Matchless Motorcycles

This scan is explicit for non-commercial u
MAINTENANCE
SERIES
General Editor
BERNAL OSBORNE
of Motor Cycling
MATCHLESS
MOTORCYCLES 1939-55
SINGLE-CYLINDER 347 c_c. and 498 c.c.
and
EX-W.D. 347 C.c. MODELS
First published 1958
TEMPLE PRESS LIMITED. 1958
A maker's definitive photograph by courtesy of Motorcycfe Sport for the 1953 500 cc Matchless, G80C shown herein trlsls 9uWe with
lk./htiJlfoy motor, pre-Monobloc c8rburetter, rigid frBme, BUlmlJ/l bo}(. and the AJS~style of fO/WINd mounted magn610 Inrrotiuced
from Septembef 1951. The, Lucas instrument here IS of course the Wader type. It has the new-type front brake brought in
S'flptLImber 1952, the fullwidth front hub not arriving untU '2 months Ister
TEMPLE PRESS LIMITED

BOWLING GREEN LANE, LONDON, E.Cl
MATCHLESS SINGLES 1939-1955
..
www.carburetor-manual.com
Would you like some Free Manuals?
http://carburetor-manual.com/free-shop-manual-club-t-13.html
Also visit http://freeshopmanual.com for more Free Manuals
Also Visit my website for 7 FREE Download Manuals starting

with this one.
"The ABC's of Carburetion"

Click Here Now
file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]
This scan is explicit for non-commercial
DEFINITIVE PHOTOGRAPHS
(Left) Another maker's definitive

photograph showing the 350 cc
G3C as it was in 1938 with of
course girder forks and the
stylised M symbol on the
chromed tank
IMPORTANT NOTE
SlDce the tut wu wrItt.
for die 0JtaIuI book, AMC
LId .... ..,....t .... . buds _d the WooIwlc:h
fac ..., ......... clemollobed.
<AmmeJlta
about
over
ha............, .. the
DUIken ....o1d be ..... ...
..... Doh'.
_PedalW
Spua
and
senlce an DOW
coaceatrateclla the haDdI of
few UK deolen .....
btclude Mean HIUIlI'U _d
Joe Fnae" Moton RecBlde
Maker's definitive photographs

by courtesy of Motorcycle Sport
,-:Again a factory photograph. The

1954-season 5tXJ cc GBOCS in-
troduced from September 1953

with the new for that year
fuJl-mdth (ront hub of 7-inch
diameter
brake,
lightweight
welded (ront frame and
twin
seat. Rear legs are AMC's own
Jampots. The alfoy motor has

the magneto forward mounted
of course
This book:. is a practical guide carefully compiled to enable both the new owner and the expert
to carry out routine maintencance. complete overhauls. and to service those Matchless
single-eylinder machines built between 1939 and 1955. It will also be of assistance to dealers'
service staff as the comprehensive infonnation provided in the ten is culled from extensive
experience in servicing these machines.
To obtain maximum efficiency. reliability, and long life from component parts. regular and
systematic maintenance is essential. Performance. too, is likely to be improved if careful
attention is given to the instructions outlined in these chapters. The aim throughout has been to
guide the reader step by step through the sequence of dismantling and reassembly. paying
particular attention to the elimination of defects. and so avoiding those trial and error methods
which can prove so frustrating and. in the end, so expensive.
Chapters are devoted to ex- WD machines, giving conversions that will improve perfonnance:
and to trials and scrambles machines. Technical data and illustrations of special tools
recommended and used by the manufacturers are included ill the text.
Finally. the PubliShers wish to make grateful acknowledgment to Associated Motor Cycles
Ltd. for pennission to reproduce a number of their copyright drawings in the text BERNAL OSBORNE. Temple Press Ud.
FOREWORD TO THE ORIGINAL BOOK
CONTENTS
Definitive photographs .... .. ................. ............... .............. 1
D~r~onising th~ engine. ........... ......... ............... ....... ... ....... 3
Servicing the engine .. ..................................... ....... ..... ... ... ..... .. 5
Overhauling the engine .................................................................................... 9
Reassembling the engine ................................................................... 11
Pre-1955 Carburetters .......................................................... 14
The 1955 Monobloc carburetter ....................................... 15
The CP-type Burman gearbox ................................................................. 16
The B52type Burman gearbox ........................................................ 18
The clutch .................................................................................. 18
Competition and scrambles models .................................................................. 19
The transmission .............................................................................................. 21
Forks and frames ...................................................................... 22
Wheel bearings ................................................................................................ 25
Brake adjustment .............................................................................. 26
Dynamos ......................................................................................................... 26
Electrical equipment .................................................... 'Zl
Definitive photographs .............................................................. 26 et seq
WD-G3L drawing ............................................................ 31
Definitive photograph ................................................................ 32
Wiring diagrams ............................................................ 33 et seq
WD-G3L section ......................................................................... 35
Useful data ...................................................................... :r7 et seq
Engine design changes ....................................................... 40 et seq
Permissible modifications ....................................................... 41
WD-G3L illustrated spares lists ............................................. 42 et seq
Maker's 1948 advertisement ............................................................ 59
An official photograph, courtesy of Motorcycle Sport, revealing the side and rear of the AMC
factory at Plumstead, taken from the comer of Burrage Grove_ The front, hidden here, is in the
paraNe! Plumstead Road. Date is unknown but certainly is the early 1950's
EDITOR'S PREFACE
The only workshop manual currently in print for Match&ess 350 and 500 cc heavyweight
singles, this book has had considerable extra material added by the publishers, Bruce
Main-Smith Ltd. I have included an expanded WO-G3 and WO-Gll section which also features
the factory illustrated spare parts lists in full on the mUitary 350'5; my thanks to Mr
Martin of
leighton Buzzard for the loan of a set of mint-condition lists for this purpose.
There is also a greatly Increased amount of tabular information not found in the original
Temple Press edition.
The machines covered are of course those the factory came to call lat a later date)
heavyweights, to distinguish them from the lightweight 250 and 350 cc ohv singles with their
Phil Walker designed engines, gearboxes and frames introduced in June 1958 under both AJS
and Match&ess brand names by Associated Motor Cycles ltd, then of Plumsteacl Rd, Woolwich,
london SE1S. The heavyweights can be instantly identified by their usage of a conventional oil
tank behind the engine. The lightweights used no oil tank as such, lubricant being carried
dry-sump-wise in a reservoir cast integrally with the crankcases.
Though there are d'lfferences between early postwar AJS and Matchless heavyweights notably the positioning of magneto and dynamo - this workshop manual will serve reasonably
well for AJS too. Cams as manufactured by AMC were dual marked for both engines.
Otherwise the motors were broadly similar and of course the cycle parts were identical other
than for insignia and detail differences attendant on dynamo/magneto mountings and drives.
Both types of Burman box are dealt with in full. The AMC gearbox was not phased in until
April 1957 and is outside the scope of this manual - REG HIDE, Editor.
J.e.
Beyond the limit of periodic maintel"!slnce and running adjustments, the work
involved in decarbonizing a motorcycle engine is likely to constitute the first
venture by the owner into the rather deeper technicalities of his machine. It is
necessary on an average, fNery 5,000 miles or so, to clean away carbon deposit
from the i~side of the power unit -just as one would clean a domestic flue and
get more efficient combustion there15y. The job is an interesting one and usually
not too difficult to be carried out with the tools in the kk plus the few additional
items listed.
The engine should be decarbonized only when it shows a definite sign of
requiring attention. A gradual loss of power, poor compression, difficulty in
starting, combined with an increase in petrol consumption, are all signs that
decarbonizing is necessary. Conversely, SOme owners prefer to decarbonize at
fixed intervals of between 5,000 to 8,000 miles.
The risk in prolonging the interval between decarbonizing the engine is the
possibility of exhaust-valve burnin~.
.
.
.
Checking the compression from time to time will enable the owner to decide If
compression is satisfactory or otherwise. It is imperative- that the push-rod
adjustment is correct, also that the throttle is fully open when this check is made.
As work of this kind is usually carried out at week-ends, have ready the
necessary tools and spares, so that it can be completed without delay.
Suggested equipment for this purpose is listed below:

(j) Decarbonizing gasket set.
(ii) Valve spring compressor.
liiil Short length of rubber tubing with a l< -in.diameter bore with a nail
through one end to act as a tommy bar.
liv) Scraping tool, such as a cheap 6-in. steel rule with the corners ground
off.
(v) Grinding paste, jointing compound, clean rag and washing gear.
Dismantling
To start dismantling, remove:
(j) Petrol tank and petrol pipe.
(iii Exhaust pipe with silencer attached to it.
(iiil Sparking plug after detaching H.T. cable.
(iv) Throttle and air slides, leaving the needle in position. (Wfap these parts
in clean rag and secure them to the handlebar lug to avoid possible
damage.)
(v) Rocker-box oil pipe; use two spanners, one for the pipe nipple nut, the
other to prevent the union from turning. .
lvi) Cylinder-head steady stay, if used.
(viii Valve-lifter cable (for engines after 1948).
1. DECARBONIZING THE ENGINE
(viii) Three nuts and washers securing the cover for the rocker box' take off
the cover, turn the engine until both valves are closed then r~lease all
bolts securing the rocker box to the cylinder head.
Tilt upwards the right side of the rocker box and extract the two long
push-rods. The rocker box can now be lifted off.
Whilst the two push-rods are identical, it is preferable to refit them in the
original position. They should be marked suitably for correct order of
replacement. Remove:
(ix) Two valve end caps (for engines before 1949), then the four
cylinder-head holding-down bolts; the cylinder head can now be taken
away.
If it is difficult to separate the cylinder head from the barrel, place a short piece
of wood under the exhaust port and give the free end a series of light blows to
cause separation. Remove:
(x) Push-rod cover tubes; watch for a thin steel washer which may be
fitted on each tube below the sealing rubbers.
(xii Carburetter mixing body and float chamber attached. This can be dealt
with later.
In all probability the rocker-box gasket or pieces of it will stick to the cylinder
head. These can be removed with the steel rule previously mentioned, taking care
to ensure that particles do not obstruct the oil drilling in the cy6nder head.
Before removing the valve springs and valves, scrape the carbon deposk from
the cylinder-head sphere, also from the heads of both valves. The small amount
of carbon remaining can be removed after the valves have been extracted.
To remove both valves, a valve-spring compressor is required. The springs
should not be compressed unduly and only sufficient to extract the valve collets.
A sharp, light blow on the valve collar will help to separate the collar from the
collets.
On the 500 cc models both valves are similar in size, but different in material.
Valves are marked IN or EX on the valve end above the collet groove. On the 350'
cc models the inlet-valve head is larger in diameter than the exhaust.
With valves removed, scrape off the residue of carbon from the cylinder head,
remove also all traces of burnt oil or carbon from inside the exhaust-valve guide,
using a piece of emery cloth (most important on engines made before 1949), then
get rid of all particles of carbon from the ports and valve guides before starting to
grind-in the valves. Scrape the exhaust-valve stem and head; if emery cloth is
used on the valve stem, clean and polish with an up-and-down movement, not
rotary, as the valve stems are hard-chromed during manufacture.
A short piece of rubber tubing of l< in. internal diameter, pushed over the end
of the valve, is a suitable tool for valve grinding.
To grind the valves, apply a little fine-grinding paste on the valve face, insert
the valve into the head and press the rubber tube on to the valve end. Holding the
rubber tubing, pull the valve lightly on to its seating and turn the valve forward
and backwards, raising the valve occasionally of.( its seating, and continue the
process until the grinding compound ceases to "~ite."
When an even matt surface is seen on both the 'valve and the seating in the
head, grinding is complete.
Badly pitted valves, or valve seats, should be reseated by refacing the valve and
recutting the valve seat in the cylinder head. The valve angle is 45. Excess valve
MATCHLE~S
SINGLES 1939-1955
This scan is explicit for non-commercial us
DECARBONIZING THE ENGINE
grinding must be avoided, particularly as the valve seats in light-alloy heads are
not replaceable.
After valve grinding, wash the head and valves in petrol, check oil passages in
the valve guides and ensure that all tra(t. of grinding paste is removed. Pass a
piece of non-fluffy rag through each valve guide in turn. one way only, and then
squirt clean oil through passages in the -head for guide lubrication.
Check the valve springs for free length.,lt.the free length has decreased *-in.
or more, fit new springs.
Oil both valve stems and reassemble with springs, taking care that both collets
are correctly located in the two grooves ojl the valve stem.
To check if the valves arB seating correctly. wipe off oil from both valve heads
and the sphere of the cylinder head. Hold the head with the exhaust port vertical
and nearly fill the port with petrol. If after a few minutes petrol does not seep past
the valve, the seating is in order. Empty out the petrol, and if petrol is spilled into
the sphere of the head wipe it dry and repeat the test for the inlet valve, after
which the head can be put aside.
Set the piston on the top of its stroke, carefully scrape off carbon formed on
the piston crown, using the recommended toot The ridge of carbon formed in
the cylinder barrel should also be removed. Afford a little time in which to remove
the particles of carbon trapped in the gap formed by the top land of the piston
and .cylinder wall.
If the cylihder is removed to examine piston rings for gas leakage, do not
remove-the rings unless it is necessary. Gas leakage is indicated by black or
brown !,ortions on the ring bearing face.
Renew the cylinder-base gasket before refitting the cylinder.
Reassembly
The use of new gaskets is most desirable if one is to avoid again taking down
the engine after reassembly in order to rectify oil leaks and a leaking
cylinder-head joint. Cylinder-head gaskets of the solid-copper type can be used
again if not distorted or showing ovality in the bolt holes, by heating them until
cherry red and then plunging into cold water. This will make the gasket ductile.
Renew the two bottom push-rod tube rubbers,
Start assembling by:
(i) Turning the engine until the piston is on the top of its stroke with both
.,.
Top-haH components of the Matchless WD-G3L, e;,ea 1941

tappets down.
Hil Place new sealing rubber over each tappet.
(iii) Pull out and discard the two sealing rubbers for the push-rod tubes in
the cylinder head. Watch for the steel washer on top of each rubber;
press new rubbers into position, apply a little jointing compound on the
top end of each push-rod tube and insert them into the head with a
ro1ary motion.
Iiv) Clean the threads for the cylinder-head boits and apply a little graphite
grease to facilitate subsequent removal.
(v) Put in position the CYlinder-head gasket and place the cylinder head
and cover tubes into the cylinder barrel.
Some care and petience is needed at this stage to verify that the head gasket is
located accurately when the head bolts are passed through the cylinder head. Lift
the head slightly and see if the bolts go through the four gasket holes correctly,
then tighten down the head bolts diagonally until all four are firmly tightened. If a
torque spanner is available, set it to 36 Ib.ft.

Note: On early models the space between the carburetter air intake and oil tank
is restricted; it is therefore preferable to fit the carburetter to the cylinder head

before refitting the head and after dealing with the .carburetter as detaHed later.
Oil both push-rod ends before placing them in the push-rod tubes.
A new rocker-box gasket must be used, and this can now be placed on the
cylinder head. On engines made before 1949 there is a projection on the gasket
with a hole in it which must register with the oil-feed hole in the cylinder head
lubricating the inlet-valve guide.
Refit the two valve end caps (on engines before 19491.
Clean both faces of the rocker box; fit the centre rockerbox bolts first, put the
rocker box into position, tilt it and engage the push-rods with the two rocker
arms, tighten ligh~y the centre bolts, fit the remaining bolts and tighten all down
evenly and diagonally.
Remember that a soft gasket is used and exercise care by not over-tightening
these bolts, which may stretch or break if undue force is used.
Both valves must be closed when rocker-box bolts are tightened, and with the
engine in this position adjust push-rods SO that there is no noticeable
up-snd-down movement with free rotation. For engines with iron cytinder heads
this adjustment is made with the engine cold.
The petrol tank may be replaced temporarily so that the engine can be run for a
short period to settle the valve gear when a final adjustment can be made after
the engine has cooled down. On engines with alloy heads make this adjustment
with the engine reasonably warm.
Finally, before fitting the petrol tank and the rest of the parts removed, adjust
the throttle and air cables to take up slack; neatly arrange these cables, the H.T.
wire and lighting hamess, which should be attached to the frame top tube with
clips or adhesive tape.
Avoid overtightening the petrol-tank fixing bolts and secure these with copper
wire run through holes in tank bolts, thus joining front and rear bolts in pairs.
NCAF<80NIZING THE ENGINE / SERVICING ENGINES
FIG 2
~f\
!
I?r'~,1
')-.'0
Bottom-half crankshafts with drive-side crankcase.

(Above) For 1945-1954 medels. (Belowl For 1955-0n
FIG 3
2. SERVICING ENGINES
Heavy Oil Consumption

If the machine has covered considerable mileage with a gradual increase in oil
consumption, the cause can be due to worn or broken piston rings, cylinder wear,
or a combination of both.
The normal ring gap is 0.006 in. with a permissible maximum of 0.030 in. The
ring clearance in its groove is 0.002 in.
Should cylinder wear exceed 0.008 in., the cylinder should be rebored and a
suitable oversize piston used.
When fitting new piston rings a chromium-plated compression ring for the top
ring groove should be used, since this will minimize cylinder wear. These rings,
when new, have a slightly tapered exterior and are marked with the word TOP on
one side to indicate assembly position.
SERVICING ENGINES
An incorr~ly set oil-regulating screw, which controls oil supply to inlet valve,
can affect oil consumption. The correct position for this screw is half a turn open
from the fully-closed position. Worn valve guides will allow oil to enter the
combustion chamber.
Evidence of an excessive amount of oil in the valve-spring chambers can be
due to oil building up in the push-rod cover tubes on early-type engines_
The use of a later-type tappet guide with six slots, described in Chapter 3,
"Overhauling the Egine," will enable oil to drain into the timing chest more freely.
Excessive Smoke on Starting
The cause can be due to the details given for heavy oil consumption, or
excessive oil in the crankcase due to bad scavenging; alternatively, oil seeps into
the crankcase when the engine is stationary_ Bad scavenging can be caused by
an air leak between the cap covering the rear end of the pump housing or
obstruction in the oil passage from the sump to the pump.
In the event of oil seepage, this is usually due to a worn or scored
pump-plunger housing in the crankcase.
To decide if seepage occurs, use a dipstick to measure the oil level in the tank,
then check the oil level again after the machine has been standing overnight. If
the level has fallen the timing-side crankcase should be sent to the manufacturer
for examination and possibility of bushing the pump plunger bore.
Restriction in the oil-tank filter will affect the oil return from the sump.
Oil Pump Plunger
Inset is the fixed guide screw which engages in the scroll grooved in the plUnger body whereby
reciprocating action is added to the rotation of the plunger
. 7. Dowel peg. locating timing-gear cover

2. Timing-side flywheel axle with integral
Jlear for driving 011-pump plunger
3. on-pump plunger
4. Screw (one of three)
5. Guide pin
MATCHLESS SINGLES 1939- 1955
6. Screwed body for guide pin
Z Guide pin in position engaged in profUad

cam groove of plunger
8. Tapped hole (for oU-feed pipe to pump)
9. Tapped hole (for pipe returning oil to oU
tank)
This part of the engina should not be disturbed unless the crankcase is
dismantled or the oiling system becomes defective. The small hexagon bolt
housing the pump-guide pin, situated at the rear end of the plunger housing, is
often mistaken for a drain plug. If this bolt is unscrewed, either intentionally or
unintentionally, the pump plunger will be damaged beyond further use when the
bolt is tightened if the guide pin is not correctly located in the groove machined in
the plunger.
To ensure correct location the cap at the rear end of the plunger housing
should first be removed. If a short piece of spoke or stiff wire is inserted into the
hole drilled in the plunger, this can be moved slightly inwards and outwards
during the process of screwing home the pump-guide pin bolt by hand, and
finally tightening it with a spanner when correct location is effected.
Excessive tooth wear in one particular position indicates a restriction in the
feed line. This can be due to a blocked oil passage in the timing-side axle, the
crankpin or an obstruction in the rocker-box oil-feed line. Slight uniform tooth
marking is normal on engines that have covered a considerable mileage.
If the pump plunger is damaged after an engine overhaul, the timing-side axle
or crankpin are incorrectly located (see Chapter 3, "Overhauling the Engine").
If all the teeth are badly damaged the main-bearing spacing washer may be
worn (see the section on "Flywheel Assembly.")
Rocker Box Oil Suppl'y

If the oil supply to this part of the engine is gradually reduced or stops entirely,
wear at the end of the pump guide pin has developed and a new pin should be
used.
SERVICING ENGINES
FIG 5
FIG 6
Correct assembly of the oil
pump. Thespiralgrooveat
the end of the pump
plunger must mesh with

stationary peg shown at
the bottom of the sketch;
the plunger should both
rotate and reciprocate
when the engine is turned
by hand
The oilways in the valve guides

and in the head must align
An incorrectly located paper gasket used between the front pump end-cap and
crankcase will also stop the oil supply.
Crankcase Release Valve

This valve will be found on the driving-side crankcase, behind the primary
chaincase, and has a short copper pipe attached to it. The valve is a steel disc or
diaphragm, retained in the valve body, which has a serrated seat; the disc moves
towards the serrated seat as the piston descends, allowing pressure in the
FIG 7
crankcase to escape into the atmosphere.

If the disc is trapped between the valve body and the crankcase it will not
operate and will cause oil leakage from engine joints. It will also cause oil to
accumulate in the push-rod cover tubes and cause the engine to smoke badly.
If this valve is dismantled, place a little grease on the serrated seat to retain the
disc in position whilst the valve is refitted.
Oil Leaks
First ascertain the exact position of leakage as oil can run down the back of the
push-rod cover tubes and give the impression that the leak occurs at the
cylinder-base joint.
Oil leakage at the cylinder base can only be due to loose cylinder nuts or a
damaged paper gasket provided that the crankcase face is not bruised or
otherwise damaged.
Part-disassembled arrangement
of the Matchless aU pump
Defective rubber sealing rings at the top and bottom of the push-rod cover
tubes will cause oil leakage. If the cover tubes can be moved, there is insufficient
pressure on the oil seals.
To remedy, fit a -i-in. steel washer on the reduced end of the cover tubes
below the top sealing rubbers in the cylinder head.
An oil leak from the metal cap in the timing cover can be cured only by fitting a
new cap. Pierce a hole in the cap and prise it out, wash the aperture with petrol,
apply jointing compound on the outside rim of the cap and tap it into position. Let
the jointing compound set before starting the engine.
SERVICING ENGINES
A permanent cure is to grind *.-in. off the valve end and employ the hardened
valve-end caps used on earlier-type engines.
The oil modification to the rocker box should be included if the engine is made
before 1954. If the rocker is slightly worn it can be stoned, otherwise replaced.
VALVE LENGTH
Model
cc
Inlet Exhaust
Exhaust Valve Seizure or Sluggishness
1946-48
350
4-1.--in.
The symptoms of this trouble are misfiring - the engine cuts out with a
sudden increase in push-rod noise, usually after driving fast or after climbing a
gradient. Engines with light-alloy heads are not usually affected with this trouble
as the cylinder-head temperature is lower under normal driving conditions.
A heavy formation of carbon or burnt oil on the exhaust-valve stem and in the
guide bore causes the valve to become sluggish and possibly to seize when the
engine temperature increases.
To remedy, the head must be removed from the cylinder so that all carbon or
burnt oil deposited on the valve stem and its guide can be removed (see Chapter I,
"Decarbonizing the Engine"'. Reducing the oil supply will prevent a repetition,
which can be effected by inserting a short piece of *-in. outside diameter tube
into the hole in the rocker box, which feeds oil by gravity to the exhaust valve.
The tube should protrude -I.-in. to 14-in. above the rocker-box case.
As an alternative, a copper or aluminium plug with a small flat filed on it can be
inserted into the oil hole in the cylinder head, which registers with the
exhaust-valve oil-feed hole in the rocker box.
1946-48
500
H-in.
1949-57
350
4*-in.
500
4 ...... in.
Hairpin Valve Spring and Collar Wear

Engines made from 1949 up to 1953 are most likely to be affected by this kind
of wear and then usually the inlet spring only shows signs of it. This can be
prevented by increasing the oil supply to the inlet-valve rocker arm.
To modify, enlarge the oil hole drilled in the boss for the rocker axle to *-in.
Obtain a metering plug from the manufacturer, Part No. 018890, and insert this
into the enlarged hole. This plug has a small hole at one end; insert this end first
and tap the plug home. A further light tap with a centre punch will prevent the
plug from moving.
This adjustment reduces the oil supply to the exhaust valve, which is already
generous, and increases the oil feed to the inlet rocker. Later-type rocker arms,
valve end only, have a groove machined on the face of each rocker to convey oil
to the valve end and valve-spring collar.
1949-57
Valve Guides
All types are a force fit in the cylinder head and the guide protrusion away from
the port is of paramount importance. (See overleaf.' They are made from chilled
cast iron, are hard and somewhat brittle, therefore care to avoid breaking the
guide during the process of removal or refitting is most necessary.
To remove guides on iron cylinder heads, clean off burnt oil from the guide,
where it protrudes above the port, with emery cloth. With the head supported on
a bench, use a suitable drift to drive out the guide, or use a hand press if available.
When dealing with alloy heads, the head must be heated before attempting to
remove a guide, otherwise damage by enlargement of the guide bore will take
place. First ascertain if a circlip is fitted to the exhaust guide; this is a standard
fitting in all models after 1955. If a circlip is fitted, heat the head, tap the guide up
through the port so that the circlip can be prised out of its groove. Reheat the
head and follow the instructions given for iron heads.
Refitting Valve Guides

To ensure that the guide starts parallel with the guide bore, insert the valve into
the head, press the valve firmly on to its seat. Retaining the pressure, place the
guide over the valve and ensure that the oil hole is properly aligned; then press
the guide down as far as possible and, finally, tap the guide home to the specified
protrusion.
Loose Valve Guide

Wear on Valve Ends and Rockers
Wear on the valve-stem tips will certainly take place if engines made before
1949 are used without the hardened valve end-caps. Engines made from 1949 are
fitted with heat-treated valve-stem tips and are of a different overall length (see
Tables'. If the wear is slight the valve, after removal, can be turned goo to its
original pOSition, as wear by contact with the rocker forms a groove across the
valve end.
Removing the exhaust-valve guide on alloy cylinder heads without pre-heating

is usually the cause of this trouble. As a new head is expensive, a satisfactory
repair can be made by copper plating the external diameter of the guide to the
extent of 0.003 in. to 0.004 in. to close up the interference fit. Use a guide
machined for a circlip, together with a later-type valve-spring seat. If a radius is
ground on the valve-spring seat to clear the circlip, the original seat can be
retained.
SERVICING ENGINES I OVERHAUUNG THE ENGINE
Valve Guide Protrusion

Before 1948.
After 1948.
Inlet-valve guide, %-in.; exhaust-valve guide, %-in.

Inlet-valve guide, %-in.; exhaust-valve guide, Y.z-in.
Camshaft Wear
If the peak of either cam is bruised or badly worn, look for overloading on the
valve-operating Ilear. The usual reason is that the valve springs are coil-bound
when the valve IS at full lift (coil-type springs) or the valve-guide protrusion is
incorrect, causing the spring collar to foul the guide.
To check valve motion, turn the engine until the valve is at maximum lift. Place
a box key on the nut retaining the push-rod rocker arm and endeavour to open
the valve further; if further movement cannot be made the valve springs are solid
or coil-bound and should be exchanged for a set of the correct type.
If the cams are badly damaged, check also both tappets for wear and see
Chapter 3, "Overhauling the Engine," for removal drill.
Piston Slap
Engine noises of various kinds are often attributed to piston slap. which is
caused only by excessive clearance between the piston and the cylinder. Piston
slap is audible when the engine is pulling, or on changing up to a higher gear, but
not when the engine is running light or without load.
Reboring the cylinder and using an oversize piston is the only remedy for a
noise of this kind. The wire-wound piston which has been used for some time
permits the use of a close running clearance of 0.001 in. with a reduced risk of
piston seizure.
Engines made before 1947 can use this type of piston if the connecting rod is
exchanged for a later type, as there is a difference of %- in. in the two
connecting-rod lengths.
The small-end bush is not usually affected by premature or undue wear;
therefore piston slap should not be confused with a slack small-end bearing.
Big-End Noise
If a light ranle develops, which becomes inaudible when the engine is pulling or
under load, a little movement in the big-end assembly is usually the cause.
This does not indicate that the bearing is completely worn out, for it is often
FIG 9
Details of one of the few special

tools, 8 main-shaft timing pinion
extractor, suggested by the

makers
possible to 'cover a further 8,000 to 10,000 miles without effect on the engine
efficiency.
This noise can develop when there is an accumulated clearance between
0.0015 in. and 0.002 in. in the big-end assembly. It is possible that a new set of
rollers will absorb movement; alternatively, fit rollers plus 0.001 in. oversize after
lapping the connecting rod (see Chapter 3, "Overhauling the Engine"), prOVided
the roller path on the crankpin and liner are undamaged.
Timing Gear Noise
This noise can develop when there is lal an accumulated clearance between the
camwheels and small timing pinion, Ibl end-float between the cam which drives
the magneto and the crankcase, and lei wear on the bushes for the cams or a
worn timing-shaft bush, which would affect teeth engagement on the timing
gear.
First check for end-float by removing the magneto chain cover, run the engine
to develop the noise and press on the end of the shaft that drives the lower
magneto sprocket with a piece of wood or screwdriver handle. If the noise stops
there is end-float, which is cured by removing the magneto drive and the
timing-gear cover and fining a shim washer either 0.006 in. or 0.010 in. thick over
the shaft for the cam wheel before refitting the timing-gear cover.
Backlash can be verified by reproducing tha noise and applying pressure on the
top run of the magneto driving chain with a wooden screwdriver handle. If the
noise stops, try first a new small timing pinion before replacing the cam wheels. If
the noise persists, check for worn bushes.
Noise in the Rocker Box

A little end-float in the rocker axles is of no consequence. This movement can
be taken up by tapping outWards one of the two bushes after removing the
rocker arm, axle and sleeye. The rockers should move freely if the bushes are
correctly located.
A distorted hairpin-type valve spring may make contact with the rocker box.
Reversing the position of the spring may have the desired effect. Look also for a
groove on the valve spring at the point where the rocker operates - this can also
cause a noise. A slight radius ground on the rocker arm at the position of contact
will prevent a recurrence. If the spring is badly grooved it should be discarded.
3. OVERHAULING THE ENGINE
Provided workshop facilities, together with an adequate supply of box keys

and spenners are available, no great difficulty should be experienced in dealing
with work of this kind.
Some thought on preparation for overhauling is desirable by having available
such items as an extractor tool for the dynamo sprocket, a small timing pinion
extractor, a spare parts list, a complete gasket set, jointing compound, preferab:y
of the type that does not flake, such as 'Wellseal', wooden boxes to
accommodate parts as they are removed. When dealing with engine work,
cleanliness is vitally important both in the handling and fitting of moving parts.
Invariably the under surface of the crankcase is oily and impregnated by road
grit, SO start by cleaning the exterior of the engine before dealing w;th the interior;
detergents or solvents are obtainable for this purpose.
A careful note as to the position of bolts, distance pieces and washers should
be made during the process of dismantling; nuts and washers replaced on the
bolts as they are removed will save time and patience when the machine is put
together again.
The timing gear of the engine is a

very simple a"angement. Inset
are seen the tappets and guides
and the oR pump rotor shaft of
the WD engine
OVERHAULING THE ENGINE
FIG 11
Removing the Engine

Commence dismantling by following the instructions for decarbonizing the
engine.
Proceed to remove:
mThe outer portion front chaincase and place a tray underneath it to

catch the oil.
(ii) The battery and strap securing its carrier to the back half of the
chaincase.
(iii) The clutch outer plate with springs and thimbles.
(iv) The circlip and lock washer from the dynamo sprocket. Engage top
gear, apply the rear brake and unscrew the engine sprocket nut, using
a ring spanner and tapping the free end.
(v) The gearbox mainshaft nut securing the clutch (early type 1-in. across
flats, later type 1'\--in.).
(vi) The nut securing the dynamo sprocket nut wkh a thin spanner on the
flats at back of sprocket to avoid ben~ing the armature.
Exploded drawing of timing gear, valve Bctuatinp mechanism. and magneto drive. It also shows
the 00 pump parts. valve lifter parts and timing side crankcBSe of the WD G3L engine
(vii) Disconnect the front chain then take off the dynamo sprocket using
wedge-shape tool.
(viii) The clutch assembly; watch for 24 rollers, which wHi drop out.
(ix) The shock absorber assembly and engine sprocket with the distance
piece at the back of it.
(x) The rear portion of the front chaincase; straighten the three tab
washers before applying the small box key.
(xi) The bolt securing the chaincase to the engine and identify the location
of the two dissimilar distance pieces.
Most of these parts will be oily or messy so keep them in a box away from
engine parts.
Drain the oil tank and whilst this is taking place remove:
(xii) Both oil pipes, tank end firat, then the rocker-box oil-feed pipe.
(xiii) The magneto chaincase cover.
(xiv) Both sprockets for the magneto chain (magnetos with auto-advance
are self-extracting). Use the dynamo sprockettool for the top sprocket
(early models) and a tyre lever (with its end bent at right angles) for the
camshaft sprocket.
(xv) The timing cover on the crankcase.
(xvi) Disconnect the ignition control cable (handlebar end), and then
remove the magneto platform with the magneto attached and identify
the location of the distance pieces where fitted.
(xvii) Remove all bo1:ts passing through the crankcase and loosen the
gearbox bolt nuts. It will be easier to lift the engine out of the frame if
the cylinder is left in position, but it may be necessary to spring out the
front frame down tube when the engine is lifted out.
Note. - When unscrewing the oil-return pipe nut (top nut) at the crankcase
end, take care that the spanner does not touch the feed pipe nut (lower nut) thus
Cam Wheel Bushes
creating a levering action on the lower nut which can break the crankcase.
With a two-diameter drift drive out the cam-wheel bushes. The metal cap in
the timing cover must be pressed out before the bush behind it can be removed.
DISMANTLING THE ENGINE

Thoroughly clean the exterior of the crankcase before it is placed on the bench,
then remove the sump plug to drain the oil. Remove:
(i) Both oil-pump end-caps, the pump guide pin, and take out the oil-pump
plunger, before attempting to separate the crankcase.
(ii) The small timing-pinion nut which has a left-hand thread.
(iii) Both cam wheels.
(iv) The timing pinion.
(v) The bottom crankcase bolt if fitted.
(vi) The cylinder barrel. If a compression plate is used it will come away with
the cylinder.
(vii) One circlip only, push out the gudgeon pin and take off the piston. If the
gudgeon pin, which is a sliding fit, is difficult to extract, remove burrs
round the circlip groove. Wrap the piston in clean rag and put it in a
place of safety.
The crankcase can now be separated and the flywheels taken Out.
Big-End Assembly
Squirt petrol through holes in the timing-side axle with the object of removing
oil from the big-end bearing so that up-and-down movement between the
connecting rod and bearing can be detected_ Should there be no up-and-down
movement but the connecting rod can be rocked sideways (this must not be
confused with side clearance between the rod and flywheel), then attention is
necessary.
Separating the Flywheels

Remove both crankpin nuts; use a separating tool as shown in Fig. 6, or
alternatively an Arbor press, to separate as the crankpin centre is a force fit in
both flywheels. Check crankpin roller path and connecting-rod liner for wear or
damage.
Timing-Side Bush
Support the crankcase with a short length of steel tube (1 y". in. outside
diameter, 1 ~-in. internal diameter) placed in the timing chest around the bearing
bore in the crankcase, and force out the bush.
If a bush with two diameters is used, support the crankcase and force out the
bush from inside the timing chest_
Tappet and Guides

The tappet and its guide can only be removed together. Some difficulty may be
experienced as the guides are a very tight fit in the crankcase. Repair shops and
the manufacturers use a special tool.
These guides should only be removed when the tappet feet are wom, or when
the six-slot guides are to be fitted.
The valve-lifter shaft, if fitted, is removed and the two crankcase halves bolted
together to prevent distortion_
Without the special tool, heat the crankcase uniformly and drive out tappet and
guide from inside the timing chest.
Rocker Box
To dismantle the rocker box completely, remove both rocker-axle nuts and
washers securing the valve-end rockers_ Tap out each axle or prise off the rocker.
The axle with its loose steel sleeve and push-rod rocker attached can be
withdrawn.
The rocker-axle sleeve is mounted on two short bushes with a felt sealing ring
between each bush.
Heat the rocker box and press out the four bushes.
Flywheel Shafts
Remove the nut retaining the driving-side axle which has a right-hand thread
and push out the shaft, which is usually a tight fit, from inside the flywheel.
Take out the grub screw alongside the nut retaining the timing-side axle
(engines before 1954), unscrew the nut a few turns and tap the end of the shaft
sharply to remove it as it is a taper fit_ Take off the nut when the shaft is loose.
Engines from 1954 onwards have a parallel shaft and must be pressed out.
Main Bearings
To remove the bearings, uniformly heat the crankcase and drop it face
downwards on to a bench; the bearings with spacing washers will fall out_
11
REASSEMBLING THE ENGINE

Connecting Rod
A detachable liner is fitted to the connecting rod. Uners sold as replacements
are ground internally to allow for contraction when fitted; even so complete
concentricity cannot be guaranteed as contraction is controlled by the
interference fit of the liner in the rod_ To ensure concentricity a lapping tool is
used with grinding compound.
If the big-end assembly is correct the rod should just fit over the rollers, with no
appreciable side rock.
Fit the timing-side axle, with the oil hole in register with the hole in the
flywheel. A jig can be used for ensuring accurate register. Tap the shaft home (if
a taper shaft is used) to prevent it turning while the nut is tightened (do not
overtighten the nut). After the nut is in position fit the grub screw.
Where the shaft has a parallel shank use a press to force it home, then firmly
tighten the nut. A grub screw is not used with this arranQement..
Insert the crankpin and washer, if fitted, into the flywheel with both oil holes In
register and press the crankpin home. Apply oil to the crankpin, fit the cage and
fill it with 14-in. by14-in. rollers (a total of 30). Apply more oil to the cage and
rollers, fit the other washer, then take up the driving-side flywheel. Press home
the shaft, ensure that the Woodruff keys (if two are fitted) do not fall out, and
firmly tighten the shaft nut.
.
.
Offer up the flywheel on the crankpin and align as near as possible, With a
straight edge on both rims, then press the flywheels firmly together. If this
process is omitted the flywheels will flex and break the crankpin. Therefore do
not rely on the nut pressure. Run down the crankpin nuts evenly to avoid
disturbing the centre shaft and firmly tighten both nuts. The torque spanner
setting for these nuts is 190 lb. ft.
Set the flywheels to run true with maximum error 0.00110.002 in. Check the
error between centres with a gauge on the shafts as close as possible to the
flywheel face.
Crankcase
To fit a new timing-axle bush, support the crankcase and insert the chamfered
end of the bush first and press home. The bush will contract when in position;
ream to the dimensions given in the Appendix. The long plain bush may need
adjustment to obtain the specified amount of flywheel end-float. Insufficient
end-float can cause seizure.
The narrow roller bearings and short bush fitted to very early engines are no~
obsolete. The substitute is a two-diameter bush. The steel sleeve for the roller IS
retained to locate the new-type bush on the larger diameter.
Flywheel Assembly
the rubbing action of the inner race caused by the bearing jamming because of
foreign matter.
The driving-side shaft can be used to locate the bearing spacing washers.
Cam Wheel Bushes
Bushes are fitted chamfered end first, flush with the housing; care should be
taken to fit the bush correctly in the timing cover for the camshaft that drives th~
magneto. A spiral groove is machined at one end of the bush to prevent all
leaking into the magneto chaincase. This spiral groove should be on the outer
end next to the magneto drive sprocket. To fit the timing c.ov.er to the cra!,kcase
use a pilot reamer through both bushes. Take off t~e tl~lOg cover.., f!t both
camwheels and adjust for end play with shim washers, I.e., nil end float With free
rotation.
Tappets and Guides

Bolt together both crankcase halves, heat the crankcase, insert tappets in the
guides, drive downwards until the guide is flush with the crankcase.
Refit valve lifter if used.
An extended impression of the

G3L bottom haN components
comprising an exceHent example
of a built-up crankshaft assembly
Driving Side Bearings

Engines made from 1952 up to 1955 have two diameters in the bearing housing,
sometimes mistaken for incorrect machining or wear. The outer bearing nearest
the sprocket is a close interference fit, the inner bearing is a slight interference fit.
This allows the inner bearing when in position to be tapped away from the outer
bearing thus preventing end loading and permitting both inner races to rotate
independently and freely.
If a bearing that is normally a close interference fit is loose in its housing, the
housing can be knurled or a copper deposit 0.002 in. thick used on t~e outer
perimeter of the bearing. The bearing must be completely shrouded, leaVing only
the perimeter bare, before it is immersed in the vat.
.
To fit the bearings, the crankcase must be heated. The assembly order With
spacing washers is shown in the illustrations.
On the 1955 models one large and one smaller bearing with one spacing
washer only are used. Wear on this type of spacing washer will create flywheel
end-float and possible damage to the oil-pump plunger. This wear is the result of
12
Rocker Box Assembly
Compression Ratios
If new bushes are fitted, heat the rocker box and first fit the two inside bushes
'
then the outside bushes, which should protrude approximately 0.010 in.
Ream the bushes to the dimensions sat out in the 'Appendix, remove swar! and
fit new felt saaling rings into the space between the inner and outer bushes.
A taper mandrel or a paint-brush handle can be used to press the rings
outwards and into position, otherwisa difficulty will occur in entering the rocker
sleeve.
Assamble the rockers, firmly tighten the axle retaining nut and washer.
If the rocker is stiff to move, due to a lack of end play, a light tap on the outside
rocker-axle nut will move the bush inwards to give free movement. When end
play is excessive, take out the rocker-axle assambly and tap the inner bush
outwards, 10 the required amount.
The compression ratio of pre-l955 models can now be raised to 7.3 (500 ee) or
7.5 (350 cc). Actually the fitting of a 1956 piston to 1952 500 cc models sarves to
raisathe compression ratio to 7.3: 1. On pre-l952 models the compression plates
can be dispensed with after the ridge formed in the top of the barrel is honed out;
it is absolutely essential to do this. The fitting of a new piston to the 350 cc
machine (7.5: 1 and no compression plate) fulfils the same object. No alteration is
required to either the ignition timing or carburation. The special piston used on
scrambles machines gives a ratio of 8.3 (500 cc) : 9.5 (350 cc) but these pistons
are not suitable for standard models.
Plugs recommended are long reach (alloy heads): KLG FE 100: Champion NA
10: Lodge 3 HLN: KLG FE 220. Short reach (iron heads): KLG F 100: Champion
L-llS: Lodge 3HN: KLG F 220. These grades provide for a higher heat factor
consaquent upon fast riding.
AssembUng the Crankcase

Apply some clean oil to the bearings, bushes and tappet guides.
Fit both crankcase halves to the flywheel assambly. Bolt the crankcasa
together with at least four bolts, also with the bottom bolt if used.
Test the flywheels for free rotation, then check for end-float, minimum 0.020 in.
to 0.025 in.
Where a long plain bush is usad, it can be pressed either inwards or outwards
to allow correct end play. In the casa of a two-diameter bush, face back the bush
as required.
The oil-pump plunger can now be fitted with care to locate correctly the guide
pin.".
. Fitj\~on, with the split in the skirt face forwards. Take care to ens.ure that
the gudgeOn pin circlip is correctly located.
Apply clean oil to both the piston and cylinder bore, slacken all bolts passing
through the crankcasa and position the crankcase so that both halves are flush
with each other when the cylinder is bolted down.
Fit the small timing pinion.
Re-install the engine by reversing the instructions given for removal.
For details on refitting the cams see the following section.
Camshafts
It is possible to modify by fitting high-lift and racing camshafts. In this case the
boss surrounding the timing-side bush on earlier models has to be machined to
provide clearance for the higher lift of these cams. W.tII!re machines are fitted
with a valve lifter in the crankcasa, the valve-lifter s"iIJ will require adjusting
otherwise the valve clearance and valve timing will be wrong. Valve movement
should also be checked. Racing camshafts should not be used on machines fitted
with a silencer or loss of power will result. High-lift cams (marked HL) increase
the volumetric efficiency of standard models. Cams marked SH are for usa with
open exhaust pipe.
The valve timing of both require alteration (see Chapter 6: "Competition and
Scrambles Models") and so will the carburetters if full benefit is to be derived.
The manufacturers recommend carburetter bore sizes of l*-in. (500 cc) l*-ir;.
(350 cc).
13
Ignition Timing
A careful check is essential and it is recommended that the manufacturer's
setting should always be used. Much care is taken to determine these sattings
and it is extremely unlikely that better ones can be chosen. Excessive ignition
advance in thesa days of high-octane fuel, and consequent ability to run without
pinking, produces considerable stressas on the big-end assambly. The
importance of correct contact-point satting (0.012 in.) cannot be overemphasized.
To check ignition timing, sat the contact-breaker points at 0.012 in. Remove
the rocker-box cover and plug. Turn the engine until the inlet valve opens and
then closes and, with a rod, check the position of the piston through the plug
hole. Engage top gear in order that the piston can be rocked; usa the rear wheel
and rotate the engine shaft until the piston is at t.d.c. Mark the rod where it now
registers with plug seat and then remove it and make a mark half an inch higher
up the rod. A cigarette paper should now be insarted between the
contact-breaker points; sat the ignition lever to full advance (A.T.D. units can be
fixed in that position with a small wood wedge) and again insart the rod into the
plug hole. Tum the engine back until the half-inch mark registers with the
plug-hole seat. The contact-breaker points should be just about to open at this
stage, so freeing the cigarette paper. Half an inch before t.d.c. with the manual
control or A.T.D. fully forward is the maximum recommended by the
manufacturers. If it is necessary to reset ignition timing, leave the sprocket loose
on the camshaft. To remove the sprocket, loosen "the nut a few turns and, with
the turned-in end of a tyre lever inserted behind the sprocket, lever it off. If it is
difficult to remove, tap the shaft end with a mallet whilst maintaining leverage.
A.T.D. unit nuts are salf-extracting and will presant little difficulty.
Oil Filters
Pre-l956 machines were fitted with felt filters in oil tank, giving a cleansing
phasa during the passage of lubricant from sump to oil tank. A strainer
is fitted in the oil feed pipe to prevent extraneous matter entering the feed side.
When major engine overhauls have been completed, the oil and filter need
attention after a further 500 miles. Change the oil and clean the filter. Attention
should be given again after 5,000 to 6,000 miles have been covered.
MATCHLESS SINGLES 1939 -1965
Erratic Running at Slow Speeds

Check the pilot jet, for this is usually responsible by being blocked or wrongly
set; look for airleaks, a distorted flange face; or the erratic running may be the
result of wrong mixture. Slow-running and mixture control can be improved by
opening out the hole drilled diagonally through the mixing chamber to the inlet
tract (pilot outlet), using a No. 66 drill 10.033 in.) in conjunction with a
watchmaker's hand chuck, or eclipse pin vice No. 121. Great care should be
exercised not to use undue force. Remove burrs ftom the hole.
This alteration is recommended in order to obtain full control on pilot
adjustment during the increase of volume of fuel fed to the engine. Pilot-screw
adjustment should now be 1 Y.. to 2 turns open. It is essential that positive
slow-running is obtained by adjusting the pilot air-control screw before the
engine becomes unduly hot. If this adjustment is made with the engine unduly
hot, the final setting will be weak. It has been established that positive
slow-running is best obtained with the plug gap set at .020/.022 in.
Petrol Consumption
When checking with a view to improving m.p.g. figures ensure that the
carburetter is not faulty by reason of ovality in the needle-jet aperture, also that
the float is not faulty. Fit a new needle jet and float if in doubt and see that the
engine is in good general condition.
FIG 13
PRE-1955 CARBURETTERS
,,,
I
Throttle Slide
The degree of cutaway is determined by the manufacturers. The slide, as fitted
to the standard models, is usually adequate but, if it is intended to alter this, an
understanding of the principles involved is desirable.
Slides are marked on the head, the first figure indicating the type, and the
second the amount of cutaway in sixteenths of an inch. The mark 29/4, for
instance, shows that the amount of cutaway is !4-in. Using a larger cutaway
weakens the mixture; a smaller cutaway enriches. To remedy a weak or flat spot
after leaving the pilot phase, use a smaller slide cutaway. This increases petrol
consumption, so before changing a slide check that the pilot setting is not weak
and thus the cause of the trouble. A surging effect will be noticed at 30-40 m.p.h.
if the cutaway is too shallow.
Fuel Consumption
A few hints on this topic may assist the tyro rider. No gain in fuel consumption
will be achieved by reducing the main jet size (if the recommended jet is already
fitted) except after the throttle is more than three-quarters open. Needle position
affects fuel consumption and engine performance only at about 50 m.p.h. or
more. But raising the needle improves acceleration. The answer to high fuel
consumption is to keep the throttle turned well down.
A sectioned drawing of the

standard Ama/ c8rburetter fitted
to all Matchless models up to the
introduction of the "Monab/oc"
14
:;ilencer Noises
An uneven or explosive exhaust noise is usually due to the effect of a weak
pilot setting, revealed when the throttle is nearly closed or closed. If the exhaust
pipe is loose in the exhaust PO" this, also, will cause silencer noise. Check the
throttle slide for wear. This has the effect of admitting air additional to
requirements, producing a weak mixture. To remedy the loose exhaust pipe.
swell out. the end with a taper cylindrical wedge.
(Below) The "Monobloc" body
showing removed the slide stop,

slowrunning screw and pilot jet
THE "MONO BLOC" CARBURETIER (1955)

This instrument introduces many new features, among them a removable pilot
jet and a combined fuel and mixing chamber. The primary air choke has a
compensating action in combination with two bleed holes in the needle jet which
serve the purposes of air-compensating the mixture from the needle jet and
providing a reserve of fuel for sharp acceleration. Tuning routine is very similar to
that for the old-type carburetter and presents little difficulty.
To Remove the Float

Take off the side-cover fixing screws; raise the float off the hinge pins and
check for punctures. When re-fitting see that the narrow hinge leg is uppermost.
To Remove the Float Needle

Remove the banjo bolt, washer and filter gauze; unscrew the needle seating
and lift out the needle; check the pointed end and seating. Care should be
exercised when handling the needle and gauze.
To Remove the Pilot Jet

Remove the pilot-jet cover nut and washer and unscrew the jet with a
screwdriver. Ensure that the pilot by-pass and the pilot outlet are clear. On
assembly see also that the pilot jet is not over-tightened, for a damaged pilot-jet
seating cannot be rectified.
To Remove the Jet Block
FIG 14
IJut
Take outthe air and throttle slides, the jet holder, complete with needle jet and
main jet, and unscrew fully the throttle-slide adjuster.
the jet block from
the mixing chamber, watching that the gasket at
base is undamaged,
otherwise fuel will leak across the face, resulting in hea
onsumption and a rich
mixture. When replacing the slide, carefully locate the taper needle in the jet
block.
Adjustments
The following sequence should be observed;
First check the rocker adjustment, plug gap and contact-breaker points. Screw
home fully the pilot air-adjusting screw, then unscrew it 1 % turns. For engines
15
Details of the Ama/ "Monobloc"

type, 376/5 and 389/1 carburetter fitted respectively to 350 and
500 cc models from 1955
fitted with manual ignition control, retard the lever % in. Now warm-up the
engine with the air lever fully open and set the throttle-adjusting screws so that
the engine runs just too fast for idling or slow-running speeds with the twist-grip
closed. Then gently unscrew the throttle-adjusting screw to reduce the engine
speed until the engine falters. Finally screw in or out the pilot adjuster until the
engine runs evenly and slowly. If engine speeds increase rapidly, the setting is too
weak. Recheck. Open and close the throttle sharply and check for any falter. The
engine must not be allowed to become too hot during this work, so complete the
slow-running setting first and as quickly as possible.
OVERHAUUNG THE ENGINE / GEARBOXES
SmsII clearance in the split pushrod and baH assembly is essentisl
Petrol Consumption
FIG 15
Fuel wastage can be caused by incorrect setting of the pilot jet and consequent
flooding. Fit a new nylon needle and check the washer at the base of the jet
block. On old machines fit a new needle and needle jet but do not alter the jet
size.
Pre-l956 350 cc machines can be adapted to use a larger cutaway slide (size
3 %) which should show a petro) consumption improvement of up to 13 m.p.g. at
40 m.p.h.
When fotting a new jet block, ensure that the holes in the mixing chal1)ber
register with those in the primary choke. If necessary, the taper needle can be
lowered one notch but it should be borne in mind that this reduces the
acceleration rate.
4. GEARBOXES
THE CP-TYPE BURMAN GEARBOX.
This gearbox is fitted to W.O. models and 1945-51 machines. Pre-l948 boxes
were grease lubricated; 1948-51 were lubricated by S.A.E. 50 oil (capacity 1 pt.).
Hypoid 80 or 90 has also been satisfactorily used consequent on improved types
available in the 1960's.
Gearbox Noises
If the transmission is noisy in third gear, look for wear on the
layshaft fixed pinion and/or main driving gear, which engages with the layshaft
fixed pinion. Also check the layshaft bush.
Noisy gear engagement when the machine is moving off is due to clutch drag.
Holding the clutch lever tight against the handlebar depress the kickstarter lever.
If, after this, the gear engages without noise, clutch drag is confirmed. Check for
clearance ( *-in.) between the operating plunger and the nose on the operating
lever by testing the top end of the clutch withdrawal lever. It should move about
*-in. to and fro.
Check for sticky friction plates, caused by oil residue, and, if necessary, clean
with paraffin. At the same time, check for buckles in the plain plates. Check that
the pressure plate is running true. Pull out the clutch lever, depress the kickstarter
Gear Selection
If engagement is uncertain, check the rocking-pawl mechanism for wear or for
a broken spring in the spring box. Ascertain that the assembly is correct by taking
out the footchange assembly. The small pinion on the camshaft is marked with
an "0"; tum the shaft until the "0" is at nine o'clock and remove the
foot-change mechanism. The toothed sector engages with the camshaft pinion,
also marked "0:' With both marks in register the gears are indexed correctly. If
difficulty continues, worn striker forks are likely to be the cause of the trouble.
FIG 16
autch-operating lever with baH-
thrust mechanism and compon-
ent parts, including adjuster pad,

on the Burman CP-type gurbox
Top Gear
If top gear disengages under load, the striker forks are probably worn, or
possibly the main driving-gear bush has moved towards the kickstarter side of the
gearbox, preventing full engagement of the gear. Fit a new bush.
16
and watch for plates rotating out of true. To cure, balance the clutch springs
equally. Check that there is sufficient clutch-plate separation; it is sometimes

lacking, due to wear in the operating mechanism.
Clutch Fails to Disengage

Check the nut retaining the kickstarter ratchet pinion, the thrust stud in the
clutch pressure-plate and the clutch-hub retaining nut. The push-rod and
operating lever should be checked if trouble has developed gradually.
Kickstarter Faults
If the kickstarter fails to engage, or sticks up, it is usually due to damage of the
first tooth on the quadrant; this can be ground off with little loss in leverage. The
trouble is often due to the absence of a stop rubber. If the kickstarter fails to
return to the neutral position, check for a broken spring and for seizure on the
shaft.
GEARBOXES
Power Tr!lnsmission through the Gears

First (lowest! Gear
Sliding gear, Fig. 17, "c" on the mainshaft is in the midway position, that is,
disengaged from gear "8" and "0:' The layshaft sliding on clutch "W" moves to
the right and engages with gear "G:' Power now is transmitted through clutch
A" to mainshaft "r;' mainshaft sliding gear "e;' layshaft gear "G;' layshaft 'W:'
layshaft "V;' layshaft gear liE:' to main gear "S" and chain sprocket "J:'
II
Second Gear
Sliding gear "c" on the mainshaft is in the midway position, that is,
disengaged from gears "8" and "0:' Layshaft sliding clutch "W" moves to the
left and engages with gear "F:' Transmission is by way of clutch "A:' to
mainshaft "r;' mainshaft sliding gear "e;' layshaft gear "F:' layshaft clutch "W:'
layshaft "V:' layshaft gear "E:' and main gear "B" to chain sprocket "J:'
. Gearbox Mainshaft End-Play

Assuming the kickstarter pinion nut is tight, check the small bearing of the
mainshaft in the kickstarter case. Shim washers placed between the bearing and
the housing may provide a remedy if wear is not too advanced.
Clutch Rattle
Sometimes experienced when the engine is idling. It is due to backlash
between the tongues on the clutch friction plates and the slots on the clutch
driver. If the clutch is pulled in and the noise disappears, that is the trouble.
Renew clutch driver if wear is considerable.
,
Clutch Sprocket Movement

This is usually due to wear on the clutch hub rollers and/or sleeve. If the
bearing surfaces are correct, the width of the mainshaft bearing sleeve can be
reduced and new rollers fitted.
Broken Pinion Teeth

In order that further trouble may be avoided after fitting new gears it is
essential that both the mainshaft and the laYShaft.uld be checked for
straightness before reassembling. If there is a bow, an
slight, the shaft can
be straightened between V blocks.
It may be of interest to readers to study the working of a gearbox, usually taken
for granted by the majority of riders.
The illustration is of the CP-type 8urman gearbox, which has four forward
gears and has positive-stop foot gear-change mechanism. The component is
clamped between the two rear engine plates by two bolts, the bottom bolt acting
as a pivot. The top bolt passes through the gearbox top lug and the rear plates,
which are slotted; this allows the gearbox to be moved to adjust the primary
chain.
17
FIG 17 The CP-type Burman gearbox-clutch assembly
Thkd Gear
.
Sliding clutch "W" on the layshaft is in the midway position, that .s,
disengaged from gears "F" and "G:' Mainshaft sliding gear "C" moves to the
right and engages with gear "0". The transmission is through clutch "A", to
mainshaft "T:' to mainshaft sliding gear "C:' mainshaft gear "0:' layshaft gear
"H;' layshaft "V:' layshaft gear "E" and main gear "B" to chain sprocket"J:'
Fourth (highest) Gear
.
Sliding clutch "W" on the layshaft is in the midway position, that .s,
disengaged from gears "F" and "G:' Mainshaft sliding gear "C:' moves to the left
and engages with main gear "8:' Power is controlled by clutch "A:' mainshaft
"T:' mainshaft sliding gear "e" and main gear "B" to chain sprocket "J:'
THE B52 BURMAN GEARBOX

This gearbox is fitted to 1952-55 machines. Oil capacity, 1 pt. S.A.E. 50 grade.
Hypoid 80 or 9O __may also be used.
-:,x< . \ r" ,
'SkF
\'---.-.
{,2'''j
'
' ~-
FIG 18 Section through the
Burman 852 gearbox

showing gears and
clutch mth
actuating
mechanism
A. ... Low a- on meinlhaft.

B Third gMI on malnshtft.
C.... Second De. on meinlhaft
D.. M.... drMng .....
E law ...... on ...,...,..
F.. n.d gur on I8y&hatt.
G.... Second gear on a.v.Mft
H... SmII pinion on ~
Gear Selection
Faulty selection is almost cenain to be due to the small cam-barrel plunger
sticking in its housing. Rub down the plunger with an abrasive and apply oil.
Top Ge~r
If top gear disengages under load (early 1952 models), the probable fault is that
the main-bearing housing is machined too deeply and so causing panial
engagement between the main driving gear and the mainshaft sliding gear. Make
a steel washer, v-in. thick, and place it between the main bearing and the
housing.
GEARBOXES I THE CLUTCH
FIG 19
Foot-change springs on the 852 gealbox
Kickstarter Faults
If the crank sticks, ease the cover screws and then depress the lever. The
spring is probably broken if the crank does not return to its position. If the crank
returns, the loosened state of the screws may show that normally the kickstaner
axle bearings in the case and cover are out of line. Ensure that the kickstaner axle
is perfectly clean. 00 not use the machine with the kickstaner left in an incorrect
position.
Oil Leakage
"
Leakage can occur from the two metal caps that seal the shaft holes, or from" ,-'
the main-bearing oil seal. Leakage from the kickstaner cover case is due to a
broken or defective gasket fitted between the case and the cover. To stop an oil
leak from the twe metal caps wash the pans with petrol; use jointing compound
in both apenures and allow to set. Try this first before replacing the oil seal.
Gear Disengagement
Disengagement under load is probably due to the weakness of the V-shaped
footchange centralizing spring in the kickstaner case, or to a weak footchange
quadrant coil spring. Stretching the spring will cure. Check the cam-barrel
plunger for free movement in its housing.
Footchange Lever
It is sometimes found that the lever sticks. Check for friction between the
footchange shaft and bearing in the kickstaner case cover. Lay the machine over
on its left side and free by using penetrating oil or paraffin; failing this, dismantle
and rub down the shaft with an abrasive. Oil before reassembling. A weak
centralizing spring is betrayed by the same symptoms.
5. THE CLUT~
Clutch Spring Adjustment
Check that the clutch-spring studs are not bent. Insen the spring cups, then
the springs. Fit the nuts, leaving them slack. Ensure that the pressure plate is in
the correct position; tighten the nuts diagonally (top left, bottom right, and so
on). When all nuts are fully tightened, unscrew each four turns. If a slot is cut in the end of a screwdriver, sufficient to clear stud bolts, this modified tool will
facilitate fitting.
Clutch Adjustment: CP-Type Burman Gearboxes

A small adjustment can be made by screwing in or out the clutch~cable
adjusting screw located on the gearbox, leaving free movement at the clutch
lever end of between %~in. to -k-in. If this adjustment is insufficient it will be
necessary to alter the position of the operating-lever fulcrum pin, located within
the kickstarter case, by adjusting the sleeve nut. The effective length of the
clutch push-rod is then too long and can be compensated by means of the
sleeve nut. There should- be *-in. free movement between the operating lever
and the operating plunger. To increase the clearance turn clockwise; to decrease,
turn anti-clockwise (usually about half to one turnl. Check the movement of the
operating lever by inserting a finger in the gearbox fill~r hole. Remember that a
well-lubricated clutch cable is essential to smooth working.
THE CLUTCH I COMPETITION ANO SCRAMBLES MOOELS
6. COMPETITION AND SCRAMBLES MODELS

Trials
In order to obtain good results, i.e., dead-slow running with plenty of power at
slow speeds, use a low compression ratio: 5.8 (500 ce) : 6.3 (350 cc) with standard
cams 11949-53 type) and correct pilot adjustment. If necessary, fit a throttle slide
with -'\--in. less cutaway and eliminate air leaks. Use heavier flywheels and a
manually-operated ignition lever. Flywheels are identical on both 350 cc and 500
cc machines, with the exception of the balance factor, but if the machine is a
standard competition model no alteration is necessary.
Clutch Adjustment: B52-Type Burman Gearboxes
Gear Ratios
The clutch will not disengage if adjustment is incorrect. Reset the operating
mechanism by slackening the cable adjuster as far as it will go. Next, release the
nut in the centre of the pressure plate (use a spark-plug spanner); screw in the
clutch thrust-stud until light contact with the push-rod is felt. Then unscrew the
thrust stud half a turn. Again tighten the nut, noting that the thrust stud must not
move. The clutch cable can now be adjusted until there is %-in. to -'\--in.
movement in the outer casing and the adjuster.
An ultra-low bottom gear is necessary; fit an engine sprocket with 18 teeth (500
ccl : 16 teeth (350 cc). This will do for normal events (see Gearbox Ratios in the
Appendix).
Clutch Cables
To remove the clutch cable, first take off the oil-filler cap on the gearbox; screw
the clutch-cable adjuster fUlly home and, with a suitable lever, press in the
operating lever and release the clutch cable. Withdraw the clutch-cable adjuster
from the gearbox and remove the cable from the handlebar lever.
When refitting the clutch cable see that sharp' bends are avoided.
Clutch Slip
There are many causes. Friction inserts rendered ineffective by oil is the chief
offender. In this case, wash them in petrol and apply fuller's earth, or fit one of
the types of oil-resisting inserts recently marketed. Clutch springs are usually
weakened by heat generated through persistent clutch slip so check for a free
length of l-1--in. Clearance between the clutch-actuating lever and plunger
should be ..Jr-in. Free movement at the handlebar cilltch lever should be %-in. to
+-in. Check that the top of the operating lever in the kickstarter case is not in
contact with the oil-filler plug. The clutch hub-nut on the mainshaft of CP-type
gearboxes sometimes fouls on the spring cups; change for a smaller-sized nut
(852 type).
Chaincase Sealing
Pre-1952 model owners should use a rear-half primary chaincase with a mud
excluder fitted at the mainshaft hole. Use a felt sealing-washer between the back
of the engine sprocket and the crankcase, and fit a length of rubber tubing from
the crankcase release-valve orifice.
Conversions
A great deal of thought should be devoted to converting standard models for
trials. Some of the essentials follow: mudguard clearance must be ample, and the
front guard presents no difficulty in this respect, but the rear mudguard bridge
piece must be raised. Preferably, competition-type guards should be fitted. The
main driving gear and layshaft fixed pinion must be changed to provide the
ultra-low ratios needed for competition work. Competition ratios for the CP box
are obtained with 32 teeth for the main gear and 18 for the meshing layshaft
pinion. For the 852 box, sizes are 30 and 17 respectively. Change the engine
sprocket.
Converted machines may not handle so well as standard competition models
because of the difference in the frame head-lug angle which determines trail or
castor action. The fitting of a 21-in. front wheel helps to offset this difference.
General Tips
Complete Clutch Removal
Remove the chaincase, the clutch screws, springs and cups. and pressure
plate. Turn back the clutch hub-nut lock-washer. Now engage top gear, depress
the rear brake pedal as a locking device and unscrew the hub nut. Remove the
front chain. Ease off the clutch assembly, taking care not to lose the 24 clutch
rollers which will now fall out.
Reve~e the procedure to reassemble; grease the roller bearings when
assembling.
19
Waterproof the H.T. brush holder; seal the contact-breaker cover, but not the
ve~t hole (use Plasticine); fit spare clutch and throttle cables.
Scrambles Models
Maximum engine efficiency is called for and this can only be achieved by
attention to every detail. Polish the sphere of the head and the ports; use 8
compression ratio of 8.3: 1 (500 ccl; 9.5: 1 (350 ccl and fit special cams, marke"
Plugs
Fit plugs with a high heat factor, such as FE 220 or 250 (long reach, for
,light-alloy heads): F 220 or 250 (short reach, for ir~," heads). If a long-reach plug is
used in a short-reach head it will cause damage. A short-reach plug used in a
long-reach head will have the effect of retarding the ignition. Plug points should
be flush with the sphere of the head to obtain the best results. If the standard
plug washer is too deep, use a solid-copper washer cut to width.
SH. Use an open exhaust-pipe system (pre-1956, 48 in. long) and fit a
"Monobloc" or "T.T."-type carburetter, preferably the former. With compression ratios as above, run on premium grade fuels. If higher compression
ratios,are chosen (11 : 1 to 13 : 1), methanol-benzole mixture must be used.
COMPETITION AND SCRAMBLES MODELS
7952-53. Cams marked 1 and 2 (see Fig. 21). Two is used on both
Matchless and AJS.
7954-55. High-lift cams (HL). Cams marked 1,2 and 3 (see Fig. 22). For 350
cc models use No.3 for inlet; No.2 for exhaust. For 500 cc models use No.2
for both valves. When fitting camshafts that have neither a slot nor keyway
for the long shaft, use a No. 1 marking for tht exhaust cam.
Many owners experiment with the valve timing. only to revert to the original. It
is a waste of time, for each tooth represents 20 degrees of the engine rotation, so
that any slight change results in completely different "timing.
Connecting Rods
If there is marking on the top end of one side and the bottom end of the other
side of the piston, the connecting rod needs aligning. It is possible to check the
con-rod without removing it by employing a steel block and mandrel.
F1ywheels
Ught flywheels improve acceleration. Engines made before No. 8,000 had
flywheels which were 25 lb. lighter than at present. Rywheel balance will not be
affected if the periphery (not side) is reduced by % in.
It is sometimes found that the flywheels move on the crankpin, especially in old
models, due mainly to exceptional stresses and strains of scrambling. The
interference fit of the crankpin shaft should therefore be checked. A copper
deposit 0.002 to 0.003 in. on both shanks of the crankpin will produce new
interference-fit dimensions. When crankpin washers are used fit steel in
preference to bronze.
Short-Circuit Racing
As with scrambles models, machine preparation for racing is all-important and
no detail should be ignored. All-round tightness of nuts, bolts, guards, cables,
etc., wheels correctly balanced, correct carburation, correct plugs and a very high
standard of engine efficiency are essential.

Gear ratios must be altered to suit the purpose. On touring machines silencers
can be removed, subject to increasing the main-jet size to 19O<>r 200 (500 cc) and
to 160 or 170 (350 cc). "Monobloc" increases are to 280 (500 cc); 220 (350 cc).
Plugs recommended are KLG FE 220 or 250 (long reach): KLG F 220 or 250 (short
reach).
Valve Timing
All timing pinions and cams are marked and little difficulty should be
experienced in refitting. Cam markings are as follows:
7937-48. Cams marked with a dot. Timing pinion with a line on the outside
face midway in the keyway slot (see Figs. 19 and 20).
7949-57. ,Cams 1 and 2. One is Matchless; two is AJS (see Fig. 211.
Meshing the timing

Pinion and inlet
valve 968(
Second operation in
meshing the timing

pinion and exhaust
valve gear
1949-51 timing a"angement.

dual marked to suit either AJS or
Matchless engines
The method of cam marking has been altered since 1945. The year of
manufacture and type of marking used are as follows:1945-48-Cams are marked with a dot. The pinion has a line on the
outside face midway in the keyway slot.
1949-51-Cams are marked one and two for use on both Matchless and
AJS engines. Number one marks are for Maichless engines, number two for
AJS.
1952-53 (Valve Lift 0.326 in.)-Marking similar to 1950-51 models, with the
exception of assembling, when number two marks are used for both
Matchless and AJS models inlet and exhaust. (Both models have magneto
in front of cylinder at this date.)
1954-55 (Valve Uft 0.362 in.)-Cams are of the high-lift type (marked HL).
Additional figure number three is used for setting inlet timing on the 350-cc
model only. Use number two marks for the 350-cc exhaust and for both
valves of the 500-cc model.
1956-58 (Valve Lift 0.362 in.)-Number three used for the 350-cc inlet,
number two for the 500-cc inlet and number one for the 350-cc and 500-cc
exhaust.
Note- The latest typ~ camshafts do not use a keyed shaft to drive the
magneto. If a keyway is not visible in the cam wheel use No.1 mark for the
exhaust-cam setting, before 1956-57.
20
COMPETITION ANO SCRAMBLES MODELS / TRANSMISSION
Rear Chain Adjustment: Spring Frame
Fitting Cams
The drill is the same for all models:
,
.
(11 Turn the engine until the mark on the pinion is at about 10 a clock ."~Iet
caml. Insert the cam with its mark to registerwi~~ th~ mark on the p,lnlon.
(21 Turn the enginelolWarduntil the mark on the p'nion IS at about 2 a clock
(exhaust caml. Insert cam also with the mark in mesh with the mark on
the pinion.
Lubricate all parts before replacing the timing cover.
Spring-frame Models 1950-54
The rear-wheel spindle carries two cams which, wh~n rota~ed,. alte! the
position of the spindle in the fork-ends. The cams abut agaInst prolectlons In the
fork-ends and the right-hand one with a lock nut is adjustable and is pre-set on
initial assembly. The position of this projection should not be altered unless wheel
alignment is incorrect.
To adjust the rear chain with the machine on a centre stand, slacken the nut
securing the speedometer gearbox and the left side wheel nut. Continue by:
(j) Moving the wheel forward so that the two cams on the axle contact the
projections.
Oil Apply an adjustable spanner to the hexagonal b'!dy o~ the .wryeel a><!e,
keeping the wheel pressed forward, and turn untIl chaIn whIp IS 1 % In.
when tested midway between sprocket centres.
(iiil TIghten the wheel axle nut, turn the wheel and check the c~aon ten.. ~n
in several positions; correct whip is that at the tightest place In the chaIn
.,.
.
travel.
(ivl TIghten the nut securing the speedometer gearbox, posItIoning the drove
cable before finally tightening.
(vi Check brake adjustment.
Rear Chain Adjustment: Rigid Frame

Rigid-frame Models (Machine on Rear Standi
Slacken both axle nuts slightly and the lock-nut on the adjuster bolts.
1954-55 High-lift cams Bre signified by the "
2, 3 marking
7. TRANSMISSION
Front Chain Adjustment
To adjust the front chain, first remove the inspection cap. Follow this by:
(j) Slackening the nut on the gearbox top fixing bolt.
(iii Slackening the forward nut on the chain adjuster about three t~rn~.
(iiil Tightening slowly the rear nut on the chain adjuster until the chaIn IS
tight.
'.
(ivl Slackening ~y about three turns the rear nut on the chain adjuster.
(v) TIghtening slowly the forWard adjusting nut to give a %-in. chain whip
at the tightest point of the chain run.
(vii TIghten the rear nut to lock the assembly.
(viii TIghten the gearbox top fixing bolt and replace the inspection cap.
Note:
21
Altering the position of the gearbox will affect rear chain adjustment.
To adjust the chain
(j) Screw-in equally the two adjuster bolts until chain whip is % in . to % In.
in the tightest place. Check the chain at more than one pOInt.
(iii TIghten the axle nuts.
(iiil TIghten the adjuster locknuts.
Q-O Wheel Models

Follow details given for rigid-frame models but also slacken the nut securing
the brake drum to the fork-end as well as both the axle nuts.
Chain Lubrication
The most effective method, particularly during winter, is to remove the che!n
and wash it in paraffin. A small quantity of "Mobilgrease No.2", "Esso" flUId
grease, "Castrolease" graphited grease, or "Energrease A.O" .should be u~ ~
a bath. Put the grease in a tin and heat it until ju~ fluid; im~erse the. chaon ~n
reheat grease (the chain will cool the greasel, leaVIng the chaIn to soak, then WIpe
off surplus and refit.
Teledraulic Front Forks 1945 to 1955

Other than periodically checking the oil content, this part of the machine does
not need frequent attention.
If the fork motion becomes stiff, and provided that the fork sliders or main
tubes are not bent by impact, the trouble is due to swelling of the plastic bushes.
To remedy, remove the sliders and take off the plastic bushes. With emery
cloth ease down the bore of the bush until it is a sliding fit. Apply oil or a little
graphite compound and reassemble.
A scraping noise as the forks move is caused by the springs rubbing against the
cover tubes. Grease applied to each fork spring will have the desired effect. A
rattle in the forks may be due to a disconnected damper rod or insufficient oil
content.
To Remove the Fork Assembly

Before dismantling, a study of the construction should be made. Remove:
Ii) The wheel, front mudguard and stand.
(ii) The speedometer drive, the bulb holder and the speedometer head.
(iii) The switch panel from the headlamp and the headlamp.
(iv) The handlebars, with fittings; detach brake cable from forks. (Put an old
coat on the petrol tank to prevent damage by the handlebars.)
(v) The two bolts in the handlebar lug for the fork tube and disconnect
both damper rods, if fitted.
(vi) The dome and lock nut from the steering column.
(vii) Tap the handlebar lug upwards until it is free of the fork stem. Take out
the top "frame race, the 28 balls from the bearing and then withdraw the
assembly. A further 28 balls are used in the bottom frame race.
Assembly
Pack the fork crown race with grease and fill with the 28 balls, pass the steering
column through the frame and reverse the dismantling procedure.
8. FORKS AND FRAMES
~.
FORKS AND FRAMES
hook spanner first unscrew the slider extension and follow this by:
Ii) Removing the front wheel, mudguard and stand.
(ii) Detaching the brake cable.
(iii) Unscrewing the bolts in the handlebar lug.
(iv) Detaching the damper rods, if fitted.
(v) With a sharp downward movement withdrawing the slider (warming the
enlarged top end of the slider will facilitate removal).
To remove the damper rod and tube a thin-wall box key, fashioned to enter the
recess in the bottom of the slider, is required.
To Refit
With the damper rod and tube assembled in the slider, operations are:
Ii) Pass the damper rod up the fork tube and raise the slider until it meets
the oil seal.

(ii) Warm the enlarged end of the slider and press in the oil seal sufficiently
to allow engagement of the screwed extension.
(iii) Reassemble in the reverse order for dismantling and finally tighten the
screwed extension when the wheel is refitted. A length of copper wire,
or an old push-rod screwed on to rod, can be used to lift up the damper
rods for attachment.
To Remove Fork Inner Tubes

Both fork tubes can be removed with the sliders attached, but a draw-bolt to
pull up the tubes will be required.
Without this tool, first remove the fork sliders as previously described. Release
the two screws or bolts clamping the fork tubes from the fork crown and pull out
the tubes from the fork crown and handlebar lug.
Rear Suspension
The swinging-arm is hinged behind the gearbox on two robust self-lubricating
bronze bushes. There is a reservoir for oil incorporated in the swinging-arm.
To lubricate, remove the screw in the right-hand cap and use a heavy gear oil;
normal content 1 % fluid ounces. (6'J ... l.)
Wear on the bushes is only likely to take place after the machine has covered
considerable mileage.
Fork Sliders
"Teledraulic" fork sliders comprise the light-alloy moving members of the fork
assembly, carrying the front-wheel spindle, mudguard, brake anchorage and,
most important, housing the damper mechanism. Modifications have been made
to the detail working of this mechanism over the years since "Teledraulics" were
first introduced early in the war, but the fundamental principle has remained.
"Teledraulic" operation depends on the action of disc-type damper valves with
limited permitted movement, or orifice cut-aways, designed to obstruct
progressively the transfer of hydraulic fluid from one compartment to another
during the movement of the slider under running conditions and, thereby, to
damp, or slow down, slider movement at both the impact and rebound phases.
To remove one or both sliders raise the front wheel clear of the ground. With a
Rear Suspension Units

The normal oil content is 3 fluid ounces (85 cc) S.A.E. 20 oil.
To change the oil, deal with one unit at a time and remove it from the frame. A
clamp to grip and encircle the outer tube is needed and is applied close to the
bottom pivot lug.
With the clamp gripped in a vice, slacken the bottom pivot lug. Turn the ",nit
upside down and remove the bottom pivot lug.
Take hold of the exposed damper tube and work it up and down, then pour the
oil content into a graduated measure, and allow the unit to drain. Pour back the
specified amount of oil and reassemble in the reverse order.
22
FORK AND FRAMES
FIG 23
FIG 24
General arrangement of forks on
the 1948-50 models. No brake

anchor stud is featured. Crown
design is also different
23
Genera/arrangement drawing of Te/edraulic 'ront fork used

on the WD G3L. Note the brskeanchor stud and bolts for the
bottom crown clamps
FIG 25
An exploded impression of the Matchless "TeledrauJic" front fork

arrangement - one of very few enterprising developments/aunched
by II motorcycle manufacturer in time of war lind retained for peace
production. Bottom crown clamping ;s by studs and nuts
eJ
FORK AND~FRAMES
-Tt:U:ORAUUC FRONT FORK CeNTRE TUBe: A$Sf:MBLY
W/41 1G3L!fF2OI.
FIG 27
(Above) Details of the assembly
order of the WD G3L TeledrauJic
front forks
FIG 26
General a"angement of forks on a/l
models ex.cept 1948-50. Cap head
socket screws clamp the bottom
crown on the stanchions. Top crown

features a speedometer mounting
cutaway with tapped thread
o,
I
FIG 28
fRight) on movement in the WD
fork, recoil on the left, bump on the
right
.JT
"'"
iORKS AND FRAMES / WHEEL BEARINGS
To Grease or Change the Unit Springs
9. WHEEL BEARINGS
Apply a clamp on the .outer tube cl~se to .the

bottom pivot lug and gnp the clamp In a vIce.
Unscrew the ring nut which is below the bottom
cover tube. Slacken' the lower pivot lug, take the
clamp out of the vice, then turn the unit upside
down.
Take off the clamp, the bottom pivot lug and the
bottom cover tube; when the spring can be removed.
On models made after 1953 a circlip is used in
place of the ring nut.
Dismantling this type of unit is a two-handed task;
the help of a second person is needed to compress
the spring to extract the circlip.
T0 r~assemble reverse the dismantling instructions.
. Wheel bearings are of the taper-roller type. They have a fixed location on one
side, the other being adjustable. The fixed location has a circlip in a groove cut in
one end of the hub shell; the adjustable location. is by a screwed ring, threaded
into the hub, and a locking ring. The rear-wheel adjusting ring is at the left side of
the hub and on the front wheel at the right. When adjusting ensure that there is a
little end-te-end play - about O.OO2-in. The maximum rock of the wheel in
.
position should be not more than -/O--in. at the rim.
To adjust the rear wheel remove it from the frame. The front wheel can be dealt
with in situ. A recommended drill is first to slacken the locking ring after which
tighten the adjusting ring until all slackness has peen taken up and then slacken
back the adjusting ring half a turn. Now tighten the locking ring, seeing that the
adjusting ring does not move.
Front Wheel Bearings
Steering Head
Remove nuts and brake cover plate compl!U,e. Slacken Fig 32's locking ring
(11). Unscrew the adjusting ring fully (10) and remove wit~ locking ring. (11) in
situ. Apply firm pressure to the threaded end of the spindle, so removing from the,
other end the cup housing (9) for the oil seal, the oil seal itself, the metal washer (7)
behind the oil seal and then the outer cap. The front wheel spindle (6), with two
sets of rollers, may now be removed from the hub.
To check for correct adjustment take the weight

off the front wheel by placing a support beneath the
frame or footrests. Place one hand under the front
guard and the other on the steering head and check
for movement, or attempt to obtain movement,
lifting upward and forward. If slackness is discerned,
adjust as follows:
Slacken the nuts on the fork-crown studs and the
nut above the steering column. TIghten the hexagon
beneath the dome nut and again check for
movement. Repeat this tightening-up drill until no
"shake" is discernible and the fork assembly rotates
freely. When satisfied that adjustment is correct
tighten down the dome nut and the fork-crown stud
nuts or screw. If a steering dampe, is fitted it should
be quite slack during this work.
FIG 32
A works tool employed to grip

the upper slider member for
dismantling
FIG 30
t::Jj
FIG 29
A cut-away impression
of the damper tube and
damper rod assembly
25
FIG 31
The
tube
assembly
V:////n,;:'" and rebound
Post-war layoutofwheeJ bearings showing (top) the front-wheel assembly and (bottom} rear hub
components for spring-frame models
.
.
.
MATCHLESS SINGLES
1939-1~
Two types of thrust-pad adjustment used to compensate for

brake-lining wear.
Rear Wheel Bearings

In spring-frame models remove brake cover plate, brake shoes, centre spindle
with cams, bushes, spacers, nut and speedometer gearbox. Remove the lock nut
(see Fig 32's lower part) (26) on the left-hand side and unscrew the adjusting ring
(2!;) completely, removing this with the lock nut in situ (26).
At th~ fixed location end, press the visible washer, so pushing out the assembly
at the other end - the cup housing (24) for the oil seal, the oH seal itself (23) and
the metal washer behind it (22), the spacing ring (21) between the metal washer
and taper bearing, and then the outer cup (20).
..
- Remove the roller cage (26), centre spacer (19) and rollers in the cage (18).
At t~e fixed location end, having applied pressure on the visible washer and
removed the circlip (12), apply pwssure with a suitable tOOl. through the open end
of the hub, on the inner edge of the outer cup (18) and so force out the oil-seal,
plain washer (13), the oil seal (14).with its encircling spacer collar (15), the oil-seal
internal plain washer (16), and the spacing ring (17) between the metal washer
, and the taper bearing. Take out the cup (18).
To reassemble, reverse
. the above procedure.
At the fixed location end exert pressure on the visible washer, so pushing the
whole assembly farther inJo the hub. Remove the circlip (1). Reverse the hub and
press on the inside edge ofthe outer cup (6), forcing it out of the hub. It will bring _
with it an external oil-seal plain washer (2), the oil seal (3) with encircling spacer
collar (4), and the oil-seal inner plain washer (5) and the cup (6).
To reassemble, .reverse the above procedure.
WHEEL BEARINGS / BRAKES / DYNAMOS
FIG 33
,If this adjustment is ineffective, slightly enlarge the hole in the cover plate and
repeat the process.
'Water in Brakes
Brake lining!lwnich are not affected by water to any considerable extent are
a&leilable for machines made after 1947. The use of a thin steel washer behind the
rear cover plate will allow water to escape and thus ensure that the brake is
unaffected.
'10. FRQNT AND REAR BRAKE,'ADJUsTMENT
-.
Brake adjustmen't to comp~nsate lor lining wear is made by finger adjustment

on the rear brake. rod pnd the front'brake cable adjuster. When excessive
movement deyel~ps ii can be taken up by adjusting the position of the thrust
pads fitted to 'each brake shoe.
Where steel brake shoes are used, the collar 'position can be varied as the slots
machined in it are of a different depth"
..
,With alloy brake shoes, washers are used under the head of the steel thrust
pins. .
'..
.
.
Centralizing Brakll' Shoes

In 'order, that both shoes contact the.(llrake drum simultaneously and to
remedy a ".spongy effect", release the nut securiMg the brake cover plate and
apply pressure o~, the brake pedal, or handlebar lever, depending upon which
brake is being dealt with. Maint~in this pressure and retighten firmly the brake
cover nut. The brake adjustment can be closed up considerably to improve brake
efficiehcy.'
.
11. DYNAMOS
t'~
Two types of dynamo were fitted. 1939-49: E3AR/A05/1, with negati~",arth;

1950-55: E3-N, with positive earth. The later (longer) type can be fitted t&earlier
models if the kickstarter case is exchanged. Some W.O. machines used Miller
equipment, some Lucas.
Dynamo Chain
To adjust the chain, remove the inspection cap (front chaincase), unscrew the
dynamo clamp bolt, turn the dynamo with a spanner engaged on flats on the left
side of the component. There should be %-in. chain whip. Check through the
i"spection cover hole. Th~ armature shaft is eccentric to~he body of the dynamo,
therefore, to tighten the chain the dynamo should be turned anticlockwise; to
slacken it, turn the dynamo clockwise.
Screw' up the dynamo clamp bolt and re-check. Use this opportunity to check
the oil level in the chaincase.
26
Magneto Chain
To adjust, remove the chain case; slacken the nuts on the magneto platform
bolts, insert a lever beneath the end of the platform .and prise upwards until the
chain whip is I'-in.; tighten nuts and re-check. Do not forget to grease tile chain
well before replacing the case.
Removing Dynamo
For all Models before 1953
Remove the front chaincase, clutch, engine sprocket, circlip lockwasher,
dynamo sprocket and the rear section of the chaincase. Remove cables, slacken
clamp bolts. Take out the dynamo from the drive side of the engine. Instructions
for dismantling are given in the previous chapter.
DYNAMOS / ELECTRICAL EQUIPMENT
12. ELECTRICAL EQUIPMENT

Ignition, 1945-55
Many models have the Lucas type NI-4 magneto. Competition models
have the racing NRI magneto with a manual ignition control. 1954-55 models are
fotted with A.T.D. units, and feature the SRI magneto with rotating magnets.
Where A.T.D. units are standard, a wedge placed between the moving part of
the unit and the stop holds the setting in a fully advanced position.
Removing Contact Breaker, Nl-4 Magneto

Move aside the swivel blade retaining the contact-breaker cover. Take off the
cover and the screw and spring washer securing the spring blade and backing
spring. Remove the screw and fibre bush. Straighten the lockwasher under the
centre screw retaining the contact breaker and ease off the assembly. When
reassembling lubricate the wick with oil.
Contact Points
A special abrasive strip is available for cleaning the contact points. It may be
necessary to reface pitted points by using a fine Carborundum stone. If the points
are found repeatedly to be burnt, a faulty condenser is usually the cause.
Cleaning Contact Breaker Points

Turn the engine shaft until the points are fully open, clean and check for the
correct gap (0.010 to 0.012 in.). To reset the gap, slacken the locknut, set the
required gap and tighten the locknut.
SRl Contact Points

Removal of the dynamo on post 1953 models. In earlier years it was necessary
first to take away the gearbox outer cover
For all Models after 1953

Remove the chaincase, the spring circlip and locking plate from the dynamo
shaft nut, and with a spanner engaged with the flats at the back of the dynamo
sprocket, unscrew the sprocket nut. Place a suitable wedge between the
sprocket and the dynamo body when a few gentle taps on the wedge will push
off the sprocket without damage to the armature. Remove cables. Turn the
dynamo until the locating strip is in line with the keyway in the engine plate. Take
away the dynamo from the timing side of the engine, tilting it upwards to clear
the gearbox casing.
To refit, reverse the above procedure. Carefully check the position of the
locking plate and circlip after the armature nut has been tightened.
27
Remove the moulded cover; slacken the nut securing the end of the
contact-breaker spring and take off the contact-breaker lever. To adjust, loosen
the two screws holding the fixed contact plate and alter the position of the plate
until the required gap is obtained.
Dynamo
To test the dynamo while it is on the machine, remove the "0" and "F" cables
from the dynamo and connect the two terminals with wire. Run the engine at
idling speed and connect the positive lead of a movingcoil voltmeter (calibrated
for not less than ()'10 volts) to either of the two dynamo terminals and jink the
negative lead with a good earth point. Slowly increase the engine speed, when
the voltmeter reading should rise rapidly and steadily. Do not allow the voltmeter
reading to exceed 10V and do not rev up the engine in order to obtain greater
continued on page 34
MATCHLESS SINGLES 1939-l955
earing an illustrious designation. the G3L is featured here by way of a maker's definitive
photograph prior to factory retouching for the 1953 catalogue. Loaned by CQurtesy of
Motorcycle Sport. the picture shows the 350 fitted with the Bunnan BS2 box which superseded
the earlier pre-1952 CP type. On the CP box the primary chaincase clutch dome was plain. on
the 852 it had the small detachable cover shown here, and on the April 1957-00 AMC box there
was a large chainwheel-sized cover.
Roadsters gained futl-width front hubs from September 1953; the full-width rear hub came in
12 months later. Here are seen the offset-brake types.
Motor is light-alloy head with iron barrel. AJS front-mounted magneto. pre-MaRobloc
carburetter (Monoblocs arrived in 1955 on AJS and Matchless), and the saddle could be of
The 1953 Matchless 350 cc G3L
Lycetts or Terry manufacture. Twin seats were never offered on rigid roadsters.
Centre stands were used on springers only but a prop stand was an optional extra on all. The
speedometer is mounted a'top the Teledraulics' upper crown. prior to later integration inside the
head lamp shell.
A Lucas 6volt dynamo. driven by a separate short chain from the back of the engine sprocket,
is featured. The Lucas alternator (springers only) was introduced for the 1958 season complete
with a cast-alloy chaincase to replace the pressed'steel type shown here.
The final year of the G3L was 1955. it being lapsed in August of that year. the
already-catalogued G3LS springer holding sole sway in the lists - REG HIDE
,
28
The 1949 Matchless SOO cc G80C

hown here in the final year oflhe rigid rear end-only, the GBOC did not take swingingarm rear
suspension until 1950 when it b~ame known as the GSOCS (5 for Springed, with the rigid
GSOC continuing as an inconsequential option right through to August 1955. The first springers
had slim-type AMC candle legs though these were soon replaced by the Jampot variety.
A GSOS springer however was offered for export-only in 1949.
The GSOC shown here has iron head. The engine and frame numbers commenced with 451 C
and 467C respectively in 1946 and then continued 474C and 576C for 1947, SS7C and 978C for
1948, 700c and 1S47Cfor 1949 and 900C and 210SC for 1950 when the new Iightalloy head and
short wheelbase frame were introduced.
Magneto position on Matchless versions of the AMC singles was behind the cylinder until
September 1951 (961C and 2694C) when the l.xJcas instrument was moved to the familiar AJS
29
Maker's definitive photographs by

courtesy of Motorcycle Sport
site in front of the engine. In 1952 (t096C and 3218C) a new front brake was fitted from
September of that year for the t 953 season.
A twin seat - GSOS only - was not offered on the 500 singles until September t 952, the term
dualseat (one word and coined by Feridax) being avoided by AMC - REG HIDE

!
;.
MATCHLESS
Ltr

courtesy of Motorcycle Sport
The 1959 350 cc Matchless G3C Trials

n the hands of such maestri as Gordon Jackson and Hugh Viney. the AlS/Matchless trials type
gained innumerable postwar competition successes, paralleled on the scrambles side by Dave
Curtis and others on the Matchless GSO.series. The version shown here is for the 1959 season
when it became known as the Matchless G3C Trials instead of the G3LC as hitherto. This
maker's definitive photograph is not of course strictly within the ambit of this book but being to
hand is too important not to include. To many it will represent the culmination of the art of the
British big fourstroke trials machine with its accent on plank.

The G3C Trials. with the AMC gearbox. had a new frame giving 3-inches more ground
clearance in September 1956 (frame number 7350-on). The following year saw a wider rear
mudguard (7952on). In September 1958 there came a shorter and lighter frame (8490-on).
Girling swinging-fork rear suspension was standard. the units having the clevis lower ends
unique to AMC and on the trials machines inclined forward at the top. whereas on the roadsters
they were vertical.
Note the tall motor for a 350. the small unchromed tank. Lucas wader magneto. Dunlop
saddle, fork-mounted speedometer. cylindrical toolbox below the carburetter and the absence of
an airc1eaner - REG HIDE
, H.
350 cc MODEL 41-G3L
w.o.
,
iI
I
The WD Matchless 350 cc G3L

pecially drawn for OMS Ltd by artist Stephen Ruffle, this War Department WD-G3L is a
composite of authentic features as found on definitive photographs of the era. The military
insignia are genuine though the wartime date is unknown.
TechnicaJ specification ofthe WD models varied. The most dramatic switch was from girder front
forks of the WD-G3 (as that version was known) to the AMC own-brand Teledraulic forks of the
WD-G3L. Other changes included Lucas or Miller electrics. two different methods of mounting the
main footrests (the inboard rests required an exhaust pipe with a more marked kink than the type
shown here), rear lights. rear lifting handles. and the make of pillion seat (when fitted).
Wartime blackout masks on the headJamp were of course in common usc. We have traced three different styles of mudguarding and there may have been more.
Matchless were easily the most popular with Don-R servicemen as the marque was the first
production machine to be equipped with a telescopic fork. They were also probably the second most
numerous though the BSA SOO cc sidevalve M20 - with 126,334 put into Armed Forces service
between 1940 and 1945 - was certainly top of the numbers league. Nor was the Matchless the only
31
ohv single in War

Department use; AIS (very rare),
BSA (equally rare hairpin-valve-spring
B30). Royal Enfield (CO), Triumph (3HW) and
Velocette (MAF) all supplied such types though none
of these equalled the 350 cc Ariel WNO ohv single in numbers.
At the outbreak of war. 3 September 1939. the British forces had 21.000 service machines and
6,000 of these were impressed civilian models of many makes and sometimes very up-tbe-market
types_ Some 425,000 WD machines of all makes were built during the war and 270,000 were in
service on VE day.
Few Don-R's would quarrel with the claim that it is the Matchless G3L that is remembered with
the greatest affection - REG HIDE
ith its all-iron overhead-valve single-cylinder engine, the AMC-made Matchless G80 was
unchanged postwar until September 1950 when the 19SJ-season models took a die-cast
light-alloy cylinder bead. an increased compression ratio and a new clutch.
As with AMC practice. the engine number (stamped on the driveside crankcase immediately
under the cylinder) gave the last two digits of the year of manufacture. an oblique stroke. the
model designation, another oblique stroke. and then the actual engine number. Thus the 1949
680. commencing with 9000, would be 49/080/9000 ..
The frame number that year commenced at 35000 and was stamped on the head lug casting.
Though not roadtested - this being against the maker's policy to allow the specialist press to
evaluate their products- the G80's top speed was traditionaUy in the mid-SO's and performance
The 1949 500 cc Matchless G80

courtesy of Motorcycle Sport.
was reckoned as being brisk for the engine specification on the Pool petrol of those days. The
7inch diameter brakes, as with the later fullwidth huh, was always felt to be borderline for the
potential of the machine - REG HIDE
32
ELECTRICAL EQUIPMENT
WIRING QIAc'RAM
f"OB
pR. QYNAMO
WITH
72.."". H9. LAMP.
"'ON
CUT-OUT AND
"tGUL""Of\ UNIT
INOICATt~
gARTH
t.UlB HqLDE~ ('OI1TAtTS
OR F"RAME ('ONHEqlC!!
RE:CULATOR
Qy6
OVNAMO
,- .......,..-._.w...-.
1_&_.&
._..- ._-_.-.... __
.--._u
1 __ _
I n TO C .. '"
COLO""
.. _",.,..u
J III. . . I'tU.OW
I,_I&C_
lI_mlA_"
II
_ _ lit
t ..... . . -
1ILLOW .....111
'I'IUOW&'-
"01 ftU.OW"_"
...
u.ow .. __
'I'IUOW"
II
IUU'U
11_ ORt N9 1365

f..l MllL[R,sC L....
FIG 35 Wiring diagram for the Miller equipment found on some WD

Matchless machines
33
....... _ 1
..
"".U'
_.&-.~.
,. "'UI .. G.....
.._
'nit
D _
,,~
It lUll
PIMI'U
UWWlI&_.
CIlCUT" _
..... _
...., _ L ,
c.tM.l " _ U . _ _n
'''TI~GlAM.
FIG 36 The Lucas wiring diagram for the WD G3L so equipped features
minor departures from that suitable for lattH civilian roadsters
FIG 37
HEADLAMP
SIDElAMP
SIOtlAHP
ELECTRICAL EQUIPMENT
SPHDOHETER
011'1'11.
SWITCH
PUSH
MAGNETO
HORN
HORN PUSH
DYNAMO
DYNAMO
TAIL LAMP
.. ORN
SNAP
CONNECTOR
TAll LAMP
1952-55 positive earth system. Note: Use one lead for pilot when twin side lamps are not fitted
FIG 38
Both WD and civHian roadsters to 1951 operated on the negative earth system. This can easily be
transposed to positive earth and the dynamo polarity readily reversed
voltage - one-eighth throttle is considered sufficient and, if the above reading is
obtained, the dynamo is in order.
If there is no reading, check the brushes. If there is a reading of about 1 Y, to 2
V only, the armature winding may be faulty. It may be necessary to remove the
dynamo. For dynamo removal procedure see pageV.lf a reading of about Y, V is
obtained, the field winding may be at fault. It is recommended that if an overhaul
is necessary the services' of the dynamo manufacturer should be sought.
Both W.O. and civilian roadsters to 1951 operated on the negative earth
system. This can easily be transposed to positive earth and the dynamo polarity
readily reversed.
34
Compensated Voltage Control Unit

The regulator is set to maintain a predetermined generator output at all speeds
and controls the flow to the battery. The rate of charging is at its maximum when
the battery is at lowest ebb, and at minimum when the battery is fully, or almost
fully, charged.
When the battery is in good condition the dynamo gives a trickle charge and an
ammeter reading of about 1 to 2 amp. The cut-out is an automatic switch
connecting the dynamo and the battery. When the engine is running fast enough
to cause the voltage of the dynamo output to exceed that of the battery, the
cut-out links up the battery for charging. When engine speed is low or the engine
not running, the cut-out disconnects the battery from the dynamo, so preventing
the battery discharging through the brushes and commutator. If, under normal
running conditions, the battery is continually in a low state of charge, or is being
overcharged, then the regulator setting should be adjusted at a Lucas Service
Station. The C.V.C. unit is marked with the letters "F", "A", "0" and "E". "E" is
earthed, "A" is connected to the ammeter and #IF" and "0" pair with markings
"F" and "0" on the dynamo.
It pays to use the services of an expert, so do not yourself meddle with the
C.V.C. settings and cut-out contacts.
13. EX-W.D. MODEL 350cc 41-G3L

Army models were first manufactured in 1939 and were similar to the 1939
civilian models. These machines are also similar to the 1945 models; with the
exception that girder instead of "Teledraulic" forks were fitted. Instructions for
fork servicing, overhauling and reassembling, therefore, have wide application.
"Teledraulic" forks can be fitted to girder-fork models, the front frame layout
being similar. The changeover necessitates the speedometer drive from the front
wheel being discarded and transferred to the rear wheel, as on later models fitted
with "Teledraulic" forks. This work involves the rear hub being machined. Two
slots are cut in the face of the hub tube to drive the speedometer gearbox. If good
workshop facilities are not available the owner is advised to purchase a
second-hand ex-W.O. wheel. An alternative method is to make an adapter. The
FIG 39
---
_ .L_
--~
I
I
35
Speedometer drive. Adapter de-
tal7s for modification of a 1939

model for "Teledr8ulic" front
suspension
ELECTRICAL EQUIPMENT / EXWD. MODEL 350 cc 4TG3L
hollow spindle must be reversed to permit the wheel to be bolted to the brake
drum, as on civilian models. Note that the quickly detachable method cannot be
used when the speedometer drive is modified in this way. A new rear wheel and a
solid spindle with distance piece, speedometer drive and cable are required to
complete the conversion.
The near-side fork slider anchoring the front brake can be exchanged for a later
type if W.O. "Teledraulic" forks are used; alternatively, modify the front-brake
anchorage, employing the front mudguard fixing bolts for this purpose. W.O.
models were purposely detuned by a reduction of the compression ratio to 5.B,
effected by a T-in. compression plate between the cylinder and crankcase. A
l{,-in.-bore carburetter was standard.
Gear ratios (1941) provided for a low bottom ratio, similar to that on the
post-war competition machines. An improved valve timing was introduced on
engines after No. 54512. Owners of 1941 models can convert their machines, if
they are in the original form, to the civilian counterpart by the following
procedure:
Remove the compression plate, then machine away the ridge in the cylinder
barrel at the limit of the piston-ring travel. Steel washers T-in. thick for push-rod
tubes can be dispensed with. Fit the later-type carburetter with bore size l-in., the
inlet port being enlarged to match the carburetter; this applies also to the
distance piece. Change the main driving gear and layshaft fixed pinion for similar
gears of the standard type (30120) teeth.
Engine efficiency can be further increased by fitting post-war high-lift cams,
provided that the valve-lifter shaft is dealt with as described in an earlier chapter
and by taking care to check the valve motion as a precaution against the valve
springs closing up or being coil-bound when the valves are at full lift.
If it is desired to use a machine for scramble-type events, the following
modifications will be found useful:
Discard the timing-side roller bearing and use a double-diameter bronze bush,
obtainable from the makers. Modify the flywheels to take a l{,-in.-diameter
crankpin, assuming the engine is fitted with the earlier-type %-in. shaft. Fit the
shortertype 1947-55 connecting rod and use a high-compression piston of 9.5: 1
ratio. Discard the compression plate and steel washer for push-rod cover tubes
(-.\--in. thick).
Fit 1948-type valve springs, top collars and an exhaust pipe of 1 %in. diameter,
48-in. long. Also enlarge the inlet port to 1 or 1 T-in. and use a carburetter to
match.
If workshop facilities are available, modify to use an inlet valve -/r -in. larger in
diameter than standard. The valve seat should be made approximately -/r-in. wide
and a cutter used to reduce valve-seat width. With this arrangement, check the
valve motion and ensure that the valve head does not foul the cylinder barrel
when the valve is at full lift. The application of a half-round file to the cylinder
barrel at the point of contact will provide the necessary clearance.
The inlet-valve guide can be made of bronze with a bore of -I.- -in. for the inlet
valve instead of the normal %-in. The exhaust-valve stem diameter should not be
reduced. Exhaust-valve material is KE 965.
An excess of oil in the combustion chamber will affect engine performance,
and the reader's attention is drawn to the procedure for reducing oil supply to this
part of the engine in the chapter dealing with 1945-55 models, with particular
MATCHLESS SINGLES 1939- 1955
attention to 1947 models, iron heads.

If at any time the oil-pump plunger and timing-side shaft is changed, care
should be taken to ensure that the new parts are of the correct type. In 1947 a
two-start pump was introduced; it can be identified by the marking 25 on the
oil-pump shaft end and by 25 marked"on the timing-side shaft worm. The new
parts will not interchange with the old. To adapt the new pump and timing-side
shaft in ex-W.O. models, it will be necessary to fit a %-in.-diameter oil-return pipe
and enlarge the oil-return passage in the crankcase.
To improve braking efficiency - provided that expense is not important 7-in.-diameter brake parts (1948 type) can be fitted to front and rear wheels, the
brake anchor on the front wheel being modified to fit on to the top lugs.
If a prop stand is inclined to bend, or the stop fails, the fault may be due to
wear in the lug in the frame on which the prop stand pivots. Ream out the lug
hole and insert a thin steel bush.
Dismantling Wheel Bearings
Remove the cover plate and brake shoes. When dealing with the rear wheel
take out the centre spindle and remove the speedometer drive complete. Remove
the locking ring and unscrew the adjusting ring. Remove the adjusting ring,
locking ring, dished steel waSher, oil seal and plain steel washer. Turning to the
other end, remove the spring ring, plain steel washer, oil seal with spacing collar,
plain steel washer and spindle, complete with rollers and cages and one outer
cup. Press out the hub shell from the other end, leaving the outer bearing cup in
position.
VALVE TIMING
ABRIDGED DATA
Early Hodels:
Inlet opens befete T.O.C. lOO'
Inlet doses .reer B.D.C. 67
Exhaust opens before B.D.C. 78'
ExMust closes .reer T.D.C. 2S"
Combinations
The 41-G3L is suitable for conversion for sidecar work. The wheels, frame and
forks are similar to those used on the 1945500 cc machines. Fit a 16-tooth engine
sprocket, stronger front springs, sidecar-type 951154 12Yo-in. long. Also fit a
steering damper and use a lightweight sidecar.
A cylinder-head "steady stay" can be used to damp down the effect of engine
torque. The parts can be obtained from the makers and include, apart from the
"steady stays" and clip, a special bolt with extended thread to accommodate one
end of the stay. When servicing the engine ensure that the hardened valve-end
caps, used on all engines up to 1948, are not dislodged when refitting the rocker
box.
EXW.O. MODEL 350 co 41-G3L
ENGINE
Cylinder 80... t
2.7187 in. .0005 in. Rebore to + .020 In
when wear :xceeds .008 in.
Small.En" Bush!
i in. +.0005 in.
.00025 in.
Crankpln Diameterl
1.20325 in. 11.20350 in.
BJ.,.&d Ey. (lID):
1.70J7S/1.70400 in.
Rocker SpiDdle lu.hes:
in. + .001 in.
En,ines numben4 545t2 onward.:

Inlet open. before T.O.C. 32"
Inlet closet al'cer B.O.C. 63"
Exhaust opens before B.D.C. 65"
Exhaust closes after T.O.C. ~
(Set with .016 in. tappet durante.)
Centact......ker Gap :
.010/.012 in.
I,ftldon Advance (with lever control fully

adyanced)
in.
Sparldn,.."", Gap:
.DlO/.025 in.
Wheel Alignment
To check wheel alignment use a straight wooden batten, raised about 4-in.
from the ground; adjust until the batten touches each tyre at both sides of the
wheel centres. Alternatively, use a length of string, tightly stretched. If tyre sizes
are unequal, balance the gap between the batten and the front tyre.
Wheel Bearings
Rocke .. Spindle Sleeve:

.6230 In.,.61lS in.
Cam.haft IUlh.. :
.0005 in.
in.
Timln, Side Hain.hart lush:

~ in. +.00125 in.
Gud,eon Pin:
i in. - .0015{.01)1 in.
Pi.ton Diameters:
.0005 in,
Second Land. 2.6962 in. .0005 In.
Third Land. 1.6961 .0005 ia.
Top Skirt. 1.7131 .0005 In.
Bottom Skirt. 2.7143 .0005 in.
Top Land. 2.6877
Wheel bearings are of the taper-roller type; the inner races and rollers are
integral with the wheel spindle, the outer cups being a pressed hub shell. At one
end is an adjustable location, the other end being fixed. Each roller bearing has an
oil sealing ring and, where a felt washer is fitted, this should be changed to the
later-type rubber sealing ring.
To adjust, rotate the ring screwed into the hub shell and secure it by means of
the locking ring. Rear-wheel adjustment is made from the brake side with the
wheel removed, and on the front wheel from the right-hand side with the wheel in
situ. The amount of end-play in these bearings is 0.002 in., and if adjusted too
tightly damaged bearings will result. Tighten the adjusting ring until movement is
not discernible, then slacken half a turn. When tightening the locking ring ensure
that the adjusting ring does not move.
CARBURATION
Amal type 275/1J with 110 main jet. 5 x 5
throttle ,lid. and n dl. in third or fourth
notch.
PisCOn Rinp 1
Compression (2) 2 DIn X ~, in.
Sc:rJiper (1)
2 A /n x, in.
Gap:
.G06/.008 in. normal.
Hu:imum .030 in.
Valve Stems;
.375 - .0035/.0045 in.
Valve Guides: (I/O)

in.
.0005 in.
Gearbox:
Hainshaft, o .... r-alll.n'th 10.25 in.
Hain sleeye-,ear laarin,. bore 1'/ in. X 010
62 mm. X 16 mm.
Bearin, in end cover, bore 12 mm. X 0;0 .fO mm.
x 17 mm.
Ratios, 5.B. 7.5. 12.2 and 1S.5: 1.
Transmissloft:
Clutch thrust rod, 91 in.
Operatin, lev.r cI.arance (in ,nrbox)
" In.
Sprockets:
Cluh 40T for ... n. X .305"n. chain.
En,ine1ST for rin. X .305-in. chain.
Gearbox 16T for ",in. x .38CMn chain
Rear wheel <llT for I.in. x .lIO-in. chain.
Spok.. :
Front left. 58 in. SG x 10G buttecl.
.. ri,ht,'. in. 9G x 11G butted.
Rear left, 8A In. 6G X 9G butted
.. ri,he, 8& in. 6G x 9G butted.
36
TECHNICAL DATA 1945-47
GEARBOX INTERNAL RATIOS

Third
gear
Second
gear
1 to 2.67
1 to 3.16
1 to 1.76
1 to 2.09
1 to 1.28
1 to 1.28
First
Standard
Competition
Fourth
gear
(top)
gear
1 to 1
1 to 1
FORK SPRING DATA

Year
Part No.
017127
010308
012972
015002
016526
016782
021784
021789
1945-46
1948
1949
1950
1951-54
1951-54
1955
1955-60
Free length
9.997 in.
10~ in.
11 in.
12.09 in.
12.t in.
12% in.
12% in.
12% in.
Solo 6G ~ Use 016782 for

Solo 6G
sidecar
Solo 6G
Solo 6G
Solo 6G
Sidecar 0.212 in. dia. wire
Solo 5l1G
Sidecar 0.212 in. dia. wire
REAR SUSPENSION SPRING DATA

011945
016297
016061
023373
023372
1950
1951-56
1951-56
1957-60
1957-60
8% in.
-It-
5% in.
5% in.
.. in. dia. wire (Solo)

~
in. dia. wire

in. dia. wire (Sidecar)
Solo
Sidecar
APPENDIX OF USEFUL TECHNICAL DATA

The following dala are common to all machines except ex- W.D.
350 c.c. ModeI41-G3L.
Stroke 93 mm.
Tappet clearance Nil, t.d.c., firing

stroke
Magneto contact gap 0.012 in.
Flywheel balance factor 6S %
End ftoat (max.) 0.025 in.

Valve lift
in.
n-
Valve seat angle 45 0
Camshaft bush tin. 0.0005 in.

Camshaft axle
t in.-0.00125/0.00175 in.
Crankpin diameter
Piston ring gap
1.20350/1.20375 in.
0.003 in. per each inch in diameter.

37
TECHNICAL DA TA
Crankpin rollers 0.25 x 0.25 in. (30

off)
d sIeeve In
..
Connecting-fo
SItu dlame"ter
1.7037511.70400 in.
.
Drivins-side shaft 0.9997/1.0002 1R.
Gudgeon pin size
i in.-O.OOJO/O.OOI3 in.
Rocker axle bush

i in.+0.00075 in.-0.0005 in.
Rocker axle sleeve, 010
8ore,mm
Stroke, mm
Capacity, cc
Compression ratio
Valve timing
Inlet opens B.T.D.C.
Inlet closes A.B.D.C.
Exhaust opens
B.B.D.C.
Exhaust closes
A.T.D.C.
Ignition before T.D.C.,
full advance
Tappet clearance, engine
cold
Carburetter, bore size
Main jet
Slide
Needle position
Needle jet
Needle
Cylinder size
Tolerance + 0.0005
-0.0005
K.L.G. sparking-plug
Magneto contact gap
Gearbox lubricant
Petrol-tank capacity,
pints
Petrol-tank reserve, pints
Oil-tank capacity, pints
Top of skirt, piston
diameter
Top ofskirt, mean
diameter
Bottom of skirt, piston
size
Bottom of skirt, mean
diameter
Gudgeon-pin size
0.6230/0.6235 in.
Small end bush

i in.+0.00050 in.-0.00025 in.
Valve timing
0.016 in. tappet clearance
Connecting-rod length,
centres
t945
1945
1946
1946
1947
1947
350-cc
5OO-cc
350-cc
5OO-cc
350-cc
500-cc
69
93
82.5
69
82.5
69
93
93
93
93
347
498
6.0
6.35
498
347
6.0
6.35
347
6.35
82.5
93
498
6.0
. All models use 0.016 tappet clearance

32
32
32
32
32
32
63
63
63
63
63
63
65
65
65
65
65
65
30
30
30
30
30
03
All %
All models nil clearance
Set with piston on T.D.C. firing stroke
1,..1'"
1
1*
180
150
180
180
150
150
6/4
29/4
29.4
6/4 29/4
6/4
2
2
2
2
2
2
4.061 29.076 4.061 29.076 4.061 28.076
29
6
29
6
29
6
2.7187 3.250 2.7187 3.250 2.7167 3.250
F80
F80
F80
F80
0.012
1 % pints light grease
24
F80
F80
4
4
All 350 cc 2.7132
All 500 cc 3.2435
All 350 cc 2.7143
All 500 cc 3.2446
-0.0010
-0.0013
7% 11945-46)
6% (1947)
y"
(All dimensions are in inches unless otherwise indicated.)

1949 1950-60 1950-60

1946
1946
1949
350-cc 500-cc 350-cc 500-cc 350-cc 5OO-cc
350-cc and 500-cc models
Rocker-axle bush
Camshaft bush
Rocker-axle sleeve
Camshaft axle
Small-end bush
Flywheel end-float
Flywheel diameter
Balance factor
Total rotating weight
Reciprocating weight
Balance weight
Exhaust pipe
Wheel base
Head angle
Trail
Valve spring, free length
inner
outer
Valve lift
Valve-seat angle lall engines)
Push-rod, overall length
Valve guide (inlet)
Protrusion (exhaust)
Valve stem (inlet)
Diameter (exhaust)
Crankpin diameter
Crank-pin rollers
Connecting-rod sleeve
diameter
Timing-side bush
Driving-side shaft
l'o -0_0020
-0_0025
% +0_00075
-0.00050
* +0.0005
-0.0005
High limit 0.6235
Low limit 0.6230
-0.00125
-0.00175
l'o + 0.00050
-0.00025
0.025 maximum
With shock absorber spring removed
All 350 7 l'o x 1.098
AII5007~ xl.l56
All 65%
All 350 843.3 gm.
All 500 843.3 gm.
All 350497.4gm.
All 500 673.2 gm.
All 350 lib. 4 oz. 9~ gm. (one flywheel)
All 500 1 lb. 6 oz. 8 * gm. (one flywheel)
Best length (open) 4B
63
63
2%
H
H
..I-
45
All 3509. All 5009-.1*
0.3730 high limit and 0.3720 low limit

All 0.250 x 0.0250 (30 off)
l'o + 0.00075
+0.0

MATCHLESS SINGLES 1939 - 1955
TECHNICAL DATA 1945-47 -continued
Timing-side shaft diameter
TECHIV'l.AL u .... ,J14
Bore, rnm
Stroke, mm
Capacity, cc
Compression ratio
Valve timing
Inlet opens B.T.D.C.
Inlet closes A.B. D.C.
Exhaust opens
B.B.D.C.
Exhaust closes
A.T.D.C.
Ignition before T.D.C.,
full advance
Tappet clearance, engine
cold
Carburetter, bore size
Main jet
Slide
. Njedle position
Needle jet
Needle
Cylinder size
Tolerance + 0.0005
-0.0005
K.L.G. sparking-plug
Magneto contact gap
Alternator gap
Gearbox lubricant
Petrol-tank capacity,
pints
Petrol-tank reserve, pints
Oil-tank capacity, pints
Top of skirt, piston
diameter
Top of skirt, mean
diameter
Bottom of skirt, piston
size
Bottom of skirt, mean
diameter
Gudgeon-pin size
Connecting-rod length,
centres
69
93
347
6.35
82.5
69
82.5
69
93
93
93
93
498
6.0
347
6.35
498
6.0
347
6.35
82.5
93
498
6.0
All models use 0.016 tappet clearance

32
32
32
32
32
32
63
63
63
63
63
63
65
65
65
65
65
65
30
30
30
30
All */I~,..
30
30
"'M.
All models nil clearance

Set with piston on T.D.C. firing stroke
1-1<
1
a
1
1
150
lSO
ISO
150
150
29/4
6/4
29/4
29/4
6/4
6/4
2
3
2
3
2
2
4.061 29.076 4.061 29.076 4.061 29.076
29
6
29
6
6
29
2.7187 3.250 2.7187 3.250 2.7187 3.250
1~""
F80
F80
FSO
F80
FSO
0.012/0,~ ....
0.019-0.016
1 pint engine oill'l,.l...
24/13'sL.
FESO"
C""',.-o_
N4
--
4/1,H.
4
AII350-cc 2.7176
AII500-cc 3.2490
AII350-cc 2.71SO
AII500-cc 3.2494
l(,
-0.0010
-0.0013
6% (1948-51)
(All dimensions are in inches unless othetwise indicated.)
" Alloy head.

38
TECHNICAL DATA 1948-60-continued

1948
350-cc
Timing-side shaft dia-
1948
1948-51
1948
500-cc
350-cc
500-cc
1950-53
500-cc
All 1948-49 10
0.0020
-0.0025
All 1950-51 10 -0.00150
-0.00175
% +0.00075
-0.00050
% +0.0005
-0.0005
High limit 0.6235
meter
Rocker-axle bush
Camshaft bush
Rocker-axle sleeve
Timing-skle shaft diameter
Rocker-axle bush
camshaft bush
Smal~end
Aywheel diameter
With shock absorber spring remove
All engines (after 80001
Flywheet diameter
Balance factor
All 350 843.3 gm.

AIISOO 843.3 gm,
All 350 497.4 gm.
AIISOO 673.2 gm.
All 350 lib. 4 oz. 914 gm. (one flywheen
AIiSOO lib. 6 oz. 814 gm. (one flywheell
Balance weight
Head angle
Trail
Valve spring. free length
inner
outer
53
63%'
2
2*
-I.-
Valve-seat angle (all engines)
45'
Valve guide (inlet'

protrusion lexhaust)
Valve stem dis. (inlet'

"
..
(exhaustl
Crank-pin diameter
Crank-pin rollers
diameter
Timing-side bush
53
6314'
2%
Valve lift
2%
2
54
63%0
54
63%
2%
2
2%
2
-I.-
45'
9-1.II
-I.-
45'
45'
Exhaust pipe
54
6314'
2%
2
9-1.II
..

0.3715 high limk and 0.3705 low limit
0.250 x 0.250 (30 offl
All 1948-49 10 + 0.00075
+0.0000
1.0002 high limit 0.9998 low limit
-I.-
45'
. ..
9-1.II
% +0.00075
-0.00050
II +0.0005
-0.0005
High limit 0.6235

Low limit 0.6230
II -0.00125
9-/0
II
-0.00175
10 +0.00050
-0.00025
0.025 maximum
With shock absorber spring removed
All engines (after 80001
714 x 1.156
All 65%
All 350 843.3 gm.

AIISOO 843.3 gm.
All 350 497.4 gm.
AIISOO 673.2 gm.
All 350 lib. 4 oz. 914 gm, (one flywheall
AIISOO 1 lb. 6 oz. 814 gm. (one ftywheall
Be.. length (openl48
Whael base
Head angle
Trail
narrow
-I.-
All 195051 " + 0.0005
39
Balance weight
2*
+0.0
Driving-side shaft
Best~(openl49
Exhaust pipe
Wheel base
Balance factor
714 x 1.156
65%
bush
Flywheel end float
-0.00025
0.025 maximum
Flywheel end float
1.2275-1.2300
Camshaft axle
II -0.00125
-0.00175
10 +0.00050
small-end bush
350-cc and 500-cc models
Rocker-axle sfeeve
lowlimitO.~
Camshaft axle
TECHNICAL DATA

wide
Valve HIt
Valve-seat anglo (all engines)
ValVe guide (inlet)
protrusion (exhaust)
Valve stem dia. (inletl
(exhaust)
"
"
Crankpin diameter
Cral)kpin rollers
diameter
Timing-side bush
Driving-side shaft
54
350-cc
6314'
500-cc
6314'
2%
2%
2%
3%
2
2
2
j,
j,
45'
45'
H
II
II
0.3730 high limk and 0.3720 low limit
0.250 x 0.0250 (30 0111
1.125-1.1255
(All dimensions 8re in inches unless otherwise indicated.)

ENGINE
SPROCKET
15 teeth
16 teeth
17 teeth
'18 teeth
19 teeth
20 teeth
t21 teeth
RATIOS-347
C.C.
2nd
3rd
18.69
17.5
16.44
12.32
11.54
10.48
10.26
9.6
9.24
8.8
8.96
8.39
7.88
7.47
7.0
6.72
6.4
IS.s7
14.6
14.01
13.35
GEAR
ENGINE
15 teeth
'16 teeth
17 teeth
tl8 teeth
19 teeth
20 teeth
21 teeth
498 C.C.
lst
'Standard 3SO C.c.
SPROCKET
AND
GEAR
ENGINE DESIGN CHANGES
MODELS
INTERNAL
RATIOS
Top
7.0
lst
2nd
3rd
Top
6.s6
6.16
5.83
5.49
5.25
5.0
2.67
1.76
1.28
1-1
t Standard 500 c.c.
1947 Models
(I) Improved type oil-pump plunger (two-start type) with neW
timing-side axle (identified by 2S stamped on plunger).
(2) Oil-feed passage in timing-side half crankcase increased to -Ir- in.
diameter to prevent cavitation, with corresponding increase in
diameter of the oil pipe, (%-in. diameter).

(3) A two piece oil pump guide pin -I.-in. in diameter to prevent wear on
the pin due to the increased plunger speed.
(4) Shorter connecting-rod.
(5) The use of a long plain bush for the timing-side bearing; the small
roller bearing is now obsolete. Engines fitted with the old-type
bearing can use a modified bush with two external diameters. The
steel sleeve is retained to locate the new bush on the large external
diameter.
RAnos--COMPETITION MODELS
1st
2nd
3rd
Top
22.12
20.72
19.46
18.44
17.34
16.59
15.8
14.63
13.71
12.87
12.20
11.47
10.97
10.45
8.96
8.39
7.88
7.47
7.0
6.72
6.4
7.0
6.56
6.16
5.83
5.49
5.25
5.0
TECHNICAL DA TA
INTERNAL
RATIOS
1st 3.16
2nd 2.09
3rd 1.28
Top I-I
1948 Models
(I) Annular groove in pump plunger increased from -I. to %-in.
diameter with suitable guide pin.
(2) Wire-wound pistons fitted to 5OO-cc models.
(3) 5OO-cc type high crankcase used for 350-cc models after engine
number 8000.
(4) 5OO-cc flywheels used for the 350-cc model.
(5) Larger brakes (7- in. diameter).
1949 Models
(1) New-type cylinder-head, with hair-pin valve springs with rocker box
to suit.
, Standard 350 C.c.
(2)
(3)
(41
(5)
t Standard 500 C.c.
CARBURETTERS
The various types of Amal carburetters fitted are siven below:
..
347 c c Mod.l
YEAR
TYPE
1946-50
1951-53
1954
1955
76DIJ
76/AEjIAK
76AV lED
376/5
BORE
SIZE
1 in.
1 in.
1.063 in.
1.063 in.
SUDE
6x4
6x4
6x4
376/060.3
NEEDLE
POSITION
MAIN
2
2
2
3
ISO
ISO
JET
ISO
210
498 C.c. Models

YEAR
1946-53
1954
1955
TYPE
89B/1AK
89NIED
389/1
BORE
SIZE
1.097 in.
1.161 in.
1.161 in.
MAIN
JET
180
180
260
SUD.
NEEDLE
POSITION
29/4
29/4
389/060.3
3
2
3
Valve lifter transferred from crankcase to rocker box.

Wire-wound pistons for all models.
Longer valves, hardened valve end caps discarded.
New rockers for longer valves, also new valve guides.
1950 Models
(1) Alloy cylinder-heads and barrels used on Competition models only.
Steel crankpin washer in place of bronze type.
1951 Models
(1) Alloy cylinder-heads used on both touring-type engines. Crankpin
washers discarded, flywheels altered.
1952 Models
(I) Open-tray valve-spring seat, prongs for valve springs increased in
length.
(2) Cylinder barrel lengthened %- in. on 5OO-cc touring engine,
compression plate discarded.
(3) Recess for driving-side bearings in crankcase with two diameters, for
close and easy interference fit to avoid "end loading" of these
bearings.
(4) Top compression ring chrome-plated.
ENGINE DESIGN CHANGES-continued

1953 Models
No change.
1954 Models
(1) Oil feed in rocker box modified to increase oil supply to rocker end of
inlet valve and stop valve-spring wear.
(2)
(3)
(4)
(5)
New rockers for valve ends with groove in side for oil duct.
High-lift cams.
Larger-diameter timing-side shaft, with flywheel to suit.
Two-diameter timing-side bush, steel sleeve discarded.
(6) Automatic ignition control on 500-cc model.
1955
(1)
(2)
13)
Models
New crankcase to use one small and one large driving-side bearing.
New driving-side flywheel (keyways at 180%).
Circlip fitted to exhaust-valve guide.
1956 Models
111 Cylinder-wall oil feed discontinued.
(2) Compression ratio increased to 7.5 lor 350-cc models, 7.3 for 500-cc
models.
(31 Oil-tank felt lilter deleted and magnetic filter fitted in crankcase.
1957 Models
(11 Engine-shaft shock absorber discarded, shock absorber incorporated
in the clutch assembly.
(21 A.M.C. gearbox on all models.
(31 Improved detachable rear-wheel design.
(41 Girling rear suspension units introduced.
TECHNICAL DATA
PERMISSIBLE FRAME MODIFICATIONS-continued

Rear Suspension
"Jam-pot" Units, first used in 1951, can be adapted for 1950 models ij the
top anchorage on the frame loop is cut away to clear the unit top pivot.
Front Chaincase
The outer portion of the chaincase with a detachable clutch cover for
clutch adjustment, w~hout disturbing the chaincase, first used in 1954,
can be fitted to earlier models.
Full-width Hubs
The full-width front hub can be fitted to any model which has Teledraulic
forks.
Rear-wheel hubs of the same type can also be fitted to any spring-frame
model.
Spring Frame
Rigid-frame models made from 1949 can be converted into spring frame
models.
1958-60 Models
111 Lucas RM 15 Alternator A.C. lighting/ign~ion used on 350 cc and
500-cc models.
(21 Aluminium front chaincase replaces steel type.
PERMISSIBLE FRAME MODIFICATIONS
TECHNICAL DATA FOR EX-W.O. 350 cc MODEL 41-G3L
Front Forks
Longer Fork Springs (free length 12~ in.) can be used in place of earlier
types, which were 9.997 in. and 11 in. free length. The longer springs
improve the fork motion, but will expose the holes in the slider
extension first used in 1954. Buffer springs for fork inner tubes can be
used on models before 1947.
1946 Top Fork Cover Tubes with incorporated lamp brackets will
interchange with the earlier type to discard the strip-steel lamp
brackets.
Polished Fork Sliders, in place of the black-enamelled type, can be fitted
without other alteration.
A 1955-type Front Mudguard, which dispenses with the two strip-steel

stays, will I~ any machine fitted with Teledraulic forks made before
1956. Front forks with large-diameter tubes (1955-57) can be fitted to
earlier models.
41
Cubic capacity 347 c.c.

Stroke 93 mm. (3.6614 in.)
Cylinder bore 2.7187 in. 0.OOO5 in.
Compression ratio S.88: 1 with plate
6.30 : I without
plate
AXLES
Camshaft axle diameter
t in.-0.0012510.00175 in.
DrivinB ftywheel axle diameter
I in. 0.OOO2 in.
Gearbox mainsbaft lensth 101 in.
Timing side ftywheel axle diameter
i in.-0.003010.0035 in.
Nut retaining small timing pinion to

ftywheel axle 0.7 in. x 26 tpi, left
hand thread.
Flywheel axle run
to 0.001 in. from dead true.
BALL JOURNAL BEARINGS

Driving side ftywheel axle ball beariogs Bore I x 2* io. 010 by i in.
Gearbox main gear ball bearing
Bore 1.281 in. x 62 mm. 010 by
16mm.
Gearbox mainsbaft (right-hand end)
ball bearing Bore 12x4O mm. 010
x 17 mm.
Steering head 0.187 in. balls (56 oft')
BIG-END BEARING
Crankpin diameter on roller race
1.20325/1.20350 in.
Crankpin diameter in flywheel
0.8775/0.8780 in.
Crankpin rollers diameter ... x
(30 off)
in.
Big-end liner external diameter
PISTON
Top land 2.6877 in. 0.0005 in.
2nd land 2.6962 in. 0.0005 in.
3rd land 2.6962 in. 0.0005 in.
Top of skirt 2.7132 in. 0.0005 in.
Bottom of skirt 2.7143 in. O.OOO5 in.
(Measurements at right
gudgeon pin)
angles
to
2.0000/2.0005 in.
Big-end liner internal diameter
1.70375/1.70400 in. (fitted and ground)

BUSHES
(FITTED AND REAMED)
Camshaft bushes tin. O.OOOS in.

Gudgeon pin bush i in.+O.OOOS in.
-0.00025 in.
Rocker bushes
Timing axle bush
in. +0.001 in.
-0.000 in.
t in.+O.OO125 in.
-0.00150 in.
CAPACITIES (OIL OR GREASE)

Front forks 6t fluid oz. S.A.E.20'''','cc.
Gearbox I i pis. light grease
Oil tank 3 pis.
Petrol tank 3 gallons
CARBURETTER
CarbureUer Amal, type 275 F/U.
(W.O. tYjle)
Main jet Size 120
Throttle valve size 5 x 5
Jet taper needle Early models lcd,
later models 4th notch.
CHAINS
Front t x 0.305 in. (66 links)
Rear t x 0.3g0 in. (91 links)
Malneto t x 0.225 in. (58 links)
Dynamo t x 0.225 in. (47 links)
(Whip"'front. i in.; rear, i in. to tin.;
magneto, i in.; dynamo. i in.)
CLUTCH
Thrust rod 9iin.
Gear ratios 5.8,7.5, 12.2 and 18.5 : 1
Gudgeon pin diameter
t in.-0.0010/0.0015 in.
IGNITION
Contact breaker points 0.012 io.
Setting, b.t.d.c., fully advanced

0.43g in. (max. tin.)
Plug gap 0.020/0.022 in.
PISTON RINGS
Compression 2.719xO.062S in.
Scraper 2.719xO.125 in.
Gap Normal, 0.006/0.008 in. (max.
0.030 in.)
Ring clearance 0.003 in.
Rocker sleeve diameter
0.6230/0.6235 in.
SPROCKETS
Clutch 40 teeth (t x 0.305 in. cbain)
Engine 18 teeth (t x 0.305 in. chain)
Gearbox
16 teeth (i x 0.380 in. chain)
Rear wheel 42 teeth (t x 0.380 in.

chain)
TAPPET GUIDES
Projection from crankcase face
0.281 in.
VALVE TIMING
Exhaust opens 65 b.b.d.c.; closes 30
a.t.d.c.
Inlet (enF.es before No.0 54512)

opens 20 b.t.d.c.; closes 67 a.b.d.c.
Inlet (engines after No. 54512) opens
32 b.t.d.c.; closes 63 a.b.d.c.
(All timings with 0.016 in. tapped
clearance.)
VALVES
Clearance (cold engine) nil
Head diameter inlet 1.864 in. O.OOS
in.; exhaust I.S in. O.OOS io.
Seat ansle 45
Stem diameter. inlet and exhaust
0.375 in.-0.0034/0.0045 in.
VALVE GUIDES
External diameter
t in.+0.00175/0.00225 in.
Internal diameter tin. O.OOOS in.
Projection from cylinder head Inlet
tin.; exhaust i in.
VALVE SPRINGS
Outer valve spring free length
2.0625 in.
Inner valve spring free length
1.812 in.
(Replace springs when 0.1875 to 0.25
in. below these lenlths)
EX-WD G3L DATA-continued

Matchless Motorcycles

Uploaded by

Copyright:

Available Formats

Matchless Motorcycles

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Matchless Motorcycles

Uploaded by

Copyright:

Available Formats

What is the book about?

What is the book about?

What models of Matchless motorcycles does the book cover?

What models of Matchless motorcycles does the book cover?

This scan is explicit for non-commercial u

TEMPLE PRESS LIMITED

MATCHLESS SINGLES 1939-1955

Also Visit my website for 7 FREE Download Manuals starting

"The ABC's of Carburetion"

file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]

This scan is explicit for non-commercial

(Left) Another maker's definitive

Joe Fnae" Moton RecBlde

Maker's definitive photographs

,-:Again a factory photograph. The

troduced from September 1953

fuJl-mdth (ront hub of 7-inch

welded (ront frame and

seat. Rear legs are AMC's own

Jampots. The alfoy motor has

MATCHLESS SINGLES 1939-1955

This scan is explicit for non-commercial u

FOREWORD TO THE ORIGINAL BOOK

Suggested equipment for this purpose is listed below:

This scan is explicit for non-commercial u

1. DECARBONIZING THE ENGINE

This scan is explicit for non-commercial us

DECARBONIZING THE ENGINE

Top-haH components of the Matchless WD-G3L, e;,ea 1941

torque spanner is available, set it to 36 Ib.ft.

is restricted; it is therefore preferable to fit the carburetter to the cylinder head

This scan is explicit for non-commercial u

NCAF<80NIZING THE ENGINE / SERVICING ENGINES

Bottom-half crankshafts with drive-side crankcase.

Heavy Oil Consumption

MATCHLESS SINGLES 1939-1955

This scan is explicit for non-commercial u

Excessive Smoke on Starting

Oil Pump Plunger

. 7. Dowel peg. locating timing-gear cover

6. Screwed body for guide pin

Z Guide pin in position engaged in profUad

Rocker Box Oil Suppl'y

This scan is explicit for non-commercial us

Correct assembly of the oil

plunger must mesh with

The oilways in the valve guides

Crankcase Release Valve

crankcase to escape into the atmosphere.

disc in position whilst the valve is refitted.

MATCHLESS SINGLES 1939-1955

This scan is explicit for non-commercial us

Exhaust Valve Seizure or Sluggishness

Hairpin Valve Spring and Collar Wear

Refitting Valve Guides

Loose Valve Guide

Removing the exhaust-valve guide on alloy cylinder heads without pre-heating

This scan is explicit for non-commercial u

SERVICING ENGINES I OVERHAUUNG THE ENGINE

Valve Guide Protrusion