Rear Axle

REAR AXLE
SECTION
RAX
B
RAX
N
O
P
CONTENTS
SERVICE INFORMATION ...........................
PRECAUTIONS
2
.................................................. 2
Precaution for Supplemental Restraint System

(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
.................................................................. 2
Precaution Necessary for Steering Wheel Rotation
After Battery Disconnect .................................... 2
Caution ..................................................................... 3
PREPARATION .................................................. 4
Commercial Service Tool ......................................... 4
NOISE, VIBRATION AND HARSHNESS

(NVH) TROUBLESHOOTING ............................ 5
NVH Troubleshooting Chart .................................... 5
WHEEL HUB ...................................................... 6

On-Vehicle Inspection and Service ......................... 6
Removal and Installation ......................................... 6
SERVICE DATA AND SPECIFICATIONS

(SDS) .................................................................. 8
Wheel Bearing ......................................................... 8
Revision: October 2008 2009 Sentra
RAX-2
< SERVICE INFORMATION >
PRECAUTIONS
SERVICE INFORMATION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT
PRE-TENSIONER"
INFOID:0000000004783751
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER,
used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front
passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag
modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only
deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or
unbelted.
Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal
injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be
performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS can
lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and
Air Bag
Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed
to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange
harnesses or harness
connectors.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors
with the Ignition
ON or engine running, DO NOT use air or electric power tools or strike near the
sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing
serious injury.
When using air or electric power tools or hammers, always switch the Ignition OFF,
disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery

Disconnect
INFOID:0000000004732582
NOTE:
This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN
ANTI-THEFT SYSTEM).
Remove and install all control units after disconnecting both battery cables with the ignition
knob in the
LOCKposition.
Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after
finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled
steering lock mechanism
is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel
will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure
below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ACCposition. At
this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering
wheel can be
rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the LOCKposition before
connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
PRECAUTIONS
RAX-3
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
Caution
INFOID:0000000004732580
Observe the following precautions when disassembling and assembling drive shaft.
Perform work in a location which is as dust-free as possible.
Before disassembling and assembling, clean the outside of parts.
Prevention of the entry of foreign objects must be taken into account during disassembly of
the service location.
Disassembled parts must be carefully reassembled in the correct order. If work is interrupted,
a clean cover
must be placed over parts.
Paper shop cloths must be used. Fabric shop cloths must not be used because of danger of
lint adhering to
parts.
Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be
removed by
blowing with air or wiping with paper shop cloths.
RAX-4
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000004407341
Tool name Description

Power tool Removing wheel nuts
PBIC0190E
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

RAX-5
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
NOISE, VIBRATION AND HARSHNESS (NVH)

TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000004407342
Use chart below to help you find the cause of the symptom. If necessary, repair or replace
these parts.
: Applicable
Reference page
RAX-6
RAX-6
RSU-4, "NVH Troubleshooting Chart"
WT-4, "NVH Troubleshooting Chart"
WT-4, "NVH Troubleshooting Chart"
BR-4, "NVH Troubleshooting Chart"
PS-6, "NVH Troubleshooting Chart"
Possible cause and SUSPECTED PARTS
Improper installation, looseness
Wheel bearing damage
REAR SUSPENSION
TIRES
ROAD WHEEL
BRAKES
STEERING
Symptom REAR AXLE
Noise
Shake
Vibration
Shimmy
Shudder
Poor quality ride or handling
RAX-6
WHEEL HUB
WHEEL HUB
On-Vehicle Inspection and Service
INFOID:0000000004407343
Check the axle and suspension parts for excessive play, wear, or damage.
Shake each rear wheel to check for excessive play as shown.
REAR WHEEL BEARING INSPECTION

Move wheel hub and bearing assembly in the axial direction by hand. Make sure the axial
end play is within
specification.
Check that the wheel hub bearing operates smoothly.
Replace the wheel hub assembly if the axial end play exceeds specification, or if the wheel
bearing does not
turn smoothly. Refer to RAX-6, "Removal and Installation".
CAUTION:
The wheel hub assembly does not require maintenance. If any of the following
symptoms are noted,
replace the wheel hub assembly.
Growling noise is emitted from the wheel hub bearing during operation.
Wheel hub bearing drags or turns roughly.
Removal and Installation
INFOID:0000000004407344
COMPONENTS
REMOVAL
SMA525A
Axial end play : 0.05 mm (0.002 in) or less

1. Wheel hub and bearing assembly
(disc brake)
2. Baffle plate 3. Rear suspension beam
4. Back plate 5. Wheel hub and bearing assembly
(drum brake)
WDIA0386E
WHEEL HUB
RAX-7
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
1. Remove wheel and tire using power tool.
2. Remove wheel sensor from wheel hub and bearing assembly, if equipped. Refer to BRC-31,
"Removal
and Installation".
CAUTION:
Do not pull on wheel sensor harness.
3. Remove the brake assembly. Refer to BR-41, "Removal and Installation of Drum Brake
Assembly" (Drum
brake), BR-35, "Removal and Installation of Caliper Assembly" (Disc brake).
4. Remove wheel hub and bearing assembly bolts, and then remove wheel hub and bearing
assembly.
5. Remove baffle plate or back plate, if necessary.
a. Remove parking brake rear cable from baffle plate or back plate. Refer to PB-4, "On-Vehicle
Service".
b. Separate brake tube from wheel cylinder, if equipped. Refer to BR-10, "Hydraulic Circuit".
INSPECTION AFTER REMOVAL

Check for any deformity, cracks, or other damage on the wheel hub assembly, replace if
necessary.
CAUTION:
The wheel hub assembly does not require maintenance. If any of the following
symptoms are noted,
replace the wheel hub assembly.
Growling noise is emitted from the wheel hub bearing during operation.
Wheel hub bearing drags or turns roughly.
INSTALLATION
Installation is in the reverse order of removal.
Tighten wheel nuts to specification. Refer to WT-8, "Rotation".
RAX-8
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Bearing
INFOID:0000000004407345
Axial end play 0.05 mm (0.002 in) or less

Rear Axle

Uploaded by

Copyright:

Available Formats

Rear Axle

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Rear Axle

Uploaded by

Copyright:

Available Formats

REAR AXLE

Precaution for Supplemental Restraint System

NOISE, VIBRATION AND HARSHNESS

WHEEL HUB ...................................................... 6

SERVICE DATA AND SPECIFICATIONS

Precaution Necessary for Steering Wheel Rotation After Battery

Tool name Description

Revision: October 2008 2009 Sentra

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NOISE, VIBRATION AND HARSHNESS (NVH)

Revision: October 2008 2009 Sentra

REAR WHEEL BEARING INSPECTION

Removal and Installation

Axial end play : 0.05 mm (0.002 in) or less

Revision: October 2008 2009 Sentra

1. Remove wheel and tire using power tool.

INSPECTION AFTER REMOVAL

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Axial end play 0.05 mm (0.002 in) or less

You might also like