MALAYSIAN STANDARDS APPROVED ON 06/01/2014 BY THE MINISTRY

OF SCIENCE, TECHNOLOGY AND INNOVATION IN ACCORDANCE

WITH THE STANDARDS OF MALAYSIA ACT (ACT 549)

New Malaysian Standard

ISC B : Chemicals and Materials
1. MS 2555:2014
Liquid fertilizers - Specification
2. MS 2559:2014
Limestone, quicklime, hydrated lime and putty lime - Methods for physical testing

ISC D : Building, Construction and Civil Engineering

1. MS 2526-10:2014
Urban stormwater management - Part 10: Gross pollutant traps
2. MS 2526-11:2014
Urban stormwater management - Part 11: Water quality ponds and wetlands
3. MS 2526-12:2014
Urban stormwater management - Part 12: Erosion and sediment control
4. MS 2526-4:2014
Urban stormwater management - Part 4: Roof and property drainage
5. MS 2526-5:2014
Urban stormwater management - Part 5: On-site detention
6. MS 2526-6:2014
Urban stormwater management - Part 6: Rainwater harvesting
7. MS 2526-7:2014
Urban stormwater management - Part 7: Detention ponds
8. MS 2545:2014
Flush valves - Specification
9. MS 2551:2014
Speed bump - Guidelines for planning and design

10. MS 2562:2014
Moulded expanded perlite block and pipe thermal insulation - Specification
11. MS EN 13791:2014
Assessment of in-situ compressive strength in structures and precast concrete components

ISC E : Generation, Transmission and Distribution of Energy

1. MS 60269-5:2014
Low-voltage fuses - Part 5: Guidance for the application of low-voltage fuses
2. MS 61850-6:2014
Communication networks and systems for power utility automation - Part 6: Configuration
description language for communication in electrical substations related to IEDs (IEC 618506:2009, MOD)
3. MS 61850-7-2:2014
Communication networks and systems for power utility automation - Part 7-2: Basic
communication structure - Abstract communication service interface (ACSI) (IEC 61850-7-2:2010,
MOD)
4. MS 61850-8-1:2014
Communication networks and systems for power utility automation - Part 8 -1: Specific
communication service mapping (SCSM) - Mappings to MMS (ISO 9506-1 and ISO 9506-2) and
to ISO/IEC 8802-3 (IEC 61850-8-1:2011, MOD)
5. MS IEC 60243-1:2014
Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies (IEC
60243-1:2013, IDT)
6. MS IEC 60243-2:2014
Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests
using direct voltage (IEC 60243-2:2001, IDT)
7. MS IEC 60243-3:2014
Electric strength of insulating materials - Test methods - Part 3: Additional requirements for 1.2/50
s impulse tests (IEC 60243-3:2001, IDT)
8. MS IEC 60664-1:2014
Insulation coordination for equipment within low-voltage systems - Part 1: Principles,
requirements and tests (IEC 60664-1:2007, IDT)
9. MS IEC 62056-53:2014
Electricity metering - Data exchange for meter reading, tariff and load control - Part 53: COSEM
application layer (IEC 62056-53:2006, IDT)
10. MS IEC 62056-61:2014

Electricity metering - Data exchange for meter reading, tariff and load control - Part 61: Object
identification system (OBIS) (IEC 62056-61:2006, IDT)

ISC F : Mechanical Engineering

1. MS EN 1273:2014
Child use and care articles - Baby walking frames - Safety requirements and test methods
2. MS ISO 3452-1:2014
Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1:2013, IDT)
3. MS ISO 3452-4:2014
Non-destructive testing - Penetrant testing - Part 4: Equipment (ISO 3452-4:1998. IDT)
4. MS ISO 3452-5:2014
Non-destructive testing - Penetrant testing - Part 5: Penetrant testing at temperatures higher than
50 C (ISO 3452-5:2008, IDT)
5. MS ISO 3452-6:2014
Non-destructive testing - Penetrant testing - Part 6: Penetrant testing at temperatures lower than
10 C (ISO 3452-6:2008, IDT)
6. MS ISO 9712:2014
Non-destructive testing - Qualification and certification of NDT personnel ISO 9712:2012, IDT)

ISC G : Information Technology, Communications and Multimedia

1. MS 2539:2014
Information technology- Security techniques - Information security management guidelines for
industrial automation and control system (IACS) based on MS ISO/IEC 27002
2. MS ISO/IEC 27003:2014
Information technology - Security techniques - Information security management system
implementation guidance (ISO/IEC 27003:2010, IDT)
3. MS ISO/IEC 27004:2014
Information technology - Security techniques - Information security management - Measurement
(ISO/IEC 27004:2009, IDT)

ISC H : Petroleum and Gas

1. MS 2544:2014
Oil and gas production facilities - Protective coatings and linings - Specification

ISC J : Plastics and Plastics Products

1. MS 2548-1:2014
Plastics piping system for non-pressure underground drainage and sewerage - Structured-wall
piping systems of unplasticised poly(vinyl chloride)(PVC-U), polypropylene (PP) and polyethylene
(PE) - Part 1: Dimensions
2. MS 2548-2:2014
Plastics piping system for non-pressure underground drainage and sewerage - Structured-wall
piping systems of unplasticised poly(vinyl chloride)(PVC-U), polypropylene (PP) and polyethylene
(PE) - Part 2: Technical delivery specifications
3. MS 2549:2014
Plastics - Film and sheeting - Metallised cast polypropylene (MCPP) film - Specification
4. MS 2557:2014
Plastics - Film and sheeting - Biaxially oriented poly(ethylene terephthalate) (PET) films (ISO
15988:2003, MOD)
5. MS 2566:2014
Plastics - Film and sheeting - Vacuum metallised biaxially oriented poly(ethylene terephthalate)
(MPET) films - Specification
6. MS 2567:2014
Plastics Film and sheeting - Vacuum metallised biaxially oriented polypropylene (MBOPP)
films- Specification

ISC K : Packaging and Logistics

1. MS 1990-4-9:2014
Manual of tests and criteria for transport of dangerous goods - Part 4: Classification procedures,
test methods and criteria relating to Class 2, Class 3, Class 4, Division 5.1, Class 8 and Class 9 Section 9: Class 9
2. MS 1990-5:2014
Manual of tests and criteria for transport of dangerous goods - Part 5: Test methods concerning
transport equipment

ISC L : Road Vehicles

1. MS 2395-2:2014
Road vehicles - End-of life vehicles - Part 2: Hazardous substances - Requirements and vehicle
ranking
2. MS 2563:2014
Goods vehicles - Chassis frame modification - Code of Practice

ISC O : Organisational Management

1. MS 2550:2014
Cleaning performance - Commercial and public buildings

ISC P : Metallic Materials and Semi-Finished Products

1. MS 2543:2014
Electrolytic zinc-coated steel sheet and strip
2. MS EN 10080:2014
Steel for the reinforcement of concrete - Weldable reinforcing steel - General
3. MS ISO 13887:2014
Cold-reduced steel sheet of higher yield strength with improved formability (ISO 13887:2011, IDT)
4. MS ISO 14590:2014
Cold-reduced steel sheet of high tensile strength and low yield point with improved formability
(ISO 14590:2005, IDT)
5. MS ISO 4960:2014
Cold-reduced carbon steel strip with a mass fraction of carbon over 0.25 % (ISO 4960:2007, IDT)
6. MS ISO 5001:2014
Cold-reduced carbon steel sheet for vitreous enamelling (ISO 5001:2012, IDT)

ISC R : Medical Devices and Facilities for Healthcare

1. MS 2561:2014
Radiation protection and performance evaluation of PET-CT imaging - Guidelines

ISC S : Electrical and Electronics Equipments and Accessories

1. MS 2436-2-4:2014
Alarm systems - Intrusion and hold-up systems - Part 2-4: Requirements for combined passive
infrared and microwave detectors
2. MS 2436-2-6:2014
Alarm systems - Instrusion and hold-up systems - Part 2-6: Opening contacts (magnetic)
3. MS 2436-2-7-1:2014
Alarm systems -Intrusion and hold-up systems - Part 2-7-1: Intrusion detectors - Glass break
detectors (acoustic)
4. MS 2436-2-7-2:2014
Alarm systems - Intrusion and hold-up systems - Part 2-7-2: Intrusion detectors - Glass break

detectors (passive)

5. MS 2436-4:2014
Alarm systems - Intrusion and hold-up systems - Part 4: Warning devices
6. MS 62471-2:2014
Photobiological safety of lamps and lamp systems - Part 2: Guidance on manufacturing
requirements relating to non-laser optical radiation safety
7. MS IEC 60034-2-1:2014
Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency
from tests (excluding machines for traction vehicles) (IEC 60034-2-1:2007, IDT)
8. MS IEC 60034-30:2014
Rotating electrical machines - Part 30: Efficiency classes of single-speed, three-phase, cageinduction motors (IE-code) (IEC 60034-30:2008, IDT)

ISC U : Food, Food Products and Food Safety

1. MS 2565:2014
Halal packaging - General guidelines

ISC W : Occupational Safety and Health

1. MS 2552:2014
Respiratory protective devices - Mouthpiece assemblies - Requirements, testing, marking
2. MS 2553:2014
Respiratory protective devices - Particle filters - Requirements, testing, marking
3. MS 2554:2014
Respiratory protective devices - Gas filter(s) and combined filter(s) - Requirements, testing,
marking

ISC Y : Quality Management and Quality Assurance

1. MS ISO 10004:2014
Quality management - Customer satisfaction - Guidelines for monitoring and measuring (ISO
10004:2012, IDT)
2. MS ISO 10018:2014
Quality management - Guidelines on people involvement and competence (ISO 10018:2012, IDT)

ISC Z : Environmental Management

1. MS 2547:2014
Landfill safe closure - Requirements
2. MS 2564:2014
Performance criteria and test procedures for continuous emission monitoring systems (CEMS)

Revised Malaysian Standard (1st Revision)

ISC B : Chemicals and Materials
1. MS 1526:2014
Floor liquid detergents - Specification (First revision)
2. MS 174:2014
Formic acid - Technical grade - Specification (First revision)
3. MS 177:2014
Hydrochloric acid - Technical grade - Specification (First revision)

ISC D : Building, Construction and Civil Engineering

1. MS 2282-1:2014
Masonry units - Specification - Part 1: Fired clay masonry units (First revision)
2. MS EN 450-1:2014
Fly ash for concrete - Part 1: Definition, specifications and conformity criteria
3. MS EN 450-2:2014
Fly ash for concrete - Part 2: Conformity evaluation
4. MS ISO 13006:2014
Ceramic tiles - Definitions, classification, characteristics and marking (First revision) (ISO
13006:2012, IDT)

ISC E : Generation, Transmission and Distribution of Energy

1. MS IEC 61000-3-2:2014
Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions
(equipment input current <= 16 A per phase) (First revision) (IEC 61000-3-2:2009, IDT)
2. MS IEC 61000-4-30:2014
Electromagnetic compatibility (EMC) - Part 4-30: Testing and measurement techniques - Power

quality measurement methods (First revision) (IEC 61000-4-30:2008, IDT)

ISC F : Mechanical Engineering

1. MS 2560:2014
Gas cylinders - Safe handling (First revision) (ISO 11625:2007, MOD)
2. MS ISO 225:2014
Fasteners - Bolts, screws, studs and nuts - Symbols and descriptions of dimensions (First
revision) (ISO 225:2010, IDT)
3. MS ISO 4306-1:2014
Cranes - Vocabulary - Part 1: General (First Revision) (ISO 4306-1:2007, IDT)
4. MS ISO 4310:2014
Cranes - Test code and procedures (First revision) (ISO 4310:2009, IDT)

ISC I : Halal Standards

1. MS 1900:2014
Shariah-based quality management systems - Requirements with guidance(First revision)

ISC L : Road Vehicles

1. MS 1439:2014
Definitions of common terms used in the tyre industry - Pneumatic tyres (First revision)
2. MS 932:2014
Motorcycles - Rear view mirrors - Specification and installation (First revision)

ISC N : Rubber and Rubber Products

1. MS ISO 34-1:2014
Rubber, vulcanized or thermoplastic - Determination of tear strength - Part 1: Trouser, angle and
crescent test pieces (First revision) (ISO 34-1:2010, IDT)

ISC S : Electrical and Electronics Equipments and Accessories

1. MS 1597-2-5:2014
Household and similar electrical appliances - Safety - Part 2-5: Particular requirements for
dishwashers (First revision) (IEC 60335-2-5: 2008, MOD)
2. MS 60335-2-98:2014
Household and similar electrical appliances - Safety - Part 2-98: Particular requirements for

humidifiers (First revision) (IEC 60335-2-98: 2008, IDT)

3. MS IEC 60034-3:2014
Rotating electrical machines - Part 3: Specific requirements for synchronous generators driven by
steam turbines or combustion gas turbines (First revision) (IEC 60034-3:2007, IDT)
4. MS IEC 60034-4:2014
Rotating electrical machines - Part 4: Methods for determining synchronous machine quantities
from tests (First revision) (IEC 60034-4:2008, IDT)
5. MS IEC 60335-2-101:2014
Household and similar electrical appliances - Safety - Part 2-101: Particular requirements for
vaporizers (First revision) (IEC 60335-2-101: 2008, IDT)
6. MS IEC 60335-2-12:2014
Household and similar electrical appliances - Safety - Part 2-12: Particular requirements for
warming plates and similar appliances (First revision) (IEC 60335-2-12: 2008, IDT)
7. MS IEC 60335-2-85:2014
Household and similar electrical appliances - Safety - Part 2-85: Particular requirements for fabric
steamers (First revision) (IEC 60335-2-85:2008, IDT)

ISC U : Food, Food Products and Food Safety

1. MS 547:2014
Fresh, chilled and frozen pork - Specification (First revision)

ISC W : Occupational Safety and Health

1. MS 2558:2014
Safety and health signage used in the workplace - Specification (First revision)
2. MS ISO 13849-2:2014
Safety of machinery - Safety-related parts of control systems - Part 2: Validation (First Revision)
(ISO 13849-2:2012, IDT)

ISC Y : Quality Management and Quality Assurance

1. MS ISO 19011:2014
Guidelines for auditing management systems (First revision) (ISO 19011:2011, IDT)

Revised Malaysian Standard (2nd Revision)

ISC B : Chemicals and Materials

1. MS 1285:2014
Glass cleaner - Specification (Second revision)
2. MS 791:2014
Liquid detergent for household hand dish washing - Specification (Second revision)

ISC D : Building, Construction and Civil Engineering

1. MS 1525:2014
Energy efficiency and use of renewable energy for non-residential buildings - Code of practice
(Second revision)

ISC F : Mechanical Engineering

1. MS 1315-1:2014
Office furniture - Storage furniture - Part 1: Safety requirements (Second revision)
2. MS 1315-2:2014
Office furniture - Storage furniture - Part 2: Determination of stability and strength of the structure
(Second revision)
3. MS 771:2014
Automotive leaf spring - Specification (Second revision)

ISC J : Plastics and Plastics Products

1. MS 1421:2014
Test method for haze and luminous transmittance of transparent plastics (Second revision)

ISC P : Metallic Materials and Semi-Finished Products

1. MS 1196:2014
Continuous hot-dip aluminium/zinc alloy-coated sheet of commercial, drawing and structural
qualities (Second revision)

ISC R : Medical Devices and Facilities for Healthcare

1. MS ISO 15189:2014
Medical laboratories - Requirements for quality and competence (Second revision) (ISO
15189:2012, IDT)

ISC S : Electrical and Electronics Equipments and Accessories

1. MS 1597-2-75:2014
Household and similar electrical appliances - Safety - Part 2-75: Particular requirements for
commercial dispensing appliances and vending machines (Second revision) (IEC 60335-275:2012, MOD)
2. MS 60335-2-25:2014
Household and similar electrical appliances - Safety - Part 2-25: Particular requirements for
microwave ovens, including combination microwave ovens (Second revision) (IEC 60335-2-25:
2010, IDT)
3. MS IEC 60335-2-11:2014
Household and similar electrical appliances - Safety - Part 2-11: Particular requirements for
tumble dryers (Second revision) (IEC 60335-2-11:2012, IDT)
4. MS IEC 60335-2-14:2014
Household and similar electrical appliances - Safety - Part 2-14: Particular requirements for
kitchen machines (Second revision) (IEC 60335-2-14:2008, IDT)
5. MS IEC 60335-2-31:2014
Household and similar electrical appliances - Safety - Part 2-31: Particular requirements for range
hoods and other cooking fume extractors (Second revision) (IEC 60335-2-31:2009, IDT)
6. MS IEC 60335-2-32:2014
Household and similar electrical appliances - Safety - Part 2-32: Particular requirements for
massage appliances (Second revision) (IEC 60335-2-32:2008, IDT)
7. MS IEC 60335-2-36:2014
Household and similar electrical appliances - Safety - Part 2-36: Particular requirements for
commercial electric cooking ranges, ovens, hobs and hob elements (Second revision) (IEC
60335-2-36:2008, IDT)
8. MS IEC 60335-2-43:2014
Household and similar electrical appliances - Safety - Part 2-43: Particular requirements for
clothes dryers and towel rails (Second revision) (IEC 60335-2-43: 2008, IDT)
9. MS IEC 60335-2-65:2014
Household and similar electrical appliances - Safety - Part 2-65 : Particular requirements for aircleaning appliances (Second revision) (IEC 60335-2-65:2008, IDT)
10. MS IEC 60335-2-73:2014
Household and similar electrical appliances - Safety - Part 2-73: Particular requirements for fixed
immersion heaters (Second revision) (IEC 60335-2-73: 2009, IDT)

Revised Malaysian Standard (3rd Revision)

ISC J : Plastics and Plastics Products

1. MS 1225-1:2014
Polyethylene (PE) tanks for cold water storage - Part 1: Capacity up to 600 gal (third revision)

ISC N : Rubber and Rubber Products

1. MS 671:2014
Elastomeric bridge bearings - Specification and design (Third revision)

ISC S : Electrical and Electronics Equipments and Accessories

1. MS IEC 60335-2-6:2014
Household and similar electrical appliances - Safety - Part 2-6: Particular requirements for
stationary cooking ranges, hobs, ovens and similar appliances (Third revision) (IEC 60335-2-6:
2008, IDT)

Revised Malaysian Standard (4th Revision)

ISC P : Metallic Materials and Semi-Finished Products
1. MS 144:2014
Steel wire for the reinforcement of concrete products - Specification (Fourth revision)
2. MS 145:2014
Steel fabric for the reinforcement of concrete - Specification (Fourth revision)
3. MS 146:2014
Steel for the reinforcement of concrete - Weldable reinforcing steel - Bar, coil and decoiled
product - Specification (Fourth revision)

ISC S : Electrical and Electronics Equipments and Accessories

1. MS IEC 60335-2-9:2014
Household and similar electrical appliances - Safety - Part 2-9: Particular requirements for grills,
toasters and similar portable cooking appliances (Fourth revision) (IEC 60335-2-9:2008, IDT)