of
rain water. Job shall include cutting grooves 4mm wide and
20mm deep by machine and filling the groove with
polysulphide compound/ sika, providing 12mm thick
Shalitek board in the joints between pre cast cover of pipeline
trench or top slab of U/G tank and RCC driveway.
The cement consumption for 1:1.5:3 mix shall be 320
kg/cum and compressive strength shall be 140 kg/sqcm
and 210 kg/sqcm after 7 days and 28 days respectively.
Rate shall be excluding reinforcement steel which shall be
paid separately.
220 Cement Concrete Driveway : CUM 3960
Providing and laying cement concrete in driveway in
required slope and panels including consolidation, finishing
and tampering complete as specified by EIC, mechanically
viibrated using needle and screed board surface vibrators ,
including steel formwork with sturdy M.S channel sections
including curing, providing and filling construction s joints
and dummy joints with shailjet primer or equivalent
including rounding of the edges and filling the grooves
10/20 x 25mm deep at the top for construction joints and
10/20mm x 50mm deep at top for dummy joints with
sealing compound , including making necessary
arrangements for expansion joints, dowels bars etc all
complete. Reinforcement steel including dowelbrs shall be
paid sepately . Rate shall include minium 20 micron
Polythene paper below the driveway, adding superplasticers
of SiKA/Fosroc( conplast or equivalent approved as per
manufacturers specification. constructing horizontal and
longitudinal vatas with 1:10 CM for curing, levelling
depressions if any in the base with 20mm stone aggregates
and stone dust.
221 Same as above but in Concrete Mix 1:2:4 CUM 3480
222 Providing and laying RCC precast slabs of required size with
1:.1.5:3 nominal mix using 20mm and down size crushed
stone aggregates including shuttering, mixing, compacting ,
pond curing for 14 days etc. as per IS 456, transporting
from the place of casting . Reinforcent steel shall be paid
separately.
CUM 3960
223 PCC : 1: 4: 8 Providing and laying PCC 1:4:8 using
40mm/63-40 mm and down size graded stone aggregates
including machine mixing, providing formwork if required,
placing, compacting by hand ramming , curing etc complete.
CUM 2280
224 STEEL REINFORCEMENT MT 45000
Supply, fabrication and placing in position High yield
strength deformed bars/ TMT bars conforming to IS 1786 -
Latest edition grade FE 415 ( SAIL/TISCON/RINL or
approved equivalent) as required and directed at site for
driveway including cutting, bending, placing in position and
tying with 20 SWG binding wire, complete. Quantity shall be
measured as per reinforcement drawing and with theoretical
weights including all authorized laps. Unauthorized chairs,
spacers and laps will not be measured and paid for.
225 ASPHALTING SQM 190
Providing & laying 50 mm compacted thickness
premix asphalt carpet and 12 mm thick seal coat (total
compacted thickness 62mm) on top of WBM surface as per
procedure given below.
1)Applying a tack coat of hot 80/100 asphalt to it @ 10 kg
for 10 sqm after thorough cleaning of WBM surface .
2) Spreading a layer of premix at the rate specified below in
(a) and roll to full compaction with 10 MT roller to the
required slope and compacted thickness of this layer shall
be 50mm.
3)Spreading a layer of seal coat and rolling with 10 MT roller
to the required slope and the total compacted thickness shall
be 62mm. Asphalt required for seal coat is 10 kg for 10 sqm.
Materials to be used for 50mm thick premix carpet.
12.5 nominal size two part and 10mm Nominal size (one
part):approximately 0.70 cum of coarse aggregates
Asphalt 80/100 : 4% by weight of total mix
226 Bituminous macadam 60/70 grade: SQM 210
Bituminous Macadam : 75 mm Thick using 60/70 grade
Bitumem: Providing and laying premix bituminous macadam
base coarse with good quality stone aggregate mix as follows:
1)Applying a tack coat of hot 60/70 asphalt to it @10 Kg
per 10 sqm. after thorough cleaning of WBM surface .
Spreading a layer of premix at the rate specified below in (a)
and roll to full compaction with 10 MT roller to the required
slope and compacted thickness of this layer shall be 75mm.
a)Materials to be used for 75 mm thick Bitumininous
macadam with the following ( : Hard broken granite 20mm=
30% , 12 mm = 35 % 6mm =15%, coarse sand = 15 %, 4 %
Kg by weight of the mix Bitumen 60/70 grade
227 Seal Coat : Providing and laying/Spreading a layer of seal
coat with hard broken aggregate of 6.7 mm size100%
paasing through 11.2mm sive and retined on 2.36 mm sieve(
quantity to be used per 10 SQM is 0.09 CUM) and rolling
with 10 MT roller to the required slope and the total
compacted thickness shall be 12mm. Asphalt (80/100)of
required for seal coat is 19.6 kg for 10 sqm.
SQM 55
228 Mastic Wearing coarse: (25mm thick)Providing 25 mm thick
mastic wearing coarse using stone aggregates as per
following specs. Coarse aggregates to be used 35 % of the
total mix , balance shallbe mixture of coase sand filler
material, limestone powder and mixe with bitumen of grade
80/25 conforming to IS 702 preapared by using mastic
cooker and laid in required level and slopre including
providing anti skid bitumen precoated fine grain hard stone
chipping of approved size at the rate of 0.005 cum per 10
SQM and at an approximate spacing of 10cm centre to
centre in both directions, pressed into surface protuding
1mm to 4mm over mastic surface, including cleaning the
surface , removal of debris etc. All complete.
SQM 360
PAVER BLOCK
SQM 650
230 Same as above but with 80mm thick and M40 grade SQM 560
231 Same as above but with Rubberrised moulded reflective
80mm M-35 grade of Deep chocklate brown colour
Uniregular
SQM 780
HUME PIPE
229 Providing and laying approved brand/make 100mm thick
cement coloured paving blocks of M 45 grade over a bed of
40-50mm thick well compacted river sand bed laid over well
prepared sub base to the required line and level including all
materials, labour, machinery, transportation etc., paving
blocks should have chamfered top edges of not less than
4mm and shall be laid and interlocked with a minimum of
2mm gap which in turn packed with river sand, compacting
with plate vibrator etc. Complete. Edge restraint with RCC
1:1.5:3 will be paid separately.
Supplying, laying, joining and aligning following size
NP3/NP2 class RCC Hume pipes conforming to IS-458 Latest
Edition below approach road whereever directed. Rate to
include joining with cement mortar, excavation up to
required depth and providing and laying PCC 1:2:4
haunching @ 1m c/c . Test certificates from manufacture
shall be submitted and approved by EIC before use.
232 1000mm NB [NP3] RMT 4500
233 300mm NB [NP2] RMT 750
234 225mm NB [NP2] RMT 600
235 150mm NB [NP2] RMT 450
INSPECTION CHAMBER
Providing and constructing following size inspection
chambers with 230mm thick brick masonary in 1:5 cement
mortar, excavation, 75mm thick PCC 1:4:8 bed, plastering
with neat cement finish, providing 16 mm thick MS plate
cover with 35x35x6 angle stiffener and 50x50x6 angle
frame etc. complete.
236 600mmX600mm internal sizeX 700mm depth NOS 3800
237 450mmX450mm internal sizeX 700mm depth NOS 3100
PART F TANK INSTALLATION & PIPELINE
238 Upto 100 KM per tank 45L NOS 5000
239 Upto 100 KM per tank 22KL/16KL/9KL NOS 3000
Beyond 100 KM each additional KM shall be payable extra
as Per 1.2A, B,C for respective tanks.only one way shall be
paid
240 45 KL KM 30
241 22KL KM 23
242 16 KL KM 20
243 9 KL KM 18
244 Excavation for foundation upto 1.5m depth below existing
ground level in any type of soil except hard rock. Rate to
include dressing the sides and bottom, bailing out of water if
encountered, shoring, strutting, backfilling after the
construction of foundation, compacting by the side of the
foundation and disposal of surplus excavated earth
within/outside HPCL's premises to an unobjectionable place,
as directed by the Engineer in Charge including spreading,
watering and compaction, complete
CUM 80
245 Same as in 2 above but upto 3.5 M below EGL CUM 100
246 Providing and laying PCC 1:3:6 with 40mm and dowm Size
stone aggregates in foundation trenches, including
compacting, curing etc. complete.
CUM 2400
Providing and laying RCC 1:2:4,providing steel or plywood
shuttering with proper supports,removal of form work as per
IS code ,preparing mix using mechanical mixer, compacting
using mechanical vibrator, curing with potable water for 14
days etc. complete. Work shall be carried out as per IS 456
latest edition. Rate shall be excluding reinforcement steel
which will be paid separately vide item no 5.
247 Bottom raft CUM 3480
248 Top slab ( Rate shall be including providing Polythene paper
below the slab, providing 12mm thick Shalitek board in
joints to separate pieces. Top slab to be cast in 4/3 pieces )
CUM 3960
249 REINFORCEMENT STEEL WORKS: MT 45000
Supply, straightening, cutting, placing in position as per
drawing, binding at every intersection with two strands of
annealed 20 gauge binding wire , HYSD/TMT bars Grade Fe-
415 conforming to IS 1786.Of SAIL/SRMB/RINL/TISCON
make or equivalent approved.
TANK INSTALLATION
Installaion of HPCL supplied Tanks of following capacity in
earth pit /under driveway including providing holding
down arrangement, Hydrostatic testing to pressure of 3.5m
water column, supplying & filling with water with necessary
50 mm dia pipe & on successful completion emptying out the
water from tank , cleaning & drying the inner surfaces with
cloth/ cotton waste etc., doping with two coats tank mastic
paint of STP make and hot 30/40 bitumen ( total doping
thickness 3mm) ,fixing all fittings as required
250 45KL NOS 15000
Transportation of following capacity horizontal tanks from to
various retail outlet site including loading, unloading etc.
251 22KL NOS 11000
252 16 KL NOS 9500
253 9 KL NOS 7500
254 Brick masonary CUM 2070
Providing 345mm or more thick brick wall with bricks
having compressive strength of minimum 50 kg/sqcm in
cement mortar 1:5 (1 cement: 5 coarse sand) in foundation
and superstructure ,plain or curved including providing
necessary scaffolding , raking the joints on both faces, curing
for 7 days etc. complete.
255 SMOOTH CEMENT PLASTERING SQM 65
Providing and laying smooth cement plaster of 15mm thick
in single coat in 1:3 cement mortar mixed with water
proofing compound to interior walls including providing
necessary scaffolding, curing etc. Complete.
256 SAND FILLING CUM 300
Supply and filling river sand in layers of 200mm thickness
inside masonary pit /earth pit after tank installation
including watering , compaction etc. Complete. Rate shall
be on compacted volume.
257 Manhole cover NO 5700
Supply, fabrication and fixing of manhole cover of size
900x900 mm with 65x65x6 angle frame and 16mm thick
MS plate with 50x50x6 stiffener including painting with two
coats of red oxide primer and two coats of synthetic enamel
paint. Grouting in PCC included in the scope of the vendor
at no extra cost
258 Pump Island RMT 1200
Construction of pump island 1m wide with 230mm thick
brick masonry in CM 1:5, 12mm thick plastering in Cm 1:4
roughened to receive granite tiles including excavation,
75mm thick PCC 1:4:8 , sand filling and constructing the
wall 150mm above the finished driveway level and 600mm
below the finished driveway level .
Installation of Dispensing Pumps
Installation of MONO/DUAL/MPD pumps on pedestal
including providing & fixing MS angle frame 65x65x6 &
connecting suctionpipe, electrical, earthing connections to
the pump etc. Complete. Structural steel shall be paid
sepately.
259 Installation MONO pumps NOS 500
260 Installation of DUAL pumps NOS 600
261 Installation of MPD pumps NOS 2500
Pipe Lines
Supplying & Laying C Class ERW black steel screwed
pipeline Conforming to IS 1239 (part I) latest edition to the
required slope & alignment including doping pipe line with 3
coats of Shalimastic HD THIXOTROPIC of STP cold
applied anti corrosive treatment after preparing the surface
as per manufacturer specifications. The joints are to be
made leak proof by using jointing materials like Litharge,
Glycerin, Shellac, holdite . The pipes laid above ground shall
be painted with two coats of synthetic enamel over two coat
of zinc phosphate primer of approved quality and shall be
color coded as per instruction of EIC. The pipeline shall be
tested at a specified test pressure of 5kg/sqcm or as
directed by EIC.
262 40mm dia RMT 450
263 50mm dia RMT 550
264 80mm dia fill pipe RMT 750
Supply and fixing ISI marked angular check valve of
Leader/GG make
265 40mm dia NOS 1100
266 50mm dia NOS 1250
Fill cap and Vent hood
267 Supply and fixing MS fill cap with locking arrangement
including Godrej 6 lever brass lock
NOS 400
268 Supply and fixing 40mm dia vent hood in vent pipe NOS 300
269 Supply and fixing MS Dip Cap with locking arrangement
including 6 lever brass lock
NOS 350
Granite works:
270 Providing and fixing 18 mm thick pre polished water cut
black granite slab for pump island top including providing
25mm thk bed cement mortar 1:5 (1 cement : 5 coarse sand)
, floating cement slurry and finishing the joints with white
cement mixed with matching colour pigment.
SQM 2450
271 Providing and fixing 10 mm thick water cut black granite pre
polished water cut black granite tiles for pump island dado
including providing 12mm thick bed 1:4 (1 cement : 4 coarse
sand) , floating cement slurry and finishing the joints with
white cement mixed with matching colour pigment
SQM 1400
Pipeline trench:
272 Providing pipeline trench as per drawing with internal size
300mm wide x400mm depth including excavation, 100mm
thick PCC 1:4:8, 230mm thick brick masonary in 1:5 CM,
12mm thick plastering inside in 1:4 CM, filling trench with
sweet river sand, 150mm thick RCC 1:2:4 cover with
reinforcement 10mm tor @ 125mm c/c on top and bottom as
main steel and 8mm tor ring as distribution, 50x50x6 angle
edging, curing etc. complete.
RMT 1300
273 Same as above but with 450mm wide .
RMT 2500
PART G DISMANTLING WORKS
Exhuming under ground tanks with all fittings from earth
pit including disconnecting suction, fill, vert pipe , opening
man hole cover, excavation, dewatering if encountered,
degassing of tank, stacking the tank as directed by EIC etc.
Complete. Back filling with sand will be paid separately.
274 9KL tank NOS 4500
275 16/14 KL tank NOS 5500
276 22 KL tank NOS 6500
277 45 KLtank NOS 7500
278 Dismantling of Dispensing Pumps including de enerziging
the pump, disconnecting the suction pipieline, and closing
with end cap etc without causing any damage to the
pumps. And shiting thepump within 50 M radius as directed
by EIC.
NOS 250
279 Dismantling of Pump Island MT 350
Dismantling of existing building/structures
280 Dismantling of RCC works viz roof, beam, column ,
driveway including seggregation and stacking of
reinforcement bars etc.carting away debris to a place within
5 KM radius. The Debris
CUM 550
281 Dismantling roofing including ridges, valleys and gutters
etcand removal of AC sheet/ GI sheet from roof , false ceiling
etc. removing J bolts , bitumen and Gi washer and stacking
at site , transprtation and unloading of the same to a
distance within 5 KM radius directed by EIC.
SQM 25
282 Dismantling steel work in built up sections in angles, Tees,
flats, Channels including all gusset plates, bolts, nuts,
cutting welding , (including trusseres rafters purlins upto a
height of 10 M above ground level).bolts etc including
dismembering and stacking within 5 KM m radius.
MT 4000
283 Dismantling of brick masonary/ cement concerete/RR
masonary/ including carting away debris to an
unobjectionable place within a radius of 5 Km/M .
CUM 300
PART G BORE WELL
284 Removal of MS/ wooden/Aluminium doors/ windows/fixed
glazing and stacking as directed by EIC.
SQM 45
285 Drilling 5 dia borewell in all kinds of soil including rock
using air compressor rig. Rate to include washing with
compressor after installation of casing pipe.
RMT 200
286 Supply and fixing 5 dia casing pipe HDPE 6 kg/ sqcm
pressure rating all complete.
RMT 235
287 supply and fixing 5 dia HDPE slotted 6Kg/ Sqcm pressure
rating all complete.
RMT 280
288 Supply and fixing and commissioning of single phase
submersible pump of Kirloskar cat no. KU4-0709S
discharge range 1.2-8 cum/hr head range 59-10m along
with dry run preventor and starter
NOS 17500
289 Supply and installation of 32mm NB HDPE pipe with GI
short piece at both end
RMT 75
290 Supply and fixing of C class GI pipe with as above in item
no.6( in case HDPE pipe is not to be used.
RMT 180
291 Supply and fixing of 32 mm NB HDPE pipe and 25mm HDPE
pipe with required accessories for jet pump.
RMT 120
292 Supply and laying 3CX2.5 sqmm copper cable
RMT 80
293 Carrying out Geological Testing for finalisation of location of
borewell
NO 2000
294 Supply and installation of 1 HP single phase jet pump with
starter with end termination earthing etc complete.
NOS 6000
PART H COMPRESSOR
295 Installation of HPCL supplied compressor including PCC
1:2:4 foundation,foundation bolt etc. complete.
NOS 2500
296 Fixing tyre inflator gauge wall mounted model ELGI make
with 5m hose including providing 50x50x6 angle post
NOS 300
297 Supply and laying15mm dia GI pipe medium duty RMT 100
298 Supply and fixing MS ball valve 15mm dia NOS 450
PART I LAND SCAPING
299 Green scaping with sprikler/ drip system using green grass,
seeds/ manuring/ watering/ growing the grass/ treaming/
dressing the top grass lawn etc. Complete. Job includes
supply of good quality fertile soil spreading/ screening the
soil for watering the green lawn.
SQM 110
Supplying and laying of the GI medium duty pipeline of
following different sizes including GI bends / elbows/ Tee
joint/ socket/ union/ brush / plug etc. Complete for water
fountain with approved make.
300 50mm NB RMT 290
301 40mm NB RMT 220
302 25mm NB RMT 150
303 25mm NB RMT 120
304 15mm NB RMT 100
Supplyng and fixing of following sizes Gunmetal gate valve of
approved make
305 50mm NB NOS 800
306 40mm NB NOS 700
307 25mm NB NOS 500
308 15 mm NB NOS 300
309 Fountain
NOS 16000
Supply and fixing of fountain Nozzle assembly of brass of
approved make of 10 high water thrown in different pattern
along with supply and installation and commissioning of 1
HP monoblock submersible pump including laying of cable ,
supplying of indoor type panel consisiting switch , timer ,
fuse, cable necessary intergral wiring for both the under
water ligting with colour film filter, lamps etc. and pump
including supply and fixing of contol valve etc.complete. The
control panel shall be 30M from the pool.The pipeline upto
the pump suction and cable shall be payable under a
separate item
310 Supply and fixing of under water luminaires as per Philiphs
catlogue No NHG-10 with 100 watt lamp termination etc
complete.
NOS 3300

You might also like