Physics 200

Problem Set 6
Solution
1. (i) What is the moment of inertia ICM of a propeller with three blades (treated as rods) of mass
m, length L, at 120 relative to each other? (ii) If a torque acts on this how long will it take to
reach an angular velocity ? (iii) How many revolutions will it have made before reaching this ?
(iv) Get the numerical answers if L = 1.25 m, m = 12 kg, = 3000 N m, = 2000 rad/s.
Answer:
(i) We know (if not, look on p. 296) that the moment of inertia of a single rod rotating around
its end is 31 mL2 . Its not hard to convince oneself that if there are three of them rotating
around the same axis and in the same plane, the moment of inertia is just three times this,
ICM = mL2 .
(ii) Since = t and = ICM ,
t=

mL2
ICM
=
.

(iii) From our knowledge of constant acceleration problems,

2 = 2 = =

ICM 2
mL2 2
2
=
=
.
2
2
2

The number of revolutions it made is

N=

mL2 2

=
.
2
4

(iv)
ICM = (12 kg)(1.25 m)2 = 19 kg m2 ,
(12 kg)(1.25 m)2 (2000 s1 )
= 13 s,
2(3000 N m)
(12 kg)(1.25 m)2 (2000 s1 )2
N=
= 2000.
4(3000 N m)
t=

2. Consider I for a rectangle of sides a (along the y-axis) and b (along the x-axis) about the two
symmetry axes. (Rotate the rectangle about one of these axes and think of it as composed of
1
M a2 . Going back to the very definition of
rods.) Show that about the axis parallel to x, I = 12
I, show that if this rectangle is spun around an axis through its CM and perpendicular to its area
1
M (a2 + b2 ).
the moment of inertia will be I = 12
Answer: To find Ix , the moment of inertia about the symmetry axis parallel to the x-axis, we
think of dividing the rectangle into many thin rods:

a
x

Since each rod has length a, it should be obvious that the sum of these contributions is simply
1
2
12 M a , i.e., the same as if there was one rod of mass M rotating around the axis, but lets be more
explicit. If we divide up the rectangle into n rods (where n is large so they really are rods, though
in the end it doesnt matter) so that each rod has mass M/n, then with each rod contributing
1 M
1
2
2
12 ( n )a and there being n rods, we get Ix = 12 M a as expected. The same logic of course applies
to the symmetry axis parallel to the y-axis.
From the definition of the moment of inertia,
I=

ri2 mi .

Notice from the picture that

ri2

= (xi b/2) + (yi x/2)2 , so we can write

(xi,yi)

(b/2,a/2)

2
X
X
a 2
1
b
mi +
yi
mi = Iy + Ix = Ix + Iy =
M (a2 + b2 ).
I=
xi
2
2
12
i
i
Its easy to see that this kind of argument will work for any flat object, as long as you choose your
axes to be perpendicular to each other.
3. A 4.8 kg block is resting at the top of a 30 slope of height 1 m. It is attached to a cylindrical pulley
of mass 1.7 kg and radius 8 cm by a massless string that unwinds as the block slides downhill. If
the acceleration of the block is 1.9 m/s2 what is k ? Find the velocity at the bottom of the slope
using forces and torques. Repeat using energy ideas. See Fig. 1.
Answer: Numbers are cumbersome, so lets start by letting m be the mass of the block, the
angle, h the height, M the mass of the pulley, R its radius, and a the acceleration felt by the block.
As usual, we decompose the forces on the block into those that are parallel to the slope and those
that are perpendicular to the slope. In the perpendicular direction, the component of gravity in
this direction mg cos balances the normal force, so N = mg cos . In the parallel direction, we
have
mg sin T fk = ma
2

Figure 1: The block started at height h.

(we take downhill to be positive), where the kinetic friction term is given by fk = k N =
k mg cos . We now need the tension T , which we find as follows. The acceleration a that the
block feels is converted to angular acceleration in the pulley, where a = R. But we also know
that = RT = I where I = 21 M R2 is the moment of inertia of the pulley. Therefore
T =

Ia
1
I
= 2 = M a,
R
R
2

and plugging into the above equation we get

fk = mg sin T ma = mg sin

M
+ m a.
2

Then

mg sin (M/2 + m)a

fk
=
.
mg cos
mg cos
Before plugging in the numbers, note that we can make our lives just a little easier by rearranging
a little bit:
k =

k =

sin 30 [1 + ((1.7 kg)/2(4.8 kg))(1.9 m/s2 )/(9.81 m/s2 )

sin (1 + M/2m)a/g
=
= 0.31.
cos
cos 30

Since the block travels a distance d = h/ sin , the velocity at the bottom of the slope, starting
from rest at the top, is
r
r
2ah
2(1.9 m/s2 )(1 m)
2ah
2
= v =
=
= 2.8 m/s.
v = 2ad =
sin
sin
sin 30
The energy method is somewhat more involved. At the top, the energy of the block is purely
potential energy, mgh. At the bottom, the potential energy is zero, the kinetic energy of the block
is T = 21 mv 2 , and the rotational kinetic energy of the pulley is

1
1 2
1 1
v 2
2
I =
MR
= M v2 .
2
2 2
R
4
Some energy was also lost to friction, so we must take that into account. The work done by friction
is
k mgh
h
=
.
fk d = k mg cos
sin
tan
We can finally use the conservation of energy in the form
mgh =

1
1
k mgh
mv 2 + M v 2 +
,
2
4
tan
3

which means

v=

s
2gh(1 k / tan )
=
1 + M/2m

2(9.81 m/s2 )(1 m)(1 0.31/ tan 30 )

= 2.8 m/s.
1 + (1.7 kg)/2(4.8 kg)

As one would expect, the two answers agree.

4. Argue that that A (A B) = 0. In three dimensions find the expression of A B in terms of

vector components and i, j, and k.

Answer: Since A B is always perpendicular to both A and B, the dot product with A must be
zero. For the second part, we use the basic relations
i i = j j = k
k
= 0,

i j = j i = k,

j k
= k
j = i,

i = i k
= j.
k

Thus when we expand the cross product, we can immediately drop any term that contains the
same unit vector twice:
(Bxi + Byj + Bz k)

A B = (Axi + Ayj + Az k)
+ Ay Bx (j i) + Ay Bz (j k)
+ Az Bx (k
i) + Az By (k
j)
= Ax By (i j) + Ax Bz (i k)

= (Ay Bz Az By )i + (Az Bx Ax Bz )j + (Ax By Ay Bx )k.

We can also check that
A (A B) = Ax (Ay Bz Az By ) + Ay (Az Bx Ax Bz ) + Az (Ax By Ay Bx ) = 0,
as we argued.
5. A disk of radius R and mass M is spinning at an angular velocity 0 rad/s. A non-rotating
concentric disk of mass m and radius r drops on it from a negligible height and the two rotate
together. (See Fig. 2). Find the final and fraction of initial kinetic energy left.

m, r

M, R

Figure 2: The upper disk, initially at rest, falls with

negligible speed on the lower one which is spinning.
Their centers coincide.

Answer: Let IM = 21 M R2 be the moment of inertia of the disk of radius R, and Im = 21 mr2 the
moment of inertia of the other disk. Initially the angular momentum of the system is IM 0 , and
when the two disks are rotating together the angular momentum is (IM + Im ). Since angular
momentum is conserved,
IM 0 = (IM + Im ) = =
4

0
IM 0
=
.
IM + Im
1 + mr2 /M R2

Before the second disk is added, the rotational kinetic energy of the system is 21 IM 02 , and afterward
the kinetic energy is 21 (IM + Im ) 2 . Therefore the fraction of the initial kinetic energy left is
1
2
2 (IM + Im )
1
2
2 IM 0

IM + Im
=
IM

IM + Im
=
IM

IM
IM + Im

2
=

IM
1
=
.
IM + Im
1 + mr2 /M R2

Evidently the kinetic energy is conserved only if the initially rotating disk has infinite moment of
inertia, or if the second disk has no moment of inertia.
6. A gyro consists of a solid disk of radius R mounted at one end of a shaft of zero mass and length
l, the other end of which is on a pivot. The disk spins at rad/s and the gyro precesses at p
rad/s. What is l in terms of p , , g and R? Give a number for l when R = 6 m, p = 2.6 rad/s,
and the disc is spinning at 450 rpm?
Answer: Note that the mass of the disk is not given in this problem, so well say the mass is M
and see why it doesnt matter what the mass is. The magnitude of the angular momentum is
L = I = 21 M R2 . Since gravity acts at distance l from the pivot, the torque produced by the
force = M gl, and so the equation for a gyroscope tells us
p =

M gl

2gl
=
= 2 .
2
L
M R /2
R

As we hoped, the mass has canceled from the equation. Solving for the length of the shaft gives
l=
450 rpm is
450 rpm
so
l=

R2 p
.
2g

2 rad 1 min
= 47 rad/s,
1 rev 60 s

(6 m)2 (47 s1 )(2.6 s1 )

= 220 m,
2(9.81 m/s2 )

which is quite a large number.

7. Two beads of mass m are free to slide on a rod of length l and mass M as in Fig. 3. Initially the
beads are at the center and the rod is spinning freely (with no external torque) at 0 rad/s about
a vertical axis through its center. Slowly the beads move radially out (at negligible velocity). (i)
Find (r), the angular velocity when the beads are r m from the center. (ii) What is when they
just fly tangentially off the rod? Argue that does not change hereafter. (Hint: Using the formula
L = r p for the angular momentum of beads show that their Ls do not change even though rs
do. Also are there any torques on the spinning rod after the beads detach?) (iii) Why was the
force of friction between beads and rod unimportant in the preceding discussion?
Answer:
(i) Initially the moment of inertia of the system is due only to the rod, because r = 0 for
1
M l2 , and the angular momentum is L = I0 0 . If the beads are a
the beads. So I0 = 12
distance r from the center, each one contributes mr2 to the systems moment of inertia, so
I(r) = I0 + 2mr2 . Since angular momentum is conserved, I0 0 = I, or
(r) =

I0 0
0
I0 0
0
=
=
.
=
2
2
I
I0 + 2mr
1 + 2mr /I0
1 + 24mr2 /M l2
5

Figure 3: The point-like beads can slide along the rod

which is spinning around a vertical axis through its
CM. The beads start out at the center of the rod.

(ii) The beads fly off the rod when r = l/2, so at this time

0
l
=

.
2
1 + 6m/M
Once the beads fly off the rod, they continue moving in a straight line at constant velocity,
so p is a constant. For each bead the angular momentum L = r p points out of the page
in the figure and has magnitude |r||p| sin . Since |p| stays constant, the angular momentum
depends entirely on the quantity |r| sin , and looking at the figure below where the position
of one of the beads is indicated at two different times after flying off the rod, we see that
|r1 | sin = |r2 | sin = l/2. The same logic applies to the other bead, so that L for the beads
does not change once they leave the rod. This in turn means that the remaining angular
momentum, the angular momentum possessed by the rod, does not change either, and since
the moment of inertia of the rod stays put its angular velocity must remain constant, too.
m

l/2

l/2
r1
p

r2

(iii) While the beads are on the rod, the force of friction F acts in the same direction as the position
r, so the torques are rF = 0. But it is torques, and not forces, that affect rotational motion,
so F can have no effect. This applies to when the beads are on the rod; once they leave the
rod, there is of course no friction.
8. A sphere of radius R is supported by a rope attached to a wall as shown in Fig. 4. The rope makes
an angle with respect to the wall. The point where the rope is attached to the ball is such that
if the line of the rope is extended it crosses the horizontal line through the center of the ball at
a distance 3R/2 from the wall. Show that the minimum s between wall and ball for this to be
6

possible is s = 21 cot . Evaluate this for = 30 . Hint: Find the right place to take torques. The
usual suspects will not do.

3R/2

Figure 4: The rope is attached to the wall at one end

and the ball at the other. If extrapolated, the line of
the rope crosses the horizontal line going through the
center at a distance 3R/2 from the wall.

Answer: We need to balance both the forces and the torques, and it is the latter that is tricky
here. So consider the figure below:

P
fs
N
A

Mg

In order to make calculating the torque due to the rope simple, we should choose point O as the
point around which we take torques. Then the tension in the rope has no component perpendicular
to OP and hence applies no torque in our system. The forces that do apply a torque are the force
of gravity acting downward at C, so that g = M gR/2, and the force of friction acting upward
at A, so that f = 3Rfs /2, where fs is the force of static friction. These torques act in opposite
directions, so g = f implies
3Rfs
Mg
M gR
=
= fs =
.
2
2
3
We can now use our old tools to find fs . In the horizontal direction, the normal force N balances the
horizontal component of the tension T sin , so N = T sin . In the vertical direction, the vertical
component of the tension T cos and force of friction fs = s N balance the force of gravity M g:
T cos + fs = M g.
7

Substituting T = N/ sin = fs /s sin , we get

Mg
cot
cot
fs = 1 +

= M g,
1+
s
s
3
or

3
cot
cot
= 3 = s =
=
= 0.87
1+
s
2
2

if = 30 .
9. A horizontal rod of mass 8 kg and length 2.4 m is hinged to a wall and supported by a cable that
makes an angle of 25 as shown in Fig. 5. What is the tension T on the cable and what is the force
exerted by the pivot? Repeat if in addition a 25 kg weight is suspended at the end of the rod.

2.4 m

25

Figure 5: The rope is attached to the wall at one end

and the rod at the other. P is the pivot.

Answer: If we choose the pivot as the center of torque, then the nonzero torques acting on the rod
are due to gravity, g = M gl/2, and the vertical component of the tension, r = T l sin . These
act in opposite directions and balance each other, so that
M gl
Mg
(8 kg)(9.81 m/s2 )
= T l sin = T =
= 93 N.
=
2
2 sin
2 sin 25

Fy
T

Fx

Mg

Since the tension has a leftward component and gravity acts entirely downward, the pivot must
exert a force to the right, Fx = T cos = M2g cot , to balance the tension. In the vertical direction,
we have
Mg
Mg
= M g = Fy =
.
Fy + T sin = Fy +
2
2
8

Therefore the force exerted by the pivot is

F=

Mg
(8 kg)(9.81 m/s2 )
) =
) = (84 N)
+y
) = (39 N)(2.1
(cot
x+y
(cot 25 x
x+y
x + (39 N)
y.
2
2

If, in addition, an object of mass m is attached to the end of the rod, there is an additional torque
mgl that counters the torque due to tension:
T 0 l sin =

(9.81 m/s2 )[(8 kg)/2 + 25 kg]

M gl
g(M/2 + m)
+ mgl = T 0 =
=
= 670 N.
2
sin
sin 25

The horizontal force is again given by

Fx0 = T 0 cos = g

M
+ m cot ,
2

while the vertical force is given by

Fy0

+ T sin =

Fy0

+g

M
Mg
+ m = (M + m)g = Fy0 =
.
2
2

Therefore

Mg
8 kg
M
(8 kg)(9.81 m/s2 )
=

+
+ m g cot
x+
y
+ 25 kg (9.81 m/s2 ) cot 25 x
y
F0 =
2
2
2
2
= (610 N)
x + (39 N)
y.
10. A ladder of length 6 m mass 15 kg leans against a wall at angle 30 with respect to the wall. With
respect to the ground it has s = 0.4. How high can a 70 kg man climb before the ladder slips?
Answer: The forces in the problem are shown below, where we call the mass of the ladder M and
the mass of the man m. Suppose the man is standing at height h. Since there are two forces acting
at the point where the ladder meets the floor, we can get rid of some torques by choosing this
point as the origin.

N2

h
N1
mg Mg

fs
O

The nonzero torques due to N2 , M g, and mg balance:

N2 l cos =

N2 l cos2 M l cos
mgh
1
M gl sin +
sin = h =

.
2
cos
mg sin
2m

From the balance of forces in the vertical direction we get N1 = (M + m)g, and from the horizontal
direction we get (actually, what we want is N2 fs so the ladder doesnt slip, which is why h is
the maximum value for which the ladder will not slide)
N2 = fs = s N1 = s g(M + m).
Plugging into the above expression for h gives

M
M
cot
h = l cos s 1 +
m
2m

15
kg
15 kg

= (6 m) cos 30 0.4 1 +
cot 30
= 3.8 m.
70 kg
2(70 kg)

10