TDS 7728-6028

Technical Data Sheet
LOCTITE LIOFOL LA 7728/LA 6028

LOCTITE LIOFOL LA 7728/LA 6028 has the following
Product characteristics: Ready-to-Use Mixture:
Viscosity,Brookfield
Technology Polyurethane
RVTDV II, 40 °C, Spindle 3 ~1500 mPas
Product Type Laminating adhesive
Condition Solvent-Free Increase of Viscosity
Components Two component - requires mixing
After 30 minutes, ~2,500 mPas
Application Film/Film laminates for food ~4,500 mPas
After 45 minutes
packaging
Performance Standard Performance
Cure Room temperature cure after mixing
Compliance and regulations:
Appearance Clear to light Yellow
LOCTITE LIOFOL LA7728/LA 6028 contains aromatic
Base
isocyanates. We therefore recommend migration
LA 7728 testing of the fully cured material under conditions of
Appearance Clear to light Yellow use, particularly with high temperature applications, to
Hardener LA demonstrate compliance with the limits for primary
6028 aromatic amines. The responsibility for compliance with
Mix Ratio, by 100 :80 (metallized) the specific conditions is with the converter and not with
weight - Base : 100 :60 (Poly) the adhesive supplier.
Hardener
DIRECTIONS OF USE
Application Areas: Preliminary Statement:
LOCTITE LIOFOL LA7728/ LA 6028 is a solvent-free Prior to application it is necessary to read the Safety
adhesive combination which is suitable for the Data Sheet for information about precautionary
lamination of transparent films and metalized films for measures and safety recommendations. Also, for
food packaging. chemical products exempt from compulsory labeling,
the relevant precautions should always be observed.
Product Properties: Please also refer to the local safety instructions and
Reaction of the two components produces a high contact Henkel for analytical support.
polymer adhesive film which shows good adhesion on
Protective Measures:
various substrates. The completely cured adhesive film
is transparent, odorless, elastic and age-resistant. LOCTITE LIOFOL LA 7728/ LA 6028 contains Poly-
Isocyanates. To avoid the emission of volatile
Isocyanates into the working area, the coating unit has
TECHNICAL DATA to be equipped with an air-supplied hood. This will make
sure that the TLV-value (max concentration in air) does
LOCTITE LIOFOL LA 7728 not exceed limit. Safety regulations with regard to
Solid Content, % 100 handling of Isocyanates have to be followed as per the
Viscosity, Brookfield - LVT, 40 °C, 1500 to 3000 guidelines issued by the International Isocyanate
mPas: Spindle 3, speed 30 rpm Institute.
Specific Gravity, @25°C 1.18
Component NCO component
Application:
LOCTITE LIOFOL LA 7728/LA 6028 can be applied on
LOCTITE LIOFOL LA 6028 laminating machines with multi-roller application
Solid Content, % 100 system.
Viscosity, Brookfield - LVT, 25 °C, 500-1500
mPas: Spindle 3, speed 30 rpm
Specific Gravity, @25°C 1.11
Component OH component
Henkel Adhesives Technologies India Pvt. Ltd.

A Henkel Company
Phone +91 22 39296600. Fax +91 39296602
www.henkel.com
7728_6028.pdf Status: Jan./2017
1
Application Weight: Classification:
The application weight may range from 1.5 to 3 g/m² dry Please refer to the corresponding safety data sheets
depending on the film or foil combination and the for details on:
intended use of the laminate. For printed laminates the Hazardous Information
weight has to be adjusted to higher weight accordingly. Transport Regulations
It should be approx. 0.5 g/m² higher than the print gsm Safety Regulations
Pot Life:
Please refer to the Technical Data section of this ADDITIONAL INFORMATION
datasheet. Film Requirements:
Working Conditions: Film additives - particularly slip agent content in LDPE,
Precise web tension control together with a suitable MDPE and CPP films - packed goods, printing inks, pre-
winding program avoids tunneling as well as treatment and coating of films are of significant
telescoping and curling effects. importance to the intended use of the laminates and
may affect the performance properties either straight
Cleaning: away or later. Laminates of high slip containing films,
In case of a machine stop (for more than 30 minutes) CPA films and white pigmented PE films, especially in
the coating unit has to be cleaned with solvents/ combination with EVA, bear the risk of migration of
plasticizer mixture (observe safety precautions) or monomeric MDI. This can cause negative influences on
products of the LOCTITE LIOFOL CL range (separate the filling good and may lead to antiseal effects.
datasheets available upon request). The 2 component Therefore, practical laminating tests as well as
dosing unit has to be cleaned. The same cleaning checks on the laminates are necessary before
procedure has to follow at the end of the run. going into full scale production. The deep draw
Curing: properties of film/film laminates have to be checked
since oriented films (OPA, OPP) show a tendency to
Manufacture of triplex laminates is possible 24-48 hours tunnelling upon the influence of higher temperatures.
after duplex production. Complete curing will be Further detailed information can be obtained from our
achieved after 7-14 days of storage at room "Technical Guide Line for Laminating with Liofol
temperature depending on film combination and Laminating Adhesives".
intended use of the laminates.
Product Range:
STORAGE Apart from LOCTITE LIOFOL LA 7728/LA 6028, we can
Once opened, containers have to be closed tightly again offer the following products for the manufacture of
and the material should be consumed within a short film/foil laminates:
period. When stored in a dry and cool place in the Solvent-based, solvent-less and waterbased
original unopened containers storage life is as follows. laminating adhesives for flexible packaging and
special applications
Shelf life:
LOCTITE LIOFOL LA 7728, months: 9
Adhesives for High Gloss Lamination
LOCTITE LIOFOL LA 6028, months: 9 Primer for Extrusion and PVDC-coating
Coldseal Adhesives
Recommended Storage Temperature, °C: -5 to 25 Heatseal Coatings
To obtain product specifications please ask for the

relevant technical datasheets.
Disclaimer:
The Information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product
are based on our knowledge and experience of the product as at the date of this TDS. The product can have a variety of different
applications as well as differing application and working and conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them,
as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such
suitability of our product. Any liability in respect of the information in the Technical Data Sheet or any other written or oral
recommendations regarding the concerned product is excluded, except if otherwise explicitly agreed and except in relation to death
or personal injury caused by our negligence and any liability under any applicable mandatory product liability law.
Henkel Adhesives Technologies India Pvt. Ltd.

A Henkel Company
Phone +91 22 39296600. Fax +91 39296602
www.henkel.com
7728_6028.pdf Status: Jan./2017
2

TDS 7728-6028

Uploaded by

Copyright:

Available Formats

TDS 7728-6028

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TDS 7728-6028

Uploaded by

Copyright:

Available Formats

Technical Data Sheet

LOCTITE LIOFOL LA 7728/LA 6028

Henkel Adhesives Technologies India Pvt. Ltd.

To obtain product specifications please ask for the

Henkel Adhesives Technologies India Pvt. Ltd.

You might also like