Dec 3000 m300 Manual

DEC 3000 Model 300 Series AXP
Hardware Reference Guide

Order Number: EKPELCNOG. C01
Digital Equipment Corporation, Maynard, MA
Second Printing, January 1994

The information in this document is subject to change without notice and
should not be construed as a commitment by Digital Equipment Corporation.
Digital Equipment Corporation assumes no responsibility for any errors that
may appear in this document.
Digital Equipment Corporation, 1994.
All Rights Reserved.
Printed in U.S.A.
The postpaid Readers Comments form at the end of this document requests
your critical evaluation to assist in preparing future documentation.
The following are trademarks of Digital Equipment Corporation: AXP,
Alpha AXP, DEC, DEC Open3D, DEC PHIGS, DECchip, DECnet, DECwindows,
Digital, OpenVMS, RX, RZ, ThinWire, TURBOchannel, VAX DOCUMENT and
the DIGITAL logo.
Open Software Foundation is a trademark of, and Motif, OSF, OSF/1 and
OSF/Motif are registered trademarks of the Open Software Foundation, Inc.
CD is a trademark of Data General Corporation; ISDN is a registered
trademark of Fujitsu Network Switching of America; MIPS is a trademark
of MIPS Computer Systems, Inc.; PostScript is a registered trademark of Adobe
Systems Incorporated.
All other trademarks and registered trademarks are the property of their
respective holders.
FCC NOTICE: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference, in which case users
will be required to correct the interference at their own expense.
S2437
This document was prepared using VAX DOCUMENT Version 2.1.
Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xi
1 Introduction to Your System

Chapter Overview . . . . . . . . . . . . . . . . . . . .
Product Description . . . . . . . . . . . . . . . . . . .
Operating Systems . . . . . . . . . . . . . . . . . . . .
Graphics Capabilities . . . . . . . . . . . . . . . . . .
Integrated Services Digital Network (ISDN)
Audio Capabilities . . . . . . . . . . . . . . . . . . . .
System Personalization Capabilities . . . . . .
Firmware Update Utility . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
11
12
17
19
111
112
113
114
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recording Information Before Making Changes . . . . . . . . . . . . .
Understanding SCSI IDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preparing Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Identifying and Locating Options . . . . . . . . . . . . . . . . . . . . . . . .
Removing and Installing a Removable-Media Drive . . . . . . . . . .
Removing and Installing a Fixed Disk Drive . . . . . . . . . . . . . . .
Removing and Installing a Memory Module . . . . . . . . . . . . . . . .
Removing and Installing a TURBOchannel Option (For Models
300/300X/300LX Systems) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing and Installing the CPU Module . . . . . . . . . . . . . . . . .
Removing and Installing the Power Supply . . . . . . . . . . . . . . . .
Removing and Installing the System Module . . . . . . . . . . . . . . .
Restoring the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
21
23
212
213
221
222
227
233
.
.
.
.
.
238
244
246
250
255
2 Adding, Removing, and Replacing Internal Options
iii
3 Connecting External Options

Chapter Overview . . . . . . . .
Headset . . . . . . . . . . . . . . . .
Tablet . . . . . . . . . . . . . . . . . .
Printers . . . . . . . . . . . . . . . .
Modems . . . . . . . . . . . . . . . .
Expansion Boxes . . . . . . . . .
Compact Disc Drive . . . . . . .
External Device Connections
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
31
32
32
33
33
34
35
36
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
41
43
46
48
415
416
420
424
425
429
430
431
432
445
458
459
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . .
Secure Console Commands . . . . . . . . . . . . . . . .
Invoking the Password Security Feature . . . . . .
Changing, Erasing, and Disabling the Password
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
51
52
53
57
4 Using Console Commands

Chapter Overview
Before You Begin .
Diagnostics . . . . .
BOOT . . . . . . . . . .
CONTINUE . . . . .
DEPOSIT . . . . . . .
EXAMINE . . . . . .
HALT . . . . . . . . . .
HELP . . . . . . . . . .
INITIALIZE . . . . .
LOGIN . . . . . . . . .
REPEAT . . . . . . . .
SET . . . . . . . . . . .
SHOW . . . . . . . . .
START . . . . . . . . .
TEST . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
5 Using the Password Security Feature
iv
6 Using an Alternate Console Device

Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Alternate Console Feature . . . . . . . . . . . . . . . . . . . . .
61
62
7 Troubleshooting by Visual Inspection

Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Troubleshooting Tables . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
72
710
8 Advanced Diagnostics
Chapter Overview . . . . . . . . . . . . . .
Preliminary Power-up Test Displays
Messages from Other Tests . . . . . . .
Problem Worksheet . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
81
82
811
812
Appendix Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A1
A2
A Hardware Specifications
B Internal Options: Specifications and SCSI ID Settings

Appendix Overview . . . . . . . . . .
RX26 Drive Specifications . . . . .
RX26 Diskette Specifications . . .
RZ25 Fixed Disk Specifications .
RZ25L Fixed Disk Specifications
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
B1
B2
B3
B6
B12
B15
B18
B21
Appendix Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External SCSI Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10BASE-T Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISDN Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard/Mouse or Tablet Port . . . . . . . . . . . . . . . . . . . . .
RS-232 Synchronous/Asynchronous Communications Port .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
C1
C2
C4
C5
C6
C7
C8
C Port Pinouts
D Associated Documents
E Help in Debugging Programs
Examining the Impure Area . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Examining the Machine Check Logout Area . . . . . . . . . . . . . . . .
E1
E2
E3
F Supplementary Information for PTT Network Users

F1
Glossary
Index
Figures
1
11
12
21
22
23
24
25
26
27
28
29
210
211
212
213
214
215
216
vi
Guide to DEC 3000 Model 300 Series AXP

Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Components . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Update Jumper . . . . . . . . . . . . . . . . . . . .
The show device Display . . . . . . . . . . . . . . . . . . . . .
The show config Display . . . . . . . . . . . . . . . . . . . . . .
Configuration Display with Error at Startup . . . . . .
The show mem Display . . . . . . . . . . . . . . . . . . . . . .
Turning Off the System Unit . . . . . . . . . . . . . . . . . .
Removing the System Cover . . . . . . . . . . . . . . . . . .
Attaching the Antistatic Wrist Strap . . . . . . . . . . . .
Power Cable and Connectors . . . . . . . . . . . . . . . . . .
SCSI Cable and Connectors . . . . . . . . . . . . . . . . . . .
Device Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing a Removable-Media Drive . . . . . . . . . . . .
Installing the Shield and Filler Panel . . . . . . . . . . .
Removing the Shield and Filler Panel . . . . . . . . . . .
Cabling the RX26 Drive . . . . . . . . . . . . . . . . . . . . . .
Removing a Disk Drive . . . . . . . . . . . . . . . . . . . . . .
Removing the Mounting Bracket from a Disk Drive
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
xv
12
115
24
26
29
211
216
218
219
219
220
221
223
224
225
226
228
229
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
31
51
61
62
81
B1
B2
B3
B4
B5
B6
C1
F1
Cabling a Drive in Position 1 . . . . . . . . . . . . . . . . .

Cabling a Drive in Position 2 . . . . . . . . . . . . . . . . .
160 MB Memory Configuration . . . . . . . . . . . . . . .
8-Megabyte SIMM . . . . . . . . . . . . . . . . . . . . . . . . .
32-Megabyte Simm . . . . . . . . . . . . . . . . . . . . . . . .
Removing and Installing a Memory Module . . . . . .
Removing and Installing a TURBOchannel Option
Removing the TURBOchannel Filler Plate . . . . . . .
Removing the CPU Module . . . . . . . . . . . . . . . . . .
The Power Supply Cable . . . . . . . . . . . . . . . . . . . .
Removing the Power Supply . . . . . . . . . . . . . . . . .
Reinstalling the Metal Shield . . . . . . . . . . . . . . . . .
Removing the Ethernet ROM . . . . . . . . . . . . . . . .
Removing the System Module . . . . . . . . . . . . . . . .
Replacing the System Cover . . . . . . . . . . . . . . . . . .
Reconnecting the System . . . . . . . . . . . . . . . . . . . .
System Display After Restoring Your System . . . .
External Connections to the System Unit . . . . . . .
The Secure System Jumper . . . . . . . . . . . . . . . . . .
Connecting the Alternate Console to the System . .
Alternate Console Jumper . . . . . . . . . . . . . . . . . . .
Position of Diagnostic Display Lights . . . . . . . . . . .
RX26 Switch Settings . . . . . . . . . . . . . . . . . . . . . .
RZ25 Jumper Settings . . . . . . . . . . . . . . . . . . . . . .
RZ25L Jumper Settings . . . . . . . . . . . . . . . . . . . . .
RZ26L Jumper Settings . . . . . . . . . . . . . . . . . . . . .
Communications Ports . . . . . . . . . . . . . . . . . . . . . .
Ports to Which Warning Label Applies . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
230
231
234
235
235
236
241
242
245
247
248
249
251
253
256
258
259
36
55
63
65
83
B5
B9
B14
B17
B20
B23
C1
F5
vii
Tables
1
11
21
22
23
24
41
42
43
44
45
46
47
48
49
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
51
52
53
54
viii
Telephone Numbers of Digital Support Centers . . . . . . . . .

System Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Elements of the show device Display . . . . . . . . . . . . . . . . .
Elements of the show config Display . . . . . . . . . . . . . . . . .
Elements of the show mem Display . . . . . . . . . . . . . . . . . .
TURBOchannel Options . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supported Keys and Control Characters . . . . . . . . . . . . . .
Parameters/Qualifiers for the boot Command . . . . . . . . . .
Device Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Naming Convention Common to Both Operating Systems
..............................................
Alternate Naming Convention for DEC OSF/1 System . . .
set[env] Command Environment Variables and Values . . .
boot_osflags Command Values . . . . . . . . . . . . . . . . . . . . . .
set diag_section Command Values . . . . . . . . . . . . . . . . . . .
Selecting a Keyboard Language . . . . . . . . . . . . . . . . . . . . .
Environment Variables and Values for the show Command
..............................................
Test Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erase Disk Utility Prompts . . . . . . . . . . . . . . . . . . . . . . . .
Diskette Formatter Utility Prompts . . . . . . . . . . . . . . . . . .
Verify Utility Prompts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASIC Diagnostic Subtests . . . . . . . . . . . . . . . . . . . . . . . . .
FEROM Diagnostic Subtests . . . . . . . . . . . . . . . . . . . . . . .
Memory Diagnostic Subtests . . . . . . . . . . . . . . . . . . . . . . .
NVR Diagnostic Subtests . . . . . . . . . . . . . . . . . . . . . . . . . .
SCC Diagnostic Subtests . . . . . . . . . . . . . . . . . . . . . . . . . .
NI Diagnostic Subtests . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TC Diagnostic Subtests . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCSI Diagnostic Subtests . . . . . . . . . . . . . . . . . . . . . . . . . .
ISDN Diagnostic Subtests . . . . . . . . . . . . . . . . . . . . . . . . .
CXT Diagnostic Subtests . . . . . . . . . . . . . . . . . . . . . . . . . .
Console Command Access . . . . . . . . . . . . . . . . . . . . . . . . .
Steps to Making the System Secure . . . . . . . . . . . . . . . . . .
Entering a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering a Login Command . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
xiv
13
25
27
211
239
44
48
411
.
.
.
.
.
.
.
.
.
.
.
.
412
412
433
439
440
442
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
446
460
462
463
464
466
467
468
469
470
471
474
475
477
478
52
53
53
56
55
61
62
71
72
73
74
75
76
77
81
82
83
A1
A2
A3
A4
A5
B1
B2
B3
B4
C1
C2
C3
C4
C5
C6
D1
D2
D3
D4
F1
F2
F3
F4
Changing a Password . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Alternate Console . . . . . . . . . . . . . . . . . . . . .
Alternate Console/Printer Port Parameters . . . . . . . . . .
Preliminary Troubleshooting of System Problems . . . . .
Troubleshooting Monitor Problems . . . . . . . . . . . . . . . . .
Troubleshooting Mouse/Tablet Problems . . . . . . . . . . . .
Troubleshooting Keyboard Problems . . . . . . . . . . . . . . .
Troubleshooting SCSI Device Problems . . . . . . . . . . . . .
Troubleshooting Network Problems . . . . . . . . . . . . . . . .
Troubleshooting Audio Problems . . . . . . . . . . . . . . . . . .
Console LED Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRU Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Console-Level Problems . . . . . . . . . . . . . . . . . . . . . . . . .
System Unit Dimensions - Desktop . . . . . . . . . . . . . . . .
System Power Specifications . . . . . . . . . . . . . . . . . . . . .
System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .
System Environmental Specifications . . . . . . . . . . . . . .
AcousticsDeclared Values per ISO 9296 and ISO 7779
J5 Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RZ25L Hardware Specifications . . . . . . . . . . . . . . . . . . .
External SCSI Port Pin-outs . . . . . . . . . . . . . . . . . . . . .
10BASE-T Port Pin-outs . . . . . . . . . . . . . . . . . . . . . . . .
ISDN Port Pin-outs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Port Pin-outs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard/Mouse or Tablet Port Pin-outs . . . . . . . . . . . .
Synch/Asynch Communications Port Pin-outs . . . . . . . .
DEC 3000 Model 300 Series AXP System Printed
Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End User Documentation, QAMT4ABGZ . . . . . . . . . .
General OpenVMS AXP Operating System Documents .
Miscellaneous Documents . . . . . . . . . . . . . . . . . . . . . . .
Service Specifications for the System Module . . . . . . . .
Module Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearance and Creepage Distances . . . . . . . . . . . . . . . .
Cables Supported by the Approved Module . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
57
62
64
73
75
76
77
77
78
79
84
86
810
A2
A2
A3
A4
A5
B10
B10
B11
B12
C2
C4
C5
C6
C7
C8
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
D1
D4
D5
D5
F2
F3
F4
F7
ix
Preface
About This
Guide
This guide describes how to:
Remove and replace internal options
Connect external options
Use console commands to run tests and utilities, and to set

and show the value of parameters
Set the password security feature
Connect and use an alternate console
Identify and solve problems
This guide also provides system and option specifications, port

pinouts, a list of associated documents, help in debugging
programs, and information for PTT network users.
Two Methods of
Adding Options
You can add internal options by:
Adding the options yourself.
Having a Digital service representative add them.
You can add external options to your system, by connecting them

to the SCSI port, the ISDN port, the Audio port, and the RS232
asynchronous/synchronous communications port.
If you choose to add internal options yourself, note that additions
typically take about 15 minutes for each option. If you choose
to add external options, note that additions typically take about
5 minutes for each option, although some procedures may take
more or less time.
xi
Conventions in
This Guide
The following conventions are used in this guide:

Convention
Return
Description
A key name is shown enclosed to indicate

that you press the named key on the
keyboard.
UPPERCASE
lowercase
The console program does not distinguish

between uppercase and lowercase
characters in typed user input. All
examples in this guide show user input
in lowercase. All system output is in
uppercase.
show
A word in this typeface indicates a

command that you must enter from the
keyboard at the console prompt (>>>). For
example, boot.
variable
Lowercase italicized letters in commands

indicate a variable value that you must
provide. The value must be an actual
option like a number or logical such as
on/off. For example, >>> set language 3.
A variable may be indicated by angle
brackets < > as in the following help
command example:
>>> he[lp]
Return
Result:
BOOT
HELP ADVANCED
INITIALIZE
SET[ENV] <envar> <value>
SHOW | PRINTENV [<envar>]
TEST
[]
xii
The information contained within these

brackets is optional. The brackets are not
part of the command syntax and should
not be typed.
Convention
Description
{}
The information contained within these

braces is required. The braces are not part
of the command syntax and should not be
typed.
""
Quotation marks indicate a literal string.

A command in lowercase surrounded by
quotes will not convert to uppercase and
will be put on the network as lowercase.
For example, >>> B esa0 -fi "test.sys"
will remain in lowercase letters.
Options/qualifiers are identified by a dash

and indicate that additional information
can be, or in some cases must be, supplied
on the command line. The dash must be
supplied.
WARNING:
Warnings contain information to prevent

personal injury. Read these carefully.
CAUTION:
Cautions provide information to prevent

damage to equipment or software. Read
these carefully.
A number in a circle corresponds to a
number in an illustration.
xiii
Digital Support
Digital Services representatives are available for on-site support

for warranty and service contract customers. If you are not
currently eligible to receive this support but would like to be
eligible, please contact either a Digital Support Center listed in
Table 1, or your local Digital office.
Support
Center Contact
Numbers
Table 1 lists the Digital Support Center contact numbers. If a

number for your area is not listed below, please contact your
local Digital office for assistance.
Table 1 Telephone Numbers of Digital Support Centers
xiv
Country
Telephone Number
United States
1-800-354-9000
Canada
1-800-267-5251
Canada (Quebec)
1-800-267-2603
United Kingdom
[44]25659200
France
[33]92955111
Germany
[49]-(89)-95913218
Australia
009 252-277
Figure 1 is a guide to the DEC 3000 Model 300 Series AXP

documentation.
Figure 1 Guide to DEC 3000 Model 300 Series AXP

Documentation
READ THIS
FIRST:
Setting up
Your System
To use a workstation,
and handle problems.
Adding
Memory
To get the system

set up and running,
and connect to a
network.
Adding a
RemovableMedia Drive
For Digital Services

personnel or customers.
Adding an
Internal Fixed
Disk Drive
MLO-011294
xv
1
Introduction to Your System
Chapter Overview
Introduction
The DEC 3000 Model 300 Series AXP system is a

high-performance, desktop system that uses Digitals
DECchip 21064 RISC-style microprocessor. Your new
DEC 3000 Model 300 Series AXP system is a member of a
family of powerful desktop systems based on the Digital Alpha
AXP architecture. It provides all the advantages of a 64-bit
computing environment and the choice of multiple operating
systems.
In This Chapter
This chapter covers the following topics:
Product Description
Operating Systems
Graphics Capabilities
Audio Capabilities
System Personalization Capabilities
Firmware Update Utility
11
Product Description
Product Description
System
Components
The DEC 3000 Model 300 Series AXP system consists of four
basic components:
System unit
Monitor
Keyboard
Mouse
Figure 11 shows the system and its components.

Figure 11 System Components
MLO-010619
Model 300
Series Features
12
There are four variants of the DEC 3000 Model 300 series of
systems: the Models 300, 300X and 300LX with TURBOchannel
option support, and the Model 300L. Table 11 lists the features
of each system.
Product Description
Table 11 System Features

Feature
Models 300/300X/300LX
Model 300L
Order Number
Operating systems:
DEC OSF/1 AXP;

OpenVMS AXP
Same
CPU speed:
150 Mhz - model 300

125 Mhz - model 300LX
175 Mhz - model 300X
100 Mhz - model 300L
TURBOchannel
options:
Two slots
None
Refer to Chapter 2
Monitor support:
Monochrome 19"
Monochrome 17"
Color 16"
Color 19"
Monochrome 17"
Color 16"
VR319DA/D4
VRM17HA/H4
VRC16HA/H4
VRT19HA/H4
One or two additional

monitors (requires up to
two TURBOchannel HX
options)
Not available
Monitor resolution:
1280 x 1024
1024 x 768
Memory:
8-megabyte standard
inline memory modules
(SIMMs), expandable to 64
megabytes in 16-megabyte
increments.
Same
MS16BA
32-megabyte SIMMs
expandable to 256
megabytes in 64-megabyte
increments.
MS16DA
(continued on next page)
13
Product Description
Table 11 (Cont.) System Features

Feature
Model 300L
Order Number
Graphics:
Integral 8-plane 2D
graphics, 1280 x 1024
HX TURBOchannel option
Integral 8-plane 2D
graphics, 1024 x 768
PMAGBBE/BF
2D TX
TURBOchannel option
(DEC OSF/1 AXP only)
Not available
PMAGBJA/JB
PXG+ 8-plane 3D Z-buffer

Not available
PMAGBDA/DB
PXG+ 24-plane 3D (DEC

OSF/1 AXP only)
Not available
PMAGBEA/EB
8- to 24-plane
upgrade for PXG+
Not available
24-bit Z-buffer upgrade

for 8-plane PXG+
Not available
PMAGHA
ZLX-M1 24-plane
3D Z-buffer
Not available
PMAGCAA
3D Denali graphics
Not available
PEXGAAA/BA
/CA
PMAGGB
14
Product Description

Feature
Model 300L
Order Number
Network
connections:
10BASE-T (twisted-pair)
10 Mb/s Ethernet port
Same
AUI or ThinWire
(10base2) connection using
a Digital-recommended
adapter
Industry-standard ISDN
port for voice and data
Secure system
feature:
Additional system security

for limited access to
console functions
Same
Audio technology:
Telephone quality audio

input/ output, including a
built-in speaker. Headset
available with some
models.
Same
15
Product Description

Feature
Model 300L
Order Number
External SCSI-II
port:
One on-board 5 MB/s SCSI

channel for both internal
and external devices (up
to two internal and five
external devices)
Same
Optional dual SCSI

TURBOchannel module
Not available
PMAZCAA
Communications
port:
25-pin synchronous/
asynchronous connection
to a printer, plotter,
modem, or console
terminal.
Same
Battery backup
clock:
Battery-run backup
internal clocking
system for synchronous
operations.
Same
Internal devices:
Two 3-inch RZxx fixed

disk drives: RZ25, RZ25L,
RZ26, RZ26L or optional
RZ28
Same
RZ25EP
RZ25LEP
RZ26EP
RZ26LEP
RZ28EP
or
One 3-inch RZxx fixed
disk drive and one 3-inch
RX26 removable-media
drive
Future Options
16
RX26FB
Additional options for your system may be available at a later

time.
Operating Systems
Operating Systems
A Choice of
Operating
Systems
Digitals Alpha AXP architecture supports multiple operating

systems for your DEC 3000 Model 300 Series AXP system.
This section gives a brief description of the operating systems
currently available for this product:
OpenVMS AXP
DEC OSF/1 AXP
Information about installation and operation of each operating

system is provided in system-specific software documentation.
OpenVMS AXP
The OpenVMS AXP operating system:
Is a general-purpose, multiuser operating system that can be

used in many different environments for a wide variety of
applications.
Promotes ease-of-use and improved programming

productivity, and facilitates system management.
Offers a combination of commercial strength and open

system benefits, including the following:
integrated networking
system security
distributed computing
windowing capabilities
DEC OSF/1
AXP
Supports a large number of industry standards that facilitate

application portability and interoperability.
The DEC OSF/1 AXP operating system complies with the OSF
Application Environment Specification (AES), which specifies
the interface to support applications that run on a variety of
hardware platforms.
17
Operating Systems
The DEC OSF/1 AXP operating system:
Is Digital Equipment Corporations implementation of

the Open Software Foundation (OSF) operating system
components and Motif graphical user interface and
programming environment.
Complies with standards and industry specifications,

including FIPS 151-1, POSIX (IEEE Std. 1003.1-1988),
XPG3 BASE branding, XTI, and AT&T System V Interface
Definition (SVID) Issue 2 (Base System and Kernel
Extensions).
Is an advanced kernel architecture based on Carnegie Mellon

Universitys Mach V2.5 kernel design with components from
Berkeley Software Distribution 4.3 (BSD) and other sources.
DEC OSF/1 AXP provides numerous features to assist
application programmers in developing applications that use
shared libraries, multithread support, and memory mapped
files.
Factory
Installed
Software
18
If there is a yellow sticker over the power connector on the

back of your system unit, your operating system is already
installed on an internal fixed disk. Depending on which
operating system you ordered, your wrokstation will start with
the OpenVMS AXP Factory Installed Software (FIS) procedure,
or the DEC OSF/1 AXP Initialization Transition (IT) program.
Refer to your factory-installed software instructions for:
Startup procedures
Examples of startup screens
System prompts
Password information
Login information
The Model 300L
System
All DEC 3000 Model 300 Series AXP systems are shipped with
an integral, high-performance, accelerated 2-D, 8-plane, color
graphics frame buffer on the system module. However, the
Model 300L does not support additional graphics heads; that is,
you cannot connect more than one monitor to the system.
The Model
300/300X/300LX
Systems
Additional graphics capabilities are supported on the DEC 3000

Model 300 Series AXP systems; support is operating-system
specific.
OpenVMS Operating System

If your DEC 3000 Model 300 Series AXP system is running
the OpenVMS AXP operating system, you can add one or two
two-dimensional (2D) HX graphics options in TURBOchannel
slots 0 and/or 1. This HX option provides additional 8-plane,
accelerated 2D graphics and windowing operations. You can
add two HX options and two additional monitors to expand
the display area. Information about setting up your system
to use more than one monitor is provided in the OpenVMS
Alpha Version 1.5 Upgrade and Installation Manual.)
19
DEC OSF/1 Operating System

If your DEC 3000 Model 300 Series AXP system is running
the DEC OSF/1 AXP operating system, version 1.3B or
later, the two-dimensional (2D) HX graphics option, the
two-dimensional (2D) TX graphics option, the 2D/3D ZLX
graphics options, or the 3D HX+ graphics option can be
installed in a TURBOchannel slot.
Adding either the HX option (for DEC OSF/1 AXP and
OpenVMS AXP), or adding either the HX+ or the TX option
(for DEC OSF/1 AXP only), allows you to expand the display
area. The TX option provides 8-bit and 24-bit accelerated
2D graphics, windowing operations, and a hardware cursor.
The HX+ option provides 8-bit and 24-bit accelerated 3D
graphics, windowing operations, and a hardware cursor.
Information about setting up your system to use more than
one monitor is provided in the DEC OSF/1 Guide to System
Administration.
Installation
Information
110
For information about installing graphics options in the Model

300/300X/300LX systems, see Chapter 2.

ISDN Not Yet
Available
Though your DEC 3000 Model 300 Series AXP system can
provide ISDN capabilities, it is not as yet agency approved and
available for your DEC 3000 Model 300 Series AXP system.
When your system is shipped, a foam block covers the ISDN port
on the back of the system unit.
Once agency approval of ISDN for the DEC 3000 Model 300
Series AXP systems is granted, you will be contacted by your
Digital sales representative to inform you of ISDN certification.
When you are ready to install ISDN hardware, you must request
your Digital service representative install the required hardware.
The following information explains the ISDN capabilities for
your DEC 3000 Model 300 Series AXP system pending license
approval.
Australian ISDN
Connections
The ISDN interface in this equipment has not completed

Australian ISDN network connection certification testing and
as such does not have an AUSTEL permit for connection. In
Australia, it is an offense to connect nonpermitted devices to a
public telecommunications network and may attract a fine of up
to $12,000.
ISDN
Capabilities
ISDN is a digital telecommunications network, providing

connectivity for voice and data applications.
Your DEC 3000 Model 300 Series AXP system includes an ISDN
Basic Rate S/T interface, which includes:
Use of ISDN B
Channels
Two 64 kilobits per second B channels for voice and data

transmission
One 16 kilobits per second D channel for signaling and

control
The B channels can be used for digitized voice, circuit-switched

data at up to 64 kilobits per second, or packet-switched data
transmission.
111
Use of ISDN D
Channels
The D channel uses a protocol standardized by the International

Telegraph and Telephone Consultative Committee (CCITT) for
setting up these D-Channel connections. The D channel can also
be used for low-speed packet transmission.
Audio Capabilities
Audio Feature
The DEC 3000 Model 300 Series AXP system features telephonequality audio input and output capabilities, including a built-in
speaker.
You can attach a microphone, headphone, handset, headset,
or externally-powered speakers to the audio port. Normally,
the RS232 audio port is used in asynchronous mode. However,
support for X.25 synchronous communications is available, but is
operating-system-dependent.
The port pinouts for the audio jack on the back of the system
unit are provided in Appendix C. Chapter 4 describes ISDN tests
that you can issue from console mode: for example, to repeat,
record and playback audio messages.
DECsound
Application
The DECsound application, shipped with your system as part

of the DECwindows Motif for OpenVMS AXP software, is an
easy-to-use software application that lets you play back recorded
messages, record audio messages, mail recorded messages, and
include recorded messages in compound documents.
Audio
Conferencing
Software
Multimedia Services software and the DECspin audio

conferencing software are also shipped with your system as
part of the DEC OSF/1 software. These free applications let
you take advantage of the voice-quality base audio on your
system. The audio headset (provided in the parts kit with some
models) is for you to use in the quiet of your office with these
new applications. See the information sheet provided with the
headset for instructions on how to start the applications.
112

Firmware
Parameters
Your system firmware includes commands and parameters that

you can change to suit your specific needs. You may change the
default settings for these parameters from console mode (>>>) by
entering the set command followed by the parameter you want
to change, as described in the next table.
To change this...
Use this command...
The action the console takes after a halt
set auto_action
set bootdef_dev
set diag_quick
The default boot device

The default diagnostic startup mode
Refer to Chapter 4 for the format and available settings for these
parameters.
Before You
Change
Parameters
Do not change any parameters without fully understanding the

effect that the change may have on your workstation. If you are
not sure about changing parameters, ask your system manager
for assistance, or your Digital service representative.
113

Purpose
Digital Equipment Corporation distributes new Firmware

Update utility software whenever there are any changes to the
console firmware. The utility provides new firmware for the flash
ROM (read-only memory) in your system, including the console
program and diagnostic testing capabilities.
Note
Refer to the release notes you receive with the software
update for an explanation of how to use the Firmware
Update Utility software.
Write-Protecting
the Flash ROM
For your convenience, your system is shipped from the factory

with the flash ROM write jumper, labeled W1 on the system
module, in the write-enabled position. Thus, there is no need
to remove the system unit cover and get inside the system unit.
You can update your console firmware with the latest version
using the release notes.
To write-protect the flash ROM so that it cannot be overwritten:
1. Open the system unit cover.
Caution
To avoid possible product damage, refer to Chapter 2 for
instructions on how to power off the system, open, and
work inside your system unit.
2. Locate the W1 jumper shown in Figure 12.

The default write-enabled position of the jumper is on pins 2
and 3.
114
Figure 12 Firmware Update Jumper
MLO-010745
Enabled
Disabled
3. Write-protect the flash ROM by moving the jumper to pins
1 and 2 (the disabled position), using tweezers or another
small tool.
4. Replace the system unit cover.
Once this is done, future firmware updates will require
repositioning the jumper.
115
2
Adding, Removing, and Replacing Internal
Options
Chapter Overview
In This Chapter
When you receive your system from Digital, it may be configured

with the internal devices specified in your order. At a later time,
however, you may wish to add another internal option, or remove
and replace one option with a different option.
This chapter provides the following information:
Recording Information Before Making Changes
Understanding SCSI IDs
Preparing Your System
Identifying and Locating Options
Removing and Installing a Removable-Media Drive
Removing and Installing a Fixed Disk Drive
Removing and Installing a Memory Module
Removing and Installing a TURBOchannel Option (For

Models 300/300X/300LX Systems)
Removing and Installing the CPU Module
Removing and Installing the Power Supply
Removing and Installing the System Module
Restoring the System
21
Chapter Overview
Required Tools
Be sure you have a Phillips screwdriver before you attempt to

remove the system unit cover or install options. You may also
need a flat-head screwdriver to remove some of the cables from
the back of the system unit.
Two Methods
for Adding
Options
There are two methods of adding internal options:
Add the options yourself.
Have a Digital service representative add them.
If you choose to add options yourself, note that additions

typically take about 15 minutes for each option, although some
procedures may take more or less time.
CAUTION:
Possible
Module
Damage
Improper installation of an optional drive or module could lead

to damage and failure of both the new drive or module and other
system components. Your DEC 3000 Model 300 Series AXP
warranty may not cover such a failure.
Device
Verification
Be sure to refer to the operating system software product

description (SPD) to verify that all installed devices are
compatible with the operating system you are using.
22

Diagnostic
Displays
Before you install any options, you should be familiar with your
DEC 3000 Model 300 Series AXP system and the following
diagnostic displays:
System startup messages
The displays resulting from the following console mode (>>>)

commands:
show device to display the names and status of devices in

your system. Device is a general name for any hardware
unit capable of receiving, storing, or transmitting data.
show config to display the status of the devices in your
system
show mem to display the amount of memory installed

These show commands are described in the next few sections.
The show
device
Command
Enter the show device command as follows:

>>> show device
Return
The show device command displays the status of each SCSI

device and network interconnect that is recognized by the
system. Record the displayed information for later reference
(of particular importance is the information in the BOOTDEV,
ADDR and DEVNAM columns). After adding or replacing a
drive, you can then compare the new system configuration with
the previous one to verify that all drives were installed correctly.
If an installed drive is not listed in the display, it either is not
installed correctly or may be damaged.
The following occurs when the show device command is issued:
The system issues the inquiry command to obtain device

types and device names
The system spins up the disks
The device information is displayed
23
The following information is displayed:

ID, controller, Logical Unit Number (LUN)
Device name
Device type
Device capacity
Removable or fixed media
Write protection information for each disk
Firmware revision
The show
device Display
Figure 21 shows an example of a show device display (the

numbers are for reference only).
Figure 21 The show device Display
BOOTDEV
------ESA0
DKA300
DKA500
..HOSTID..
>>>
24
ADDR
DEVTYPE NUMBYTES
---------- -------08-00-2B-2F-F8-E6 , TENBT
A/3/0
DISK
535MB
A/5/0
DISK
......
A/7
INITR
RM/FX WP DEVNAM REV

----- -- ------ --FX
RM
RZ25L
RX26
0900
0068
Table 21 defines the columns of the show device display.

Table 21 Elements of the show device Display
Element
Description
BOOTDEV
Console boot name for a device.
ADDR
The Ethernet hardware address of each

device. 08-00-2B-2F-F8-E6 is an example
of the system hardware Ethernet address.
The SCSI ID address setting of each
device, A/3/0 is an example: where A
identifies the controller unit, 3 identifies
the address setting, and 0 identifies the
logical unit number (LUN).
DEVTYPE
The type of device in the system.
NUMBYTES
The capacity of this device.
RM/FX
Specific device in this system: a

removable-media (RM) or a fixed-disk
(FX) device.
WP
Status of the drive: write-protected or not

write-protected.
DEVNAM
The device name of the installed device.
REV
The microcode revision number of the

installed device.
25
Enter the show config command as follows:
The show
config
Command
>>> show config
Return
The show config command displays the following information:
The system model number
Revision number of the PAL (privileged architecture library)

chip
Name or mnemonic and status of the device
Record this information for later reference. After adding or

replacing option modules, you can compare the new system
configuration with the previous one to verify that all options are
present and functioning correctly.
Figure 22 shows an example of a show config display.
Table 22 defines the elements of the display.
Figure 22 The show config Display
DEC 3000 M300

Digital Equipment Corporation
VPP PAL X5.25-80800101/OSF PAL X1.14-80800201 - Built on 2-OCT-1993
TCINFO
------
DEVNAM
-------CPU
DEVSTAT
-------OK KN16-AA - Vx.x-Syyy-Izzz- sx.x - DECchip 21064 P3.0
ASIC
MEM
FEROM
OK
OK
OK
CXT
OK
NVR
SCC
NI
ISDN
OK
OK
OK
OK
SCSI
OK
6
5
4
>>>
26
12:47:55.09
Table 22 explains the elements in Figure 22.

Table 22 Elements of the show config Display
Element
Description
The system model number.

The revision number of the VPP PAL (privileged
architecture library) code: where Xn.nn is for
OpenVMS AXP or for the DEC OSF/1 AXP PAL code,
and the date on which it was released.
The physical addresses for baseboard devices, as
follows:
Slots 0 and 1 are for TURBOchannel
devices (Models 300/300X/300LX only). If a
TURBOchannel module requires both slots 0
and 1, only slot 0 is listed in the display.
Slots 2 and 3 are reserved.
Slot 4 is for a SCSI device.
Slot 5 is for I/O control.
Slot 6 is for the CXT (integral 2D accelerated
graphics module).
Slot 7 is for the system CSRs.
Device name or mnemonic.
The status of the device:
KN16-AA identifies the CPU type.
Vx.x identifies the system revision.
Syyy identifies the system ROM edit revision.
Izzz identifies the I/O ROM edit revision.
sx.x identifies the serial ROM edit revision.
DECchip 21064 P3.0 identifies the AXP chip
revision.
OK means that the device is installed correctly and
diagnosed to be OK.
A blank means there is no test for this device.
27
System
Configuration
Errors
Two question marks (??) next to a component name in the

DEVSTAT column indicate a problem with that component. If
you normally use the set diag_quick on command to define
your diagnostic startup mode, the error message consists of the
question marks alone. Refer to Chapter 8 for an explanation of
the error line.
To display the error message, you must enter the following
command:
>>>show error
Example:
>>> show error
Return
?? 004 SCC 0x0060

?T-ERR-SCC-MOUSE - 0 char rcvd
Refer to Chapter 4 for an explanation of the show error
command.
If you use the set diag_quick off command to define your
diagnostic startup mode (a full startup sequence occurs), then
you will see two question marks in the display; see Figure 23.
Note any field replaceable unit (FRU) number and error number.
An FRU is a replaceable drive or module. See Chapter 8 for
additional information about error messages and FRU codes.
28
Figure 23 Configuration Display with Error at Startup

DEC 3000 Model 300
VPP PAL X5.25-80800101/OSF PAL X0.14-80800201 - Built on 2-OCT-1993 12:47:55.09
TCINFO
------
DEVNAM
-----CPU
DEVSTAT
-------OK KN16-AA - Vx.x-Syyy-Izzz - sx.x - DECchip 21064 3.0
150
ASIC
MEM
OK
OK 32MB
6
CXT
OK
5
NVR
SCC
NI
ISDN
OK
?? 003 0050 ptr(0) = Not Present keybd(2) = Not Present
OK Ethernet Address: 08-00-2B-2F-F8-E6, TENBT
OK
4
SCSI
OK
>>>
-------------------------------------------------------------------------System power up tests detected error(s).
See your system documentation for more information.
*** NO KBD - Switching to Alternate Console ***
To interpret this error message, refer to Chapter 8

of this guide for a list of FRU codes and the
DEC 3000 Model 300 Series AXP Service Guide for a detailed
explanation of error codes.
29
What to
Do About a
Configuration
Error
The show mem

Command
Refer to the following table to resolve a configuration error:

If you...
Then...
Are not comfortable

diagnosing technical
errors
Contact your Digital service

representative.
Are comfortable
diagnosing technical
errors
Refer to Chapter 4 for a description

of console commands, Chapter 8
for FRU codes, and the DEC 3000
Model 300 Series AXP Service
Guide for more information.
The show mem command displays the following information:
Bank number
Memory size for each bank
Start address for each bank
Record this information for later reference. After adding or

replacing memory, you can compare the new system configuration
with the previous one to verify that all options are present and
functioning correctly.
Enter the show mem command as follows:
>>> show mem
210
Return
The show mem

Display
Figure 24 shows an example of a show mem display. (The

numbers are for reference only.)
Figure 24 The show mem Display
BANK #
-----0
1
2
3
4
5
6
7
MEMORY_SIZE
----------008 Mbytes
008 Mbytes
008 Mbytes
008 Mbytes
000 Mbytes
000 Mbytes
000 Mbytes
000 Mbytes
START_ADDRESS
-------------0x00000000
0x00800000
0x01000000
0x01800000
0x00000000
0x00000000
0x00000000
0x00000000
>>>
Table 23 defines each element of the show mem display.
Table 23 Elements of the show mem Display
Element
Description
BANK #
The bank numbers indicate the

position of each memory board.
MEMORY_SIZE
The memory size is the total

amount of memory installed in
each bank. In this example, there
are eight megabytes of memory in
banks 0, 1, 2, and 3; none in the
remaining banks.
START_ADDRESS
The starting address is the location

number of each memory bank.
211

Overview
Before you remove an internal device and install another device,

you should note the following information about devices and
understand SCSI IDs.
Digital RX26
Drive
Your system may arrive configured with an RX26 removable

media drive. The hardware specifications and device-specific
SCSI ID information for this drive are included in Appendix B of
this document.
If you plan to add an RX26 removable media drive, refer to DEC
3000 Model 300 Series AXP Adding a Removable-Media Drive
(part number EKPELAFIC), shipped with the drive.
RZ25, RZ25L,
RZ26 or RZ26L
Drives
Your system may arrive configured with an RZ25, RZ25L, RZ26

or RZ26L fixed disk drive. The hardware specifications and
device-specific SCSI ID information for these drives are included
in Appendix B of this document.
If you plan to add an RZ25, RZ25L, RZ26, RZ26L or the
optional RZ28 fixed disk drive, refer to DEC 3000 Model 300
Series AXP Adding an Internal Fixed Disk Drive (part number
EKPELADIC), shipped with each additional drive ordered.
Adding an
External Option
If you plan to add a Digital manufactured compact disc drive,

tape drive, or expansion box, refer to the documentation that
accompanies that option for the proper setting of SCSI addresses
for the device. See Appendix D for a listing of external option
documentation.
If you plan to add a device that is not manufactured by Digital,
refer to the documentation accompanying the device for SCSI ID
address information.
212
Brief
Introduction to
SCSI IDs
For proper communication between your system and all the

devices installed in the system unit, each device must have a
unique SCSI address setting (ID). SCSI settings are determined
by the position of the electrical switches or jumpers located on
the back or side of the device. Switches can be either up or
down; jumpers can be either attached or removed.
If you are replacing a device, be sure the SCSI ID setting on the
new device is unique. Only one SCSI ID (06) is allowed per
device. The SCSI ID 7 is reserved for the SCSI controller.
If you order a new drive separately from the system, you will
receive an installation card. Refer to this card for the exact
location of the switches or jumpers on the drive you order.
A replacement drive is often set to the same address as the drive
it replaces. Use the show device command on the replacement
drive to confirm its address.

Overview
Before you install or remove any internal option, you must take
the following steps to prevent loss of data or damage due to
static discharge. Refer to the appropriate section of this chapter
for details of each action.
Step
Action
Back up your files.
Shut down all software following the instructions in your

software documentation.
At the console prompt (>>>), enter the show mem,

show device, and show config commands. Record the
displayed information.
At the console prompt (>>>), enter the set auto_action
halt command.
213
Step
Action
Turn off the monitor and all peripheral devices such as

printers, modems and expansion boxes.
Turn off the system unit.

Warning
Before you unplug the power cord and open the system
unit, wait about one minute. This allows time for the
power supply capacitors to safely discharge.
Shut Down
Networked
Systems
Shut Down
Operating
Systems
214
Remove all cables, loopbacks, terminators and power

cords from the back of the system unit and monitor.
Wait a few minutes for the monitor to discharge.
Move the monitor away from the system unit (this

requires two people).
10
Remove the system unit cover.
11
Attach the antistatic wrist strap.
Procedures for shutting down your software vary depending on

how your system is networked.
If you are
See your
Networked, or part of a cluster
System manager
Not networked, nor part of a cluster
Software documentation
Not sure if you are part of a network
System manager
For information on how to shut down your operating system,

refer to your operating system documentation. These manuals
and their order numbers are listed in Appendix D.
Shutting down your system may require knowledge of file back

up and operating system shutdown procedures. The following
privileges may be required:
For the OpenVMS AXP operating system, the shutdown

procedure usually requires certain software privileges.
For the DEC OSF/1 AXP operating system, you may require
superuser privileges to shutdown the system.
If you do not have the required system privileges, ask your

system manager for assistance.
Operating
System
Shutdown Command
Documentation Titles
OpenVMS
AXP
@sys$system:shutdown
System Management,
Vol. 1A, Guide to Starting
Up and Shutting Down the
System
DEC OSF/1
AXP
shutdown -h now
Guide to System
Administration
Note
Typing shutdown -r now or reboot at the console prompt
(>>>) reboots your system.
Turning Off
Equipment:
Task Overview
Shutting down the hardware involves the following steps:

Step
Action
Turn off (O) all expansion boxes.
Turn off (O) all peripheral devices (such as printers).
Turn off (O) the monitor. (Turning off the system does not
automatically turn off the monitor).
Turn off (O) the system by pressing the On/Off switch

on the back of the system unit to the off (O) position, as
shown in Figure 25.
215
Figure 25 Turning Off the System Unit
ISD
MLO-009747
CAUTION:
Before
Disconnecting
a Monitor
After you turn off the system and before you disconnect the
power cord from the monitor and system unit, wait about one
minute to allow time for the power supply capacitors to safely
discharge.
To disconnect the monitor:
Step
Action
Disconnect the power cords from the monitor and system

unit.
Disconnect the monitor video cable from the rear of the

monitor and system unit.
Move the monitor away from the top of the system unit.
Warning
The monitor can weigh up to 75 lbs. (34 kg). To avoid
possible injury, two people are required to move the
monitor.
216
Remove the
System Unit
Cover
To remove the system unit cover, refer to Figure 26 and follow

these steps:
Step
Action
Remove the two Phillips screws on the right and left back
corners of the system unit cover .
Place the system unit so that the back edge extends over
the edge of your table or desk.
Place your thumbs on the two black caps

on the back of
the system unit, and at the same time, place your fingers
under the covers bottom edge. Press down with your
thumbs while you press up against the covers edge with
your fingers to lift the cover.
Note
A significant amount of pressure is required to lift the
cover. You may want to cushion your fingers.
Pivot the cover on the tabs that run along the system
units front edge.
Pull the system unit cover up and away until it releases

from the tabs.
Place the cover safely aside.
217
Figure 26 Removing the System Cover
2
0
ISD
MLO-010097
WARNING:
Thermal
Problems
Do not run the system for an extended period of time (15

minutes) with the cover removed. Prolonged use of the system
without the cover may cause thermal problems.
CAUTION:
Static
Discharge
Do not touch anything inside the system unit until you attach
the antistatic wrist strap included with your system or option
shipment. Always use this strap when you work inside the
system unit to avoid damage to internal devices from static
discharge. Digital also recommends that you use an antistatic
mat.
To attach the antistatic wrist strap, shown in Figure 27, follow
the steps printed on the envelope containing the strap. Save this
envelope for storing the strap.
218
Figure 27 Attaching the Antistatic Wrist Strap
MLO-010098
Identify the
Internal Power
Cable
Each connector on the internal power cable must be connected to

the corresponding power port on the back of each drive.
The internal power cable and connectors are shown in
Figure 28.
Figure 28 Power Cable and Connectors
MLO-009791
Connects to the system module.

Connects to a fixed disk drive, if any.
Connects to a second fixed disk drive or removable-media
drive, if any.
Connects to the removable-media drive only.
219
Identify the
Internal SCSI
Cable
Each connector on the internal SCSI cable must be connected

to the SCSI port on each drive. The internal SCSI cable and
connectors are shown in Figure 29.
Figure 29 SCSI Cable and Connectors
1
2
3
4
MLO-009792
Connects to the system SCSI bus.

Connects to a fixed disk drive in position 1, if any.
Connects to a fixed disk drive or a removable-media drive in
position 2, if any.
Is a SCSI bus terminator.
220

Figure 210 shows the location of memory modules, fixed disk
and removable media devices, and TURBOchannel modules (if
any) in the DEC 3000 Model 300 Series AXP systems.
Figure 210 Device Positions
2
5
MLO-009798
Power supply
CPU module with heat sink
TURBOchannel option module installed in slot 0 (slot 1 is
shown empty)
Memory modules
Device position 2
Device position 1, with a fixed disk installed
221

Antistatic
Precautions
Do not remove or install any internal option without attaching

the antistatic wrist strap to your wrist and the system. Refer to
the caution statement associated with Figure 27.
Remove a
Removable-Media
Drive
To remove a removable-media drive from position 2, perform the

following steps:
222
Step
Action
Be sure all system preparation tasks are complete. Refer

to Preparing Your System for additional information.
Record, for later use, the SCSI ID setting of the drive

you remove. Use the show device command (Chapter 4)
before you remove the device.
Unlock the drive from the base of the system unit by

releasing the latch on the left side of the drive. (See
Figure 211.)
Disconnect the internal power and SCSI cables.
Lift up and slide the drive to the left. (See Figure 211.)
Insert the filler panel and shield, as described in the

section entitled Install the Filler Panel and Metal Shield
later in this chapter.
Figure 211 Removing a Removable-Media Drive
MLO-010237
Removable-Media
Drive SCSI
Switch Settings
The setting of the SCSI switches on the removable-media drive

enables the system to recognize the drive. Normally, the SCSI
address for removable-media drives should be preset to a SCSI
ID of 5.
However, if your drive is not preset to SCSI ID of 5, you need to
change it only if the drives setting is already taken by another
device installed in your system.
If you do change the setting, use a small pointed instrument
(such as the tip of a ballpoint pen) to move the switches. Do not
use a pencil; graphite particles can damage the switches. Refer
to Appendix B for an illustration of SCSI ID settings.
223
Install the Filler

Panel and Metal
Shield
After you remove a removable-media drive, look for a plastic

filler panel and metal shield that came in your shipment (see
Figure 212). To fill in the space that the front of the drive
occupied:
Step
Action
Insert the filler panel

from the outside into the
open slot on the system unit cover bezel, as shown in
Figure 212.
Insert the metal shield

from the inside into the
open slot on the system unit cover bezel, as shown in
Figure 212.
Figure 212 Installing the Shield and Filler Panel
MLO-010570
Remove the
Filler Panel and
Metal Shield
224
If you did not order a removable-media drive from the factory

when you placed your order with Digital, and are installing one
now, you must first remove the plastic filler panel and metal
shield from the front bezel on the system unit cover.
To remove these items:

Step
Action
Release the filler panel from the metal shield by gently

pressing on the filler panel tabs and pushing outward.
in Figure 213.
See
Store the shield and filler panel for future use.
Figure 213 Removing the Shield and Filler Panel
MLO-010273
Connect the
Drive Cables
To cable the drive, hold it outside the system unit before you
install it, follow these steps, and refer to Figure 214:
Step
Action
Connect the large connector

on the power cable to the
power port on the back of the RX26 drive.
Connect the small connector

on the power cable to the
smaller power port on the back of the drive.
225
Step
Action
Connect the internal SCSI cable with the key facing up

to the SCSI port on the back of the drive. The power
cable must be under the SCSI cable.
Tuck the SCSI terminator , located at the end of the

SCSI cable, in the mounting bracket under the RX26
drive.
Figure 214 Cabling the RX26 Drive
1
2
4
MLO-009745
Install a
Removable-Media
Drive
226
To install a removable-media drive, reverse the steps in the

removal procedure as follows:
Step
Action
Record the SCSI ID setting for future use. Refer to

Chapter 4, the show device command.
Be sure all system preparation tasks are complete. See

the section entitled Preparing Your System.
Be sure the cables are all connected.
Format a
Diskette
Step
Action
Insert the mounting bracket tabs on the right side of the

drive into the slots on the base of the system unit.
Press down on the drive.
Lock the drive in place, by sliding the latch back. (See

Figure 211).
After you have installed a removable-media drive, you may

wish to format a diskette before you use it. You do this with
the Diskette Formatter Utility. Refer to Diskette Formatter
Utility Example in Chapter 4 for a description and example of
the test scsi format command that runs this utility.

Antistatic
Precautions

the section entitled CAUTION: Static Discharge.
Device
Configuration
Your system may arrive configured with either an RZ25, RZ25L,

RZ26 or RZ26L fixed disk drive. The installation instructions
in the following sections picture an RZ25 or RZ26 drive; the
instructions also apply to the RZ25L, RZ26L and RZ28 fixed disk
drives.
Remove a
Fixed Disk
To remove a fixed disk drive, perform the following steps and

refer to Figure 215:
Step
Action

to the section entitled Preparing Your System for more
information.
227
Step
Action
Unlock the drive by pushing the lock tab back, as shown

in Figure 215.
Disconnect the internal power and SCSI cables from the

back of the drive.
Tilt the drive to the left and lift it out of the system.
Figure 215 Removing a Disk Drive
MLO-010244
228
Note
If you are replacing a drive with a third-party drive,
remove the mounting bracket from the drive, as shown in
Figure 216.
Figure 216 shows the removal of the mounting bracket from

a fixed disk drive. Remember, this is necessary only if you are
replacing the drive with a third-party drive, or if you need to
gain access to the SCSI ID settings.
Figure 216 Removing the Mounting Bracket from a Disk Drive
MLO-010240
229
Cabling for
Drive in
Position 1
To cable the drive that you are installing in position 1, follow

these steps and refer to Figure 217:
Step
Action
Connect the large power connector

on the power cable
to the power port on the back of the RZxx drive.
Connect the internal SCSI cable

to the back of the disk
drive. Be sure the key (the notch in the center of the
cable connector) is facing up. The power cable
must be
under the SCSI cable.
Lay the terminator, located at the end of the SCSI cable,

and the remaining length of power cable in the empty
position 2.
Figure 217 Cabling a Drive in Position 1
3
MLO-010660
230
Cabling for
Drive in
Position 2
To cable the drive that you are installing in position 2, follow

these steps and refer to Figure 218:
Step
Action
Connect the large power connector

on the power cable
to the power port on the back of the RZxx drive.
Connect the internal SCSI cable

up, to the back of the disk drive.
Tuck the SCSI terminator , located at the end of the

SCSI cable, in the mounting bracket under the RZxx drive
in device position 2.
, with the key facing
Figure 218 Cabling a Drive in Position 2
3
MLO-010242
231
Install a Disk
Drive
Fixed Disk
Drive SCSI
Jumper
Settings
To install a fixed disk drive, reverse the steps in the removal

procedure, as follows:
Step
Action
Record the SCSI ID setting for future use. Refer to the

next section and Chapter 4, the show device command.
Be sure all system preparation tasks are complete

before opening the system. Refer to the section entitled
Preparing Your System.
Be sure all cables are connected.
Insert the mounting bracket tabs on the left of the

drive into the slots on the base of the system unit. (See
Figure 215.)
Press down on the drive.
Lock the disk drive in place by pulling the lock tab

forward.
When a fixed disk drive arrives from the factory, all SCSI
jumpers may be attached to prevent loss during shipment.
Digitals recommended setting for a fixed disk drive is 1, 2, or 3.
However, if the drive is preset to a SCSI ID other than 1, 2, or
3, you need not change it unless that setting is already taken by
another device installed in your system.
To change the setting, choose one that is not in use, and carefully
move the jumpers using tweezers or another small tool. If you
remove any jumpers, save them, you may need them later. Refer
to Appendix B for the device you are installing.
Verify Disk
Blocks
After you have installed a disk, you may wish to verify that
all blocks on that disk can be read. You do this using the Disk
Verify utility. Refer to Chapter 4 for a description and example
of the test scsi verify command that runs this utility.
Erase a Fixed
Disk
You may also need to erase a fixed disk if you are installing a
previously-used one. Do this using the Erase Disk Utility. Refer
to Chapter 4 for a description and example of the test scsi
erase command that runs this utility.
232

Antistatic
Precautions

Memory Module
Introduction
A memory module is known as a Single Inline Memory Module

(SIMM). Two types of memory modules are supported on
the DEC 3000 Model 300 Series AXP system, each type has
components on both sides of the module:
An 8-megabyte memory module (part number MS16BA)

that allows from 16 to 64 megabytes of memory to be added
in 16-megabyte increments
A 32-megabyte memory module (part number MS16DA)

that allows from 64 to 256 megabytes of memory to be added
in 64-megabyte increments
The two memory module types may be mixed in your memory

configuration, as long as the memory configuration guidelines
are followed.
Your DEC 3000 Model 300 Series AXP system module includes
eight memory module connectors.
Note
Always handle memory modules by their edges to avoid
electrical damage and contamination of the module pins
and connectors.
It may be necessary to remove a device before you add
the last SIMM.
233
Memory
Configuration
Rules
When mixing 8 and 32megabyte SIMMs, follow these rules:
Always add the 32megabyte SIMMs first.
Add 32megabyte SIMMs in pairs, 64 to 256 megabytes in

total.
Add 8megabyte SIMMs in pairs, 16 to 64 megabytes in

total.
Always add SIMMs in pairs, no individual modules, 2, 4, 6 or

8 SIMMs in the system.
Add SIMMs starting at slot 0 (see Figure 219).
No empty slots between pairs of SIMMs.
The following example is provided for information only. For a

system that requires 160 megabytes of memory, follow these
steps:
1. Add one 32-megabyte SIMM (MS16-DA) to slots 0, 1, 2, and
3, for a total of 128 megabytes of memory.
2. Add one 8-megabyte SIMM (MS16-BA) to slots 4, 5, 6, and 7,
for a total of 32 megabytes of memory.
Figure 219 160 MB Memory Configuration
MS16-DA
Slot
0
MS16-DA
MS16-DA
MS16-DA
MS16-BA
MS16-BA
MS16-BA
MS16-BA
7
MLO-010947
234
Adding 8MB
SIMMs
To increase your systems memory capacity from a minimum of

32 megabytes to 48 or 64 megabytes, add two or four 8-megabyte
SIMMs. The SIMMs are identified by counting ten chips on the
top row
and four chips on the bottom row
in Figure 220.
There are fourteen chips on one side of the module, but only 10
chips on the other side of the module. Note that the 8 megabyte
chips on the top row are smaller than the 32-megabyte chips
shown in Figure 221.
Figure 220 8-Megabyte SIMM
1
2
MLO-010945
Adding 32MB
SIMMs
To increase your systems memory capacity from a minimum

of 64 megabytes to 128 or 256 megabytes, add four or eight
32-megabyte SIMMs. The SIMMs are identified by counting
eight chips on the top row , and four chips on the bottom row
in Figure 221. There are 12 chips on each side of the module.
Note
32-megatybe chips are larger than 8-megabyte chips.
Figure 221 32-Megabyte Simm

3
4
MLO-010946
See the section entitled Identifying and Locating Options and

Figure 210 for additional information.
235
Remove
Memory
To remove or replace a memory module, refer to Figure 222 and

perform the following steps:
Step
Action

to section entitled Preparing Your System for additional
information.
Remove memory beginning with the module closest to

device position 2. (See Identifying and Locating Options
and Figure 210 for the location of device position 2.)
Release the sprint clips
at both ends of the module.
Hold the module by its edges, tilt the module forward,

and pull up and out. .
Figure 222 Removing and Installing a Memory Module
3
1
MLO-010100
236
Install Memory
To install memory, reverse the steps in the removal procedure, as

follows, and refer to Figure 222:
Step
Action
Be sure all system preparation tasks are complete. See

the section entitled Preparing Your System for more
information.
away from
Hold the module at an angle with the notch
the power supply and the module pins facing the system
module.
Firmly push the module into the connector and stand the
module upright .
Make sure that the memory module snaps into the spring
clips at each end of the connector .
Continue adding modules, filling available connectors in

succession.
Note
To remove a memory module other than the last one,
release the spring clips of all memory modules starting
with the last one and progressing to the memory module
to be removed. The released memory modules may be
tilted out of the way, but not completely removed. After
removing the memory module in question and replacing
it with a new one, stand the remaining module(s)
upright, and snap the module into the metal retainers at
each end of the connector.
237
Removing and Installing a TURBOchannel Option (For Models 300/300X/300LX Systems)
Removing and Installing a TURBOchannel Option (For

Models 300/300X/300LX Systems)
Definition of
TURBOchannel
A TURBOchannel bus is a high-performance interconnection

that allows you to support up to two monitors and use a
variety of Digital options, third-party graphics, multimedia,
and communications options. The TURBOchannel bus is a
synchronous asymmetrical I/O channel that connects option
modules to the system module.
Multiscreen
Capability
Using a TURBOchannel module you can connect two (or more)

monitors: one to the built-in HX graphics module, and an
additional one (or two) to the HX or TX TURBOchannel modules
that you install. When you connect an additional monitor to the
TURBOchannel module in slot 0 or slot 1, it is the first console
device detected on the TURBOchannel, and therefore becomes
the console device.
238
Supported
TURBOchannel
Options
Table 24 lists the TURBOchannel options you can add to your

DEC 3000 Model 300/300X/300LX system:
Table 24 TURBOchannel Options

TURBOchannel Option
Customer Order
Number
Field Service Part

Number
HX 2D graphics accelerator, 1280 x 1024, 72 Hz
PMAGBBE/BF
542114303
TX 2D 24-plane color frame buffer (nonaccelerated),

1280 x 1024, 72 HZ (DEC OSF/1 AXP systems only)
PMAGBJA/JB
303579002
PXG+1 3D 8-plane Z-buffer, low-to mid-range,

1280 x 1024, 72 HZ
PMAGBDA/DB
5420116AA
PXG+1 3D 24-plane Z-buffer,2 low-to mid-range,

1280 x 1024, 72 HZ
PMAGBEA/EB
542018505
ZLXM1, 24-plane, 3D, Z-buffer (DEC OSF/1 AXP

systems only)
PMAGCAA
8-to-24-plane upgrade for PXG+ (requires Digital

Services installation)
PMAGGB
370125003
24-bit Z-buffer2 option for 8-plane PXG+ systems
PMAGHA
8-bit: 5420410AA
16-bit: 5420352AA
Denali P310 3D graphics, P510 3D graphics, and

V620 3D graphics, (DEC OSF/1 AXP systems only)
PEXGAAA/BA
/CA
Dual SCSI adapter
PMAZBCA
542183301
Dual SCSI adapter with fast SCSI support (8-bit,

5-MB/sec or 10-MB/sec ports)
PMAZC-AA
542183303
AUI (Thickwire) Ethernet module
PMADAA
541987401
FDDIcontroller 700 (fiber optic) interface
DEFTAFA
Sound and Motion J300 multimedia option
AV300AA
Prestoserve option
DJ30APSAA
Sync com option
DSYT-1
UTP (Twisted Pair) to 10BASE-2 (ThinWire)

adapter
DETTRAA/AB
UTP (Twisted Pair) to AUI (ThickWire) adapter
DETTR-BA/BB
703028401
1 3D
PXG+ options do not include DEC PHIGS Runtime license or DEC Open3D license (required for 3D
graphics); it must be ordered separately. One 3D option is supported per system; two TURBOchannel slots
required.
2A
Z-Buffer improves 3D graphics performance.
239
Antistatic
Precautions

the section entitled CAUTION: Static Discharge earlier in this
chapter for additional information.
Remove a
TURBOchannel
Option
To remove a TURBOchannel option, refer to Figure 223 and

follow these steps:
240
Step
Action
Be sure the system preparation tasks are complete. See

information.
Disconnect external cables to the TURBOchannel slots at

the back of the system unit.
Remove the two screws from the two posts at the back of
a single-width TURBOchannel module and four screws
from four posts at the back of a double-width module.
These screws secure the TURBOchannel module to the
system module.
Remove the two screws from a single-width module and

four screws from a double-width module on the back of
the system unit that hold the TURBOchannel module in
the connector slot. Save the screws for step 6.
Lift the single-width or double-width TURBOchannel

option up off the system connector and out toward the
front of the system unit. This may require extra effort, as
the TURBOchannel options are installed tightly.
Insert one or two filler plates, depending on the width

of the module, into the TURBOchannel slot openings,
and attach with the two or four screws from step 4. See
Figure 224.
Figure 223 Removing and Installing a TURBOchannel Option
MLO-009783
241
Install a
TURBOchannel
Option
To install a TURBOchannel option, reverse the removal

procedure, and refer to Figure 223 as follows:
Step
Action

information.
Remove the screws from the back of the system unit that
hold the filler plate or plates (depending on the width
of the module) in the TURBOchannel slot, as shown in
Figure 224. Save the screws to use in step 6. Save
the filler plate or plates in case you remove the option.
Reinsert the filler plate or plates when the option is
removed in order to maintain the EMI and thermal
integrity of the system.
Figure 224 Removing the TURBOchannel Filler Plate
MLO-009749
242
Insert the TURBOchannel option connector into the open

slot at the back of the system unit.
Firmly press the module onto the TURBOchannel

connector. This may require some extra effort, as
TURBOchannel options fit tightly.
Insert the two or four screws (that come with the option)
through the holes on the TURBOchannel module and into
the posts on the system module. Screw the module down
to secure the option to the system module.
Reinsert the screws (from step 2) to the back of the

system unit to hold the TURBOchannel option in place.
Connect external cables to the TURBOchannel option

at the back of the system unit. Refer to the option
documentation for proper cabling procedures.
243

Antistatic
Precautions

chapter. Handle the CPU module by its edges only.
Remove the
CPU Module
To remove the CPU module, refer to Figure 225 and perform

the following steps:
Step
Action

information.
Loosen the four captive (nonremovable) screws that hold

the module in place: two at the back corner edges of the
module and two at the center edges.
may remain attached to the
The four support posts
system module during CPU removal. However, they must
be removed before you remove the system module.
Warning
Do not use the aluminum heat sink ( in Figure 225)
as a handle. This part of the CPU module is very hot if
the system has recently been running.
244
Lift the module up off the system module connector and

out.
Figure 225 Removing the CPU Module

1
2
2
MLO-009788
Install the CPU

Module
To install the CPU module, reverse all steps in the removal

procedure and refer to Figure 225, as follows:
Step
Action
Be sure the system preparation task are complete. See

information.
Holding the module by its edges, set it onto the four posts
to which it attaches . (Do not handle the module by the
aluminum heat sink .) Push down on the connector end
of the module to ensure a good connection.
Tighten the four captive screws to the posts: two at the

back corner edges of the module, and two at the center
edges.
245

Antistatic
Precautions

chapter.
Remove the
Power supply
To remove the power supply, refer to figures 226 and 227, and
perform the following steps:
246
Step
Action

information.
Squeeze the plastic tab on the front of the power supply

cable connector and pull up to disconnect the cable from
the system module. See Figure 226.
If any drives are installed, disconnect the cable from these
drives as well.
Figure 226 The Power Supply Cable
2
MLO-010746
Each numbered component is identified as follows:
SCSI cable
Power cable
System module
Power supply
Device in position 1
Device in position 2
247
Step
Action
Remove the two mounting screws: one located at the

bottom front of the power supply on a metal tab facing
the inside of the system unit; the other located at the
back of the system unit next to the on/off switch. See
Figure 227.
Note
Do not confuse the back mounting screw with the back
screw of the power supply cover.
Slide the power supply toward the front of the system

unit, raise the back of the power supply above the back of
the system unit, and slide the power supply out.
Figure 227 Removing the Power Supply
MLO-009794
248
Caution: Shield
It is possible for the metal shield that is attached to the inside

of the system unit to come loose when you remove the power
supply. This shield is located at the back of the system unit and
encircles the opening through which the power supply sockets
extend (see Figure 228). If the shield comes loose, be sure to
reinstall it.
Figure 228 Reinstalling the Metal Shield
MLO-010728
Install the
Power Supply
To install the power supply, reverse all steps in the removal

Step
Action

information.
Insert the tab on the bottom front of the power supply

into the slot on the base plate of the system unit.
Push the power supply toward the back of the system

unit.
Insert and tighten the two mounting screws.
Connect the power supply cable connector to the system

module, and then a connector to each drive, if any are
installed.
249

Antistatic
Precautions

Remove the
Ethernet ROM
In the event that you must replace the system module, be aware
that you can retain your systems original Ethernet address, by
transferring the Ethernet ROM from the failing system module
to the new system module.
To remove the Ethernet ROM from the failing system module,
refer to Figure 229 and perform the following steps:
Step
Action

information.
Locate the Ethernet ROM on both the new and failing

system modules. The ROM is a 16-pin socketed chip; it
is labeled
in Figure 229. Note the orientation of the
ROM; there is a ROM key (a small notch) at the end of
the chip close to the memory modules.
Remove the Ethernet ROM from the replacement (new)

system module using a chip puller or a small flat-head
screwdriver. Put this ROM aside. Lift the chip gradually,
loosening first one end of the chip and then the other.
CAUTION
When you remove an Ethernet ROM, be very careful not
to bend the pins on the chip. The pins are fragile and
must be intact for you to add the Ethernet ROM to the
replacement system module.
250
Step
Action
Remove the Ethernet ROM from the failing system

module using a chip puller or a small flat-head
screwdriver. Lift the chip gradually, loosening first one
end of the chip and then the other.
Make sure the pins on the Ethernet ROM are straight

after you remove the ROM from the failing system
module. If the pins are bent, carefully straighten them.
Transfer and add the chip (that you just removed from
the failing system module) to the replacement system
module, installing it in the vacant Ethernet ROM socket.
Make sure you place the chip in the vacant socket in the
same orientation as it was in when you removed it from
the failing module. Make sure the pins on the Ethernet
ROM are properly aligned in the socket before pushing
the ROM into place.
Take the Ethernet ROM you removed from the new

system module and insert it in the vacant socket on the
failing system module.
Figure 229 Removing the Ethernet ROM
MLO-012103
251
Remove the
System Module
252
To remove the system module, refer to Figure 230 and perform

Step
Action

information.
Remove the TURBOchannel modules (Models 300/300X

/300LX only), see Figure 223.
Remove the TURBOchannel filler plates, see Figure 224.
Remove the power supply. See Figure 227.
Remove the CPU module. See Figure 225. The four

support posts may remain attached to the system module
during CPU removal. However, they must be removed
before you remove the system module.
Remove the drives, if any. Disconnect the SCSI cable from

the system module.
Remove the memory modules (SIMMs), see Figure 222.
Unscrew the four TURBOchannel posts labeled

Figure 230. (Models 300/300X/300LX only)
Unscrew the four CPU module support posts labeled

Figure 225.
10
Remove the two screws labeled
11
Before you remove the system module, remember to swap

the Ethernet chip, that is, move the chip from the old
module to the new module.
12
Gently pry the system module off the three standoffs,

labeled
in Figure 230, and pull the module toward
the front of the system unit (away from the connector/slot
openings on the bottom enclosure).
in
in
in Figure 230.
Note
After you remove the system module, you will see a loose
metal plate. Be sure this plate is in place when you
reinstall the system module. (See Figure 230.)
Figure 230 Removing the System Module
2
3
MLO-009781
253
Install the
System Module
254
To install the system module, reverse all steps in the removal

Step
Action

information.
Insert the connectors on the system module through

the openings on the bottom enclosure. Seat the system
and push down gently.
module over the standoffs
Add the two screws labeled
Screw the four TURBOchannel posts in place, see

Figure 230.
Add the four CPU module support posts, see

Figure 225.
Install the memory modules (SIMMs), see Figure 222.
Install the drive(s). Refer to the sections entitled

Removing and Installing a Removable-Media Drive and
Removing and Installing a Fixed Disk Drive.
Install the CPU module. Refer to the section entitled

Install the CPU Module.
Install the power supply. Refer to the previous section

entitled Install the Power Supply.
10
Connect the power cable and the internal SCSI cable to

the system module and the drives. See Figure 226.
11
Install the TURBOchannel modules and/or the option slot

filler plates. See figures 223 and 224.
12
Connect all cables to the back of the system unit.
in Figure 230.
in
in

Save the Wrist
Strap
Replace the
System Unit
Cover
After you have installed all the internal options you want to
install at this time, or have completed maintenance, remove and
save the antistatic wrist strap as follows:
Step
Action
Remove the copper end of the strap from the system unit.
Cover the sticky surface with the protective paper you

removed earlier.
Unwrap the strap from your wrist.
Refold the strap and save it in the envelope it came in for

future use.
To replace the system cover, see Figure 231 and follow these
steps:
Step
Action
Align the lip on the front inside edge of the cover

with
the four tabs along the front edge of the system unit .
Position the cover so that the lip fits over the tabs.
Maintain a slight pressure on the front of the cover

as
you lower it.
Be sure the sides of the cover fit over the outside of the
bottom enclosure.
Press down firmly on the edges of the cover.
Replace the two screws on the back of the system unit

that hold the cover in place .
255
Figure 231 Replacing the System Cover
ISDN
4
MLO-010101
256
Reconnect and
Restart the
System
To reconnect your system, follow these steps:

Warning
The monitor can weigh up to 75 lbs. (34 kg). To avoid
possible injury, two people are required to move the
monitor.
Step
Action
Return your monitor to its former position.
Connect the following components:

a. Monitor and system power cords.
b. Monitor video and mouse/keyboard cables.
c.
Network cable and optional adapter.
d. System power cord to a grounded outlet.

3
Turn on the following components:

a. Peripheral devices, such as a printer, modem, or
expansion box.
b. Monitor and system unit.
Note
If you do not turn on SCSI expansion boxes before you
turn on the system unit, the system will not recognize
the devices mounted in the SCSI expansion boxes.
Figure 232 shows the connections between the system unit,

monitor, mouse and keyboard, network, and grounded outlet.
257
Figure 232 Reconnecting the System
ISDN
MLO-010603
When you turn on the system successfully, you should see a

display similar to that shown in Figure 233. This display is
similar to the screen displayed when you enter the show config
console command.
258
Figure 233 System Display After Restoring Your System

DEC 3000 - M300
System conducting power up tests
----------------------------------------------------DEVNAM
DEVSTAT
------------CPU
OK KN16-AA - Vx.x-Syyy-Izzz - sx.x - DECchip 21064 P3.0
ASIC
OK
MEM
OK 32MB
NVR
OK
CXT
OK
SCC
OK ptr(0) = Present keybd(2) = Present
NI
OK Ethernet Address: 08-00-2B-2F-F8-E6 , TENBT
SCSI
OK
ISDN
OK
----------------------------------------------------System power up OK.
>>>
Test the System
To confirm that the options are connected correctly:

Step
Action
Enter the show device command at the console prompt

to display the status of the drives, as explained in the
section entitled Recording Information Before Making
Changes at the beginning of this chapter.
From this display, you can:
Compare the new display with the display you viewed

when you prepared the system. You should see the
new drive, and the drive that was in the system before
you made the addition. If the new drive is not in the
list, it has not been installed properly.
Verify that devices are set to the correct SCSI settings

(ADDR) so that all devices can be accessed.
Verify that there are no error messages. If there are

error messages, write them down. See Chapter 8.
259
Step
Action
Enter the show device command at the console prompt to

display a list of the devices in your system. If you have a
DEC 3000 Model 300/300X/300LX system, this command
will also display a list of your TURBOchannel modules.
Enter the show mem command at the console prompt

to verify that installation of additional memory was
successful.
At the console prompt (>>>), enter the set auto_action
boot command.
If your system has the OpenVMS AXP or the DEC OSF/1
AXP operating system software already installed, enter
B at the console prompt, and press the Return key to
automatically start your system. If you do not already
have operating system software, refer to your software
documentation.
Record
Messages
If any messages are displayed, write them down in case you need
to contact your Digital service representative.
If you see error messages during the startup or show config
procedure, check the following:
Are all cables inside and outside the system properly

connected?
Are all modules fully seated in their connectors?
Are SCSI switches and jumpers set correctly? (No two

devices should have the same SCSI ID setting.)
Are any SCSI ID addresses set to ID 7? The system SCSI

controller uses SCSI ID address number 7.
If gaining entry to the system unit is required for checking

cables and modules, refer back to the section entitled Preparing
Your System.
If you continue to see error messages, refer to Chapter 7 or
Chapter 8, or contact your Digital service representative.
260
3
Connecting External Options
Chapter Overview
In This Chapter
This chapter covers the following topics:
Headset
Tablet
Printers
Modems
Expansion Boxes
Compact Disc Drive
Future Options
The previous list represents the external options that are

available when the DEC 3000 Model 300 Series AXP System
first ships. Other options may be available later.
For More
Information
For information on the installation and use of these options,

consult the documentation accompanying the option. To
purchase an option, contact your Digital sales representative.
31
Headset
Headset
Purpose
You can use a headset (VSXXX-JA) as an
alternative to a telephone handset to input
and output audio data. The headset includes
a microphone for voice input, a cord with a
clothing clip, and a quick-disconnect connector
that allows you to move away from your
system without removing the headset. The
headset is compatible with both the OpenVMS
AXP and DEC OSF/1 AXP operating systems.
Tablet
Purpose
32
You can use either an 11-by-11-inch tablet

with a puck and pen pointer (VSXXX-AB)
or the standard mouse to position the
cursor on your monitor screen.
Printers
Printers
Recommended
Printers
Many printers, including third-party plotters, can be used with

your DEC 3000 Model 300 Series AXP system. See your Digital
sales representative for a list of the recommended printers.
Consult the documentation that came with the printer to unpack
the printer and set the baud rate.
Modems
Purpose
A modem is a device that converts computer signals to signals

that can be sent over a telephone line. Modems are typically
used for communications in large networks, such as wide area
networks (WANs).
A variety of modems can be used with your DEC 3000 Model
300 Series AXP system, the baud rate and model is specified
in the operating system documentation. See your Digital sales
representative for a list of the recommended modems.
Consult the documentation that came with the modem to unpack
the modem.
33
Expansion Boxes
Expansion Boxes
Available
Expansion
Devices
Expansion boxes allow you to add up to five additional

industry-standard SCSI devices external to your system.
A few of the devices you can add are the RRD42, RZ25,
RZ25L, RZ26, RZ26L, TZ30, and the TLZ06 drives. The
DEC 3000 Model 300 Series AXP systems support the BA353
expansion box. An optional dual-SCSI TURBOchannel option
card supports a maximum of 14 additional SCSI devices.
An optional pedestal mounting kit (BA350X-FA) is available for
the BA353 expansion box. See your Digital sales representative
for more information about this box and its options. Refer to
your expansion box documentation for mounting instructions.
Device
Verification
Be sure to refer to the operating system software product

description (SPD) to verify that all devices in a particular
expansion box are supported.
SCSI
Terminator
If no external devices are added, you must connect the SCSI

terminator to the SCSI port on the back panel of the system unit
to maintain signal integrity.
If external device(s) are added, you must connect a SCSI
terminator to the SCSI port on the last external device.
34
Compact Disc Drive
Compact Disc Drive

Introduction
The RRD42 compact disc drive is a half-height, 5-inch, 600megabyte storage device. You can connect the external model of
this drive to the SCSI port on the back panel of your DEC 3000
Model 300 Series AXP system (see External Device Connections )
and plug it in to an available outlet.
Refer to the 600 MB SCSI CD-ROM Installation Guide, listed in
Appendix D, for information on connecting cables to the RRD42
compact disc drive and on drive specifications.
Operating
System
Installation
If your system does not have factory-installed software, you can

load the operating system from an external compact disc.
For information on loading a disc into a caddy, and loading the
caddy into a compact disc drive, refer to either your operating
system installation documentation, or the instruction booklet
packed in the CD case.
35

Figure 31 shows where each of the external options connects to
the back panel of the system unit.
Connect an external compact disc drive or storage expansion
box to the SCSI port.
Connect a headset or handset to the audio input/output port.
Audio amplification is not provided by the system. To use
external speakers, you must provide amplification.
Connect a tablet to the connector block where the mouse
cable would otherwise be connected.
Connect a printer, plotter, modem or console terminal to
the RS232 synchronous/asynchronous communications
port. The RS232 port is normally used in asynchronous
mode. The communications port supports X.25 synchronous
communication, but the support is operating-system-specific.
Figure 31 External Connections to the System Unit
ISDN
4
MLO-009748
36
4
Using Console Commands
Chapter Overview
In This Chapter
This chapter lists and then explains the use of the DEC 3000
Model 300 Series AXP console commands and their parameters
and qualifiers. Each console command description includes a
summary of its purpose, a list of associated parameters and
qualifiers, and usage examples.
The following console commands are covered in this chapter:
boot
continue
deposit
examine
halt
help
initialize
login
repeat
set
show
start
test
Additionally, this chapter covers these topics:
Skill level required
Definitions of console and program mode
Three diagnostic environments
Diagnostic examples associated with the test command
41
Chapter Overview
Skill Level
Recommended
Using console commands requires basic, intermediate, and

sometimes advanced knowledge of your system and its
components, as well as the effect that console commands
can have on your system.
Skill Level
Recommended
Command
How Used
boot
Starts the operating system
Intermediate/
Advanced
continue
Returns from console mode

to operating system level
(program mode)
Advanced
deposit
Writes to specific memory, I/O,

and register locations from the
console
Advanced
examine
Displays contents of specific

memory, I/O, and register
locations
Advanced
halt
help
Halts the system
Basic
Displays the main help screen,

which is a list of six console
commands: boot, help
Basic
advanced, set, show, test

help
advanced
initialize
Displays advanced help
Intermediate
Resets console, devices, and

CPU
Intermediate
login
Gives you access to the

system and restricted console
commands if set password
command has been enabled
Intermediate
repeat
set
show
Executes commands repeatedly
Advanced
Sets an environment variable
Advanced1
Shows an environment
variable
Basic
start
test
Starts CPU at a given address
Advanced
Runs diagnostic tests
Intermediate
1 Exception:
42
set language is a basic command that sets the keyboard language.
Before You Begin
Before You Begin

Console Mode
Definition
In console mode, the system operates under the control of the

console subsystem, rather than the operating system. All user
input is passed to and interpreted by the console subsystem.
Console mode is in effect when the system is turned on and the
operating system software has not been started, or when the
operating system has been shut down.
When Console
Mode Is Used
Console
Prompt
You interact directly with the console subsystem under the

following circumstances:
Before booting the operating system software
While setting environment variables
When using the Firmware Update Utility
When trying to identify and resolve system problems or

errors (see Chapter 7 )
The console mode prompt looks like this:

>>>
You can enter control characters and console commands at the
console prompt.
Program Mode
Definition
In program mode, the system and console are under control of

the operating system. All user input is passed to the operating
system. You cannot issue console commands without returning
to console mode.
Program mode is in effect when the system is turned on and
the operating system software has started. In program mode,
the user can manage the system, run software applications, and
perform network tasks.
Program
Prompt
The program mode default prompt usually looks like this:

$
43
Before You Begin
Console
Mode Keys
and Control
Characters
Control characters are entered by holding down the key labeled

Ctrl while pressing another key, for example, Ctrl/C .
Table 41 lists the keys and control characters that you can use
while operating in console mode.
Table 41 Supported Keys and Control Characters
Key or Control
Character
Return
44
Function
The Return key executes the command that you

enter at the console prompt.
<x
The delete key deletes one character to the left

of the current command line position. On video
terminals, deleted characters will be erased
from the screen. On hardcopy terminals,
deleted characters display within a pair of
backslash delimiters (\ \) as they are deleted.
Ctrl/C
This character aborts the current command.

This command has no effect once control has
been passed from console mode to another
program, such as the operating system or a
loadable diagnostic application.
This command appears as ^C on the screen.
Ctrl/O
This character suppresses output to the console

terminal until the Ctrl/O control character is
pressed again.
This command appears as ^O on the screen.
Ctrl/S
This character suspends output to the console

terminal until you press Ctrl/Q .
Ctrl/Q
This character resumes the display that was

previously suspended by pressing Ctrl/S .
Before You Begin
What To Do
First
Before using any console commands, you should complete these

tasks:
If your operating system is running, use the shutdown

procedures specific to your operating system:
Operating
System
Before You
Change
Parameters
Shutdown Command
For Additional Information
OpenVMS
AXP
@sys$system:shutdown System Management,
DEC
OSF/1
AXP
shutdown -h now
Vol. 1A, Guide to Starting

Up and Shutting Down the
System
Guide to System
Administration
If your system is not displaying the >>> prompt, then place

your system in console mode by pressing the halt button
after the operating system is shut down.
Do not change any parameters without fully understanding the

effect the change may have on your system. If you are unsure of
what the change will be when you specify a command, then read
carefully the information in this chapter before you make the
change.
45
Before You Begin
CAUTION:
Control of
System Devices
Some console commands control system devices and memory. Do

not use console commands without fully understanding the effect
they can have on your DEC 3000 Model 300 Series AXP system.
For instance, some advanced-level commands, such as deposit
and set let you manipulate nonvolatile and system memory.
Using the deposit command to place a value in a location of
memory containing the actual console firmware could either
hang the system or prevent it from restarting after it is turned
off.
If you are not sure about using console commands, ask your
system manager for help.
Diagnostics
Three
Diagnostic
Environments
You can access three different diagnostic environments:

1. Power-up diagnostic environment
This mode applies only when power is first applied to the
system, and before the system reaches console level.
Note
The term startup, as used in text, describes the starting
up of your system from console mode.
2. Customer (console) diagnostic environment

For customer-run (console) diagnostics, first shut down the
operating system. If the console is not displaying the >>>,
then press the halt button on the back of the system unit.
Type the following command:
>>> set diag_s[ection] 1
46
Return
Diagnostics
From the customer (console) environment you can run a

single diagnostic test using, for example, the test command
and then specifying a device name. The following example
tests the NVR:
>>> t[est] nvr
Return
3. Service diagnostic environment

To run multiple tests with one command, and for a thorough
testing of your system, first shut down the operating system,
then press the halt button on the back of the system unit,
and type:
>>> set diag_s[ection] 2
Return
Note that there may be special requirements in order to

execute a certain test; for example, loopback connectors,
a handset, or a specific device may be required. See the
description of the test command.
You can run multiple diagnostic tests using, for
example, the test device_name,device_name or test
device_name:device_name commands. The test command is
described at the end of this chapter.
The following command tests the network interconnect (NI)
and nonvolatile random-access memory (NVR):
>>> t[est] ni,nvr
Return
47
BOOT
BOOT
Loads and
Starts
Operating
System
The boot command initializes the system and starts the boot
program, which loads and starts the operating system. There is
an 80-character limit on the input line, and there is no command
line wrap feature.
Format
Issue the boot command with the following syntax:
>>> b[oot] [-fl value][-fi filename]["slot_number/device_name"][-ns]
Parameters and
Qualifiers
Return
The boot command, and its parameters and qualifiers, are

described in Table 42.
Table 42 Parameters/Qualifiers for the boot Command
Parameter/Qualifier
Description
-fl value
The -fl boot flag is an ASCII string of

up to 23 characters. The string value
must be enclosed in quotation marks if it
is to be passed to the operating system
unmodified.
-fi filename
A filename of up to 23 characters, used to

specify the name of a file to load into the
system when booting across a network
device.
boot_device_name
A device name (such as dka300, rz3a

or a list of devices), from which the
system attempts to boot, or a saved
boot specification in the form of an
environment variable. One or more
default boot devices may be specified with
the set boot command.
48
BOOT
Table 42 (Cont.) Parameters/Qualifiers for the boot Command

Parameter/Qualifier
Description
-tc slot_number
[,net]
The TURBOchannel (-tc) slot number

you wish to boot through. This parameter
tells the boot class driver that it needs
to call the MIPS emulator to execute the
devices boot object. Quotation marks
" " are required when booting from a
TURBOchannel device. For example,
to set the default boot device and then
issue the boot command, enter these
commands:
>>> set bootdef_dev "1/DKA0"
>>> b "1/DK0" Return
Return
To boot from device DKA400 connected

to TURBOchannel slot 2, enter this
command:
>>> boot "2/dka400"
Return
To perform a MOP boot from a device

connected to TURBOchannel slot 3, enter
this command:
>>>boot "3/esa0" -fi "filename.sys"
Return
To perform a BOOTP boot (tftp) from a

device connected to TURBOchannel slot
4, enter this command:
>>>boot "4/ez0" -fi "/tmp/vmunix"
Return
The user must specify a value for ,net

if the device is a network device. For
example, the following command lines
boot a system from the network device in
TURBOchannel slot 1:
>>> b "1/ES"
Return

49
BOOT
Table 42 (Cont.) Parameters/Qualifiers for the boot Command
Using the boot

Command
Parameter/Qualifier
Description
-ns
Tells the console to not start the code

after it has been loaded. This parameter
can be used as a debug tool.
Issuing the boot command with the -fl, -fi qualifiers and
boot_device_name parameter overrides the current default
value for the current boot request, but it does not change the
stored default value.
If no device name is specified with the boot command,

the default boot device, stored using the set bootdef_dev
command , is assumed.
If no flag is given, then the default value is read from

the environment variable stored by the set boot_osflags
command. If no value is specified for the flags, the value (0,
0) is assumed.
Additional information about boot flags is provided in your

operating system documentation.
For this operating
system...
410
Refer to the...
OpenVMS AXP
OpenVMS AXP Installation and Upgrade

Manual
DEC OSF/1 AXP
Guide to Installing DEC OSF/1 AXP
BOOT
Boot Device
Names and
Naming
Conventions
A device is a hardware unit connected to your DEC 3000 Model

300 Series AXP system that is capable of receiving, storing, or
transmitting data. The device name is a special identifier that is
recognized by the system.
The device names used in booting a DEC OSF/1 system are
identical to those used in booting an OpenVMS AXP system:
the DK/MK/ES device names shown in Table 43 apply to both
operating systems. In addition, a DEC OSF/1 system can be
booted using the alternate device names (RZ/TZ/ES/EZ) also
shown in Table 43.
Table 43 Device Names
OpenVMS
AXP
Device Name
DEC OSF/1
AXP
Device Name
Device Type
DK
RZ
Fixed or removable disk
MK
TZ
Tape
ES
ES
Ethernet boot using MOP

protocol
EZ
Ethernet boot using bootp

protocol. Refer to your
DEC/OSF1 operating system
documentation for information
on the bootp protocol.
411
BOOT
Conventions
for Both
Operating
Systems
The device naming convention common to both the OpenVMS

AXP and DEC OSF/1 operating system is ddiunn. The alternate
device naming convention for the DEC OSF/1 operating system
is ddui. See Table 44 and Table 45 for descriptions of these
conventions.
Table 44 Naming Convention Common to Both Operating
Systems
Convention
Description
dd
Device name identifier from Table 43
Designates SCSI controller (A)
Designates the SCSI ID number, also known as

a logical unit number (LUN).
nn
Designates SCSI sub-logical unit number (subLUN), with the default of 00
Table 45 Alternate Naming Convention for DEC OSF/1 System
412
Convention
Description
dd
Device name identifier from Table 43
Designates the SCSI ID number, also known as

a logical unit number (LUN).
Designates SCSI controller (A)
BOOT
A disk device with a SCSI ID of 3 and a sub-LUN of 00 could

have the following device name:
dka300
A disk device with a SCSI ID of 3 could have an alternate OSF/1
device name:
rz3a
Example:
Default Boot
The following example specifies the default boot command:

>>> boot
Example:
Overriding the
Default Boot
Return
The following example overrides the current default boot

environment settings. It does not change the default values
stored as environment variables.
>>> boot -fi "myboot.com"
Example:
Device Boot
The following example boots from:
DK the disk device
A SCSI controller A
3 SCSI ID 3
00 LUN 00
>>> boot dka300
Example:
DEC/OSF1
Network Boot
Return
The following example performs a network boot:

>>> boot -fi "mop/tmp/vmunix" "1/esa0"
Return
413
BOOT
Example:
OpenVMS
Network Boot
The following example performs a Maintenance Operations

Protocol (MOP) boot to device ESA0 with the flags equal to 0,0.
>>> b -fl 0,0 esa0
Return
To perform a MOP boot from another node over the network on

OpenVMS systems, follow these steps and refer to the example
that follows:
1. Identify the Ethernet address of the node you want to boot
2. Set trigger on
3. Set mop on
$ mc ncp
Return
! From any non-privileged account
NCP>>> trigger via sva-0 phy add 08-00-2b-2a-1f-82 ser pass

1234567890abcdef Return
Follow these steps to access the console on a remote system:

1. Identify the Ethernet address of the node you want to boot
2. Set trigger on
3. Set mop on
$ mc ncp
Return
! From any non-privileged account
NCP>>> conn via sva-0 phy add 08-00-2b-2a-1f-82 ser pass

1234567890abcdef Return
414
>>> login
PSDWO>>>
Return
Return
! Enter password
>>> exit
Return
! Console mode
CONTINUE
CONTINUE
Returns System
to Program
Mode
The continue command returns the system to program mode

(operating system level), after console mode has been invoked.
Note
The continue command is supported only on the
OpenVMS operating system.
Your operating system should resume execution after you enter

this command, providing that the contents of memory used by
the operating system have not been altered or corrupted. The
processor begins instruction execution at the address contained
in the program counter. Commands that can corrupt or alter
system memory include the test and deposit commands. This
command does not initialize the processor.
The following function is not supported on a graphics console:
Ctrl/P
/continue
This function works only on the alternate console.

Format
To execute the continue command, use the following syntax:
>>> c[ontinue]
Example
Return
The following example returns the system from console mode to

program mode.
>>> c
Return
415
DEPOSIT
DEPOSIT
Writes to
Memory
The deposit command is used to write to memory locations

from the console. If no address space or data size options are
specified, the defaults are the last address space and the data
size used in a deposit or examine command.
Format
To execute the deposit command, use the following syntax:
>>> d[eposit] [-{size_option}] [-{address_option}] [-{misc_opts}] {address} {data}
Return
The {address} qualifier specifies the address (or first address) to

be written. Data values must be in hexadecimal form.
Parameters and
Qualifiers
The [-{size_option}] qualifiers specify data size:

Size
Option
-b
-w
-l
-q
1 The
Description
byte (8 bits)1
word (16 bits)1
longword (32 bits) (default)1
quadword (64 bits)1
size option qualifiers conflict with all of the

as all processor registers are quadwords.
416
examine register commands,
DEPOSIT
The [-{address_option}] qualifiers specify address type:

Address
Option
-vm[em]
-pm[em]
ps
Description
The address space is virtual memory.

The address space is physical memory (default)
Processor status register (PS). The data size is always
a quadword.1
-u
Unprotects a protected memory location. Use

caution when depositing information in memory
locations 0 - 200000, as they contain the console code,
hardware restart parameter block, console routine
block, console terminal block, memory descriptors,
page tables, etc. Be aware that the -u qualifier gives
you unprotected access to these registers.
-r
General purpose register, R0 through R31. The data

size is always quadword.
-fr
Floating point register, FR0 through FR31. The data

-i
Internal processor registers (IPRs). The data size is

always quadword.
pc
sp
Program counter. The data size is always quadword.1
1 This
Stack pointer. The data size is always quadword.1

option should not be typed with the hyphen (-).
417
DEPOSIT
The [-{miscellaneous_options}] qualifiers specify

miscellaneous information.
Miscellaneous
Option
Description
-n{value}
Specifies the number of consecutive locations to

modify. The information specified in {value} is
deposited to the first address, and then to the
specified number of succeeding addresses.
-s{value}
-u{value}
Address increment size.

Access to console private memory is allowed. This
option disables virtual address protection checks.
The {address} qualifier is a longword that specifies (in

hexadecimal form) the first location into which data is deposited.
Supported
Symbolic
Addresses
418
Description
The location last referenced in an examine or

deposit command.
The location immediately following the last

location referenced in an examine or deposit
command.
The location immediately preceding the last

location referenced in an examine or deposit
command.
An indirect operation. Take the address specifier

and use it as the pointer to the data.
DEPOSIT
The {data} qualifier specifies the data to be deposited. If the

specified data is larger than the deposit data size, the console
ignores the command and issues an error response. If the
specified data is smaller than the deposit data size, it is extended
on the left with zeros.
Examples
The following example writes a value of 01234567 into six

longword locations starting at address 00100000:
>>> d -u -pm -n:5 00100000 01234567
Return
The following example deposits FFFF to general purpose

registers R0 through R2:
>>> d -r -n 2 0 ffff
Return
The following example deposits F to stack pointer:

>>> d sp f
Return
419
EXAMINE
EXAMINE
Displays
Memory
Locations
The examine command examines and displays the contents of the

specified memory location. The displayed line consists of a single
character address specifier, the hexadecimal physical address to
be examined.
After initialization, the default address space is physical memory,
the default data size is a longword and the default address is
zero. If conflicting address space or data sizes are specified, the
console ignores the command and issues an error response.
Format
To execute the examine command, use the following syntax:
>>> e[xamine] [-{size_option}][-{address_option}] [-{miscellaneous_options}] [{address}]
Return
The {address} qualifier specifies the address (or first address) to

be read.
Parameters and
Qualifiers
Except for the -u miscellaneous option, the console code

remembers the qualifiers specified in the last command and
continues in that mode until you provide a new qualifier. For
example:
>>> e r0
GPR: 00 00000000 0000000
>>> e 100000
?22 ILL REF
The above sequence produces an illegal address error, as there is
no address r100000. The following sequence is required:
>>> e r0
GPR: 00 00000000 00000000
>>> e -pm -u 100000
PMEM: 00000000.00100000 4C202343 54205420
In the above sequence, the -u (unprotected) qualifier was added
to the command line.
420
EXAMINE
CAUTION
Use caution when examining registers 0 - 200000, as they

contain the console code, hardware restart parameter block,
console routine block, console terminal block, memory descriptors
and page tables. Be aware that the -u qualifier gives you
unprotected access to these registers.
The [-{size_option}] qualifiers specify data size:
Data
Option
Description
byte (8 bits)1
-b
-w
-l
-q
word (16 bits)1

longword (32 bits) (default)1
quadword (64 bits)1
1 The
data option qualifiers conflict with all of the

as all processor registers are quadwords.
examine register commands,
The [-{address_option}] qualifiers specify address type:

Address
Option
-vm[em]
-pm[em]
ps
Description
The address space is virtual memory.

The address space is physical memory (default).
Processor status register (PS). The data size is always
a quadword.1
-u
-r
Unprotects a protected memory location.
-fr
Floating-point register, FR0 through FR31. The data

-i
Internal processor registers (IPRs). The data size is

always quadword.
pc
sp
Program counter. The data size is always quadword.1
1 This
General-purpose register, R0 through R31. The data

Stack pointer. The data size is always quadword.1

option should not be typed with the hyphen (-).
421
EXAMINE
The miscellaneous_options qualifiers specify miscellaneous

information.
Misc
Option
-n {value}
-s {value}
-u
Description
Specifies the number of locations to be read.

Specifies address increment size. Default is data
size.
Access to console private memory is allowed.
The following qualifier specifies type of display.

Display
Option
-a
Description
Interpret and display data as ASCII data. Nonprinting characters are displayed as a period (.).
The {address} qualifier is a longword that specifies (in

hexadecimal form) the first location into which data is deposited.
Supported
Symbolic
Addresses Description
422
The location last referenced in an examine or deposit

command.
The location immediately following the last location

referenced in an examine or deposit command.
The location immediately preceding the last location

referenced in an examine or deposit command.
An indirect operation. Take the address specifier and

use it as the pointer to the data.
EXAMINE
Examples
This example reads the Hardware Restart Parameter Block
register (HRPB) with ASCII for 10 locations starting at location
0.
>>> e-u-q-a-n: 10 0
Return
Result:
00000000.00000000
00000000.00000008
00000000.00000010
00000000.00000018
00000000.00000020
00000000.00000028
00000000.00000030
00000000.00000038
00000000.00000040
00000000.00000048
00000000.00000050
00000000.00000058
00000000.00000060
00000000.00000068
00000000.00000070
00000000.00000078
00000000.00000080
........
........
........
........
........
........
........
........
........
........
........
........
........
........
........
........
........
This example will examine general-purpose registers R0 through

R2.
>>> e-r-n 2 0
Return
GPR: 00 00000000 00000000

GPR: 01 00000000 00000000
GPR: 02 00000000 00000000
The following example examines the stack pointer.
>>> e sp Return
GPR: 1E 00000000 00000000
The following example examines general-purpose register 5.
>>> e r5
GPR: 05 00000000 00000000
The following example examines floating-point register 4.
>>> e fr4
423
HALT
HALT
Halts the
System
The halt command halts the system. There are no parameters

associated with this command.
Format
Issue the halt command as follows:
>>> h[alt]
Return
The system halts and the following message displays:

?2E HLTED
>>>
424
HELP
HELP
Displays List of
Commands
The help command displays a brief list of commands,

parameters, and qualifiers. If you specify set, show, or
mips_[emulator], you will receive further information for
that topic only. The help command is not intended to provide a
complete description of each command. For a more complete list
of commands, use the help advanced command.
Format
To execute the help command, use the following syntax:
>>> he[lp] [advanced][set][show][mips_emulator]
Example: help
Command
RETURN
The help command used alone displays the main help screen.
>>> help
Return
Result:
BOOT
HELP ADVANCED
INITIALIZE
TEST
425
HELP
Example: help
advanced
Command
The help advanced command displays a list of the advanced

commands.
>>> help advanced
Return
Result:
BOOT [-FL <bflg> ] [-FI <filnam>]
CONTINUE
DEPOSIT [{ -B | -W | -L | -Q | -A
[{ <addr> | <sym> | + | EXAMINE [{ -B | -W | -L | -Q | -A
[{ <addr> | <sym> | + | HALT
HELP [MIPS_EMULATOR | SET | SHOW]
INITIALIZE
LOGIN
REPEAT <cmd>
START <addr>
TEST <devnam> [<tstnam>]
426
<devlist>
}] [{
| * |
}] [{
| * |
-PM | -VM }] [-U] [-N:<n>]

@ } [<datum>]]
-PM | -VM }] [-U] [-N:<n>]
@ }]
HELP
Example: help
set Command
The help set command displays a list of set command

parameters and qualifiers.
>>> help set
Return
Result:
SET[ENV]
SET[ENV}
SET[ENV]
SET[ENV]
SET[ENV]
SET[ENV]
SET[ENV]
SET[ENV]
SET[ENV]
SET[ENV]
SET[ENV]
SET[ENV]
SET[ENV]
SET[ENV]
SET[ENV]
SET[ENV]
AUTO_ACTION <{RESTART | 1} | {BOOT | 2} | {HALT | 3}>

BOOTDEF_DEV <ddau>
BOOT_OSFLAGS <bflg>
BOOT_RESET <{OFF | 0} | {ON | 1}>
DIAG_LOE <{OFF | 0} | {ON | 1}>
DIAG_QUICK <{OFF | 0} | {ON | 1}>
DIAG_SECTION <1-3>
ENABLE_AUDIT <{OFF | 0} | {ON | 1}>
LANGUAGE <0-15>
MOP <{OFF | 0} | {ON | 1}>
PASSWORD
RADIX < 0 | 10 | 16 >
{SCSI_A} <0-7>
SCSI_RESET <0-7>
SECURE <{OFF | 0} | {ON | 1}>
TRIGGER <{OFF | 0} | {ON | 1}>
427
HELP
Example:
help show
Command
Entering the help show command displays a list of show

command parameters.
>>> help show
Return
Result:
PRINTENV |
SHOW { AUTO_ACTION
BOOT_RESET
DIAG_LOE
ENABLE_AUDIT
LANGUAGE
RADIX
SECURE
}
Example: help
mips_emulator
Command
|
|
|
|
|
|
|
BOOTDEF_DEV
CONFIG
DIAG_QUICK
ETHERNET
MEMORY
SCSI_A
TRIGGER
BOOT_OSFLAGS
DEVICE
DIAG_SECTION
ERROR
MOP
SCSI_RESET
|
|
|
|
|
|
The help mips_emulator command displays a list of

TURBOchannel tests.
>>> help mips_emulator
Return
Result:
T
T
T
T
T
T
T
428
|
|
|
|
|
|
TC#
TC#
TC#
TC#
TC#
TC#
TC#
<tstnam>
?
SCRIPT <scriptnam>
INIT
CNFG
LS
CAT <scriptnam>
INITIALIZE
INITIALIZE
Initializes
Processor,
Console, and
Devices
The initialize command initializes the processor, console,

and any devices connected to the system by default values. In
order to guarantee the state of the system, the console program
will also initialize r0 through r30 to 0 and the ISO and OC to
20000000.
Format
To execute the initialize command, use the following syntax:
>>> i[nitialize]
Example:
initialize
Command
Return
This example initializes the processor, console, and any devices

connected to the system.
>>> i
Return
Result:
INIT-S-CPU...
INIT-S-RESET_TC...
INIT-S-NVR...
INIT-S-CXT...
INIT-S-ASIC...
INIT-S-MEM...
INIT-S-SCC...
INIT-S-NI...
INIT-S-SCSI...
INIT-S-ISDN...
429
LOGIN
LOGIN
Use with Set
Password
Command
The login command enables restricted console commands, such

as those used in the Set Password Utility, when:
the secure jumper is installed on the system module
the password has been set and secure is set to on

Note
After set secure is set to on, type login at the >>>
prompt. Type your password at the PSWD0>>> prompt.
Format
To execute the login command, use the following syntax:
>>> lo[gin] Return
PSWD0>>> console_password
Example: login
Command
This example enables access to restricted console commands

when the secure bit is set.
>>> login
PSWD0>>>
430
Return
Return
REPEAT
REPEAT
Repeats
Specified Tests
The repeat command causes the console program to repeatedly

execute any specified tests. It is terminated by pressing Ctrl/C
or by pressing the Halt button. There are no defaults for this
command.
Format
To execute the repeat command, use the following syntax:
>>> r[epeat] command {qualifier_list},...
Parameters and
Qualifiers
Return
The command variable specifies the command to be executed.

This can be any valid console command listed in this chapter.
The qualifier_list variable specifies the tests to be repeated, but
is not required, for example:
ASIC
MEM
NVR
SCC
NI
ISDN
Examples:
repeat
Command
The following examples show acceptable command format:

>>> r test
>>> test scc mouse
>>> r test scc:ni
The next example permits the ASIC (application-specific
integrated circuit) test to be repeated.
>>> r[epeat] t[est] asic
Return
The following example permits the ASIC, memory and SCSI

tests to be repeated.
>>> r[epeat] t[est] asic,mem,scsi
Return
431
SET
SET
Sets an
Environment
Variable
The set[env] command:
Sets an environment variable to a value or setting
Displays the value specified
Defines a command qualifier
Defines the console password
Format
To execute the set command, use the following syntax:
>>> set[env] environment [value]
432
Return
SET
Environment
Variables and
Values
Table 46 provides a list of the environment variables that can

be specified when the set command is used.
Table 46 set[env] Command Environment Variables and
Values
Environment
Variable
Variable Description
Value
Value
Description
auto_action
Specifies the action

the console should
take after a halt.
Restart
(or use 1)
Boot
(or use 2)
Halt
(or use 3)
A restart is
executed.
A reboot is
executed.
A halt is
executed
bootdef_dev
Sets the default

boot device. The
device names must
be valid boot devices
supported by the
boot command.
Entering "." resets
the boot device to the
default value.
boot_osflags
Defines additional
default values that
will be passed to
system software
during booting. The
value must be an
ASCII string, eight
characters in length,
and set in quotations
( " ). A comma ( , ) is
not one of the special
characters.
See
Table 47.
433
SET
Table 46 (Cont.) set[env] Command Environment Variables

and Values
Environment
Variable
Value
Description
Value
Determines if the
console will initialize
the system prior
to booting. Digital
recommends that
boot_reset be set to
On.
On
(or use 1)
diag_loe
Allows a diagnostic
to loop on error. All
output is suppressed.
To exit the loop,
press the Halt
button to return
to the diagnostic
environment (either
console or service
mode). This feature is
available on loadable
diagnostics only.
It will not work
on TURBOchannel
devices.
On
(or use 1)
Off
(or use 2)
Enables loop on
error feature.
Disables loop on
error feature.
diag_quick
Sets the diagnostic

startup mode to either
normal or fast startup
testing. When fast
mode is selected, not
all diagnostic tests
are executed.
On
(or use 1)
Off
(or use 2)
Quick verify
testing only.
Normal (full)
testing occurs.
diag_section
Sets the diagnostic

environment in which
diagnostics can be
run, either console or
service mode.
See
Table 48
boot_reset
Off
(or use 2)
Enables system
initialization
before booting.
Disables system
initialization
before booting.
434
SET

and Values
Environment
Variable
Value
Value
Description
enable_audit
Determines whether
or not the boot
audit trail message
generation is enabled.
On
(or use 1)
Off
(or use 2)
Enables boot
audit trail.
Disables boot
audit trail.
language
Sets the keyboard

language. Entering
See
Table 49
set language
without a qualifier
displays a list of
keyboard languages
from which you make
a selection. English
(3) is the default
value setting.
mop
Enables the NI
(Ethernet) listener
while the system
is in console mode.
The listener can
send and receive
messages on the
network. Determines
whether or not the
boot audit trail
message generation
is enabled. Digital
recommends that
you keep the mop
environment set to off
(except when you plan
to use it, after which
you should return the
status to OFF).
On
(or use 1)
Off
(or use 0)
Network
listener
enabled. Able
to receive
and transmit
messages on
the network.
(Default)
Network
listener
disabled.
435
SET

and Values
Environment
Variable
password
radix
Value
Description
Value
Sets the console

password. The
console secure
jumper must be
installed on the
system module. See
Chapter 5. The
password must be
exactly 16 characters
(hexadecimal) 0
through 9, and A
through F.
On
(or use 1)
Defines the default

Radix to a specified
value. The default is
hexadecimal.
Off
(or use 0)
Default base
address
(hexadecimal).
Decimal base
address.
Hexadecimal
base address.
10
16
scsi_reset
Causes a time delay

(in milliseconds) after
a SCSI reset and
before booting the
system.
Password is
enabled when
secure = on.
Password
disabled when
secure = off.
0 through 7
Use 3 for a
removablemedia
drive.
Use 4
(default) for
tape drives.
Use 6 for
CDs.
The value
is n in the
expression 2n .
For example,
a value of 3 is
23 and means
8 seconds. The
default is 24
436
SET

and Values
Environment
Variable
Value
Value
Description
secure
Enables the console

password bit to
restrict access to
the console. This
command works in
conjunction with
the console secure
jumper located on the
system module. See
Chapter 5.
On
(or use 1)
Off
(or use 0)
Secure feature
is enabled.
Secure feature
disabled.
trigger
Enables the EntityBased Module (EMB).

With EMB and the
NI listener enabled
(trigger = on), you can
boot the system from
a remote system.
On
(or use 1)
Off
(or use 0)
Enables trigger.
Disable trigger.
437
SET
Example: set
auto_action
Command
To execute the set auto_action command, use the following

syntax:
>>> se[t] auto[_action] {value}
Return
The following example sets the auto action default to halt.

>>> set auto 3
Return
Result:
AUTO_ACTION = HALT
Example: set
bootdef_dev
Command
To execute the set bootdef_dev command, use the following

syntax:
>>> set bootdef_dev {value}
Return
Issuing the show device command displays the available boot

devices.
The following example shows the boot default device being set to
dka200.
>>> set bootdef_dev dka200
Return
Result:
boot = dka200
Example: set
boot_osflags
Command
To execute the set boot_osflags command, use the following

syntax:
>>> set boot_osf[lags] {value}
Return
Table 47 describes the values to be used with the boot_osflags

environment and the OpenVMS operating system.
438
SET
Table 47 boot_osflags Command Values

Root
Contents of R5
Description
Default boot of operating system
Boot standalone backup1
Conversational boot
1 If
installed on disk
The following example initiates a default boot of the operating

system.
>>> set boot_osf 0,0
Example: set
boot_reset
Command
Return
To execute the set boot_reset command, use the following syntax:

>>> set boot_r[eset] {value}
Return
The following example enables the system initialization before

booting.
>>> set boot_r on
Return
Result:
BOOT_RESET = ON
Example:
set diag_loe
Command
To execute the set diag_loe command, use the following syntax:

>>> set diag_loe [value]
Return
The following example sets up a loop on error.

>>> set diag_loe on
Return
Result:
DIAG_LOE = ON
439
SET
Example: set
diag_quick
Command
To execute the set diag_quick command, use the following

syntax:
>>> set diag_q[uick] [value]
Return
The following example sets the diagnostic startup mode to quick

verify testing.
>>> set diag_q on
Return
Result:
DIAG_QUICK = ON
Example: set
diag_section
Command
To execute the set diag_section command, use the following

syntax:
>>> set diag_s[ection] {value}
Return
Select one of the following values to set the diagnostic

environment.
Table 48 set diag_section Command Values
440
Value
Mode
Description
Power-up
Power-up operation.
Customer
(Console)
Default mode after power is applied to

system
Service
Sets up diagnostic environment. Provides

for more thorough testing. Loopback
connectors may be required to execute
certain tests.
SET
In the following example, the diagnostic environment is set to

console mode.
>>> set diag_s 1
Return
Result:
DIAG_SECTION = 1
Example: set
enable_audit
Command
To execute the set enable_audit command, use the following

syntax:
>>> set enable_a[udit] {value}
Return
The following example enables the boot audit trail.

>>> set enable_a on
Return
Result:
ENABLE_AUDIT = ON
Example:
set language
Command
To execute the set language command, use the following syntax:

>>> set l[anguage] {value}
Return
441
SET
Select one of the following values to set the appropriate

language:
Table 49 Selecting a Keyboard Language
Value
Language Selected
0) Dansk
Danish
1) Deutsch
German
2) Deutsch (Schweiz)
German/Swiss
3) English
North American English

(default setting)
4) English
British/Irish
5) Espaol
Spanish
6) Franais
French
7) Franais
Canadian French
8) Franais
Swiss French
9) Italiano
Italian
10) Nederlands
Dutch
11) Norsk
Norwegian
12) Portugus
Portuguese
13) Suomi
Finnish
14) Svenska
Swedish
15) Vlaams
Flemish
The following example sets the language to Spanish.

>>> set language 5
Result:
LANGUAGE = 5
>>>
442
Return
SET
Example: set
mop Command
To execute the set mop command, use the following syntax:

>>> set mop {value}
Return
The following example enables the network listener while the

system is in console mode.
>>> set mop on
Return
Result:
MOP = ON
>>>
Example: set
password
Command
To execute the set password command, use the following syntax:

>>> set pass[word]
Return
The following example sets the password.

>>> set password
Return
Result:
PSWD0> old_password
PSWD1> new_password
PSWD2> new_password
!Type old password (if one has been set)

!Type new password
!Verify new password
>>>
Example:
set secure
Command
To execute the set secure command, use the following syntax:

>>> set sec[ure] {value}
Return
The following example enables the security features.

>>> set secure on
Return
Result:
SECURE = ON
443
SET
Example: set
radix Command
To execute the set radix command, use the following syntax:

>>> set ra[dix] {value}
Return
The following example sets the address to a decimal base

address.
>>> set radix 10
Return
Result:
RADIX = 10
Example: set
scsi_reset
Command
To execute the set scsi_reset command, use the following syntax:

>>> set scsi_r[eset] {value}
Return
The following example sets a time delay of 4 milliseconds

(default).
>>> set scsi_r 4
Return
Result:
SCSI_RESET = 4
Example:
set trigger
Command
To execute the set trigger command, use the following syntax:

>>> set tri[gger] {value}
Return
The following example enables trigger.

>>> set trigger on
Result:
TRIGGER = ON
444
Return
SHOW
SHOW
Shows
Environment
Variables
Your system is shipped with default values set for all available
parameters. The show console command displays the following
information:
Environment variables
Console options
Hardware configuration
Format
To display the current values for a specified environment
variable, type:
>>> show {variable}
Return
To display the current value for all variables, type:

>>> show
Return
445
SHOW
Environment
Variables and
Values
Table 410 provides a list of the environment variables that can

be specified when the show command is used.
Table 410 Environment Variables and Values for the show
Command
Environment
Variable
auto_action
Value
Value Description
Displays the action

the console takes
following an error
halt or a halt during
startup.
Restart
A restart was
executed.
A reboot was
executed.
A halt was
executed.
Boot
Halt
bootdef_dev
Displays the default

boot device or device
list from which
booting will next be
attempted.
boot_osflags
Displays default
parameters passed
to system software
during booting.
On
Displays the value

of the boot_reset
variable.
On
boot_reset
System
initialization
enabled.
System
initialization
disabled.
Off
System
initialization
enabled.
System
initialization
disabled.
Off
config
Displays the system

configuration and
device status.
device
Displays SCSI and

Ethernet device
information.
See
Chapter 2.
diag_loe
Displays the
diagnostic loop
on error feature.
On
Off
Loop on error
enabled.
Loop on error
disabled.
446
SHOW
Table 410 (Cont.) Environment Variables and Values for the

show Command
Environment
Variable
Value
Value Description
diag_quick
Displays the
diagnostic startup
mode, either normal
or fast.
On
Off
Fast testing.
Normal testing.
diag_section
Displays the
diagnostic
environment
0
1
2
Startup.
Customer.
Service.
enable_audit
Displays the boot

audit trail message
generation.
On
Off
Enabled.
Disabled.
error
Displays error
information for
ASIC, MEM, NVR,
SCC, NI, ISDN,
SCSI. See example
in value column.
Error message
indicator.
FRU number.
Name of the
diagnostic test
that detected an
error.
Error number in
hexadecimal form.
004
SCC
0x0060
ethernet
Displays the
hardware Ethernet
address and
Ethernet port.
language
Displays the
keyboard language
(only if your system
has a graphics
head). Identifies the
language in which
console messages
are displayed.
English
mem
Displays memory
status information
0-7
008
Mbytes
0x00000000
Bank number.
Memory size per
bank.
Starting address of
each bank.
447
SHOW
Table 410 (Cont.) Environment Variables and Values for the

show Command
Environment
Variable
mop
Value
Value Description
Displays the NI
(Ethernet) listener.
On
Network listener
enabled. Receive
and transmit
network messages.
Network listener
disabled.
Off
secure
radix
Displays system
security status. This
command works in
conjunction with
the console secure
jumper located on
the system module.
On
Displays the
default Radix (base
number).
Off
10
16
Example: show
Command
scsi_a
Displays the SCSI

ID for the system
bus
Value = 0
through 7.
scsi_reset
Displays the
time delay (in
milliseconds) after
a SCSI reset and
before booting.
Value = 0
through 7.
trigger
Displays the current

trigger setting.
On
Off
Default base
address (hexadecimal form.)
Decimal base
address.
Hexadecimal base
address.
Number of the
host ID.
Trigger enabled.
Trigger disabled.
The following example displays the current values for all

environment variables.
>>> sh[ow]
448
Secure feature
enabled.
Secure feature
disabled.
Return
SHOW
Result:
AUTO_ACTION = RESTART
BOOTDEF_DEV = DKA100
BOOT_OSFLAGS = 0,0
ENABLE_AUDIT = ON
BOOT_RESET = ON
SCSI_RESET = 4
DIAG_LOE = OFF
DIAG_QUICK = ON
DIAG_SECTION = 1
ETHERNET = 08-00-2B-2F-F8-E6 , TENBT
LANGUAGE = 3
MOP = OFF
SECURE = ON
RADIX = 0
SCSI_A = 7
TRIGGER = ON
Example: show
auto_action
Command
To execute the show auto_action command, use the following

syntax:
>>> sh[ow] auto_a[ction]
Return
The following example shows the action the console takes after a
halt.
>>> sh auto_a
Return
Result:
AUTO_ACTION = RESTART
Example: show
bootdef_dev
Command
To execute the show bootdef_dev command, use the following

syntax:
>>> sh[ow] bootdef_d[ev]
Return
The following example shows that the default boot device is

dka400.
>>> sh bootdef_d
Return
Result:
boot = dka400
449
SHOW
Example: show
boot_osflags
Command
To execute the show boot_osflags command, use the following

syntax:
>>> sh[ow] boot_o[sflags]
Return
The following example displays the current osflags stored in the

system.
>>> show boot_o
Return
Result:
BOOT_OSFLAGS = 0,0
>>>
Where 0,0 refers to the contents of the root and of register 5, as
follows:
Root
Contents of R5
Description (OpenVMS system)
Default boot of operating system
E1
Boot standalone backup
Conversational boot
1 If
Example: show
boot_reset
Command
installed on disk
To execute the show boot_reset command, use the following

syntax:
>>> sh[ow] boot_r[eset]
Return
The following example shows the value of the boot reset variable.
>>> sh boot_r
Return
Result:
BOOT_RESET = ON
450
SHOW
Example:
show config
Command
To execute the show config command, use the following syntax:

>>> sh[ow] conf[ig]
Return
The following is an example of a system configuration.

>>> show config
Result:
DEC 3000 - M300
VPP PAL X5.39-80800101/OSF PAL X1.28-80800201 Built on 30-MAR-1993 09:55:18.29
TCINFO
------
DEVNAM
-----CPU
ASIC
MEM
FEROM
DEVSTAT
-------OK KN16-AA - Vx.x-Syyy-Izzz - sx.x - DECchip 21064 P3.0-150
OK
OK
6
CXT OK
5
NVR
SCC
NI
ISDN
OK
OK
OK
OK
4
SCSI OK
Example:
show device
Command
To execute the show device command, use the following syntax:

>>> sh[ow] dev[ice]
Return
The following example shows the current devices.

>>> show device
Return
Result:
BOOTDEV
------ESA0
DKA300
DKA500
..HOSTID..
ADDR
DEVTYPE NUMBYTES
---------- -------08-00-2B-2F-F8-E6 , TENBT
A/3/0 DISK
426.25MB
A/5/0 DISK
......
A/7
INITR
RM/FX WP DEVNAM
----- -- ------
REV
---
FX
RM
0900
0068
RZ25
RX26
451
SHOW
Example:
show diag_loe
Command
To display the current diag_loe variable setting, use the following

syntax:
>>> sh[ow] diag_l[oe]
Return
The following example shows that the current setting of diag_loe

is OFF.
>>> sh diag_l
Return
Result:
DIAG_LOE = OFF
Example: show
diag_quick
Command
To execute the show diag_quick command, use the following

syntax:
>>> sh[ow] diag_q[uick]
Return
One of the diagnostic settings in the following table is displayed

on the screen.
Diagnostic
Setting
Description
On
Fast testing
Off
Normal testing
The following example shows the selected diagnostic mode.

>>> show diag_quick
Return
Result:
DIAG_QUICK = ON
Example: show
diag_section
Command
To execute the show diag_section command, use the following

syntax:
>>> sh[ow] diag_s[ection]
452
Return
SHOW
The following example shows the mode selected.

>>> sh diag_s
Return
Result:
DIAG_SECTION = 2
Example: show
enable_audit
Command
To execute the show enable_audit command, use the following

syntax:
>>> sh[ow] enable_a[udit]
Return
The following example shows the boot audit trail enabled.

>>> sh enable_a
Return
Result:
ENABLE_AUDIT = ON
Example: show
error Command
To execute the show error command, use the following syntax:

>>> sh[ow] e[rror]
Return
The following example displays the error information.

>>> show error
Return
Result:
??002 SCC 0x0040
?T-ERR-SCC-MODEM - CTS bit Exp = 1 Rec = 0
The status message in this example means that the modem test
expected the CTS bit to be set, but it was clear.
??001 SCC 0x0060
?T-ERR-SCC-Mouse - %x char recvd
The status message in this example means that the response
received from the mouse was less than the number of characters
expected.
453
SHOW
Example:
show ethernet
Command
To execute the show ethernet command, use the following syntax:

>>> sh[ow] et[hernet]
Return
The following example shows the Ethernet address and Ethernet

port.
>>> show ethernet
Return
Result:
ETHERNET = 08-00-2B-2F-F8-E6 , TENBT
Example:
show language
Command
To execute the show command with language variable, use the

following syntax:
>>> sh[ow] l[anguage]
Return
The following example identifies the language as Spanish.

>>> show language
Result:
LANGUAGE = 5
454
Return
SHOW
Example: show
mem Command
To execute the show mem command, use the following syntax:

>>> sh[ow] mem
Return
The following example shows the memory status information.

>>> show mem
Result:
DEC 3000 - M300 Memory: 32 Mbytes
-----------------------------------------BANK #
MEMORY_SIZE
START_ADDRESS
---------------------------0
008 Mbytes
0x00000000
1
008 Mbytes
0x00800000
2
008 Mbytes
0x01000000
3
008 Mbytes
0x01800000
4
000 Mbytes
0x00000000
5
000 Mbytes
0x00000000
6
000 Mbytes
0x00000000
7
000 Mbytes
0x00000000
>>>
In the above example:
Example: show
mop Command
Banks 0,1,2,3 each contain one 8-megabyte SIMM
Banks 4,5,6,7 contain no memory
To execute the show mop command, use the following syntax:

>>> sh[ow] mo[p]
Return
The following example shows that the mop environment has

been selected.
>>> sh mo
Return
455
SHOW
UTC
AccurTDF
BytesRx
BytesTx
FramesRx
FramesTx
McBytsRx
McFrmsRx
FrmDefer
Frm1Coll
FrmMColl
TerXsCol
TerCarCk
TerShCkt
TerOpCkt
TerFRLng
TerNoDef
RerFCSEr
RerFrmEr
RerFrLng
UnknDest
DataOvrn
SyBuffUn
UsBuffUn
HrtBtErr
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
0000000D.5F384CA0
10000000.000186A0
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000014
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
00000000.00000000
MOP = ON
Example: show
radix Command
To execute the show radix command, use the following syntax:

>>> sh[ow] ra[dix]
Return
The following example displays the radix.

>>> show radix
Return
Result:
RADIX = 10
Example:
show secure
Command
To execute the show secure command, use the following syntax:

>>> show secure
Return
The following example displays the console security status.

>>> show secure
456
Return
SHOW
Result:
SECURE = OFF
Example:
show scsi_a
Command
To execute the show scsi_a command, use the following syntax:

>>> sh[ow] scsi_a
Return
The following example shows the SCSI ID for the system is 7.

>>> show scsi_a
Return
Result:
SCSI_A = 7
Example: show
scsi_reset
Command
To execute the show scsi_reset command, use the following

syntax:
>>> sh[ow] scsi_r[eset]
Return
The following example shows that the current value of the SCSI
reset is 4.
>>> show scsi_reset
Return
Result:
SCSI_RESET = 4
Example:
show trigger
Command
To execute the show trigger command, use the following syntax:

>>> sh[ow] t[rigger]
Return
The following example shows the current trigger setting.

>>> show trigger
Return
Result:
TRIGGER = OFF
457
START
START
Starts CPU
The start command is used to set the program counter (PC) and
start the CPU. The command causes the system to exit console
mode and enter program mode.
Format
To execute the start command, use the following syntax:
>>> start {address}
458
Return
TEST
TEST
Diagnostic
Testing
The test command lets you test the entire system, a portion
of the system (or subsystem), or a specific device. If you do not
specify a parameter, the system will test all components.
Format
To execute the test command, use the following syntax:
>>> t[est] [test_device] [optional_parameters]
Parameters
Return
The following table describes the test command parameters:

Parameter
Function
test_device
The name of the device or subsystem to

be tested.
optional_parameters
Optional parameters accepted by a

subsystem test. Refer to Table 415
through Table 420, and Table 422.
CAUTION
If the action performed by a parameter has the potential

of destroying data written on media, you are first
prompted to make sure that you really want to perform
the action. The following prompt is displayed: OK?
459
TEST
The test command, when used with the test_device parameter

and an optional parameter, executes selected diagnostics. The
following parameters specify a device or subsystem to be tested.
A list of available devices in the system can be obtained by
issuing a show config command. Table 411 lists the names of
the devices and subsystems you substitute for [test_device] in the
command line.
Table 411 Test Devices
460
Parameter
Function
asic
Tests the ASIC (application-specific integrated

circuit) subsystem.
cxt
Runs the CXT (graphics) pattern test with the

user verification parameter set.
ferom
Tests to see if the Flash ROM image is correct for

the CPU, and that the expected checksums are
correct.
isdn
mem
Tests the ISDN and audio subsystem.
ni
Verifies that the LANCE chip is operational. The

diagnostic also induces "forced errors" to ensure
functionality.
nvr
Tests NVR (nonvolatile random-access memory),

and specifically ensures the integrity of the
TOY/NVR controller located on the system module.
scc
Tests the SCC (serial communication controller

chip: keyboard, mouse) subsystem, and specifically
the data path to the SCC, and the ability to
operate in asynchronous mode.
scsi
Tests the SCSI subsystem, specifically the

controller chips, SCSI ASIC, SCSI bus, and DMA
path.
tcn
Tests the TURBOchannel option in slot n, that is,

the option installed in either slot 0 or 1. For use
on Model 300/300X/300LX systems.
Performs ECC testing of memory, as well as

detects address and data with faults.
TEST
The following test scsi command parameters specify the

frequently-used SCSI test utilities:
Parameter
Function
Test Requirements
erase
Spins up and erases a

fixed disk.
RZnn disk drive
format
Formats and erases a

diskette.
RX26 removable-media
drive
verify
Verifies that all blocks

on a fixed disk can be
read.
RZnn disk drive
461
TEST
Erase Disk
Utility Example
The following example erases a fixed disk. Enter the following

command and answer the question.
>>> t[est] scsi erase
Return
The following example displays the questions to which you must

respond:
>>> t scsi erase
Return
SCSI_id(0-7)>>> 3 Return
SCSI_lun(0-7)>>> 0 Return )
SCSI HD_DSK_ERAS_UTIL
DKA300 OK? OK Return
.......................................................
SCSI-bb-repl 0
SCSI-util_succ
OK
>>>
Table 412 explains the action required by each prompt.
Table 412 Erase Disk Utility Prompts
462
Utility Prompts With...
Action
SCSI_id(0-7)>>>
SCSI_lun(0-7)>>>
DKA100 OK?
Select SCSI ID number <07:00>

Select logical unit number <07:00>
Answer OK if device is correct
TEST
Diskette
Formatter
Utility Example
The Diskette Formatter Utility formats and erases a diskette.

To format a diskette in a device specified, for example, as
dka500:
1. Place the diskette in the drive.
2. Enter the following command, answering the questions that
are displayed:
>>> t[est] scsi format
Return
SCSI_lun(0-7)>>> 0 Return
SCSI FLP_FMT_UTIL
DKA500 OK? OK Return
SCSI-util_succ
OK
Table 413 Diskette Formatter Utility Prompts
Action
SCSI_id(0-7)>>>
SCSI_lun(0-7)>>>

CAUTION
Once the Diskette Formatter Utility is started, do not

terminate the action or halt the machine. This will
corrupt the device being tested, and formatting will have
to be performed again.
463
TEST
Verify Disk
Utility Example
The Disk Verify Utility verifies that all blocks on a disk can be
read. To verify a disk, enter the following command and answer
the questions that are displayed:
>>> test scsi verify
Return
The following example verifies device dka500.

>>> t scsi verify
Return
SCSI_lun(0-7)>>> 0 Return
DKA500 OK ? OK Return
SCSI_DSK_VER_UTIL
SCSI-util_succ
OK
>>>
Table 414 Verify Utility Prompts
464
Action
SCSI_id(0-7)>>>
SCSI_lun(0-7)>>>

TEST
Example: test
Command
The following example runs all available diagnostics, except

TURBOchannel diagnostics on the Model 300L system.
>>> test
Return
The display on your screen may show some of the following tests:
T-STS-ASIC - OK
T-STS-MEM - Current Test Parameters
T-STS-MEM - lo_addr = 00200000 init_mem = ON test_bad_pages = OFF
T-STS-MEM - hi-addr = 02000000 stop_on_err = ON
max_retries = 0
T-STS-MEM - Fill mem Wr AAAAAAAA 01800000
T-STS-MEM - Cell Test: FWD RD WR 55555555
T-STS-MEM - Addr Test: Waiting 10 seconds to test refresh
T-STS-MEM - OK
T-STS-NVR - ASSURE_CLOCK_IS_TICKING test
T-STS-SCC - DMA test
T-STS-SCC - LK401 test
T-STS-SCC - OK
T-STS-NI - Ext Lpbk test -
465
TEST
Example: test
asic Command
Diagnostic testing of the application-specific integrated circuit

(ASIC) is performed when the system is in console mode. All
reported errors contain a hexadecimal longword of data, and
the FRU code 001 to identify the failing component. Table 415
describes each ASIC test and the mode in which it is run.
Table 415 ASIC Diagnostic Subtests
Test Name
Description
Mode
Test
Requirements
coreio
Tests the CORE I/O ASIC

registers
Console
None
fp
Tests the floating point

registers
Console
None
init
Initializes the
TURBOchannel interface
registers and core ASIC
registers
Console
None
tci
Tests the TURBOchannel

interface registers
Console
None
Lists subtests
Console
Service
None
The following is the command format for the ASIC test:

>>> t[est] asic test_name
Result (on error):
?? 001 ASIC xxxxxxxx
466
Return
TEST
Example:
test ferom
Command
Diagnostic testing of the flash ROM (FEROM) is performed when

the system is in console mode. All reported errors contain a
hexadecimal longword of data, and the FRU code 001 to identify
the failing component. Table 416 describes each FEROM test
and the mode in which it is run.
Table 416 FEROM Diagnostic Subtests
Example: test
mem Command
Test Name
Description
Mode
Test
Requirements
chksum
Verifies that the calculated

checksums equals the
checksum in the ROM.
Console
None
cpu
Flash ROM image must

correspond to CPU.
Console
None
Diagnostic testing of system memory detects address and data

that is stuck at faults, as well as performing ECC testing of
memory. Table 417 lists and describes the parameters. All
reported errors contain a hexadecimal longword of data, and the
FRU code 8yz to help locate the failing memory module.
Table 417 describes each memory test and the mode in which it
is run. Chapter 8 contains additional information about testing
memory.
467
TEST
Table 417 Memory Diagnostic Subtests
Test Name
Description
Mode
Test
Requirements
addr
Detects addresses stuck at

faults
Console
None
all
bits
Performs all tests
Console
None
Detects marching ones in

a field of zeros; single-bit
parity testing, every bit in
each longword
Console
None
cell
Detects data stuck at

faults
Console
None
init
Initializes all memory to

zeros
Console
None
llsc
Tests the load-locked/store

conditional
Console
MOP
must be
set OFF
Lists subtests and options
Console
Service
None
The following is the command format for the memory test:

>>> t[est] mem test_name
Return
Result (on error):

?? 8yz MEM xxxxxxxx
Example: test
nvr Command
468
Diagnostic testing of the nonvolatile RAM (NVR) tests the

TOY/NVR controller that is located on the system module.
Table 418 lists and describes the parameters. All reported
errors contain a hexadecimal longword of data, and the FRU
code 001 to help locate the failing component. Table 418
describes each NVR test and the mode in which it is run.
TEST
Table 418 NVR Diagnostic Subtests
Test Name
Description
Mode
Test
Requirements
cpu
init
Tests the CPU
Console
None
Initializes the interval

timer registers
Console
None
interrupt
nvr
toy
Tests the interval timer
Console
None
Tests nonvolatile RAM
Console
None
Tests the TOY (time of

year) clock
Console
None
Lists subtests and options
Console
Service
None
The following is the command format for the NVR test:

>>> t[est] nvr test_name
Return
Result (on error):

?? 001 NVR xxxxxxxx
Example: test
scc Command
Diagnostic testing of the serial communications controller (SCC)

tests the functionality of the following:
Data path to the SCC
Ability to operate in asynchronous mode
Data path from SCC to connectors on the back panel of the

system unit
DMA using the RS232 port
Keyboard/mouse port
All reported errors contain a hexadecimal longword of data,

and the FRU code 001 to help locate the failing component.
Table 419 describes each SCC test and the mode in which it is
run.
469
TEST
Table 419 SCC Diagnostic Subtests
init
Performs a reset test on

SCC controller
Console
Service
None
polled
Tests polled I/O
Console
Service
None
interrupt
Tests interrupt driven

I/O
Console
Service
None
dma
Tests DMA transfers
Console
Service
None
LK401
Tests for presence of

keyboard
Power-up
Console
Keyboard
mouse
Tests for presence of

mouse
Power-up
Console
Mouse
modem
Tests modem control

signals
Power-up
Console
Loopback
Lists subtests
Console
Service
None
The following is the command format for the SCC test:

>>> t[est] scc test_name
Return
Possible results (on error):

?? 001 SCC xxxxxxxx
?? 003 SCC xxxxxxxx
?? 004 SCC xxxxxxxx
Example: test
ni Command
470
The Network Interconnect (NI) diagnostic test verifies that

the LANCE chip is operational. The NI listener is enabled at
startup; that is, it executes automatically with no intervention.
It may be disabled by typing set mop 0. All reported errors
contain a hexadecimal longword of data, and the FRU code 001
to help locate the failing component. Table 420 describes each
NI test and the mode in which it is run.
TEST
Table 420 NI Diagnostic Subtests
Test Name
Description
Mode
Test
Requirements
collision
Tests internal loopback

with collision
Service
Loopback
crc

with CRC check
Service
Loopback
dma_init
Tests LANCE
initialization and DMA
Console
Service
Loopback
ext_lpbk
Tests the external

loopback
Console
Service
Loopback
filter

with address filter
checking
Service
Loopback
ilpbk

and initialization
Console
Service
Loopback
init
Initializes the LANCE

chip and NI port
Console
Service
Loopback
interrupt

with interrupts
Console
Service
Loopback
nar
Tests network address

ROM
Console
Service
Loopback
register
Tests LANCE registers
Console
Service
Loopback
rx_miss_buff Tests internal loopback
Service
Loopback
with MISS error
tx_buff

with transmit buffer
error
Service
Loopback
Lists subtests
Console
Service
None
The following is the command format for the NI test:

>>> t[est] ni test_name
Return
471
TEST
If an external loopback is not present, the following message is

displayed:
T-STS-NI - Ext lpbk test
? T-ERR-NI - Exte Lpbk test
T-ERR-NI - Err = ac
?? 000 NI0x00f2
Example: test
tc Command
The TURBOchannel (TC) diagnostic test tests TURBOchannel

options in slots 0 and 1 using MIPS emulator scripts.
In addition to diagnostic testing, the MIPS emulator performs
these additional tasks on a TURBOchannel option:
Initializes the option
Displays option configuration
Runs the console on a TURBOchannel option
Boots the operating system using a TURBOchannel option

Note
Not all TURBOchannel options can be successfully tested
with this command. Refer to your option installation
manual for additional information.
The following is the command format for the TURBOchannel

self-test:
>>> t[est] device_name
Return
where:
device_name is the TURBOchannel device name in the form

of TCn, where n is the slot number of the TURBOchannel
device you wish to test.
To test a device connected to slot 2, enter the following command:

>>> test tc2
472
TEST
On power-up, the script pst-q is run unless the environment

variable diag_quick is set to on. With diag_quick set to ON,
no TURBOchannel testing is done. When the enironment
variable diag_section is equal to 1 or 2, the pst-m script is run.
Graphics options are an exception to this rule, since the cnsltest
script is run as part of console determination.
The following command format should be used to execute a
selected test on a TURBOchannel option.
>>> test device_name test_name
where device_name is the TURBOchannel device name and
test_name is the name of the test you want to run.
The following example lists the contents of the option ROM and
the available scripts for the option in TURBOchannel slot 1.
Object scripts are not executable. All items listed are not to be
used as a script_name.
>>> t[est] tc1 ls
Return
If an asterisk (*) is at the end of a script, then the object script

will fail if selected. If test_name contains a slash or hyphen,
then test_name should be enclosed in double quotes so that the
command line parser treats it as a single argument.
The following example runs a diagnostic script on the option
installed in TURBOchannel slot 1.
>>> t[est] tc1 script_name
Return
The following example executes default test scripts on the option

installed in TURBOchannel slot 1.
>>> t[est] tc1
Return
The following example executes a single test script.

>>> t[est] tc1 pst-m
Return
473
TEST
Table 421 TC Diagnostic Subtests

Test
Requirements
Test Name
Description
Mode
cnfg
Displays
configuration on
TC option slot
Console
Service
TC option
init
Initializes option in
TURBOchannel slot
Console
Service
TC option
initc
Initializes console
device
Console
Service
TC option
putc
Outputs a character
Console
Service
TC option
cat
script_name
script
script_name
Lists content of a
script
Power-up
Console
TC option
Runs the script

script_name on
the option in the
TURBOchannel slot
Power-up
Console
TC option
Lists subtests
Console
Service
None
The following example initializes TURBOchannel option 1.

>>> t[est] tc1 init
474
Return
TEST
Example: test
scsi Command
SCSI diagnostic testing verifies the following:
SCSI controller chip
SCSI ASIC
SCSI bus
DMA path in physical and virtual modes
Testing in console mode exercises the data paths between the:
CPU and the TURBOchannel interface
TURBOchannel interface and the SCSI ASIC
SCSI ASIC and SCSI controllers
SCSI controllers and the SCSI bus
All reported errors contain a hexadecimal longword of data, and

the FRU code 001 or 1TL to help locate the failing component.
Chapter 8 contains additional FRU code information. Table 422
describes each SCSI test and the mode in which it is run.
Table 422 SCSI Diagnostic Subtests
Test Requirements
Test Name
Description
Mode
asic
Tests the SCSI ASIC

registers
Console
Service
SCSI
terminator
or device
device2
Tests SCSI devices
Service
SCSI
terminator,
media in
device
erase
Specifies the Hard

Disk Eraser Utility
Console
Service
RZnn hard
disk
format
Specifies the Floppy

Formatter Utility
Console
Service
RX26
removablemedia drive
2 Removable-media
drive must have media installed before testing.
475
TEST
Table 422 (Cont.) SCSI Diagnostic Subtests

Test Requirements
Test Name
Description
Mode
init
Initializes the drive
Console
Service
SCSI device
logic
Console
Service
SCSI
terminator,
device
register1
Tests SCSI
controller registers
Console
Service
SCSI
terminator,
device
transfer
Tests data transfers

across the SCSI bus
Console
Service
SCSI device
verify
Specifies the Disk

Verifier Utility
Console
Service
RZnn hard
disk
Lists subtests and

options
Console
Service
None
interrupt1 Tests the interrupt
1 Does
not require the presence of a device on the SCSI bus.
The following is the format of the test scsi command:

>>> t[est] scsi test_name
Result (on error):
?? 001 SCSI xxxxxxxx
476
Return
TEST
Example: test
isdn Command
The ISDN diagnostic tests test both ISDN and audio

functionality. Table 423 describes each ISDN test and the
mode in which it is run.
Table 423 ISDN Diagnostic Subtests
Test
Requirements
Test Name
Description
Mode
a_loop
Tests analog loopback.
Console
Service
None
d_loop
Tests internal digital

audio loopback.
Service
None
DMA
Tests DMA.
Console
Service
None
init
Initialize ISDN chip.
Console
Service
None
int
Interrupt test.
Console
Service
None
playback
Plays back the recorded

message.
Service
Handset
record
Prompts you to speak

into handset. A short
message is saved in
memory and then
played back through
the speaker.
Service
Handset
reg
Tests internal registers.
Console
Service
None
repeat
Allows you to speak

into the handset
and hear your speech
repeated.
Service
Handset
tone
?
Tests audio output.
Service
Handset
Lists subtests.
Console
Service
None
The following is the command format for the ISDN test:

>>> t[est] isdn test_name
Return
477
TEST
Result (on error):

?? 001 ISDN xxxxxxxx
The following example tests the audio record feature:
>>> test isdn record
Example: test
cxt Command
Return
Graphics (CXT) diagnostic testing is performed when the system

is in power-up mode, e.g., when power is first applied to the
system. A graphics pattern test is displayed. All reported errors
contain a hexadecimal longword of data, and the FRU code 001
to identify the failing component.
Table 424 CXT Diagnostic Subtests
Test Name
Description
Mode
Test
Requirements
patt-v
Runs the CXT (graphics)

pattern test
Power-up
None
The following is the command format for the CXT test:

>>> t[est] cxt test_name
Result (on error):
?? 001 CXT xxxxxxxx
478
Return
5
Using the Password Security Feature
Chapter Overview
In This Chapter
This chapter presents information on the following topics:
Secure Console Commands
Invoking the Password Security Feature
Purpose of
the Security
Feature
If the password security feature is not used, whenever a user

enters console mode, he or she can use all of the privileged
console commands, such as halt, set, deposit, and boot. The
password security feature allows you to restrict access to these
key console mode functions.
Before You Use

the Security
Feature
Before making your system secure, determine who will have

access to privileged commands once you enable the security
feature. Whoever requires privileged access to the system will
need to know the password that you enter.
If your operating system is running, use the shutdown
procedures in your operating system documentation to shut
it down.
51

Privileged
Commands
Once you invoke the password security feature and change the
secure system jumper, privileged console commands become
protected. That is, you can access these commands only if you
log in to the system with the login command at the console
prompt (>>>).
In general, any commands that modify memory and registers,
or that transfer CPU control from the console monitor to
another program, such as boot (with parameters) or start,
are considered privileged commands. Once you have access to
privileged commands, access continues until you disable the
password. (See the section entitled Disable the Password in this
chapter.)
List of
Commands
Table 51 lists both privileged and non-privileged console

commands.
Table 51 Console Command Access
Privileged Commands
Non-privileged Commands
boot (with parameters)

deposit
boot (without parameters)

login (to allow password entry to
the privileged state)
52
examine
continue (if you inadvertently push

the halt button, this command
lets you continue operations in a
non-privileged mode)
halt
initialize
repeat
set
show
start
test
help

Steps to
Making the
System Secure
Making your DEC 3000 Model 300 Series AXP system secure
requires software and hardware tasks. Table 52 describes the
steps required to secure your system.
Table 52 Steps to Making the System Secure
Step
Description
Enter a password
Enable security
Move the secure system jumper
Antistatic
Precautions
Do not perform any tasks inside the system unit without

attaching the antistatic wrist strap to your wrist and the system.
Refer to the section entitled CAUTION: Static Discharge in
Chapter 2.
Enter a New
Password
Your system arrives from the factory without a password. The

password you enter must be a character string of exactly 16
hexadecimal characters (0 through 9 and A through F). To enter
a password on your system, enter the commands shown in
Table 53 starting at the console prompt (>>>).
Table 53 Entering a Password
Enter this command:
System responds...
>>> set password

PSWD1> new_password
PSWD2> new_password
PSWD1>
PSWD2>
>>>
Return
Return
As you enter the password, what you type does not display, or
echo, on the screen. If the two passwords you entered match,
your password is preserved in nonvolatile memory, which means
that the system saves your password value even when the
system unit is turned off.
53
If the two passwords you enter do not match, the console displays
the following error message:
? 30 ILL PSWD
In this case, enter the set password command again as described
above.
Note Your
Password
Be sure to make a note of your password and store it in a secure

place. If you forget your console mode password, refer to Erase
The Password, later in this chapter, or call your Digital service
representative.
Enable the
Password
Security
Feature
Once you have entered and confirmed your password, check to be

sure the secure parameter is set to on, as follows:
>>> show secure
Return
SECURE = OFF
If, as in the example above, the password security feature is not
enabled, set it to on, as follows:
>>> set secure on
Return
SECURE = ON
Before You
Move the
Secure System
Jumper
54
After entering a password and enabling the secure parameter,

you must move the secure system jumper, on the system module,
to the enable position to complete the security feature.
Before you move the secure system jumper, be sure you complete
Step
Action
Halt the system, if necessary, to display the console

prompt (>>>). (See Chapter 2.)
Turn off your equipment. (See Chapter 2.)
Remove the system unit cover. (See Figure 26).
Attach the antistatic wrist strap.
Locate the
Secure System
Jumper
Figure 51 shows the secure system jumper, labeled W3 on

the system module. In the enabled position, the jumper is
attached to pins 1 and 2, counting from left to right. In the
default disabled position, the jumper is attached to pins 2 and 3,
counting from left to right.
Figure 51 The Secure System Jumper
MLO-010747
Enabled
Disabled
Move the
Jumper
To use the password security feature, move the jumper to the

enabled position, pins 1 and 2, using tweezers or another small
tool.
55
Restore the
System
Log In to the
System
After you move the jumper, complete the following steps to

restore the system:
Step
Action
Replace the system unit cover. (See Figure 231.)
Turn on the system. (See Chapter 2.)
If your system does not halt automatically, press the

halt button to display the console prompt (>>>). (See
Chapter 2.) From this point on, you will need to use the
login command, described in the next section, to access
privileged console commands.
After entering the password, enabling it, and then changing

the secure system jumper on the system module, you must use
the login command to access privileged console commands, as
Table 54 describes.
Table 54 Entering a Login Command
Enter this command:
System responds...
>>> login Return

PSWD0> password
PSWD0>
>>>
Return
The variable password is the password you issued with the set
password command. If you enter the password incorrectly, the
system responds with this message:
? 30 ILL PSWD
In this case, enter the login command again as described in
Table 54.
56

Change the
Password
To change the password, enter the set password command, your

old password, and your new password as shown in Table 55.
The password must be exactly 16 hexadecimal characters, 0
through 9 and A through F.
Table 55 Changing a Password
Enter the following:
The system responds...
>>> set password

PSWD0> old_password Return
PSWD1> new_password Return
PSWD2> new_password Return
PSWD0>
PSWD1>
PSWD2>
>>>
If the two new passwords you enter are the same, your password
is changed.
If the two passwords do not match, the system displays:
? 30 ILL PSWD
Try the procedure again.
Erase The
Password
You can erase the current password without knowing what it is.
Therefore, if you forget your password, you may want to erase
it and enter a new one. To erase the current password, enter
the deposit command with the exact parameters shown in the
following example. There is no system response to this deposit
command.
>>> deposit /u/q-n:1 1A0200088 0
Return
57
Caution
When you turn on the system, the firmware is loaded
into and executed from memory. If you did not disable
the flash ROM update jumper, be aware that using
the deposit command to place a value in a location of
memory containing the actual console firmware could
hang the system. To restart the system, turn the power
off and than back on.
Once your password is erased, you can enter a new password as

explained in the section Enter a New Password earlier in this
chapter.
Disable the
Password
To disable the password security feature, you must enter the

login command and your password. Then enter the following
command at the console prompt:
>>> set secure 0
Return
SECURE = OFF
If you then try to log in, the following message is displayed:
?31 PASWD NOTEN
58
6
Using an Alternate Console Device
Chapter Overview
Introduction
The alternate console feature of your system lets you direct

console input and output from a graphics monitor to another
device, such as a terminal or printer.
In This Chapter
This chapter covers the following topic:
Setting the Alternate Console Feature
61

When to Use
the Alternate
Console
Feature
Task Overview
The following are possible reasons for using an alternate console:
You cannot display output on your graphics monitor because

it is not working properly.
You want to save a hard copy of the console screen display on

a printer.
Table 61 describes the steps for using the alternate console

feature.
Table 61 Using the Alternate Console
62
Step
Action
Connect a terminal or printer to the synchronous/

asynchronous communications RS-232 port on the back of
the system unit.
Detach your keyboard or change the alternate console

jumper.
Redirect output to the alternate console.
Connect a
Terminal or
Printer
To connect a terminal or printer as an alternate console device,

connect the terminal or printer cable to the synchronous/
asynchronous communications port on the system unit, shown in
Figure 61.
Figure 61 Connecting the Alternate Console to the System
ISD
MLO-009790
63
Alternate
Console/Printer
Port Settings
The alternate console/printer port on the back of the system unit

is set at the factory to the parameter settings listed in Table 62.
These settings cannot be changed.
Table 62 Alternate Console/Printer Port Parameters
Disconnect the
Keyboard
Parameter
Setting
Baud rate
9600
Parity
None
Stop bit
Bits per character
To switch to the alternate console by removing the keyboard,

follow these steps:
Step
Action
Wait 10 to 15 seconds.
Disconnect the keyboard/mouse extension cable from the

back of the system unit.
Turn on the system.

Output is automatically transferred to the alternate
console device. In most cases, this is a terminal, which
has its own keyboard.
If you want to use the graphics terminal as well as the

alternate console device, reconnect the keyboard/mouse
extension cable.
If you are running the operating system, however, you
cannot change from one console to the other. You can do
this only from console mode (>>>).
1 If
you were using a graphics monitor to display console output before you
connected an alternate console device, you must restart your system to redirect
console output. If you do not restart your system, the console output will not
display on the terminal or printer you connected.
Note that the system automatically displays its configuration

every time it is turned on.
64
Or, Change
the Alternate
Console
Jumper
To switch to the alternate console by changing the alternate

console jumper, remove the system unit cover (see Chapter 2),
and reset the jumper, shown in Figure 62 and labeled W2.
Note
Do not perform any tasks inside the system unit without
attaching the antistatic wrist strap to your wrist and to
the system, as shown in Figure 62.
By setting the jumper, you can select either of the following ports
for console output:
The graphics port: pins 1 and 2 (default)
The serial port for an alternate console device: pins 2 and 3
(Pins 3 and 4 are reserved.)

Figure 62 Alternate Console Jumper
MLO-009789
65
Restart the
System
After you reset the jumper, you must restart the system to
redirect the console output. The system automatically displays
the show config display. From here on, the system will always
come up on the alternate console when you start it.
To Access
Console Output
via the Network
Console output can also be accessed via the network. Thus, you
can remotely troubleshoot the system or use a remote console
when no local console is available.
Note that some console tests and commands, such as the memory
diagnostic, cause the network connection to be terminated
because the commands use the network device, or they cause a
connection timeout at the remote node. If this occurs, you will
have to turn the system off and then back on.
To access console output via the network:
66
Step
Action
Obtain the hardware Ethernet address of the system.
Obtain access to an operating system on the same

Ethernet segment as the DEC 3000 Model 300 Series
AXP System (the systems cannot be separated by a bridge
or router).
Set the following system parameters:
A console password
set mop, set trigger
To connect to the console:

Step
Action
Log into the user account (no special privileges are

required).
Type the following commands for OpenVMS AXP only:

$ mcr ncp
Return
;Enters the Network Control Program (NCP)
NCP> show known circuits
Return
;Shows available circuits

;you can connect through
NCP> connect via circuit_name service password xxxx

physical address 08-00-2B-XX-XX-XX Return
>>> Ctrl/D
NCP> exit
$ lo
Return
Return
Return
;Disconnects console
;Exits NCP
;Logs off the system
67
7
Troubleshooting by Visual Inspection
Chapter Overview
Introduction
Though your DEC 3000 Model 300 series system is a highquality, thoroughly tested product, it is also an electrical device
that may on occasion exhibit a problem. The tables in this
chapter can help you quickly identify the problem with a visual
check, and possibly fix the problem. If you cannot identify the
problem using these tables, try the more advanced procedures
described in Chapter 8.
This chapter also describes how to clean the system.
Before You
Begin
Before you proceed with this chapter:

1. Verify the problem as follows:
a. Turn off all expansion boxes.
b. Turn off the monitor and all peripheral devices, such as
printers and modems.
c.
d. Check that all cables and cords are correctly connected at

both ends.
e.
Turn the equipment back on in the following order:

1. Any storage expansion box
2. Printer
3. Monitor
4. System unit
71
Chapter Overview
2. Adjust the brightness and contrast of your monitor.

If your system is still not working correctly after completing the
previous steps to verify the problem, use the troubleshooting
tables to identify the problem.
If the power-up graphics display appears, followed by the console
prompt (>>>), try starting your operating system.
Using the Troubleshooting Tables

Introduction
Use the information in this section to help locate system

problems. The following tables do not identify all possible
problems with the system, nor do the actions suggested remedy
all problems, but they are useful for many common problems.
To use the troubleshooting tables, follow these steps:
1. Find the problem your system is having in the Symptom
column in the following tables.
2. Check the conditions for that symptom in the Possible Cause
column.
3. Follow the advice in the Corrective Action column.
72
System
Problems
If you are having trouble with your entire system, locate the
problem in Table 71.
Table 71 Preliminary Troubleshooting of System Problems

Symptom
Possible Cause
Corrective Action
Window display does not

appear on the screen.
(System does not boot.)
Your software is not installed.
See your software documentation

for installation instructions.
System startup has failed. Check
the status of the diagnostic display
lights, described in Chapter 8, or
refer to the Service Guide or your
Digital service representative.
Power indicator light is off

and fans are not running.
Power cord is not connected.
Check the power cord connections

at both ends.
Defective power supply.

representative.
Power indicator light is

off, but fans are running.

representative.
Power-up graphics display

does not appear after 1
minute and the diagnostic
display lights display
.
Monitor is not turned on.
Turn on the monitor. See Chapter 8

for additional corrective actions.
Power-up graphics display

does not appear and the
diagnostic display lights
display .
SROM jumper setting is

incorrect.

representative.
No diagnostic display
lights after startup.
Possible defective system

module, or defective cable.
See Chapter 2 for information on

the location of the system module
and cables. Reseat the system
module, ensure that all cables have
a tight fit in their connectors, and
restart the system.
Startup display contains

question marks or an error
message.
Possible system error.

Loose cable connections.
Refer to Chapter 4 for information

on running diagnostic tests.
73
Table 71 (Cont.) Preliminary Troubleshooting of System Problems

Symptom
Possible Cause
Corrective Action
If a ?? appears next to NI, the
Ethernet cable may be loose.
If a ?? appears next to SCC, then
the keyboard and mouse cables
may be loose in the keyboard/
mouse connector block, or the
keyboard/mouse connector block
cable connector may not be firmly
attached to the system unit.
System does not boot at

startup.
74
Software is not installed.
Install the system software. Refer

to the software documentation for
installation instructions.
Default recovery action is set

to halt.
Refer to Chapter 4 to change the

default recovery action to boot the
system from the system disk.
Incorrect boot device was

specified.
Change the default boot device

(bootdef_dev) parameter, explained
in Chapter 4.
Boot device is not properly

configured.
Enter a show device command as

Chapter 4 describes and check to
see that all devices are configured
properly. If not, check the SCSI
IDs and the SCSI cables. Refer to
Chapter 2.
Software problem.
Refer to your operating system

documentation. Call your Digital
service representative.
Monitor
Problems
If you are having trouble with your monitor, locate the problem
in Table 72.
Table 72 Troubleshooting Monitor Problems

Symptom
Possible Cause
Corrective Action
No display appears on the

monitor screen.
Monitor is not turned on.
Check that the monitor on/off switch

is on. Check that the monitor power
cord is connected at both ends.
Wall socket may not be

operative.
Try a different wall socket, or try

an electrical device that you know
works in the wall socket.
Contrast and brightness

controls are set too low to
see the screen display.
Adjust the contrast and brightness

controls. Refer to the monitor guide
for more information.
System module or graphics

board failure.
Refer to Chapter 4 for information

on running diagnostic tests.
Monitor video cable is not

connected.
Check that the monitor cable is

connected at both ends.
If the problem persists, contact your
Display is distorted.
System did not pass startup

test.
Refer to Chapter 4 and Chapter 8 for

information on running diagnostic
tests or contact your Digital service
representative.
Monitor is defective.

representative.
Your color monitor has six

connectors, three marked
Video In, and three marked
Video Out.
Ensure that the monitor video cable

is connected to the three Video In
connectors.
75
Mouse/Tablet
Problems
If you are having trouble with your mouse or other pointing

device, locate the problem in Table 73.
Table 73 Troubleshooting Mouse/Tablet Problems

Symptom
Possible Cause
Corrective Action
Mouse or optional tablet

pointer does not appear on
screen, or monitor does not
respond to pointing device
commands.
Ctrl/F3 was pressed by

mistake, and system pointer
mode is off.
Press Ctrl/F3 again to restart

the pointer mode.
System boots operating

system, but mouse or optional
tablet pointer does not appear
on the screen. Or, monitor
does not respond to pointing
device commands.
Pointing device cable is

installed incorrectly or is
loose.
Turn off the system. Unplug

and then install the cable. Turn
on the system.
Pointing device is faulty.
Replace the pointing device.
The system is in console

mode ( >>> ); no pointer
appears on the screen.
Correct condition. No action

necessary.
Change the system to program
mode by entering boot at the
console prompt ( >>> ).
76
Keyboard
Problems
If you are having trouble with your keyboard, locate the problem
in Table 74.
Table 74 Troubleshooting Keyboard Problems

Symptom
Possible Cause
Corrective Action
Keys do not work.
Hold Screen key is active.

Hold Screen light is on.
Press the Hold Screen key to

release hold on screen.
Keyboard cable is loose or not

connected.
Check the keyboard cable at

both ends.
Keyboard has failed.
Replace the keyboard. If the

problem persists, contact your
SCSI Device
Problems
If you are having trouble with a SCSI device, such as an internal

drive, or an expansion box, locate the problem in Table 75.
Table 75 Troubleshooting SCSI Device Problems

Symptom
Possible Cause
Corrective Action
An installed drive does not

work or is not recognized by
the system.
Two SCSI identifiers are set

to the same number.
Enter the show device

command as Chapter 4
describes. If a drive is not
recognized, reset each SCSI ID
to a unique number.
You turned on the system

unit before you turned on
your expansion box.
Turn off the entire system; turn

equipment back on beginning
with the expansion box.
Loose cables.
Check to make sure all cables

are connected.
Defective drive.
Refer to Chapter 4 for

information on running
diagnostic tests.
A problem exists with the

fixed disk.

diagnostic tests.
Software does not boot from

the fixed disk drive.
77
Table 75 (Cont.) Troubleshooting SCSI Device Problems

Symptom
Software installed in the

diskette drive does not work,
or a diskette read or write
error message is displayed.
Network
Problems
Possible Cause
Corrective Action
Default boot device is set

incorrectly.
See Chapter 4 to set or change

the default boot device.
Recovery action may be set to

halt.
See Chapter 4 to change the

default recovery action.
A problem exists with the

software (if installed) on the
fixed disk.
Refer to your software

documentation for help.
No diskette is in the diskette

drive.
Insert a software diskette. See

your software documentation.
Diskette was inserted

incorrectly.
Check that the write-protect

notch on the diskette is to your
left when you insert the diskette
and that the label is up.
Diskette is damaged or does

not contain software.
Try another diskette that

contains software.
Two SCSI identifiers are set

to the same number.
Reset each SCSI ID to a unique

number.
If you are having trouble with your network, locate the problem
in Table 76.
Table 76 Troubleshooting Network Problems

Symptom
Possible Cause
Corrective Action
NI error message is displayed

when verifying Ethernet.1
No Twisted-pair cable was

installed.
Attach a Twisted-pair cable.
Ethernet cable connection is

loose.
Check that all connections

on the Ethernet segment are
secure.
1 After
you solve an NI problem, type test ni and press the Return key. This either clears the error or
displays a message to let you know the problem still exists.
78
Table 76 (Cont.) Troubleshooting Network Problems

Symptom
Possible Cause
Corrective Action
Cannot boot from the

network.
Local network problem.
Problem is most likely caused by

the customers server system or
the network.
Defective NI interface.

diagnostic tests.
Network connection
If you are using an AUI or

ThinWire adapter to convert
your network connection from
10BASE-T to another network
protocol, turn off the heartbeat
in the network transceiver
(DELNI) to eliminate the
problem, or contact your Digital
service representative.
Data transfer problems.
Table 77 Troubleshooting Audio Problems

Symptom
Possible Cause
Corrective Action
No audio tones from the

system when it is turned on.
Defective sound chip.

diagnostic tests.
79
Cleaning Your System
Cleaning Your System

How to Clean
the System Unit
In some cases a problem with your system may be as simple as

dust or spilled liquid.
To clean the system unit:
1. Clean your system unit regularly by wiping dust and
particles from it with a soft cloth.
2. If you inadvertently spill liquid inside the unit, turn off the
system and contact your Digital Service representative.
How to Clean
the Keyboard
To clean the keyboard:

1. Disconnect the keyboard from the system unit and clean with
a soft cloth.
2. If you spill water on it, wipe the excess off immediately, turn
the keyboard over to drain, and let it dry for several hours
before you reconnect it.
How to Clean
the Mouse
To clean the mouse:

1. Remove the cover plate.
2. Remove the rubber ball from the mouse unit, clean with
lukewarm water, and dry off.
3. Return the rubber ball to the mouse unit.
710
8
Advanced Diagnostics
Chapter Overview
Introduction
This chapter describes more detailed troubleshooting procedures.

During power-up, diagnostic error reporting is done in three
stages:
1. Preliminary initialization, and a test that executes the serial
ROM (SROM) code.
2. Main console power-up and self-tests.
3. More extensive tests the user can run from the main console,
using the test command. (See Chapter 4).
Before You
Begin
Before you proceed with this chapter:

1. Be sure you have gone through the visual inspection
procedures described in Chapter 7.
2. Record the following information on the Handling Problems
Worksheet at the end of this chapter:
The serial number and model number of your system.

The numbers are printed on a label located on the back
of the system above the monitor connector.
The status of your system, using the checklist on the

Handling Problems Worksheet.
The status of the internal diagnostic light display

pattern.
81

Power-up
Problems
When you turn on the system, the SROM (serial ROM) code
performs the following preliminary diagnostic tests:
Memory sizing
I/O
Cache
If no fatal errors are encountered, the SROM code loads the

main console firmware from the flash ROM into main memory.
If the system stops executing because of a fatal error before it
reaches main console mode, messages will not be displayed on
your screen. However, you may be able to determine the problem
by examining the diagnostic display lights (light-emitting diodes,
referred to as LEDs, and described in the next section).
Location of
Diagnostic
Display Lights
82
Diagnostic display lights are the eight red lights located inside
the system unit.
Figure 81 shows the location of these LEDs in the system. You
should be able to read them through the air vents on the side of
the system unit cover without removing the cover. If you have
trouble seeing the lights, however, remove the system unit cover,
as described in Chapter 2.
Figure 81 Position of Diagnostic Display Lights
3 2 1 0
MLO-009795
Display Light
Patterns
When you power up the system, all lights come on and

flash through a sequence of patterns, which are binary
representations of the hexadecimal codes. If a problem is
detected during system power-up, the lights are lit in a
pattern that indicates either the current system status or a
problem.
When power-up tests have completed successfully and the

system is at console mode (>>>), the lights are lit in the
following binary pattern:
on on off on
7 6 5 4
on on off on
3 2 1 0
[OR]

In hexadecimal code, this pattern is DD, where the first D

refers to the left set of four lights; the second D refers to the
right set of four lights.
When the operating system is running, all diagnostic lights

should be off.
Refer to DEC 3000 Model 300 Series AXP Service Guide for
a complete listing of hexadecimal codes, their binary (LED)
equivalent, and their meaning.
83
Correcting the
Problem
If the system stops before successful completion of the

preliminary tests, the lights display other patterns. To correct
the problem, check to see that all:
Modules inside the system unit are seated firmly
Cables are securely connected to the correct ports
Power cables are plugged into the appropriate outlet
Power switches are on
If these actions do not correct the problem, record the LED

patterns on the appropriate section of the Handling Problems
Worksheet at the end of this chapter and call your Digital service
representative.
Post-Powerup
LEDs
Even after the console firmware is loaded, the system may stop
executing before it is able to display messages on your screen.
This may happen because not all SROM tests pass (this displays
LED codes ff through f0, and 20).
Table 81 lists the hexadecimal values of the LED codes and
lists the category of the code.
Table 81 Console LED Codes
Code
Category of Code
f0 through ff, and 20
SROM Power-up sequence
30 through 3F
ASIC
20 through 2f
Memory
3A through 3E
TOY clock or NVR
40 through 4f
SCC
50 through 5F
NI
60 through 6F
SCSI
70 through 7F
ISDN
81 through 8C
CXT (graphics)
90 through 9A
MIPS Emulator
If no fatal errors occur, the console firmware is loaded and any

further problems display a message on the screen.
84
Error Messages
When the power-up tests are successful and the LEDs display
the DD code, you are running at console mode (>>>). At this
point, the system displays error messages on your screen if:
It encounters problems
You enter the show config command
You enter the show error command
An error message is displayed on the screen in the following

format:
?? fru_code error_code message
For example:
?? 003 0050 (ptr(0) = Not Present keybd(2) = Not Present
Where:
FRU Codes
??
Indicates an error has occurred.
003
Is a FRU code indicating that the keyboard is the

problem.
0050
Is an error code that is followed by a more detailed

message.
An FRU code is a message that indicates which field-replaceable

unit (FRU) is causing the problem. Table 82 describes the most
common FRU codes. If your system displays an error code that
you do not understand, or that is not listed in Table 82, refer to
your Service Guide, call the Digital hotline, or call your Digital
service representative for help.
85
Table 82 FRU Codes

FRU
Code
Meaning
Action
000
Unknown, or diagnostic
test does not support
FRU reporting.
001
System and/or CPU

modules are most
probable FRUs.
You could also be
having audio or system
option problems.
Visually inspect all components to

make sure they are not defective and
are securely connected. If necessary,
replace the system module or
CPU, or call your Digital Services
representative. Check to see if the
audio cable is installed correctly.
003
Keyboard is most
probable FRU.
Be sure the cable is installed

correctly in the connector block,
and that none of the keys are stuck.
004
Mouse or pointing
device is most probable
FRU.
Be sure the cable is installed

correctly in the connector block,
and that none of the buttons are
stuck.
010
TURBOchannel option
in slot 0 is most
probable FRU. (Models
300/300X/300LX only)
Be sure the TURBOchannel cable is

secure and the module is seated
correctly. Visually inspect the
module to be sure it has no defective
components. If necessary, replace
the TURBOchannel module.
011
TURBOchannel option
in slot 1 is most
probable FRU. (Models
300/300X/300LX only)
Be sure the TURBOchannel cable is

secure and the module is seated
correctly. Visually inspect the
module to be sure it has no defective
components. If necessary, replace
the TURBOchannel module.
86
Table 82 (Cont.) FRU Codes

FRU
Code
8xy
Meaning
Action
8xy is a three-digit
hexadecimal number
representing the bank
number and SIMM
with the failing data.
Be sure all SIMMs are installed in

the correct positions and are secure.
Rerun the test to verify.
8 is the extended error

code prefix
x = bank 0 to 7
y = SIMM 0 or 1 for
data errors in one
SIMM
8 is for data errors
in both SIMMS of a
SIMM pair
F if unable to isolate
the error to the SIMM
or SIMM pair.
87

FRU
Code
1 SIMM
2 SIMM
Meaning
Action
Value
SIMM
8,0,0
01
8,1,0
8,0,1
8,1,1
8,2,0
8,3,0
8,2,1
8,3,1
8,4,0
8,5,0
8,4,1
8,5,1
8,6,0
8,7,0
8,6,1
72
8,7,1
0 is the first SIMM next to to the TURBOchannel connector.

7 is the last SIMM at the edge of the module.
88

FRU
Code
1TL
Meaning
Action
SCSI device on SCSI

bus A, Target T, Logical
unit L
For the internal SCSI:
Be sure the power cable and

the internal SCSI cable are
connected securely to the system
module.
Inspect all cables for possible

defects.
Check all jumpers.
If necessary, replace the disk at

address DKA0, for example.
For the external SCSI, be sure there

are no cable defects and the cables
are connected securely.
Error Code
The DEC 3000 Model 300 Series AXP Service Guide lists all
the categories of error codes you may see while in console
mode, according to the FRU that caused the problem. The
FRU is identified by the FRU code in the error message. (See
Table 82).
For example, in the following message, error code 003 (an
SCC communications code) indicates that the problem FRU
is the keyboard. See Table 82 and Table 83 for additional
information.
?? 003 0050 ptr(0) = Not Present keybd(2) = Not Present
Also, look in the SCC LED Codes table in the DEC 3000 Model
300 Series AXP Service Guide to find the error code of 50. This
code indicates that the specific problem is the LK401 keyboard.
89
Table 83 shows the steps to take for a given console diagnostic

test failure.
Table 83 Console-Level Problems
810
Diagnostic Test
Action
CXT
Ensure proper connection of monitor cable.

Ensure proper seating of the CPU module.
Reexecute CXT diagnostic to verify.
ASIC
Ensure proper seating of the CPU module

and reexecute the ASIC diagnostic to
verify.
TOY clock/ NVR

and reexecute the NVR diagnostic to verify.
ISDN

and reexecute the ISDN diagnostic to
verify.
SCC
Add the modem loopback connector.

Reseat keyboard/mouse extension cable.
Reseat the CPU module connection.
Reexecute SCC diagnostic to verify.
SCSI
Ensure proper device connection.

Reseat the SCSI connector to the system
module.
Reexecute SCSI diagnostic to verify.
Be sure all SCSI-2 IDs are unique.
NI
Ensure proper seating of the CPU module.

Add the 10BASE-T loopback connector (if
failure is between error codes A0 to AC).
Reexecute NI diagnostic to verify.
Memory
Reseat memory SIMMs.
TCn
Reseat and/or replace the TURBOchannel

option in the specified slot.
Messages from Other Tests
Messages from Other Tests

Refer to Chapter 4 for details of the set and test commands.
Tests are run in one of three diagnostic modes, each of which is
either set automatically or by using the console set command, as
follows:
The set diag_section 0 command is applied automatically

during power-up diagnostic testing.
After power-up is complete, you are automatically switched
to set diag_section 1.
The set diag_section 1 command initiates the default

customer diagnostic test, entered after power-up tests have
completed and the system is running.
The set diag_section 2 command initiates a service

diagnostic test, which provides more detailed testing. You
may need to connect loopbacks to run some of these tests.
811
Problem Worksheet
Problem Worksheet
DEC 3000 AXP
Handling Problems Worksheet
DEC service representative telephone number:
300 300L
Serial #:
300X 300LX
System Status (indicate which applies):
Model (circle one):
Item:
System plugged into outlet
Power indicator light lit
Diagnostic display lights lit*
Monitor power light lit
Keyboard working
Mouse working
Console prompt appears
Startup error message displayed
Operating system boots
Software is frozen
Yes
No
*Indicate diagnostic display lights here:

7
5 4
3 2 1 0
Diagnostic test screen display:
Actions taken so far:
Additional notes:
MLO-011300
812
A
Hardware Specifications
Appendix Overview
In This
Appendix
This appendix provides the following system specifications for

the DEC 3000 Model 300 Series AXP system:
Weight and Dimensions
Power Specifications
General Specifications
Environmental Limitations
Acoustical Specifications
A1
System Specifications
Weight and
Dimensions
Table A1 provides the system unit dimensions.

Table A1 System Unit Dimensions - Desktop
Power
Specifications
Weight
Height
Width
Depth
8.2 kg (diskless)
9.6 cm
40.0 cm
43.9 cm
(18 lb)
(3.8 in)
(16.0 in)
(17.3 in)
Table A2 provides the power specifications for the DEC 3000

Model 300 Series AXP System system.
Table A2 System Power Specifications
A2
Voltage requirements
120 V/240 V
Voltage tolerance
88 to 132 v/176 to 264 V
Frequency
Single phase: 50 Hz/60Hz
Frequency tolerance
47 to 63 Hz
Watts
260 AC
Maximum running
current
4.0 A/2.0 A
Maximum power
consumption
260 W
General
Specifications
Table A3 provides various information about the system and its

components and options.
Table A3 System Specifications
Processor
DECchip 21064 RISC-style microprocessor,

with 256 KB secondary cache.
SIMM memory
64 MB to 256 MB
Optional fixed disk
Two 3-inch fixed disks
Optional removable-media
drive (RX26)
2.8 MB 3.5-inch, half-height drive
Optional RRD42 compact

disc (CD) drive
External 600-MB 5-inch, half-height CD

drive
Optional expansion boxes
BA353, SZ12, SZ16
Interfaces
One single-channel SCSI-2 compliant

controller (SCSI channel A), that supports
both synchronous and asynchronous
devices, one 10BASE-T Ethernet port (10
Mbits/s), one ISDN port, one synchronous
communications/printer/alternate console
port, one audio port.
Dedicated power source

with an isolated ground
Power source must be 110-120V AC or

220-240V AC.
A3
Environmental
Limitations
Table A4 provides information about the environmental

conditions in which the DEC 3000 Model 300 Series AXP
System can operate. The term "operating conditions" refers to
a system that is plugged in, turned on and running. The term
"nonoperating conditions" refers to a system that is plugged in,
not turned on, and not running.
Table A4 System Environmental Specifications
Operating Conditions
Temperature range
10C to 40C
(50F to 104F)
Temperature change rate
11C/hr (20F/hr) maximum
Relative humidity
10% to 90% (noncondensing)
Altitude
0 to 2000 m (0 to 6562 ft) at 36C (97F)
Maximum wet bulb

temperature
28C (82F)
Minimum dew point
2C (36F)
Nonoperating Conditions
A4
Temperature range
40C to 66C (40F to 151F)
Relative humidity
5% to 95%, (noncondensing)
Maximum altitude
3600 m (12,000 ft)
Maximum wet bulb

temperature
46C (115F)
Acoustical
Specifications
Table A5 lists the English-language acoustical specifications.

Table A5 AcousticsDeclared Values per ISO 9296 and ISO
7779
Product
Sound Power Level

LwAd , B1
Idle
Operate
Sound Pressure Level

LpAm , dBA (operator position)
Idle
Operate
PE30A
4.7
4.7
36
36
PE30A +
2xRZ25
4.8
4.8
37
37
11
B = 10 dBA
A5
B
Internal Options: Specifications and SCSI
ID Settings
Appendix Overview
In this
Appendix
This appendix provides the following option specifications:
RX26 Drive Specifications
RX26 Diskette Specifications
RZ25 Fixed Disk Specifications
B1

Weight and
Dimensions
Operating
Conditions
The following table lists the weight and dimensions of the drive:
Weight
Height
Width
Depth
425 g
(0.94 lb)
2.54 cm
(1.00 in)
10.16 cm
(4.00 in)
15.00 cm
(5.91 in)
The following table lists the operating conditions of the drive:

Variable
Operating Level
Temperature change rate
11C (20F) per hour, maximum
Temperature range
5C to 50C (40F to 122F)1
Relative humidity
8% to 80%, noncondensing
Maximum wet bulb

temperature
25.6C (78F)
Altitude
300 m to 3050 m
(1000 to 10,000 ft) maximum
Power
1.25 watts (read/write)

4.60 watts (seek)
Standby power
0.30 watts
1 Reduce
maximum temperature by 1.8C (5.24F) for each 1000-meter (3300-foot)

increase in altitude.
B2
Nonoperating
Conditions
The following table lists the nonoperating conditions of the drive:

Variable
Level
Temperature range
40C to 66C (40F to 151F)
Relative humidity
Maximum wet bulb

temperature
46C (115F), packaged, noncondensing
Altitude
300 m to 12,200 m (1000 to 40,000 ft)

max.

Diskette
Performance
The following table lists the performance of a diskette:

Variable
Description
Data access time
Minimum time: 3 ms
Average time: 15 ms
Data transfer rate
Double density: 250 Kb/s

High density: 500 Kb/s
Extra density: 1000 Kb/s
Seek time
3 ms minimum; 15 ms average
Average latency
100 ms
Number of cylinders
80
Number of heads
Track density
135 tracks/in
Recording surfaces
per diskette
Sectors per track
9 DD; 18 HD; 36 ED
B3
Storage
Capacity
SCSI ID Switch
Settings
The following table lists the storage capacity of an RX26

unformatted diskette, depending on the density of the diskette:
Read/Write
Capability
Diskette
Capacity
Double density (DD)

8.89 cm (3 inches)
737,280 bytes per drive

4608 bytes per track
Read
High density (HD)

8.89 cm (3 inches)
1,474,560 bytes per drive

9216 bytes per track
Read/write
Extra density (ED)

8.89 cm (3 inches)
2,949,120 bytes per drive
Read/write
For proper communication between your system and an RX26

drive, your RX26 must have a unique SCSI address setting.
SCSI address settings are determined by the position of
electrical switches located on the sides of the drive.
The SCSI-ID Address Setting
When your RX26 drive arrives from the factory, it should be
preset to the recommended SCSI setting of 5, as shown in
Figure B1. Figure B1 also shows all possible SCSI ID settings
for the RX26 drive.
Note
SCSI ID 7 is reserved for the host SCSI controller.
B4
Figure B1 RX26 Switch Settings
O
F
F
12
2
O
4
12
5
12
12
12
12
12
12
12
3
MLO-010748
switch settings
switch settings
When setting SCSI ID addresses for the RX26, remember that no
two devices can be set to the same SCSI ID. Refer to the section
entitled Understanding SCSI IDs in Chapter 2 for additional
information.
B5

Weight and
Dimensions
Formatted
Storage
Capacity
Performance
B6
Weight
Height
Width
Depth
0.8 kg
4.1 cm
10.2 cm
14.6 cm
(1.8 lb)
(1.63 in)
(4.0 in)
(5.75 in)
The following table lists the formatted storage capacity of the

drive:
Variable
Description
Megabytes per drive
426
Megabytes per surface
47.3
Bytes per track
24,576-37,376 (variable)
Bytes per block
512 bytes
Blocks per drive
832,031
Blocks per track
48
Spare blocks per track
Spare blocks per drive
14,148
Spare cylinders
Buffer size
60 KB
The following table lists the performance of the drive:

Variable
Description
Transfer rate to/from media
2.1-3.2 MB/sec (variable)
Transfer rate to/from buffer
2.33 MB/sec
Bus asynchronous mode
3.0 MB/sec
Bus synchronous
4.0 MB/sec
Operating
Conditions
Variable
Description
Seek time track to track
2 ms
Seek time average
14 ms
Seek time maximum (full

stroke)
28 ms
Average rotational latency
6.8 ms
Rotational speed
4412 0.5%
Start time
20 s maximum
Stop time
30 s maximum
Interleave ratio
1:1

Operating Variable
Operating Level
1
Ambient Temperature
10C to 55C
(50F to 122F)
Relative Humidity
Maximum wet bulb

temperature
25.6C
(78F)
Minimum dew point

temperature
2C (36F)
Altitude
30.48 m to 304.78 m
(100.58 ft to 1005.77 ft) at 36C (96F)
1 Reduce
maximum temperature by 1.8C (3.24 F) for each 1000-meter (3300-foot)

B7
Nonoperating
Conditions
SCSI ID Jumper
Settings
B8

Nonoperating Variable
Level
Ambient Temperature
40C to 66C
(40F to 151F)
Relative Humidity
Maximum wet bulb

temperature
46C (115F)
Minimum dew point

temperature
2C (36F)
Altitude
-300 m to 3,000 m (-984.3 ft to 9843 ft)

at 36C (96F)
Figure B2 shows the SCSI ID settings for the RZ25 fixed disk
drive. There are three jumper locations, J5, J6, and J7. Use J5
only. Remember, no two devices can be set to the same SCSI ID.
Refer to Chapter 2 for additional information.
Figure B2 RZ25 Jumper Settings
4
3
MLO-010749
J5 jumpers
J7 jumpers
J6 jumpers
jumper settings, SCSI ID 03
jumper settings, SCSI ID 47
B9
Table B1 lists the RZ25 jumper settings for both customer

and Digital Services use; Table B2 and Table B3 jumper
settings are provided for Digital Services and self-maintenance
customers. In Table B1, Out = removed; In =attached.
Table B1 J5 Jumper Settings
SCSI Address
Out
Out
Out
In
Out
Out
Out
In
Out
In
In
Out
Out
Out
In
In
Out
In
Out
In
In
In
In
In
1 Reserved
for host SCSI ID.

Jumper Position
Description
J6-1
Factory use only
J6-2
In = Enables motor start option

Out = Drive operation depends on whether a
jumper is installed in J6-3
J6-3
In = Enables motor start option (if J6-2 is out).

Motor start delay is 16 times the drive ID
number in seconds.
J6-4
In = Entire drive is write-protected.
J6-5
In = Parity checking by drive is enabled.
J6-6
Reserved for later use.
J6-7
In = Supplies drive power to SCSI bus, pin 26.

B10
Table B2 (Cont.) J6 Jumper Settings

Jumper Position
Description
J6-8
In = Supplies power only to drive terminators.
Note
If J6 pins 7 and 8 are positioned horizontally (lower
part), the drive takes power from the SCSI bus, pin 26.
Jumpers on both pins 7 and 8 can be in at the same time.
Remove all jumpers from location J7 except jumper 4. Failure to

do so could cause dual SCSI address problems.
Jumper Position
Description
J7-1
SCSI ID (use J5 ID setting)
J7-2
J7-3
J7-4
Jumper must be installed if no cable is

connected.
J7-5
Used for a connection to a remotely located

LED indicator.
B11

Weight and
Dimensions
Formatted
Storage
Capacity
Weight
Height
Width
Depth
0.7 kg
2.5 cm
10.2 cm
14.6 cm
(1.5 lb)
(1.00 in)
(4.0 in)
(5.75 in)
The following table lists the formatted storage capacity of the

drive:
Table B4 RZ25L Hardware Specifications
Formatted Storage Capacity
Performance
Per drive
535 MB
Per surface
90.7 MB
Bytes per track
48,460 (average)
Bytes per block
512
Spare blocks per track
Spare cylinders
Buffer size
240 KB

Performance
B12
Data transfer rate to/from media
5.25 MB/sec (maximum)
1.5 msec
Seek time average
10.5 msec
Operating
Conditions
Seek time maximum (full stroke)
23 msec
Average latency
5.4 msec
Rotational speed
5411 rpm
Interleave ratio
1:1
6 0.5%

Operating Conditions
Nonoperating
Conditions
Ambient temperature
5C to 50C (41F to 122F)
Relative humidity
8%80%
Altitude
305 m to 3048 m (1000 ft to

10,000 ft)
Maximum wet bulb temperature
28C (82F) (noncondensing)
Heat dissipation
8.4W (seeking) 7W
(typical)
Temperature gradient
20C/hr (36F/hr)

Nonoperating Conditions
SCSI ID Jumper
Settings
Ambient temperature
40C to 70C (40F to 158F)
Relative humidity
5%95%
Altitude
305 m to 12,210 m(1000 ft to

40,000 ft)
Maximum wet bulb temperature
46C (115F)
25C (45F/hr)
Figure B3 shows the SCSI ID settings for the RZ25L fixed disk
drive. You may need to remove the bracket attached to an RZ25L
drive to access the jumper locations. Remember, no two devices
can be set to the same SCSI ID. SCSI ID 7 is reserved for the
host SCSI ID. Refer to Chapter 2 for additional information.
B13
Figure B3 RZ25L Jumper Settings
MLO-011298
SCSI jumper settings 03

B14

Weight and
Dimensions
Formatted
Storage
Capacity
Performance
Weight
Height
Width
Depth
0.9 kg
4.12 cm
10.2 cm
14.6 cm
(1.9 lb)
(1.625 in)
(4.00 in)
(5.75 in)
The following table lists the storage capacity of the drive:

Variable
Description
Bytes per track
29,640
Megabytes per drive
1050
Megabytes per surface
75
Buffer size
512 KB

Variable
Description
Transfer rate to/from media
2.6 MB/s
1 ms
Seek time average
10 ms
20 ms
Average rotational latency
5.6 ms
Rotational speed
5363 rpm
B15
Operating
Conditions

Operating Variable
Ambient temperature
Operating Level
1
Relative humidity
10C to 50C
(50F to 122F)
10% to 90%
1 Reduce

Nonoperating
Conditions
SCSI ID Jumper
Settings
B16

Level
Ambient temperature
40C to 66C
(40F to 151F)
Relative humidity
drive. SCSI ID 7 is reserved for the host SCSI ID.
MLO-010750
SCSI ID jumper settings 03

SCSI ID jumper settings 47
When setting SCSI ID addresses for the RZ26, remember no
two devices can be set to the same SCSI ID, see Chapter 2 for
additional information.
B17

Weight and
Dimensions
Formatted
Storage
Capacity
Performance
Weight
Height
Width
Depth
0.49 kg
2.54 cm
10.2 cm
14.6 cm
(1.08 lb)
(1.00 in)
(4.00 in)
(5.75 in)

Variable
Description
Bytes per drive
1.05 GB (formatted)
Buffer size
512 KB

Variable
B18
Description
2.75.5 MB/sec
1 msec
Seek time average
9.5 msec
20 msec
Average latency
5.6 msec
Rotational speed
5400 rpm
Interleave ratio
1:1
Operating
Conditions

Operating Variable
Ambient temperature
Operating Level
1
5C to 55C
(41F to 131F)
Relative humidity
10%90% non-condensing
Maximum wet bulb
32C 90F
20C 36F per hour
1 Reduce

Nonoperating
Conditions
SCSI ID Jumper
Settings

Level
Ambient temperature
40C to 66C
(40F to 151F)
Relative humidity
8%95% (noncondensing)
Maximum wet bulb
46C 115F
30C 55F per hour
Figure B5 shows the SCSI ID settings for the RZ26L fixed disk
Note
No special termination is required on workstations.
B19
Figure B5 RZ26L Jumper Settings
MLO-011299

When setting SCSI ID addresses for the RZ26L, remember no
B20

Weight and
Dimensions
Formatted
Storage
Capacity
Performance
Weight
Height
Width
Depth
0.9 kg
4.13 cm
10.2 cm
14.6 cm
(1.9 lb)
(1.63 in)
(4.00 in)
(5.75 in)

Variable
Description
Megabytes per drive
2104
Gigabytes per drive
2.1
Bytes per track
30,208
Bytes per surface
144,683,520
Buffer size
1024 KB

Variable
Description
2.7MB/sec
Interface transfer rate,

synchronous
10 MB/sec
Interface transfer rate, async
5 MB/sec
1 msec
Seek time average
10 msec
20 msec
Average latency
5.6 msec
Rotational speed
5400 rpm
6 0.5%
B21
Operating
Conditions
Nonoperating
Conditions
SCSI ID Jumper
Settings
B22

Operating Variable
Operating Level
Ambient temperature
5C to 55C (41F to 131F)
Relative humidity
10%90%

Level
Ambient temperature
40C to 66C (104F to 151F)
Relative humidity
8%95% (packaged)
MLO-010750

When setting SCSI ID addresses for the RZ28, remember no
B23
C
Port Pinouts
Appendix Overview
Introduction
This appendix is for users who want to connect communications

devices to their system. The tables in this appendix explain the
functions of the pins on the communication ports.
In This
Appendix
The following communications ports are listed in this appendix.
External SCSI Port
10BASE-T Port
ISDN Port
Audio Port
Keyboard/Mouse or Tablet Port
RS-232 Synchronous/Asynchronous Communications Port
Figure C1 Communications Ports
ISDN
MLO-010140
C1
External SCSI Port
External SCSI Port

Pin Layout
Pin-Outs
The following figure shows the pin layout for the external SCSI
port.
25
50
26
Table C1 describes pin usage for the external SCSI port.

Table C1 External SCSI Port Pin-outs
Pin
Description
Pin
Description
Chassis ground
26
SCSI Bus Data [0]
Chassis ground
27
SCSI Bus Data [1]
Chassis ground
28
SCSI Bus Data [2]
Chassis ground
29
SCSI Bus Data [3]
Chassis ground
30
SCSI Bus Data [4]
Chassis ground
31
SCSI Bus Data [5]
Chassis ground
32
SCSI Bus Data [6]
Chassis ground
33
SCSI Bus Data [7]
Chassis ground
34
SCSI Bus Data Parity
10
Chassis ground
35
Chassis ground
11
Chassis ground
36
Chassis ground
12
Chassis ground
37
Chassis ground
13
Not used
38
Term power
14
Reserved
39
Reserved
15
Chassis ground
40
Chassis ground
C2
External SCSI Port
Table C1 (Cont.) External SCSI Port Pin-outs

Pin
Description
Pin
Description
16
Chassis ground
41
SCSI Bus ATN
17
Chassis ground
42
Chassis ground
18
Chassis ground
43
SCSI Bus BSY
19
Chassis ground
44
SCSI Bus ACK
20
Chassis ground
45
SCSI Bus RST
21
Chassis ground
46
SCSI Bus MSG
22
Chassis ground
47
SCSI Bus SEL
23
Chassis ground
48
SCSI Bus CD
24
Chassis ground
49
SCSI Bus REQ
25
Chassis ground
50
SCSI Bus IO
C3
10BASE-T Port
10BASE-T Port
Pin Layout
The following figure shows the pin layout for the 10BASE-T port.
1
MLO-008912
Pin-Outs
Table C2 describes pin usage for the 10BASE-T port.

Table C2 10BASE-T Port Pin-outs
C4
Pin Number
Description
Transmit
Transmit, active low
Receive
Not used
Not used
Receive, active low
Not used
Not used
ISDN Port
ISDN Port
Pin Layout
The following figure shows the pin layout for the ISDN port.
8
MLO-008611
Pin-Outs
Table C3 describes pin usage for the ISDN port.

Table C3 ISDN Port Pin-outs
Pin Number
Description
Not used
Not used
Line out, active low
Line in
Line in, active low
Line out
Not used
Not used
C5
Audio Port
Audio Port
Pin Layout
The following figure shows the pin layout for the audio port.
Pin-Outs
Table C4 describes pin usage for the audio port.

Table C4 Audio Port Pin-outs
Pin Number
Description
Audio in A
Earphone interface 1 (audio out)
Earphone interface 2 (audio out return)
Audio input B (ground)
This port is pin-compatible with a telephone handset.
C6

Pin Layout
The following figure shows the pin layout for the keyboard/mouse
or tablet port.
1
Pin-Outs
15
Table C5 describes pin usage for the keyboard/mouse or tablet

port. The tablet, keyboard, and mouse interface use the same
physical port.
Table C5 Keyboard/Mouse or Tablet Port Pin-outs
Pin
Signal
Description
GND
Chassis ground
KEY.TX
Keyboard transmitted data
KEY.RX
Keyboard received data
+12V
Keyboard/tablet power
GND
Chassis ground
MSE.RX
Mouse received data
MSE.TX
Mouse transmitted data
GND
Chassis ground
GND
Chassis ground
10
NC
Not used
11
NC
Not used
12
NC
Not used
13
+5V
Mouse power
14
-12V
Mouse power
15
GND
Chassis ground
Source
Keyboard
Mouse/tablet
C7

Pin Layout
The following figure shows the pin layout for the RS-232
synchronous/asynchronous communications port.
1
14
Port Pin-Outs
13
25
Table C6 describes pin usage for the synchronous/asynchronous

communications port.
Table C6 Synch/Asynch Communications Port Pin-outs
C8
Pin
Description
Pin
Description
Protective ground
14
Not used
Transmit data
15
Transmitter signal element

timing
Receive data
16
Not used
Request to send
17
Receiver signal element timing
Clear to send
18
Not used
Data set ready
19
Not used
Signal ground
20
Data terminal ready
Data channel received
21
Not used
Not used
22
Ring indicator
10
Not used
23
Data signal rate selector
11
Not used
24
Not used
12
Speed mode indicator
25
Not used
13
Not used
D
Associated Documents
Introduction
For option and system hardware part numbers, consult your

Digital sales representative.
Not all the following documents are available in every country.
Check with your Digital sales representative for availability.
Associated
Printed
Documents
Table D1 lists the associated documents and material available

in printed form.
Table D1 DEC 3000 Model 300 Series AXP System Printed
Documents
Titles
Order Numbers
DEC 3000 Model 300 Series AXP Systems
DEC 3000 Model 300 Series AXP

Hardware Reference Guide
EKPELCNOG
DEC 3000 Model 300 Series AXP Service

Guide
EKPELCNSV
DEC 3000 Model 300 Series AXP Setting

Up Your System
EKPELHWIC
DEC 3000 Model 300 Series AXP Adding

Memory
EKPELAMIC

an Internal Fixed Disk Drive
EKPELADIC
D1
Table D1 (Cont.) DEC 3000 Model 300 Series AXP System

Printed Documents
Titles
Order Numbers
DEC 3000 Model 300 Series AXP Systems

a Removable-Media Drive
EKPELAFIC
OpenVMS AXP Factory Installed

Software (FIS) User Information
EKA0377UG
DEC OSF/1 AXP Factory-Installed

Software User Information
EKSFFISUG
TURBOchannel-related Documentation
Smart Frame Buffer TURBOchannel

Module
EKSFBOMTC
Smart Frame Buffer Plus Module Owners

Guide
EKSMFBPSG
ZLX Graphics Accelerator Modules

Owners Guide
EKPIXELOG
The ThickWire Ethernet TURBOchannel

Module
EK-TWETH-TC
TURBOchannel Extender Operators

Guide
EK-PM32X-EX
TURBOchannel Extender (TCE) Option

Module
EK-TCEIM-TC
SCSI TURBOchannel Option Installation

Kit
EKPMAZAUG
DEC FDDIcontroller 700 Installation
EKDEFZAIN
FDDIcontroller 700 Release Notes
AAPJKWATE
Dual SCSI Module Owners Guide
EKDSCSEOG
Dual SCSI Module (PMAZCAA) Owners

Guide
EKSCSIBOG
D2

Printed Documents
Titles
Order Numbers
Multimedia Documentation
Sound and Motion J300 Owners Guide
EKJXPVSUG
Multimedia Services for DEC OSF/1 AXP

Installation Guide
AAQ0ANATE
Multimedia Services for DEC OSF/1 AXP

Programmers Guide
AAQ0APATE
DEC 3000 Firmware Documentation
Alpha AXP Systems Firmware Release

Notes
AAPW8YETE
Drives
600 MB SCSI CD-ROM Installation

Guide
EKXCRAAIG
OpenVMS AXP Version 1.5 Compact Disc

Users Guide
AVPQYVARE
RX26 Owners Reference Card
EKRX26DRC
RZ Series Disk Drive Reference Manual
EKRZXXDRM
RZ Series Disk Drive Installation Guide
EKDRZ01IG
RRD42 Compact Disc Drive Owners

Manual
EKRRD42OM
TZK10 Cartridge Tape Drive Owners

Guide
EKTZK10OG
TLZ06 Cassette Tape Drive Owners

Guide
EKTLZ06OM
TZ30 Cartridge Tape Drive Owners

Guide
EKTZ30COG
D3

Printed Documents
Titles
Order Numbers
SCSI Documents
Small Computer System Interface: An

Overview
EKSCSISOV
Small Computer System Interface: A

Developers Guide
EKSCSISSP
OPEN DECconnect Documentation
OPEN DECconnect Building Wiring

Components and Applications Catalog
DEC OSF/1 AXP

Documentation
ECI183429
Table D2 lists the user DEC OSF/1 AXP documentation kit and
its contents:
Table D2 End User Documentation, QAMT4ABGZ
D4
Titles
Order Numbers
Startup Documentation Subkit
QAMT4ACGZ
Release Notes
AAPS2BATE
Guide to Installing DEC OSF/1
AAPS2DATE
Guide to Software License Management
AAPS2EATE
Read This First Letter
AVPS3JATE
Quick Reference (card)
AVPS3KATE
OpenVMS AXP
Documents
Table D3 lists some of the OpenVMS AXP documentation:

Table D3 General OpenVMS AXP Operating System
Documents
Miscellaneous
Documents
Titles
Order Numbers
OpenVMS Alpha Version 1.5 Upgrade and

Installation Manual
AA-PV6XA-TE
OpenVMS System Managers Manual:

Essentials
AA-PV5MA-TK
OpenVMS System Managers Manual:

Tuning, Monitoring, and Complex Systems
AA-PV5NA-TK
OpenVMS Alpha Layered Products Compact

Disc Users Guide
AAPSQVCRE
OpenVMS AXP Version 1.5 Release Notes
AA-PV72A-TE
Overview of OpenVMS Documentation
AA-PV6YA-TK
Table D4 lists other documentation that may be useful to you:

Table D4 Miscellaneous Documents
Titles
Linkworks Users Guide

GNU Emacs Manual
GNU Emacs Lisp Reference Manual
Guide to Prestoserve
D5
E
Help in Debugging Programs
Appendix Overview
Memory-Based
Data Structures
The DEC 3000 AXP console stores away memory-based data

structures that may help in debugging certain crashes. These
structures are:
Impure areaThis area contains the saved machine state on

an entry into console.
Machine check logoutThis area contains the last machine

check log caused by:
A system/processor correctable error (small frame)
A system/processor uncorrectable error (large frame)
For example:
A MCHECK FR PAL (Machine CHECK FRom PAL) implies
that the system encountered a machine check condition while
executing PALcode and not while executing operating system
code. Because of this, an operating system level crash dump
does not take place. Instead, a machine check logout frame
is created by the PALcode before entering console mode. This
logout frame may be examined while in console mode, using
the examine commands.
In This
Appendix
This appendix describes each data structure.
E1
Examining the Impure Area

Commands
and Display
Elements
Enter the following command to examine the impure area:

>>> E -PM -Q -U -N 94 F4000
You must use the ctrl-s (XOFF) and ctrl-q (XON) commands to
stop and start the display. The following are the address and
description of each element in the impure area.
Console Flags - Address: F4000h
Console Halt Reason - Address: F4008h
Saved General-Purpose Registers - Address: F4010h F4108h

Description: Contents of the general-purpose register R0
-R31 at time of console entry.
Saved Floating-Point Registers - Address: F4110h - F4208h

Description: Contents of the floating-point register FR0 FR31 at time of console entry
Machine Check Flag - Address: F4210h
Saved PAL Temp Registers - Address: F4218h - F4310h

Description: Contents of PT0 - PT31 on console entry.
Operating system use.
E2
Exception Address - Address: F4318h
PAL Base - Address: F4320h
Saved HIRR - Address: F4328h
Saved HIER - Address: F4330h
Saved MMCSR - Address: F4338h
Saved VA - Address: F4340h
Saved BIU_ADDR - Address: F4348h
Saved BIU_STAT - Address: F4350h
Saved DC_ADDR - Address: F4358h
Saved FILL_ADDR - Address: F4360h
Saved DC_STAT - Address: F4368h
Saved FILL_SYNDROME - Address: F4370h
Saved BC_TAG - Address: F4378h
Saved ABOX_CTL - Address: F4380h
Saved BIU_CTL - Address: F4388h
Saved FP_CSR - Address: F4390h
Console Entered State Variable - Address: F4398h
Saved Values of the PAL Temp Registers - Address: F43A0h

- F4498h
Description: Contents of PAL temps when in console
mode.
Saved PAL Base Register - Address: F44A0h
Examining the Machine Check Logout Area

To Examine the
Small Frame
Enter the following command to examine the machine check

logout area: To look at the small frame:
>>> E -PM -Q -U -N A F8000
stop and start the display.
The following are the address and description of each element in
the small frame in the logout area:
Flag Field - Address: F8000h

Description: Contains the size of the frame in the low
longword and the retry bit is represented by bit 63
Offset Field - Address: F8008h

Description: Byte offset to the CPU specific part of the
logout frame in low longword, offset to the system error
code is in the high longword.
E3
To Examine the
Large Frame
Machine Check Error Code - Address: F8010h
BIU_STAT Contents- Address: F8018h
BIU_ADDR Contents - Address: F8020h
DC_STAT Contents - Address: F8028h
FILL_SYNDROME Contents - Address: F8030h
FILL_ADDR Contents - Address: F8038h
BC_TAG Contents - Address: F8040h
Machine Check Error CODE - Address: F8048h
Enter the following to look at the large frame:

>>> E -PM -Q -U -N 3B F8050
stop and start the display.
The following are the address and description of each element in
the large frame in the logout area:
Flag Data - Address: F8050h

Description: Low longword contains the size of the log in
the low longword, bit 63 is used as a retry bit
Offset Data - Address: F8058h

Description: Low longword is offset to CPU specific data,
high longword is offset to system specific data.
Machine Check Code - Address: F8060h
Saved PAL Temp Registers - Address: F8068h - F8158h

Description: Contents of PT0 - PT31 at the time of the
error
Saved Exception Address- Address: F8160h

Description: Address that was executing at the time of
the machine check
E4
Saved Exception Summary Register - Address: F8168h
Saved Exception Mask Register - Address: F8170h
Saved ICSSR - Address: F8178h
Saved PALbase - Address: F8180h
Saved HIER - Address: F8188h
Saved HIRR - Address: F8190h
Saved MMCSR - Address: F8198h
Saved DC_STAT - Address: F81A0h
Saved DC_ADDR - Address: F81A8h
Saved ABOX_CTL - Address: F81B0h
Saved BIU_STAT - Address: F81B8h
Saved BIU_ADDR - Address: F81C0h
Saved BIU_CTL - Address: F81C8h
Saved FILL_SYNDROME - Address: F81D0h
Saved FILL_ADDR - Address: F81D8h
Saved VA - Address: F81E0h
Saved BC_TAG - Address: F81E8h
Machine Check Code - Address: F81F0h
Memory Configuration Status - Address: F81F8h
Saved TCASIC SLOT MODE Register - Address: F8200h
Saved TCASIC CONFIG Register - Address: F8208h
Saved TCASIC Failing Address Register - Address: F8210h
Saved TCASIC Error Register - Address: F8218h
Saved TCASIC Interrupt Register - Address: F8220h
Saved Interrupt Mask Register - Address: F8228h
E5
F
Supplementary Information for PTT
Network Users
Appendix Overview
Introduction
Certain European countries and the United Kingdom require

that installation information be provided on the system
module (5422249), which is hosted within the DEC 3000 Model
300 Series AXP systems.
In This
Appendix
This appendix includes the following information:
Service Specifications
Host Power Rating
Module Isolation
Safety Warnings for UK Installations Only
Cable Approval for the UK Only
Supported Cables
Equipment Between the Approved Module and a Digital

Circuit (PTT)
F1
Appendix Overview
Service
Specifications
Table F1 lists the service specifications for the system module.
Table F1 Service Specifications for the System Module
Service
Category
Interface
Type
(CCITT
recommendation)
Service Requirements
Electrical
X.21bis
V.24
/V.28
Physical
ISO 2110,
BS.6623:
part1, 1985.
Approved extension
cables: 2
BC22F-25 (25 feet) and
BC22F-10 (10 feet)
1 BT
British Telecommunications plc.

Hull Kingston Communications (Hull) plc.
MCL Mercury Communications Limited.
2 The
F2
Data Rate
Public
Telecommunications
Operators1
total length of cable used must not exceed 27 feet.
2400 bps
4800 bps
9600 bps
19200 bps
BT
Hull
MCL
Yes
Yes
Yes
No
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Appendix Overview
Host Power
Rating
You must ensure that the total power drawn by the approved
module, the host, and other auxiliary equipment drawing power
from the host, is within the rating of the host power supply.
Digital has designed all permutations of the host configuration
(including the DEC 3000 Model 300 Series AXP Systems) to
operate within the limits of the host power rating, as shown in
Table F2.
Table F2 Module Power
Maximum
Input
Current
(Amperage)1
Maximum
Input
Current
(Amperage)2
+5.304
16.0
24.0
+11.616
+12.584
0.8
1.8
11.4
12.6
0.1
0.1
Nominal
Voltage
Maximum
Voltage
(Volts)
Maximum
Voltage
(Volts)
+5.1V
+4.896
+12.1V
12.0V
1 Without
TURBOchannel options slots populated.
2 With
two TURBOchannel options slots populated. This is a worst-case situation

as specified in the TURBOchannel hardware specification.
Module
Isolation
Digital has ensured that when the system module is installed

within the DEC 3000 Model 300 Series AXP Systems, the
clearance and creepage distances to the host are met. Clearance
is the shortest distance in air between two points. Creepage is
the shortest distance along a continuous surface between those
same two points.
Creepage distances apply when the system module is installed in
a controlled environment. You can check creepage distances by
measuring the distance between adjacent parts.
If in doubt, you should seek the advice of a telecoms safety
engineer. Failure to install the system module in accordance
with these instructions will invalidate the approval.
F3
Appendix Overview
Except at the connector that plugs into the host, clearance and
creepage distances of Xmm and Ymm, as listed in Table F3,
must be maintained between the approved module and other
parts of the host, including expansion cards.
Table F3 Clearance and Creepage Distances
Clearance
Xmm
Creepage
Ymm
Voltage Used or Generated by Other

Parts of the Host or Expansion Card
Vrms or Vdc
2.0
2.4 (3.8)1
Up to 50
2.6
3.0 (4.8)
Up to 125
4.0
5.0 (8.0)
Up to 250
4.0
6.4 (10.0)
Up to 300
1 The
distances shown in parentheses apply in an uncontrolled environment

where heat, humidity, and temperature may fluctuate.
Safety
Warnings for
UK Installations
Only
Ports indicated by the safety warning label do not provide

sufficient isolation to satisfy the requirements of the relevant
parts of standard BS6301. Therefore, any product connected to
this port must meet one of the following conditions:
Be covered by the Office of Telecommunications (OFTEL)s

General Approval NS/G/1234/J/100003
(All products supplied by Digital comply with this General
Approval.)
Have been approved to the relevant parts of standard

BS6301
Have previously been evaluated against British Telecom

(Post Office) Technical Guide 2 or 26 and given permission to
attach
Any other use of this product invalidates approval.
F4
Appendix Overview
If a port has the following label, direct or indirect interconnection

of that port, whether the port is marked or not, may produce
hazardous conditions on the network:
SAFETY WARNING --- See Instructions for Use Before Making Any
Connection to This Module
The warning label applies to all ports labeled

Figure F1.
through
in
Figure F1 Ports to Which Warning Label Applies
10
11
12
MLO-009782
The numbers correspond to the following ports:

Monitor port
Keyboard/mouse port
Audio input/output port
ISDN port
10BASE-T port
External SCSI port
TURBOchannel 1
TURBOchannel 0
CPU module
Power supply connector
F5
Appendix Overview
Fixed disk/removable disk/SCSI interface

Memory
Note
ISDN communications are not yet available for your
workstation. ISDN ports for connection to PTT public
service networks will be provided by a product update to
be released in the near future.
Cable Approval
for the UK Only
F6
The system module is approved for direct connection to

a particular digital circuit. This approval includes an
interconnecting cable with mating connectors that conform
to the British standard BS6623, parts 1 and 4. If the module
is connected to the service with anything other than its own
approved cables, those cables must benefit from relevant
general approval NS/G/1235/100009 and/or conform to any other
applicable requirements.
Appendix Overview
The following table describes pin usage for the system module
connector.
Supported
Cables
Pin
Description
Pin
Description
Ground
14
Not used
Transmit data
15
Transmit data
Receive data
16
Not used
Request to send
17
Receive clock
Clear to send
18
Not used
Data set ready
19
Not used
Ground
20
DTR
Carrier detect
21
Not used
Not used
22
Ring indicator
10
Not used
23
Data signal rate selector
11
Not used
24
Not used
12
Speed indicator
25
Not used
Table F4 describes the cables for the system module.

Table F4 Cables Supported by the Approved Module
Interface
Cable Type
Order Number
Molding Pins
V.24
Extension
BC22F-10 (10 feet)
straight
25-25
V.24
Extension
BC22F-25 (25 feet)
straight
25-25
F7
Appendix Overview
Equipment
Between the
Approved
Module and a
Digital Circuit
(PTT)
If any other equipment, including cables or wiring, is to be

connected between the approved module and the point of
connection to any particular digital circuit, that equipment must
conform as follows:
The overall transmission characteristics of all other

equipment must not have any material effect on the
electrical conditions between the equipment and the digital
circuit.
All other equipment must comprise only the following:

Approved equipment, which may be subject to limitations
on its use, for the purpose of connection between it and a
particular digital circuit.
Cable or wiring that complies with a code of practice for
the installation of equipment covered by this standard or
other requirements that may be applicable.
F8
Glossary
10BASE2 Ethernet network
See ThinWire Ethernet network.
10BASE-T Ethernet network
The IEEE standard 802.3-compliant Ethernet products used
for local distribution of data. These networking products
characteristically use a cable made by twisting together two
insulated conductors with no common covering. (Commonly
known as twisted-pair cable.) Compare with thickwire Ethernet
network.
accelerator
A hardware graphics processor that produces faster images than
a CPU and frees the CPU to do other work.
alternate console feature
A feature that allows you to receive system messages on an
alternate console terminal and direct system activities from this
terminal, if necessary, to diagnose problems with the monitor.
ANSI
Abbreviation for American National Standards Institute, an
organization that develops and publishes standards for the
computer industry.
antistatic wrist strap
A grounded strap you connect to your wrist and the system unit
while handling internal devices that are sensitive to static. This
strap prevents electrostatic discharge that could result in loss of
data, or damage to your equipment.
Glossary1
applications
Programs, such as a financial spreadsheet program, that perform
end-user tasks.
architecture
The internal configuration of a computer including its registers,
instruction set, and input/output structure.
ASIC (Application-Specific Integrated Circuit)
Customized chips chosen from a library of circuits. The test
asic command tests the ASIC subsystem.

asynchronous transmission
A type of communications in which data is transmitted at
different time intervals. Compare with synchronous.
AUI (Attachment Unit Interface)
An IEEE standard 802.3-compliant Ethernet network made of
standard Ethernet cable, as opposed to ThinWire Ethernet cable.
Also called standard Ethernet. Compare with ThinWire Ethernet
network. See also standard Ethernet network.
autoboot
The process by which the system boots automatically.
backup copy
A copy of files or software made for safekeeping. Making a
backup copy of the data stored on your disk allows you to recover
that data after an accidental loss. You can make backup copies
on tape cartridges, or over a network using the Remote System
Manager.
baud rate
The speed at which signals are serially transmitted over a
communications line. Baud rates can be measured in bits per
second or characters per second. One baud equals one bit per
second; eight bauds equals one character per second.
bezel
The removable molded panel on the front of the system unit.
Glossary2
bit
A binary digit; the smallest unit of information in a binary
system of notation, designated as a 0 or a 1.
boot
Short for bootstrap, meaning to bring a device or system to a
defined state where it can operate on its own.
boot (or bootstrap) device
The memory storage device that holds the software that carries
out a system bootstrap procedure.
boot console device
The device name from which the console boots the operating
system. This name is listed in a show device display under the
BOOTDEV column. Example: ESA0 indicates the network.
boot flag
An indicator bit, set by the system manager, that contains
information that is read and used by the bootstrap software
during a system bootstrap procedure. Default boot flags should
already be set when you receive your system.
buffer
An internal memory area used for temporary storage of data
records during input or output operations.
bus
A group of signals consisting of transmission lines or
wires to create a common channel or pathway. The bus
interconnects either internal computer system components
to provide communications paths for addresses, data, and
control information or external terminals and systems in a
communications network.
byte
A group of eight contiguous binary digits (bits). Bits are
numbered from right to left, 0 through 7, with bit 0 being the
low-order bit. See also kilobyte and megabyte.
Glossary3
cable
A sheathed group of electrical conductors.
cable junction block
A small block attached to the monitor cable from which the BNC
connectors emerge.
cache
See cache memory.
cache memory
A small, high-speed area of memory placed between slower main
memory and the processor. Cache memory increases memory
transfer rates and processor speed. It contains copies of data
recently used by the processor and fetches several bytes of data
from memory in anticipation that the processor will access the
next sequential series of bytes.
CD
See compact disc.
CD-ROM
See compact disc read-only memory.
central processing unit (CPU)
The unit of the computer that is responsible for interpreting and
executing instructions.
CISC
Complex instruction set computer. A computer that uses
an instruction set consisting of a large number of complex
instructions that are managed by microcode. Contrast with
RISC.
client
A piece of hardware or software that obtains a specific set of
services from a server.
Glossary4
client-server computing
An approach to computing that enables personal computer and
workstation usersthe clientsto work cooperatively with
software programs stored on a mainframe or minicomputerthe
server.
clock
A signal used to synchronize the circuits in a computer system.
cluster
A group of networked computers that communicate over a
common interface to share disk storage, application programs,
and other computer resources.
command
A request made to the operating system to perform a specific
function, for example, a request to run a program or show the
configuration of a system.
communications
The transmission of digital data from one point (the source) to
another (the receiver).
compact disc
A removable flat circular plate, used in the compact disc drive
on which read-only optical data is stored. A laser optical reader
retrieves this information.
compact disc read-only memory
An area of memory that can be read, but not written to.
component
A basic part, or element, of your system that can be either
internal or external. Compare with device.
configuration
See system configuration.
connector
Hardware that connects directly to a port on the system.
Glossary5
console
A device through which an operator communicates with the
computer.
console commands
Commands input when the system is in console mode.
console mode
The state in which the computer is controlled directly by user
commands from the console terminal rather than indirectly
through the operating system. Console mode is in effect when
the system is turned on and the operating system software has
not been started, or the operating system software has been
interrupted by pressing the halt button on the system unit.
Console mode is indicated by the console prompt ( >>> ) on the
monitor screen. Compare with program mode.
console password
The password used to access privileged console commands.
console program
The code that the CPU executes during console mode.
console prompt
The prompt ( >>> ) that appears on the screen when the system
is in console mode.
console subsystem
The subsystem that provides the user interface to the system
when operating system software is not running. The console
subsystem consists of the following components:
console program
console terminal
console terminal port
remote access device
remote access port
Ethernet ports
Glossary6
console terminal
The video or hardcopy terminal used to start the system and
direct activities between the computer operator and the console
subsystem.
console terminal port
The connector to which the console terminal cable is attached.
controller
A system component, usually a printed circuit board, that
regulates the operation of one or more devices.
CPU
See central processing unit.
cursor
A blinking symbol on the screen that indicates where the next
character you type will appear.
CXT
Integral 2D accelerated graphics.
cycle
One clock interval.
data
A formal representation of information suitable for
communication, interpretation, and processing by humans
or computers.
data bus
A pathway used to carry data signals between two or more
components of the system.
data transmission
The movement of data in the form of electrical signals along a
communications line.
Glossary7
database
A collection of interrelated data on one or more mass storage
devices. The collection is organized to facilitate efficient and
accurate inquiry and update.
D-cache
Data cache. A high-speed memory reserved for the storage of
data. Contrast with I-cache.
DEChip 21064
The systems main processor running various cycle times.
DECnet network
Digital networking software that runs on nodes in both local and
wide area networks.
DEC OSF/1 AXP operating system
A general-purpose operating system based on the Open Software
Foundation OSF/1 1.0 technology. DEC OSF/1 AXP runs on the
range of AXP systems, from workstations to servers.
DECwindows Motif
An interface to the operating system that allows a workstation
screen to be divided into windows where several application
programs can appear simultaneously, and commands can be
executed using menus and a mouse. This interface is fully
compliant with the OSF/Motif Graphical User Interface standard
from the Open Software Foundation. See also window.
default
A computer value or setting that is automatically in effect unless
or until another value is specified. There are some default values
that you cannot override.
default recovery action
The action that the system takes after a power or system failure.
desktop enclosure
A type of system cabinet that is small enough to sit on top of a
desk. Compare with floorstand and rackmount enclosure.
Glossary8
depth of image
The number of bits per pixel in a frame buffer.
device
The general name for a hardware unit connected to the system
that is capable of receiving, storing, or transmitting data. An
example of a device is a fixed disk drive; you can install a fixed
disk drive into the system unit or into an expansion box that you
then connect to the system unit.
device name
The name by which a device or controller is identified in the
system. The name that a particular operating system uses for a
storage device to access that particular device. Also called the
device mnemonic.
diagnostics
Programs, located in read-only memory, that detect and identify
abnormal system hardware operation.
digital data
Information recorded and transmitted in binary coded form.
direct memory access
A processor that transfers data directly from one memory to
another without going through the main processor.
disc
See compact disc.
disk
A flat circular plate with a magnetic coating on which data is
magnetically stored in concentric circles (tracks). A fixed disk
resides permanently inside a disk drive, whereas a diskette is
removable.
disk drive
A device that holds a disk. The drive contains mechanical
components that spin the disk and move the read and write
heads that store and read the information on the surface of the
disks.
Glossary9
diskette
A disk contained in a square jacket. Diskettes can be inserted
and removed from diskette drives.
diskette drive
A disk drive that reads from or writes to a removable diskette,
such as an RX26 diskette.
diskless system
A system that has no storage capacity of its own.
DMA
See direct memory access.
DRAM
See dynamic random-access memory.
drive bracket
A bracket that holds a removable-media drive, such as the RX26,
or a fixed disk drive, such as the RZ25 or RZ26 drives.
dynamic random-access memory
Read/write memory that must be refreshed (read from or written
to) periodically to maintain the storage of information.
environment variable
A global data structure that can be accessed only from console
mode. The setting of these data structures determines how
a system powers up, boots operating system software, and
operates.
error line
A line of information that appears if a self-test or a power-up test
fails. The following information appears on the error line: Field
replaceable unit (FRU) number; component number; component
mnemonic; error message number.
Example: 001 9 NI 172
error message number
A number that appears on the error line representing a
particular system or component problem.
Glossary10
Ethernet
A local area network (LAN) or wide area network (WAN) that
connects (by coaxial cable) multiple computers that are running
a variety of network operating systems. Ethernet transmits
10 megabits per second and does not require switching logic or
control by a central computer.
Ethernet controller
An interface unit that connects a system to the Ethernet.
Ethernet hardware address
The unique Ethernet physical address associated with a
particular Ethernet communications controller.
Ethernet ports
The connectors on the system unit through which the Ethernet
is connected to the system.
Ethernet subsystem
The Ethernet controller chip built into the system module.
expansion box
An option that can be attached to your system that holds one
or more TURBOchannel option modules, hard disk drives, and
removable-media drive.
Factory-Installed Software (FIS)
Operating system software that is loaded into an internal fixed
disk and installed in the system unit during manufacture. On
site, the FIS is bootstrapped through the system disk, prompting
a predefined menu of questions on the final configuration.
fatal error
An error from which a process cannot recover. Fatal errors are
either those that cause the CPU to stop, or disk-write errors that
occur at any time except when the disk drive is being powered
down or write-locked.
FDDI
See Fiber Distributed Data Interface
Glossary11
FEPROM (flash-erasable programmable read-only memory)

A memory device from which data can be erased in large
amounts at a time. If the FEROM code does not correspond
to the CPU code, you receive an error message and you must
update the flash ROM.
Fiber Distributed Data Interface
An ANSI-standard high-speed network technology that uses
fiber optics as the transmission medium. FDDI employs a ring
topology and operates up to 100 km in total network length. It
uses 1300 nm wavelengths, which optimize fiber bandwidth.
field replaceable unit (FRU) number
A Digital number allocated to any component or module that can
be replaced by you or your Digital service representative.
file
A collection of related information treated by the system as a
unit.
filler panel
A blank panel that covers the slot for the removable-media drive
when the removable-media drive is not installed in the system.
The RX26 removable-media drive has its own front panel, which
permits the user to access the front of the drive.
firmware
Software code that is stored in a fixed way (wired in), usually in
read-only memory. The firmware executes when the system is
turned on, during operating system boot and restarts, and as a
result of operator intervention or a fatal system error.
The firmware code provides a number of basic functions on your
system, including the console program and diagnostic testing.
The Firmware Update Utility lets you update your system with
new software code whenever it is available from Digital.
FIS
See Factory Installed Software.
Glossary12
fixed disk
A disk that resides permanently inside a disk drive. Compare
with diskette.
fixed disk drive
The drive that holds and reads from or writes to a fixed disk.
frame buffer
An area of memory that contains a pixel-level description of a
displayed image. The frame buffer is also used to refresh the
raster display.
gigabyte (GB)
The measure used to refer to memory or secondary storage
capacity, equal to 1,024 megabytes or 1,073,741,824 bytes.
graphics
The use of lines, figures, shapes, and shaded areas to display
information.
graphics heads
Multiple monitors connected to one system unit through the use
of a second and third graphics module.
ground
A conducting connection to an electrical circuit that is at zero
potential relative to the earth; a voltage reference point that has
a zero voltage potential. Ground should be at the same potential
as neutral. Each dedicated circuit should contain a neutral and
green ground wire.
half-height disk
Any 1 5/8-inch fixed drive that is 3 inches (9-centimeters) wide,
such as those in the RZ family; or a 1 5/8-inch removable drive
that is 5-inches (12.7-centimeters) wide, such as a compact disc.
Glossary13
halt
The action of stopping the CPU from processing. This action
brings the system under the control of the console program. A
halt can occur when an internal system error is detected, when
you enter the HALT command at the console terminal, or when
you press the Halt button on the back of the system unit.
hard error
A nonrecoverable error.
hardware
The physical equipmentmechanical and electricalthat makes
up a system. Compare with software.
hexadecimal
A numbering system using the base 16 that is a shorthand
method for representing binary numbers. Using this method,
each four bits is converted into a single hexadecimal digit. For
example, 1001 in binary form is equal to 9 in hexadecimal form.
hexword
A length of 256 bits, 16 words, 8 longwords, or 32 bytes.
icon
A graphical symbol appearing on the system that identifies
drives, ports, switches, and indicators.
initialization
The sequence of steps that prepare the system to start.
Initialization occurs automatically after a system has been
turned on.
I-cache
Instruction cache. A high-speed memory reserved for the storage
of instructions. Contrast with D-cache.
input/output (I/O) device
A piece of equipment that transmits data to (input) and from
(output) the system. For example, a terminal or a mouse. See
mouse.
Glossary14

An international telecommunications standard that allows a
communications channel to simultaneously carry voice, video,
and data.
interactive communication
A method of communicating with the computer. In an interactive
session, you enter a command at the keyboard and the system
executes the command and then prompts you for another
command.
interface
An electronic circuit board that links an external device to a
computer. Also, a device or piece of software that allows a user
to communicate with the system or allows the components of the
system to communicate with each other.
ISDN
See Integrated Services Digital Network.
jack
A receptacle into which you insert a plug, such as an audio jack.
(Compare with port.)
kilobyte (KB)
The measure used to refer to memory or secondary storage
capacity, equal to 1,024 bytes.
LAN
See local area network.
LANCE
Local-area network controller for Ethernet.
latency
The amount of time it takes the system to respond to an event.
Glossary15
light-emitting diode (LED)

A semiconductor device that glows when supplied with a specific
voltage. The DEC 3000 Model 300 Series AXP system module
contains eight LEDs that indicate the status of the modules in
the system.
local
In close proximity to the computer. Compare with remote.
local area network
A high-speed network communications system that connects a
variety of multiple computers within a limited geographical area,
such as one building or a group of buildings. It is a privately
owned communication network whose speed is upward of one
megabit per second. Using a LAN, multiple users can share
devices and files at higher speeds, faster response times, and
lower costs than with telephone lines.
local area system
A type of configuration in which cluster information is carried
out over the Ethernet by software that emulates certain
computer interconnect (CI) port functions.
local device
A disk drive, tape drive, or other device that is only available to
the computer to which it is connected.
log in
To identify yourself to the operating system. When you log
in, you type an account name and password. If the name and
password match an account on the system, you are allowed
access to that account.
logic
A sequence of hardware or software operations. Hardware logic
consists of chips and circuits that compute and control computer
operations. Software logic (also called program logic) is the
sequence of program instructions.
Glossary16
login command
The command issued at the operating system prompt that allows
access to and communication with the system.
longword
Four contiguous bytes (32 bits) starting on any addressable byte
boundary. Bits are numbered from right to left, 0 through 31.
The address of the longword is the address of the byte containing
0. A naturally aligned longword has an address evenly divisible
by 4.
loopback connector
An Ethernet or communications connector used on the back of
the system unit when testing the Ethernet subsystem or the
synchronous/asynchronous communications adapter.
loopback tests
Diagnostic tests used to isolate a failure by testing segments of a
particular control or data path.
machine check
An operating system action triggered by certain system
hardware-detected errors that can be fatal to system operation.
Once triggered, machine-check handler software analyzes the
error.
Maintenance Operations Protocol
The transport protocol for network bootstraps and other network
operations.
mass storage device
An input/output device on which data is stored. Typical mass
storage devices include fixed disks, compact discs, magnetic
tapes, and diskettes.
Mb
See megabit.
MB
See megabyte.
Glossary17
media
The physical material on which data is recorded, for example,
magnetic disks, diskettes, and compact discs.
megabit
A unit of measure equal to a million bits.
megabyte
A unit of measure equal to 1,024 kilobytes or 1,048,576 bytes.
memory
The area of the system that electrically stores instructions and
data, often temporarily.
memory module
A single in-line memory module (SIMM) that contains memory
for your system. Memory modules come in different sizes, each
with a different amount of memory.
millions of instructions per second (MIPS)
A unit of measure for recording the execution rate of a computer,
for example .5 MIPS is equal to 500,000 instructions per second.
mnemonic
The abbreviation used by the system to identify a device or
controller in the system. Also referred to as the device name.
modem
A device that converts computer signals to signals that can be
sent over a telephone line.
module
An etched circuit board that contains electrical components and
electrically conductive pathways between components on which
logic devices (such as transistors, resistors, and memory chips)
are mounted. A module stores data or memory or controls the
functions of a device.
monitor
A video device that displays data.
Glossary18
monochrome frame buffer

A separate memory component for black and white graphics.
MOP
See Maintenance Operations Protocol.
mouse
A hand-held input device that is moved across the desktop to
move the pointer or cursor on the monitor screen and to select
menu options and draw graphics. The mouse is palm-sized and
contains up to three buttons (function keys).
multiprocessing system
A system that executes multiple tasks simultaneously.
network
Two or more computers linked by communication lines to share
information and resources.
Network Interconnect (NI)
A high-speed bus that interconnects systems and serves as the
primary means of communication between them; for example,
Ethernet.
network manager
The person who manages the network, assigns unique node
names and addresses for each system on the network, and
provides administrative assistance to network users.
node
A device that has an address on, is connected to, and is able
to communicate with other devices on the bus. In a computer
network, an individual computer system connected to the
network that can communicate with other systems on the
network.
node name
A name that identifies a unique node.
Glossary19
nonvolatile random-access memory (NVR)

Memory, such as magnetic tape or core memory, in which values
are stored even when the system is turned off. NVR codes
represent continued power-on testing. If an error occurs during
this testing sequence, then a hexadecimal code is displayed along
with FRU and error code information
ns
See nanoseconds.
online documentation
Documents that can be read directly on your monitor screen.
Online documentation is stored on a compact disc and includes
all text and illustrations found in the printed manuals. Fast
access time and cross-referencing are two advantages of online
documentation.
Open Software Foundation (OSF)
A foundation formed to develop a new operating system based
on the UNIX standard. Part of the Open Software Foundations
charter is to provide an interface for developing portable
applications that run on a variety of hardware platforms.
open system
A system that implements open specifications for interfaces,
services, and supporting formats so that applications software
can:
Be ported across a wide range of systems with minimal

changes
Interoperate with other applications on local and remote

systems
Interact with users in a style that facilitates user portability
OpenVMS AXP operating system

Digitals open version of the VMS operating system, which runs
on DEC 3000 machines. See also open system.
Glossary20
operating system
An integrated collection of programs that controls the operation
of the system and allows users access to data files, input/output
devices, and application programs. The DEC 3000 Model
300 Series AXP system runs the OpenVMS and DEC OSF/1
operating systems.
operating system mode
The state in which the system console terminal is under the
control of the operating system software. Also called program
mode.
PAL
See Privileged Architecture Library (software).
PALcode
Privileged Architecture Library code, written to support DEC
3000 AXP processors. PALcode implements architecturally
defined behavior.
parameter
A variable given a specific value that is passed to a program
before execution. The system console code uses many such
parameters.
parity
A method for checking the accuracy of data by calculating the
sum of the number of ones in a piece of binary data. Even
parity requires the correct sum to be an even number, odd parity
requires the correct sum to be an odd number.
password
A unique string of characters or numbers, or both that identifies
you to the computer.
password security feature
The feature that restricts access to certain console commands.
To use all console commands, users must enter a password.
Glossary21
peripheral device
An internal or external device that provides the central
processing unit (CPU) with additional memory storage or
communication capability. Examples are disk and diskette
drives, video terminals, printers, and expansion boxes.
pointing device
A terminal input device that allows you to make a selection from
a menu or to draw graphics. See mouse and tablet.
port
A socket on the front or back of the system unit to which a
terminal, printer, modem or other device is connected. (Compare
with jack.)
port pin-outs
The description of the function of electronic signals transmitted
through each pin in a port connector.
power-up
The sequence of events that occur when you supply power to the
system for the first time.
Privileged Architecture Library (PAL)
A software chip that has a series of logic gates (AND, OR, and
NOT) that are not tied together.
privileged console commands
The commands allowed by the password security feature. See
also password security feature.
privileged console mode
The state the system is in when the password security feature
is enabled. When the system is in this mode, certain console
commands can be issued only after a password is provided. See
also password security feature.
program
The sequence of instructions the system uses to perform a task.
See also software.
Glossary22
program mode
The state in which the computer is controlled by the operating
system. After the operating system is invoked, the system
always operates in program mode, unless you put it into console
mode. In program mode, the user can manage the system, run
software applications, and perform network tasks. Compare with
console mode.
prompt
A symbol or message displayed by a program or an operating
system, asking you to provide input.
puck
A palm-sized device that slides on a tablets surface. The puck
and tablet together function as a pointing device. See also
pointing device and tablet.
quadword
Eight contiguous bytes starting on an arbitrary byte boundary.
The bits are numbered from right to left, 0 through 63.
random access memory (RAM)
Memory that can be both read from and written to and that
can randomly access any one location during normal operations.
The type of memory the system uses to store the instructions of
programs currently being run.
read-only memory (ROM)
Memory that cannot be modified. The system can use (read) the
data contained in ROM but cannot change it.
Reduced Instruction Set Computer
A computer with an instruction set that is reduced in complexity,
but not necessarily in the number of instructions. RISC
architectures typically require more instructions than Complex
Instruction Set Computer (CISC) architectures to perform given
operations, because an individual RISC instruction performs less
work than a CISC instruction.
Glossary23
register
A temporary storage location in hardware logic other than main
memory.
reliability
The probability that a device or system will not fail to perform
its intended functions during a specified time when operated
under stated conditions.
remote
Physically distant from a computer, but linked to a computer by
communication lines. Compare with local.
removable-media drive
An external or internal drive such as the RRD42, TZK10, TZ30,
TLZ06, or RX26 from which the storage medium is removable.
restore
In software, to recover files or software that were backed up,
copying the material from the backup medium (such as a tape
or diskette) to the medium you normally use. In hardware, to
return the system to an operating condition.
RISC
See Reduced Instruction Set Computer.
ROM
See read-only memory.
satellite
A node that is booted remotely from the system disk on the
boot node. Also, a computer system that obtains a specific set of
services from a server system.
SCSI
See Small Computer System Interface.
Glossary24
SCSI bus
A communications pathway between the Small Computer System
Interface (SCSI) and other internal devices. The SCSI bus
consists of an address bus, which selects the location of the data,
and a data bus, which transfers the data.
SCSI controller
The device that directs the operations of the Small Computer
System Interface (SCSI) with synchronous and asynchronous
capabilities.
SCSI ID
The switch or jumper setting that identifies the address of each
device installed on the system. Each device must have a unique
SCSI ID for proper communication between the system and the
device.
SCSI jumpers
Removable electrical connectors on some of the drives, such as
the RRD42, that are set to determine the SCSI ID on a drive.
Each installed drive must have a unique setting for proper
communication between the system and all drives.
SCSI switches
Electrical switches on the side or back of some drives, such
as the RX26, that determine the SCSI setting of the drive.
Each installed drive must have a unique setting for proper
communication between the system and all drives.
secure system jumper
An electrical jumper in the system unit that you can move so
that the system is accessible to only those with the correct
password.
self-test
A test that is invoked automatically when the system starts up.
Serial Communication Controller (SCC)
The DEC 3000 Model 300 Series AXP I/O subsystem includes
two SCC chips that control the mouse, keyboard, and serial
communications.
Glossary25
serial port
A port dedicated to hookups with serial line devices such as
terminals or printers. Serial devices transmit data one word
after another (serially) along a single pair of lines from a sending
device to a receiving device.
server
Hardware or software that provides a specific set of services to a
satellite or client. See also client-server computing.
Small Computer System Interface (SCSI)
An ANSI-standard interface designed for connecting disks and
other peripheral devices to computer systems. SCSI is used by
many computer and peripheral vendors throughout the industry.
smart frame buffer
A separate memory component for graphics images.
software
Instructions executed by the system to perform a chosen or
required function. Compare with hardware.
standalone network
A network that starts and operates alone, without being
connected to another network.
standalone workstation
A workstation that starts and operates alone, without being
connected to another computer.
standard Ethernet network
An Ethernet network connected with standard Ethernet cable.
(Also known as thickwire Ethernet). Compare with ThinWire
Ethernet network.
storage array
A group of mass storage devices, frequently configured as one
logical disk.
Glossary26
storage device
A device, such as a diskette or tape, capable of recording
information.
storage expansion box
See expansion box.
strain relief strap
See universal strain relief strap.
stylus
A penlike device that draws on the surface of a tablet and
functions as a pointing device.
synchronous communication
A type of communication in which data is transmitted at equal
time intervals. This type of communication allows you to connect
your system to others in one of two ways:
Through a modem to a Wide Area Network (WAN)
Directly to another system through a null modem
system
A combination of hardware, software, and peripheral devices
that together perform specific processing operations.
system module
A circuit board that provides interface connectors to the memory
modules.
system configuration
The combined layout of hardware and software that makes up a
usable computer system.
system disk
The device on which operating system software resides.
system unit
The part of the system that contains the drives, memory, power
supply, and the computer itself.
Glossary27
tablet
An absolute-positioning input device composed of a flat-surfaced
digitizing tablet that functions as a drawing surface. Two
pointing devices, a puck and a stylus, are used with the tablet to
move the cursor on the monitor screen, draw graphics, and make
selections from the menu.
tape cartridge
Housing for magnetic tape. The cartridge contains a reel of tape
and a take-up reel. A cartridge is similar to a cassette, but of
slightly different design.
tape drive
A device containing mechanical components that holds, turns,
reads, and writes on magnetic tape.
terminal
A device for entering information into a computer system and
displaying it on a screen. A typewriter-like keyboard, mouse,
tablet or other pointing device is used to enter information.
terminator
A connector used on one or both ends of an Ethernet segment
that provides the 50-ohm termination resistance needed for the
cable. A terminator is also required on unused ports and on the
end of a SCSI bus to complete the bus.
ThinWire Ethernet network
A Digital trademark used to describe its 10BASE2 Ethernet
products. See also 10BASE2.
time-of-year clock (TOY)
The t[est] toy command verifies that the Time-Of-Year clock
has been set, and that it is ticking.
turn off
The sequence of steps that stops the flow of electricity to a
system or its components.
twisted-pair Ethernet network
See 10BASE-T Ethernet network.
Glossary28
TURBOchannel module
High-performance interconnection hardware that allows you to
use a variety of Digital and third-party graphics, multimedia,
and communications options. The TURBOchannel module is
a synchronous asymmetrical I/O channel that connects option
modules to the system module. With this connection, the system
module and an option module have read or write access to
each other, but option modules have no access to other option
modules.
TURBOchannel extender
See expansion box.
two-dimensional graphics
Images that are displayed on the screen in 2D. These
graphics require the use of the HX 8-plane smart frame buffer
TURBOchannel graphics option or the TX 24-plane color 2D
option, which supports motion video.
universal strain relief strap
A plastic strap used when connecting the monitor video cable
to the back of the monitor. The strap prevents the weight of
the cable junction block from pulling the cables out of the BNC
connectors.
user interface
The style of interaction between the computer and the user of
that computer.
video refresh rate
The speed at which the image on the screen is restored.
volatile memory
Memory from which values are lost when the system is turned
off.
WAN
See wide-area network.
Glossary29
wide-area network
A high-speed public or private data communications system that
connects multiple users in different geographical areas, such as
different cities or states. In a WAN, transmissions are carried
primarily over telephone lines.
window
An area on your monitor screen in which you can start, run, and
view a separate process. Windowing capability is supported by
both OpenVMS and DEC OSF/1 workstation software.
word
Two contiguous bytes (16 bits) starting on an addressable byte
boundary. Bits are numbered from right to left, 0 through 15. A
word is identified by the address of the byte containing bit 0.
work group
Several workstations, connected together on a network, that
perform similar tasks and share information or databases.
workstation
A single-user system that offers high-performance,
high-resolution graphics, and can function in a network
environment.
write-enabled
The condition that enables a tape or diskette to be written to.
Compare with write-protected.
wrist strap
See antistatic wrist strap.
write-protected
The condition that prevents a tape or diskette from being
accidentally overwritten.
Z buffer
A buffer that attaches a depth value to every pixel to determine
which parts of an image must be discarded from processing or be
hidden from view.
Glossary30
Index
A
Acoustical specifications for system, A5

Adding options
external, xi
internal, xi
two methods, 22
Alternate console
access via the network, 66
change internal jumper, 65
connecting a printer or terminal, 63
connecting to system, 63
disconnect the keyboard, 64
jumper, 65
port specifications, 64
restarting the system, 66
when to use, 62
Antistatic precautions, 218
Antistatic wrist strap
attaching, 218
removing, 255
Associated documentation, D1
Audio
features, 112
port pinouts, C6
Cable approval, system module, F6

Cables
for drive in position 1, 230
for drive in position 2, 231
internal power, 219
removing from power supply, 246
RX26 removable-media drive, 225
SCSI, 220
supported for system module, F7
Communications
port pinouts, C8
ports, C1
Compact disc drive, 35
loading an operating system, 35
Components, system, 12
Configuration
checking, 23, 26, 210, 259
comparing old and new, 259
display, 23, 26, 210
error message, 28
memory, 234
reviewing, 23, 26, 210
show config command, 26, 259
show device command, 23
show mem command, 210
Console commands
boot, 48
continue, 415
deposit, 416, 57
examine, 420
halt, 424
help, 425
B
Backing up files, 214
10BASE-T, port pinouts, C4
boot command, 48
default boot flags, 410
parameters, 48
qualifiers, 48
Index1
Console commands (contd)

initialize, 429
login, 430, 56
privileged, 52
repeat, 431
set, 432
set auto_action, 438
set bootdef_dev, 438
set boot_osflags, 438
set boot_reset, 439
set diag_quick, 440
set diag_section, 440
set enable_audit, 441
set language, 441
set mop, 443
set password, 443
set radix, 444
set scsi_reset, 444
set secure, 443
set trigger, 444
show, 445
show bootdef_dev, 449
show boot_osflags, 450
show boot_reset, 450
show config, 26, 28, 259, 451
show device, 23, 24, 25, 451
show diag_loe, 452
show diag_quick, 452
show diag_section, 452
show enable_audit, 453
show error, 453
show ethernet, 454
show language, 454
show mem, 210, 211, 455
show mop, 455
show radix, 456
show scsi_a, 457
show scsi_reset, 457
show secure, 456
show trigger, 457
start, 458
test, 23, 459
using, 41
Index2
Console mode
definition of, 43
continue command, 415
Conventions
device names, 411
used in this guide, xii
Cover
removing, 217
replacing, 255
CPU module
handling, 244, 245
installing, 245
removing, 244
Customer diagnostic environment, 46
D
Debugging programs, E1
examining the impure area, E2
examining the machine check logout area,
E3
memory-based data structures, E1
DEC OSF/1 AXP operating system, 17
end user documentation, D4
DECsound application, 112
DECspin application, 112
deposit command, 416, 57
Device names
conventions for, 411
examples of, 412
Devices, testing configuration of, 259
Diagnostic display lights, 82
location, 82
recording, 83
Diagnostic environment
console, 46
customer, 46
power-up, 46
service, 47
Diagnostic test displays, 23
Digital Support Centers
telephone numbers, xiv
Dimensions of system, A2
Disk Erase Utility, 232

Disk Verify Utility, 232, 464
Diskette
caution - corrupting device, 463
Diskette Formatter Utility, 227, 463
Documentation, D1
DEC 3000/4000 firmware, D3
DEC OSF/1 AXP end user, D4
drives, D3
for Model 300 series, xv
miscellaneous, D5
OpenVMS AXP, D5
printed, D1
SCSI, D4
Sound and Motion J300, D2
TURBOchannel-related, D2
Drives
documentation, D3
getting status of installation, 23
E
Environmental limitations for system, A4
Equipment
turning off, 215
turning on, 257
Erase Disk Utility, 232
erasing a fixed disk, 462
Error messages
console mode, 43
during startup, 260
FRU error codes, 85
recording, 260
show config command, 259
show error command, 453
software, 78
Errors, solving configuration, 210
Ethernet ROM
removing and installing, 250
examine command, 420
Expansion boxes, 34
connection to system, 36
turning on, 257
External connections to system unit, 36

External options
adding, 212
expansion box, 34
headset, 32
modem, 33
printer, 33
puck and pen, 32
RRD42 compact disc drive, 35
tablet, 32
F
Factory-installed software (FIS), 18
Files, backing up, 214
Filler panel
adding, 224
installing, 224
removing, 224, 225
Filler plate, removing from TURBOchannel
slot, 242
Firmware
parameters, 113
purpose of, 114
understanding the effect of changes, 113
update utility, 114
FIS
See factory-installed software
Fixed disk
erasing, 232
erasing data from, 462
verify utility, 232, 464
Fixed disk drive
adding RZ25, 212
adding RZ25L, 212
adding RZ26, 212
adding RZ26L, 212
installing, 212, 232
removing, 227, 228
removing mounting bracket, 229
RZ25 specifications, B6
RZ25L specifications, B12
RZ26L specifications, B18
Index3
Fixed disk drive (contd)

SCSI jumper settings, 232
Formatting a diskette, 227, 463
FRU error codes, 86
Future options, 16
G
Graphics options
HX with DEC OSF/1 AXP, 110
HX with OpenVMS AXP, 19
HX+ with DEC OSF/1 AXP, 110
multiple, 19
TX with DEC OSF/1 AXP, 110
with DEC OSF/1 AXP, 19
with OpenVMS AXP, 19
H
halt command, 424
Hardware
shutting down, 215
specifications, A1
Headset, 32
help command, 425
Host power rating, system module, F3
I
initialize command, 429
Input devices
puck and pen, 32
tablet, 32
Installation of options
checking, 257
required tools, 22
time required, 22
Internal options
CPU module, 244, 245
Ethernet ROM, removing, 250
fixed disk drive, 212, 227, 232
memory, 233, 237
power supply, 246, 249
removable-media, 212, 222, 226
specifications, B1
system module, 252, 254
Index4
Internal options (contd)

TURBOchannel, 238, 240, 242
Internal power cable, 219
ISDN
Australian connections, 111
availability, 111
B channels, 111
capabilities, 111
D channels, 112
port pinouts, C5
J
Jumpers
alternate console, 65
firmware update, 114
RZ25 fixed disk drive, B9, B16
RZ25L fixed disk drive, B13
RZ26 fixed disk drive, B16
secure system, 55
K
Keyboard
disconnect for alternate console, 64
troubleshooting problems, 77
Keyboard/mouse
port pinouts, C7
L
LEDs
See Diagnostic display lights
Location of options, 221
Log in to the system, 56
login command, 430, 56
M
Memory module, 233
8-MB SIMMs, 235
32-MB SIMMs, 235
configuration rules, 234
installing, 237
Memory module (contd)

removing, 236
status of installation, 210
Memory-based data structures, E1
Metal shield, installing, 224
Modem
description, 33
turning on, 257
Module isolation, system module, F3
Monitor
moving, 216
turning on, 257
Mounting bracket
removing from fixed disk drive, 229
Mouse
Multimedia Services
multimedia software, 112
Multiple graphics capabilities, 19
N
Network
access to alternate console, 66
Networked systems
shutting down, 214
O
Open Software Foundation, 17
OpenVMS AXP, 17
documentation, D5
features, 17
Operating systems, 17
DEC OSF/1 AXP, 17
loading from a compact disc drive, 35
OpenVMS AXP, 17
shutting down, 214
Options
external, 212, 31
future, 16
graphics, 19
installation time, xi
internal, 22
Options (contd)
See also External options, 22, 212
See also Internal options, 22
specifications, B1
status of options installation, 26
testing connection, 259
P
Password
changing, 57
disabling, 58
enabling, 54
entering, 53
erasing, 57
error message, 54
forgetting, 54
Port pinouts
audio, C6
10BASE-T, C4
ISDN, C5
keyboard/mouse, C7
SCSI, C2
synchronous/asynchronous
communications, C8
table of, C1
tablet, C7
Ports
safety warnings for UK, F5
Power
internal cable, 219
requirements for system, A2
Power supply
installing, 249
removing, 246, 248
removing cable, 246
Power-up
diagnostic environment, 46
Preparing your system
overview, 213
Printers, 33
turning on, 257
using as alternate console, 63
Index5
Privileged commands, 52
Problems
identifying, 71
worksheet, 812
Product description, 12
Program mode
definition of, 43
Programs, debugging, E1
Puck and pen devices, 32
R
Removable-media device
formatting a diskette, 463
installing, 226
installing filler panel, 224
removing, 222
removing drive, 222
removing filler panel, 225
SCSI switch settings, 223
Removable-media drive
RX26 diskette specifications, B3
RX26 drive specifications, B2
repeat command, 431
Restarting the system, 257
RRD42 compact disc drive, 35
loading an operating system, 35
RX26 removable-media drive
checking switches, B4
diskette specifications, B3
drive performance, B3
drive specifications, B2
drive storage capacity, B4
installing, 212
SCSI ID, B2
SCSI switches, B4
RZ25 fixed disk drive
adding, 212
J5 SCSI ID selection, B10
jumpers, B9, B16
setting SCSI ID, B6
specifications, B6
Index6
RZ25L fixed disk drive

adding, 212
jumpers, B13
setting SCSI ID, B12
specifications, B12
adding, 212
SCSI ID selection, B16
specifications, B15
RZ26l fixed disk drive
specifications, B18
RZ26L fixed disk drive
adding, 212
jumpers, B19
jumpers, B22
specifications, B21
S
Safety warnings, system module, F4
SCSI
cable, 220
device overview, 212
documentation, D4
introduction to IDs, 213
port pinouts, C2
switches, 223, B4
SCSI devices
external drives, 212
fixed disk drives, 232
removable-media drive, 212, 223
RZ25 fixed disk drive, 212
RZ25L fixed disk drive, 212
RZ26 fixed disk drive, 212
RZ26L fixed disk drive, 212
SCSI Erase Utility
See test command, 462
SCSI ID
RX26 removable-media drive, B2, B4
verifying, 259
SCSI port, C2
Security feature
See System security feature
Service diagnostic environment, 47
Service specifications, system module, F2
set command, 113, 432
auto_action variable, 113, 433, 438
bootdef_dev variable, 113, 433, 438
boot_osflags variable, 433, 438
boot_reset variable, 434, 439
diag_loe variable, 434
diag_quick variable, 113, 434, 440
diag_section variable, 434, 440
enable_audit variable, 435, 441
language variable, 435, 441
list of environment variables, 433
list of values, 433
mop variable, 435, 443
password variable, 436, 443
radix variable, 436, 444
scsi_reset variable, 436, 444
secure variable, 437, 443
trigger variable, 437, 444
show command, 445
auto_action variable, 446
bootdef_dev variable, 446, 449
boot_osflags variable, 446, 450
boot_reset variable, 446, 450
config variable, 446, 451
device variable, 451
diag_loe variable, 446, 452
diag_quick variable, 447, 452
diag_section variable, 452
enable_audit variable, 447, 453
environment variables, 446
error variable, 447, 453
ethernet variable, 454
language variable, 447, 454
show command (contd)

list of parameters, 449
list of qualifiers, 449
mem variable, 455
mop variable, 448, 455
radix variable, 448, 456
scsi_a variable, 457
scsi_reset variable, 448, 457
secure variable, 448, 456
trigger variable, 448, 457
values, 446
show config command, 26, 259
display, 26
display description, 26
display, errors, 29
error description, 28
show device command, 23, 451
display, 24
display description, 25
example, 24
show mem command, 210
description of, 211
display, 211
example, 211
Shutting down
hardware, 215
networked systems, 214
operating systems, 214
Sound and Motion J300
documentation, D2
Specifications
internal options, B1
RX26 removable-media, B3
RX26 removable-media drive, B2
start command, 458
Starting up system, 257
Static discharge
preventing, 218
Index7
Storage expansion boxes, 34

Switches
RX26 removable-media drive, B4
Synchronous/asynchronous communications
port pinouts, C8
System
components, 12
configuration, 23, 26, 210
configuration error, 28, 210
connecting alternate console, 63
external connections, 36
location of internal devices, 221
logging in, 56
making secure, 53
removing cover, 218
replacing cover, 255
restarting after resetting alternate console
jumper, 66
restoring, 255
specifications, A2
starting, 258
testing, 259
turning off, 215
turning on, 257
System cover
installing filler panel, 224
installing metal shield, 224
removing, 217
removing filler panel, 224, 225
removing metal shield, 225
replacing, 255
System module
cable approval for UK, F6
connecting to a digital circuit, F8
Ethernet ROM, removing, 250
host power rating, F3
installing, 254
module isolation, F3
removing, 252, 253
safety warnings for UK, F4
service specifications, F2
supported cables, F7
Index8
System preparation
backing up files, 214
moving the monitor, 216
opening system unit, 216
overview, 213
removing the system cover, 217
shutting down networks, 214
shutting down operating systems, 214
turning off equipment, 215
System security feature, 53
changing a password, 57
disabling a password, 58
enabling password, 54
entering a password, 53
erasing a password, 57
purpose, 51
secure system jumper, 54
System specifications
acoustical, A5
environmental, A4
general, A3
power, A2
weight and dimensions, A2
System unit
opening, 216
removing cover, 217
replacing cover, 255
T
Tablet, 32
port pinouts, C7
Terminal
using as alternate console, 63
test command, 459
diagnostic displays, 23
Tools, required, 22
Troubleshooting, 260
diagnostic display lights, 82, 83
keyboard problems, 77
monitor problems, 75
mouse/tablet problems, 76
network problems, 78
problems worksheet, 812
Troubleshooting (contd)
SCSI device problems, 77
system problems, 73
tables, 72
TURBOchannel
definition of, 238
options, 239, 240, 242
related documentation, D2
removing filler plate, 242
Turning off equipment, 215
Turning on equipment, 257
U
Utilities
Disk Verify, 232
Diskette Formatter, 227
Erase Disk, 232
Firmware Update, 114
W
Warranty coverage, 22
Weight of system, A2
Wrist strap
attaching, 218
removing, 255
Index9

Dec 3000 m300 Manual

Uploaded by

Copyright:

Available Formats

Dec 3000 m300 Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dec 3000 m300 Manual

Uploaded by

Copyright:

Available Formats

DEC 3000 Model 300 Series AXP

Hardware Reference Guide

Digital Equipment Corporation, Maynard, MA

Second Printing, January 1994

This document was prepared using VAX DOCUMENT Version 2.1.

1 Introduction to Your System

2 Adding, Removing, and Replacing Internal Options

3 Connecting External Options

4 Using Console Commands

5 Using the Password Security Feature

6 Using an Alternate Console Device

7 Troubleshooting by Visual Inspection

B Internal Options: Specifications and SCSI ID Settings

F Supplementary Information for PTT Network Users

Guide to DEC 3000 Model 300 Series AXP

Cabling a Drive in Position 1 . . . . . . . . . . . . . . . . .

Telephone Numbers of Digital Support Centers . . . . . . . . .

This guide describes how to:

Remove and replace internal options

Connect external options

Use console commands to run tests and utilities, and to set

Set the password security feature

Connect and use an alternate console

Identify and solve problems

This guide also provides system and option specifications, port

You can add internal options by:

Adding the options yourself.

Having a Digital service representative add them.

You can add external options to your system, by connecting them

The following conventions are used in this guide:

A key name is shown enclosed to indicate

The console program does not distinguish

A word in this typeface indicates a

Lowercase italicized letters in commands

The information contained within these

The information contained within these

Quotation marks indicate a literal string.

Options/qualifiers are identified by a dash

Warnings contain information to prevent

Cautions provide information to prevent

Digital Services representatives are available for on-site support

Table 1 lists the Digital Support Center contact numbers. If a

Figure 1 is a guide to the DEC 3000 Model 300 Series AXP

Figure 1 Guide to DEC 3000 Model 300 Series AXP

To get the system

For Digital Services

The DEC 3000 Model 300 Series AXP system is a

This chapter covers the following topics:

Integrated Services Digital Network (ISDN)

System Personalization Capabilities

Firmware Update Utility

Figure 11 shows the system and its components.

Table 11 System Features

DEC OSF/1 AXP;

150 Mhz - model 300

100 Mhz - model 300L

One or two additional

(continued on next page)

Table 11 (Cont.) System Features

PXG+ 8-plane 3D Z-buffer