ECN3021
ECN3021
ECN3021
HIGH-VOLTAGE MONOLITHIC IC
ECN3021
ECN3021 is a single chip three-phase bridge inverter IC which has 6 IGBTs in the circuit.
Especially, it is very suitable for controlling the speed of 3-phase DC brushless motors to which
converted AC200~230V power supplies are applied. Fig. 1 shows the internal block diagram.
Functions
Integrated charge pump circuit
Integrated free wheel diodes
Integrated PWM circuit
Integrated FG circuit
Integrated over current protection circuit
Integrated rotating direction monitor circuit
Features
Speed control for a 3-phase DC brushless motor is available with an external microprocessor.
Bottom arm circuits can be operated in 20kHz chopping frequency of PWM.
Clock
GH1
Charge Pump
Bottom Arm
Driver
Top Arm
Driver
VS1 VS2
MU
MV
MW
CL
GL
VS
Clock
SAW wave
Generator
VTR
D2
D1
C1
C2
+
+
-
-
3-Phase
VB supply
RTR
CTR
+
-
Over Current Sense
HU HW HV
CR
Vref
+
-
RS
RS
0.5V
RU
RV
RW
Distributor
Comparator
Motor
Hall ICs
Microprocessor
CMP
VSP
VCC VB
CB
C0
VCC(15V)
C+ C-
GH2
Analog
output
FG
FG
DM Rotating
Direction
Monitor
Fig. 1 Block diagram
PDE-3021-0
ECN3021
1. General
(1) Type ECN3021
(2) Application 3-phase DC Brushless Motor
(3) Structure Monolithic IC
(4) Package SP-23T
2. Maximum Allowable Ratings (Ta=25C)
No. Items Symbols Terminal Ratings Unit Condition
1 Output Device
Breakdown Voltage
VSM VS1,VS2
MU,MV,MW
500 V
2 Supply Voltage VCC VCC 18 V
3 Input Voltage VIN VSP,RS
HU,HV,HW
-0.5 ~ VB+0.5
V
4 Output Current IMDC MU,MV,MW 0.7 A
5 Peak Output Current IMP MU,MV,MW 1.0 A Note 1
6 Output Current in Start
Up and Accelerating
IOM MU,MV,MW 1.0 A Note 1
7 Operating Junction
Temperature
Tjop
-20 ~ +135
C Note 2
8 Storage Temperature Tstg
-40 ~ +150
C
Note 1. Please note that acumulated duty of a period exceeding 0.7A has to be less than 5% of total current
flowing period.
Note 2. Thermal Resistance
Rj-c = 4C/W
Rj-a = 40C/W
3. Recommended Operating Conditions
No. Items Symbols Terminal MIN TYP MAX Unit Condition
1 Supply Voltage VS VS1,2 50 325 370 V
2 VCC VCC 13.5 15 16.5 V
Note. Recommended Safe Operating Area(SOA)
It is recommended that this IC should be used within the SOA as shown below, where IM and VM are
the current and the voltage at the terminals connected to motor coils when the phase is changed (turned
off).
0 370
VM (V)
IM
(A)
1.0
0
Safe
Operating Area
PDE-3021-0
ECN3021
4. Electrical Characteristics (Ta=25C)
Unless otherwise specified, VCC=15V, VS=325V Suffix T; Top arm B; Bottom arm
No. Items Symbols Terminal MIN TYP MAX Unit Condition
1 Standby Current IS VS1,2 - 2.5 5.0 mA VSP=0V
2 ICC VCC - 10 20 mA
3 Output device FVD VFT MU,MV,MW - 4.0 6.0 V I=0.35A
4 VFB MU,MV,MW - 4.0 6.0 V I=0.35A
5 Turn On TdONT MU,MV,MW - 0.5 3.0 s
6 Delay Time TdONB MU,MV,MW - 0.5 3.0 s I=0.35A
7 Turn Off TdOFFT MU,MV,MW - 3.0 6.0 s Resistance Load
8 Delay Time TdOFFB MU,MV,MW - 1.0 3.0 s
9 Free Wheel VFDT MU,MV,MW - 4.0 6.0 V I=0.35A
10 Diode FVD VFDB MU,MV,MW - 4.0 6.0 V
11 Output Resistance RVTR VTR - 200 400
12 H or L Level of VSAWH CR 4.9 5.4 6.1 V Note 2
13 SAW wave VSAWL CR 1.7 2.1 2.5 V
14 Amplitude of
SAW wave
VSAWW CR 2.8 3.3 3.8 V Note 3
15 Reference Voltage Vref RS 0.45 0.5 0.55 V
16 Hall signal VIH HU,HV,HW 3.5 - - V
17 Input Voltage VIL HU,HV,HW - - 1.5 V
18 Hall signal
Input Current
IIL HU,HV,HW -100 - - A HU,HV,HW=0V
Note 1
Pull Up Resistance
19 VSP Input Current IVSPH VSP - - 100 A VSP=5.0V Note 1
Pull Down Resistance
20 VB Output Voltage VB CB 6.8 7.5 8.2 V
21 VB Output Current IB CB 25 - - mA delta Vload=0.1V
22 FG,DM
Output Voltage
VOL FG,DM - 1.0 - V IOL=-5mA Note 4
23 FG,DM
Output Resistance
ROL FG,DM - 200 400
24 LVSD Output Voltage LVSDON Vcc,MU, 10.0 11.5 12.9 V Note.5
25 LVSD recover Voltage LVSDOFF MV,MW 10.1 12.0 13.0 V
26 LVSD reset hysterisis Vrh 0.1 0.5 0.9 V
Note 1. Pull Up Resistance and Pull Down Resistance are typically 200 k.
Note 2. Please see Note 2 in item 6 for determining the frequency of SAW wave.
Note 3. The amplitude of SAW(VSAWW) is determined by the following equation,
VSAWW=VSAWH-VSAWL (V)
Note 4. The equivalent circuit around FG and DM terminal is shown in Fig. 2
Note 5. LVSD: Low Voltage Shut Down
FG or DM
VCC
Fig.2 Equivalent circuit around FG or DM
PDE-3021-0
ECN3021
5. Function
5.1 Truth Table
Input MU MV MW
HU HV HW Top Bottom Top Bottom Top Bottom
H L H OFF ON ON OFF OFF OFF
H L L OFF ON OFF OFF ON OFF
H H L OFF OFF OFF ON ON OFF
L H L ON OFF OFF ON OFF OFF
L H H ON OFF OFF OFF OFF ON
L L H OFF OFF ON OFF OFF ON
L L L OFF OFF OFF OFF OFF OFF
H H H OFF OFF OFF OFF OFF OFF
5.2 Timing Chart
HU
HV
HW
MU Output
Input
MV Output
MW Output
FG Output
PDE-3021-0
ECN3021
5.3 PWM Operation
The PWM signal is produced by comparing the input voltage at VSP terminal with the voltage from the
internal SAW wave. The duty of the PWM signal can be changed by the triangular wave amplitude level,
from the minimum point of VSAWL to the maximum point of VSAWH, and when the level is under
VSAWL, the duty becomes 0%, and when the level is over VSAWH, the duty becomes 100%. In addition,
chopping with the PWM signal is operated in the bottom arm circuit.
5.4 Over Current Limiting Operation
This IC detects over current by checking the voltage drop at the external resistance RS. When the input
voltage at RS terminal exceeds the internal reference voltage(Vref), this IC turns off the output of the bottom
arm circuit. After over current detection, reset operation is done at every period of the inner clock signal
(VTR terminal).
5.5 Rotating Direction Sense Operation
The rotation direction of the motor is detected by the signal at DM terminal. Table 1 shows the output signal
for the rotation direction.
Table 1. Output signal for the rotation direction
Rotating Direction Output (DM terminal)
U-V-W L
U-W-V H
5.6 Vcc under voltrage Detection
When Vcc supply voltage becomes below LVSDON(11.5V typ), all of the IGBTs shut off.
This condition is recovered when Vcc supply voltage becomes greater than LVSDOFF(12.0V typ).
PDE-3021-0
ECN3021
6. Standard Application
Component Recommended Value Usage Remark
C0 More than 0.22 F for inner power
supply(VB).
stress voltage is VB
C1,C2 0.5 F 20% for charge pump stress voltage is VCC
D1,D2 Hitachi DFG1C6(glass mold)
Hitachi DFM1F6(resin mold)
or equivalent parts
for charge pump 600V/1.0A
trr100ns
Rs Note 1. for current limiting
CTR 1800 pF 5% for PWM Note 2.
RTR 22 k 5% for PWM Note 2.
Note 1. Start up current is limited by the following equation.
IO = Vref / Rs (A)
Note 2. PWM frequency is approximately determined by the following equation.
fPWM = -1 / (2C*R*Ln(1-3.5/5.5)) ; Ln is natural logarithm
= 0.494 / (C*R) (Hz)
Note 3. It is recommended that RU,RV,RW should be 5.6 k 5%.
Clock
GH1
Charge Pump
Bottom Arm
Driver
Top Arm
Driver
VS1 VS2
MU
MV
MW
CL
GL
VS
Clock
SAW wave
Generator
VTR
D2
D1
C1
C2
+
+
-
-
3-Phase
VB supply
RTR
CTR
+
-
Over Current Sense
HU HW HV
CR
Vref
+
-
RS
RS
0.5V
RU
RV
RW
Distributor
Comparator
Motor
Hall ICs
Microprocessor
CMP
VSP
VCC VB
CB
C0
VCC(15V)
C+ C-
GH2
Analog
output
FG
FG
DM Rotating
Direction
Monitor
Fig 3. Block diagram and external elements
PDE-3021-0
ECN3021
7. Terminal
(Marking side)
Fig.4 Pin Connection
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
MV
VS1
MU
GH1
RS
HU
HW
VTR
CR
CB
C+
CL
GL
MW
VS2
GH2
VCC
C-
VSP
HV
FG
DM
8. Package Outline
ECN3021SP ECN3021SPV ECN3021SPR
PDE-3021-0
ECN3021
8. Package Dimensions
(1) ECN3021SP
(2) ECN3021SPV
PDE-3021-0
ECN3021
(3) ECN3021SPR
0.3
23.97
0.6
1.8 typ
0.1
1
1
.
2
1
4
.
7
M
A
X
1.23
0.25
3
.
6
4.1
0.3
(
7
.
7
)
(
9
)
1.27
0.5
2.54
0.5
2.54
0.5
1.26
0.24
3.5
0
.
2
5
t
y
p
4
.
9
0
.
5
0
.
3
0
.
2
2
.
2
0
.
3
1
2
.
3
0
.
5
7
.
1
0
.
5
0
+
1
0
+
1
0
3.6
0.3
0.2
0.2
0.5
0.2
20
28
0.3
(30)
31MAX
1 23
1. The information given herein, including the specifications and dimensions, is subject to
change without prior notice to improve product characteristics. Before ordering,
purchasers are advised to contact Hitachi sales department for the latest version of this
data sheets.
2. Please be sure to read "Precautions for Safe Use and Notices" in the individual
brochure before use.
3. In cases where extremely high reliability is required (such as use in nuclear power
control, aerospace and aviation, traffic equipment, life-support-related medical
equipment, fuel control equipment and various kinds of safety equipment), safety should
be ensured by using semiconductor devices that feature assured safety or by means of
users fail-safe precautions or other arrangement. Or consult Hitachis sales department
staff.
4. In no event shall Hitachi be liable for any damages that may result from an accident or
any other cause during operation of the users units according to this data sheets.
Hitachi assumes no responsibility for any intellectual property claims or any other
problems that may result from applications of information, products or circuits described
in this data sheets.
5. In no event shall Hitachi be liable for any failure in a semiconductor device or any
secondary damage resulting from use at a value exceeding the absolute maximum
rating.
6. No license is granted by this data sheets under any patents or other rights of any third
party or Hitachi, Ltd.
7. This data sheets may not be reproduced or duplicated, in any form, in whole or in part ,
without the expressed written permission of Hitachi, Ltd.
8. The products (technologies) described in this data sheets are not to be provided to any
party whose purpose in their application will hinder maintenance of international peace
and safety not are they to be applied to that purpose by their direct purchasers or any
third party. When exporting these products (technologies), the necessary procedures
are to be taken in accordance with related laws and regulations.
For inquiries relating to the products, please contact nearest overseas representatives which is located
Inquiry portion on the top page of a home page.
HITACHI POWER SEMICONDUCTORS
Notices
Hitachi power semiconductor home page address http://www.pi.hitachi.co.jp/pse