Wasi Polar Eng

PV MOUNTING SYSTEM
FLAT ROOF
POLAR BEAR
We secure the sun
WASISOLAR
SOLARFLAT
FLATROOF
ROOFSYSTEM
SYSTEM
WASI
Roof connection
Flat roof
POLAR BEAR
Modular connection
Hexagonal nut with serration 9345-2-6
Support Polar Bear (Aluminium

End plate deector
or G90 Steel galvanized, optionally
(Aluminium or G 90 Steel galvanized)
with roof protection pad)
Hexagonal nut with serration 9345-2-10

Wind deector 69 inch or 73 inch
Hexagonal scew 933-2-10 x 30
(Aluminium or G90 Steel galvanized)
Claw 9675-5010005
European Business Partner of WASI Solar
POLAR BEAR FR: TECHNICAL DATA
Fig.: Polar Bear FR Gen II 10 Grad
Application
Flat roof (max slope 5 degrees)
Installation Speed
160-180 modules per day (3-person crew)
Module Tilt Angle
10 12 degrees (depending on module width)
Module clamps
Longitudinal direction (on the short side)
Basic Wind Speed
up to 193 km/h (Zone 4)
Array Platform Load
approx. 14 and 39 kg/m (distributed onto the unit surface)
Building height
up to 18.3 m (custom upon request)
Material
Aluminium or G90 Steel
Warranty (Standard)
10 years
WASI SOLAR FLAT ROOF SYSTEM
POLAR BEAR
1 - Polar Bear FR Gen II 10- innovative, aerodynamic construction with variable ballast
is part of a new generation of aerodynamic PV-assembly sys-
breakthrough is needed. A folding function for single modules
tems for at roofs that uses only 3 system components. Polar
simplies the module and roof maintenance - and thus helps
Bear is especially lightweight and can be quickly set up and
to keep the maintenance costs low.
3 - Polar Bear FR Gen II 10- all components

Art.No. / Figure
Article
Dimension
Variant /
Material
VPE
Description
Assembly of two
components consisting
of east-support
with thread connection
and roof protection pad
and a west-support
without thread connection.
Assembly of two
components consisting of
east-support
and a west-support
without thread connection.
9675-5010059
dissembled at low cost. The roof is ideally protected, no roof

Support
with
roof protection pad
2 - Polar Bear FR Gen II 10 - only three components
876,3 mm x
284,1 mm
(without
roof
protection
pad)
Aluminium
rubber
9675-5010081
SUPPORT
Support
without
roof protection pad
universal, module-independent design

exible row distances
876,3 mm x
284,1 mm
Aluminium
certied, location related ballast calculation of the system

due to rail-free construction, water can drain freely
more options to even roof slanting changes
available with installed roof protection pad
9675-5010082
pre-installed screws to assemble the wind deector

stainless steel fastener kit with just two nut and bolt sizes
Support
without
roof protection pad
876,3 mm x
284,1 mm
G90
steel
galvanized
Assembly of two
components, consisting of
east-support
and a west-support without
thread connection.
WIND DEFLECTOR
optimized construction enables an efcient module cooling
A-thermalized design for enhanced roof protection
chamfered edges and lightweight construction facilitate
common deector for Grizzly and Polar Bear
9675-2000135
/
9675-2000000
CLAW
patented claw, universal to all PanelClaw mounting systems
Roof
protection pad
for Polar Bear
support
876,3 mm x
200 mm x
9,5 mm
Roof
protection pad
for Polar Bear
support
900 mm x
416 mm x
10 mm
rubber
BsW
Plates
2 pieces per foot.

Directly for clicking it
into the foot.
1 piece per support.

not to click in, the support
is only placed on the roof
protection pad.
the concrete stones are usually not included in the delivery

scope and can only be ordered
upon request. For manufacture
we recommend a minimum
compressive strength of
35 MPA and frost resistance
must be given.
9675-2000200
UL 2703 certied for electric bonding and grounding

factory-installed module-mounting stainless steel screw
tested for use, also by
leading module manufacturers
Ballast stones
Polar Bear
190 mm x
400 mm x
90 mm
concrete
WASI SOLAR FLAT ROOF SYSTEM
POLAR BEAR

Art.No. / Figure
Article
Dimension
Variant /
Material
VPE
Description
Article
Dimension
Variant /
Material
VPE
Description
100
thread all the way to the head;

pursuant to DIn 933;
also adequate for
nearly all
further WAsI assembly rails
933-2-10 x 30
9675-200010704
9675-200010705
Art.No. / Figure
Wind deector
Aluminium, 69 inch
1754 mm x
275 mm
Wind deector
Aluminium, 73 inch
1854 mm x
275 mm
Aluminium
Deector 69 inch or 73 inch

adequate for
Polar Bear and Grizzly Bear
(1 = 2,54 cm)
Hexagonal
screw
10 mm x
30 mm
A2
A4
9345-2-10
9675-200010804
9675-200010805
Wind deectorr
G90 steel
galvanized, 69 inch
Wind deector
G90 steel
galvanized, 73 inch
1754 mm x
275 mm
1854 mm x
275 mm
G90
steel
galvanized
Deector 69 inch or 73 inch

adequate for
(1 = 2,54 cm)
Hexagonal nut
with serration
M10
A2
100
hexagonal nut with ange

and serration in
A2; M10;
tting for
DIn 933-2-10 x 30
Hexagonal nut
with serration
M6
A2
200
hexagonal nut with ange

and serration in
A2; M 6;
9345-2-6
9675-2000139
end plate for the deector

adequate for
1 end plate per
completed module rowe
222,6 mm x
38,1 mm
G90
steel
galvanized
end plate for the deector

adequate for
1 end plate per
completed module rowe
Aluminium
claw made of aluminium for

4 claws per module
222,6 mm x
38,1 mm
Aluminium
End plate Deector

G90 steel
galvanized
Claw
Standard
End plate Deector

Aluminium
9675-2000140
9675-5010005
Wagener & Simon

WASI GmbH & Co. KG
Emil-Wagener-Strae 1
D- 42289 Wuppertal
www.wasi-solar.de
Date: 05 / 2012

Wasi Polar Eng

Uploaded by

Copyright:

Available Formats

Wasi Polar Eng

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Wasi Polar Eng

Uploaded by

Copyright:

Available Formats

PV MOUNTING SYSTEM

We secure the sun

Hexagonal nut with serration 9345-2-6

Support Polar Bear (Aluminium

or G90 Steel galvanized, optionally

(Aluminium or G 90 Steel galvanized)

with roof protection pad)

Hexagonal nut with serration 9345-2-10

Hexagonal scew 933-2-10 x 30

(Aluminium or G90 Steel galvanized)

European Business Partner of WASI Solar

POLAR BEAR FR: TECHNICAL DATA

Fig.: Polar Bear FR Gen II 10 Grad

Flat roof (max slope 5 degrees)

160-180 modules per day (3-person crew)

Module Tilt Angle

10 12 degrees (depending on module width)

Longitudinal direction (on the short side)

Basic Wind Speed

up to 193 km/h (Zone 4)

Array Platform Load

approx. 14 and 39 kg/m (distributed onto the unit surface)

up to 18.3 m (custom upon request)

Aluminium or G90 Steel

WASI SOLAR FLAT ROOF SYSTEM

breakthrough is needed. A folding function for single modules

tems for at roofs that uses only 3 system components. Polar

simplies the module and roof maintenance - and thus helps

Bear is especially lightweight and can be quickly set up and

to keep the maintenance costs low.

3 - Polar Bear FR Gen II 10- all components

dissembled at low cost. The roof is ideally protected, no roof

universal, module-independent design

certied, location related ballast calculation of the system

pre-installed screws to assemble the wind deector

2 pieces per foot.

1 piece per support.

the concrete stones are usually not included in the delivery

UL 2703 certied for electric bonding and grounding

WASI SOLAR FLAT ROOF SYSTEM

3 - Polar Bear FR Gen II 10- all components

thread all the way to the head;

Deector 69 inch or 73 inch

Deector 69 inch or 73 inch

hexagonal nut with ange

hexagonal nut with ange

end plate for the deector

end plate for the deector

claw made of aluminium for

End plate Deector

End plate Deector

Wagener & Simon

You might also like