1.25Gbps SFP Optical Transceiver, 10km Reach: Features

SFP-7010-31
1.25Gbps SFP Optical Transceiver, 10km Reach

Features
Dual data-rate of 1.25Gbps/1.063Gbps operation
1310nm FP laser and PIN photo detector for 10km transmission
Compliant with SFP MSA and SFF-8472 with duplex LC receptacle
Digital Diagnostic Monitoring:
Internal Calibration or External Calibration
Compatible with SONET OC-24-LR-1
Compatible with RoHS
+3.3V single power supply
Operating case temperature:
Standard : 0 to +70C
Extended : -20 to +85C
Industrial : -40 to +85C
Applications
Gigabit Ethernet
Fiber Channel
Switch to Switch interface
Switched backplane applications
Router/Server interface
Other optical transmission systems
Description
The SFP transceivers are high performance, cost effective modules supporting dual data-rate of
1.25Gbps/1.0625Gbps and 10km transmission distance with SMF.
The transceiver consists of three sections: a FP laser transmitter, a PIN photodiode integrated with a
trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety
requirements.
The transceivers are compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further
information, please refer to SFP MSA.
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA
www.robofiber.com
Page 1 of 9
Rev.1.2 Oct 13/2012
TD+/TxFault
TxDis
LD Driver
LD
Post Amp
PIN+TIA
LOS
RD+/-
Vcc
SCL
SDA
MCU
EEPROM
ADC/DAC
Temp
Absolute Maximum Ratings

Table 1 - Absolute Maximum Ratings
Parameter
Symbol
Min
Max
Unit
Supply Voltage
Vcc
-0.5
4.5
Storage Temperature
Ts
-40
+85
Operating Humidity
85
Recommended Operating Conditions

Table 2 - Recommended Operating Conditions
Parameter
Symbol
Standard
Operating Case Temperature
Tc
Industrial
Power Supply Voltage
Vcc
Power Supply Current
Icc
Min
Typical
Max
Unit
+70
-20
+85
-40
+85
3.47
300
mA
3.13
3.3
Gigabit Ethernet
1.25
Fiber Channel
1.063
Data Rate

www.robofiber.com
Page 2 of 9
Rev.1.2 Oct 13/2012
Gbps
Optical and Electrical Characteristics

SFP-7010-31: (FP and PIN, 1310nm, 10km Reach)
Table 3 - Optical and Electrical Characteristics
Parameter
Symbol
Min
Typical
Max
Unit
1310
1360
nm
nm
-3
dBm
Notes
Transmitter
Centre Wavelength
Spectral Width (RMS)
Average Output Power
Pout
-9
Extinction Ratio
ER
Optical Rise/Fall Time (20%~80%)
tr/tf
Data Input Swing Differential
VIN
400
Input Differential Impedance
ZIN
90
1260
dB
100
0.26
ns
1800
mV
110
Disable
2.0
Vcc
Enable
0.8
Fault
2.0
Vcc
Normal
0.8
1580
nm
-23
dBm
dBm
TX Disable
TX Fault
Receiver
Centre Wavelength
1260
Receiver Sensitivity
0
Receiver Overload
LOS De-Assert
LOSD
LOS Assert
LOSA
LOS
-35
dBm
dBm
dB
Vout
400
1800
mV
High
2.0
Vcc
0.8
LOS Hysteresis
Data Output Swing Differential
-24
Low
Notes:
1. The optical power is launched into SMF.
2. PECL input, internally AC-coupled and terminated.
7
-12
3. Measured with a PRBS 2 -1 test pattern @1250Mbps, BER 110 .
4. Internally AC-coupled.

www.robofiber.com
Page 3 of 9
Rev.1.2 Oct 13/2012
Timing and Electrical

Table 4 - Timing and Electrical
Parameter
Symbol
Min
Typical
Max
Unit
Tx Disable Negate Time
t_on
ms
Tx Disable Assert Time
t_off
10
Time To Initialize, including Reset of Tx Fault
t_init
300
ms
Tx Fault Assert Time
t_fault
100
Tx Disable To Reset
t_reset
10
LOS Assert Time
t_loss_on
100
LOS De-assert Time
t_loss_off
100
Serial ID Clock Rate
f_serial_clock
400
KHz
Vcc
0.8
MOD_DEF (0:2)-High
VH
MOD_DEF (0:2)-Low
VL
Diagnostics
Table 5 Diagnostics Specification
Parameter
Temperature
Range
0 to +70
-40 to +85
Unit
Accuracy
Calibration
3C
Internal / External
Voltage
3.0 to 3.6
3%
Internal / External
Bias Current
0 to 100
mA
10%
Internal / External
TX Power
-9 to -3
dBm
3dB
Internal / External
RX Power
-23 to 0
dBm
3dB
Internal / External

www.robofiber.com
Page 4 of 9
Rev.1.2 Oct 13/2012
Digital Diagnostic Memory Map

The transceivers provide serial ID memory contents and diagnostic information about the present
operating conditions by the 2-wire serial interface (SCL, SDA).
The diagnostic information with internal calibration or external calibration all are implemented,
including received power monitoring, transmitted power monitoring, bias current monitoring, supply
voltage monitoring and temperature monitoring.
The digital diagnostic memory map specific data field defines as following.

www.robofiber.com
Page 5 of 9
Rev.1.2 Oct 13/2012
Pin Definitions
Pin Diagram

www.robofiber.com
Page 6 of 9
Rev.1.2 Oct 13/2012
Pin Descriptions
Pin
Signal Name
Description
Plug Seq.
Notes
VEET
Transmitter Ground
TX FAULT
Transmitter Fault Indication
Note 1
TX DISABLE
Transmitter Disable
Note 2
MOD_DEF(2)
SDA Serial Data Signal
Note 3
MOD_DEF(1)
SCL Serial Clock Signal
Note 3
MOD_DEF(0)
TTL Low
Note 3
Rate Select
Not Connected
LOS
Loss of Signal
VEER
Receiver ground
Note 4
10
VEER
Receiver ground
11
VEER
Receiver ground
12
RD-
Inv. Received Data Out
Note 5
13
RD+
Received Data Out
Note 5
14
VEER
Receiver ground
15
VCCR
Receiver Power Supply
16
VCCT
Transmitter Power Supply
17
VEET
Transmitter Ground
18
TD+
Transmit Data In
Note 6
19
TD-
Inv. Transmit Data In
Note 6
20
VEET
Transmitter Ground
1
Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10k resistor on the host board to a voltage
between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low
state, the output will be pulled to less than 0.8V.
2) TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a
4.7k~10k resistor. Its states are:
Low (0 to 0.8V):
Transmitter on
(>0.8V, < 2.0V):
Undefined
High (2.0 to 3.465V):
Transmitter Disabled
Open:
Transmitter Disabled
3) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7k~10k resistor on the host
board. The pull-up voltage shall be VccT or VccR.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is the clock line of two wire serial interface for serial ID
Mod-Def 2 is the data line of two wire serial interface for serial ID
4) LOS is an open collector output, which should be pulled up with a 4.7k~10k resistor. Pull up voltage between 2.0V and
Vcc+0.3V. Logic 1 indicates loss of signal; Logic 0 indicates normal operation. In the low state, the output will be pulled to
less than 0.8V.
5) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be
terminated with 100 (differential) at the user SERDES.
6) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100 differential
termination inside the module.

www.robofiber.com
Page 7 of 9
Rev.1.2 Oct 13/2012
Recommended Interface Circuit

www.robofiber.com
Page 8 of 9
Rev.1.2 Oct 13/2012
Mechanical Dimensions
Ordering information
Part Number
SFP-7010-31
SFP-7010-31-X
SFP-7010-31-XDD
SFP-7010-31-I
SFP-7010-31-IDD
Product Description
1310nm, 1.25Gbps, 20km,
1310nm, 1.25Gbps, 20km,
1310nm, 1.25Gbps, 20km,
1310nm, 1.25Gbps, 20km,
1310nm, 1.25Gbps, 20km,
0C ~ +70C, With Digital Diagnostic Monitoring

-20C ~ +85C
-20C ~ +85C, With Digital Diagnostic Monitoring
-40C ~ +85C
-40C ~ +85C, With Digital Diagnostic Monitoring
E-mail: sales@robofiber.com

www.robofiber.com
Page 9 of 9
Rev.1.2 Oct 13/2012

1.25Gbps SFP Optical Transceiver, 10km Reach: Features

Uploaded by

Copyright:

Available Formats

1.25Gbps SFP Optical Transceiver, 10km Reach: Features

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1.25Gbps SFP Optical Transceiver, 10km Reach: Features

Uploaded by

Copyright:

Available Formats

SFP-7010-31

1.25Gbps SFP Optical Transceiver, 10km Reach

Rev.1.2 Oct 13/2012

Absolute Maximum Ratings

Recommended Operating Conditions

Power Supply Voltage

Power Supply Current

Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA

Rev.1.2 Oct 13/2012

Optical and Electrical Characteristics

Spectral Width (RMS)

Average Output Power

Optical Rise/Fall Time (20%~80%)

Data Input Swing Differential

Input Differential Impedance

Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA

Rev.1.2 Oct 13/2012

Timing and Electrical

Tx Disable Negate Time

Tx Disable Assert Time

Time To Initialize, including Reset of Tx Fault

Tx Fault Assert Time

LOS Assert Time

LOS De-assert Time

Serial ID Clock Rate

Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA

Rev.1.2 Oct 13/2012

Digital Diagnostic Memory Map

Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA

Rev.1.2 Oct 13/2012

Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA

Rev.1.2 Oct 13/2012

Transmitter Fault Indication

SDA Serial Data Signal

SCL Serial Clock Signal

Inv. Received Data Out

Received Data Out

Receiver Power Supply

Transmitter Power Supply

Inv. Transmit Data In

Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA

Rev.1.2 Oct 13/2012

Recommended Interface Circuit

Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA

Rev.1.2 Oct 13/2012

0C ~ +70C, With Digital Diagnostic Monitoring

Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA

Rev.1.2 Oct 13/2012

You might also like