Harman-Kardon AVR2650 Service Manual PDF

harman/kardon
AVR 2650
7 X 95W 7.1 CHANNEL A/V RECEIVER
SERVICE MANUAL
CONTENTS
ESD WARNING.......2
LEAKAGE TESTING.......3
BASIC SPECIFICATIONS..4
PACKAGING.5
FRONT PANEL CONTROLS......6
REAR PANEL CONNECTIONS.8
REMOTE CONTROL FUNCTIONS.10
CONNECTIONS/INSTALLATION....12
OPERATION....19
TROUBLESHOOTING GUIDE.........24
REMOTE & PROCESSOR RESETS.......25
DISASSEMBLY........26
UNIT EXPLODED VIEW.....27
EXPLODED VIEW PARTS LIST28
AMP BIAS ADJUSTMENT..29
BLOCK DIAGRAM...30
PCB DRAWINGS.32
ELECTRICAL PARTS LIST.47
SEMICONDUCTOR PINOUTS....103
SCHEMATICS.224
WIRING DIAGRAM.241
harman/kardon, Inc.
Released 2011
Discontinued XXXX
8500 Balboa Blvd..

Northridge, CA. 91329
Rev0 6/2011
AVR 2650
harman/kardon
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and
semiconductor "chip" components.
The following techniques should be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on
your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to
prevent electrostatic charge build-up or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges
sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement
ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the
chassis or circuit assembly into which the device will be installed.
CAUTION : Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together
or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
Each precaution in this manual should be followed during servicing.

Components identified with the IEC symbol
in the parts list are special significance to safety. When replacing a component identified with
, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the
parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably
insulated from the supply circuit before retuming the product to the customer.
AVR 2650
harman/kardon
SAFETY PRECAUTIONS
The following check should be performed for the continued
protection of the customer and service technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground (water
pipe, conduit, etc.) by connecting a leakage current tester
between the earth ground and all exposed metal parts of the
appliance (input/output terminals, screwheads, metal
overlays, control shaft, etc.). Plug the AC line cord of the
appliance directly into a 120V AC 60Hz outlet and turn the
AC power switch on. Any current measured must not exceed
o.5mA.
Leakage
current
tester
Device
under
test
Test all
exposed metal
surfaces
Also test with
plug reversed
(Using AC adapter
plug as required)
Reading should
not be above
0.5mA
Earth
ground
AC Leakage Test
ANY MEASUREMENTS NOT WITHIN THE LIMITS

OUTLINED ABOVE ARE INDICATIVE OF A
POTENTIAL SHOCK HAZARD AND MUST BE
CORRECTED BEFORE RETURNING THE APPLIANCE
TO THE CUSTOMER.
AVR 2650
harman/kardon
AVR
Specifications
Specifications
Video Section
Audio Section
Stereo power:
Multichannel power:
Television format:
Input sensitivity/impedance:
Surround system adjacent

channel separation:
Dolby Pro Logic/DPLII: 40dB

Dolby Digital: 55dB
DTS: 55dB
Frequency response (@ 1W):
10Hz 130kHz (+0dB/3dB)
High instantaneous current

capability (HCC):
Unmeasurable
Slew rate:
40V/sec
Version 1.4a with 12-bit Deep Color
35 amps
Transient intermodulation
distortion (TIM):
10Hz 8MHz (3dB)
HDMI:
100dB
1Vp-p/75 ohms
Video frequency response

(composite video):
200mV/47k ohms
Signal-to-noise ratio (IHF-A):
1Vp-p/75 ohms
Output level/impedance:
AVR 3650/AVR 365: 110W per channel, two channels

driven @ 8 ohms, 20Hz 20kHz, <0.09% THD
NTSC (AVR 3650/AVR 2650);

PAL (AVR 365/AVR 265)
Input level/impedance:

General Specifications
Power requirement:
120V AC/60Hz (AVR 3650/AVR 2650);

220V 240V AC/50Hz 60Hz (AVR 365/AVR 265)
Power consumption:
<0.5W (standby);
480W maximum (AVR 3650/AVR 365);
420W maximum (AVR 2650/AVR 265)
Dimensions (W x H x D):
17-5/16" x 6-1/2" x 17-1/8"

(440mm x 165mm x 435mm)
Weight
(AVR 3650/AVR 365): 27.25 lb (12.4kg)

(AVR 2650/AVR 265): 24.4 lb (11.1kg)
Depth measurement includes knobs, buttons and terminal connections.

Height measurement includes feet and chassis.
FM Tuner Section
Frequency range:
87.5 108.0MHz
Usable sensitivity IHF:
1.3V/13.2dBf
Signal-to-noise ratio (mono/stereo):
70dB/68dB
Distortion (mono/stereo):
0.2%/0.3%
Stereo separation:
40dB @ 1kHz
Selectivity (400kHz):
70dB
Image rejection:
80dB
IF rejection:
90dB
AM Tuner Section
Frequency range:
520 1710kHz (AVR 3650/AVR 2650)

522 1620kHz (AVR 365/AVR 265)
Signal-to-noise ratio:
45dB
Usable sensitivity (loop):
500V
Distortion (1kHz, 50% mod):
0.8%
Selectivity (10kHz):
30dB
AVR 2650
harman/kardon
AVR 2650
OUTER CARTON
FOAM PAD (L)

FOAM PAD (R)
AVR 2650
OUTER CARTON
AVR 2650
harman/kardon
AVR
Front-Panel Controls
Front-Panel Controls
Power
Power
Button
Button
Power
Power
Indicator
Indicator
Info
Info
Button
Button
IR
IR
Sensor
Sensor
Setup
Setup
Button
Button
USB
USB
Port
Port
Video
Video
Modes
Modes
Button
Button
Resolution
Resolution
Button
Button
HDMI Front
HDMI Front
Input Connector
Input Connector
Audio
Audio
Effects
Effects
Button
Button
Up/Down
Up/Down
Buttons
Buttons
Message
Message
Display
Display
Back/Exit
Back/Exit
Button
Button
Surround
Surround
Modes
Modes
Button
Button
OK
OK
Button
Button
Left/Right
Left/Right
Buttons
Buttons
Volume
Volume
Knob
Knob
Source List
Source List
Button
Button
Headphone Jack/
HeadphoneJack/
EzSet/EQ
EzSet/EQ
Mic Input
Mic Input
Continued on next page
AVR 2650
harman/kardon
AVR
Front-Panel Controls, continued
Front-Panel Controls, continued

Resolution button: Press this button to access the AVRs video output resolution
setting: 480i, 480p, 720p, 1080i, 1080p or 1080p/24Hz. Use the Up/Down and OK
buttons to change the setting.
Power Indicator: This LED has three possible modes:

LED is off: Indicates that the AVR is unplugged or the rear-panel Main Power switch
is off.
LED glows amber: Indicates that the AVR is in the Standby mode.
IMPORTANT NOTE: If you set the AVRs video output resolution higher than
the capabilities of the actual connection between the AVR and your TV or
video display, you will not see a picture. If you are using the composite video
connection from the AVR to your TV (see Connect Your TV or Video Display, on
page 17), press the Resolution button and use the Up/Down and OK buttons to
change the resolution to 480i.
LED glows white: Indicates that the AVR is turned on.

IMPORTANT NOTE: If the PROTECT message ever appears on the AVRs frontpanel message display, turn off the AVR and unplug it from the AC outlet.
Check all speaker wires for a possible short-circuit (the + and conductors
touching each other or both touching the same piece of metal). If a short-circuit
is not found, bring the unit to an authorized Harman Kardon service center for
inspection and repair before using it again.
Audio Effects button: Press this button to access the Audio Effects submenu,
which allows you to adjust the AVRs tone controls and other audio controls. See Set
Up Your Sources, on page 26, for more information.
Video Modes button: Press this button for direct access to the Video Modes
submenu, which contains settings you can use to improve the video picture. Use
the OK button to scroll through the different modes, and use the Up/Down and Left/
Right buttons to make adjustments within each mode. See Set Up Your Sources, on
page 26, for more information.
Power button: Press this button to turn the receiver on or to place it in the Standby
mode.
Setup button: Press this button to access the AVRs main menu.
Info button: Press this button to access the AVRs Source submenu, which contains
the settings for the source currently playing. Use the Up/Down buttons to scroll
through the different settings.
Surround Modes button: Press this button to select a listening mode. The Surround
Modes menu will appear on screen, and the menu line will appear in the front-panel
display. Use the Up/Down buttons to change the surround-mode category and the
Left/Right buttons to change the surround mode for that category. See Set Up Your
Sources, on page 26, for more information.
Message display: Various messages appear in this two-line display in response

to commands and changes in the incoming signal. In normal operation, the current
source name appears on the upper line, while the surround mode is displayed on
the lower line. When the on-screen display menu system (OSD) is in use, the current
menu settings appear.
Back/Exit button: Press this button to return to the previous menu or to exit the
menu system.
IR sensor: This sensor receives infrared (IR) commands from the remote control.
It is important to ensure that the sensor is not blocked. AVR 3650/AVR 365 only:
If covering the IR sensor is unavoidable (such as when the receiver is installed inside
of a cabinet), connect an optional infrared receiver to the Remote IR In connector on
the AVRs rear panel.
Left/Right buttons: Use these buttons to navigate the AVRs menus.

OK button: Press this button to select the currently highlighted item.
Headphone jack/EzSet/EQ Mic input: Connect a 1/4" stereo headphone plug
to this jack for private listening. This jack is also used to connect the supplied
microphone for the EzSet/EQ procedure described in Configure the AVR For Your
Speakers, on page 25.
Up/Down buttons: Use these buttons to navigate the AVRs menus.

Volume knob: Turn this knob to raise or lower the volume.
Source List button: Press this button to select a source device to watch/listen to.
Use the Up/Down buttons to scroll through the source-device list, and press the OK
button to select the source being displayed.
USB port: You can use this port to perform software upgrades that may be offered in
the future. Do not connect a storage device, peripheral product or a PC here, unless
you are instructed to do so as part of an upgrade procedure.
HDMI (High-Definition Multimedia Interface) Front Input connector: Connect
an HDMI-capable source component that will be used only temporarily, such as a
camcorder or game console, here.
AVR 2650
harman/kardon
AVR
Rear-Panel Connectors
Rear-Panel Connectors
HDMI
HDMI
Monitor Out
Monitor Out
Connector
Connector
Composite
Composite
Video Monitor
Video Monitor
Out Connector
Out Connector
Digital Audio
Digital Audio
Input Connectors
Input Connectors
Analog
Analog
Record Out
Record Out
Connector
Connector
Radio Antenna
Radio Antenna
Connectors
Connectors
Composite
Composite
Video Input
Video Input
Connectors
Connectors
Composite
Composite
Video Record
Video Record
Out Connector
Out Connector
12V
12V
Trigger
Trigger
Connector
Connector
Component
Composite
Video Input
Video Input
Connectors
Connectors
Zone IR In
Zone 22 IR In
Connector
Connector
(AVR 3650/AVR365)
3650/AVR 365)
HDMI Input
HDMI Input
Connectors
Connectors
Subwoofer
Subwoofer
Connector
Connector
Zone 2 Out
Zone 2 Out
Connector
Connector
Optical
Optical
Digital Output
Digital Output
Connector
Connector
Speaker
Speaker
Connectors
Connectors
Network
Network
Connector
Connector
Analog Audio
Analog Audio
Input Connectors
Input Connectors
Main Power
Main Power
Switch
Switch
SIRIUS Tuner
SIRIUS Tuner
Connector
Connector
(AVR 3650/AVR 2650)
3650/AVR 2650)
AC Input
AC Input
Connector
Connector
RS-232
RS-232
Connector
Connector
The Bridge IIIP

TheBridge IIIP
Connector
Connector
IR Remote
IR Remote
In/Out Connectors
In/Out Connectors
(AVR 3650/AVR365)
(AVR 3650/AVR 365)
Fan
Fan
Vents
Vents
Rear-Panel Connectors (AVR 3650 shown)
Analog Record Out connector: Connect this analog audio output to the analog
audio input of a recording device. A signal is available at this output whenever an
analog audio source is playing.
HDMI Input connectors: An HDMI connection transmits digital audio and video
signals between devices. If your source devices have HDMI connectors, using them
will provide the best possible video and audio performance quality. Since the HDMI
cable carries both digital video and digital audio signals, you do not have to make
any additional audio connections for devices you connect via the HDMI connection.
See Connect Your Audio and Video Source Devices, on page 18, for more information.
HDMI Monitor Out connector: If your TV has an HDMI connector, use an HDMI
cable (not included) to connect it to the AVRs HDMI Monitor Out connector. The
AVR will automatically transcode component and composite video input signals to
the HDMI format (upscaling to as high as 1080p), so you do not need to make any
other connections to your TV from the AVR or from any of your video source devices.
Composite Video Input connectors: Use composite video connectors for video
source devices that dont have HDMI or component video connectors. You will also
need to make an audio connection from the source device to the AVR. See Connect
Your Audio and Video Source Devices, on page 18, for more information.
Notes on using the HDMI Monitor Out connector:
Digital Audio Input connectors: If your non-HDMI source devices have digital
outputs, connect them to the AVRs digital audio connectors. NOTE: Make only one
type of digital connection (HDMI, optical or coaxial) from each device. See Connect
Your Audio and Video Source Devices, on page 18, for more information.
When connecting a DVI-equipped display to the HDMI Monitor Out connector,

use an HDMI-to-DVI adapter and make a separate audio connection.
Make sure the HDMI-equipped display is HDCP (High-bandwidth Digital Content
Protection)-compliant. If it isnt, do not connect it via an HDMI connection; use an
analog video connection instead and make a separate audio connection.
AVR 2650
harman/kardon
AVR
Rear-Panel Connectors, continued
Rear-Panel Connectors, continued

Speaker connectors: Use two-conductor speaker wire to connect each set of
terminals to the correct speaker. See Connect Your Speakers, on page 17, for more
information.
Composite Video Monitor Out connector: If your TV or video display does not
have an HDMI connector, use a composite video cable (not included) to connect the
AVRs Composite Video Monitor Out connector to your TVs composite video input.
NOTE: The HDMI connection to your TV is preferred. If you use the composite video
connection to your TV, you will not be able to view the AVRs on-screen menus.
NOTE: The speaker connectors, also called Assigned Amp speaker connectorsare used for the surround back channels in a 7.1- channel home theater, or you
can reassign them to a remote room for multizone operation or to front height
channels for Dolby Pro Logic IIz operation. See Place Your Speakers, on page
13, for more information.
Composite Video Record Out connector: Connect an analog video recorders video
input connector to the AVRs Composite Video Rec Out connector. You can record
any composite video input signal. NOTE: To record the audio and video from the
source device, connect the AVRs Analog Record Output connectors to the analog
video recorders audio inputs.
Network connector: Use a Cat. 5 or Cat. 5E cable (not supplied) to connect the AVRs
Network connector to your home network to enjoy Internet radio and content from
DLNA-compatible devices that are connected to the network. See Connect to Your
Home Network, on page 20, for more information.
Component Video Input connectors: If any of your video source devices have
component video connectors (and do not have HDMI connectors), using the
component video connectors will provide superior video performance. You will also
need to make an audio connection from the device to the receiver. See Connect Your
Audio and Video Source Devices, on page 18, for more information.
Main Power switch: This mechanical switch turns the AVRs power supply on or off.
It is usually left on, and it cannot be turned on or off using the remote control.
SIRIUS Tuner connector: Connect a SIRIUSConnect satellite radio tuner module

here. (Not included. Available at www.sirius.com.) See Connect Your Audio and Video
Source Devices, on page 18, for more information.
AC Input connector: After you have made all other connections, plug the supplied
AC power cord into this receptacle and into an unswitched wall outlet.
RS-232 connector: This connector is used to connect to external control hardware.
Consult a certified professional installer for more information.
12V Trigger connector: This connector provides 12V DC whenever the AVR is on.
It can be used to turn on and off other devices such as a powered subwoofer.
IR Remote In/Out connectors (AVR 3650/AVR 365 only): When the IR sensor
on the front panel is blocked (such as when the AVR is installed inside a cabinet),
connect an optional IR receiver to the IR Remote In jack. The IR Remote Out jack
may be connected to the IR input of a compatible product to enable remote control
through the AVR.
Zone 2 IR Input connector (AVR 3650/AVR 365 only): Connect a remote IR receiver
located in Zone 2 of a multizone system to this jack to control the AVR (and any
source devices connected to the Remote IR Output connector) from the remote zone.
The Bridge IIIP connector: Connect an optional Harman Kardon The Bridge IIIP
docking station to this input. Insert the plug until it snaps into place in the connector.
IMPORTANT: Connect The Bridge IIIP only with the AVRs power turned off.
Fan Vents: These vents are used by the AVRs fan to cool the system. Maintain
a clearance of at least three inches (75mm) from the nearest surface to avoid
overheating the unit. It is normal for the fan to remain off at most normal volume
levels. An automatic temperature sensor turns the fan on only when it is needed.
Radio Antenna connectors: Connect the included AM and FM antennas to their

respective terminals for radio reception.
Zone 2 Out connectors: Connect these jacks to an external amplifier to power the
speakers in the remote zone of a multizone system.
IMPORTANT NOTE: Never block the fan vents. Doing so could allow the AVR to
overheat to dangerous levels.
Subwoofer connector: Connect this jack to a powered subwoofer with a line-level

input. See Connect Your Subwoofer, on page 17, for more information.
Analog Audio Input connectors: Use the AVRs Analog Audio Input connectors for
source devices that dont have HDMI or digital audio connectors. See Connect Your
Audio and Video Source Devices, on page 18, for more information.
Optical Digital Output connector: Connect a digital audio recorders optical digital
input to the AVRs Optical Digital Output connector. You can record both coaxial and
optical digital audio signals.
AVR 2650
harman/kardon
AVR
System Remote Control Functions
System Remote Control Functions

IR Transmitter Lens
AVR Power On/Off

AVR Power On/Off
Buttons
Buttons
Device Power On/Off

Buttons
Source Selector
Source Selector
Buttons
Buttons (AVR (AVR 2650/AVR 265)
2650/AVR 265)
Source Selector
Source Selector
Buttons 3650/AVR 365)
Buttons (AVR (AVR 3650/AVR 365)
Audio Effects
Audio Effects
Button
Button
Video Modes
Video Modes
Button
Button
Surround Modes
Button
Number
Buttons
LastLast Channel
Channel
Button
Button
Activity Button
Back/Exit
Back/Exit
Button
Button
Menu Button
Up/Down/Left/Right
Buttons
OK OK Button
Button
Disc Menu
Button
Backlight Button
Backlight Button
(AVR 3650/AVR 365 only)

A/B/C/D Buttons
A/B/C/D Buttons
Volume Up/Down
Volume Up/Down
Buttons
Buttons
Channel Up/Down and

Page Buttons
Mute Button
Mute Button
Transport Control
Buttons
InfoInfo Button
Button
Sleep Button
AVRAVR Button
Button
Learn Button
Zone Selector
Zone Selector
Switch
Switch
10
AVR 2650
harman/kardon
AVR
System Remote Control Functions, continued
System Remote Control Functions, continued

In addition to controlling the AVR, the AVR remote is capable of controlling eight other
devices, including an iPod/iPhone device docked in a The Bridge IIIP docking station
connected to the AVR. During the installation process, you may program the codes for
each of your source components into the remote. (See Program the Remote to Control
Your Source Devices and TV, on page 23, for programming information.) To operate
a component, press its Source Selector button to change the remotes control mode.
A buttons function depends on which component is being controlled. See Table A13
in the Appendix for listings of the functions for each type of component. Most of
the buttons on the remote have dedicated functions, although the precise codes
transmitted vary depending on the specific device being controlled. Due to the wide
variety of functions for various source devices, we have included only a few of the
most-often used functions on the remote: alphanumeric keys, transport controls,
television-channel control, menu access and power on and off. Buttons dedicated to
the AVR AVR Power On/Off, Audio Effects, Video Modes, Surround Modes, Volume,
Mute and Sleep Settings are available at any time, even when the remote is
controlling another device. To return the remote to the AVR control mode at any time,
press the Setup button.
AVR Power On/Off buttons: Press these buttons to turn the AVR on and off. The Main
Power switch on the AVRs rear panel must be on for this button to work.
IR Transmitter Lens: As buttons are pressed on the remote, infrared codes are
emitted through this lens.
Device Power On/Off buttons: Press a devices Source Selector button, then press
these buttons to turn the device on and off.
Source Selector buttons: Press one of these buttons to select a source device, e.g.,
Blu-ray, Cable/Sat, Radio, etc. This action will also turn on the AVR and switch the
remotes control mode to operate the selected source device. NOTE: The first press of
the Radio Source Selector button switches the AVR to the last-used tuner band (AM,
FM or SIRIUS). Each successive press changes the band.
Audio Effects button: Press this button to access the Audio Effects submenu, which
allows adjustment of the AVRs tone and other audio controls. See the Set Up Your
Sources section, on page 26, for more information.
Back/Exit button: Press this button to return to the previous menu or to exit the
menu system.
Menu button: This button is used within the tuner menus (including SIRIUS Radio)
and The Bridge IIIP control menu, and is also used to display the main menu on some
source devices. To display the AVRs menu system, press the Setup button.
Up/Down/Left/Right buttons: These buttons are used to navigate the menu system
and to operate the tuner.
OK button: This button is used to select items from the menu system.
Backlight button (AVR 3650/AVR 365 only): Press this button to illuminate the
buttons on the remote. Press it again to turn the backlight off, or wait 5 seconds after
the last button press for the light to turn off on its own.
Disc Menu button: To display the discs menu while a DVD or Blu-ray Disc is playing,
press the Blu-ray Source Selector button, then press this button.
A/B/C/D buttons: These buttons can be used as additional source buttons and can
also operate certain functions when used with some source devices. See Table A13
in the Appendix for details. These buttons are also used with a Teletext-capable
television if your broadcast, cable or satellite provider offers Teletext service.
Volume Up/Down buttons: Press these buttons to raise or lower the volume.
Channel Up/Down and Page buttons: When the tuner has been selected, press
these buttons to select a preset radio station. While operating a cable, satellite or
HDTV set-top box or a television, press these buttons to change channels.
Mute button: Press this button to mute the AVRs speaker-output connectors and
headphone jack. To restore the sound, press this button or adjust the volume.
Transport Control buttons: These buttons are used to control source devices and
The Bridge IIIP.
Info button: Press to display the AVRs Info Menu, which contains the settings for
the current source.
Setup button: Press to display the AVRs Main Menu or to switch the remote to the
AVR control mode.
Video Modes button: Press this button for direct access to the Video Modes
submenu, which contains picture adjustments you can use after you have adjusted
the picture settings on your TV or video display. See the Advanced Functions section,
on page 33, for more information.
Sleep button: Press this button to activate the sleep timer, which turns off the
receiver after a programmed period of time. Each press increases the time by 10
minutes, up to 90 minutes ending with the Sleep Off message.
Surround Modes button: Press this button to access the Surround Modes submenu.
Select a surround-mode category: Auto Select, Virtual Surround, Stereo, Movie, Music
or Game. When you select the category, it is highlighted and the surround mode
changes.
Learn button (AVR 3650/AVR 365 only): The AVR 3650/AVR 365 remote is capable
of learning individual IR codes from the original remote that came with a source
device. See Program the Remote to Control Your Source Devices and TV, on page 23,
for more information.
To change the surround mode for the selected category, press the OK button when the
menu line is highlighted and use the Up/Down buttons to select one of the available
surround-mode options. Press the OK button; or press the Back/Exit button to exit the
Surround Modes menu and display the next higher menu in the hierarchy. See the
Advanced Functions section, on page 33, for more information.
Zone Selector switch: Use this switch to select whether the AVR commands will
affect the main listening area (Zone 1) or the remote zone of a multizone system
(Zone 2). For normal operation, leave the switch in the Zone 1 position.
Number buttons: Use these buttons to enter numbers for radio-station frequencies
or to select station presets.
Last Channel button: When controlling a cable, satellite or HDTV set-top box or a TV,
press this button to return to the previous television channel.
Activity button: With this button you can program the remote to store up to 11
different Macros (Activities). (A Macro is a series of commands that are transmitted
by a single button press.) Execute a Macro by pressing this button, followed by the
Number button (or the AVR Power On button) into which you programmed the Macro.
See Programming Macro (Activity) Commands, on page 41, for more information.
11
AVR 2650
harman/kardon
AVR
Types of Home Theater System Connections

Subwoofer Connections
There are different types of audio and video connections used to connect the AVR to your
speakers, your TV or video display, and your source devices. The Consumer Electronics
Association has established the CEA color-coding standard.
The subwoofer is a speaker dedicated to reproducing only the low (bass) frequencies,
which require more power. To obtain the best results, most speaker manufacturers offer
powered subwoofers that contain their own ampliers. Use a single RCA audio cable to
make a line-level (non-amplied) connection from the AVRs Subwoofer connector to a
corresponding input jack on the subwoofer.
Analog Audio Connection
Color
Front Left/Right
White/Red
Center
Green
Surround Left/Right
Blue/Gray
Surround Back/Front Height Left/Right
Brown/Tan
Subwoofer
Purple
Digital Audio Connection
Color
Coaxial (input or output)
Orange
Optical Input
Black
Optical Record Output
Gray
Although the AVRs purple subwoofer output looks similar to a full-range analog audio
jack, it is ltered so that only the low frequencies pass through it. Dont connect this
output to any device other than a subwoofer.
Analog Video Connection
Color
Source Device Connections
Component Video
Red/Green/Blue
Composite Video
Yellow
Audio and video signals originate in source devices (components where a playback
signal originates) such as your Blu-ray Disc or DVD player, CD player, DVR (digital
video recorder) or other recorder, tape deck, game console, cable or satellite television
tuner, an iPod or iPhone (docked in an optional The Bridge IIIP docking station) or an
MP3 player. The AVRs FM/AM tuner also counts as a source, even though no external
connections are needed other than the FM and AM antennas and an optional SIRIUS
tuner module. Separate connections are required for the audio and video portions of the
source devices signal, except for digital HDMI connections. The types of connections
you use will depend upon the capabilities of the source device and of your TV or video
display.
Speaker Connections
Speaker cables carry an amplied signal from the AVRs speaker terminals to each
loudspeaker. They contain two wire conductors, or leads, that are differentiated in some
way, such as with colors or stripes.
The differentiation helps you maintain proper polarity, without which your systems lowfrequency performance can suffer. Each speaker is connected to the AVRs speakeroutput terminals using two wires, one positive (+) and one negative (). Always connect
the positive terminal on the speaker, which is usually colored red, to the positive terminal
on the receiver, which is colored as indicated in the Connection Color Guide Table, above.
The negative terminals on the speakers and the AVR are black.
Digital Audio Connections HDMI

There are two types of audio connections digital and analog. Digital audio signals are
required for listening to sources encoded with digital surround modes, such as Dolby
Digital and DTS, or for uncompressed PCM digital audio. Your AVR has three types of
digital audio connections: HDMI, coaxial and optical. Do not use more than one type of
digital audio connection for each source device. However, its okay to make both analog
and digital audio connections to the same source.
Your AVR uses binding-post speaker terminals that can accept bare-wire cables or
banana plugs. Bare-wire cables are installed as shown below:
Your AVR is equipped with ve rear-panel HDMI input connectors, and one HDMI monitor
output connector. (The AVR 3650 and AVR 365 also have a front-panel HDMI input
connector.) HDMI technology enables digital audio and video information to be carried
using a single cable, delivering the highest quality picture and sound. If your TV or video
display device has an HDMI input connector, make a single HDMI connection from each
source device to the AVR. Usually, a separate digital audio connection is not required.
1. Unscrew Cap
2. Insert Bare Wire
The AVRs HDMI monitor output connection contains an Audio Return Channel (ARC) that
carries a digital audio signal from your TV or video display back to the AVR. It allows
you to listen to HDMI devices that are connected directly to your TV (such as an Internet
connection) without making an additional connection from the device to the AVR. The
ARC signal is active when the TV source is selected. See System Settings, on page 39,
for more information.
3. Tighten Cap
Banana plugs are inserted into the hole in the middle of the terminal cap, as shown
below:
A. Tighten Cap
The HDMI connector is shaped for easy plug-in (see illustration, below), and HDMI cable
runs are limited to about 10 feet (3m). If your video display has a DVI input and is
HDCP-compliant, use an HDMI-to-DVI adapter (not included), and make a separate audio
connection.
B. Insert Banana Connector

p
into Hole in Cap
Always connect the colored (+) terminal on the AVR to the (+) terminal on the speaker
(usually red), and the black () terminal on the AVR to the () terminal on the speaker
(usually black).
IMPORTANT: Make sure the ( + ) and ( ) bare wires do not touch each other or
the other terminal. Touching wires can cause a short circuit that can damage your
receiver or amplier.
12
AVR 2650
harman/kardon
AVR
Digital Audio Connections Coaxial
Video Connections
Coaxial digital audio jacks are usually color-coded in orange. Although they look like
standard RCA-type analog jacks, you should not connect coaxial digital audio outputs to
analog inputs or vice versa.
Many source devices output both audio and video signals (e.g., Blu-ray Disc, DVD
player, cable television box, HDTV tuner, satellite box, VCR, DVR). In addition to an audio
connection as described above, make a video connection for each of these source
devices. Make only one type of video connection for each device.
Digital Video Connections
If you have already connected a source device to one of the AVRs HDMI input connectors,
you have automatically made a video connection for that device, since the HDMI cable
carries both digital audio and digital video signals.
Analog Video Connections Composite Video
Your AVR uses two types of analog video connections: composite video and component
video.
Digital Audio Connections Optical

Optical digital audio connectors are normally covered by a shutter to protect them from
dust. The shutter opens as the cable is inserted. Optical input connectors are colorcoded using a black shutter, while optical outputs use a gray shutter.
Composite video is the basic connection most commonly available. Both the chrominance
(color) and luminance (intensity) components of the video signal are transmitted using a
single cable. The jack is usually color-coded yellow and looks like an analog audio jack.
Do not connect a composite video jack to an analog audio or coaxial digital audio jack,
or vice versa.
Analog Audio Connections

Two-channel analog connections require a stereo audio cable, with one connector for
the left channel (white) and one for the right channel (red). These two connectors are
attached to each other.
Analog Video Connections Component Video

Component video separates the video signal into three components one luminance
(Y) and two sub-sampled color signals (Pb and Pr) that are transmitted using
three separate cables that are color-coded green (Y), blue (Pb) and red (Pr). Component
video cables that join three separate green, blue and red connectors into a single cable
are sold separately.
For source devices that have both digital and analog audio outputs, you may make both
connections. If you are going to be setting up a multizone system, remember that Zone
2 is an audio-only zone (the AVR does not have a Zone 2 video output). Therefore, make
analog connections for any audio source devices (such as a CD changer) that you will
want available for listening in Zone 2 at all times.
The analog connections also feed the analog record outputs. You may record materials
from Blu-ray Disc recordings, DVDs or other copy-protected sources using only analog
connections. Remember to comply with all copyright laws if you choose to make a copy
for your own personal use.
If your TV or video display has an HDMI connection, we recommend it as the best quality
connection. Your AVR converts composite and component analog video input signals to
the HDMI format, upscaling them to high-denition 1080p resolution.
The Bridge IIIP Connection

Your AVR includes a proprietary, dedicated connector for an optional The Bridge IIIP
docking station for the iPod or iPhone. The Bridge IIIP outputs analog audio to the AVR
and is available as a source to Zone 2 in a multizone system.
13
15
AVR 2650
harman/kardon
AVR
Radio Connections
USB Port
Your AVR uses separate terminals for the included FM and AM antennas. The FM antenna
uses a 75-ohm F-connector.
The USB port on your AVR is used for rmware upgrades. If an upgrade for the AVRs
operating system is released in the future, you will be able to download it to the AVR using
this port. Complete instructions will be provided at that time.
In addition to performing rmware upgrades, the AVR 3650/AVR 365 can play MP3 and
WMA audio les from a USB device inserted into the USB port. Insert the device into the
USB port with the devices plug oriented so it ts all the way into the port. You may insert
or remove the device at any time there is no installation or ejection procedure.
The AM antenna connector uses spring-clip terminals. After assembling the antenna as
shown below, press the levers to open the connectors, insert the bare wires into the
openings, and release the levers to secure the wires. The antenna wires are not polarized,
so you can insert either wire into either connector.
IMPORTANT: Do not connect a PC or other USB host/controller to the AVRs USB

port, or you may damage both the AVR and the other device.
RS-232 Connector
SIRIUS Satellite Radio
Your AVRs RS-232 serial port may be connected to an external control system to allow
it to transmit control commands to the AVR. The port is bidirectional so that the AVR
can transmit status updates to the control device. Connecting and using the RS-232
port requires considerable technical knowledge and is best left to a professional custom
installer.
To enjoy SIRIUS satellite radio, purchase a SIRIUSConnect tuner module and a subscription
to the SIRIUS service. Visit www.sirius.com for information on SIRIUSConnect tuner
modules. The SiriusConnect modules include an eight-pin DIN cable for connection to
the eight-pin jack on the AVR, allowing you to control the tuner module via the AVR.
Although you may also use a plug-and-play tuner module equipped with standard
audio connections, you will not be able to use the AVR to control the SIRIUS tuner.
Network Connector
The AVRs Network connector allows you to enjoy Internet radio or content from other
DLNA-compatible devices that are connected to the same network. Use a Cat. 5 or
Cat. 5E cable to connect the AVRs RJ-45 connector to your home network.
14
AVR 2650
harman/kardon
AVR
Making Connections
Making Connections
Connect Your Subwoofer
CAUTION: Before making any connections to the audio/video receiver, ensure

that the AVRs AC cord is unplugged from the receiver and the AC outlet.
Making connections with the receiver plugged in and turned on could damage
the speakers.
Use a single RCA audio cable to connect the AVRs Subwoofer connector to your
subwoofer as explained in Subwoofer Connections, on page 14. Consult your subwoofers
user manual for specic information about making connections to it.
AVR Subwoofer
AVR Subwoofer
Connector
Connector
Connect Your Speakers

After you have placed your loudspeakers in the room as explained in Place Your Speakers,
on page 13, connect each speaker to its color-coded terminal on the AVR as explained
in Speaker Connections, on page 14. Connect the speakers as shown in the illustration.
Single
Single
RCA Audio Cable
RCA Audio Cable
(notsupplied)
(not supplied)
Powered
Powered
Subwoofer
Subwoofer
Connect Your TV or Video Display

If your TV has an HDMI connector: Use an HDMI cable (not included) to connect it to the
AVRs HDMI Monitor Out connector. You do not need to make any other connections to
your TV from the receiver or from any of your video source components.
Receiver
HDMI Monitor Out
HDMI Monitor Out
Connector
Connector
TV
HDMI Cable
HDMI Cable
(not supplied)
(not supplied)
If your TV does not have an HDMI connector: Use a composite video cable (not
included) to connect the AVRs Composite Monitor Out connector to your TVs composite
video connector.
Receiver
Composite
Composite
Monitor Out
Monitor Out
Connector
Connector
TV
Composite Video Cable

Composite
(not supplied)
Video Cable
(not supplied)
NOTE: If you installed front height speakers, connect them as shown for the SBL and
SBR speakers.
NOTE: The HDMI connection to your TV is preferred. If you use the composite video
connection to your TV, you will not be able to view the AVRs on-screen menus.
15
AVR 2650
harman/kardon
AVR
Making Connections
Connect Your HDMI Devices
Connect Your Optical Digital Video Devices
If any of your source devices have HDMI connectors, using them will provide the best
possible video and audio performance quality. Since the HDMI cable carries both digital
video and digital audio signals, you do not have to make any additional audio connections
for devices you connect via an HDMI cable.
If your non-HDMI source devices have optical digital outputs, connect them to the AVRs
optical digital audio connectors. NOTE: Make only one type of digital connection (HDMI,
optical or coaxial) from each device.
Receiver
Digital Audio Connectors
Receiver
HDMI Connectors
Optical Digital Audio

Opticalsupplied) Audio
Digital
Cable (not
Cable (not supplied)
HDMI Cable
(not supplied)
HDMI Cable
(not supplied)
ToOptical DigitalDigital
Optical Audio
To
Output
Audio Output
ToHDMI
To HDMI
Output
Output
Optical Digital-Equipped
Source Device
HDMI-Equipped
Source Device
Connect Your Coaxial Digital Audio Devices
NOTE: If you have HDMI devices (such as an Internet connection) already connected
directly to your TV, you can feed their sound to the AVR via the HDMI Monitor Out
connectors Audio Return Channel, and they will not require additional connections to
the AVR.
If your non-HDMI source devices have coaxial digital outputs, connect them to the AVRs
coaxial digital audio connectors. NOTE: Make only one type of digital connection (HDMI,
optical or coaxial) from each device.
Receiver
g
Digital Audio Connectors
Connect Your Component Video Devices

If any of your video source devices have component video connectors (and do not have
HDMI connectors), using the component video connectors will provide superior video
performance. You will also need to make an audio connection from the device to the
receiver.
Receiver
Video Connectors
Coaxial Digital Audio

Coaxial Digital
Audio
ToCoaxial DigitalDigital
Coaxial Audio
To
Output
Audio Output
Component Video
Component Video
Coaxial Digital-Equipped
Source Device
To Component Video
To Component Video
Outputs
Outputs
Connect Your Analog Audio Devices

Use the AVRs analog audio connectors for source devices that dont have HDMI or digital
audio connectors. NOTE: If youre installing a multizone system, make analog audio
connections for any source devices you want to be able to listen to in Zone 2. Only analog
sources are available in Zone 2.
Component Video-Equipped
Source Device
Connect Your Composite Video Devices
Receiver
Receiver
Analog Audio Connectors
Analog Audio Connectors
Use composite video connectors for video source devices that dont have HDMI or
component video connectors. You will also need to make an audio connection from the
source device to the receiver.
Receiver
Video Connectors
Stereo Audio
Stereo(not supplied)
Cable Audio Cable
(not supplied)
Composite Video
Composite Video
To Stereo Analog
Audio Output
To Stereo Analog Audio

Output
ToComposite Video Video

Composite
To
Output
Output
Analog Source Device

Composite Video-Equipped
Source Device
16
19
AVR 2650
harman/kardon
AVR
Making Connections
Connect Your Audio Recorders
Connect The Bridge IIIP
Connect a digital audio recorders optical digital input to the AVRs optical digital output.
You can record both coaxial and optical digital audio input signals.
Connect an optional The Bridge IIIP to the AVRs The Bridge IIIP connector. Insert the plug
until it snaps into place in the connector. IMPORTANT: Connect The Bridge IIIP only
with the AVRs power turned OFF.
Receiver
Digital Audio Recorder Connector
AVR
The Bridge IIIP
Connector


ToOptical Digital Digital
Optical
To
Record Input
Record Input
Digital
Recording Device
Connect an analog audio recorders inputs to the AVRs analog audio Rec Out connectors.
You can record any analog audio input signal.
The Bridge IIIP

The BridgeIIIP
Receiver
Analog Audio Recorder Connectors
Dock your iPod or iPhone (not included) in The Bridge IIIP, and you may listen to its audio
through your high-performance audio/video system. You may also view still images or
video materials stored on a photo- or video-capable iPod or iPhone that supports video
browsing. You can use the AVR remote to control the iPod, with navigation messages
displayed on the AVRs front panel and on a video display connected to the AVR.
Connect to Your Home Network

Use a Cat. 5 or Cat. 5E cable (not supplied) to connect the AVRs Network connector to
your home network to enjoy Internet radio and content from DLNA-compatible devices
that are connected to the network.
Stereo Audio
Stereo Audio
Receiver
Receiver
Network
Network
Connector
Connector
ToStereo Analog Analog

Stereo Record
To
Inputs
Record Inputs
Network
Network
Modem
Modem
Analog
Recording Device
Cat. 5/5E Cable
(not supplied)
Cat. 5/5E Cable

(not supplied)
Connect Your Video Recorder

Connect an analog video recorders video input connector to the AVRs Composite Video
Rec Out connector. You can record any composite video signal. NOTE: To record the audio
and video from the source device, connect the AVRs analog audio Rec Out connectors to
the analog video recorders audio inputs.
Connect the Radio Antennas

Connect the supplied FM antenna to the AVRs FM 75 antenna connector. For the best
reception, extend the FM antenna as far as possible.
Receiver Analog Video

Recorder Connectors
Bend and fold the base of the supplied AM antenna as shown and connect the antenna
wires to the AVRs AM and Gnd connectors. (You can connect either wire to either
connector.) Rotate the antenna as necessary to minimize background noise.
Receiver Analog Audio

Recorder Connectors
Analog Audio/Video
AVR
Antenna
Connectors
To Analog
Audio/Video
Record Inputs
FM Antenna (supplied)
Analog Video
Recording Device
20
To
To
Internet
Internet
and LAN
and LAN
AM Antenna
(supplied)
17
Bend and fold base
AVR 2650
harman/kardon
AVR
Making Connections
Connect a SIRIUSConnect Radio Tuner (AVR 3650 and AVR 2650 only)
Install a Multizone System
Connect the multi-pin DIN cable supplied with the SIRIUSConnect tuner to the AVRs
SIRIUS Tuner connector and to the corresponding connector on the SIRIUS module. The
AVR will supply power to the SIRIUS module so you will not need to connect the power
supply included with the module. You will need to purchase a SIRIUS radio subscription
and activate the tuner module, following the instructions included with the SIRIUS module
and from the SIRIUS Web site at www.sirius.com.
AVR
SIRIUS Tuner
Connector
SIRIUSConnect Tuner
Eight-Pin DIN Cable

(supplied with SIRIUS tuner)
18
AVR 2650
harman/kardon
AVR
Operating Your AVR
Operating Your AVR

Now that you have installed your components and completed a basic conguration, you
are ready to begin enjoying your home theater system.
Setting
Effect
Controlling the Volume
Off
No Dolby Volume processing
Low
Only Dolby Volume Modeler module is active
Medium
Both Modeler and Leveler modules are active;

Leveler module has a value of 3
Max
Both Modeler and Leveler modules are active;

Leveler module has a value of 9
Adjust the volume either by turning the front-panel Volume knob (clockwise to increase
volume or counterclockwise to decrease volume) or by pressing the Volume Up/Down
buttons on the remote. The volume is displayed as a negative number of decibels (dB)
below the 0dB reference point (-90dB +10dB).
0dB is the maximum recommended volume for your AVR. Although its possible to turn
the volume to a higher level, doing so may damage your hearing and your speakers. For
certain more dynamic audio materials, even 0dB may be too high, allowing for damage
to equipment. Use caution with regard to volume levels.
NOTE: Dolby Volume processing is compatible with sources recorded at a sampling

rate of 48kHz. High-resolution sources, such as DTS 96/24 programs, will be
decoded at 48kHz. DTS 96/24 programs will be played in DTS 5.1 mode. To hear
DTS 96/24 materials in high resolution, turn off Dolby Volume processing.
To change the volume level display from the default decibel scale to a 0-to-90 scale,
adjust the Volume Units setting in the System Settings menu, as described in System
Settings, on page 39.
Muting the Sound

To mute all speakers and the headphones, press the Mute button on the remote. Any
recording in progress will not be affected. The MUTE message will appear in the display
as a reminder. To restore the sound, press the Mute button again, or adjust the volume.
Dolby Volume
Your AVR implements Dolby Volume processing, which can improve the audio performance
of the system by revealing subtle details in the sound, even at normal home-listening
volumes.
One concern of the typical home theater listener is that volumes can vary widely for
different programs played by a source (e.g., television commercial advertisements are
often much louder than the main program). Another is that details heard in the recording
studio at typically high reference volumes are lost at the lower volumes used by many
listeners at home.
The AVR uses two Dolby Volume techniques to address these issues. The Leveler module
maintains a consistent listening volume within a source (e.g., commercial television or
different tracks on a USB drive or mix CD). The Modeler module endeavors to re-create
the reference presentation that was heard in the recording studio without losing portions
of the program at the typically lower volume levels often used in the home. When the
Modeler module is active, you may notice details of the performance that were hidden
when the program was played on other equipment.
To adjust the Dolby Volume setting, press the Audio Effects button. The Audio Effects
submenu will appear.
Audio Effects Cable/Sat
Dolby Volume calibration allows you to adjust the operation of the Dolby Volume
circuitry to match your particular speakers and listening environment. The Dolby Volume
circuitry in your AVR is factory-calibrated with average speaker sensitivity in mind;
however, different speakers may have different sensitivities, which will affect the overall
performance of the Dolby Volume circuitry. Use Dolby Volume calibration to adjust the
calibration of the circuitry according to the specic speakers you have.
The average home audio speaker sensitivity is 88dB SPL (1 watt/1 meter). Check the
sensitivity specication for your loudspeakers, found in the owners manual or on the
manufacturers Web site. If your speakers have a sensitivity rating greater than 88dB SPL,
increase Dolby Volume calibration by the difference between your speakers sensitivity
and 88dB. If they have a sensitivity rating of less than 88dB SPL, decrease Dolby Volume
calibration by the difference between your speakers sensitivity and 88dB.
To adjust the Dolby Volume calibration, press the AVR button and select the System
menu. Scroll to the Dolby Volume calibration line, which defaults to 0dB. Use the Left/
Right buttons to adjust the setting within the range of 10dB to +10dB.
Listening Through Headphones

Plug the 1/4-inch stereo plug on a pair of headphones into the front-panel Phones jack
for private listening. The default Headphone Bypass mode delivers a conventional twochannel signal to the headphones. Press the Surround Modes button on the front panel
or the remote to switch to HARMAN headphone virtual surround processing, which
emulates a 5.1-channel speaker system. No other surround modes are available for the
headphones.
Selecting a Source
Dolby Volume:
PLIIz Height Gain:
Edit: Dolby PLII Music
Edit: Dolby PLIIx Music
Medium
Low
Tone Control:
Treble:
Bass:
LFE Trim:
On
MP3 Enhancer
EZSET/EQ:
Dolby Volume Calibration
There are three different ways to select a source:

Press the front-panel Source List button. Use the Up/Down buttons to scroll through the
sources, and press the OK button to select the source being displayed.
Using the on-screen menus, press the AVR button, highlight Source Select and press
the OK button. Scroll to the desired source in the slide-in menu and press the OK button.
You can directly select any source by pressing its Source Selector button on the remote.
Off
Off
The AVR selects the audio and video inputs assigned to the source, and any other settings
you made during setup.
The source name, the audio and video inputs assigned to the source, and the surround
mode will appear on the front panel. The source name and active surround mode will also
briey appear on the TV screen.
After you highlight the Dolby Volume setting, each press of the OK button will switch to
one of the options in the table below. The settings do not refer to the volume level, which
is adjusted normally using the AVRs Volume Control, but rather to the amount of Dolby
Volume processing desired.
19
AVR 2650
harman/kardon
AVR
Operating Your AVR
Listening to SIRIUS Satellite Radio

SIRIUS Satellite Radio delivers a variety of commercial-free music from categories
including pop, rock, country, R&B, dance, jazz, classical and many more, plus
coverage of all the top professional and college sports, including play-by-play games
from select leagues and teams. Additional programming includes expert sports talk,
uncensored entertainment, comedy, family programming, local trafc and weather,
and news from your most trusted sources. SIRIUS Satellite Radio is available to
residents of the U.S. (except Alaska and Hawaii) and Canada.
Video Troubleshooting Tips

If there is no picture:
Check the source selection and video input assignment.
Check all connections for a loose or incorrect connection.
Check the video input selection on the TV/display device.
To listen to SIRIUS Satellite Radio, youll need to connect a SIRIUS tuner module (sold
separately) to the AVRs SIRIUS Tuner connector. SIRIUS tuner modules that will work
with your AVR are available at www.sirius.com. Select a tuner module designated
for SIRIUS-Ready audio components (also called SIRIUSConnect). A SIRIUSConnect
module is controlled by the AVRs internal tuner, including 40 preset SIRIUS station
locations and remote control. Although you may also use a SIRIUS plug-and-play
unit with standard analog audio connections, you will not be able to enjoy the AVRs
ease of control.
Press the front-panel Resolution button and use the Up/Down buttons until the
correct video output resolution is selected and a picture appears. The CANCEL
message will also appear. Press the Down button to view the ACCEPT option, then
press the OK button.
Additional Tips for Troubleshooting HDMI Connections
Turn off all devices (including the TV, the AVR and any source components).
Unplug the HDMI cables, starting with the cable between the AVR and the TV, and
continuing with the cables between the AVR and each source device.
Installing the SIRIUS tuner module

Once youve purchased a SIRIUS tuner, youll need to install it, activate it and
subscribe to begin enjoying the service:
Carefully reconnect the cables from the source devices to the AVR. Connect the
cable from the AVR to the TV last.
Turn on the devices in this order: TV, AVR, source devices.
1. Using the cable included with the SIRIUS tuner module, plug the module into the
SIRIUS Tuner connector on the rear of the AVR.
NOTE: Depending upon the particular components involved, the complexity of

the required communication between HDMI components may cause delays of
up to a minute in the completion of some actions, such as input switching or
switching between SD and HD channels.
2. Follow the instructions included with the SIRIUS tuner module to complete its
installation. NOTE: Pay particular attention to the instructions for installing and
orienting the SIRIUS antenna that is included with the SIRIUS tuner module.
3. Call 1-888-539-SIRI (7474) or visit sirius.com (U.S.) or siriuscanada.ca (Canada) to
activate your SIRIUS tuner module and subscribe to the SIRIUS service.
Listening to FM and AM Radio
To listen to SIRIUS radio
Select the Radio source. A screen similar to the one in the illustration below will appear.
(Note: The SIRIUS band uses a different screen.)
Select SIRIUS Radio as the source in one of these ways:

Press the Source List button on the front panel. Use the Up/Down buttons to scroll
to SIRIUS Radio and press the OK Button.
Press the Radio Source Selector button on the remote repeatedly until SIRIUS Radio
is selected.
AM/FM Radio
There are four ways to tune a SIRIUS radio channel:

1
FM
Use the Up/Down buttons or the Channel Up/Down buttons to scan through the
channel numbers.
87.50 MHz
Auto
Use the Left/Right buttons to scan through any previously programmed preset
stations.
Menu:
MENU
Set Presets:
OK
Presets:
After you have programmed presets, directly enter the preset number (1 through
40) using the Number buttons. For two-digit positions, enter a 0 before the number.
Use the Up/Down buttons or the Remotes Channel buttons to tune a station (or
channel for SIRIUS Radio), as displayed on the front panel and on-screen display.
The AVR defaults to automatic tuning, meaning each press of the Up/Down buttons
scans up or down the frequency band until a station with acceptable signal strength
is found. To switch to manual tuning, in which each press of the Up/Down buttons
steps through a single tuning frequency increment, press the remotes Menu button.
A slide-in menu will appear. Select Mode, and press the OK button to toggle
between automatic and manual tuning modes.
Once you have tuned an FM station, toggling the Mode setting also switches the radio
between stereo and monaural reception. (Mono reception may improve reception of
weaker stations.)
To search for a channel, press the Menu button, then use the Up/Down buttons to
cycle through the following choices: Preset, Category, All Channels or Direct Entry.
Press the OK button to select one, then use the Up/Down buttons to search for the
channel (for Direct Entry, use the Number buttons to enter the channel number), then
press the OK button.
The current channel number and preset location will appear in the lower line of the
AVRs front-panel Message Display. The song title, artist, channel name, channel
category, channel number, preset position (if programmed) and signal-strength bars
will all appear on the screen when a video display is in use. For trafc and weather
channels, the current citys name will appear instead of the channel name.
Preset SIRIUS channels
Preset Stations
You can store a total of 30 stations (AM and FM combined) as presets. When you
want to save the currently tuned station as a preset, press the OK button, and two
dashes will ash. Use the Number buttons to enter the desired preset number.
You can store a total of 40 channels as presets. When the desired channel has
been tuned, press the OK button, and two dashes will ash on the AVRs front-panel
Message Display. Use the Number buttons to enter the desired preset number.
To tune to a preset SIRIUS channel:
To tune to a preset station:
Press the Left/Right buttons.
Press the Left/Right buttons.
Press the skip forward/skip backward Transport Control buttons.
Press the skip forward/skip backward Transport Control buttons.
Press the Menu Button and scroll to the desired preset, then press the OK Button.
Press the Menu button and scroll to the desired preset, then press the OK button.
Enter the preset number using the Number buttons. For presets 10 through 30,
press 0 before the preset number. For example, to enter preset 21, press 0-2-1.
20
Enter the preset number using the Number buttons. For presets 10 through 40,
press 0 before the preset number. For example, to enter preset 21, press 0-2-1.
29
AVR 2650
harman/kardon
AVR
Operating Your AVR
Listening to Media on a USB Device (AVR 3650/AVR 365)
Listening to an iPod/iPhone Device
Your AVR is compatible with MP3 and WMA media.
When The Bridge IIIP is connected to its proprietary input on the AVR and an iPod
or iPhone is docked, you may play the audio, video and still-image materials on
your iPod or iPhone through your high-quality audio/video system, operate the iPod
or iPhone using the AVR remote or the AVRs front-panel controls, view navigation
messages on the AVRs front panel or a connected video display and charge the iPod
or iPhone.
MP3 compatibility: Mono or stereo, contstant bit rates (CBR) from 8kbps to
320kbps, variable bit rates (VBR) from lowest to highest quality, with sample rates
from 8kHz 48kHz.
WMA compatibility: Ver. 9.2, stereo CBR with 32kHz 48kHz sampling rate and
40kbps 192kbps bit rate, mono CBR with 8kHz 16kHz sampling rate and 5kbps
16kbps bit rate, VBR Pass Encoding and Quality Encoding 10 98, 44kHz and 48kHz
sampling rate.
As of this writing, your AVR supports audio, video and photo playback from the
following Apple products: iPod classic, iPod nano 3G, iPod nano 4G, iPod nano 5G,
iPod nano 6G, iPod touch, iPod touch 2G, iPod touch 3G, iPod touch 4G, iPhone,
iPhone 3G, iPhone 3GS, iPhone 4G. For the latest compatibility information, please
see our Web site: www.harmankardon.com.
No other types of media can be played.

Playing les on a USB device
When you select The Bridge Source Selector button on the remote, Bridge will
appear on the front-panel display, a The Bridge screen will appear and the slide-in
menu will automatically appear.
1. Insert the USB drive into the AVRs front-panel USB port.
IMPORTANT: Do not connect a personal computer or peripheral to the USB port. USB
hubs and multi-card readers are not supported.
2. Select the USB Source Selector button on the remote. USB will appear on the
front-panel display, and the USB screen and the slide-in menu will appear.
The Bridge
The Bridge
Music
Photos/Manual
Videos
Random: Off
Repeat: Off
USB
USB
Browse USB
Repeat Music: Off
Menu:
Menu:
MENU
Previous:
Previous:
MENU
Next:
NOTE: If the AVR doesnt detect the iPod or iPhone, turn off the AVR, remove the iPod
or iPhone from The Bridge IIIP and reset the iPod or iPhone. When the iPod or iPhone
returns to its main menu, re-dock it and turn on the AVR.
Next:
The table below summarizes the controls available during normal playback with The
Bridge IIIP:
3. Select Browse USB. The AVR will list the folders located on the drive.
4. Select a folder and press the OK button. The AVR will list all compatible audio les.
5. Select a le to begin playback. The USB play screen will appear. Any ID3
information and album art will be displayed, along with the tracks elapsed/current
time and icons indicating the current playback status.
iPod or iPhone Function

Play
Scroll Reverse
Previous:
Down Arrow
Forward Search
Forward Search
Reverse Search
Next Track
Skip Forward or Right Arrow
Previous Track
Skip Backward or Left Arrow
Page Up/Down
Next:
Up Arrow
Reverse Search
MENU
OK or Right Arrow
Scroll Forward
Menu:
Back/Exit or Left Arrow
Select
06:16/17:17
Menu
Back/Exit
Jugalbandi
Night Crazy
Pause
Menu
Night Crazy
Play
Pause
USB
Remote Control Key
Page Up/Down
NOTES:
To skip to the next track, press the Right button; to return to the previous track,
press the Left button once.
You can use the Transport Control buttons to control playback (skipping to the
previous or next track, searching at high speed forward or backward within a track,
playing a le, pausing playback or stopping playback).
While scrolling, hold the button to scroll faster. Use the Page Up/Down control on the
remote to scroll a page at a time.
To repeat a le or folder, press the Menu Button and select the Repeat option.
Each press of the OK Button will change the setting from Off (no repeat) to Repeat
One (le) to Repeat All (les at the current directory level of the drive). Repeat All will
always be activated when Random Music playback is turned on.
While a selection is playing, the album, artist, song title, track elapsed time, total track
time and play mode icon will appear on the front-panel Message display.
To play the audio tracks in random order, press the Menu button and select the
Random Music setting. Each press of the OK button turns the setting on or off. The
AVR will automatically repeat the tracks until playback is stopped manually.
To collapse a folder or return to the previous menu level, press the Back/Exit button
or the Left button.
21
30
AVR 2650
harman/kardon
AVR
Operating Your AVR
If a video monitor is connected to the AVR and the system is not in iPod manual mode,
a The Bridge screen will appear and display the play mode icon, song title, artist and
album. A graphic bar indicates the current play position within the track. If random or
repeat play has been programmed, an icon will appear in the upper right corner.
The AVR supports audio playback from some applications available for the iPhone
and the iPod touch. Place the system in iPod manual mode by pressing the Menu
button and selecting Photo/Manual. Then use the controls on the iPhone or iPod
touch to run the application.
Due to the wide variety of applications and many factors affecting them, playback
is not guaranteed.
The Bridge
NOTES:
The Play and Pause functions are not available unless content has been selected
for playback.
The Lost Transit Center

Jugalbandi
Night Crazy
To search within a track, press and hold the forward or reverse Transport Control
button. Press the previous track Transport Control button once to skip to the beginning
of the current track; press the previous track Transport Control button twice to skip to
the beginning of the previous track.
03:41/10:44
Menu:
MENU
Previous:
Next:
Listening to Internet Radio

The screen may disappear from view, depending on the Setup and Slide-In Menus
setting in the System Settings menu (described in System Settings, on page 39). You
can restore the Now Playing screen to view by pressing either of the Left or Right
buttons.
Your AVRs Network connection brings you a world of MP3- and WMA-format streams
via the Internet. After you have successfully connected to your home network as
described in Connect to Your Home Network, on page 20, and set up the network
as described in Set Up the Network, on page 27, press the Network Source Selector
button on the remote. Each press toggles between the Network and Internet Radio
screens.
CAUTION: We strongly recommend that you use the screen saver built
into your video display to avoid possible damage from burn-in that may
occur with plasma and many CRT displays when a still image, such as a
menu screen, remains on the display for an extended period of time.
Internet Radio
Press the Menu button to view the slide-out menu:
Big Blue Swing

Count Basie
Music: Select this to navigate the audio materials stored on the iPod or iPhone. Use
the Page up/down buttons on the remote to scroll through the content a page at a
time.
Menu:
Photo/Manual: Select this to view still images stored on a photo-capable iPod or

iPhone. The system will switch to iPod manual mode, and control will shift to the
iPod. Use the screen and controls on the iPod. The AVR remote may also be used. To
view photos on a video monitor connected to the AVR, select the photo and press the
Play button on the iPod, or press the OK button on the remote three times.
Videos: Select this to view videos stored on an iPhone or an iPod that supports video
browsing.
Notes on iPod/iPhone video playback:
Before attempting to view photos or videos stored on your device, check the Video
Settings menu on the device and make sure that the TV Out setting is set to On. The
TV Signal setting should be set to match the capabilities of your video display (NTSC
for the US; PAL for the EU). If your selection was playing and is paused, the iPod or
iPhone requires you to reselect the video for the new TV Out setting to take effect.
If you do not see the Videos line in the menu, and the iPod supports video browsing
and has video content stored on it, you may need to turn off the AVR, remove the iPod
from The Bridge IIIP, reset the iPod, turn the AVR back on and dock the iPod again. An
iPhone may not need to be reset, as simply undocking and re-docking it may resolve
the problem. This procedure may also help when a video program is selected but the
Bridge screen appears instead of the video images.
To exit iPod manual mode, with the AVR remote in The Bridge mode, press the Menu
button. To return to a previous menu level, press the Back/Exit Button or the Left
button.
Repeat: Select this setting to repeat a track or all tracks in the current album or
playlist. Each press of the OK button switches the setting: repeat Off, repeat One or
repeat All.
Random: Select this setting for random playback, also known as Shufe Mode.
Each press of the OK button switches the setting: shufe by Song, shufe by Album,
or Off to end random playback.
NOTE: The iTunes application allows you to exempt some tracks from Shufe mode.
The AVR cannot override this setting.
22
MENU
Set Presets:
OK
Presets:
With the Internet Radio screen (above) displayed, the AVR will automatically connect
to the Internet via the www.radioharmankardon.com portal. To select a stream, press
the Menu button, and use the Up/Down buttons to search by category: Presets, My
Favourites, Local Stations, HDi, Stations, Podcasts or My Added Stations. NOTE: The
categories displayed may vary by region.
To create a Favourites list, log onto www.radioharmankardon.com from your
computer. Enter your AVRs ID # (to see the ID # with the Internet Radio screen
displayed, press the Menu button, then select Help) and create an account. Favourites
that you select on the Web site will be available on the AVR.
NOTE: While the Help screen is displayed, we recommend spending a few moments
listening to the audio FAQs to get answers to common questions about Internet radio
operation. The FAQs play in a continuous loop. To return to an Internet radio station
while an FAQ is playing, press the Menu button, then the Back/Exit button, then the
Back/Exit button again, and select an Internet radio station.
Navigation is similar to other slide-in menus. Scroll to the desired item and press the
OK button or the Right button to select it. To return to the previous menu level (or to
clear the top-level menu from view), press the Back/Exit button or the Left button.
If you know the URL (Web address) of a specic audio stream, select the Direct
Station option from the menu. A live stream is required. The AVR is not able to
connect to streams that require site registration or other interaction prior to playing
the stream. If the AVR cannot connect to the stream, a Station Not Live message
will appear briey, and the Internet Radio screen will remain essentially blank. Not
all URLs will be accessible.
Internet Radio Presets
You can program up to 30 Internet radio stations as presets. To set a preset, rst tune
the station. Press the OK button, and two dashes will ash. Enter the preset number
(any number from 1 through 30) using the Number buttons. The connection to the
station will momentarily stop, interrupting the program, and the AVR will reconnect
to the station.
To connect to a station programmed as a preset, enter its preset number using the
Number buttons, or use the Left/Right buttons to select it from the preset list.
31
AVR 2650
harman/kardon
AVR
Operating Your AVR
certain sources or program types. You can nd more detailed information on surround
modes in Audio Processing and Surround Sound, on page 33.
Listening to Media via Your Home Network

Your AVR can play MP3 and WMA audio media that is stored on a PC when both the
PC and the AVR are connected to your home network router.
To select a surround mode, press the Surround Modes button (front panel or remote).
The Surround Modes menu will appear.
MP3 compatibility: Mono or stereo, contstant bit rates (CBR) from 8kbps to
320kbps, variable bit rates (VBR) from lowest to highest quality, with sample rates
from 8kHz 48kHz.
Surround Modes Cable/Sat

Auto Select AVR Selects Best Mode
Virtual Surround For Two Speaker Systems
Stereo:
2 CH Stereo
Movie:
Logic 7 Movie
Music:
Logic 7 Music
Video Game:
Logic 7 Game
WMA compatibility: Ver. 9.2, stereo CBR with 32kHz 48kHz sampling rate and
40kbps 192kbps bit rate, mono CBR with 8kHz 16kHz sampling rate and 5kbps
16kbps bit rate, VBR Pass Encoding and Quality Encoding 10 98, 44kHz and 48kHz
sampling rate.
NOTES:
A PC must be running Windows Media Player version 11 or higher, Windows
Media Center version 2.0 or 3.0, or Intel Media Server. We recommend that any
rewalls be turned off, although Windows Media Player may automatically make
any necessary adjustments to the rewall settings to allow media sharing.
Press the Up/Down buttons repeatedly until the desired surround-mode category
appears: Auto Select, Virtual Surround, Stereo, Movie, Music or Video Game. Press
the OK button to change the surround-mode category.
An Apple Macintosh computer must be running DLNA (Digital Living Network

Alliance)-compliant software. Examples of compatible software include the
TwonkyServer program by PacketVideo, and EyeConnect software by Elgato
Systems.
Auto Select: For digital programs, such as a movie recorded with a Dolby Digital
or DTS soundtrack, the AVR will automatically use the soundtracks native surround
format. For two-channel analog and PCM programs, the AVR uses the Logic 7 Movie,
Logic 7 Music or Logic 7 Game mode, depending on the source.
Before you can access les located on other devices via the network, each device
must rst give permission to share les with the AVR:
Virtual Surround: When only two main speakers are present in the system, you can
use HARMAN Virtual Surround to create an enhanced soundeld that virtualizes the
missing speakers. Select between Wide and Reference modes.
Stereo: When you want two-channel playback, select the number of speakers you
want to use for playback:
To share media on PCs:

1. Open Windows Media Player.
2 CH Stereo uses two speakers.
2. Open the Library menu and select Media Sharing. The Media Sharing window will
appear.
5 CH Stereo plays the left-channel signal through the front left and surround
left speakers, the right-channel signal through the front right and surround right
speakers, and a summed mono signal through the center speaker.
3. Check the Share My Media box. An icon for the AVR will appear in the window.
4. Select the AVR icon, select Allow, then select OK.
To share media on other types of computers, operating systems or media software:
Check the instructions for the computer, operating system or media player.
7 CH Stereo follows the same scheme as 5 CH Stereo but adds the surround
back left and surround back right speakers. This mode is available only when the
surround back speakers are present and have not been reassigned to multizone or
front height operation. See Audio Processing and Surround Sound, on page 33, for
more information.
To listen to shared media, press the Network Source Selector button. (If Internet
Radio appears as the source, press the button a second time to switch from the
Internet Radio source to the Network source.) The Network screen will appear.
Movie: Select from the following when you want a surround mode for movie
playback: Logic 7 Movie, DTS Neo:6 Cinema or Dolby Pro Logic II (IIx or IIz when
seven main speakers are present).
The computers WMA and MP3 media should now be available to the AVR.
Music: Select from the following when you want a surround mode for music
playback: Logic 7 Music, DTS Neo:6 Music or Dolby Pro Logic II (IIx or IIz when seven
main speakers are present). The Dolby Pro Logic II/IIx/IIz Music mode allows access
to a submenu with some additional settings. See Audio Processing and Surround
Sound, on page 33, for more information.
Network
Beanwater Junction
Jugalbandi
Night Crazy
Video Game: Select from the following when you want a surround mode for game
playback: Logic 7 Game or Dolby Pro Logic II (IIx/IIz when seven main speakers are
present) Game.
01.50/3:55
Menu:
MENU
Previous:
Next:
After you have made your selection, press the Back/Exit button.
See Audio Processing and Surround Sound, on page 33, for more information on
surround modes.
Press the Menu button, and the slide-in menu should list all devices that allow
sharing by name. Use the slide-in menu to browse the content stored in the devices
media player library. Scroll to the desired item and press the OK button or the Right
button to select it. To return to the previous menu level (or to clear the menu from
view from the top level), press the Back/Exit button or the Left button.
Audio Effects
The Audio Effects buttons on the front panel and remote provide settings that let you
adjust the Dolby Volume setting, tone controls, LFE trim, Equalization On/Off setting
or MP3 Enhancement to improve performance. We recommended that you leave
these settings at their default values until you are more familiar with your system.
See Audio Effects Button, on page 34, for complete information.
NOTES:
The Repeat settings are global for Network playback and USB playback. Changing
these settings for one of these sources will change the other sources settings as
well.
Video Modes
Although video content may appear in the menu, the AVR does not support video
playback from the network connection.
The Video Modes buttons on the front panel and remote provide settings that let you
use the AVRs video processor to ne-tune the picture, if necessary, after making all
adjustments on the video display. We recommend that you leave the settings at their
defaults until you are completely familiar with the video performance of your system.
See Video Processing, on page 34, for complete information.
Selecting a Surround Mode

Selecting a surround mode can be as simple or sophisticated as your individual
system and tastes. Feel free to experiment, and you may nd a few favorites for
32
23
AVR 2650
harman/kardon
AVR
Troubleshooting
Symptom
Cause
Solution
Unit does not function when Main Power switch is

turned on
No AC power
Ensure that the power cord is plugged into a live

AC power outlet
Check if the AC outlet is switch-controlled
Front-panel Message display lights, but theres no

sound or picture
Intermittent input connection
Dolby Digital EX
Dolby Digital 2/2/.0 or .1, 3/2/.0 or .1
No sound from any speaker; PROTECT message appears Amplifier is in protection mode due to possible short
on Message display
circuit
Dolby Digital Plus via HDMI connection (source

device decodes to Dolby Digital when a coaxial
or optical connection is used)
No sound from center or surround speakers
Incorrect surround mode
Select a surround mode other than stereo
Program material is monophonic
Mono programs contain no surround information
Incorrect speaker configuration
Check the speaker conguration in the setup

menu
Program material is stereo
The surround decoder may not create center- or

surround-channel information from nonencoded
programs
Weak batteries in remote
Change batteries in remote
AVR not selected
Press the Setup/AVR button
Remote sensor is obscured
Ensure that the AVRs front-panel remote sensor

is in the line of sight of the remote
Intermittent buzzing in tuner
Local interference
Move the AVR or antenna away from computers,

fluorescent lights, motors or other electrical
appliances
(AVR 3650/AVR 365 only): Surround-back speaker

settings cannot be accessed, and the test tone does not
play through the surround back speakers
Multi-zone operation has been selected/Assigned AMP Use the Speaker Setup menu to reassign the
Assigned AMP to the surround back left and right
channels have been assigned to Zone 2
channels
(AVR 3650/AVR 2650 only): The SIRIUS Preview

Channel (001) is silent
SIRIUS tuner is not connected
Ensure that SIRIUS tuner is properly connected
SIRIUS antenna is in an improper location
Re-locate the SIRIUS antenna according to

the recommendations in the SIRIUS tuners
instruction manual. For further help, visit
www.siriusradio.com
Unit does not respond to remote control commands
SIRIUS signal requires a refresh
Visit www.siriusradio.com
Unable to activate remote control Programming mode
Source Selector button is not held for at least 3

seconds
Be sure to hold the Source Selector button for at

least 3 seconds
Remote buttons light, but AVR does not respond
Remote is in Zone 2 mode
Slide Zone Selector switch to the Zone 1 position.
Unable to establish network connection
AVR network programming requires rebooting
Cycle the AVR into the Standby mode, and then turn
it on again
Additional information on troubleshooting possible problems with your AVR and installation-related issues may be found in the list of Frequently Asked
Questions, which is located in the Product Support section of our Web site: www.harmankardon.com
24
43
AVR 2650
harman/kardon
Resetting the Remote

To reset the remote to its factory-default condition, simultaneously press and hold any
Source Selector button and the 0 Number button. When the Program Indicator LED
flashes amber, enter the code 333. When the green LED goes out, the remote control
will be reset.
Processor Reset
If the AVR behaves erratically after a power surge, first turn off the rear-panel Main
Power switch and unplug the AC power cord for at least 3 minutes. Plug the cord back
in and turn the AVR on. If this procedure doesnt help, reset the AVRs processor as
described below.
NOTE: A processor reset erases all user configurations, including video resolution,
speaker and level settings, and tuner presets. After a reset, reenter all of these settings
from your notes in the Appendix worksheets.
To reset the AVRs processor:

1. Press the front-panel Standby/On switch to place the unit in the Standby mode (the
Power Indicator LED will turn amber).
2. Press and hold the front-panel OK button for at least 5 seconds until the
RESET message appears on the front-panel Message display.
NOTE: After performing a processor reset, wait at least 1 minute before pressing any
Source Selector buttons.
If the AVR does not function correctly after a processor reset, contact Harman/kardon at 1-800422-8027
25
AVR 2650
harman/kardon
26
AVR 2650
harman/kardon
EXPLODED VIEW
LARGER PARTS CHART

NEXT PAGE
27
AVR 2650
harman/kardon
28
AVR 2650
harman/kardon
AMPLIFIER SECTION BIAS ADJUSTMENT

Measurement condition
.No input signal or volume position is minimum.
Standard value
.Ideal current = 48mA ( 5%)
.Ideal DC Voltage = 25.92mV ( 5%)
DC EVM
CN66
VR8
PCB)
CN61
VR8
CN64
VR8
CN63
VR8
CN65
VR8
CN62
VR8
CN67
VR8
DC VOLTMETER ; Connect to
CN66(SL),CN61(CEN),CN64(SR),CN63(FL),CN65(SBL
NO.
1
2
3
4
5
6
7
Channel
Front Left
Front Right
Center
Surround Left
Surround Right
Surround Back Left
Surround Back Right
Adjust for
25.92mV ( 5%)
25.92mV ( 5%)
25.92mV ( 5%)
25.92mV ( 5%)
25.92mV ( 5%)
25.92mV ( 5%)
25.92mV ( 5%)
29
Adjustment
CN63
CN62
CN61
CN66
CN64
CN65
CN67
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
AVR 2650
harman/kardon
AVR 2650 ELECTRICAL PARTS LIST

Quantity of all components with a designator = 1 unless otherwise noted
Reference
Designator
Part Number
FRONT PCB ASS'Y

C121
C122
C151
C152
C161
C171
C181
C213
C214
C252
C311
C322
C412
C413
C414
C415
C422
C431
C441
C442
C550
C555
C556
C557
C558
C631
C651
C652
C653
C714
C715
C721
C731
C732
C751
C752
C753
C754
C801
C802
C811
C813
C821
C822
C823
C830
C901
C902
C911
C912
CCBS1H151KBT
CCEA1AH331T
CCFT1H473ZF
CCEA1CKS100T
CCBS1H104ZFT
CCBS1H104ZFT
CCBS1H104ZFT
CCBS1H223ZFT
CCBS1H223ZFT
CCEA1HKS2R2T
CCBS1H102KBT
CCBS1H102KBT
CCBS1H103ZFT
CCEA1JH470TS
CCEA1JH470TS
CCBS1H103ZFT
CCEA1HH4R7T
CCBS1H104ZFT
CCBS1H223ZFT
CCBS1H223ZFT
CCBS1H560JT
CCBS1H560JT
CCEA1AH101T
CCBS1H103ZFT
CCBS1H103ZFT
CCBS1H104ZFT
CCBS1H104ZFT
CCBS1H471KBT
CCBS1H471KBT
CCBS1H223ZFT
CCEA1CKS100T
CCEA1HKS2R2T
CCEA1AH471T
CCBS1H104ZFT
CCBS1C222MXT
CCBS1H102KBT
CCBS1H102KBT
CCBS1H104ZFT
CCEA1EH470T
CCEA1EH470T
CCEA1HH100T
CCBS1H470JT
CCBS1H471KBT
CCBS1H151KBT
CCEA1HH100T
CCBS1H473ZFT
CCEA1HH100T
CCEA1HH100T
CCEA1EH470T
CCEA1EH470T
Description
CIP12357D
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
CAP ,
, CERAMIC(150PF/50V)
CH UP025 B151K-A-B Z
, ELECT(10V/330uF)
KR3-10V331MB(6.3*11L)
, CERAMIC
0.047UF 50V Z
, ELECT(16V/10uF)-S
KC3-16V100MA2(4*5L)
, CERAMIC
0.1UF 50V Z
, CERAMIC
0.1UF 50V Z
, CERAMIC
0.1UF 50V Z
CH UP025 F223Z-A-B J
, ELECT(50V/2.2uF)-S
KC3-50V2R2MA2(4*5L)
, CERAMIC
0.01UF 50V Z
, ELECT
63V/47UF/105'C
, ELECT
63V/47UF/105'C
, CERAMIC
0.01UF 50V Z
, ELECT(50V/4.7uF)
KR3-50V4R7MA(5*11L)
, CERAMIC
0.1UF 50V Z
, CERAMIC(56PF/50V)
CH UP025SL560J-A-B Z
, CERAMIC(56PF/50V)
, ELECT(10V/100uF)
KR3-10V101MA(5*11L)
, CERAMIC
0.01UF 50V Z
, CERAMIC
0.01UF 50V Z
, CERAMIC
0.1UF 50V Z
, CERAMIC
0.1UF 50V Z
, ELECT(16V/10uF)-S
KC3-16V100MA2(4*5L)
, ELECT(50V/2.2uF)-S
KC3-50V2R2MA2(4*5L)
, ELECT(10V/470uF)
KR3-10V471MB(6.3*11L)
CERAMIC
0.1UF 50V Z
CERAMIC(2200PF/16V) CH EP025 B222M-A-B J
CERAMIC(1000PF/50V) CH UP025 B102K-A-B Z
CERAMIC
0.1UF 50V Z
ELECT(25V/47uF)
KR3-25V470MA(5*11L)
ELECT(25V/47uF)
KR3-25V470MA(5*11L)
ELECT(50V/10uF)
KR3-50V100MA(5*11L)
CERAMIC(47PF/50V)
ELECT(50V/10uF)
KR3-50V100MA(5*11L)
CERAMIC(47000PF/50V)CH UP025 F473Z-A-B J
ELECT(50V/10uF)
KR3-50V100MA(5*11L)
ELECT(50V/10uF)
KR3-50V100MA(5*11L)
ELECT(25V/47uF)
KR3-25V470MA(5*11L)
ELECT(25V/47uF)
KR3-25V470MA(5*11L)
47
AVR 2650
Reference
Designator
harman/kardon
Part Number
FRONT PCB ASS'Y

C923
C924
C931
C932
D161
D204
D401
D412
D413
D421
D422
D455
D631
D632
D714
L151
Q104
Q111
Q112
Q113
Q251
Q252
Q721
Q906
Q907
Q941
Q942
Q943
Q944
Q951
Q952
Q954
R101
R102
R103
R113
R201
R202
R203
R211
R213
R214
R251
R252
R312
R313
R314
R315
R316
R322
R323
R324
R325
CCBS1H681KBT
CCBS1H681KBT
CCEA1CH331T
CCEA1CH331T
HVD1N5819T
HVD1SS133MT
CVD1N4003ST
CVDZJ8.2BT
HVDMTZJ27BT
CVDZJ6.8BT
CVDZJ6.8BT
HVD1SS133MT
HVD1SS133MT
HVD1SS133MT
C3A206
HLQ02C100KT
CVTKTC1027YT
HVTKRA107MT
HVTKRC107MT
HVTKRC107MT
HVTKTA1271YT
HVTKRC107MT
HVTKRC107MT
HVTKRA107MT
HVTKRA107MT
HVTKTC2874BT
HVTKTC2874BT
HVTKTC2874BT
HVTKTC2874BT
HVTKRC107MT
HVTKRA107MT
HVTKRC107MT
CRD20TF2200T
CRD20TF6800T
CRD20TJ334T
CRD20TJ102T
CRD20TJ101T
CRD20TJ101T
CRD20TJ101T
CRD20TJ101T
CRD20TJ272T
CRD20TJ272T
CRD20TJ222T
CRD25TJ393T
CRD20TF1001T
CRD20TF1501T
CRD20TF1801T
CRD20TF2701T
CRD20TF3301T
CRD20TF1001T
CRD20TF1501T
CRD20TF1801T
CRD20TF2701T
Description
CIP12357D
CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z
CAP , ELECT(16V/330uF)
KR3-16V331MC(8*11.5L)
KR3-16V331MC(8*11.5L)
DIODE , SCHOTTKY
1N5819
DIODE
1SS133T-77
DIODE , RECT
1N4003
DIODE , ZENER 8.2V
ZJ8.2B 1/2W
DIODE , ZENER
MTZJ27B 1/2W
DIODE , ZENER 6.8V
ZJ6.8B 1/2W
DIODE , ZENER 6.8V
ZJ6.8B 1/2W
DIODE
1SS133T-77
DIODE
1SS133T-77
DIODE
1SS133T-77
WIRE , COPPER
SN95/PB5 , 0.6
COIL , AXAIL (10UH)
TRANSISTOR , KTC1027Y
KTC1027Y/TO-92L/KEC
TRANSISTOR , TO-92M
KRA107M
TRANSISTOR , TO-92M
KRC107M
TRANSISTOR , TO-92M
KRC107M
TRANSISTOR KTA1271Y
TRANSISTOR , TO-92M
KRC107M
TRANSISTOR , TO-92M
KRC107M
TRANSISTOR , TO-92M
KRA107M
TRANSISTOR , TO-92M
KRA107M
TRANSISTOR , MUTE
KTC2874B
TRANSISTOR , MUTE
KTC2874B
TRANSISTOR , MUTE
KTC2874B
TRANSISTOR , MUTE
KTC2874B
TRANSISTOR , TO-92M
KRC107M
TRANSISTOR , TO-92M
KRA107M
TRANSISTOR , TO-92M
KRC107M
RES , CARBON(220 OHM, 1%)
RES , CARBON(680 OHM, 1%)
RES, CARBON(1/5W,330Kohm,J)
RES, CARBON(1/5W,100ohm,J)
RES, CARBON(1/5W,2.7Kohm,J)
RES , CARBON
1K /1/5W /F
RES , CARBON
1.5K /1/5W /F
RES , CARBON
1.8K /1/5W /F
RES , CARBON
2.7K /1/5W/F
RES , CARBON
3.3K /1/5W/F
RES , CARBON
1K /1/5W /F
RES , CARBON
1.5K /1/5W /F
RES , CARBON
1.8K /1/5W /F
RES , CARBON
2.7K /1/5W/F
48
AVR 2650
Reference
Designator
harman/kardon
Part Number
FRONT PCB ASS'Y

R326
R327
R328
R401
R402
R403
R404
R411
R412
R413
R415
R431
R432
R550
R555
R556
R557
R701
R702
R703
R711
R712
R713
R721
R722
R731
R735
R741
R742
R801
R802
R811
R812
R813
R821
R822
R823
R834
R835
R836
R901
R902
R911
R912
R921
R922
R923
R924
R925
R926
R931
R932
R933
CRD20TF3301T
CRD20TF5601T
CRD20TF5601T
CRD25FJ3R3T
CRD25TJ4R7T
CRD20TJ100T
CRD25TJ4R7T
CRD20TJ104T
CRD20TJ122T
CRD20TJ104T
CRD20TJ473T
CRD20TJ100T
CRD20TJ100T
CRD20TJ100T
CRD20TJ100T
CRD20TJ153T
CRD20TJ153T
CRD20TJ102T
CRD20TJ102T
CRD20TJ102T
CRD20TJ470T
CRD20TJ470T
CRD20TJ470T
CRD20TJ103T
CRD20TJ101T
CRD20TJ100T
CRD20TJ152T
CRD20TJ123T
CRD20TJ102T
CRD20TJ101T
CRD20TJ101T
CRD20TJ104T
CRD20TJ102T
CRD20TJ103T
CRD20TJ102T
CRD20TJ103T
CRD20TJ104T
CRD20TJ222T
CRD20TJ103T
CRD20TJ152T
CRD25TJ101T
CRD20TJ101T
CRD20TJ101T
CRD20TJ101T
CRD20TJ102T
CRD20TJ102T
CRD20TJ152T
CRD20TJ152T
CRD20TJ104T
CRD20TJ104T
CRD20TJ104T
CRD20TJ104T
CRD20TJ221T
Description
CIP12357D
RES , CARBON
3.3K /1/5W/F
RES , CARBON(5.6K/F)
RES , CARBON(5.6K/F)
RES , CARBON
3.3 OHM 1/4W J
RES, CARBON(1/4W,4.7ohm,J)
RES, CARBON(1/4W,4.7ohm,J)
49
AVR 2650
Reference
Designator
harman/kardon
Part Number
FRONT PCB ASS'Y

R934
R935
R936
R941
R942
R943
R944
R951
R953
R954
S311
S312
S313
S314
S315
S316
S317
S318
S319
S320
S321
S322
S323
S330
BK71
BK72
BK73
BN53
BN61
BN73
BN74
CN61
CN71
CN72
CN73
CN74
C411
D101
D102
D201
D202
D203
ET63
FIP2
IC12
IC13
IC14
IC15
JK53
JK63
RL91
VR74
Description
CIP12357D
CRD20TJ221T
CRD20TJ221T
CRD20TJ221T
CRD25TJ432T
CRD20TJ472T
CRD20TJ472T
CRD20TJ472T
CRD20TJ102T
CRD20TJ362T
CRD20TJ103T
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CST1A024ZT
SW , TACT
CMD1A572
BRACKET , FIP
CMD1A572
BRACKET , FIP
CMD1A629
BRACKET , PCB
CWB1C005350BM001
Shield Wire ass'y
CJP06GB142ZB
PIN HEADER(6P, 2.54mm)
CJP06GB142ZB
PIN HEADER(6P, 2.54mm)
CWB1C005100BM
WIRE ASS'Y(5P, 100MM)
CJP06GA221ZB
FEMALE HEADER (6P,2.54mm)STRAIGHT TYPE FAS2851
CJP05GB03ZY
WAFER,YMAW025(2.5mm,ANGLE)
CJP27GA285ZN
WAFER,FPC 1.25mm,stright
1.25-2-NP
CJP06GB143ZB
FEMALE HEADER(6P, 2.54mm)
CJP05GB03ZY
WAFER,YMAW025(2.5mm,ANGLE)
CCEA1JH101E
CAP , ELECT
100UF 63V
CVD1L0345W31BOCT201V L.E.D , WHITE
CVD1L0345W31BOCT201
CVD30ASOGCAA-S7
L.E.D , ORANGE
T0L-30ASOGCAA-S7
CVD1L0345W31BOCT201
CVD1L0345W31BOCT201
CVD1L0345W31BOCT201
CMC2A325
PLATE , EARTH
CFL162BD01GINK
V.F.D
162-BD-01GINK
CRVKSM603TE5B
SENSOR , REMOCON
CVISN74ACT04DR
I.C , HEX INVERTERS(SOIC/D-14P)SN74ACT04DR TEXAS
HVINJM2068MDTE1
I.C , OP AMP (JRC)
NJM2068MD-TE1
HVINJM4556AL
I.C , HEADPHONE (JRC) NJM4556AL
CJJ9X009Z
JACK, USB
CJJ2E026Z
JACK, PHONES(6.35mm,SILVER) PJ-612A-51/YUQIU
CSL4A016ZU
RELAY,BC3-12H,DC12V,2C2P
BC3-12H/HANDOUK
CSR2A037Z
ENCODER
CPE1A009
SHEET , BLIND
50
AVR 2650
Reference
Designator
harman/kardon
Part Number
Description
FRONT PCB ASS'Y
CN72
CTB3+10JR
CTWS3+10GR
CWC4C4A27B250B08
CGX1A338MBC63
CGX4A390C66Z
CKC6B145S60
CMH1A214
CMZ2A090
CTB3+8JFZR
CTB4+6FFZR
CUAAVR2650
CFNRDM6025S
CHD1A012ZR
CHD1A023R
CHD1A036FZR
CHD1A065R
CHD4A012R
CHE170
CHE36-3
CHG1A113
CHG1A160Z
CHG1A373
CHR301
CKF3A444Z
CKL1A094
CKL1A095
CMD1A506
CMD1A702
CMD1A786
CNVFS2026-020021
INPUT PCB ASS'Y

C133
C134
C135
C136
C217
C218
C219
C293
C300
C301
C302
C303
C304
C305
C306
C307
C332
C333
C334
C335
CIP12357D
SCREW
27.0
SCREW
2.0
CARD , CABLE (27P/1.25mm,/250mm)
CAP , VOLUME
SHEET , AL FRONT AVR2650
CABINET , TOP
HOLDER , VOLUME
SHEET , VOLUME
SCREW
17.0
SCREW
6.0
BOTTOM CHASSIS ASS'Y
MOTOR , FAN (60X60X25) 12V, 0.1A
SCREW , SPECIAL
2.0
SCREW , SPECIAL
4.0
SCREW , SPECIAL
2.0
SCREW , FLAT(2.6X4)
2.0
SCREW , SPECIAL
4.0
HOLDER , PCB
2.0
CLAMPER , WIRE
RUBBER
3.0
CUSHION , RUBBER
CUSHION , FOOT
4.0
CLAMPER
2.0
PANEL , REAR AVR2650
FOOT , A
2.0
FOOT , B
2.0
BRACKET , FAN
FRAME , BOTTOM
BRACKET , HDMI
MODULE,VENICE6.2 (NO DAB, NO WIFI)
COP12327D
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H101JA
CCUS1H101JA
CCUS1H101JA
CCUS1H104KC
CCUS1H272KC
CCUS1H272KC
CCUS1H683KC
CCUS1H272KC
CCUS1H272KC
CCUS1H272KC
CCUS1H272KC
CCUS1H272KC
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CAP,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
CHIP(1608,
51
50V/0.1uF)
50V/0.1uF)
50V/0.1uF)
50V/0.1uF)
50V/100pF)
50V/100pF)
50V/100pF)
50V/0.1uF)
50V/2700pF)
50V/2700pF)
50V/0.068uF)
50V/2700pF)
50V/2700pF)
50V/2700pF)
50V/2700pF)
50V/2700pF)
50V/0.01uF)
50V/0.01uF)
50V/0.01uF)
50V/0.01uF)
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C336
C337
C338
C339
C356
C357
C362
C369
C370
C371
C372
C373
C375
C376
C377
C412
C413
C420
C421
C422
C423
C466
C601
C603
C605
C607
C609
C611
C613
C615
C617
C619
C621
C623
C625
C627
C629
C631
C641
C643
C644
C645
C646
C648
C651
C652
C653
C654
C655
C656
C658
C660
C704
Description
COP12327D
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUS1H104KC
CCUS1H104KC
CCUS1H223KC
CCUS1H223KC
CCUS1H223KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H151JA
CCUS1H151JA
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCSNA0J220B
CCUS1H104KC
CAP, CHIP(1608, 50V/0.01uF)

CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/150pF)
CAP, CHIP(1608, 50V/150pF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , CHIP TANTAL(22uF/6.3V, NingXia XingRi)
CAP, CHIP(1608, 50V/0.1uF)
52
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C705
C714
C718
C719
C722
C723
C727
C729
C731
C733
C737
C738
C739
C741
C745
C746
C747
C748
C751
C754
C756
C757
C758
C759
C760
C761
C762
C763
C765
C773
C780
C781
C788
C789
C792
C865
L101
L604
L704
RN89
R118
R122
R123
R124
R125
R126
R163
R165
R171
R217
R218
R219
R289
Description
COP12327D
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCSNA0J220B
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H102KC
CCUS1H223KC
CCUS1H104KC
CCUS1H103KC
CCUS1H104KC
CCUS1H104KC
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CRJ104DJ103T
CRJ10DJ104T
CRJ10DJ473T
CRJ10DJ473T
CRJ10DJ473T
CRJ10DJ473T
CRJ10DJ332T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ0R0T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ104T
CAP, CHIP(1608, 50V/0.1uF)

CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/1000pF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
FERRITE CHIP BEAD(1608/60ohm)HCB1608KF-600T30/COILMASTER
RES , CHIP , 10K OHM, 5% , 1608 X 4
10K(1608)
RES, CHIP(1608/5%/100Kohm)
RES, CHIP(1608/5%/3.3Kohm)
RES, CHIP(1608/5%/0ohm)
53
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

R290
R291
R292
R293
R294
R317
R320
R321
R322
R323
R324
R325
R326
R327
R339
R341
R380
R381
R382
R383
R384
R389
R390
R399
R400
R401
R402
R403
R404
R406
R407
R424
R425
R448
R460
R465
R466
R471
R700
R713
R717
R718
R719
R720
R721
R725
R726
R727
R733
R735
R745
R753
R754
Description
COP12327D
CRJ10DJ104T
CRJ10DJ563T
CRJ10DJ563T
CRJ10DJ563T
CRJ10DJ563T
CRJ10DJ561T
CRJ10DJ682T
CRJ10DJ682T
CRJ10DJ103T
CRJ10DJ682T
CRJ10DJ682T
CRJ10DJ682T
CRJ10DJ682T
CRJ10DJ682T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ561T
CRJ10DJ561T
CRJ10DJ561T
CRJ10DJ561T
CRJ10DJ563T
CRJ10DJ563T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ182T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ472T
CRJ10DJ392T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ472T
CRJ10DJ472T
CRJ10DJ101T
CRJ10DJ103T
CRJ10DJ103T
CRJ10DJ0R0T
CRJ10DF1371T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ472T
CRJ10DJ0R0T
CRJ10DJ100T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ103T
CRJ10DJ103T
CRJ10DJ332T
CRJ10DJ332T
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/56Kohm)
CHIP(1608/5%/560ohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/560ohm)
CHIP(1608/5%/560ohm)
CHIP(1608/5%/560ohm)
CHIP(1608/5%/560ohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/1.8Kohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/3.9Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/1%/1.37Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/10ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
54
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

R759
R761
R762
R763
R767
R785
R788
R795
R797
R812
R834
R835
R836
R837
R857
R858
R863
R866
R870
R871
R872
R877
R891
R907
R908
R910
R925
R932
R963
R966
R968
R969
C111
C112
C113
C114
C115
C116
C117
C118
C121
C123
C131
C132
C203
C204
C205
C206
C207
C208
C209
C210
C227
Description
COP12327D
CRJ10DJ0R0T
CRJ10DJ102T
CRJ10DJ102T
CRJ10DJ103T
CRJ10DF5101T
CRJ10DJ104T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ103T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ103T
CRJ10DJ0R0T
CRJ10DJ473T
CRJ10DJ473T
CRJ10DJ473T
CRJ10DJ472T
CRJ10DJ0R0T
CRJ10DJ103T
CRJ10DJ105T
CRJ10DJ105T
CRJ10DJ0R0T
CRJ10DJ103T
CRJ10DJ105T
CRJ10DJ472T
CRJ10DJ105T
CRJ10DJ103T
CCUI1C104KC
CCUI1C104KC
CCUS1H180JA
CCUS1H180JA
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUS1H104KC
CRJ06IJ183T
CCUS1H150JA
CCUS1H150JA
CCUS1H221JA
CCUS1H221JA
CCUS1H221JA
CCUS1H221JA
CCUS1H221JA
CCUS1H221JA
CCUS1H221JA
CCUS1H221JA
CCUS1H104KC
RES, CHIP(1608/5%/1Mohm)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/18pF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/0.1uF)
55
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C228
C229
C230
C260
C277
C278
C291
C308
C309
C310
C311
C312
C313
C314
C315
C316
C317
C318
C319
C320
C321
C322
C323
C324
C325
C326
C327
C328
C329
C330
C331
C358
C359
C363
C364
C365
C383
C384
C385
C386
C387
C388
C394
C428
C442
C455
C456
C457
C458
C459
C460
C461
C462
Description
COP12327D
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H391JA
CCUS1H391JA
CCUS1H822KC
CCUS1H391JA
CCUS1H391JA
CCUS1H391JA
CCUS1H391JA
CCUS1H391JA
CCUS1H272KC
CCUS1H272KC
CCUS1H683KC
CCUS1H272KC
CCUS1H272KC
CCUS1H272KC
CCUS1H272KC
CCUS1H272KC
CCUS1H391JA
CCUS1H391JA
CCUS1H822KC
CCUS1H391JA
CCUS1H391JA
CCUS1H391JA
CCUS1H391JA
CCUS1H391JA
CCUS1H392KC
CCUS1H822KC
CCUI1E103KC
CCUS1H392KC
CCUS1H822KC
CCUS1H223KC
CCUS1H223KC
CCUS1H223KC
CCUS1H223KC
CCUS1H223KC
CCUS1H223KC
CCUS1H102KC
CCUI1H151JA
CCUI1H151JA
CCUI1H101JA
CCUI1H151JA
CCUI1H101JA
CCUI1H151JA
CCUI1C104KC
CCUS1H272KC
CCUS1H272KC
CCUI1C104KC
CAP, CHIP(1608, 50V/0.1uF)

CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/8200pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/2700pF)
CAP, CHIP(1608, 50V/2700pF)
CAP, CHIP(1608, 50V/0.068uF)
CAP, CHIP(1608, 50V/2700pF)
CAP, CHIP(1608, 50V/2700pF)
CAP, CHIP(1608, 50V/2700pF)
CAP, CHIP(1608, 50V/2700pF)
CAP, CHIP(1608, 50V/2700pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/8200pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/390pF)
CAP, CHIP(1608, 50V/3900pF)
CAP, CHIP(1608, 50V/8200pF)
CAP, CHIP(1005, 25V/0.01uF)
CAP, CHIP(1608, 50V/3900pF)
CAP, CHIP(1608, 50V/8200pF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/1000pF)
CAP, CHIP(1005, 50V/150pF)
CAP, CHIP(1005, 50V/150pF)
CAP, CHIP(1005, 50V/100pF)
CAP, CHIP(1005, 50V/150pF)
CAP, CHIP(1005, 50V/100pF)
CAP, CHIP(1005, 50V/150pF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/2700pF)
CAP, CHIP(1608, 50V/2700pF)
CAP , CHIP (1005, 16V/0.1uF)
56
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C610
C642
C647
C649
C650
C657
C659
C701
C702
C707
C708
C725
C734
C742
C743
C744
C767
C768
C769
C770
C772
C776
C778
C790
C791
C794
C795
C797
C798
C801
C802
C820
C830
C831
C832
C833
C834
C835
C836
C837
C838
C839
C840
C841
C842
C843
C846
C860
C864
C866
C867
D201
D202
Description
COP12327D
CCUI1H150JA
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUI1C104KC
CCUS1H104KC
CCUS1H150JA
CCUS1H150JA
CCUI1H102KC
CCUI1C104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H300JA
CCUI1C104KC
CCUS1H330JA
CCUS1A105KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUI1H150JA
CCUS1H104KC
CCUS1H103KC
CCUS1H104KC
CCUI1H181JA
CCUI1H181JA
CCUI1C104KC
CCUI1C104KC
CCUS1H180JA
CCUS1H180JA
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUI1H101JA
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H180JA
CCUS1H150JA
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H330JA
CCUS1H103KC
CVD1SS355T
CVD1SS355T

CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1005, 50V/1000pF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 10V/1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1005, 50V/180pF)
CAP, CHIP(1005, 50V/180pF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1005, 50V/100pF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.01uF)
DIODE, SMD, SWITCHING 1SS355/SOD-323
57
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y
Description
COP12327D
D203
D204
D205
D206
D301
D302
D726
D805
D806
IC101
IC104
IC105
IC106
IC106
IC107
IC107
IC111
IC112
IC113
IC114
IC122
IC125
IC131
IC132
IC140
IC141
IC142
IC143
IC144
IC145
IC146
IC147
IC148
IC149
IC150
IC151
IC151
IC152
IC154
IC154
IC155
IC156
IC158
IC159
IC161
IC162
IC162
CVD1SS355T
CVD1SS355T
CVD1SS355T
CVD1SS355T
CVD1SS355T
CVD1SS355T
HVDRB160L60TE25
CVD1SS355T
CVD1SS355T
CVIR2A15218FP
HVINJM2115MDTE1
HVINJM2115MDTE1
CVIANAM1620AV
CVIST25VF080B504CS2F
CVIANAM1621AV
CVIST25VF080B504CS2F
CVIAZ4580MTR-E1
CVIAZ4580MTR-E1
CVIAZ4580MTR-E1
CVIAZ4580MTR-E1
CVIAZ4580MTR-E1
CVIAZ4580MTR-E1
CVIBD3812F
CVIAZ4580MTR-E1
CVITC74HC151AFN
CVICS497024CVZ
CVICS49DV8CCVZ
HVICS42528-CQ
CVIM12L16161A5TG
HVITC74VHC157FT
CVITC74VCX541FT
CVITC74VHC153FT
HVINJM2391DL133
HVILM1117S-1V8
HVILM1117S-1V8
CVIANAM1548AV
CVIT5CN5
CVIM24C32WMN6TP
CVIANAM1619AV
CVITMPM330FWFG
CVTUPA672T
CVIKIC3201S-33
HVILM1117S-3V3
HVI74HCU04AFNG
CVIKSZ8851SNLTR
CVIANAM1549AV
CVITMP92FD28FG

DIODE , SCHOTTKEY BARRIER
HK RB160L-60TE25
I.C , INPUT WITH 8CH VOLUME(100P QFP) R2A15218FP
IC, OP AMP
NJM2115MDTE1
IC, OP AMP
NJM2115MDTE1
I.C , DSP-ROM1(AVR265/365 , ST25VF080B504CS2F)
I.C , 8 Mbit SPI Serial Flash SST25VF080B-50-4C-S2AF
I.C , DSP-ROM2(AVR265/365 , ST25VF080B504CS2F)
I.C , 8 Mbit SPI Serial FlashSST25VF080B-50-4C-S2AF
I.C , OPAMP(DUAL LOW NOISE) AZ4580MTR-E1/SOIC8/BCD
I.C , VIDEO 2CH BD3812F
I.C , 8 CHAN MULTIPLEXER(SOL16-P-150-1.27)TC74HC151AFN
I.C , DSP (CIRRUS LOGIC) CS497024CVZ
I.C , DSP (DOLBY VOLUME) CIRRUS LOGIC CS49DV8CCVZ
I.C , CODEC + DIR (CIRRUS LOGIC) CS42528-CQ
I.C , 16MB SDRAM (ESMT) M12L16161A5TG
I.C , 2-CHANNEL MUX (TOSHIBA) TC74VHC157FT
I,C , OCTAL BUS BUFFER (TOSHIBA) TC74VCX541FT
I.C DUAL 4-CH MUX TC74VHC153FT TC74VHC153FT
I.C , CHIP REGULATOR (+3.3V) JRC NJM2391DL133
I.C , REGULATOR (1.8V) LM1117-1V8
I.C , REGULATOR (1.8V) LM1117-1V8
I,C , U-COM CVIT5CN5,
I.C , U-COM (512KB/32KB, LQFP100P) TOSHIBA
I.C , EEPROM (32 Kbit) ST M24C32WMN6TP
I.C , SUB U-COM(AVR265/365 , TMPM330FWFG)
I.C , U-COM (TOSHIBA,128KB/8KB,LQFP-100P)TMPM330FWFG
F.E.T (NEC) UPA672T
I.C , REGULATOR (3V3)
KIC3201S-33(SOT-89)
I.C , REGULATOR (3.3V)
1117S-3.3V
I.C , INVERTER (TOSHIBA) TC74HCU04AFNG(TOSHIBA)
I.C , ETHERNET PHY (10/100M,QFN-32P KSZ8851SNLTR
IC, USB U-COM(CVITMP92FD28FG,
I.C , USB DECODER FLASH(100PIN, QFP)
TOSHIBA TMP92FD28DFG, FLASH
I.C , RESET (2.8V , SOT-89) ML61C282PRG
I.C , REGULATOR (ADJ, DPAK-5) KIA78R000F
IC , CURRENT LIMITER RT9702APB
FERRITE, CHIP BEAD(60ohm, 2012) HCB2012KF-600T40
58
IC164
IC167
IC168
L601
L602
CVIML61C282PR
CVIKIA78R000F
CVIRT9702APB
CLZ9R001Z
CLZ9R001Z
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

L701
L702
L703
L705
L706
L715
L802
L803
L804
L805
L806
L807
Q101
Q102
Q103
Q105
Q301
Q302
Q303
Q304
Q305
Q306
Q307
Q308
Q402
Q729
Q730
Q732
Q734
Q738
Q741
Q742
Q951
Q952
Q991
Q992
Q993
Q994
Q997
Q998
RN53
RN54
RN60
RN61
RN63
RN64
RN65
RN66
RN67
RN68
RN71
RN76
RN77
Description
COP12327D
CLZ9Z014Z
CLZ9Z014Z
CLZ9Z014Z
CLZ9R005Z
CLZ9Z014Z
CLZ9R001Z
CLZ9R001Z
CLZ9R001Z
CLZ9R001Z
CLZ9R001Z
CLZ9R001Z
CLZ9R001Z
HVTKRA107S
HVTKRA107S
HVTKRA107S
HVTKRA107S
HVTKTC812TB
HVTKTC812TB
HVTKTC812TB
HVTKTC812TB
HVTKTC812TB
HVTKTC812TB
HVTKRA107S
HVTKRA107S
HVTKTC812TB
HVTKRC107S
HVTKRC107S
HVTKRC107S
HVTKRC107S
CVTKRC103S
HVTKRC107S
HVTKRA107S
HVTKRC107S
HVTKRA107S
HVTKRC107S
HVTKRA107S
HVTKRA107S
HVTKRC107S
HVTKRA107S
HVTKRC107S
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ104DJ103T
CRJ104DJ103T
CRJ064IJ101T
CRJ064IJ101T
CRJ064IJ101T
CRJ064IJ101T
CRJ104DJ103T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
FERRITE, CHIP BEAD(60ohm, 4516) HCB4516KF-600T60/COILMASTER

FERRITECHIP BEAD(1608/60ohm)
HCB1608KF-600T30/COILMASTER
TRANSISTOR , CHIP , SOT-23 KRA107S
TRANSISTOR , CHIP(TS6)
KTC812T-B-RTK
KTC812T-B-RTK
KTC812T-B-RTK
KTC812T-B-RTK
KTC812T-B-RTK
KTC812T-B-RTK
KTC812T-B-RTK
TRANSISTOR , CHIP , SOT-23 KRC107S
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES , CHIP , 10K OHM, 5% , 1608 X 4
RES , CHIP , 10K OHM, 5% , 1608 X 4
RES, CHIP(1005/5%/100ohm*4)
RES, CHIP(1005/5%/100ohm*4)
RES, CHIP(1005/5%/100ohm*4)
RES, CHIP(1005/5%/100ohm*4)
RES , CHIP , 10K OHM, 5% , 1608 X 4
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
59
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

RN78
RN79
RN81
RN82
RN83
RN84
RN85
RN87
RN90
RN91
RN93
R110
R111
R112
R113
R114
R115
R116
R117
R121
R141
R142
R149
R150
R151
R152
R156
R158
R161
R162
R166
R167
R172
R173
R174
R201
R202
R203
R204
R205
R206
R207
R208
R209
R210
R229
R230
R231
R232
R233
R234
R235
R236
Description
COP12327D
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ06IJ103T
CRJ06IJ103T
CRJ06IJ330T
CRJ06IJ472T
CRJ06IJ472T
CRJ06IJ103T
CRJ10DJ105T
CRJ10DJ104T
CRJ06IJ0R0T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ101T
CRJ06IJ330T
CRJ10DJ104T
CRJ10DJ102T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ103T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1005/5%/33ohm)
CHIP(1005/5%/4.7Kohm)
CHIP(1005/5%/4.7Kohm)
CHIP(1608/5%/1Mohm)
CHIP(1608/5%/100Kohm)
CHIP(1005/5%/0ohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100ohm)
CHIP(1005/5%/33ohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/1Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
60
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

R237
R238
R239
R240
R241
R242
R243
R247
R248
R249
R250
R258
R259
R260
R263
R264
R265
R266
R267
R268
R274
R281
R282
R283
R284
R285
R286
R287
R288
R295
R296
R297
R298
R300
R301
R302
R303
R304
R305
R306
R307
R308
R309
R310
R311
R312
R313
R314
R315
R316
R319
R328
R329
Description
COP12327D
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ4R7T
CRJ10DJ4R7T
CRJ10DJ4R7T
CRJ10DJ184T
CRJ10DJ184T
CRJ10DJ184T
CRJ10DJ184T
CRJ10DJ184T
CRJ10DJ184T
CRJ10DJ222T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ152T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ563T
CRJ10DJ563T
CRJ10DJ563T
CRJ10DJ563T
CRJ10DJ103T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ561T
CRJ10DJ152T
CRJ10DJ152T
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/4.7ohm)
CHIP(1608/5%/4.7ohm)
CHIP(1608/5%/4.7ohm)
CHIP(1608/5%/180Kohm)
CHIP(1608/5%/180Kohm)
CHIP(1608/5%/180Kohm)
CHIP(1608/5%/180Kohm)
CHIP(1608/5%/180Kohm)
CHIP(1608/5%/180Kohm)
CHIP(1608/5%/2.2Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/560ohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
61
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

R330
R331
R332
R333
R334
R335
R336
R337
R338
R340
R342
R343
R344
R345
R346
R347
R348
R349
R350
R351
R352
R353
R354
R355
R356
R357
R358
R359
R360
R361
R362
R363
R364
R365
R366
R367
R368
R369
R370
R371
R372
R373
R374
R375
R376
R377
R378
R379
R385
R386
R387
R388
R391
Description
COP12327D
CRJ10DJ152T
CRJ10DJ152T
CRJ10DJ152T
CRJ10DJ152T
CRJ10DJ152T
CRJ10DJ152T
CRJ10DJ682T
CRJ10DJ104T
CRJ10DJ102T
CRJ10DJ561T
CRJ10DJ392T
CRJ10DJ392T
CRJ10DJ682T
CRJ10DJ682T
CRJ10DJ682T
CRJ10DJ682T
CRJ10DJ682T
CRJ10DJ682T
CRJ10DJ472T
CRJ10DJ472T
CRJ10DJ152T
CRJ10DJ152T
CRJ10DJ301T
CRJ10DJ273T
CRJ10DJ152T
CRJ10DJ152T
CRJ10DJ152T
CRJ10DJ152T
CRJ10DJ152T
CRJ10DJ152T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ301T
CRJ10DJ273T
CRJ10DJ0R0T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ561T
CRJ10DJ561T
CRJ10DJ561T
CRJ10DJ561T
CRJ10DJ392T
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/1Kohm)
CHIP(1608/5%/560ohm)
CHIP(1608/5%/3.9Kohm)
CHIP(1608/5%/3.9Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/6.8Kohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/300ohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/1.5Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/300ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/560ohm)
CHIP(1608/5%/560ohm)
CHIP(1608/5%/560ohm)
CHIP(1608/5%/560ohm)
CHIP(1608/5%/3.9Kohm)
62
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

R392
R393
R395
R396
R397
R398
R408
R410
R411
R412
R413
R414
R415
R416
R417
R418
R419
R420
R421
R422
R423
R452
R454
R455
R456
R461
R462
R463
R464
R472
R473
R474
R601
R602
R603
R604
R605
R606
R607
R610
R611
R612
R613
R614
R615
R616
R619
R620
R621
R622
R701
R702
R706
Description
COP12327D
CRJ10DJ392T
CRJ10DJ392T
CRJ10DJ392T
CRJ10DJ392T
CRJ10DJ392T
CRJ10DJ392T
CRJ10DJ105T
CRJ10DJ0R0T
CRJ10DJ272T
CRJ10DJ0R0T
CRJ10DJ272T
CRJ10DJ472T
CRJ10DJ472T
CRJ10DJ272T
CRJ10DJ472T
CRJ10DJ472T
CRJ10DJ272T
CRJ06IJ101T
CRJ06IJ101T
CRJ06IJ101T
CRJ06IJ101T
CRJ06IJ563T
CRJ10DJ562T
CRJ10DJ122T
CRJ10DJ562T
CRJ10DJ104T
CRJ10DJ104T
CRJ06IJ561T
CRJ06IJ561T
CRJ10DJ101T
CRJ06IJ563T
CRJ10DJ122T
CRJ06IJ101T
CRJ10DJ103T
CRJ10DJ103T
CRJ10DJ103T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ0R0T
CRJ10DF5101T
CRJ10DJ103T
CRJ06IJ820T
CRJ06IJ330T
CRJ06IJ330T
CRJ10DJ332T
CRJ10DJ0R0T
CRJ10DJ103T
CRJ06IJ750T
CRJ10DJ332T
CRJ10DJ332T
CRJ10DJ103T
CRJ10DJ103T
CRJ10DJ221T
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
CHIP(1608/5%/3.9Kohm)
CHIP(1608/5%/3.9Kohm)
CHIP(1608/5%/3.9Kohm)
CHIP(1608/5%/3.9Kohm)
CHIP(1608/5%/3.9Kohm)
CHIP(1608/5%/3.9Kohm)
CHIP(1608/5%/1Mohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/2.7Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/2.7Kohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/2.7Kohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/2.7Kohm)
CHIP(1005/5%/100ohm)
CHIP(1005/5%/100ohm)
CHIP(1005/5%/100ohm)
CHIP(1005/5%/100ohm)
CHIP(1608/5%/5.6Kohm)
CHIP(1608/5%/1.2Kohm)
CHIP(1608/5%/5.6Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1005/5%/560ohm)
CHIP(1005/5%/560ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/1.2Kohm)
CHIP(1005/5%/100ohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/1%/5.1Kohm)
CHIP(1005/5%/82ohm)
CHIP(1005/5%/33ohm)
CHIP(1005/5%/33ohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/0ohm)
CHIP(1005/5%/75ohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/220ohm)
63
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

R707
R709
R710
R711
R712
R714
R715
R722
R723
R724
R728
R729
R730
R732
R734
R737
R739
R741
R742
R743
R746
R748
R749
R750
R751
R752
R755
R756
R757
R760
R764
R765
R766
R768
R769
R773
R774
R775
R776
R777
R778
R782
R783
R784
R786
R787
R789
R790
R791
R792
R798
R799
R800
Description
COP12327D
CRJ10DJ221T
CRJ10DJ103T
CRJ10DJ103T
CRJ06IJ560T
CRJ06IJ820T
CRJ10DJ103T
CRJ10DJ103T
CRJ06IJ0R0T
CRJ06IJ330T
CRJ06IJ101T
CRJ06IJ102T
CRJ06IJ330T
CRJ06IJ330T
CRJ10DJ103T
CRJ10DJ332T
CRJ06IJ330T
CRJ06IJ820T
CRJ06IJ330T
CRJ06IJ330T
CRJ06IJ330T
CRJ10DJ103T
CRJ10DJ0R0T
CRJ06IJ750T
CRJ10DJ103T
CRJ06IJ820T
CRJ06IJ330T
CRJ10DJ103T
CRJ06IJ750T
CRJ06IJ750T
CRJ10DJ105T
CRJ06IJ330T
CRJ06IJ330T
CRJ10DJ0R0T
CRJ06IJ330T
CRJ06IJ330T
CRJ10DJ332T
CRJ10DJ103T
CRJ10DJ332T
CRJ10DJ332T
CRJ06IJ101T
CRJ06IJ221T
CRJ10DJ272T
CRJ10DJ272T
CRJ10DJ473T
CRJ10DJ471T
CRJ06IJ0R0T
CRJ10DJ103T
CRJ10DJ103T
CRJ10DJ273T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ332T
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
CHIP(1608/5%/220ohm)
CHIP(1005/5%/56ohm)
CHIP(1005/5%/82ohm)
CHIP(1005/5%/0ohm)
CHIP(1005/5%/33ohm)
CHIP(1005/5%/100ohm)
CHIP(1005/5%/1Kohm)
CHIP(1005/5%/33ohm)
CHIP(1005/5%/33ohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1005/5%/33ohm)
CHIP(1005/5%/82ohm)
CHIP(1005/5%/33ohm)
CHIP(1005/5%/33ohm)
CHIP(1005/5%/33ohm)
CHIP(1608/5%/0ohm)
CHIP(1005/5%/75ohm)
CHIP(1005/5%/82ohm)
CHIP(1005/5%/33ohm)
CHIP(1005/5%/75ohm)
CHIP(1005/5%/75ohm)
CHIP(1608/5%/1Mohm)
CHIP(1005/5%/33ohm)
CHIP(1005/5%/33ohm)
CHIP(1608/5%/0ohm)
CHIP(1005/5%/33ohm)
CHIP(1005/5%/33ohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1608/5%/3.3Kohm)
CHIP(1005/5%/100ohm)
CHIP(1005/5%/220ohm)
CHIP(1608/5%/2.7Kohm)
CHIP(1608/5%/2.7Kohm)
CHIP(1608/5%/470ohm)
CHIP(1005/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/3.3Kohm)
64
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

R801
R802
R803
R806
R807
R810
R811
R815
R816
R820
R821
R822
R823
R824
R825
R826
R827
R828
R832
R833
R838
R839
R840
R841
R842
R843
R848
R849
R852
R853
R854
R855
R856
R860
R861
R862
R864
R869
R880
R890
R909
R921
R923
R960
R967
R992
WF104
WF105
C137
C138
C231
C232
C233
Description
COP12327D
CRJ10DJ332T
CRJ06IJ105T
CRJ10DJ330T
CRJ10DJ474T
CRJ10DJ474T
CRJ10DJ103T
CRJ06IJ103T
CRJ06IJ330T
CRJ06IJ330T
CRJ06IJ330T
CRJ06IJ330T
CRJ06IJ330T
CRJ06IJ330T
CRJ10DJ472T
CRJ10DJ472T
CRJ06IJ330T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ330T
CRJ10DJ330T
CRJ10DF49R9T
CRJ10DF49R9T
CRJ10DF49R9T
CRJ10DF49R9T
CRJ10DJ223T
CRJ10DJ473T
CRJ10DJ100T
CRJ10DJ100T
CRJ10DJ4R7T
CRJ10DJ104T
CRJ10DJ103T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ272T
CRJ10DJ100T
CRJ10DJ301T
CRJ10DJ473T
CRJ06IJ0R0T
CRJ10DJ100T
CRJ10DJ0R0T
CRJ10DJ153T
CRJ10DJ103T
CRJ10DJ103T
CRJ10DJ332T
CRJ10DJ153T
CRJ10DJ153T
CJP17GA193ZY
CJP17GA193ZY
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
RES, CHIP(1608/1%/49.9ohm)
RES, CHIP(1608/1%/49.9ohm)
RES, CHIP(1608/1%/49.9ohm)
RES, CHIP(1608/1%/49.9ohm)
RES, CHIP(1608/5%/4.7ohm)
WAFER, CARD CABLE (SMD)
WAFER, CARD CABLE (SMD)
65
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C234
C235
C236
C237
C238
C281
C282
C283
C284
C285
C286
C287
C288
C292
C294
C295
C296
C297
C298
C340
C341
C342
C343
C344
C345
C346
C347
C361
C374
C389
C390
C414
C415
C429
C430
C441
C452
C453
C454
C463
C464
C465
C612
C614
C628
C630
C703
C706
C717
C720
C721
C726
C728
Description
COP12327D
CCEA1CH101T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1HH220T
CCEA1HH220T
CCEA1HH220T
CCEA1HH220T
CCEA1HH220T
CCEA1HH220T
CCEA1HH220T
CCEA1HH220T
CCEA1CH101T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1EH101T
CCEA1HH100T
CCEA1HH100T
CCEA1EH101T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1CH101T
CCEA1CKS101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1HH4R7T
CCEA1CH101T
CCEA1AH471T
CCEA1CH101T
CCEA1AH471T
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
ELECT(16V/100uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(16V/100uF)
ELECT(16V/100uF)
ELECT(16V/100uF)
ELECT(16V/100uF)
ELECT(16V/100uF)
ELECT(16V/100uF)
ELECT(50V/22uF)
ELECT(50V/22uF)
ELECT(50V/22uF)
ELECT(50V/22uF)
ELECT(50V/22uF)
ELECT(50V/22uF)
ELECT(50V/22uF)
ELECT(50V/22uF)
ELECT(16V/100uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(25V/100uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(25V/100uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(50V/10uF)
ELECT(16V/100uF)
ELECT(16V/100uF)-S
ELECT(16V/100uF)
ELECT(16V/100uF)
ELECT(16V/100uF)
ELECT(16V/100uF)
ELECT(50V/4.7uF)
ELECT(16V/100uF)
ELECT(10V/470uF)
ELECT(16V/100uF)
ELECT(10V/470uF)
66
KR3-16V101MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-50V220MA(5*11L)
KR3-50V220MA(5*11L)
KR3-50V220MA(5*11L)
KR3-50V220MA(5*11L)
KR3-50V220MA(5*11L)
KR3-50V220MA(5*11L)
KR3-50V220MA(5*11L)
KR3-50V220MA(5*11L)
KR3-16V101MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-25V101MB(6.3*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-25V101MB(6.3*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-16V101MA(5*11L)
KC3-16V101MA5(6.3*5L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-50V4R7MA(5*11L)
KR3-16V101MA(5*11L)
KR3-10V471MB(6.3*11L)
KR3-16V101MA(5*11L)
KR3-10V471MB(6.3*11L)
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C730
C735
C740
C749
C750
C752
C753
C764
C786
C787
C799
C844
C845
C847
C861
C862
C863
C868
D221
D222
D803
D804
Q311
BN52
CN11
CN19
CN20
CN51
CN62
CN71
C732
ET70
IC102
IC103
JK11
JK12
JK52
JK75
JK76
JK78
JK79
L301
L302
TUN1
WF101
WF103
X701
X702
X703
X705
X708
X777
Description
COP12327D
CCEA1CH101T
CCEA1AH471T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA0JH102T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CKS101T
CCEA1HKS1R0T
CCEA1CKS101T
CCEA1CKS100T
CCEA1CKS101T
CCEA1CKS101T
CCEA1EH470T
CVD1N4003SRT
CVD1N4003SRT
CVD1N4003SRT
CVD1N4003SRT
HVTKTC2874BT
CWB1C005200EN
CJP06GA19ZY
CJP06GA19ZY
CJP11GI237ZW
CJP05GA01ZY
CJP64GA221ZB
CJP18GB143ZB
CCEA0JKR3222E
CMD1A569
HVIKIA7808API
CVIKIA7908PI
CJJ4P019W
CJJ4R020W
CJJ9L015Z
HJSTORX147L
HJSTORX147L
CJJ4N075Z
HJSTOTX177AL
CLM4B001Z
CLM4B001Z
CNVMW004MV1S63SA
CJP27GA285ZN
CJP27GA285ZN
HOX24576E150TF
HOX10000E220TF
COX09000E150C
HOX10000E220TF
HOX00032K120I
COX25000E180C
KR3-16V101MA(5*11L)
KR3-10V471MB(6.3*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
CAP , ELECT(1000uF/6.3V)
1000UF 6.3V
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
CAP , ELECT(16V/100uF)-S
KC3-16V101MA5(6.3*5L)
KC3-50V010MA2(4*5L)
KC3-16V101MA5(6.3*5L)
KC3-16V100MA2(4*5L)
KC3-16V101MA5(6.3*5L)
KC3-16V101MA5(6.3*5L)
KR3-25V470MA(5*11L)
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
TRANSISTOR , MUTE
KTC2874B
WIRE ASS'Y(5P, 200MM, 2.0MM) 5P, 2.0MM, 200MM
WAFER,20017WS(2mm,STRAIGHT)
WAFER,20017WS(2mm,STRAIGHT)
LOCK-WAFER/STRAIGHT/2.5mm JWT A2512WV0-NP
WAFER,YMW025(2.5mm,STRAIGHT)
WAFER , 2.54MM 64PIN WAFER
FEMALE HEADER (18P, 2.54mm), ANGLE TYPE
BRACKET , PCB
I.C,REGULATOR(+8V,T0220IS)
KIA7808API (KEC)
I.C,REGULATOR(-8V,T0220IS)
KIA7908PI (KEC)
JACK , RCA
JACK , BOARD
JACK , RJ-45(WITH FILTER)
TM00640
MODULE , OPTICAL (RX,3.3V)
MODULE , OPTICAL (RX,3.3V)
JACK , 2P(GOLD PLATE)
RCA-215AG-01
MODULE , OPTICAL(TX)
COIL , MPX(FM 19KHz FILTER)
COIL , MPX(FM 19KHz FILTER)
TUNER(USA) FM(SCREW:F TYPE,AM(S/LAB)KST-MW004MV1-S63SA
1.25-2-NP
1.25-2-NP
CRYSTAL, 24.576MHz, HC-49/S, 15pF, 30PPM
24.576MHZ
CL-22P
CL-22P
CRYSTAL, 32.768KHz, TUNING FORK, 12pF, 20PPM
67
AVR 2650
Reference
Designator
harman/kardon
Part Number
HDMI PCB ASS'Y

CN104
CN105
C101
C102
C104
C105
C106
C107
C108
C109
C110
C111
C113
C115
C116
C117
C118
C119
C120
C121
C122
C123
C124
C125
C126
C127
C128
C129
C130
C131
C132
C133
C134
C135
C136
C137
C138
C140
C141
C142
C152
C153
C154
C156
C158
C159
C160
C161
C162
C163
C164
C165
C166
Description
COP12328D
CJP17GB210ZY
CJP17GB210ZY
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCUI1E103KC
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCUC0J106KC
CCUC0J106KC
CCUC0J106KC
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCUI1E103KC
CCUI1E103KC
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCUI1E103KC
CCUI1E103KC
CCUI1E103KC
CCUI1C104KC
CCUI1E103KC
CCUI1E103KC
CCUI1C104KC
CCUI1E103KC
CCUC0J106KC
CCUC0J106KC
CCUC0J106KC
CCUC0J106KC
CCSNA0J220B
CCSNA0J220B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA0J220B
CCSNA0J220B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
WAFER,(CARD CABLE,ANGLE,SMT,1MM,10008HR-17L(P) 10008HR-17L

WAFER,(CARD CABLE,ANGLE,SMT,1MM,10008HR-17L(P) 10008HR-17L
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(2012, 6.3V/10uF)
CAP, CHIP(2012, 6.3V/10uF)
CAP, CHIP(2012, 6.3V/10uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP, CHIP(2012, 6.3V/10uF)
CAP, CHIP(2012, 6.3V/10uF)
CAP, CHIP(2012, 6.3V/10uF)
CAP, CHIP(2012, 6.3V/10uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
68
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C168
C169
C171
C172
C173
C174
C175
C176
C177
C178
C179
C180
C181
C183
C184
C186
C187
C188
C189
C191
C192
C193
C194
C195
C196
C197
C198
C200
C201
C202
C203
C204
C206
C208
C211
C212
C213
C214
C216
C217
C218
C219
C220
C221
C222
C223
C224
C225
C227
C229
C230
C231
C232
Description
COP12327D
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA0J220B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUS1H104KC
CCSNA1C100B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA0J220B
CCUI1C104KC
CCUI1C104KC
CAP , CHIP (1005, 16V/0.1uF)

CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , CHIP TANTAL(10uF/16V, NingXia XingRi)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
69
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C233
C234
C235
C236
C237
C238
C239
C243
C244
C245
C246
C248
C249
C250
C251
C255
C256
C257
C258
C259
C263
C264
C266
C267
C268
C269
C270
C271
C274
C275
C276
C277
C280
C283
C284
C285
C287
C288
C289
C290
C295
C296
C297
C298
C300
C301
C302
C303
C305
C306
C307
C308
C309
Description
COP12327D
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA1C100B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA0J220B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA1C100B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA1C100B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
CAP
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
TANTAL(10uF/16V, NingXia XingRi)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
TANTAL(22uF/6.3V, NingXia XingRi)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
(1005, 16V/0.1uF)
70
AVR 2650
Reference
Designator
harman/kardon
Part Number
Description
INPUT PCB ASS'Y

C310
C312
C314
C315
C316
C317
C318
C320
C322
C323
C324
C325
C326
C328
C329
C330
C331
C332
C333
C334
C335
C336
C337
C338
C339
C340
C342
C343
C344
C345
C346
C348
C349
C351
C352
C353
C354
C355
C357
C358
C359
C361
C362
C363
C364
C366
C367
C369
C370
C371
C372
C373
C375
CCUI1C104KC
CCSNA1C100B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA0J220B
CCUI1C104KC
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA0J220B
CCUI1C104KC
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCSNA1C100B
CCSNA1C100B
CCUI1C104KC
CCUI1C104KC
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1E103KC
CCSNA0J220B
CCSNA1C100B
CCUI1C104KC
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA1C100B
CCSNA1C100B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA1C100B
COP12327D
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
71
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C376
C378
C379
C380
C381
C382
C383
C384
C385
C386
C387
C388
C390
C391
C392
C393
C394
C395
C396
C398
C399
C403
C406
C408
C409
C411
C413
C415
C418
C419
C420
C423
C425
C426
C427
C429
C430
C436
C438
C440
C442
C443
C445
C446
C450
C453
C454
C455
C457
C460
C462
C464
C467
Description
COP12327D
CCSNA1C100B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA1C100B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA0J220B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA0J220B
CCUI1C104KC
CCSNA1C100B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA0J220B
CCUS1H103KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA1C100B
CCSNA0J220B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUS1H104KC
CCUI1C104KC
CCUI1C104KC
CCUI1E103KC
CCSNA0J220B
CCUS1H104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA0J220B
CCUS1H104KC
CCUI1C104KC
CCUI1C104KC

CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1005, 25V/0.01uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
72
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C468
C470
C471
C475
C479
C480
C482
C483
C490
C491
C498
C501
C508
C514
C516
C519
C522
C523
C525
C529
C530
C532
C533
C536
C537
C538
C545
C546
C547
C549
C551
C552
C553
C555
D905
IC910
L803
L804
L805
L806
L807
L812
L813
L816
L818
L819
L820
L821
L822
L823
L824
L825
L826
Description
COP12327D
CCUI1C104KC
CCUS1H104KC
CCUI1C104KC
CCSNA0J220B
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA1C100B
CCUI1C104KC
CCUS1H104KC
CCSNA1C100B
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCSNA1C100B
CCUS1H104KC
CCSNA0J220B
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCSNA1C100B
CCUS1H103KC
CCUI1C104KC
CCSNA0J220B
CCSNA1C100B
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUI1E103KC
HVDUDZS5.1BSR
HVIKIC7SZ08FU
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9Z014Z
CLZ9R005Z
CLZ9Z014Z
CLZ9R005Z
CLZ9R005Z
CAP , CHIP (1005, 16V/0.1uF)

CAP, CHIP(1608, 50V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1005, 25V/0.01uF)
DIODE , ZENER (CHIP,5.1V)
I.C ,INPUT AND GATE (USV PACKAGE)KIC7SZ08FU-RTK
FERRITE CHIP BEAD(1608/60ohm) HCB1608KF-600T30/COILMASTER
FERRITE , CHIP BEAD(60ohm, 4516) HCB4516KF-600T60/COILMASTER
FERRITE CHIP BEAD(1608/60ohm)
73
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

L827
L828
L829
L830
L831
L832
L833
L835
L837
L838
L840
L841
L843
L844
L847
L857
L861
L864
Q913
Q914
Q915
Q916
RN13
RN32
RN36
RN40
RN41
RN45
RN47
RN50
RN52
RN82
RN83
RN84
RN85
RN86
RN87
RN88
RN89
RN90
RN91
R602
R603
R605
R608
R609
R612
R614
R615
R619
R622
R623
R624
Description
COP12327D
CLZ9Z014Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9Z014Z
CLZ9R005Z
CLZ9Z014Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9Z014Z
CLZ9Z014Z
CLZ9Z014Z
CLZ9Z014Z
CLZ9Z014Z
CVTKRC103S
CVTKRC103S
CVTKRC103S
CVTUPA672T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ0R0T
CRJ064IJ0R0T
CRJ064IJ0R0T
CRJ064IJ0R0T
CRJ064IJ103T
CRJ064IJ0R0T
CRJ062IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ10DJ103T
CRJ10DJ103T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ222T
CRJ10DJ0R0T
CRJ10DJ222T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ222T
CRJ10DJ102T

F.E.T (NEC) UPA672T
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/0ohm*4)
RES, CHIP(1005/5%/10Kohm*4)
RES, CHIP(1005/5%/33ohm*2)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
74
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

R629
R631
R634
R637
R639
R648
R652
R656
R657
R660
R663
R664
R667
R668
R670
R672
R674
R675
R677
R678
R681
R682
R687
R688
R690
R692
R693
R694
R695
R696
R697
R707
R709
R711
R713
R714
R715
R717
R720
R729
R731
R733
R734
R737
R743
R745
R748
R756
R757
R760
R771
R774
R777
Description
COP12327D
CRJ10DJ101T
CRJ10DJ102T
CRJ10DJ101T
CRJ10DJ102T
CRJ10DJ102T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ473T
CRJ10DJ101T
CRJ10DJ102T
CRJ10DJ510T
CRJ10DJ103T
CRJ10DJ510T
CRJ10DJ103T
CRJ06IJ0R0T
CRJ06IJ0R0T
CRJ06IJ330T
CRJ06IJ472T
CRJ06IJ271T
CRJ10DJ510T
CRJ06IJ102T
CRJ06IJ220T
CRJ06IJ102T
CRJ06IJ220T
CRJ10DJ510T
CRJ06IJ0R0T
CRJ06IJ102T
CRJ10DJ472T
CRJ10DJ510T
CRJ10DJ472T
CRJ10DJ510T
CRJ10DJ472T
CRJ10DJ103T
CRJ06IJ330T
CRJ10DJ510T
CRJ10DJ510T
CRJ10DJ510T
CRJ06IJ103T
CRJ06IJ103T
CRJ06IJ103T
CRJ06IJ472T
CRJ06IJ103T
CRJ06IJ472T
CRJ06IJ472T
CRJ10DF2800T
CRJ06IJ0R0T
CRJ10DF2800T
CRJ06IJ472T
CRJ06IJ472T
CRJ06IJ220T
CRJ10DF4R99T
CRJ06IJ182T
CRJ10DF49R9T
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
CHIP(1608/5%/100ohm)
CHIP(1608/5%/1Kohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/1Kohm)
CHIP(1608/5%/1Kohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/1Kohm)
CHIP(1608/5%/51ohm)
CHIP(1608/5%/51ohm)
CHIP(1005/5%/0ohm)
CHIP(1005/5%/0ohm)
CHIP(1005/5%/33ohm)
CHIP(1005/5%/4.7Kohm)
CHIP(1005/5%/270ohm)
CHIP(1608/5%/51ohm)
CHIP(1005/5%/1Kohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/1Kohm)
CHIP(1005/5%/22ohm)
CHIP(1608/5%/51ohm)
CHIP(1005/5%/0ohm)
CHIP(1005/5%/1Kohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/51ohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1608/5%/51ohm)
CHIP(1608/5%/4.7Kohm)
CHIP(1005/5%/33ohm)
CHIP(1608/5%/51ohm)
CHIP(1608/5%/51ohm)
CHIP(1608/5%/51ohm)
CHIP(1005/5%/4.7Kohm)
CHIP(1005/5%/4.7Kohm)
CHIP(1005/5%/4.7Kohm)
CHIP(1608/1%/280ohm)
CHIP(1005/5%/0ohm)
CHIP(1608/1%/280ohm)
CHIP(1005/5%/4.7Kohm)
CHIP(1005/5%/4.7Kohm)
CHIP(1005/5%/22ohm)
CHIP(1608/1%/4.99ohm)
CHIP(1005/5%/1.8Kohm)
CHIP(1608/1%/49.9ohm)
75
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

R780
R785
R793
R795
R797
R799
R804
R822
R830
R836
R860
R863
R866
R867
R871
R875
R878
C103
C112
C114
C139
C143
C145
C146
C147
C148
C150
C151
C155
C157
C167
C182
C185
C199
C205
C207
C209
C210
C226
C240
C241
C247
C252
C253
C254
C260
C261
C262
C265
C272
C273
C278
C279
Description
COP12327D
CRJ06IJ182T
CRJ10DF49R9T
CRJ06IJ0R0T
CRJ10DF49R9T
CRJ06IJ0R0T
CRJ10DF49R9T
CRJ06IJ220T
CRJ06IJ182T
CRJ10DJ0R0T
CRJ06IJ182T
CRJ10DJ330T
CRJ10DJ330T
CRJ10DJ103T
CRJ10DJ103T
CRJ10DJ330T
CRJ10DJ101T
CRJ10DJ222T
CCUI1E103KC
CCUI1C104KC
CCUI1C104KC
CCUC0J106KC
CCUS1H470JA
CCUS1H470JA
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA0J220B
CCUS1H270JA
CCSNA1C100B
CCSNA1C100B
CCUS1H220JA
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCSNA1C100B
CCUC0J106KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
RES, CHIP(1608/1%/49.9ohm)
RES, CHIP(1608/1%/49.9ohm)
RES, CHIP(1608/1%/49.9ohm)
CAP, CHIP(1005, 25V/0.01uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(2012, 6.3V/10uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(2012, 6.3V/10uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
76
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C281
C282
C286
C291
C292
C293
C294
C299
C311
C313
C319
C321
C327
C341
C347
C350
C356
C360
C365
C368
C374
C377
C410
C424
C428
C431
C439
C441
C451
C452
C488
C489
C493
C494
C495
C500
C505
C506
C509
C510
C511
C512
C513
C515
C517
C518
C520
C521
C526
C527
C531
C534
C539
Description
COP12327D
CCUI1C104KC
CCUI1C104KC
CCUI1H470JA
CCUI1H470JA
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUS1H104KC
CCUS1H104KC
CCUS1A105KC
CCUI1C104KC
CCUS1A105KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUI1C104KC
CCUS1H104KC
CCUS1H104KC
CCUI1C104KC
CCUS1H221JA
CCUS1H104KC
CCEC1CRV471T
CCEC1ACEEX151TY
CCEC1ERV221T
CCEC1ERV221T
CCUS1H104KC
CCUS1H102KC
CCUS1H102KC
CCSNA1C100B
CCSNA1C100B
CCUS1H104KC
CCUS1H221JA
CCUS1H104KC
CCSNA1C100B
CCUS1H221JA
CCEC1ERV221T
CCEC1ERV221T
CCUS1H102KC
CAP , CHIP (1005, 16V/0.1uF)

CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , CHIP (1005, 16V/0.1uF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, SMD ELECT(16V/470uF) MANLEX RV, 10X10
CAP , ELEC SMD (150uF/10V,8X10.5,SANYO)10CE150EX
CAP , SMD ELECT(MANLEX, RV, 25V/220, 8X10)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/1000pF)
CAP, CHIP(1608, 50V/1000pF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/1000pF)
77
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

C542
C548
D902
D903
D904
IC901
IC902
IC903
IC904
IC905
IC906
IC907
IC907
IC908
IC909
IC911
IC912
IC915
IC916
IC917
IC918
IC922
IC923
IC924
IC925
IC927
IC929
IC930
JK92
JK93
JK94
JK95
JK96
JK97
L801
L802
L808
L809
L810
L811
L814
L815
L817
L842
L849
L851
L852
L853
L854
L855
L856
L858
L859
Description
COP12327D
CCUS1H104KC
CAP, CHIP(1608, 50V/0.1uF)
CCUS1H103KC
CAP, CHIP(1608, 50V/0.01uF)
CVDSS34SR
DIODE , SCHOTTKY (40V,3A, DO-214AC) DELTA
CVDSS34SR
CVDSS34SR
CVIADV3014BSTZ
I.C, HDMI1.4 Repeater(LQFP-144P) ADV3014BSTZ
CVIADV7844KBCZ
I.C, HDMI RX/Decoder(BGA-425P) ADV7844KBCZ
CVITC74VCX541FT
I,C, OCTAL BUS BUFFER (TOSHIBA) TC74VCX541FT
CVIA3S56D40FTPG5
I.C, 256MB DDR SDRAM(TOSPII-66P) A3S56D40FTPG5
CVI74FCT38072DCGI
I.C, CLOCK DRIVER (IDT) IDT74FCT38072DCGI,IDT
CVIFLI30336AC
I.C, VIDEO PROCESSOR (GENESIS)
FLI30336
CVIANAM1550AV
I.C, FLASH(CVIMX29LV320DTTI-70G)
CVIMX29LV320DTTI-70G I.C, FLASH MEMORY (32MBIT,TSOP-48P) MX29LV320DTTI
CVIA3S56D40FTPG5
CVIA3S56D40FTPG5
CVI74ALVCH16827DGG
I.C,BUFFER/DEIVER(TSSOP-56P)74ALVCH16827DGG,118/NXP SEMI
CVI74ALVCH16827DGG
CVI74ALVCH16827DGG
CVI74ALVCH16827DGG
CVINJU7754F05TE1
I.C , REGULATOR(SOT-23-5) NJU7754F05-TE1
CVIADV7511KSTZ
I.C , HDMI TX (LQFP-100P) ADV7511KSTZ
HVINJM2391DL125
CVISI8005QTL
IC , DCDC Converter (3.5A, SOP8) SANKEN SI8005QTL
CVIKIA1117BS50
I.C , REGULATOR(SOT-223) KIA1117BS50
CVIKIA7809AF
IC , REGULATOR (+9V,DPAK) KIA7809AF
CVISI8005QTL
HVINJM2391DL125
CVISI8005QTL
CJJ9H008Y
JACK, HDMI(TYPE-A, SMT-19P)
H050FS019G643BY
CJJ9H008Y
H050FS019G643BY
CJJ9H008Y
H050FS019G643BY
CJJ9H008Y
H050FS019G643BY
CJJ9H008Y
H050FS019G643BY
CJJ9H008Y
H050FS019G643BY
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9Z014Z
CLZ9R005Z
CLZ9R005Z
CLZ9R005Z
CLZ9Z014Z
CLZ9Z014Z
CLZ9Z014Z
CLQ12E100MRZ
COIL , SMD POWER (10UH/3A)
CMI-SPC9H45F-SERIES
CLZ9Z014Z
CLZ9Z014Z
CLZ9Z014Z
CLQ12E100MRZ
CMI-SPC9H45F-SERIES
CLQ12E100MRZ
CMI-SPC9H45F-SERIES
CLZ9Z014Z
78
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

L860
L862
L863
Q901
Q902
Q903
Q904
Q905
Q906
Q907
Q908
Q909
Q910
RN10
RN11
RN12
RN14
RN15
RN16
RN17
RN18
RN19
RN20
RN21
RN22
RN23
RN24
RN25
RN26
RN27
RN28
RN29
RN30
RN31
RN33
RN34
RN35
RN37
RN38
RN39
RN42
RN43
RN44
RN46
RN48
RN49
RN51
RN53
RN54
RN55
RN56
RN57
RN58
Description
COP12327D
CLZ9R005Z
CLQ12E100MRZ
CLZ9Z014Z
CVTKRC103S
CVTKRC103S
HVTKRA102S
CVTKRC103S
HVTKRA102S
CVTKRC103S
HVTKRA102S
HVTKRA102S
HVTKRA102S
CVTKRC103S
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ104DJ220T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ104DJ220T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ062IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ103T
CRJ064IJ330T
CRJ064IJ330T
CRJ062IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ062IJ330T
CRJ064IJ330T
CRJ062IJ330T
CRJ064IJ330T

CMI-SPC9H45F-SERIES
TRANSISTOR , CHIP , SOT-23
KRC103S
KRC103S
KRA102S
KRC103S
KRA102S
KRC103S
KRA102S
KRA102S
KRA102S
KRC103S
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES , CHIP , 22 OHM, 5% , 1608 X 4
22X4/2012
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES , CHIP , 22 OHM, 5% , 1608 X 4
22X4/2012
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*2)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/10Kohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*2)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*2)
RES, CHIP(1005/5%/33ohm*4)
RES, CHIP(1005/5%/33ohm*2)
RES, CHIP(1005/5%/33ohm*4)
79
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

RN59
RN60
RN61
RN72
RN73
RN74
RN75
RN76
RN77
RN78
RN79
RN80
RN81
R604
R606
R607
R610
R611
R613
R616
R618
R620
R621
R625
R626
R627
R628
R630
R635
R636
R638
R646
R647
R649
R650
R653
R654
R655
R658
R659
R661
R662
R666
R669
R673
R680
R685
R689
R691
R703
R705
R710
R716
Description
COP12327D
CRJ064IJ330T
CRJ064IJ330T
CRJ062IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ064IJ330T
CRJ10DJ101T
CRJ10DJ0R0T
CRJ10DF1001T
CRJ10DF1001T
CRJ10DF1001T
CRJ10DJ0R0T
CRJ10DJ103T
CRJ10DJ101T
CRJ10DJ222T
CRJ10DF8201T
CRJ10DJ473T
CRJ10DJ473T
CRJ10DJ102T
CRJ10DJ473T
CRJ10DJ223T
CRJ10DJ473T
CRJ10DJ102T
CRJ10DJ223T
CRJ10DJ223T
CRJ10DJ102T
CRJ10DJ223T
CRJ10DJ473T
CRJ10DJ102T
CRJ10DJ473T
CRJ10DJ473T
CRJ10DJ473T
CRJ10DJ223T
CRJ10DJ102T
CRJ10DJ473T
CRJ10DF1001T
CRJ10DF1001T
CRJ10DJ104T
CRJ10DJ0R0T
CRJ10DJ330T
CRJ06IJ0R0T
CRJ10DJ330T
CRJ06IJ330T
CRJ10DJ330T
CRJ06IJ472T
CRJ06IJ103T
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*2)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1005/5%/33ohm*4)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/0ohm)
CHIP(1608/1%/1Kohm)
CHIP(1608/1%/1Kohm)
CHIP(1608/1%/1Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/2.2Kohm)
CHIP(1608/1%/8.2Kohm)
CHIP(1608/5%/1Kohm)
CHIP(1608/5%/1Kohm)
CHIP(1608/5%/1Kohm)
CHIP(1608/5%/1Kohm)
CHIP(1608/5%/1Kohm)
CHIP(1608/1%/1Kohm)
CHIP(1608/1%/1Kohm)
CHIP(1608/5%/100Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/5%/33ohm)
CHIP(1005/5%/0ohm)
CHIP(1608/5%/33ohm)
CHIP(1005/5%/33ohm)
CHIP(1608/5%/33ohm)
CHIP(1005/5%/4.7Kohm)
80
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

R718
R719
R721
R722
R723
R724
R725
R726
R727
R728
R730
R732
R735
R736
R738
R739
R740
R741
R742
R744
R746
R747
R749
R750
R752
R753
R754
R755
R758
R761
R762
R763
R764
R765
R767
R768
R776
R779
R787
R792
R796
R826
R834
R838
R839
R840
R841
R843
R844
R845
R846
R847
R851
Description
COP12327D
CRJ06IJ103T
CRJ06IJ103T
CRJ06IJ560T
CRJ06IJ103T
CRJ06IJ0R0T
CRJ06IJ220T
CRJ06IJ560T
CRJ06IJ103T
CRJ06IJ220T
CRJ06IJ220T
CRJ06IJ103T
CRJ06IJ560T
CRJ06IJ220T
CRJ06IJ560T
CRJ06IJ220T
CRJ06IJ103T
CRJ06IJ220T
CRJ06IJ220T
CRJ06IJ103T
CRJ06IJ220T
CRJ06IJ560T
CRJ06IJ220T
CRJ06IJ103T
CRJ10DF1002T
CRJ06IJ220T
CRJ06IJ560T
CRJ10DF1002T
CRJ06IJ220T
CRJ06IJ220T
CRJ06IJ560T
CRJ06IJ103T
CRJ06IJ103T
CRJ06IJ220T
CRJ06IJ560T
CRJ06IJ103T
CRJ06IJ103T
CRJ10DJ103T
CRJ10DF8201T
CRJ10DJ0R0T
CRJ10DJ103T
CRJ10DF1001T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ123T
CRJ10DJ273T
CRJ10DJ512T
CRJ10DJ123T
CRJ10DJ202T
CRJ10DJ222T
CRJ10DJ103T
CRJ10DJ223T
CRJ10DJ512T
CRJ10DJ512T
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
CHIP(1005/5%/56ohm)
CHIP(1005/5%/0ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/56ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/56ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/56ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/56ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/56ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/56ohm)
CHIP(1005/5%/22ohm)
CHIP(1005/5%/56ohm)
CHIP(1608/1%/8.2Kohm)
CHIP(1608/5%/0ohm)
CHIP(1608/1%/1Kohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/100ohm)
CHIP(1608/5%/5.1Kohm)
CHIP(1608/5%/2Kohm)
CHIP(1608/5%/2.2Kohm)
CHIP(1608/5%/5.1Kohm)
CHIP(1608/5%/5.1Kohm)
81
10K /1/10W/F
10K /1/10W/F
AVR 2650
Reference
Designator
harman/kardon
Part Number
INPUT PCB ASS'Y

R852
R854
R856
R857
R859
R861
R862
R864
R865
R872
R873
R874
R879
R880
R881
R882
R883
R884
X901
X902
X903
BN301
BN61
C528
C179
C180
C181
C182
C183
C184
C185
C187
C188
C189
C190
C191
C192
C193
C194
C195
C196
C197
C198
C200
C202
C203
D705
D706
D707
COP12327D
CRJ10DJ202T
CRJ06IJ472T
CRJ06IJ472T
CRJ10DJ103T
CRJ10DJ330T
CRJ10DJ330T
CRJ10DJ330T
CRJ06IJ472T
CRJ10DJ103T
CRJ10DJ623T
CRJ10DJ623T
CRJ10DJ623T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ104T
CRJ10DJ104T
COX28636E330S
COX28636E330S
COX19660E330S
CMY1A297
CJP30GB143ZB
CWB1D00718058
CCEA1EH222E
VIDEO PCB ASS'Y
Description
CRYSTAL, 28.636MHz, HC-49/SMD, 33pF, 30PPM
HEAT SINK
DIP, SOCKET(30PIN, 2.54mm,ANGLE)
WIRE ASS'Y (2.5mm, 7p, 180mm)
CAP , ELECT(25V/2200uF) 2200UF 25V
COP12361D
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H223KC
CCUS1H104KC
CCUS1H223KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H223KC
CCUS1H104KC
CCUS1H223KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H220JA
CCUS1H220JA
CVD1SS355T
CVD1SS355T
CVD1SS355T
CAP, CHIP(1608, 50V/0.1uF)

CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
DIODE, SMD, SWITCHING
1SS355/SOD-323
1SS355/SOD-323
1SS355/SOD-323
82
AVR 2650
Reference
Designator
harman/kardon
Part Number
VIDEO PCB ASS'Y

D708
L802
R567
R568
R569
R570
R571
R572
R573
R574
R578
R579
R580
R581
R582
R583
R584
R585
R586
R587
R589
R591
R592
R593
R594
R596
R602
R603
R605
R606
R608
C101
C102
C103
C104
C105
C108
C109
C110
C111
C112
C113
C114
C115
C116
C117
C118
C119
C120
C121
C122
C123
C124
Description
COP12361D
CVD1SS355T
CLZ9Z014Z
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ103T
CRJ10DJ104T
CRJ10DJ104T
CRJ10DJ332T
CRJ10DJ4R7T
CRJ10DJ474T
CRJ10DJ220T
CRJ10DJ474T
CRJ10DJ220T
CRJ10DJ0R0T
CRJ10DJ220T
CRJ10DJ220T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ102T
CRJ10DJ0R0T
CRJ10DJ4R7T
CRJ10DJ4R7T
CRJ10DJ0R0T
CRJ10DJ0R0T
CRJ10DJ0R0T
CCUS1H472KC
CCUS1H472KC
CCUS1H472KC
CCUS1H221JA
CCUS1H221JA
CCUS1H102KC
CCUS1H102KC
CCUS1H020CA
CCUS1H020CA
CCUS1H020CA
CCUS1H020CA
CCUS1H020CA
CCUS1H020CA
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUS1H103KC
CCUS1H330JA
CCUS1H330JA
CCUS1H330JA

1SS355/SOD-323
FERRITE , CHIP BEAD(60ohm,4516)HCB4516KF-600T60/COILMASTER
CAP, CHIP(1608, 50V/4700pF)
CAP, CHIP(1608, 50V/4700pF)
CAP, CHIP(1608, 50V/4700pF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/1000pF)
CAP, CHIP(1608, 50V/1000pF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
83
AVR 2650
Reference
Designator
harman/kardon
Part Number
VIDEO PCB ASS'Y

C143
C144
C145
C146
C147
C148
C162
C164
C165
C166
C204
C205
C206
D704
IC901
IC903
IC904
IC905
IC906
IC907
IC908
IC909
IC910
IC911
IC912
IC918
L801
Q901
Q904
Q905
Q906
Q908
R501
R502
R503
R504
R505
R506
R507
R508
R509
R510
R511
R512
R513
R514
R515
R516
R517
R518
R519
R520
R521
Description
COP12361D
CCUS1H103KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H330JA
CCUS1H330JA
CCUS1H223KC
CCUS1H103KC
CCUS1H104KC
CCUS1H104KC
CCUS1A105KC
CCUS1A105KC
CCUS1A105KC
CVD1SS355T
CVINJW1321FP1
CVIKIA7809AF
CVIKIA1117BS50
CVINJM2595MTE1
HVI74HCU04AFNG
CVIAZ4580MTR-E1
CVITL072CDR
CVINJM2505AFTE1
CVINJM2505AFTE1
HVINJM2581MTE1
CVINJM2505AFTE1
CVIILX3232DT
CLZ9Z014Z
HVTKRC102S
HVTKRC102S
HVTKRA102S
HVTKRC102S
HVTKRC107S
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ750T
CRJ10DJ102T
CRJ10DJ222T
CRJ10DJ473T
CRJ10DJ102T
CRJ10DJ102T
CRJ10DJ473T
CRJ10DF1002T
CRJ10DF1002T
CRJ10DF5101T
CRJ10DF5101T
CRJ10DF4992T
CAP, CHIP(1608, 50V/0.01uF)

CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.022uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
1SS355/SOD-323
I.C , VIDEO S/W (JRC) NJW1321FP1
IC , REGULATOR (+9V,DPAK) KIA7809AF
I.C , REGULATOR(SOT-223) KIA1117BS50
I.C , VIDEO S/W (JRC) NJM2595MTE1
I.C , INVERTER (TOSHIBA) TC74HCU04AFNG(TOSHIBA)
I.C , OPAMP(DUAL LOW NOISE)AZ4580MTR-E1/SOIC8/BCD
I.C , OP AMP/SOP/8P (TI) TL072CDR
I.C , VIDEO AMP(4.5~9.0V,200MW,MTP5)JRC NJM2505AF-TE1
I.C (JRC)NJM2581MTE1 Dual Supply Wide Band 3ch Video Amplifier
I.C, RS232 DRIVER(3.3V) ILX3232D
KRC102S
KRC102S
KRA102S
KRC102S
10K /1/10W/F
10K /1/10W/F
1608 SIZE
1608 SIZE
84
AVR 2650
Reference
Designator
harman/kardon
Part Number
VIDEO PCB ASS'Y

R522
R523
R524
R525
R526
R527
R528
R529
R533
R534
R538
R539
R540
R541
R542
R543
R544
R545
R546
R547
R548
R549
R550
R552
R553
R556
R557
R559
R561
R562
R563
R575
R576
R577
C106
C107
C125
C126
C127
C128
C129
C130
C131
C132
C133
C134
C135
C136
C137
C138
C139
C140
C141
Description
COP12361D
CRJ10DF4992T
CRJ10DF4992T
CRJ10DF1001T
CRJ10DF4992T
CRJ10DF4992T
CRJ10DF1001T
CRJ10DF1001T
CRJ10DF4992T
CRJ10DJ101T
CRJ10DJ103T
CRJ10DJ750T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ750T
CRJ10DJ101T
CRJ10DJ101T
CRJ10DJ750T
CRJ10DJ101T
CRJ10DJ222T
CRJ10DJ474T
CRJ10DJ271T
CRJ10DJ271T
CRJ10DJ0R0T
CRJ10DJ103T
CRJ10DJ103T
CRJ10DJ102T
CRJ10DJ0R0T
CRJ10DJ103T
CRJ10DJ4R7T
CRJ10DJ4R7T
CRJ10DJ103T
CRJ10DJ330T
CRJ10DJ330T
CRJ10DJ102T
CCEA1EH221T
CCEA1CH471T
CCEA1HH100T
CCEA1HH100T
CCEA1AH471T
CCEA1HH4R7T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH1R0T
CCEA1HH1R0T
CCEA1HH1R0T
CCEA1HH1R0T
CCEA1HH1R0T
CCEA1HH1R0T
RES, CHIP(1608/5%/4.7ohm) 1608 SIZE
RES, CHIP(1608/5%/4.7ohm) 1608 SIZE
CAP , ELECT(25V/220uF) KR3-25V221MC(8*11.5L)
CAP , ELECT(16V/470uF) KR3-16V471MC(8*11.5L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
CAP , ELECT(10V/470uF) KR3-10V471MB(6.3*11L)
CAP , ELECT(50V/4.7uF) KR3-50V4R7MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V010MA(5*11L)
KR3-50V010MA(5*11L)
KR3-50V010MA(5*11L)
KR3-50V010MA(5*11L)
KR3-50V010MA(5*11L)
KR3-50V010MA(5*11L)
85
AVR 2650
Reference
Designator
harman/kardon
Part Number
VIDEO PCB ASS'Y

C142
C149
C150
C151
C152
C153
C154
C155
C156
C157
C158
C159
C160
C161
C163
C168
C169
C170
C171
C172
C173
C174
C175
C176
C177
Q903
Q907
BN51
BN53
CN40
CN41
CN52
IC902
IC913
JK91
JK92
JK93
JK94
JK95
JK96
C501
C502
C503
C505
C506
C507
C508
C509
C510
C561
COP12361D
CCEA1CH101T
CCEA1HH100T
CCEA1HH4R7T
CCEA1HH100T
CCEA1CH101T
CCEA1CH221T
CCEA1HH100T
CCEA1CH470T
CCEA1HH100T
CCEA1CH470T
CCEA1HH100T
CCEA1CH470T
CCEA1CH101T
CCEA1HH100T
CCEA1CH470T
CCEA1AH471T
CCEA1AH471T
CCEA1HH100T
CCEA1AH471T
CCEA1AH471T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
HVTKTA1266YT
HVTKTA1266YT
CWB1D00910058
CJP18GB142ZB
CJP09GI237ZW
CJP30GB142ZB
CJP05GB46ZY
CVIKIA7905PI
HVIKIA7812API
CJJ4R046Z
CJJ4P074Z
CJJ9N007Z
CJJ9L016Z
CJJ9W001Z
CJJ2D008Z
MAIN PCB ASS'Y
Description
CAP , ELECT(16V/100uF) KR3-16V101MA(5*11L)

KR3-50V100MA(5*11L)
CAP , ELECT(50V/4.7uF) KR3-50V4R7MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-16V470MA(5*11L)
KR3-50V100MA(5*11L)
KR3-16V470MA(5*11L)
KR3-50V100MA(5*11L)
KR3-16V470MA(5*11L)
KR3-50V100MA(5*11L)
KR3-16V470MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
TRANSISTOR
KTA1266YT
TRANSISTOR
KTA1266YT
WIRE ASS'Y (9PIN, 2.5mm,100mm,STRAIGHT,#22)
PIN HEADER (18P, 2.54mm) , ANGLE TYPE
LOCK-WAFER/STRAIGHT/2.5mm
30PIN, 2.54MM PIN HEADER
WAFER,20017WR(2mm,ANGLE)
I.C,REGULATOR(-5V,T0220IS) KIA7905PI (KEC)
I.C,REGULATOR(+12V,T0220IS) KIA7812API
JACK , BOARD
JACK , RCA(4P, GOLD PLATE (Y/Y/Y/Y) 100861
JACK , DIN SOCKET(8P)
N-801
JACK , IPOD CONNECTOR (36PIN) SI36P
JACK, 9P D-SUB FEMALE(RS-232C) -9PF-RSB/SEMCO
JACK, STEREO (BLK MOLD)
-308-02/YUQIU
COP12364D
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCKT1H331KB
CCBS1H331KBT
CCBS1H331KBT
CCKT1H331KB
CCBS1H331KBT
CCEA1CH101T
CAP, CERAMIC(50V/330pF/K)
CAP , CERAMIC(330PF/50V)
86
3-50V100MA(5*11L)
3-50V100MA(5*11L)
3-50V100MA(5*11L)
3-50V100MA(5*11L)
UP025 B331K-A-B Z
UP025 B331K-A-B Z
UP025 B331K-A-B Z
3-16V101MA(5*11L)
AVR 2650
Reference
Designator
harman/kardon
Part Number
Description
MAIN PCB ASS'Y

C562
C563
C564
C565
C566
C567
C568
C569
C570
C571
C572
C573
C574
C575
C601
C602
C603
C604
C605
C606
C607
C608
C609
C610
C631
C634
C635
C636
C639
C640
C649
C650
C681
C682
C683
C684
C685
C704
C716
C725
C801
C802
C803
C804
C805
C806
C807
C808
C809
C810
C811
C812
C813
COP12364D
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
CCBS1H681KBT
CCBS1H681KBT
CCBS1H681KBT
CCBS1H681KBT
CCBS1H681KBT
CCCT1H120JC
CCCT1H120JC
CCCT1H120JC
CCCT1H120JC
CCCT1H120JC
CCCT1H330JC
CCCT1H330JC
CCCT1H330JC
CCCT1H330JC
CCCT1H330JC
CCEA1JH470TS
CCEA1JH470TS
CCEA1JH470TS
CCEA1JH470TS
CCEA1JH470TS
CCEA1JH470TS
CCEA1HHR15T
CCBS1H104ZFT
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCKT1H102KB
CCEA1CH220T
CCKT1H221KB
CCEA1HH100T
CCEA1HH100T
CCCT1H330JC
CCCT1H330JC
CCCT1H120JC
CCCT1H120JC
CCEA1JH470TS
CCEA1JH470TS
CCEA1JH470TS
CCEA1JH470TS
CCEA1CH101T
CCEA1CH101T
CCEA1CH101T
3-16V101MA(5*11L)
3-16V101MA(5*11L)
3-16V101MA(5*11L)
3-16V101MA(5*11L)
3-16V101MA(5*11L)
3-16V101MA(5*11L)
3-16V101MA(5*11L)
3-16V101MA(5*11L)
3-16V101MA(5*11L)
UP025 B681K-A-B Z
UP025 B681K-A-B Z
UP025 B681K-A-B Z
UP025 B681K-A-B Z
UP025 B681K-A-B Z
CAP , CERAMIC
12PF 50V J
CAP , CERAMIC
12PF 50V J
CAP , CERAMIC
12PF 50V J
CAP , CERAMIC
12PF 50V J
CAP , CERAMIC
12PF 50V J
CAP , CERAMIC
33PF 50V J
CAP , CERAMIC
33PF 50V J
CAP , CERAMIC
33PF 50V J
CAP , CERAMIC
33PF 50V J
CAP , CERAMIC
33PF 50V J
CAP , ELECT
63V/47UF/105'C
CAP , ELECT
63V/47UF/105'C
CAP , ELECT
63V/47UF/105'C
CAP , ELECT
63V/47UF/105'C
CAP , ELECT
63V/47UF/105'C
CAP , ELECT
63V/47UF/105'C
CAP , ELECT(50V/0.15uF)
0.15UF 50V
CAP , CERAMIC
0.1UF 50V Z
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-16V220MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
CAP , CERAMIC
33PF 50V J
CAP , CERAMIC
33PF 50V J
CAP , CERAMIC
12PF 50V J
CAP , CERAMIC
12PF 50V J
CAP , ELECT
63V/47UF/105'C
CAP , ELECT
63V/47UF/105'C
CAP , ELECT
63V/47UF/105'C
CAP , ELECT
63V/47UF/105'C
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V101MA(5*11L)
87
AVR 2650
Reference
Designator
harman/kardon
Part Number
MAIN PCB ASS'Y

C814
C815
C816
C817
C818
C819
C820
C851
C852
C853
C854
C855
C856
C857
C900
C901
C905
C907
C908
C910
C913
C914
C917
C918
C919
C924
C925
C927
C932
C936
C939
C940
C950
C951
C971
C972
C973
C974
C975
C977
C980
C981
C990
C991
C992
C993
C994
C995
C996
C997
C999
D501
D502
Description
COP12364D
CCEA1CH101T
CCKT1H331KB
CCBS1H331KBT
CCEA1HH100T
CCEA1HH100T
CCBS1H681KBT
CCBS1H681KBT
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
CCEA1HH100T
HCQI1H473JZT
HCQI1H473JZT
CCBS1H223ZFT
CCEA1CH101T
CCBS1H223ZFT
HCQI1H473JZT
CCFT1H104ZF
HCQI1H473JZT
HCQI1H473JZT
HCQI1H473JZT
HCQI1H473JZT
CCFT1H104ZF
CCEA1HH2R2T
CCKT1H102KB
CCEA1CH101T
CCEA1CH221T
CCEA1HH4R7T
CCEA1AH471T
CCEA1AH471T
CCEA1HH470T
HCQI1H562JZT
HCQI1H562JZT
HCQI1H562JZT
HCQI1H562JZT
HCQI1H562JZT
CCEA1HH2R2T
HCQI1H562JZT
HCQI1H562JZT
HCQI1H473JZT
CCEA1HH1R0T
HCQI1H473JZT
HCQI1H473JZT
HCQI1H473JZT
HCQI1H473JZT
HCQI1H473JZT
HCQI1H473JZT
CCBS1H223ZFT
CVD1SS133MT
CVD1SS133MT
KR3-16V101MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
KR3-50V100MA(5*11L)
CAP , MYLAR
0.047UF 50V J
CAP , MYLAR
0.047UF 50V J
CAP , CERAMIC(22000PF/50V)CH UP025 F223Z-A-B J
KR3-16V101MA(5*11L)
CAP , CERAMIC(22000PF/50V)CH UP025 F223Z-A-B J
CAP , MYLAR
0.047UF 50V J
CAP , SEMICONDUCTOR
0.1UF 50V Z
CAP , MYLAR
0.047UF 50V J
CAP , MYLAR
0.047UF 50V J
CAP , MYLAR
0.047UF 50V J
CAP , MYLAR
0.047UF 50V J
CAP , SEMICONDUCTOR
0.1UF 50V Z
KR3-50V2R2MA(5*11L)
KR3-16V101MA(5*11L)
KR3-16V221MB(6.3*11L)
KR3-50V4R7MA(5*11L)
KR3-10V471MB(6.3*11L)
KR3-10V471MB(6.3*11L)
KR3-50V470MB(6.3*11L)
CAP , MYLAR
5600PF 50V J
CAP , MYLAR
5600PF 50V J
CAP , MYLAR
5600PF 50V J
CAP , MYLAR
5600PF 50V J
CAP , MYLAR
5600PF 50V J
KR3-50V2R2MA(5*11L)
CAP , MYLAR
5600PF 50V J
CAP , MYLAR
5600PF 50V J
CAP , MYLAR
0.047UF 50V J
KR3-50V010MA(5*11L)
CAP , MYLAR
0.047UF 50V J
CAP , MYLAR
0.047UF 50V J
CAP , MYLAR
0.047UF 50V J
CAP , MYLAR
0.047UF 50V J
CAP , MYLAR
0.047UF 50V J
CAP , MYLAR
0.047UF 50V J
CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
88
AVR 2650
Reference
Designator
harman/kardon
Part Number
MAIN PCB ASS'Y

D503
D504
D505
D581
D582
D583
D584
D585
D701
D801
D802
D803
D804
D901
D903
D912
D914
D915
D917
D950
D953
D954
D955
D956
D957
D961
D962
D963
D964
D967
D968
D969
D971
D972
D975
D976
D979
ET90
ET91
F901
Q501
Q502
Q503
Q504
Q505
Q511
Q512
Q513
Q514
Q515
Q516
Q517
Q518
Description
COP12364D
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1N4003ST
CVD1SS133MT
CVD1SS133MT
C3A206
CVD1N4003ST
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1N4003SRT
CVD1N4003SRT
CVD1N4003ST
CVD1N4003ST
CVD1N4003ST
CVD1N4003ST
CVD1N4003ST
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVD1SS133MT
CVDZJ4.3BT
HJT1A025
HJT1A025
KJCFC5S
HVTKTA1268GRT
HVTKTA1268GRT
HVTKTA1268GRT
HVTKTA1268GRT
HVTKTA1268GRT
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , RECT
1N4003
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
WIRE , COPPER
SN95/PB5 , 0.6
DIODE , RECT
1N4003
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , SWITCHING
1SS133
DIODE , ZENER 4.3V
ZJ4.3B 1/2W
PLATE , EARTH
MET37-0002
PLATE , EARTH
HOLDER , FUSE
2.0
TRANSISTOR
KTA1268GR
TRANSISTOR
KTA1268GR
TRANSISTOR
KTA1268GR
TRANSISTOR
KTA1268GR
TRANSISTOR
KTA1268GR
TRANSISTOR, 2SC2240BL (NPN, TO-92, LOW NOISE,
89
TOSH
TOSH
TOSH
TOSH
TOSH
TOSH
TOSH
TOSH
AVR 2650
Reference
Designator
harman/kardon
Part Number
MAIN PCB ASS'Y

Q519
Q520
Q541
Q542
Q543
Q544
Q545
Q556
Q557
Q558
Q559
Q560
Q561
Q563
Q564
Q565
Q601
Q602
Q603
Q604
Q605
Q641
Q642
Q681
Q682
Q683
Q684
Q685
Q701
Q702
Q703
Q704
Q705
Q716
Q801
Q802
Q812
Q813
Q814
Q815
Q816
Q817
Q818
Q819
Q820
Q821
Q822
Q823
Q824
Q825
Q901
Q911
Q912
Description
COP12364D
CVT2SC2240BL
CVT2SC2240BL
HVTKTC3198YT
HVTKTC3198YT
HVTKTC3198YT
HVTKTC3198YT
HVTKTC3198YT
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
HVTKTA1268GRT
HVTKTA1268GRT
HVTKTA1268GRT
HVTKTA1268GRT
HVTKTA1268GRT
HVTKRC102MT
HVTKTC3199YT
HVTKTC3199YT
HVTKTC3199YT
HVTKTC3199YT
HVTKTC3199YT
HVTKTC3199YT
HVTKTA1268GRT
HVTKTA1268GRT
HVTKTC3199YT
HVTKTA1267YT
HVTKRC107MT
HVTKTC3199YT
HVTKTC3199YT
HVTKTC3199YT
HVTKTA1268GRT
CVT2SC2240BL
HVTKTA1268GRT
CVT2SC2240BL
HVTKTA1268GRT
HVTKTA1268GRT
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
CVT2SC2240BL
HVTKTC3198YT
HVTKTC3198YT
HVTKTC3199YT
HVTKTA1271YT
HVTKTA1271YT
TRANSISTOR,
TRANSISTOR,
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR
TRANSISTOR
TRANSISTOR,
TRANSISTOR
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR
TRANSISTOR,
TRANSISTOR
TRANSISTOR,
TRANSISTOR
TRANSISTOR
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR,
TRANSISTOR
TRANSISTOR
TRANSISTOR,
TRANSISTOR
TRANSISTOR
2SC2240BL (NPN, TO-92, LOW NOISE, TOSH

KTC3198Y
KTC3198Y
KTC3198Y
KTC3198Y
KTC3198Y
KTA1268GR
KTA1268GR
KTA1268GR
KTA1268GR
KTA1268GR
TO-92M
KRC102M
KTC3199Y/TO-92M
KTC3199Y/TO-92M
KTC3199Y/TO-92M
KTC3199Y/TO-92M
KTC3199Y/TO-92M
KTC3199Y/TO-92M
KTA1268GR
KTA1268GR
KTC3199Y/TO-92M
KTA1267Y
KRC107M
KTC3199Y/TO-92M
KTC3199Y/TO-92M
KTC3199Y/TO-92M
KTA1268GR
2SC2240BL(NPN,TO-92,LOW NOISE,TOSH
KTA1268GR
2SC2240BL NPN,TO-92,LOW NOISE,TOSH
KTA1268GR
KTA1268GR
2SC2240BL(NPN,TO-92,LOW NOISE,TOSH
KTC3198Y
KTC3198Y
KTC3199Y/TO-92M
KTA1271Y
KTA1271Y
90
AVR 2650
Reference
Designator
harman/kardon
Part Number
MAIN PCB ASS'Y

Q913
Q915
Q916
Q917
Q938
Q939
Q941
Q942
Q943
Q950
Q951
Q952
Q960
Q961
R500
R501
R502
R503
R504
R505
R506
R507
R508
R509
R510
R511
R512
R513
R514
R515
R516
R517
R518
R519
R520
R521
R522
R523
R524
R525
R531
R532
R533
R534
R535
R536
R537
R538
R539
R540
R541
R542
R543
Description
COP12364D
HVTKTA1271YT
HVTKTC3199YT
HVTKTC3199YT
HVTKRC102MT
HVTKRA107MT
HVTKRA107MT
HVTKTC3199YT
HVTKTC3199YT
HVTKTC3199YT
HVTKTA1267YT
HVTKTC3198YT
HVTKTC3198YT
HVTKRC107MT
HVTKTA1024YT
CRD20TJ103T
CRD20TJ433T
CRD20TJ433T
CRD20TJ433T
CRD20TJ433T
CRD20TJ433T
CRD20TJ273T
CRD20TJ273T
CRD20TJ273T
CRD20TJ273T
CRD20TJ273T
CRD20TJ152T
CRD20TJ152T
CRD20TJ152T
CRD20TJ152T
CRD20TJ152T
CRD20TJ152T
CRD20TJ152T
CRD20TJ152T
CRD20TJ152T
CRD20TJ152T
CRD20TJ471T
CRD20TJ471T
CRD20TJ471T
CRD20TJ471T
CRD20TJ471T
CRD20TJ221T
CRD20TJ221T
CRD20TJ221T
CRD20TJ221T
CRD20TJ221T
CRD20TJ221T
CRD20TJ221T
CRD20TJ221T
CRD20TJ221T
CRD20TJ221T
CRD20TJ271T
CRD20TJ271T
CRD20TJ271T
TRANSISTOR KTA1271Y
TRANSISTOR, KTC3199Y/TO-92M
TRANSISTOR, KRC102M
TRANSISTOR, KRA107M
TRANSISTOR, KRA107M
TRANSISTOR KTA1267Y
TRANSISTOR KTC3198Y
TRANSISTOR KTC3198Y
TRANSISTOR, TO-92M
KRC107M
TRANSISTOR, KTA1024Y/TO-92L
91
AVR 2650
Reference
Designator
harman/kardon
Part Number
MAIN PCB ASS'Y

R544
R545
R556
R557
R558
R559
R560
R561
R562
R563
R564
R565
R566
R567
R568
R569
R570
R571
R572
R573
R574
R575
R576
R577
R578
R579
R580
R581
R582
R583
R584
R585
R586
R587
R588
R589
R590
R591
R592
R593
R594
R595
R596
R597
R598
R599
R600
R601
R602
R603
R604
R605
R606
Description
COP12364D
CRD20TJ271T
CRD20TJ271T
CRD20TJ273T
CRD20TJ273T
CRD20TJ273T
CRD20TJ273T
CRD20TJ273T
CRD20TJ132T
CRD20TJ132T
CRD20TJ132T
CRD20TJ132T
CRD20TJ132T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ100T
CRD20TJ100T
CRD20TJ100T
CRD20TJ100T
CRD20TJ100T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ223T
CRD20TJ223T
CRD20TJ223T
CRD20TJ223T
CRD20TJ223T
CRD20TJ223T
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
CARBON(1/5W,270ohm,J)
CARBON(1/5W,27Kohm,J)
CARBON(1/5W,1.3Kohm,J)
92
AVR 2650
Reference
Designator
harman/kardon
Part Number
MAIN PCB ASS'Y

R607
R608
R609
R610
R611
R612
R631
R632
R633
R634
R635
R636
R637
R638
R639
R640
R643
R644
R645
R646
R647
R648
R649
R650
R651
R652
R653
R654
R655
R666
R667
R668
R669
R670
R671
R672
R673
R674
R675
R676
R677
R678
R679
R680
R681
R682
R683
R684
R685
R686
R687
R688
R689
Description
COP12364D
CRD20TJ223T
CRD20TJ223T
CRD20TJ223T
CRD20TJ223T
CRD20TJ100T
CRD20TJ100T
CRD25FJ180T
CRD25FJ180T
CRD25FJ180T
CRD25FJ180T
CRD25FJ180T
CRD25FJ180T
CRD25FJ180T
CRD25FJ180T
CRD25FJ180T
CRD25FJ180T
CRD20TJ472T
CRD20TJ472T
CRD20TJ102T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25TJ470T
CRD25TJ470T
CRD25TJ470T
CRD25TJ470T
CRD25TJ470T
CRD20TJ472T
CRD20TJ472T
CRD20TJ472T
CRD20TJ472T
CRD20TJ472T
CRD25TJ182T
CRD25TJ182T
CRD25TJ182T
CRD25TJ182T
CRD25TJ182T
CRD20TJ562T
CRD20TJ562T
CRD20TJ562T
CRD20TJ562T
CRD20TJ562T
CRD20TJ103T
CRD20TJ103T
CRD20TJ103T
CRD20TJ103T
RES , CARBON (18 OHM) NONFLAMMABLE
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
93
AVR 2650
Reference
Designator
harman/kardon
Part Number
MAIN PCB ASS'Y

R690
R696
R697
R698
R699
R700
R701
R702
R703
R704
R705
R708
R709
R710
R711
R712
R713
R714
R715
R716
R717
R771
R772
R773
R774
R775
R776
R777
R781
R782
R783
R784
R785
R786
R787
R801
R802
R803
R804
R805
R807
R808
R809
R812
R813
R814
R815
R817
R818
R819
R820
R821
R822
Description
COP12364D
CRD20TJ103T
CRD25TJ470T
CRD25TJ470T
CRD25TJ470T
CRD25TJ470T
CRD25TJ470T
CRD20TJ223T
CRD20TJ103T
CRD20TJ223T
CRD20TJ103T
CRD20TJ472T
CRD20TJ564T
C3A206
CRD20TJ1R0T
CRD20TJ272T
CRD20TJ473T
CRD20TJ563T
C3A206
CRD20TJ153T
CRD20TJ392T
CRD20TJ333T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ750T
CRD20TJ103T
CRD20TJ103T
CRD20TJ562T
CRD20TJ562T
CRD20TJ472T
CRD20TJ472T
CRD25TJ182T
CRD25TJ182T
CRD25TJ470T
CRD25TJ470T
CRD25TJ470T
CRD25TJ470T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25FJ3R3T
CRD25FJ180T
CRD25FJ180T
WIRE , COPPER
WIRE , COPPER
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
RES , CARBON
3.3 OHM 1/4W J
94
AVR 2650
Reference
Designator
harman/kardon
Part Number
MAIN PCB ASS'Y

R823
R824
R830
R831
R832
R833
R834
R835
R836
R837
R838
R839
R840
R841
R842
R843
R844
R845
R848
R849
R850
R851
R852
R853
R854
R855
R856
R857
R858
R859
R860
R861
R862
R863
R870
R871
R872
R873
R874
R875
R876
R877
R878
R879
R880
R882
R883
R884
R885
R886
R887
R888
R891
Description
COP12364D
CRD25FJ180T
CRD25FJ180T
CRD20TJ223T
CRD20TJ223T
CRD20TJ223T
CRD20TJ223T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ561T
CRD20TJ273T
CRD20TJ273T
CRD20TJ132T
CRD20TJ132T
CRD20TJ152T
CRD20TJ152T
CRD20TJ152T
CRD20TJ152T
CRD20TJ221T
CRD20TJ221T
CRD20TJ221T
CRD20TJ221T
CRD20TJ271T
CRD20TJ271T
CRD20TJ273T
CRD20TJ273T
CRD20TJ433T
CRD20TJ433T
CRD20TJ471T
CRD20TJ471T
CRD20TJ331T
CRD20TJ331T
CRD20TJ331T
CRD20TJ331T
CRD20TJ331T
CRD20TJ331T
CRD20TJ331T
CRD20TJ122T
CRD20TJ122T
CRD20TJ122T
CRD20TJ122T
CRD20TJ122T
CRD20TJ122T
CRD20TJ122T
CRD20TJ391T

95
AVR 2650
Reference
Designator
harman/kardon
Part Number
MAIN PCB ASS'Y

R892
R893
R894
R895
R896
R897
R901
R908
R909
R912
R915
R917
R918
R919
R920
R924
R925
R926
R927
R928
R929
R930
R933
R934
R935
R939
R940
R941
R942
R943
R944
R945
R946
R947
R952
R953
R954
R955
R956
R957
R958
R959
R960
R961
R962
R964
R965
R986
R987
R988
R989
R991
R998
Description
COP12364D
CRD20TJ391T
CRD20TJ391T
CRD20TJ391T
CRD20TJ391T
CRD20TJ391T
CRD20TJ391T
CRD20TJ272T
CRD20TJ333T
CRD20TJ333T
CRD20TJ332T
KRG1SANJ101RT
CRD25TJ393T
CRD25TJ393T
CRD25TJ393T
CRD25TJ393T
CRD20TJ473T
CRD20TJ473T
CRD20TJ473T
CRD20TJ104T
CRD20TJ222T
CRD20TJ222T
CRD20TJ222T
CRD20TJ472T
CRD20TJ153T
CRD20TJ562T
CRD20TJ472T
CRD20TJ152T
CRD25TJ223T
CRD20TJ223T
CRD20TJ223T
CRD25TJ223T
CRD25TJ223T
CRD25TJ223T
CRD20TJ223T
CRD25TJ223T
CRD20TJ223T
CRD20TJ223T
CRD20TJ563T
CRD20TJ274T
CRD20TJ153T
CRD20TJ563T
CRD20TJ104T
CRD20TJ103T
CRD20TJ331T
CRD20TJ273T
CRD20TJ223T
CRD20TJ223T
CRD20TJ102T
CRD20TJ561T
CRD20TJ562T
CRD20TJ302T
CRD20TJ822T
CRD20TJ103T
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
RES,
METAL(OXIDE)FILM,5%
100/1W(RADIAL)
96
AVR 2650
Reference
Designator
harman/kardon
Part Number
MAIN PCB ASS'Y

VR81
VR82
VR83
VR84
VR85
VR86
VR87
Q652
Q653
Q654
Q655
Q657
Q658
Q659
Q660
Q661
Q670
Q803
Q804
Q805
Q807
Q851
Q852
Q853
Q854
Q855
Q856
Q857
BN14
BN15
BN20
BN25
BN26
CN10
CN11
CN12
CN61
CN62
CN63
CN64
CN65
CN66
Description
COP12364D
CVN12A221B03T
CVN12A221B03T
CVN12A221B03T
CVN12A221B03T
CVN12A221B03T
CVN12A221B03T
CVN12A221B03T
CMYAVR2650
CFNRDH8025S
CHD1A012R
CHD1A036R
CHD3A012R
CMD1A417
CMD1A674
CMD1A694
CMY4A314
CTB3+8JR
CTW3+8JR
CVT2SB1560P43M
CVT2SB1560P43M
CVT2SB1560P43M
CVT2SB1560P43M
CVT2SD2390P43M
CVT2SD2390P43M
CVT2SD2390P43M
CVT2SD2390P43M
CVT2SB1560P43M
CVT2SD2390P43M
CVT2SD2390P43M
CVT2SB1560P43M
CVT2SD2390P43M
CVT2SB1560P43M
HVTKTD600KGR
HVTKTD600KGR
HVTKTD600KGR
HVTKTD600KGR
HVTKTD600KGR
HVTKTD600KGR
HVTKTD600KGR
CWB1D00718088
CWB1D00915088
CWB3F905300UZ
CWE8112120VV
CWE8112120VV
CJP03GA01ZY
CJP08GA221ZB
CJP27GA285ZN
CJP02GA01ZY
CJP02GA01ZY
CJP02GA01ZY
CJP02GA01ZY
CJP02GA01ZY
CJP02GA01ZY
RES , SEMI FIXED (220 OHM)NVZ6TLTAB221/HOKURIKU

HEAT SINK ASS'Y
MOTOR , FAN (80X80X25) 12V, 0.17A
SCREW , SPECIAL
14.0
SCREW , SPECIAL
4.0
SCREW , SPECIAL
12.0
BRACKET , PCB
AG-D8900
2.0
BRACKET , H/S
2.0
BRACKET , FAN
HEAT SINK
SCREW
6.0
SCREW
2.0
TRANSISTOR Power, 2SB1560, MT-100(TO3P) w MICA M43
TRANSISTOR Power, 2SD2390, MT-100(TO3P) w MICA M43
TRANSISTOR, BIAS
KTD600KGR
TRANSISTOR, BIAS
KTD600KGR
TRANSISTOR, BIAS
KTD600KGR
TRANSISTOR, BIAS
KTD600KGR
TRANSISTOR, BIAS
KTD600KGR
TRANSISTOR, BIAS
KTD600KGR
TRANSISTOR, BIAS
KTD600KGR
WIRE ASS'Y (2.5MM,180MM, 7PIN, DUAL-DIPP TYPE)
WIRE ASS'Y (2.5mm,150mm, 9pin, Dual-dip type)
WIRE ASS'Y (3.96mm, 300mm, 5pin)
WIRE ASS'Y (1PIN,120mm,LUG,#18,RED)
FEMALE HEADER (08P,2.54mm) , STRAIGHT TYPE
1.25-2-NP
97
AVR 2650
Reference
Designator
harman/kardon
Part Number
MAIN PCB ASS'Y

CN67
CN89
CN90
CN91
CN92
CN93
C632
C633
C637
C638
C904
C906
C915
C916
ET92
ET93
IC95
JK90
JK91
JK92
JW91
L501
L502
L503
L504
L505
L506
L507
Q858
Q871
Q872
Q874
Q875
Q876
Q877
Q881
Q882
Q883
Q884
Q885
Q886
Q887
RY94
R656
R657
R658
R659
R660
R706
R707
R810
R811
R905
Description
COP12364D
CJP02GA01ZY
CJP02GA01ZY
CJP02GA89ZY
CJP02GA89ZY
CJP02KA060ZY
CJP02GA01ZY
CCEA1JH221E
CCEA1JH221E
CCEA1JH221E
CCEA1JH221E
KCKDKS472ME
CCEA1VH102E
CCET63VKL5103NK
CCET63VKL5103NK
CMD1A569
CMD1A387
CVINJU7223F50
CJJ4M070Z
CJJ5R006Z
CJJ5Q012Z
CWE8112120VV
CLEY0R5KAK
CLEY0R5KAK
CLEY0R5KAK
CLEY0R5KAK
CLEY0R5KAK
CLEY0R5KAK
CLEY0R5KAK
HVTKTA1360Y
HVTKTA1360Y
HVTKTA1360Y
HVTKTA1360Y
HVTKTA1360Y
HVTKTA1360Y
HVTKTA1360Y
HVTKTC3423Y
HVTKTC3423Y
HVTKTC3423Y
HVTKTC3423Y
HVTKTC3423Y
HVTKTC3423Y
HVTKTC3423Y
CSL1C005ZE
CRF5EKR27HX2K
CRF5EKR27HX2K
CRF5EKR27HX2K
CRF5EKR27HX2K
CRF5EKR27HX2K
CRF5EKR10HS
CRF5EKR10HS
CRF5EKR27HX2K
CRF5EKR27HX2K
CRG1ANJ1R0H
WAFER, YW396-NNAB(7.92mm)
WAFER, YW396-NNAB(7.92mm)
WAFER
CAP , ELECT
220UF 63V
CAP , ELECT
220UF 63V
CAP , ELECT
220UF 63V
CAP , ELECT
220UF 63V
CAP , CERAMIC(X1/Y2/SC) 0.0047UF/2.5KV
CAP , ELECT(35V/1000uF) KR3-35V102MG(12.5*20L)
CAP , ELECT
CAP , ELECT
BRACKET , PCB
BRACKET , PCB
I.C , REGULATOR(5V, TO-220F) NJU7223F50
JACK , 1P(PURPLE) , GOLD PLATE RCA-107BAG-01
TERMINAL , SPEAKER
TERMINAL , SPEAKER
COIL , SPEAKER(0.5uH)
SPRING COIL 8TS/KSE
SPRING COIL 8TS/KSE
SPRING COIL 8TS/KSE
COIL , SPEAKER(0.5uH) SPRING COIL 8TS/KSE
TRANSISTOR , PRE DRIVE
KTA1360Y
KTA1360Y
KTA1360Y
KTA1360Y
KTA1360Y
KTA1360Y
KTA1360Y
KTC3423Y
KTC3423Y
KTC3423Y
KTC3423Y
KTC3423Y
KTC3423Y
KTC3423Y
RELAY (DC 5V, 1C1P)
HL3-1A-5SH
RES , CEMENT (0.27 OHM)
RES , CEMENT (SMALL SIZE)
RES , CEMENT (SMALL SIZE)
RES , METAL OXIDE FILM
1 OHM 1W J
98
AVR 2650
Reference
Designator
harman/kardon
Part Number
Description
MAIN PCB ASS'Y

R922
R923
R990
R993
R994
R995
R996
R997
R999
TH91
T902
CRG2ANJ470H
CRG1ANJ220H
CRG1ANJ100H
CRG1ANJ100H
CRG1ANJ100H
CRG1ANJ100H
CRG1ANJ100H
CRG1ANJ100H
CRG1ANJ100H
KRTP42T7D330B
CLT5I025ZU
DC-DC PCB ASS'Y

C123
C124
C127
C135
C136
C920
C921
C922
C923
C924
C925
C926
C936
C937
C950
C951
C952
C953
C954
C955
C956
C960
C961
C962
C963
C964
C965
C966
C967
D920
D950
D960
IC90
IC95
IC96
L900
L901
L902
L903
COP12364D
47 OHM
2W J
22 OHM 1W J
10 OHM 1W J
10 OHM 1W J
10 OHM 1W J
10 OHM 1W J
10 OHM 1W J
10 OHM 1W J
10 OHM 1W J
THERMAL SENSOR , POSISTOR
P42T7D330BW20
TRANS , SUB (AVR156X/1650/2650/3650)
COP12365D
CCUS1H473KC
CCUS1H473KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H104KC
CCUS1H221JA
CCUS1H104KC
CCUS1H103KC
CCUS1H103KC
CCUS1H104KC
CCEC1ACEEX151TY
CCUS1H473KC
CCUS1H473KC
CCUS1H104KC
CCUS1H221JA
CCUS1H104KC
CCUS1H103KC
CCUS1H103KC
CCUS1H104KC
CCEC1ACEEX151TY
CCEC1EHVH151TY
CCUS1H104KC
CCUS1H221JA
CCUS1H104KC
CCUS1H103KC
CCUS1H103KC
CCUS1H104KC
CCEC1ACEEX151TY
CVDSS34SR
CVDSS34SR
CVDSS34SR
CVISI8005QTL
CVISI8005QTL
CVISI8005QTL
CLQ12E100MRZ
CLZ9Z014Z
CLZ9Z014Z
CLZ9Z014Z
CAP, CHIP(1608, 50V/0.047uF)

CAP, CHIP(1608, 50V/0.047uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , ELEC SMD (150uF/10V, 8X10.5,SANYO)10CE150EX
CAP, CHIP(1608, 50V/0.047uF)
CAP, CHIP(1608, 50V/0.047uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , ELEC SMD (150uF/10V,8X10.5, SANYO) 10CE150EX
CAP , ELEC SMD (150uF/25V,8X10.5, SANYO) 25HVH150M
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/220pF)
CAP, CHIP(1608, 50V/0.1uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.01uF)
CAP, CHIP(1608, 50V/0.1uF)
CAP , ELEC SMD (150uF/10V, 8X10.5, SANYO) 10CE150EX
DIODE , SCHOTTKY (40V,3A, DO-214AC)DELTA SS34SR
DIODE , SCHOTTKY (40V,3A, DO-214AC)DELTA S34SR
DIODE , SCHOTTKY (40V,3A, DO-214AC)DELTA SS34SR
IC, DCDC Converter (3.5A, SOP8) SANKEN SI8005QTL
CMI-SPC9H45F-SERIES
99
AVR 2650
Reference
Designator
harman/kardon
Part Number
Description
DC-DC PCB ASS'Y

L904
L920
L950
L960
R120
R912
R913
R920
R921
R922
R923
R924
R925
R942
R950
R951
R952
R953
R954
R955
R960
R961
R962
R963
R964
R965
C131
C912
C939
C940
BN20
CN11
CN82
CN96
C129
C929
C930
IC83
IC84
CLZ9Z014Z
CLQ12E100MRZ
CLQ12E100MRZ
CLQ12E100MRZ
CRJ10DJ104T
CRJ10DJ153T
CRJ10DJ153T
CRJ10DJ223T
CRJ10DJ683T
CRJ10DJ623T
CRJ10DJ473T
CRJ10DJ0R0T
CRJ10DJ512T
CRJ10DJ104T
CRJ10DJ223T
CRJ10DJ683T
CRJ10DJ623T
CRJ10DJ753T
CRJ10DJ332T
CRJ10DJ512T
CRJ10DJ223T
CRJ10DJ683T
CRJ10DJ623T
CRJ10DJ273T
CRJ10DJ222T
CRJ10DJ512T
CCEA1HH4R7T
CCEA0JH102T
CCEA1EH101T
CCEA1EH101T
CWB1D01110058
CJP08GB142ZB
CJP07GI237ZW
CJP09GJ243ZW
CCEA1EH103E
CCEA1VH222EZ
CCEA1VH222EZ
CVIKIA278R15PI
CVIKIA7915PI
POWER PCB ASS'Y

C104
C105
C106
C107
C108
C109
C132
C133
C134
C921
C922
COP12365D
COIL , SMD POWER (10UH/3A) CMI-SPC9H45F-SERIES
KR3-50V4R7MA(5*11L)
1000UF 6.3V
KR3-25V101MB(6.3*11L)
KR3-25V101MB(6.3*11L)
WIRE ASS'Y
PIN HEADER (08P, 2.54mm) , ANGLE TYPE
LOCK-WAFER/STRAIGHT/2.5mm
LOCK-WAFER/ANGLE/2.5mm
CAP, ELECT(25V/10000uF)22x30 KR3-025V103MM300
CAP, ELECT (2200UF/35V, 12.5X31)KR3-35V222MH1-L/C4.0
CAP, ELECT (2200UF/35V, 12.5X31)KR3-35V222MH1-L/C4.0
I.C, REGULATOR(15V OUTPUT LOW DROP) KIA278R15PI
I.C, REGULATOR(-15V, TO-220AB) KIA7915PI
COP12394D
HCQI1H103JZT
HCQI1H103JZT
HCQI1H104JZT
HCQI1H103JZT
HCQI1H103JZT
HCQI1H104JZT
CCFT1H473ZF
CCFT1H473ZF
CCFT1H473ZF
KCME2E104JP04T
CCME2A104JXT
CAP , MYLAR
0.01UF 50V J
CAP , MYLAR
0.01UF 50V J
CAP , MYLAR
0.1UF 50V J
CAP , MYLAR
0.01UF 50V J
CAP , MYLAR
0.01UF 50V J
CAP , MYLAR
0.1UF 50V J
CAP , CERAMIC
0.047UF 50V Z
CAP , CERAMIC
0.047UF 50V Z
CAP , CERAMIC
0.047UF 50V Z
CAP , M-FILM (250V/0.1uF)
CAP,METAL-FILM(100V/0.1uF) HMFS104J2AP050T
100
AVR 2650
Reference
Designator
harman/kardon
Part Number
Description
POWER PCB ASS'Y

C923
C924
C925
D114
D115
D116
D117
D124
D125
D921
F110
F111
R901
R902
BN96
CN20
C135
D701
D991
RY21
R104
R105
BN90
BN92
RT01
TW91
CN12
F901
T901
WF104
WF105
COP12394D
CCME2A104JXT
HCQI1H473JZT
HCQI1H473JZT
CVD1N4003ST
CVD1N4003ST
CVD1N4003ST
CVD1N4003ST
CVD1N4003ST
CVD1N4003ST
CVD1N4003ST
KBA2D6300A2EYT
KBA2D6300A2EYT
C3A206
C3A206
CWB1D00912058
CJP05GA90ZY
CCEA1EH472E
CVDKBU804FMA
CMY1A219
CTB3+12JR
CVDGBJ1506BIA
CMY2A138
CTB3+8JR
HVDGBJ1506
CSL4B019ZU
CRQ1AJR47H
CRQ1AJR47H
CRE1A076
CTB3+6FFZR
CTB3+6JR
CTB3+8JFZR
CTS3+8JFZR
CTW3+12JR
CTW3+8JR
CUA4A294
KMC1A186
CSH1A015ZA
CSH1A015Z
CWB4F202080UK
CWZPM5003TW91A
CJJ8A006ZW
CWZPM5003TW91
CWC4C4A27B100B10
KBA2C8000TLEY
CLT5V058ZU
CWC4F2A17A100A10
CWC4F2A17A080A10
CAP,METAL-FILM(100V/0.1uF) HMFS104J2AP050T
CAP , MYLAR
0.047UF 50V J
CAP , MYLAR
0.047UF 50V J
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
DIODE , RECT
1N4003
FUSE(382 Series, 250V, 6.3A)
FUSE(382 Series, 250V, 6.3A)
WIRE , COPPER
SN95/PB5 , 0.6
WIRE , COPPER
SN95/PB5 , 0.6
WIRE ASS'Y (LOCKING TYPE, 2.5MM, 9PIN, 120MM)
WAFER , 5P(DIP, 3.96PITCH)
CAP , ELECT(25V/4700uF) KR3-25V472MR(16*31.5L)
BRIDGE DIODE ASS'Y
KBU804F
HEAT SINK (BRIDGE DIODE)
SCREW
DIODE HEAT SINK ASS'Y (CMY2A138)
HEAT SINK
SCREW
DIODE , BRIDGE(15A/600V)
GBJ1506
RELAY
GB-2C-D24P
RES , FUSE
RES , FUSE
SUPPORT , PCB
2.0
SCREW
11.0
SCREW
7.0
SCREW
19.0
SCREW
4.0
SCREW
2.0
SCREW
3.0
CHASSIS , BOTTOM
SECC 1.2T
SHIELD, CUSHION
2.0
SWITCH , MOMS WIRE ASS'Y (2P, 80MM, RED)
SWITCH , MOMS(OR-L-11G-BB)
OR-L-11G-BB
WIRE ASS'Y (3.96MM, 80MM, 2P, RED)
2P WIRE ASS'Y(100MM)
RECEPTACLE , AC(15A/250V,R-301,B21) R-301(B21)
2P WIRE ASS'Y(100MM)
CARD , CABLE (27p,1.25mm Pitch,100mm Protec
FUSE(218 Series, 250V, 8A)
TRANS , POWER(AVR2650)
CARD CABLE (1.0mm , A type , 17pin , 100mm)
CARD , CABLE (17P/1.00mm/80mm , A TYPE)
MISCELLANEOUS/MECHANICAL
CHE154
CGB1A233Z
CGL1A222
CLAMPER , ARM
BADGE , AVR2650
INDICATOR , VOLUME
101
AVR 2650
Reference
Designator
harman/kardon
Part Number
Description
MISCELLANEOUS/MECHANICAL
CGR1A530H63
CGU1A318Y
CGU2A410A25O
CGWAVR2650
CBT2A1064
CBT2A1065
CGB3A158Z
CGL1A265Y
CGW6A447RHUB24
CHG1A309
CMC1A372
CMC1A414
CMC1A416
CMC3A338
CMD1A555
CMD2A443
CMH2A215
CMZ1A127
COVER , USB
ORNAMENT , VOLUME
WINDOW , FIP
FRONT PANEL ASS'Y
KNOB , STANDBY
KNOB , BACK
BADGE , HARMAN/KARDON (FRONT)
INDICATOR , POWER
PANEL , FRONT
RUBBER
PLATE , SHIELD
PLTE , EARTH USB & HDMI
PLATE , EARTH TOP
PLATE , EARTH
BRACKET , SIDE (L)
BRACKET , SIDE
HOLDER , LED
FILTER , FIP
102
2.0
2.0
2.0
AVR 2650
harman/kardon
TECHNICAL DATA
Interface Transceiver of RS-232 Standard

with One Supply Voltage
ILX3232
DESCRIPTION
The ILX3232 is a 3V powered EIA/TIA-232 and V.28/V.24 communication interface with low power
requirements, high data-rate capabilities. ILX3232 has a proprietary low dropout transmitter output stage
providing true RS-232 performance from 3 to 5.5V supplies. The device requires only four small 0.1 F
standard external capacitors for operations from 3V supply.
The ILX3232 has two receivers and two drivers. The device is guaranteed to run at data rates of
250Kbps while maintaining RS-232 output levels. Typical applications are Notebook, Subnotebook and
Palmtop Computers, Battery Powered Equipment, Hand-Held Equipment, Peripherals and Printers.
FEATURES
300 A SUPPLY CURRENT
120Kbps MINIMUM GUARENTEED DATA RATE
3V/s MINIMUM GUARANTEED SLEW RATE
ENHANCED ESD SPECIFICATIONS:
15kV IEC1000-4-2 Air Discharge
AVAILABLE IN DIP-16, SO-16,TSSOP16 AND
SOP16L(W)
TSSOP 16
SOP16L(W)
Ordering Information
ILX3232N Plastic DIP
ILX3232D
SOIC
ILX3232TSD
TSSOP
ILX3232DW
SOP(W)
= from -40 to 85
for all packages
PIN CONFIGURATION
103
January 2009, Ver. 04
AVR 2650
harman/kardon
ILX3232
PIN DESCRIPTION
PlN N
SYMBOL
C1+
Positive Terminal for the first Charge Pump Capacitor
V+
C1
Doubled Voltage Terminal

Negative Terminal for the first Charge Pump Capacitor
C2+
C2
V-
T2OUT
R2IN
NAME AND FUNCTION
Positive Terminal for the second Charge Pump Capacitor

Negative Terminal for the second Charge Pump Capacitor
Inverted Voltage Terminal
Second Transmitter Output Voltage
Second Receiver Input Voltage
R2OUT
Second Receiver Output Voltage
10
T2IN
11
T1IN
Second Transmitter Input Voltage

First Transmitter Input Voltage
12
R1OUT
13
R1IN
14
T1OUT
15
GND
Ground
16
VCC
Supply Voltage
First Receiver Output Voltage

First Receiver Input Voltage
First Transmitter Output Voltage
ABSOLUTE MAXIMUM RATING

Symbol
Parameter
Value
Unit
-0.3 to 6
VCC
Supply Voltage
V+
Doubled Voltage Terminal
(VCC - 0.3) to 7
V-
Inverted Voltage Terminal
0.3 to -7
13
-0.3 to 6
V+ +|V-|
TIN
Transmitter Input Voltage Range
RIN
Receiver Input Voltage Range
TOUT
ROUT
tSHORT
25
-0.3 to (VCC + 0.3)
Transmitter Output Short to GND Time
13.2
Transmitter Output Voltage Range

Receiver Output Voltage Range
Continuous
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these
condition is not implied. V+ and V-can have a maximum magnitude of +7V, but their absolute addition can not exceed 13 V.
104
AVR 2650
harman/kardon
IDT74FCT38074
3.3V CMOS 1-TO-4 CLOCK DRIVER
INDUSTRIAL TEMPERATURE RANGE
3.3V CMOS
1-TO-4 CLOCK DRIVER
IDT74FCT38074
FEATURES:
DESCRIPTION:
The FCT38074 is a 3.3V clock driver built using advanced CMOS

technology. This low skew clock driver offers 1:4 fanout. The large fanout from
a single input reduces loading on the preceding driver and provides an efficient
clock distribution network. Multiple power and grounds reduce noise. Typical
applications are clock and signal distribution.
Advanced CMOS Technology

Guaranteed low skew < 100ps (max.)
Very low duty cycle distortion< 250ps (max.)
High speed propagation delay< 3ns (max.)
Very low CMOS power levels
TTL compatible inputs and outputs
1:4 fanout
Maximum output rise and fall time < 1.5ns (max.)
Low input capacitance: 3pF typical
VCC = 3.3V 0.3V
Inputs can be driven from 3.3V or 5V components
Operating frequency up to 166MHz
Available in SOIC package
PIN CONFIGURATION
FUNCTIONAL BLOCK DIAGRAM
O1
VCC
O4
VCC
O3
IN
O2
GND
O1
O2
IN
O3
SOIC
TOP VIEW
O4
105
AVR 2650
harman/kardon
NJM2581
DUAL SUPPLY WIDE BAND 3ch VIDEO AMPLIFIER
s GENERAL DESCRIPTION
The NJM2581 is a dual supply voltage wide band 3ch
video amplifier. It is suitable for Y, Pb, and Pr signal because
frequency range is 50MHz.
The NJM2581 is suitable for Set Top Box, AV amplifier,
and other high quality AV systems.
s PACKAGE OUTLINE
NJM2581D
s FEATURES
q Operating Voltage
4.5 to 5.5V
q Wide frequency range
50MHz at 0dB typ.
q Internal 6dB Amplifier
q Internal 75Driver Circuit (2-system drive)
q Power Save Circuit
q Bipolar Technology
q Package Outline
DIP14, DMP14
s BLOCK DIAGRAM
VIN1
14
V+ 1
75
Driver
6dB
AMP
BIAS
VEE1
13
VOUT1
VIN2
12
V+ 2
75
Driver
6dB
AMP
BIAS
VEE2
11
VOUT2
VIN3
10
V+ 3
75
Driver
6dB
AMP
BIAS
VEE3
PowerSave
REF
Ver.7
106
VOUT3
GND
NJM2581M
AVR 2650
harman/kardon
SINGLE ISOLATION AMPLIFIER

NJM2505A is the single isolation amplifier developed by the
video signal. It can remove the noise of a signal with isolation amplifier
and carries in the small package (MTP5), it is suitable for the interface
of the video signal of a car AV system.
s PACKAGE OUTLINE
NJM2505AF
s FEATURES
q Operating Voltage 4.5 to 9.0V
q Input: Sync-tip Clamp
q Common Mode Noise Rejection Ratio 55dBtyp.
q Voltage Gain 0dBtyp.
q Frequency Characteristics 0dBtyp.at 10MHz
q Package MTP5
s PIN CONFIGURATION
1: Vout
2: GND
3: V+
4: Vin
5: VGND
s BLOCK DIAGRAM
VGND
GND
Vout
Vin
V+
NJM2505A
Ver.4
107
AVR 2650
harman/kardon
NJM2595
5-INPUT 3-OUTPUT VIDEO SWITCH

s PACKAGE OUTLINE
The NJM2595 is a 5-input 3-output video switch. Its switches

select one from five signals received from VTR,TV,DVD,
TV-GAME and others.
The NJM2595 is designed for audio items, such as AV amplifier
and others.
NJM2595D NJM2595M
s FEATURES
q 5-input 3-output
q Operating Voltage
4.0 to 6.5V
q Operating current
15mAtyp. at Vcc=5V
q Crosstalk
-65dBtyp.
q Internal 6dB Amplifier
q Internal 75 Driver
q Package Outline
DIP16,DMP16
s PIN CONFIGURATION and BLOCK DIAGRAM
+
SW1 SW5
SW2
16
10
14
Vin1 13
Vin2
S5
S1
6dB
Amp
Vin3
Vin4
Vin5
20k
Vout1
75
Driver
15
Vout2
6dB
Amp
20k
75
Driver
11
Vout3
20k
S2
75
Driver
6dB
Amp
20k
S6
S4
S3
20k
20k
S7
20k
SW3
12
SW4
GND
108
V-
AVR 2650
harman/kardon
NJW1321
WIDE BAND VIDEO SWITCH WITH I2C BUS
2
The NJW1321 is a Wide Band Video Switch with I C BUS.
The NJW1321 includes switch of 4-input 2-output and 6dB
amplifier. It is suitable for RGB or Y, Pb, and Pr signal because
frequency range is 100MHz.
The NJW1321 includes external logic control terminals and
external logic discernment terminals.
The NJW1321 is suitable for PTV, DTV, PDP and other high quality
AV systems.
s FEATURES
q Operating Voltage
2
q I C BUS Interface
q 4-input 2-output 3-Circuits
q Wide frequency range
s PACKAGE OUTLINE
NJW1321FP1
+9.0V
0dB at 100MHz typ.

-3dB at 300MHz typ.
q Internal 6dB amplifier (Selectable Bypass or 6dB)
q External logic discernment terminal
q External logic control terminal
q Selectable slave address
q Power Save Circuit
q Bi-CMOS Technology
q Package Outline
QFP48
s BLOCK DIAGRAM
Y/R IN1
6dB
Y/R OUT1
6dB
Y/R OUT2
6dB
Pb/G OUT1
6dB
Pb/G OUT2
6dB
Pr/B OUT1
6dB
Y/R IN2
Pr/B OUT2
Y/R IN3
Y/R IN4
Pb/G IN1
Pb/G IN2
Pb/G IN3
Pb/G IN4
Pr/B IN1
Pr/B IN2
Pr/B IN3
Pr/B IN4
PORT 0
ADDRESS
PORT 1
SDA
PORT 2
SCL
I2C BUS
PORT 3
GND
AUX 0
AUX 1
V+
AUX 2
BIAS
AUX 3
VREF
DGND
Ver.3
109
AVR 2650
harman/kardon
NJW1321
Pb IN4
V+
Y IN4
V+
Y OUT1
GND
Pb OUT1
GND
Pr OUT1
AUX3
AUX2
Y OUT2
AUX1
AUX0
sPIN CONFIGURATION
38
24
48
15
1
14
Pb IN2
GND
Pr IN2
GND
Y IN1
V+
Pb IN1
V+
Pr IN1
GND
PORT3
PORT2
ADR
39
V+
GND
Pr IN4
V+
Y IN3
GND
Pb IN3
V+
Pr IN3
GND
Y IN2
25
1. V+
13. PORT2
25. AUX0
37. V+
2. Pb IN2
14. ADR
26. AUX1
38. Pb IN4
3. GND
15. SCL
27. Y OUT2
39. GND
4. Pr IN2
16. SDA
28. AUX2
40. Pr IN4
5. GND
17. GND
29. AUX3
41. V+
6. Y IN1
18. DGND
30. Pr OUT1
42. Y IN3
7. V+
19. VREG
31. GND
43. GND
8. Pb IN1
20. V+
32. Pb OUT1
44. Pb IN3
9. V+
21. Pr OUT2
33. GND
45. V+
10. Pr IN1
22. PORT1
34. Y OUT1
46. Pr IN3
11. GND
23. PORT 0
35. V+
47. GND
12. PORT3
24. Pb OUT2
36. Y IN4
48. Y IN2
110
Pb OUT2
PORT0
PORT1
Pr OUT2
V+
VREF
DGND
GND
SDA
SCL
AVR 2650
harman/kardon
SI-8005Q
Step-Down Switching Regulator with Current-Mode Control
Features and Benefits
Description
Current-mode control system employed

Excellent line regulation (60 mV maximum)
165 m maximum on-resistance of built-in MOSFET
Output current 3.5 A
Wide range of input voltages (4.75 to 28 V), supports 24
V direct drive
Output voltage 0.5 to 24 V, compatible with various IC
power supply voltages, through low VREF of 0.5 V.
High efficiency, 94% maximum at VIN = 8 V, VO = 5 V,
and IO = 0.5 A
Operating frequency 500 kHz, supports downsizing of
smoothing choke coil
Soft start and output on/off functions built-in
Built-in protection:
Drooping overcurrent protection
Overtemperature protection
Undervoltage lockout (UVLO)
The SI-8005Q is a step-down switching regulator IC, designed as

an output voltage regulator at the secondary stage of switch mode
power supplies. The current-mode control system permits small
ceramic capacitors to be used as output capacitors. Together
with the compact HSOP8 package, this allows reduction of
regulator circuitry area on the PCB by approximately 50% in
comparison with conventional topologies.
Designed to save power, losses in the SI-8005Q are reduced
by controlling the maximum on-resistance of a built-in output
MOSFET to as low as 165 m. Furthermore, die miniaturization
has been accomplished through a proprietary BCD process.
The SI-8005Q supplies an output current of 3.5 A and an output
voltage that is variable from 0.5 to 24 V, which is easily set to
a voltage compatible with the diverse reduced power supply
voltages required by signal processing ICs. Accepting a wide
input voltage range, from 4.75 to 28 V, the SI-8005Q can be
driven directly by a 24 V power supply.
Package: HSOP8 surface mount with

exposed thermal pad
Applications include power supplies for signal processing ICs

for memories and microcomputers used in plasma display panel
(PDP) TVs, liquid crystal display (LCD) TVs, computer hard
drives, and DVD recorders.
Not to scale
Functional Block Diagram
111
AVR 2650
harman/kardon
Philips Semiconductors
Product specification
20-bit buffer/line driver, non-inverting (3-State)
PIN CONFIGURATION
74ALVCH16827
LOGIC SYMBOL (IEEE/IEC)
1OE1
56
1Y0
55
1OE1
1OE2
1A0
1Y1
54
53
GND
1Y2
52
1A2
1Y3
51
1A3
VCC
1Y4
50
49
1Y5
48
2OE2
10
47
46
11
EN2
55
1Y0
1Y1
52
1Y2
51
1Y3
49
1Y4
48
1Y5
47
10
1Y6
45
12
1Y7
44
13
1A9
43
14
1Y9
2A0
42
15
2Y0
2A1
41
16
2Y1
2A2
40
17
2Y2
1A1
VCC
1A2
1A4
1A3
1A5
1A6
1A5
GND
&
29
54
1A0
1A4
1Y6
EN1
56
2OE1 28
1A1
GND
1OE2
&
GND
1A6
1Y7
12
45
1A7
1Y8
13
44
1A8
1Y9
14
43
1A9
2Y0
15
42
2A0
2Y1
16
41
2A1
2Y2
17
40
2A2
GND
18
39
GND
2A3
38
19
2Y3
2Y3
19
38
2A3
2A4
37
20
2Y4
2Y4
20
37
2A4
2A5
36
21
2Y5
21
36
2A5
2A6
34
23
2Y6
VCC
22
35
VCC
2A7
33
24
2Y7
2Y6
23
34
2A6
2A8
31
26
2Y8
2Y7
24
33
2A7
2A9
30
27
2Y9
GND
25
32
GND
2Y8
26
31
2A8
2Y9
27
30
2A9
2OE1
28
29
2OE2
1A7
1A8
1Y8
2Y5
SH00012
SH00010
LOGIC SYMBOL
55
54
52
51
49
48
47
45
44
FUNCTION TABLE
43
INPUTS
1A0 1A1 1A2 1A3 1A4 1A5 1A6
1A7 1A8
1A9
OUTPUTS
nOE2
1OE1
56
nOE1
1OE2
1Y0 1Y1 1Y2 1Y3 1Y4 1Y5 1Y6
2
42
3
41
5
40
6
38
8
37
9
36
10
34
2A0 2A1 2A2 2A3 2A4 2A5 2A6
1Y7 1Y8
12
33
13
31
1Y9
14
H
L
X
Z
30
2A7 2A8
2A9
2Y0 2Y1 2Y2 2Y3 2Y4 2Y5 2Y6
2Y7 2Y8
2Y9
15
24
27
28
2OE1
29
2OE2
16
17
19
20
21
23
26
SH00011
112
=
=
=
=
X
H
High voltage level
Low voltage level
Dont care
High impedance off state
AVR 2650
harman/kardon
Philips Semiconductors
Product specification
20-bit buffer/line driver, non-inverting (3-State)
74ALVCH16827
LOGIC DIAGRAM
nA0
nA1
nA2
nA3
nA4
nA5
nA6
nA7
nA8
nA9
nY0
nY1
nY2
nY3
nY4
nY5
nY6
nY7
nY8
nY9
nOE1
nOE2
SH00013
RECOMMENDED OPERATING CONDITIONS

SYMBOL
MIN
MAX
DC supply voltage 2.5V range (for max. speed

performance @ 30 pF output load)
VCC
PARAMETER
CONDITIONS
2.3
2.7
DC supply voltage 3.3V range (for max. speed

performance @ 50 pF output load)
3.0
UNIT
3.6
VI
DC Input voltage range
VCC
VO
DC output voltage range
VCC
40
+85
0
0
20
10
ns/V
Tamb
Operating free-air temperature range
tr, tf
Input rise and fall times
VCC = 2.3 to 3.0V

VCC = 3.0 to 3.6V
ABSOLUTE MAXIMUM RATINGS1

In accordance with the Absolute Maximum Rating System (IEC 134)
Voltages are referenced to GND (ground = 0V)
SYMBOL
VCC
IIK
PARAMETER
CONDITIONS
DC input diode current
50
VI t0
UNIT
0.5 to +4.6
DC supply voltage
RATING
mA
For control pins2
0.5 to +4.6
For data inputs2
0.5 to VCC +0.5
VI
DC in ut voltage
input
IOK
DC output diode current
VO uVCC or VO t 0
VO
DC output voltage
Note 2
IO
DC output source or sink current
VO = 0 to VCC
IGND, ICC
Tstg
PTOT
"50
mA
0.5 to VCC +0.5
For temperature range: 40 to +125 C

above +55C derate linearly with 11.3 mW/K
above +55C derate linearly with 8 mW/K
mA
mA
65 to +150
Storage temperature range
"50
"100
DC VCC or GND current
Power dissipation per package

plastic medium-shrink (SSOP)
plastic thin-medium-shrink (TSSOP)
850
600
mW
NOTE:
1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the
device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to
absolute-maximum-rated conditions for extended periods may affect device reliability.
2. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
113
AVR 2650
harman/kardon
MX29LV320D T/B
32M-BIT [4M x 8 / 2M x 16] 3V SUPPLY FLASH MEMORY
FEATURES
GENERAL FEATURES
Byte/Word switchable
- 4,194,304 x 8 / 2,097,152 x 16
Sector Structure
- 8K-Byte x 8 and 64K-Byte x 63
Extra 64K-Byte sector for security
- Features factory locked and identifiable, and customer lockable
Twenty-Four Sector Groups
- Provides sector group protect function to prevent program or erase operation in the protected sector group
- Provides chip unprotect function to allow code changing
- Provides temporary sector group unprotect function for code changing in previously protected sector groups
Power Supply Operation
- Vcc 2.7 to 3.6 volt for read, erase, and program operations
Latch-up protected to 100mA from -1V to 1.5 x Vcc
Low Vcc write inhibit : Vcc <= Vlko
Compatible with JEDEC standard
- Pinout and software compatible to single power supply Flash
Functional compatible with MX29LV320C T/B device
PERFORMANCE
High Performance
- Fast access time: 70ns
- Fast program time: 11us/word typical utilizing accelerate function
- Fast erase time: 0.7s/sector, 35s/chip (typical)
Low Power Consumption
- Low active read current: 10mA (typical) at 5MHz
- Low standby current: 5uA (typical)
Typical 100,000 erase/program cycle
10 years data retention
SOFTWARE FEATURES
Erase Suspend/ Erase Resume
- Suspends sector erase operation to read data from or program data to another sector which is not being erased
Status Reply
- Data# Polling & Toggle bits provide detection of program and erase operation completion
Support Common Flash Interface (CFI)
HARDWARE FEATURES
Ready/Busy# (RY/BY#) Output
- Provides a hardware method of detecting program and erase operation completion
Hardware Reset (RESET#) Input
- Provides a hardware method to reset the internal state machine to read mode
WP#/ACC input pin
- Provides accelerated program capability
P/N:PM1281
REV. 1.0, AUG. 14, 2008
114
AVR 2650
harman/kardon
MX29LV320D T/B
PIN CONFIGURATION
48 TSOP
44 SOP
WE#
A18
A17
A7
A6
A5
A4
A3
A2
A1
A0
CE#
GND
OE#
Q0
Q8
Q1
Q9
Q2
Q10
Q3
Q11
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
A15
A14
A13
A12
A11
A10
A9
A8
A19
A20
WE#
RESET#
NC
WP#/ACC
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
A20
A19
A8
A9
A10
A11
A12
A13
A14
A15
A16
BYTE#
GND
Q15/A-1
Q7
Q14
Q6
Q13
Q5
Q12
Q4
VCC
A16
BYTE#
GND
Q15/A-1
Q7
Q14
Q6
Q13
Q5
Q12
Q4
VCC
Q11
Q3
Q10
Q2
Q9
Q1
Q8
Q0
OE#
GND
CE#
A0
48-Ball TFBGA/LFBGA (6mm x 8mm, Top View, Balls Facing Down)
A13
A12
A14
A15
A16
BYTE#
Q15/
A-1
GND
A9
A8
A10
A11
Q7
Q14
Q13
Q6
WE#
RESET#
NC
A19
Q5
Q12
VCC
Q4
RY/BY#
WP#/
ACC
A18
A20
Q2
Q10
Q11
Q3
A7
A17
A6
A5
Q0
Q8
Q9
Q1
A3
A4
A2
A1
A0
CE#
OE#
GND
1
A
P/N:PM1281
REV. 1.0, AUG. 14, 2008
115
AVR 2650
harman/kardon
116
AVR 2650
harman/kardon
117
AVR 2650
harman/kardon
FLI30336
Single-chip enhanced LCD TV controller
Data Brief
Features
Applications
Integrated 3D video decoder
LCD and PDP TV
Flexible digital capture up to 165 MHz and

analog capture up to 162 MHz
DLP, LCD, and LCOS front and rear

projection
VBI signal processing including WST version

2.5 support
Flexible DDR memory interface
Faroudja TrueLife video enhancer
Advanced Picture-in-Picture (PIP) features
Advanced Color Management (ACM-3D) and

Adaptive Contrast Control (ACC)
On-chip microprocessor
Advanced bitmapped OSD controller
LCD overdrive
Embedded 10-bit dual-channel LVDS for

1080p and WUXGA panel support
Package: 416 PBGA

External Memory
10-bit Triple
ADC
YPrPb/
RGB 2
2x24-bit or
1x30+1x16 bit
input
OSD
Blend
10 bit
LVDS Tx
CLUTs
YPrPb/
RGB 1
10-bit 3D Video
Decoder and
Triple ADC
Sharpening
Filters
ACM 3D
and ACC
Analog
Front
End
OSD
Controller
Output
Formatter
Dual
Channel
LVDS
TTL
RGB or
YUV
MUX
YC2
10 bit
Memory
Controller
Picture
Blend
YC1
3x3
Matrix
TTX
Decoder
Enhancer
VBI Data
Proc
Digital
Input
Port
DCDi Format
Conversion
for PIP
IR I/
F
Embedded
Micro processor
3x3
Matrix
CV1
CV2
CV3
LBWADC
Control Interface 6 channels
General
Purpose
I/O
GPIO
Audio
Delay
I2S
in
I2S
out
www.st.com
118
AVR 2650
harman/kardon
Description
FLI30336
Description
The FLI30336 offers high integration for advanced applications of Picture-in-Picture (PIP)
and Picture-by-Picture (PBP) with an integrated video decoder and a 3D comb filter. The
FLI30336 can power up to 1080p/WUXGA displays with the proven Faroudja DCDi Cinema
branded technology.
Special performance features such as the Faroudja DCDi Cinema video format converter,
10-bit performance in the device, and the Advanced Color Management (ACM-3D) provide
exceptional video quality. This exclusive level of video quality technology only seen on
Faroudja Home Theater Systems is now available in a single-chip solution.
The FLI30336 also comprises an integrated Analog Front-End (AFE) that includes triple
ADCs and an integrated cross-point switch. The flexible AFE ensures simple PCB design
with direct connections to TV tuners and input video connectors. In essence, the FLI30336
is the only device needed for a single LCD TV chassis supporting worldwide standards. For
regional variations, only connector and firmware changes are required.
The integrated VBI dataslicer and decoder remove the need for external components
resulting in significant cost reduction. The FLI30336 supports many worldwide VBI
standards for applications of Teletext, Closed Captioning, V-Chip, and other VBI services.
The FLI30336 can be used in digital TV solutions requiring Faroudja DCDi Cinema video
performance levels. An embedded microprocessor and a versatile OSD in a single device
will facilitate rapid development of a reliable and attractive product. The FLI30336 utilizes
the common Cortez family firmware for easy and effortless migration across different
hardware platforms within this family.
Figure 1.
System diagram
DDR
SDRAM
RF
TV
Tuner
Component Video
SCART or Analog RGB
Y/C
RF
16 configurable
analog inputs
FLI30336
Optional Second
Analog Channel
MPEG-2 Decoder
Program
Flash
2/7
119
LVDS
Display
up to
WUXGA/
1080p
AVR 2650
harman/kardon
A3S56D30FTP
A3S56D40FTP
256M Double Data Rate Synchronous DRAM
Pin Assignment (Top View) 66-pin TSOP
x8
x16
Vdd
DQ0
VddQ
NC
DQ1
VssQ
NC
DQ2
VddQ
NC
DQ3
VssQ
NC
NC
VddQ
NC
NC
Vdd
NC
NC
/WE
/CAS
/RAS
/CS
NC
BA0
BA1
A10/AP
A0
A1
A2
A3
Vdd
Vdd
DQ0
VddQ
DQ1
DQ2
VssQ
DQ3
DQ4
VddQ
DQ5
DQ6
VssQ
DQ7
NC
VddQ
LDQS
NC
Vdd
NC
LDM
/WE
/CAS
/RAS
/CS
NC
BA0
BA1
A10/AP
A0
A1
A2
A3
Vdd
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
66pin TSOP(II)
400mil width
x
875mil length
0.65mm
Lead Pitch
Row
A0-12
Column
A0-9 (x8)
A0-8 (x16)
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
Vss
DQ15
VssQ
DQ14
DQ13
VddQ
DQ12
DQ11
VssQ
DQ10
DQ9
VddQ
DQ8
NC
VssQ
UDQS
NC
VREF
Vss
UDM
/CLK
CLK
CKE
NC
A12
A11
A9
A8
A7
A6
A5
A4
Vss
Vss
DQ7
VssQ
NC
DQ6
VddQ
NC
DQ5
VssQ
NC
DQ4
VddQ
NC
NC
VssQ
DQS
NC
VREF
Vss
DM
/CLK
CLK
CKE
NC
A12
A11
A9
A8
A7
A6
A5
A4
Vss
CLK, /CLK
CKE
/CS
/RAS
/CAS
/WE
: Master Clock
: Clock Enable
: Chip Select
: Row Address Strobe
: Column Address Strobe
: Write Enable
A0-12
BA0,1
Vdd
VddQ
Vss
VssQ
: Address Input
: Bank Address Input
: Power Supply
: Power Supply for Output
: Ground
: Ground for Output
DQ0-15
DQ0-7
UDM, LDM
DM
UDQS, LDQS
DQS
: Data I/O (x16)

: Data I/O (x8)
: Write Mask (x16)
: Write Mask (x8)
: Data Strobe (x16)
: Data Strobe (x8)
VREF
: SSTL_2 reference voltage
120
AVR 2650
harman/kardon
A3S56D30FTP
A3S56D40FTP
256M Double Data Rate Synchronous DRAM
PIN FUNCTION
SYMBOL
TYPE
DESCRIPTION
Input
Clock: CLK and /CLK are differential clock inputs. All address and control
input signals are sampled on the crossing of the positive edge of CLK and
negative edge of /CLK. Output (read) data is referenced to the crossings of
CLK and /CLK (both directions of crossing).
CKE
Input
Clock Enable: CKE controls Power Down and Self Refresh.

Taking CKE LOW provides Precharge Power Down or Self Refresh (all banks idle),
or Active Power Down (row active in any bank).
Taking CKE HIGH provides Power Down exit or Self Refresh exit.
After Self Refresh is started, CKE becomes asynchronous input.
Power Down and Self Refresh is maintained as long as CKE is LOW.
/CS
Input
Chip Select: When /CS is HIGH, any command means No Operation.
/RAS, /CAS, /WE
Input
Combination of /RAS, /CAS, /WE defines basic commands.
A0-12
Input
A0-12 specify the Row / Column Address in conjunction with BA0,1. The
Row Address is specified by A0-12. The Column Address is specified by
A0-9(x8) and A0-8(x16). A10 is also used to indicate precharge
option. When A10 is HIGH at a Read / Write command, an Auto Precharge
is performed. When A10 is HIGH at a Precharge command, all banks are precharged.
BA0,1
Input
Bank Address: BA0,1 specifies one of four banks to which a command is applied.
BA0,1 must be set with Active, Precharge, Read, Write commands.
CLK, /CLK
DQ0-7 (x8),
DQ0-15 (x16),
DQS (x8)
Input / Output
Data Input/Output: Data bus
Input / Output
Data Strobe: Output with read data, input with write data. Edge-aligned
with read data, centered in write data. Used to capture write data.
For the x16, LDQS corresponds to the data on DQ0-DQ7; UDQS
correspond to the data on DQ8-DQ15
UDQS, LDQS (x16)
Input Data Mask: DM is an input mask signal for write data. Input data
is masked when DM is sampled HIGH along with that input data
during a write access. DM is sampled on both edges of DQS.
Although DM pins are input only, the DM loading matches the DQ
and DQS loading. For the x16, LDM corresponds to the data on DQ0-DQ7;
UDM corresponds to the data on DQ8-DQ15.
DM (x8)
UDM, LDM (x16)
Input
Vdd, Vss
Power Supply
Power Supply for the memory array and peripheral circuitry.
VddQ, VssQ
Power Supply
VddQ and VssQ are supplied to DQ, DQS buffers.
VREF
Input
SSTL_2 reference voltage.
121
AVR 2650
harman/kardon
12-Bit, 170 MHz Video and Graphics Digitizer with

3D Comb Filter Decoder and
Quad HDMI 1.4 Fast Switching Receiver
ADV7844
PRELIMINARY
FEATURES
Supports up to 5 SPDIF outputs,

Supports up to 4 I2S outputs
General
Highly flexible 36-bit pixel output interface
Internal EDID RAM for HDMI and graphics
Dual STDI (standard identification) function support
Any-to-any, 3 3 color space conversion (CSC) matrix
2 programmable interrupt request output pins
Simultaneous analog processing and HDMI monitoring
Quad HDMI 1.4 Fast Switching Receiver

170 MHz Video and Graphics Digitizer
3D Comb Filter Video Decoder
SCART Fast Blank Support
Adaptive HDMI Equaliser
Integrated CEC Controller
HDMI Repeater Support
Advanced VBI data slicer
APPLICATIONS
Video and Graphics Digitizer
Four 170 MHz, 12-bit ADCs,
12-channel analog input mux
525i-/625i-component analog input
525p-/625p-component progressive scan support
720p-/1080i-/1080p-component HDTV support
Low refresh rates (24/25/30 Hz) support for 720p/1080p
Digitizes RGB graphics up to 1600 1200 at 60 Hz (UXGA)
3D Video Decoder
NTSC/PAL/SECAM color standards support
NTSC/PAL 2D/3D motion detecting comb filter
Advanced time-base correction (TBC) with frame
synchronization
Interlaced-to-progressive conversion for 525i and 625i
IF compensation filters
Vertical peaking and horizontal peaking filters
Robust synchronization extraction for poor video source
4:1 HDMI 1.4 225 MHz Receiver
Fast-Switching of HDMI ports
2:2 HEAC muxing support
2 HEAC channel support
2 Ethernet Interfaces for HEC Support
SPDIF interface for ARC support.
3D Video format support including frame packing 1080p
24Hz, 720p 50 Hz, 720p 60Hz
Full colorimetry support including sYCC601, Adobe RGB,
Adobe YCC 601
36-/30-bit Deep Color and 24-bit color support
HDCP 1.3 support with internal HDCP Keys
+5V Detect and Hot plug assert for each HDMI port
Full HDMI Audio Support including HBR, DSD, DST
Advanced Audio mute feature
Flexible digital audio output interfaces
Advanced TVs
PDP HDTVs
LCD TVs (HDTV ready)
LCD/DLP rear projection HDTVs
CRT HDTVs
LCoS HDTVs
AVR video receivers
LCD/DLP front projectors
HDTV STBs with PVR
Projectors

SDRAM
CVBS
ADC
CVBS
ADC
YC
SD/PS
YPbPr
INPUT MUX
SCART RGB
+ CVBS
ADC
ADC
48
CVBS
HS/VS
SDP
SCART G CVBS 3D YC
S-VIDEO
SCART B
CLK
SCART
DATA
SCART R
HS/VS
CP
Y/G
YPbPr
Pb/B 525p/625p
720p/1080i
1080p/UXGA
Pr/R
RGB
HD YPbPr
GRAPHICS
RGB
FIELD/DE
HS/VS
OUTPUT MUX
SCART
CVBS
FIELD/DE
FIELD/DE
CLK
36-BIT YCbCr
/RGB
CLK
DATA
36
HDMI 2
TMDS
DDC
TMDS
DDC
HDMI 3
TMDS
DDC
HDMI 4
TMDS
DDC
SPDIF
ETHERNET 1
DSD
HBR
MCLK
FAST
SWITCH
HDCP
KEYS
AUDIO
OUTPUT
MCLK
SCLK
SCLK
TO AUDIO
PROCESSOR
HEAC
ETHERNET 2
ADV7844
Figure 1.
122
I2 S
SPDIF
DEEP
COLOR
HDMI Rx
OUTPUT MUX
HDMI 1
AVR 2650
harman/kardon
ADV7844
PRELIMINARY
DETAILED FUNCTIONAL BLOCK DIAGRAM

ANALOG FRONT END
STANDARD DEFINITION PROCESSOR (SDP)
AOUT
CLAMP
CLAMP
12-CHANNEL
YPrPb
INPUT
MATRIX
CLAMP
RGB
SYNC1
SYNC2
HS_IN1
VS_IN1
HS_IN2/TRI5
VS_IN2/TRI6
ADC2
ADC3
12
DECIMATION
FILTERS
MACROVISION
DETECTION
CO LO R SP AC E
CO NVE RSIO N
INTERLACE
TO PROGRESSIVE
CONVERSION
FASTBLANK
OVERLAY
CONTROL
12
HS/CS,VS/FIELD
DIGITAL PROCESSING BLOCK
LLC GENERATION
CONTROL
COMPONENT PROCESSOR
AVLINK
CEC
RXA_5V / HPDA
RXB_5V / HPDB
RXC_5V / HPDC
RXD_5V / HPDD
DDCA_SDA / DDCA_SCL
DDCB_SDA / DDCB_SCL
DDCC_SDA / DDCC_SCL
DDCD_SDA / DDCD_SCL
RXA_C
RXB_C
RXC_C
RXD_C
RXA_0
RXA_1
RXA_2
RXB_0
RXB_1
RXB_2
CONTROL
AND DATA
I2C CONTROL INTERFACE

AVLINK
CONTROLLER
MUX
TRI-LEVEL
SLICER
PROGRAMMABLE
DELAY
5V DETECT AND HPD

CONTROLLER
HDCP
EEPROM
4:2:2 TO 4:4:4
CONVERSION
EQUALIZER
SAMPLER
EQUALIZER
SAMPLER
RXC_0
RXC_1
RXC_2
EQUALIZER
SAMPLER
RXD_0
RXD_1
RXD_2
EQUALIZER
ANCILLARY
DATA
FORMATTER
I2C
READBACK
SAMPLER
HEAC_1
HEAC_2
SPDIF_IN
E1_TX/E1_RX
E2_TX/E2_RX
DIGITAL
FINE CLAMP
GAIN
CONTROL
12
P0 TO P11
12
P12 TO P23
12
P24 TO P35
LLC
HS/CS
VS/FIELD
DE
SYNC_OUT
OFFSET
ADDER
ACTIVE PEAK
AND HSYNC DEPTH
DEEP COLOR
CONVERSION
HDCP
BLOCK
AV
CODE
INSERTION
CP CSC AND
DECIMATION
FILTERS
NOISE AND
CALIBRATION
VSI
DECODER
PLL
STANDARD
IDENTIFICATION
MACROVISION
AND CGMS DETECTION
(A)
(B)
(C)
CEC CONTROLLER
EDID/
REPEATER
CONTROLLER
SYNC EXTRACT
(ESDP)
SYNC SOURCE
AND POLARITY
DETECT
FASTSWITCHING
BLOCK + HDMI DECODE
+ MUX
SCL
SDA
DDR/SDR-SDRAM INTERFACE
STANDARD
AUTODECTION
SYNC PROCESSING
AND CLOCK GENERATION
TRI1 TO
TRI4
3D COMB
HORIZONTAL
PEAKING
(A)
(B)
(C)
(D)
ADC1
CLAMP
TBC
VERTICAL
PEAKING
CTI and LTI
12
YC
SCART RGB
ADC0
FILTER
PACKET/
INFOFRAME
MEMORY
FAST I2C
INTERFACE
TTX_SDA / TTX_SCL
VIDEO DATA PROCESSOR
PACKET
PROCESSOR
AUDIO
PROCESSOR
HDMI ETHERNET CHANNEL

&
AUDIO RETURN CHANNEL
Figure 2. Detailed Functional Block Diagram
123
Rev. PrC| Page 4 of 35
INT1
INT2
INTERRUPT
CONTROLLER
AUDIO OUTPUT FORMATTER
CVBS
2D COMB
VIDEO OUTPUT FORMATTER
12
AP0
AP1
AP2
AP3
AP4
AP5
SCLK
MCLK
AVR 2650
harman/kardon
ADV7844
PRELIMINARY
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
GND
VS/FIELD
E2_TX+
E2_RX+
TVDD
RXD_2-
RXD_1-
RXD_0-
RXD_C-
HEAC_2 -
TVDD
RXC_2-
RXC_1-
RXC_0-
RXC_C-
NC
TVDD
RXB_2-
RXB_1-
RXB_0-
RXB_C-
HEAC_1 -
GND
HS/CS
FIELD/DE
E2_TX-
E2_RX-
TVDD
RXD_2+
RXD_1+
RXD_0+
RXD_C+
HEAC_2+
TVDD
RXC_2+
RXC_1+
RXC_0+
RXC_C+
NC
TVDD
RXB_2+
RXB_1+
RXB_0+
RXB_C+
HEAC_1 +
GND
P0
P1
E1_TX+
E1_RX+
TVDD
PWRDN1 PWRDN2
HPA_D
RXD_5V
RXC_5V
TVDD
GND
GND
GND
GND
GND
GND
TVDD
TVDD
TVDD
TVDD
TVDD
TVDD
P2
P3
E1_TX-
E1_RX-
TVDD
HPA_C
RXB_5V
HPA_B
TVDD
RXA_5V
HPA_A
D D C B _SD A D D C B_SC L
TVDD
RXA_2+
RXA_2-
DVDDIO
DVDDIO
GND
GND
DDCA_SDA
CVDD
RXA_1+
RXA_1-
P5
P4
DDCA_SCL
CVDD
RXA_0+
RXA_0-
P7
P6
P9
P8
P 11
P10
MCLK
P 13
P12
DVDDIO
S YN C _O U T
CEC
D D C D _S D A D D C D _ S C L D D C C _S D A D D C C _ S C L
RTERM
EP_MISO EP_MOSI
EP_SCK
GND
GND
GND
GND
TEST1
TEST2
GN D
GND
CVDD
CVDD
CVDD
VGA_SCL
CVDD
RXA_C+
RXA_C-
TTX_SDA TTX_SCL
GND
GND
GND
GND
GND
GND
GN D
GND
CVDD
CVDD
CVDD
VGA_SDA
CVDD
NC
NC
AP0
GND
GND
GND
GND
GND
GND
GN D
GND
GN D
GND
GND
PVDD
TE S T3
GN D
GND
AP5
SCLK
VDD
GND
GND
GND
GND
GND
GN D
GND
GN D
GND
GND
PVDD
GND
XTALN
XTALP
DVDDIO
GND
GN D
VDD
GND
GND
GND
GND
GND
GN D
GND
GN D
GND
GND
GN D
GND
GN D
GND
P 15
P14
AP4
AP3
VDD
GND
GND
GND
GND
GND
GN D
GND
GN D
GND
GND
GN D
GND
REFN
REFP
P 17
P16
AP2
AP1
VDD
GND
GND
GND
GND
GND
GN D
GND
GN D
GND
GND
AVDD
AVDD
AVDD
AVDD
P 18
P19
SCL
SDA
VDD
GND
GND
GND
GND
GND
GN D
GND
GN D
GND
GND
AVDD
AVDD
AIN11
AIN12
P 20
P21
TEST4
INT1
VDD
GND
GND
GND
GND
GND
GN D
GND
GN D
GND
GND
SYNC4
AIN10
P 22
P23
TEST5
INT2
VDD
GND
GND
GND
GND
GND
GN D
GND
GN D
GND
GND
GN D
GND
GN D
GND
DVDDIO
DVDDIO
DVDDIO
DVDDIO
VDD
VDD
VDD
VDD
VDD
VDD
VD D
VDD
GN D
GN D
GND
TRI4
TRI3
AIN9
AIN8
LLC
P24
RESET
AVLINK
TRI1
TRI2
SYNC3
AIN7
P25
P26
NC
SPDIF_IN
AVDD
AVDD
AVDD
AVDD
P27
P28
GND
GND
GND
VDD_SDRAM SDRAM _A11 S D R A M _ A 6 S D R A M _ A 2 S D R A M _C S SDRAM_LDQS
GND
SDRAM_DQ6 SDRAM_DQ2 SDRAM_DQ15 SDRAM_DQ11 SDRAM_CKE VDD_SDRAM
GND
AOUT
NC
AIN5
AIN6
AA
P29
P30
GND
GND
GND
VDD_SDRAM S D R A M _ A 9 S D R A M _ A 5 S D R A M _ A 1 SDRAM_RAS SDRAM_DQ7
GND
SDRAM_DQ5 SDRAM_DQ1 SDRAM_DQ12 SDRAM_DQ8 S D R A M _ C K VDD_SDRAM
GND
NC
NC
SYNC2
AIN4
AA
AB
P31
P32
P34
NC
GND
DVDDIO
S D R A M _ A 8 S D R A M _ A 4 S D R A M _ A 0 SDRAM_BA1 SDRAM_CAS VDD_SDRAM SDRAM_DQ4 SDRAM_DQ0 SDRAM_DQ13 SDRAM_DQ9 SDRAM_CKN VDD_SDRAM
GND
SYNC1
GND
AB
AC
GND
P33
P35
NC
GND
DVDDIO
S D R A M _ A 7 S D R A M _ A 3 SDRAM _A10 SDRAM_BA0 SDRAM_W E VDD_SDRAM SDRAM_DQ3 SDRAM_VREF SDRAM_DQ14 SDRAM_DQ10 SDRAM_UDQS VDD_SDRAM
GND
AIN1
AIN2
AIN3
GND
AC
19
20
21
22
23
EP_CS
10
11
12
13
14
Figure 7. Pin Configuration
124
Rev. PrBC | Page 12 of 35
15
16
17
HS_IN2/TRI7 VS_IN2/TRI8
18
HS_IN1/TRI5 VS_IN1/TRI6
AVR 2650
harman/kardon
PRELIMINARY
ADV7844
Table 6. Function Descriptions

Pin
No.
A1
A2
Mnemonic
GND
VS/FIELD
Type
Ground
Digital video
output
A3
A4
A5
A6
A7
A8
A9
A10
E2_TX+
E2_RX+
TVDD
RXD_2RXD_1RXD_0RXD_CHEAC_2-
Digital output
Digital input
Power
HDMI input
HDMI input
HDMI input
HDMI input
HDMI input/output
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
TVDD
RXC_2RXC_1RXC_0RXC_CNC
TVDD
RXB_2RXB_1RXB_0RXB_CHEAC_1-
Power
HDMI input
HDMI input
HDMI input
HDMI input
No connect
Power
HDMI input
HDMI input
HDMI input
HDMI input
HDMI input/output
A23
B1
GND
HS/CS
Ground
Digital video
output
B2
FIELD/DE
Miscellaneous
digital
B3
B4
B5
B6
B7
B8
B9
B10
E2_TXE2_RXTVDD
RXD_2+
RXD_1+
RXD_0+
RXD_C+
HEAC_2+
Digital output
Digital input
Power
HDMI input
HDMI input
HDMI input
HDMI input
HDMI input/output
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
TVDD
RXC_2+
RXC_1+
RXC_0+
RXC_C+
NC
TVDD
RXB_2+
RXB_1+
RXB_0+
RXB_C+
Power
HDMI input
HDMI input
HDMI input
HDMI input
No Connect
Power
HDMI input
HDMI input
HDMI input
HDMI input
Description
Ground
VS is a vertical synchronization output signal. FIELD is a field
synchronization output signal in all interlaced video modes. VS or FIELD can
be configured for this pin.
Digital Output Channel 2 True of Ethernet Interface
Digital Input Channel 2 True of Ethernet Interface
Terminator Supply Voltage (3.3 V).
Digital Input Channel 2 Complement of Port D in the HDMI Interface.
Digital Input Clock Complement of Port D in the HDMI Interface.
HDMI Ethernet and Audio Return Channel (HEAC) Complement Channel 2 in
HDMI Interface
Digital Input Channel 2 Complement of Port C in the HDMI Interface.
Digital Input Clock Complement of Port C in the HDMI Interface.
No Connect.
Digital Input Channel 2 Complement of Port B in the HDMI Interface.
Digital Input Clock Complement of Port B in the HDMI Interface.
HDMI Ethernet and Audio Return Channel (HEAC) Complement Channel 1 in
HDMI Interface
Ground
HS is a horizontal synchronization output signal. CS (composite
synchronization) signal is a single signal containing both horizontal and
vertical synchronization pulses.
DE (data enable) is a signal that indicates active pixel data. FIELD is a field
synchronization output signal in all interlaced video modes. DE or FIELD can
be configured for this pin.
Digital Output Channel 2 Complimentary of Ethernet Interface
Digital Input Channel 2 Complimentary of Ethernet Interface
Digital Input Channel 2 True of Port D in the HDMI Interface.
Digital Input Clock True of Port D in the HDMI Interface.
HDMI Ethernet and Audio Return Channel (HEAC) True Channel 2 in HDMI
Interface
Digital Input Channel 2 True Of Port C in the HDMI Interface.
Digital Input Clock True Of Port C in the HDMI Interface.
No Connect.
Digital Input Channel 2 True of Port B in the HDMI Interface.
Digital Input Clock True of Port B in the HDMI Interface.
125
AVR 2650
harman/kardon
ADV7844
PRELIMINARY
Pin
No.
B22
Mnemonic
HEAC_1+
Type
HDMI input/output
B23
C1
GND
P0
C2
P1
C3
C4
C5
C6
E1_TX+
E1_RX+
TVDD
C7
C8
HPA_D
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
D1
RXD_5V
RXC_5V
TVDD
GND
GND
GND
GND
GND
GND
TVDD
TVDD
TVDD
TVDD
TVDD
TVDD
P2
D2
P3
D3
D4
D5
D6
E1_TXE1_RXTVDD
SYNC_OUT
D7
CEC
D8
HPA_C
D9
D10
RXB_5V
HPA_B
D11
D12
D13
TVDD
RXA_5V
HPA_A
D14
D15
DDCD_SDA
DDCD_SCL
Ground
Digital video
output
Digital video
output
Digital output
Digital input
Power
Miscellaneous
digital
Test pin
Miscellaneous
digital
HDMI input
HDMI input
Power
Ground
Ground
Ground
Ground
Ground
Ground
Power
Power
Power
Power
Power
Power
Digital video
output
Digital video
output
Digital output
Digital input
Power
Miscellaneous
digital
Digital
input/output
Miscellaneous
digital
HDMI input
Miscellaneous
digital
Power
HDMI input
Miscellaneous
digital
HDMI input
HDMI input
D16
D17
D18
DDCC_SDA
DDCC_SCL
RTERM
HDMI input
HDMI input
Miscellaneous
PWRDN1
PWRDN2
Description
HDMI Ethernet and Audio Return Channel (HEAC ) True Channel 1 in HDMI
Interface
Ground
Video Pixel Output Port.
Digital Output Channel 1 True of Ethernet Interface
Digital Input Channel 1 True of Ethernet Interface
Controls the Power-Up of the ADV7844. Should be connected to a digital 3.3
V I/O supply to power up the ADV7844.
This pin should be connected to the ground.
Hot Plug Assert signal output for HDMI port D.
5 V Detect Pin for Port D in the HDMI Interface.
5 V Detect Pin for Port C in the HDMI Interface.
Ground
Ground
Ground
Ground
Ground
Ground
Digital Output Channel 1 Complimentary of Ethernet Interface
Digital Input Channel 1 Complimentary of Ethernet Interface
Sliced synchronization output.
Consumer Electronic Control Channel.
Hot Plug Assert signal output for HDMI port C.
5 V Detect Pin for Port B in the HDMI Interface.
Hot Plug Assert signal output for HDMI port B.
5 V Detect Pin for Port A in the HDMI Interface.
Hot Plug Assert signal output for HDMI port A.
HDCP Slave Serial Data Port D. DDCD_SDA is a 3.3 V input that is 5 V tolerant.
HDCP Slave Serial Clock Port D. DDCD_SCL is a 3.3 V input that is 5 V
tolerant.
HDCP Slave Serial Data Port C. DDCC_SDA is a 3.3 V input that is 5 V tolerant.
HDCP Slave Serial Clock Port C. DDCC_SCL is a 3.3 V input that is 5 V tolerant.
Sets Internal Termination Resistance. A 500 resistor between this pin and
126
AVR 2650
harman/kardon
PRELIMINARY
Pin
No.
Mnemonic
D19
D20
D21
D22
D23
E1
E2
E3
E4
E20
E21
E22
E23
F1
DDCB_SDA
DDCB_SCL
TVDD
RXA_2+
RXA_2DVDDIO
DVDDIO
GND
GND
DDCA_SDA
CVDD
RXA_1+
RXA_1P5
F2
P4
F3
F4
F20
EP_MISO
EP_MOSI
DDCA_SCL
F21
F22
F23
G1
CVDD
RXA_0+
RXA_0P7
G2
P6
G3
G4
G7
G8
G9
G10
G11
G12
G13
G14
G15
G16
G17
G20
EP_SCK
GND
GND
GND
GND
TEST1
TEST2
GND
GND
CVDD
CVDD
CVDD
VGA_SCL
G21
G22
G23
H1
CVDD
RXA_C+
RXA_CP9
H2
P8
H3
TTX_SDA
H4
TTX_SCL
EP_CS
ADV7844
Type
analog
HDMI input
HDMI input
Power
HDMI input
HDMI input
Power
Power
Ground
Ground
HDMI input
Power
HDMI input
HDMI input
Digital video
output
Digital video
output
Digital output
Digital input
HDMI input
Power
HDMI input
HDMI input
Digital video
output
Digital video
output
Digital output
Digital output
Ground
Ground
Ground
Ground
Test
Test
Ground
Ground
Power
Power
Power
Miscellaneous
digital
Power
HDMI input
HDMI input
Digital video
output
Digital video
output
Miscellaneous
digital
Miscellaneous
digital
Description
GND should be used.
HDCP Slave Serial Data Port B. DDCB_SDA is a 3.3 V input that is 5 V tolerant.
HDCP Slave Serial Clock Port B. DDCB_SCL is a 3.3 V input that is 5 V tolerant.
Digital Input Channel 2 True of Port A in the HDMI Interface.
Digital Input Channel 2 Complement of Port A in the HDMI Interface.
Digital I/O Supply Voltage (3.3 V).
Ground
Ground
HDCP Slave Serial Data Port A. DDCA_SDA is a 3.3 V input that is 5 V tolerant.
Comparator Supply Voltage (1.8 V).
SPI Master In/Slave Out for External EDID Interface.
SPI Master Out/Slave In for External EDID Interface.
HDCP Slave Serial Clock Port A. DDCA_SCL is a 3.3 V input that is 5 V
tolerant.
SPI Chip Select for External EDID Interface.
SPI Clock for External EDID Interface.
Ground
Ground
Ground
Ground
Do Not Connect.
Do Not Connect.
Ground
Ground
DDC Port Serial Clock Input for VGA
Digital Input Clock True of Port A in the HDMI Interface.
Digital Input Clock Complement of Port A in the HDMI Interface.
I2C Port Serial Data Input/Output Pin. SDA is the data line for the teletext
port.
I2C Port Serial Clock Input. SCL is the clock line for the teletext port.
127
AVR 2650
harman/kardon
ADV7844
Pin
No.
H7
H8
H9
H10
H11
H12
H13
H14
H15
H16
H17
H20
Mnemonic
GND
GND
GND
GND
GND
GND
GND
GND
CVDD
CVDD
CVDD
VGA_SDA
H21
H22
H23
J1
CVDD
NC
NC
P11
J2
P10
J3
J4
MCLK
AP0
J7
J8
J9
J10
J11
J12
J13
J14
J15
J16
J17
J20
J21
J22
J23
K1
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
PVDD
TEST3
GND
GND
P13
K2
P12
K3
AP5
K4
SCLK
K7
K8
K9
K10
K11
K12
VDD
GND
GND
GND
GND
GND
PRELIMINARY
Type
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Power
Power
Power
Miscellaneous
digital
Power
No Connect
No Connect
Digital video
output
Digital video
output
Miscellaneous
Miscellaneous
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Power
Test
Ground
Ground
Digital video
output
Digital video
output
Miscellaneous
Miscellaneous
digital
Power
Ground
Ground
Ground
Ground
Ground
Description
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
DDC Port Data Clock Input for VGA
No Connect
No Connect
Audio Master Clock Output.
Audio Output Pin. Pins AP0-AP5 can be configured to output SPDIF Digital
Audio Output (SPDIF), High Bit Rate (HBR), Direct Stream Digital (DSD),
Direct Stream Transfer (DST) or I2S.
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
PLL Supply Voltage (1.8 V).
Do Not Connect.
Ground
Ground
Audio Serial Clock Output.
Digital Core Supply Voltage (1.8 V).
Ground
Ground
Ground
Ground
Ground
Rev. PrBC | 128 16 of 35
Page
AVR 2650
harman/kardon
PRELIMINARY
ADV7844
Pin
No.
K13
K14
K15
K16
K17
K20
K21
K22
Mnemonic
GND
GND
GND
GND
GND
PVDD
GND
XTALN
K23
XTALP
L1
L2
L3
L4
L7
L8
L9
L10
L11
L12
L13
L14
L15
L16
L17
L20
L21
L22
L23
M1
DVDDIO
DVDDIO
GND
GND
VDD
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
P15
M2
P14
M3
AP4
Type
Ground
Ground
Ground
Ground
Ground
Power
Ground
Miscellaneous
analog
Miscellaneous
analog
Power
Power
Ground
Ground
Power
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Digital video
output
Digital video
output
Miscellaneous
M4
AP3
Miscellaneous
M7
M8
M9
M10
M11
M12
M13
M14
M15
M16
M17
M20
M21
M22
VDD
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
REFN
Power
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Miscellaneous
Description
Ground
Ground
Ground
Ground
Ground
Ground
Input Pin for 28.63636 MHz Crystal.
Crystal Input. Input pin for 28.63636 MHz Crystal or an External 1.8 V,
28.63636 MHz Clock Oscillator Source to Clock the ADV7844.
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Internal Voltage Reference Output.
129
AVR 2650
harman/kardon
ADV7844
PRELIMINARY
Pin
No.
Mnemonic
M23
REFP
N1
P17
N2
P16
N3
AP2
Type
analog
Miscellaneous
analog
Digital video
output
Digital video
output
Miscellaneous
N4
AP1
Miscellaneous
N7
N8
N9
N10
N11
N12
N13
N14
N15
N16
N17
N20
N21
N22
N23
P1
VDD
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
AVDD
AVDD
AVDD
AVDD
P18
P2
P19
P3
SCL
P4
SDA
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P20
P21
P22
P23
R1
VDD
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
AVDD
AVDD
AIN11
AIN12
P20
R2
P21
R3
TEST4
Power
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Power
Power
Power
Power
Digital video
output
Digital video
output
Miscellaneous
digital
Miscellaneous
digital
Power
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Power
Power
Analog video input
Analog video input
Digital video
output
Digital video
output
Test
Description
Internal Voltage Reference Output.
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Analog Supply Voltage (1.8 V).
I2C Port Serial Clock Input. SCL is the clock line for the control port.
I2C Port Serial Data Input/Output Pin. SDA is the data line for the control
port.
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Analog Video Input Channel.
Do Not Connect.
130
AVR 2650
harman/kardon
PRELIMINARY
ADV7844
Pin
No.
R4
Mnemonic
INT1
Type
Miscellaneous
digital
R7
R8
R9
R10
R11
R12
R13
R14
R15
R16
R17
R20
VDD
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
HS_IN2/TRI7
Power
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Miscellaneous
analog
R21
VS_IN2/TRI8
Miscellaneous
analog
R22
SYNC4
R23
T1
AIN10
P22
T2
P23
T3
T4
TEST5
INT2
Miscellaneous
analog
Analog video input
Digital video
output
Digital video
output
Test
Miscellaneous
digital
T7
T8
T9
T10
T11
T12
T13
T14
T15
T16
T17
T20
T21
T22
T23
U1
U2
U3
U4
U7
U8
U9
U10
VDD
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
DVDDIO
DVDDIO
DVDDIO
DVDDIO
VDD
VDD
VDD
VDD
Power
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Power
Power
Power
Power
Power
Power
Power
Power
Description
Interrupt. This pin can be active low or active high. When status bits change,
this pin is triggered. The events that trigger an interrupt are under user
control.
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
HS on Graphics Port 2. The HS input signal is used for 5-wire timing mode.
This pin can also be used as a trilevel/bilevel input on the SCART or Dterminal connector. Result available via I2C.
VS on Graphics Port 2. The VS input signal is used for 5-wire timing mode.
This pin can also be used as a trilevel/bilevel input on the SCART or Dterminal connector. Result available via I2C.
This is a synchronization on green or luma input (SOG/SOY) used in
embedded synchronization mode. User configurable.
Do Not Connect.
Interrupt. This pin can be active low or active high. When status bits change,
this pin is triggered. The events that trigger an interrupt are under user
control.
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
131
AVR 2650
harman/kardon
ADV7844
PRELIMINARY
Pin
No.
U11
U12
U13
U14
U15
U16
U17
U20
Mnemonic
VDD
VDD
VDD
VDD
GND
GND
GND
TRI4
U21
TRI3
U22
U23
V1
AIN9
AIN8
LLC
V2
P24
V3
RESET
V4
AVLINK
V20
TRI1
V21
TRI2
V22
SYNC3
V23
W1
AIN7
P25
W2
P26
W3
W4
NC
SPDIF_IN
W20
W21
W22
W23
Y1
AVDD
AVDD
AVDD
AVDD
P27
Y2
P28
Y3
Y4
Y5
Y6
GND
GND
GND
VDD_SDRAM
Y7
Y8
Y9
Y10
SDRAM_A11
SDRAM_A6
SDRAM_A2
SDRAM_CS
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
Y11
SDRAM_LDQS
SDRAM interface
Y12
GND
Ground
Type
Power
Power
Power
Power
Ground
Ground
Ground
Miscellaneous
analog
Miscellaneous
analog
Analog video input
Analog video input
Digital video
output
Digital video
output
Miscellaneous
digital
Digital
input/output
Miscellaneous
analog
Miscellaneous
analog
Miscellaneous
analog
Analog video input
Digital video
output
Digital video
output
No connect
Miscellaneous
digital
Power
Power
Power
Power
Digital video
output
Digital video
output
Ground
Ground
Ground
Power
Description
Ground
Ground
Ground
Trilevel/Bilevel Input on the SCART or D-Terminal Connector. Result available
via I2C.
via I2C.
Line-Locked Output Clock for the Pixel Data (Range is 13.5 MHz to 170 MHz).
System Reset Input. Active low. A minimum low reset pulse width of 5 ms is
required to reset the ADV7844 circuitry.
Digital SCART Control Channel.
via I2C.
via I2C.
No Connect.
Audio Clock Input Pin for SPDIF
Ground
Ground
Ground
External Memory Interface Digital Input/Output Supply (DDR 2.5 V or SDR
3.3 V).
Address Output. Interface to external RAM address lines.
Chip Select. SDRAM_CS enables and disables the command decoder on the
RAM. One of four command signals to the external SDRAM.
Lower Data Strobe Pin. Data strobe pins are used for the RAM interface. This
is an output with read data and an input with write data. It is edge aligned
with write data and centered in read data. SDRAM_ LDQS corresponds to
the data on SDRAM_DQ0 to SDRAM_
Ground

132
AVR 2650
harman/kardon
PRELIMINARY
ADV7844
Pin
No.
Y13
Y14
Y15
Y16
Y17
Mnemonic
SDRAM_DQ6
SDRAM_DQ2
SDRAM_DQ15
SDRAM_DQ11
SDRAM_CKE
Type
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
Y18
VDD_SDRAM
Power
Y19
Y20
GND
AOUT
Y21
Y22
Y23
AA1
NC
AIN5
AIN6
P29
AA2
P30
AA3
AA4
AA5
AA6
GND
GND
GND
VDD_SDRAM
Ground
Analog monitor
output
No connect
Analog video input
Analog video input
Digital video
output
Digital video
output
Ground
Ground
Ground
Power
AA7
AA8
AA9
AA10
SDRAM_A9
SDRAM_A5
SDRAM_A1
SDRAM_RAS
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
AA11
AA12
AA13
AA14
AA15
AA16
AA17
SDRAM_DQ7
GND
SDRAM_DQ5
SDRAM_DQ1
SDRAM_DQ12
SDRAM_DQ8
SDRAM_CK
SDRAM interface
Ground
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
AA18
VDD_SDRAM
Power
AA19
AA20
AA21
AA22
GND
NC
NC
SYNC2
AA23
AB1
AIN4
P31
AB2
P32
AB3
P34
AB4
AB5
AB6
AB7
AB8
NC
GND
DVDDIO
SDRAM_A8
SDRAM_A4
Ground
No connect
No connect
Miscellaneous
analog
Analog video input
Digital video
output
Digital video
output
Digital video
output
No connect
Ground
Power
SDRAM interface
SDRAM interface
Description
Data Bus. Interface to external RAM 16-bit data bus.
Clock Enable. This pin acts as an enable to the clock signals of the external
RAM.
3.3 V).
Ground
Analog Monitor Output.
No Connect.
Ground
Ground
Ground
3.3 V).
Row Address Select Command Signal. One of four command signals to the
external SDRAM.
Ground
Differential Clock Output. All address and control output signals to the RAM
should be sampled on the positive edge of SDRAM_CK and on the negative
edge of SDRAM_CK.
3.3 V).
Ground
No Connect.
No Connect.
No Connect.
Ground
133
AVR 2650
harman/kardon
ADV7844
PRELIMINARY
Pin
No.
AB9
AB10
AB11
Mnemonic
SDRAM_A0
SDRAM_BA1
SDRAM_CAS
Type
SDRAM interface
SDRAM interface
SDRAM interface
AB12
VDD_SDRAM
Power
AB13
AB14
AB15
AB16
AB17
SDRAM_DQ4
SDRAM_DQ0
SDRAM_DQ13
SDRAM_DQ9
SDRAM_CK
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
AB18
VDD_SDRAM
Power
AB19
AB20
GND
SYNC1
AB21
HS_IN1/TRI5
AB22
VS_IN1/TRI6
AB23
AC1
AC2
GND
GND
P33
AC3
P35
AC4
AC5
AC6
AC7
AC8
AC9
AC10
AC11
NC
GND
DVDDIO
SDRAM_A7
SDRAM_A3
SDRAM_A10
SDRAM_BA0
SDRAM_WE
Ground
Miscellaneous
analog
Miscellaneous
analog
Miscellaneous
analog
Ground
Ground
Digital video
output
Digital video
output
No connect
Ground
Power
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
AC12
VDD_SDRAM
Power
AC13
AC14
AC15
AC16
AC17
SDRAM_DQ3
SDRAM_VREF
SDRAM_DQ14
SDRAM_DQ10
SDRAM_UDQS
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
SDRAM interface
AC18
VDD_SDRAM
Power
AC19
AC20
AC21
AC22
AC23
GND
AIN1
AIN2
AIN3
GND
Ground
Analog video input
Analog video input
Analog video input
Ground
Description
Bank Address Output. Interface to external RAM bank address lines.
Column Address Select Command Signal. One of four command signals to
the external SDRAM.
3.3 V).
Differential Clock Output. All address and control output signals to the RAM
should be sampled on the positive edge of SDRAM_CK and on the negative
edge of SDRAM_CK.
3.3 V).
Ground
HS on Graphics Port 1. The HS input signal is used for 5-wire timing mode.
HS_IN1/TRI5 is a 3.3 V input that is 5 V tolerant.
Vertical Synchronization Input Signal. Used for 5-wire timing mode.
Ground
Ground
No Connect.
Ground
Bank Address Output. Interface to external RAM bank address lines.
Write Enable Output Command Signal. One of four command signals to the
external SDRAM.
3.3 V).
1.25 V Reference for DDR SDRAM Interface or 1.65 V for SDR.
Upper Data Strobe Pin. Data strobe pins for the RAM interface. This is an
output with read data and an input with write data. It is edge aligned with
write data and centered in read data. UDQS corresponds to the data on DQ8
to DQ16.
3.3 V).
Ground
Ground
Rev. PrBC | 134 22 of 35

Page
AVR 2650
harman/kardon
HDMI 1.4 Mux with

Xpressview Fast Switching
ADV3014
ADI Confidential
EQ
RXD_0
RXD_1
RXD_2
RXD_C
EQ
TMDS
AND DDC
HDCP
DECRYPTION ENGINE
RX0
RX1
RX2
RXC
INT1
INT2
INT_TX
PACKET
PROCESSOR
INFOFRAME/
PACKET MEMORY
HDCP KEYS
CEC
CEC CONTROLLER
PWRDN
RESET
GLOBAL CONTROLS
ADV3014
09068-001
RXC_0
RXC_1
RXC_2
RXC_C
HDMI ENCODER
AND TMDS
EQ
INTERRUPT
CONTROLLER
RXB_0
RXB_1
RXB_2
RXB_C
HDCP
ENCRYPTION
ENGINE
EQ
SYNC
MEASUREMENT
TMDS
AND DDC
RXA_0
RXA_1
RXA_2
RXA_C
Xpressview FAST
SWITCHING RECEIVER
PROCESSOR
4-input, 1-output HDMI mux

HDMI 1.4a support: 3D TV formats, content type bits,
CEC 1.4-compatible
Xpressview fast switching on all HDMI input ports
High-bandwidth digital content protection (HDCP 1.4a)
HDCP repeater support
225 MHz HDMI Rx and Tx support 36-/30-/24-bit Deep Color
Ultralow jitter digital PLL (100% deskew)
Quad HDMI Rx input
Adaptive equalizer for cable lengths up to 30 meters
Internal extended display identification data (EDID) RAM
EDID replication (512 bytes per port)
EDID with HDMI cable 5 V power support
5 V detect inputs
Hot plug assertion control pins
Single HDMI Tx output: EDID data extraction and hot plug
detect (HPD) input
HDMI 1.4a audio pass-through support
I2S, DSD, and HBR, including Dolby TrueHD and
DTS-HD master audio
General
Interrupt controller with 3 interrupt outputs
Software libraries, driver, and application available
2-layer PCB design supported
144-lead, 20 mm 20 mm LQFP package
TMDS
AND DDC
TMDS
AND DDC
FEATURES
Figure 1.
input HDMI ports. Using the Analog Devices hardware-based

HDCP engine that minimizes software overhead, Xpressview
technology allows fast switching between any HDMI input
ports in less than 1 second.
The ADV3014 supports all mandatory HDMI 1.4a 3D TV formats
in addition to all HD TV formats up to 1080p 36-bit Deep Color.
The ADV3014 also features an integrated HDMI 1.4 CEC controller, which supports capability discovery and control (CDC).
APPLICATIONS
Port expansion for Analog Devices HDMI decoders
Audio video receivers (AVRs)
Home theater in a box (HTiB)
Sound bar with HDMI repeater support
Flat panel TVs
Other repeater applications
The HDMI receiver supports programmable/adaptive equalization that ensures robust operation of the interface at cable lengths
of up to 30 meters.
The ADV3014 offers integrated control of hot plug circuits,
sensing of 5 V input signals and on-board EDID controls with
EDID replication and power-down mode EDID.
GENERAL DESCRIPTION
The ADV3014 supports pass-through of all HDMI 1.4a audio

formats including I2S, DSD, and HBR formats such as Dolby
TrueHD and DTS-HD master audio.
The ADV3014 is a high performance, four-input, one-output,

High-Definition Multimedia Interface (HDMI) switch that
integrates HDMI 1.4a receiver and transmitter functions onto
one chip. It supports all HDCP repeater functions through fully
tested Analog Devices, Inc., repeater software libraries and drivers.
The ADV3014 incorporates Xpressview fast switching on all
Fabricated in an advanced CMOS process, the ADV3014 is

provided in a space-saving, 144-lead, 20 mm 20 mm LQFP
surface-mount, Pb-free package. It is specified over the 0C to
70C temperature range.
135
AVR 2650
harman/kardon
ADI Confidential
ADV3014
DETAILED FUNCTIONAL BLOCK DIAGRAM

TX
PLL
XTAL
XTAL1
RXA_C+/RXA_C
RXB_C+/RXB_C
RXC_C+/RXC_C
RXD_C+/RXD_C
VIDEO/AUDIO
CLOCK
GENERATION
RX
PLL
EQUALIZER
SAMPLER
SAMPLER
RXD_0+/RXD_0
RXD_1+/RXD_1
RXD_2+/RXD_2
EQUALIZER
CH0
CH1
SAMPLER
5V_DETA
5V_DETB
5V_DETC
5V_DETD
SYNC
MEASUREMENT
HDCP
DECRYPTION
ENGINE
5V DETECT
PACKET
PROCESSOR
INFOFRAME
PACKET
MEMORY
EP_MISO
EP_MOSI
EP_CS
EP_SCK
SPI MASTER/
SLAVE
RESET
SCL
SDATA
ALSB
CS
INTERRUPT
CONTROLLER
RX HPD
CONTROLLER
PWRDN
HP_TX
TXDDC_SDA
TXDDC_SCL
HDCP KEYS
HP_CTRLA
HP_CTRLB
HP_CTRLC
HP_CTRLD
DDCA_SDA
DDCA_SCL
DDCB_SDA
DDCB_SCL
DDCC_SDA
DDCC_SCL
DDCD_SDA
DDCD_SCL
TXC+/TXC
TX0+/TX0
TX1+/TX1
TX2+/TX2
INT1
INT2
INT_TX
EDID
RAM
RX EDID/
REPEATER
CONTROLLER
GLOBAL
CONTROLS
I2C
CONTROLLER
ADV3014
Figure 2. Detailed Functional Block Diagram
Rev. Sp0 | Page 3 of 16

136
09068-001
CEC
CEC
CONTROLLER
CH2
TX HPD
CONTROLLER
EQUALIZER
VIDEO DATA
DE
VS
HS
AUDIO DATA
EDID/HDCP
BUFFER
RXC_0+/RXC_0
RXC_1+/RXC_1
RXC_2+/RXC_2
XPRESSVIEW
FAST SWITCHING
RECEIVER
PROCESSOR
+
BACKGROUND
MEASUREMENT
TX
EDID/HDCP
CONTROLLER
RXB_0+/RXB_0
RXB_1+/RXB_1
RXB_2+/RXB_2
SERIALIZER
TMDS DRIVERS
SAMPLER
HDMI
ENCODER
EQUALIZER
HDCP
ENCRYPTION
ENGINE
RXA_0+/RXA_0
RXA_1+/RXA_1
RXA_2+/RXA_2
AVR 2650
harman/kardon
ADV3014
ADI Confidential
109
108
PIN 1
107
106
105
104
103
102
101
100
10
99
11
98
12
97
13
96
14
95
15
94
16
93
ADV3014
18
19
20
92
TOP VIEW
(Not to Scale)
17
90
91
89
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
TXPLVDD
TXPGND
TXPLGND
EXT_SWING
HP_TX
TEST0
TXDDC_SDA
TXDDC_SCL
TXAVDD
TXGND
TXC
TXC+
TXGND
TX0
TX0+
TXGND
TX1
TX1+
TXAVDD
TX2
TX2+
TXGND
CEC
DGND
DVDD
ALSB
CS
EP_SCK
EP_CS
EP_MOSI
EP_MISO
TEST1
TEST2
TEST3
TEST4
DGNDIO
54
73
53
74
36
52
75
35
51
76
34
50
77
33
49
78
32
48
79
31
47
80
30
46
81
29
45
82
28
44
83
27
43
84
26
42
85
25
41
86
24
40
87
23
39
88
22
38
21
DDCA_SDA
RTERM
5V_DETA
HP_CTRLA
PGND
PVDD
XTAL1
XTAL
PVDD
PGND
PWRDN
RESET
TEST16
TEST15
TEST14
DVDD
DGND
TEST13
TEST12
TEST11
TEST10
TEST9
DVDDIO
DGNDIO
INT_TX
INT2
INT1
DVDD
DGND
SCL
SDATA
TEST8
TEST7
TEST6
TEST5
DVDDIO
Figure 4. Pin Configuration
Table 5: Pin Function Descriptions

Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
Mnemonic
DDCC_SCL
CVDD
CGND
RXC_C
RXC_C+
TVDD
RXC_0
RXC_0+
CGND
RXC_1
RXC_1+
TVDD
RXC_2
Type
Digital input
Power
Ground
HDMI input
HDMI input
Power
HDMI input
HDMI input
Ground
HDMI input
HDMI input
Power
HDMI input
Description
HDCP Slave Serial Clock Port C. DDCC_SCL is a 3.3 V input that is 5 V tolerant.
Receiver Comparator Supply Voltage (1.8 V).
TVDD and CVDD Ground.
Digital Input Clock Complement of Port C in the HDMI Interface.
Digital Input Clock True of Port C in the HDMI Interface.
Receiver Terminator Supply Voltage (3.3 V).
Digital Input Channel 0 True of Port C in the HDMI Interface.
137
09068-002
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
37
DDCC_SCL
CVDD
CGND
RXC_C
RXC_C+
TVDD
RXC_0
RXC_0+
CGND
RXC_1
RXC_1+
TVDD
RXC_2
RXC_2+
HP_CTRLD
5V_DETD
DGND
DVDD
DDCD_SDA
DDCD_SCL
CVDD
CGND
RXD_C
RXD_C+
TVDD
RXD_0
RXD_0+
CGND
RXD_1
RXD_1+
TVDD
RXD_2
RXD_2+
CVDD
CGND
TXPVDD
143
144
DDCC_SDA
5V_DETC
HP_CTRLC
RXB_2+
RXB_2
TVDD
RXB_1+
RXB_1
CGND
RXB_0+
RXB_0
TVDD
RXB_C+
RXB_C
CGND
CVDD
DDCB_SCL
DDCB_SDA
DVDD
DGND
5V_DETB
HP_CTRLB
RXA_2+
RXA_2
TVDD
RXA_1+
RXA_1
CGND
RXA_0+
RXA_0
TVDD
RXA_C+
RXA_C
CGND
CVDD
DDCA_SCL
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
AVR 2650
harman/kardon
ADI Confidential
Pin No.
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Mnemonic
RXC_2+
HP_CTRLD
5V_DETD
DGND
DVDD
DDCD_SDA
DDCD_SCL
CVDD
CGND
RXD_C
RXD_C+
TVDD
RXD_0RXD_0+
CGND
RXD_1
RXD_1+
TVDD
RXD_2
RXD_2+
CVDD
CGND
TXPVDD
Type
HDMI input
Digital output
HDMI input
Ground
Power
Digital I/O
Digital Input
Power
Ground
HDMI input
HDMI input
Power
HDMI input
HDMI input
Ground
HDMI input
HDMI input
Power
HDMI input
HDMI input
Power
Ground
Power
37
38
39
40
TXPLVDD
TXPGND
TXPLGND
EXT_SWING
Power
Ground
Ground
Analog input
41
HP_TX
Analog input
42
43
TEST0
TXDDC_SDA
Test pin
Digital I/O
44
TXDDC_SCL
Digital output
45
46
47
TXAVDD
TXGND
TXC
Power
Ground
HDMI output
48
TXC+
HDMI output
49
50
TXGND
TX0
Ground
HDMI output
51
TX0+
HDMI output
52
53
TXGND
TX1
Ground
HDMI output
54
TX1+
HDMI output
55
56
TXAVDD
TX2
Power
HDMI output
ADV3014
Description
Hot Plug Control Output for Port D. This pin is 5 V tolerant.
5 V Detect Pin for Port D in the HDMI Interface. This pin is 5 V tolerant.
DVDD Ground.
Digital Supply Voltage (1.8 V).
HDCP Slave Serial Data Port D. DDCD_SDA is a 3.3 V input that is 5 V tolerant.
HDCP Slave Serial Clock Port D. DDCD_SCL is a 3.3 V input that is 5 V tolerant.
Digital Input Clock Complement of Port D in the HDMI Interface.
Digital Input Clock True of Port D in the HDMI Interface.
1.8 V PLL Power Supply. These pins provide power to the digital portion of the clock PLL. The
designer should provide quiet, noise-free power to these pins.
1.8 V power supply
TXPVDD Ground.
TXPLVDD Ground
Sets Internal Reference Currents. Place an 887 resistor (1% tolerance) between this pin and
ground.
Hot Plug Detect Signal. This pin indicates to the interface whether the receiver is connected.
This pin is 5 V tolerant.
Connect to ground.
Serial Port Data I/O to Receiver. This pin serves as the master to the DDC bus. This pin is 5 V
tolerant.
Serial Port Data Clock to Receiver. This pin serves as the master clock for the DDC bus.
This pin is 5 V tolerant.
1.8 V Power Supply for TMDS Outputs.
TXAVDD Ground.
Differential Clock Output. Differential clock output at the TMDS clock rate; supports
TMDS logic level.
Differential Clock Output. Differential clock output at the TMDS clock rate; supports
TMDS logic level.
TXAVDD Ground.
Differential Output Channel 0 Complement. Differential output of the red data at 10
the pixel clock rate; supports TMDS logic level.
Differential Output Channel 0 True. Differential output of the red data at 10 the pixel clock
rate; supports TMDS logic level.
TXAVDD Ground.
Differential Output Channel 1 True. Differential output of the red data at 10 the pixel
clock rate; supports TMDS logic level.
1.8 V Power Supply for TMDS Outputs.
138
AVR 2650
harman/kardon
ADV3014
ADI Confidential
Pin No.
57
Mnemonic
TX2+
Type
HDMI output
58
59
60
61
62
63
TXGND
CEC
DGND
DVDD
ALSB
CS
Ground
Digital I/O
Ground
Power
Digital input
Digital input
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
EP_SCK
EP_CS
EP_MOSI
EP_MISO
TEST1
TEST2
TEST3
TEST4
DGNDIO
DVDDIO
TEST5
TEST6
TEST7
TEST8
SDATA
SCL
DGND
DVDD
INT1
Digital output
Digital output
Digital output
Digital input
Test pin
Test pin
Test pin
Test pin
Ground
Power
Test pin
Test pin
Test pin
Test pin
Digital I/O
Digital input
Ground
Power
Digital output
83
INT2
Digital output
84
85
86
87
88
89
90
91
92
93
94
95
96
97
INT_TX
DGNDIO
DVDDIO
TEST9
TEST10
TEST11
TEST12
TEST13
DGND
DVDD
TEST14
TEST15
TEST16
RESET
Digital output
Ground
Power
Test pin
Test pin
Test pin
Test pin
Test pin
Ground
Power
Test pin
Test pin
Test pin
Digital input
98
PWRDN
Digital input
99
100
101
PGND
PVDD
XTAL
Ground
Power
Miscellaneous
analog
Description
Differential Output Channel 2 True. Differential output of the red data at 10 the pixel
clock rate; supports TMDS logic level.
TXAVDD Ground.
Consumer Electronics Control Channel. This pin is 5 V tolerant.
DVDD Ground.
This pin is used to set the I2C address of the Rx IO and the Tx main maps.
Chip Select Pin. This pin must be set low or left floating for the chip to process I2C messages
that are destined for the ADV3014. The ADV3014 ignores I2C messages that it receives if
this pin is high.
SPI Clock Interface for the EDID.
SPI Chip Selected Interface for the EDID.
SPI Master Out/Slave In for the EDID.
SPI Master In/Slave Out for the EDID.
Connect to ground.
Connect to ground.
Connect to ground.
Connect to ground.
DVDDIO Ground.
Connect to ground.
Connect to ground.
Connect to ground.
Connect to ground.
I2C Port Serial Data Input/Output Pin. SDATA is the data line for the control port.
I2C Port Serial Clock Input. SCL is the clock line for the control port.
DVDD Ground.
Interrupt Pin. This pin can be active low or active high. When status bits change, this pin is
triggered. The events that trigger an interrupt are under user control.
Interrupt Pin. This pin can be active low or active high. When status bits change, this pin is
triggered. The events that trigger an interrupt are under user control.
Interrupt; Open Drain. A 2 k pull-up resistor to the microcontroller I/O supply is recommended.
DVDDIO Ground.
Leave floating.
Leave floating.
Leave floating.
Leave floating.
Leave floating.
DVDD Ground.
Leave floating.
Leave floating.
Leave floating.
System Reset Input. Active low. A minimum low reset pulse width of 5 ms is required to reset
the ADV3014 circuitry.
Active-Low Power-Down Pin. If used, this pin should be pulled high to power up the
ADV3014. This pin can also be used as an in-system power detect where an internal EDID can
be powered from a 5 V signal of the HDMI port when it is connected to active equipment. This
pin is 5 V tolerant.
PVDD Ground.
Input Pin for 28.63636 MHz Crystal or an External 1.8 V 28.63636 MHz Clock Oscillator Source to
Clock the ADV3014.
139
AVR 2650
harman/kardon
ADI Confidential
Pin No.
102
Mnemonic
XTAL1
103
104
105
106
107
PVDD
PGND
HP_CTRLA
5V_DETA
RTERM
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
DDCA_SDA
DDCA_SCL
CVDD
CGND
RXA_C
RXA_C+
TVDD
RXA_0
RXA_0+
CGND
RXA_1
RXA_1+
TVDD
RXA_2
RXA_2+
HP_CTRLB
5V_DETB
DGND
DVDD
DDCB_SDA
DDCB_SCL
CVDD
CGND
RXB_C
RXB_C+
TVDD
RXB_0
RXB_0+
CGND
RXB_1
RXB_1+
TVDD
RXB_2
RXB_2+
HP_CTRLC
5V_DETC
DDCC_SDA
Type
Miscellaneous
analog
Power
Ground
Digital output
Digital input
Miscellaneous
analog
Digital I/O
Digital input
Power
Ground
HDMI input
HDMI input
Power
HDMI input
HDMI input
Ground
HDMI input
HDMI input
Power
HDMI input
HDMI input
Digital output
Digital input
Ground
Power
Digital I/O
Digital input
Power
Ground
HDMI input
HDMI input
Power
HDMI input
HDMI input
Ground
HDMI input
HDMI input
Power
HDMI input
HDMI input
Digital output
Digital input
Digital I/O
ADV3014
Description
Crystal Output Pin. This pin should be left floating if a clock oscillator is used.
PVDD Ground.
Hot Plug Control Output for Port A. This pin is 5 V tolerant.
5 V Detect Pin for Port A in the HDMI Interface. This pin is 5 V tolerant.
This pin sets the internal termination resistance. A 500 resistor between this pin and
ground should be used.
HDCP Slave Serial Data Port A. DDCA_SDA is a 3.3 V input/output that is 5 V tolerant.
HDCP Slave Serial Clock Port A. DDCA_SCL is a 3.3 V input that is 5 V tolerant.
Digital Input Clock Complement of Port A in the HDMI Interface.
Digital Input Clock True of Port A in the HDMI Interface.
Hot Plug Control Output for Port B. This pin is 5 V tolerant.
5 V Detect Pin for Port B in the HDMI Interface. This pin is 5 V tolerant.
DVDD Ground.
HDCP Slave Serial Data Port B. DDCB_SDA is a 3.3 V input/output that is 5 V tolerant.
HDCP Slave Serial Clock Port B. DDCB_SCL is a 3.3 V input that is 5 V tolerant.
Digital Input Clock Complement of Port B in the HDMI Interface.
Digital Input Clock True of Port B in the HDMI Interface.
Hot Plug Control Output for Port C. This pin is 5 V tolerant.
5 V Detect Pin for Port C in the HDMI Interface. This pin is 5 V tolerant.
HDCP Slave Serial Data Port C. DDCC_SDA is a 3.3 V input/output that is 5 V tolerant.
140
AVR 2650
harman/kardon
141
AVR 2650
harman/kardon
TMP92CD28
CMOS 32-Bit Microcontrollers
TMP92CD28FG / TMP92CD28DFG
Outline and Device Characteristics
The TMP92CD28 is a high-speed advanced 32-bit Microcontroller developed for controlling
equipment which processes mass data.
The TMP92CD28 has a high-performance CPU (900/H1 CPU) and various built-in I/Os.
The TMP92CD28FG and TMP92CD28DFG are housed in a 100-pin flat package.
Device characteristics are as follows:
(1) CPU: 32-bit CPU (900/H1 CPU)
Compatible with 900/L1 instruction code
16 Mbytes of linear address space
General-purpose register and register banks
Micro DMA: 8 channels (250 ns/4 bytes at fSYS = 20 MHz, best case)
(2) Minimum instruction execution time: 50 ns (at fSYS = 20 MHz)

(3) Internal memory
Internal RAM: 32-Kbytes
Internal ROM: 512-Kbytes
142
AVR 2650
harman/kardon
TMP92CD28
(4) External memory expansion
Expandable up to 16 Mbytes (Shared program/data area)
Can simultaneously support 8- or 16-bit width external data bus

Dynamic data bus sizing
Separate bus system
(5) Memory controller

Chip select output: 3 channels
(6) 8-bit timers: 6 channels

(7) 16-bit timers: 2 channels
(8) General-purpose serial interface: 2 channels
UART/synchronous mode: 2 channels (channel 0 , and 1)
IrDA ver.1.0 (115 kbps) mode selectable: 2 channels (channel 0 and 1)
(9) Serial bus interface: 2 channels
2
I C bus mode
Clock synchronous mode (only channel 1)
(10) SPI controller : 1 channel
Supported up to SPI mode of SD card and MMC card
Built-in FIFO buffer of 32 bytes to each Input/Output
(11) High Speed serial interface : 1 channel

Built-in FIFO buffer of 32 bytes to each Input/Output
(12) USB Host Controller : 1chanel
Universal Serial Bus Specification Rev2.0
Open HCI for USB Release 1.0a
12Mbps Full speed support. (Isochronous Transfer is not supported.)
(13) Watchdog timer

(14) Timer for real-time clock (RTC)
(15) Key-on wake up (only for HALT release):4 channels
(16) Program patch logic: 8 banks
(17) Interrupts: 47interrupts
9 CPU interrupts: Software interrupt instruction and illegal instruction
34 internal interrupts: Seven selectable priority levels
4 external interrupts (INT0 to INT3): Seven selectable priority levels

(INT0 to INT3 selectable edge or level interrupt)
(18) Input/output ports: 70pins

(19) Standby function
Three HALT modes: IDLE2 (Programmable), IDLE1, STOP
Power cut mode (Built-in power supply management circuits (PMC) for leak current
provision.)
(20) Clock controller
Built-in two blocks of clock doubler (PLL). PLL supplies 48 MHz for USB and 36 MHz for CPU
from 9MHz
Clock gear function: Select high-frequency clock fc to fc/16
Special timer for CLOCK (fs = 32.768 kHz)

143
AVR 2650
harman/kardon
TMP92CD28
DVCC3A[5]
DVCC3B[1]
DVCC1A[1]
DVCC1B[1]
TLCS-900/H1
DVSS[8]
(PG0)/KI0
(PG1)/KI1
(PG2)/KI2
(PG3)/KI3
(PN1)/SDA0/TA3OUT
(PN2)/SCL0/TA2IN/SI0
(PN3)HSCLK/SCK1
(PN4)SDA1/HSSO/SO1
(PN5)SCL1/HSSI/SI1
PortG
Key-on
Wake up
A
C
E
L
W
B
D
H
X
W
A
XB
C
XD
E
XH
L
Regulator
IX
IY
IZ
SP
32bit
SR
Mode
Controller
P C
Serial Bus I/F

(Ch.0)
PortN
H-OSC
Real Time
X
X2
Clock Gear
L-OSC
Clock
XT2
XT1
Port0
PortF
Serial I/O
(Ch.1)
Program
patch logi
SPIC
8-Banks
A0 to A7(P40 to P47)
Port5
A8 to A15(P50 to P57)
Port6
512-KB ROM
D8 to D15(P10 to P17)
Port4
Serial I/O
(Ch.0)
D0 to D7(P00 to P07)
Port1
HSIO
32-KB RAM
(PF0)TXD0
(PF1)RXD0
(PF2)SCLK0/ CTS0 /CLK
/TB0OUT0
(PF3)TXD1/SPDO
(PF4)RXD1/SPDI
(PF5)SCLK1/ CTS1 /SPCLK
RESET
AM0
AM1
PLL
Watchdog
Timer
Serial Bus I/F

(Ch.1)
RVIN [2]
RVOUT[2]
A16 to A23(P60 to P67)
USB
PortC
Port7
(PC0)INT0
(PC1)INT1
(PC2)INT2/TB1IN0/TB0IN0
(PC3)INT3
Interrupt
Controller
Memory
Controller
(4-Blocks)
Port8
16-BitTimer
(TMRB0)
X1USB(P77)
USBPON(P76)
/USBOC(P75)
TA0IN/(P74)
SRLUB (P73)
SRLLB (P72)
SRWR (P71)
RD (P70)
CS0 /TA1OUT(P80)
CS2 (P82)
CS3 / WAIT /TA5OUT(P83)
8-Bit Timer(TMRA0)
16-Bit Timer
(TMRB1)
D
D-
8-Bit Timer(TMRA2)
8-Bit Timer(TMRA1)
8-Bit Timer(TMRA3)
8-Bit Timer(TMRA4)
PMC
8-Bit Timer(TMRA5)
PWE
( ): Initial function after reset
Figure 1.1 TMP92CD28 Block Diagram
144
AVR 2650
harman/kardon
TMP92CD28
2.
Pin Assignment and Functions

The assignment of input/output pins for the TMP92CD28, their names and functions are as
follows:
Pin Assignment Diagram
80
85
90
95
75
5
70
10
TMP92CD28FG
65
LQFP100
TOPVIEW
15
60
20
50
45
40
35
25
30
55
DVSS
DVCC3A
P10/D8
P11/D9
P12/D10
P13/D11
P14/D12
P15/D13
P16/D14
P17/D15
P40/A0
P41/A1
P42/A2
P43/A3
P44/A4
P45A5
P46/A6
P47/A7
DVSS
DVCC3A
P50/A8
P51/A9
P52/A10
P53/A11
P54/A12
XT2
PWE
DVSS
DVCC1B
RVOUT1
RVIN
RVIN
RVOUT2
DVCC1A
DVSS
P00/D0
P01/D1
P02/D2
P03/D3
P04/D4
P05/D5
P06/D6
P07/D7
Figure 2.1.1 Pin Assignment Diagram (100-pin LQFP)
145
X1
DVSS
X2
AM1
P83/CS3/WAIT/TA5OUT
P82/CS2
P80/CS0/TA1OUT BOOT
P74/TA0IN
P73/SRLUB
P72/SRLLB
P71/SRWR
P70/RD
DVCC3A
DVSS
P67/A23
P66/A22
P65/A21
P64/A20
P63/A19
P62/A18
P61/A17
P60/A16
P57/A15
P56/A14
P55/A13
/RESET
PC0/INT0
PC1/INT1
PC2/INT2/TB1IN0/TB0IN0
PC3/INT3
DVCC3B
XT1
100
DVSS
PG0
PG1
PG2
PG3
DVCC3A
PN5/HSSI/SCL1/SI1
PN4/HSSO/SDA1/SO1
PN3/HSCLK/SCK1
PN2/SCL0/TA2IN
PN1/SDA0/TA3OUT
PF5/SCLK1/CTS1/SPCLK
PF4/RXD1/SPDI
PF3/TXD1/SPDO
PF2/SCLK0/CTS0/CLK/TB0OUT0
PF1/RXD0
PF0/TXD0/
DVSS
P77/X1USB
AM0
DD+
P76/USBPON
P75/USBOC
DVCC3A
Figure 2.1.1 shows the pin assignment of the TMP92CD28FG.
2.1
AVR 2650
harman/kardon
TMP92CD28
Figure 2.1.2 shows the pin assignment of the TMP92CD28DFG.
P76/USBPON
P75/USBOC
DVCC3A
X1
DVSS
X2
AM1
P83/CS3/WAIT/TA5OUT
P82/CS2
P80/CS0/TA1OUT BOOT
P74/TA0IN
P73/SRLUB
P72/SRLLB
P71/SRWR
P70/RD
DVCC3A
DVSS
P67/A23
P66/A22
P65/A21
P64/A20
P63/A19
P62/A18
P56/A14
P55/A13
P54/A12
P53/A11
P61/A17
P60/A16
P57/A15
55
60
65
70
75
50
85
45
TMP92CD28DFG
90
QFP100
40
TOPVIEW
95
30
25
20
15
10
100
35
PG0
DVSS
/RESET
PC0/INT0
PC1/INT1
PC2/INT2/TB1IN0/TB0IN0
PC3/INT3
DVCC3B
XT1
XT2
PWE
DVSS
DVCC1B
RVOUT1
RVIN
RVIN
RVOUT2
DVCC1A
DVSS1
P00/D0
P01/D1
P02/D2
P03/D3
P04/D4
P05/D5
P06/D6
P07/D7
DVSS
DVCC3A
P10/D8
PF2/SCLK0/CTS0/CLK/TB0OUT0
PF3/TXD1/SPDO
PF4/RXD1/SPDI
PF5/SCLK1/CTS1/SPCLK
PN1/SDA0/TA3OUT
PN2/SCL0/TA2IN
PN3/HSCLK/SCK1
PN4/HSSO/SDA1/SO1
PN5/HSSI/SCL1/SI1
DVCC3A
PG3
PG2
PG1
80
D+
DAM0
P77/X1USB
DVSS
PF0/TXD0
PF1/RXD0
Figure 2.1.2 Pin Assignment Diagram (100-pin QFP)
146
P52/A10
P51/A9
P50/A8
DVCC3A
DVSS
P47/A7
P46/A6
P45A5
P44/A4
P43/A3
P42/A2
P41/A1
P40/A0
P17/D15
P16/D14
P15/D13
P14/D12
P13/D11
P12/D10
P11/D9
AVR 2650
harman/kardon
TMP92CD28
2.2
Pin Names and Functions

The following table shows the names and functions of the input/output pins
Table 2.2.1 Pin Names and Functions (1/3)
Pin name
P00 to P07
Number
of Pin
8
A0 to A7
P50 to P57
8
8
1
P71
1
1
I/O
I/O
I/O
I/O
Address: Address bus 0 to 7

Port 5: I/O port Input or output specifiable in units of bits
Port 70: I/O port (Schmitt input, with pull-up register)
Read: Outputs strobe signal for read external memory.

Write enable for SRAM: Strobe signal for wiritng data.
Data enable for SRAM on pins D0 to D7
Data enable for SRAM on pins D8 to D15
Input
Port 74: Input port (Schmitt input)
Input
USBOC
8-bit timer 0 input: Input pin of 8-bit timer TMRA0
I/O
Input
USBPON
I/O
Port 75: I/O port (Schmitt input)

USBOC Input
Port 76: I/O port (Schmitt input)
Output
1
X1USB
P80
I/O
Output
TA0IN
P77
I/O
Output
1
SRLUB
P76
Output
SRLLB
P75
Data: Data bus 8 to 15
I/O
Output
SRWR
P74
Output
P70
RD
P73
Data: Data bus 0 to 7
I/O
Output
A16 to A23
P72
Output
A8 to A15
P60 to P67
I/O
I/O
D8 to D15
P40 to P47
Function
I/O
D0 to D7
P10 to P17
I/O
USBPON Output
I/O
Port 77: I/O port
Input
1
48MHz Clock Input for USB Host Controller
Output
Port 80: Output port
CS0
Output
Chip select 0: Outputs Low when address is within specified address area
TA1OUT
Output
8-bit timer 1 Output: Output pin of 8-bit timer TMRA0 or TMRA1
( BOOT Note)
Input
This pin sets single boot mode (only during reset).

(Note) The function of TMP92FD28
P82
P83
Port 82: Output port
Output
CS2
Output
I/O
Port 83: I/O port
CS3
Output
TA5OUT
WAIT
Output
Input
Wait: Signal used to request CPU bus wait
Input
Port C0: Input port (Schmitt input)
Input
Interrupt request pin0 : Interrupt request pin with programmable level/rising/falling edge
Input
Input
Interrupt request pin 1 : Interrupt request pin with programmable level/rising/falling edge
Input
INT2
Input
TB0IN0
Input
16-bit timer 0 input 0: Input of count/capture trigger in 16-bit timer TMRB0
TB1IN0
Input
16-bit timer 1 input 0: Input of count/capture trigger in 16-bit timer TMRB1
Input
Input
PC0
INT0
PC1
INT1
PC2
PC3
INT3
147
AVR 2650
harman/kardon
TMP92CD28
Pin name
PF0
Number
of Pin
I/O
Function
I/O
Output
Port F0: I/O port (Schmitt input)
I/O
Input
SCLK0
I/O
I/O
CTS0
Input
TXD0
PF1
RXD0
PF2
Serial 0 send data: Open drain output programmable

Serial 0 receive data
Serial 0 clock I/O
Serial 0 data send enable (Clear to send)
CLK
Output
Clock: System Clock output
TB0OUT0
Output
16-bit timer 0 output 0: Output pin of 16-bit timer TMRB0
I/O
Output
TXD1
SPDO
Output
SPI Data output
PF3
PF4
RXD1
I/O
Input
SPDI
Input
PF5
SCLK1
I/O
I/O
CTS1
Input
SPCLK
Output
PG0 to PG3
KI0 to KI3
Input
Serial 1 send data: Open drain output programmable

Serial 1 receive data
SPI Data input
Serial 1 clock I/O
Serial 1 data send enable (Clear to send)
SPI Clock output
Port G: Input port (Schmitt input)
Key input 0 to 7: Pin used of key-on wakeup 0 to 7
148
AVR 2650
harman/kardon
TMP92CD28
Pin name
PN1
Number of
1
SDA0
TA3OUT
PN2
Port N1: I/O port (Schmitt input, Open drain output)

Serial bus interface 0 send/receive data at I C mode
I/O

Serial bus interface 0 clock I/O data at I C mode
Input
1
8-bit timer 2 input: Input pin of 8-bit timer TMRA2
HSCLK
I/O
Port N3: I/O port (Schmitt input)
I/O
SCK1
Serial bus interface 1 clock I/O data at SIO mode
Output
1
SO1
I/O
Output
SDA1
I/O
HSSO
PN5
I/O
I/O
TA2IN
PN4
Function
Output
1
SCL0
PN3
I/O
I/O
Pin
Output
1
SI1
I/O
HSIO Clock output

Serial bus interface 1 send data at SIO mode
2
Serial bus interface 1 send/receive data at I C mode

HSIO Data output
Input
Serial bus interface 1 clock I/O data at I C mode
Input
HSIO Data input
AM0, AM1
Input
Operation mode:
X1 / X2
I/O
High-frequency oscillator connection I/O pins
XT1/XT2
I/O
Low-frequency oscillator circuit connection pin.
Fixed to AM1
1 and AM0
HSSI
Serial bus interface 1 receive data at SIO mode
I/O
SCL1
RESET
Input
PWE
Output
Reset: Intializes TMP92CD28 (Schmitt input, with pull-up register)
D+, D-
I/O
RVIN
Input
RVOUT1,
RVOUT2
DVCC3A
5
1
DVCC1A
DVCC1B
Power supply pin for peripheral I/O-A (Connect all DVCC3A pins to power supply pin.)
DVCC3B
DVSS
GND pins (0 V) (All DVSS pins shold be connected with GND(0V))
External power supply control output: Pin to control ON/OFF of external power supply. In
stand-by mode, outputs L level. In other than stand-by mode, outputs H level.
Data pin connected to USB.
Output
In case USB is not used, connect both pins to pull-up(DVCC3A) or pull-down resistor for
protect current flows it.
Power supply pin for Internal Regulator
1.5V output from Internal Regulator (Only Mask ROM Version)
Power supply pin for peripheral I/O-B (Connect all DVCC3B pins to power supply pin.)
Power supply pin for internal logic-A.
Power supply pin for internal logic-B.
149
AVR 2650
harman/kardon
KSZ8851SNL/SNLI
Single-Port Ethernet Controller
with SPI Interface
Rev. 2.0
General Description
The KSZ8851SNL is a single-chip Fast Ethernet controller
consisting of a 10/100 physical layer transceiver (PHY), a
MAC, and a Serial Peripheral Interface (SPI). The
KSZ8851SNL is designed to enable an Ethernet network
connectivity with any host micro-controller equipped with
SPI interface. The KSZ8851SNL offers the most costeffective solution for adding high-throughput Ethernet link
to traditional embedded systems with SPI interface.
The KSZ8851SNL is a single chip, mixed analog/digital
device offering Wake-on-LAN technology for effectively
addressing Fast Ethernet applications. It consists of a Fast
Ethernet MAC controller, SPI interface and incorporates a
unique dynamic memory pointer with 4-byte buffer
boundary and a fully utilizable 18KB for both TX (allocated
6KB) and RX (allocated 12KB) directions in host buffer
interface.
The KSZ8851SNL is designed to be fully compliant with
the appropriate IEEE 802.3 standards. An industrial
temperature-grade version of the KSZ8851SNL, the
KSZ8851SNLI is also available (see Ordering Information
section).
LinkMD
Physical signal transmission and reception are enhanced

through the use of analog circuitry, making the design
more efficient and allowing for lower-power consumption.
The KSZ8851SNL is designed using a low-power CMOS
process that features a single 3.3V power supply with
options for 1.8V, 2.5V or 3.3V VDD I/O. The device
includes an extensive feature set that offers management
information base (MIB) counters and a fast SPI interface
with clock speed up to 40MHz.
The KSZ8851SNL includes unique cable diagnostics
feature called LinkMD . This feature determines the length

of the cabling plant and also ascertains if there is an open
or short condition in the cable. Accompanying software
enables the cable length and cable conditions to be
conveniently displayed. In addition, the KSZ8851SNL
supports Hewlett Packard (HP) Auto-MDIX thereby
eliminating the need to differentiate between straight or
crossover cables in applications.
Functional Diagram
Figure 1. KSZ8851SNL/SNLI Functional Diagram

LinkMD is a registered trademark of Micrel, Inc.
Magic Packet is a trademark of Advanced Micro Devices, Inc.
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Product names used in this datasheet are for identification purposes

only and may be trademarks of their respective companies.
Micrel Inc. 2180 Fortune Drive San Jose, CA 95131 USA tel +1 ( ) 944-0800 fax + 1 (408) 474-1000 http://www.micrel.com
408
M9999-083109-2.0
August 2009
150
AVR 2650
harman/kardon
Micrel, Inc.
KSZ8851SNL/SNLI
Features
Additional Features
In addition to offering all of the features of a Layer 2

controller, the KSZ8851SNL offers:
Supports to add two-byte before frame header in order
for IP frame content with double word boundary
Micrel LinkMD cable diagnostic capabilities to

determine cable length, diagnose faulty cables, and
determine distance to fault
Wake-on-LAN functionality
Incorporates Magic Packet, wake-up frame, network
link state, and detection of energy signal technology
HP Auto MDI-X crossover with disable/enable option
Ability to transmit and receive frames up to 2000 bytes
Network Features
10BASE-T and 100BASE-TX physical layer support

Auto-negotiation: 10/100 Mbps full and half duplex
Adaptive equalizer
Baseline wander correction
Applications
Video/Audio Distribution Systems

Voice over IP (VoIP) and Analog Telephone Adapters
(ATA)
Building Automation
Home Base Control with Ethernet Connection
Industrial Control Sensor Devices (Temperature,
Pressure, Levels, and Valves)
Security, Motion Control and Surveillance Cameras
Markets
August 2009
Single 3.3V power supply with options for 1.8V, 2.5V

and 3.3V VDD I/O
Built-in integrated 3.3V or 2.5V to 1.8V low noise
regulator (LDO) for core and analog blocks
Enhanced power management feature with energy
detect mode and soft power-down mode to ensure lowpower dissipation during device idle periods
Comprehensive LED indicator support for link, activity
and 10/100 speed (2 LEDs)
User programmable
Low-power CMOS design
o
o
Commercial Temperature Range: 0 C to +70 C
o
o
Industrial Temperature Range: 40 C to +85 C
Available in 32-pin (5mm x 5mm) MLF package
Power Modes, Power Supplies, and Packaging
Integrated MAC and PHY Ethernet Controller fully

compliant with IEEE 802.3/802.3u standards
SPI Interface with clock speeds up to 40MHz for high
throughput applications
Supports 10BASE-T/100BASE-TX
Supports IEEE 802.3x full-duplex flow control and halfduplex backpressure collision flow control
Supports RXQ and TXQ FIFO DMA for fast data read
and write transfers
Supports IP Header (IPv4)/TCP/UDP/ICMP checksum
generation and checking
Supports IPv6 TCP/UDP/ICMP checksum generation
and checking
Automatic 32-bit CRC generation and checking
Supports simple command and data phases in SPI
cycle for RXQ/TXQ FIFO and registers read/write
Supports multiple data frames for TXQ FIFO and RXQ
FIFO without additional command phase
Supports flexible Byte (8-bit), Word (16-bit) and Double
word (32-bit) read/write access to internal registers
Larger internal memory with 12K Bytes for RX FIFO and
6K Bytes for TX FIFO. Programmable low, high and
overrun watermark for flow control in RX FIFO
Efficient architecture design with configurable host
interrupt schemes to minimize host CPU overhead and
utilization
Powerful and flexible address filtering scheme
Optional to use external serial EEPROM configuration
for MAC address
Single 25MHz reference clock for both PHY and MAC
HBM ESD Rating 6kV
Fast Ethernet
Embedded Ethernet
Industrial Ethernet
Embedded Systems
M9999-083109-2.0
151
AVR 2650
harman/kardon
Micrel, Inc.
KSZ8851SNL/SNLI
Pin Configuration
Figure 2. 32-Pin (5mm x 5mm) MLF
August 2009
M9999-083109-2.0
152
AVR 2650
harman/kardon
Micrel, Inc.
KSZ8851SNL/SNLI
Pin Description
Pin Number
Pin Name
Type
Pin Function
LED0
Opu
Programmable LED output to indicate PHY activity/status.

LED is ON when output is LOW; LED is OFF when output is HIGH.
1
LED indicators defined as follows:
Chip Global Control Register: CGCR bit [9]
0 (Default)
LED1 (pin 32)
100BT
ACT
LED0 (pin 1)
LINK/ACT
LINK
Link (up) = LED On; Activity = LED Blink; Link/Act = LED On/Blink;
Speed = LED On (100BASE-T); LED Off (10BASE-T)
2
PME
Opu
Power Management Event (default active low)

It is asserted (low or high depends on polarity set in PMECR register) when one of the
wake-on-LAN events is detected by KSZ8851SNL. The KSZ8851SNL is requesting the
system to wake up from low power mode.
INTRN
Opu
Interrupt Not
An active low signal to host CPU to indicate an interrupt status bit is set. This pin needs
an external 4.7K pull-up resistor.
DGND
Gnd
VDD_CO1.8
Digital IO ground.
1.8V regulator output . This 1.8V output pin provides power to pins 9 (VDD_A1.8) and 23
(VDD_D1.8) for core VDD supply.
If VDD_IO is set for 1.8V then this pin should be left floating, pins 9 (VDDA_1.8) and 23
(VDD_D1.8) will be sourced by the external 1.8V supply that is tied to pins 25 and 30
(VDD_IO) with appropriate filtering.
EED_IO
Ipd/O
In/Out Data from/to external EEPROM

Config Mode: The pull-up/pull-down value is latched as with/without EEPROM during
power-up / reset. See Strapping Options section for details.
EESK
Opd
EEPROM Serial Clock
A 4 s (OBCR[1:0]=11 on-chip bus speed @ 25MHz) or 800ns (OBCR[1:0]=00 on-chip

bus speed @ 125 MHz) serial output clock to load configuration data from the serial
EEPROM.
8
AGND
Gnd
Analog ground.
VDD_A1.8
10
EECS
Opd
11
RXP
I/O
Physical receive (MDI) or transmit (MDIX) signal (+ differential).
12
RXM
I/O
Physical receive (MDI) or transmit (MDIX) signal ( differential).
13
AGND
Gnd
Analog ground.
14
TXP
I/O
Physical transmit (MDI) or receive (MDIX) signal (+ differential).
15
TXM
I/O
16
VDD_A3.3
17
ISET
1.8V analog power supply from VDD_CO1.8 (pin 5) with appropriate filtering. If VDD_IO is
1.8V, this pin must be supplied power from the same source as pins 25 and 30 (VDD_IO)
with appropriate filtering.
EEPROM Chip Select
This signal is used to select an external EEPROM device.
Physical transmit (MDI) or receive (MDIX) signal ( differential).

3.3V analog VDD input power supply with well decoupling capacitors.
Set physical transmits output current.
Pull-down this pin with a 3.01K 1% resistor to ground.
18
AGND
Gnd
Analog ground.
19
RSTN
Ipu
Reset Not.
August 2009
M9999-083109-2.0
153
AVR 2650
harman/kardon
Micrel, Inc.
Pin Number
KSZ8851SNL/SNLI
Pin Name
Type
Pin Function
Hardware reset pin (active Low). This reset input must be held low for a minimum of 10ms
after stable supply voltage 3.3V.
20
21
X1
X2
25MHz crystal or oscillator clock connection.
Pins (X1, X2) connect to a crystal. If an oscillator is used, X1 connects to a 3.3V tolerant
oscillator and X2 is a no connect.
Note: Clock requirement is +/- 50ppm for either crystal or oscillator.
22
DGND
Gnd
23
VDD_D1.8
Digital IO ground
24
DGND
Gnd
25
VDD_IO
26
CSN
Ipu
27
SO
SPI slave mode: Serial data out for SPI interface. This SO is tri-stated output when CSN
is negated and this pin must have external 4.7K pull-up to keep the SO line high while the
driver is tri-stated.
28
SCLK
SPI slave mode: Serial clock input for SPI interface. This clock speed can run up to
40MHz.
29
DGND
Gnd
30
VDD_IO
31
SI
Ipd
SPI slave mode: Serial data in for SPI interface.
32
LED1
Opu
Programmable LED1 output to indicate PHY activity/status (see LED0 description at pin1)
1.8V digital power supply from VDD_CO1.8 (pin 5) with appropriate filtering. If VDD_IO is
1.8V, this pin must be supplied power from the same source as pins 25 and 30 (VDD_IO)
with appropriate filtering.
Digital IO ground
3.3V, 2.5V or 1.8V digital VDD input power supply for IO with well decoupling capacitors.
SPI slave mode: Chip Select Not
Active low input pin for SPI interface.
Digital IO ground
3.3V, 2.5V or 1.8V digital VDD input power supply for IO with well decoupling capacitors.
Legend:
P = Power supply Gnd = Ground
I/O = Bi-directional I = Input O = Output.
Ipd = Input with internal pull-down (58K +/-30%).
Ipu = Input with internal pull-up (58K +/-30%).
Opd = Output with internal pull-down (58K +/-30%).
Opu = Output with internal pull-up (58K +/-30%).
Ipu/O = Input with internal pull-up (58K +/-30%) during power-up/reset; output pin otherwise.
Ipd/O = Input with internal pull-down (58K +/-30%) during power-up/reset; output pin otherwise.
Strapping Options
Pin Number
Pin Name
Type
EED_IO
Ipd/O
Pin Function
EEPROM select:
Pull-up = EEPROM present
Floating (NC) or Pull-down = EEPROM not present (default)
During power-up / reset, this pin value is latched into register CCR, bit 9
Note: Ipd/O = Input with internal pull-down (58K +/-30%) during power-up/reset; output pin otherwise.
Pin strap-ins are latched during power-up or reset.
August 2009
M9999-083109-2.0
154
AVR 2650
harman/kardon
155
AVR 2650
harman/kardon
1 Overview and Features
TMPM333
32-bit RISC Microcontroller TX03 Series
TMPM333FDFG
TMPM333FYFG
TMPM333FWFG
Overview and Features
The TX03 series is a 32-bit RISC microcontroller series with an ARM CortexTM-M3 microcontroller
core.
Features of the TMPM333FDFG/FYFG/FWFG are as follows:
1.1 Features
ARM Cortex-M3 microcontroller core
1) Improved code efficiency has been realized through the use of Thumb -2 instruction
New 16-bit Thumb instructions for improved program flow
New 32-bit Thumb instructions for improved performance
Auto-switching between 32-bit instruction and 16-bit instruction is executed by compiler.
2) Both high performance and low power consumption have been achieved.
-High performance
A 32-bit multiplication (3232=32 bit) can be executed with one clock.
Division takes between 2 and 12 cycles depending on dividend and devisor
-Low power consumption
Optimized design using a low power consumption library
Standby function that stops the operation of the microcontroller core
3) High-speed interrupt response suitable for real-time control
An interruptible long instruction.
(1)
1.
Stack push automatically handled by hardware.
156
AVR 2650
harman/kardon
TMPM333
(2)
On Chip program memory and data memory

Product name
On chip RAM
TMPM333FDFG
512Kbyte
32Kbyte
TMPM333FYFG
256Kbyte
16Kbyte
TMPM333FWFG
(3)
On chip Flash ROM
128Kbyte
8Kbyte
16-bit timer
16-bit interval timer mode
16-bit event counter mode
16-bit PPG output
: 10 channels
Input capture function
(4)
Real time clock (RTC)

: 1 channel
Clock (hour, minute and second)
Calendar (Month, week, date and leap year)
Time correction
or
30 seconds (by software)
Alarm (Alarm output)
Alarm interrupt
(5)
Watchdog timer
26 cycles of binary counter
Watchdog timer out
(6)
General-purpose serial interface

: 3 channels
Either UART mode or synchronous mode can be selected (4byte FIFO equipped)
(7)
Serial bus interface

: 3 channels
Either I2C bus mode or synchronous mode can be selected.
(8)
10-bit A/D converter

Start by an internal or external timer trigger
Fixed channel/scan mode
Single/repeat mode
AD monitoring 2ch
Conversion speed 1.15usec(@fsys = 40MHz)
(9)
Interrupt source
Internal: 38 factorsThe order of precedence can be set over 7 levels (except the watchdog
timer interrupt).
: 1 channel
: 12 channels
External: 8 factorsThe order of precedence can be set over 7 levels.
(10) Input/ output ports

79 pins
157
AVR 2650
harman/kardon
1 Overview and Features
TMPM333
(11) Standby mode

Standby modes
:IDLE, SLOW, SLEEP, STOP
Sub clock operation(32.768kHz)
:SLOW, SLEEP
(12) Clock generator

On-chip PLL (quadrupled)
Clock gear function: The high-speed clock can be divided into 1/1, 1/2, 1/4 or 1/8.
(13) Endian
Little endian
(14) Maximum operating frequency

40MHz
(15) Operating voltage range

2.7V~3.6V (with on-chip regulator)
(16) Temperature range

-20~85 degrees (except during Flash writing/ erasing)
0~70 degrees (during Flash writing/ erasing)
(17) Package
LQFP100-P-1414-0.5H (14mm
14mm, 0.5mm pitch)
158
AVR 2650
harman/kardon
TMPM333
1.2 Block Diagram
I/F
RAM
I/F
D-Code
Debug
I/F
BOOT
ROM
I-Code
System
AHB-Bus-Matrix
Cortex-M3
CPU
FLASH
NVIC
Bus Bridge
CG
PORT A~K
SIO (3ch)
TMRB (10ch)
IO-Bus
I2C (3ch)
WDT
RTC
ADC (12ch)
Fig. 1-1 TMPM333 FDFG/FYFG/FWFG Block Diagram
159
AVR 2650
harman/kardon
2 Pin Layout and Pin Functions
TMPM333
Pin Layout and Pin Functions

This chapter describes the pin layout, pin names and pin functions of TMPM333FDFG/
TMPM333FYFG/ TMPM333FWFG.
2.1
Pin Layout (Top view)
80
85
90
95
75
5
70
10
TMPM333FDFG
TMPM333FYFG
TMPM333FWFG
15
65
Top View
60
20
50
45
40
35
25
30
55
SDA0/ SO0/ PG0

SCL0/ SI0/ PG1
SCK0/ PG2
PB3
BOOT/ TB0IN0/ PH0
TB0IN1/ PH1
TB1IN0/ PH2
TXD2/ PF0
RXD2/ PF1
CTS2/ SCLK2/ PF2
TB1IN1/ PH3
PB4
TB0OUT/ PI0
INT6/ PJ6
TB1OUT/ PI1
PB5
TB2OUT/ PI2
PB6
SDA1/ SO1/ PF4
SCL1/ SI1/ PF5
SCK1/ PF6
PB7
TB3OUT/ PI3
INT1/ PJ1
PK0
AN10/ PD6
AN11/ PD7
AVSS
VREFH
AVCC
INT4/ PG3
TB9OUT/ PK2
TB7OUT/ PJ5
TB2IN0/ PH4
TB2IN1/ PH5
TB8OUT/ PG7
TEST2
DVSS
DVCC
SDA2/ SO2/ PG4
SCL2/ SI2/ PG5
SCK2/ PG6
TEST1
INT5/ PF7
TXD0/ PE0
RXD0/ PE1
CTS0/ SCLK0/ PE2
TXD1/ PE4
RXD1/ PE5
CTS1/ SCLK1/ PE6
100
PD5 /AN9
PD4 /AN8
PD3 /AN7 /TB6IN1
PD2 /AN6 /TB6IN0
PD1 /AN5 /TB5IN1
PD0 /AN4 /TB5IN0
PC3 /AN3
PC2 /AN2
PC1 /AN1
PC0 /AN0
TEST4
PE3
PJ4 /TB6OUT
PJ3 /INT3
PJ2 /INT2
PH7 /TB3IN1
PH6 /TB3IN0
PI7 /TB4IN1
RESET
MODE
NMI
PI6 /TB4IN0
XT2
XT1
REGVCC
Fig.2-1 shows the pin layout of TMPM333FDFG/TMPM333FYFG/TMPM333FWF.
Fig.2-1 Pin Layout (LQFP100)
160
REGVSS
X1
CVSS
X2
CVCC
PJ0 /INT0
PA7
PA6 /TRACEDATA3
PA5 /TRACEDATA2
PA4 /TRACEDATA1
PA3 /TRACEDATA0
PA2 /TRACECLK
DVSS
DVCC
PF3
PB2 / TRST
PB1 /TDI
PJ7 /INT7
TEST3
PA1 /TCK /SWCLK
PA0 /TMS /SWDIO
PB0 /TDO /SWV
PI5 /TB5OUT
PI4 /TB4OUT
PK1 /SCOUT /ALARM
AVR 2650
harman/kardon
t
TMPM333
Table2-1 Pin Numbers and Names (1/2)

Pin
No.
1
2
3
4
Pin name
PD6, AN10
PD7, AN11
AVSS
VREFH
Pin
No.
26
27
28
29
AVCC
30
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PG3, INT4
PK2, TB9OUT
PJ5, TB7OUT
PH4, TB2IN0
PH5, TB2IN1
PG7, TB8OUT
TEST2
DVSS
DVCC
PG4, SO2, SDA2
PG5, SI2, SCL2
PG6, SCK2
TEST1
PF7, INT5
PE0, TXD0
PE1, RXD0
PE2, SCLK0, CTS0
PE4, TXD1
PE5, RXD1
PE6, SCLK1, CTS1
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
161
Pin name
PG0, SO0, SDA0
PG1, SI0, SCL0
PG2, SCK0
PB3
PH0, TB0IN0, BOOT
PH1, TB0IN1
PH2, TB1IN0
PF0, TXD2
PF1, RXD2
PF2, SCLK2, CTS2
PH3, TB1IN1
PB4
PI0, TB0OUT
PJ6, INT6
PI1, TB1OUT
PB5
PI2, TB2OUT
PB6
PF4, SO1, SDA1
PF5, SI1, SCL1
PF6, SCK1
PB7
PI3, TB3OUT
PJ1, INT1
PK0,
AVR 2650
harman/kardon
Under development
TMPM333
Table2-1 Pin Numbers and Names (2/2)

Pin
No.
Pin name
Pin
No.
Pin name
76
REGVCC
52
53
54
55
56
PK1, SCOUT, ALARM

PI4, TB4OUT
PI5, TB5OUT
PB0, TDO, SWV
PA0, TMS, SWDIO
PA1, TCK, SWCLK
77
78
79
80
81
XT1
XT2
PI6, TB4IN0
57
TEST3
82
RESET
58
59
PJ7, INT7
PB1, TDI
83
84
PI7, TB4IN1
PH6, TB3IN0
60
PB2, TRST
PF3
DVCC
DVSS
PA2, TRACECLK
PA3, TRACEDATA0
PA4, TRACEDATA1
PA5, TRACEDATA2
PA6, TRACEDATA3
PA7
PJ0, INT0
CVCC
X2
CVSS
X1
REGVSS
85
PH7, TB3IN1
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
PJ2, INT2
PJ3, INT3
PJ4, TB6OUT
PE3
TEST4
PC0, AN0
PC1, AN1
PC2, AN2
PC3, AN3
PD0, AN4, TB5IN0
PD1, AN5, TB5IN1
PD2, AN6, TB6IN0
PD3, AN7, TB6IN1
PD4, AN8
PD5, AN9
51
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
162
NMI
MODE
AVR 2650
harman/kardon
Under development
2.2
TMPM333
Pin names and Functions
Table2-2 and Table2-3 sort the input and output pins of the TMPM333FDFG/ TMPM333FYFG/
TMPM333FWFG by pin or port. Each table includes alternate pin names and functions for multi-function pins.
2.2.1
Sorted by Pin
Table2-2 Pin Names and Functions Sorted by Pin (1/5)
PG3
INT4
PK2
TB9OUT
PJ5
TB7OUT
PH4
TB2IN0
PH5
TB2IN1
PG7
TB8OUT
TEST2
DVSS
DVCC
PG4
I/O
I
I/O
O
I/O
I
I/O
I
I/O
I
I/O
O
I/O
SDA2/
SO2
PG5
I/O
O
I/O
SCL2/
SI2
PG6
SCK2
I/O
I
I/O
I/O
6
7
8
Function
9
10
11
Test
PS
12
13
14
15
Function
16
17
Test
18
TEST1
Function
19
PF7
INT5
I/O
I
I/O port
Interrupt request pin
163
Pull up
w/ noise filter
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
AVCC
w/ noise filter
Pull up
VREFH
PS
Pull up
AVSS
Programm
able Open
Drain
Output
Function
Input port
Analog input
Input port
Analog input
A/D converter: GND pin (0V)
Tie AVSS to power supply even if the A/D
converter is not used.
Supplying the A/D converter with a
reference power supply.
Tie VREFH to power supply even if the
A/D converter is not used.
Supplying the A/D converter with a power
supply. Tie AVCC to power supply even if
the A/D converter is not used.
I/O port
I/O port
Timer B output
I/O port
Timer B output
I/O port
Inputting the timer B capture trigger
I/O port
I/O port
Timer B output
TEST pin: Not connected.
GND pin
Power supply pin
I/O port
If the serial bus interface operates
-in the I2C mode : data pin
-in the SIO mode: data pin
I/O port
-in the I2C mode : clock pin
I/O port
Inputting and outputting a clock if the
serial bus interface operates in the SIO
mode.
Schmitt
trigger
I
I
I
I
Programma
ble Pull up/
Pull down
PD6
AN10
PD7
AN11
Function
Input/
Output
Pin Name
# of
Pins
Type
AVR 2650
harman/kardon
Under development
TMPM333
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
164
w/ noise filter
39
Pull up
38
37
Pull up
36
35
Pull up
Function
Pull up
34
33
32
Pull up
I/O
I
I/O
I
I/O
O
I/O
I
I/O
I
I
I/O
I
I/O
I/O
O
I/O
I
PH1
TB0IN1
PH2
TB1IN0
PF0
TXD2
PF1
RXD2
PF2
SCLK2
CTS2
PH3
TB1IN1
PB4
PI0
TB0OUT
PJ6
INT6
31
Pull up
BOOT
I/O
I
I
Pull up
PH0
TB0IN0
Pull up
Function/
Control
Pull up
30
28
Pull up
I/O
27
PB3
26
Pull up
29
25
Function
Pull up
I/O
I
I/O
I/O
24
Pull up
SCL0/
SI0
PG2
SCK0
23
I/O
O
I/O
22
Pull up
SDA0/
SO0
PG1
21
I/O port
Sending serial data
I/O port
Receiving serial data
I/O port
Serial clock input/ output
Handshake input pin
I/O port
Sending serial data
I/O port
I/O port
Handshake input pin
I/O port
I/O port
I/O port
mode.
I/O port
I/O port
Setting a single boot mode: This pin
goes into single boot mode by sampling
"L" at the rise of a reset signal.
I/O port
I/O port
I/O port
Sending serial data
I/O port
I/O port
Handshake input pin
I/O port
I/O port
I/O port
Timer B output
I/O port
I/O
O
I/O
I
I/O
I
I
I/O
O
I/O
I
I/O
I
I
I/O
Schmitt
trigger
PE0
TXD0
PE1
RXD0
PE2
SCLK0
CTS0
PE4
TXD1
PE5
RXD1
PE6
SCLK1
CTS1
PG0
20
Function
Programma
ble Open
Drain
Output
Programm
able
Pull-up/
Pull down
Input/
Pin Name
Output
Type
# of
Pins
AVR 2650
harman/kardon
Under development
TMPM333
50 PK0
I/O
I/O port
PS
w/ noise filter
I/O port
System clock output
Alarm output
I/O port
Timer B output
I/O port
Timer B output
I/O port
Debug pin
I/O port
Debug pin
I/O port
Debug pin
I/O port
I/O port
Debug pin
I/O port
Debug pin
I/O port
Power supply pin
GND pin
165
(Note 4)
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
w/ noise filter
Pull up
Pull up
-
Function
Function/
Debug
Function
PK1
I/O
O
51 SCOUT
O
ALARM
PI4
I/O
52
TB4OUT
O
PI5
I/O
53
TB5OUT
O
PB0
I/O
54
TDO/SWV O
PA0
I/O
55
TMS/SWDIO I/O
PA1
I/O
56 TCK/
I
SWCLK
57 TEST3
PJ7
I/O
58
INT7
I
PB1
I/O
59
TDI
I
PB2
I/O
60
I
TRST
61 PF3
I/O
62 DVCC
63 DVSS
-
Test
I/O
I
I/O
I/O
Function/
Debug
46
SCL1/
SI1
PF6
SCK1
Function
I/O
O
I/O
45
SDA1/
SO1
PF5
I/O
I/O
O
I/O
I
44
I/O
O
I/O
I/O
O
I/O
I/O
Programmab
le Open
Drain
Output
47 PB7
PI3
48
TB3OUT
PJ1
49
INT1
Pull up
I/O port
Timer B output
Pull up
I/O port
I/O port
Pull up
Timer B output
Pull up
I/O port
I/O port
Pull up
I/O port
Pull up
I/O port
Pull up
mode.
Pull up
I/O port
I/O port
Pull up
Timer B output
I/O port
Pull up
PI1
TB1OUT
41 PB5
PI2
42
TB2OUT
43 PB6
PF4
40
Schmitt
trigger
Programmab
le Pull-up/
Pull down
Function
Input/
Output
Pin Name
# of
Pins
Type
Pull up
AVR 2650
harman/kardon
Under development
TMPM333
I/O port
PJ0
INT0
CVCC
X2
CVSS
X1
REGVSS
REGVCC
XT1
XT2
PI6
TB4IN0
I/O
I
O
I
I
O
I/O
I
I/O port
Power supply pin
Connected to a high-speed oscillator.
GND pin
GND pin
Power supply pin
Connected to a low-speed oscillator.
I/O port
NMI
Non-maskable interrupt
81 MODE
Mode pin: Tied to GND pin
Reset input pin
I/O
I
I/O
I
I/O
I
I/O
I
I/O port
I/O port
I/O port
I/O port
Clock
PS
Clock
79
Function
80
Control
RESET
PI7
TB4IN0
PH6
84
TB3IN0
PH7
85
TB3IN1
PJ2
86
INT2
83
Function
Pull up
Pull up
Pull up
-
w/ noise filter
Tied to
Pull up
w/ noise filter
Pull up
Pull up
Pull up
Pull up
87
PJ3
INT3
I/O
I
I/O port
Pull up
88
PJ4
TB6OUT
I/O
O
I/O port
Timer B output
89 PE3
I/O
I/O port
90 TEST4
w/ noise filter
Pull up
Pull up
166
w/ noise filter
Test
w/ noise filter
PS
Clock
71
72
73
74
75
76
77
78
PS
70
69 PA7
Function
PA6
TRACEDATA3
68
PA5
TRACEDATA2
67
PA4
TRACEDATA1
66
Pull up
82
Function/
Debug
PA3
TRACEDATA0
Pull up
I/O
65
Programmab
le Open
Drain
Output
Pull up
I/O port
Debug pin
I/O port
Debug pin
I/O port
Debug pin
I/O port
Debug pin
I/O port
Debug pin
TRACECLK
Schmitt
trigger
Pull up
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
64
Programma
ble Pull-up/
Pull down
Pull up
Function
PA2
Input/
Output
Pin Name
# of
Pins
Type
AVR 2650
harman/kardon
Under development
TMPM333

Type
# of
Pins
PC0
AN0
PC1
92
AN1
PC2
93
AN2
PC3
94
AN3
PD0
95 AN4
TB5IN0
PD1
96 AN5
TB5IN1
PD2
97 AN6
TB6IN0
PD3
98 AN7
TB6IN1
PD4
99
AN8
PD5
100
AN9
91
Function
(Note 1)
(Note 2)
(Note 3)
(Note 4)
(Note 5)
Pin Name
Input/
Output
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Function
Input port
Analog input
Input port
Analog input
Input port
Analog input
Input port
Analog input
Input port
Analog input
Input port
Analog input
Input port
Analog input
Input port
Analog input
Inputting the timer B capture trigger of
Input port
Analog input
Input port
Analog input
Programma
ble Pull-up/
Pull down
Schmitt
trigger
Programma
ble Open
Drain
Output
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
TEST1 through 4 must be left unconnected.

Be sure to tie MODE to GND.
Tie VREFH/ AVCC to power supply and AVSS to GND even if the A/D converter is not used.
Nch open drain port.
The noise elimination width of the noise filter is approximately 30 ns under typical
conditions.
167
AVR 2650
harman/kardon
TC74VHC153F/FN/FT/FK
TOSHIBA CMOS Digital Integrated Circuit
Silicon Monolithic
TC74VHC153F,TC74VHC153FN,TC74VHC153FT,TC74VHC153FK
Dual 4-Channel Multiplexer
The TC74VHC153 is an advanced high speed CMOS DUAL
4-CHANNEL MULTIPLEXERs fabricated with silicon gate
C2MOS technology.
It achieves the high speed operation similar to equivalent
Bipolar Schottky TTL while maintaining the CMOS low power
dissipation.
Each of these data (1C0-1C3, 2C0-2C3) is selected by the two
address inputs A and B.
Separate strobe inputs ( 1G , 2G ) are provided for each of the
two four-line sections.
The strobe input ( G ) can be used to inhibit the data output;
the output is fixed in low level while the strobe input is held
high.
An input protection circuit ensures that 0 to 5.5 V can be
applied to the input pins without regard to the supply voltage.
This device can be used to interface 5 V to 3 V systems and two
supply systems such as battery back up. This circuit prevents
device destruction due to mismatched supply and input voltages.
Note: xxxFN (JEDEC SOP) is not available in

Japan.
TC74VHC153F
TC74VHC153FN
Features
TC74VHC153FT
High speed: tpd = 5.0 ns (typ.) at VCC = 5 V
Low power dissipation: ICC = 4 A (max) at Ta = 25C
High noise immunity: VNIH = VNIL = 28% VCC (min)
Power down protection is provided on all inputs.
Balanced propagation delays: tpLH tpHL
Wide operating voltage range: VCC (opr) = 2 to 5.5 V
Pin and function compatible with 74ALS153

TC74VHC153FK
Weight
SOP16-P-300-1.27A
SOL16-P-150-1.27
TSSOP16-P-0044-0.65A
VSSOP16-P-0030-0.50
168
: 0.18 g (typ.)
: 0.13 g (typ.)
: 0.06 g (typ.)
: 0.02 g (typ.)
AVR 2650
harman/kardon
Pin Assignment
IEC Logic Symbol
(14)
0
1
1G
(1)
EN
(6)
1C1
(5)
1C2
(4)
1C3
(3)
2G
(15)
2C0
(10)
2C1
(11)
2C2
(12)
2C3
(13)
VCC
16
(2)
1C0
1G
15
14
0
3
2G
1C3
1C2
1C1
1C0
1Y
GND
2C3
13
4
5
12
2C2
2C1
11
2C0
10
2Y
8
(top view)
Truth Table
Select Inputs
Data Inputs
Strobe
Output
C0
C1
C2
C3
X: Dont care
169
MUX
(7)
1Y
(9)
2Y
AVR 2650
harman/kardon
System Diagram
A
14
S0
S0
S1
S1
B
2
S2
S2
S3
S3
1C0
1Y
S0
1C1
5
S1
1C2
4
S2
1C3
3
S3
1G
2C0
2C1
2C2
2C3
2G
10
11
12
Same as above block
13
15
170
2Y
AVR 2650
harman/kardon
CS49DV8C Data Sheet

FEATURES
32-bit Post-Processor Audio DSP supports Multichannel
Dolby Volume
Programmable through DSP Composer
CS49DV8, supports up to 7.1 Channels of Dolby Volume
processing at 48 kHz, 44.1 kHz or 32 kHz.
Input Configurable for all input/output digital audio types

(I2S, LJ/RJ, and TDM)
32-bit data path delivers uncompromised dynamic range
192 kHz capable integrated S/PDIF transmitter
DAO can operate in master or slave mode (SCLK &
LRCLK)
Integrated Clock Manager/PLL
Capable of operating from a wide variety of external
crystals or external oscillators
Input Fs Auto Detection, Reporting and Handling
Sample rate conversion.
Master & Slave Host Boot Capability via Serial Interface
SPI interface capable of running up to 25 MHz during run
time
1.8V Core and a 3.3V I/O that is tolerant to 5V input
32-bit Dual Audio DSP Engine

featuring Multichannel Dolby Volume
The new CS49DV8C is the fastest time-to-market, massproduction ready Multichannel Dolby Volume solution available.
The target applications for the CS49DV8C DSP are:
Soundbars
DTVs with Integrated Soundbars
HDTV Stands/Furniture with Integrated Soundbars
Automotive Head Units
Automotive Outboard Amplifiers
Blu-ray Disc & DVD Receivers / HTiBs
All of these applications and many more that use volume control
and are subject to playback from sources that do not have consistent volume levels will benefit from the CS49DV8C Dolby Volume
solution.
See page 27 for ordering information.
Serial
Control 1
Serial
Control 2
UART
GPIO
8 Ch. Audio In
STC
D
M
A
32-bit
DSP A
S/PDIF
S/PDIF
Debug
32-bit
DSP B
TMR1
TMR2
8 Ch PCM
Audio Out
Ext. Memory Controller
Preliminary Product Information
PLL
This document contains information for a new product.

Cirrus Logic reserves the right to modify this product without notice.
Copyright 2008 Cirrus Logic (All Rights Reserved)

http://www.cirrus.com
171
SEPT 08
DS868PP2
AVR 2650
harman/kardon
CS49DV8C Data Sheet

32-bit Audio DSP Family
8. Device Pin-Out Diagram
GPIO38, PCP_WR# / DS#, SCP2_CLK
SD_A10, EXT_A10
SD_BA0, EXT_A13
SD_BA1, EXT_A14
105 GNDIO5
SD_WE#
SD_CAS#
SD_RAS#
EXT_A15
110 SD_CS#
VDD5
EXT_A16
EXT_A17
EXT_A18
115 GND5
EXT_A19
EXT_OE#
EXT_CS1#
120 VDDIO6
GNDIO6
RESET#
GPIO33, SCP1_MOSI
GPIO34, SCP1__MISO / SDA
GPIO35, SCP1_CLK
125 VDD6
GND6
GPIO37, SCP1_BSY#, PCP_BSY#
8.1 128-Pin LQFP Pin-Out Diagram
SD_A0, EXT_A0
GPIO11, PCP_A3, AS#, SCP2_MISO / SDA
SD_A1, EXT_A1
100 VDDIO5
GPIO10, PCP_A2 / A10, SCP2_MOSI
SD_A2, EXT_A2
GPOI9, SCP1_IRQ#
GPIO8, PCP_IRQ#, SCP2_IRQ#
GND4
SD_A3, EXT_A3
GPIO7, SCP1_CS#, IOWAIT
SD_A4, EXT_A4
GPIO6, PCP_CS#, SCP2_CS#
95 VDD4
VDDIO7
EXT_CS2#
GNDIO7
SD_A5, EXT_A5
GPIO3, DDAC 10
GNDIO4
GPIO2, UART_TXD
VDD7
SD_A6, EXT_A6
GPIO1, UART_RXD
90 SD_A7, EXT_A7
VDDIO4
GPIO0, UART_CLK
SD_A8, EXT_A8
GND7 15
SD_A9, EXT_A9
XTAL_OUT
GND3
XTI
85 SD_A11, EXT_A11
XTO
SD_A12, EXT_A12
128-Pin LQFP
GNDA
PLL_REF_RES 20
VDD3
SD_CLKEN
VDDA (3.3V)
SD_CLKIN
VDD8
80 SD_CLKOUT
GPIO14, DAI1_DATA3, TM3, DSD3
SD_DQM1
SD_D8, EXT_D8
GND8 25
SD_D9, EXT_D9
GNDIO3
DAI1_DATA0, TM0, DSD0
75 SD_D10, EXT_D10
VDDIO8
SD_D11, EXT_D11
DAI1_SCLK, DSD-CLK
VDDIO3
DAI1_LRCLK, DSD4 30
SD_D12, EXT_D12
GNDIO8
SD_D13, EXT_D13
GPIO42, BDI_REQ# , DAI2_LRCLK, PCP_IRQ# / BSY#
70 SD_D14, EXT_D14
GPIO43, BDI_CLK, DAI2_SCLK
SD_D15, EXT_D15
BDI_DATA, DAI2_DATA, DSD5
SD_D0, EXT_D0
GPIO26, DAO2_DATA3 / XMTB/UART_TX_EN 35
GNDIO2
DBDA
EXT_WE#
DBCK
65 SD_D1, EXT_D1
SD_D2, EXT_D2
SD_D3, EXT_D3
VDDIO2
SD_D4, EXT_D4
SD_D5, EXT_D5 60
SD_D6, EXT_D6
SD_D7, EXT_D7
SD_DQM0
GND2
VDD2 55
GNDIO1
DAO1_LRCLK
DAO1_SCLK
DAO1_DATA0, HS0
VDDIO1 50
GPIO15, DAO1_DATA1, HS1
GND1 45
GPIO23,
DAO2_LRCLK
GPIO17, DAO1_DATA3 / XMTA
GPIO22, DAO2_SCLK
VDD1
TEST
DAO_MCLK 40
GPIO20, DAO2_DATA2, EE_CS#
Figure 15. 128-Pin LQFP Pin-Out

28
Copyright 2008 Cirrus Logic, Inc.
172
DS868PP2
AVR 2650
harman/kardon
TC74HC151AP/AF/AFN
Silicon Monolithic
TC74HC151AP,TC74HC151AF,TC74HC151AFN
8-Channel Multiplexer
The TC74HC151A is a high speed CMOS 8-CHANNEL
MULTIPLEXER fabricated with silicon gate C2MOS technology.
It achieves the high speed operation similar to equivalent
LSTTL while maintaining the CMOS low power dissipation.
One of eight date input signals (D0-D7) is selected by decoding
of the three-bit address input (A, B, C). The selected data appears
on two outputs: non-inverting (Y) and inverting (W).
The strobe input provides two output conditions; a low level on
the strobe input transfers the selected data to the outputs. A high
level on the strobe input sets the Y output low and the W output
high without regard to the data or select input conditions.
All inputs are equipped with protection circuits against static
discharge or transient excess voltage.
Note: xxxFN (JEDEC SOP) is not available in

Japan.
TC74HC151AP
TC74HC151AF
Features
High speed: tpd = 15 ns (typ.) at VCC = 5 V
Low power dissipation: ICC = 4 A (max) at Ta = 25C
High noise immunity: VNIH = VNIL = 28% VCC (min)
Output drive capability: 10 LSTTL loads
Symmetrical output impedance: |IOH| = IOL = 4 mA (min)

Balanced propagation delays: tpLH tpHL
Wide operating voltage range: VCC (opr) = 2 to 6 V
TC74HC151AFN
Pin and function compatible with 74LS151
Pin Assignment
Weight
DIP16-P-300-2.54A
SOP16-P-300-1.27A
SOL16-P-150-1.27
173
: 1.00 g (typ.)
: 0.18 g (typ.)
: 0.13 g (typ.)
AVR 2650
harman/kardon
Sound Processors for Home Theater Systems
2ch
Electronic Volume
No.10081EAT03
BD3812F
Description
BD3812F is an electronic volume having volume, gain amplifier functions necessary for applications in AV receivers, home
theatre systems, min-component systems and so forth. Having a chip select terminal, it can be controlled until 4 chips with
common bus line.
Features
1) Residual noise : 1.2Vrms {dynamic range : 131dB (IHF-A)}
2) 2ch independent volume (0 to -103dB, MUTE 1dB/step)
3) 8ch at maximum available in combination of any of BD3811K1, BD3813KS, BD3814FV, BD3815KS (6ch volume)
in common bus line
4) It can be controlled until 4 chips with common bus line at the same time
5) Maximum output voltage : 4.2Vrms (Vcc=7, VEE=-7V, RL=10k )
6) 2-line serial control (for both 3.3V and 5V)
7) Built-in Output gain amplifier for adjustment of output signal voltage (0, 6 to 18dB, 2dB/step)
8) Output mute controllable by serial data and external control terminal
Applications
AV receivers, home theater systems, mini-component systems, etc.
Symbol
Ratings
Unit
Powewr supply voltage
VCC
VEE
7.5 *1
-7.5
Input signal voltage
VIN
VCC+0.3 to VEE-0.3
Power dissipation
Pd
450*2
mW
Topr
Storage temperature range
Tastg
Even in the specified range of Power Supply Voltage, applying voltage only to the VCC side may
cause an excessive current to give a permanent damage to the IC.
When starting up power supplies, VEE and VCC should be powered on simultaneously or VEE first; then followed by VCC.
Over Ta 25C, reduce at the rate of 4.5mW/C. When installed on the standard board (size: 70x70x1.6mm).
Operating conditions
It must function normally at Ta
Parameter
Operating source voltage
25C.
*2
55 to +125
*1
20 to +75
Operating temperature range
Parameter
Absolute maximum ratings (Ta=25
Symbol
VCC
VEE
Min.
5
-7.3
Ratings
Typ.
7
-7
174
Max.
7.3
-5
Unit
V
AVR 2650
harman/kardon
BD3812F
Application circuit
10
1
13
OUT2
12
SEL
IN2
OUT1
AGND
14
IN1
11
10
AGND
DGND
V EE
10
MUTE
DA
CL
47
6
LOGIC
AGND
47
V CC
UNIT
RESISTOR :
CAPACITOR : F
Fig.2
Reference data
OUTPUT VOLTAGE (Vrms)
VCC
1.5
GAIN(dB)
CIRCUIT CURRENT (mA)
10
10
2.5
0.5
0
-0.5
2
0
-2
-4
-1
VEE
-1.5
-6
-2
-8
-2.5
-10
0
POWER SUPPLY (V)
1000
10000
GAIN (dB)
0.01
0.001
0.001
10
0, 618dB
2dB/step
0.0001
-5
0.01
0.1
10
INPUT VOLTAGE (Vrms)
Fig.6 THD+N - Input voltage
10
100
1000
10000
100000
FREQUENCY (Hz)
Fig.7 Output gain - Frequency
175
0.1
10
Fig.5 Output voltage - Input voltage
15
0.1
0.01
INPUT VOLTAGE (Vrms)
20
0.01
0.001
100000
Fig.4 Voltage gain - Frequency
10
THD+N (%)
100
FREQUENCY (Hz)
Fig.3 Circuit current - Power supply
0.1
0.001
10
10
AVR 2650
harman/kardon
T5CN5
32-bit RISC Microcontroller TX03 Series
T5CN5
Overview and Features
The TX03 series is a 32-bit RISC microcontroller series with an ARM CortexTM-M3 microcontroller
core.
Features of the T5CN5 is as follows:
1.1 Features
ARM Cortex-M3 microcontroller core
1) Improved code efficiency has been realized through the use of Thumb2 instruction
New 16-bit Thumb instructions for improved program flow

New 32-bit Thumb instructions for improved performance
Auto-switching between 32-bit instruction and 16-bit instruction is executed by compiler.
2) Both high performance and low power consumption have been achieved.
-High performance
A 32-bit multiplication (3232=32 bit) can be executed with one clock.

Division takes between 2 and 12 cycles depending on dividend and devisor
-Low power consumption
Optimized design using a low power consumption library

Standby function that stops the operation of the microcontroller core
3) High-speed interrupt response suitable for real-time control
(1)
An interruptible long instruction.

Stack push automatically handled by hardware.
176
AVR 2650
harman/kardon
T5CN5
(2)
On Chip program memory and data memory

Product name
On chip RAM
T5CN5
(3)
On chip Flash ROM

512Kbyte
32Kbyte
16-bit timer
16-bit interval timer mode
16-bit event counter mode
16-bit PPG output
: 10 channels
Input capture function
(4)
Real time clock (RTC)

: 1 channel
Clock (hour, minute and second)
Calendar (Month, week, date and leap year)
Time correction
or
30 seconds (by software)
Alarm (Alarm output)
Alarm interrupt
(5)
Watchdog timer
26 cycles of binary counter
Watchdog timer out
(6)
General-purpose serial interface

: 3 channels
Either UART mode or synchronous mode can be selected (4byte FIFO equipped)
(7)
Serial bus interface

: 3 channels
Either I2C bus mode or synchronous mode can be selected.
(8)
CEC
: 1 channel
(9)
: 1 channel
Transmission and reception per
byte.
Remote control signal preprocessor

Can receive up to 72bit data at a time
: 2 channels
(10) 10-bit A/D converter

Start by an internal or external timer trigger
Fixed channel/scan mode
Single/repeat mode
AD monitoring 2ch
Conversion speed 1.15usec(@fsys = 40MHz)
: 12 channels
(11) Interrupt source

Internal: 42 factorsThe order of precedence can be set over 7 levels (except the watchdog
timer interrupt).
External: 8 factorsThe order of precedence can be set over 7 levels.
(12) Input/ output ports

79 pins
177
AVR 2650
harman/kardon
T5CN5
(13) Standby mode

Standby modes
:IDLE, SLOW, SLEEP, STOP
Sub clock operation(32.768kHz)
:SLOW, SLEEP
(14) Clock generator

On-chip PLL (quadrupled)
Clock gear function: The high-speed clock can be divided into 1/1, 1/2, 1/4 or 1/8.
(15) Endian
Little endian
(16) Maximum operating frequency

40MHz
(17) Operating voltage range

2.7V~3.6V (with on-chip regulator)
(18) Temperature range

-20~85 degrees (except during Flash writing/ erasing)
0~70 degrees (during Flash writing/ erasing)
(19) Package
LQFP100-P-1414-0.5H (14mm
14mm, 0.5mm pitch)
178
AVR 2650
harman/kardon
T5CN5
1.2 Block Diagram
I/F
FLASH
I/F
RAM
I/F
BOOT
ROM
I-Code
D-Code
Debug
System
AHB-Bus-Matrix
Cortex-M3
CPU
NVIC
Bus Bridge
CG
PORT 0~A
SIO (3ch)
TMRB (10ch)
IO-Bus
I2C (3ch)
WDT
CEC
RTC
Remote control signal

preprocessor (2ch)
ADC (12ch)
Fig. 1.1 T5CN5 Block Diagram
179
AVR 2650
harman/kardon
T5CN5
2.
Pin Layout and Pin Functions

This chapter describes the pin layout, pin names and pin functions of T5CN5.
2.1
Pin Layout (Top view)
80
85
90
95
75
5
70
10
T5CN5
65
Top View
15
60
20
50
45
40
35
25
30
55
SDA0/ SO0/ PG0

SCL0/ SI0/ PG1
SCK0/ PG2
PB3
BOOT/ TB0IN0/ PH0
TB0IN1/ PH1
TB1IN0/ PH2
TXD2/ PF0
RXD2/ PF1
CTS2/ SCLK2/ PF2
TB1IN1/ PH3
PB4
TB0OUT/ PI0
INT6/ PJ6
TB1OUT/ PI1
PB5
TB2OUT/ PI2
PB6
SDA1/ SO1/ PF4
SCL1/ SI1/ PF5
SCK1/ PF6
PB7
TB3OUT/ PI3
INT1/ PJ1
CEC/ PK0
AN10/ PD6
AN11/ PD7
AVSS
VREFH
AVCC
INT4/ PG3
TB9OUT/ PK2
TB7OUT/ PJ5
TB2IN0/ PH4
TB2IN1/ PH5
TB8OUT/ PG7
TEST2
DVSS
DVCC
SDA2/ SO2/ PG4
SCL2/ SI2/ PG5
SCK2/ PG6
TEST1
INT5/ PF7
TXD0/ PE0
RXD0/ PE1
CTS0/ SCLK0/ PE2
TXD1/ PE4
RXD1/ PE5
CTS1/ SCLK1/ PE6
100
PD5 /AN9
PD4 /AN8
PD3 /AN7 /TB6IN1
PD2 /AN6 /TB6IN0
PD1 /AN5 /TB5IN1
PD0 /AN4 /TB5IN0
PC3 /AN3
PC2 /AN2
PC1 /AN1
PC0 /AN0
TEST4
PE3 /RXIN0
PJ4 /TB6OUT
PJ3 /INT3
PJ2 /INT2
PH7 /TB3IN1
PH6 /TB3IN0
PI7 /TB4IN1
RESET
MODE
NMI
PI6 /TB4IN0
XT2
XT1
REGVCC
Fig. 2-1 shows the pin layout of T5CN5.
Fig. 2.1 Pin Layout (LQFP100)
180
REGVSS
X1
CVSS
X2
CVCC
PJ0 /INT0
PA7
PA6 /TRACEDATA3
PA5 /TRACEDATA2
PA4 /TRACEDATA1
PA3 /TRACEDATA0
PA2 /TRACECLK
DVSS
DVCC
PF3 /RXIN1
PB2 / TRST
PB1 /TDI
PJ7 /INT7
TEST3
PA1 /TCK /SWCLK
PA0 /TMS /SWDIO
PB0 /TDO /SWV
PI5 /TB5OUT
PI4 /TB4OUT
PK1 /SCOUT /ALARM
AVR 2650
harman/kardon
T5CN5
Table 2.1 Pin Numbers and Names (1/2)

Pin
No.
1
2
3
4
Pin name
PD6, AN10
PD7, AN11
AVSS
VREFH
Pin
No.
26
27
28
29
AVCC
30
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PG3, INT4
PK2, TB9OUT
PJ5, TB7OUT
PH4, TB2IN0
PH5, TB2IN1
PG7, TB8OUT
TEST2
DVSS
DVCC
PG4, SO2, SDA2
PG5, SI2, SCL2
PG6, SCK2
TEST1
PF7, INT5
PE0, TXD0
PE1, RXD0
PE2, SCLK0, CTS0
PE4, TXD1
PE5, RXD1
PE6, SCLK1, CTS1
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
181
Pin name
PG0, SO0, SDA0
PG1, SI0, SCL0
PG2, SCK0
PB3
PH0, TB0IN0, BOOT
PH1, TB0IN1
PH2, TB1IN0
PF0, TXD2
PF1, RXD2
PF2, SCLK2, CTS2
PH3, TB1IN1
PB4
PI0, TB0OUT
PJ6, INT6
PI1, TB1OUT
PB5
PI2, TB2OUT
PB6
PF4, SO1, SDA1
PF5, SI1, SCL1
PF6, SCK1
PB7
PI3, TB3OUT
PJ1, INT1
PK0, CEC
AVR 2650
harman/kardon
T5CN5
Table 2.1 Pin Numbers and Names (2/2)

Pin
No.
Pin name
Pin
No.
Pin name
76
REGVCC
52
53
54
55
56
PK1, SCOUT, ALARM

PI4, TB4OUT
PI5, TB5OUT
PB0, TDO, SWV
PA0, TMS, SWDIO
PA1, TCK, SWCLK
77
78
79
80
81
XT1
XT2
PI6, TB4IN0
57
TEST3
82
58
59
PJ7, INT7
PB1, TDI
83
84
RESET
PI7, TB4IN1
PH6, TB3IN0
60
PB2, TRST
PF3, RXIN1
DVCC
DVSS
PA2, TRACECLK
PA3, TRACEDATA0
PA4, TRACEDATA1
PA5, TRACEDATA2
PA6, TRACEDATA3
PA7
PJ0, INT0
CVCC
X2
CVSS
X1
REGVSS
85
PH7, TB3IN1
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
PJ2, INT2
PJ3, INT3
PJ4, TB6OUT
PE3, RXIN0
TEST4
PC0, AN0
PC1, AN1
PC2, AN2
PC3, AN3
PD0, AN4, TB5IN0
PD1, AN5, TB5IN1
PD2, AN6, TB6IN0
PD3, AN7, TB6IN1
PD4, AN8
PD5, AN9
51
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
182
NMI
MODE
AVR 2650
harman/kardon
T5CN5
2.2
Pin names and Functions
Table 2.2 and Table 2.3 sort the input and output pins of the T5CN5 by pin or port. Each table includes
alternate pin names and functions for multi-function pins.
3.1.1
Sorted by Pin
Table 2.2 Pin Names and Functions Sorted by Pin (1/5)
I/O
I
I/O
O
I/O
I
I/O
I
I/O
I
I/O
O
I/O
SDA2/
SO2
PG5
I/O
O
I/O
SCL2/
SI2
PG6
SCK2
I/O
I
I/O
I/O
7
8
Function
9
10
11
Test
PS
12
13
14
15
Function
16
17
Test
18
TEST1
Function
19
PF7
INT5
I/O
I
I/O port
183
Pull up
w/ noise filter
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
PG3
INT4
PK2
TB9OUT
PJ5
TB7OUT
PH4
TB2IN0
PH5
TB2IN1
PG7
TB8OUT
TEST2
DVSS
DVCC
PG4
w/ noise filter
AVCC
VREFH
Pull up
PS
AVSS
Pull up
Function
Input port
Analog input
Input port
Analog input
A/D converter: GND pin (0V)
Tie AVSS to power supply even if the A/D
converter is not used.
Supplying the A/D converter with a
reference power supply.
Tie VREFH to power supply even if the
A/D converter is not used.
Supplying the A/D converter with a power
supply. Tie AVCC to power supply even if
the A/D converter is not used.
I/O port
I/O port
Timer B output
I/O port
Timer B output
I/O port
I/O port
I/O port
Timer B output
GND pin
Power supply pin
I/O port
I/O port
I/O port
mode.
Programm
able Open
Drain
Output
I
I
I
I
Schmitt
trigger
PD6
AN10
PD7
AN11
Function
Programma
ble Pull up/
Pull down
Pin Name
Input/
Output
Type
# of
Pins
AVR 2650
harman/kardon
T5CN5
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
184
w/ noise filter
39
Pull up
38
37
Pull up
36
35
Pull up
Function
Pull up
34
33
32
Pull up
I/O
I
I/O
I
I/O
O
I/O
I
I/O
I
I
I/O
I
I/O
I/O
O
I/O
I
PH1
TB0IN1
PH2
TB1IN0
PF0
TXD2
PF1
RXD2
PF2
SCLK2
CTS2
PH3
TB1IN1
PB4
PI0
TB0OUT
PJ6
INT6
31
Pull up
BOOT
I/O
I
I
Pull up
PH0
TB0IN0
Pull up
Function/
Control
Pull up
30
28
Pull up
I/O
27
PB3
26
Pull up
29
25
Function
Pull up
I/O
I
I/O
I/O
24
Pull up
SCL0/
SI0
PG2
SCK0
23
I/O
O
I/O
22
Pull up
SDA0/
SO0
PG1
21
I/O port
Sending serial data
I/O port
I/O port
Handshake input pin
I/O port
Sending serial data
I/O port
I/O port
Handshake input pin
I/O port
I/O port
I/O port
mode.
I/O port
I/O port
Setting a single boot mode: This pin
goes into single boot mode by sampling
"L" at the rise of a reset signal.
I/O port
I/O port
I/O port
Sending serial data
I/O port
I/O port
Handshake input pin
I/O port
I/O port
I/O port
Timer B output
I/O port
I/O
O
I/O
I
I/O
I
I
I/O
O
I/O
I
I/O
I
I
I/O
Schmitt
trigger
PE0
TXD0
PE1
RXD0
PE2
SCLK0
CTS0
PE4
TXD1
PE5
RXD1
PE6
SCLK1
CTS1
PG0
20
Function
Programma
ble Open
Drain
Output
Programm
able
Pull-up/
Pull down
Input/
Pin Name
Output
Type
# of
Pins
AVR 2650
harman/kardon
T5CN5
w/ noise filter
(Note 4)
w/ noise filter
Pull up
Pull up
185
PS
Pull up
Function
Function/
Debug

I/O port
I/O port
Debug pin
I/O port
Debug pin
I/O port
Inputting signal to remote controller
Power supply pin
GND pin
Function
47 PB7
I/O
PI3
I/O
48
TB3OUT
O
PJ1
I/O
49
INT1
I
PK0
I/O
50
CEC
I/O
PK1
I/O
51 SCOUT
O
O
ALARM
PI4
I/O
52
TB4OUT
O
PI5
I/O
53
TB5OUT
O
PB0
I/O
54
TDO/SWV O
PA0
I/O
55
TMS/SWDIO I/O
PA1
I/O
56 TCK/
I
SWCLK
57 TEST3
PJ7
I/O
58
INT7
I
PB1
I/O
59
TDI
I
PB2
I/O
60
I
TRST
PF3
I/O
61
RXIN1
I
62 DVCC
63 DVSS
-
Test
I/O
I
I/O
I/O
Function/
Debug
46
SCL1/
SI1
PF6
SCK1
Programmab
le Open
Drain
Output
Function
I/O
O
I/O
Pull up
I/O port
Timer B output
Pull up
I/O port
I/O port
Pull up
Timer B output
Pull up
I/O port
I/O port
Pull up
I/O port
Pull up
I/O port
Pull up
mode.
Pull up
I/O port
I/O port
Pull up
Timer B output
I/O port
Pull up
I/O port
CEC pin
I/O port
System clock output
Pull up
Alarm output
I/O port
Pull up
Timer B output
I/O port
Pull up
Timer B output
I/O port
Pull up
Debug pin
I/O port
Pull up
Debug pin
I/O port
Pull up
Debug pin
Schmitt
trigger
45
SDA1/
SO1
PF5
Programmab
le Pull-up/
Pull down
44
I/O
O
I/O
I/O
O
I/O
I/O
Function
PI1
TB1OUT
41 PB5
PI2
42
TB2OUT
43 PB6
PF4
40
Input/
Output
Pin Name
# of
Pins
Type
Pull up
AVR 2650
harman/kardon
T5CN5
I/O port
PJ0
INT0
CVCC
X2
CVSS
X1
REGVSS
REGVCC
XT1
XT2
PI6
TB4IN0
I/O
I
O
I
I
O
I/O
I
I/O port
Power supply pin
GND pin
GND pin
Power supply pin
I/O port
NMI
Non-maskable interrupt
81 MODE
Mode pin: Tied to GND pin
Reset input pin
I/O
I
I/O
I
I/O
I
I/O
I
I/O port
I/O port
I/O port
I/O port
PJ3
INT3
I/O
I
I/O port
PJ4
TB6OUT
PE3
89
RXIN0
I/O
O
I/O
I
I/O port
Timer B output
I/O port
Inputting signal to remote controller
90 TEST4
80
Control
RESET
PI7
TB4IN0
PH6
84
TB3IN0
PH7
85
TB3IN1
PJ2
86
INT2
83
Function
87
88
Test
186
Pull up
-
w/ noise filter
w/ noise filter
Tied to
Pull up
w/ noise filter
Pull up
Pull up
Pull up
Pull up
w/ noise filter
w/ noise filter
Pull up
Pull up
79
Function
Clock
Pull up
PS
Pull up
PS
Clock
Clock
71
72
73
74
75
76
77
78
PS
70
69 PA7
Function
PA6
TRACEDATA3
68
PA5
TRACEDATA2
67
PA4
TRACEDATA1
66
Pull up
82
Function/
Debug
PA3
TRACEDATA0
Pull up
I/O
65
Programmab
le Open
Drain
Output
Pull up
I/O port
Debug pin
I/O port
Debug pin
I/O port
Debug pin
I/O port
Debug pin
I/O port
Debug pin
TRACECLK
Schmitt
trigger
Pull up
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
64
Programma
ble Pull-up/
Pull down
Pull up
Function
PA2
Input/
Output
Pin Name
# of
Pins
Type
Pull up
AVR 2650
harman/kardon
T5CN5
Type
# of
Pins
PC0
AN0
PC1
92
AN1
PC2
93
AN2
PC3
94
AN3
PD0
95 AN4
TB5IN0
PD1
96 AN5
TB5IN1
PD2
97 AN6
TB6IN0
PD3
98 AN7
TB6IN1
PD4
99
AN8
PD5
100
AN9
91
Function
(Note 1)
(Note 2)
(Note 3)
(Note 4)
Pin Name
Input/
Output
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Function
Input port
Analog input
Input port
Analog input
Input port
Analog input
Input port
Analog input
Input port
Analog input
Input port
Analog input
Input port
Analog input
Input port
Analog input
Inputting the timer B capture trigger of
Input port
Analog input
Input port
Analog input
Programma
ble Pull-up/
Pull down
Schmitt
trigger
Programma
ble Open
Drain
Output
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
Pull up
TEST1 through 4 must be left unconnected.

Be sure to tie MODE to GND.
Tie VREFH/ AVCC to power supply and AVSS to GND even if the A/D converter is not used.
Nch open drain port.
187
AVR 2650
harman/kardon
T5CN5
2.3
Pin Names and Power Supply Pins

Table 2.4 Pin Names and Power Supplies
Power
Pin name
supply
PA
PB
PC
PD
PE
PF
PG
PH
PI
PJ
PK
X1, X2
XT1, XT2
DVCC
DVCC
AVCC
AVCC
DVCC
DVCC
DVCC
DVCC
DVCC
DVCC
DVCC
CVCC
DVCC
DVCC
DVCC
DVCC
RESET
NMI
MODE
2.4
Pin Numbers and Power Supply Pins

Table 2.5 Pin Numbers and Power Supplies
Power
supply
DVCC
AVCC
REGVCC
CVCC
Pin number
14, 62
5
76
71
188
Voltage range
2.7V~3.6V
AVR 2650
harman/kardon
ESMT
M12L16161A
SDRAM
512K x 16Bit x 2Banks

Synchronous DRAM
FEATURES
GENERAL DESCRIPTION
JEDEC standard 3.3V power supply

LVTTL compatible with multiplexed address
Dual banks operation
MRS cycle with address key programs
CAS Latency (2 & 3 )
Burst Length (1, 2, 4, 8 & full page)
Burst Type (Sequential & Interleave)
All inputs are sampled at the positive going edge of the
system clock
Burst Read Single-bit Write operation
DQM for masking
Auto & self refresh
32ms refresh period (2K cycle)
The M12L16161A is 16,777,216 bits synchronous high

data rate Dynamic RAM organized as 2 x 524,288 words by
16 bits, fabricated with high performance CMOS technology.
Synchronous design allows precise cycle control with the
use of system clock I/O transactions are possible on every
clock cycle. Range of operating frequencies, programmable
burst length and programmable latencies allow the same
device to be useful for a variety of high bandwidth, high
performance memory system applications.
ORDERING INFORMATION
Part NO.
MAX Freq.
M12L16161A-5TG
200MHz
TSOP(II)
Pb-free
M12L16161A-7TG
143MHz
TSOP(II)
Pb-free
143MHz
VFBGA
Pb-free
M12L16161A-7BG
PACKAGE COMMENTS
PIN CONFIGURATION (TOP VIEW)

1
VDD
50
DQ0
49
48
47
46
DQ3
45
44
43
42
10
41
DQ6
11
40
12
39
13
38
14
37
15
36
16
35
17
34
CS
18
33
19
32
20
31
21
30
22
29
A2
23
28
24
27
A4
VDD
25
26
VSS
DQ5
DQ9
VDDQ
VSSQ
DQ6
DQ8
NC
NC
DQ7
NC
NC
NC
NC
NC
UDQM
LDQM
WE
NC
CLK
RAS
CAS
CKE
NC
NC
CS
A11
A9
NC
NC
A8
A7
A0
A10
A5
A3
VDDQ
A6
VSSQ
A6
A5
A2
A1
VSS
A4
A3
VDD
A7
A1
DQ10
A8
A0
DQ3
A9
A10/AP
DQ4
N.C
BA
DQ11
CKE
DQ12
CLK
RAS
DQ2
UDQM
CAS
VSSQ
N.C/RFU
WE
VDDQ
VDDQ
LDQM
DQ13
DQ8
VDDQ
DQ1
DQ9
DQ7
VDDQ
VSSQ
DQ10
VSSQ
VSSQ
DQ11
DQ5
VDDQ
DQ4
DQ14
DQ12
VDDQ
VSS
VDD
DQ13
VSSQ
DQ2
DQ0
DQ14
VSSQ
DQ15
DQ15
DQ1
VSS
50PIN TSOP(II)
(400mil x 825mil)
(0.8 mm PIN PITCH)
Elite Semiconductor Memory Technology Inc.
60 Ball VFBGA
(6.4x10.1mm)
(0.65mm ball pitch)
Publication Date : May. 2005

Revision : 2.4
2/30
189
AVR 2650
harman/kardon
ESMT
M12L16161A
Col. Buffer
LCKE
512K x 16
LWE
LDQM
Output Buffer
Row Decoder
LRAS
LCBR
ADD
512K x 16
Sense AMP
Row Buffer
Refresh Counter
Address Register
CLK
Data Input Register
I/O Control
Bank Select
DQi
Column Decoder
Latency & Burst Length
Programming Register
LRAS
LCBR
LWE
LCAS
LWCBR
LDQM
Timing Register
CLK
CKE
CS
RAS
CAS
WE
L(U)DQM
PIN FUNCTION DESCRIPTION

CLK
Pin
Name
System Clock
Input Function
Active on the positive going edge to sample all inputs.
Disables or enables device operation by masking or enabling all inputs except
CLK, CKE and L(U)DQM.
Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one cycle prior to new command.
Disable input buffers for power down in standby.
Row / column addresses are multiplexed on the same pins.
Row address : RA0 ~ RA10, column address : CA0 ~ CA7
Selects bank to be activated during row address latch time.
Selects bank for read/write during column address latch time.
CS
Chip Select
CKE
Clock Enable
A0 ~ A10/AP
Address
BA
Bank Select Address
RAS
Row Address Strobe
Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.
Latches column addresses on the positive going edge of the CLK with
CAS
Column Address Strobe
WE
Write Enable
CAS low.
Enables column access.
Enables write operation and row precharge.
L(U)DQM
Data Input / Output Mask
Latches data in starting from CAS , WE active.

Makes data output Hi-Z, tSHZ after the clock and masks the output.
Blocks data input when L(U)DQM active.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2005

Revision : 2.4
3/30
190
AVR 2650
harman/kardon
M24128
M24C64 M24C32
128 Kbit, 64 Kbit and 32 Kbit serial IC bus EEPROM
Features
Two-wire I2C serial interface

supports 400 kHz protocol
Single supply voltages (see Table 1 for root

part numbers):
2.5 V to 5.5 V
1.8 V to 5.5 V
1.7 V to 5.5 V
Write Control input
Byte and Page Write
Random and Sequential Read modes
Self-timed programming cycle
Automatic address incrementing
Enhanced ESD/latch-up protection
More than 1 Million write cycles
More than 40-year data retention
PDIP8 (BN)
Packages
ECOPACK (RoHS compliant)
Table 1.
TSSOP8 (DW)
169 mil width
Device summary
Reference
Part number
Supply voltage
M24128-BW
1.8 V to 5.5V
1.7 V to 5.5V
2.5 V to 5.5V
M24C64-R
1.8 V to 5.5V
M24C64-F
1.7 V to 5.5V
M24C32-W
2.5 V to 5.5V
M24C32-R
1.8 V to 5.5V
M24C32-F
M24C32
M24128-BR
M24C64-W
M24C64
2.5 V to 5.5V
M24128-BF
M24128
SO8 (MN)
150 mil width
1.7 V to 5.5V
September 2008
UFDFPN8 (MB)
2 3 mm (MLP)
WLCSP (CS)
Rev 15
1/39
www.st.com
191
AVR 2650
harman/kardon
M24128, M24C64, M24C32

Table 2.
Description
Signal names
Signal name
Function
Direction
E0, E1, E2
Chip Enable
Input
SDA
Serial Data
I/O
SCL
Serial Clock
Input
WC
Write Control
Input
VCC
Supply voltage
VSS
Ground
Figure 2.
DIP, SO, TSSOP and UFDFPN connections

M24128
M24C64
M24C32
8
1
7
2
6
3
5
4
E0
E1
E2
VSS
VCC
WC
SCL
SDA
AI01845e
1. See Package mechanical data section for package dimensions, and how to identify pin-1.
Figure 3.
M24128 WLCSP connections (top view, marking side, with balls on the
underside)
VCC
E1
E2
WC
SDA
E0
SCL
VSS
ai14799
7/39
192
AVR 2650
harman/kardon
ML61
ML61 Series Positive Voltage Detector

Application
Features
Memory Battery Back-up Circuits

Microprocessor Reset Circuitry
Power Failure Detection
Power-on Reset Circuit
System Battery Life and Charge Voltage
Monitor
CMOS Low Power Consumption : Typical 1.0uAat

Vin=2.0V
Selectable Detect V
oltage : 1.1V to 6.0V in 0.1V increments
HighlyAccurate : Detect V
oltage 1.1V to 1.9V + 3%
Detect V
oltage 2.0V to 6.0V + 2%
Operating V
oltage : 0.8V to 10.0V
PackageAvailable : SOT23 (150mW), SOT89 (500mW)
& TO92 (300mW)
General Description
The ML61 is a group of high-precision and low-power voltage detectors.
The ML61 consists of a highly-accurate and low-power reference voltage source, a comparator,
a hysteresis circuit, and an output driver. Detect voltage is very accurate and stable with
N-channel open drain and CMOS, are available.
Block Diagram
(1) CMOS Output
SOT-89
(2) N-Channel Open Drain Output
Pin Configuration
Pin Number Pin Name
Description
VOUT
Supply Voltage Output
VIN
Supply Voltage Input
VSS
Ground
193
AVR 2650
harman/kardon
194
AVR 2650
harman/kardon
195
AVR 2650
harman/kardon
196
AVR 2650
harman/kardon
NJU7223
500mA Low Dropout Voltage Regulator
I GENERAL DESCRIPTION
The NJU7223 series is a high precision output voltage,
low drop output, low current consumption and high output
current 3-terminal positive voltage regulator with a over
current protection and a thermal shutdown.
Low dropout voltage is realized at high current output.
I PACKAGE OUTLINE
I FEATURES
123
GHigh Precision Output Voltage 2%
GHigh Output Current
Io(max.)=500mA
NJM7223F
GLow Current Consumption
30A
GLow Dropout Voltage
VIO=0.4V typ. (Io=0.5A,Vo=5V) 1.VOUT
GInternal Over Current Protection
2.VIN
GInternal Thermal Shutdown Protection
3.GND
GPackage Outline
TO-220F, TO-252
GC-MOS Technology
I OUTPUT VOLTAGE LINE-UP
TO-220F
VOUT
+1.8V
NJU7223F18
+2.5V
NJU7223F25
+3.0V
NJU7223F30
+3.3V
NJU7223F33
+5.0V
NJU7223F50
TO-252
NJU7223DL1-18
NJU7223DL1-25
NJU7223DL1-30
NJU7223DL1-33
NJU7223DL1-50
I EQUIVALENT CIRCUIT
Over Current Protection
VOUT
VIN
Thermal shutdown
Protection
VREF
GND
GND
197
3
1
NJU7223DL1
AVR 2650
harman/kardon
198
AVR 2650
harman/kardon
199
AVR 2650
harman/kardon
SN54ACT04, SN74ACT04
HEX INVERTERS
SCAS518C JULY 1995 REVISED OCTOBER 2003
D 4.5-V to 5.5-V VCC Operation

D Inputs Accept Voltages to 5.5 V
D Max tpd of 8.5 ns at 5 V

D Inputs Are TTL-Voltage Compatible
SN54ACT04 . . . J OR W PACKAGE
SN74ACT04 . . . D, DB, N, NS, OR PW PACKAGE
(TOP VIEW)
1
14
13
12
11
5
6
7
10
9
8
1Y
1A
NC
VCC
6A
VCC
6A
6Y
5A
5Y
4A
4Y
2A
NC
2Y
NC
3A
3 2 1 20 19
18
17
16
15
14
9 10 11 12 13
6Y
NC
5A
NC
5Y
3Y
GND
NC
4Y
4A
1A
1Y
2A
2Y
3A
3Y
GND
SN54ACT04 . . . FK PACKAGE
(TOP VIEW)
NC No internal connection
description/ordering information
The ACT04 devices contain six independent inverters. The devices perform the Boolean function Y = A.
ORDERABLE
PART NUMBER
PACKAGE
TA
PDIP N
TOP-SIDE
MARKING
Tube
SN74ACT04N
Tube
SN74ACT04D
Tape and reel
SN74ACT04DR
SOP NS
Tape and reel
SN74ACT04NSR
ACT04
SSOP DB
Tape and reel
SN74ACT04DBR
AD04
Tube
SN74ACT04PW
Tape and reel
SN74ACT04PWR
CDIP J
Tube
SNJ54ACT04J
SNJ54ACT04J
CFP W
Tube
SNJ54ACT04W
SNJ54ACT04W
LCCC FK
Tube
SNJ54ACT04FK
SOIC D
40 C 85 C
40C to 85C
TSSOP PW
55 C 125 C
55C to 125C
SN74ACT0N
ACT04
AD04
SNJ54ACT04FK
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
FUNCTION TABLE
(each inverter)
INPUT
A
OUTPUT
Y
200
AVR 2650
harman/kardon
8 Mbit SPI Serial Flash

SST25VF080B
Data Sheet
PIN DESCRIPTION
CE#
SO
VDD
HOLD#
CE#
SO
VDD
HOLD#
Top View
Top View
WP#
SCK
WP#
SCK
VSS
SI
VSS
SI
1296 08-soic S2A P1.0
1296 08-wson QA P2.0
8-LEAD SOIC
8-CONTACT WSON
FIGURE 1: PIN ASSIGNMENTS

TABLE 1: PIN DESCRIPTION
Symbol
Pin Name
Functions
SCK
Serial Clock
To provide the timing of the serial interface.

Commands, addresses, or input data are latched on the rising edge of the clock input,
while output data is shifted out on the falling edge of the clock input.
SI
Serial Data Input
To transfer commands, addresses, or data serially into the device.

Inputs are latched on the rising edge of the serial clock.
SO
Serial Data Output
To transfer data serially out of the device.

Data is shifted out on the falling edge of the serial clock.
Outputs Flash busy status during AAI Programming when reconfigured as RY/BY# pin.
See Hardware End-of-Write Detection on page 12 for details.
CE#
Chip Enable
The device is enabled by a high to low transition on CE#. CE# must remain low for the
duration of any command sequence.
WP#
Write Protect
The Write Protect (WP#) pin is used to enable/disable BPL bit in the status register.
HOLD#
Hold
To temporarily stop serial communication with SPI flash memory without resetting the
device.
VDD
Power Supply
To provide power supply voltage: 2.7-3.6V for SST25VF080B
VSS
Ground
T1.0 1296
201
AVR 2650
harman/kardon
8 Mbit SPI Serial Flash

SST25VF080B
Data Sheet
SuperFlash
Memory
X - Decoder
Address
Buffers
and
Latches
Y - Decoder
I/O Buffers
and
Data Latches
Control Logic
Serial Interface
1296 B1.0
CE#
SCK
SI
SO
202
WP#
HOLD#
AVR 2650
harman/kardon
TC74VCX541FT/FK/FTG
Silicon Monolithic
TC74VCX541FT, TC74VCX541FK, TC74VCX541FTG

Low-Voltage Octal Bus Buffer with 3.6 V Tolerant Inputs and Outputs
The TC74VCX541 is a high performance CMOS octal bus
buffer which is guaranteed to operate from 1.2-V to 3.6-V.
Designed for use in 1.5V, 1.8 V, 2.5 V or 3.3 V systems, it
achieves high speed operation while maintaing the CMOS low
power dissipation.
It is also designed with over voltage tolerant inputs and
outputs up to 3.6 V.
The device is a non-inverting 3-state buffer having two
active-low output enables. When either OE1 or OE2 are high, the
terminal outputs are in the high-impedance state. This device is
designed to be used with 3-state memory address drivers, etc.
All inputs are equipped with protection circuits against static
discharge.
TC74VCX541FT
TC74VCX541FK
Features (Note 1)
Low voltage operation: VCC = 1.2~3.6 V
High speed operation: tpd = 3.5 ns (max) (VCC = 3.0~3.6 V)

tpd = 4.2 ns (max) (VCC = 2.3~2.7 V)
tpd = 8.4 ns (max) (VCC = 1.65~1.95 V)
tpd = 16.8 ns (max) (VCC = 1.4~1.6 V)
TC74VCX541FTG
tpd = 42.0 ns (max) (VCC = 1.2 V)
3.6 V tolerant inputs and outputs.
Output current: IOH/IOL = 24 mA (min) (VCC = 3.0 V)

IOH/IOL = 18 mA (min) (VCC = 2.3 V)
Latch-up performance: 300 mA
ESD performance: Machine model

200 V
Human body model
2000 V
VQON20-0404-0.50
Weight
TSSOP20-P-0044-0.65A
VSSOP20-P-0030-0.50
VQON20-P-0404-0.50
Package: TSSOP
VSSOP (US)
VQON
Power down protection is provided on all inputs and outputs.
Note 1: When mounting VQON package, the type of recommended flux is RA or RMA.
203
: 0.08 g (typ.)
: 0.03 g (typ.)
: 0.0145g (typ.)
AVR 2650
harman/kardon
TC74VCX541FT/FK/FTG
Pin Assignment (top view)
FT(TSSOP20-P-0044-0.65)
FK(VSSOP20-P-0030-0.50)
FTG(VQON20-P-0404-0.50)
A1 OE1 VCC OE2 Y1
OE1
20
VCC
A1
19
OE2
A2
18
Y1
A2
15
Y2
A3
17
Y2
A3
14
Y3
A4
16
Y3
A4
13
Y4
A5
15
Y4
A5
12
Y5
A6
14
Y5
A6
11
Y6
A7
13
Y6
A8
12
Y7
GND 10
11
Y8
20
6
A7
IEC Logic Level

OE1
OE2
A1
A2
A3
A4
A5
A6
A7
A8
(1)
(19)
&
EN
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(18)
Y1
Y2
(17)
(16)
Y3
Y4
(15)
(14)
Y5
Y6
Y7
Y8
(13)
(12)
(11)
Truth Table
Inputs
Outputs
OE1
OE2
An
X: Dont care
Z: High impedance
204
19
18
17
A8 GND Y8
16
10
Y7
AVR 2650
harman/kardon
205
AVR 2650
harman/kardon
TL071, TL071A, TL071B, TL072

TL072A, TL072B, TL074, TL074A, TL074B
LOWNOISE JFETINPUT OPERATIONAL AMPLIFIERS
SLOS080J SEPTEMBER 1978 REVISED MARCH 2005
TL071, TL071A, TL071B

D, P, OR PS PACKAGE
(TOP VIEW)
OFFSET N1
IN
IN+
VCC
TL072, TL072A, TL072B

D, JG, P, PS, OR PW PACKAGE
(TOP VIEW)
NC
VCC+
OUT
OFFSET N2
1OUT
1IN
1IN+
VCC
TL074A, TL074B
D, J, N, NS, OR PW PACKAGE
TL074 . . . D, J, N, NS, PW,
OR W PACKAGE
(TOP VIEW)
VCC+
2OUT
2IN
2IN+
1OUT
1IN
1IN+
VCC+
2IN+
2IN
2OUT
TL072
U PACKAGE
(TOP VIEW)
NC
1OUT
1IN
1IN+
VCC
1
2
17
16
15
14
9 10 11 12 13
NC
VCC+
NC
OUT
NC
NC
1IN
NC
1IN+
NC
13
12
11
10
TL074
FK PACKAGE
(TOP VIEW)
3 2 1 20 19
18
17
16
15
14
9 10 11 12 13
1IN
1OUT
NC
4OUT
4IN
NC
2OUT
NC
2IN
NC
1IN+
NC
VCC+
NC
2IN+
3 2 1 20 19
18
17
16
15
14
9 10 11 12 13
NC No internal connection
symbols
TL071
TL072 (each amplifier)
TL074 (each amplifier)
OFFSET N1
IN+
IN+
IN
OUT
IN
OUT
OFFSET N2
206
4OUT
4IN
4IN+
VCC
3IN+
3IN
3OUT
2IN
2OUT
NC
3OUT
3IN
NC
V CC
NC
2IN+
NC
3 2 1 20 19
18
NC
1OUT
NC
V CC+
NC
NC
OFFSET N1
NC
NC
NC
4
14
NC
VCC+
2OUT
2IN
2IN+
TL072
FK PACKAGE
(TOP VIEW)
NC
V CC
NC
OFFSET N2
NC
NC
IN
NC
IN+
NC
TL071
FK PACKAGE
(TOP VIEW)
10
4IN+
NC
VCC
NC
3IN+
AVR 2650
harman/kardon
ADV7511 ADI Confidential
HARDWARE USERS GUIDE

Rev. PrB
SECTION 5: PIN AND PACKAGE INFORMATION

This section shows the pinout of the ADV7511 100-lead LQFP package. This section also contains a brief description of the
different pins as well as the mechanical drawings
100-lead LQFP configuration (top view - not to scale)

100 GND
99 GND
98 HSYNC
97 DE
96 D0
95 D1
94 D2
93 D3
92 D4
91 D5
90 D6
89 D7
88 D8
87 D9
86 D10
85 D11
84 D12
83 D13
82 D14
81 D15
80 D16
79 CLK
78 D17
77 DVDD
76 DVDD
Figure 6
PIN 1
INDICATOR
ADV 7511
TOP VIEW
( Not to Scale)
BGV DD 26
GND 27
R_EXT 28
AVDD 29
HPD 30
GND 31
TXC 32
TXC+ 33
AVDD 34
TX0 35
TX0+ 36
GND 37
PD 38
TX1 39
TX1+ 40
AV DD 41
TX2 42
TX2+ 43
GND 44
INT 45
SPDIF_OUT 46
DVDD_3V 47
CEC_IN 48
DVDD 49
CEC_CLK 50
DVDD 1
VSYNC 2
DSD0 3
DSD1 4
DSD2 5
DSD3 6
DSD4 7
DSD5 8
DSD_ CLK 9
SPDIF 10
MCLK 11
I2S0 12
I2S1 13
I2S2 14
I2S3 15
SCLK 16
LRCLK 17
GND 18
DVDD 19
GND 20
PVDD 21
GND 22
GND 23
PVDD 24
PVDD 25
Rev. PrB | Page 17 of 55
207
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
GND
D18
D19
D20
D21
D22
D23
D24
D25
D26
D27
D28
D29
D30
D31
D32
D33
D34
D35
SDA
SCL
DDCSDA
DDCSCL
HEAC+
HEAC-
AVR 2650
harman/kardon

Rev. PrB
Table 3
Complete Pinout List ADV7511
Pin No.
57-74, 78, 8096
Mnemonic
D[35:0]
Type1
I
Description
Video Data Input. Digital input in RGB or YCbCr format. Supports typical CMOS logic
levels from1.8V up to 3.3V. See Figure 2 for timing details.
79
97
CLK
DE
I
I
98
2
28
HSYNC
VSYNC
R_EXT
I
I
I
51
52
30
HEACHEAC+
HPD
I
I
I
10
S/PDIF
Video Clock Input. Supports typical CMOS logic levels from 1.8V up to 3.3V.
Data Enable signal input for Digital Video. Supports typical CMOS logic levels from
1.8V up to 3.3V.
Horizontal Sync Input. Supports typical CMOS logic levels from 1.8V up to 3.3V.
Vertical Sync Input. Supports typical CMOS logic levels from 1.8V up to 3.3V.
Sets internal reference currents. Place 887 resistor (1% tolerance) between this
pin and ground.
HEAC- is one of a pair of differential lines for the ARC (Audio Return Channel)
HEAC+ is one of a pair of differential lines for the ARC (Audio Return Channel)
Hot Plug Detect signal input. This indicates to the interface whether the sink is
connected. 1.8V to 5.0 V CMOS logic level.
S/PDIF (Sony/Philips Digital Interface) Audio Input. This pin is typically used as
the audio input from a Sony/Philips digital interface. Supports typical CMOS logic
levels from 1.8V up to 3.3V. See Figure 4 for timing details.
46
11
S/PDIF_OUT
MCLK
O
I
15-12
I2S[3:0]
16
17
SCLK
LRCLK
I
I
8-3
DSD[5:0]
9
38
DSD_CLK
PD/AD
I
I
32, 33
TxC/TxC+
42, 43
Tx2/Tx2+
39, 40
Tx1/Tx1+
35, 36
Tx0/Tx0+
45
INT
29, 34, 41
1, 19, 49, 76,
77
24, 25
AVDD
DVDD
P
P
PVDD
21
PLVDD
26
BGVDD
S/PDIF Audio Output from ARC receiver.

Audio Reference Clock input. 128 N fS with N = 1, 2, 3, or 4. Set to 128
sampling frequency (fS), 256 fS, 384 fS, or 512 fS. Supports typical CMOS logic
levels from 1.8V up to 3.3V.
I2S Audio Data Inputs. These represent the eight channels of audio (two per
input) available through I2S. Supports typical CMOS logic levels from 1.8V up to
3.3V. See Figure 3 for timing details.
I2S Audio Clock input. Supports typical CMOS logic levels from 1.8V up to 3.3V.
Left/Right Channel signal input. Supports typical CMOS logic levels from1.8V up to
3.3V.
DSD audio data inputs. See Figure 5 for timing details.
DSD Clock input. This is a 2.8224MHz clock for the DSD audio inputs.
Power-Down Control and I2C Address Selection. The I2C address and the PD
polarity are set by the PD/AD pin state when the supplies are applied to the
ADV7511. Supports typical CMOS logic levels from 1.8V up to 3.3V.
Differential TMDS Clock Output. Differential clock output at pixel clock rate;
TMDS logic level.
Differential TMDS Output Channel 2. Differential output of the red data at 10
the pixel clock rate; TMDS logic level.
Differential TMDS Output Channel 1. Differential output of the green data at 10
Differential TMDS Output Channel 0. Differential output of the blue data at 10
Interrupt signal output. CMOS logic level. A 2 k pull-up resistor (10%) to
interrupt the microcontroller IO supply is recommended.
1.8V Power Supply for TMDS Outputs.
1.8V Power Supply for Digital and I/O Power Supply. These pins supply power to
the digital logic and I/Os. They should be filtered and as quiet as possible.
1.8V PLL Power Supply. These pins provide power to the digital portion of the
clock PLL. The designer should provide quiet, noise-free power to these pins.
1.8V PLL Power Supply. The most sensitive portion of the ADV7511 is the clock
generation circuitry. These pins provide power to the analog portion of the clock
PLL (VCO). The designer should provide quiet, noise-free power to these pins.
Band Gap Vdd.
208
AVR 2650
harman/kardon

Rev. PrB
47
18, 20, 22, 23,
27, 31, 37, 44,
46, 51, 75, 99,
100
56
MVDD
GND
P
P
3.3V Power Supply.

Ground. The ground return for all circuitry on-chip. It is recommended that the
ADV7511 be assembled on a single, solid ground plane with careful attention
given to ground current paths.
SDA
55
SCL
54
DDCSDA
53
DDCSCL
50
48
CEC_CLK
CEC_IO
I
I/O
Serial Port Data I/O. This pin serves as the serial port data I/O slave for register
access. Supports CMOS logic levels from 1.8V to 3.3V.
Serial Port Data Clock input. This pin serves as the serial port data clock slave for
register access. Supports CMOS logic levels from 1.8V to 3.3V.
Serial Port Data I/O to Sink. This pin serves as the master to the DDC bus. Tolerant
of 5 V CMOS logic levels.
Serial Port Data Clock to Sink. This pin serves as the master clock for the DDC
bus. Tolerant of 5 V CMOS logic levels.
CEC clock. From 1MHz to 100Mhz. Supports CMOS logic levels from 1.8V to 5V.
CEC data signal. Supports CMOS logic levels from 1.8V to 5V.
1.
I = input, O = output, P = power supply, C = control
209
AVR 2650
harman/kardon
Data Sheet
DUAL LOW NOISE OPERATIONAL AMPLIFIERS
AZ4580
Pin Configuration
Q Package
(SIP-8)
P/M/G Package
(DIP-8/SOIC-8/TSSOP-8)
VCC
OUTPUT 2
OUTPUT 1
VCC
INPUT 2-
INPUT 1-
OUTPUT 2
INPUT 2+
INPUT 1+
INPUT 2-
VEE
INPUT 2+
INPUT 1+
INPUT 1-
VEE
OUTPUT 1
Figure 2. Pin Configuration of AZ4580 (Top View)
Pin Description
Pin No.
Function
Pin No.
Function
Pin No.
Function
Pin No.
Function
OUTPUT 1
INPUT 1-
INPUT 1+
VEE
INPUT 2+
INPUT 2-
OUTPUT 2
VCC
210
AVR 2650
harman/kardon
CS42528
114 dB, 192 kHz 8-Ch Codec with S/PDIF Receiver
Features
General Description
Eight 24-bit D/A, two 24-bit A/D Converters

114 dB DAC / 114 dB ADC Dynamic Range
-100 dB THD+N
System Sampling Rates up to 192 kHz
S/PDIF Receiver Compatible with EIAJ CP1201
and IEC-60958
Recovered S/PDIF Clock or System Clock
Selection
8:2 S/PDIF Input MUX
ADC High-pass Filter for DC Offset Calibration
Expandable ADC Channels and One-line Mode
Support
Digital Output Volume Control with Soft Ramp
Digital +/-15dB Input Gain Adjust for ADC
Differential Analog Architecture
Supports logic levels between 5 V and 1.8 V.
TXP
RXP0
RXP1/GPO1
RXP2/GPO2
RXP3/GPO3
RXP4/GPO4
RXP5/GPO5
RXP6/GPO6
RXP7/GPO7
VARX
The CS42528 codec provides two analog-to-digital and eight

digital-to-analog delta-sigma converters, as well as an integrated S/PDIF receiver, in a 64-pin LQFP package.
The CS42528 integrated S/PDIF receiver supports up to eight
inputs, clock recovery circuitry and format auto-detection. The
internal stereo ADC is capable of independent channel gain
control for single-ended or differential analog inputs. All eight
channels of DAC provide digital volume control and differential
analog outputs. The general purpose outputs may be driven
high or low, or mapped to a variety of DAC mute controls or
ADC overflow indicators.
The CS42528 is ideal for audio systems requiring wide dynamic range, negligible distortion and low noise, such as A/V
receivers, DVD receivers, digital speaker and automotive audio
systems.
CS42528-CQZ
CS42528-DQZ
CDB42528
AGND LPFLT
-10 to 70 C 64-pin LQFP

-40 to 85 C 64-pin LQFP
Evaluation Board
DGND DGND VD
VD
INT
Rx
Clock/Data
Recovery
C&U Bit
Data Buffer
S/PDIF
Decoder
Control
Port
Form at
Detector
FILT+
VQ
REFGND
VA
AGND
OM CK
M UTE
DEM
AINL+
AINL-
ADC#1
Digital Filter
Gain & Clip
AINR+
AINR-
ADC#2
Digital Filter
Gain & Clip
M ult/Div
RM CK
Serial
Audio
Interface
Port
Internal M CLK
Ref
AOUTA1+
AOUTA1-
SAI_LRCK
ADCIN1
ADCIN2
CX_LRCK
CX_SCLK
DAC#3
CX_SDIN1
DAC#4
DAC#5
AOUTB3+
AOUTB3-
DAC#6
AOUTA4+
AOUTA4-
DAC#7
AOUTB4+
AOUTB4-
DAC#8

Cirrus Logic, Inc.
211
Volum e Control
Digital Filter
CX_SDIN2
Analog Filter
AOUTA3+
AOUTA3-
SAI_SDOUT
CX_SDO UT
DAC#2
AOUTA2+
AOUTA2-
SAI_SCLK
VLS
ADC
Serial
Data
DAC#1
AOUTB1+
AOUTB1-
AOUTB2+
AOUTB2-
AD0/CS
AD1/CDIN
SDA/CDOUT
SCL/CCLK
VLC
GPO
M UTEC
RST
CODEC
Serial
Port
CX_SDIN3
CX_SDIN4
Lead Free
Lead Free
AVR 2650
harman/kardon
CS42528
TXP
RXP0
VD
VLS
DGND
SAI_SDOUT
RMCK
CX_SDOUT
ADCIN2
ADCIN1
OMCK
SAI_LRCK
CX_SDIN4
SAI_SCLK
CX_SDIN2
CX_SDIN3
2. PIN DESCRIPTIONS
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
CX_SDIN1
48
RXP1/G PO 1
CX_SCLK
47
RXP2/G PO 2
CX_LRCK
46
RXP3/G PO 3
VD
45
RXP4/G PO 4
DGND
44
RXP5/G PO 5
VLC
43
RXP6/G PO 6
SCL/CCLK
42
RXP7/G PO 7
SDA/CDO UT
41
VARX
AD1/CDIN
CS42528
40
AG ND
AD0/CS
10
39
LPFLT
MUTEC
INT
11
38
RST
12
37
AO UTA1-
AINR-
13
36
AOUTA1+
AINR+
14
35
AOUTB1+
AINL+
15
34
AO UTB1-
AINL-
16
33
AO UTA2-
AOUTA2+
AOUTB2-
AOUTB2+
AOUTA3-
AOUTA3+
AOUTB3+
AOUTB3-
AGND
VA
AOUTA4-
AOUTA4+
AOUTB4+
REFGND
AOUTB4-
VQ
FILT+
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Pin Name
Pin Description
CX_SDIN1
CX_SDIN2
CX_SDIN3
CX_SDIN4
1
64
63
62
Codec Serial Audio Data Input (Input) - Input for twos complement serial audio data.
CX_SCLK
CODEC Serial Clock (Input/Output) - Serial clock for the CODEC serial audio interface.
CX_LRCK
CODEC Left Right Clock (Input/Output) - Determines which channel, Left or Right, is currently active on
the CODEC serial audio data line.
VD
4
51
Digital Power (Input) - Positive power supply for the digital section.
DGND
5
52
Digital Ground (Input) - Ground reference. Should be connected to digital ground.
VLC
Control Port Power (Input) - Determines the required signal level for the control port.
SCL/CCLK
Serial Control Port Clock (Input) - Serial clock for the serial control port. Requires an external pull-up
resistor to the logic interface voltage in I2C mode as shown in the Typical Connection Diagram.
SDA/CDOUT
Serial Control Data (Input/Output) - SDA is a data I/O line in I2C mode and requires an external pull-up
resistor to the logic interface voltage, as shown in the Typical Connection Diagram. CDOUT is the output
data line for the control port interface in SPI mode.
AD1/CDIN
Address Bit 1 (I2C)/Serial Control Data (SPI) (Input) - AD1 is a chip address pin in I2C mode; CDIN is
the input data line for the control port interface in SPI mode.
212
AVR 2650
harman/kardon
CS42528
AD0/CS
10
Address Bit 0 (I2C)/Control Port Chip Select (SPI) (Input) - AD0 is a chip address pin in I2C mode; CS
is the chip select signal in SPI mode.
INT
11
Interrupt (Output) - The CS42528 will generate an interrupt condition as per the Interrupt Mask register.
See Interrupts on page 40 for more details.
RST
12
Reset (Input) - The device enters a low power mode and all internal registers are reset to their default
settings when low.
AINRAINR+
13
14
Differential Right Channel Analog Input (Input) - Signals are presented differentially to the delta-sigma
modulators via the AINR+/- pins.
AINL+
AINL-
15
16
Differential Left Channel Analog Input (Input) - Signals are presented differentially to the delta-sigma
modulators via the AINL+/- pins.
VQ
17
Quiescent Voltage (Output) - Filter connection for internal quiescent reference voltage.
FILT+
18
Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling circuits.
REFGND
19
Reference Ground (Input) - Ground reference for the internal sampling circuits.
AOUTA1 +,AOUTB1 +,AOUTA2 +,AOUTB2 +,AOUTA3 +,AOUTB3 +,AOUTA4 +,AOUTB4 +,-
36,37 Differential Analog Output (Output) - The full-scale differential analog output level is specified in the
35,34 Analog Characteristics specification table.
32,33
31,30
28,29
27,26
22,23
21,20
VA
VARX
24
41
Analog Power (Input) - Positive power supply for the analog section.
AGND
25
40
Analog Ground (Input) - Ground reference. Should be connected to analog ground.
MUTEC
38
Mute Control (Output) - The Mute Control pin outputs high impedance following an initial power-on condition or whenever the PDN bit is set to a 1, forcing the codec into power-down mode. The signal will
remain in a high impedance state as long as the part is in power-down mode. The Mute Control pin goes
to the selected active state during reset, muting, or if the master clock to left/right clock frequency ratio
is incorrect. This pin is intended to be used as a control for external mute circuits to prevent the clicks
and pops that can occur in any single supply system. The use of external mute circuits are not mandatory but may be desired for designs requiring the absolute minimum in extraneous clicks and pops.
LPFLT
39
PLL Loop Filter (Output) - An RC network should be connected between this pin and ground.
RXP7/GPO7
RXP6/GPO6
RXP5/GPO5
RXP4/GPO4
RXP3/GPO3
RXP2/GPO2
RXP1/GPO1
42
43
44
45
46
47
48
S/PDIF Receiver Input/ General Purpose Output (Input/Output) - Receiver inputs for S/PDIF encoded
data. The CS42528 has an internal 8:2 multiplexer to select the active receiver port, according to the
Receiver Mode Control 2 register. These pins can also be configured as general purpose output pins,
ADC Overflow indicators or Mute Control outputs according to the RXP/General Purpose Pin Control
registers.
RXP0
49
S/PDIF Receiver Input (Input) - Dedicated receiver input for S/PDIF encoded data.
TXP
50
S/PDIF Transmitter Output (Output) - S/PDIF encoded data output, mapped directly from one of the
receiver inputs as indicated by the Receiver Mode Control 2 register.
VLS
53
Serial Port Interface Power (Input) - Determines the required signal level for the serial port interfaces.
SAI_SDOUT
54
Serial Audio Interface Serial Data Output (Output) - Output for twos complement serial audio PCM
data from the S/PDIF incoming stream. This pin can also be configured to transmit the output of the internal and external ADCs.
RMCK
55
Recovered Master Clock (Output) - Recovered master clock output from the External Clock Reference
(OMCK, pin 59) or the PLL which is locked to the incoming S/PDIF stream or CX_LRCK.
18
213
DS586PP5
AVR 2650
harman/kardon
CS42528
CX_SDOUT
56
CODEC Serial Data Output (Output) - Output for twos complement serial audio data from the internal
and external ADCs.
ADCIN1
ADCIN2
58
57
External ADC Serial Input (Input) - The CS42528 provides for up to two external stereo analog to digital
converter inputs to provide a maximum of six channels on one serial data output line when the CS42528
is placed in One Line mode.
OMCK
59
External Reference Clock (Input) - External clock reference that must be within the ranges specified in
the register OMCK Frequency (OMCK Freqx) on page 54.
SAI_LRCK
60
Serial Audio Interface Left/Right Clock (Input/Output) - Determines which channel, Left or Right, is
currently active on the serial audio data line.
SAI_SCLK
61
Serial Audio Interface Serial Clock (Input/Output) - Serial clock for the Serial Audio Interface.
214
AVR 2650
harman/kardon
CS4970x4 Data Sheet

FEATURES
High Definition Audio Decoder DSP
Family with Dual 32-bit DSP Engine Technology
Multi-standard 32-bit High Definition Audio Decoding plus

Post-Processing
Supports high-definition audio formats including:
Dolby Digital Plus
Dolby TrueHD
Up to 12 Channels of 32-bit Serial Audio Input
DTS-HD High Resolution Audio
Customer Software Security Keys

16 Ch x 32-bit PCM Out with Dual 192 kHz SPDIF Tx
DTS-HD Master
Audio
Two SPI/I2C ports

One Parallel Port (144-pin LQFP package only)
Large On-chip X, Y, and Program RAM & ROM
SDRAM and Serial Flash Memory Support
DTS Express
Additional Applications Library
Dolby Digital EX, Dolby Pro Logic IIz, Dolby
Headphone 2, Dolby Virtual Speaker 2, Audistry
DTS-ES 96/24 Discrete 7.1, DTS-ES Discrete 7.1, DTSES Matrix 6.1, DTS Neo:6, DTS Neural Surround
DSD
MPEG-2 AAC LC 5.1
SRS CS2, SRS TruVolume, SRS TruSurround
HD4, WOW HD,
THX Ultra2, THX ReEQ
Thomson MP3 Surround
Audyssey 2EQ Module
The CS4970x4 DSP family is an enhanced version of the

CS4953x DSP family with higher overall performance. In
addition to all the mainstream audio processing codes in onchip ROM that the CS4953x DSP offers, the CS4970x4 device
family also supports the decoding of major high-definition
audio formats. Additionally, the CS4970x4, a dual-core device,
performs the high-definition audio decoding on the first core,
leaving the second core available for audio post-processing and
audio enhancement. The CS4970x4 device supports the most
demanding audio post processing requirements. It provides an
easy upgrade path to systems currently using the CS495xx or
CS4953x device with minor hardware and software changes.
Cirrus Logics Applications Library

Cirrus Original Multi-Channel Surround 2 (COMS2),
Cirrus Band Xpander, Cirrus Virtualization Technology,
Cirrus Intelligent Room Calibration 2 (IRC2)
Crossbar Mixer, Signal Generator
Advanced Post-Processors including: 7.1 Bass Manager,
Tone Control, 11- Band Parametric EQ, Delay, 2:1/4:1
Decimator, 1:2/1:4 Upsampler
Serial
Control 1
Serial
Control 2
See page 28 for ordering information.
Parallel
Control
GPIO
Debug
12 Ch. Audio In /
6 Ch. SACD In
STC
D
M
A
Coyote 32-bit
DSP A
S/PDIF
S/PDIF
Coyote 32-bit
DSP B
TMR1
TMR2
16 Ch PCM
Audio Out
Ext. Memory Controller
PLL
This document contains information for a new product.

Cirrus Logic reserves the right to modify this product without notice.
Copyright 2009 Cirrus Logic
215
Nov 09
DS752PP8
AVR 2650
harman/kardon
CS4970x4 Data Sheet
32-bit High Definition Audio Decoder DSP Family
8. Device Pin-Out Diagram
GPIO38, PCP_WR# / DS#, SCP2_CLK
SD_A10, EXT_A10
SD_BA0, EXT_A13
SD_BA1, EXT_A14
105 GNDIO5
SD_WE#
SD_CAS#
SD_RAS#
EXT_A15
110 SD_CS#
VDD5
EXT_A16
EXT_A17
EXT_A18
115 GND5
EXT_A19
EXT_OE#
EXT_CS1#
RESET#
120 VDDIO6
GNDIO6
GPIO33, SCP1_MOSI
GPIO34, SCP1__MISO / SDA
GPIO35, SCP1_CLK
125 VDD6
GND6
GPIO37, SCP1_BSY#, PCP_BSY#
8.1 128-Pin LQFP Pin-Out Diagram
SD_A0, EXT_A0
GPIO11, PCP_A3, AS#, SCP2_MISO / SDA
SD_A1, EXT_A1
100 VDDIO5
GPIO10, PCP_A2 / A10, SCP2_MOSI
SD_A2, EXT_A2
GPOI9, SCP1_IRQ#
GPIO8, PCP_IRQ#, SCP2_IRQ#
GND4
SD_A3, EXT_A3
GPIO7, SCP1_CS#, IOWAIT
SD_A4, EXT_A4
GPIO6, PCP_CS#, SCP2_CS#
95 VDD4
VDDIO7
EXT_CS2#
GNDIO7
SD_A5, EXT_A5
GPIO3, DDAC 10
GNDIO4
GPIO2
VDD7
SD_A6, EXT_A6
GPIO1
90 SD_A7, EXT_A7
VDDIO4
GPIO0, EE_CS#
SD_A8, EXT_A8
GND7 15
SD_A9, EXT_A9
XTAL_OUT
GND3
XTI
85 SD_A11, EXT_A11
XTO
CS497xx4
GNDA
PLL_REF_RES 20
SD_A12, EXT_A12
VDD3
128-Pin LQFP
VDDA (3.3V)
VDD8
SD_CLKEN
SD_CLKIN
80 SD_CLKOUT
SD_DQM1
SD_D8, EXT_D8
GND8 25
SD_D9, EXT_D9
GNDIO3
DAI1_DATA0, TM0, DSD0
75 SD_D10, EXT_D10
VDDIO8
SD_D11, EXT_D11
DAI1_SCLK, DSD_CLK
VDDIO3
DAI1_LRCLK, DSD4 30
SD_D12, EXT_D12
GNDIO8
SD_D13, EXT_D13
GPIO42, BDI_REQ# , DAI2_LRCLK, PCP_IRQ# / BSY#
70 SD_D14, EXT_D14
GPIO43, BDI_CLK, DAI2_SCLK
SD_D15, EXT_D15
BDI_DATA, DAI2_DATA, DSD5
SD_D0, EXT_D0
GPIO26, DAO2_DATA3 / XMTB 35
GNDIO2
DBDA
EXT_WE#
DBCK
65 SD_D1, EXT_D1
SD_D2, EXT_D2
SD_D3, EXT_D3
VDDIO2
SD_D4, EXT_D4
SD_D5, EXT_D5 60
SD_D6, EXT_D6
SD_D7, EXT_D7
SD_DQM0
GND2
VDD2 55
GNDIO1
DAO1_LRCLK
DAO1_SCLK
DAO1_DATA0, HS0
VDDIO1 50
GND1 45
GPIO23,
DAO2_LRCLK
GPIO17, DAO1_DATA3 / XMTA
GPIO22, DAO2_SCLK
VDD1
TEST
DAO_MCLK 40
GPIO20, DAO2_DATA2
Figure 19. 128-Pin LQFP Pin-Out Diagram

DS752PP8
Copyright 2009 Cirrus Logic
216
29
AVR 2650
harman/kardon
KIA1117BS/BF00~
KIA1117BS/BF50
SEMICONDUCTOR
TECHNICAL DATA
BIPOLAR LINEAR INTEGRATED CIRCUIT
LOW DROP FIXED AND ADJUSTABLE

POSITIVE VOLTAGE REGULATOR
A
H
The KIA1117BS/BF
Series are a Low Drop Voltage Regulator able
to provide up to 1A of output current, available even in adjustable
version (Vref=1.25V)
J
G
FEATURES
Low Dropout Voltage : 1.1V/Typ. (Iout=1.0A)

Very Low Quiescent Current : 2.5 /Typ.
1
DIM
A
Output Current up to 1A
MILLIMETERS
_
6.5 + 0.2
_
3.5 + 0.2
Fixed Output Voltage of 1.2V, 1.5V, 1.8V, 2.5V, 2.85V, 3.3V, 5.0V
Adjustable Version Availability : Vref=1.25V
1.8 MAX
D
E
0.7+0.15/-0.1
_
7 + 0.3
Internal Current and Thermal Limit
1. GND (Adj.)
F
G
2.3 TYP
0.26+0.09/-0.02
A Minimum of 10
2. OUTPUT
3. INPUT
J
K
L
3.0+0.15/-0.1
_
1.75 + 0.25
for stability
Suitable for MLCC, Tantalum and Low ESR Electrolytic Capacitors
Heat Sink is common to

2 (Output)
ESR Range for stability : 1m ~200

Available in
2%(at 25 )
SOT-223
High Ripple Rejection : 80dB/Typ

Temperature Range : -40
150
LINE UP
ITEM
OUTPUT VOLTAGE (V)
KIA1117BS/BF00
Adjustable (1.25~8V)
KIA1117BS/BF12
1.2
KIA1117BS/BF15
1.5
KIA1117BS/BF18
1.8
S : SOT-223
KIA1117BS/BF25
2.5
F : DPAK
KIA1117BS/BF28
2.85
KIA1117BS/BF33
3.3
KIA1117BS/BF50
5.0
MAXIMUM RATINGS (Ta=25

CHARACTERISTIC
PACKAGE
)
SYMBOL
RATING
UNIT
Input Voltage
VIN
10
Output Current
IOUT
1.0
Power Dissipation 1
S (Note)
(No Heatsink)
Power Dissipation 2
(Infinite Heatsink)
PD1
PD2
1.0
W
1.3
8.3
W
13
Maximum Junction Temperature
Tj(max)
150
Operating Junction Temperature
Topr
-40 150
Storage Temperature
Tstg
-55 150
Note) Package Mounted on FR-4 PCB 36 18
1.5
217
0.1 MAX
10 MAX
AVR 2650
harman/kardon
KIC3201S/T-12 ~
KIC3201S/T-60
SEMICONDUCTOR
TECHNICAL DATA
CMOS Linear Integrated Circuit
Large Current Positive Voltage Regulator

A
H
G
J
B
E
The KIC3201S/T series are highly precise, low power consumption,

positive voltage regulators manufactured using CMOS and laser trimming
technologies. The series provides large currents with a significantly small
dropout voltage. The KIC3201S/T consists of a driver transistor, a
precision reference voltage and an error amplifier. Output voltage is
selectable in 0.05V steps between a voltage of 1.2V and 6.0V.
DIM
A
B
C
D
E
F
G
H
J
K
D
K
Features
Maximum Output Current : 400mA
Dropout Voltage : 150mV @100mA, 300mV @200mA for VOUT=3.0V
Maximum Operating Voltage : 10V
Output Voltage Range :
1.2V ~ 6.0V (selectable in 0.05V steps)
Highly Accurate : 2%
Low Power Consumption : Typ. 8.0uA
Operational Temperature Range : -40 ~ 85
Low ESR Capacitor : Ceramic compatible or Tantalum
Applications
Battery Powered Equipment
Reference Voltage Sources
Digital Cameras, Camcoders
Palmtop Computers
Portable Audio Video Equipment
Pin Configuration
KIC3201S-XX
Lot No.
No.
Type Name
1
GND
VIN
VOUT
SOT-89
(TOP VIEW)
Symbol
GND
VIN
VOUT
Description
Ground
Power input
Output
(VIN)
218
MILLIMETERS
4.70 MAX
_
2.50 + 0.20
1.70 MAX
0.45+0.15/-0.10
4.25 MAX
_
1.50 + 0.10
0.40 TYP
1.75 MAX
0.75 MIN
0.5+0.10/-0.05
1 GND
2 VIN
3 VOUT
Heat Sink is common

to 2 (VIN)
SOT-89
AVR 2650
harman/kardon
SEMICONDUCTOR
KTC812T
TECHNICAL DATA
EPITAXIAL PLANAR NPN TRANSISTOR
FOR MUTING AND SWITCHING APPLICATION.

FEATURES
E
K
High Emitter-Base Voltage : VEBO=25V(Min.)
DIM
A
B
C
D
E
High Reverse hFE
F
G
: Reverse hFE=150(Typ.) (VCE=-2V, IC=-4mA)

Low on Resistance : RON=1 (Typ.), (IB=5mA)
MILLIMETERS
_
2.9 + 0.2
1.6+0.2/-0.1
_
0.70 + 0.05
_
0.4 + 0.1
2.8+0.2/-0.3
_
1.9 + 0.2
0.95
UNIT
VCBO
50
Collector-Base Voltage
RATING
SYMBOL
Collector-Emitter Voltage
VCEO
20
Emitter-Base Voltage
VEBO
25
Collector Current
IC
300
mA
Base Current
IB
60
mA
PC *
0.9
mW
Tj
150
Tstg
0.60
0.55
CHARACTERISTIC
0.25+0.25/-0.15
K
L
_
0.16 + 0.05
0.00-0.10
MAXIMUM RATING (Ta=25
H
I
-55 150
Collector Power Dissipation

Junction Temperature
Storage Temperature Range
* Package mounted on a ceramic board (600
0.8
1. Q 1
2. Q 1
3. Q 2
4. Q 2
5. Q 2
6. Q 1
EMITTER
BASE
COLLECTOR
EMITTER
BASE
COLLECTOR
TS6
EQUIVALENT CIRCUIT (TOP VIEW)

6
Marking
Lot No.
h FE Rank
Q1
Type Name
Q2
ELECTRICAL CHARACTERISTICS (Ta=25

CHARACTERISTIC
SYMBOL
TEST CONDITION
MIN.
TYP.
MAX.
UNIT
Collector Cut-off Current
ICBO
VCB=50V, IE=0
0.1
Emitter Cut-off Current
IEBO
VEB=25V, IC=0
0.1
DC Current Gain
hFE
VCE=2V, IC=4mA
350
1200
VCE(sat)
IC=30mA, IB=3mA
0.042
0.3
Base-Emitter Voltage
VBE
VCE=2V, IC=4mA
0.61
Transition Frequency
fT
VCE=6V, IC=4mA
30
MHz
4.8
pF
160
500
130
Turn-on Time
INPUT
Storage Time
tstg
tf
Note : hFE Classification
2002. 12. 5
OUTPUT
ton
Fall Time
Time
VCB=10V, IE=0, f=1MHz
4k
10V
50
Switching
Cob
1k
Collector Output Capacitance
3k
Collector-Emitter Saturation Voltage
1s
DUTY CYCLE < 2%
=
VBB =-3V
VCC =12V
nS
B: 350 1200
Revision No : 1
219
1/3
AVR 2650
harman/kardon
NJU7751/54
LOW DROPOUT VOLTAGE REGULATOR
GENERAL DISCRIPTION
NJU7751/54 is a low dropout voltage regulator with
ON/OFF control and Output shunt switch.
Advanced CMOS technology achieves high ripple rejection
and ultra low quiescent current.
It is suitable for reset small micro controller and other logic
chips.
PACKAGE OUTLINE
NJU7751/54F
FEATURES
Ultra Low quiescent Current
Iq=20A typ.(IO=0mA)
Output capacitor with 1.0uF ceramic capacitor
Output Current
IO(max.)=100mA
High Precision Output
VO1.0%
Low Dropout Voltage
0.15V typ. (IO=60mA, VO=3V)
With ON/OFF Control
(Active High)
With Output Shunt Switch
Internal Short Circuit Current Limit
CMOS Technology
Package Outline
SOT-23-5
PIN CONFIGURATION
PIN FUNCTION
5
4
1.CONTROL
2.GND
3.N.C.
4.VOUT
1 2 3
5.VIN
NJU7751/54F
EQUIVALENT CIRCUIT
VIN
CONTROL
VOUT
Output
Control
VIN
CONTROL
Vref
Current
Limit
GND
VOUT
Output
Control
Vref
Current
Limit
GND
NJU7751
NJU7754
OUTPUT VOLTAGE RANK LIST

DEVICE NAME
VOUT
NJU775*F21
2.1V
NJU775*F25
2.5V
NJU775*F03
3.0V
NJU775*F33
3.3V
NJU775*F05
5.0V
220
Ver.2004-12-22
-1-
AVR 2650
harman/kardon
SEMICONDUCTOR
KIA278R05PI~KIA278R15PI
TECHNICAL DATA
4 TERMINAL 2A OUTPUT LOW DROP

VOLTAGE REGULATOR
C
The KIA278R
Series are Low Drop Voltage Regulator
suitable for various electronic equipments.
It provides constant voltage power source with TO-220 4 terminal
lead full molded PKG. The Regulator has multi function such as
over current protection, overheat protection and ON/OFF control.
L
K
U
FEATURES
2.0A Output Low Drop Voltage Regulator.
Built in ON/OFF Control Terminal.

Built in Over Current Protection, Over Heat
DIM MILLIMETERS
_
A
10.00 + 0.20
_
15.00 + 0.20
B
_
C
2.70 + 0.20
_
D
0.60 + 0.10
_
E
3.20 + 0.20
_
3.50 + 0.10
F
_
15.70 + 0.20
G
_
H
0.40 + 0.10
14.3+0.2/-0.1
J
_
1.45 + 0.10
K
_
L
1.00 + 0.10
2.54
M
_
N
4.50 + 0.20
_
O
7.5+ 0.1
_
1.50 + 0.10
P
R
S
T
U
V
Protection Function.
1
2
3
4
P
1
LINE UP
ITEM
OUTPUT VOLTAGE (Typ.)
KIA278R05PI
KIA278R06PI
KIA278R10PI
10
KIA278R12PI
12
* KIA278R15PI
DC INPUT (V IN )
DC OUTPUT (VO )
GND
ON/OFF CONTROL
KIA278R09PI
_
3-1.00 + 0.1
_
1.30 + 0.1
KIA278R08PI
5
8
_
1.30 + 0.1
UNIT
15
TO-220IS-4
* Note) * : Under Development.
MAXIMUM RATING (Ta=25

CHARACTERISTIC
)
SYMBOL
RATING
UNIT
Remark
Input Voltage
VIN
35
ON/OFF Control Voltage
VC
35
Output Current
IO
Power Dissipation 1
Pd1
1.5
No heatsink
Power Dissipation 2
Pd2
15
with heatsink
Tj
125
Operating Temperature
Topr
-20
80
Storage Temperature
Tstg
-30
125
Soldering Temperature (10sec)
Tsol
260
221
AVR 2650
harman/kardon
KIA78R000F/PI~
KIA78R050F/PI
SEMICONDUCTOR
TECHNICAL DATA
4 ,5 TERMINAL LOW DROP VOLTAGE REGULATOR

[Low Quiescent Current-Type]
C
The KIA78R
F/PI Series are Low Dropout Voltage
Regulator suitable for various electronic equipments.
The Regulator has multi function such as over current protection,
overheat protection.
FEATURES
L
K
U
1.0A Output Low Drop Voltage Regulator.
Built in ON/OFF Control Terminal. (Active High)

Built in Over Current Protection, Over Heat Protection Function.
DIM MILLIMETERS
_
A
10.00 + 0.20
_
15.00 + 0.20
B
_
C
2.70 + 0.20
_
D
0.60 + 0.10
_
E
3.20 + 0.20
_
3.50 + 0.10
F
_
15.70 + 0.20
G
_
H
0.40 + 0.10
14.3+0.2/-0.1
J
_
1.45 + 0.10
K
_
L
1.00 + 0.10
2.54
M
_
N
4.50 + 0.20
_
O
7.5+ 0.1
_
1.50 + 0.10
P
R
S
T
U
V
Low Quiescent Current (Output OFF mode) : 0.5 A(Typ.)

N
Low Standby Current : 800 A(Typ.)

P
1
LINE UP
ITEM
OUTPUT VOLTAGE (V)
PACKAGE
KIA78R000F/PI
Adjustable (1.25~15V)
KIA78R015F/PI
1.5
KIA78R018F/PI
1.8
KIA78R020F/PI
2.0
F : DPAK-5
KIA78R025F/PI
2.5
PI : TO-220IS-4
_
3-1.00 + 0.1
_
1.30 + 0.1
DC INPUT (V IN )
DC OUTPUT (VO )
GND
ON/OFF CONTROL (VC)
/ ADJUSTABLE
1
2
3
4
5
8
_
1.30 + 0.1
TO-220IS-4
3.0
KIA78R033F/PI
3.3
KIA78R050F/PI
5.0
KIA78R030F/PI
MAXIMUM RATINGS (Ta=25
CHARACTERISTIC
SYMBOL
RATING
16
UNIT
VIN
Input Voltage
VC
16
2 ON/OFF CONTROL (VC)
IOUT
3 DC OUTPUT (VO)
Output Current
Power Dissipation 1
(No heatsink)
PI
Power Dissipation 2
(Without heatsink)
PI
PD1
PD2
5 GND

5 (GND)
DPAK-5
13
W
15
Tj
150
Operating Temperature
Topr
-20 80
Storage Temperature
Tstg
-30 150
Soldering Temperature
Tsol
260
4 N.C / ADJUSTABLE
1.3
1.5
222
MILLIMETERS
_
6.6 + 0.2
_
6.1+ 0.2
_
5.0 + 0.2
_
1.10 + 0.2
_
2.70 + 0.2
_
1.27 + 0.1
0.5+0.2/-0.1
_
2.30 + 0.2
_
0.5 + 0.1
_
0.50 + 0.1
_
0.8 + 0.2
0 ~0.25
0.7MIN
_
1.00 + 0.1
1 DC INPUT (VIN )
1
ON/OFF Control Voltage
DIM
A
B
C
D
E
F
H
I
J
L
M
N
O
P
AVR 2650
harman/kardon
TRANSISTOR, REGULATOR IC BLOCK DIAGRAM

TO-92M
1. Emitter
2. Collector
3. Base
123
123
KTC2874B
KRA107M
KRA104MT
KTA1267
KSC2785Y
KRC107M
KRC104M
KTC 1027
TO-126
KTD1302T
KTC3200GR
KTA1271Y
KTC 3199
2SC2240BL
123
123
KTA1268GR
KTC3198Y
KSA1175YT
KTA1266YT
KRC102M
MCNJM7905
NJM7908
KIA 7908
KIA 7905
KTA1024Y
MC7915C
L7905
TO-3P
1. Base
2. Collector
3. Emitter
1. INPUT
2. GND
3. OUTPUT
123
KSA733CYT
MC7815C
MC7809
NJM7824
L7812
L7808
KSC2316Y
L7915
KIA7915
TO-220
123
2
1. Emitter
2. Collector
3. Base
1. GND
2. INPUT
3. OUTPUT
1. Emitter
2. Base
3. Collector
123
2
KTD600KG
KTA 1360
KTC 3423
1. Emitter
2. Collector
3. Base
TO-92
1. Emitter
2. Collector
3. Base
TO-92L
TO-220
TO-92
1 2 3
KIA 7809
KIA7815
MC7805C
L7805
L7815
KIA 7808
KIA7812
2SB1560 2SC3423O
2SD2390 2SB1559
2SA1360
2SD2389
2SB1647
2SD2560
KRA 107S
N-CHANNEL MOS FET ARRAY

PA672T
6
SOT-223 PKG (FRONT VIEW)
PIN CONFIGURATION
SOT-23 Package
LM1117
REGULATOR
AD1580
1. Source 1 (S1)
2. Gate 1 (G1)
3. Drain 2 (D2)
4. Source 2 (S2)
5. Gate 2 (G2)
6. Drain 1 (D1)
Marking: MA
V+ 1
3 NC (OR V)
V 2
TOP
VIEW
PIN FUNCTION
1. Adj/Gnd
2. Vout
3. Vin
NC = NO CONNECT
TO-263 (D2 PKG, FRONT VIEW)
PIN FUNCTION
1. Adj/Gnd
2. Vout
3. Vin
223
AVR 2650
harman/kardon
224
AVR 2650
harman/kardon
225
AVR 2650
harman/kardon
226
AVR 2650
harman/kardon
227
AVR 2650
harman/kardon
228
AVR 2650
harman/kardon
229
AVR 2650
230
harman/kardon
AVR 2650
harman/kardon
231
DVDD_1V8_3014
Worst Measured Currents

390mA
C104
C105
C111
0.1uF / 16V

24.3mA
L802
+1.8VH2
0.1uF_NC
#12: Added Pull-down 500 ohm
R604
R605
R618
R619
DVDD_1V8_3014
R606
R866
10K
R867
PVDD_1V8_3014
X901
47P
R620
47P
C145
10K
1K(1%)
2.2K
1K(1%)
R611
28.6363MHz
R610
HDMI_SDA
HDMI_SCL
ADV3014_INT
DVDDIO_3V3_3014
C144
ADV3014_INT2
R614
2.2K
DVDDIO_3V3_3014
ADV3014_INT_TX
C101
C103
25V/0.01UF
C141
C114
C127
25V/0.01UF
9R005Z
C143
100
100
79
78
R613
73
131
RXB_C-
132
RXB_C+
133
TVDD
134
RXB_0-
135
RXB_0+
136
CGND
137
RXB_1-
138
RXB_1+
TX0-
50
TXGND
49
TXC+
48
TXC-
47
TXGND
TVDD
140
RXB_2-
141
RXB_2+
45
44
TXDDC_SDA
43
TEST0
HP_CTRLC
5V_DETC
DDCC_SDA
46
TXAVDD
TXDDC_SCL
42
HP_TX
CVDD
CGND
TXPVDD
139
52
41
EXT_SWING
TXPLGND
TXPGND
TXPLVDD
40
142
RXD_2+
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
38
37
34
35
60
59
58
HDMI1_D2+
57
HDMI1_D256
TXAVDD_1V8_3014
55
HDMI1_D1+
54
HDMI1_D153
52
HDMI1_D0+
51
HDMI1_D050
+5VH1
49
HDMI1_CK+
48
HDMI1_CK47
46
45
R622
42
40
39
38
37
13
JK93
TXPLVDD_1V8_3014
TXPVDD_1V8_3014
CVDD_1V8_3014
1K
11
9
7
5
3
D22
JK96
D2+
R631
12
10
4
D1+
D2 SHIELD
HDMI3_D2+
D1-
D2 SHIELD
D0-
D2 SHIELD
HDMI3_D2-
D2-
CK+
D1 SHIELD
D0+
HDMI3_D1+
D1+
D1 SHIELD
HDMI3_D1-
D2 SHIELD
CK-
INPUT-5
HDMI3_D0+
CEC
13
11
HDMI3_D0-
D1-
14
NC
CE REMOTE
HDMI3_CK+
100
47K
15
DDC CLK
HDMI3_CK-
R652
R654
0.1uF
C146
16
DDC DATA
#7: Added pull-up
22K
R646
TVDD_3V3_3014
GND
DVDD_1V8_3014
+5V
D0+
KRC103S
R647
R650
19
16
10K_NC
19
HP DET
HDMI3_DDC_SDA
HDMI3_DDC_SCL
R633
D1 SHIELD
Q910
17
47K
D0-
HDMI_HPD1
#21: HPD Part
18
R656
10
CK+
KRA102S
1K
47K
R661
R635
1K
R639
1K
47K
0.1uF
12
CKD1 SHIELD
INPUT-2
PWR3
100
C148
14
NC
CE REMOTE
D2+
22K
15
DDC CLK
Q909
KRC103S
R634
17
GND
DDC DATA
41
36
HDMI_HPD3
R638
HDMI1_DDC_SDA
TMDS Signal Amplitude Circuit
Q901
18
+5V
HDMI1_DDC_SCL
R615
43
Q908 KRA102S
HP DET
R608
44
36
RXD_2-
14
35
TVDD
13
34
RXD_1+
12
33
11
32
10
31
RXD_1-
30
CGND
29
RXD_0+
28
RXD_0-
27
TVDD
26
RXD_C+
25
RXD_C-
24
23
CGND
144
22
143
CVDD
39
DVDD_1V8_3014
61
To : ADV7844 HDIM Input port
51
53
62
2.2K
TX0+
TX1TXGND
63
2.2K
CGND
54
64
R609
130
TX1+
CVIADV3014BSTZ
65
2.2K
CVDD
55
66
R623
DDCB_SCL
129
TXAVDD
67
R878
128
56
10K
DDCB_SDA
TX2-
IC901
R616
127
57
R601
DVDD
58
10K_NC
126
59
TX2+
R617
DGND
CEC
TXGND
10K_NC
125
60
10K
5V_DETB
61
DGND
R602
HP_CTRLB
124
DVDD
RXA_2-
68
10K
RXA_2+
123
TVDD
69
R865
122
62
70
1K(1%)
121
ALSB
DVDDIO_3V3_3014
71
8.2K(1%)
120
63
DVDDIO_3V3_3014
72
R621
74
75
76
77
TEST7
SCL
SDATA
TEST6
TEST5
DVDDIO
TEST8
DGND
80
DVDD
81
INT
82
INT2
83
INT_TX
84
DGNDDIO
85
86
87
DVDDIO
88
TEST9
89
TEST10
90
TEST11
91
TEST12
92
TEST13
94
93
DVDD
DGND
TEST14
95
TEST15
96
TEST16
97
RESETB
98
PWRDNB
XTAL
PVDD
XTAL1
PVDD
PGND
99
100
101
102
103
104
105
106
PGND
HP_CTRLA
DDCA_SDA
RTERM
5V_DETA
RXA_1+
64
CSB
DDCD_SCL
144
#21: HPD Part
119
EP_SCK
21
R857 : Front HDMI don`t used
143
RXA_1-
20
142
CGND
118
65
DDCD_SDA
141
117
EP_CS
19
140
RXA_0+
DVDD
139
116
66
18
138
69
67
DGND
137
70
68
5V_DETD
136
71
TEST1
HP_CTRLD
135
72
EP_MOSI
17
134
73
EP_MISO
16
133
74
TEST2
DGNDIO
TEST4
TEST3
15
132
23
75
DDCA_SCL
CVDD
CGND
RXC_2+
131
22
76
RXC_2-
130
77
TVDD
21
21
78
RXC_1+
129
20
79
RXA_0-
14
128
19
80
TVDD
13
127
18
81
RXA_C+
12
17
82
RXC_1-
126
83
RXA_C-
11
16
125
84
CGND
15
124
DVDD_1V8_3014
85
RXC_0+
123
15
86
RXC_0-
13
122
13
87
115
11
88
114
11
120
89
113
10
90
112
118
91
TVDD
117
0_NC
92
111
R858
93
RXC_C+
94
116
95
DDCC_SCL
CVDD
CGND
10
107
108
R645
47K_NC
96
RXC_C-
115
97
1K_NC
47K_NC
R643
L866
9R005Z_NC
R640
0.1uF_NC
C149
114
100_NC
98
110
1K_NC
4
7
R644
R641
99
109
D2+
D2 SHIELD
113
22K_NC
R642
14
22
JK94
HDMI2_D2+
112
121
12
D2-
D2 SHIELD
D1+
D2 SHIELD
111
10K
HDMI2_D2-
D2-
D1 SHIELD
110
R857
HDMI2_D1+
D1+
D0+
D1-
D2 SHIELD
D0-
109
12
17
HDMI2_D1-
D1-
CK+
D1 SHIELD
10K
10
19
8
7
D0+
HDMI2_D0+
CK-
108 107 106 105 104 103 102 101 100

R603
Q911 KRC103S_NC
119
23
HDMI2_D0-
D0-
CK SHIELD
#21: HPD Part
14
HDMI2_CK+
10
CK+
D1 SHIELD
FRONT_HDMI
HDMI2_CK-
GND
CEC
16
19
#7: Added pull-up
11
D1 SHIELD
+3.3VA
+3.3VA
12
CK-
+5VA
HDMI2_DDC_SDA
TXEN
+5V
HDMI2_DDC_SCL
13
CE REMOTE
DDC CLK
10K_NC
14
NC
DDC DATA
PWR2
100
18
47K
0.1uF
R632
15
DDC CLK
INPUT-3
C151
16
DDC DATA
D2+
R657
R655
17
GND
22K
R659
18
+5V
Q912 KRA102S_NC
1
2
CE REMOTE
HDMI_HPD2
HP DET
HP DET
KRC103S
TX_EN
+5VA +3.3VH2
20
R658
R636
Q902
1K
R660
KRA102S
1K
47K
Q903
Option : Front HDMI Input port
9R005Z_NC
L865
#21: HPD Part
CN63
CJP23GB210ZY NC
R612
DVDDIO_3V3_3014
R607
C140
C136
0.1uF / 16V
25V/0.01UF
C129
C132
10uF/6.3V
25V/0.01UF
C138
C118
C112
C137
0.1uF / 16V
25V/0.01UF
C139
10uF/6.3V

4.33mA
L801
+1.8VH2
9R005Z
C142
C128
0.1uF / 16V
C124
C130
25V/0.01UF
C123
C126
0.1uF / 16V
25V/0.01UF
C106
C125
0.1uF / 16V
25V/0.01UF
0.1uF / 16V
25V/0.01UF
C102
C109
0.1uF / 16V
C121
10uF/6.3V
0.1uF / 16V
C133
C135
25V/0.01UF
C110
C134
0.1uF / 16V
25V/0.01UF
C107
C108
0.1uF / 16V

2.3mA
L804
9R005Z
10uF/6.3V
+3.3VH2
TXPLVDD_1V8_3014
0.1uF / 16V

238mA
L806
9R005Z
harman/kardon
3.3V Total : 240.3mA
9R005Z
TXPVDD_1V8_3014
DVDDIO_3V3_3014
0.1uF / 16V
+3.3VH2
25V/0.01UF
C120
10uF/6.3V
C117
C131
25V/0.01UF
C115
C122
0.1uF / 16V
25V/0.01UF
C113
C116
0.1uF / 16V
25V/0.01UF
0.1uF / 16V
C119
10uF/6.3V
TVDD_3V3_3014
AVR 2650
1.8V Total : 904.33mA

22.7mA
L807
+1.8VH2
9R005Z
0.1uF / 16V
9R005Z
9R005Z

35mA
L808
+1.8VH2
10uF/6.3V
L805
0.1uF / 16V
+1.8VH2
10uF/6.3V

428mA
TXAVDD_1V8_3014
0.1uF / 16V
CVDD_1V8_3014
L803
PVDD_1V8_3014
CUP12328Z
ADV7844 Worst Measured Currents
ADV3014 Decoupling Capacitor
+1.8VH2
ADV3014_RESET
CEC
#21: HPD Part

Q905 KRA102S
10K_NC
DDC DATA
HDMI4_DDC_SCL
HDMI4_D2+
JK92
1K
R637
R627
15
12
11
REVISION
2
3
8
7
D0+
D2 SHIELD
D1+
SCHEMATIC DIAGRAM
M/P
3
2
D2 SHIELD
D2+
CEC
10
D0-
D2-
D2 SHIELD
HDMI4_D2-
D2-
100
47K
HDMI4_D1+
D1+
CK+
D1 SHIELD
D1-
D2 SHIELD
0.1uF
D1-
HDMI4_D1-
D1 SHIELD
JK95
D0+
INPUT-4
11
9
HDMI4_D0+
HDMI4_D0-
D0D1 SHIELD
13
CE REMOTE
CK-
HDMI4_CK+
10
CK+
R648
R625
C150
14
NC
#7: Added pull-up

HDMI4_CK-
12
CKD1 SHIELD
19
GND
KRC103S
22K
R649
18
+5V
HDMI4_DDC_SDA
DDC CLK
13
CE REMOTE
1K
47K
R651
17
47K
14
NC
INPUT-1
R628
15
DDC CLK
HP DET
PWR4
100
0.1uF
Q904
SHEET
16
DDC DATA
D2+
R629
C147
#21: HPD Part
16
17
GND
22K
18
+5V
HDMI_HPD4
R630
KRA102S
KRC103S
R626
R653
R662
19
HP DET
1K
47K
R624
1K
Q907
Q906
AVR CORE
MODEL
ISSUE
ANAM
MULTI. LAB
232
11.05.17
DESIGN
CHECK
APPROVE
S.K
W.Y.YANG
G.S.WEY
11.05.17
11.05.17
11.05.17
1
4
DRAWING NO
HDMI INPUT
HS_IN1/TRI5
VS_IN1/TRI6
HS_IN2/TRI7
VS_IN2/TRI8
MCLK
INT1
INT2
SYNC1
SYNC2
SYNC3
SYNC4
SCLK
AP0
AP1
AP2
AP3
AP4
AP5
AOUT
TRI1
TRI2
TRI3
TRI4
EP_MISO
EP_MOSI
AVLINK
EP_CS
R696
DVDDIO_3.3V
1K
C211
R693
ADV7844_RESET
P3
P4
V3
DVDDIO_3.3V
4.7K
C6
C7
EP_SCK
TTX_SCL
TTX_SDA
SCL
SDA
RESET
PWRDN1
PWRDN2
0.1uF / 16V
C252
10/16V
C177
8
7
6
64
66
63
62
61
8
7
6
60
59
3
2
57
56
55
54
53
52
51
49
48
47
46
45
44
43
42
8
7
6
5
4
2
1
40
39
38
37
36
8
7
6
5
4
2
1
35
34
7
5
50
17
18
20
23
24
25
26
27
28
29
30
HD_DB03
HD_DB09
HD_DB10
HD_DB11
HD_DG06
HD_DG07
8
7
6
GREEN_RX11
HD_DG10
HD_DG11
7
6
RED_RX03
RED_RX02
HD_DR01
RED_RX01
HD_DR00
HD_DR02
RED_RX00
33ohm (1005SIZE X 4),1/16W

RN27
HD_DR03
HD_DR05
RED_RX07
RED_RX06
HD_DR04
RED_RX05
HD_DR06
33ohm (1005SIZE X 4),1/16W

RN12
RED_RX04
HD_DR07
33ohm (1005SIZE X 4),1/16W

RN31
RED_RX10
A2
RED_RX11
B1
GND_132
GND_133
GND_134
GND_135
GND_136
GND_137
GND_138
GND_139
GND_140
GND_141
GND_142
GND_143
HD_DR08
RED_RX09
HD_DR09
V1
HD_DR10
RED_RX08
HD_DR11
CRJ10DJ330T
RN26 R705
1
2
RN22
B2
D6
J3
MCLK
R4
R672
T4
R670
ADV7844_INT
HDMI_MUTE
K4
SCLK
J4
N4
N3
M4
M3
K3
SPDIF
SDATA0
SDATA1
SDATA2
SDATA3
LRCLK
F3
HDMI 24/30/36Bit TTL Output
4
3
GREEN_RX10
HD_DG09
GREEN_RX09
HD_DG08
HDMI_RX
GREEN_RX08
33ohm (1005SIZE X 4),1/16W

RN16
GREEN:10bit
8
7
HD_DG05
GREEN_RX07
GREEN:08bit
GREEN_RX06
HD_DG04
GREEN_RX05
GREEN:12bit
HD_DG03
BLUE_RX00
BLUE_RX01
BLUE_RX02
BLUE_RX03
BLUE_RX04
BLUE_RX05
BLUE_RX06
BLUE_RX07
BLUE_RX08
BLUE_RX09
BLUE_RX10
BLUE_RX11
GREEN_RX00
GREEN_RX01
GREEN_RX02
GREEN_RX03
GREEN_RX04
GREEN_RX05
GREEN_RX06
GREEN_RX07
GREEN_RX08
GREEN_RX09
GREEN_RX10
GREEN_RX11
RED_RX00
RED_RX01
RED_RX02
RED_RX03
RED_RX04
RED_RX05
RED_RX06
RED_RX07
RED_RX08
RED_RX09
RED_RX10
RED_RX11
C1
C2
D1
D2
F2
F1
G2
G1
H2
H1
J2
J1
K2
K1
M2
M1
N2
N1
P1
P2
R1
R2
T1
T2
V2
W1
W2
Y1
Y2
AA1
AA2
AB1
AB2
AC2
AB3
AC3
GREEN_RX04
RED:12bit
8
7
6
HD_DG02
33ohm (1005SIZE X 4),1/16W

RN21
RED:10bit
4
3
GREEN_RX03
HD_DG01
GREEN_RX02
HD_DG00
GREEN_RX01
33ohm (1005SIZE X 4),1/16W

RN17
GREEN_RX00
RED:08bit
BLUE_RX11
BLUE_RX10
HD_DB08
BLUE_RX09
BLUE_RX08
BLUE:12bit
HD_DB07
BLUE:10bit
8
7
6
HD_DB06
33ohm (1005SIZE X 4),1/16W

RN30
BLUE:08bit
4
3
HD_DB05
BLUE_RX07
HD_DB04
BLUE_RX06
HD_DE
HD_HSYNC
HD_VSYNC
Sync & Control
33ohm (1005SIZE X 4),1/16W
+3.3VH2
F4
G3
In case of PCM
G4
IC905
74FCT38072DCGI
I2S0
A1
A23
B23
C12
C13
C14
C15
C16
C17
E3
E4
G7
G8
G9
G10
G13
G14
H7
H8
H9
H10
H11
H12
H13
H14
J7
J8
J9
J10
J11
J12
J13
J14
J15
J16
J17
J22
J23
K8
K9
K10
K11
K12
K13
K14
K15
K16
K17
K21
L3
L4
4.7K
R707
4.7K
R692
VGA_SCL
VGA_SDA
GND_54
GND_55
GND_56
GND_57
GND_58
GND_59
GND_60
GND_61
GND_62
GND_63
GND_64
GND_65
GND_66
GND_67
GND_68
GND_69
GND_70
GND_71
GND_72
GND_73
GND_74
GND_75
GND_76
GND_77
GND_78
GND_79
GND_80
GND_81
GND_82
GND_83
GND_84
GND_85
GND_86
GND_87
GND_88
GND_89
GND_90
GND_91
GND_92
GND_93
GND_94
GND_95
GND_96
GND_97
GND_98
GND_99
GND_100
GND_101
GND_102
GND_103
GND_104
GND_105
GND_106
GND_107
GND_108
GND_109
GND_110
GND_111
GND_112
GND_113
GND_114
GND_115
GND_116
GND_117
GND_118
GND_119
GND_120
GND_121
GND_122
GND_123
GND_124
GND_125
GND_126
GND_127
GND_128
GND_129
GND_130
GND_131
H4
H3
22
22
0.1uF / 16V
R688
R694
V-GND
G20
H20
BLUE_RX05
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
FL/FR
I2S1
AA3
AA4
AA5
AA19
AA12
AB5
AB19
AB23
AC1
AC5
AC19
AC23
SUB/CEN
RN32
MCLK
SCLK
LRCLK
SPDIF
SDATA3
L8
L9
L10
L11
L12
L13
L14
L15
L16
L17
L20
L21
L22
L23
M8
M9
M10
M11
M12
M13
M14
M15
M16
M17
M20
M21
N8
N9
N10
N11
N12
N13
N14
N15
N16
N17
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
R8
R9
R10
R11
R12
R13
R14
R15
R16
R17
T8
T9
T10
T11
T12
T13
T14
T15
T16
T17
T20
T21
T22
T23
U15
U16
U17
Y3
Y4
Y5
Y12
Y19
R682
HDMI_SCL
HDMI_SDA
V-GND
10K
10K
GND_01
GND_02
GND_03
GND_04
GND_05
GND_06
GND_07
GND_08
GND_09
GND_10
GND_11
GND_12
GND_13
GND_14
GND_15
GND_16
GND_17
GND_18
GND_19
GND_20
GND_21
GND_22
GND_23
GND_24
GND_25
GND_26
GND_27
GND_28
GND_29
GND_30
GND_3 1
GND_32
GND_33
GND_34
GND_35
GND_36
GND_37
GND_38
GND_40
GND_41
GND_42
GND_43
GND_44
GND_45
GND_46
GND_47
GND_48
GND_49
GND_50
GND_51
GND_52
R668
51
51
R690
R714
R664
58
7
8
9
11
12
13
FIELD/DE
SYNC_OUT
Y7
AC9
AA7
AB7
AC7
Y8
AA8
AB8
AC8
Y9
AA9
AB9
HD_DB02
1-TO-2 CLOCK DRIVER

R685
OUT
I2S2
SL/SR
I2S3
SDATA2
SDATA1
SDATA0
+3.3VH2
SBL/SBR
HD_VCLK1
33
IN
RN13
33ohm (1005SIZE X 4),1/16W
33
OUT
HD_VCLK2
R691
100K
T903
VS/FIELD
BLUE_RX04
HD_DB01
33ohm (1005SIZE X 4),1/16W

RN25
100K
V4
HS/CS
DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
Y15
AC15
AB15
AA15
Y16
AC16
AB16
AA16
AA11
Y13
AA13
AB13
AC13
Y14
AA14
AB14
HD_DB00
R884
0.1uF / 16V
A4
R883
24
C262
T905
LLC
BLUE_RX03
0.1uF / 16V
A5
C240
A6
24
A8
A7
V20
V21
U21
U20
T911
V-GND
T909
R698
XTALN
XTALP
BLUE_RX02
BA1
BA0
Y20
T907
R679
REFP
REFN
CS
AB10
AC10
R700
1M_NC
A9
A4
V-GND
51
51
R663
51
R667
R678
V-GND
R671
1M_NC
A5
A11
VSS
Option
AB20
AA22
V22
R22
A6
CKE
33ohm RN10
(1005SIZE X 4),1/16W
25V/0.01UF
1000P
A7
L812
C190
A8
9R005Z
0.1uF / 16V
24
CK
C180
C157
IPOD_Y/SC
A9
C168
R684
AB21
AB22
R20
R21
A11
0.1uF / 16V
0.1uF / 16V
CK
33ohm (1005SIZE X 4),1/16W
C265
24
33
R689
R704
IPOD_PR/SY
33
R711
270
24
R674
4.7K
C182 0.1uF / 16V
IPOD_PB/CVBS
VDD
A12
SPDIF_IN
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
AIN9
AIN10
AIN11
AIN12
A3
R710
R677
NC
AC20
AC21
AC22
AA23
Y22
Y23
V23
U23
U22
R23
P22
P23
A2
UDM
/CK
R702
X902
1M_NC
K22
K23
R680
A1
VSS
E2_RX+
E2_RXE2_TX+
E2_TX-
V-GND
R699
27P
51
R715
C199
M23
M22
A0
0.1uF / 16V
24
22P
28.63636MHz
C209
C210
A10/AP
SD to I/P Converter
Y10
HDMI_RX
R3
J21
T3
TEST5
TEST4
TEST3
TEST2
AC4
G12
AB4
AA21
AA20
Y21
W3
H23
H22
B16
A16
G11
TEST1
NC_10
NC_09
NC_08
NC_07
NC_06
NC_05
NC_04
NC_03
NC_02
NC_01
Y6
Y18
AA6
AA18
AB12
AB18
AC12
AC18
E1
E2
L1
L2
U1
U2
U3
U4
AB6
AC6
DVDDIO_01
DVDDIO_02
DVDDIO_03
DVDDIO_04
DVDDIO_05
DVDDIO_06
DVDDIO_07
DVDDIO_08
DVDDIO_09
DVDDIO_10
K7
L7
M7
N7
P7
R7
T7
U7
U8
U9
U10
U11
U12
U13
U14
VDD_01
VDD_02
VDD_03
VDD_04
VDD_05
VDD_06
VDD_07
VDD_08
VDD_09
VDD_10
VDD_11
VDD_12
VDD_13
VDD_14
VDD_15
A5
A11
A17
B5
B11
B17
C5
C11
C18
C19
C20
C21
C22
C23
D5
D11
D21
TVDD_01
TVDD_02
TVDD_03
TVDD_04
TVDD_05
TVDD_06
TVDD_07
TVDD_08
TVDD_09
TVDD_10
TVDD_11
TVDD_12
TVDD_13
TVDD_14
TVDD_15
TVDD_16
TVDD_17
K20
J20
PVDD_01
PVDD_02
E21
F21
G15
G16
G17
G21
H15
H16
H17
H21
N20
N21
N22
N23
P20
P21
W20
W21
W22
W23
HDMI Processor & ADC & Decoder
0.1uF / 16V
R665
BA1
W4
T902
V-GND
BA0
T919
T901
NC
UDQS
33
10K
C155
T918
C253
10uF/6.3V
51
R697
A4
B4
A3
B3
T917
0.1uF / 16V
/CS
R703
DDR_VREF
R709
C167
0.1uF / 16V
ADV7844
BLUE_RX01
BLUE_RX00
T916
CKE
VREF
C241
P0
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
P26
P27
P28
P29
P30
P31
P32
P33
P34
P35
CAS
RAS
T915
E1_RX+
E1_RXE1_TX+
E1_TX-
CK
RN29
C224
T914
V-GND
RXA_5V
RXB_5V
RXC_5V
RXD_5V
HEAC_1+
HEAC_1HEAC_2+
HEAC_2-
/CAS
DQ8
0.1uF / 16V
33ohm (1005SIZE X 4),1/16W
WE
AB11
AA10
C4
D4
C3
D3
SDRAM_A11
SDRAM_A10
SDRAM_A9
SDRAM_A8
SDRAM_A7
SDRAM_A6
SDRAM_A5
SDRAM_A4
SDRAM_A3
SDRAM_A2
SDRAM_A1
SDRAM_A0
HPA_A
HPA_B
HPA_C
HPA_D
/WE
DQ9
51
T908
T910
SDRAM_DQ15
SDRAM_DQ14
SDRAM_DQ13
SDRAM_DQ12
SDRAM_DQ11
SDRAM_DQ10
SDRAM_DQ9
SDRAM_DQ8
SDRAM_DQ7
SDRAM_DQ6
SDRAM_DQ5
SDRAM_DQ4
SDRAM_DQ3
SDRAM_DQ2
SDRAM_DQ1
SDRAM_DQ0
CEC
LDM
DQ10
UDQS
LDQS
AC11
51
T904
T906
SDRAM_CS
SDRAM_BA1
SDRAM_BA0
RXD_0+
RXD_0RXD_1+
RXD_1RXD_2+
RXD_2RXD_C+
RXD_CDDCD_SCL
DDCD_SDA
DNU
NC
DQ11
B22
A22
B10
A10
SDRAM_WE
SDRAM_CAS
SDRAM_RAS
RXC_0+
RXC_0RXC_1+
RXC_1RXC_2+
RXC_2RXC_C+
RXC_CDDCC_SCL
DDCC_SDA
NC
VDD
/RAS
33ohm (1005SIZE X 4),1/16W
HDMI_I2S
D13
D10
D8
C8
HDMI_HPD1
HDMI_HPD2
HDMI_HPD3
HDMI_HPD4
T912
CVBS_THRU
NC
DQ12
RN24
C238
CK
CK
AC17
Y11
D12
D9
C10
C9
0.1uF / 16V
R713
D7
0_NC
PWR1
PWR2
PWR3
PWR4
C226
24
UDQS
DQ13
0.1uF / 16V
CKE
AA17
AB17
0.1uF / 16V
R695
R676
CEC
SDRAM_UDQS
SDRAM_LDQS
Y17
C247
SDRAM_CK
SDRAM_CK
1M_NC
V-GND
COM_PB_THRU
VSSQ
LDQS
DQ8
DQ14
AC14
R701
B8
A8
B7
A7
B6
A6
B9
A9
D15
D14
SDRAM_VREF
R708
1M_NC
1000P
B14
A14
B13
A13
B12
A12
B15
A15
D17
D16
HDMI4_D0+
HDMI4_D0HDMI4_D1+
HDMI4_D1HDMI4_D2+
HDMI4_D2HDMI4_CK+
HDMI4_CKHDMI4_DDC_SCL
HDMI4_DDC_SDA
Option
R706
VDDQ
DQ9
VDDQ
DQ15
RN15
SDRAM_CKE
RXB_0+
RXB_0RXB_1+
RXB_1RXB_2+
RXB_2RXB_C+
RXB_CDDCB_SCL
DDCB_SDA
33ohm (1005SIZE X 4),1/16W
C166
HDMI3_D0+
HDMI3_D0HDMI3_D1+
HDMI3_D1HDMI3_D2+
HDMI3_D2HDMI3_CK+
HDMI3_DDC_SDA
RN11
HDMI2_D0+
HDMI2_D0HDMI2_D1+
HDMI2_D1HDMI2_D2+
HDMI2_D2HDMI2_CK+
HDMI2_DDC_SDA
B20
A20
B19
A19
B18
A18
B21
A21
D20
D19
RXA_0+
RXA_0RXA_1+
RXA_1RXA_2+
RXA_2RXA_C+
RXA_CDDCA_SCL
DDCA_SDA
0.1uF / 16V
DDR_VREF
HDMI_I2S
F22
F23
E22
E23
D22
D23
G22
G23
F20
E20
VDD_SDRAM_01
VDD_SDRAM_02
VDD_SDRAM_03
VDD_SDRAM_04
VDD_SDRAM_05
VDD_SDRAM_06
VDD_SDRAM_07
VDD_SDRAM_08
1K
HDMI1_D0+
HDMI1_D0HDMI1_D1+
HDMI1_D1HDMI1_D2+
HDMI1_D2HDMI1_CK+
HDMI1_DDC_SDA
RTERM
CVDD_01
CVDD_02
CVDD_03
CVDD_04
CVDD_05
CVDD_06
CVDD_07
CVDD_08
CVDD_09
CVDD_10
D18
A3
AVDD_01
AVDD_02
AVDD_03
AVDD_04
AVDD_05
AVDD_06
AVDD_07
AVDD_08
AVDD_09
AVDD_10
from : ADV3014 HDMI Out
1K
R681
A0
TVDD_3.3V
PVDD_1.8V
33ohm (1005SIZERN28
X 4),1/16W
+2.5V_DVDDIO_SDRAM
CVDD_1.8V
DVDDIO_3.3V
C186
22/6.3V
C216
0.1uF / 16V
C229
0.1uF / 16V
AVDD_1.8V
DVDD_1.8V
A2
24
NC
31
BA1
IC902
COM_PR_THRU
DQ6
DQ7
32
3
2
BA0
CVIADV7844KBCZ
R686
DQ11
DQ10
VSSQ
33
CS
R687
24
DQ5
21
4
3
2
1
33ohm (1005SIZE X 4),1/16W

90mA(20%:108mA)
R712
VDDQ VSSQ
22
8
7
5
4.7K
A1
SV_C_THRU
C263
R675
A10
SV_Y_THRU
C260
RN19
C160
22/6.3V
C235
RAS
2.5V Total : 100mA(20%: 120mA)
PVDD_1.8V
COM_Y_THRU
DQ4
14
0.1uF / 16V
0.1uF / 16V
CAS
1.8V Total : 1340mA(20%: 1608mA

0.1uF / 16V
C246
0.1uF / 16V
C191
0.1uF / 16V
C212
0.1uF / 16V
C213
0.1uF / 16V
C221
C156
0.1uF / 16V
0.1uF / 16V
C175
0.1uF / 16V
C184
0.1uF / 16V
C187
0.1uF / 16V
WE
L810
C242
DQ12
DQ3
15
RN18
3.3V Total : 450mA(20%: 540mA)
Option
VDDQ
16
11.05.17
ADV7844 Worst Measured Currents

420mA(20%:504mA)
L809
9R005Z
VSSQ
10
4
3
2
C258
33ohm (1005SIZE X 4),1/16W
+1.8VH2
DQ13
19
C266
C245
DQ7
10/16V
C222
0.1uF / 16V
0.1uF / 16V
C223
0.1uF / 16V
C234
0.1uF / 16V
C237
0.1uF / 16V
C244
0.1uF / 16V
C250
0.1uF / 16V
C257
0.1uF / 16V
C264
C158
0.1uF / 16V
0.1uF / 16V
C163
0.1uF / 16V
C171
0.1uF / 16V
C183
0.1uF / 16V
C196
0.1uF / 16V
C203
0.1uF / 16V
C204
0.1uF / 16V
C220
0.1uF / 16V
C230
C162
DQ6
9R005Z
22/6.3V
0.1uF / 16V
C173
0.1uF / 16V
C174
0.1uF / 16V
C189
0.1uF / 16V
C194
0.1uF / 16V
C202
0.1uF / 16V
C214
0.1uF / 16V
C219
0.1uF / 16V
C227
0.1uF / 16V
C233
0.1uF / 16V
C243
0.1uF / 16V
C248
0.1uF / 16V
C249
0.1uF / 16V
C256
0.1uF / 16V
22/6.3V
C185
C159
22/6.3V
C152
22/6.3V
DQ5
L816
LDQS
9R005Z
DQ2
0.1uF / 16V

260mA(20%:312mA)
+3.3VH2
DQ4
590mA(20%:708mA)
DVDD_1.8V
+1.8VH2
DQ14
TVDD_3.3V
L815
CVDD_1.8V
DQ1
VSS
DQ15
41
33ohm (1005SIZE X 4),1/16W
9R005Z
VDDQ VSSQ
65
1
2
3
C254
RN23
+1.8VH2
DQ0
DQ2
DQ3
VDD
C231
0.1uF / 16V
DQ1
C207
R666
0.1uF / 16V
33ohm (1005SIZE X 4),1/16W

DQ0
C261
10/16V
1K(1%)
C205
C197
10/16V
0.1uF / 16V
C198
0.1uF / 16V
C164
0.1uF / 16V
C178
0.1uF / 16V
C179
0.1uF / 16V
C192
0.1uF / 16V
C200
0.1uF / 16V
C217
0.1uF / 16V
C208
C161
10/16V
0.1uF / 16V
C169
0.1uF / 16V
C172
0.1uF / 16V
C181
0.1uF / 16V
C188
0.1uF / 16V
C193
0.1uF / 16V
C201
0.1uF / 16V
C218
0.1uF / 16V
C232
0.1uF / 16V
C255
0.1uF / 16V
C153
C259
22/6.3V
0.1uF / 16V
C267
0.1uF / 16V
C154
0.1uF / 16V
C165
0.1uF / 16V
C176
0.1uF / 16V
C195
0.1uF / 16V
C225
0.1uF / 16V
C236
0.1uF / 16V
C239
0.1uF / 16V
C251
0.1uF / 16V
0.1uF / 16V
R669
1K(1%)
+2.5V_DVDDIO_SDRAM
IC904
CVIA3S56D40FTPG5
+2.5VH2
L813
9R005Z
CUP12328Z
L811
+3.3VH2
L814
+1.8VH2
9R005Z
DDR_VREF
+2.5V_DVDDIO_SDRAM

250mA(20%:290mA)

100mA(20%:120mA)
+2.5V_DVDDIO_SDRAM
190mA(20%:228mA)

240mA(20%:288mA)
DVDDIO_3.3V
AVDD_1.8V
Q913
33ohm (1005SIZE X 4),1/16W
KRC103S
ON : HIGH
A7
A6
A5
A4
A3
A2
Y6
Y5
Y4
Y3
Y2
IC903
VCC OE1
A8
OE2 A1
Y7
harman/kardon
Y1
10
11
AVR 2650
Y8 GND
HDMI_AUDIO_ON
12
13
14
15
16
17
18
19
20
+3.3VH2
C206
REVISION
M/P
ANAM
MULTI. LAB
233
SCHEMATIC DIAGRAM
09.03.18
Added : 100K ohm
I2S HDMI RX to DSP
HDMI_MCLK
HDMI_SCLK
R673
HDMI_LRCK
100K
HDMI_SPDIF
HDMI_SDATA3
HDMI_SDATA2
HDMI_SDATA1
HDMI_SDATA0
100K_NC
R683
ISSUE
RN20
22X4
RN14
22X4
0.1uF
+3.3VH2
AVR CORE
MODEL
DESIGN
CHECK
APPROVE
S.K
W.Y.YANG
G.S.WEY
11.05.17
11.05.17
11.05.17
SHEET
1
4
DRAWING NO
11.05.17
HDMI RX & Decoder

9.8mA(Max:10.5mA)
T920
WP_1
T921
Added:2009.01.04
AF14
AD12
AC12
AD14
AE13
AE14
FS_SEL
HDMI_AUDIO_ON
V_CLK_SEL
BUSY_CHECK
T922
C272
0.1uF / 16V
ADV3014_INT_TX
/RESET
V26
V25
HVIKIC7SZ08FU
0.1uF / 16V
R754
10K(1%)
C348
C385
22/6.3V
C346
0.1uF / 16V
25V/0.01UF
0.1uF / 16V
C298
C270
C329
0.1uF / 16V
0.1uF / 16V
C336
0.1uF / 16V
C343
0.1uF / 16V
AD3
AD4
AD5
AD6
AD7
1
2
3
5
6
7
8
1
2
3
4
5
6
7
8
53
FSDQSU2
50
52
51
33
FSDQMU2
49
FSVREF
R743
21
22
23
/RAS
24
/CS
25
NC
42
FDADDR12
26
BA0
A11
41
FDADDR11
27
BA1
A9
40
FDADDR9
28
A10/AP
A8
39
FDADDR8
29
A0
A7
38
FDADDR7
30
A1
A6
37
FDADDR6
A2
A5
36
FDADDR5
32
A3
A4
35
FDADDR4
VDD
VSS
34
FSCLK-
/WE
/CAS
NC
A12
FSCLK+
280(1%)
44
FSCKE
43
CK
CKE
45
46
/CK
FDADDR8
FSCKE
C318
0.1uF / 16V
+2.5V_DDR
IC908
8
7
60
UDQS
1
2
3
4
8
6
7
8
4
52
48
47
49
42
41
40
2010.09.27
FDADDR9
A10/AP
A8
39
C365
FDADDR11
A9
FDADDR8
A0
A7
38
FDADDR3
A11
BA1
FDADDR7
A1
A6
37
FDADDR2
FDADDR12
BA0
FDADDR6
A2
A5
36
FDADDR1
NC
FDADDR5
A3
A4
35
FDADDR11
FDADDR0
/CS
FDADDR4
VDD
VSS
NC
A12
45
FSCLK+
280(1%)
FSCKE
44
CK
CKE
43
/CK
46
21
22
23
FDADDR3
FDADDR10
/RAS
24
FDADDR10
FSDQSU0
FSDQMU0
FSCLK-
/WE
/CAS
25
FDADDR2
FSBKSEL1
0ohm (1005SIZE X 4),1/16W
33
FSVREF
26
FSBKSEL0
FSDATAU7
R748
27
NC
28
/FSCS0
FDADDR1
FSADDRU11
UDM
29
FDADDR0
1
2
3
FSADDRU3
VSS
LDM
30
/FSRAS
0ohm (1005SIZE X 4),1/16W

RN50
FSADDRU10
VREF
DNU
31
FSBKSEL1
33ohm (1005SIZE X 4),1/16W
FSADDRU2
VDD
32
1
2
3
4
FSADDRU1
RN33
33
FSADDRU0
/FSCAS
FSBKSELU1
FSBKSEL0
FSBKSELU0
SC_VSYNC
RN36
SC_VCLK
SC_HSYNC
0.1uF / 16V
34
/FSWE
FSDATAU6
50
17
0.1uF / 16V
NC
18
C364
33
SC_DB05
FSDATAU5
33ohm (1005SIZE X 4),1/16W
NC
19
RN55
SC_DB04
59
58
57
56
55
VSSQ
LDQS
54
VDDQ
20
NC
C284
FSDATAU4
53
13
DQ8
DQ7
14
VDDQ
15
DQ9
FSDATAU3
RN38
51
8
7
1
2
FSDQMU1
SC_DB03
RN54
RN42
DQ10
16
4
3
2
TTL OUTPUT
C363
0.1uF / 16V
FSDQSU1
63
62
8
7
6
5
61
4
2
1
6
8
7
6
5
8
7
6
5
8
SC_DB02
RN51
DQ11
0.1uF / 16V
12
VSSQ
C342
0.1uF / 16V
FSDATAU8
FSDATAU2
33ohm (1005SIZE X 4),1/16W
10
11
DQ6
DQ12
FSDATAU1
DQ5
VDDQ
C276
VDDQ VSSQ
DQ13
FSDATAU0
DQ4
DQ14
DQ3
RN56
RN60
5
VSSQ
5
8
7
FSDATAU12
VSS
DQ15
DQ2
C335
0.1uF / 16V
FSDATAU13
66
DQ1
FSDATAU14
65
VDDQ VSSQ
FSDATAU15
64
1
2
DQ0
VDD
0.1uF / 16V
1
4
3
2
1
4
3
2
RN57
31
FDADDR7
C312
5
6
NC

250mA(20%:290mA)
FDADDR6
UDQS
0.1uF / 16V
10/16V
2
3
4
1
2
3
4
VSSQ
33
FDADDR5
FDADDR3
FSDATAU9
SC_DR08
66
63
62
61
60
59
58
57
48
UDM
FSDATAU23
47
56
55
VSS
LDM
NC
54
13
14
15
16
17
18
19
DNU
20
4
3
FDADDR12
FSADDRU12
FDADDR2
C314
7
6
5
65
10
11
12
8
7
6
5
8
7
3
4
5
6
7
8
5
6
FDADDR9
1
8
4
3
2
1
4
3
2
1
4
3
2
64
1
2
3
4
5
6
7
8
9
6
5
4
3
2
1
4
3
2
1
2
1
1
2
1
2
3
4
D26
RPLL_33
A14
C25
RPLL_1.8
ADC1.8-0
ADC1.8-1
ADC1.8-2
AB4
AC4
AC5
E26
H26
J26
M26
H24
D4
D6
D7
D8
D10
D11
D12
D13
D14
D15
D17
D18
D20
D22
D23
C9
C19
FSVREF-0
FSVREF-1
LBADC3.3
AC9
AC22
AB23
Y23
V23
T23
P23
M23
IO3.3-10
IO3.3-11
IO3.3-12
IO3.3-13
IO3.3-14
IO3.3-15
IO3.3-16
IO3.3-0
IO3.3-1
IO3.3-2
IO3.3-3
IO3.3-4
IO3.3-5
IO3.3-6
IO3.3-7
IO3.3-8
IO3.3-9
ADC_3.3
ADCA_3.3
ADCB_3.3
ADCC_3.3
ADCSC_3.3
PPWR
PBIAS
0.1uF / 16V
OCM_ RE
OCM_ WE
ROM_ CS
RN48
SC_DB00
SC_DG01
SC_DR00
RN49
33ohm (1005SIZE33 4),1/16W
X
SC_DR01
FLASH_MEMORY
U25
U26
L818
#FLASH MEMORY
+3.3VH1
9R005Z
IC907
CVIMX29LV320DTTI-70G
1
2
A16
A15
A14 BYTE#
10K_NC
OCMADDR17
R729
OCMADDR11
HEATSINK_HOLE
OCMADDR10
OCMADDR9
A8
A19
DQ5
A20
DQ12
WE#
DQ4
OCMDATA15
OCMDATA7
44
OCMADDR12
45
A9
10K
OCMADDR13
M/P
46
43
42
3
4
5
DQ13
DQ6
DQ14
A10
DQ7
2007.10.06
Connect pin3 to CHGND
Vss
DQ15
/A-1
A11
10K
R719
A12
10
R716
A13
11
OCMADDR14
ADV3014_INT
OCMDATA14
OCMDATA6
OCMDATA13
ISSUE
OCMDATA5
ANAM
MULTI. LAB
H2
OCMADDR20
2.7K
2.7K
R868
VREF
0.1uF / 16V
CVIA3S56D40FTPG5
OCMDATA12
13
NC
14
WP#/ACC
15
RY/BY#
DQ11
OCMDATA11
36
10K
C310
10K
R722
Vcc
OCMDATA3
35
R726
RESET#
10K
47K
R739
OCMDATA10
OCMADDR3
OCMADDR2
33
32
A6
DQ8
A5
DQ0
A4
OE#
28
A3
Vss
31
DQ1
30
OCMDATA8
A0
AVR CORE
29
OCM_ RE
R745
A1
SHEET
OCMDATA0
R733
CE#
SCHEMATIC DIAGRAM
OCMDATA1
27
16
A7
A2
ROM_ CS
MODEL
26
OCMADDR4
18
OCMADDR5
2
3
OCMDATA9
19
OCMADDR6
DQ9
20
OCMADDR7
A17
OCMDATA2
21
harman/kardon
DQ2
22
OCMADDR8
A18
23
OCMADDR18
10K
24
R742
17
DQ10
OCMADDR19
REVISION
DQ3
34
37
12
0.1uF / 16V
/RESET
AVR 2650
11.05.17
OCMDATA4
R723
0.1uF
R831
FDADDR4
FSADDRU9
FSADDRU5
FDADDR1
FSDATAU10
SC_DR09
OCMADDR21
C550
0ohm (1005SIZE X 4),1/16W

RN41
FSADDRU4
FSDATAU11
SC_DR07
33ohm (1005SIZE X 4),1/16W

RN58
OCM_ WE
VDD
FSDATAU22
33ohm (1005SIZE X 4),1/16W
10K
H1
R869
SDA
FDADDR0
33ohm (1005SIZE X 4),1/16W
SC_DR06
OCMADDR15
0.1uF / 16V
C373
SCL
FDADDR10
SC_DR03
33ohm (1005SIZE X 4),1/16W

RN34
AC20
T24
T25
T26
R23
R24
R25
A2
GND
NC
FSDATAU21
1
2
WP
2.2K
R870
A1
VCC
FSBKSEL1
Change Value : 33ohm-->0ohm
ADV3014_INT2
A0
/FSWE
FSBKSEL0
SC_DR05
+3.3VH1
CVIAT24C64CNSHT
/FSRAS
SC_DR02
R751
IC931
LDQS
C274
FSDATAU20
C326
SC_DG07
33ohm (1005SIZE X 4),1/16W

RN39
OCMADDR16
*EEPROM
/FSCAS
SC_DG08
OCMDATA15
OCMDATA14
OCMDATA13
OCMDATA12
OCMDATA11
OCMDATA10
OCMDATA9
OCMDATA8
OCMDATA7
OCMDATA6
OCMDATA5
OCMDATA4
OCMDATA3
OCMDATA2
OCMDATA1
OCMDATA0
AC25
AC26
AD24
AD25
AD26
AC24
VDDQ
RN45
33ohm (1005SIZE X 4),1/16W
SC_DG09
AE21
AD21
AC21
AF22
AE22
AD22
AF23
AE23
AD23
AC23
AF24
AF25
AF26
AE24
AE25
AE26
DQ8
NC
0ohm (1005SIZE X 4),1/16W
SC_DG06
OCMADDR21
OCMADDR20
OCMADDR19
OCMADDR18
OCMADDR17
OCMADDR16
OCMADDR15
OCMADDR14
OCMADDR13
OCMADDR12
OCMADDR11
OCMADDR10
OCMADDR9
OCMADDR8
OCMADDR7
OCMADDR6
OCMADDR5
OCMADDR4
OCMADDR3
OCMADDR2
OCMADDR1
VDDQ
FSDATAU19
RN35
SC_DG03
33ohm (1005SIZE X 4),1/16W

RN46
AF15
AE15
AD15
AC15
AF16
AE16
AD16
AF17
AE17
AD17
AC17
AF18
AE18
AD18
AF19
AE19
AD19
AC19
AF20
AE20
AD20
AF21
DVDDIO_3V3_3014
Option
/FSRAS
/FSWEU
0.1uF / 16V
SC_DG00
/JTAG_BS_E
JTAG_BS_TMS
JTAG_BS_TDO
GPIO44
JTAG_BS_TDI
JTAG_BS_RST
JTAG_BS_TCK
L10
M10
N10
P10
R10
T10
M11
N11
P11
R11
K12
L12
M12
N12
P12
R12
T12
U12
K13
L13
M13
N13
P13
R13
T13
U13
K14
L14
M14
N14
P14
R14
T14
U14
K15
L15
M15
N15
P15
R15
T15
U15
M16
N16
P16
R16
L17
M17
N17
P17
R17
AA2
AA3
AA4
IC910
/FSCAS
/FSRASU
FSCKEU
SC_DG04
P24
P25
R26
P26
DQ9
FSDATAU18
33ohm (1005SIZE X 4),1/16W
SC_DB01
OCM_TIMER1
/OCM_INT2
/OCM_INT1
/FSCS0
/FSCASU
SC_DG05
N23
N24
N25
N26
DQ11
DQ10
DQ7
SC_DG02
+3.3VH1
VCO_LV
OBUFC_CLK
SCAN_EN
SLAVE_SCL
SLAVE_SDA
/FSWE
FSADDRU8
SC_DB08
33ohm (1005SIZE X 4),1/16W

RN53
1
4
10K
CUP12328Z
234
25
1
2
3
ADV7511_INT
ADV7844_INT
M24
D25
A1
W24
Y24
W23
CJP05GA19ZY
CN62
T923
/OCM_RE
/OCM_WE
/ROM_CS
/OCM_CS0
/OCM_CS1
/OCM_CS2
AVS_IN_SCL
AVS_IN_WORD_SEL
AVS_IN_DATA
AVS_OUT_DATA
AVS_OUT_SCL
AVS_OUT_WORLD_SEL
0.1uF / 16V
33
/FSCS0U
48
+5VA
MSTR0_SCL
MSTR0_SDA
MSTR1_SCL
MSTR1_SDA
MSTR2_SCL
MSTR2_SDA
VGA0_SCL
VGA0_SDA
VGA1_SCL
VGA1_SDA
C307
DDR
41
GPROBE_UPGRADE
/RESET
C306
33
0.1uF / 16V
RN52
0.1uF / 16V
WP_2
RN61
0ohm (1005SIZE X 4),1/16W

RN40
SC_DE
OCMDATA15
OCMDATA14
OCMDATA13
OCMDATA12
OCMDATA11
OCMDATA10
OCMDATA9
OCMDATA8
OCMDATA7
OCMDATA6
OCMDATA5
OCMDATA4
OCMDATA3
OCMDATA2
OCMDATA1
OCMDATA0
VSSQ
FSDQSU3
FSADDRU7
SC_DB09
C361
HDMI_MUTE
LBADC_IN6
LBADC_IN5
LBADC_IN4
LBADC_IN3
LBADC_IN2
LBADC_IN1
LBADC_RETURN
OCM_UDO_0
OCM_UDI_0
OCM_UDO_1
OCM_UDI_1
DQ6
RN37
10/16V
C305
SW_P+5V
FSDATAU24
DQ12
FSDATAU17
AA24
AA23
A3
A2
AB26
AB25
AA26
AA25
Y26
Y25
IR0
DQ5
VDDQ
C268
22
PWM0
PWM1
PWM2
VDDQ VSSQ
C300
0.1uF / 16V
FSDATAU25
DQ13
FSDATAU16
/RESET
HDMI_SCL
HDMI_SDA
XTAL
TCLK
DQ4
FSDATAU26
DQ14
AD9
DIP_BODD
BVS
BHS
BHREF_DE
DQ3
FSDATAU27
FSADDRU6
SC_DB06
SC_DR04
OCMADDR21
OCMADDR20
OCMADDR19
OCMADDR18
OCMADDR17
OCMADDR16
OCMADDR15
OCMADDR14
OCMADDR13
OCMADDR12
OCMADDR11
OCMADDR10
OCMADDR9
OCMADDR8
OCMADDR7
OCMADDR6
OCMADDR5
OCMADDR4
OCMADDR3
OCMADDR2
OCMADDR1
OCMADDR0
VSSQ
RN59
R728
DCLK
DHS
DVS
DEN
DQ2
VSS
DQ15
47
UART_TX
UART_RX
EBLU0
EBLU1
EBLU2
EBLU3
DQ1
33ohm (1005SIZE X 4),1/16W
3
2
10K
GPROBE_TXD
GPROBE_RXD
4.7K
4.7K
R864
AE11
AF11
AC10
AD10
AE10
AF10
AD11
W26
W25
B2
B3
5
R730
R734
AB24
FLI30336AC
BDATA0
BDATA1
BDATA2
BDATA3
BDATA4
BDATA5
BDATA6
BDATA7
BDATA8
BDATA9
BDATA10
BDATA11
BDATA12
BDATA13
BDATA14
BDATA15
BDATA16
BDATA17
BDATA18
BDATA19
BDATA20
BDATA21
BDATA22
BDATA23
VDDQ VSSQ
RN43
40
8
6
10K
V24
U23
U24
ADV7844_RESET
ADV3014_RESET
PWR1
FSDATAU28
39
47P
RN47
+3.3VH1 +3.3VH1 +3.3VH1
B26
C26
+3.3V_PLL
IC906
DQ0
C295
0.1uF / 16V
FSDATAU29
38
47P
C286
19.660M
+3.3V_PLL
10K
X903
R768
N4
L2
L3
K1
HD_VSYNC
HD_HSYNC
HD_DE
DIP_RAW_HS_CS
DIP_EXT_CLAMP
DIP_EXT_COAST
DIP_CLEAN_HS_OUT
VDD
0.1uF / 16V
FSDATAU30
SC_DB07
C291
22
C294
33ohm (1005SIZE X 4),1/16W
FSDATAU31
33ohm (1005SIZE X 4),1/16W

L24
L23
L26
L25
K24
K23
K26
K25
J24
J23
G24
G23
G26
G25
F24
F23
F26
F25
E24
E23
8BIT RGB INPUT
R760
IPCLK0
IPCLK1
IPCLK2
IPCLK3
/FSWEU
/FSCASU
/FSRASU
FSCKEU
FSBKSELU0
FSBKSELU1
R766
75_NC
100P_NC
C389
10K_NC
R759
B1
C3
C2
C1
D3
D2
D1
E3
E2
E1
F3
F2
F1
G3
G2
G1
H3
H2
H1
J3
J2
J1
K3
K2
HD_DB04
HD_DB05
HD_DB06
HD_DB07
HD_DB08
HD_DB09
HD_DB10
HD_DB11
HD_DG04
HD_DG05
HD_DG06
HD_DG07
HD_DG08
HD_DG09
HD_DG10
HD_DG11
HD_DR04
HD_DR05
HD_DR06
HD_DR07
HD_DR08
HD_DR09
HD_DR10
HD_DR11
+3.3VH1
*GPROBE
N2
M2
M3
M1
10K
CK3E-/EBLU5
CK3E+/EBLU4
CKE-/EBLU7
CKE+/EBLU6
CH2E-/EGRN1
CH2E+/EGRN0
CH1E-/EGRN3
CH1E+/EGRN2
CH0E-/EGRN5
CH0E+/EGRN4
CH3O-/EGRN7
CH3O+/EGRN6
CKO-/ERED1
CKO+/ERED0
CH2O-/ERED3
CH2O+/ERED2
CH1O-/ERED5
CH1O+/ERED4
CH0O-/ERED7
CH0O+/ERED6
DIP_AODD
AVS
AHS
AHRFE_DE
C23
D24
C24
C4
C21
C20
R717
FSWE
FSCAS
FSRAS
FSCKE
FSBKSEL0
FSBKSEL1
KRC103S
FSCLK+
FSCLK/FSCS0U
FSDQSU0
FSDQSU1
FSDQSU2
FSDQSU3
FSDQMU0
FSDQMU1
FSDQMU2
FSDQMU3
R757
Q915
4.7K
R756
4.7K
R737
4.7K
Q914
KRC103S
N3
Y1
Y2
Y3
N1
P4
M4
L1
HD_VCLK1
BYPASS_OFF
4.7K
R731
10K
10K
10K
10K
D5
C5
D21
C22
B6
B11
A17
A22
A6
A11
B17
B22
R720
R749
R718
R762
+3.3VH1
ADATA16
ADATA17
ADATA18
ADATA19
ADATA20
ADATA21
ADATA22
ADATA23
TORINO<-->DDR
/FSCS0
+3.3VH1
FSCLKP
FSCLKN
FSCS0
FSCS1
FSDQS0
FSDQS1
FSDQS2
FSDQS3
FSDQM0
FSDQM1
FSDQM2
FSDQM3
ADATA8
ADATA9
ADATA10
ADATA11
ADATA12
ADATA13
ADATA14
ADATA15
FSADDRU0
FSADDRU1
FSADDRU2
FSADDRU3
FSADDRU4
FSADDRU5
FSADDRU6
FSADDRU7
FSADDRU8
FSADDRU9
FSADDRU10
FSADDRU11
FSADDRU12
V3
V2
V1
W4
W3
W2
W1
Y4
ADATA0
ADATA1
ADATA2
ADATA3
ADATA4
ADATA5
ADATA6
ADATA7
C18
C17
C16
C15
C13
C10
C8
C7
C6
C12
D16
C14
C11
T3
T2
T1
U4
U3
U2
U1
V4
FSADDR0
FSADDR1
FSADDR2
FSADDR3
FSADDR4
FSADDR5
FSADDR6
FSADDR7
FSADDR8
FSADDR9
FSADDR10
FSADDR11
FSADDR12
EXT_OSD_VS
EXT_OSD_HS
EXT_OSD_CLK
+2.5V_DDR
10K(1%)
FSDQMU3
HD_DB02
HD_DB03
HD_DG02
HD_DG03
HD_DR02
HD_DR03
ADC_+TEST
VOUT2
FSDATAU0
FSDATAU1
FSDATAU2
FSDATAU3
FSDATAU4
FSDATAU5
FSDATAU6
FSDATAU7
FSDATAU8
FSDATAU9
FSDATAU10
FSDATAU11
FSDATAU12
FSDATAU13
FSDATAU14
FSDATAU15
FSDATAU16
FSDATAU17
FSDATAU18
FSDATAU19
FSDATAU20
FSDATAU21
FSDATAU22
FSDATAU23
FSDATAU24
FSDATAU25
FSDATAU26
FSDATAU27
FSDATAU28
FSDATAU29
FSDATAU30
FSDATAU31
P3
P2
P1
R4
R3
R2
R1
T4
R750
FSVREF

250mA(20%:290mA)
+2.5V_DDR
B4
A4
B5
A5
B7
A7
B8
A8
B9
A9
B10
A10
B12
A12
B13
A13
B15
A15
B16
A16
B18
A18
B19
A19
B20
A20
B21
A21
B23
A23
B24
A24
3
4
AD13
AC13
AF13
+3.3V_ADCSC
L830
9R005Z
ADC2
27mA(Max:38mA)
10K
R767
+3.3VH1
IC909
AIP_RAW_HS_CS
AIP_RAW_VS
FSVREFVSS1
FSVREFVSS2
AF12
AE12
5
6
7
8
RGB 10BIT INPUT
10K
R763
+3.3V_ADCC
L831
9R005Z
D19
D9
10K
RPLL_AGND
RPLL_AGND-1
RPLL_DGND
AA1
AC7
RN44
A25
A26
B25
0_NC
SV1P
SV2P
SV3P
SV4P
SVN
VSSA18_DLL
R882
16V
16V
16V
16V
16V
B14
AB2
AE1
AE4
AE7
AF9
/
/
/
/
/
VDDA18_DLL
C273
C368
C347
C360
C374
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
LVDS3.3-0
LVDS3.3-1
LVDS3.3-2
LVDS3.3-3
56
22
22
22
56
LBADC_GND
0_NC
AC11
R881
C1P
C2P
C3P
C4P
CN
AGND-0
AGND-1
AGND-2
AGND-3
AGND-4
AGND-5
AGND-6
AGND-7
AGND-8
AC1
AF2
AF5
AF8
AF6
AB3
AC3
AD2
AE3
AC6
AE6
AC8
AD8
AE9
0.1uF / 16V
0.1uF / 16V
0.1uF / 16V
0.1uF / 16V
0.1uF / 16V
LVDS_PLL_3.3
C377
C319
C311
C350
C327
+3.3V_PLL
CVIA3S56D40FTPG5
FSDATA0
FSDATA1
FSDATA2
FSDATA3
FSDATA4
FSDATA5
FSDATA6
FSDATA7
FSDATA8
FSDATA9
FSDATA10
FSDATA11
FSDATA12
FSDATA13
FSDATA14
FSDATA15
FSDATA16
FSDATA17
FSDATA18
FSDATA19
FSDATA20
FSDATA21
FSDATA22
FSDATA23
FSDATA24
FSDATA25
FSDATA26
FSDATA27
FSDATA28
FSDATA29
FSDATA30
FSDATA31
B1P
B2P
B3P
B4P
BN
LVDS_GND-1
LVDS_GND-2
LVDS_GND-3
LVDS_GND-4
LVDS_PLL_GND
56
22
22
22
56
A1P
A2P
A3P
A4P
AN
E25
H25
J25
M25
H23
AC2
AE2
AE5
AE8
AF3
DDR2.5-0
DDR2.5-1
DDR2.5-2
DDR2.5-3
DDR2.5-4
DDR2.5-5
DDR2.5-6
DDR2.5-7
DDR2.5-8
DDR2.5-9
DDR2.5-10
DDR2.5-11
DDR2.5-12
DDR2.5-13
DDR2.5-14
16V
16V
16V
16V
16V
/
/
/
/
/
E4
F4
G4
H4
J4
K4
L4
AC14
AC16
AC18
K10
U10
K11
L11
T11
U11
K16
L16
T16
U16
K17
T17
U17
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
AB1
AF1
AF4
AF7
AD1
DGND-3
DGND-4
DGND-5
DGND-6
DGND-7
DGND-8
DGND-9
DGND-10
DGND-11
DGND-12
DGND-13
DGND-14
DGND-15
DGND-16
DGND-17
DGND-18
DGND-19
DGND-20
DGND-21
DGND-22
DGND-23
DGND-24
DGND-200
DGND-26
DGND-27
DGND-28
DGND-29
DGND-30
DGND-31
DGND-32
DGND-33
DGND-34
DGND-35
DGND-36
DGND-37
DGND-38
DGND-39
DGND-40
DGND-41
DGND-42
DGND-43
DGND-44
DGND-45
DGND-46
DGND-47
DGND-48
DGND-49
DGND-50
DGND-51
DGND-52
DGND-53
DGND-ADC0
DGND-ADC1
DGND-ADC2
C293
C313
C279
C321
C292
R765
R738
R752
R758
R761
0_NC
CVBS_THRU
56
56
22
22
56
R753
R735
R740
R755
R746
R880
COM_PR_THRU
0.1uF / 16V
0.1uF / 16V
0.1uF / 16V
0.1uF / 16V
0.1uF / 16V
22
22
22
22
56
R721
R736
R724
R744
R732
0_NC
COM_Y_THRU
C299
C341
C278
C282
C281
R741
R747
R764
R727
R725
R879
COM_PB_THRU
CORE1.8-0
CORE1.8-1
CORE1.8-2
CORE1.8-3
CORE1.8-4
CORE1.8-5
CORE1.8-6
CORE1.8-7
CORE1.8-8
CORE1.8-9
CORE1.8-10
CORE1.8-11
CORE1.8-12
3.3V Total : 166.3mA(2Max: 202.1mA)
BYPASS_ON
+3.3VH1
+3.3V_ADCB
L833
9R005Z
ADC1
25mA(Max:34mA)
2.5V Total : 385mA(Max: 412mA)
+3.3VH1
+3.3V_ADCA +3.3VH1
L823
9R005Z
10/16V
1.8V Total : 1923mA(Max: 2012mA)

D
+3.3VH1
C351
+1.8V_CORE
+3.3V_ADC
L828
9R005Z
0.1uF / 16V
+3.3VH1
11.05.17
10/16V
C315
+3.3V_ADC
+3.3V_ADCA
+3.3V_ADCB
+3.3V_ADCC
+3.3V_ADCSC
+3.3V_PLL
+1.8V_PLL
+1.8V_DLL
+1.8V_ADC
+3.3V_LVDS
+3.3V_LVDS_PLL
+2.5V_DDR

25mA(Max:26mA)
C322
C356
0.1uF / 16V
C283
0.1uF / 16V
C288
C280
C392
0.1uF / 16V
C386
0.1uF / 16V
C380
0.1uF / 16V

15mA(Max:16mA)
L832
9R005Z
ADC2
C376
FLI30336 Worst Measured Currents
+3.3V_LBADC
FSVREF
+3.3V_IO
+3.3VH1
+1.8V_PLL
L829
9R005Z

0.5mA(Max0.6mA)
ADC1
+1.8VH1
+1.8V_DLL
L817
9R005Z
C383
+1.8VH1
+1.8V_ADC
10/16V
C301

43mA(Max:45mA)
L819
0.1uF / 16V
+1.8VH1
0.1uF / 16V
+3.3V_LVDS
9R005Z
C287
0.1uF / 16V
C362
10/16V
C369
0.1uF / 16V
C355
0.1uF / 16V
C379
0.1uF / 16V
0.1uF / 16V
C393
C352
C391
25V/0.01UF
C390
0.1uF / 16V
C340
25V/0.01UF
C357
0.1uF / 16V
C337
25V/0.01UF
C316
0.1uF / 16V
C308
0.1uF / 16V
C302
0.1uF / 16V
C297
0.1uF / 16V
C330
25V/0.01UF
C296
0.1uF / 16V

69mA(Max:83mA)
L820
9R005Z
0.1uF / 16V
+3.3VH1
22/6.3V
C275
+3.3V_LVDS_PLL
L825
9R005Z
0.1uF / 16V
+3.3VH1
10/16V
C370
+2.5V_DDR

11mA(Max:12mA)
FSVREF
FSVREF

385mA(Max:412mA)
L827
+2.5VH1
C323
C334
C394
0.1uF / 16V
0.1uF / 16V
C384
C388
0.1uF / 16V
C382
0.1uF / 16V
C378
0.1uF / 16V
C372
0.1uF / 16V
C367
0.1uF / 16V
C359
0.1uF / 16V
C354
0.1uF / 16V
C345
0.1uF / 16V
C339
0.1uF / 16V
C332
0.1uF / 16V
C325
0.1uF / 16V
C290
0.1uF / 16V
C285
0.1uF / 16V
C277
0.1uF / 16V
0.1uF / 16V
C333
C387
0.1uF / 16V
C381
0.1uF / 16V
C371
0.1uF / 16V
C366
0.1uF / 16V
C358
0.1uF / 16V
C353
0.1uF / 16V
C344
0.1uF / 16V
C338
0.1uF / 16V
C331
0.1uF / 16V
C324
0.1uF / 16V
C317
0.1uF / 16V
C309
0.1uF / 16V
0.1uF / 16V
C320
C303
22/6.3V
C328
22/6.3V
+3.3V_LBADC
L821
9R005Z
25V/0.01UF
+3.3VH1
+3.3V_IO
10/16V
C289

24mA(Max:24mA)
L826
9R005Z
0.1uF / 16V
+3.3VH1
C349
+1.8V_CORE
L824
10/16V
C375

1850mA(Max:1925mA)
10/16V
C269
L822
10/16V
C271
+1.8VH1
0.1uF / 16V
OCMADDR1
DESIGN
CHECK
APPROVE
S.K
W.Y.YANG
G.S.WEY
11.05.17
11.05.17
11.05.17
DRAWING NO
SCALER
CUP12328Z
L835
0.1uF
Option
1000P_NC
C543
1000P_NC
2A2
2A3
2Y3
17
GND
GND
18
2A4
2Y4
19
2A5
2Y5
20
2A6
2Y6
21
Vcc
Vcc
22
2A7
2Y7
2A8
2Y8
24
GND
25
TX_DR11
TX_DR10
TX_DR09
TX_DR08
TX_DR07
TX_DR06
TX_DR05
TX_DR04
TX_DR03
TX_DR02
TX_DG11
TX_DR00
TX_DR01
D901
BAR43C_NC
49.9
49.9
R795
C426
C442
0.1uF / 16V
C427
C454
0.1uF / 16V
AVDD
34
12
13
14
15
16
17
18
19
20
21
22
23
26
PVDD
C467
0.1uF / 16V
0.1uF / 16V
C455
12
13
14
10K
R792
15
27
GND
24
C468
BGVDD
0.1uF / 16V
25
C555
+5VH1
R836
Q916
UPA672T
0.1uF / 16V
25V/0.01UF
0_NC
C480
C445
R863
33
R862
33
8
7
22/6.3V
R780
R774
4.7K
Option
TX_DB08
1.8K
TX_DB09
+3.3VH2
+8VA
TX_DG01
ARC_SPDIF_OUT
IC917
R793
NJU7754
TX_DG02
TX_DG03
RN81
Vin
Cont
0.1uF
Vout
NC
0.1uF
C433
R775
22_NC
0_NC
TX_DB11
R816
R801
0_NC
6
5
TX_DB10
TX_DG00
3
2
2Y9
+5VH1
TC7SH125FU_NC
DSP_LRCK/DR2
TX_DB07
2Y8
GND
IC921
C410
TX_DB06
33ohm RN80
(1005SIZE X 4),1/16W
4
0.1uF / 16V_NC
TX_DB04
C396
C446
0.1uF / 16V
TX_DB03
0.1uF / 16V
23
R794
C424
28
HPD/HEAC-
TX_DG03
RN91
+5V
TX_DB05
C406
GND
+5VH1
4.7K
+1.8VH2
DSP_SCLK/CLK
22
2Y7
DDC DATA
9R005Z
21
Vcc
2Y6
TX_DB02
3
2
1
19
2Y5
18
2Y4
L837
33ohm RN79
(1005SIZE X 4),1/16W
20
2Y3
GND
TX_DB00
4
2
1
16
15
2Y2
8
13
14
2Y1
DDC CLOCK
R822
1.8K
TX_DB01
33ohm RN78
(1005SIZE X 4),1/16W
12
1Y9
17
1Y8
1Y10
R861
GND
1Y7
UTILITY/HEAC+
25V/0.01UF
TX_DE
0.1uF / 16V
CKCE REMOTE
16
11
CK+
CK SHIELD
17
10
D0 SHIELD
D0-
18
D1D0+
19
1K
R779
8.2K
R797
0
R796
0.1uF / 16V
PVDD
C425
C413
0.1uF / 16V
C409
GND
99
GND
28
PLVDD
R_EXT
GND
HSYNC
DVDD
98
GND
29
LRCLK
AVDD
SCLK
DE
I2S3
97
I2S2
30
I2S1
HPD
I2S0
D0
MCLK
96
SPDIF I/O
31
DSD_CLK
GND
DSD5
D1
DSD4
95
0.1uF / 16V
32
DSD3
TXC-
DSD2
D2
C436
33
DSD1
TXC+
DSD0
D3
JK97
35
D4
36
TX0-
37
D5
38
GND
TX0+
D2-
D1 SHIELD
39
PD/AD
D2 SHIELD
D6
ADV7511
D2+
D1+
D7
C438
0.1uF / 16V
10
D8
HDMI OUTPUT1
ADV7511_INT
40
TX1-
0.1uF / 16V
R804
22
11
D9
TX_HSYNC
HEAC-
HEAC+
TX1+
IC918
33
R860
2 OE1
DDCSCL
D10
33
R859
2 OE2
100
41
DSP_S0/DR0
2Y10
R834
100
42
AVDD
DSP_MCLK
2A10
SCL
TX2-
D11
+1.8VH2
43
D12
0_NC
9R005Z
44
33
2A9
SDA
GND
R776
45
TX2+
0.1uF / 16V
R798
C423
46
D13
C479
47
INT
D14
DSP_SPDIF
GND
D35
D34
D33
D32
D31
D30
D29
D28
D27
D26
D25
D24
D23
D22
D21
D18
D19
D20
GND
DVDD33
SPDIF OUT
D15
VSYNC
6
5
8
7
6
5
8
7
4
2
1
1
4
6
2A8
2A7
1Y6
10
Vcc
1Y5
11
2A6
48
D16
TX_VSYNC
24
SC_DG01
2A5
49
94
GND
L843
10K
50
93
TX_VCLK
25
2
1
2 OE1
TX_DG02
2A4
Vcc
26
2 OE2
2Y10
GND
51
CEC_CLK
CEC_IN
33ohm (1005SIZE X 4),1/16W
27
25
2Y9
2A10
SC_DG00
2A3
52
9R005Z
28
24
TX_DG01
GND
2A9
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
2Y8
GND
23
2A8
26
34
TX_DG00
2A2
39
C430
0.1uF / 16V
2A1
38
SC_DB09
1A10
37
TX_DB11
SC_DB08
1A9
36
TX_DB10
SC_DB07
1A8
35
SC_DB06
GND
34
SC_DB05
1A7
33
SC_DB04
1A6
32
SC_DB03
1A5
31
SC_DB02
33ohm (1005SIZERN90
X 4),1/16W
2Y7
27
HD_DG03
SC_DB01
8
7
TX_DB09
33
C452
SC_DB00
Vcc
53
RN77
C398
54
DVDD
0.1uF / 16V
30
TX_DB07
TX_DB08
2A7
31
HD_DG02
1Y4
29
4
3
2
1
2
1
TX_DB06
6
0.1uF / 16V
29
HD_DG01
1Y3
55
CLK
100
GND
56
92
GND
1Y2
57
DVDD
C556
100P_NC
75_NC
R886
R806
3
2
5
8
7
TX_DB04
TX_DB05
Vcc
TX_DB03
13
14
36
2Y6
Vcc
TX_DB02
33ohm (1005SIZERN89
X 4),1/16W
17
37
2Y5
2A6
0.1uF / 16V
2Y2
C399
TX_DB00
2Y1
30
HD_DG00
1A4
TX_DB01
33ohm (1005SIZERN88
X 4),1/16W
12
1Y10
2A5
0.1uF / 16V
C464
1A3
33ohm (1005SIZE X 4),1/16W
32
HD_DB11
GND
SC_HSYNC
TX_DE
RN87
6
7
2Y4
2A4
10
GND
11
2Y3
GND
1Y9
15
2A3
1Y8
35
HD_DB10
2A2
18
HD_DB09
2A1
19
HD_DB07
HD_DB08
1A10
GND
20
HD_DB06
1A9
1Y7
21
HD_DB05
1A8
1Y6
22
HD_DB04
C431
16
48
47
46
45
HD_DB03
GND
44
HD_DB02
1A7
43
HD_DB01
1A6
42
1Y5
41
Vcc
1A5
40
Vcc
39
C457
0.1uF / 16V
1Y4
50
1A4
49
0.1uF / 16V
TX_VSYNC
TX_HSYNC
7
6
1Y3
38
HD_DB00
1A2
SC_VSYNC
58
D17
33ohm (1005SIZE X 4),1/16W
1Y1
59
91
74ALVCH16827DGG
1A1
ENC_VCLK2
60
90
TX_VSYNC
SC_DE
TX_VCLK
1
2
3
1A3
53
GND
56
55
54
1Y2
GND
52
1Y1
1A2
51
HD_HSYNC
HD_DE
10K_NC
10K_NC
R820
75_NC
R827
C463
100P_NC
HD_VSYNC
1A1
61
89
TX_HSYNC
BYPASS_OFF
HD_VCLK2
62
88
TX_DE
1 OE1
63
87
TX_DB01
1 OE2
64
86
TX_DB02
IC916
65
85
TX_DB10
TX_DB03
33ohm (1005SIZE X 4),1/16W
66
84
TX_DB11
TX_DB04
74ALVCH16827DGG
67
83
TX_DB00
BYPASS_ON
68
82
TX_DG00
3.3V_TTL_MUX1
69
81
TX_DB05
3.3V_TTL_MUX
70
80
TX_DG02
TX_DG01
RN76
71
79
TX_DG03
TX_DR10
72
78
TX_DG04
TX_DR09
73
77
TX_VCLK
TX_DR07
TX_DR08
TX_DR11
76
DVDD
0.1uF / 16V
TX_DG05
TX_DR06
74
DVDD
C453
0.1uF / 16V
TX_DB06
1 OE1
TX_DG08
DDCSDA
75
C443
TX_DR04
0_NC
0_NC
R803
R819
C408
C411
0.1uF / 16V
+3.3VH2
TX_DR05
L841
9R005Z
10/16V
TX_DR03
L840
+1.8VH2
C475
TX_DR02
22/6.3V
8
7
TX_DR01
TX_DB07
1 OE2
TX_DG07
6
5
3
2
1
4
3
2
1
TX_DR00
1
4
23
27
2 OE1
CEC_MCU
49.9
33ohm RN75
(1005SIZE X 4),1/16W
C483
26
2Y10
2 OE2
R830
TX_DG11
28
2Y9
2A10
CEC
4.99
TX_DG09
TX_DG10
33ohm RN74
(1005SIZE X 4),1/16W
0.1uF / 16V
2A9
R799
8
7
9
10
11
12
13
14
15
2Y2
R787
33ohm RN73
(1005SIZE X 4),1/16W
16
2Y1
31
SC_DR09
TX_DR11
RN86
GND
1Y9
1uF
R771
49.9
R785
TX_DG08
TX_DB08
IC911
TX_DG09
R805
2A1
1Y8
1Y10
1uF
C428
R777
TX_DB09
TX_DG10
R826
1A10
1Y7
C439
TX_DG07
44
1A9
1Y6
29
SC_DR08
2
1
45
1A8
43
C471
3
4
7
48
47
46
GND
42
C482
1A7
GND
TX_DG06
33ohm (1005SIZE X 4),1/16W
1A6
0.1uF / 16V
SC_DR07
TX_DR10
1
5
6
56
55
54
53
52
51
50
1Y5
30
4
3
2 OE1
1A5
TX_DG04
TX_DG05
RN72
0.1uF / 16V
41
SC_DR05
SC_DR06
23
26
27
31
29
2 OE2
2Y9
Vcc
40
TX_DR07
2Y8
2Y10
1Y4
Vcc
39
SC_DR04
33ohm (1005SIZERN85
X 4),1/16W
0.1uF / 16V
GND
2A10
1Y3
1A4
38
4
3
2
1
SC_DR03
TX_DR06
GND
2A9
1A3
1Y1
37
SC_DR02
TX_DR04
TX_DR05
2A8
HD_DR10
GND
36
SC_DR01
TX_DR09
HD_DR11
1Y2
GND
35
SC_DR00
TX_DR08
30
HD_DR09
1A2
33ohm (1005SIZE X 4),1/16W
34
6
5
8
7
C451
1A1
1 OE1
32
4
3
2
1
4
3
2
1
22
2Y7
33ohm (1005SIZERN84
X 4),1/16W
21
Vcc
2A7
TX_DR03
2Y6
Vcc
20
2A6
TX_DR02
2Y5
19
2A5
SC_DG09
TX_DR00
TX_DR01
28
HD_DR08
TX_DG06
R800
16
17
18
2Y4
SC_DG08
TX_DG11
33
GND
2A4
TX_DG10
32
2Y3
GND
C420
SC_DG07
TX_DG09
24
C429
0.1uF / 16V
2A3
1 OE2
0.1uF / 16V
SC_DG06
TX_DG08
25
43
42
41
HD_DR07
2A2
40
HD_DR06
15
2Y2
2A1
39
HD_DR05
14
2Y1
13
1Y10
1A10
SC_DG05
TX_DG07
33ohm (1005SIZERN83
X 4),1/16W
1Y9
12
46
1Y8
1A9
38
HD_DR04
GND
1A8
37
HD_DR03
GND
36
HD_DR02
1Y7
35
HD_DR00
HD_DR01
1Y6
1A7
10
1A6
11
48
1Y5
SC_DG04
TX_DG06
33ohm (1005SIZE X 4),1/16W

0.1uF / 16V
1A5
SC_DG02
SC_DG03
TX_DG04
TX_DG05
RN82
C441
74ALVCH16827DGG
33
Vcc
+3.3VH2
+1.8VH2
BYPASS_OFF
49
51
1Y4
Vcc
34
HD_DG11
3.3V_TTL_MUX1
52
1Y3
1A4
45
HD_DG10
GND
1A3
53
GND
44
HD_DG09
54
1Y2
55
1Y1
1A2
47
HD_DG08
33ohm (1005SIZE X 4),1/16W
1 OE1
1A1
50
0.1uF / 16V
IC915
56
1 OE2
49
C419
10K_NC
10K_NC
HD_DG06
HD_DG07
74ALVCH16827DGG
IC912
HD_DG05
Option
C544
HD_DG04
BYPASS_ON
L
R813
OE2
OE1
3.3V_TTL_MUX
Scaling Mode Interface
10/16V
HDMI By Pass Mode Interface
11.05.17
OUTPUT
22/6.3V
INPUT
GND
0.1uF
C462
C460
C470
22/6.3V
C403
22/6.3V
0.1uF
0.1uF
C440
C415
C450
22/6.3V
C395
22/6.3V
L844
27K_NC
3.3V_TTL_MUX1
+3.3VH2
3.3V_TTL_MUX
+3.3VH2
HDMI_SCL
HDMI_SDA
300
Added_ARC_SPDIF
S0
S1
CLK1 GND
VDD ICLK
CLK2 FBIN
4.7K
R821
R828
ENC_VCLK1
S5
S6
53
54
55
56
57
58
59
60
61
S7
S4
52
S3
51
62
63
33
R814
R808
R824
REVISION
235
0.01uF
C549
SC_DR09
SC_DR08
SC_DR07
SC_DR06
11.05.17
C546
0.01uF
SC_DR05
SC_DR04
SC_DR03
SC_DR02
SC_VSYNC
SC_HSYNC
SC_DE
ANAM
MULTI. LAB
0.01uF
C548
DSP_SCLK/CLK
DSP_LRCK/DR2
DSP_S0/DR0
HDMI_MCLK
DSP_MCLK
DSP_SPDIF
HDMI_LRCK
HDMI_SDATA3
HDMI_SCLK
10
11
12
1
2
ENC_VCLK1
ISSUE
0.01uF
C545
C547
3
4
9R005Z
0.01uF
CHGND
5
6
CJP17GB210ZY CN104
M/P
0.01uF
7
8
TO DSP PCB
SCHEMATIC DIAGRAM
L847
harman/kardon
9
10
0_NC
L842
C418
11
12
C476
22/6.3V
0.1uF / 16V
C472
C414
0.1uF / 16V
0_NC
C477
R802
13
14
+1.8VA
0.1uF / 16V
64
15
16
13
17
17
C487
L846
L838
AVR 2650
HDMI_SDATA2
+3.3VH2
33
SC_DG02
14
SC_DG03
ENC_VCLK2
15
SC_DG04
V-GND
HDMI_SDATA1
SC_DG05
50
HDMI_SDATA0
V_CLK_SEL
0.1uF / 16V
VDD_IO
2*ICLK
TEST0
DGND
TEST1
REST1
SFL/MISO
46
VDD
VREF
48
ICLK
S1:LOW
0.01uF
COMP1
CLK1
S1:HIGH
0.1uF
C554
Y0
C397
Y1
IC920
MK2302S01T
9R005Z
DAC1
33_NC
R871
Y2
L839
Y3
DAC2
ARC_SPDIF_OUT
HDMI_SPDIF
0.1uF / 16V
C461
C435
10/16V
0_NC
R790
C1
DAC3
(13.5M*2=27M)
32
C2
C407
PS1
SC_DB03
100
ALSB
SDA
SCL
P_HSYNC
P_VSYNC
C3
C4
P_BLANK
C5
C6
Y4
SC_DG06
10
Y5
9R005Z
0.1uF / 16V
0.1uF / 16V
S1
SC_DG07
C402
16
100
R783
2200P
VDD
IC919
CVIADV7342BSTZ
S2
R825
220
C7
VAA
SC_DG08
11
47
R812
300
300
300
R832
R784
300
10
CLKIN_A
AGND
SC_DG09
L848
C486
10K
SCIN
R778
300
V-GND
C456
S2
12
DAC4
49
V-GND
N.C
SDCOUT V+1
R807
3.9K
+3.3VH2
13
V-GND
+3.3VA
28
29
MIXSW
31
100K
N.C
SCOUT
R791
30
R786
C458
R809
C465
10/16V
C447
SV_C_CONV
6.8K_NC
10/16V
VIN
C448
SC_DB02
16
DGND
CLOCK DOUBLER
4
17
C0
C478
CVBS_CONV
C401
10/16V
0.1uF / 16V
0.1uF / 16V
GND1
V-GND
VOUT
26
V+4
27
0.1uF / 16V
18
Y6
44
C444
19
DAC5
45
R772
SYIN
V-GND
CBSW
SYOUT
0.1uF / 16V
20
Y7
42
24
GND4
25
V-GND
V-GND
SV_Y_CONV
R833
0.1uF / 16V
C459
21
S1
YIN
10
23
YOUT
22
DAC6
40
C473
10/16V
23
REST2
43
V-GND
0.1uF / 16V
V-GND
V+2
11
22
V+3
C466
24
COMP2
39
C400
0.1uF / 16V
0.1uF / 16V
C437
SC_DB04
HDMI_SDA
HDMI_SCL
SC_DE
SC_HSYNC
SC_DB05
SC_VSYNC
SC_DB06
SC_DB07
SC_DB08
R818
15
N.C
25
14
41
13
21
GND2
12
20
N.C
PBOUT
0.1uF / 16V
26
S0
PBIN
14
19
V-GND
GND3
27
SC_VCLK
9R005Z
15
37
2200P
28
TEST2
36
220
C405
COM_Y_CONV
V-GND
R788
3.9K
29
TEST3
38
R782
30
PVDD
35
0.1uF / 16V
COM_PB_CONV
V-GND
PS2
31
EXT_LF1
34
C434
C412
COM_PR_CONV
32
25V/0.012UF
C416
C432
0.1uF / 16V
16
17
18
PROUT
V-GND
150
33
22/6.3V
9R005Z
V-GND
LPFSW PRIN
R781
20
C421
L845
NJM2566V
FS_SEL
25V/0.012UF
R789
0.15
+1.8VA
EXT_LF2
C417
150
9R005Z
0.1uF / 16V
C474
10/16V
0.1uF / 16V
C404
10K
R773
4.7K
R815
L836
IC913
L834
R829
20
C484
PGND
+3.3VH2
HD(30MHZ) MODE : HIGH

SD(13.5MHZ) MODE : LOW
R823
0.15
R835
100P_NC
C422
C449
+5VA
+3.3VA
R810
Analog Video Option
R817
75_NC
ENC_VCLK1
SC_DB09
SW_P+5V
AVR CORE
MODEL
DESIGN
CHECK
APPROVE
S.K
W.Y.YANG
G.S.WEY
11.05.17
11.05.17
11.05.17
V-GND
SHEET
1
4
DRAWING NO
HDMI TX & Encoder
CUP12328Z
AVR 2650
harman/kardon
DC/DC REGUALTOR
D
TO VIDEO
V-GND
+15VA
-15VA
IC930
GND
4
2.5V
C532
5
7
11
13
15
17
5.1K
IC929
19
SV_Y_CONV
25
IN
R876
+3.3VDD
F_CVBS
BUSY
29
OUT
+2.5VH2
SV_C_CONV
GND
PW_GND
+3.3VH2
0_NC
IPOD_PR/SY
L863
26
2.5V
22
21
CVBS_CONV
24
23
OSD_CE
4.7K
R854
OSD_SCL
4.7K
R856
R840
18
1321_SDA
20
0.1uF
C508
10/16V
0.1uF
C537
22/6.3V
C514
C535
470/16V
1321_SCL
16
COM_PB_CONV
OSD_SDA
PW_GND
BN301
GND
12K
COM_Y_CONV
14
+3.3VDD
COM_PR_CONV
0.1uF
2K
R841
L855
62k
R872
R843
0.01uF
+2.5VH1
C521
CVDSS34SR
D903
C512
1000P
0.1uF
220P
C495
C509
C489
220/25V
10UH/3A
C551
12
COM_PB_THRU
COM_PR_THRU
IN
OUT
L858
COM_Y_THRU
IC922
2
+15V_DC/DC
10
+1.8VH1
28
27
30
PW_GND
SV_C_THRU
CVBS_THRU
SW
PW_GND PW_GND
SV_Y_THRU
DDRMEM_REG_ 2.5V
FB
COMP
SS
EN
VIN
CVISI8005QTL
BS
10K
22K
R845
R846
D905
0.1uF
C498
HVDUDZS5.1BSR
OSD_H
IPOD_PB/CVBS
GND
C490
0.1uF
C530
10/16V
C522
0.1uF
N.D
FB
COMP
SW
EN
VIN
SS
BS
CVISI8005QTL
IC927
C523
22/6.3V
IPOD_Y/SC
+1.8VDD
TO INPUT
+15V_DC/DC
L856
FRONT_HDMI_Option
150uF/10V
12K
2K
0.1uF
C506
R838
R852
ADC_REG_ 1.8/3.3V
C493
CVDSS34SR
D904
C513
1000P
220P
C527
0.1uF
0.01uF
62k
R873
C531
C518
220/25V
10UH/3A
C552
TXEN
V-GND
3.3V
IC926
V-GND
11
CEC_MCU
IC928
15
COMP
SW
3
17
GPROBE_TXD
GND
13
C501
C516
V-GND
V-GND
V-GND
10/16V
0.1uF
C502
0.1uF
C507
22/6.3V
+3.3VDD
14
16
GPROBE_RXD
FB
EN
VIN
14
SS
BS
13
OSD_H
IN
8
CVISI8005QTL
GND
OUT
IC923
12
1321_SCL
1321_SDA
15
1.8V
10
UART_TX
+1.8VA
UART_RX
V-GND
100_NC
/RESET
C538
C529
V-GND
V-GND
R875
16
V-GND
10/16V
0.1uF
0.1uF
C496
C503
22/6.3V
HDMI_MUTE
BUSY
PW_GND
10
PW_GND
11
BUSY_CHECK
R877
12
OSD_CE
OSD_SCL
Option
CJP17GB210ZY CN105
OSD_SDA
+5VA
+3.3VA
17
0_NC
R885
IN
GND
OUT
5.1K
R851
V-GND
+15V_DC/DC
L862
B
470/16V
27K
0.1uF
TO POWER
L850
CLZ9Z014Z
+15V_DC/DC
L860
+5VH1
+15VA
V-GND
V-GND
-15VA
V-GND
PW_GND
L864
CLZ9Z014Z
7
6
5
5
PW_GND
C510
C491
V-GND
PW_GND
2
V-GND
220/25V
C519
GND
$$$17270
GND
9R005Z
L861
Out In
BN61
+5VA
OUT IN
0.1uF / 16V
0.1uF
L859
C536
KIA1117S50
3
10/16V
0.1uF / 16V
IC924
C525
CVIKIA7809AF IC925
+8VA
PW_GND
L852 10UH/3A
NC
L857
Option
V-GND
CWB07
+15VA
PW_GND
Option
+15VA
C528
SCALER&Analog_REG
1200/35V
2.2K
C500
R844
5.1K
62k
R874
R847
C505
0.01uF
R839
CVDSS34SR
D902
C539
1000P
220P
0.1uF
C520
C534
C511
220/25V
10UH/3A
C553
0.01uF
C533
+3.3VDD
PW_GND
+1.8VDD
L849
CLZ9Z014Z
C526
C488
10/16V
0.1uF / 16V
L854
CLZ9Z014Z
+3.3VH1
L851
CLZ9Z014Z
C517
0.1uF
C515
C542
10/16V
+1.8VH2
C494
10/16V
0.1uF / 16V
L853
CLZ9Z014Z
+3.3VH2
REVISION
A
SCHEMATIC DIAGRAM
M/P
AVR CORE
MODEL
SHEET
1
4
ISSUE
ANAM
MULTI. LAB
236
DESIGN
CHECK
APPROVE
S.K
W.Y.YANG
G.S.WEY
11.05.17
11.05.17
11.05.17
DRAWING NO
11.05.17
POWER&CONNECTOR
1
AVR 2650
harman/kardon
237
AVR 2650
harman/kardon
* DEFINITION OF I2C REGISTER ( NJW1321 )
I2C BUS FORMAT
MSB
S(1BIT)
LSB
MSB
SLAVE ADDRESS(8BIT)
LSB
A(1BIT)
DATA(8BIT)
MSB
S : Starting Term
LSB
A(1BIT)
DATA(8BIT)
A(1BIT)
A : Acknowledge Bit
P(1BIT)
P : Ending Term
SLAVE ADDRESS
MSB
Slave Address(8BIT)
MSB
ADR(1BIT)
R/NOT W : Set the Write Mode or Read Mode.
Hex
ADR : Set the Slave Address by " ADR" terminal.
R/NOT W(1BIT)
R/NOT W = 0 : WRITE MODE, ADR = 0/1 ; ADR=0 Hex:94(h), ADR=1 Hex:96(h)
CONTROL REGISTER TABLE
R/NOT W = 0 : READ MODE, ADR = 0/1 ; ADR=0 Hex:95(h), ADR=1 Hex:97(h)
<WRITE MODE>
BIT
NO.
D7
DATA 1
D6
PS1
D5
DATA 2
PS : POWER SAVE
D4
PS2
D3
D2
D1
OUT1
AUX0
D0
=> PS = 1 ; POWER SAVE ON (MUTE), PS = 0 ; POWER SAVE OFF (OUT ON)
OUT2
AUX1
AUX2
OUT : OUTPUT
AUX3
AUX : AUXILIARY (CONTROL SIGNAL OUTPUT)
<READ MODE>
BIT
NO.
EUR Ver.
ONLY
D1
D0
PORT3
PORT : INPUT
SW1
SW2
D2
PORT2
47
10
SCL
11
12
13
2
12
9
11
13
14
16
15
75
R572
75
R568
75
33
1321_SCL
OSD_DATA
OSD_CLK
14
21
R571
17
R576
15
33
ADR
PORT3
PORT2
R567
75
R575
48
C141
1/50V
COM_Pr_CONV
1321_SDA
16
19
SDA
COM_Y_CONV
VGND
17
Pr3
18
18
GND
COM_Pr_THURE
COM_Pb_CONV
C160
100/16
19
DGND
0.1uF
20
VREF
COM_Y_THURE
VGND
21
V+
CVBS_THURE
VGND
R569
+9VV
C181
Pb_OUT
Y_OUT
Pb3
470/10V
COM_Pb_THURE
22
V+
Pr1
Y2
PORT1
IC901
NJW1321FP1
Y3
75
R574
23
C149
AUX2
25
470/10V
10/50V
AUX3
Y_OUT2
26
PORT0
Pb_OUT2
27
AUX0
AUX1
28
V+
46
0.01uF
2P
29
V+
45
Y2
C115
30
Pb1
2P
C114
75
R505
31
Pr_OUT2
Pr2
44
C140
1/50V
C121
75
32
V+
43
0.01uF
R506
33
Y1
42
C120
34
Pr4
Pb2
2P
C113
75
R504
41
C139
1/50V
Y1
35
Pr_OUT
Pb4
40
V+
39
0.01uF
37
24
C119
Pb2
36
Y4
38
V+
C138
1/50V
V+
2P
C112
75
R503
C168
SV_Y_THURE
SV_C_THURE
75
7
Pb1
OSD_CE
To HDMI B'D
C172
0.01uF
C118
6
VGND
VGND
R573
6
470/10V
+15VA
-5VA
75
20
2P
C110
75
R501
C136
1/50V
-15V
C169
0.01uF
+15VV
Pr2
75
R570
10
470/10V
22
2P
C111
75
R502
& COMPONENT IN1
D3
CN41
C171
C137
1/50V
COMPONENT IN2
D4
PORT1
C117
C116
JK91
D5
0.01uF
D6
PORT0
VGND
23
22P-->2P
24
Pr1
SW3
SW4
VIDEO MUX PART
D7
DATA
CVBS_CONV
26
25
SV_Y_CONV
SV_C_CONV
FRONT_CVBS
28
VGND
IPOD_PB/CVBS
27
IPOD_PR/SY
IPOD_Y/SC
30
29
IPOD_PR/SY
IPOD_Pb/CVBS
IPOD_Y/SC
VGND
16
14
13
11
100/16
0.022u
C152
VSS
10
B
VIDEO1 IN
C187
SW4
VIN3
SW4
12
IC41
NJM2595M
IC905
75
15
VCC
VIN2
S3(SW3)
VID2
6dB
SW2
S4(SW4)
S1(SW1)
75
DVD
+5VV
S7(SW2)
VO2
C142
0.022u
4
S2(SW2)
6dB
100/16
S6(SW1)
S5(SW5)
C184
VIDEO3
V4,IPOD
75
6dB
VO3
SW2
SW5
VIN4
SW3
VID3
GND
VIN1
VID1
SW1
SW4
VIDEO2
SW3
SW5
SW3
VIDEO1
SW1
SW1 SW2
V01
*NJM2595M OPTION
==>V_MUTE "LOW" ACTIVE
VIN5
1K
FUNC.
DVD
-5VA
R577
NJM2595M
CVBS
+5VV
+9VV
+15VV
B
IC903
CVIKIA1117S50 IC904
C125
CVIKIA7809AF
75
R510
REC OUT
C161
GND
C197
C177
C183
OUT IN
10/50V
0.1uF
GND
Out In
0.1uF
C174
10/50V
C194
0.1uF
C126
10/50V
75
R509
10/50V
VIDEO2 IN
10/50V
1000P
C109
R508
MONITOR OUT
75
-5VA
-15V
CVIKIA7905PI IC902
GND
C175
C176
10/50V
C195
0.1uF
open-> connection
OUT IN
10/50V
JK92
C179
75
VIDEO(SILVER)
0.1uF
1000P
C108
R507
REVISION
A
SCHEMATIC DIAGRAM
MP
AVR CORE
MODEL
DESIGN
238
CHECK
APPROVE
W.Y.YANG
G.S.WEY
11.05.17
11.05.17
1
3
12361SEMZ
11.05.17
SHEET
DRAWING NO
S.K
(VIDEO)
AVR CORE
S.K
AVR 2650
harman/kardon
5
I-POD PART
SIRIUS PART
+8V
0.1uF
GND
-5VA
+5VV
AVR365x Only
+8V
+8V
C185
0.1uF
47/16
C182
C163
0.1uF
47/16
C157
C145
14
13
R530
12
HVI74HCU04AFNG
IPOD_PB/CVBS
10
R531
10/50V
10
11
12
R532
75_NC
R580
13
14
R579
100K
100K
AVR2650/3650 : CVIMC7805VA
SIRIUS_TX
3
21
20
AVR265/365 : Not USE
270
TO_AVR
C127
13
R517
10/50V
CVIAZ4580MTR-E1
1
2
R513
47K
3.3K
220P
220P
C102S
GND
C128
SIRIUS_L
1
22
AGND
R591
4.7/50V
C147
33P
090322 DELETE
33P
R529
R523
R520
R518
C151
49.9K(1%)
49.9K(1%)
5.1K(1%)
10K(1%)
10/50V
0.022u
220/16V
C193
IPOD_R
C153
090322 DELETE
AGND
470K
R583
0.1uF
4700P
C190
SIRIUS_R
4.7/50V
R581
Q904
AGND
22
1K(1%)
C103
4.7
C150
R514
-15V
R589
IC908
CVITL072CDR
R526
C148
R588
R585
R-CH
470K
R528
49.9K(1%)
C102
IPOD_R_OUT
D706 1SS355
IC907
4700P
R593
0
R592
R590
R527
1K
SIRIUS_R
SIRIUS_RST
33P
1K(1%)
SIRIUS_Audio
33P
49.9K(1%)
C124
090322 DELETE
IPOD_L
C122
C123
IPOD_L_OUT
AGND
SIRIUS_L
C129
10K(1%)
R578
R515
1K
C104
R519
5.1K(1%)
10K
AGND
AGND
R516
R521
49.9K(1%)
33P
C101
16
17
AUDIO_RETURN
18
35
R525
49.9K(1%)
L-CH
R522
15
R524
1K(1%)
VIDEO_RETURN
4700P
14
IPOD_CV(PB)
AGND
JK93
C105
47K
12
IPOD_R
IPOD_Audio
0
AGND
GND
GND
CJP05GB46ZY
R587
11
10
IPOD_SY(PR)
IPOD_SC(Y)
IPOD_L
CN52
22
R586
C189
0.022u
C191
C106
220/16V
R584
0.1uF
FROM_AVR
470/10V
270
26
27
28
29
30
31
33
32
C188
22
R548
25
I-RX
DETECT
34
+5VDD
+15VV
0.1uF
I-RX
24
R549
23
I-TX
I-TX
22
JK94
C162
0.022u
19
IPOD_Y/SC
C206
R534
10K
8V
CJJ9L016Z
GND
1uF
Change:R537(75ohm) --> C206(1uF)
36
1K
C205
IPOD-Y
10/50V
GND
C132
VGND
100
VOUT
R540
AGND
75_NC
47/16
0.1uF
C159
V+
C146
1uF
C156
2.2K
R511
75_NC
3
4
11
0.1uF
V+
GND
IC906
VIN
IC910
10/50V
75
R541
C133
C107
IPOD_PR/SY
C204
IPOD-PB
+8V
470/16V
C196
SIRIUS_RX
1uF
IPOD_SC(Y)
100
VIN
VGND
10/50V
IPOD-PR
10/50V
C134
R542
R596
IC911
HVINJM2581MTE1
C158
100
R597
IC912
VOUT
R543
0.1uF
C135
10/50V
75
L802
R544
100
IPOD_SY(Pr)
R545
R512
10/50V
10/50V
C130
SIRIUS-RX
VGND
5
100
C155
C154
VOUT
R533
C144
V+
VIN
IC909
10/50V
75
R538
100
C131
47/16
IPOD_CV(Pb)
R539
D705 1SS355
R582
4.7
C192
AGND
0.1uF
AGND
FROM_AVR
+5VV
+8V
+15VV
+5VDD
3
4
4.7K->470K
SIRIUS_TX
change
IPOD_DET
SIRIUS_RX
R594
SIRIUS_RST
1.8K->10K
change
R595
10K_NC
1K
FROM RS232 B'D
470K
R547
2.2K
R546
IPOD_DET
Q901
TO_AVR
CN40
AGND
HVTKRC102S
REVISION
MP
SCHEMATIC DIAGRAM
ARV CORE
MODEL
239
DESIGN
CHECK
APPROVE
S.K
W.Y.YANG
G.S.WEY
11.05.17
11.05.17
11.05.17
SHEET
2
3
DRAWING NO
12361SEMZ
(IPOD&SIRIUS)
ARV CORE
AVR 2650
harman/kardon
(IPOD&SIRIUS)
RS232 PART
+15VV
+12VA
R598
0_NC
IC913HVIKIA7812API
C198
C170
COMMON
0.1uF
IN OUT
10/50V
0.1uF
C173
C180
10/50V
R603
4.7
R602
4.7
+5VD
connection change
+12VA
R557
10K
R563
C143
0.01uF
2
10
4.7
AVR265_2650_only
10K
Z_1 TRIG
Z_2 IR_IN
AVR365_3650_only
21
Q906
1K
Q905
HVTKRA102S
R556
+8V
+5VD
JK98
1
22
24
R559
0.01uF
C164
+15VV
ST+5V
1SS355
0_NC
1SS355
CVD1SS355T
100
ST+5V
R551
D701
D704
R550
1
2
3
4
5
SIRIUS_RX
SIRIUS_RST
D708
1SS355
HVTKRC102S
FROM RS232 B'D
SIRIUS_TX
BN51
D707
Z_1 TRIG
4.7
1SS355
IPOD_DET
R561
R562
FROM_AVR
TO_AVR
JK96
CJJ2D008Z
Q903 KTA1266
10K
R552
V+
C1-
0.1uF
IC914
74LCX32TTR
10K
10K
R599
10
11.02.16
15
Q909
0.1uF
GND
HVTKRC107S
15
14
0.1uF
open
16
C200
Vcc
16
22P
14
R601
D710
T2out
HVTKRC102S
11
Q910
HVTKRA107S
10
R554
ADD
2
10
Q902
HVTKRA107S
220
4
R564
220
4
13
11
14
12
10
R565
2
KP1010B
open
AVR265/2650 Only
16
R558
47K
TO_AVR
FROM_AVR
RS232_RX232
Z1_TRIG
15
18
ST+5V
17
ZONE1_IR
ZONE2_IR
RS232_TX232
ST+5V
11.02.16
MP
IC916
SIRIUS_RX
SIRIUS_TX
SIRIUS_RST
10K
IPOD_DET
+5VD
Z_1 IR_IN
R560
1SS355
+8V
IR_OUT
IC915
D702
JK97
KP1010B
HVTKRC107S
Q908
1
22
24
21
47K
R2in
11.02.16
R555
R2out
10K
T2in
Q911
ST+5V
47K
V-
12
0.1uF
T1in
R1out
13
C2-
C165
12
C166
0.1uF
47
10K
R611
13
11
C2+
R1in
1SS355
ST+5V
1SS355
D709
0.1uF
T1out
R612
C167
10
C203
L801
C1+
C201
22P
0
0
C202
R608
R609
11
IC917 HVIST202EBW
R605
R553
1
6
CJJ9V001Z
MALE
2
7
R607
TXD
12
IC918 CVIILX2323DT
RS232
R604
R606
JK95
USE CROSS CABLE
FEMAIL
R605,R606,R608
RXD
13
Q907
KTA1266
C199
14
MAIL
R604,R607,R609
FROM INPUT
BN53
REVISION
SCHEMATIC DIAGRAM
SHEET
ARV CORE
MODEL
240
DESIGN
CHECK
APPROVE
S.K
W.Y.YANG
G.S.WEY
11.05.17
11.05.17
11.05.17
3
3
DRAWING NO
12361SEMZ
(RS232)
AVR 2650
CN61
harman/kardon
HDMI
CN105
DC15V
+15V
-15V
POWER1
P_FAIL
S1
CN20
5P WIRE
POWER2
BN96
7P WIRE
D15V
P_UP
-20
+20
IPOD SIRIUS
MUTE PO
WF103
DCDC
DC15V
CN96
8P CN12
CN82
+15V
-15V
DC15V
BN20
CN91
TRANS
BN14
S/T PCB
6P
BN14-1
6P
CN61
BN15
BN73
CN73
BN15-1
FRONT
CN71
FAN
CN93
CN89
AC45V VFD AC
5P WIRE
BN53
AVR265 USB
CN10
FAN TEST
CN92
AC CORD
CN72
REVISION
BN74
V/R PCB
CN74
241
BN20
31 P C/C
CN90
MOMS
5P WIRE
5P WIRE
+15V
ST5V
-15V
+15V
+5VD
CN1
9P WIRE
7P WIRE
CN11 8P CN11
DATA
USB5V
+5V
27P C/C
AMP
BN20
+15V
ST5V
H/P
BN61
18P
WF101
+5V
+3.3_1
+3.3_2
CN71
9P WIRE
ST5V
+5VD RS232
BN71
+15V
R904
AC
11P WIRE
AUDIO
5P WIRE
CN51
P-FAIL
S1
30P
BN52
WF104
+3.3V
+3.3V
+15V
+12V?
-15V
+5V
ST5V
CN20
P-U
9P WIRE
13P WIRE
BN301
17 P C/C
17 P C/C
+9V +8V
+15
+5V
VIDEO -15
-5V
IPOD SIRIUS
CN301
CN20
BN52
+15V/DC15V
-15V
CN104
WF105
5P WIRE
MAIN TRANS
SCHEMATIC DIAGRAM
AR CORE
MODEL
DESIGN
CHECK APPROVE
K.M.S
L.J.H
Y.W.Y
11.05.17
11.05.17
11.05.17
SHEET
1
1
DRAWING NO
Wiring

Harman-Kardon AVR2650 Service Manual PDF

Uploaded by

Copyright:

Available Formats

Harman-Kardon AVR2650 Service Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Harman-Kardon AVR2650 Service Manual PDF

Uploaded by

Copyright:

Available Formats

harman/kardon

8500 Balboa Blvd..

Each precaution in this manual should be followed during servicing.

ANY MEASUREMENTS NOT WITHIN THE LIMITS

Surround system adjacent

Dolby Pro Logic/DPLII: 40dB

Frequency response (@ 1W):

10Hz 130kHz (+0dB/3dB)

High instantaneous current

Version 1.4a with 12-bit Deep Color

10Hz 8MHz (3dB)

Video frequency response

Signal-to-noise ratio (IHF-A):

AVR 3650/AVR 365: 110W per channel, two channels

NTSC (AVR 3650/AVR 2650);

AVR 3650/AVR 365: 110W per channel, two channels

120V AC/60Hz (AVR 3650/AVR 2650);

17-5/16" x 6-1/2" x 17-1/8"

(AVR 3650/AVR 365): 27.25 lb (12.4kg)

Depth measurement includes knobs, buttons and terminal connections.

Usable sensitivity IHF:

Signal-to-noise ratio (mono/stereo):

520 1710kHz (AVR 3650/AVR 2650)

Usable sensitivity (loop):

Distortion (1kHz, 50% mod):

FOAM PAD (L)

Continued on next page

Front-Panel Controls, continued

Front-Panel Controls, continued

Power Indicator: This LED has three possible modes:

LED glows white: Indicates that the AVR is turned on.

Message display: Various messages appear in this two-line display in response

Left/Right buttons: Use these buttons to navigate the AVRs menus.

Up/Down buttons: Use these buttons to navigate the AVRs menus.

The Bridge IIIP

Rear-Panel Connectors (AVR 3650 shown)

Notes on using the HDMI Monitor Out connector:

When connecting a DVI-equipped display to the HDMI Monitor Out connector,

Continued on next page

Rear-Panel Connectors, continued

Rear-Panel Connectors, continued

SIRIUS Tuner connector: Connect a SIRIUSConnect satellite radio tuner module

Radio Antenna connectors: Connect the included AM and FM antennas to their

Subwoofer connector: Connect this jack to a powered subwoofer with a line-level

System Remote Control Functions

System Remote Control Functions

AVR Power On/Off

Device Power On/Off

(AVR 3650/AVR 365 only)

Channel Up/Down and

System Remote Control Functions, continued

System Remote Control Functions, continued

Types of Home Theater System Connections

Types of Home Theater System Connections

Analog Audio Connection

Surround Back/Front Height Left/Right

Digital Audio Connection

Coaxial (input or output)

Optical Record Output