Professional Documents
Culture Documents
Acc PDF
Acc PDF
SECTION
ACC
ACC
CONTENTS
SERVICE INFORMATION ........................ .... 2
PRECAUTIONS .............................................. ..... 2
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ............................................................. ...... 2 Precaution Necessary for Steering Wheel Rotation After Battery Disconnect ............................... ..... 2
ACC-1
2009 Versa
PRECAUTIONS
< SERVICE INFORMATION >
SERVICE INFORMATION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
INFOID:0000000004305261
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the SRS and SB section of this Service Manual. WARNING: To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS section. Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
NOTE: This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM). Remove and install all control units after disconnecting both battery cables with the ignition knob in the LOCK position. Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results. For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted on the key cylinder. For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and steering wheel rotation will become impossible. If steering wheel rotation is required when battery power is interrupted, follow the procedure below before starting the repair operation.
OPERATION PROCEDURE
1. 2. 3. 4. 5. 6. Connect both battery cables. NOTE: Supply power using jumper cables if battery is discharged. Use the Intelligent Key or mechanical key to turn the ignition switch to the ACC position. At this time, the steering lock will be released. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be rotated. Perform the necessary repair operation. When the repair work is completed, return the ignition switch to the LOCK position before connecting the battery cables. (At this time, the steering lock mechanism will engage.) Perform a self-diagnosis check of all control units using CONSULT-III.
ACC-2
2009 Versa
ACC
G
PBIC3813E
1.
2.
Locating pin
3.
INFOID:0000000004305263
CAUTION: Do not disassemble accelerator pedal assembly. Do not remove accelerator pedal position sensor from accelerator pedal assembly. Avoid impact from dropping etc. during handling. Be careful to keep accelerator pedal assembly away from water.
REMOVAL
1. 2. 3. Disconnect the negative battery terminal. Disconnect accelerator pedal position sensor harness connector. Loosen mounting bolts, and remove accelerator pedal assembly.
INSTALLATION
Note the following, and install in the reverse order of removal. Insert locating pin into vehicle side to position accelerator pedal assembly. Install mounting bolt to accelerator pedal assembly. Align the stud bolt on the floor with the thread hole to insert accelerator pedal stopper until it contacts the face.
M
ACC-3
2009 Versa