SmartLoop Fire Panels

EN 54-2
EN 54-4
0051-CPD-0225
0051-CPD-0226
0051-CPD-0227
0051-CPD-0228
0051-CPD-0231
0051-CPD-0232
SmartLoop
Analogue fire alarm control panel
Installation manual
Installation manual
Copyright
The information contained in this document is the sole property of INIM Electronics s.r.l. No part may be
copied without written authorization from INIM Electronics s.r.l.
All rights reserved.
European directive compliance

This control panel has been designed and developed to the highest standards of quality and performance
implemented by INIM Electronics s.r.l.
This control panel must be installed in accordance with the instructions described in this manual and in
compliance with the laws in force.
All control panels from the SmartLoop series are EN54-2 and EN54-4 compliant.
All control panels from the SmartLoop series, and all accessory items and special functions have IMQSecurity systems certification, unless otherwise stated.
Copyright
Installation manual
Table of contents
Copyright ............................................................................ 2
European directive compliance ............................................... 2
Table of contents.................................................................. 3
Chapter 1
1.1
1.2
1.3
1.4
1.5
1.6
Chapter 2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
Chapter 3
3.1
3.2
3.3
Chapter 4
4.1
4.2
4.3
4.4
Chapter 5
5.1
5.2
5.3
Chapter 6
6.1
6.2
6.3
Chapter 7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
Table of contents
Introduction......................................................................... 5
Application and use 5
Other parts of the system 7
In order to validate the IMQ-SECURITY SYSTEMS certification, and in compliance
with EN54-2 regulations: 8
About the SmartLoop fire alarm panel series 8
Description of the models 8
Features 9
General information ............................................................ 10

Documentation supplied 10
Manual details 10
Firmware information 10
Operator classification - Access Levels 10
Intellectual property rights 11
Disclaimer 11
Recommendations 11
Testing the system 11
Note to the installer 11
Technical support 11
Conventions 11
Device identification details 12
Warranty 13
Safety laws 13
Device management ........................................................... 15

Product handling and storage 15
Environmental conditions 15
Unpacking the device 15
Technical description........................................................... 16
Panel 16
The motherboard 16
LED panel 18
Technical specifications 19
Accessory devices............................................................... 21
Attachment boards 21
SmartLoop/PRN Printer 25
The SmartLetUSee/LCD and SmartLetUSee/LED Repeater panels 26
Installation ........................................................................ 27
Choosing the mounting location 27
Installation flow, guidelines and testing 27
Connecting the SmartLoop/PRN printer module 28
Connections....................................................................... 29
Note to the Installer regarding wiring and connection compliancy 29
About the circuitry 29
Loop Connections 29
NAC Outputs (Notification Application Circuit) 32
PL Terminal 32
AUX output 33
AUX-R output 33
3
Installation manual
7.8
7.9
7.10
7.11
7.12
7.13
7.14
7.15
7.16
7.17
7.18
Chapter 8
Alarm relay 33
Fault relay 33
Connecting devices to the RS485 BUS 33
Connecting the SmartLoop/NET module 35
Connecting the SmartLoop/INOUT Board 35
Connecting to a PC 36
Connecting a SmartLAN (or SmartLAN/SF) equipped control panel to a PC 37
Connecting a serial printer 37
Batteries 37
Connecting the thermal probe 38
Connecting the mains power source 39
Powering up the system ...................................................... 40
8.1
8.2
Testing wiring integrity 40

First power up 40
Chapter 9
Maintenance ...................................................................... 42
Chapter 10
Troubleshooting ................................................................. 43
10.1
10.2
10.3
10.4
10.5
Appendix
Appendix
Appendix
Appendix
Appendix
A
B
C
D
D
Fault NAC, alarm or fault output trouble 43

LOOP fault 43
Fault on devices connected to the RS485 BUS 44
Battery Fault 44
SmartLoopNET Fault 44
Enea devices...................................................................... 46
Argus Devices .................................................................... 49
Apollo Devices ................................................................... 53
Order Codes ...................................................................... 57
Notes: .............................................................................. 58
Table of contents
Installation manual
Chapter 1
Introduction
Note:
The control panels described in this manual have been designed and developed to the highest standards of
quality, reliability and performance. All product components are capable to application requirements and
able to operate in compliance with the related technical specifications when the temperature external to
their casing complies with Category 3k5 of EN60721-3-3:1995.
Danger:
The GAS control function is not EN54-2 compliant, as this feature is not mentioned in the
aforesaid standard.
Danger:
In order to validate the IMQ-SECURITY SYSTEMS certification, and in compliance with EN542 regulations, all the manual alarm buttons and fire detectors employed in the system must
be associated with fire detection and alarm functions.
1.1
Application and use
The SmartLoop analogue-addressable fire alarm panel manages up to eight loops. The SmartLoop is
capable of working in a network environment (maximum configuration 30 nodes arranged in a token ring).
The loops accommodate different types of fire-security devices (detectors, input and output modules,
callpoints, fire bells, etc.). The maximum loop wire length is 2000 m. The SmartLoop also provides
supervised outputs which guarantee full control of peripheral device functions (e.g. fire bells). The panel
identifies and signals alarm, pre-alarm, fault, early warning, bypassed zone, test and monitoring
conditions. The system status is indicated on the display and on the system status LEDs. The SmartLoop
panel supports up to 14 Repeater panels (accessory items) which replicate system signals/data and allow
building occupants with Level 2 authorization to silence and reset the system. The panel can also be
connected to a PC or printer.
The self-addressing feature and reduced-complexity point programming allow fast and easy installation.
E
B
C
PSTN
line
Internet
D
Figure 1 - Example configuration: 6 node token-ring network layout (Hornet)
Introduction
Installation manual
[A] Loop
All the peripheral devices of the system must be connected in parallel to the loop circuit (2 pole STP). The
loop is a closed electrical circuit in which a wide variety of alarm devices can be accommodated. Opening or
closing the circuit at any point will generate a fault signal. The loop circuit communication path starts on
the Loop-Out terminals and ends on the Loop-In terminals. The panel controls and communicates with the
loop devices via digital protocol. The loop utilizes the same two poles for the power supply to the system
devices and the two-way communication channel. The loop accommodates:
1. Detectors: A smoke detector is an active fire protection device that detects smoke or flames and
issues an alarm thereby alerting building occupants to the danger of fire. Detectors can be:
- Optical smoke detectors which look for the presence of visible by-products of combustion in the
detection chamber (Tyndall effect).
- Optical/Heat detectors which operate as per optical smoke detectors but also sense for increase in the
environment temperature. The combination of both sensing methods (smoke and heat) provides faster
detection and reduces the false alarm rate.
- Heat detectors: sense for an increase in the temperature in the protected environment. There are two
types of heat detector: Fixed temperature that signal alarm when the temperature exceeds the
predefined threshold; and Rate-of-rise which, as well as monitoring the predefined fixed temperature,
also respond to rapid increase in temperature.
- Ionization smoke detectors: feature a harmless radioactive source within a dual detection chamber.
They operate by sensing for a change in electrical conductivity across the detection chamber.
- CO detectors: sense the levels of carbon monoxide given off by all carbon-based materials in the
smoldering stages of a fire (often combined with heat detection sensor).
2. Input Module: a device which monitors the status of another device (callpoint, detector, etc.) and
sends the respective information to the panel. The Input module allows the loop to accommodate any
type of device.
3. Output Module: provides a supervised ancillary output. The cause of activation of this output can be
defined during the system configuration phase. The output module interfaces all types of loop devices
(bells, signaling devices, fire door magnets, etc.).
4. Callpoint: a clearly labeled fire button with instructions for use in the event of fire. Usually placed near
building entrances/exits. These push-button alarm-trigger devices allow building occupants to activate
system alarms.
5. Sounder/Flasher: audible/visual alarm signaling devices.
For the list of the devices the loop accommodates, and for details regarding their wiring and operating
principles, refer to Appendix A - Enea devices, Appendix B - Argus Devices and Appendix C - Apollo
Devices.
The loop circuit configuration (as required by the local Fire code in force) is a fault-tolerant circuit which, in
the event of short-circuit or loop interruption, allows the panel to continue to communicate and drive the
elements on either side of the interruption.
Isolator
In order to provide a fault-tolerant loop circuit that is Fire code compliant, isolator modules must be
installed in series with the loop circuit. Isolators modules detect short-circuit conditions and consequently
interrupt the loop circuit. If a short-circuit occurs, the two isolators adjacent to the shorted section will
open and split the loop in such way as to allow the panel to drive the elements on either side of the
interruption. No more than 32 detectors/devices should be installed between two isolator modules.
Note:
Many detectors/devices have built-in isolators and therefore do not require isolator modules. Refer to
Appendix A, Appendix B and Appendix C for further details.
[B] Repeater SmartLetUSee/LCD (accessory item)

This optional system enhancement tool (equipped with keypad, LEDs, fast buttons and display) replicates
all the system data. The panel supports 14 repeaters connectable via RS485 BUS (maximum cable length
1000m from panel). Repeaters should be located at building entrances/exits in such way as to allow
persons in charge to view the system status without going too far inside the building.
[C] SmartLevel power-supply stations (accessory item)
The SmartLevel is the ideal power source for all devices located in the area protected by the detection
system. Its internal board satisfies all EN54 requirements and provides complete supervision of the power
6
Introduction
Installation manual
station. The device can be connected to the control panel loop via an input/output module (not included),
installed inside the box, or by means of the RS485 BUS, thus allowing the complete supervision of the
power station and control of the 3 outputs.
[D] SmartLine-EXT fire-extinction panel (optional)
SmartLine-EXT fire-extinction panels are based on SmartLine conventional fire detection panels (4-zones).
These control panels provide all the functions of SmartLine conventional fire-detection panels plus 1
SmartLetLoose/ONE extinction channel.
They interface with SmartLoop control panels via a built-in RS485 BUS. It is possible to programme the
SmartLine-EXT fire-extinction control panel to activate its functions in response to local data/signals
(conventional zones, extinguishant terminals, Stop extinction, etc.), or in response to remote data/
signals coming from the SmartLoop control panel.
[E] Sounderflashers
These audible/visual signaling devices connect to the control panel outputs and activate when specific
conditions occurs. The cause of activation (alarm, pre-alarm, early warning, etc.) can be defined during the
system configuration phase.
1.2
Other parts of the system
Point: synonym and definition of a loop device (detector, etc.).

Zone: a group of points (detectors, etc.). The points can be assigned to the zones during the configuration
phase. Consult your local Fire code for the rules regulating automatic fire detection installations and for full
details regarding zone limitations.
Power Supply: a module, connected to the mains 230 Vac, that provides a stabilized voltage @ 24 V
(27.6 V) to the system and the charge source to the batteries. The EN54-4 compliant power-supply module
is housed below the motherboard. The mains voltage (230 Vac) is the primary power source of the system.
Refer also to paragraph 7.18 Connecting the mains power source.
Batteries: the secondary power source of the system. The panel houses two lead batteries @ 12V 17Ah
(connected in series). The system monitors the battery status (efficiency and charge). In the event of
inefficient or low battery conditions, the system will signal battery fault. If primary (230 Vac) power failure
occurs, the batteries will take over, however, they will shutdown automatically if the blackout persists. The
automatic battery shutdown feature prevents irreparable damage to the batteries. Refer also to paragraph
7.16 Batteries.
Thermal probe: an accessory tool, to be connected to the panel and attached to the battery pack. This
device monitors the temperature of the external battery pack and regulates the battery charge accordingly.
Refer also to paragraph 7.17 Connecting the thermal probe.
RS485 Bus: 4 wire BUS for the Repeater connections. Four pole twisted shielded cable must be used for all
connections. Refer also to paragraph 7.10 Connecting devices to the RS485 BUS.
Timer: a logical entity (the panel provides 8 timers) for automatic time-management of preset intervals (2
intervals per day) on preset days of the week and specific dates. The timers can be used in equations and/
or to manage predefined operations.
Equation: a group of logical conditions defined by the installer. An equation comprises a series of
operators (AND, OR, +, etc.) and a series of operands (Points, Zones, Timers, etc.). An equation can be
associated with an output that will activate when the equation is satisfied.
Holidays: a list of days defined during the system configuration phase that can be associated with the
timers.
Early Warning: a signal generated by detectors with the early-warning feature (to be defined during the
system configuration phase). The detector senses for a level of smoke or heat that exceeds its early
warning threshold (each detectors can be set separately). This signal indicates that the person/s
responsible for the safety of the building and its occupants should verify the alarm or check the
functionality of the detector concerned.
Introduction
Installation manual
1.3
In order to validate the IMQ-SECURITY SYSTEMS certification, and in

compliance with EN54-2 regulations:
All the manual alarm buttons and fire detectors employed in the system must be associated with fire
detection and alarm functions.
The functions associated with the programmable LEDs on the control panel frontplate (Keypad/Display
board and LED board), and on SmartLetUSee/LCD and Smart LetUSee/LED Repeaters must be set up in
accordance with the colour of the LEDs.
- Red: fire alarm
- Yellow: fault, test and disabled status
Note:
1.4
The GAS control function is not EN54-2 compliant, as this feature is not mentioned in the aforesaid
standard.
About the SmartLoop fire alarm panel series
There are 3 expandable models (expandable to 8 loops by means of 3 SmartLoop/2L expansion boards). All
have 2 loops and are housed in the same sized enclosure. Each expandable model has a technicallydownsized version (in same-sized enclosure) with 1 loop for reduced complexity applications.
All models manage the same functions and support a full spectrum of hardwired and wireless devices.
The SmartLoop fire alarm panel series provides the following models:
SmartLoop1010/P - fully-equipped frontplate model with 1 loop
SmartLoop2080/P - fully-equipped frontplate model with 2 loops expandable to 8
SmartLoop1010/G - keypad and display model with 1 Loop
SmartLoop2080/G - keypad and display model with 2 loops expandable to 8
SmartLoop1010/S - flush front model with 1 loop
SmartLoop2080/S - flush front model with 2 loops expandable to 8
SmartLoop1010/P
SmartLoop1010/G
SmartLoop1010/S
SmartLoop2080/P
SmartLoop2080/G
SmartLoop2080/S
Figure 2 - SmartLoop Series
1.5
Description of the models
The /P model is equipped with a keypad, display, fault LEDs, fast buttons and a Zone status LED pad.
This model is suitable for locations where extended visual signals and manual control are necessary. This
model can be enhanced with the SmartLoop/PRN thermal printer (accessory item).
Introduction
Installation manual
The /G model is equipped with a keypad, display, fault LEDs and fast buttons and is suitable for
installation in locations where visual signals and manual control are necessary. This model can be upgraded
at any time after installation (for example, if moved to a location where extended visual signals and
manual control are necessary) by replacing its door with a /P model door that is enhanced with a Zone
status LED pad and thermal printer option.
The /S model has an unequipped door (no keypad, display or LEDs) and is suitable for installation in
locations where visual indications and manual control are not required (e.g. basements). This model can
be upgraded at any time after installation (for example, if moved to a location where visual signals and
manual control are necessary) by replacing its door with a /G model or /P model door.
1.6
-
Features
Manages up to 240 zones per panel with network-zone architecture feature

Network environment capable (maximum configuration 30 panels)
Group and Zone sharing among panels in the network environment
Switching power supply 27.6 V @ 4 A with battery charger function
2 on-board loops on expandable 2080 models; 1 on-board loop on non-expandable 1010 models
3 programmable NAC outputs
1 Alarm NAC output
1 Fault NAC output
1 alarm signalling relay (voltage free)
1 fault signalling relay (voltage free)
RS485 BUS for the connection of up to 14 SmartLetUSee/LCD repeaters, 4 SmartLevel power stations
and 4 SmartLineEXT fire-extinction stations
1 power supply output @ 24 V for external devices
1 power supply output @ 24 V for external devices with "Power Cutoff" during reset
RS232 and USB connectors for uploading/downloading programming data
2000 event buffer
The motherboard provides housing for:

-
3
1
1
1
1
1
1
SmartLoop/2L loop expansion boards with 2 loops per board (2080 expandable models only)
SmartLoop/NET network board
SmartLAN or SmartLAN/SF board
SmartLoop/PSTN board
SmartLoop/INOUT Input/Output expansion board
SmartLoop/LED zone-status LED module (for /P models only)
SmartLoop/PRN thermal printer module (for /P models only)
Note:
Introduction
The 1010 non-expandable models with 1-loop have exactly the same features and components as the
2080 expandable models with 2-loops.
Installation manual
Chapter 2
General information
2.1
Documentation supplied
Installation manual (this manual)

Programming Manual
User Manual
The manuals are supplied with the device. For further copies of the Installation Manual, please contact
INIM Electronics s.r.l. offices quoting the order number shown in Appendix D - Order Codes.
2.2
Title: SmartLoop Installation Manual

Version: 3.02
Month and year: April 2012
Code: DCMIINE0SLOOP
Addressee: installer, technical assistance operator
2.3
Manual details
Firmware information
SmartLoop firmware version: 2.0.x

SmartLoop loop driver firmware version: 2.0.x
SmartLoop Front Panel Firmware version: FSANN 1.0.x
SmartLAN/SF firmware version: 4.1.x
SmartLAN/SF firmware version: 1.0.x
SmartLoop/PSTN firmware version: 1.0.x
SmartLoop/2L firmware version: 2.0.x
SmartLoop/INOUT firmware version: 2.0.x
SmartLetUSee/LCD firmware version: 1.0.x
SmartLetUSee/LED firmware version: 1.0.x
2.4
Operator classification - Access Levels
Level 1
All building occupants can view the system status (active events) and events log and silence the panel
beeper.
Level 2
ONLY authorized keyswitch users and PIN users (5 digit codes) can Enable/Disable loop devices, bell outputs,
software zones and network devices, and SILENCE or RESET the system.
Level 3
ONLY authorized technicians, appointed by the Installer company can, by means of a screw driver, remove
the screws and open the fire control panel enclosure to insert the J2 Jumper and then, after entering a 5
digit PIN (5 digit code) access the parameter programming phase and/or carry out maintenance work (for
example, change the battery, replace fuses, etc.).
Level 4
ONLY authorized technicians, appointed by the Manufacturer can, by means of special tools, carry out
repair work on the motherboard (for example, repair or replace SM components).
Note:
10
The default PIN code is 00004.
General information
Installation manual
2.5
Intellectual property rights
The information contained in this document is private property. All rights reserved
No part of this document may be copied or reproduced unless expressly authorized in writing by INIM
Electronics, in particular the parts regarding the device specified in paragraph 4.1 Panel.
2.6
Disclaimer
INIM Electronics s.r.l. shall not be responsible for damage arising from improper application or use.
This control panel should be handled by qualified personnel only. Installation must be carried out strictly in
accordance with the instructions described in this manual, and in compliance with the local fire code in
force.
2.7
Recommendations
INIM Electronics recommends that the entire system be tested on a regular basis (refer to paragraph 2.8
Testing the system).
2.8
Testing the system
This system has been designed to the highest standards of quality and performance. The system may fail
to function as intended due to the failure of a component. Most problems which prevent a fire control
system from operating as intended can be found by regular testing and maintenance of the system devices
(refer to Chapter 9 - Maintenance).
Testing should include all detectors, signaling devices and any other operational devices that are part of the
system.
2.9
Note to the installer
In order to provide adequate protection and instructions for proper use, you (the installer) must be familiar
with the operating procedure of this device. As the only individual in contact with system users, it is your
responsibility to instruct them on how to use this system properly and to bring to their attention that every
fire is different in the amount of smoke and rate of burning. Therefore, smoke and heat detectors may not
provide timely warning of fires caused by violent explosions, escaping gas or improper storage of
inflammable materials.
Regardless of its capabilities, a fire alarm system is not a substitute for the necessary precautions building
occupants must take to prevent or minimize the harmful effects of fire.
2.10
Technical support
Our professional engineers are readily available to assist you. Call our phone number and you will be
connected right away to a person who will answer all your questions and provide you with full technical
support.
2.11
Conventions
2.11.1 Glossary and terminology

Panel, device, system: refer to the items described in paragraph 4.1 Panel.
Left, right, behind, above, below: refer to the directions as seen by the operator in front of the mounted
device.
Communicator (telephone, SMS, digital): synonym of dialer.
STP: synonym of shielded twisted pair cables
Qualified personnel: those persons whose training, expertise and knowledge of the laws and bylaws
regarding service conditions and the prevention of accidents, are able to identify and avoid all possible
situations of danger.
Select: click on and select a specific item (from drop-down menu, options box, graphic object, etc.).
Press: click on a video button, or press a key on the panel keypad.
General information
11
Installation manual
2.11.2 Graphic conventions

Following are the graphic conventions used in the text.
Conventions
Example
description
Refer to paragraph
Text in Italics
Text in italics: indicates the title of a chapter, section, paragraph, table

or figure in this manual or other published reference.
2.11.2 Graphic
conventions
<text>
#<CustomerCode>
Variable data.
[uppercase
letter] or
[number]
[A] or [1]
Representation of a part of the system or video object.
BUTTON
CANC, ESC, RESET
Computer or control panel keys.
Note:
The attached notes contain important information about the text.
Attention:
The "Attention" prompts indicate that total or partial disregard of the procedure could
damage the connected devices.
Danger:
The danger warnings indicate that total or partial disregard of the procedure could injure the
operator or persons in the vicinity.
2.12
Device identification details
MADE IN ITALY
0051-CPD -0231
LBDTIN4ASLOOP11G
1010/G 02/2012
230V~ -15% + 10%
Alimentazione /
Power / Alimentacion
50/60 Hz
Consumo /
0.9 A
Consumption / Consumo
Isolamento /
Classe I
Isolation / Aislamiento
Approvato /
EN54-2, EN54-4
Approved / Aprobado
Figure 3 - Data labe
0051
0051
0051
0051
09
0051 - CPD - 0228
Control and signalling system with integrated
power-source.
SmartLoop/1010-S
09
0228
0051 - CPD - 0231
power-supply device.
SmartLOOP/1010-G
SmartLOOP/1010-S
09
0051 - CPD - 0232
SmartLOOP/1010-P
EN 54-2:1997+A1:2006
EN 54-4:1997+A1:2002+A2:2006
Isolation: Class I
Options with requirements:
- 7.8 Sounder circuits output
- 7.11 Delayed outputs
- 7.12 Alarm on two points activation
- 8.3 Fault from points signal
- 8.9 Monitored output for remote signalling
- 9.5 Points isolation
- 10.0 Test condition
Manufacturer: INIM Electronics s.r.l.

Address: via Fosso Antico, Centobuchi
63076, Monteprandone (AP), Italy
12
EN54-4: 1997/ A2: 2006

EN54-4:
1997/ A1: 2006
EN
54-2:1997+A1:2006
Isolation:
Class I
EN
54-4:1997+A1:2002+A2:2006
Options with
requirements:
Isolation:
Class
I
- 7.11 Delayed
outputs
Options
with requirements:
7.12Sounder
Alarm on
two points
- 7.8
circuits
outputactivation
8.3 Fault
fromoutputs
points signal
- 7.11
Delayed
8.9 Monitored
output
for remote
signalling
- 7.12
Alarm on two
points
activation
9.5 Fault
Pointsfrom
isolation
- 8.3
points signal
10.0Monitored
Test condition
- 8.9
output for remote signalling
INIM Electronics s.r.l.
-Manufacturer:
10.0 Test condition
EN 54-2:1997+A1:2006
EN 54-4:1997+A1:2002+A2:2006
Isolation: Class I

General information
Installation manual
0051
0051
0051
0051
09
0051 - CPD - 0225
SmartLOOP/2080-S
09
0051 - CPD - 0226
SmartLOOP/2080-G
09
0051 - CPD - 0227
0228
SmartLOOP/2080-P
SmartLOOP/1010-S
EN 54-2:1997+A1:2006
EN 54-4:1997+A1:2002+A2:2006
Isolation: Class I
EN 54-2:1997+A1:2006
EN 54-4:1997+A1:2002+A2:2006
Isolation: Class I




EN54-4: 1997/ A2: 2006

EN54-4:
1997/ A1: 2006
EN 54-2:1997+A1:2006
Isolation:
Class I
EN 54-4:1997+A1:2002+A2:2006
Isolation:with
Class
I
Options
requirements:
-Options
7.11 Delayed
outputs
with requirements:
7.12Sounder
Alarm on
two points
- 7.8
circuits
outputactivation
- 7.11
8.3 Fault
fromoutputs
points signal
Delayed
8.9 Monitored
output
for remote
signalling
- 7.12
Alarm on two
points
activation
- 8.3
9.5 Fault
Pointsfrom
isolation
points signal
- 8.9
10.0Monitored
Test condition
output for remote signalling
Manufacturer:
INIM Electronics s.r.l.
Figure 4 - CE Mark
2.13
Warranty
INIM Electronics s.r.l. warrants the original purchaser that for a period of 24 months from the date of final
acceptance, the product shall be free of defects in materials and workmanship. The warranty applies only
to defects in parts and workmanship relating to normal use. It does not cover:
Improper use or negligence
Damage caused by fire, flood, wind or lightning
Vandalism
Fair wear and tear
INIM Electronics s.r.l. shall, at its option, repair or replace any defective products. Improper use, that is,
use for purposes other than those mentioned in this manual will void the warranty. For the full details and
conditions regarding the warranty, refer to the purchase order.
2.14
Safety laws
The aim of the instructions in this section is to ensure that the device is installed and handled properly. This
chapter contains vital information. The installer should be familiar with this section and bring each item to
the attention of the system users.
2.14.1 Compliancy
The design and manufacture of the SmartLoop panel comply with EN 54-2 Fire detection and signaling
systems - Control and signaling panels.
The design and manufacture of the power supply comply with EN 54-2 Fire detection and signaling systems
- Power supply devices.
2.14.2 Managing electronic devices

The normal motions of any person may generate electrostatic potential of thousands of volts. Discharge of
this current through semiconductor devices during handling may cause serious damage which although
may not be immediately evident may reduce the reliability of the circuits.
If located in their housings, the electronic circuits of INIM Electronics products are highly immune to
electrostatic discharge.
Do not expose the circuits to damage by removing the modules unnecessarily from their housings.
General information
13
Installation manual
1. When removing or handling the boards, hold the board edges only.
2. Do not touch the electronic components, the printed circuits or the metal parts of the connectors.
3. Do not hand the module to another person without first ensuring that you both have the same
electrostatic potential. This can be achieved by simply shaking hands.
4. Place the board on an anti-static surface or a conductor surface with the same potential.
Further information regarding procedures relating to safety when working with electronic devices can be
found in Directive IEC 60147-0F.
2.14.3 Connecting the apparatus

In order to provide adequate protection and instructions for proper use, security professionals (Installers
and maintenance technicians) must be familiar with the operating procedure of this device.
Please read the instructions carefully before installing and/or servicing the system.
Before first power-up, be sure that the earth connection has been completed properly on the respective
terminal.
The recommended minimum wire cross section for the earth connection is 2.5 mm2, that is, unless
otherwise stated in accessory documentation.
2.14.4 Replacement and disposal of used devices

Replacement
When replacing used devices, disconnect the devices concerned then complete the connections of the new
devices in compliance with the instructions printed on the respective leaflets.
Contact your local municipal offices for information regarding the disposal of used electronic devices.
Disposal
Do not burn used electronic devices, or allow them to pollute the environment (countryside, rivers, etc.).
Electronic devices must be disposed of in a safe environment-friendly way. In order to avoid short-circuits,
take all the necessary precautions when removing used batteries. Contact your local municipal offices for
information regarding the disposal of batteries.
14
General information
Installation manual
Chapter 3
Device management
3.1
Product handling and storage
This device is safely packed inside a cardboard box, however, care must be taken to avoid accidental
damage during handling. Cartons/boxes should be placed in such a way as to avoid knocks and falls, and
special care must be taken to protect the devices from extreme heat and/or cold.
3.2
Environmental conditions
Temperature limits:
-10 / +55C for transport and storage
-5 / +40C operating temperature
3.3
Unpacking the device
Take due care when unpacking the product, and dispose of all waste packaging in accordance with the local
method of disposal.
The cardboard box contains the SmartLoop control panel (enclosure in metal).
Note:
3.3.1
All waste packaging must be disposed of in full respect of the local laws in force.
Inside the box
Inside the box you will find

Metal enclosure containing the motherboard
Installation Manual
Plastic bag containing: resistors, diodes, 2032 lithium battery (non-rechargeable), keys, battery
connection wires
Attention:
The 2032 lithium battery guarantees data retention. This battery must be fitted properly into
its housing (refer to paragraph 4.2 - [H]) with the + sign towards you.
The package does not include:

a thermal probe (an accessory device which monitors the temperature of the external battery pack and
regulates the battery charge accordingly), batteries, the SmartLeague software CD. These items must be
purchased separately. Be sure you have these items on hand before starting the installation procedure.
Attention:
In order to validate the IMQ-SECURITY SYSTEMS certification and comply with EN 54-4
requirements, installation of a thermal probe is essential.
Be sure you have this item on hand before starting the installation procedure.
Device management
15
Installation manual
Chapter 4
Technical description
4.1
Panel
E
D
A
C
F
B
G
E
Figure 5 - Overview
[A]
Front panel with display, keys and signalling LEDs
[B]
Key location for the Level 2 access key
[C]
LED panel
[D]
SmartLoop/PRN Thermal printer
[E]
Securing screws for the front cover
[F]
Cable entries (located on all sides of the enclosure)
[G]
Data label
4.2
SmartLoop/P and SmartLoop/G only
SmartLoop/P only
All models
The motherboard
The SmartLoop motherboard has a 32 bit microprocessor that controls all the control panel functions, and
2 peripheral microprocessors (one per loop) that manage communications with the system peripherals.
INIMs R & D professionals have developed and designed the SmartLoop motherboard using groundbreaking new generation fire technologies that ensure maximum precision and performance. Deployment
of the most advanced reflow technology ensures high-noise immunity and extreme accuracy. Each
connection terminal is protected against electrical surges and is high-noise immune capable. All terminals
on the motherboard are clearly marked and easily identifiable.
The motherboard has been especially designed to accommodate with ease the various SmartLoop
attachment boards.
16
Installation manual
G
F
B
Q
R
A6
A5
A4
A3
A2
A1
Figure 6 - About the motherboard

[A]
Connector for the connection with the display board (located on the frontplate)
[B]
Loop 1 status LED
[C]
Loop 2 status LED
[D]
SmartLoop/2L board connector
[E]
SmartLAN board connector
[F]
Microprocessor reset button
[G]
Memory jumper (if removed and the panel is switched Off, the system will restore to factory default settings)
[H]
Memory battery (3 V lithium battery)
[I]
RS232 COM connector (DB9 male)
[J]
USB connector (type B)
[K]
SmartLoop/PSTN plug-in module connector
[L]
Clear ground-fault jumper (removal of this jumper clears ground faults)
[M]
On-panel thermal printer connector
[N]
Programming jumper (removal of this jumper blocks access to programming)
[O]
ProbeTH Thermal probe board connector (Thermal probe not included)
[P]
Switching power-supply module connector
[Q]
SmartLoop/NET plug-in module connector
[R]
Connector for internal batteries (connection wire included)
[S]
SmartLoop/INOUT plug-in module connector
17
Installation manual
[T]
PL
PL and GND terminals for disconnected-battery signalling In the event of primary and
secondary power failure (mains and batteries), the PL terminal will connect to GND. Under
normal operating circumstances, the PL terminal is disconnected.
[U]
AUX
24V output for the external power load, protected by a 1.8A self-resettable fuse
[V]
AUX-R
24V output for external loads, protected by a 1.8A self-resettable fuse (with "Power Cutoff"
during reset.) Suitable for powering devices which require power loss in order to reset (e.g.
beam detectors)
[W]
RS485
REPEATER
RS485 Bus terminals for repeater connections (accommodate up to 14 Repeaters)
[X]
ALARM
RELAY
Alarm relay (voltage free)
[Y]
FAULT
RELAY
Fault relay (voltage free)
[Z]
FAULT OUT
Supervised fault output protected by 1A fuse
[A1]
ALARM NAC
Supervised alarm NAC output protected by 1A self-resettable fuse
[A2]
NAC1,
NAC2,
NAC3
Programmable NAC outputs protected by 1A self-resettable fuse
[A3]
LOOP2-I
Loop 2 Input terminals
[A4]
LOOP2-O
Loop 2 Output terminals
[A5]
LOOP1-I
[A6]
LOOP1-O
4.2.1
Loop status LED
The loop status LEDs (paragraph 4.2 - [B] and paragraph 4.2 - [C]) provide visual information relating to
the communications between the control panel and its detectors. They indicate that the panel is
interrogating its devices, the protocol it is using and whether or not the interrogated devices have
responded.
The green LED on the right will flash each time a loop device responds. The control panel interrogates its
devices at regular intervals, starting from address 1 through to the last address (for information
regarding which devices can be connected to the loop, refer to Appendix A, Appendix B and Appendix C).
The red LED in the centre will blink each time a command is sent through the loop for a device using
either Enea (Appendix A) or Argus (Appendix B) protocol.
The red LED on the right will flash each time a command is sent through the loop for a device using
Apollo (Appendix C) protocol.
Under normal operating conditions, the red LED (relating to the protocol in question) will blink rapidly and
the green LED will flicker indicating the device response. The flickering phase depends on the number of
devices connected to the loop. The more devices the longer the LED will flicker.
4.3
LED panel
SmartLoop/P control panel models are equipped with a LED panel (located on the front of the control panel
enclosure) which is connected to the keypad/display board (paragraph 4.1 - [C]).
This panel has 48 red LEDs which provide one or more signals (configured during the programming phase).
The On/Off logic of each LED can be set up individually.
18
Installation manual
4.4
Technical specifications
Operating voltage
230 Vac -15% + 10% 50/60Hz
Max current draw on AC input
0.9 A @ 230Vac
Internal power supply output voltage
27.6 Vdc
Internal Power supply MAX current
4A
Internal Power Supply output ripple
MAX 1%
Max current available for the external load (loop devices, external
loads, attachment boards, etc.)
2.8 A
Minimum current (Imin)
600 mA
Low Voltage range
18 ... 27.6 Vdc
Panel Current draw (motherboard+LCD screen on the frontplate)

- standby
200mA
- from battery in the event of mains failure
80 mA
- maximum battery-charge current
1A
Battery specifications
12 V @ 7Ah or 12 V @ 17Ah
(Brand and type)
YUASHA (or equivalent)

NP 7 -12 FR or NP 17 -12-FR or similar
Flame Class UL94-V2 or higher
Maximum internal resistance of the batteries (Ri max)
2.2 Ohm
Operating temperature
From -5 to +40 C
Dimensions (Height x Length x Depth)
48 x 47 x 13.5 cm
Weight without battery
8 Kg
Attachment board current draw

SmartLoop/2L (2 Loop expansion board)
stby: 20mA MAX:70mA
SmartLoop/INOUT (6 input/output expansion board)
stby:40mA MAX:300mA
SmartLoop/NET (Token-ring network adaptor board)
stby: 40mA MAX:40mA
SmartLoop/PSTN (PSTN dialler)
stby:20mA MAX:60mA
SmartLAN (Ethernet board)
stby:200mA MAX:200mA
SmartLoop/LED (48 LED board)
stby:40mA MAX:80mA
SmartLoop/PRN (on-panel thermal printer)
stby:0 MAX:1A
SmartLetUSee/LCD (LCD repeater)
stby: 40mA MAX:50mA
SmartLetUSee/LED (LED repeater)
stby: 5mA MAX:50mA
Absolute maximum terminal ratings
19
Installation manual
Motherboard
Loop output terminals
Max 0.5 A each loop
NAC1, NAC2, NAC3, alarm NAC, fault output
1.3 A MAX
Fault relay, alarm relay
Voltage-free contact 5A @ 30V max
RS485 BUS
1.8 A MAX
AUX, AUX-R
1.8 A MAX
Current ripple on AUX and AUX-R outputs
1% MAX
PL
Normally Open Contact 5A @ 30Vdc MAX
SmartLoop/INOUT
on each CH
PIN code to access default settings
20
0.9 A MAX
00004
Installation manual
Chapter 5
Accessory devices
5.1
Attachment boards
The motherboards accommodates the following attachment boards:
Figure 7 - The motherboard accessorized with attachment boards

[A]
Up to 3 SmartLoop/2L loop expansion boards (2080 expandable models only)
[B]
1 SmartLoop/NET network board for the creation of a control panel network environment (Hornet
technology)
[C]
1 SmartLAN LAN board for connection to an Ethernet (Janus technology)
[D]
1 SmartLoop/PSTN telephone board for PSTN land line connection
[E]
1 SmartLoop/INOUT input/ouput expansion board (provides 6 Inputs/Outputs)
SmartLoop/P models also accommodate the SmartLoop/PRN thermal printer (to be located on the
frontplate). This device provides real-time printouts and enquiry printout.
Refer to the respective paragraphs for the board descriptions.
5.1.1
The SmartLoop/2L board
All expandable SmartLoop control panels have 2 on-board loops expandable to 8 by means of 3
SmartLoop/2L expansion boards. The non-expandable SmartLoop 1010 version have 1 loop only.
The loops accommodate either 126 or 240 fire detection/signalling devices, depending on the selected
protocol (refer to Appendix A, Appendix B and Appendix C).
Due to electrical incompatibility, different brand devices (i.e. devices using different protocols) cannot coexist on the same loop. However, the loops can be programmed separately in such way as to allow the
system to manage different brand devices on different loops.
Accessory devices
21
Installation manual
Loop 1 status LED
[B]
Loop 2 status LED
[C]
SmartLoop/2L board to board connector (up to 3

boards)
[D]
Motherboard to SmartLoop/2L board connector
[E]
[F]
[G]
[H]
[I]
Screw locations
refer to paragraph
4.2.1 Loop status LED
[A]
Figure 8 - The SmartLoop/2L board

The SmartLoop/2L package includes:
A cable for the connection to the motherboard

Two split ferrite cores for the loop output wires
5 anchor screws
5 spacers
5.1.2
The SmartLoop/NET board
The SmartLoop/NET board allows you to create a token-ring capable of managing 30 SmartLoop control
panels via a 3 -pole cable.
The network must be wired as a ring network with a maximum cable length between each panel of 2000
metres, in this way, the network will be fault tolerant (HorNet technology). Using a supplementary 2-pole
cable (5 poles in all), you can create a protection ring which can pass alarm conditions, coming from a fire
control panel with microprocessor fault, through the ring.
[A]
A terminals for the protection-ring connection (to be connected to

Alarm-B of the successive control panel)
[B]
Communication Port A (to be connected to Port-B of the successive

control panel)
[C]
B terminals for the protection ring connection (to be connected to

Alarm-A of the previous control panel)
[D]
Communication Port B (to be connected to the Port-A terminals of

the previous control panel)
[E]
Blue LED (indicates the In Service/Out of Service status of the

SmartLoop/NET board). If this LED is Off, the panel is isolated from
the network.
[F]
2 Port A status LEDs (green and yellow)
[G]
2 Port B status LEDs (green and yellow)
[H]
Interface to motherboard plug (on the reverse side of the board)
[I]
Screw locations
I
B
Figure 9 - SmartLoop/NET board

22
Accessory devices
Installation manual
Danger:
In order to allow the ring to operate properly, the Port-B and Alarm-B terminals must be
connected to the successive Port-A and Alarm-A terminals.
The SmartLoop/2L package includes:

4 anchor screws
4 spacers
5.1.3
The SmartLAN board
The SmartLAN board connects to any Ethernet network and allows remote access (via Internet) to the fire
control system (allows connection to all the fire control panels in the token-ring network).
SmartLAN This board can send detailed e-mails for each event and real-time event reports over TCP/
IP. It provides a web server for web-based access to the system via browser (Internet Explorer, Firefox,
Opera, etc.).
This board allows you to carry out remote programming operations (upload/download), manage the
system via INIM's SmartLook software application and also manage Dynamic DNS.
SmartLAN/SF This board allows you to carry out remote programming operations (upload/download),
manage the system via INIM's SmartLook software application.
To access the configuration phase of the SmartLAN board, the default IP address is: 192.168.1.92
J
G
[A]
Microprocessor reset button
[B]
Programming reset button
[C]
Ethernet port
[D]
Power-supply indicator LED
[E]
Motherboard communication LED (SYS)
[F]
LINK LED (indicates currently active Ethernet

communication)
[G]
ACT LED (indicates data transmission via Ethernet)
[H]
Housing for the SD-card for e-mail attachment

storage (located on the reverse side of the board)
[I]
Interface to motherboard plug (located on the

reverse side of the board)
[J]
Screw locations
[A]
Ethernet port
[B]
Power supply LED
[C]
Collision LED (Network collision)
[D]
Connection speed LED @ 100Mbp
[E]
Collision LED (Network collision)
[F]
Packet reception via RS485 BUS LED
[G]
Packet reception via RS485 BUS LED
[H]
Interface to motherboard plug (located on the

reverse side of the board)
[I]
Screw locations
E
D
J
H
Figure 10 - The SmartLAN board
I
H
I
A
Figure 11 - The SmartLAN/SF board

Each SmartLAN or SmartLAN/SF board comes with:
3 anchor screws
3 spacers
Accessory devices
23
Installation manual
5.1.4
The SmartLoop/PSTN board
The SmartLoop/PSTN board allows the SmartLoop fire control panel to use the land line (PSTN). It
manages (and monitors) 2 lines and uses the most widely used reporting protocols (SIA, Contact ID, etc.).
It has an 8-slot audio memory for up to eight voice call messages. Completely managed by its on-board
microcontroller, it generates emergency calls in the event of a CPU fault, and also any alarm calls triggered
during the CPU fault.
[A]
L.I. Terminals for the internal phone-line connection. The signals

from the L.E. terminals (external landline) are diverted to these
terminals, thus allowing the connected telephone devices to use the
land line.
[B]
L.E. Terminals for the PSTN telephone connection
[C]
L.B. Terminals for the backup line (a secondary line to be used in the
event of "primary line-down" conditions)
[D]
Red LED for backup phone-line trouble signals
[E]
Red LED for main phone-line trouble
[F]
Green Activity LED (indicates data exchange between the

SmartLoop/PSTN board and the motherboard)
[G]
Yellow Line-engaged LED (goes On when the PSTN board hooks the
PSTN line)
[H]
Phone plug-in connector (for recording voice messages using a

normal phone)
[I]
Interface to motherboard plug (located on the reverse side of the

board)
[J]
Screw locations
J
D
H
J
I
Figure 12 - The SmartLoop/PSTN board

The SmartLoop/PSTN package includes:
4 anchor screws
4 spacers
5.1.5
The SmartLoop/INOUT board
The SmartLoop/INOUT board provides 6 outputs (CH1 - CH6). Each of these can be configured as:
Supervised output (NAC 1A max.)
Supervised input
Conventional detector line
Gas detector line
During the programming phase, you can program the events which will activate the outputs and the actions
generated by the inputs.
The SmartLoop/PSTN package includes:
4 anchor screws
4 spacers
Resistors and diodes
24
Accessory devices
Installation manual
D
E
[A]
Green Activity LED
[B]
Yellow Fault LED (fault on at least 1 of the 6

board channels)
[C]
Input/Output terminals
[D]
Interface to motherboard plug (located on

the reverse side of the board)
[E]
Screw locations
E
C
Figure 13 - The SmartLoop/PSTN board
5.2
SmartLoop/PRN Printer
The SmartLoop/PRN thermal printer module uses 82mm thermal roll paper and can be connected directly
to the motherboard (connector cable included). It provides a continuous real-time printout of events and/
or date to date enquiry printouts. It can also printout complete reports for each separate loop, containing
information related to the status of each detector/module (dust accumulation, loop communication quality,
real-time values, etc.).
A
B
D
F
C
E
Figure 14 - The SmartLoop/PRN module

[A]
Status LED and button to open the paper-roll housing
[B]
Paper roll button
[C]
Paper roll housing
[D]
Paper-roll housing fastener
[E]
Guide for anchor hook to the panel
[F]
Power supply terminals (24V DC) to be connected to the red and black wires of the cable (included)
[G]
Flat cable board to motherboard connector (included)
The SmartLoop/PRN module comes with:

A cable for the connection to the motherboard
Cable ties
2 hooks
Paper roll
Accessory devices
25
Installation manual
5.3
The SmartLetUSee/LCD and SmartLetUSee/LED Repeater panels
The SmartLoop fire control panel supports 14 SmartLetUSee/LCD remote Repeater panels. These remote
panels can be connected to the RS485 bus on the motherboard by means of a 4-pole cable. Repeater
panels replicate all the SmartLoop fire system data and allow authorized personnel to access and control
the system in accordance with access authorization (access requires code entry).
The repeater motherboard is located on the frontplate of the device, therefore, when you open the repeater
enclosure the reverse side of the motherboard is on view. The following is a description of the parts used
during the installation phase:
A
C
Figure 15 - The SmartLetUSee/LCD module

[A]
SmartLetUSee/LCD
Front of module
[B]
SmartLetUSee/LCD
Back of board
[C]
DIP switches
To set the repeater address
[D]
RS485 Terminals
From the bottom of the figure to the top +24V - + GND; for the connection
to the RS485 BUS
[E]
EOL Terminals
These terminal are for the setting jumper and, depending on the position of the
setting jumper, indicate the position of the repeater in the system.
[F]
SmartLetUSee/LED Terminals
Connector for the SmartLetUSee/LED module
You can connect a SmartLetUSee/LED module to each SmartLetUSee/LCD module by means of the
connection wire supplied with the module. The SmartLetUSee/LED provides 48 zone-status LEDs. The On/
Off of each LED can be configured individually during the programming phase.
Note:
The SmartLetUSee/LED module can be used only in combination with a SmartLetUSee/LCD module.
Figure 16 - The SmartLetUSee/LED module

26
Accessory devices
Installation manual
Chapter 6
Installation
Danger:
Installation of this fire control panel must be carried out in full respect of the local fire
codes, laws and bylaws in force, and in accordance with the instructions and guidelines
herein.
The cable glands must be rated UL94-V1 flame class (or higher)
6.1
Choosing the mounting location
This Fire control panel should be located in a place that is:

Dry
Far from electromagnetic interference (electrical equipment, heating units, air-conditioning units, radio
transmitters, etc.)
The mounting location must satisfy all the requirements of the respective Fire Code, laws and bylaws in
force.
6.2
Installation flow, guidelines and testing
1. Lay the cables

2. Connect all the loop and peripheral devices.
3. Install system peripherals
4. Mount the panel
5. Install accessory modules (if necessary)
6. Power up the system
7. Test the system (network, repeaters, ancillary and signaling devices).
Danger:
6.2.1
DO NOT apply mains power until all connections have been completed.
Wall mounting the panel
Work carefully through the following steps.

1. Mark the four wall plug holes on the wall and drill the holes.
Danger:
Care must be taken not to drill in the vicinity of electrical wiring, heating ducts and
plumbing.
2. Remove the knockout of the cable entry you intend to use (you can choose from knockouts on the sides
of the enclosure or use one of the cable entries on the back).
3. Fit a cable gland (not included) to the wire entry.
4. Using wall plugs, attach the enclosure securely to the wall.
5. Pull the cables through the cable entry.
6. Connect ant attachment boards to the motherboard.
7. Connect the SmartLoop/PRN module (if used) to the motherboard (paragraph 5.2 SmartLoop/PRN
Printer)
8. Complete the connections.
Installation
27
Installation manual
6.2.2
Connecting attachment boards
Figure 17 - Connecting attachment boards

1. Find the attachment board location on the motherboard (refer to Figure 7 - The motherboard
accessorized with attachment boards).
If you are installing a SmartLoop/2L board, insert un one end of the flat cable (included) into the
respective connector on the motherboard (paragraph 4.2 - [D]).
2. Remove the relative screws from the motherboard.
3. Screw the metal spacers into place (included).
4. Position the accessory board on the supports and check that the accessory board connector is properly
inserted.
5. Using the previously-removed screws, secure the attachment board in place.
6. If you are installing a SmartLoop/2L board, using the free end of the flat cable (included), connect the
accessory board to the motherboard.
6.3
Connecting the SmartLoop/PRN printer module
1. Unscrew the nuts from the screws which secure the printer-housing protection plate in place (paragraph
4.1 - [D]) then remove the plate.
2. Working from the front of the enclosure (door closed), insert the Printer into its location.
3. Holding the printer module firmly in place, open the door of the enclosure and position the hooks on the
guide (paragraph 5.2 - [E]) , ensure that the module is firmly positioned.
4. Connect the printer wire to the terminals on the reverse side of the module (paragraph 5.2 - [F] and
paragraph 5.2 - [G]) and to the motherboard via the respective connector (paragraph 4.2 - [M]).
5. Use the cable ties and plastic cable hooks (included in the SmartLoop/PRN kit) where necessary on the
reverse side of frontplate (above the motherboard), in order to secure the connection wires firmly in
place.
28
Installation
Installation manual
Chapter 7
Connections
7.1
Note to the Installer regarding wiring and connection compliancy
7.1.1
Two wire connection
For a system that is EN54 compliant, no more than 32 sensors can be connected when this type of wiring is
used.
7.1.2
Four wire connection
For a system that is EN54 compliant, an insulation module must be installed for each group of 32 detectors
(refer to Appendix A, Appendix B and Appendix C for information regarding the devices with built-in
isolators).
Fire code guidelines

Danger:
If you are using a 2 wire connection, no more than 32 detectors can be connected to the
loop.
If you are using a 4 wire connection, T junctions are prohibited, that is unless the maximum
number of devices that risk isolation during any type loop fault does not exceed 32.
If the system loop devices do not have built-in isolators, you must install an isolator for each
group of 32 detectors. Refer to Appendix A, Appendix B and Appendix C for further details.
All circuits should be wired using the local country Fire Code compliant method.
7.2
About the circuitry
The fire alarm system circuitry is critical to the safety and well being of the building occupants. It is
considered an essential communication path during evacuation or relocation of persons during a fire or
emergency situation. During such an event, it is critical for fire safety equipment such as fire alarm
signaling equipment to remain operational for a specified amount of time. Therefore, all circuits are to be
wired using the local country Fire Code compliant method.
7.2.1
Guidelines
The fire alarm system circuitry must not be commingled without proper separation, and must be kept
separate from all other wiring.
Junction boxes are required at splice points. All Junction boxes must be installed using the local country
Fire Code compliant method.
Any wires/cables inside the SmartLoop enclosure must be secured to the cable hooks on the back box by
means of plastic cable ties or similar fittings.
The mains power supply cable must enter the control panel enclosure through the appropriate cable
entry and must not cross other conductors. The mains power supply cable must be secured to the cable
hook on the back box by means of a plastic cable tie.
7.3
Loop Connections
The loops accommodate a vast array of fire system devices (detectors, manual callpoints, fire buttons,
Input and Output modules, etc.).
For a detailed description of the devices the loop accepts, refer to Appendix A, Appendix B and Appendix C.
Due to electrical incompatibility, different brand devices (i.e. devices using different protocols) cannot coexist on the same loop. However, the loops can be programmed separately in such way as to allow the
system to manage different brand devices on different loops.
Connections
29
Installation manual
Note:
Each loop output conductor must be fitted with a split ferrite core (included), as shown in the figure below.
Figure 18 - Attaching the split ferrite core to loop output cables
7.3.1
Loop terminals
LOOP1-O and LOOP2-O - loop output (paragraph 4.2 - [A4] and paragraph 4.2 - [A6])
Terminals + and : connect all loop devices in parallel to these terminals, in accordance with the
specific device instructions.
Earth terminal
Note:
: connect the shield of the STP cable (2 pole) to this terminal.
Always leave one end of the shield disconnected.
LOOP1-I and LOOP2-I - loop input (paragraph 4.2 - [A3] and paragraph 4.2 - [A5])
Terminals + e : connect the loop return loop wiring to these terminals.
These terminals allow the panel to check the loop integrity. In the event of a single interruption on the
circuit, the panel will communicate with the isolated trunk elements via these terminals.
Earth terminal
Note:
7.3.2
: connect the shield of the STP cable (2 pole) to this terminal.
Always leave one end of the shield disconnected.
Loop limitations
Use suitably sectioned shielded twisted cable for the loop wiring. Connect the shield to earth using the
earth terminals to one end of the loop only.
In order to allow the loop to function properly, you must section the device connection cable in such way
that any voltage drop along does not exceed 8 V. The following table shows the minimum dimensions for
the loop wiring with regard the distance between the loop output terminals and the most distant device:
30
up to 500 m
minimum 1 mm2
up to 1000 m
minimum 1.5 mm2
up to 1500 m
minimum 2 mm2
up to 2000 m
minimum 2.5 mm2
Connections
Installation manual
7.3.3
Connecting devices to the Loop
Il loop wiring can be completed with 2 wires (open loop) or 4 wires (closed loop) using 2 pole STP.
Figure 19 - 2 wire connection
If you are using a 4 wire connection, connect the STP cable shield to one end of the loop and leave the
other end disconnected.
Figure 20 - 4 wire connection
Connections
31
Installation manual
7.4
NAC Outputs (Notification Application Circuit)
7.4.1
Alarm NAC
The ALARM NAC (paragraph 4.2 - [A1]) is a fuse-protected, supervised-silenceable output which is to be
connected to the alarm signalling devices.
This output will activate when FIRE ALARM conditions are detected. In the event of activation, the output
will supply a 24V current in accordance with the polarity indicated on the terminals.
During the STANDBY phase a low supervisory current with reverse polarity (with respect to the silkscreened indications on the motherboard) circulates on the line. The diodes (connected in series to the
loads) will direct the current to the EOL resistor which must be connected in parallel to the last device
(refer to Figure 21 - Wiring diagram of the ALARM NAC, FAULT OUT, NAC1, NAC2 and NAC3 outputs).
7.4.2
Fault output
The FAULT OUT (paragraph 4.2 - [Z]) is a fuse-protected, supervised-silenceable output which is to be
connected to the fault signalling devices (LEDS, etc.).
This output will activate when fault conditions are detected. In the event of activation, the output will
supply a 24V current in accordance with the polarity indicated on the terminals.
During the standby phase, a low supervisory current with reverse polarity (with respect to the silkscreened indications on the motherboard) circulates on the line. The diodes (connected in series to the
7.4.3
NAC1, NAC2 and NAC3 outputs
The NAC1, NAC2 and NAC3 outputs (paragraph 4.2 - [A2]) are programmable generic outputs, protected
by a 1A fuse. They can be connected to various types of signaling and control devices (pressure valves, fire
doors, etc.).
These outputs will activate in accordance with programming. In the event of activation, the output will
supply a 24V current in accordance with the polarity indicated on the terminals.
During the standby phase, a low supervisory current with reverse polarity (with respect to the silkscreened indications on the motherboard) circulates on the line. The diodes (connected in series to the
VIOLET
YELLOW
ORANGE
GOLD
Figure 21 - Wiring diagram of the ALARM NAC, FAULT OUT, NAC1, NAC2 and NAC3 outputs
7.5
PL Terminal
These terminals can be used to provide Shutdown signaling.

The Normally Open PL terminal (paragraph 4.2 - [T]) closes to GND (ground) in the event of control panel
shutdown (mains and battery power failure).l
32
Connections
Installation manual
7.6
AUX output
The AUX output (paragraph 4.2 - [U]) provides a 24 V (max 1.3 A) power supply output for external loads
(ancillary devices).
This output is short-circuit protected by a resettable fuse. In the event of a short-circuit, the panel will
signal an AUX output fault.
7.7
AUX-R output
The AUX-R output (paragraph 4.2 - [V]) supplies a 24 V (max. 1.3 A) power supply (which is removed
temporarily during control panel reset) to external loads (ancillary devices) that must switch off in order to
reset (e.g. beam detectors).
This output is short-circuit protected by a resettable fuse. In the event of short-circuit, the panel will signal
an AUX-R output fault.
7.8
Alarm relay
The ALARM RELAY provides (paragraph 4.2 - [X]) a voltage-free contact which can switch loads of up to
5A (max. 30 V). This relay toggles its status in the event of panel fault.
Attention:
7.9
In order to validate the IMQ-SECURITY SYSTEMS certification, this output should not be used
as a type C and/or E and/or J and/or G output (EN 54-1), therefore, it must not be used to
command fire alarm devices and/or fire alarm transmission devices.
Fault relay
The FAULT RELAY provides (paragraph 4.2 - [Y]) a voltage-free contact which can switch loads of up to
5A (max. 30 V). This relay toggles its status in the event of panel fault.
Attention:
7.10
In order to validate the IMQ-SECURITY SYSTEMS certification, this output should not be used as a
type J output (EN 54-1), therefore, it must not be used to command Fault transmission devices.
Connecting devices to the RS485 BUS
The RS485 BUS accepts up to 14 repeater panels, 4 power stations and 4 SmartLine-EXT conventional
extinction stations.
POWER
STATIONS
EXTINCTION
STATIONS
SmartLevel
SmartLine-EXT
REPEATERS
SmartLetUSee/LCD
Figure 22 - RS485 BUS connections

1. Use 4-pole shielded twisted cable for all connections.
2. Complete the RS485 BUS connections in parallel. Do not connect any wires to +24 terminal of the
RS485 BUS of the SmartLine-EXT extinction stations.
3. Insert the jumper in the EOL position on the last device, whether it is a repeater or power station (this
operation must not be carried out on extinction panels).
Connections
33
Installation manual
The maximum wire length of the RS485 BUS is 1000 meters.
7.10.1 Setting the devices connected to the RS485 BUS

1. Assign an address to each device. The address identifies the device distinctly on the RS485 BUS. When assigning
addresses to repeaters, use the DIP switch (paragraph 5.3 - [C]). For the description of the addressing
procedure of SmartLevel and SmartLine-EXT stations, refer to the respective programming manuals.
Address
DIP
switch
position
DIP
switch
position
Attention:
ON
ON
ON
ON
ON
ON
ON
Address
10
11
12
13
14
ON
ON
ON
ON
ON
ON
ON
All other DIP switch configurations are NOT allowed.
2. Ensure that the EOL jumper (paragraph 5.3 - [E]) is in the EOL position (End Of Line) on the last repeater
or power station on the line but not on other devices.
Jumper position for the last

repeater on the line (EOL)
Jumper position for the centrally

positioned repeater
Figure 23 - SmartLetUSee/LCD-Lite board - jumper position
Jumper position for the last

power station on the line (EOL)
Jumper position for the

centrally positioned power
Figure 24 - SmartLevel board - jumper position
34
Connections
Installation manual
7.11
Connecting the SmartLoop/NET module
Use either 4-pole shielded twisted cable for the connections or Cat 5 STP cable for Ethernet connections. The
latter will allow you to wire the data communication ring and the emergency alarm ring.
Figure 25 - Connecting the SmartLoop/NET module

Danger:
In order to allow the ring to operate properly, the PORT-B and ALARM-B terminals must be
connected to the successive PORT-A and ALARM-A terminals.
The control panel uses an RS485 BUS for the HorNet ring node to node communications. The RS485 BUS
communicates at speeds of up to 57600 baud over distances up to 2000 metres between two nodes. The
SmartLoop/NET ports are opto-isolated, as without isolation the connection to the data acquisition
hardware to the target carries the potential for creating ground loops which will cause excessive noise in
the signal.
7.12
Connecting the SmartLoop/INOUT Board
Each of the terminals on the SmartLoop/INOUT board can be configured in one of the following ways:
A
VIOLET
YELLOW
ORANGE
GOLD
WHITE
ORANGE
RED
Conventional
smoke
detector
Connections
Conventional
smoke
detector
GOLD
35
Installation manual
Gas
detector
4-20mA
BLACK
BROWN
RED
GOLD
SmartLoop
control panel
D
VIOLET
YELLOW
GREEN
BROWN
ORANGE
GOLD
ORANGE
GOLD
Figure 26 - Connecting the SmartLoop/INOUT module

[A]
Supervised NAC Output
[B]
Conventional Zone
[C]
Gas Zone
[D]
Supervised Input
7.13
Lines configured as Gas Zone 4-20mA will generate an early warning signal if the value of the
detector output exceeds 12mA, and an alarm signal if the value of the detector output exceeds
16mA.
In order to implement the early warning signal, it must be enabled (during the programming
phase) on both the control panel and the zone the line belongs. The early warning signal will stop
automatically, if a gas detector exceeds the 12mA early warning threshold then returns below this
value without reaching the alarm threshold.
Connecting to a PC
The panel can be connected:

permanently to a PC equipped with monitoring software;
temporarily to a PC during system configuration sessions (for uploading/downloading).
The panel can be connected via:
RS232 port
USB port
Ethernet port (if the system is equipped with a SmartLinkLAN board)
Note:
Use of one of these ports automatically excludes use of the others.

The communication ports are opto-isolated in order to allow permanent connection to a PC or printer.
If the connection is through the USB port, the system may ask for the installation driver when the USB
cable (LINKUSBAB accessory item) is first inserted. The driver is included in the SmartLeague software
programme which, once installed, can be found in the following folder:
C:\Program files\Inim\SmartLeague\Drivers\
36
Connections
Installation manual
7.14
Connecting a SmartLAN (or SmartLAN/SF) equipped control panel to a PC
In this case, the RS232 and USB port will not be available for use. Therefore, the PC must be connected
directly to the Ethernet port of the SmartLAN board or through a network switch by means of an inverted
patch-cord.
The default IP address is 192.168.1.92
Consequently the integrated Ethernet board of the PC must be configured with an IP of the same class (e.g.
192.168.1.46). Once the configuration phase is complete, you will be able to open your browser and enter
the SmartLAN board address:
http://192.168.1.92
7.15
Connecting a serial printer
1. Connect the serial printer to the RS232 port.

2. From the panel, access the main menu and select Printer Settings
3. Enable the printer to communicate with the panel
Note:
7.16
If you intend disconnecting the serial printer from the RS232 port in order to connect a PC, it will be
necessary to DISABLE the serial printer before doing so. If you do not DISABLE the serial printer, the PC
will be unable to communicate with the panel.
Batteries
The panel enclosure provides housing for two 12 V/17 Ah internal batteries.
Use YUASA batteries, model NP 17 -12 FR or similar with UL94-V2 flame class (or higher).
Once powered up, the panel will recharge and monitor the batteries automatically, as follows.
7.16.1 Efficiency testing

The panel checks the efficiency of the batteries at 60 second intervals, by simulating load current demand
(as required during mains black-out). If the battery results inefficient, the condition will be signalled on the
respective fault LED on the frontplate and also on the display.
7.16.2 Voltage testing

The panel continuously monitors the battery voltage. If the voltage drops below the 22.8 V, the panel will
signal the event on the respective fault LED and on the display. The event will end when the voltage
restores to over 24.6 V.
7.16.3 Deep discharge monitoring

If the battery voltage drops below 18 V, the panel will disconnect them in order to avoid battery damage. If
this occurs, the PL terminal will close to ground thus generating a Shutdown signal.
7.16.4 Connecting the batteries

1. Locate the batteries inside the panel enclosure.
2. Using the battery wire (Figure 27 - [A]), connect the batteries together.
3. Using the battery terminal eyelet wires (included), connect the battery (Figure 27 - [B]).
Attention:
Ensure that connector polarity is correct.
4. Connect the battery wire connector (Figure 27 - [C]) to the control panel (paragraph 4.2 - [R]).
Attention:
Connections
Ensure that connector polarity is correct.
37
Installation manual
Figure 27 - Connecting the batteries
7.17
Connecting the thermal probe
Attention:
In order to validate the IMQ-SECURITY SYSTEMS certification and comply with EN 54-4
requirements, installation of a thermal probe is essential.
This panel has an on-board connector (paragraph 4.2 - [O]) for a thermal probe (accessory item). The
ProbeTH thermal probe regulates the battery-charge system by interacting with the battery temperature,
this operating method avoids battery damage.
1. Disconnect the batteries (if already connected).
2. Connect the thermal probe (Figure 27 - [D]) to the connecter (paragraph 4.2 - [O]) on the
motherboard.
3. Using a strip of strongly-adhesive insulating tape (Figure 27 - [E]), attach the Thermal probe to one of
the batteries, in such way as to a provide optimized heat-transfer measurements.
4. Using a thermometer, measure the probe temperature.
5. Using the graph Figure 28 - Voltage charge in relation to the battery temperature find the optimized
heat-transfer measurement for the charge.
6. Using a voltmeter, measure the voltage on the AUX terminals (paragraph 4.2 - [U]).
7. Adjust the trimmer (Figure 29 - [B]) on the switching power-supply (Figure 29 - [A]) to the value
indicated on the graph.
Volt
29
28,5
28
27,5
27
26,5
26
25,5
0
10
15
20
25
30
35
40
45
50
Figure 28 - Voltage charge in relation to the battery temperature

38
Connections
Installation manual
7.18
Connecting the mains power source
The power system of the SmartLoop control panel is EN54-4 compliant.
D
C
A
C
Figure 29 - Switching power-supply and mains connection
Danger:
DO NOT power up the system with a non-compliant voltage (Figure 29 - [B]).
1. Connect the mains to the terminals on the switching power-supply module.

For a safety standards compliant system, the Line must be connected to terminal L, the Neutral
conductor to terminal N and Earth to terminal (Figure 29 - [C]).
This panel must be connected to a separate line on the Electrical Switchboard (Mains power supply).
The line must be protected by a sectioning device which complies with local safety regulations, fire
codes, laws and bylaws in force.
Danger:
The protective earthing system must be compliant with the local safety regulations, fire
codes, laws and bylaws in force.
Note:
As a further safety measure, the electrical system of the building must be protected against
overload and short-circuit.
Primary power source: 230 Vac (-15%/+ 10%) 50/60 Hz.

Maximum current draw: 0.9 Aac
2. After connecting the conductors to the power module terminals (Figure 29 - [E]), using a cable tie,
bunch the wires together and attach them firmly to one of the cable hooks on the backbox.
The mains supply conductors must not cross other conductors.
Note:
The connection wires (to the electrical mains, and also any other wires inside the enclosure) must be
secured by means of plastic cable ties or similar fittings. Use cable with double isolation for the connection
to the electrical mains. Ensure that the switching power supply is properly earthed and, if you are installing
a SmartLoop/PSTN, ensure that the metal supports are tightly screwed in place, in accordance with the
instructions in this manual.
3. Insert and connect the two 12 V/17 Ah internal batteries (refer to paragraph 7.16.4 Connecting the
batteries).
Note:
Connections
A protective earth connection ensures that all exposed conductive surfaces are at the same electrical
potential as the surface of the Earth, in order to avoid the risk of electrical shock if a person touches a
device in which an insulation fault has occurred. In the event of an insulation fault, a protective earth
connection will generate a high fault current which in turn will trigger an over current protection device
(fuse) and disconnect the power supply.
39
Installation manual
Chapter 8
Powering up the system

Attention:
8.1
When you think you have the system completely wired, double check the integrity of the
wiring and ensure that the earth connection has been completed properly before powering
up.
Testing wiring integrity
Work carefully through the following steps, use a multimeter or similar tool for the electrical
measurements.
1. Check there is no electric current flow between the cables and earthing system.
For accurate measurement, remove the extractable terminal boards from the motherboard.
2. Check there is no electric current flow between the cable shields and earthing system.
For accurate measurement, disconnect the shields from the respective terminals by removing the
extractable terminal boards.
3. Check the wiring integrity of each NAC output.
For accurate measurement, remove the respective extractable terminal boards from the motherboard
and measure the cable resistance. Test both polarities, at least one of them must have the same
resistance as the EOL resistance.
4. Check all cables are adequately separated, bunched (by means of cable ties) and attached firmly to the
cable hooks on the back of the enclosure.
5. Check the proper polarity of the primary power supply connections (230 Vac) and ensure the wire is
attached firmly (by means of a cable tie) to a cable hook on the back of the enclosure.
6. Ensure that the connected repeater panel DIP microswitches have been properly set (refer to paragraph
7.10.1 Setting the devices connected to the RS485 BUS).
7. Ensure that the EOL jumper [figure 42] is in the EOL position on the last repeater panel only.
8. If several panels are connected in a token ring network, check the integrity of the ring, as follows:
9. extract the network terminal boards from the SmartLoop/NET board (refer to paragraph 5.1.2 The
SmartLoop/NET board) of one of the panels and check the continuity of wiring in the D+ circuit
(between the D+ poles of ports A and B), and in the D- circuit (between the D- poles of ports A and B).
8.2
First power up
1. Insert the jumper for programming-data storage (paragraph 4.2 - [G]); data storage is guaranteed by
the 2032 lithium battery.
2. Connect the two 17Ah batteries as described in paragraph 7.16.4 Connecting the batteries.
3. The panel will take several seconds to stabilize and the screen will show Resetting.
4.
The CPU FAULT LED on the frontplate will blink to indicate board activation.
5. If the connection with mains power supply is not detected within 2 minutes, the control panel will signal
a fault. Power the panel from the mains.
6. If at this point the panel signals other faults, check the wiring integrity and clear all faults before
continuing (refer to Chapter 10 - Troubleshooting).
40
Installation manual
7. Once all fault conditions have been cleared, turn the key in the keyswitch to access Level 2 (refer to
paragraph 2.4 Operator classification - Access Levels) then press RESET. The display will show:
SmartLoop In Service
No Alarm
No Fault
11/11/11 06:23 Fri
Figure 30 - Message on display on first startup
8. Press the TEST button to check the integrity of the LEDs.
41
Installation manual
Chapter 9
Maintenance
The following operations must be carried out regularly.
1. Using a damp lint-free cloth, remove any dust that may have gathered on the control panel enclosure.
Attention:
Do not use any kind of cleaning product or solvent!
2. Push the TEST button to check the proper operating capability of the LEDs and buzzer.
3. Check the battery efficiency and change them if necessary.
4. Check the integrity of all wires and connections.
5. Ensure that there are no insects inside the control panel.
6. Carry out maintenance on the smoke detectors (clean the outside and the detection chamber).
Note:
42
Points 1 and 2 can be carried out by authorized persons, whereas all other points must be carried out by
qualified technicians.
Maintenance
Installation manual
Chapter 10
Troubleshooting
10.1
Fault NAC, alarm or fault output trouble
Using a multimeter or similar tool, check the voltage on the terminals. During normal operating conditions
(standby status), the measurement should be around 15 V with reverse polarity with regard the silkscreened indications on the terminal board.
If the measurement is around 24 V with reverse polarity with regard the silk-screened indications on the
terminal board, then either the circuit does not end on the EOL resistance or there is an interruption on
the cable.
Check the integrity of the device connections and the EOL resistance on the last device.
Check the cable continuity.
If the measurement is around 0 V the cable is shorted.
Check the device connections and the various cable sections.
10.2
LOOP fault
If the Shorted Loop OUTwarning appears on the panel display, a short-circuit in the loop across the
Loop-O terminals and the first isolator has been detected.
Check the integrity of the connection wiring and the integrity cable in the first section of the loop.
If the Shorted Loop-I warning appears on the panel display (for loops with 4-wire circuitry only), a
short-circuit in the loop has been detected in the section across the Loop-I terminals and their nearest
isolator.
Check the integrity of the connection wiring and the integrity of the cable in the last section of the loop.
If the Shorted OPENwarning appears on the panel display (for loops with 4-wire circuitry only), the
Loop continuity across the Loop-O and Loop-I terminals is interrupted. This may be caused by:
- An open isolator in the loop
Check all the isolators in the loop. At least one of the isolator LEDs will signal Isolated status. Once
you have traced the isolator in question, check the successive isolator on the loop which, very probably,
will also be open.
Check the integrity of the wiring in the section between the two isolators.
- Cable Interruption
Disconnect the Loop-I terminals of the panel.
Check the condition of the loop-device LEDs (blinking) until you find the point where the loop is interrupted.
Once the last device in proper working order has been identified, check the integrity of the wiring and
the cable in the successive section.
- Missing loop devices (the panel is unable to find some of the connected loop devices)
Search the loop for the missing devices. Once the missing devices have been identified, check the
integrity of the wiring and the address of each missing device.
- Duplicated address (an address has been assigned to more than one device)
Switch On the LED of the devices that signal duplicated address.
Search the loop for the devices concerned. Once the devices have been identified, check the address of
each device and rectify the error.
Loop status LEDs
- Check that the blinking Loop transmission LED (red) corresponds to the respective loop settings. If the
LED does not correspond, check the loop parameters.
- The green LED of each loop will blink each time an interrogated device responds. If this LED is On solid,
it means the device response is masked by an anomalous current flow through the conductive path
between the two poles of the loop.
Troubleshooting
43
Installation manual
Attention:
10.3
Ensure that only the system devices are connected to the loop.
Fault on devices connected to the RS485 BUS
If the display shows Repeater Lost, Power Stat. Lost, Ext. Stat. Lost , the panel is
unable to find any devices connected to the BUS.
Check that the device addresses have been assigned correctly (refer to paragraph 7.10.1 Setting the
devices connected to the RS485 BUS).
Check the integrity of the wiring and the connection polarity.
Check that the EOL jumper is in the EOL position only on the last repeater or power station connected to
the BUS.
Using a multimeter or similar tool for the electrical measurements:
- Measure the voltage across the +24 V and GND terminals of the RS485 BUS. If the voltage is below 20
V, the resettable protection fuse is open, therefore, the current draw of the devices connected to the
BUS is excessive.
- Disconnect the devices connected to the BUS one at a time until you find the cause.
10.4
Battery Fault
If the Battery lost message is shown, the batteries are either disconnected or have failed the battery
efficiently test.
Allow them to recharge for several hours. If the trouble persists, disconnect the batteries from the panel
and, using a multimeter or similar tool, measure them separately.
If only one of the batteries is below 12.5 V: replace the battery concerned and allow it to recharge for
several hours until fully charged.
If both batteries are below 12.5 V .13 V: replace both batteries and allow them to recharge for several
hours until fully charged.
If the battery is equipped with a thermal probe, check that the voltage value corresponds to the value
calculated with the assistance of the graph (paragraph 7.16.4 Connecting the batteries). If there is a
discrepancy in the value, correct it by means of the trimmer on the power supply module.
If the Low Battery message is shown, the primary power source (230 Vac mains power) is
disconnected. This condition must be cleared before the batteries get too low and are unable to power to
the system.
10.5
SmartLoopNET Fault
10.5.1 Error in the token ring network configuration
Access to Network Denied

Network board NOT found
or address already occupied or Loop Open
Figure 31 - Access Denied message

This message appears when:
The SmartLoop/NET board is not operating properly.
Check that the board is inserted properly.
Relaunch the auto-configuration phase.
Ensure that the blue LED (paragraph 5.1 - [E]) remains On during this phase, and that the activity LEDs
of nodes A and B (paragraph 5.1 - [F] and paragraph 5.1 - [G]) flicker to indicate communication
attempts on both sections.
If all the LEDs are Off, the board may be damaged and it may be necessary to replace it.
44
Troubleshooting
Installation manual
An address has been duplicated, that is, assigned to more than one panel.
Access the main menu from the panel. Select Programming, Configuration, View configuration,
Network
Check the address of each panel in the token-ring network and rectify the error.
Network circuit open
The token-ring network cabling must be closed properly otherwise the system will be unable to configure
properly.
Check the integrity of the ring cabling, as follows:
- Restore all the panels in the token-ring network to address O.
- Disconnect the network terminals of the SmartLoop/NET board of one of the panels, then check the
continuity of the wiring between the D+ poles of the A and B ports and between the D- poles of the
A and B ports and the two - poles (refer to paragraph 5.1.2 The SmartLoop/NET board).
10.5.2 Fault on ALARM-A/B terminals

Wiring fault in the emergency alarm ring circuit.
Check the integrity of the circuit wiring of the panel that generated the event.
Using a multimeter or similar tool, measure the voltage over terminals ALARM-A + and . Under
normal operating conditions the value should be approximately 2.5 V.
- If the value is nearer to 5 V, the connection with terminals ALARM-B + and - of the adjacent control
panel is interrupted.
- If the voltage is nearer to 0 V, there may be a short-circuit between the two poles that connect the
ALARM-A + and - terminals of the board concerned with the ALARM-B + and - terminals of the
antecedent board.
Check the integrity of the connection.
Note:
If the emergency alarm loop is not used, it must be disabled via software, otherwise it will signal a
persistent fault condition.
Troubleshooting
45
Installation manual
Appendix A
Enea devices
All devices in INIM's new Enea series of addressable-analogue detection
devices are LPCB certified and carry the CE mark according to CPD.
Each device is equipped with a short-circuit isolator which, in the event
of short-circuit between two control-panel (loop) connection wires, is capable of interrupting the negative
wire and isolating the wire section concerned. Up to 240 devices can be connected. Each device is identified
by a factory-assigned serial number which allows automatic addressing.
INIM's Enea series provides three analogue detector models:
Optical chamber with sealed upper-part and 500 micron hole-diameter mesh insect screen
Three-colour LED - Red for alarm, Green flash for standby and for identification from the control panel;
Yellow for fault status
Supervised remote output configurable from the control panel
Automatic recognition of remote signaller connection
Drift compensation for sensor drift caused by dust in the chamber
Sensitivity selection for smoke and heat thresholds
Operating mode selection (for ED300 version) - Only smoke; Only heat
AND mode, OR mode, PLUS mode
Complete diagnostics - provides contamination level and real-time values
Memory of the smoke and temperature levels measured in the five-minute period prior to the last alarm
detected
Bypass plate on base guarantees continuity in the event of removal of the detector from the line
For further details regarding the precise features and technical specification of each device, refer to the
respective instructions booklet.
Type
Detectors
Bases
Modules
Manual
callpoint
LED
46
Model
Description
ED100
Optical smoke detector
ED200
Heat detector
ED300
Heat and smoke detector
EB0010
Mounting base
EB0020
Relay base
ESB010
Base sounder (to be installed under an EB0010 base)
ESB020
Base sounder and beacon (to be installed under an EB0010 base)
EM312SR
Input/Output module
EM110
Input module
EM311
Micromodule
EM344S
Conventional zone interface module with 4 inputs + 4 outputs
EC0010
Manual callpoint
EC0010E
Weatherproof manual callpoint for outdoor installation (IP67)
FI100
Addressable remote alarm repeater
Enea devices
Installation manual
Sounder
Driver
A.1
ES0010RE
Loop-powered addressable sounder in red enclosure
ES0020RE
Loop-powered addressable sounderflasher in red enclosure
ES0010BE
Loop-powered addressable sounder in white enclosure
ES0020BE
Loop-powered addressable sounderflasher in white enclosure
ES0020
Loop powered addressable fire sign
EITK1000
Kit for the configuration, maintenance and diagnostics of systems

using IRIS and ENEA series devices
EITK-DRV
Driver for zones with IRIS series devices or loops with ENEA
series devices
EITK-BASE
Base for IRIS and ENEA series devices
EITK-PWSP
Power supply for the EITK-DRV driver
Configuring Enea series devices
The distinct serial number of each detector is shown on the device information label. Manual addressing is
unnecessary as the addressing phase is automatic. To address devices, connect them to the loop and work
through the following steps.
Figure 32 - The reverse side of Enea detectors

The serial number is shown on the information label [A] and on two smaller removable labels [B]. When
installing the devices, it is strongly advises to remove the small labels and place one on the system layout
and the other on the mounting base. This will facilitate device tracing and re-location operations.
Note:
Each loop supports up to 240 devices.
A.1.1 Re-addressing devices

After connecting the devices to the loop, you must then configure the loop.
The addressing phase allows the system to determine the serial number of each device connected to the
loop and assign a logic address (a number between 1 and 240). The system will use this number to identify
the point during all the system programming operations.
From panel: <key>, Programming, <code>, Configuration, Modify Configuration, Manual
Configuration, Loop - select the loop - Loop parameters - set the protocol type as
INIM and the wiring method as 4 Wire, , Esc, Esc, Esc, Auto Enroll, Loop, place
the cursor arrow on the desired loop (column 1 to 8) on the RE-ADDRESS ALL. line.
Using the S key, enter the "+" sign (which will appear on both lines automatically), ,
Enea devices
47
Installation manual
Loop N.
ENROLL DEVICES
RE-ADDRESS ALL.
1 2 3 4 5 6 7 8
: . . . . . . . .
: . . . . . . . .
Once this operation is complete (this operation may take several minutes), a summary screen showing the
total number of devices found will be shown. Ensure that the number of devices found corresponds to the
number of devices actually installed.
Via PC: select the loop > Parameter Tab to select the type of protocol and wiring method, select the icon
and select Re-address loop.
Once this operation is complete (which may take several minutes), the software programme will design a
layout of the loop wiring showing all the connected devices.
A.2
Reading the loop operation
This operation allows the system to read the serial number of each device on the loop and acquire its logic
address (from 1 to 240), assigned during a previous addressing operation.
Note:
This operation can be carried out only when dealing with a previously addressed loop (addressed via a
control panel or EITK-DRV loop driver).
From panel: <key>, Programming, <code>, Configuration, Modify Configuration, Manual

Configuration, Loop, select the loop, Loop parameters, set the protocol type as INIM
and the wiring method as 4 Wire, , Esc, Esc, Esc, Auto Enroll, Loop, place the
cursor arrow on the desired loop (column 1 to 8) on the ENROLL DEVICES line. Using
the S key, enter the "+" sign (which will appear on both lines automatically), ,
Once this operation is complete, a summary screen showing the total number of devices found will be
shown. Ensure that the number of devices found corresponds to the number of devices actually installed.
Via software programme: select the loop > Parameter Tab to select the type of protocol and wiring
method, select the icon
and select Read loop.
Once this operation is complete (which may take several minutes), the software programme will design a
layout of the loop wiring showing all the connected devices.
A.3
Updating the loop operation
This operation must be carried out each time a device is replaced or added to a previously configured loop.
After replacing or adding devices to the loop, work through the following operations.
From panel:
Adding/Replacing a device:
<key>,
Programming,
<code>, Configuration,
Modify
Configuration, Manual Configuration, Loop, select the loop, Add/Modify Point, select
the point and enter the serial number of the new or replacement device.
Removing a device: <key>, Programming, <code>, Configuration, Modify Configuration, Manual
Configuration, Loop, select the loop, Remove point, select the point and press to
confirm.
Via software application: select the loop from the tree structure, then select the icon
Update Loop option.
and then the
Once this operation is complete (which may take several minutes), the software programme will show a
double layout which will allow you to compare the previously-saved loop configuration with the new one.
The parts with changes will be highlighted.
In order to continue, you must accept all the highlighted changes by double-clicking on the icons which are not
green (or press the Accept ALL button), then press CONTINUE. A new addressing phase (which may take
several minutes) will transfer the new configuration to the control panel.
48
Enea devices
Installation manual
Appendix B
Argus Devices
Note:
The ARGUS devices accepted by this control panel do not have IMQ-SECURITY SYSTEMS certification, refer
to the instructions leaflet provided with each device.
All Argus Vega devices have built-in loop isolators. Therefore, isolators are not required. A short-circuit on
the loop will not provoke loss of any device.
Each detector is equipped with a 3-colour LED: green (periodic blinking) indicates the detector is working
properly (if enabled). Yellow indicates that the detector is not operating properly (fault) or has an open
isolator, whereas red indicates alarm status.
Detectors are equipped with test LEDs: if you hold a magnet near the detector base (near to the two
notches) the detector should generate an alarm signal.
B.1
Devices
Model
Name
Description
V100
Analogue optical detector
V200
Analogue Multicriteria detector
Optical smoke&heat detector
V350
Analogue temperature detector
Heat detector (a)
VCP100
Intelligent resettable callpoint
Callpoint with resettable mechanism
VWCP100
Weatherproof intelligent resettable callpoint
Callpoint with resettable mechanism for outdoor installation
VMI100
Input module
Module with 1 supervised input
VMMI100
Input Minimodule
Reduced-size module with 1 supervised input
VMDI100
DIN rail input module
DIN rail module with 1 supervised input
VUMI100
Input Micromodule
Reduced-size module with 1 supervised input
VMC100
Output Module
Module with 1 Supervised Output
VMMC100
Output Mini Module
Reduced-size module with 1 supervised output
VMDC100
DIN rail output module
DIN rail module with 1 supervised output
VUMC100
Output Micromodule
Reduced-size module with 1 supervised output
VMC120
Output Module Form C
Module with 1 voltage-free output (non-supervised)
VMMC120
Output Mini Module Form C
Reduced-size module with 1 voltage-free output (non-supervised)
VMDC120
DIN rail output module Form C
DIN rail module with 1 voltage free relay (non-supervised)
VUMC140
Output Micromodule Form C
Reduced-size module with 1 voltage-free output (non-supervised)
VMIC100
Input/Output Module
Module with 1 supervised input + 1 supervised output
VMMIC100
Input/Output Mini Module
Reduced-size module with 1 supervised input + 1 supervised output
VMDIC100
DIN rail Input/Output module
DIN rail module with 1 supervised input + 1 supervised output
VMIC120
Input/Output Module Form C
Module with 1 supervised input + 1 non-supervised output (voltagefree contact)
VMMIC120
Input/Output Mini Module Form C
Reduced-size module with 1 supervised input + 1 non-supervised

output (voltage-free contact)
VMDIC120
DIN rail Input/Output module Form C
DIN rail module with 1 supervised input + 1 non-supervised output

(voltage-free contact)
Argus Devices
49
Installation manual
VMCZ100
Conventional-line interface module
Interfaces conventional devices to the loop
VMIC404
Module with 4 inputs + 4 outputs
Module with 4 supervised inputs + 4 outputs (dry contact)
VLS100
Intelligent Wall Sounder
Loop-powered sounder (wall mount)
VWLS100
Weatherproof Intelligent Wall Sounder
Loop-powered sounder for outdoor installation
VLS100-AV
Intelligent Wall Sounderflasher
Loop-powered sounderflasher (wall mount)
VWLS100-AV
Weatherproof intelligent Wall Sounderflasher
Loop-powered sounder for outdoor installation (wall mount)
VLBE100
Intelligent Flasher
Loop-powered beacon
VTAO10
Sounderflasher fire sign
Visual/Audible fire sign with input/output module
VTAOA10
Self-powered Sounderflasher Fire Sign
Self-powered visual/audible fire sign with input/output module
VFI100
Intelligent Remote Indicator
Remote addressable alarm repeater
VPU100
Programmer
Allows fast addressing of Argus series devices
a. Configured as Rate-of-rise detector at default (alarm is triggered by rapid rise in temperature or when the temperature
exceeds the 54C alarm threshold). To configure as High temperature detector (Rate-of-rise feature bypassed and fixed
temperature set at 70C) use the VPU100 programmer. The panel will recognize the configuration criteria automatically.
B.2
Device Bases
Model
Name
Description
VB100
Base
Standard base for VEGA detectors
VDBS100
Deep Base
Allows connection to wall-mount cable runs
BLR100
Relay Base
Relay activated by the detector R output attached to the base
VBS100
Base with sounder
Activated by the detector R output attached to the base
VBLS100
Base with addressable sounder
This device occupies a loop address
B.3
Wireless devices
Model
Name
VW2W
Wireless Translator
SGWE
Wireless Expansion
SG100
Wireless Analogue Optical Smoke Detector
SG200
Wireless Analogue Optical Smoke/Heat Detector
SG350
Wireless Temperature Detector
SGRBS100
Wireless base sounder
SGRBS100-AV
Wireless base sounder with beacon
SGMI100
Wireless input module
SGMC100
Wireless output module
SGMCB100
Wireless module with 2 outputs
SGCP100
Wireless callpoint
SGRS100
Wireless sounder
SGVA100
Wireless voice announcer
SGFI100
Wireless addressable remote alarm repeater
Description
Connected to Loop, 32-device interface (Sagittarius series SG) wireless to panel
The control panel sees the 32 devices as loop-connected
devices with different addresses
(a)
a. Configured as Rate-of-rise detector at default (alarm is triggered by rapid rise in temperature or when the temperature
exceeds the 54C alarm threshold). To configure as High temperature detector ( Rate-of-rise feature bypassed and fixed
temperature set at 70C) use the VPU100 programmer. The panel will recognize the configuration criteria automatically.
50
Argus Devices
Installation manual
B.4
Device Consumption
Device
B.5
in stand-by
in alarm
Detectors
90 PA
6 mA
Modules
120 PA
6 mA
Configuring Argus devices
Every ARGUS device requires an address to identify it in the loop. You can address ARGUS devices by
either using a VPU (Vega Programming Unit) or by means of the Auto-addressing option.
B.5.1 Auto-addressing from panel

At the SmartLoop panel keypad:
1. Press any key to access the Main menu.
2. Select Programming, <code>, Configuration, Modify Configuration, Manual Configuration,
Loop
3. Select the Loop to be configured (1 - 8).
4. Select the loop parameters. The respective loop parameter screen will be shown:
Loop firmware version :

<Loop n>
Loop Type : ARGUS
Loop Wiring : 4 Wires
1.00
Figure 33 - Loop parameters

5. Program the loop in accordance with the connected device type and circuitry (2 or 4 wires).
6. Press the button to confirm the setting and exit the screen
Note:
If you exit the screen using the Esc button, the setting WILL NOT BE SAVED!
7. Press Esc repeatedly until you return to the Programming menu.

8. Select Configuration, Modify Configuration, Auto Enroll, Loop
Loop N.
ENROLL DEVICES
RE-ADDRESS ALL.
1 2 3 4 5 6 7 8
: . . . . . . . .
: . . . . . . . .
Figure 34 - Loop programming screen

9. Enter a + sign in the programming field that corresponds to the loop concerned.
Use the cursor keys S and T to select/deselect the options and cursor keys W and X to move from one
loop to another.
If you select Auto-configuration, the control panel will enroll the devices connected to the loop using
the pre-assigned address (assigned by means of the VPU100) without making changes to the devices
enrolled during previous operations.
If you select the Re-addressing option, the previously assigned addresses will be deleted and new
addresses will be given. All previously programmed data will be cleared.
10. Press - the panel will show the summary screen and ask for permission to continue.
11. Press to start the Auto-configuration phase.
B.5.2 Addressing detectors using the VPU100

Work carefully through the following steps:
1. Remove the detector from its base (twist off).
Argus Devices
51
Installation manual
2. Fit the detector into the VPU100 (twist on).

3. Press any button on the VPU100 to switch On the unit.
4. Using the scroll keys, select an address (1-240) then press the WRITE button (top left) to confirm
the selection.
Note:
240 addresses are available. Address entry errors can be corrected by simply readdressing the device
(deletion not required).
5. Remove the detector from the VPU100 and fit it to its placement.
B.5.3 Addressing detectors using the VPU100

1. Extract terminals 1- 4 from the module.
2. Connect the VPU cable to the module, positive to terminal 1 and negative to terminal 3.
3. Press any button on the VPU to switch On the unit.
4. Using the scroll keys, select an address (1-240) then press the WRITE button (top left) to confirm
the selection.
Note:
240 addresses are available. Address entry errors can be corrected by simply readdressing the device
(deletion not required).
5. Disconnect the VPU100 wires and reconnect the module to the Loop.
Figure 35 - Addressing modules using a VPU100
52
Argus Devices
Installation manual
Appendix C
Apollo Devices
Note:
The APOLLO devices accepted by this control panel do not have IMQ-SECURITY SYSTEMS certification,
refer to the instructions leaflet provided with each device.
Apollo devices are not equipped with built-in loop isolators (that is, unless otherwise specified). Therefore,
you must install loop isolators in such way as to avoid the loss of devices in the event of short-circuit.
C.1
Devices
C.1.1
Detectors: XP95 series
Note:
XP95 series detectors are especially designed to operate with a sensibility of 55 (sensibility at default).
Sensibility adjustment should be made only when absolutely essential, as any change may lead to delays
in loop response time.
Model
Name
Description
55000-885
XP95 Multisensor detector
Smoke/Temperature detector
55000-600
XP95 Smoke detector
55000-500
XP95 Smoke detector
Ionization smoke detector
55000-400
XP95 Heat detector
Fixed temperature detector
55000-401
XP95 Heat detector
High temperature detector
55000-640
XP95 I.S. Smoke detector
Intrinsic security smoke detector
55000-440
XP95 I.S.Heat detector
Intrinsic security heat detector
55000-540
XP95 I.S.Ionization smoke detector
Intrinsic security ionization smoke detector
C.1.2
Detectors: Discovery series
Model
Name
Description
58000-600
Discovery smoke detector
58000-400
Discovery heat detector
Low profile heat detector
58000-700
Discovery multisensor detector
Optical smoke and temperature detector
58000-300
Discovery CO detector
Carbon monoxide detector
58000-500
Discovery smoke detector
Ionization smoke detector
C.1.3
Detectors: Xplorer series
Note:
Xplorer series detectors are especially designed to operate with a sensibility of 55 (sensibility at default).
Sensibility adjustment should be made only when absolutely essential, as any change may lead to delays
in loop response time.
Model
Name
Description
59000-405
Heat detector
Heat detector with standard base
59000-406
LED heat detector
Heat detector with LED driver base
Apollo Devices
53
Installation manual
59000-407
Sounder Heat detector
Heat detector with sounder base
59000-415
Heat detector
High temperature heat detector with standard base
59000-416
LED heat detector
High temperature heat detector with LED driver base
59000-417
Sounder Heat detector
High temperature heat detector with base sounder
59000-605
Smoke detector
Optical smoke detector with standard base
59000-606
LED smoke detector
Optical smoke detector with LED driver base
59000-607
Sounder smoke detector
Optical smoke detector with base sounder
C.2
Device bases
Model
Name
Description
45681-210
Base
XP95/DISCOVERY mounting base
45681-215
XP95 I.S. Mounting base
Intrinsic security mounting base
45681-321
XP95/DISCOVERY isolating base
Isolating base for XP95 detectors
45681-242
XP95/DISCOVERY low-power relay base
Mounting base with relay
45681-250
XP95/DISCOVERY E-Z fit base
Large mounting base (150mm)
45681-276
Ancillary base sounder
Base with sounder
C.3
Accessories
Model
Name
Description
55000-720
XP95 Isolator
Isolator for loops
59000-700
XPlorer Isolator
Isolator for loops
55000-855
XP95 protocol translator
Protocol translator for intrinsically secure lines
C.4
Callpoints
Model
Name
Description
55000-905
XP95 Manual Callpoint
Manual callpoint for loops - wall mount
55000-906
XP95 Manual Callpoint
Manual callpoint for loops - flush mount
55000-940
XP95 I.S. Manual Callpoint
Intrinsic-security manual callpoint
58000-910
Discovery Manual Callpoint
Manual callpoint for loops - wall mount
58000-920
Discovery Manual Callpoint
Manual callpoint for loops - flush mount
59000-910
Xplorer Manual Callpoint
Xplorer series manual call point
C.5
Sounder and flashers
Model
Name
Description
55000-278
Sounder
Loop-powered sounder
55000-274
Weatherproof loop-powered sounder
Loop-powered sounder for outdoor installation
45681-265
Intelligent base sounder
Base sounder with its own address
55000-877
Loop-powered beacon
Beacon powered through the loop
45681-331
Loop-powered sounderflasher
Loop-powered sounder and beacon
54
Apollo Devices
Installation manual
C.6
Modules
Model
Name
Description
55000-809
XP95 Switch monitor plus
Module with 1 input with delay and reset output for waterflow
detectors (waterflow alarm)
55000-810
XP95 Switch monitor
Single input module
55000-813
XP95 Zone monitor
Conventional detector interface module
55000-818
XP95 Input/Output module
Module with 1 relay output + 1 supervised input + 1 nonsupervised input
55000-819
XP95 Output module
Module with 1 relay output
55000-823
XP95 Sounder control unit
Module with 1 output for externally-powered sounder control
55000-875
XP95 Mains switch input/output
Module with 1 supervised input + 1 relay x 220V
55000-832
XP95 Mini switch monitor (interrupt)
Reduced-size input module (interrupt)
55000-833
XP95 Mini switch monitor (interrupt)
Reduced-size input module
59000-810
XPlorer Output unit
XPlorer non-supervised output module
59000-820
XPlorer Switch monitor
Supervised input module
C.7
DIN rail modules
Model
Name
Description
55000-803
XP95 DIN rail input/output unit
DIN rail mount module with 1 input + 1 output
55000-804
XP95 DIN rail input/output unit
DIN rail mount module with 1 output
55000-821
XP95 DIN rail switch monitor plus
DIN rail mount module with 1 delayed input and reset output
for waterflow detectors (waterflow alarm)
55000-822
XP95 DIN rail switch monitor plus
DIN rail mount module with 1 output
55000-812
XP95 DIN rail zone monitor (with isolator)
DIN rail mount interface module for conventional zones (with

isolator)
55000-826
XP95 DIN rail sounder control unit
DIN rail mount module with 1 output for externally-powered

sounder-control
55000-802
XP95 DIN rail dual isolator
DIN rail mount dual isolator
C.8
Modules with isolators
Model
Name
Description
55000-841
XP95 Switch monitor plus with isolator
DIN rail mount module with 1 delayed input and reset output for waterflow
detectors (waterflow alarm)
55000-843
XP95 Switch monitor with isolator
Single input module with isolator
55000-845
XP95 Zone monitor with isolator
Interface module with isolator for conventional zones
55000-847
XP95 input/output module with isolator
Module with 1 relay output + 1 supervised input + 1 non-supervised input

(opto-isolated)
55000-849
XP95 Output unit with isolator
Module with 2 relay outputs with isolator
55000-852
XP95 Sounder control unit with isolator
Single output module with isolator for self-powered sounder control
C.9
Configuring Apollo devices
Every Apollo device requires an address to identify it on the loop. Apollo devices must be addressed
manually, as follows.
C.9.1
Addressing Apollo detectors
You can address Apollo detectors using the incorporated Xpert cards.
Apollo Devices
55
Installation manual
1. Remove the detector from its base (twist off).

2. Using a flat-bladed screwdriver or similar tool, push the locking tab and slide the Xpert card out of its
holder.
3. Using a flat-bladed screwdriver or similar tool, remove the pips in such way as to assign an address to
the Xpert card (refer to the Address Table in the device instructions).
Note:
126 addresses are available.
4. Using a felt-tip pen or printing device, write/print the respective address on the break-off tags.
Note:
This labeling method will provide visual identification of the system detectors during the system
installation phase. When you think you have the system detectors properly wired and addressed, you can
either break off the tags or leave them for future reference.
5. Replace the card.

6. Fit the detector to its base.
C.9.2
Addressing APOLLO modules
You can address all modules in the APOLLO range (Input,Output, In/Out, Manual Callpoint/Sounder/
Flasher/Emergency Light, etc.) using the incorporated DIP switches (see following figure).
1. Using the On/Off position of the incorporated DIP switch (refer to the Address Table in the device
instructions), set the module address (from 1 to 126).
2. Connect the module to the motherboard.
56
Apollo Devices
Installation manual
Appendix D
Order Codes
Following are the order codes of INIM Electronics s.r.l. products:
Code
Description
DCMIINE0SLOOP
Installation Manual
DCMPINE0SLOOP
Programming Manual
DCMUINE0SLOOP
User Manual
IPS24140
Switching Power supply/Battery 4A@27.6Vdc
Link232F9F9
RS232 link
LinkUSBAB
USB cable for PC to INIM device connection
ProbeTH
Thermal probe for battery charge optimization
SmartLAN
Ethernet interface for internet connections (for TCP-IP and web-server)
SmartLAN/SF
Ethernet interface for internet connections (for TCP-IP)
SmartLeague
Programming and management software for INIM products (runs on Windows)
SmartLetUSee/LCD
Repeater: remote control panel with LCD
SmartLetUSee/LED
Remote LED panel
SmartLook
Control software application (runs under Windows) for INIM systems
SmartLoop/1010-G
Single loop, non-expandable control panel with command keypad and display
SmartLoop/1010-P
Single loop, non-expandable control panel, equipped with command keypad and
display, zone status LED pad and housing for optional SmartLoop/PRN thermal printer
SmartLoop/1010-S
NON-expandable single loop control panel, with unequipped flush front
SmartLoop/2080-G
Two-loop control panel, expandable to 8, equipped with command keypad and display
SmartLoop/2080-P
Two-loop control panel, expandable to 8, equipped with command keypad and

display,
zone status LED pad and housing for optional SmartLoop/PRN thermal printer
SmartLoop/2080-S
Two-loop control panel, expandable to 8, with unequipped flush front
SmartLoop/2L
OpenLoop expansion board
SmartLoop/INOUT
Input/Output expansion board
SmartLoop/NET
Board for SmartLoop control-panel network connections (HorNet)
SmartLoop/PSTN
Voice and digital PSTN dialler board
Order Codes
57
Installation manual
Notes:
58
Notes:
Installation manual
59
via Fosso Antico Loc. Centobuchi

63076 Monteprandone (AP) ITALY
Tel. +39 0735 705007 _ Fax +39 0735 704912
info@inim.biz _ www.inim.biz
DCMIINE0SLOOP-R302-20120418

SmartLoop Fire Panels

Uploaded by

Copyright:

Available Formats

SmartLoop Fire Panels

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SmartLoop Fire Panels

Uploaded by

Copyright:

Available Formats

EN 54-2

European directive compliance

General information ............................................................ 10

Device management ........................................................... 15

Powering up the system ...................................................... 40

Testing wiring integrity 40

Fault NAC, alarm or fault output trouble 43

Application and use

[B] Repeater SmartLetUSee/LCD (accessory item)

Other parts of the system

Point: synonym and definition of a loop device (detector, etc.).

In order to validate the IMQ-SECURITY SYSTEMS certification, and in

About the SmartLoop fire alarm panel series

Figure 2 - SmartLoop Series

Description of the models

Manages up to 240 zones per panel with network-zone architecture feature

The motherboard provides housing for:

Installation manual (this manual)

Title: SmartLoop Installation Manual

SmartLoop firmware version: 2.0.x

Operator classification - Access Levels

The default PIN code is 00004.

Intellectual property rights

Testing the system

Note to the installer

2.11.1 Glossary and terminology

2.11.2 Graphic conventions

Text in italics: indicates the title of a chapter, section, paragraph, table

Representation of a part of the system or video object.

CANC, ESC, RESET

Computer or control panel keys.

The attached notes contain important information about the text.

Device identification details

Figure 3 - Data labe

Manufacturer: INIM Electronics s.r.l.

EN54-4: 1997/ A2: 2006

Manufacturer: INIM Electronics s.r.l.

Options with requirements:

Options with requirements:

Manufacturer: INIM Electronics s.r.l.

Manufacturer: INIM Electronics s.r.l.

EN54-4: 1997/ A2: 2006

2.14.2 Managing electronic devices

2.14.3 Connecting the apparatus

2.14.4 Replacement and disposal of used devices

Product handling and storage

Unpacking the device

Inside the box

Inside the box you will find

The package does not include:

Front panel with display, keys and signalling LEDs

Key location for the Level 2 access key

SmartLoop/PRN Thermal printer

Securing screws for the front cover

Cable entries (located on all sides of the enclosure)

SmartLoop/P and SmartLoop/G only

Figure 6 - About the motherboard

Loop 1 status LED

Loop 2 status LED

SmartLoop/2L board connector