Initial Print Date: 02/2000 Revision Date: 6/2000

Subject Page
M54 Engine
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Mechanical changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Performance Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Review Questions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Siemens MS 43.0 System
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
I - P - O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
MS 43.0 New functions
Electronic throttle Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Accelerator Pedal Sensor (PWG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Electronic Throttle Valve (EDK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Main Relay Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Engine Optimized Ignition Key OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Diagnosis Module Tank Leakage (DM-TL) . . . . . . . . . . . . . . . . . . . . . . .17
DM-TL Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
DM-TL Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Carry Over Functions
Inputs
Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Camshaft Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Crankshaft Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Misfire Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
OBD Fault Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Mass Air Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Outputs
VANOS Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Electric Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Secondary Air Injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Engine Speed Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
RZV Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Resonance - Turbulence Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Idle Speed control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Purge Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Table of Contents
M54 ENGINE
Models: E53 X5,
SOP: 3 liter - 4/00
Objectives of the Module:
Purpose of the System:
The M54 engine was developed to meet the needs for ULEV compliancy for emission con-
trol. The increase in displacement allows the engine to fit the X5 All Roads vehicle while still
meeting the demands for power and performance.
INTRODUCTION
The M54 - 6 cylinder engine is being introduced with the 2001 Model Year E53 - X5. The
displacement of the new engine for the X5 is 3 liters and the engine will replace the 2.8 liter
engine in the E46/Z3 series in 6/2000 and E39 series vehicles in 9/2000.
.
Design objectives for the M54 engine were to provide:
Lower Emissions
Maintain Fuel Economy
Maintain Power and Performance levels
2
M54engMS43/ST036/6/2000
At the end of this section of the handout, you will be able to:
Identify the changes to the M54 engines over the M52 TU engine.
List the design objectives for the M54 engine.
M54 ENGINE
M54B30
HORSE POWER 225@5900RPM
TORQUE 300Nm@3500RPM
BORE 84mm
STROKE 89.6mm
COMPRESSION 10.2:1
3
M54engMS43/ST036/6/20000
ART-A0021216
M54 ENGINE
Mechanical Changes
In addition to the increased displacement of the M54B30 engine, several mechanical
changes were incorporated into the engine for reduced emissions and increased fuel econ-
omy. These changes include:
NEW PISTONS - The piston has a shorter skirt compared to the M52 TU and continues
with the graphite coating for friction and emission reducing measures. The piston rings have
been modified to reduce friction.
CRANKSHAFT - The crankshaft for the 3 liter M54 is adopted from the S52B32 - M3
engine.
CAMSHAFT - The camshaft for the 3 liter M54 is modified with more lift (9.7 mm) and
new valve springs to accommodate the increased lift.
INTAKE MANIFOLD - The intake manifold is modified with shorter ram tubes (20mm
shorter on 3 liter. The diameter of the tubes is increased slightly.
INJECTION VALVES - The diameter of the injection pintle has increased slightly for the
increased displacement of the 3 liter engine.
4
M54engMS43/ST036/6/2000
ART-0198U29
ART-INJECTOR
M54 ENGINE
MECHANICAL CHANGES
NON RETURN FUEL RAIL SYSTEM
The M54 engine with MS 43.0 control uses the non return fuel rail system introduced on
the M62 TU engine. The system meets running loss compliance without the use of the 3/2-
way solenoid valve currently used on the M52 TU engine.
The regulated fuel supply is controlled by
the fuel pressure regulator integrated in
the fuel filter. The fuel return line is also
located on the filter.
The M54 engine uses an Electronic Controlled
Throttle Valve (EDK) for intake air control. The
idle control valve and turbulence function of the
intake manifold carries over from the M52 TU
engine.
5
M54engMS43/ST036/6/20000
ART-FUELRAIL
M54B30 ENGINE
6
M54engMS43/ST036/6/2000
ART-HPCHARTB30.
225
7
M54engMS43/ST036/6/20000
REVIEW QUESTIONS
1. What is the major reason for the development of the M54 engine?
__________________________________________________________________________
2. What are the major mechanical changes that were integrated into the3 liter M54 engine?
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
___________________________________________________________________________
8
M54engMS43/ST036/6/2000
SIEMENS ENGINE MANAGEMENT SYSTEM
Models: E53 X5
SOP: 3 liter - 4/00
Objectives of the Module:
At the end of this section of the handout you will be able to:
Identify the changes that have occurred to the MS 43 system compared to the MS 42
Describe the operation of the new inputs
Describe the operation of the new outputs
Discuss which new components/subsystems relate directly to ULEV compliancy
This new generation Siemens system is designated as MS 43.0.
Siemens MS 43.0 is a newly developed engine management system to meet the needs of
Ultra Low Emission Vehicle (ULEV) compliancy and continuing with present systems is also
OBD II compliant. This system also includes control of the Motor-driven Throttle Valve
(EDK).
The ECM uses a pc-board dual-processor control unit in the SKE housing configuration.
The MS 43.0 ECM is flash programmable as seen with previous systems.
ECM hardware includes:
Modular plug connectors featuring 5 connectors in the SKE housing with 134 pins.
Connector 1 = Supply voltages and grounds
Connector 2 = Peripheral signals (oxygen
sensors, CAN, etc.)
Connector 3 = Engine signals
Connector 4 = Vehicle signals
Connector 5 = Ignition signals
Special features:
Flash EPROM which is adaptable to several M52 LEV engines and has the capability to
be programmed up to 13 times
Once a control unit is installed and coded to a vehicle it cannot be swapped with anoth-
er vehicle for diagnosing or replacement (because of EWS 3.3).
9
M54engMS43/ST036/6/20000
SYSTEM OVERVIEW I-P-O
Service
Engine
Soon
ART-IPO46X.EPS
10
M54engMS43/ST036/6/2000
MS 43 NEW FUNCTIONS
ELECTRONIC THROTTLE SYSTEM - EML
The M54 engine with MS 43 engine control uses an electronic throttle control system
adopted from the ME 7.2 system on the M62 engine. The system incorporates an electric
throttle valve (EDK) and pedal position sensor (PWG) for engine power control.
The MS 43 control module monitors the PWG input and activates the EDK motor based on
the programmed maps for throttle control. The MS 43 module self checks the activation of
the EDK via feedback potentiometers motor on the EDK motor.
Additional functions of the EML system include:
Cruise control function
DSC throttle interventions
Maximum engine and road speed control
ART-SCANDIAGRAM
11
M54engMS43/ST036/6/20000
MS 43 NEW FUNCTIONS
ACCELERATOR PEDAL SENSOR
The accelerator pedal sensor is similar to the PWG used on the ME 7.2 system. It is inte-
grated into the accelerator pedal housing. Two hall sensors are used to provide the drivers
input request for power.
The hall sensors receive power (5 volts) and ground from the MS 43 control module and
produce linear voltage signals as the pedal is pressed from LL to VL.
PWG SENSOR 1 = 0.5 to 4.5 V
PWG SENSOR 2 = 0.5 to 2.0 V
The MS 43 control module uses the
signal from sensor 1 as the drivers
request and the signal from sensor 2
as plausibility checking.
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
HS
1 2 3 4 5
MS 43.0
HS
S
I
G
N
A
L

1
S
I
G
N
A
L

2
HALL SENSOR
POWER
61460015
12
M54engMS43/ST036/6/2000
MS 43 NEW FUNCTIONS
ACCELERATOR PEDAL SENSOR
PWG SIGNAL MONITORING & PWG FAILSAFE OPERATION:
As a redundant safety feature the PWG provides two separate signals from two integral
angle hall sensors (HS #1 and HS #2) representing the drivers request for throttle acti-
vation.
If the monitored PWG signals are not plausible, MS 43.0 will only use the lower of the
two signals as the drivers pedal request input providing failsafe operation. Throttle
response will be slower and maximum throttle position will be reduced.
When in PWG failsafe operation, MS 43.0 sets the EDK throttle plate and injection time
to idle (LL) whenever the brake pedal is depressed.
When the system is in PWG failsafe operation, the instrument cluster matrix display will
post Engine Emergency Program and PWG specific fault(s) will be stored in memory.
_____________________________________________________________________________
_____________________________________________________________________________
E46ICPOT-SIG.
13
M54engMS43/ST036/6/20000
MS 43 NEW FUNCTIONS
EDK THROTTLE POSITION FEEDBACK SIGNALS
The EDK throttle plate is monitored by two integrated potentiometers. The potentiometers
provide linear voltage feedback signals to the control module as the throttle plate is opened
and closed.
Feedback signal 1 provides a signal from 0.5 V (LL) to 4.5 V (VL).
Feedback signal 2 provides a signal from 4.5 V (LL) to 0.5 V (VL)
Potentiometer signal 1 is the primary feedback signal of throttle plate position and signal 2
is the plausibility cross check through the complete throttle plate movement.
ART-EDK.EPS1
ART-E46ICPWG2.
14
M54engMS43/ST036/6/2000
MS 43 NEW FUNCTIONS
EDK THROTTLE POSITION FEEDBACK SIGNALS
EDK FEEDBACK SIGNAL MONITORING & EDK FAILSAFE OPERATION:
The EDK provides two separate signals from two integral potentiometers (Pot 1 and Pot
2) representing the exact position of the throttle plate.
EDK Pot 1 provides the primary throttle plate position feedback. As a redundant safe-
ty feature, Pot 2 is continuously cross checked with Pot 1 for signal plausibility.
If plausibility errors are detected between Pot 1 and Pot 2, MS 43.0 will calculate the
inducted engine air mass (from HFM signal) and only utilize the potentiometer signal that
closely matches the detected intake air mass.
- The MS 43.0 uses the air mass signalling as a virtual potentiometer (pot 3) for a
comparative source to provide failsafe operation.
- If MS 43.0 cannot calculate a plausible conclusion from the monitored pots (1 or 2
and virtual 3) the EDK motor is switched off and fuel injection cut out is activated
(no failsafe operation possible).
The EDK is continuously monitored during all phases of engine operation. It is also
briefly activated when KL 15 is initially switched on as a pre-flight check to verify its
mechanical integrity (no binding, appropriate return spring tension, etc). This is accom-
plished by monitoring both the motor control amperage and the reaction speed of the
EDK feedback potentiometers. If faults are detected the EDK motor is switched off and
fuel injection cut off is activated (no failsafe operation possible). The engine does how-
ever continue to run extremely rough at idle speed.
When a replacement EDK is installed, the MS 43.0 adapts to the new component
(required amperage draw for motor control, feedback pot tolerance differences, etc).
This occurs immediately after the next cycle of KL 15 for approximately 30 seconds.
During this period of adaptation, the maximum opening of the throttle plate is 25%.
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
15
M54engMS43/ST036/6/20000
MS 43 NEW FUNCTIONS
MAIN RELAY MONITOR
The MS 43.0 system incorporates a new monitoring feature for terminal 87 (KL 87) of the
main relay. The relay is monitored internally for the voltage level at KL 87. Five seconds after
the ignition key is switched on, and the voltage at the KL 15 input is greater than 9 volts,
the control module checks the voltage at KL 87.
If the voltage difference between the two terminals is greater than 3 volts, a fault will be
stored in the ECM.
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
ART-E46ICMS43RELAY
16
M54engMS43/ST036/6/2000
MS 43 NEW FUNCTIONS
EMISSION OPTIMIZED - IGNITION KEY OFF
Emission Optimized Ignition Key Off is a programmed feature of the MS 43 control mod-
ule.
After the ECM detects KL 15 being switched OFF, the ignition stays active for two more
individual coil firings. This means that just two cylinders are fired - not two revolutions.
This feature allows residual fuel injected into the cylinders, as the ignition key is switched
off, to be burned as the engine runs down.
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
ART-E46ICEMIOPT
17
M54engms43/STO36/6/2000
MS 43 NEW FUNCTIONS
DM-TL (DIAGNOSIS MODULE - TANK LEAKAGE)
The M54 engine with the Siemens MS43.0 engine control system uses the DMTL system
for fuel system leakage monitoring. The pump is manufactured by Bosch for use with the
Siemens control system.
18
M54engms43/STO36/6/00
1
2 3
DM-TL (DIAGNOSIS MODULE - TANK LEAKAGE)
FUNCTIONAL OVERVIEW:
The DM-TL is located in the drivers side rear wheel well in the X5 and next to the charcoal
canister on the E46 - M54.
1. In its inactive state, filtered fresh air enters the evaporative system through the sprung
open valve of the DM-TL.
2. When the DME activates the DM-TL for leak testing, it first activates only the pump
motor. This pumps air through a restrictor orifice (1.0 or 0.5 mm) which causes the elec-
tric motor to draw a specific amperage value. This value is equivalent to the size of the
restrictor.
3. The solenoid valve is then energized which seals the evap system and directs the pump
output to pressurize the evap system.
The evap system is detected as having a large leak if the amperage value is not realized, a
small leak if the same reference amperage is realized or no leak if the amperage value is
higher than the reference amperage.
19
M54engMS43/ST039/3/17/00
DM-TL (DIAGNOSIS MODULE - TANK LEAKAGE)
FUNCTION
The DC Motor LDP ensures accurate fuel system leak detection for leaks as small as
0.5mm (.020). The pump contains an integral DC motor which is activated directly by the
engine control module. The ECM monitors the pump motor operating current as the mea-
surement for detecting leaks.
The pump also contains an ECM controlled change over valve that is energized closed dur-
ing a Leak Diagnosis test. The change over valve is open during all other periods of oper-
ation allowing the fuel system to breath through the inlet filter (similar to the full down
stroke of the current vacuum operated LDP).
20
M54engMS43/ST039/3/17/00
LEAK DIAGNOSIS TEST PRECONDITIONS
The ECM only initiates a leak diagnosis test every second time the criteria are met. The cri-
teria is as follows:
Engine OFF with ignition switched OFF.
Engine Control Module still in active state or what is known as follow up mode (Main
Relay energized, control module and DME components online for extended period after
key off).
Prior to Engine/Ignition switch OFF condition, vehicle must have been driven for a min-
imum of 20 minutes.
Prior to minimum 20 minute drive, the vehicle must have been OFF for a minimum of 5
hours.
Fuel Tank Capacity must be between 15 and 85% (safe approximation between 1/4 -
3/4 of a tank).
Ambient Air Temperature between -7
O
C & 35
O
C (20
O
F & 95
O
F )
Altitude < 2500m(8,202 feet).
Battery Voltage between 11.5 and 14.5 Volts
When these criteria are satisfied every second time, the ECM will start the Fuel System Leak
Diagnosis Test. The test will typically be carried out once a day i.e. once after driving to
work in the morning, when driving home in the evening, the criteria are once again met but
the test is not initiated. The following morning, the test will run again.
21
M54engMS43/ST039/3/17/00
LEAK DIAGNOSIS TEST
PHASE 1 - REFERENCE MEASUREMENT
The ECM activates the pump motor. The pump pulls air from the filtered air inlet and pass-
es it through a precise 0.5mm reference orifice in the pump assembly.
The ECM simultaneously monitors the pump motor current flow . The motor current raises
quickly and levels off (stabilizes) due to the orifice restriction. The ECM stores the stabilized
amperage value in memory. The stored amperage value is the electrical equivalent of a 0.5
mm (0.020) leak.
22
M54engMS43/ST039/3/17/00
PHASE 2 - LEAK DETECTION
The ECM energizes the Change Over Valve allowing the pressurized air to enter the fuel sys-
tem through the Charcoal Canister, The ECM monitors the current flow and compares it
with the stored reference measurement over a duration of time.
Once the test is concluded, the ECM stops the pump motor and immediately de-energizes
the change over valve. This allows the stored pressure to vent thorough the charcoal can-
ister trapping hydrocarbon vapor and venting air to atmosphere through the filter.
23
M54engMS43/ST039/3/17/00
TEST RESULTS
The time duration varies between 45 & 270 seconds depending on the resulting leak diag-
nosis test results (developed tank pressure amperage / within a specific time period).
However the chart below depicts the logic used to determine fuel system leaks.
24
M54engMS43/ST036/6/2000
MS 43 CARRY OVER FUNCTIONS
INPUT FUNCTIONS
BOSCH OXYGEN SENSORS
The MS43.0 system uses Bosch LSH 25 oxygen sensors that function basically the same
as previously used (in Bosch systems). The voltage range is between 0 - 800 mV.
The location remains the same with the pre-cat sensors are mounted on top of the exhaust
manifolds. The catalysts are now integral with the exhaust manifolds (further detailed in the
M52 TU engine section).
PRE 02 SENSOR POST 02 SEN-
SOR
POST-CATALYST
SENSORS
25
M54engMS43/ST036/6/20000
OXYGEN SENSOR SIGNAL INFLUENCE ON INJ ECTOR OPEN TIME
The ECM monitors the:
Amplitude of the signal (highest voltage or range sensor is producing)
Switching time of the signal (how fast from lean to rich)
Frequency of complete cycles (how many within a period of time)
These characteristics provide info to the ECM that reflect the overall condition of the sen-
sor.
POST CATALYTIC CONVERTER SENSOR SIGNAL
The post catalyst O2 sensors monitor the efficiency of the catalyst as a requirement of OBD
II. This signal also provides feedback of the pre-catalyst sensors efficiency and can cause
the ECM to trim the ms injection time to correct for slight deviations.
If the catalyst is operating efficiently, most of the remaining oxygen in the exhaust gas
is burned (lack of O2 - constant lean signal).
The sensor signal fluctuates slightly in the higher end of the voltage scale.
If the post sensor shows excessive fluctuations (which echo the scope pattern of the pre
sensor), this indicates that the catalytic converter is not functioning correctly and cannot
consume the O2 (fault set).
If the post sensor fluctuations move out of the normal voltage window, this indicates
that the pre sensor is not performing properly due to slight deterioration. These systems
can also trim the ms injection time to compensate for this.
The constantly changing oxygen sensor input to the ECM is needed to correct the ms
injection time to ensure that the ideal air/fuel ratio is maintained.
26
M54engMS43/ST036/6/2000
CAMSHAFT SENSOR
-INTAKE AND EXHAUST CAMSHAFTS
The "static" Hall sensors are used so that the camshaft positions are recognized once igni-
tion is on - even before the engine is started.
The function of the intake cam sensor:
Cylinder bank detection for preliminary injection
Synchronization
Engine speed sensor (if crankshaft speed sensor fails)
Position control of the intake cam (VANOS)
The exhaust cam sensor is used for position control of the exhaust cam (VANOS)
If these sensors fail there are no substitute values, the system will operate in the failsafe
mode with no VANOS adjustment. The engine will still operate, but torque reduction will be
noticeable.
NOTE: Use caution on repairs as not to bend the impulse wheels
K L 1 5
K L 1 5
M S 4 2 . 0
SOLENOID
OIL TEMP.
SENSOR
TWO POSITION PISTON HOUSING
WITH INTERNAL/EXTERNAL
HELICAL GEAR CUP
TWO POSITION PISTON
HOUSING WITH
INTERNAL/EXTERNAL
HELICAL GEAR CUP
ENGINE
OIL SUPPLY
VENT
VENT
SOLENOID
SENSOR
SENSOR
M S 4 2
E C M
E XH A U S T
I N TA K E
M S 4 2 . 0
E C M
MS 43.0
MS 43.0
MS 43.0
27
M54engMS43/ST036/6/20000
CRANKSHAFT SENSOR
The crankshaft sensor is a dynamic Hall-effect sensor (mounted through the engine block),
the signal is sent the moment the crankshaft begins to rotate.
The pulse wheel is mounted directly to the crankshaft as seen on previous models.
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
MS 43.0
SMOOTH RUNNING ENGINE
NOTE SQUARE WAVE
ENGINE MISFIRE DETECTED
28
M54engMS43/ST036/6/2000
MISFIRE DETECTION
As part of the CARB/OBD regulations the engine control module must determine if misfire
is occurring and also identify the specific cylinder(s) and the severity of the misfire event,
and whether it is emissions relevant or catalyst damaging. In order to accomplish these
tasks the control module monitors the crankshaft for acceleration losses during firing seg-
ments of each cylinder based on firing order.
Misfire Detection Example: M54 (6 Cyl.) with Siemens System
The misfire/engine roughness calculation is derived from the differences in the period dura-
tion (T) of individual increment gear segments. Each segment period consist of an angular
range of 120 crank angle that starts 78 before Top Dead Center (TDC).
If the expected period duration is greater than the permissible value a misfire fault for the
particular cylinder is stored in the fault memory of the ECM. Depending on the level of mis-
fire rate measured the control unit will illuminate the "Service Engine Soon" light, may cut-
off fuel to the particular cylinder and may switch lambda operation to open-loop. All mis-
fire faults are weighted to determine if the misfire is emissions relevant or catalyst damag-
ing.
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
29
M54engMS43/ST036/6/20000
EMISSIONS RELEVANT:
During an interval of 1000 crankshaft revolutions the misfire events of all cylinders are
added and if the sum is greater than a predetermined value a fault will be set identifying the
particular cylinder(s). The Service Engine Soon light will be illuminated during and after
the second cycle if the fault is again present.
CATALYST DAMAGING:
During an interval of 200 crankshaft revolutions the misfire events of all cylinders are added
and if the sum is greater than a predetermined value a fault will be set identifying the par-
ticular cylinders(s). The Service Engine Soon lamp:
On vehicles with a Siemens Control Module (M54 engines) - the lamp will immediately go
to a steady illumination since fuel to the injector(s) is removed. Fuel cut-off to the cylin-
der will resume after several (>> 7) periods of decel if crankshaft sensor adaptation is suc-
cessfully completed or the engine is shut-off and restarted.
In each case the number of misfire events permitted is dependent on engine speed, load
and temperature map.
The process of misfire detection continues well after the diagnostic drive cycle requirements
have been completed. Misfire detection is an on-going monitoring process that is only dis-
continued under certain conditions.
Misfire detection is only disabled under the following conditions:
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
REQUIREMENTS STATUS/CONDITION
Engine Speed < 512 RPM
Engine Load Varying/Unstable
Throttle Angle Varying/Unstable
Timing Timing retard request active (i.e. knock
control - ASC, AGS)
Engine Start-up Up to 5 seconds after start-up
A/C Up to 0.5 seconds after A/C activation
Decel fuel cut-off Active
Rough road recognition Active
ASC Control Active
30
M54engMS43/ST036/6/2000
F
A
I
L
E
D
C
O
M
P
O
N
E
N
T
P
O
S
S
I
B
L
E

F
A
U
L
T

M
I
S
F
I
R
E
E
F
F
E
C
T
/
L
O
C
A
T
I
O
N
C
a
m
s
h
a
f
t
b
r
o
k
e
n
m
o
s
t

l
i
k
e
l
y

m
o
r
e

t
h
a
n

o
n
e
c
y
l
i
n
d
e
r

a
f
f
e
c
t
e
d
P
i
s
t
o
n
h
o
l
e

i
n

p
i
s
t
o
n

c
r
o
w
n
/
p
i
s
t
o
n
s
e
i
z
e
d

i
n

b
o
r
e
o
n

t
h
e

a
f
f
e
c
t
e
d

c
y
l
i
n
d
e
r
s
H
y
d
r
a
u
l
i
c

l
a
s
h

a
d
j
u
s
t
e
r
s
(
H
V
A
)
d
e
f
e
c
t
i
v
e
:

i
.
e
.

o
i
l

b
o
r
e
r
e
s
t
r
i
c
t
e
d
/
b
l
o
c
k
e
d
o
n

t
h
e

a
f
f
e
c
t
e
d

c
y
l
i
n
d
e
r
s
e
n
g
i
n
e

o
i
l

p
r
e
s
s
u
r
e

b
u
i
l
t

u
p
t
o
o

s
l
o
w
F
u
e
l

p
r
e
s
s
u
r
e
f
u
e
l

p
u
m
p
,

p
r
e
s
s
u
r
e

t
o
o

l
o
w
m
o
s
t

l
i
k
e
l
y

c
y
l
.

1
-
3

(
f
r
o
n
t
c
y
l
i
n
d
e
r
s
)
f
u
e
l

f
i
l
t
e
r

r
e
s
t
r
i
c
t
e
d
/

b
l
o
c
k
e
d
m
o
s
t

l
i
k
e
l
y

c
y
l
.

1
-
3

(
f
r
o
n
t
c
y
l
i
n
d
e
r
s
)
f
u
e
l

p
u
m
p
,

p
r
e
s
s
u
r
e

b
u
i
l
d

u
p
t
o
o

s
l
o
w

a
f
t
e
r

s
t
a
r
t
m
o
s
t

l
i
k
e
l
y

c
y
l
.

1
-
3

(
f
r
o
n
t
c
y
l
i
n
d
e
r
s
)
l
e
a
k
i
n
g

f
u
e
l

f
e
e
d

l
i
n
e
s
m
o
s
t

l
i
k
e
l
y

c
y
l
.

1
-
3

(
f
r
o
n
t
c
y
l
i
n
d
e
r
s
)
p
r
e
s
s
u
r
e

r
e
g
u
l
a
t
o
r

d
e
f
e
c
t
i
v
e
(
m
e
t
a
l

f
i
l
i
n
g
)
m
o
s
t

l
i
k
e
l
y

c
y
l
.

1
-
3

(
f
r
o
n
t
c
y
l
i
n
d
e
r
s
)
r
u
n
n
i
n
g

l
o
s
s

v
a
l
v
e

d
e
f
e
c
t
i
v
e
m
o
s
t

l
i
k
e
l
y

c
y
l
.

1
-
3

(
f
r
o
n
t
c
y
l
i
n
d
e
r
s
)
f
u
e
l

t
a
n
k

e
m
p
t
y
m
o
s
t

l
i
k
e
l
y

c
y
l
.

1
-
3

(
f
r
o
n
t
c
y
l
i
n
d
e
r
s
)
s
i
p
h
o
n

j
e
t

p
u
m
p

a
n
d

f
u
e
l
t
a
n
k

e
m
p
t
y
m
o
s
t

l
i
k
e
l
y

c
y
l
.

1
-
3

(
f
r
o
n
t
c
y
l
i
n
d
e
r
s
)
w
a
t
e
r

i
n

f
u
e
l

t
a
n
k
m
o
s
t

l
i
k
e
l
y

m
o
r
e

t
h
a
n

o
n
e
c
y
l
i
n
d
e
r

a
f
f
e
c
t
e
d
F
u
e
l
h
i
g
h

c
o
n
t
e
n
t

o
x
y
g
e
n
a
t
e
d
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
n
o
n

a
n
t
i

c
a
r
b
o
n

a
d
d
i
t
i
v
e
s
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
O
x
y
g
e
n

s
e
n
s
o
r
e
x
c
e
s
s
i
v
e

m
i
x
t
u
r
e

d
e
v
i
a
t
i
o
n
o
n
l
y

t
h
e

a
f
f
e
c
t
e
d

b
a
n
k
P
u
r
g
e

s
y
t
e
m
e
x
c
e
s
s
i
v
e

r
i
c
h

m
i
x
t
u
r
e

d
u
e
t
o

h
i
g
h

a
m
b
i
e
n
t

t
e
m
p
e
r
a
t
u
r
e
o
n
e

o
r

m
o
r
e

b
a
n
k
s
b
l
o
c
k
e
d

f
u
e
l

t
a
n
k

v
e
n
t

i
n
l
e
t
a
l
l

c
y
l
i
n
d
e
r
s
C
r
a
n
k

s
e
n
s
o
r
/
i
n
c
r
e
m
e
n
t
w
h
e
e
l
i
n
c
o
r
r
e
c
t

i
n
p
u
t

s
i
g
n
a
l

f
o
r
m
i
s
f
i
r
e

d
e
t
e
c
t
i
o
n
a
l
l

c
y
l
i
n
d
e
r
s
i
n
c
r
e
m
e
n
t

w
h
e
e
l

l
o
o
s
e
a
l
l

c
y
l
i
n
d
e
r
s
i
n
c
r
e
m
e
n
t

w
h
e
e
l

d
a
m
a
g
e
d
a
f
f
e
c
t
e
d

s
e
g
m
e
n
t
g
a
p

b
e
t
w
e
e
n

s
e
n
s
o
r

a
n
d
i
n
c
r
e
m
e
n
t

w
h
e
e
l
a
f
f
e
c
t
e
d

s
e
g
m
e
n
t
f
l
y

w
h
e
e
l

d
a
m
a
g
e
d
C
a
t
a
l
y
s
t

d
a
m
a
g
e
d
e
x
h
a
u
s
t

b
a
c
k

p
r
e
s
s
u
r
e

o
n
t
h
e

a
f
f
e
c
t
e
d

b
a
n
k
o
n
l
y

t
h
e

a
f
f
t
e
c
t
e
d

b
a
n
k
D
M
E
f
i
n
a
l

s
t
a
g
e

i
g
n
t
i
o
n
/
i
n
j
e
c
t
o
r
s
a
l
l

c
y
l
i
n
d
e
r
F
A
I
L
E
D
C
O
M
P
O
N
E
N
T
P
O
S
S
I
B
L
E

F
A
U
L
T

M
I
S
F
I
R
E
E
F
F
E
C
T
/
L
O
C
A
T
I
O
N
S
p
a
r
k

p
l
u
g
e
l
e
c
t
r
o
d
e

g
a
p

t
o
o

s
m
a
l
l
a
f
f
e
c
t
e
d

c
y
l
i
n
d
e
r
s
e
l
e
c
t
r
o
d
e
s

m
i
s
s
i
n
g
a
f
f
e
c
t
e
d

c
y
l
i
n
d
e
r
s
e
l
e
c
t
r
o
d
e
s

o
i
l
/
f
u
e
l

s
o
a
k
e
d
a
f
f
e
c
t
e
d

c
y
l
i
n
d
e
r
s
e
l
e
c
t
r
o
d
e
s

o
i
l
/
f
e
u
l

s
o
a
k
e
d
f
o
u
l
e
d
s
p
a
r
k

p
l
u
g

c
e
r
a
m
i
c

b
r
o
k
e
n
a
f
f
e
c
t
e
d

c
y
l
i
n
d
e
r
s
o
i
l

l
e
v
e
l

t
o
o

h
i
g
h
m
o
s
t

l
i
k
e
l
y

m
o
r
e

t
h
a
n
o
n
e

c
y
l
i
n
d
e
r

a
f
f
e
c
t
e
d
o
i
l

f
o
a
m
i
n
g
o
i
l

l
e
v
e
l

t
o
o

h
i
g
h
,

o
i
l
/
f
u
e
l

f
o
u
l
e
d
h
e
a
t

r
a
n
g
e

t
o
o

c
o
l
d
c
r
a
n
k

c
a
s
e

v
e
n
t
i
l
a
t
i
o
n

d
e
f
e
c
t
i
v
e
m
o
s
t

l
i
k
e
l
y

m
o
r
e

t
h
a
n
o
n
e

c
y
l
i
n
d
e
r

a
f
f
e
c
t
e
d
S
p
a
r
k

p
l
u
g

c
o
n
n
e
c
t
o
r
w
e
t
,

w
a
t
e
r

o
r

m
o
i
s
t
u
r
e
m
o
s
t

l
i
k
e
l
y

m
o
r
e

t
h
a
n
o
n
e

c
y
l
i
n
d
e
r

a
f
f
e
c
t
e
d
b
r
o
k
e
n
a
f
f
e
c
t
e
d

c
y
l
i
n
d
e
r
s
I
g
n
i
t
i
o
n

C
o
i
l
i
n
t
e
r
n
a
l

d
e
f
e
c
t
,

a
r
c
i
n
g
a
f
f
e
c
t
e
d

c
y
l
i
n
d
e
r
s
C
o
n
n
e
c
t
o
r
s

i
g
n
i
t
i
o
n
c
o
r
r
o
s
i
o
n
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
p
i
n

b
a
c
k
e
d

o
u
t
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
p
l
u
g

l
o
o
s
e
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
l
o
o
s
e

w
i
r
e

f
r
o
m

c
o
n
n
e
c
t
o
r
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
I
n
j
e
c
t
i
o
n

V
a
l
v
e
m
e
t
a
l

f
i
l
i
n
g
o
n

t
h
e

a
f
f
e
c
t
e
d
c
y
l
i
n
d
e
r
s
l
e
a
k
i
n
g
o
n

t
h
e

a
f
f
e
c
t
e
d
c
y
l
i
n
d
e
r
s
c
a
r
b
o
n

f
o
u
l
e
d
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
d
i
r
t
y
/
c
o
n
t
a
m
i
n
a
t
e
d
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
I
n
j
e
c
t
o
r

c
o
n
n
e
c
t
o
r
s
c
o
r
r
o
s
i
o
n
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
p
i
n

b
a
c
k
e
d

o
u
t
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
p
l
u
g

l
o
o
s
e
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
l
o
o
s
e

w
i
r
e

f
r
o
m

c
o
n
n
e
c
t
o
r
o
n
e

o
r

m
o
r
e

c
y
l
i
n
d
e
r
s
I
n
t
a
k
e

m
a
n
i
f
o
l
d

l
e
a
k
s
i
n
t
a
k
e

p
l
e
n
u
m
,

u
n
m
e
t
e
r
e

a
i
r
l
e
a
k


(
i
.
e
.

i
n
j
e
c
t
o
r

s
e
a
l
s
)
I
n
t
a
k
e
/
E
x
h
a
u
s
t

v
a
l
v
e
c
a
r
b
o
n

b
u
i
l
t

u
p

(
i
n
t
a
k
e
)
m
o
s
t

l
i
k
e
l
y

m
o
r
e

t
h
a
n
o
n
e

c
y
l
i
n
d
e
r

a
f
f
e
c
t
e
d
b
u
r
n
t

o
r

d
a
m
a
g
e
d
o
n

t
h
e

a
f
f
e
c
t
e
d
c
y
l
i
n
d
e
r
s
o
v
e
r
r
e
v
:
i
n
t
a
k
e

o
r

e
x
h
a
u
s
t
v
a
l
v
e
s

l
e
a
k
i
n
g

(
b
e
n
t
)
m
o
s
t

l
i
k
e
l
y

m
o
r
e

t
h
a
n
o
n
e

c
y
l
i
n
d
e
r

a
f
f
e
c
t
e
d
O
B
D

I
I

-

M
i
s
f
i
r
e

F
a
u
l
t
s
31
M54engMS43/ST036/6/20000
MASS AIR FLOW SENSOR HFM
The Siemens mass air flow sensor is functionally the same as in the past. The designation
2 Type B simply indicates that it is smaller in design. The mass air meter has a diameter of
85 mm.
________________________________________________________________
________________________________________________________________
________________________________________________________________
32
M54engMS43/ST036/6/2000
MS 43 CARRY OVER FUNCTIONS
OUTPUT FUNCTIONS -VANOS CONTROL
With the double VANOS system, the valve timing is changed on both the intake and the
exhaust camshafts.
Double VANOS provides the following benefits:
Torque increase in the low to mid (1500 - 2000 RPM) range without power loss in the
upper RPM range.
Less incomplete combustion when idling due to less camshaft overlap (also improves
idle speed characteristics).
Internal exhaust gas recirculation (EGR) in the part load range (reduces NOx and post-
combustion of residual gasses in the exhaust)
Rapid catalyst warm up and lower raw emissions after cold start.
Reduction in fuel consumption
Double VANOS consists of the following parts:
Intake and exhaust camshafts with helical gear insert
Sprockets with adjustable gears
VANOS actuators for each camshaft
2 three-way solenoid switching valves
2 impulse wheels for detecting camshaft position
2 camshaft position sensors (Hall effect)
The initial timing is set by gear positioning (refer to the Repair Instructions for details) and
the chain tensioner. As with the previous VANOS, the hydraulically controlled actuators
move the helical geared cups to regulate camshaft timing. The angled teeth of the helical
gears cause the pushing movement of the helical cup to be converted into a rotational
movement. This rotational movement is added to the turning of the camshafts and cause
the camshafts to advance or retard. The adjustment rate is dependent oil temperature,
oil pressure, and engine RPM.
33
M54engMS43/ST036/6/20000
NOTE: With extremely hot oil temperatures Vanos is deactivated (Power loss). If the oil is
too thick (wrong viscosity) a fault could be set.
When the engine is started, the camshafts are in the failsafe position (deactivated). The
intake camshaft is in the RETARDED position - held by oil pressure from the sprung open
solenoid. The exhaust camshaft is in the ADVANCED position - held by a preload spring in
the actuator and oil pressure from the sprung open solenoid.
After 50 RPM (2-5 seconds) from engine start, the ECM is monitoring the exact camshaft
position.
The ECM positions the camshafts based on engine RPM and the throttle position signal.
From that point the camshaft timing will be varied based on intake air and coolant temper-
atures.
The double VANOS system is fully variable. When the ECM detects the camshafts are in
the optimum positions, the solenoids are modulated (approximately 100-220 Hz) maintain-
ing oil pressure on both sides of the actuators to hold the camshaft timing.
CAUTION: The VANOS MUST be removed and installed exactly as described in the Repair
Instructions!
NOTE: If the VANOS camshaft system goes to the failsafe mode (deactivated) there will be
a noticeable loss of power. This will be like driving with retarded ignition or starting from a
stop in third gear.
K L 1 5
K L 1 5
M S 4 2 . 0
SOLENOID
OIL TEMP.
SENSOR
TWO POSITION PISTON HOUSING
WITH INTERNAL/EXTERNAL
HELICAL GEAR CUP
TWO POSITION PISTON
HOUSING WITH
INTERNAL/EXTERNAL
HELICAL GEAR CUP
ENGINE
OIL SUPPLY
VENT
VENT
SOLENOID
SENSOR
SENSOR
M S 4 2
E C M
E XH A U S T
I N TA K E
M S 4 2 . 0
E C M
MS 43.0
MS 43.0
MS 43.0
EXHAUST: Advanced
piston moved in
INTAKE: Retard piston
moved out
EXHAUST: Advanced
piston moved out
INTAKE: Retard piston
moved in
DEACTIVATED
KL 15
KL 15
MS42.0
SOLENOID
OIL TEMP.
SENSOR
TWO POSITION PISTON HOUSING
WITH INTERNAL/EXTERNAL
HELICAL GEAR CUP
TWO POSITION PISTON
HOUSING WITH
INTERNAL/EXTERNAL
HELICAL GEAR CUP
ENGINE
OIL SUPPLY
VENT
VENT
SOLENOID
SENSOR
SENSOR
MS42
ECM
EXHAUST
INTAKE
MS42.0
ECM
ACTIVATED
KL 15
KL 15
MS42.0
SOLENOID
OIL TEMP.
SENSOR
TWO POSITION PISTON HOUSING
WITH INTERNAL/EXTERNAL
HELICAL GEAR CUP
TWO POSITION PISTON
HOUSING WITH
INTERNAL/EXTERNAL
HELICAL GEAR CUP
ENGINE
OIL SUPPLY
VENT
VENT
SOLENOID
SENSOR
SENSOR
MS42
ECM
EXHAUST
INTAKE
MS42.0
ECM
MS 43.0
MS 43.0
MS 43.0
MS 43.0
MS 43.0
MS 43.0
34
M54 engMS43/STO36/6/2000
35
M54engMS43/ST036/6/20000
The dual VANOS in conjunction with the variable intake manifold provides an additional
emission control feature.
Because of the improved combustion, the camshaft timing is adjusted for more overlap.
The increased overlap supports internal exhaust gas recirculation (EGR) which reduces
tailpipe emissions and lowers fuel consumption.
During the part load engine range, the intake camshaft overlap opens the intake valve. This
allows limited exhaust gas reflow the intake manifold.
The internal EGR reduces the cylinder temperature thus lowering NOx. This feature pro-
vides EGR without the external hardware as seen on previous systems.
INLET
TURBULENCE
IDLE AIR
CONTROL VALVE
MDK
INT. EGR
CATALYST
CLOSE TO
ENGINE
SECONDARY
AIR
INJECTION
(AIR FILTER)
OUTLET-VANOS
(228/80-105)
INLET-VANOS
(228/80-120)
36
M54engMS43/ST036/6/2000
ELECTRIC FAN
The electric cooling fan is now controlled by the ECM. The ECM uses a remote power out-
put final stage (mounted on the fan housing)
The power output stage receives power from a 50 amp fuse (located in glove box above
the fuse bracket). The electric fan is controlled by a pulse width modulated signal from the
ECM.
The fan is activated based on the ECM calcula-
tion (sensing ratio) of:
Coolant outlet temperature
Calculated (by the ECM) catalyst temperature
Vehicle speed
Battery voltage
Air Conditioning pressure (calculated by IHKA
and sent via the K-Bus to the ECM)
NOTE: If the ECM indicates a fault check the fan for freedom of movement
After the initial test has been performed, the fan is brought up to the specified operating
speed. At 10% (sensing ratio) the fan runs at 1/3 speed. At a sensing ratio of between 90-
95% the fan is running at maximum speed. Below 10% or above 95% the fan is stationary.
The sensing ratio is suppressed by a hysteresis function, this prevents speed fluctuation.
When the A/C is switched on, the electric fan is not immediately activated.
After the engine is switched off, the fan may continue to operate at varying speeds (based
on the ECM calculated catalyst temperature). This will cool the radiator down from a heat
surge (up to 10 minutes).
OUTPUT STAGE
M S 4 2 . 0
POWER
MS 43.0
37
M54engMS43/ST036/6/20000
SECONDARY AIR INJ ECTION
This ECM controlled function remains unchanged from
the previous Siemens MS system, however there is a
hardware change.
The Air Injection Inlet Valve mounts directly to the cylin-
der head, with a passageway machined through the
head. This eliminates the external Air Injection manifold
distribution pipes to the exhaust manifolds.
SECONDARY AIR INJ ECTION MONITORING
In order to reduce HC and CO emissions while the engine is warming up, BMW imple-
mented the use of a Secondary Air Injection System in. Immediately following a cold engine
start (-10 - 40C) fresh air/oxygen is injected directly into the exhaust manifold. By inject-
ing oxygen into the exhaust manifold:
The warm up time of the catalyst is reduced
Oxidation of the hydrocarbons is accelerated
The activation period of the air pump can vary depending on engine type and operating
conditions.
Conditions for Secondary Air Pump Activation:
*NOTE: Below -10C the air injection pump is activated only as a preventive measure to
blow out any accumulated water vapor that could freeze in the system.
REQUIREMENTS STATUS/CONDITION
M52 & M44
STATUS/CONDITION
M73
Oxygen sensor Open Loop Open Loop
Oxygen sensor heating Active Active
Engine coolant temperature -10 to 40C* -10 to 40C* Stage
Engine bad Predefined Range Predefined Range
Engine speed Predefined Range Predefined Range
Fault Codes No Secondary Air Faults
currently present
No Secondary Air Faults
currently present
MS 43.0
38
M54engMS43/ST036/6/2000
The Secondary Air Injection System is monitored via the use of the pre-catalyst oxygen sen-
sor(s). Once the air pump is active and is air injected into the system the signal at the oxy-
gen sensor will reflect a lean condition. If the oxygen sensor signal does not change with-
in a predefined time a fault will be set and identify the faulty bank(s). If after completing the
next cold start and a fault is again present the "Service Engine Soon" light will be illuminat-
ed.
Example: Secondary Air Injection Monitoring (M54-Siemens System)
During a cold start condition air is immediately injected into the exhaust manifold and since
the oxygen sensors are in open loop at this time the voltage at the pre catalyst sensor will
reflect a lean condition) and will remain at this level while the air pump is in operation. Once
the pump is deactivated the voltage will change to a rich condition until the system goes
into closed loop operation.
M54 System Operation:
The pump draws air through its own air filter and delivers it to both exhaust manifolds
through a non-return (shutoff valve). The non-return valve is used to:
1. Control air injection into the exhaust manifold - A vacuum controlled valve will open the
passageway for air to be injected once a vacuum is applied.
2. Prevent possible backfires from traveling up the pipes and damaging the air pump when
no vacuum is applied.
The control module activates the vacuum vent valve whenever the air pump is energized.
Once the vacuum vent valve is energized a vacuum is applied to the non-return valve which
allows air to be injected into the exhaust manifold. A vacuum is retained in the lines, by the
use of a check valve, in order to allow the non-return valve to be immediately activated on
cold engine start up. When the vacuum/vent valve is not energized, the vacuum to the
non-return valve is removed and is vented to atmosphere.
39
M54engMS43/ST036/6/20000
ENGINE/VEHICLE SPEED
LIMITATION
For engine/vehicle speed limitation, the ECM will deactivate injection for individual cylinders,
allowing a smoother limitation transition. This prevents over-rev when the engine reaches
maximum RPM (under acceleration), and limits top vehicle speed (approx. 128 mph).
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
MS 43.0
DSC
40
M54engMS43/ST036/6/2000
RZV IGNITION SYSTEM
The Siemens MS43.0 system uses a multiple spark ignition function. The purpose of mul-
tiple ignition is:
Provide clean burning during engine start up and while idling (reducing emissions).
This function helps to keep the spark plugs clean for longer service life (new BMW
longlife plugs).
Multiple ignition is active up to an engine speed of approximately 1350 RPM (varied with
engine temperature) and up to 20 degrees after TDC.
Multiple ignition is dependent on battery voltage. When the voltage is low, the primary cur-
rent is also lower and a longer period of time is required to build up the magnetic field in the
coil(s).
Low battery voltage = less multiple ignitions
High battery voltage = more multiple ignitions
The 240 ohm shunt resistor is still used on the MS43.0 system for detecting secondary igni-
tion faults and diagnostic purposes.
MS 43.0
41
M54engMS43/ST036/6/20000
RESONANCE/TURBULENCE INTAKE SYSTEM
On the M54, the intake manifold is split into 2 groups of 3 (runners) which increases low
end torque. The intake manifold also has separate (internal) turbulence bores which chan-
nels air from the idle speed actuator directly to one intake valve of each cylinder (matching
bore of 5.5mm in the cylinder head).
Routing the intake air to only one intake valve causes the intake to swirl in the cylinder.
Together with the high flow rate of the intake air due to the small intake cross sections, this
results in a reduction in fluctuations and more stable combustion.
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
M D K
H F M
MAGNETIC
VALVE
VACUUM
UNIT
M S 4 2 . 0
RAM TUBE
MAIN MAINIFOLD
RESONANCE TUBE
IDLE AIR CONTROL VALVE
(ZWD)
RESONANCE MANIFOLD
CRANKCASE VENTILATION
TURBULENCE MANIFOLD
TURBULENCE BORE 0:5.5mm
MS 43.0
EDK
42
M54engMS43/ST036/6/2000
RESONANCE SYSTEM
The resonance system provides increased engine torque at low RPM, as well as addition-
al power at high RPM. Both of these features are obtained by using a resonance flap (in
the intake manifold) controlled by the ECM.
During the low to mid range rpm, the resonance flap is closed. This produces a long/sin-
gle intake tube for velocity, which increases engine torque.
During mid range to high rpm, the resonance flap is open. This allows the intake air to pull
through both resonance tubes, providing the air volume necessary for additional power at
the upper RPM range.
When the flap is closed , this creates another dynamic effect. For example, as the intake
air is flowing into cylinder #1, the intake valves will close. This creates a roadblock for the
in rushing air. The air flow will stop and expand back (resonance wave back pulse) with the
in rushing air to cylinder #5. The resonance wave, along with the intake velocity,
enhances cylinder filling.
The ECM controls a solenoid valve for resonance flap activation. At speeds below 3750
RPM, the solenoid valve is energized and vacuum supplied from an accumulator closes
the resonance flap. This channels the intake air through one resonance tube, but increas-
es the intake velocity.
When the engine speed is greater than 4100 RPM (which varies slightly - temperature influ-
enced), the solenoid is de-energized. The resonance flap is sprung open, allowing flow
through both resonance tubes, increasing volume.
43
M54engMS43/ST036/6/20000
#1 Cylinder Intake Valve open
Low to Mid Range RPM
(<3750 RPM)
MS 43.0
#1 Cylinder Intake Valve closes
#5 Intake Valve Opens
=> Intake Air Bounce Effect
Low to Mid Range RPM
(<3750 RPM)
MS 43.0
EDK
EDK
44
M54engMS43/ST036/6/2000
#1 Cylinder Intake Valve open -
Intake air drawn from both
resonance tubes.
Mid to High Range RPM
(>3750 RPM)
#5 Cylinder Intake Valve open -
Intake air drawn from both
resonance tubes.
Mid to High Range RPM
(>3750 RPM)
MS 43.0
MS 43.0
EDK
EDK
45
M54engMS43/ST036/6/20000
IDLE SPEED CONTROL
The ECM determines idle speed by controlling an idle speed actuator (dual winding rotary
actuator) ZWD 5.
The basic functions of the idle speed control are:
Control the initial air quantity
(at air temperatures <0 C,
the EDK is simultaneously
opened)
Variable preset idle based on
load and inputs
Monitor RPM feedback for
each preset position
Lower RPM range intake air
flow (even while driving)
Vacuum limitation
Smooth out the transition from acceleration to deceleration
Under certain engine operating parameters, the EDK throttle control and the idle speed
actuator (ZWD) are operated simultaneously.This includes All idling conditions and the tran-
sition from off idle to load.
As the request for load increases, the idle valve will remain open and the EDK will supply
any additional air volume required to meet the demand.
Emergency Operation of Idle Speed Actuator:
If a fault is detected with the idle speed actuator, the ECM will initiate failsafe measures
depending on the effect of the fault (increased air flow or decreased air flow).
If there is a fault in the idle speed actuator/circuit, the EDK will compensate to maintain idle
speed. The EML lamp will be illuminated to inform the driver of a fault.
If the fault causes increased air flow (actuator failed open), VANOS and Knock Control are
deactivated which noticeably reduces engine performance.
M D K
H F M
MAGNETIC
VALVE
VACUUM
UNIT
M S 4 2 . 0
RAM TUBE
MAIN MAINIFOLD
RESONANCE TUBE
IDLE AIR CONTROL VALVE
(ZWD)
RESONANCE MANIFOLD
CRANKCASE VENTILATION
TURBULENCE MANIFOLD
TURBULENCE BORE 0:5.5mm
MS 43.0
EDK
46
M54engMS43/ST036/6/2000
CRUISE CONTROL
Cruise control is integrated into the ECM because of the EDK operation.
Cruise control functions are activated directly by the multifunction steering wheel to the
ECM. The individual buttons are digitally encoded in the MFL switch and is input to the ECM
over a serial data wire.
The ECM controls vehicle speed by activation of the Electronic Throttle Valve (EDK)
The clutch switch disengages cruise control to prevent over-rev during gear changes.
The brake light switch and the brake light test switch are input to the ECM to disengage
cruise control as well as fault recognition during engine operation of the EDK.
Road speed is input to the ECM for cruise control as well as DSC regulation. The vehicle
speed signal for normal engine operation is supplied from the DSC module (right rear wheel
speed sensor). The road speed signal for cruise control is supplied from the DSC module.
This is an average taken from both front wheel speed sensors, supplied via the CAN bus.
DSC
MS 43.0
EDK
47
M54engMS43/ST036/6/20000
PURGE VALVE
The purge valve (TEV) is activated at 10 Hz by the ECM to cycle open, and is sprung
closed. The valve is identical to the purge valve used on the Siemens MS 42 system.
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
48
M54engMS43/ST036/6/2000
REVIEW QUESTIONS
1. List the major changes to the Siemens MS 43.3 system from MS 42:
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
2. What type of signal does the Hall Sensor - PWG provide to ECM for throttle request?
_____________________________________________________________________________
3. What PWG signal is used if PWG has a plausibility error?
_____________________________________________________________________________
4. What is the purpose of the KL 87 main relay monitor in the ECM?
_____________________________________________________________________________
5. Why is the ignition left ON after KL 15 is switched OFF?
_____________________________________________________________________________
6. Describe the operation of the DM-TL system on MS 43.0.
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
7. Describe the operation of the turbulence - resonance manifold.
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________