Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

LG 26lh1dc1-Ub PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 72

Internal Use Only

website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html

LCD TV
SERVICE MANUAL
MODELS : 26LH1DC1-UB
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : 3350GDKM0020A

December, 2007

CONTENTS

CONTENTS............................................................................................... 2
SAFETY PRECAUTIONS ..........................................................................3
SPECIFICATION ........................................................................................6
ADJUSTMENT INSTRUCTION................................................................11
SVC REMOCON ......................................................................................21
TROUBLE SHOOTING GUIDES .............................................................22
TROUBLE SHOOTING ............................................................................24
BLOCK DIAGRAM...................................................................................27
VIDEO AND AUDIO SIGNAL FLOW CHART .........................................34
WIRING DIAGRAM ..................................................................................46
EXPLODED VIEW....................................................................................47
EXPLODED VIEW PARTS LIST ..............................................................48
REPLACEMENT PARTS LIST ................................................................49
SVC. SHEET ................................................................................................

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-2-

LGE Internal Use Only

SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by
in the
Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

Leakage Current Hot Check (See below Figure)


Plug the AC cord directly into the AC outlet.

General Guidance
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.

Do not use a line Isolation Transformer during this check.


Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.

It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1W), keep the resistor 10mm away from PCB.

Leakage Current Hot Check circuit


Keep wires away from high voltage or high temperature parts.

AC Volt-meter
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
To Instrument's
exposed
METALLIC PARTS

Leakage Current Cold Check(Antenna Cold Check)


With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1M and 5.2M.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

0.15uF

Good Earth Ground


such as WATER PIPE,
CONDUIT etc.

1.5 Kohm/10W

-3-

LGE Internal Use Only

SERVICING PRECAUTIONS
2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES
devices.
4. Use only an anti-static type solder removal device. Some solder
removal devices not classified as "anti-static" can generate
electrical charges sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate
electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective
package until immediately before you are ready to install it.
(Most replacement ES devices are packaged with leads
electrically shorted together by conductive foam, aluminum foil
or comparable conductive material).
7. Immediately before removing the protective material from the
leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be
installed.
CAUTION : Be sure no power is applied to the chassis or
circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged
replacement ES devices. (Otherwise harmless motion such as
the brushing together of your clothes fabric or the lifting of your
foot from a carpeted floor can generate static electricity
sufficient to damage an ES device.)

CAUTION : Before servicing receivers covered by this service


manual and its supplements and addenda, read and follow the
SAFETY PRECAUTIONS on page 3 of this publication.
NOTE : If unforeseen circumstances create conflict between the
following servicing precautions and any of the safety precautions on
page 3 of this publication, always follow the safety precautions.
Remember: Safety First.
General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC power
source before;
a. Removing or reinstalling any component, circuit board
module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical plug or
other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver.
CAUTION : A wrong part substitution or incorrect polarity
installation of electrolytic capacitors may result in an
explosion hazard.
2. Test high voltage only by measuring it with an appropriate high
voltage meter or other voltage measuring device (DVM,
FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
3. Do not spray chemicals on or near this receiver or any of its
assemblies.
4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable
non-abrasive applicator; 10% (by volume) Acetone and 90% (by
volume) isopropyl alcohol (90%-99% strength)
CAUTION : This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication of
contacts in not required.
5. Do not defeat any plug/socket B+ voltage interlocks with which
receivers covered by this service manual might be equipped.
6. Do not apply AC power to this instrument and/or any of its
electrical assemblies unless all solid-state device heat sinks are
correctly installed.
7. Always connect the test receiver ground lead to the receiver
chassis ground before connecting the test receiver positive
lead.
Always remove the test receiver ground lead last.
8. Use with this receiver only the test fixtures specified in this
service manual.
CAUTION : Do not connect the test fixture ground strap to any
heat sink in this receiver.

General Soldering Guidelines


1. Use a grounded-tip, low-wattage soldering iron and appropriate
tip size and shape that will maintain tip temperature within the
range or 500F to 600F.
2. Use an appropriate gauge of RMA resin-core solder composed
of 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean and well tinned.
4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle.
Do not use freon-propelled spray-on cleaners.
5. Use the following unsoldering technique
a. Allow the soldering iron tip to reach normal temperature.
(500F to 600
F)
b. Heat the component lead until the solder melts.
c. Quickly draw the melted solder with an anti-static, suctiontype solder removal device or with solder braid.
CAUTION : Work quickly to avoid overheating the
circuitboard printed foil.
6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
(500F to 600
F)
b. First, hold the soldering iron tip and solder the strand against
the component lead until the solder melts.
c. Quickly move the soldering iron tip to the junction of the
component lead and the printed circuit foil, and hold it there
only until the solder flows onto and around both the
component lead and the foil.
CAUTION : Work quickly to avoid overheating the circuit
board printed foil.
d. Closely inspect the solder area and remove any excess or
splashed solder with a small wire-bristle brush.

Electrostatically Sensitive (ES) Devices


Some semiconductor (solid-state) devices can be damaged easily
by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES
devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques
should be used to help reduce the incidence of component
damage caused by static by static electricity.
1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any electrostatic
charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the
unit under test.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-4-

LGE Internal Use Only

Circuit Board Foil Repair


Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
following guidelines and procedures should be followed whenever
this condition is encountered.

IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong) through
which the IC leads are inserted and then bent flat against the
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique
as outlined in paragraphs 5 and 6 above.

At IC Connections
To repair a defective copper pattern at IC connections use the
following procedure to install a jumper wire on the copper pattern
side of the circuit board. (Use this technique only on IC
connections).

Removal
1. Desolder and straighten each IC lead in one operation by gently
prying up on the lead with the soldering iron tip as the solder
melts.
2. Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing the
IC.
Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and
solder it.
3. Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).

1. Carefully remove the damaged copper pattern with a sharp


knife. (Remove only as much copper as absolutely necessary).
2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
carefully crimp it around the IC pin. Solder the IC connection.
4. Route the jumper wire along the path of the out-away copper
pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
excess jumper wire.

"Small-Signal" Discrete Transistor


Removal/Replacement
1. Remove the defective transistor by clipping its leads as close as
possible to the component body.
2. Bend into a "U" shape the end of each of three leads remaining
on the circuit board.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder
each connection.

At Other Connections
Use the following technique to repair the defective copper pattern
at connections other than IC Pins. This technique involves the
installation of a jumper wire on the component side of the circuit
board.
1. Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.
2. Trace along the copper pattern from both sides of the pattern
break and locate the nearest component that is directly
connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead of the
nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION : Be sure the insulated jumper wire is dressed so the
it does not touch components or sharp edges.

Power Output, Transistor Device


Removal/Replacement
1. Heat and remove all solder from around the transistor leads.
2. Remove the heat sink mounting screw (if so equipped).
3. Carefully remove the transistor from the heat sink of the circuit
board.
4. Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6. Replace heat sink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of the
two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.
CAUTION : Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-5-

LGE Internal Use Only

SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.

1. Application range
1.1 This spec sheet is applied all of the 26" LCD TV with PPV&PILLOW SPEAKER.
1.2 Not included spec and each product spec in this spec sheet apply correspondingly to thefollowing each country standard and
requirement of Buyer.

2. Specification
Each part is tested as below without special appointment.
2.1 Temperature : 20 5C
2.2 Relative Humidity : 65 10%
2.3 Power Voltage : input voltage(100~240V@50/60Hz)
* Standard Voltage of each product is marked by models.
2.4 Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.
2.5 The receiver must be operated for about 20 minutes prior to the adjustment.

3. General Specification(TV)
Item
Input Signal

Specification
Receiving System
Sound Effect
Available Channel

Input Voltage
Market
Screen Size
Aspect Ratio
Tuning System
LCD Module

Video

Audio
Antenna
External Input

Stream Compression
Receiving Signal
Display Interface
Digital Comb-filter
Demodulation
Speaker Power
Impedance
AV Input
S-Video Input
Component Input
PC Input
HDMI Input
Service Port
PILLOW SPEAKER Input
MPI Input

Digital Audio Output


Function
OSD Language
Program Guide
Digital Noise Reduction
Caption
Channel Add/Delete
Channel Preview
Signal strength Display
PPV&PRO : IDIOM

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

Digital : ATSC/64&256QAM, Analog : NTSC


Dolby Digital(AC-3)
Air
CH2~CH69
Cable
CH1~CH135
AC 100~240V(50/60Hz)
North America
26 inch Wide
16:9
FS
LC260WX2-SLB2
LPL
LC260WX2-SLB1
LPL
LC260WX2-SLA1
LPL
MPEG2 MP@HL
8VSB, Clear QAM(64, 256), NTSC
LVDS 1366X768
Support : 3D Y/C-NTSC Signal
Dolby Digital(AC3)
RMS 7.5W+7.5W(8 load)
75 Unbalanced, F-Type Jack, VHF/UHF Tuner
CVBS : 3, L/R Audio : 3, Auto-Cam port(AV2)
Y/C : 1
YPbPr(480i~1080i) : 2, L/R Audio : 2
D-sub15(Max 1366X768 pixel, 60Hz), Phone Jack(Audio)
480i, 480p, 720p, 1080i
DSUB 9P Jack(RS-232)
DIGITAL PILLOW SPEAKER
RJ11 Jack
SPDIF(Optical)
English, Spanish, French
MINI-EPG
Support
EIA608, EIA708
Support
Support
Support
Support

-6-

LGE Internal Use Only

4. DTV Characteristics
4.1 General Specification

Item

Specification

Unit

VSB Reception Channel


QAM Reception Channel
Video Resolution
QAM Resolution
VSB / QAM RF Input

2 ~ 69CH(DTV)
1 ~ 135CH(CADTV)
ATSC 18 FORMAT
Sanoff OpenCable FORMAT
75 unbalanced input
F-type CONNECTOR input
Under 3.0

Sec.

0~-80
Fo +/-250
Fo +/-170

dBm
KHz
KHz

CH UP/DOWN :
Time for stable Sync
RF Dynamic Range
VSB AFC Range
QAM AFC Range

Remark

4.2 Digital Receive Part : 8T VSB Standard

Item

Min

Dynamic Range
White Noise(SNR)
Channel Pull-in Range
N/D Co-channel
Ps=7Db , Color Bar
400Hz, 25kHz Dev
N/D Upper Adj-Ch
PS=75Db, Color Bar
400Hz, 25kHz Dev
N/D Lower Adj-Ch
PS=75Db , Color Bar
400Hz, 25kHz Dev

-82
-250

Static Ghost
(0.2usec)
Static Ghost
(0.3usec)
Static Ghost
(1.0usec)
Static Ghost
(5.0usec)
Doppler Ghost
(0.1 usec)

Doppler Ghost
(0.2 usec)

Max

Unit

Remark

-5
15.5
250

dBm
dB
KHz

2CH, 3CH, UHF : -80dBm

DTV(-30dBm)

dB

DTV(-60dBm)

dB

DTV(-60dBm)

35

42

dB

DTV(-60dBm)

35

42

dB

Ensemble Ghost
(ATTC recommend)
Static Ghost
(0.1usec)

Typ

A~G
0
90
180
0
90
180
0
90
180
0
90
180
0
90
180
0.2Hz
0.5Hz
1.0Hz
2.0Hz
5.0Hz
0.2Hz
0.5Hz
1.0Hz
2.0Hz
5.0Hz

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

OK
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
4
4
4
4
4
4
4
4
4

-7-

<TEST EQUIPMENT>
ROHDE & SCHWARZ
TV TEST TRANSMETER

dB

dB

dB

dB

dB

dB

dB

LGE Internal Use Only

Item

Min

Doppler Ghost
(0.3 usec)
(1.0 usec)
(5.0 usec)

Typ

Max

Unit

4
4
4
4
4

dB

Max

Unit

Remark

-32.0
-32.0
27
34
170

dBm
dBm
dB
dB
KHz

Input RF Level : -50.0 dBm

21

dB

DTV(-40dBm)

16

dB

DTV(-40dBm)

0.2Hz
0.5Hz
1.0Hz
2.0Hz
5.0Hz

Remark

4.3 Digital Receive Part : 64/256 QAM

Item

Min

Dynamic Range

-69.0
-63.0

64 QAM
256 QAM
White Noise(SNR)
64 QAM
256 QAM
Channel Pull-in Range (64/256 QAM)
N/D Upper Adj-Ch
64 QAM
PS=75Db, Color Bar
256 QAM
400Hz, 25kHz Dev

Typ

-170

4.4 Video Inputs

Content

Unit

Spec
Typ

Min

Remark
Max

VIDEO
Input

CVBS
-Active Video
-Sync
S-Video
-Active Video
-Sync
-Color Burst
Component
-Y/Pb/Pr
-Sync
RGB Input
-R/G/B
-H/V

mV

644
258

mV

644
258
258

mV

630
270

mV

630

1V
714
286
1V
714
286
286
1V
700
300
700
TTL

480i
786
314
786
314
314
480i/480p/720p/1080i
770
330
770

DTV : 480i/480p/720p/1080i
PC : *See 5. Signal Timing

4.5 Audio

Content

Unit

Spec
Typ

Min

Remark
Max

AUDIO (Dolby Digital 2CH Out)


OPTICAL
OUTPUT
ANALOG
AUDIO
OUT

UI(EYE PATTERN)
CATEGORY
CODE
REF. LEVEL
-LEFT
-RIGHT
MAX. LEVEL
-LEFT
-RIGHT
SEPERATION
-LEFT
-RIGHT
FREQ.
RESPONSE
-LEFT
-RIGHT

20
64(HEX)

IEC958 COMPOSITE AC-3

@1kHz, -20dBFs
mVrms

200
200

Vrms

2
2

dB

-60
-60

dB

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-19.5

-21

-8-

@20Hz~20kHz
@ 0.5dB ~ -1.0dB

LGE Internal Use Only

THD+N vs FREQ.
-LEFT
-RIGHT
THD vs LEVEL
-LEFT
-RIGHT
*DYNAMIC
RANGE
-16BIT(L, R)
-18BIT(L, R)
-20BIT(L, R)

dBFs

-60
-60

dBFs

-60
-60

@-20dBFs

-65
-65
-65

dB

*Dynamic Range Control (DRC) is originally the concept of Dolby Digital and used only in Dolby Digital.
But as a similar concept there is the Automatic Volume Correction in the analog TV, and it is used in the same menu
because there is no possibility of conflict between the two.
Therefore, if you turn on the DRC in the menu, the DRC will be active in the digital TV and AVC will be active in the analog TV.

5. Signal Timing (Resolution)


5.1 Component Video Input (Y, CB/PB, CR/PR)

No.

Resolution

H-freq.(kHz)

V-freq.(Hz)

Pixel Clock(MHz)

Proposed

720*480

15.75

60

13.51

SDTV, 480i

720*480

15.734

59.94

13.5

SDTV, 480i

720*480

31.5

60

27.03

SDTV, 480p

720*480

31.469

59.94

27

SDTV, 480p

1280*720

45

60

74.25

HDTV,720p

1280*720

44.96

59.94

74.18

HDTV,720p

1920*1080

33.75

60

74.25

HDTV,1080i

1920*1080

33.72

59.94

74.18

HDTV,1080i

5.2 PC Mode (RGB)

No.

Resolution

H-freq.(kHz)

V-freq.(Hz)

Pixel Clock(MHz)

Proposed

640*350

31.469

70.087

25.17

EGA

720*400

31.469

70.087

28.32

DOS

640*480

31.469

59.94

25.175

VGA

640*480

37.5

75

31.5

VGA

640*480

43.269

85.008

36

VGA

800*600

37.879

60.317

40

SVGA

800*600

46.875

75

49.5

SVGA

800*600

53.674

85.061

56.25

SVGA

832*624

49.726

75.552

58.05

MAC

10

1024*768

48.363

60.004

65

XGA

11

1024*768

60.023

75.029

78.75

XGA

12

1024*768

68.677

84.997

94.5

XGA

13

1280*720

44.772

59.855

74.5

VESA

14

1360*768

47.72

59.799

84.75

VESA

15

720*480

31.5

60

31.5

SDTV, 480p

16

720*480

31.469

59.94

59.94

SDTV, 480p

17

1280*720

45

60

74.25

HDTV, 720p

18

1280*720

44.96

59.94

74.18

HDTV, 720p

19

1920*1080

33.75

60

74.25

HDTV, 1080i

20

1920*1080

33.72

59.94

74.18

HDTV, 1080i

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-9-

LGE Internal Use Only

5.3 DVI/HDMI Input : HDMI Ver1.2a

No.

Resolution

H-freq.(kHz)

V-freq.(Hz)

Pixel Clock(MHz)

Proposed

640*480

31.469

59.94

25.17

VGA

640*480

37.861

72.8

31.5

VGA

640*480

37.5

75

31.5

VGA

640*480

43.3

85

36

VGA

800*600

35.156

56.25

36

SVGA

800*600

37.879

60.31

40

SVGA

800*600

48.077

72.18

50

SVGA

800*600

46.875

75

49.5

SVGA

800*600

53.7

85

56.25

SVGA

10

1024*768

48.363

60

65

XGA

11

1024*768

56.476

70.06

75

XGA

12

1024*768

60.023

75.02

78.75

XGA

13

1024*768

68.7

85

94.5

XGA

14

1280*768

47.78

59.87

79.5

15

1360*768

47.72

59.8

84.75

16

720*400

31.43

70

27.28

DOS

17

720*480

15.75

60

27.03

SDTV, 480i

18

720*480

15.734

59.94

27

SDTV, 480i

19

720*480

31.5

60

31.5

SDTV, 480p

20

720*480

31.469

59.94

59.94

SDTV, 480p

21

1280*720

45

60

74.25

HDTV, 720p

22

1280*720

44.96

59.94

74.18

HDTV, 720p

23

1920*1080

33.75

60

74.25

HDTV, 1080i

24

1920*1080

33.72

59.94

74.18

HDTV, 1080i

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-10-

LGE Internal Use Only

ADJUSTMENT INSTRUCTION
1.2 Service Menu Description

1. Service Menu
To enter the Service Menu, press the MENU button of the TV SET for
5 seconds while keeping the MENU key of the INSTALLER remote
controller pressed.
When using the Service Remote controller, press the IN-START or
ADJ to enter the Service Menu.
Use the channel UP/DOWN key to move between the items of the
Service Menu.
In the Service Menu, use the left and right key or volume key to adjust the
value in the Sub Item.
In the Service Menu, press ENTER to return to the Main Item from the
Sub Item.
Press exit in the main item to end the Service Menu.
Unlike other OSD, the Service Menu does not have any Timeout Exit.

(2) Software Version :


This shows you the information of the current Software Version.
The displayed information includes Version, Date, Model name and
Panel information.
(3) Chip I2C Test :
It shows you whether there is any issue in the HW of the major Device
on the Board at its basic level.
(4) Aging Test :
When you press Confirm, the service menu OSD temporarily
disappears and single color Pattern is displayed.
When you press ENTER key, it returns to its original condition.

1.1 Service Menu Structure


System Reset Confirm
Software Version
Chip I2C Test Memory
FLASH
EEPROM
TUNER
VIDEO ADC
AUDIO DEC
Uart1 Comm.
Pillow Mode
Uart Mode
Aging Test
White Balance Offset R
Offset G
Offset B
Gain R
Gain G
Gain B
YPbPr : offset/gain Offset Y
Offset Pb
Offset Pr
Gain Y
Gain Pb
Gain Pr
Reset Mode
RGB : offset/gain Offset R
Offset G
Offset B
Gain R
Gain G
Gain B
Reset Mode
Auto Picture Auto Brightness
Auto Contrast
Running Time - Running Time
Reset Mode
System All Reset Confirm
Audio Delay DTV
ATV/CVBS/YC
COMP/PC/HDMI
Reset Mode
AI Control
Last Power Save
Panel Monitoring
Panel ID Display ID
Panel Company ID
Model ID
Reserved
Commercial Flag
Panel Brightness
Epg Mode
SW Upgrade
EXIT

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

(1) System Reset :


When you press Confirm, the general NVRAM parameters excluding
the parameters of the service scope are initialized and self rebooted.
(This is mainly used after repairing or replacing the board to set to the
initial factory condition.)

(5) White Balance :


Control the offset/gain of the final end of the Scaler to adjust the white
balance. The adjustment is done by controlling the each offset/gain of
R, G and B.
The Color temperature is adjusted during HDMI 720p Input based on
9800K500 in 100% White pattern.
(Default : Offset R, G, B=50, 50, 50/Gain R, G, B = 50, 50, 50)
(6) YPbPr : offset/gain : Mst9883C Adjust
Calibrate the Offset/Gain of Mst9883(Video AD).
Because the deviation of Mst9883 is not significant, it does not need
separate calibration.
(Default : Offset Y, Pb, Pr=24, 51, 51/Gain Y, Pb, Pr = 60, 60, 60)
(7) RGB : offset/gain : RTD2023B Adjust
Calibrate the Offset/Gain of the Scaler for PC input process.
After connecting 16-gray or 32-gray pattern to RGB input and selecting
RGB : offset/gain, press ENTER button on the remote controller.
When the Reset Mode is shown, press the right arrow key on the
remote controller to execute auto calibration.
Scaler checks the gray pattern of input and calibrates the offset and
gain automatically to show you the values.
(Default : Offset R, G, B=128, 128, 128/Gain R, G, B = 128, 128, 128)
(8) Auto Picture :
Adjust the range of brightness and contrast that applies to the
standard of Video Preset.
When you adjust this value, it gives the same effect to dynamic and
mild of Video Preset.
The Standard Brightness can be differently adjusted depending on the
characteristics of the Panel.
That is, for the panel characteristics with luminance value that cannot
be adjusted with Panel Brightness, it means that the Standard
Brightness of Auto Picture can be adjusted.
For more detail, refer the pages 12, item (17) Panel Brightness.
(9) Running Time :
The System shows the accumulated operating time the Power is
turned On.
When Reset, it is reset to 0.

-11-

LGE Internal Use Only

(10) System All Reset :


It reboots itself after initializing not only the general NVRAM
Parameter but also Service Parameter.
(White Balance, YPbPr offset/gain, RGB offset/Gain etc.)
*** Therefore do not run System All Reset unless it is a special case.
If this item must be initialized, write down the adjusted value after
factory delivery of Panel brightness, Auto Picture, White Balance,
YPbPr offset/gain and RGB offset/Gain on paper then execute the
initialization.
Then after the execution, use the remote controller to re-enter the
written value without separate adjustment, and you can realize
the same TV quality.
(11) Audio Delay
Adjust the Audio Delay. The Group can be classified into 3 types.
- DTV Group
- ATV/CVBS/YC Group
- COMP/PC/HDMI Group
(12) AI Control :
This is the function to set ON/OFF to support the AI automatically in
the panel that supports the DCR(Dynamic Contrast Ratio) function.
*** The Default value is OFF and must be maintained at OFF without
separate notification.
(13) Last Power Save :
This is the item to set whether to save the Last Power.
(14) Panel Monitoring :
This is the item to set whether to use Panel Abnormal Detection
Monitoring.
(15) Panel ID :
This is the item to set the Panel ID.
You can set the Display ID, Panel Company ID and Model ID of the
Panel currently connected.
The Display ID is fixed to LCD and the Panel Company ID toggles
among LG, SAMSUNG and AUO.
When the Panel Company ID is decided, you must set the Model IT
accordingly.

Under the condition of HDMI 1080i Input, Video mode : Standard,


Color temperature : Normal.
Set the generator signal source to Grays11/1080i30/HDMI (H8C).
Change to the HDMI input mode, observe the TV display screen.
Adjust the PANEL BRIGHT item of the TV SERVICE MENU, to make
the measured Bright Value of the CA-210 should be 25(cd/m2) in the
2nd bars from Left side of the GRAYS11 pattern on the TV display
screen.
If you couldnt get the suitable Bright Value 25(cd/m 2), adjust the
AUTO BRIGHT of the AUTO PICTURE item on the Service menu.
(18) Epg Mode :
This is the item to set the condition of Epg.
It Toggles among Mini, Full and None.
(19) SW Upgrade :
This is the item to Upgrade the Software using the RF Stream.
Send the stream with the Upgrade program to the desired channel
using the generator and setup as follows.
- RF Mode (Air or Cable) selection : For the remote controller,
press left/right to select 0(Air) or 1(Cable).
- RF Freq : Select the channel number with the stream.
- FE Mode(VSB/64QAM/256QAM) : Use the left/right button of the
remote controller to select 0(VSB), 1(64QAM) or 2(256QAM).
But you must not set 64QAM/256QAM for Air.
After completing the all the settings, select upgrade start to start the
upgrade.
When all the upgrade is normally completed, the system will
automatically reboot. Even if it fails, you must turn the power off and
then turn it back on to return to its normal condition.
(20) EXIT
Exit the Service Menu.

(16) Commercial Flag :


This is the item to set whether to communicate with the Network
Board or operate Stand alone.
This must always be set to ON unless it is a special testing
environment.
(17) Panel Brightness :
This is the item to adjust the brightness of the panel.
The default set value is 70 and can be adjusted to between 1 and 100.
When the value is set to 1, it is the lowest value (20%) and when set to
100, it is the highest brightness (100%).
The PWM signal sent out from MICOM is converted to DC voltage to
adjust the brightness of the panel.
As a reference, the DC voltage value sent out from the board
according to the set value is as follows.

Set Point
1
10
20
30
40
50
60
70
80
90
100

Output DC Voltage(V)
0.210
0.345
0.520
0.715
0.945
1.215
1.530
1.850
2.200
2.630
3.170

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-12-

LGE Internal Use Only

7) Click on the Download File Browse button, select .mem file,


and click on the Open button.

2. Software Upgrade

2.1 Serial Upgrade


(1) DTV B/D Program Download
[Preparations]
Required equipment : PC, D-SUB 9pin Female to Female cross type
RS-232C cable
S/W : KMCOMM.exe

[Menu item description]


Exit : End the program.
Port : Setup the serial port for the Host to use. COM1~COM4
Connect : KMCOMM uses the host serial port setup in .
Model : Main chipset type setup to be used in TV.
(For this model it is SupraHD)
Data Type : Setup the S/W type of file to Download.
Speed : Increase the download speed up to twice Dynamically.
Download File Browse : Select the *.mem file to Download.
Download File Status : This indicates the files setup to currently
download.
Ready : Standby until the TV can communicate with KMCOMM.
Stop : Stop the standby for communication with the TV.
Download Progress : This indicates the progress of download
to the TV.
As the window to show you the download status in message,
you can see the progress status in detail.
[Executing order]
1) Unplug the power cord of the TV.
2) Set the RS-232C SELECT switch on the back of the TV in the
direction of NORMAL(DTV).
3) With the RS-232C Cable, connect the RS-232C port of the TV
and the COM port of the PC.
4) Execute the KMCOMM.exe program on the PC.
5) After checking the port number connected to the TV from
Control Panel System Hardware Device Manager
Ports, set the Port for the Connection group.
6) Check whether the Model of the Configuration group is set to
SupraHD, and the Data type to Application.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

8) Click on the Connect button of the Connection group, and


check whether the Ready button of the Operation group is
activated.
(At this time, check whether <Connect COM port success> is
shown in the Message window.)
9) Click on the Ready button of the Operation group.
10) Press the UPDATE button on the back of the TV and plug the
power cord.
11) When the Download Progress Bar becomes 100%, check whether
the Message window shows Close Serial Download Program,
And Please Power Off/On for apply new Application code and the
Ready button of the Operation group is activated. (Make sure the
power is not disconnected before the Download is complete.)

12) If there is no problem, end the KMCOMM.exe program and unplug


the power cord, and then plug the power cord to check whether it is
operating normally.

-13-

LGE Internal Use Only

(2) Control B/D Program Download

8) Check if the Hyper Terminal is connected.


Turn on the TV while pressing the UPDATE SWITCH on the
rear part of TV, and check the following menu screen.

[Executing order]
1) Check whether the TV is for lodging or Healthcare.
2) Unplug the power cord of the TV.
3) Set the RS-232C select switch on the back of the TV in the
direction of CONTROL.
4) With the RS-232C cable, connect the RS-232C port of the TV
and the COM port of the PC.
5) Execute Hyper Terminal program of PC and assign the Name and Icon.

9) Input a to execute the Erase Flash. When it displays the menu screen,
input b to execute the Program Flash.

6) After checking the port number connected to the TV from


Control Panel System Hardware Device Manager
Ports, set the Port for the Connect using.

7) Set 115200 for Bit per second, 8 for Data bits, None for Parity,
1 for Stop bits, None for Flow control, and then click on OK button.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

10) Click on the Transfer menu on the above and select Send text file.
Select the .s19 file to download and click on Open button.
(Check whether the TV is for lodging or Healthcare.)

-14-

LGE Internal Use Only

11) Check if the Downloading process is as following and wait


until it completes. (Make sure the power is not disconnected
before the download is complete.)

[Wiring diagram of EEPROM 24LC02 and RGB PC EDID Cable]

[Wiring diagram of EEPROM 24LC02 and HDMI EDID Cable]

12) When the downloading process is completed and it shows the


menu screen, turn off TV and then turn it on again.

[Data read of EEPROM using RGB PC port and HDMI port]


1) Connect the USB port of the PC and the UprogHS 48 Potable
using the USB Cable, and connect the UprogHS 48 Potable with
the TV using the HDMI and RGB PC EDID Cable.
2) Execute the UprogHS 48 Potable program.

13) Change the RS-232C SELECT Switch on the rear part of TV


into the NORMAL(DTV) and turn it off.
Turn it on again after 5 seconds.
14) Check the PTC Version from Service Menu of the TV.

(3) RF Upgrade
This is how to upgrade program in the TV set without any
separate equipment.
ATSC Stream generator sends the stream with the upgrade
program, and the SW Upgrade is selected from the service
menu of the TV to execute the setting.
- Select RF Mode(Air or Cable) : Press the left/right button on the
remote controller to select 0(Air) or 1(Cable).
- RF Freq : Select the channel number including the upgrade
program Stream.
- FE Mode(VSB/64QAM/256QAM) : Use the left/right button
of the remote controller to select 0(VSB), 1(64QAM) or 2(256QAM).
But you must not set 64QAM/256QAM for Air.

3) Click on the Device


button and select the 24LC02B/TSOP as
the Device.
4) Click on the Read button of the SINGLE TAB to read the Data of
EEPROM.
5) Proceed by clicking on the
button.
6) After checking the
, compare the Data Read
from EEPROM with the Default Data.
7) To save the Data in the BUFFER, click on the
button of Buffer
group, and then click on
button of the Save File window.
8) Save the file in .dat format and end the program.

After completing the all the settings, select upgrade start to


start the upgrade.
When all the upgrade is normally completed, the system will
automatically reboot. Even if it fails, you must turn the power
off and then turn it back on to return to its normal condition.

(4) EDID Data Write : RGB PC port, HDMI port EDID down load
(Read/Write)
Required equipment : PC, EEPROM Programmer(Ex : UprogHS 48
Potable), HDMI EDID Cable, RGB PC EDID
Cable
S/W : Ex)Uprog.exe

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-15-

LGE Internal Use Only

[Data Write of EEPROM using RGB PC port and HDMI port]


1) Connect the USB port of the PC and the UprogHS 48 Potable
using the USB Cable, and connect the UprogHS 48 Potable with
the TV using the HDMI and RGB PC EDID Cable.
2) Execute the UprogHS 48 Potable program.

[RGB PC EEPROM Default Data]


ADDRESS
00000000
00000010
00000020
00000030
00000040
00000050
00000060
00000070
00000080
00000090
000000A0
000000B0
000000C0
000000D0
000000E0
000000F0

0
00
00
0F
01
35
40
5A
00
FF
FF
FF
FF
FF
FF
FF
FF

1
FF
10
50
01
00
80
20
48
FF
FF
FF
FF
FF
FF
FF
FF

2
FF
01
54
01
C4
37
50
44
FF
FF
FF
FF
FF
FF
FF
FF

3
FF
03
AF
01
8E
00
0B
54
FF
FF
FF
FF
FF
FF
FF
FF

4
FF
08
EE
01
21
C4
00
56
FF
FF
FF
FF
FF
FF
FF
FF

5
FF
50
00
01
00
8E
0A
20
FF
FF
FF
FF
FF
FF
FF
FF

BUFFER (HEX)
6 7 8 9 A
FF 00 4E 64 01
2D 78 0E EE 91
31 59 45 59 61
1B 21 50 A0 51
00 18 0E 1F 00
21 00 00 1E 00
20 20 20 20 20
20 20 20 20 20
FF FF FF FF FF
FF FF FF FF FF
FF FF FF FF FF
FF FF FF FF FF
FF FF FF FF FF
FF FF FF FF FF
FF FF FF FF FF
FF FF FF FF FF

B
00
A3
59
00
80
00
20
20
FF
FF
FF
FF
FF
FF
FF
FF

C
01
54
01
1E
51
00
00
20
FF
FF
FF
FF
FF
FF
FF
FF

D
00
4C
01
30
00
FD
00
0A
FF
FF
FF
FF
FF
FF
FF
FF

E
00
99
01
48
1E
00
00
00
FF
FF
FF
FF
FF
FF
FF
FF

F
00
26
01
88
30
38
FC
37
FF
FF
FF
FF
FF
FF
FF
FF

BUFFER (HEX)
6 7 8 9 A
FF 00 4E 64 01
2D 78 0A EE 91
31 59 45 59 61
64 19 00 40 41
00 18 1B 21 50
21 00 00 18 00
20 20 20 20 20
20 20 20 20 20
84 03 07 26 09
0C 00 10 00 80
00 C4 8E 21 00
28 55 00 C4 8E
10 10 3E 96 00
F0 16 00 26 7C
80 51 00 1E 30
00 00 00 00 00

B
00
A3
59
00
A0
00
20
20
07
01
00
21
C4
43
40
00

C
01
54
01
26
51
00
00
20
07
1D
9E
00
8E
00
80
00

D
00
4C
01
30
00
FD
00
0A
15
80
01
00
21
C4
37
00

E
00
99
01
18
1E
00
00
01
07
18
1D
1E
00
8E
00
00

F
00
26
01
88
30
38
FC
E5
50
71
00
8C
00
21
C4
C6

[HDMI EEPROM Default Data]


ADDRESS
4) Click on the Device

button and select the 24LC02B/TSOP as

00000000
00000010
00000020
00000030
00000040
00000050
00000060
00000070
00000080
00000090
000000A0
000000B0
000000C0
000000D0
000000E0
000000F0

the device.
5) Click on the
button of Buffer group and open the .dat file
to Write on the EEPROM, and then click on
.
6) After clicking the PROGRAM Tab, click on
button to write on
EEPROM when the Erase, Blank check, Program and Verify
button are activated.
7) Proceed by clicking on the
button.
8) After checking the
end the program.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-16-

0
00
00
0F
01
36
48
55
00
02
83
1C
72
0A
18
00
8E

1
FF
10
50
01
00
88
20
48
03
01
16
51
D0
8C
00
21

2
FF
01
54
01
C4
35
50
44
1B
00
20
D0
8A
0A
98
00

3
FF
03
AF
01
8E
00
0B
54
F2
00
58
1E
20
A0
0E
00

4
FF
81
EE
01
21
C4
00
56
44
66
2C
20
E0
14
1F
1E

5
FF
50
00
01
00
8E
0A
20
85
03
25
6E
2D
51
00
00

LGE Internal Use Only

3. Commercial Interface Installers Menu Setting

3.1 Accessing the Installers Menu


Make sure TV is on. Installers menu items can be accessed by using an installers remote control.
Just press MENU repeatedly(at least 10 times) until the TV seems to stop responding, then press 9, 8, 7, 6, then ENTER.
To exit the Installers Menu, press ENTER again. Any changes you make will be stored in nonvolatile memory.(The menu also disappears automatically.)
The Installers menu opens with item 000 INSTALLER SEQ 000. Use the Up/Down arrow keys to sequence through the available menu items.
Or, access an item directly by keying in the line number, then pressing MENU. For example, to access the Sleep Timer option which is item 015,
press 0-1-5, then MENU. To change a setting, use the Left/Right arrow keys. Or, enter a value directly. Press ENTER to remove Installer menu display.
Typical Installer Menu
26LH1DC1-UB INSTALLER MENU
000 INSTALLER SEQ 000
UPN : 000-000-000-000 FPGA 09F1
PTC V1.00.000
CPU V1.25.00

3.2 Using the Installers Menu


Items 000 ~ 117 are immediately accessible only upon entering the Installers Menu.
Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below and on the following pages.
Installer Menu Items 000 through 117

Menu
Item

Function

Value
Range

Default
Value

000~3
000~7
000~1
000~3
000~127, 255
000~1
000~63, 255
000~63
000~63
000~1
000~1
000~1
000~1
000~1
000~1
000~99
000~1
000~1
000~1
000~1
020~169
186~227
000~1
000~1
000~1
000~1
000~1
001~7, 255
000~1
000~1
000~1
000~7
000~7

000
000
000
001
255
000
255
000
63
000
000
001
000
001
001
012
000
001
001
000
094
207
001
001
001
001
001
255
000
000
001
002
002

000
001
002
003
004
005
007
008
009
010
011
015
016
017
021
022
023
028
029
030
031
032
034
035
038
039
040
046
047
053
069
070
071

INSTALLER SEQ
POWER MANAGE
AC ON
BAND/AFC
STRT CHANNEL
CHAN LOCK
STRT VOLUME
MIN VOLUME
MAX VOLUME
MUTE DISABLE
KEY DEFEAT
SLEEP TIMER
EN TIMER
ALARM
V-CHIP
MAX BLK HRS
CAPTION LOCK
CH. OVERIDE
OLD OCV
ACK MASK
POLL RATE
TIMING PULSE
CAMPORT EN
CAMPPORT EN
YPrPb EN
REAR AUX EN
AUTO CAMPORT
STRT AUX SRCE
AUX STATUS
DIS. CH-TIME M.
EN. CH-T COL.
FOR. CH-TIME
BCK. CH-TIME

073

CH NOT AVBLE

000~1

000

075
078
079
080
081

REVERT CH
UPN MSB
UPN MSB-1
UPN MSB-2
UPN LSB

000~1
000~255
000~255
000~255
000~255

000
000
000
000
000

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

Brief Description of Function and Comments


Leave default set 0.
Sets number of hours of no activity before auto shut off.
Set to 1 to enable auto turn on at power up.
Selects Tuning band.
Channel at turn-on (Set 255 to return to last channel before power off).
If set to 1, cannot tune from current channel.
Sets Volume level at TV turn-on(Set 255 to retain last volume level).
Sets minimum allowable volume setting.
Sets maximum allowable volume setting.
Set to 1 to disable mute function.
Disables menu navigation keys on display panel.
Set to 1 to enable Sleep Timer.
Set to 1 to enable On/Off Timers.
Set to 1 to enable Alarm.
Set to 1 to enable V-Chip functions.
Sets number of V-Chip(Parental Control) blocking hours.
Set to 1 to retain caption setting at power off.
If set to 0, limits direct access to favorite channels.
Set to 1 to change M.P.I. operation to OCV.
If set to 1, changes M.P.I. for some OCV boxes.
Selects poll rate for M.P.I.
Sets baud rate for M.P.I.
Set to 1 to enable Video 2 input.
Enables plasma panel DVI input port, set to 1 for DTV or 2 for PC. Set 0 to disable.
Set to 1 to enable display panel Component 1 input jacks.
Set to 1 to enable display panel Video 1 input jack.
For CRT-type TVs. Default set to 1 to automatically switch to Camport.
Sets the starting AUX source.
Set to 1 for M.P.I. AUX source reported as channel number instead of Channel 0.
Set to 1 to disable Channel-Time display.
Set to 1 to enable custom color for the Channel-Time display.
Chooses custom foreground color for the Channel-Time display.
Chooses custom background color for the Channel-Time display.
If set to 1 and channel override is 0, "NOT AVAILABLE" message is Displayed when
directly accessing a channel not in the favorite channel list.
If set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel.
User programmable number, most significant byte.
User programmable number, most significant byte - 1.
User programmable number, most significant byte - 2.
User programmable number, least significant byte.

-17-

LGE Internal Use Only

082
083
084
087
088
090
091
092
093
094
096
101
102
103
104
106
107
116
117

CHKSUM ERROR
HANDSHK TIME
PERMANENT BLK
REAR RGB EN.
EN NOISE MUTE
KEY LOCK
YPrPb2 EN
RGB2 ENABLE
RJP AVAILABLE
SAP MENU EN
DEF. ASP. RATIO
IR BLASTER
ATSC BAND
ATSC TUNE MODE
START MINOR CH
ASP RATIO LOCK
BANNER
VIDEO MUTE EN
FACT DEFAULT

000~1
000~5
000~1
000~2
000~1
000~1
000~1
000~2
000~1
000~1
000~134
N/A
000~4
000~1
000~255
000~1
N/A
000~1
000~1

001
005
000
002
001
000
001
002
000
001
002
N/A
004
001
000
000
N/A
000
000

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

Enforces rigid M.P.I. checksum.


Relaxes M.P.I. timing to be compatible with PC based Windows controlled systems.
Removes block hours setting for Parental Control and make blocks permanent.
Enables RGB1 input, set to 1 for DTV, or 2 for PC. Set to 0 to disable.
If set to 1, mutes audio if no signal is present.
If set to 1, keyboard is locked out, IR is still functional.
Set to 1 to enable plasma Component 2 input jacks.
Enables RGB2 input, Set to 1 for DTV, or 2 for PC. Set to 0 to disable.
Set to 1 to enable.
Set to 0 to disable feature on Function menu. Set 1 to enable feature on Function menu.
Sets default aspect ratio at power up. See detailed descriptions and item 106.
Not applicable.
Selects ATSC band.
Sets ATSC tuning mode. Set to 0 for virtual channel, set to 1 for physical channel.
Selects Minor start channel. Set 0 for NTSC. Not 0, sets Minor channel number.
Retains set aspect ratio on power cycle. Set to 0 for default ratio on power cycle.
Not applicable.
Set to 0 for normal, set to 1 for Blank.
0=Normal. 1=Loads presets of all above settings.

-18-

LGE Internal Use Only

4. Shipment Condition : Product & Customer Menu Setup


No.

General Item

Default Condition

1
2
3
4

RS232C Select
Input mode
Volume Level
Mute

Leave default set 0.


TV02CH
20
Off

No.
1

User OSD Menu Item

Default Condition

Picture

Mode

Standard

Sound

Color Temperature
Screen Format
Noise Reduction
Film Mode
Mode

Cool
16:9
Off
Off
Standard

Balance
(Digital Output)
Auto Volume
Multi-Track
Internal Speaker
(Antenna)
Auto Memorizing
Channel Label
Channel List
Fine Tune
Signal Strength
Time

Channel

Setup

V-Chip

Off
Stereo
On
(Only Item display)
Yes
Default
Empty
Auto
(DTV Only)
Clock
(Manual Clock)
Daylight Saving
Time Zone
(On Timer)
(Off Timer)
Auto Off
Please Enter your PIN.

Contrast
Brightness
Sharpness
Color
Tint

91
80
54
68
0(Center)

Treble
Bass

0(Center)
0(Center)

Manual
Yes
Eastern
(Only Item display)
(Only Item display)
Off
0000(Default)

Changing PIN
On/Off
TVPG Rating
MPAA Rating
Can. English Rating
Can. French Rating

Caption

(PC)
Menu Language
Menu Transparency
Set ID
On/Off
(Analog Mode)
(Digital Mode)
(Digital Font Option)

New PIN
Confirm PIN
Off
(Only Item display)
(Only Item display)
(Only Item display)
(Only Item display)

(Only RGB PC Input)


English
Semi Opaque
1
Off

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-19-

LGE Internal Use Only

5. Shipment Condition : Service Menu Setup


No.

Service Menu Item

Default Condition

1
2

System Reset
Software Version

Chip I2C Test

4
5

Aging Test
White Balance

YPbPr : offset/gain

RGB : offset/gain

Auto Picture

Running Time

10
11

System All Reset


Audio Delay

12
13
14
15
16
17
18
19
20
21
22

AI Control
Last Power Save
Panel Monitoring
Panel ID - Display ID
Panel Company ID
Model ID
Reserved
Commercial Flag
Panel Brightness
Epg Mode
SW Upgrade

Confirm
DM-327KA Aug 02 2006 V1.24 SUB V3.2
Display ID : 0(LCD)
Panel Company ID : 0(LG)
Model ID : 22(LG_LC260WX2_SL02)
HW ID : 0
Memory : OK
FLASH : OK
EEPROM : OK
TUNER : OK
VIDEO ADC : OK
AUDIO DEC : OK
Uart1 Comm. : NOT OK
Pillow Mode : 0
Uart Mode : 0
(Enter)
Offset R
Offset G
Offset B
Gain R
Gain G
Gain B
Reset Mode
Offset Y
Offset Pb
Offset Pr
Gain Y
Gain Pb
Gain Pr
Reset Mode
Offset R
Offset G
Offset B
Gain R
Gain G
Gain B
Reset Mode
Auto Brightness
Auto Contrast
Running Time
Reset Mode
Confirm
DTV
ATV/CVBS/YC
COMP/PC/HDMI
OFF
ON
OFF
Display ID : 0(LCD)
Panel Company ID : 0(LG)
Model ID : 22(LG_LC260WX2_SL02)

23

EXIT

ON
ADJ Value(70)
Mini
RF Mode
RF Freq
FE Mode
Upgrade Start
(Enter)

50
50
50
ADJ Value(50)
ADJ Value(50)
ADJ Value(50)
24
51
51
60
60
60
128
128
128
ADJ Value(128)
ADJ Value(128)
ADJ Value(128)
ADJ Value(50)
91
* HOURS

0
0
0

0(Air)
20
0(Vsb)

6. Shipment Condition : Installer Menu Setup


(See 3. Commercial Interface Installers Menu Setting page.)

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-20-

LGE Internal Use Only

SVC REMOCON
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38

KEY

FUNTION

REAMARK

To turn the TV on or off.


POWER
To turn the TV on automatically if the power is supplied to the TV. (Use the
POWER ON
POWER key to deactivate) : It should be deactivated when delivered.
To activate the mute function.
MUTE
N/A
P-CHECK
N/A
S-CHECK
To select size of the main screen. (Normal, Spectacle, Wide or Zoom)
ARC
Switch to closed caption broadcasting.
CAPTION
N/A
TXT
To select an external input for the TV screen.
TV/AV
N/A
TURBO SOUND
TURBO PICTURE N/A
To enter adjustment mode when manufacturing the TV sets.
IN-START
W/B adjustment. (automatic)
To enter into the adjustment mode.
ADJ
To select the multiple sound mode. (Mono, Stereo or Foreign language)
MPX
To release the adjustment mode.
EXIT
To easily adjust the screen according to surrounding brightness.
APC(PSM)
To easily adjust sound according to the program type.
ASC(SSM)
To check component input.
MULTIMIDIA
To check the front AV.
FRONT-AV
To move channel up/down or to select a function displayed on the screen.
CH
To adjust the volume or accurately control a specific function.
VOL
To set a specific function or complete setting.
ENTER
N/A
PIP CH-(OP1)
N/A
PIP CH+(OP2)
PIP SWAP(OP3) N/A
PIP INPUT(OP4) N/A
N/A
EYE
To select the functions such as picture, sound, channel, setup, caption.
MENU
To set the delivery condition status after manufacturing the TV set.
IN-STOP
To halt the main screen in the nomal mode.
STILL
N/A
TIME
N/A
SIZE
N/A
MULTI PIP
N/A
POSITION
N/A
MODE
N/A
PIP
N/A
TILT
To manually select the channel.
0~9

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-21-

Shortcut keys
Shortcut keys
Shortcut keys

Shortcut keys
Shortcut keys

Shortcut keys

LGE Internal Use Only

TROUBLE SHOOTING GUIDES

Check for problems


in Main Board
YES

Main Board
LED ON?

NO

Power Cable(13 PIN)


Check / Replace

NO

Front Cable(7 PIN)


Check / Replace

YES

NO

YES

SMPS
Check / Replace

NO

YES

Main Board
Replace
YES

YES

Is it communicating
with the Service Port?

NO

PC Serial port
Check the setting

NO

Serial Cable
Check / Replace

YES

YES

NO

MICOM
Check the operation
YES

NO

Main Board
Replace
YES

YES

Is the screen
color normal?

NO

LVDS Cable
Check / Replace

NO

Main Board
Replace

YES

YES

YES

Is the color normal


when External Input/
S-Video/Component
is selected?

NO

External equipment/
Cable Check / Replace

NO

Main Board
Replace

YES

YES

YES

Is the color normal


when PC/HDMI
is selected?

NO

External equipment/
Cable Check / Replace

NO

Main Board
Replace

YES

YES

YES

Is the left/right audio


output normal?

NO

Speaker Cable
Check / Replace

NO

Check for problems


in audio

YES

YES

YES

Normal operation

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-22-

LGE Internal Use Only

1. Check if the SMPS power is connected to the Main board and stand-by power connected, and whether green light is on for LED(D101).
If the green light is not on, check the stand-by power(5V).
2. Turn ON the POWER using the remote controller or the front key button.
At this time, check whether the green light is on for LED (D102).
If the green light is not on, measure the next power with DMM.
- Pin no. 3, 4 and 5 of CN101 (D12V)
- Input/output voltage of IC503 (D12V, D6V)
- Input/output voltage of IC710 (D6V, A5V)
3. Check whether the LCD panel is operating normally.
If the display is not working normally, check the LVDS cable and take the following actions.
- Check the input/output voltage of IC501. (D12V, D3.3V)
- Check the input/output voltage of IC704. (D3.3V, D2.5V)
- Check the input/output voltage of IC714. (D3.3V, D1.8V)
- Connect the UART Cable to the Service Port and activate the debugger window of the PC.
After connecting the power to the Main board, check whether the booting flow is normally written in the debugger window of the PC.
(To enable communications with the PC, always use the UART cable checked for normal operation.)
- If the booting flow is not written at all in the debugger window of the PC, check the power(D3.3V, D2.5V, D1.8V) connected to the main chip(IC401).
And then if there is no problem with the power, check the connection pattern condition of the main chip(IC401) and the Flash memory(IC403),
and check the cold solder or short circuit of each pin of the flash memory.
- If only 1 line of booting flow is written in the debugger window of the PC and nothing after that, check the power(D3.3V, D2.5V, D1.8V) connected
to the main chip(IC401).
And if there is no problem with the power, check the cold solder or short circuit of the array resistance(RA403-RA416) connected to the main chip
and DDR memory(IC402 and IC404).
Check the cold solder or short circuit of each pin of the DDR memory.
- When the booting flow is normally written in the debugger window of the PC but rebooting, check the communications line(SCL1, SDA1) of MICOM
(IC705) and main chip(IC401).
4. Check whether the digital broadcasting is normally received. If it is not normally received, check the following.
- Measure the power of no. 3 pin of TUNER(IC105). (TU5V)
- Measure the power of no. 12 pin of TUNER(IC105). (TU3.3V)
- Measure the power of no. 15 pin of TUNER(IC105). (TU1.8V)
- Check the cold solder and short circuit etc. of the serial resistance(RA101, RA102) and other resistances(R114~R116) of the TS Data line.
- Check the communications line(SCL0, SDA0).
5. If the digital broadcasting is normally received but the analog broadcasting is not received normally, check the no.16 pin of IC706(74VHC4051).
(CVB_5V) For a more detail review, check the signal wave form of Q106, Q101, Q104 etc. with the oscilloscope.
6. Check if the external input of AV1, 2, 3, S-Video etc. If the video does not show well, check whether there is any problem with IC706, which is the analog
video switch.
If a specific external input does not work, check the external input device and check whether there is any problem with the cable.
If not identified simply, check for problems following the signal of Video/audio signal flow chart.
7. Check the external input of Component1 and 2.
If the video of the Component does not work at all, check if there is any problem in IC202, the component video switch and IC201, AD converter.
If a specific external input does not work, check the external input device and check whether there is any problem with the cable.
If not identified simply, check for problems following the signal of Video/audio signal flow chart.
8. Check the PC input and HDMI(DVI) input.
If the PC video does not work, check whether there is any problem with the connection cable.
If the HDMI video does not work or only the video works without any audio, rewrite the EDID data.
9. Check if the left/right side of the audio working normally.
Check the cold solder and short circuit of IC708(STA323W) when the audio does not work.
For analog broadcasting, check the cold solder and short circuit of IC602(MSP3425) since it goes through this.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-23-

LGE Internal Use Only

TROUBLE SHOOTING
1. No Screen(1)
Symptom
Front LED is on as green color, but no picture.
Check Flow
Check LVDS Cable?

NO

Is the LVDS cable connected well?

NO

Reset Cable

YES

YES

Check Power On signal?

Replace LVDS Cable

NO

Is the Power On Signal correct?

NO

Check Key Pad/IR Input

YES

YES

Is LCD Voltage +24V/+12V


normal?

Check Power Supply

NO

Check Power Supply

YES

Video Normal on Analog RF?

NO

Check TUNER

YES

Video normal on Video3?

NO

Check HC4051

YES

Video normal on DIGITAL RF?

NO

Check TUNER

YES
Video normal on
AutoCamport/AV2

NO

Check HC4051

YES

Check RJP Mode

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-24-

LGE Internal Use Only

2. No Screen(2)
Symptom
Front LED is blinking as green color, and no picture.
Check Flow
NO

Check LVDS Cable?

Is the LVDS cable connected well?

NO

Reset Cable

YES

YES

Replace LVDS Cable

NO

Is LED, D102 lighted?

Check Key Pad/IR Input?

NO

Replace Key Pad or IR Input

YES

YES

Check the Main Board

Check Power Supply

3. No Power
Symptom
Front LED is OFF, and no picture.
Check Flow
Power cord connected?

NO

Plug in Power cord.

YES

Is Fuse(F101) on Power Board good?

NO

Replace Fuse(T5.0A H 250V)

YES

Is the Power Board connected to


each control Board?

NO

Connect cable

YES
When ST-BY 12V/5V does not operate,
replace Power Board.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-25-

LGE Internal Use Only

4. No Sound
Symptom
Front LED is ON as green color, but no sound.
Check Flow
Check Speaker Cable?

NO

Is the SPK cable connected well?

NO

Reset Cable

YES

YES

Audio Voltage +12V normal?

Replace Speaker Cable

NO

Check Power Supply

YES

Audio normal on HDMI?

YES
NO

Audio normal on DIGITAL RF?

NO

Check STA323W

YES

YES

Audio normal on Analog RF?

Check EDID EEPROM

NO

Check MSP3425

YES

Audio normal on Video3?

NO

Check TEA6422D

YES

Audio normal on DIGITAL RF?

NO

Check TUNER

YES
Audio normal on
AutoCamport/AV2

NO

Check TEA6422D

YES

Check RJP Mode

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-26-

LGE Internal Use Only

BLOCK DIAGRAM
Model : 26LH1DC1-UB

MPI
CARD

ST12V

MPI
NETWORK

ISOLATED
DC/DC CONVERTER
12VDC OUT

REMOTE
CONTROL

ST12V
+5V
REGULATOR

Digital Pillow
Speaker

ISOLATED
SERIAL DATA
INTERFACE
ISOLATED
OUTPUT TRANSFORMER
8 OHM/2W

7.3728 MHz

Speaker
Switch
MPU
(MC9S12W128CFU)
SPEAKER
SELECTOR

VIDEO IN

Internal
Speaker

Auto camport
Audio R/L

RS232C
DRIVER

Service Port

RX/TX

IC

DATA
SELECTOR

FRAM

SPEAKER OUT

AUX CONTROL
IR-LED
DRIVER

RS232 Port
Switch

IR IN

C-BOX
Update Key

DDR
K4H561638

Flash

EEPROM

24MHz

26" (1366 X 768)

RX/TX
HDMI
RGB
24Bit

IC401
ZR39660

IC201
MST9883

ANTENNA
CABLE
CATV
NETWORK

IC707
BA7657

IC105
TDVS-H062P

MPEG2 TS
CVBS
Y/C
2
IC

Optical
8MHz

Caption

IC705
M37151

SPEAKER OUT

CVBS
IC706
74VHC4051

CVBS x 2

24.576MHz

SPDIF

Decryption
Block

Component
x2

LVDS Out

IR/Key

IC302
RTD2023B

RGB

IC708
STA323W

IC
S-Video
SIF
18.432MHz
Audio In
x5

IC601
TEA6422

IC602
MSP3425
12VA

Built-in Power Supply

12V ST12V ST5V

24V

AC IN
100~240VAC 50/60Hz

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-27-

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

POWER SUPPLY

AC IN
100~240V

DC +400V
MAIN
TRANS
(T801)

LINE
FILTER

RECTIFIER
(SCHOTTKY)

+24V/4.5A
A+12V/2.0A

MAIN
CONTROL
(IC802)

+12V/2.5A
FEED
BACK
(IC804)

-28-

BRIDGE
(BD801)

PSU
PWR ON/OFF
(Q803)

OPTO
COUPLER
(IC807)

STAND-BY
TRANS

ACTIVE HIGH

RECTIFIER
(SCHOTTKY)

PWR-CTL

ST +12V/1.25A

(T901)
PFC
(IC801)

5V REGULATOR
(U201)
STAND-BY
CONTROL
(IC900)

FEED
BACK
(IC902)

ST +5V/0.1A

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

Power Tree
24V
12VA

2.8 ~ 3.65A

LCD_24V

0.6 ~ 1.8A

AMP_12V
FDS4435

12V

0.06A

LCD_12V

0.5A

KA7809

55mA

DC/DC

D6V

A9V
KA7805

165mA

0.35A

A3.3V

AME1117

TU3.3V

AME8802

-29-

KA7805
0.2A

DC/DC

3.3V 0.36A

A5V

0.24A

TU5V
TU1.8V

AME8807

LCD Panel : 3.15A(INVERTER)


STA323W : 2A
LCD Panel : 450mA( Logic )
MSP3425 : 40mA, TEA6422 : 10mA
MC33078 : 10mA
MSP3425, 74HC4051, FMS6143, TS5V330D
RTD2023B : 50mA
MST9883 : 100mA
Tuner : 10mA
Tuner : 225mA
Tuner : 340mA

SMPS
0.3A

0.19A

AME8815

0.18A

LGE Internal Use Only

ST5V
ST12V

D2.5V

HD660 : 50mA
K4H281638D x 2 : 300mA

A1.8V

AME1117
SC1566

D3.3V

HD660 : 300mA, STA323W


AM29LV320 : 50mA
MST9883 : 100mA
RTD2023B : 230mA
W24C256, SP3232 : 30mA

1.2A

1.8V

0.1A
0.1A

RTD2023B : 80mA
HD660 : 1.1A
RTD2023B : 80mA
M37151

78M05

0.1A

5V

MC9S12E128CFU

SupraHD-660 IC Block Diagram


Note : The SupraHD-680 has an integrated CableCard controller, the SupraHD-660 does not.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-30-

LGE Internal Use Only

SupraHD-660/680 Overview
1. SupraHD ZR396x0 Family
The ZR396xx family consists of :
SupraHD-680 IC (ZR39680) - Digital TVs for the ATSC/DVB/OpenCable Market
SupraHD-660 IC (ZR39660) - Digital TVs for the ATSC Market
SupraHD-640 IC (ZR39640) - Digital ATSC upgrade for Analog TVs
2. SupraHD-660/680 IC Description
The SupraHD-660/680 ICs are members of the SupraHD family of DTV controllers developed by Zoran.
These devices are intended to be used in ATSC-compliant television implementations.
They add the functionality required to support OpenCable implementations.
These devices include all of the functionality required to support the television implementations shown in the following system
block diagrams.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-31-

LGE Internal Use Only

Figure 3 shows a typical system implementation using the SupraHD-660/680. This system can be designed and manufactured in a
very low-cost manner.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-32-

LGE Internal Use Only

3. I/O Options
Figure 4 shows the four major I/O options available :
video input and output
audio input and output

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-33-

LGE Internal Use Only

VIDEO AND AUDIO SIGNAL FLOW CHART


1. Digital RF(ATSC, QAM) Video signal flow chart

IC105
TUNER

RF Signal Input
(ATSC/QAM)

TS Data

IC901
ALTERA FPGA

Unscrambled
TS Data

IC401
DTV Controller

LVDS Signal

P503
LVDS Connector

LCD Panel

*Tuner(ATSC/QAM) Video signal flowchart

The digital RF signal(ATSC/QAM) received in the input terminal of the tuner is converted to the base band signal in
the tuner(IC105) to send out 8 bit transport stream.
This signal is transferred to the FPGA chip of IC901. FPGA chip decrypts the TS data so that it can be decoded by
the DTV decoder in the next terminal.
The TS data decrypted by IC901 is decoded by the video decoder of DTV controller of IC401 and converted to the
LVDS signal.
The LVDS signal is transferred to the LCD panel through the P503 connector to be displayed on the LCD panel.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-34-

LGE Internal Use Only

2. Digital RF(ATSC, QAM) Audio signal flow chart

IC105
TUNER

RF Signal Input
(ATSC/QAM)

TS Data

IC901
ALTERA FPGA

Unscrambled
TS Data

IC401
DTV Controller

IEC958

P501
SPDIF Output
Connector

I2S

IC708
Digital Audio Amp.

Stereo(L/R)

P706, P707
Audio Output
Connector

Speaker

*Tuner(ATSC/QAM) Audio signal flowchart

The digital RF signal(ATSC/QAM) received in the input terminal of the tuner is converted to the base band signal in
the tuner(IC105) to send out 8 bit transport stream.
This signal includes both the video and audio signal. The audio received by the DTV controller through IC901 is
decoded for Dolby AC3 in the audio decoder and the PCM data is transferred in I2S format.
This signal is converted to stereo signal(L/R) from the digital audio amp(IC708) and then sent to the internal speaker
through audio output connector(P706, P707).
Also for the digital audio data in IC401, the PCM or AC3 compressed data by user setting is sent out in SPDIF
format through P501.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-35-

LGE Internal Use Only

3. Analog RF(NTSC) Video signal flow chart

IC105
TUNER

RF Signal Input
(NTSC)

TU_CVBS

IC706
Analog MUX
(Video switch)

CVBS
for Caption

IC107
SD Video Filter

CVBS

IC401
DTV Controller

I2C Comm.

IC705
Micro Processor

LVDS Signal

P503
LVDS Connector

LCD Panel

*Tuner(NTSC) Video signal flowchart

The analog RF signal(NTSC) received in the input terminal of the tuner is converted to the base band signal in the
tuner(IC105) to send out the composite signal.
This CVBS signal is received by IC706 which is the analog video switch. The analog video switch receives the
CVBS signal sent from the tuner and the external signal, AV1, AV2, AV3, S-Video caption and Component caption
signal and sends out one of the signals.
The external input mode selected by the TV/AV button on the remote controller is the video signal selected for output.
The output signal is the decoded in the DTV controller of IC401 and converted to LVDS signal to be sent to the
LCD panel through the LVDS connector of P503.
Also the output signal from the analog video switch of IC706 is used as the caption signal.
This signal is amplified 2 times to send to the microprocessor(IC705), and IC705 arranges the caption signal to send
the caption information to the DTV controller through the I2C communications line.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-36-

LGE Internal Use Only

4. Analog RF(NTSC) Audio signal flow chart

IC105
TUNER

RF Signal Input
(NTSC)

SIF

IC602
Audio Processor

IC603
OP Amp.

I2S

IC401
DTV Controller

IEC958

P501
SPDIF Output
Connector

I2S

IC708
Digital Audio Amp.

Stereo(L/R)

P706, P707
Audio Output
Connector

Speaker

*Tuner(NTSC) Audio signal flowchart

The audio signal of the analog RF signal(NTSC) received in the input terminal of the tuner(IC105) is sent out as the
sound IF signal by the tuner.
The SIF signal goes through Automatic Volume Correction(AVC) in the audio processor and sent to the
OP Amp(IC603).
This signal is amplified to be sent to the audio processor again.
The audio processor converts the stereo signal into I2S format to send to DTV controller and PCM data is outputted
in I2S format through audio decoding process.
This signal is converted to the stereo signal(L/R) in the digital audio amp(IC708) to be sent to the internal speaker
through the audio output connector(P706, P707).
Also the digital audio data in IC401 outputs the PCM data in SPDIF format through P501.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-37-

LGE Internal Use Only

5. AV1, AV2, AV3 Video signal flow chart

AV2 Input

AV1, AV3 Input

P703
RCA Jack

CN105
Wafer

CVBS

IC706
Analog MUX
(Video switch)

CVBS
for Caption

IC107
SD Video Filter

CVBS

IC401
DTV Controller

I2C Comm.

IC705
Micro Processor

LVDS Signal

P503
LVDS Connector

LCD Panel

*Composite(AV1, 2, 3) Video signal flowchart

External input AV1 and AV3 are received through the RCA jack of P703, and AV2 is received through the 6 pin
wafer of CN105.
These signals all come to the analog video switch(IC706) and only 1 signal is selected. In other words, it is the same
as the analog RF signal.
The one signal that has been selected for output is decoded in the DTV controller and converted to LVDS signal to
be sent to the LCD panel through the LVSD connector(P503).
Also the output signal from the analog video switch is used for caption.
The signal received from IC107 is filtered and amplified 2 times to be received by the microprocessor.
The microprocessor analyzes(caption slicing) this signal to send the caption information.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-38-

LGE Internal Use Only

6. AV1, AV2, AV3 Audio signal flow chart

AV2 Input

AV1, AV3
(S-Video) Input

P703
RCA Jack

CN105
Wafer

IC601
Audio Switch

IC602
Audio Processor

I2S

IC401
DTV Controller

IEC958

P501
SPDIF Output
Connector

I2S

IC708
Digital Audio Amp.

Stereo(L/R)

P706, P707
Audio Output
Connector

Speaker

*Composite(AV1, 2, 3(S-Video)) Audio signal flowchart


The left/right audio signal of AV1, AV2 and AV3(S-Video) is received by P703 and CN105, and the AV3 uses the
same audio terminal as S-Video.
One stereo signal among the signals received through the audio switch(IC601) to send to the audio process(IC602).
The Audio switch receives the audio input signal of AV1, AV2, AV3(S-Video) and component1, component2,
PC(DVI) to select and output one stereo signal.
The stereo signal selected this way is converted to I2S format in the audio processor to send to DTV controller for
output I2S format through audio decoding process.
This signal is converted to stereo signal (L/R) in the digital audio amp(IC708) to send to the internal speaker through
audio output connector(P706, P707).
Also the digital audio data in IC401 is outputted as PCM data in SPDIF format through P501.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-39-

LGE Internal Use Only

7. S-Video Video signal flow chart

P101
S-Video Jack

S-Video Input

CVBS
for Caption

S-Video

IC401
DTV Controller

IC706
Analog MUX
(Video switch)

IC107
SD Video Filter

I2C Comm.

IC705
Micro Processor

LVDS Signal

P503
LVDS Connector

LCD Panel

*S-Video signal flowchart


S-Video signal is received through P101 jack.
Y signal and C signal are separated in this signal and is received directly by DTV controller(IC401) and decoded by
IC401 to convert to LVDS signal.
Then it is sent to the LCD panel through P503.
And the caption signal is send to IC401 through the video filter (IC107) and microprocessor(IC705) via analog video
switch(IC706).
The audio signal of S-Video is used as the audio signal of AV3.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-40-

LGE Internal Use Only

8. Component1, Component2 Video signal flow chart

Component1
Component2
Input

P201
RCA Jack

Y/Pb/Pr

IC202
Video switch

Y
for Caption

IC706
Analog MUX
(Video switch)

IC701
SD Video Filter

IC201
AD Converter

Y/Cb/Cr
24 bit Digital signal

IC401
DTV Controller

I2C Comm.

IC705
Micro Processor

LVDS Signal

P503
LVDS Connector

LCD Panel

*Component1, 2 Video signal flowchart

One of the component1 and 2 video signals received in P201 is selected by the video switch(IC202) and sent to
Analog to Digital converter(IC201).
The analog signal received in IC201 is converted to the digital signal and sent as output in 24 bit.
The digital signal of 24bit is received in DTV controller(IC401) and decoded to convert to LVDS signal and sent to
the LCD panel through LVDS connector.
Also because the caption information in the component signal received in IC202 is in Y signal, the Y signal is sent to
the analog video switch of IC706 to be sent to IC401 through IC107 and IC705.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-41-

LGE Internal Use Only

9. Component1, Component2 Audio signal flow chart

Component1
Component2
Input

P601
RCA Jack

IC601
Audio Switch

IC602
Audio Processor

I2S

IC401
DTV Controller

IEC958

P501
SPDIF Output
Connector

I2S

IC708
Digital Audio Amp.

Stereo(L/R)

P706, P707
Audio Output
Connector

Speaker

*Component1, 2 Audio signal flowchart


The left/right audio signal of component1 and component2 is received in P601 and sent to the audio switch(IC601).
One stereo signal is selected among the received signals in the audio switch(IC601) and sent to the audio
process(IC602).
The stereo signal selected is converted to I2S format through the audio processor and sent to the DTV controller to
be sent as output in I2S format through the audio decoding process.
This signal is converted to stereo signal(L/R) by the digital audio amp(IC708) and sent to the internal speaker
through the audio output connector(P706, P707).
Also the digital audio data in IC401 is sent as output, PCM data, through P501 through SPDIF format.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-42-

LGE Internal Use Only

10. PC Video signal flow chart

RGB Signal Input

P301
D-sub 15 Connector

I2C Comm.

IC303
NVRAM
(PC EDID)

R/G/B

IC302
Scaler

24bit
Digital signal

IC401
DTV Controller

LVDS Signal

P503
LVDS Connector

LCD Panel

*PC RGB signal flowchart


The RGB signal outputted from the PC is received through the D-sub 15 pin connector of P301.
The PC reads the EDID information of IC303 through I2C line and outputs the best resolution supported by this board.
When the EDID information is not recorded in NVRAM(IC303) or when the EDID information cannot be read due to
communications line issue, basic resolution provided in PC is sent out as output.
The analog RGB signal entered through IC302 is converted to AD through the scaler(IC302) and sent to IC401 as
24 bit digital signal.
(The 24 bit signal is composed is wired OR with the 24 bit component outputted by the IC201(AD converter).)
The 24 bit signal received in DTV controller(IC401) is decoded and converted to LVDS to be sent to LCD panel
through P503.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-43-

LGE Internal Use Only

11. PC(DVI) Audio signal flow chart

P602
Phone Jack

PC(DVI)
Input

IC601
Audio Switch

IC602
Audio Processor

I2S

IC401
DTV Controller

IEC958

P501
SPDIF Output
Connector

I2S

IC708
Digital Audio Amp.

Stereo(L/R)

P706, P707
Audio Output
Connector

Speaker

*PC(DVI) Audio signal flowchart


PC audio signal or DVI audio signal is received in P602 to be sent to the audio switch(IC601).
One stereo signal among the signal received by the audio switch(IC601) is selected and sent to the audio
process(IC602).
Selected stereo signal is converted to I2S format by audio processor to be sent to DTV controller and outputted in
I2S format through audio decoding process.
This signal is converted to stereo signal(L/R) by digital audio amp(IC708) and sent to the internal speaker through
audio output connector(P706, P707).
Also the digital audio data in IC401 is outputted as PCM data in SPDIF format through P501.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-44-

LGE Internal Use Only

12. HDMI(DVI) signal flow chart

P505
HDMI Connector

HDMI(DVI)
Signal Input

I2C Comm.

IC504
NVRAM
(HDMI EDID)

TMDS Signal

IC401
DTV Controller

LVDS Signal

P503
LVDS Connector

LCD Panel

*HDMI(DVI) Video signal flowchart

HDMI transmitter reads the HDCP certification and EDID information when connected to the HDMI connector (P505).
At this time, if the HDCP certification fails or if the EDID information cannot be read, the HDMI transmitter does not
send out the video and audio signal.
When HDCP certification is successfully done, the signal sent by the transmitter that could not read the
EDID information is decoded by the DTV controller(IC401) and converted to LVDS signal to be sent to the
LCD panel through the LVDS connector.
The DVI transmitter only outputs the video signal after HDCP certification and reading the EDID information.
(For DVI transmitter, the PC generally outputs the video signal after HDCP certification and reading
the EDID information, but if the Set Top Box is the DVI transmitter, sometimes it outputs only the video signal
unconditionally in set resolution.)
The signal received through IC401 is shown in the display through the same process as above.

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-45-

LGE Internal Use Only

[26LH1DC1-UB]

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

WIRING DIAGRAM

-46-

LGE Internal Use Only

WIRING DIAGRAM FOR 26LH1DC1-UB

MODEL NO. : 26LH1DC1-UB

10

9
7

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

EXPLODED VIEW

20

-47-

19
18
1

16

17

14

15

12
11

LGE Internal Use Only

13

EXPLODED VIEW PARTS LIST

NO.

PART NO.

ABJ36972701

Cover_Front (Silver) Assembly

PART NAME

DESCRIPTION

EAJ40492101

26" LCD Panel, LC260WX2-SLB2

ADV36972501

Chassis_Main Assembly

EBU39110201

Power Supply Assembly, Built In, Free Volt

EBU39136401

PPV/DPS Main Board

MAZ42732101

Chassis_Supporter Wall

MGJ42733001

Cover_Rear AV Assembly

Cover_Rear AV+Gasket_EMI

EBU39136601

Digital Pillow Speaker Board Assembly

Digital Pillow Speaker Board+Harness

MGJ42732301

Chassis_Main Shield

10

ACQ36972801

Cover_Back Assembly

11

MBG42732401

Cover_Key Knob

12

EBU39111101

Key Board

13

MES42732701

Indicator_Led Lens

14

EBU39111301

IR Board

15

EBU39138801

Speaker_2p, 26_R_Assembly

Speaker+Harness

Speaker_3p, 26_L_Assembly

Speaker+Harness

MPI Card Assembly

Chassis_PCB Supporter + Chassis_PCB Guide + Cover_MPI Card +

Cover_Front (Silver)+Membrane_Key

Chassis_Main+Gasket_EMI+CR Sponge

Cover_Back + Plate_Rear AV + Label_Serial + Label_Dolby +


Label_ID/Spec

16

EBU38606701

Plate_MPI Card + Nut_Stamped_Locking + MPI Card Board(204-346000) + MPI Connector Board(6367T_MCN)


17

EBU39138901

Main Board Assembly

Main Board+Gap Pad+Gasket_EMI

18

EBU39115101

Service Board Assembly

Service Board+Gasket_EMI+Harness

19

EBU39115901

Auxiliary A/V In Board

20

MAZ42732601

Cover_Side Jack

ETC

EBU39117501

30PX30P(300mm) LVDS Cable

EBU39139001

Harness Assembly

Acce

EBU39139101

Installa tion&Setup Guide

ssory

EBU38690001

Hospital Power Cord_SJP_3P_1800mm

MAY42732801

Box

MFZ42732901

Packing

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

Cover_Side Jack+Plate_Side AV

-48-

LGE Internal Use Only

REPLACEMENT PARTS LIST

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-49-

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-50-

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-51-

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-52-

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-53-

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-54-

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-55-

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-56-

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-57-

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

-58-

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Copyright2007 LG Electronics. Inc. All right reserved.


Only for training and service purposes

LGE Internal Use Only

Internal Use Only


website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html

LCD TV
SERVICE MANUAL
MODELS : 26LH1DC1-UB
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : 3350GDKM0020A

December, 2007

You might also like