TDS - Masterflow 524

MASTERFLOW
524
High strength, non shrink cementitious
construction grout
Description
Typical applications
MASTERFLOW 524 is a ready to use product in powder

form, which requires only the on-site addition of water to
produce a non shrink grout of predictable performance.
Applications
MASTERFLOW 524 is formulated for use at plastic or
flowable consistency, and may be used with confidence for
bedding, grouting and void filling operations.
Advantages
Non shrink.
Adjustable consistency.
Proven and predictable performance.
High bond strength to steel and concrete.
Early strength development even at flowable
consistency.
Impermeable.
Packaging
MASTERFLOW 524 is supplied in 25kg bags.
Typical properties*
Water addition
Density
Flowable
Plastic
Flowable
Plastic
Free expansion:
Restrained expansion:
Compressive Strength N/mm ASTM C-109:
1 day
3 day
28 day
Flexural Strength N/mm BS 6319 Part 3:
28 day
Tensile Strength N/mm BS 6319 Part 7:
28 day
Water penetration DIN 1048 Part 5:
3.75 ltrs / 25 kg
3.40 ltrs / 25 kg
2230 kg / m
2350 kg / m
2-4%
0 - 0.4 %
Flowable
39.00
43.00
58.00
Flowable
6.95
Flowable
4.04
Nil
Application procedure
Preparation:
The surface onto which the grout is to be applied should be
scabbled to remove laitance and expose aggregate. Do not
use bush hammers or similar preparation equipment that
can crush the aggregate but leave it in place. The surface
must be free of oil, dust, dirt, paint, curing compounds or
other contaminants that could impair adhesion. Soak area
to be grouted to minimise absorption. Surfaces should be
damp but free of standing water. Particular attention should
be paid to bolt holes to ensure that these are water-free.
Use oil free compressed air to blow out bolt holes and
pockets as necessary.
Base plates, bolts, etc. must be clean and free of oil, grease
and paint. Set and align equipment. If shims are to be
removed after the grout has set, then lightly grease them for
easy removal.
Ensure formwork is secure and watertight to prevent
movement and leaking during the placing and curing of the
grout.
Mixing:
Damp down the inside of the grout mixer with water prior to
mixing the initial batch of MASTERFLOW 524. Ensure the
mixer is damp but free of standing water. Add the premeasured quantity of water. Slowly add the MASTERFLOW
When a very rapid set is required in areas subject to

chemical spillage or contamination, use epoxy grouts
MASTERFLOW 400 / 410.
524, mixing continuously. Mix for 3-5 minutes until a

smooth, uniform, lump free consistency is achieved.
Placing:
Place immediately after mixing, into the prepared area in
such a manner that the grout has the shortest distance to
flow. Pour the grout continuously maintaining a constant
hydrostatic head wherever possible.
MASTERFLOW grouts are suitable for use with most types
of pumping equipment.
Immediately after MASTERFLOW 524 grout is placed, cover
all exposed grout with clean wet hessian and keep moist
until grout surface is ready to be finished, or until final set.
Alternatively, consider the use of a curing membrane from
the MASTERKURE range.
Storage
For additional information on MASTERFLOW 524 grout or

other non-shrink grouting materials, contact your Degussa
representative.
Safety precautions
As with other products containing Portland cement, the
cementitious material in MASTERFLOW 524 grout may
cause irritation. In case of contact with eyes, immediately
flush with plenty of water for at least 15 minutes. Call a
physician. In case of contact with skin, wash skin
thoroughly.
Note
Store out of direct sunlight, clear of the ground on pallets

protected from rainfall. Avoid excessive compaction.
Storage life is approximately 18 months when stored in ideal
conditions in original sealed bags.
Precautions
The temperature of both the grout and elements coming into
contact with the grout should be in the range of +5C to
+35C. Do not use water in an amount or at a temperature
that will produce a consistency more than flowable or cause
mixed grout to bleed or segregate.
MASTERFLOW 524 should be laid at a minimum thickness
of 10mm and to a maximum depth of 80mm.
Field service, where provided, does not constitute

supervisory responsibility. For additional information contact
your local Degussa representative.
Degussa reserves the right to have the true cause of any
difficulty determined by accepted test methods.
Quality and care

All products originating from Degussas Dubai, UAE facility
are manufactured under a management system
independently certified to conform to the requirements of the
quality, environmental and occupational health & safety
standards ISO 9001, ISO 14001 and OHSAS 18001.
05/94 Degussa-UAE revised 02/2004
For applications above 80mm consider the use of

MASTERFLOW 980 T. For applications below 10mm
consult Degussa Technical Services Department for advice.
DO NOT OVERWORK AND AVOID USING MECHANICAL
VIBRATION.
REQUEST AND REFER TO RECOMMENDED

INSTALLATION PROCEDURES FOR
MASTERFLOW GROUTS PRIOR TO USE
* Properties listed are only for guidance and are not a guarantee of
performance.
UNDER NO CIRCUMSTANCES SHOULD MASTERFLOW

524 BE RETEMPERED BY THE LATER ADDITION OF
WATER.
It is essential that a mechanically powered grout mixer is
used to obtain the optimum properties. A slow speed drill
and mixing paddle may be used for single bag batches only.
Yield / consumption
12.9ltr / 25kg bag at flowable consistency.
78 x 25kg bags / m.
Note:
For precision grouting of heavy machinery use
MASTERFLOW 928 T or in critical operating conditions
MASTERFLOW 885.
Degussa Construction Chemicals UAE LLC
P.O. Box 37127, Dubai, UAE
Tel: +971 4 8851000
Fax: +971 4 8851002
www.degussa-cc.ae
e-mail: marketingcc.mideast@degussa.com
Whilst any information contained herein is true, accurate and

represents our best knowledge and experience, no warranty is given or
implied with any recommendations made by us, our representatives or
distributors, as the conditions of use and the competence of any labour
involved in the application are beyond our control.
Certificate No.
963680
As all Degussa technical datasheets are updated on a regular basis it is the user's responsibility to obtain the most recent issue.
Certificate No.
945787
Certificate No.
772556

TDS - Masterflow 524

Uploaded by

Copyright:

Available Formats

TDS - Masterflow 524

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TDS - Masterflow 524

Uploaded by

Copyright:

Available Formats

MASTERFLOW

MASTERFLOW 524 is a ready to use product in powder

When a very rapid set is required in areas subject to

524, mixing continuously. Mix for 3-5 minutes until a

For additional information on MASTERFLOW 524 grout or

Store out of direct sunlight, clear of the ground on pallets

Field service, where provided, does not constitute

Quality and care

For applications above 80mm consider the use of

REQUEST AND REFER TO RECOMMENDED

UNDER NO CIRCUMSTANCES SHOULD MASTERFLOW

Fax: +971 4 8851002

Whilst any information contained herein is true, accurate and

You might also like