Page 1

ZFSM- 201-1
ZFSM- 201-2
FREESTAR PRO SERIES TRANSCEIVER MODULES
DESCRIPTION
CELs FreeStar Pro module provides a high performance and cost
effective RF transceiver solution for 2.4 GHz IEEE 802.15.4, ZigBee,
and Zigbee PRO wireless networks.

The FreeStar Pro module is based on the Freescale MC13224V
(ZFSM-201-1) or MC13226V (ZFSM-201-2) transceiver platforms. It
combines Freescales transceiver IC with an onboard 100mW Power
Amplifer. Ideal for remote sensing, AMR/AMI, home and building
automation, industrial control, and security applications, FreeStar Pro
combines extensive processing capability with high output power and
low power consumption.

The processing power of the MC1322xV enables the FreeStar Pro to
provide a level of integration unprecedented in a ZigBee module. The
32-bit ARM7TDMI processor and expansive on-chip memory enable
designers to eliminate the peripheral host processors often required
by 8- and 16-bit transceiver solutions. This high level of integration
reduces component count, lower power consumption and overall
system costs.
Integrated Transceiver Modules for ZigBee / IEEE 802.15.4
Evaluation Kit available: ZFSM-201-KIT-1
The information in this document is subject to change without notice, please confrm data is current
Document No: 0006-00-07-00-000 (Issue A)
Date Published: December 10, 2010
DATA SHEET
Transmit Power: 100 mW
Receive Sensitivity: -94 dBm
Freescale MC1322xV platform
128 kB Serial Flash Memory
96 kB SRAM
80 kB ROM
32-bit ARM7TDMI-based MCU
46 GPIO Pins
12-bit ADC
FREESTAR PRO
ZFSM-201-x
APPLICATIONS
Powerful 32-bit ARM7TDMI based microprocessor
Extensive on-board memory resources
Up to 100 mW output power
Miniature footprint: 1 x 1.4 (25.4 mm x 36.5 mm)
Integrated PCB trace antenna
15 RF channels
Over 4000 feet of range
AES 128-bit encryption
Low power consumption
FCC, CE and IC certifed
RoHS compliant
ORDERING INFORMATION
Part Number Order Number Description
ZFSM-201-1
MC13224V
ZFSM-201-1 100 mW Output power, PCB Trace Antenna Intended for 802.15.4 Standard com-
pliant applications,Freescale 802.15.4
MAC, and Freescale BeeStack.
ZFSM-201-1C 100 mW Output power, MMCX connector for external antenna
ZFSM-201-2
MC13226V
ZFSM-201-2 100 mW Output power, PCB Trace Antenna
Intended specifcally for Freescale
BeeStack Pro applications.
ZFSM-201-2C 100 mW Output power, MMCX connector for external antenna
FREESTAR PRO
Development Kit
ZFSM-201-KIT-1 Engineering Evaluation Kit
FEATURES
Home &
Building Automation
Security
HVAC control
Lighting control
Thermostats
Industrial Controls
Food processing controls
Traffc Management
Sensor Networks
Asset Management
Barcode reader
Patient Monitoring
Glucose monitor
Automated Meter
Reading
In meter applications
Thermostats
In-home display units
ZFSM-201 Series
Page 2
FREESTAR PRO MODULE BLOCK DIAGRAM
EVALUATION KIT
The FreeStar Pro Kits assists users in both evaluation and
development. As a stand alone radio system, the kit allows users
to place the modules into the target environment and evaluate
performance. The FreeStar Pro kit also serves as an invaluable
aid in application development. Through the many headers on
the interface board, the user has access to all pins on the
ZFSM-201-1 enabling easy connection to the target system for
application development.
The FreeStar Pro module contains the Freescale MC1322xV
transceiver IC, an NEC high gain Power Amplifer, XTALs, Power
Regulator, and an integrated PCB antenna.

The interface board features a serial communication interface, a
power management module, peripherals such as potentiometer
LEDs, and GPIO headers. The Evaluation Kit also contains four
AA batteries and two USB cables.
For more detailed information regarding FreeStar Pro Evaluation
Kit, refer to the FreeStar Pro Evaluation Kit User Guide document.
(Available at CELs website http://www.cel.com)
Kit Contents:
32.768 kHz XTAL (optional)
32.768 kHz XTAL
C
a
s
t
e
l
l
a
t
i
o
n

E
d
g
e
C
o
n
n
e
c
t
o
r
24 MHz
XTAL
PWR
Reg
Radio
ANT
Micro
processor
Freescale
MC1322xV
RF Front End
(NEC PA and
NEC Switch)
FreeStar Pro
Three Evaluation Boards with ZFSM-201-1 Modules
Two USB A/B Cables
Ten Jumpers (Spares)
Four AA Batteries
Software & Technical Information CD
ZFSM-201 Series
Page 3
Introduction and Overview
Description.............................................................................................................................................................................................. 1
Features.................................................................................................................................................................................................. 1
Applications............................................................................................................................................................................................ 1
Ordering Information............................................................................................................................................................................. 1
Module Block Diagram........................................................................................................................................................................... 2
Evaluation Kit......................................................................................................................................................................................... 2
System Level Function
Module Microprocessor......................................................................................................................................................................... 4
Modes of Operation (TX, RX, Sleep)...................................................................................................................................................... 5
Power Amplifer....................................................................................................................................................................................... 6
Power Amplifer Control Line................................................................................................................................................................. 6
Interface.................................................................................................................................................................................................. 6
Host Protocol Interface Commands...................................................................................................................................................... 6
Electrical Specifcation
Absolute Maximum Ratings................................................................................................................................................................... 7
Recommended (Operating Conditions)................................................................................................................................................ 7
DC Characteristics.................................................................................................................................................................................. 7
RF Characteristics.................................................................................................................................................................................. 7
Pin Signal & Interfaces
Pin Signals I/O Confguration................................................................................................................................................................ 8
I/O Pin Assignments............................................................................................................................................................................... 9
Module Dimensions................................................................................................................................................................................ 11
Processing
13
Agency Certifcations
14
Shipment, Storage & Handling
16
References & Revision History
17
TABLE OF CONTENTS
ZFSM-201 Series
Page 4
MICROPROCESSOR
The primary component of the FreeStar Pro module is Freescales third generation ZigBee platform. It incorporates a
complete, low power, 2.4 GHz radio frequency transceiver, 32-bit ARM7TDMI-based microprocessor, hardware acceleration
for both IEEE 802.15.4 MAC and AES security plus a full suite of processor peripherals.
The MC1322xV architecture offers superior processing power for ZigBee applications. The core operates up to 26 MHz.
An 80 kByte ROM is utilized for the low level IEEE 802.15.4 MAC and PHYsical layer commands. This off loads the Flash
memory, leaving more space for the end user application. The MC1322xV supports 128 kBytes of Flash memory. The
program code is mirrored in 96 kBytes of RAM for faster execution by the processor core. A full set of peripherals and Direct
Memory Access (DMA) capability for transceiver packet data are also included.
In addition, the MC1322xV provides extensive power savings options, including low current sleep modes allowing for
maximum operating life when battery-powered.
The MC1322x family is available as two part numbers. These device types differ only in their ROM contents, all other
device hardware, performance, and specifcations are identical:

MC13224V - this is the original version and is the generic part type.
- The MC13224V is intended for most IEEE 802.15.4 applications including MAC-based,
ZigBee-2007 Profle 1, and ZigBee RF4CE targets.
- It has a more complete set of peripheral drivers in ROM.
MC13226V - this is a more recent version and is provided specifcally for ZigBee-2007 Profle 2 (Pro)
applications. Only the onboard ROM image has been changed to optimize ROM usage for the ZigBee Pro profle
and maximize the amount of available RAM for application use.
- The IEEE MAC/PHY functionality has been streamlined to include only that functionality
required by the ZigBee specifcation. The MAC functionality is 802.15.4 compatible.
- For a typical application, up to 20 kbytes more of RAM is available versus the M13224V
- Some drivers present in the MC13224 ROM have been removed and these include the ADC,
LCD font, and SSI drivers. These drivers are still available as library functions, but now compile into the
RAM space.
- The Low Level Component (LLC) functionality has also been streamlined for the ZigBee Specifcation.
ANTENNA
FreeStar Pro modules include an integrated PCB trace antenna. An optional MMCX connector can be specifed, enabling
connection to a 50-ohm external antenna of the users choice. See Ordering Information on page 1.
The PCB antenna employs an F-Antenna topology that is compact and supports an omni-directional radiation pattern.
To maximize antenna effciency, an adequate ground plane must be provided on the host PCB. Correctly positioned, the
ground plane on the host board under the module will contribute signifcantly to antenna performance.
The position of the module on the host board and overall design of the product enclosure contribute to antenna perfor-
mance. Poor design affects radiation patterns and can result in refection, diffraction, and/or scattering of the transmitted
signal.
Here are some design guidelines to help ensure antenna performance:
Never place the ground plane or route copper traces directly underneath the antenna portion of the module.
Never place the antenna close to metallic objects.
In the overall design, ensure that wiring and other components are not placed near the antenna.
Do not place the antenna in a metallic or metallized plastic enclosure.
Keep plastic enclosures 1cm or more from the antenna in any direction.
ZFSM-201 Series
Page 5
MODES OF OPERATION
FreeStar Pro power management is controlled through the Freescale MC1322xVs Clock and Reset Module (CRM). The
CRM is a dedicated module to handle clock, reset, and power management functions including control of the power regula-
tors. All these functions have direct impact on attaining the lowest power.
The FreeStar Pro module supports three modes of operation: Active, Doze and Hibernation. The latter two modes are the
low-power sleep modes.

Active Mode
In this mode all functions / features are operating normally.
Doze Mode
Doze mode provides signifcant reduction in power consumption while still maintaining a high degree of sleep timing accu-
racy. In Doze mode, the reference oscillator of the processor continues to operate normally.
Hibernation Mode
Hibernation mode provides the greatest reduction in power consumption however the sleep timing accuracy is not as pre-
cise as in Doze mode.
The CRM manages the recovery from the low-power modes, similar to power-up from reset, providing regulator and clock
management.

The module can be awoken from the low-power modes in 3 ways, wake-up can occur:
On external interrupts through any of the 4 Keyboard Interface inputs
From internal interrupts
On the Real Time (wake-up) timer interrupt

For more detail information on modes of operation refer to Freescales MC1322xV datasheet available at
Freescales website (www.freescale.com)
ZFSM-201 Series
Page 6
POWER AMPLIFIER
The FreeStar Pro module incorporates a high performance Power Amplifer from NEC Electronics.
Power Amplifer Control Line
FreeStar Pro modules include a separate 1.8V regulator supplying a bias that enables consistent module output performance
over the wide operating range. To prevent excessive sleep current draw, this regulator should be disabled when the module is
placed into sleep mode.The voltage regulator is controlled by GPIO42 (ANT1), setting GPIO42 high enables the regulator while
setting GPIO42 low disables the regulator. See the table below for the Turn on Time requirements for the voltage regulator.
SPECIFICATIONS GPIO42
Parameter Min Typ Max Unit
Regulator enable voltage 0.95 V
Regulator disable voltage 0.40 V
Turn on Time for VOUT=1.8V (Default) 105 200 sec
For the TX_ON and RX_ON pins, the function table is as follows:
Parameter TX Mode RX Mode
TX_ON High Low
RX_ON Low High
Other Notes:
The GPIO43 (ANT2) pin is not used and is left unconnected.
Due to the long turn on time (105s) of the regulator, the regulator is enabled or ON all the time with the
execption of sleep mode.
The RF switch uses both the TX_ON and RX_ON outputs as control inputs.
The PA uses the TX_ON line as the control input.


RF Output Power Setting
In order to comply with FCC emissions requirements, the FreeStar PRO module must operate at reduced power settings
on channels 11 & 12. Channel 26 is unavailable. The frmware provided with the modules also limits the users to Test Tool
power step 2 for channels 11 & 12. This is to guarantee the module does not exceed 10dBm which is required to meet the
FCC requirements of this module.
In addition to restricting power, the frmware also limits the maximum data payload to 106 bytes for any transmitted packet.
This is to guarantee the module does not exceed 10dBm on channels 11 & 12 which is necessary to meet FCC emissions
requirements.
INTERFACE
The FreeStar Pro module has all major pins routed to the castellation connectors, this includes, but is not limited, to the pins for
JTAG, serial communication, A/D, etc.
ZFSM-201 Series
Page 7

HOST PROTOCOL INTERFACE COMMANDS
CEL provides the Host Serial and RF Protocols document which details the protocols and commands between the Host
processor (i.e. an external microprocessor, a PC, etc.) and the FreeStar Pro module. An example of the commands, but
not limited to, included in the host protocol interface are as follows:
Query Version (MAC version)
Set RF Channel
Set RF Power
Transmit Packet Error Test
For more detail refer to Host Serial and RF Protocols document listed on our website at http://www.cel.com
(FreeStar Pro Host & RF Protocol)
ABSOLUTE MAXIMUM RATINGS
Description Min Max Unit
Power Supply Voltage -0.3 3.6 VDC
Voltage on Any Digital Pin -0.3 VCC + 0.2 VDC
RF Input Power 10 dBm
Storage Temperature Range -45 125 C
Refow Soldering Temperature 260 C
Note: Exceeding the maximum ratings may cause permanent damage to the module.
RECOMMENDED OPERATING CONDITIONS
Description Min Typ Max Unit
Power Supply Voltage (VCC) 2.1 3.6 VDC
Ambient Temperature Range -40 25 85 C
Crystal Reference Oscillator 24 MHz

DC CHARACTERISTICS (@ 25C, VCC = 3.3V unless otherwise noted)
Description Typ Max Unit
Transmit Mode Current
(at +20 dBm Output Power)
193 mA
Receive Mode Current 30 mA
Hibernate or Doze Mode Current 5 A
ZFSM-201 Series
Page 8

RF CHARACTERISTICS (@ 25C, VCC = 3.3V unless otherwise noted)
Parameter Min Typ Max Unit
General Charcteristics
RF Frequency Range 2400 2483.5 MHz
RF Data Rate 250 kbps
Transmitter
Nominal Output Power 20 dBm
Programmable Output Power Range 18 dB
Error Vector Magnitude 8 35 %
Receiver
Receiver Sensitivity (1% PER) -92 -94 dBm
Saturation (Maximum Input Level) (1% PER) 0 dBm
802.15.4 Adjacent Channel Rejection (5 MHz) 35 40 dB
802.15.4 Alternate Channel Rejection (10 MHz) 50 dB
PIN SIGNALS I/O PORT CONFIGURATION
The FreeStar Pro module has 60 edge I/O interfaces for connection to the users host board. Figure 1 shows the layout of
the 60 edge castellations.
ZFSM-201 Series
Page 9
FREESTAR PRO I/O PIN ASSIGNMENTS
Pin # Name Type Description
IC
Pin #
1 GND GND GND 85
2 GND GND GND 84
3 GND GND GND 75
4 ADC2_VREFL
Analog Input or
Digital I/O
GPIO39
Alternate function: Low reference voltage for ADC2
61
5 ADC1_VREFL
Analog Input or
Digital I/O
GPIO41
Alternate function: Low reference voltage for ADC1
62
6 ADC1_VREFH
Analog Input or
Digital I/O
GPIO40
Alternate function: High reference voltage for ADC1
63
7 ADC2_VREFH
Analog Input or
Digital I/O
GPIO38
Alternate function: Low reference voltage for ADC2
64
8 ADC0
Analog Input or
Digital I/O
GPIO30
Alternate function: ADC analog input Channel 0
1
9 ADC1
Analog Input or
Digital I/O
GPIO31
Alternate function: ADC analog input Channel 1
2
10 ADC2
Analog Input or
Digital I/O
GPIO32
Alternate function: ADC analog input Channel 2
3
11 ADC3
Analog Input or
Digital I/O
GPIO33
Alternate function: ADC analog input Channel 3
4
12 VCC Power Input
High side supply voltage to buck regulator switching MOSFET & IO
buffers
45
13 ADC4
Analog Input or
Digital I/O
GPIO34
Alternate function: ADC analog input Channel 4
5
14 ADC5
Analog Input or
Digital I/O
GPI035
Alternate function: ADC analog input Channel 5
6
15 ADC6
Analog Input or
Digital I/O
GPIO036
Alternate function: ADC analog input Channel 6
7
16 ADC7_RTCK
Analog Input or
Digital I/O
GPI037
Alternate function: ADC analog input Channel 7 / Return ClocK
8
17 TDO Digital I/O
GPI049
Alternate function: JTAG Test Data Output
9
18 TDI Digital I/O
GPI048
Alternate function: JTAG Test Data Input
10
19 TCK Digital I/O
GPIO47
Alternate function: JTAG Test Clock Input
11
20 TMS Digital I/O
GPIO46
Alternate function: JTAG Test Mode Select Input
12
21 UART2_RTS Digital I/O
GPIO21
Alternate function: UART2 Request to Send input
13
22 GND GND GND 76
23 UART2_CTS Digital I/O
GPI020
Alternate function: UART2 Clear to Send output
14
24 UART2_RX Digital I/O
GPIO19
Alternate function: UART2 RX data input
15
25 UART2_TX Digital I/O
GPIO18
Alternate function: GPIO18UART2 TX data output
16
26 UART1_RTS Digital I/O
GPI017
Alternate function: UART1 Request to Send input
17
27 UART1_CTS Digital I/O
GIO016
Alternate function: UART1 Clear to Send output
18
28 I2C_SDA Digital I/O
GPIO13
Alternate function: I2C Bus data
21
29 I2C_SCL Digital I/O
GPIO12
Alternate function: I2C Bus clock
22
30 TMR3 Digital I/O
GPIO11
Alternate function: Timer 3 IO signal
23
ZFSM-201 Series
Page 10
FREESTAR PRO I/O PIN ASSIGNMENTS (Continued)
Pin # Name Type Description
IC
Pin #
31 VCC Power Input High side supply voltage to buck regulator switching MOSFET & IO buffers 45
32 TMR2 Digital I/O
GPIO10
Alternate function: Timer 2 IO signal
24
33 TMR1 Digital I/O
GPIO9
Alternate function: Timer 1 IO signal
25
34 TMR0 Digital I/O
GPIO8
Alternate function: Timer 0 IO signal
26
35 SPI_SCK Digital I/O
GPIO7
Alternate function: SPI Port clock
27
36 UART1_TX Digital I/O
GPIO14
Alternate function: UART1 TX data output
20
37 UART1_RX Digital I/O
GPIO15
Alternate function: UART1 RX data input
19
38 GND GND GND 77
39 SPI_MOSI Digital I/O
GPIO6
Alternate function: SPI Port MOSI
28
40 SPI_MISO Digital I/O
GPIO5
Alternate function: SPI Port MISO
29
41 SPI_SS Digital I/O
GPIO4
Alternate function: SPI Port SS
30
42 SSI_BITCK Digital I/O
GPIO3
Alternate function: SSI Bit Clock
31
43 SSI_FSYN Digital I/O
GPIO2
Alternate function: SSI Frame Sync
32
44 SSI_RX Digital I/O
GPIO1
Alternate function: SSI RX data input
33
45 SSI_TX Digital I/O SSI TX data output / GPIO0 34
46 KBI_7 Digital I/O
GPIO29
Alternate function: Keyboard Interface Bit 7
35
47 COIL_BK
Power Switch
Output
Buck Converter coil drive output 43
48 KBI_6 Digital I/O
GPIO28
Alternate function: Keyboard Interface Bit 6
36
49 RESETB Digital Input System reset input 51
50 LREG_BK_FB Power Input Voltage input to onboard regulators, buck regulator feedback voltage 44
51 GND GND GND 78
52 KBI_5 Digital I/O
GPIO27
Alternate function: Keyboard Interface Bit 5
37
53 KBI_4 Digital I/O
GPIO26
Alternate function: Keyboard Interface Bit 4
38
54 KBI_3 Digital I/O
GPIO25
Alternate function: Keyboard Interface Bit 3
39
55 KBI_2 Digital I/O
GPIO24
Alternate function: Keyboard Interface Bit 2
40
56 KBI_1 Digital I/O
GPIO23
Alternate function: Keyboard Interface Bit 1
41
57
KBI_0_HST
_WK
Digital I/O
GPIO22
Alternate function: Keyboard Interface Bit 0 / Host Walk-up output
42
58 GND GND GND 79
59 GND GND GND 86
60 GND GND GND 87
ZFSM-201 Series
Page 11
MODULE DIMENSIONS Dimensions in inches. Tolerances = +/-0.005 unless otherwise noted.
For layout recommendation for optimum antenna performance, refer to Antenna section in this document.
FreeStar PRO ZFSM-201-xC
FreeStar PRO ZFSM-201-x
RF Shield
0.895
1.413
Pitch = 0.05
1.000
0.062
.193
0.085
0.075
Pin 1
Pin 21 Pin 40
Pin 60
RF Shield
ZFSM-201-1
C6 J1
C12
C7
C11
C30
0006-00-00-00-001
ISSUE
RF Shield
J2 Connector
0.895
1.413
Pitch = 0.05
1.000
0.062
.193
0.085
0.075
Pin 1
Pin 21 Pin 40
Pin 60
RF Shield
ZFSM-201-1C
C6
C12
C7
C11
C30
0006-00-00-00-001
ISSUE
ZFSM-201 Series
Page 12
MODULE LAND FOOTPRINT

NOTE: Dimensions in inches. Tolerances = +/-0.005 unless otherwise noted.
1.100 [27.93]
0.308 [7.82]
0.050 [1.26]
0.050 [1.27]
60 X 0.040 [1.02]
60 X 0.100 [2.54]
1
.
1
5
5

[
2
9
.
3
4
]
1
.
0
4
0

[
2
6
.
4
2
]
0.890 [22.61]
0.104 [2.65]
1.000 [25.40]
COPPER KEEPOUT AREA
Figure 2
ZFSM-201 Series
Page 13
PROCESSING
Recommended Refow Profle
Parameters Values
Ramp up rate (from Tsoakmax to Tpeak) 3/sec max
Minimum Soak Temperature 150C
Maximum Soak Temperature 200C
Soak Time 60-120 sec
TLiquidus 217C
Time above TL 60-150 sec
Tpeak 250C
Time within 5 of Tpeak 20-30 sec
Time from 25 to Tpeak 8 min max
Ramp down rate 6C/sec max
Achieve the brightest possible solder fllets with a good shape and low contact angle.
Pb-Free Soldering Paste
Use of No Clean soldering paste is strongly recommended, as it does not require cleaning after the soldering process.
Note: The quality of solder joints on the castellations (half vias) where they contact the host board should meet the appropriate IPC
Specifcation. See IPC-A-610 Acceptability of Electronic Assemblies, section 8.2.4 Castellated Terminations.
Cleaning
In general, cleaning the populated modules is strongly discouraged. Residuals under the module cannot be easily removed
with any cleaning process.
Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and
the module. The combination of soldering fux residuals and encapsulated water could lead to short circuits between
neighboring pads. Water could also damage any stickers or labels.
Cleaning with alcohol or a similar organic solvent will likely food soldering fux residuals into the two housings, which is
not accessible for post-washing inspection. The solvent could also damage any stickers or labels.
Ultrasonic cleaning could damage the module permanently.
The best approach is to consider using a no clean soldering paste and eliminate the post-soldering cleaning step.
Optical Inspection
After soldering the Module to the host board, consider optical inspection to check the following:
Proper alignment and centering of the module over the pads.
Proper solder joints on all pads.
Excessive solder or contacts to neighboring pads, or vias.
Repeating Refow Soldering
Only a single refow soldering process is encouraged for host boards.
ZFSM-201 Series
Page 14
AGENCY CERTIFICATIONS
FCC Compliance Statement (Part 15.19) Section 7.15 of RSS-GEN
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning (Part 15.21)
Changes or modifcations not expressly approved by CEL could void the users authority to operate the equipment.

20 cm Separation Distance
To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter.
OEM Responsibility to the FCC Rules and Regulations
The FreeStar Pro Module has been certifed per FCC Part 15 rules for integration into products without further testing or
certifcation. To fulfll the FCC certifcation requirements, the OEM using the FreeStar Pro Module must ensure that the
information provided on the FreeStar Pro Label is placed on the outside of the fnal product. The FreeStar Pro Module is
labeled with its own FCC ID Number. If the FCC ID is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: Contains Transmitter Module FCC ID: W7Z-FSTARPRO or Contains
FCC ID: W7Z-FSTARPRO
The OEM using the FreeStar Pro Module must only use the approved antenna, (PCB Trace Antenna) that has been certi-
fed with this module. The OEM using the FreeStar Pro Module must test their fnal product confguration to comply with
Unintentional Radiator Limits before declaring FCC compliance per Part 15 of the FCC rules.
PROCESSING (Continued)
Wave Soldering
If a wave soldering process is required on the host boards due to the presence of leaded components, only a single wave
soldering process is encouraged.
Hand Soldering
Hand soldering is possible. Use a soldering iron temperature setting equivalent to 350C, follow IPC recommendations/
reference document IPC-7711.
Rework
The FreeStar Pro Module can be unsoldered from the host board. Use of a hot air rework tool and hot plate for pre-heating
from underneath is recommended. Avoid overheating.
!Warning Never attempt a rework on the module itself, e.g. replacing individual components. Such actions will terminate
warranty coverage.
Additional Grounding
Attempts to improve module or system grounding by soldering braids, wires, or cables onto the module RF shield cover
is done at the customers own risk. The numerous ground pins at the module perimeter should be suffcient for optimum
immunity to external RF interference.
ZFSM-201 Series
Page 15
AGENCY CERTIFICATIONS (Continued)
IC Certifcation Industry Canada Statement
The term "IC" before the certifcation / registration number only signifes that the Industry Canada technical specifcations
were met.
Section 14 of RSS-210
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF feld in
excess of Health Canada limits for the general population. Consult Safety Code 6, obtainable from Health Canada's
website: http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/99ehd-dhm237/index-eng.php
CE Certifcation Europe
The FreeStar Pro RF module has been tested and certifed for use in the European Union.
OEM Responsibility to the European Union Compliance Rules
If the FreeStar Pro module is to be incorporated into a product, the OEM must verify compliance of the fnal product to the
European Harmonized EMC and Low-Voltage / Safety Standards. A Declaration of Conformity must be issued for each of
these standards and kept on fle as described in Annex II of the R&TTE Directive.
The manufacturer must maintain the user's guide and adhere to the settings described in the manual for maintaining
European Union Compliance. If any of the specifcations are exceeded in the fnal product, the OEM is required to
make a submission to the notifed body for compliance testing.
OEM Labeling Requirements
The `CE' mark must be placed on the OEM product in a visible location.
The CE mark shall consist of the initials CE with the following form:
If the CE marking is reduced or enlarged, the proportions given in the above graduated
drawing must be adhered to.
The CE mark must be a minimum of 5mm in height
The CE marking must be affxed visibly, legibly, and indelibly Since the 2400 - 2483.5 MHz
band is not harmonized by a few countries throughout Europe, the Restriction sign must be
placed to the right of the `CE' marking as shown in the picture
ZFSM-201 Series
Page 16
SHIPMENT, HANDLING, AND STORAGE
Shipment
The FreeStar Pro Modules are delivered in trays of TBD.
Handling
The FreeStar Pro Modules are designed and packaged to be processed in an automated assembly line.
! Warning The FreeStar Pro Modules contain a highly sensitive electronic circuitry. Handling without proper ESD
protection may destroy or damage the module permanently.
! Warning According to JEDEC ISP, the FreeStar Pro Modules are moisture sensitive devices. Appropriate handling
instructions and precautions are summarized in Section 2.1. Read carefully to prevent permanent damage due to moisture
intake.
Moisture Sensitivity Level (MSL)
MSL 3, per J-STD-033
Storage
Storage/shelf life in sealed bags is 12 months at <40C and <90% relative humidity.
ZFSM-201 Series
Page 17
REFERENCES & REVISION HISTORY
References
Reference Documents
FreeStar Pro Module Evaluation Kit User Guide
FreeScale MC1322xV Datasheet
Freescale Semiconductor MC1322x Reference Manual MC1322xRM
Freescale Semiconductor BeeKit User Guide BKWCTKUG
Freescale Semiconductor Software Driver Reference Manual 22XDRVRRM
Freescale Semiconductor MC1322x Simple Media Access Controller (SMAC) Reference Manual 22xSMACRM
Freescale Semiconductor Simple Media Access Controller (SMAC) Users Guide SMACRM
IAR J-Link and IAR J-Trace user Guide J-Link_J-TraceARM-1
ARM IAR Embedded Workbench IDE User Guide UARM-13
Revision History
Previous Versions Changes to Current Version Page
0006-00-07-00-000
(Preliminary) October 28, 2008
Initial advance datasheet. N/A
0006-00-07-00-000
(Preliminary) May 20, 2009
Updated to current revisions to the Freescale Silicon IC N/A
0006-00-07-00-000
(Preliminary) June 11, 2009
Updated FCC and IC Agency Statements 14-15
0006-00-07-00-000
August 17, 2009
Updated RF Output Power Setting 6
0006-00-07-00-000
(Issue A) December 10, 2010
Added the MC13226 (ZFMS-201-2) Transceiver platform Option All
Disclaimer
The information in this document is current as of December, 2010. The information is subject to change without
notice. For actual design-in, refer to the latest publications of CEL data sheets or data books, etc., for the most
up-to-date specifcations of CEL products. Not all products and/or types are available in every country. Please
check with an CEL sales representative for availability and additional information.

No part of this document may be copied or reproduced in any form or by any means without the prior written
consent of CEL. CEL assumes no responsibility for any errors that may appear in this document.

CEL does not assume any liability for infringement of patents, copyrights or other intellectual property rights of
third parties by or arising from the use of CEL products listed in this document or any other liability arising from the
use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other
intellectual property rights of CEL or others.

Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these circuits,
software and information in the design of a customers equipment shall be done under the full responsibility of the
customer. CEL assumes no responsibility for any losses incurred by customers or third parties arising from the use
of these circuits, software and information.

While CEL endeavors to enhance the quality, reliability and safety of CEL products, customers agree and
acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to
property or injury (including death) to persons arising from defects in CEL products, customers must incorporate
suffcient safety measures in their design, such as redundancy, fre-containment and anti-failure features.