Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 835 views

    Samsung AQV Inverter Service Manual

    Uploaded by

    kelleterre
    The document discusses test mode operation, indoor and outdoor unit error displays, and setting installation options for air conditioners. Test mode allows checking component operation without temperature controls. Error displays identify sensor, motor, and communication issues. Installation options are set using the remote control display.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Samsung AQV Inverter Service Manual

    Uploaded by

    kelleterre
    835 views6 pages
    The document discusses test mode operation, indoor and outdoor unit error displays, and setting installation options for air conditioners. Test mode allows checking component operation without temperature controls. Error displays identify sensor, motor, and communication issues. Installation options are set using the remote control display.

    Original Description:

    Samsung-AQV-inverter-service-manual.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document discusses test mode operation, indoor and outdoor unit error displays, and setting installation options for air conditioners. Test mode allows checking component operation without temperature controls. Error displays identify sensor, motor, and communication issues. Installation options are set using the remote control display.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    835 views6 pages

    Samsung AQV Inverter Service Manual

    Uploaded by

    kelleterre
    The document discusses test mode operation, indoor and outdoor unit error displays, and setting installation options for air conditioners. Test mode allows checking component operation without temperature controls. Error displays identify sensor, motor, and communication issues. Installation options are set using the remote control display.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    3.

    Alignment and Adjustments


    3-1 Test Mode
    How to Approach Test Mode
    You can approach the Test Mode by pressing the on/off switch of
    indoor unit for 5 seconds.

    on/off switch

    Test Mode Operation Option


    After installing the air conditioner, check whether each subordinate is normally operated or not by operating the Test Mode.
    When an error occurs, display the Error Mode.
    Operation Mode : Cool mode. Operate the cool mode by operating the compressor by force without the compressor ON/OFF
    according to the set temperature/indoor temperature. (Do not follow the antifreeze control)
    Up-down louver : Up-down swing mode
    Indoor Fan : High

    Because the Test Mode operate the cool mode by force not related to the set temperature / indoor temperature, check
    whether each subordinate is operated normally or not after completing installation and must turn off the power of the
    air conditioner.

    Samsung Electronics

    3-1

    3-2 Indoor Display Error and Check Method


    LAMP
    Description

    OPERATION

    Indoor unit room temperature sensor error


    (open or short)
    Indoor unit heat exchanger temperature sensor error
    (open or short)

    TIMER

    TURBO

    Main Checking Point

    3-2P

    3-3P

    Indoor fan motor malfunction

    3-4P

    EEPROM error

    Option Setting

    Option error
    (option wasnt set up or option data error)

    Option Setting

    Outdoor unit error

    Remote Control on/off


    Outdoor Unit Power Reset

    : Lamp on,

    3-2

    : Lamp off, : Lamp blink

    Samsung Electronics

    3-3 Outdoor LED Error Display and Check Method


    No.

    LED Display

    Explanation

    Yellow

    Green

    Red

    Power off/ VDD NG

    IPM Over Current(O.C)

    Compressor Starting error

    Normal Operation

    Compressor Lock error

    DC-Link voltage under/over error

    Outdoor temperature sensor error

    Discharge over temperature

    10

    Discharge temperature sensor error

    11

    Current sensor error

    12

    Compressor limit error

    13

    Coil temperature sensor error

    14

    1min. Time out Communication

    15

    Fan error

    16

    OTP error

    17

    Compressor rotation error

    18

    Operation condition secession(Dual only)

    19

    DC-Link voltage sensor error

    20

    I_Trip error / PFC Over current

    21

    GAS Leak error

    22

    AC Line Zero Cross Signal out

    23

    Power ON reset(1sec)

    24

    Capacity miss match

    25

    Test Operation at Cooling Mode

    26

    Test Operation at Heating Mode

    Abnormal Serial communication

    : LED ON, : LED OFF, : LED BLINK

    Samsung Electronics

    3-3

    3-4 Setting Option Setup Method


    ex) Option No. :
    Step 1 : Enter the Option Setup mode.
    1st Take out the batteries of remote control.
    2nd Press the temperature
    the battery again.

    button simultaneously and insert

    3rd Make sure the remocon display shown as

    Step 2 : Enter the Option Setup mode and select your option according to the following procedure.

    1
    The default value is

    Otherwise, push the

    button to

    Every time you push the button, the display panel reads

    or

    repeatedly.

    Push the

    button to set the display panel to

    Every time you push the button, the display panel reads

    . . . repeatedly.

    Push the
    10

    button to set the display panel to

    Every time you push the button, the display panel reads

    . . . repeatedly.

    Push the

    button to set the display panel to

    Every time you push the button, the display panel reads

    . . . repeatedly.

    Push the

    button to set the display panel to

    Every time you push the button, the display panel reads
    Setting is not required if you must
    a value which has a

    default.

    . . . repeatedly.

    Push the

    button to set the display panel to

    Every time you push the button, the display panel reads

    . . . repeatedly.

    3-4

    Samsung Electronics

    Alignment and Adjustments

    7
    1
    Press

    Push the

    button, then the default value is

    button to set the display panel to

    Every time you push the button, the display panel reads

    . . . repeatedly.

    Push the

    button to set the display panel to

    Every time you push the button, the display panel reads

    . . . repeatedly.

    10

    Push the

    button to set the display panel to

    Every time you push the button, the display panel reads

    . . . repeatedly.

    11

    Push the

    button to set the display panel to

    Every time you push the button, the display panel reads

    . . . repeatedly.

    12
    Setting is not required if you must
    a value which has a

    Push the

    button to set the display panel to

    Every time you push the button, the display panel reads

    default.

    . . . repeatedly.

    Step 3 : Upon completion of the selection, check you made right selections.
    Press the Mode Selection key,
    to set the display part to and check the display part.
    The display part shows

    Press the Mode Selection key,


    The display part shows

    to set the display part to

    and check the display part.

    Step 4 : Pressing the ON/OFF button (


    )
    When pressing the operation ON/OFF key with the direction of remote control for unit, the sound Ding or Diriring
    is heard and the OPERATION ICON(
    ) lamp of the display is flickering at the same time, then the input of option is completed.
    (If the diriring sound isnt heard, try again pressing the ON/OFF button.)
    Step 5 : Unit operation test-run
    First, Remove the battery from the remote control.
    Second, Re-insert the battery into the remote control.
    Third, Press ON/OFF key with the direction of remote control for set.

    Error Mode
    1st
    2nd

    If all lamps of indoor unit are flickering, Plug out, plug in power plug again and press ON/OFF key to retry.
    If the unit is not working properly or all lamps are continuously flickering after setting the option code, see if the
    correct option code is set up for its model.

    Samsung Electronics

    3-5

    Alignment
    Operating Instructions
    and Adjustments
    and Installation

    OPTION ITEMS
    REMOCON

    SEG1

    SEG2

    SEG3

    SEG4

    SEG5

    SEG6

    SEG7

    SEG8

    SEG9

    AQV09NSAN
    AQV09FCN

    AQV12NSAN
    AQV12FCN

    MODEL

    3-6

    SEG10 SEG11 SEG12

    Samsung Electronics

    You might also like