Press. Regulator

Industrial Regulators
The industry standard for pressure regulators and flow control products.
Conversion Tables
TEMPERATURE CONVERSION FORMULAS
From Fahrenheit (F) to Celsius (C)
(F - 32) x 5/9
From Fahrenheit (F) to Kelvin (K)
(F + 459.67) / 1.8
From Celsius (C) to Fahrenheit (F)
(C x 9/5) + 32
From Celsius (C) to Kelvin (K)
(C + 273.15)
From Kelvin (K) to Fahrenheit (F)
(1.8 x K) - 459.67
From Kelvin (K) to Celsius (C)
(K - 273.15)
PRESSURE CONVERSION
FROM
TO
bar
bar
kPa
mm Hg (0C)
mm H2O (4C)
kg/cm2
in H2O (4C)
psi
in Hg (32C)
100
750.064
10197.443
1.02
401.474
14.504
29.53
kPa
0.01
7.501
101.974
0.01
4.015
0.145
0.295
mm Hg (0C)
0.001
0.133
13.595
0.001
0.535
0.019
0.039
mm H2O (4C)
0.0001
0.01
0.074
0.0001
0.039
0.001
0.003
kg/cm2
0.981
98.067
735.561
10000.275
393.712
14.223
28.959
in H2O (4C)
0.002
0.249
1.868
25.4
0.003
0.036
0.074
psi
0.069
6.895
51.715
703.089
0.07
27.681
2.036
in Hg (32C)
0.034
3.386
25.4
345.324
0.035
13.595
0.491
VOLUMETRIC GAS FLOW CONVERSION

FROM
TO
3
Nm /hr
SCFH
SCFM
in3/min
Nliters/min
Nm3/hr
35.31
0.59
1,017
16.67
SCFH
0.03
0.02
28.8
0.47
SCFM
1.7
60
1,728
28.32
in3/min
0.001
0.03
0.0006
0.02
Nliters/min
0.06
2.12
0.04
61.02
VOLUMETRIC LIQUID FLOW CONVERSION

FROM
TO
liters/sec
liters/min
m3/h
ft3/min
ft3/hr
US
gallon/min
UK
gallon/min
barrels
(petroleum)/min
liters/sec
60
3.6
2.12
127.1
15.85
13.2
0.38
liters/min
0.02
0.06
0.04
2.12
0.26
0.22
0.01
m /h
0.28
16.67
0.59
35.31
4.4
3.67
0.1
ft3/min
0.47
28.32
1.7
60
7.48
6.23
0.18
ft3/hr
0.01
0.47
0.03
0.02
0.12
0.1
0.003
US gal/min
0.06
3.79
0.23
0.13
8.02
0.83
0.02
UK gal/min
0.08
4.55
0.27
0.16
9.63
1.2
0.03
barrels (petroleum)/min
2.65
159
9.54
5.62
336.9
42
34.97
Table of Contents
INTRODUCTION
Introduction to Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Industrial Regulator Quick Selection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7
Fisher Industrial Regulator Plant Utility Application Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 9
Regulators
Air
Liquids
MR95 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Type MR105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MR98 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Type MR108 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
67C Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Type 92W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1301F/1301G Series . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Type 63EG-98HM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
67D Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MR95 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
627 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MR98 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
63EG Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Type LR125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Steam
Type LR128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Type 92B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Type 1098-EGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Type 92S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Type 75A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Type SR5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Process Gas
MR95 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Type 1098-EGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Type 92C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
MR95 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MR98 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
MR98 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Tank Blanketing/Vapor Recovery
T205 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
T205 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
T208 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Type T205B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
T205VB Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
T208 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Fuel Gas
Type Y692 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Type 310A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Type Y693 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Type EZR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Type ACE95 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Y600A Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Type 1190 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Type 1098-EGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Type 1290 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
EZH and EZHSO Series . . . . . . . . . . . . . . . . . . . . . . . . 21

Type 99 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
133 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Regulator Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 -23

3
Pressure Reducing Regulators

Direct-Operated
Pilot-Operated
Regulators are self-contained, control devices which use

energy from the controlled system to operate whereas
control valves require external power sources, transmitting
instruments, and control instruments.
Pilot-Operated Regulators
MAIN
REGULATOR
pilot
Regulator

A pressure reducing regulator maintains a desired outlet
pressure while providing the required fluid flow to satisfy
a downstream demand. The pressure which the regulator
maintains is the outlet pressure setting (setpoint) of
theregulator.
Pressure Reducing Regulator Type

inlet pressure
outlet pressure
ATMOSPHERIC PRESSURE
loading pressure
The two main types of regulators:

1. Direct-Operated
2. Pilot-Operated
Figure 2. Pilot-Operated Regulator

SPRING
DIAPhRagm
valve
inlet pressure
outlet pressure
Figure 1. Direct-Operated Regulator
Direct-Operated Regulators
Direct-Operated regulators are the simplest style of the
regulators. At low set pressures, typically below 1 psig /
0.07 bar, they can have very accurate (1%) control. At
high control pressures, up to 500 psig / 34.5 bar, 10% to
20% control is typical.
In operation, a direct-operated, pressure reducing
regulator senses the downstream pressure through either
internal pressure registration or external control line. This
downstream pressure opposes a spring which moves the
diaphragm and valve plug to change the size of the flow
path through the regulator.
Direct-operated regulators have many commercial and
residential uses. Typical applications include industrial,
commercial, and domestic gas service or instrument air.
4
Pilot-Operated regulators are preferred for high flow rates

or where precise pressure control is required. A popular
type of pilot-operated system uses two-path control.
In two-path control, the main valve diaphragm responds
quickly to downstream pressure changes, causing an
immediate correction in the main valve plug position.
At the same time, the pilot diaphragm diverts some of the
reduced inlet pressure to the other side of the main valve
diaphragm to control the final positioning of the main
valve plug. Two-path control results in fast response and
accurate control.
Pressure Reducing Regulator Selection

The majority of applications require a pressure reducing
regulator. Assuming the application calls for a pressure
reducing regulator. The following parameters must
be determined:
Outlet pressure to be controlled
Inlet pressure to the regulator
Capacity required
Shut-off capability required
Process fluid
Process fluid temperature
Accuracy required
Pipe size required
End connection style
Material requirements
Control line needed
Overpressure protection
Relief Valve / Backpressure Regulator

Relief Valve
Backpressure Regulator
Relief Valves and Backpressure Regulators

A pressure relief valve is a control device that opens to relieve
fluid to atmosphere during an overpressure occurrence. A
backpressure regulator is a control device that maintains a
constant upstream pressure throughout a given flow range.
pilot
main relief
valve
restriction
Control
line
pilot
exhaust
Relief Valve Types

Relief valves are available in four general types: pop type,
direct-operated, pilot-operated, and internal relief valves.
main regulator
Exhaust
flow
inlet pressure
atmospheric pressure
Direct-Operated Relief Valves

System pressure is referenced under a diaphragm and
opposed by a spring. As system pressure increases past the
setpoint, the relief valve opens which allows fluid to escape
and protects the system. The increase in pressure above
the relief setpoint that is required to produce more flow
through the relief valve is referred to as pressure buildup.
spring
diaphragm
loading pressure
exhaust
Figure 4. Pilot-Operated Relief Valve
Pilot-operated relief valves are used in applications

requiring high-capacity and low-pressure buildup.
Internal Relief
The regulator shown in Figure 5 includes an internal relief
valve. The relief valve has a measuring element (the main
regulator diaphragm), a loading element (a light spring),
and a restricting element (a valve seat and disk).
opened internal relief
valve
large opening for relief
vent
flow
system pressure
closed restriction
lower-pressure system
(usually atmosphere)
Figure 3. Direct-Operated Relief Valve
Direct-Operated relief valves are commonly used in industry

to protect industrial furnaces and other equipment.
Pilot-Operated Relief Valves

In normal operation, when system pressure is below
setpoint of the relief valve, the pilot remains closed.
This allows loading pressure to register on top of the
main relief valve diaphragm. Loading pressure on top
of the diaphragm is opposed by an equal pressure (inlet
pressure) on the bottom side of the diaphragm. With
little or no pressure differential across the diaphragm, the
spring keeps the valve seated. When the system pressure
increases past the setpoint, the pilot opens and exhausts
the loading pressure from the top of the relief valve main
diaphragm which allows the main valve to open.
inlet pressure
outlet pressure
Figure 5. Internal Relief
The relief valve assembly is located in the center of

the regulator diaphragm. Internal relief is often used
in industrial applications where atmospheric exhaust is
acceptable, and low buildup is not required.
Backpressure Regulator Selection

Backpressure regulators control the inlet pressure rather
than the outlet pressure. The selection criteria for the
backpressure regulator is the same as for a pressure
reducing regulator.
5
Industrial Regulators Selection Table
OUTLET PRESSURE
RANGE*, psig / bar
Ste
am
Ta
nk
B
Liq lank
eti
uid
ng
Pr
oc
es
sG
Fu
a
el
Ga s
s
Air
Pressure Reducing Regulator
TYPE OR OPERATION
SERIES
METHOD
0-125 / 0-8.6
0-150 / 0-10.3
0-150 / 0-10.3
10-500 / 0.69-34.5
67C
67CS
67D
1301
Direct
Direct
Direct
Direct
2-400 / 0.14-27.6
MR95
Direct
2-135 / 0.14-9.3
SR5
Direct
2-250 / 0.14-17.2
92B
Pilot
2-250 / 0.14-17.2
92S
Pilot
5-250 / 0.34-17.2
92C
Pilot
20-80 / 1.4-5.5
75A
Direct
2-250 / 0.14-17.2
92W
Pilot
BODY SIZE, NPS

1/4
1/4
1/2
1/4
REFERENCES
MAXIMUM MAXIMUM
INLET
FLOW
PRESSURE, CAPACITY, PAGE BULLETIN NO.
psig / bar SCFH / Nm3/h
250 / 17.2
400 / 27.6
400 / 27.6
6000 / 414
4350 / 117
4350 / 117
20,900 / 560
4500 / 121
17,000 lbs/h /
1/4 to 2
1000 / 68.9
7600 kg/h
6820 lbs/h /
1/2 to 3
210 / 14.5
3096 kg/h
42,400 lbs/h /
1, 1-1/2, 2, 3, and 4
300 / 20.7
19,234 kg/h
45,100 lbs/h /
1 to 6 x 4
300 / 20.7
20,457 kg/h
3600 lbs/h /
1/2, 3/4, and 1
300 / 20.7
1633 kg/h
260 gpm /
1/2 to 2-1/2
200 / 13.8
984 l/min
960 gpm /
1 to 4
300 / 20.7
3720 l/min
3/4, 1, and 2
2000 / 138 162,000 / 4342
82 gpm /
3/4, 1, and 2
900 / 62.1
310 l/min
1650 gpm /
1, 2, 3, and 4
400 / 27.6
6240 l/min
11,934 gpm /
1 to 12 x 6
400 / 27.6
45,170 l/min
1, 2, 3, 4, 6, 8 x 6, and
2,811,000 /
400 / 27.6
12 x 6
75,335
2
1000 / 69.0 265,000 / 7102
2, 3, and 4
10 / 0.69
49,000 / 1313
3/4 and 1
200 / 13.8 12,919 / 346.2
5-500 / 0.34-34.5
627
Direct
10-500 / 0.69-34.5
627W
Direct
5 to 300 / 0.34 to 20.7
MR105
Direct
4"wc-300 / 10 mbar-20.7
1098-EGR
Pilot
0.25"wc-7 / 0.6 mbar-0.48
1190
Pilot
2"wc-100 / 5 mbar-6.9
2"wc-5 / 5 mbar-0.34
1"wc-7 / 2 mbar-0.48
99
66
T205
Pilot
Direct
Direct
1"w.c.-7 psig / 2 mbar-0.48 bar
T205B
Direct
3/4 and 1
200 / 13.8
1"wc-10 / 2 mbar-0.69
0.5"wc-10 / 1 mbar-0.69
2"wc-60 / 5 mbar-4.1
Y692
Y693
133
Direct
Direct
Direct
1-1/2 and 2
1-1/2 and 2
2
150 / 10.3
150 / 10.3
150 / 10.3
-5"wc-1.5 / -12 mbar-0.10
ACE95
Pilot
3/4, 1, and 1 x 2
200 / 13.8
-5"wc-1.5 / -12 mbar-0.10
ACE95jr
Direct
1/2, 1 x 1/2, and 1
200 / 13.8
-5"wc-1.5 / -12 mbar-0.10
ACE95sr
Pilot
200 / 13.8
Pad: 0.5"wc-2.2 / 1 mbar-0.15

Depad: 4"wc-2 / 10 mbar-0.14
ACE97
Pilot
Pad: 1/2, 1, and 2 and

Depad: 1-4
200 / 13.8
6"wc-1000 / 15 mbar-69.0
EZR
Pilot
1 to 8
1500 / 103
3.5"wc-60 / 9 mbar-4.1
299H
Pilot
1-1/4, 1-1/2, and 2
175 / 12.1
10
11
11
71.1:67C
71.1:67C
71.1:67D
71.1:1301
13
71.1: MR95
13
71:1:SR5
12
71.2:92B
12
71.2:92S
13
71.2:92C
17
71.1:75A
16
71.2:92W
11
71.1:627
71.1:627W
16
71.1:MR105
18
71.2:1098-EGR
15
74.1:1190
21
14
71.2:99
74.1:T205
18,568 / 498
14
74.1:T205B
19,820 / 531
26,700 / 716
170,000 / 4556
499,600 /
13,390
3330 / 89.2
499,600 /
13,390
Pad: 499,600 /
13,389
De-pad:
106,200 / 2846
26,138,000 /
700,498
108,120 / 2898
15
15
21
74.1:Y692
74.1:Y693
71.1:133
15
74.1:ACE95
71.1:66
74.1:ACE95jr
74.1:ACE95
74.3:ACE97
20
71.2:EZR
71.2:299H
Selection Table
OUTLET PRESSURE
RANGE*, psig / bar
Ste
am
Ta
nk
B
Liq lank
eti
uid
ng
Pr
oc
es
sG
Fu
a
el
Ga s
s
Air
Backpressure Regulators
Relief Valve
TYPE OR OPERATION
SERIES
METHOD
BODY SIZE, NPS
REFERENCES
MAXIMUM MAXIMUM
INLET
FLOW
PRESSURE, CAPACITY, PAGE BULLETIN NO.
psig / bar SCFH / Nm3/h
15-150 / 1-10.3
LR125
Pilot
1, 2, 3, and 4
300 / 20.7
35-375 / 2.4- 25.9
LR128
Pilot
1, 2, 3, and 4
450 / 31.0
4"w.c. to 7 psig /
10 mbar to 0.48 bar
Y600A
Direct
3/4 and 1
150 / 10.3
2"wc-10 / 5 mbar-0.69
CS800
Direct
1-1/4 ,1-1/2, and 2
2052 gpm /
7769 l/min
3368 gpm /
12,748 l/min
17
71.2:LR125
17
71.4:LR128
6660 / 178
20
71.1:Y600A
125 / 8.6
36,270 / 974
71.1:CS800
21
71.2:EZH and
EZHSO
14.5-1160 / 1.0-80.0
EZH
Pilot
1 to 4
1500 / 103
13,833,000 /
370,724
3-500 / 0.21-34.5
630
Direct
1 and 2
1500 / 103
96,000 / 2573
71.1:630
10-700 / 0.69-48.3
310A
Pilot
1 to 4 x 6
1500 / 103
21,170,000 /
567,356
20
71.2:310A
5"wc-75 / 12 mbar-5.2
289
Direct
1/4, 3/4, 1, and 2
100 / 6.9
120,000 / 3216
71.4:289
3-125 / 0.21-8.6
1808
Pilot
150 / 10.3
298,000 / 7986
71.4:1808
15-375 / 1.0-25.9
63EG-98HM
Pilot
2 to 6 and 8 x 6
450 / 31.0
4900 gpm /
18,547 l/min
16
71.4:63EG-98HM
2-375 / 0.14-25.9
MR98
Direct
1/4 to 2
400 / 27.6
300 gpm /
1150 l/min
17
71.4: MR98
5 to 300 / 0.34 to 20.7
MR108
Direct
1, 2, 3, and 4
400 / 27.6
1460 gpm /
5530 l/min
16
71.4:MR108
2-125 / 0.14-8.6
SR8
Direct
1/2 to 3
210 / 14.5
5460 lbs/h /
2479 kg/h
71.4:SR8
10-400 / 0.69-27.6
63EG
Pilot
1 to 6 and 8 x 6
400 / 27.6
8,795,000 /
235,706
11
71.4:63EG
2"wc-5 / 5 mbar-0.34
66R
Direct
2, 3, and 4
8 / 0.55
115,000 / 3082
71.4:66
2"wc-7 / 5 mbar-0.48
T208
Direct
3/4 and 1
75 / 5.2
2286 / 61.3
14
74.2:T208
2"wc-7 / 5 mbar-0.48
Y696
Direct
1-1/2 and 2
15 / 1.0
13,100 / 351
74.2:Y696
1290
Pilot
1, 2, 3, 4, 6, 8 x 6, and
12 x 6
12.5 / 0.86
327,400 / 8774
15
74.2:1290
0.5"wc-7 / 1 mbar-0.48
3-60 / 0.21-4.1
119
Direct
3/4, 1, and 1-1/4
150 / 10.3
----
71.1:119
3-150 / 0.21-10.3
167D
Direct
1/4 and 1/2
400 / 27.6
----
71.7:167D
14-125 / 0.97-8.6
167DA
Direct
1/4 and 1/2
125 / 8.6
----
71.7:167D
2-150 / 0.14-10.3
168
Direct
1/4
150 / 10.3
----
71.7:168
0-5 / 0-0.35 vacuum
T205VB
Direct
3/4 and 1
200 / 13.8
2468 / 66
19
71.3:T205VB
1"wc-3 / 2 mbar-0.21
Y692VB
Direct
1-1/2 and 2
30 / 2.1
2500 / 67
71.3:Y692VB
0-12.8 / 0-0.88
T208VR
Direct
3/4 and 1
Full Vacuum
1345 / 36.0
71.3:T208VR
1"wc-3 / 2 mbar-0.21
Y696VR
Direct
1-1/2 and 2
Full Vacuum
6953 / 186
71.3:Y696VR
*Inlet/Outlet Pressure Range and Maximum Inlet Pressure are indicated as psig/bar or inches w.c./mbar.
This catalog is a brief overview of the Fisher product line.

Please visit www.fisherregulators.com to view the entire Fisher offering.
For Plant Utility Applications
Regulator
Industrial
Gas Plant
Control Valve
Control Line
Fuel Gas
Oxygen
Pneumatic Air
Hydrogen
Steam
Nitrogen
Process Liquids
Water
Lube Oil
Water
Tower
MR95
LR128
Pump
MR95
Process
Storage
167DA
MR105
easy-e
67DFR
Compressor
MR98
Feedwater Tank
MR95
Safety Shower/
Eyewash Station
92C
63EG98HM
1098
EGR
66
T205
ACE 95
1290
T208VR
Instrument Purge
Vacuum
Regulator
Glove
Box
Vacuum
Pump
Vapor
Recovery
Vacuum
Breaker
easy-e
Process
Reactor
Process
Reactor
Tank Blanket
T205VB
1098
EGR
Packaging
Station
67DFR
Batch
Reactor
Heat Exchanger
easy-e
92B
92S
Boiler
Air
Compact
Rugged Construction
Integral Filters
Wide Selection
Built to Last
Time-Proven Design
Pressure Reducing
MR95 Series
Body Size
NPS 1/4, 1/2, 3/4, 1, 1-1/2, and 2 /

DN 15, 20, 25, 40, and 50
Outlet Pressure Range 2 to 400 psig / 0.14 to 27.6 bar

Maximum Inlet
1000 psig / 68.9 bar
Pressure
Maximum Capacity 510,000 SCFH / 13,668 Nm3/h
Operation Method Direct-Operated
Manufacturing and process plants use

compressed air as a power supply for many
devices within the plant. Plant air, also called
shop air, is used for cooling and as a power
source for pneumatic tools, sand blasters,
sprayers, conveyors, robotics, and other
mechanical tools. Instrument air is used to
power instruments, such as controllers,
positioners, switching valves, panel loaders,
and volume boosters.
Body Material
Cast Iron, Steel, Stainless Steel,

Hastelloy C, and Monel
Bulletin No. 71.1:MR95

The MR95 Series is a versatile, compact, high-capacity direct-operated regulator capable
of solving the toughest pressure control applications. Typical applications include
instrument air supply for large actuators, test fixtures, and general pneumatic supply. The
regulator is available with differential pressure control, high temperature, and
high-pressure optional constructions.
Pressure Reducing
67C Series
Body Size NPS 1/4
Outlet Pressure Range 0 to 150 psig / 0 to 10.3 bar
Maximum Inlet
400 psig / 27.6 bar
Pressure
Maximum Capacity 4350 SCFH / 117 Nm3/h
Plant air or shop air runs from compressor

throughout the plant. Pressure reducing
regulators control the pressure to devices at
each point of use of the air line.
Instrument air can come from the plant air line,

Body Material Aluminum and Stainless Steel
Bulletin No. 71.1:67C
The 67C Series is a compact, high accuracy instrument air regulator designed for use
with todays digital valve controllers. The unit is available with a 5 or 40 micron filter for
protection of the instrument being supplied. The Smart Bleed option and leak proof
internal relief minimize loss of supply air improving system integrity. Other options
include outlet gauge, high and low temperature, and panel mounting.
or they may be separate air lines throughout

the plant. In either case, the air supplied to the
instruments must be cleaned and dried before
it enters the instruments. Filters and dryers
remove dust, moisture, and other debris from
the air.
Relief/Backpressure
MR98 Series
NPS 1/4, 1/2, 3/4, 1, 1-1/2, and 2 /
DN 15, 20, 25, 40, and 50
2 to 375 psig /
Relief Pressure Range
0.14 to 25.9 bar
Maximum Inlet
400 psig / 27.6 bar
Pressure
Body Size
Maximum Capacity 206,000 SCFH / 5510 Nm3/h

Body Material


The MR98 Series is used in a variety of process gas backpressure and relief applications
including corrosive gases and cryogenic applications. The unit is available with a remote
control line, differential pressure control and high-pressure optional constructions.
10
Pressure Reducing
Pressure Reducing
1301 Series
627 Series
Body Size NPS 1/4

Maximum Inlet Pressure 6000 psig / 414 bar
Maximum Capacity 4500 SCFH / 121 Nm3/h
Body Material Brass and Stainless Steel
Bulletin No. 71.1:1301
The 1301 Series regulators are high-pressure regulators designed to reduce supply
pressure of instrument air supply regulators and pilots. The units have options for spring
case with tapped vents and adjusting screw closing cap.
Body Size
NPS 3/4, 1, and 2 /

DN 20, 25, and 50

Body Material
Ductile Iron, Steel, and

Stainless Steel

The 627 Series direct-operated pressure reducing regulators are for low and
high-pressure systems. Typical air applications include high-capacity air supply to large
valve actuators.
Pressure Reducing
Relief/Backpressure
67D Series
63EG Series
Body Size NPS 1/2 / DN 15

Maximum Inlet Pressure 400 psig / 27.6 bar
Body Material Aluminum and Stainless Steel
Bulletin No. 71.1:67D
The 67D Series regulators are typically used to deliver constant reduced pressure of
gaseous fluids to pilot-operated controllers and other pneumatic instrumentation.
NPS 1, 2, 3, 4, 6, and 8 x 6 /
Body Size DN 25, 50, 80, 100, 150, and
200 x 150
Outlet Pressure 10 to 400 psig /
Range 0.69 to 27.6 bar
Maximum Inlet
400 psig / 27.6 bar
Pressure
8,795,000 SCFH /
Maximum Capacity
235,706 Nm3/h
Operation Method Pilot-Operated
Body Material
Cast Iron, Steel, and

Stainless Steel
Bulletin No. 71.4:63EG

The 63EG Series is a compact, fast response, high accuracy backpressure / relief valve
which is suitable for gas or liquid service. The valve's design allows easy maintenance and
is available with noise reducing trim.
11
Steam
High Turndown
Rugged Construction
Noise Reduction
Low Maintenance
Accurate
Reliable
Long Service Life
Steam is used throughout industries for
process and space heating. Within the process
industries, steam is used in oil refineries; pulp
and paper mills; chemical production, such
as ethylene and ammonia; food and grain
processing; and textiles.
Refineries and chemical plants use steam tracing
to reduce pumping costs of viscous material
and prevent freezing of process piping. Steam is
used for heat exchangers and reactors to assist
or create process chemical or thermal reactions.
Paper mills utilize major steam generation
systems to generate power and to dry paper
products. Steam is widely used for district
energy systems found in major municipalities
and central plants of universities and hospitals.
Pressure Reducing
Type 92B
NPS 1, 1-1/2, 2, 3, and 4 /
DN 25, 40, 50, 80, and 100
2 to 250 psig /
Outlet Pressure Range
0.14 to 17.2 bar
Maximum Inlet
300 psig / 20.7 bar
Pressure
Maximum Temp
600F / 316C*
Capacity
42,400 lbs/h /
Maximum Capacity
19,234 kg/h
Body Size

Body Material

Stainless Steel
Bulletin No. 71.2:92B

The Type 92B regulator is ideal for use as a main Pressure Reducing Valve in industrial
process heating applications such as heat exchangers, evaporators, digesters, and
reactors. Commercial applications include district energy systems and hot water
heatexchangers.
Pressure Reducing
Type 92S
NPS 1, 1-1/2, 2, 2-1/2, 3, 4, and
Body Size 6 4 / DN 25, 40, 50, 65, 80,
100, and 150 x 100
Maximum Inlet
300 psig / 20.7 bar
Pressure
Maximum Temp
650F / 343C*
Capacity
Maximum
45,100 lbs/h / 20,457 kg/h
Capacity
Operation
Pilot-Operated
Method
Body Material
Stainless Steel
Bulletin No. 71.2:92S
The Type 92S regulator is piston actuated for high cycle steam service with hardened trim
for improved durability. This valve should be used with clear, dry, or superheated steam.
Noise reduction trim is available.
To minimize piping cost, steam is generated

and distributed at much higher pressures and
temperatures than required by the process
load. Fisher regulators are utilized in these
applications to reduce the steam pressure to a
usable level and to accurately maintain process
fluid temperatures.
*
Maximum temperature limitation may vary according to body and construction materials.
Please refer to the product Bulletin or local Sales Office for further information.
12
Pressure Reducing
Pressure Reducing
Type SR5
Type 92C
NPS 1/2, 3/4, 1, 1-1/2 x 1, 1-1/2,

Body Size 2, and 3 / DN 15,20, 25, 40 x 25,
40, 50, and 80
Maximum Temp
400F / 204C*
Capacity
Maximum Capacity 6820 lbs/h / 3096 kg/h
Body Material
316L Stainless Steel,

20 in / 0.5 m Ra
Bulletin No. 71.1:SR5

The Type SR5 regulator is a compact, large capacity, direct-operated pressure reducing
regulator. It is designed for use in applications where a sanitary design is essential, such as
pharmaceutical, biotech, or food and beverage industries. A backpressure regulator is also
available in Type SR8.
NPS 1/2, 3/4, and 1 /

DN 15, 20, and 25
5 to 250 psig /
0.34 to 17.2 bar
Body Size

Maximum Temp Capacity 650F / 343C*
Body Material
Bulletin No. 71.2:92C

The Type 92C regulator is an economical cast iron, steel, or stainless steel pilot-operated
pressure reducing used in steam, liquid, or hot air service. Its compact design and
high-capacity make it ideal for packaged skid systems.
Pressure Reducing
Relief/Backpressure
MR95 Series
MR98 Series
NPS 1/4, 1/2, 3/4, 1, 1-1/2, and 2 /

Body Size
DN 15, 20, 25, 40, and 50
2 to 400 psig /
0.14 to 27.6 bar
Maximum Inlet
1000 psig / 68.9 bar
Pressure
Maximum Temp
650F / 343C*
Capacity
Maximum Capacity 17,000 lbs/h / 7600 kg/h
Body Material
Bulletin No. 71.1: MR95
of the toughest pressure control applications. Typical applications include fuel oil steam
atomization, superheated steam, boiler feed water, steam tracing, and sterilizers.

Stainless Steel
NPS 1/4, 1/2, 3/4, 1, 1-1/2, and 2 /

DN 15, 20, 25, 40, and 50
2 to 375 psig /
0.14 to 25.9 bar
Maximum Inlet
400 psig / 27.6 bar
Pressure
Maximum Temp
450F / 232C*
Capacity
Body Size

Body Material


The MR98 Series is used in a variety of steam backpressure/relief applications, such as
power generation, heating and cooling systems, and process system. The unit is available
with differential pressure control and high-pressure optional constructions.
*
Maximum temperature limitation may vary according to body and construction materials.
13
Tank Blanketing
Tank Blanketing
Fully Balanced System

High-Capacity
High Sensitivity
Tight Shutoff
Low Setpoints
In-line Maintenance
Broad Material Selection
T205 Series
NPS 3/4 and 1 /
DN 20 and 25
1-inch w.c. to 7 psig /
Control Pressure Range
2 mbar to 0.48 bar
Body Size

Flow up to
12,919 SCFH /
346.2 Nm3/h of Nitrogen

Body Material

Stainless Steel
Bulletin No. 74.1:T205
Tank Blanketing, or padding, is the process and

practice of covering the surface of a stored
commodity, usually a liquid, with an inert gas. If
that commodity is volatile or toxic, tank blanketing
can prevent it from harming workers, equipment,
and the environment. When the commodity is a
food or other substance, blanketing protects it from
oxidation or contamination through exposure to air
or moisture. In most cases, tank blanketing gas is
pure, dry nitrogen.
Blanketing can prevent liquids from vaporizing into
the atmosphere and can maintain the tanks vapor
space above a flammable or combustible liquid to
reduce potential ignition while pumping. It can
make up the volume of liquid displaced in or out of
a tank, or it can make up volume caused by thermal
changes of the tanks contents, preventing the
creation of a vacuum or excess operating pressure
that could damage the tank.
Vapor recovery systems are mainly used to prevent
toxic vapors from escaping into the atmosphere.
When adding liquid to the tank or when the outside
temperature rises, causing the vapor inside the tank
to expand, the vapor recovery system senses the
increase in tank pressure and vents the excessive
tank pressure to a vapor recovery system.
The T205 Series is a compact tank blanketing regulator ideal for blanketing small tanks
and vessels. The unit is easy to install and to maintain.
For larger applications, the Type Y692 is available in NPS 1-1/2 and 2 / DN 40 and 50 sizes.
Tank Blanketing
Type T205B
NPS 3/4 and 1 /
DN 20 and 25
2-inches w.c. to 7 psig /
5 mbar to 0.48 bar
Maximum Inlet
200 psig / 13.8 bar
Pressure
18,568 SCFH /
Flow up to
498 Nm3/h of Nitrogen
Body Size

Body Material

Stainless Steel
Bulletin No. 74.1:T205B

The Type T205B balanced tank blanketing regulator is a direct-operated regulator with
fully balanced plug design to reduce inlet pressure sensitivity and with a large diaphragm
to accurately control tank pressure at low pressure settings on tank blanketing systems.
Vapor Recovery
T208 Series
NPS 3/4 and 1
DN 20 and 25
5 mbar to 0.48 bar
Body Size

Flow up to
2286 SCFH /
61.3 Nm3/h of Nitrogen

Body Material

Stainless Steel
The T208 Series is ideal for small vapor recovery systems. The unit may also be utilized as
a backpressure or relief valve. A larger NPS 1-1/2 and 2 DN 40 and 50 units are available in
the Type Y696.
14
Tank Blanketing
Tank Blanketing
Type Y692
Type 1190
NPS 1-1/2 and 2 /

Body Size
DN 40 and 50
2 mbar to 0.69 bar
Maximum Inlet
150 psig / 10.3 bar
Pressure
Body Orientation In-line or Angle
Flow up to
19,820 SCFH /

Body Material
Cast Iron, WCC Steel, and

Stainless Steel
Bulletin No. 74.1:Y692

The Type Y692 is a direct-operated regulator used for accurate pressure control on very
low-pressure blanketing systems. The downstream pressure is sensed directly by the
diaphragm through the pitot tube providing quick response. Large diaphragm areas
provide more precise control even at low-pressure settings and the pilot tube also creates
a dynamic boost that helps provide greater capacity.
NPS 1, 2, 3, 4, 6, 8 x 6, and 12 x 6 /
Body Size DN 25, 50, 80, 100, 150,
200 x 150, and 300 x 150
Control Pressure 0.25-inch w.c. to 7 psig /
Range 0.6 mbar to 0.48 bar
Maximum Inlet
400 psig / 27.6 bar
Pressure
2,811,000 SCFH /
Flow up to
75,335 Nm3/h of Nitrogen
Operation
Pilot-Operated
Method
Body Material
Stainless Steel
The Type 1190 provides very accurate pressure control on low-pressure blanketing
systems. The regulator helps to control emissions and provides protection against any
contamination from atmospheric conditions.
Tank Blanketing
Vapor Recovery
Type Y693
Type 1290
NPS 1-1/2 and 2 /

Body Size
DN 40 and 50
0.5-inch w.c. to 10 psig /
1 mbar to 0.69 bar
Flow up to
26,700 SCFH /

Body Material

Stainless Steel
Bulletin No. 74.1:Y693

The Type Y693 utilizes a balanced trim design and large diaphragm area to provide
the accuracy of a pilot-operated regulator in a direct-operated design. The design also
provides minimal hysteresis and low inlet pressure sensitivity.
NPS 1, 2, 3, 4, 6, 8 x 6, 12 x 6 /
Body Size DN 25, 50, 80, 100, 150,
200 x 150, and 300 x 150
Control Pressure 0.5-inch w.c. to 7 psig /
Range 1 mbar to 0.48 bar
Maximum Inlet
12.5 psig / 0.86 bar
Pressure
327,400 SCFH /
Flow up to
Operation
Pilot-Operated
Method
Body Material
Stainless Steel
The Type 1290 vapor recovery valve is a very accurate high-capacity which monitors
the tank vapor pressure and opens when the tank pressure increases above the desired
setpoint. The unit is ideal for use with vapor recovery systems because it is not affected by
changes in pressure of the recovery system.
Tank Blanketing
ACE95 Series
NPS 3/4, 1, 1 x 2, and 2 /
DN20, 25, 25 x 50, and 50
Control Pressure -5-inch w.c. to 1.5 psig /
Range -12 mbar to 0.10 bar
Maximum Inlet
200 psig / 13.8 bar
Pressure
Body Size
Body Orientation In-line or Angle

Flow up to
499,600 SCFH /
13,390 Nm3/h of Nitrogen

Body Material Stainless Steel
Bulletin No. 74.1:ACE95
The ACE95 Series is ideal for accurate pressure control on low-pressure blanketing
systems. The oversized actuator offers high sensitivity to changes in tank pressure and
high accuracy to pressure control. The ACE97 Series utilizes a single pilot to control both
the tank blanketing and vapor recovery minimizing the issues with overlapping setpoints.
15
Liquid
Highest Quality Construction
Best Product Selection
Large Turndown Ratios
Excellent Fluid Capability
Quick and Easy Maintenance
Application Experience
Pressure Reducing
Type MR105
NPS 1, 2, 3, and 4 /
DN 25, 50, 80, and 100
5 to 300 psig /
0.34 to 20.7 bar
Body Size

Maximum Capacity 1650 gpm / 6240 l/min
Any substance that is capable of flowing or of

being poured is known as a liquid. One of the
most common liquids that we come in contact
with on a daily basis is water. Other liquids
include detergents, paints, aqueous chemicals,
fuels, and oil.
Liquids differ from gases as they are
incompressible and viscous. Because of these
characteristics, special consideration must be
given when selecting a regulator. All regulator
parts that touch the fluid must be compatible
with the fluid. The regulator design may require
modifications or special materials.
Body Material

Stainless Steel
Maximum Temp Capability 250F / 121C*

The Type MR105 is fast-response, high-capacity, direct-operated multi-purpose regulator
designed to handle different applications and flow media. It is available in linear and quick
opening trim cages and is designed to meet API 614 as required by lube oil manufacturers.
Relief/Backpressure
Type MR108
Body Size
NPS 1, 2, 3, and 4 /
DN 25, 50, 80, and 100
Backpressure Control
5 to 300 psig / 0.34 to 20.7 bar
Range
Body Material

Stainless Steel
Maximum Temp Capability 250F / 121C*

The Type MR108 regulators are direct-operated, backpressure, high-capacity, multipurpose regulators. It provides a simple, reliable, and economical backpressure control
in multi-purpose applications suitable for different flow media including liquid, air, and
gas. Applications include lube oil systems and any application where speed of response is
critical, minimum differential pressure is a requirement, or fluid is not free of impurities.
Pressure Reducing
Relief/Backpressure
Type 92W
Type 63EG-98HM
Body Size
NPS 1, 1-1/2, 2, 2-1/2, 3, and 4 /

DN 25, 40, 50, 65, 80, and 100
2 to 250 psig /
0.14 to 17.2 bar
Maximum Inlet
300 psig / 20.7 bar
Pressure
Body Material Cast Iron and Steel
Bulletin No. 71.2:92W
The Type 92W regulator is piston actuated for high cycle liquid service. The design
utilizes hardened stainless steel trim for durability.
*Maximum temperature limitation may vary according to body and construction materials.
16
Body Size
NPS 2, 3, 4, 6, and 8 6 / DN 50,

80, 100, 150 and 200 x 150
Relief Pressure Range 15 to 375 psig / 1.0 to 25.9 bar

Maximum Inlet
450 psig / 31.0 bar
Pressure
Maximum Capacity 4900 gpm / 18,547 l/min
Body Material
Steel, Stainless Steel, Hastelloy

C, Monel, andAlloy 20
Bulletin No. 71.4: 63EG-98HM

The Type 63EG-98HM is a compact, fast response, high accuracy relief valve/backpressure
which is suitable for gas or liquid service. The valve's design makes it ideal for pump
recirculation especially in skid packages where space is limited. Available constructions
include units suitable for sea water applications.
Pressure Reducing
Relief/Backpressure
MR95 Series
MR98 Series
NPS 1/4, 1/2, 3/4, 1, 1-1/2, and 2 /

Body Size
DN 15, 20, 25, 40, and 50
Outlet Pressure
2 to 400 psig / 0.14 to 27.6 bar
Range
Maximum Inlet
1000 psig / 68.9 bar
Pressure
Body Material
of solving the toughest pressure control applications. Typical applications include fuel oil
steam atomization, sea water, fire water systems, and boiler feed water. The regulator
is available with differential pressure control, high temperature, and high-pressure
optionalconstructions.
NPS 1/4, 1/2, 3/4, 1, 1-1/2, and 2 /

DN 15, 20, 25, 40, and 50
2 to 375 psig /
0.14 to 25.9 bar
Maximum Inlet
400 psig / 27.6 bar
Pressure
Body Size

Body Material


The MR98 Series is used in a variety of liquid relief/backpressure applications, such as
pump recirculation, lube oil skids, heating and cooling systems, and process system. The
unit is available with a remote control line, differential pressure control and high-pressure
optional constructions.
Pressure Reducing
Relief/Backpressure
Type LR125
Type LR128
NPS 1, 2, 3, 4 /
Body Size
DN 25, 50, 80, and 100
Body Material
WCC Steel, CF8M or

CF3MStainless Steel

Bulletin No. 71.2:LR125
The Type LR125 pilot-operated, pressure reducing regulator is designed for liquid industrial/
commercial applications. The Type LR125 provides smooth operation, tight shutoff and
long life, even in dirty service. Its internally actuated metal plug eliminates disadvantages
associated with boot-style regulators, and the specially engineered flow path deflects debris,
protecting the seat from damage and erosion. The Type LR125 is used in conjunction with
a Type 95H pilot and Type 112 restrictor. An internal inlet strainer prevents large particles
from entering the main valve, limiting damage to internal parts.
Body Size

Maximum Capacity 3368 gpm / 12,748 l/min
Body Material
Bulletin No. 71.2:LR128

The Type LR128 pilot-operated, relief/backpressure regulator is designed for liquid industrial/
commercial applications. The Type LR128 provides smooth operation, tight shutoff and
long life, even in dirty service. Its internally actuated metal plug eliminates disadvantages
associated with boot-style regulators, and the specially engineered flow path deflects debris,
protecting the seat from damage and erosion. The Type LR128 is used in conjunction with
a Type 95HM pilot and Type 112 restrictor. An internal inlet strainer prevents large particles
from entering the main valve, limiting damage to internal parts.
Pressure Reducing
Type 1098-EGR
Type 75A
Maximum Capacity 11,934 gpm / 45,170 l/min

Body Material Cast Iron, Steel, Stainless Steel
Bulletin No. 71.2:1098-EGR
WCC Steel, CF8M or CF3M

Stainless Steel
Pressure Reducing
NPS 1, 2, 3, 4, 6, 8 x 6, and 12 x 6 /
Body Size DN 25, 50, 80, 100, 150, 200 x
150, and 300 x 150
Outlet Pressure 4 inches w.c. to 300 psig /
Maximum Inlet
400 psig / 27.6 bar
Pressure
NPS 1, 2, 3, and 4 /
DN 25, 50, 80, and 100
NPS 1/2, 3/4, 1, 1-1/2, 2, and

Body Size 2-1/2 / DN 15, 20, 25, 40, 50,
and 65
20 to 80 psig /
1.4 to 5.5 bar
Body Material Bronze
Bulletin No. 71.1:75A
The Type 1098 regulators are capable of providing accurate, fast response, and
high-capacities in low-pressure drop systems. Typical applications include: inert gas and
plant airheaders.
*Maximum temperature limitation may vary according to body and construction materials.
The 75A regulator is designed to reduce domestic or industrial water pressure, thus
protecting plumbing fixtures and meters from high pressure surges. Type 75A is selfcontained, requiring no external control line for operation. Downstream pressure is
directly registered under the diaphragm. As the downstream pressure increases, the
diaphragm force overcomes the spring compression, causes the valve disk to rise, and
reduces flow through the regulator.
17
Process Gas
Fully Balanced System
High-Capacity
High Sensitivity
Tight Shutoff
Low Setpoints
In-line Maintenance
Broad Material Selection
Pressure Reducing
Type 1098-EGR
NPS 1, 2, 3, 4, 6, 8 x 6, and 12 x 6 /
Body Size DN 25, 50, 80, 100, 150,
200 x 150, 300 x150
Outlet Pressure 4 inches w.c. to 300 psig /
Maximum Inlet
400 psig / 27.6 bar
Pressure
11,331,000 SCFH /
Maximum Capacity
303,671 Nm3/h
Gases are used in chemical and industrial

processes, such as analytical instrumentation,
environmental
compliance,
manufacturing,
chemical
electronic
production,
reference gases, and medical uses. All the

devices in these systems must be compatible
to prevent complications, such as corrosion,
unwanted chemical reactions, ignition, or
explosion. Also, some of these process systems
operate at very high or very low temperatures.
Regulators must be constructed to withstand
these temperatures.

The Type 1098 regulators are capable of providing accurate, fast response, and
high-capacities in low-pressure drop systems. Typical applications include: inert gas and
plant air headers.
Pressure Reducing
MR95 Series
Body Size
NPS 1/4, 1/2, 3/4, 1, 1-1/2, and 2 /

DN 15, 20, 25, 40, and 50

Maximum Inlet
1000 psig / 68.9 bar
Pressure
Maximum Capacity 510,000 SCFH / 13,668 Nm3/h
Body Material

Bulletin No. 71.1: MR95
The
regulators
and
relief/backpressure
regulators covered in this section are available

in materials that are chemically compatible
with most process gases. The products shown
in the Air, Liquids, and Sanitary sections may
also be used in your system if the materials
arecompatible.
18

of solving the toughest pressure control applications. Possible applications include
oxygen systems, inert gas systems, and corrosive gas service. The regulator is available
with cryogenic materials, differential pressure control, high temperature, and highpressure optional constructions.
Relief/Backpressure
Relief/Backpressure
MR98 Series
T208 Series
NPS 1/4, 1/2, 3/4, 1, 1-1/2, and 2 /

Body Size
DN 15, 20, 25, 40, and 50
2 to 375 psig /
0.14 to 25.9 bar
Maximum Inlet
400 psig / 27.6 bar
Pressure
Maximum Capacity 206,000 scfh / 5510 Nm3/h
Body Material


The MR98 Series is used in a variety of process gas backpressure and relief applications
including corrosive gases and cryogenic applications. The unit is available with a remote
control line, differential pressure control and high-pressure optional constructions.
NPS 3/4 and 1 /

DN 20 and 25
5 mbar to 0.48 bar
Body Size

Maximum Capacity 2286 SCFH / 61.3 Nm3/h
Body Material

The T208 Series is ideal for relief or backpressure applications in small systems. The unit
may also be utilized as a vapor recovery valve. A larger NPS 1-1/2 and 2 / DN 40 and 50
unit is available in the Type Y696.
Pressure Reducing
Vacuum Breaker
T205 Series
T205VB Series
NPS 3/4 and 1 /

Body Size
DN 20 and 25
2 mbar to 0.48 bar
2468 SCFH /
Maximum Capacity
346.2Nm3/h
Body Material

Stainless Steel

The T205 Series is a compact regulator idea for accurate control of low-pressure systems.
The unit is easy to install and maintain. For larger applications the Type Y692 is available in
NPS 1-1/2 and 2 / DN 40 and 50 sizes.

Stainless Steel
NPS 3/4 and 1 /

DN 20 and 25
0 to 5 psig /
0 to 0.35 bar vacuum
Body Size

Maximum Capacity 2468 SCFH / 66.1 Nm3/h
Body Material

Stainless Steel
Bulletin No. 71.3:T205VB

The T205VB Series vacuum breaker provides accurate vacuum protection with its large
diaphragm area. An external registration option is available for systems requiring a control
line. The Y692VB Series is available for larger systems needing a NPS 1-1/2 or 2 / DN 40 or
50 unit. For Vacuum Regulator applications, the T208VR and Y696VR Series are available.
19
Fuel Gas
High speed response
High-Capacity
Flexibility
Control Accuracy
Easy Maintenance
Safe Operation
Natural gas (methane) is a clean-burning fuel
gas used for many residential, commercial, and
industrial applications. This colorless, naturally
occurring gas can be found in many countries
Pressure Reducing
Type 310A
NPS 1, 2, 3, 4, and 4 x 6 /
Body Size DN 25, 50, 80, 100, and
100 x 150
Maximum Inlet
1500 psig / 103 bar
Pressure
21,170,000 SCFH /
Maximum Capacity
567,356 Nm3/h
Body Material WCC Steel
Bulletin No. 71.2:310A
The Type 310A pilot-operated high-pressure regulator is used where high-capacity , fast
response, and accurate control are essential. Typical applications include turbine startup
and power plant fuelsupply.
around the world.

For industrial applications, natural gas is used
as a feedstock for making chemicals, such as
anhydrous ammonia, and as a fuel for boilers
and furnaces.
Pressure Reducing
Type EZR
NPS 1, 1-1/4 x 1, 2 x 1, 2, 3,
4, 6, and 8 / DN 25, 32 x 25,
50 x 25, 50, 80, 100, 150,
and 200
Outlet Pressure 6-inches w.c. to 1000 psig /
Maximum Inlet
1500 psig / 103 bar
Pressure
26,138,000 SCFH /
Maximum Capacity
700,498 Nm3/h
Body Size

Body Material
Cast Iron and WCC or

LCC Steel
Bulletin No. 71.2:EZR

The Type EZR pilot-operated, pressure reducing regulator is designed for natural gas
transmission/distribution systems and industrial/commercial applications. The Type EZR
provides smooth, quiet operation, and tight shutoff.
Pressure Reducing
Y600A Series
NPS 3/4 and 1 /
DN 20 and 1
10 mbar to 0.48 bar
Maximum Inlet
150 psig / 10.3 bar
Pressure
6660 SCFH /
Maximum Capacity
178 Nm3/h of Natural Gas
Body Size

Body Material Cast Iron
Bulletin No. 71.1:Y600A
Y600A Series direct-operated, spring-loaded regulators provide economical pressurereducing control for a variety of residential, commercial, and industrial applications.
The large diaphragm area provides more accurate control at low-pressure settings.
The pitot tube of regulators also creates a dynamic boost that helps provide
greatercapacity.
20
Pressure Reducing
Pressure Reducing
Type 1098-EGR
Type 99
NPS 1, 2, 3, 4, 6, 8 x 6, and 12 x 6 /
Body Size DN 25, 50, 80, 100, 150, 200 x
150, and 300 x 150
4 inches w.c. to 300 psig /
10 mbar to 20.7 bar
Maximum Capacity
11,331,000 SCFH /
303,671 Nm3/h

The Type 1098 regulators are capable of providing accurate, fast response and
high-capacities in low-pressure drop systems. Typical applications include: natural gas
distribution systems; fuel gas supply to industrial boilers, furnaces, ovens, and mixers; and
large commercial/industrial establishments.
Body Size NPS 2 / DN 50

Maximum Inlet
1000 psig / 69.0 bar
Pressure
The Type 99 regulator is ideal for systems requiring accurate pressure control and fast
response. Typical applications include fuel supply to industrial boiler, gas engines,
furnaces, ovens, industrial burners, and dryers.
Pressure Reducing
Pressure Reducing
EZH and EZHSO Series
133 Series
NPS 1, 2, 3, and 4 /
Body Size
DN 25, 50, 80, and 100
14.5 to 1160 psig /
1 to 80.0 bar
Maximum Capacity
13,833,000 SCFH /
370,724 Nm3/h

Body Material Steel
Bulletin No. 71.2:EZH and EZHSO
The EZH and EZHSO Series regulators are accurate pilot-operated, pressure balanced, and
soft seated regulators. They are designed for use in large capacity distribution systems
and power plant feeds. They provide smooth, reliable operation, tight shutoff, and
longlife.
Body Size NPS 2 / DN 50

Maximum Inlet
150 psig / 10.3 bar
Pressure
The 133 Series is a high-capacity regulator with fast response ideal for snap-acting boiler
applications. The nits balanced trim design enables the regulator to provide accurate
control of gas pressure for maximum combustion efficiency despite varying inlet
pressureconditions.
21
Regulator Tips
All regulators should be installed and used in accordance with federal, state, and local codes andregulations.
PRESSURE
SIZING
Adequate overpressure protection should be installed

to protect the regulator from overpressure. Adequate
overpressure protection should also be installed to
protect all downstream equipment in the event of
regulator failure.
The recommended selection for orifice diameters is the

smallest orifice that will handle the flow.
Downstream pressures significantly higher than the

regulators pressure setting may damage soft seats and
other internal parts.
Do not oversize regulators. Pick the smallest orifice

size or regulator that will work. Keep in mind when
sizing a station that most restricted trims that do not
reduce the main port size do not help with improved low
flowcontrol.
When a regulator appears unable to pass the published

flow rate, be sure to check the inlet pressure measured
at the regulator body inlet connection. Piping up to
and away from regulators can cause significant flowing
pressure losses.
When adjusting setpoint, the regulator should be flowing
at least five percent of the normal operatingflow.
Droop is the reduction of outlet pressure experienced by
pressure reducing regulators as the flow rate increases. It
is stated as a percent, in inches of water column (mbar)
or in pounds per square inch (bar) and indicates the
difference between the outlet pressure setting made
at low flow rates and the actual outlet pressure at the
published maximum flow rate. Droop is also called offset
or proportional band.
Downstream pressure always changes to some extent
when inlet pressure changes.
A disk with a cookie cut appearance probably means you
had an overpressure situation. Thus, investigate further.
SPEED OF RESPONSE AND ACCURACY

If two or more available springs have published pressure
ranges that include the desired pressure setting, use the
spring with the lower range for better accuracy.
Direct-operated regulators generally have faster response
to quick flow changes than pilot-operatedregulators.
Speed of regulator response, in order:
- Direct-operated
- Two-path pilot-operated
- Unloading pilot-operated
- Control valve
Note: Although direct-operated regulators give the fastest
response, all types provide quick response.
The full advertised range of a spring can be utilized
without sacrificing performance or spring life.
22
Regulator body size should never be larger than the pipe

size. In many cases, the regulator body is one size smaller
than the pipe size.
Most soft-seated regulators will maintain the pressure

within reasonable limits down to zero flow. Therefore,
a regulator sized for a high flow rate will usually have
a turndown ratio sufficient to handle pilot-light loads
during off cycles.
Do not undersize the monitor set. It is important to realize
that the monitor regulator, even though it is wide-open,
will require pressure drop for flow. Using two identical
regulators in a monitor set will yield approximately
70percent of the capacity of a singleregulator.
TEMPERATURE
Most regulators shown in this handbook are generally
suitable for temperatures to 180F / 82C. With high
temperature Fluorocarbon (FKM) (if available), the
regulators can be used for temperatures to 300F /
149C. Check the temperature capabilities to determine
materials and temperature ranges available. Use stainless
steel diaphragms and seats for higher temperatures, such
as steam service.
For every 15 psid / 1.0 bar, differential pressure differential
across the regulator, expect approximately one degree
drop in gas temperature due to the natural refrigeration
effect. Freezing is often a problem when the ambient
temperature is between 30F / -1C and 45F / 7C.
Regulator Tips (continued)

INSTALLATION
Diaphragms leak a small amount due to migration of gas
through the diaphragm material. To allow escape of this
gas, be sure casing vents (where provided) remain open.
Vents should be pointed down to help avoid the

accumulation of water condensation or other materials
in the spring case.
Use control lines of equal or greater size than the control

tap on the regulator. If a long control line is required,
make it bigger. A rule of thumb is to use the next
nominal pipe size for every 20 feet / 6.1 meters of control
line. Small control lines cause a delayed response of
the regulator, leading to increased chance of instability.
3/8-inch OD tubing is the minimum recommended
control line size.
Make control line connections in a straight run of pipe

about 10 pipe diameters downstream of any area of
turbulence, such as elbows, pipe swages, or blockvalves.
When installing a working monitor station, get as much
volume between the two regulators as possible. This
will give the upstream regulator more room to control
intermediate pressure.
When using relief valves, be sure to remember that the

reseat point is lower than the start-to-bubble point. To
avoid seepage, keep the relief valve setpoint far enough
above the regulator setpoint.
For more Regulator Tips, turn to page 664 of the Industrial Application Guide Edition VI or log-on to www.fisherregulators.com
Emerson's sales, service and technical support are close at hand. Anywhere in the world, Emerson resources are
available by telephone or on our website. Our distribution network includes an experienced sales and support team,
with more than 2,000 technical experts available from nearly 200 offices throughout the world.
www.fisherregulators.com
23
Natural Gas Technologies
LP-Gas Equipment
TESCOM
Emerson Process Management

Regulator Technologies, Inc.



Tescom Corporation
North America
3200 Emerson Way
McKinney, Texas 75070 USA
Tel: +1 800 558 5853
Outside U.S. +1 972 548 3574
North America
3200 Emerson Way
Tel: +1 800 558 5853
Outside U.S. +1 972 548 3574
North America
3200 Emerson Way
Tel: +1 800 558 5853
Outside U.S. +1 972 548 3574
North America
Elk River, Minnesota 55330-2445, USA
Tel: +1 763 241 3238
+1 800 447 1250
Asia-Pacific
Shanghai 201206, China
Tel: +86 21 2892 9000
Asia-Pacific
Singapore 128461, Singapore
Tel: +65 6770 8337
Asia-Pacific
Singapore 128461, Singapore
Tel: +65 6770 8337
Europe
Bologna 40013, Italy
Tel: +39 051 419 0611
Europe
Bologna 40013, Italy
Tel: +39 051 419 0611
Chartres 28008, France
Tel: +33 2 37 33 47 00
Europe
Chartres 28008, France
Tel: +33 2 37 33 47 00
Middle East and Africa

Dubai, United Arab Emirates
Tel: +011 971 4811 8100
Latin America
Tlalnepantla 54080, Mexico
Tel: +11 52 55 2699 0400
For further information visit www.fisherregulators.com
Our Global Product Brand:
D351342X012 2013 Emerson Process Management Regulator Technologies, Inc. All rights reserved. Printed in China. 11/13.
Fisher, Emerson Process Management, and the Emerson Process Management design are marks of one of the Emerson Process
Management group of companies. All other marks are the property of their respective owners.
Europe
Selmsdorf 23923, Germany
Tel: +49 38823 31 287
Asia-Pacific
Shanghai 201206, China
Tel: +86 21 2892 9000

Press. Regulator

Uploaded by

Copyright:

Available Formats

Press. Regulator

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Press. Regulator

Uploaded by

Copyright:

Available Formats

Industrial Regulators

From Fahrenheit (F) to Kelvin (K)

From Celsius (C) to Fahrenheit (F)

From Celsius (C) to Kelvin (K)

From Kelvin (K) to Fahrenheit (F)

From Kelvin (K) to Celsius (C)

VOLUMETRIC GAS FLOW CONVERSION

VOLUMETRIC LIQUID FLOW CONVERSION

Tank Blanketing/Vapor Recovery

EZH and EZHSO Series . . . . . . . . . . . . . . . . . . . . . . . . 21

Regulator Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 -23

Pressure Reducing Regulators

Regulators are self-contained, control devices which use

Pressure Reducing Regulators

Pressure Reducing Regulator Type

The two main types of regulators:

Figure 2. Pilot-Operated Regulator

Figure 1. Direct-Operated Regulator

Pilot-Operated regulators are preferred for high flow rates

Pressure Reducing Regulator Selection

Relief Valve / Backpressure Regulator

Relief Valves and Backpressure Regulators

Relief Valve Types

Direct-Operated Relief Valves

Figure 4. Pilot-Operated Relief Valve

Pilot-operated relief valves are used in applications

large opening for relief

Figure 3. Direct-Operated Relief Valve

Direct-Operated relief valves are commonly used in industry

Pilot-Operated Relief Valves

Figure 5. Internal Relief

The relief valve assembly is located in the center of

Backpressure Regulator Selection

Industrial Regulators Selection Table

Pressure Reducing Regulators

Pressure Reducing Regulator

BODY SIZE, NPS

5 to 300 / 0.34 to 20.7

0.25"wc-7 / 0.6 mbar-0.48

1"w.c.-7 psig / 2 mbar-0.48 bar

-5"wc-1.5 / -12 mbar-0.10

-5"wc-1.5 / -12 mbar-0.10

1/2, 1 x 1/2, and 1

-5"wc-1.5 / -12 mbar-0.10

Pad: 0.5"wc-2.2 / 1 mbar-0.15

Pad: 1/2, 1, and 2 and

1-1/4, 1-1/2, and 2

BODY SIZE, NPS

35-375 / 2.4- 25.9

1-1/4 ,1-1/2, and 2

1/4, 3/4, 1, and 2

5 to 300 / 0.34 to 20.7

3/4, 1, and 1-1/4

1/4 and 1/2

1/4 and 1/2

0-5 / 0-0.35 vacuum

This catalog is a brief overview of the Fisher product line.

NPS 1/4, 1/2, 3/4, 1, 1-1/2, and 2 /

Outlet Pressure Range 2 to 400 psig / 0.14 to 27.6 bar

Manufacturing and process plants use