Introduction To Ionic Covalent Bonding

Pre-Lab Questions
1. Define ionic bond:

2. Define covalent bond:

3. What types of atoms compose each type of compound only metals, only nonmetals, or both?

Procedure, Part A (Macro Tab)

1. Open the Sugar and Salt Solutions simulation on the PhET website by following the link below and clicking,
Run Now!: http://phet.colorado.edu/en/simulation/sugar-and-salt-solutions
2. Drag the conductivity tester, labeled A, into the beaker of water. Place the negative and positive electrodes into
the water, but not touching the bottom of the beaker. When electricity is conducted by the solution, the light
bulb will light up the stronger the electric current, the brighter the bulb will glow. Record any observations.
3. Click on the salt shaker, labeled B, and drag your mouse back and forth. This will shake the salt into the water.
As you add salt, pay attention to the light bulb on the conductivity tester. Continue to add salt until the shaker
is empty. Record observations. Then click the Remove salt button to reset the simulation
4. Click the sugar bubble in the solute selector, labeled C, to switch from salt to sugar. Then repeat step 3, this
time using the sugar shaker. Record observations.
5. Click on the Micro tab at the top of the simulation, labeled D, to switch to a new simulation for part B.
Introduction to Ionic & Covalent Bonding
Procedure, Part B (Micro Tab)

6. Click on the salt shaker, labeled A, and drag your mouse back and forth. This will shake the salt into the water.
Pressing pause, labeled C, will stop the salt crystals mid-air so you can see them before they dissolve.
7. Observe how the crystal behaves once in the water. Record observations in the Ionization in Water section of
the data table.
8. Click the sucrose bubble in the solute selector, labeled D, to switch from salt to sugar. Then repeat steps 6
and 7, this time using the sugar shaker. Record observations.
9. You can test other solutes by clicked the right arrow in the solute selector, labeled D.
10. To get an even further zoomed in view, click on the water tab, labeled E and repeat the simulation by dragging
salt and/or sugar into the water.

Procedure, Part C

11. Use the Flinn MSDS search to locate the MSDS for sodium chloride (salt) and sucrose (sugar):
http://www.flinnsci.com/msds-search.aspx
12. Using the MSDS sheets for salt and sugar, locate their melting points. Record in the data table below.
13. Using the MSDS sheets for salt and sugar, locate the information on solubility. Record in the data table below.

Data Table

Substance
Melting
Point
Solubility in Water
(yes or no)
Electrical
Conductivity
(yes or no)
Ionization in Water
(yes or no)
Pure Water
H
2
O

N/A N/A
Salt
NaCl

Sugar
C
12
H
22
O
11

Analysis Questions

1. Based on their chemical formulas, state whether the substances tested above are covalent or ionic.

2. A data table is provided below with information on substances not tested in the simulation. Complete any
missing information by looking up the MSDS sheets for each chemical using the same link provided in step 11 of
the procedures (for part C).
Substance
Phase at 20C
(solid or liquid)
Melting
Point
Solubility in
Water
Electrical Conductivity
in Water
Type of Bond
potassium chloride
KCl
solid Yes Yes
benzoic acid
C
6
H
5
COOH
solid 122.4C None detected covalent
ethyl alcohol
C
2
H
5
OH
liquid Yes None detected
iron (III) sulfate
Fe
2
(SO
4
)
3

480C Yes ionic
oleic acid
C
18
H
34
O
2

13.4C No None detected
nitrogen
N
2

gas -210C Slightly None detected

3. Using the data you gathered during the simulation, as well as the data table from the previous question, what
are some properties exhibited by covalent (molecular) compounds?

4. What are some properties exhibited by the ionic compounds tested in the simulation and/or shown in the data
table in question 2?

5. Although both sugar and salt are soluble in water, the way in which they dissolve is not shown the same in the
simulation. How is their dissolving process different? Explain why these differences exist.

6. What would the simulation have shown if oleic acid was added to water? Would it look different than what was
shown for sugar and/or salt? Explain.

7. When some ionic compounds dissolve, not all of their bonds dissociate. What kind of conductivity would you
expect such a solution to have? Explain.

8. Based on the formula, predict whether each of the following compounds is primarily ionic or primarily covalent.
a. sodium iodide (NaI) d. ammonia (NH
3
)

b. methane (CH
4
) e. glucose (C
6
H
12
O
6
)

c. calcium chloride (CaCl
2
)

Introduction To Ionic Covalent Bonding

Uploaded by

Copyright:

Available Formats

Introduction To Ionic Covalent Bonding

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Introduction To Ionic Covalent Bonding

Uploaded by

Copyright:

Available Formats

Pre-Lab Questions

1. Define ionic bond:

You might also like