Method and Modelling For Allocating Wavelength in WDM Passive Optical Networks

International Journal of Engineering and Technical Research (IJETR)
ISSN: 2321-0869, Volume-2, Issue-10, October 2014
Method and Modelling for Allocating Wavelength in

WDM Passive Optical Networks
Vikas Chhabra, Monika Dhiman
Abstract To circumvent issue of Rayleigh noise reduction in

wavelength-division-multiplexed passive optical network
(WDM-PON), we provide an insight into the source of Rayleigh
noise, and confirm that suppression of carrier Rayleigh
backscattering (RB) should be the primary target in the design
of Rayleigh noise-resilient upstream receiver module. It propose
and demonstrate an effectively scheme suppress the carrier RB
in carrier-distributed WDM-PONs.
This paper studies
alternative network architecture with dynamic wavelength
allocation to provide a scalable optical architecture with a
guaranteed QoS in the presence of dynamic and bursty traffic
loads. In this research work, the issue of connection provisions
and performance analysis in WDM network ensuring the
quality of service requirement of the connection requests from
the client in the network in optical networks. While designing
WDM system is explored, it considers the physical layer
impairments incurred by non-ideal optical transmission media
that accumulates along the optical path. For very high
transmission speed, dispersion developed a considerable
degradation factor and in this work concentrated on the effects
of dispersion on fiber design parameters such as bandwidth,
delay and bit rate. The dependence of carrier RB suppression on
DIs extinction ratio (ER) and optical carriers line width is also
theoretically analysed. In this article, we present a
delay-constrained admission control mechanism and adapt this
scheme to our previously proposed bandwidth allocation
technique. The main relations between different parameters of
optical network unit (ONU) are also studied.
Index Terms Passive Optical Networks, WDM-PON,
Wavelength Allocation, Rayleigh Scattering Parameters.
I. INTRODUCTION
Foreseeing the rapidly growing demand for multimedia
services and the trend of service convergence, the
wavelength-division-multiplexed (WDM) passive optical
network (WDM-PON) is a promising technology to provide
next-generation broadband access that requires large
dedicated symmetric bandwidth and upgrading flexibility. An
optical network is a type of data communication network built
with optical fiber technology. It utilizes optical fiber cables as
primary communication medium for converting data as light
pulses between sender and receiver nodes. Wavelength
division multiplexing (WDM) technology is a strong
candidate for next generation high performance networks
because it provides large bandwidth, low bit error rate, low
control requirements and low cost. WDM knowledge has
provided tremendous bandwidth for optical fibers by
Manuscript received October 13, 2014.
Vikas Chhabra, ECE Department, Galaxy Global Inst. of Engg,
Kurukshetra University, Ambala, Haryana.
Monika Dhiman, Asst. Professor, Ambala College of Engg. & Applied
Research/ ECE Department, Kurukshetra University, Ambala, Haryana .
99
allowing simultaneous transmission of traffic on many

non-overlapping channels (wavelengths) in an optical fiber
[1].
In a wavelength-routed WDM system, end users
communicate with one another via all-optical WDM
channels, which are referred to as light paths [2]. A passive
optical network (PON) is a point-to-multipoint, fiber to
premises system architecture in which unpowered optical
splitters are used to enable a single optical fiber to serve
multiple premises, typically 16-128. A PON consists of
optical line terminal (OLT) at the service provider's central
office and a number of optical network units (ONUs) near
end users. Passive optical network (PON) has advantages in
high bandwidth capacity, also low operation and maintenance
rate, and has been measured as a promising access network
solution and widely deployed [3]. Various PONs, e.g.,
Ethernet PON (EPON) and Gigabit-capable PON (GPON),
use time division multiplexing (TDM) technique to enable
multiple users to share a common wavelength bandwidth
resource in PON, and they are called as TDM PONs. WDM
technology enables network operators to continuously
increase the capacity of their networks. Undoubtedly, WDM
will continue the key technology to satisfy the ever increasing
demand for more bandwidth within the next years [3].
In multi-hop network design, the selection of a proper
logical topology is followed by the wavelength assignment
process. The simplest scheme for wavelength assignment
assigns one wavelength channel to each of the logical links.
An alternative scheme that requires a smaller number of
wavelengths and transmitters is the assignment of one
wavelength channel per end-node. If number of wavelength
channels in the network is smaller than the number of
end-nodes, these schemes will fail. The carrier RB light
towards OLT, with a fine spectrum, can be effectively
suppressed by an optical notch filter. While carrier
regeneration decreases number of wavelengths, the signal
quality of carrier must be considered because it becomes
slightly worse after regeneration. If signal quality becomes
unacceptable after several regenerations, its wavelength
should not be reprocessed anymore in order to eliminate
communication fault. i.e, the allowable number of carrier
regenerations per wavelength should not be exceeded [6].
The paper is organized as follows. In section II, we discuss
related work with the wavelength allocation scheme. In
Section III, It describes the types of PON. Section IV
describes the proposed system architecture and analyse the
different parameters of Rayleigh scattering in impairing the
upstream signal. Section V reports the effectiveness of the
proposed scheme and also describes the results of scheme.
www.erpublication.org
Method and Modelling for Allocating Wavelength in WDM Passive Optical Networks
The various relations between different parameters are
examined. Finally, conclusion is given in Section VI.
II. RELATED WORK
In literature, several proposed Rayleigh noise reduction in
wavelength-division-multiplexed passive optical network
(WDM-PON). Then they propose and demonstrate a novel
scheme to effectively suppress the carrier RB in
carrier-distributed WDM-PONs. By simply replacing
upstream modulation format of conventional on-off keying
with differential phase-shift keying (DPSK), the system
tolerance to carrier RB is substantially enhanced by 19 dB, as
carrier RB can be considerably rejected by the notch
filter-like destructive port of the delay-interferometer at the
optical line terminal, which is used instantaneously to
demodulate the upstream DPSK signal. As no thoughtful
spectral up-shifting is required in this scheme, neither other
modulator nor complicated modulation/demodulation circuit
is needed at ONU/OLT. In terms of optical notch filter used to
reduce RB light, the standard DI used in the future scheme is
also more favourable than the non-standard filters [2].
Authors propose and demonstrate a novel colourless optical
transmitter based on all-optical wavelength conversion using
a reflective semiconductor optical amplifier for upstream
transmission in wavelength -division- multiplexed passive
optical systems. The proposed colourless optical transmitter
for the optical network unit is composed of an
electro-absorption modulated laser, a photosensitive coupler,
and an RSOA. Through cross-gain modulation in RSOA, the
upstream data from the EML pump light are imposed onto a
continuous-wave probe light provided from the central office.
An optical delay interferometer at CO tailors the chirp of the
upstream signal to improve the bandwidth of the system and
dispersion tolerance. The proposed optical transmitter is
based on the fast gain recovery of the RSOA governed by
carrier-carrier scattering and carrier-phonon relations.
End-to-end real-time optical orthogonal frequency-division
multiple-access (OOFDMA) passive optical networks
(PONs) with adaptive dynamic bandwidth allocation (DBA)
and colourless optical network units (ONUs) are
experimentally established, for the first time.
Next generation Passive Optical Network (PON) technology
has been evolving to consolidate the metro and access
networks in order to offer enhanced capacity, high split ratio
and compact deployment cost per subscriber. However,
transmission of signals to long distances up to 100km leads to
increased propagation delay whereas high split ratio may lead
to long cycle times resulting in large queue occupancies and
long packet delays. In this article, they current a
delay-constrained admission control mechanism and adapt
this scheme to our previously proposed bandwidth allocation
technique. This paper investigates problem of dynamic wave
length allocation and fairness control in WDM optical
networks. An f network topology, with a two-hop path
network, is studied for mainly three classes of traffic. Each
class corresponds to a source & destination pair. For each
class call inter-arrival & holding times remain studied. The
objective is to find a wavelength allocation policy to
maximize the weighted sum of users of all the three programs.
100
In a conventional WR network, an entire wavelength is

assigned to a given connection. This can lead to lower channel
utilization when individual sessions do not need the entire
channel bandwidth [7].
III. TYPES OF PON
A PON system uses the passive splitter that takes one input
and splits it to "broadcast" signals to many users.
A. Broadband Passive Optical Network
For many network operators, an optical access network is the
ultimate target for the delivery of fixed broadband services.
The BPON is accepted as a cost-effective fibre to the home
solution well-suited to the future needs of broadband services.
A major feature of the BPON is that 32 customers can be
concentrated on a single fibre to the central office using a
simple passive optical splitter. Since optical splitter requires
no electrical power, it removes a major cost and maintenance
element in todays digital loop carrier systems. The BPON
supports a bit rate of 622 or 155 Mbit/s in the downstream and
upstream direction, which is shared by the users through time
division multiplexing. Broadband passive optical network
standards are based on the G.983 series of ITU-T
Recommendations that specify ATM as the transport and
signalling protocol. By improving the optical budget on the
BPON fibre, up to 128 or 256 homes could be passed by a
single high split. Up to 64 of these homes could be connected,
which is the maximum number of ONUs (Optical Network
Unit) that can be identified by a G.983.1 compliant system. In
preparation for higher service penetrations, optical splitter in
the outside network would be limited to 8, 16 or 32-way split.
Since exchange carriers have an extensive embedded ATM
switching infrastructure, these carriers are using BPON
technology to deploy the fiber-to-the-premises networks. By
improving the optical budget on the BPON fibre, up to 128 or
256 homes could be passed by a single high split. . In
preparation for higher service penetrations, optical splitter in
the outside network would be limited to 8, 16 or 32-way split.
B. Ethernet Passive Optical Network
Data traffic is increasing at an unprecedented rate.
Sustainable data growth rate of over 100% per year has been
observed since 1991. There were periods when a combination
of economic and technological factors resulted in even larger
growth rates, e.g., 1000% increase per year in 1995 and 1996.
Ethernet PON (EPON) is a PON-based network that carries
data traffic encapsulated in Ethernet frames (defined in IEEE
802.3 standard). It uses a standard 8b/10b line coding (8 user
bits encoded as 10 line bits) and operates at standard Ethernet
speed. Since this method encapsulates and transports data in
Ethernet frames, it is easy to carry IP packets over an Ethernet
link. This scheme thus simplifies the interoperability of metro
and wide area network assets with installed Ethernet LANs
compared to the use of BPON technology. Ethernet has
become a universally accepted standard, with over 300
million port deployments worldwide, offers staggering
economies of scale. High-speed Gigabit Ethernet deployment
is widely accelerating and 10 Gigabit Ethernet products are
becoming available.

Ethernet, which is easy to scale and manage, is winning new
grounds in MAN & WAN. Considering the fact that 95% of
LANs use Ethernet, which clears that ATM PON may not be
the best choice to interconnect two Ethernet networks. One
EFM option uses an EPON architecture that follows the
standard PON layout, which has one main feeder line going to
an optical splitter. Up to 32 distribution branches leave the
splitter and interface to ONTs. The IEEE 802.3 standard
defines two basic configurations for an Ethernet network. In
one configuration, it can be organized over a shared medium
using the Carrier Sense Multiple Access with Collision
Detection protocol. In another configuration, stations may be
connected through a switch using full-duplex point-to-point
links. The Properties of EPON are such that it cannot be
considered either a shared medium or a point-to-point
network; rather, it is a combination of both. In downstream
direction, Ethernet frames conveyed by OLT pass through a
1: N passive splitter and reach each ONU. N is typically
between 4 and 64. This behaviour is similar to a shared
network. Because Ethernet is broadcast by nature, in the
downstream direction (from network to user), it fits perfectly
with Ethernet PON architecture: packets are broadcast by the
OLT and extracted by their destination ONU based on the
media-access control address. In the upstream direction, due
to the directional properties of a passive optical combiner,
data frames from ONU will only reach the OLT, and no other
ONUs.
C. Gigabit Passive Optical Network
The growing demand for higher speeds in the access
network spawned the idea of developing a PON with
capabilities beyond those of the BPON and EPON
architectures. A major aim of this idea was to develop a
versatile PON with a frame format that could transmit
variable-length packets efficiently at gigabit per second rates.
The FSAN group started such an effort in April 2001. The
result was the ITU-T recommendation series G.984.1 through
G.984.4 for a gigabit PON.
The GPON standard is defined in the International
Telecommunication
Union
Telecommunication
Standardization Sector (ITU-T) G.984.x series of
Recommendations sponsored by the full service access
network (FSAN). Several upstream and downstream rates up
to 2.48832 Gb/s are specified in the standard. Here we
consider the 1.24416 Gb/s upstream rate to make it
comparable with EPON. The GPON protocol is based on the
standard 125 s (~19,440 bytes at 1.24416 Gb/s) periodicity
used in the telecommunications industry. This periodicity
provides certain efficiency advantages over EPON, as
messages (control, buffer report, and grant messages) can
efficiently be integrated into the header of each 125 s frame.
Within GPON each Ethernet frame or frame fragment is
encapsulated in a general encapsulation method (GEM) frame
including a 5-byte GEM header. The network layout for a
GPON follows that of a standard PON concept. It also retains
much of the same functionality characteristic of BPON and
EPON schemes, such as DBA and the use of operations,
administration, and maintenance (OAM) messages.
101
IV. PROPOSED SYSTEM ARCHITECTURE AND

RAYLEIGH PARAMETERS
A. System Architecture
1
M
2 U L1
X
ns
L2
D
E
M
U
O
N
1
R
X 2
R
n
D
E
M
U
X
OA
Fig 1: Proposed system architecture to suppress Rayleigh sound. OA: optical

amp, D: delay-interferometer, MUX: Multi-plexer, DEMUX:
De-multiplexer, ON: Optical network Unit.
Fig. 1 shows the proposed architecture of a WDM-PON. As

downstream plus upstream signals are transmitted over
different wavelength bands in the carrier-distributed
WDM-PON, RB from upstream signal will not affect with the
downstream signal, and vice versa. Passive optical systems
have high bandwidth Point-to-Multipoint optical fiber
network based on the Asynchronous Transfer Mode (ATM),
Ethernet or TDM. PONs relies on light waves for data
transfer. Only passive components are used such as optical
fiber, splices and circulators etc. PONs reduces the fiber
deployment in both the local exchange office and local loop.
The PON is an access network based on optical fiber [11]. It
is designed to provide virtually unlimited bandwidth to
subscriber. The multi-wavelength optical carriers for
upstream transmission are generated by continuous-wave
(CW) lasers as centralized light sources, and then multiplexed
through an AWG. After transmission in a feeder fiber with a
length of L1, optical carriers are wavelength routed toward
different ONUs, by another AWG at the remote node (RN).
The length of the distribution fiber (between RN and ONU) is
L2. At ONU, CW light is first amplified and then modulated
driven by differentially pre-coded upstream data, before
being sent back to OLT. Due to DIs periodic frequency
response, all upstream channels could be simultaneously
demodulated by a common DI at the OLT. Note that only
destructive port of the DI can be used for upstream
demodulation and carrier RB suppression simultaneously due
to its notch filter-like frequency response [4].
B. Components Used
1. Transponders
Transponder is the basic element for transmission and
reception of optical signal from the channel. A transponder is
generally characterized by the maximum bit rate it can handle
with and the maximum distance the optical pulse can travel
without degradation. Transponders convert an optical signal
from one wavelength to an optical pulse with another
wavelength. Another important function of transponder
device is the conversion of broadband signal to a signal
associated with specific wavelength by optical to electrical to
optical conversion.
For detection purposes, it uses photo-detector. This
photo-detector generates an electrical current proportional to
the incident optical power. Photo-detectors are made of
semiconductor materials. Photons incident on a
semiconductor are absorbed by electrons in the valence band.
As a result, these electrons acquire higher energy and are
excited into the conduction band, leaving behind a hole in
valence band. When an outer voltage is applied to the
semiconductor, these electron-hole pairs give rise to an
electrical current, termed the photocurrent.
2. Wavelength Cross Connect
Wavelength cross connect is a switching device whose
function is to switch or connect any wavelength from the input
port to any one of the out port in the fiber. The functioning is
completely in optical domain. An OXC with N input and N
output ports capable of handling W wavelengths per port can
be thought as W independent NN optical switches. The
polarization-independent Acoustic optical tunable filters
(AOTF) can be used as a two input, two-output dynamic
wavelength cross connect.
3. Couplers
A passive optical network employs a passive (not
requiring any power) device to split optical signal (power)
from one fiber into several fibers and reciprocally, to combine
the optical signals from multiple fibers into one. This device
is an optical coupler. In simplest form, an optical coupler
consists of two fibers fused together. Signal power received
on input port is split between both output ports. The splitting
ratio of splitter can be controlled by the length of the fused
region and therefore is a constant parameter. A directional
coupler is used to combine and split signals in an optical
network.
4. Circulators
A circulator is similar to isolator, except that it has
multiple ports, typically three or four. In 3-port circulator, an
input signal on port 1 is sent out on port 2, a signal on port 2 is
sent out on port 3, plus an input signal on port 3 is sent out on
port 1. Circulators are useful to construct optical add/drop
elements. Circulators operate on the same principles as
isolators.
5. Multiplexers
Optical Add-Drop multiplexer is a device which is
capable to add or drop one or more wavelengths from the
existing WDM system. There are three important domains for
an OADM- optical multiplexer, de multiplexer and a method
to reconfigure the path between multiplexer and de
multiplexer. Demultiplexers and multiplexers can be
cascaded to realize static wavelength cross connects. . The
device routes signals from an input port to an output port
based on the wavelength.
6. Optical Amplifiers
An optical amplifier is a device which amplifies the

optical signal directly without optical to electrical conversion
i.e., all functions occurs in optical domain. In optical fiber, the
light pulse itself is amplified. Optical amplifiers provide high
gain and low noise for the optical signal; it has importance in
the overall bandwidth provided by WDM system. Optical
amplifiers offer several advantages over regenerators. On one
hand, regenerators are specific to the bit rate and modulation
format used by the communication system. On the other hand,
optical amplifiers are insensitive to the bit rate or signal
formats. Thus a system using optical amplifiers can be more
easily upgraded. Thus a system using optical amplifiers can
be more easily upgraded, for example, to a higher bit rate,
without replacing the amplifiers. In contrast, in a system using
regenerators, such an upgrade would require all the
regenerators to be replaced. Furthermore, optical amplifiers
have fairly large gain bandwidths. Thus optical amplifiers
have become essential components in high-performance
optical communication systems.
7. Interferometers
An interferometer is a device that makes use of two
interfering paths of different lengths to resolve different
wavelengths. Mach interferometers are typically constructed
in integrated optics and consist of two 3 dB directional
couplers interconnected through two paths of differing
lengths. Mach Zehnder interferometers are useful as both
filters and demultiplexers. Even though there are better
technologies for making narrow band filters, for example,
dielectric multi-cavity thin-film filters, MZI are still useful in
realizing wide band filters. Narrow band interferometers
filters are fabricated by cascading a number of stages.
8. Switches
Optical switches are used in optical networks for a
variety of applications. The different applications require
different switching times and number of switch ports. One
application of optical switches is in the provisioning of light
paths. In this application, switches are used inside wavelength
cross-connects to reconfigure them to support new light paths.
Switches are also important components in high-speed optical
packet-switched networks. In these networks, the switches are
used to switch signals on a packet-by packet basis.
For this application, the switching time must be much
smaller than packet duration, and large switches will be
needed. Yet another use for switches is as external modulators
to turn on and off the data in front of a laser source. In this
case, switching time must be a small fraction of the bit
duration. The extinction ratio of an on-off switch is the ratio
of the output power in the on state to the output power in off
state. This ratio should be as large as possible. The insertion
loss of a switch is the fraction of power (usually expressed in
decibels) that is lost because of the presence of the switch and
must be as small as possible. The switch needs to have a
readout capability wherein its current state can be monitored.
This is important to verify that the right connections are made
through the switch.
C. Rayleigh Parameters
Rayleigh scattering named after the British physicist
Lord Rayleigh, is elastic scattering of light or other
102

electromagnetic radiation by particles much smaller than the
wavelength of light. After the Rayleigh scattering the state of
material remains unchanged, hence this rayleigh scattering is
also said to be a parametric process. These particles may be
individual atoms or molecule. It can occur when light travels
through transparent solids and liquids, but it is most
prominently seen in gases. Rayleigh scattering results from
electric polarizability of particles. The oscillating electric
field of a light wave acts on the charges within a particle,
causing them to move at same frequency.
Rayleigh crosstalk is induced by the beating between the
upstream signal and the in-band RB noise towards the OLT.
Two types of RB exist: carrier RB and signal RB. The carrier
RB arises from the CW carrier delivered to ONU, whereas the
signal RB is the back reflection of the upstream signal, which
is further amplified and modulated at ONU before
transmitting to the OLT, along with the upstream signal. By
calculating the power ratio between two types of RB, we can
find out their different contributions in the upstream Rayleigh
noise [5].
We first calculate the power of carrier RB. The mean
intensity of the carrier RB produced in the feeder fiber is
given by [12]:
(7)
The mean intensity of signal RB generated in the distribution
fiber is given by equation (8):
(8)
Algorithm: Proposed Rayleigh Scattering Parameters
S=0.0016
p=0.046
Step 1: For (carrier RB):
Read Length L1 and L2.
Calculate (R1=2/S (1-e-2pL1) and R2=2/S (1-e-2pL2).
Calculate 1=epL1 and 2=epL2
Then calculate Mean intensity of carrier RB in feeder fiber
Pcb_1=Pc/R1 and Mean intensity of carrier RB in
distribution fiber Pcb_2=Pc/(1.A)2.R2
Step 2: for (signal RB):
(1)
Where Pc is the power of optical carrier incident to the feeder
fiber, and R1 is RB-induced return loss of the feeder fiber that
is given by equation (2):
Read L1 and L2.

Calculate (R1=2/S (1-e-2pL and R2=2/S (1-e-2pL2)
Calculate 1=epL1 and 2=epL2
Then calculate Mean intensity of signal RB in feeder fiber
(2)
With S, p being the recapture factor, and fiber attenuation
factor in units of km respectively. Now, mean intensity of the
carrier RB generated in the distribution fiber is given by
equation (3):
Psb_1=P.G2ONU/R1.12(A.2)4 and (Mean intensity of

signal
Pc.G
RB
in
distribution
fiber
Psb_2
ONU/R2(1.A.2)
Step 3: Calculate power ratio between two types of RB:

Pcb/Psb=[(1.A)2.R2+R1].24A2/G2ONU[(2.A)2.R1+R2]
(3)
Where 1, A are the insertion loss of the feeder fiber and the
AWG at RN in linear scale, respectively, and is RB induced
return loss of the distribution fiber. Now, 1 and R2 are given
by equation (4) & (5):
(4)
(5)
Similarly, we can calculate the power of signal RB at port 2 of
the OLT optical circulator. The mean intensity of the signal
RB generated in the feeder fiber is given by equation (6):
(6)
With 2 and Gonu being the insertion loss of the distribution
fiber and the ONU gain, respectively. The ONU gain is
defined as the power ratio between the output and the input
signals at ONU. 2 is further given by equation (7):
103
end
D. Estimation of Blocking Probability

Blocking probability is simply the ratio of total number
of calls blocked to the total number of calls expressed in
percentage. Minimum blocking is continually the desired
condition for provisioning. A connection requests can be
jammed either due to the availability of QoS satisfied path or
due to the absence of free light path. Blocking Probability
represents in terms of percentage (%). It is represented in
terms of Erlangs. The erlang (symbol E) is a dimensionless
unit that is used in telephony as a measure of offered load or
carried load on service-providing elements such as telephone
or telephone switching equipment. It is clear that if the nodes
have a smaller transmission radius then the interference
constraints on each hop are fewer but the calls hop through
many links to reach the destination. This increases the internal
load in the system. In contrast, a larger transmission radius
reduces the number of hops of a call but increases the
interference constraints at each hop. The effect of this trade
off on blocking probability is non-trivial and leads to different
observations under different node topologies.
Algorithm: Estimation of Blocking Probability
m=input('Enter the number of m ');
no. of servers
n=input('Enter the number of n '); % wavelengths

rho=input('Enter the number of rho ');
if ((floor(m) ~= m) || (m < 1))
considering different length ratio between the feeder and

distribution fibers.
Then based on equation (9) we can calculate the
maximum system margin and the required optimal ONU gain
for different system reaches. Thus, an attractive feature of
proposed scheme is that all ONUs with similar length ratios
can be set to a fixed gain even for a large change in system
reach.
F. Estimation Of Bit Error Rate
With the increasing use of high speed serial links in
commercial systems, the use of the term bit error rate (BER) is
becoming more common place in the serializer- deserializer
community. Even though the basic concept of BER is
generally easy to grasp, there appears to be much confusion
regarding the utility of BER as a system parameter and the
elements affecting BER.The bit error rate is the number of bit
errors divided by the total number of transferred bits during a
studied time interval. BER is unit-less performance measure,
generally expressed as a percentage. The bit error
probability pe is expectation value of BER. The BER can be
considered as an approximate estimate of the bit error
probability (BER). This estimate is accurate for a long time
interval and a high number of bit errors.
G. Estimation of Delay
warning('m is not positive integer');

E=NaN;
return
end
if ((floor(n) ~= n) || (n < 0))
warning('n is not nonnegative integer');
E=NaN;
return
end
if (rho < 0.0)
warning('rho is negative!');
For delay computation for fiber link we have to consider the

pulse spreading due to various types of dispersion in fiber.
The time interruption introduced in optical fiber due to
chromatic dispersion can be calculated as equation (10):
E=NaN;
return
end;
(10)
blocking probability is 0.
Where D is the dispersion coefficient and is the wavelength

assigned for the link with length L. So, delay completely
depends on wavelength assignment value and it provides
better performance than related work [10].
A framework is provided for evaluation of packet delay
distribution in an optical circuit-switched network. The
framework is based on fluid traffic model, packet queueing at
edge routers, & circuit-switched transmission between edge
routers. Packets are assigned to buffers acc. to their
destination, delay constraint, physical route & wavelength. At
every choice epoch, a subset of buffers is allocated to
end-to-end circuits for transmission (Txn), where circuit
holding times are based on limited and exhaustive circuit
allocation policies. To ensure computational tractability,
framework approximates the evolution of each buffer
independently.
%
if (m<=n)
E=0;
return
end
E=1;
for k=1:n,
E=(rho*(m-k+1)*E)/(k+rho*(m-k+1)*E);
end;
E. Relation Between Gain and System Margin

V. RESULTS AND DISCUSSION
The required gain Gonu can be given by equation (9):

(9)
A.
With M, Pr and cir being the system margin, the minimum

received upstream power and the insertion loss from port 2 to
3 of the circulator respectively. The input power to the feeder
fiber is expected to be Pc=3dBm. Then, by substituting
calculated ONU gain to equation (9), calculate the power ratio
between two types of RB for different system reaches, with
104
Simulation Environment Tool
MATLAB (as shown in fig 2) is the

high-performance language for technical computing. It
integrates computing, visualization, and programming in the
easy-to-use environment where problems & solutions are
expressed in familiar mathematical notation. Typical uses
include Math & computation Algorithm development Data
acquisition Modeling, simulation, & prototyping Data

analysis, exploration, & visualization Scientific &
engineering graphics Application development, including
graphical user interface (GUI) building. Although MATLAB
is intended primarily for numerical computing, another
toolbox uses the MuPAD symbolic engine that allowing
access to symbolic computing capabilities. An extra package
Simulink, adds graphical multi-domain simulation &
Model-Based Design for dynamic & embedded systems [13].
Fig 3: Graphical User Interface Window
C. Estimation of Power Ratio

The power ratio between Pcb1 and Pcb2 can be derived
via dividing (1) by (3) or via dividing Pcb/Psb. Note that Fig.
4 is independent of ONU gain and all types of RB powers are
calculated at port 2 of the OLT optical circulator. An
interesting point is that while the carrier RB generated in the
feeder fiber is dominant, signal RB generated in a short
distribution fiber may be comparable with or even larger than
that generated in a long feeder fiber [13].
Fig 2: MATLAB Tool
B. Graphical User Interface

In computing graphical user interface (GUI) is a type
of user interface that allows users to interact with electronic
devices using images rather than text command. GUIs can be
used in computers, hand-held devices such as MP3, portable
media players or gaming devices, household appliances,
office, & industry equipment. A GUI represents information
and actions available to a user through graphical icons &
visual indicators such as secondary (sec) notation, as opposed
to text based interfaces, typed command labels and text
navigation. These actions are usually performed through
direct manipulation of graphical elements. MATLAB apps
are self-contained MATLAB programs with GUI front ends
that automate a task or calculation. The Graphic User
Interface (GUI) typically contains controls such as menus,
toolbars, buttons & sliders. Many MATLAB components,
such as Curve Fitting Toolbox, Signal Processing Toolbox
(DSP), and Control System Toolbox, include applications
with custom user interfaces. A GUI uses a combination of
technologies and devices to provide a platform that the user
can interact with, for tasks of gathering & producing
information as shown in fig 3[14].
Fig 4: Pcb1/Pcb2 for Different Feeder and Distribution Fiber Lengths for
60-km and 40-km Feeder Fibers respectively.
D. The Effect of DIs Extinction Ratio

We have demonstrated that DIs destructive port can
effectively suppress carrier RB, due to its notch filter-like
frequency response. Here we will further study dependence of
carrier RB suppression on DIs ER and optical carriers line
width.
Let ER denote the extinction ratio of DI, coefficients a and b
should fulfil the following conditions (11) and (12):
(11)
(12)
For an ideal DI, (a+b=1). In practice, (a+b) is smaller than 1
due to various reasons, such as unequal coupling ratios of two
couplers in the DI and polarization misalignment.
Nevertheless, (a+b) should be close to 1 for common cases.
Due to this ER, it offers better carrier suppression ratio [8].
E. Blocking Probability-Servers Relation
Blocking probability is the probability in which connection was
not established due to insufficient transmission of data.
Blocking Criteria was used when the design of system was based
on the fraction of calls blocked. If all the devices were occupied,
demand of service was initiated and blocking occurred. For a
system designed on a loss basis, a suitable Grade of Service was
considered in which the percentage of calls lost, were recovered.
This happened due to unavailability of equipment at the instant
of call request. Assume TNCR (m, n, s, d) is the total number of
connection requested for a source (s) and destination (d),

TNCB (m, n, s, d) is the total number of connection blocked,
105
then the blocking probability BP (m, n, s, d) can be defined as
equation (13):
(14)
(13)
Here we have done the analysis by calculating the probability
of blocking after establishing light path connections for a
number of connection requests. Blocking probability is
simply ratio of total number of calls blocked to the total
number of calls expressed in percentage. Minimum blocking
is always desired condition for provisioning. A connection
demands can be blocked either due to the availability of QoS
satisfied path or due to the absence of free light path [9].
.
Fig 7: Channel Load for different wavelengths
In Fig. 7, we present the traffic load varying the different

number of wavelengths of fiber for each link. The approach is
used for time-slot assignment. In the graph, channel load
varies directly with wavelength. As we increase wavelength,
load increases and vice-versa. In this, N is no. of nodes which
is fixed value which we want to use and it also depends upon
length of route which it gets over a network [15].
G. System Margin Vs. Gain
The required gain Gonu can be given by (15):
Fig 5: Blocking Probability for No. of Servers
(15)
Fig 6: Blocking Probability vs Servers
Here, figure 5 & 6 provides a relation between blocking

chance with no. of servers. As no. of servers rise, blocking
probability started decreases and vice versa. Blocking
Probability characterizes in terms of percentage (%). It is
represented in terms of Erlangs. Erlang-B, also known as
Erlang loss formula, is a formula for blocking probability that
describes the probability of call losses for a group of identical
parallel resources [16].
F. Load Vs. Wavelength Relation
Assume N is total no. of nodes, is the wavelength of signal
and L is the length of route, then Load is given by (14):
106
with M, Pr and cir being the system margin, minimum

received upstream power and the insertion loss from port 2 to
3 of the circulator respectively [17].
At the upstream receiver in OLT, the signal-RB beating
noise and signal-amplified spontaneous emission (ASE)
beating noise are dominant. Thus, an attractive feature of the
reach, avoiding the incurred operation complexity of setting
different gains for ONUs with different reaches. The first
graph shows the actual relation while second graph shows the
observed relation between them. This shows the
exponentially increasing curve having increase in gain with
change in system margin. Thus, we can calculate the
maximum system margin and the required optimal ONU gain
for different system reaches. Thus, an attractive feature of
reach. Note that for the scheme employing conventional OOK
in upstream, the variation of optimal ONU gain is 8 dB for a
20-km change in system reach [18].
According to the experimental results in Figure 8 & 9, the
minimum received upstream power needed to achieve BER is
-26.7dBm when L1=50 km, L2=10 km, and Gonu=11dB. The
measured average received power by upstream receiver
module is -18.7 dBm, implying 8 dB system margins. Then
based on (15) we can calculate the maximum system margin
and the required optimal ONU gain for different system

reaches [19]. The theoretical model predicts well the system
performance and thus can be used as a guideline in system
design [20].
relation between BER with noise power. As power increases,

BER decreases and vice-versa as shown in fig 10 [21].
Fig 10: BER-Noise Relation
Fig 8: The maximum system margin and the required optimal ONU gain for
different system reaches.
I.
Output Using Different Length of Fibre
Table 1 shows that effect of wavelength assignment on

various parameters.
Enter the wavelength of signal 1500 nm
No of signals 4
Table 1: Wavelength Assignment Output
Blocking
0.998
0.995
0.99
0.98
2994
2985
2970
2941
Probability
Delay
7.96*10^-42
Rayleigh
Scattering
600
Channel
Fig 9: Gain vs System Power
Load
H. Bit Error Rate Vs. Noise Relation

Enter the wavelength of signal 1520 nm
The bit error rate or bit error ratio (BER) is the number
of bit errors divided by the total number of transferred bits
during a studied time interval. BER is a unitless performance
measure, frequently expressed as a percentage. It is often the
case when measuring low bit error rates (BERs) or measuring
low data rates that direct measurement of BER on a
communication link consumes considerable time. With
slower data rates or improved BERs, the amount of time to
directly measure BER is impractical. As an alternative
approach to directly measuring the BER, it is common to
extrapolate the BER from a few data points that require less
time to measure. It is important to note that due to the random
nature of the noise, the noise levels of the baseline link and the
noise generator are not simply added together when
determining the overall link noise level. The graph shows the
107
No of wavelengths 5
Blocking
0.998
0.995
0.99
0.98
3033
3024
3009
2980
Probability
Delay
Rayleigh
7.55*10^-42
Scattering
Channel
608
Load
VI. CONCLUSION
[15]
This paper investigated the wavelength allocation problem in

WDM network with optical carrier regeneration. The
wavelength transfer problem was transformed into the vertex
colouring problem. An optical delay interferometer at central
office tailors the chirp of the converted upstream signal to
improve the system bandwidth and the dispersion tolerance. It
is proved that results for the transmission through the two hop
networks are successful with reduced BER. The bandwidth of
system can be increased by increasing the capacity of the
system. The capacity of system can be increased by increasing
the number of users without disturbing the working of another
user. If a=0.44 and b=0.4, then it provides extinction ratio of
17 which is useful for providing carrier suppression. It
provides a load of 3 for a wavelength of 10 km. We know that
blocking probability decreases with increase in no. of servers.
Initially, blocking probability is 0.85, then, it started falling.
BER starts increasing with wavelength and also with energy
of signal.
REFFERENCES
[16]
[17]
[18]
[19]
[20]
[21]
[1] G. K. Chang, A. Chowdhury, Z. S. Jia, H. C. Chien, M. F. Huang, J. J.Yu,

and G. Ellinas, Key technologies of WDM-PON for future converged
optical broadband access networks [invited], J. Opt. Commun.
Networks., vol. 1, pp. C35C50, 2009.
[2] N. J. Frigo, P. P. Iannone, P. D. Magill, T. E. Darcie, M. M. Downs, B.N.
Desai, U. Koren, T. L. Koch, C. Dragone, H. Presby, and G. E.
Bodeep, A wavelength-division multiplexed passive optical network
with cost-shared components, IEEE Photon. Technology Lett., vol.
6, no.11, pp. 13651367, Nov. 1994.
[3] M. Feuer, M. Thomas, and L. Lunardi, Backreflection and loss in fiber
loopback networks, IEEE Photon. Technology Lett., vol. 12, no. 8,
pp. 11041108, Aug. 2000.
[4] T. H. Wood, R. A. Linke, B. L. Kasper, and E. C. Carr, Observation of
coherent Rayleigh noise in single-source bidirectional optical fiber
systems, J. Lightw. Technology, vol. 6, no. 2, pp. 346352, Feb.
1988.
[5] P. T. Legg, M. Tur, and Andonovic, Solution paths to limit
interferometric noise induced performance degradation in ASK/direct
detection lightwave networks, J. Lightw. Technology, vol. 14, no. 9,
pp. 19431953, Sept. 1996.
[6] E. Wong, Current and next-generation broadband access technologies,
presented at Opt. Fiber Commun./National Fiber Opt. Eng. Conf., Los
Angles, CA, 2011, Paper NMD1.
[7] N. Suzuki, K. Nakura, T. Suehiro, S. Kosaki, and Nakagawa,
Over-sampling based burst-mode CDR technology for high speed
TDM-PON systems, presented at the Opt. Fiber Commun./National
Fiber Opt. Eng. Conf., Los Angeles, CA, 2011, Paper OTh3.
[8] U. Hilbk, T. Hermes, J. Saniter, and F. Westphal, High capacity WDM
overlay on a passive optical network, Electronic Lett., vol. 32, no. 22,
pp. 21622163, 1996.
[9] E. Wong, K. L. Lee, and T. B. Anderson, Directly modulated selfseeding
reflective semiconductor optical amplifiers as colourless transmitters
in wavelength division multiplexed passive optical networks, J.
Lightw. Technol., vol. 25, no. 1, pp. 6774, 2007.
[10] I. Chlamtac, A. Ganz, and Karmi, Lightpath communications: an
approach to high bandwidth optical WANs, IEEE Trans.
Communication, vol. 40, no. 7, pp. 11711182, July 1992.
[11] M. Matsuura and E. Oki, Multi-carrier distributed WDM ring
network based on reconfigurable optical drop-add-drop multiplexers
and carrier wavelength reuse, in IEEE ICC, Cape Town, South
Africa, 2010.
[12] R. D. Der., y. j. Jhong, Delay-Constraint Survivable multicast Routing
problem on WDM Networks, Communications and Networks in
China, 2010.
[13] B. Ramamurthy., Mukherjee, Wavelength conversion in WDM
networking, IEEE Journal on Selected Areas in Commun., vol. 16,
no. 7, pp. 10641073,1998.
[14] P. J. Urban, A. M. J. Koonen, G. Khoe, and H. Waardt,
Interferometric crosstalk reduction in an RSOA-based WDM passive
108
optical network, J. Lightw. Technology, vol. 27, no. 11, pp.

49434953, Nov. 2009.
T. Yoshida, S. Kimura, H. Kimura, K. Kumozaki, and T. Imai, A new
fiber 10-Gb/s optical loopback method using phase modulation for
WDM optical access networks, J. Lightw Technology, vol. 24, no. 2,
pp. 786796, Feb. 2006.
C. W. Chow, G. Talli, and P. D. Townsend, Rayleigh noise reduction
in 10-Gb/s DWDM-PONs by wavelength detuning and
phase-modulation- induced spectral broadening, IEEE Photon.
Technology Lett., vol. 19, no. 6, pp. 423425, Mar. 2007.
A. Chowdhury, H.-C. Chien, M. Huang, J. Yu, and G. Chang,
Rayleigh backscattering noise-eliminated 115-km long-reach
bidirectional centralized WDM-PON with 10-Gb/s DPSK
downstream and remodulated 2.5-Gb/s OCS-SCM upstream signal,
IEEE Photon. Technology Lett., vol. 20, no. 24, pp. 20812083, Dec.
2008.
C. W. Chow, G. Talli, A. D. Ellis, and P. D. Townsend, Rayleigh
noise mitigation in DWDM LR-PONs using carrier suppressed
subcarrier amplitude modulated phase shift keying, Opt. Expr., vol.
16, no. 4, pp. 18601866, Feb. 2008.
J. Xu and L. K. Chen, Optical phase remodulation for 10-Gb/s
WDM-PON with enhanced tolerance to Rayleigh noise, presented at
OFC, 2010, Paper OThG3.
J. Xu, L. K. Chen, and C. K. Chan, Phase-modulation-based
loopback scheme for Rayleigh noise suppression in 10-Gb/s carrier
distributed WDM-PONs, IEEE Photon. Technology Lett., vol. 22,
no. 18, pp. 13401345, Sep. 2010.
M. Fujiwara, J. Kani, H. Suzuki, and K. Iwatsuki, Impression of
backreflection on upstream transmission in WDM single-fiber
loopback access networks, J. Lightw. Technology, vol. 24, no. 2, pp.
740746, Feb.2006.
Vikas Chhabra, received his B.Tech degree

with Honours in Electronics & Communication
Engg from Ambala College of Engg & Applied
Research, Ambala, Haryana in 2013. Now, He
is pursuing M.Tech in ECE Engg from Galaxy
Global College, Ambala. He has worked in Alfa
Electronics Ltd. as a R&D Engineer from 2013
to 2014. He is Gate 2014 Qualified. His area of
interest is in research work using MATLAB. Mainly fields are optical
networking, wireless networks, Simulink Modelling, Image Processing etc .
Monika Dhiman, received her B.Tech Degree

in Electronics & Communication Engg from
Punjab Engg. College, Lalru in 2011. She
received her M.Tech Degree from Ambala
College of Engg & applied Research, Ambala
in 2013. Now, she is doing a job as Assistant
Professor in ACE, Mithapur. Her area of
Interest is in Optical Communication and
wireless networks. She has published papers in
Optical Networks.

Method and Modelling For Allocating Wavelength in WDM Passive Optical Networks

Uploaded by

Copyright:

Available Formats

Method and Modelling For Allocating Wavelength in WDM Passive Optical Networks

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Method and Modelling For Allocating Wavelength in WDM Passive Optical Networks

Uploaded by

Copyright:

Available Formats

International Journal of Engineering and Technical Research (IJETR)

ISSN: 2321-0869, Volume-2, Issue-10, October 2014