Installation and Commisioning Manual REC670

Installation and commissioning manual
Bay control IED

REC 670 ANSI
Innovation
from
ABB
Document ID: 1MRK511189-UUS

Issued: December 2007
Revision: A
IED product version: 1.1
Copyright 2007 ABB. All rights reserved
COPYRIGHT
WE RESERVE ALL RIGHTS TO THIS DOCUMENT, EVEN IN THE EVENT
THAT A PATENT IS ISSUED AND A DIFFERENT COMMERCIAL
PROPRIETARY RIGHT IS REGISTERED. IMPROPER USE, IN PARTICULAR
REPRODUCTION AND DISSEMINATION TO THIRD PARTIES, IS NOT
PERMITTED.
THIS DOCUMENT HAS BEEN CAREFULLY CHECKED. HOWEVER, IN
CASE ANY ERRORS ARE DETECTED, THE READER IS KINDLY
REQUESTED TO NOTIFY THE MANUFACTURER AT THE ADDRESS
BELOW.
THE DATA CONTAINED IN THIS MANUAL IS INTENDED SOLELY FOR
THE CONCEPT OR PRODUCT DESCRIPTION AND IS NOT TO BE DEEMED
TO BE A STATEMENT OF GUARANTEED PROPERTIES. IN THE INTEREST
OF OUR CUSTOMERS, WE CONSTANTLY SEEK TO ENSURE THAT OUR
PRODUCTS ARE DEVELOPED TO THE LATEST TECHNOLOGICAL
STANDARDS. AS A RESULT, IT IS POSSIBLE THAT THERE MAY BE SOME
DIFFERENCES BETWEEN THE HW/SW PRODUCT AND THIS
INFORMATION PRODUCT.
Manufacturer:
ABB AB
Substation Automation Products
SE-721 59 Vsters
Sweden
Telephone: +46 (0) 21 34 20 00
Facsimile: +46 (0) 21 14 69 18
www.abb.com/substationautomation
Table of contents
Table of contents
Section 1
Introduction..........................................................................11
Introduction to the installation and commissioning manual....................11
About the complete set of manuals for an IED..................................11
About the installation and commissioning manual.............................12
Intended audience.............................................................................13
Related documents............................................................................13
Revision notes...................................................................................14
Section 2
Safety information...............................................................15
Warning signs.........................................................................................15
Caution signs..........................................................................................16
Note signs...............................................................................................17
Section 3
Overview.............................................................................19
Commissioning and installation overview...............................................19
Section 4
Unpacking and checking the IED........................................21

Taking delivery, unpacking and checking...............................................21
Section 5
Installing the IED.................................................................23

Overview.................................................................................................23
Dimensions.............................................................................................23
Case without rear cover.....................................................................23
Case with rear cover..........................................................................24
Flush mounting dimensions...............................................................26
Side-by-side flush mounting dimensions...........................................27
Wall mounting dimensions.................................................................28
Mounting methods and details................................................................29
Mounting the IED...............................................................................29
Flush mounting..................................................................................30
Overview.......................................................................................30
Mounting procedure for flush mounting........................................31
19 panel rack mounting....................................................................32
Overview.......................................................................................32
Mounting procedure for 19 panel rack mounting.........................33
Wall mounting....................................................................................34
Overview.......................................................................................34
REC 670 ANSI

1MRK511189-UUS rev. A
Table of contents
Mounting procedure for wall mounting.........................................34

How to reach the rear side of the IED..........................................35
Side-by-side 19 rack mounting.........................................................36
Overview.......................................................................................36
Mounting procedure for side-by-side rack mounting....................37
IED 670 mounted with a RHGS6 case.........................................38
Side-by-side flush mounting..............................................................38
Overview.......................................................................................38
Mounting procedure for side-by-side flush mounting....................39
Making the electrical connection.............................................................40
IED connectors..................................................................................40
Overview.......................................................................................40
Front side connectors...................................................................42
Rear side connectors....................................................................42
Connection diagrams....................................................................47
Connection examples...................................................................53
Connecting to protectiveground.........................................................56
Connecting the power supply module...............................................57
Configuration for analog CT inputs....................................................57
Connecting to CT and VT circuits......................................................58
Connecting the binary input and output signals.................................59
Making the screen connection...........................................................60
Optical connections................................................................................61
Connecting station communication interfaces (OEM and SLM)........61
Connecting remote communication interfaces (LDCM).....................62
Galvanic X.21 line data communication (X.21-LDCM)...........................63
Connecting Galvanic X.21 line data communication module (X.
21 LDCM)..........................................................................................63
Installing the serial communication cable for RS485..............................65
RS485 serial communication module................................................65
Installing the serial communication cable for RS485 SPA/IEC..........69
Data on RS485 serial communication module cable.........................70
Installing the GPS antenna.....................................................................71
Installing the GPS antenna................................................................71
Antenna installation......................................................................71
Electrical installation.....................................................................72
Section 6
Checking the external optical and electrical

connections.........................................................................75
Overview.................................................................................................75

REC 670 ANSI
Table of contents
Checking the VT circuits.........................................................................75

Check of CT circuits................................................................................76
Checking the power supply.....................................................................77
Checking the binary I/O circuits..............................................................77
Binary input circuits............................................................................77
Binary output circuits.........................................................................77
Checking the optical connections...........................................................77
Section 7
Energizing the IED..............................................................79

Overview.................................................................................................79
Energizing the IED..................................................................................79
Checking the self supervision signals.....................................................82
Reconfiguring the IED.......................................................................82
Setting the IED time...........................................................................82
Checking the self supervision function..............................................83
Determine the cause of an internal failure....................................83
Self supervision HMI data..................................................................83
Section 8
Set up PCM 600 communication link per IED.....................85

Set up PCM 600 communication link per IED.........................................85
Section 9
Establishing connection and verifying the SPA/IECcommunication ...................................................................91

Entering settings.....................................................................................91
Entering SPA settings........................................................................91
Entering IEC settings.........................................................................92
Verifying the communication...................................................................92
Verifying SPA communication...........................................................92
Verifying IEC communication............................................................93
Fibre optic loop.......................................................................................93
Optical budget calculation for serial communication with SPA/IEC .......95
Section 10 Establishing connection and verifying the LON

communication ...................................................................97
Communication via the rear ports ..........................................................97
LON communication..........................................................................97
The LON Protocol..............................................................................99
Hardware and software modules.......................................................99
Optical budget calculation for serial communication with LON ............101
Section 11 Configuring the IED and changing settings.......................103

Overview...............................................................................................103
REC 670 ANSI

Table of contents
Entering settings through the local HMI................................................104

Analog input data..................................................................................104
Configuration for analog CT inputs..................................................104
Downloading settings and configuration from a PC..............................105
Downloading the configuration and setting files..............................105
Section 12 Verifying settings by secondary injection .........................107

Overview...............................................................................................107
Preparing for test..................................................................................108
Overview..........................................................................................108
Preparing the connection to the test equipment..............................109
Putting the IED into test mode.........................................................110
Connecting test equipment to the IED.............................................110
Verifying the connections and the analog inputs.............................111
Releasing the function(s) to be tested.............................................112
Disturbance report...........................................................................113
Introduction.................................................................................113
Disturbance report settings.........................................................113
Disturbance recorder (DR).........................................................113
Event recorder (ER)....................................................................114
Identifying the function to test in the technical reference
manual ............................................................................................114
Exit test mode..................................................................................114
Basic IED functions...............................................................................114
Parameter setting groups (ACGR)..................................................114
Verifying the settings..................................................................115
Completing the test.....................................................................115
Differential protection............................................................................115
High impedance differential protection (PDIF, 87)...........................115
Current protection.................................................................................116
Instantaneous phase overcurrent protection (PIOC, 50) ................116
Measuring the operate limit of set values...................................117
Four step phase overcurrent protection (PTOC, 51/67)..................117
Instantaneous residual overcurrent protection (PIOC, 50N) ...........119

REC 670 ANSI
Table of contents

Four step residual overcurrent protection (PTOC, 51N/67N)..........120
Four step directional overcurrent protection...............................120
Four step non-directional overcurrent protection........................120
Sensitive directional residual overcurrent and power protection
(PSDE, 67N)....................................................................................121
Measuring the operate and time limit for set values...................122
Thermal overload protection, one time constant (PTTR, 26)...........127
Measuring the operate and time limit of set values....................127
Thermal overload protection, two time constants (PTTR, 49) ........128
Checking operate and reset values............................................128
Breaker failure protection (RBRF, 50BF).........................................129
Checking the phase current operate value, Pickup_PH.............130
Checking the residual (GF) current operate value
Pickup_N set below Pickup_PH.............................................131
Checking the re-trip and back-up times......................................131
Verifying the re-trip mode...........................................................131
Verifying the back-up trip mode..................................................132
Verifying instantaneous back-up trip at CB faulty
condition ....................................................................................133
Verifying the case FunctionMode = Contact...............................134
Verifying the function mode Curr&Cont Check........................134
Stub protection (PTOC, 50STB)......................................................135
Polediscrepancy protection (RPLD, 52PD)....................................136
Directional underpower protection (PDUP) ....................................138
Directional overpower protection (PDOP) ......................................140
Broken conductor check (BRC).......................................................141
REC 670 ANSI

Table of contents
Measuring the operate and time limit of set values....................141

Voltage protection.................................................................................142
Two step undervoltage protection (PTUV, 27)................................142
Two step overvoltage protection (PTOV, 59)..................................143
Two step residual overvoltage protection (PTOV, 59N)..................144
Voltage differential protection (PTOV, 60).......................................144
Check of undervoltage levels.....................................................145
Check of voltage differential trip and alarm levels......................147
Check of trip and trip reset timers...............................................148
Final adjustment of compensation for VT ratio differences .......148
Loss of voltage check (LOV)...........................................................149
Frequency protection............................................................................150
Underfrequency protection (PTUF, 81)...........................................150
Overfrequency protection (PTOF, 81).............................................151
Rate-of-change frequency protection (PFRC, 81)...........................152
Multipurpose protection........................................................................153
General current and voltage protection (GAPC)..............................153
Built-in overcurrent feature (non-directional)..............................154
Overcurrent feature with current restraint...................................154
Overcurrent feature with voltage restraint..................................155
Overcurrent feature with directionality........................................155
Over/Undervoltage feature.........................................................156
Secondary system supervision.............................................................156

REC 670 ANSI
Table of contents
Current circuit supervision (RDIF)...................................................156

Fuse failure supervision (RFUF)......................................................157
Checking that the binary inputs and outputs operate as
expected ....................................................................................157
Measuring the operate value for the negative sequence
function ......................................................................................158
Measuring the operate value for the zero sequence
function ......................................................................................159
Checking the operation of the duv/dt and di/dt based
function ......................................................................................159
Control..................................................................................................160
Synchronism-check and energizing check (RSYN, 25)...................160
Testing the synchronizing function.............................................162
Testing the synchronism check..................................................164
Testing the energizing check......................................................167
Testing the voltage selection......................................................168
Autorecloser (RREC, 79).................................................................170
Preparation of the verification ....................................................172
Switching the auto-reclosing function Enabled and
Disabled .....................................................................................173
Verifying the auto-reclosing function .........................................173
Checking the reclosing conditions .............................................174
Apparatus control (APC)..................................................................176
Interlocking......................................................................................176
Voltage control (VCTR)...................................................................177
Secondary test............................................................................178
Check the activation of the Voltage Control Operation...............179
Check normal voltage regulation function..................................180
Check the setting of UVBlock.....................................................180
Check the setting of parameter UVmin and UVmax...................181
Overcurrent blocking..................................................................181
Single transformer......................................................................181
Parallel voltage regulation..........................................................183
Scheme communication.......................................................................187
REC 670 ANSI

Table of contents
Scheme communication logic for distance protection (PSCH,

85) ...................................................................................................187
Testing permissive underreach..................................................187
Testing permissive overreach.....................................................188
Testing blocking scheme............................................................188
Checking of unblocking logic......................................................189
Current reversal and weak end infeed logic for distance
protection (PSCH, 85) ....................................................................189
Current reversal logic.................................................................189
Weak end infeed logic................................................................190
Local acceleration logic (PLAL).......................................................191
Scheme communication logic for residual overcurrent protection
(PSCH, 85) .....................................................................................192
Testing the directional comparison logic function.......................192
Current reversal and weak end infeed logic for residual
overcurrent protection (PSCH, 85) .................................................194
Testing the current reversal logic...............................................194
Testing the weak-end-infeed logic..............................................194
Logic.....................................................................................................196
Tripping logic (PTRC, 94)................................................................196
Three phase operating mode.....................................................196
1ph/3ph operating mode.............................................................197
1ph/2ph/3ph operating mode......................................................197
Circuit breaker lockout................................................................198
Monitoring.............................................................................................199
Event counter (GGIO)......................................................................199
Event function (EV)..........................................................................199
Fault locator (RFLO)........................................................................200
Measuring the operate limit........................................................200
Metering................................................................................................202
Pulse counter logic (GGIO).............................................................202
Station communication.........................................................................202

REC 670 ANSI
Table of contents
Multiple command and trasmit (CM, MT).........................................202

Single command (CD).....................................................................202
Remote communication........................................................................202
Binary signal transfer to remote end................................................202
Section 13 Primary injection testing....................................................205

Primary injection testing........................................................................205
Voltage control (VCTR)...................................................................205
Load drop compensation function, LDC.....................................205
Testing the LDC function............................................................206
Voltage control of Parallel Transformers....................................208
Minimum Circulating Current (MCC) method.............................208
Master Follower (MF) method....................................................210
Section 14 Commissioning and maintenance of the fault clearing

system...............................................................................213
Installation and commissioning.............................................................213
Commissioning tests.............................................................................214
Periodic maintenance tests...................................................................214
Visual inspection..............................................................................215
Maintenance tests...........................................................................215
Preparation.................................................................................216
Recording...................................................................................216
Secondary injection....................................................................216
Alarm test...................................................................................216
Self supervision check................................................................217
Trip circuit check.........................................................................217
Measurement of service currents...............................................217
Restoring....................................................................................218
Section 15 Fault tracing and repair.....................................................219

Fault tracing..........................................................................................219
Information on the local HMI............................................................219
Using front-connected PC or SMS..................................................221
Repair instruction..................................................................................222
Repair support......................................................................................223
Maintenance.........................................................................................224
Section 16 Glossary............................................................................225
Glossary................................................................................................225
REC 670 ANSI

10
Section 1
Introduction
Section 1
Introduction
About this chapter
This chapter introduces the user to the manual.
1.1
Introduction to the installation and commissioning

manual
1.1.1
About the complete set of manuals for an IED

The users manual (UM) is a complete set of five different manuals:
Application
manual
Technical
reference
manual
Installation and
commissioning
manual
Operators
manual
Engineering
guide
en06000097.vsd
The Application Manual (AM) contains application descriptions, setting guidelines and
setting parameters sorted per function. The application manual should be used to find out
when and for what purpose a typical protection function could be used. The manual should
also be used when calculating settings.
The Technical Reference Manual (TRM) contains application and functionality
descriptions and it lists function blocks, logic diagrams, input and output signals, setting
parameters and technical data sorted per function. The technical reference manual should
be used as a technical reference during the engineering phase, installation and
commissioning phase, and during normal service.
The Installation and Commissioning Manual (ICM) contains instructions on how to
install and commission the protection IED. The manual can also be used as a reference
during periodic testing. The manual covers procedures for mechanical and electrical
installation, energizing and checking of external circuitry, setting and configuration as
well as verifying settings and performing directional tests. The chapters are organized in
REC 670 ANSI

11
Section 1
Introduction
the chronological order (indicated by chapter/section numbers) in which the protection

IED should be installed and commissioned.
The Operators Manual (OM) contains instructions on how to operate the protection
IED during normal service once it has been commissioned. The operators manual can
be used to find out how to handle disturbances or how to view calculated and measured
network data in order to determine the cause of a fault.
The IED 670 Engineering guide (EG) contains instructions on how to engineer the IED
670 products. The manual guides to use the different tool components for IED 670
engineering. It also guides how to handle the tool component available to read disturbance
files from the IEDs on the basis of the IEC 61850 definitions. The third part is an
introduction about the diagnostic tool components available for IED 670 products and
the PCM 600 tool.
The IEC 61850 Station Engineering guide contains descriptions of IEC 61850 station
engineering and process signal routing. The manual presents the PCM 600 and CCT tool
used for station engineering. It describes the IEC 61850 attribute editor and how to set
up projects and communication.
1.1.2
About the installation and commissioning manual

The installation and commissioning manual contains the following chapters:
12
The chapter Safety information presents warning and note signs, that the user
should pay attention to.
The chapter Overview is a summary of the major tasks faced when installing and
commissioning an IED.
The chapter Unpacking and checking the IED explains how to take delivery of
the IED.
The chapter Installing the IED explains how to install the IED.
The chapter Checking the external optical and electrical connections explains
how to check that the IED is properly connected to the protection system.
The chapter Energizing the IED explains how to start the IED.
The chapter Establishing connection and verifying the SPA/IEC-communication
contains explains how to enter SPA/IEC settings and verifying the SPA/IEC
communication.
The chapter Establishing connection and verifying the LON communication
contains a reference to another document.
The chapter Configuring the IED and changing settings explains how to download
settings and configure the terminal.
The chapter Verifying settings by secondary injection contains instructions on how
to verify that each included function operates correctly according to the set values.

REC 670 ANSI
Section 1
Introduction
1.1.3
The chapter Commissioning and maintenance of the fault clearing system

discusses maintenance tests and other periodic maintenance measures.
The chapter Fault tracing and repair explains how to troubleshoot.
The chapter Glossary is a list of terms, acronyms and abbreviations used in ABB
technical documentation.
Intended audience
General
The installation and commissioning manual addresses the personnel responsible for the
installation, commissioning, maintenance and taking the protection in and out of normal
service.
Requirements
The installation and commissioning personnel must have a basic knowledge in handling
electronic equipment. The commissioning and maintenance personnel must be well
experienced in using protection equipment, test equipment, protection functions and the
configured functional logics in the protection.
1.1.4
Related documents
Documents related to REC 670
Identity number
Operators manual
1MRK 511 188-UUS
1MRK 511 189-UUS
Technical refernce manual
1MRK 511 187-UUS
Application manual
1MRK 511 190-UUS
Buyers guide
1MRK 511 192-BUS
Connection diagram, Single breaker
1MRK 002 801-FA
Connection diagram, Double breaker
1MRK 002 801-MA
Connection diagram, breaker-and-a-half CB
1MRK 002 801-NA
Configuration diagram A, Single breaker arr. with single or double busbar
1MRK 004 500-90
Configuration diagram B, Double breaker arrangements
1MRK 004 500-91
Configuration diagram C, breaker-and-a-half breaker arr. for a full bay
1MRK 004 500-92
Connection and Installation components
1MRK 013 003-BEN
Test system, COMBITEST
1MRK 512 001-BEN
Accessories for IED 670
1MRK 514 012-BEN
Getting started guide IED 670
1MRK 500 080-UUS
Table continued on next page
REC 670 ANSI

13
Section 1
Introduction
SPA and LON signal list for IED 670, ver. 1.1
1MRK 500 083-WEN
IEC 61850 Data objects list for IED 670, ver. 1.1
1MRK 500 084-WEN
Generic IEC 61850 IED Connectivity package
1KHA001027-UEN
Protection and Control IED Manager PCM 600 Installation sheet
1MRS755552
Engineering guide IED 670 products
1MRK 511 179-UEN
Latest versions of the described documentation can be found on www.abb.com/substationautomation
1.1.5
Revision notes
Revision
A
14
Description
No functionality added. Minor changes made in content due to problem reports.

REC 670 ANSI
Section 2
Safety information
Section 2
Safety information
About this chapter
This chapter contains safety information. Warning signs are presented which urge the
user to be careful during certain operations in order to avoid injuries to humans or damage
to equipment.
2.1
Warning signs
Strictly follow the company and country safety regulations. Working in
a high voltage environment requires serious approach to avoid human
injuries and damage to equipment.
Do not touch circuitry during operation. Potentially lethal voltages and

currents are present.
Always avoid touching the circuitry when covers are removed. The
product contains electronic circuits which can be damaged if exposed to
static electricity (ESD). Lethal high voltage circuits are also exposed
when covers are removed.
Always use suitable isolated test pins when measuring signals in open
circuitry. Potentially lethal voltages and currents are present.
Never connect or disconnect a wire and/or a connector to or from a IED

during normal operation. Hazardous voltages and currents are present that
may be lethal. Operation may be disrupted and IED and measuring
circuitry may be damaged.
REC 670 ANSI

15
Section 2
Safety information
Always connect the IED to protective earth, regardless of the operating

conditions. This also applies to special occasions such as bench testing,
demonstrations and off-site configuration. Operating the IED without
proper earthing may damage both IED and measuring circuitry and may
cause injuries in case of an accident.
Never disconnect the secondary connection of current transformer circuit

without short-circuiting the transformers secondary winding. Operating
a current transformer with the secondary winding open will cause a
massive potential build-up that may damage the transformer and may
cause injuries to humans.
Never remove any screw from a powered IED or from a IED connected
to powered circuitry. Potentially lethal voltages and currents are present.
Take adequate measures to protect the eyes. Never look into the laser
beam.
2.2
Caution signs
Always transport PCBs (modules) using certified conductive bags.
Always handle modules using a conductive wrist strap connected to
protective ground and on a suitable antistatic surface. Electrostatic
discharge (ESD) may cause damage to the module since electronic
circuits are sensitive to this phenomena.
Do not connect live wires to the IED. Internal circuitry may be damaged
Always use a conductive wrist strap connected to protective ground when

replacing modules. Electrostatic discharge (ESD) may damage the
module and IED circuitry.
16

REC 670 ANSI
Section 2
Safety information
Take care to avoid electrical shock if accessing wiring and connection

IEDs when installing and commissioning.
Changing the active setting group will inevitably change the IEDs
operation. Be careful and check regulations before making the change.
2.3
Note signs
The protection assembly is designed for a maximum continuous current
of four times rated value.
REC 670 ANSI

17
18
Section 3
Overview
Section 3
Overview
About this chapter
This chapter outlines the installation and commissioning of the IED.
3.1
Commissioning and installation overview

The settings for each function must be calculated before the commissioning task can start.
A configuration, done in the configuration and programming tool, must also be available
if the IED does not have a factory configuration downloaded.
The IED is unpacked and visually checked. It is preferably mounted in a cubicle or on a
wall. The connection to the protection system has to be checked in order to verify that
the installation is successful.
REC 670 ANSI

19
20
Section 4
Unpacking and checking the IED
Section 4
Unpacking and checking the IED

About this chapter
This chapter describes the delivery and the unpacking of the IED
4.1
Taking delivery, unpacking and checking

Procedure
1.
2.
3.
4.
5.
REC 670 ANSI
Remove the transport casing.

Visually inspect the IED.
Check that all items are included in accordance with the delivery documents.
Once the IED has been started make sure that the software functions ordered have
been included in the delivery.
Check for transport damages.
If transport damage is discovered appropriate action must be taken against the latest
carrier and the nearest ABB office or representative should be informed. ABB
should be notified immediately if there are any discrepancies in relation to the
delivery documents.
Storage
If the IED is to be stored before installation, this must be done in the original
transport casing in a dry and dust free place. Observe the environmental
requirements stated in the technical data.

21
22
Section 5
Installing the IED
Section 5
Installing the IED

About this chapter
This chapter describes how to install the IED.
5.1
Overview
The mechanical and electrical environmental conditions at the installation site must be
within the limits described in the IED technical data. Dusty, damp places, places
susceptible to rapid temperature variations, powerful vibrations and shocks, surge
voltages of high amplitude and fast rise time, strong induced magnetic fields or similar
extreme conditions should be avoided.
Sufficient space must be available in front of and at the rear of the IED to allow access
for maintenance and future modifications. Flush mounted IEDs should be mounted so
that IED modules can be added and replaced without excessive dismantling.
5.2
Dimensions
5.2.1
Case without rear cover
REC 670 ANSI

23
Section 5
Installing the IED
D
F
Figure 1:
xx04000464.vsd
Figure 2:
Case size
(inches)
G
H
xx04000448.vsd

with 19 rack mounting kit
6U, 1/2 x 19
10.47
8.81
7.92
9.96
8.10
7.50
8.02
7.39
6U, 3/4 x 19
10.47
13.23
7.92
9.96
12.52
7.50
12.44
7.39
6U, 1/1 x 19
10.47
17.65
7.92
9.96
16.94
7.50
16.86
18.31
7.39
19.00
The H and K dimensions are defined by the 19 rack mounting kit
5.2.2
Case with rear cover
24

REC 670 ANSI
Section 5
Installing the IED
K
D
xx05000502.vsd
xx05000501.vsd
Figure 3:
Case with rear cover.
Figure 4:
Case with rear cover and

19 rack mounting kit.
xx05000503.vsd
Figure 5:
Case size (mm) A
Rear cover case with

details.
6U, 1/2 x 19
265.9
223.7
242.1
255.8
205.7
190.5
203.7
228.6
6U, 3/4 x 19
265.9
336.0
242.1
255.8
318.0
190.5
316.0
228.6
6U, 1/1 x 19
265.9
448.3
242.1
255.8
430.3
190.5
428.3
465.1
228.6
482.6
The H and K dimensions are defined by the 19 rack mounting kit.
REC 670 ANSI

25
Section 5
Installing the IED
Case size
(inches)
6U, 1/2 x 19
10.47
8.81
9.53
10.07
8.10
7.50
8.02
9.00
6U, 3/4 x 19
10.47
13.23
9.53
10.07
12.52
7.50
12.4
9.00
6U, 1/1 x 19
10.47
17.65
9.53
10.07
16.86
7.50
16.86
18.31
9.00
19.00
The H and K dimensions are defined by the 19 rack mounting kit.
5.2.3
Flush mounting dimensions
A
B
E
D
xx04000465.vsd
Figure 6:
Case size
Tolerance
Flush mounting
Cut-out dimensions (inches)
A
+/0.04
B
+/0.04
6U, 1/2 x 19
8.27
10.01
0.160.39
0.49
6U, 3/4 x 19
12.69
10.01
0.160.39
0.49
6U, 1/1 x 19
17.11
10.01
0.160.39
0.49
E = 188.6 mm without rear protection cover, 229.6 mm with rear protection cover
26

REC 670 ANSI
Section 5
Installing the IED
5.2.4
Side-by-side flush mounting dimensions
xx06000182.vsd
Figure 7:
A 1/2 x 19 size IED 670 side-by-side with RHGS6.
C
xx05000505.vsd
Figure 8:
REC 670 ANSI
Panel-cut out dimensions for side-by-side flush mounting

27
Section 5
Installing the IED
5.2.5
Case size
(inches)
Tolerance
A
0.04
B
0.04
C
0.04
D
0.04
E
0.04
F
0.04
G
0.04
6U, 1/2 x
19
8.42
10.21
9.46
7.50
1.35
0.52
0.25 diam
6U, 3/4 x
19
12.85
10.21
13.89
7.50
1.35
0.52
0.25 diam
6U, 1/1 x
19
17.27
10.21
18.31
7.50
1.35
0.52
0.25 diam
Wall mounting dimensions
A
B
E
en04000471.vsd
Figure 9:
28
Wall mounting

REC 670 ANSI
Section 5
Installing the IED
Case size (inches)
6U, 1/2 x 19
10.50
10.52
10.74
15.36
9.57
6U, 3/4 x 19
15.92
14.94
10.74
15.36
9.57
6U, 1/1 x 19
20.31
19.33
10.74
15.36
9.57
5.3
Mounting methods and details
5.3.1
Mounting the IED

Most of the IED 670s can be rack, flush or wall mounted with the use of different mounting
kits, see figure10. An additional box of type RHGS can be mounted to one side of a 1/2
or 3/4 IED.
The different mounting kits contain all parts needed including screws and assembly
instructions. The following mounting kits are available:
Flush mounting kit

19 Panel (rack) mounting kit
Wall mounting kit
Side-by-side mounting kit
The same mounting kit is used for side-by-side rack mounting and side-by-side flush
mounting.
The mounting kits must be ordered separately when ordering an IED.
They are available as options on the ordering sheet in Accessories for
IED 670, see section 0.
Generally, all the screws included in delivered mounting kits are of Torx type and a
screwdriver of the same type is needed (Tx10, Tx15, Tx20 and Tx25).
If other type of screws are to be used, be sure to use the dimensions of

the screws that are given in this guide.
REC 670 ANSI

29
Section 5
Installing the IED
Figure 10:
Different mounting methods for IED 670
Description
A
Flush mounting
19 Panel rack mounting
C Wall mounting
D Side-by-side rack or flush mounting
5.3.2
Flush mounting
5.3.2.1
Overview
All IED sizes, 1/2 x 19, 3/4 x 19 and 1/1 x 19 and RHGS6 6U 1/4 x 19, cases, can
be flush mounted. Only a single case can be mounted in each cut-out on the cubicle panel,
for class IP54 protection.
The flush mounting kit are utilized for IEDs of sizes: 1/2 x 19, 3/4 x 19 and 1/1 x 19
and are also suitable for mounting of RHGS6, 6U 1/4 x 19 cases.
Flush mounting cannot be used for side-by-side mounted IEDs when IP54
class must be fulfilled. Only IP20 class can be obtained when mounting
two cases side-by-side in one (1) cut-out.
To obtain IP54 class protection, an additional factory mounted sealing

must be ordered when ordering the IED.
30

REC 670 ANSI
Section 5
Installing the IED
5.3.2.2
Mounting procedure for flush mounting

1
7
2
6
5
3
4
xx06000246.vsd
Figure 11:
Flush mounting details.
PosNo
Description
Quantity
Type
Sealing strip, used to

obtain IP54 class. The
sealing strip is factory
mounted between the
case and front plate.
Fastener
Groove
Screw, self tapping
0.11x1.76 inches
Joining point of sealing

strip (rear view)
Panel
Screw
M5x25
Procedure
1.
REC 670 ANSI
Cut an opening in the panel.

31
Section 5
Installing the IED
2.
3.
4.
5.
See section "Flush mounting dimensions" regarding dimensions.

Carefully press the sealing strip around the IEDs collar. Cut the end of the sealing
strip a trifle longer to make the joining point (5) tight.
The sealing strip is delivered with the mounting kit. The strip is long enough for the
largest available IED.
Insert the IED into the opening (cut-out) in the panel.
Attach the fasteners to the IED.
Insert the panel end of the fastener in the gap between the IED and the panel. Insert
the rear end of the fastener into the groove. Insert from the rear side and lightly
tighten the screw (4)
Repeat this with the remaining fasteners.
Fix the IED by tightening all four (7) screws against the panel.
5.3.3
19 panel rack mounting
5.3.3.1
Overview
All IED sizes can be mounted in a standard 19 cubicle rack by using the for each size
suited mounting kit which consists of two mounting angles and fastening screws for the
angles. The mounting angles are reversible which enables mounting of IED size 1/2 x
19 or 3/4 x 19 either to the left or right side of the cubicle.
Please note that the separately ordered rack mounting kit for side-by-side
mounted IEDs, or IEDs together with RHGS cases, is to be selected so
that the total size equals 19.
When mounting the mounting angles, be sure to use screws that follows
the recommended dimensions. Using screws with other dimensions than
the original may damage the PCBs inside the IED.
32

REC 670 ANSI
Section 5
Installing the IED
5.3.3.2
Mounting procedure for 19 panel rack mounting

2
1a
1b
xx04000452.vs d
Figure 12:
19 panel rack mounting details
PosNo
Description
Quantity
Type
1a, 1b
Mounting angels, which can be mounted, either to the left

or right side of the case.
Screw
M4x6
Procedure
1.
2.
3.
REC 670 ANSI
Carefully fasten the mounting angles (1a, 1b) to the sides of the IED.
Use the screws (2) supplied in the mounting kit.
Place the IED assembly in the 19 panel.
Fasten the mounting angles with appropriate screws.

33
Section 5
Installing the IED
5.3.4
Wall mounting
5.3.4.1
Overview
All case sizes, 1/2 x 19, 3/4 x 19 and 1/1 x 19, can be wall mounted. It is also possible
to mount the IED on a panel or in a cubicle.
When mounting the side plates, be sure to use screws that follows the
recommended dimensions. Using screws with other dimensions than the
original may damage the PCBs inside the IED.
If fiber cables are bent too much, the signal can be weakened. Wall
mounting is therefore not recommended for communication modules with
fiber connection; Serial SPA/IEC 60870-5-103 and LON communication
module (SLM), Optical Ethernet module (OEM) and Line data
communication module (LDCM).
5.3.4.2
Mounting procedure for wall mounting

3
4
2
1
5
6
Figure 13:
34
xx04000453.vs d
Wall mounting details.

REC 670 ANSI
Section 5
Installing the IED
PosNo
Description
Quantity
Type
Bushing
Screw
M4x10
Screw
M6x12 or corresponding
Mounting bar
Screw
M5x8
Side plate
Procedure
1.
2.
3.
4.
5.3.4.3
Mount the mounting bars onto the wall (4).

See section "Wall mounting dimensions" for mounting dimensions.
Depending on the wall different preparations may be needed like drilling and
inserting plastic or expander plugs (concrete/plasterboard walls) or threading (metal
sheet wall).
Make all electrical connections to the IED terminal.
It is much easier to do this without the unit in place.
Mount the side plates to the IED.
Mount the IED to the mounting bars.
How to reach the rear side of the IED

The IED can be equipped with a rear protection cover which is recommended to use with
this type of mounting. See figure 14.
To reach the rear side of the IED, a free space of 3.2 inches is required on the unhinged
side.
REC 670 ANSI

35
Section 5
Installing the IED
View from above

3
3.2"
(80 mm)
ANSI_en06000135.vsd
Figure 14:
How to reach the connectors on the rear side of the IED.
PosNo
Description
Type
Screw
M4x10
Screw
M5x8
Rear protection cover
Procedure
1.
2.
3.
Remove the inner screws (1), upper and lower on one side.
Remove all three fixing screws (2), on the opposite side, from wall support.
The IED can now be swung out for access to the connectors, after removing any
rear protection.
5.3.5
Side-by-side 19 rack mounting
5.3.5.1
Overview
IED case sizes, 1/2 x 19 or 3/4 x 19 and RHGS cases, can be mounted side-by-side up
to a maximum size of 19. For side-by-side rack mounting, the side-by-side mounting kit
together with the 19 rack panel mounting kit must be used. The mounting kit has to be
ordered separately.
36

REC 670 ANSI
Section 5
Installing the IED
When mounting the plates and the angles on the IED, be sure to use screws
that follows the recommended dimensions. Using screws with other
dimensions than the original may damage the PCBs inside the IED.
5.3.5.2
Mounting procedure for side-by-side rack mounting

2
1
xx04000456.vsd
Figure 15:
Side-by-side rack mounting details.
PosNo
Description
Quantity
Type
Mounting plate
2, 3
Screw
16
M4x6
Mounting angle
Procedure
1.
2.
3.
4.
5.
6.
7.
REC 670 ANSI
Place the two IEDs next to each other on a flat surface.

Fasten a side-by-side mounting plate (1).
Use four of the delivered screws (2, 3).
Carefully turn the two IEDs up-side down.
Fasten the second side-by-side mounting plate.
Use the remaining four screws.
Carefully fasten the mounting angles (4) to the sides of the IED.
Use the screws available in the mounting kit.
Place the IED assembly in the rack.

37
Section 5
Installing the IED
5.3.5.3
IED 670 mounted with a RHGS6 case

An 1/2 x 19 or 3/4 x 19 size IED can be mounted with a RHGS (6 or 12 depending on
IED size) case. The RHGS case can be used for mounting a test switch of type RTXP 24.
It also has enough space for a terminal base of RX 2 type for mounting of, for example,
a DC-switch or two trip relays.
xx06000180.vsd
Figure 16:
IED 670 (1/2 x 19) mounted with a RHGS6 case containing a test switch
module equipped with only a test switch and a RX2 terminal base.
5.3.6
Side-by-side flush mounting
5.3.6.1
Overview
It is not recommended to flush mount side by side mounted cases if IP54 is required. If
your application demands side-by-side flush mounting, the side-by-side mounting details
kit and the 19 panel rack mounting kit must be used. The mounting kit has to be ordered
separately. The maximum size of the panel cut out is 19.
With side-by-side flush mounting installation, only IP class 20 is
obtained. To reach IP class 54, it is recommended to mount the IEDs
separately. For cut out dimensions of separately mounted IEDs, see
section "Flush mounting".
38

REC 670 ANSI
Section 5
Installing the IED
When mounting the plates and the angles on the IED, be sure to use screws
that follows the recommended dimensions. Using screws with other
dimensions than the original may damage the PCBs inside the IED.
Please contact factory for special add on plates for mounting FT switches
on the side (for 1/2 19" case) or bottom of the relay.
5.3.6.2
Mounting procedure for side-by-side flush mounting

1
3
4
xx06000181.vsd
Figure 17:
Side-by-side flush mounting details (RHGS6 side-by-side with 1/2 x 19

IED).
PosNo
Description
Quantity
Type
Mounting plate
2, 3
Screw
16
M4x6
Mounting angle
Procedure
REC 670 ANSI

39
Section 5
Installing the IED
1.
2.
3.
4.
5.
6.
7.
8.
9.
Make a panel cut-out.

For panel cut out dimension, see section "Side-by-side flush mounting
dimensions".
Carefully press the sealing strip around the IED collar. Cut the end of the sealing
strip little longer to make the joining point tight.
Repeat the same procedure with the second case.
The sealing strip is delivered with the mounting kit. The strip is long enough for the
largest available IED.
Place the two IEDs next to each other on a flat surface.
Fasten a side-by-side mounting plate (1).
Use four of the delivered screws (2, 3).
Carefully turn the two IEDs up-side down.
Fasten the second side-by-side mounting plate.
Use the remaining four screws.
Carefully fasten the mounting angles (4) to the sides of the IED.
Use the fixing screws available in the mounting kit.
Insert the IED into the cut-out.
5.4
Making the electrical connection
5.4.1
IED connectors
5.4.1.1
Overview
The quantity and designation of connectors depend upon the type and size of the IED.
The rear cover plates are prepared with space for the maximum of HW options for each
case size and the cut-outs that are not in use are covered with a plate from factory.
Table 1:
Basic modules, always included
Module
Description
Combined backplane module (CBM)
A backplane PCB that carries all internal signals

between modules in an IED. Only the TRM is not
connected directly to this board.
Universal backplane module (UBM)
A backplane PCB that forms part of the IED backplane

with connectors for TRM, ADM etc.
Power supply module (PSM)
Including a regulated DC/DC converter that supplies

auxiliary voltage to all static circuits.
An internal fail alarm output is available.
40

REC 670 ANSI
Section 5
Installing the IED
Module
Description
Numerical module (NUM)
Module for overall application control. All information is

processed or passed through this module, such as
configuration, settings and communication.
Local Human machine interface (LHMI)
The module consists of LED:s, an LCD, a push button

keyboard and an ethernet connector used to connect a
PC to the IED.
Transformer input module (TRM)
Transformer module that galvanically separates the

internal circuits from the VT and CT circuits. It has 12
analog inputs.
Analog digital conversion module (ADM)
Slot mounted PCB with A/D conversion.
Table 2:
Application specific modules
Module
REC 670 ANSI
Description
Binary input module (BIM)
Module with 16 optically isolated binary inputs
Binary output module (BOM)
Module with 24 single outputs or 12 double-pole

command outputs including supervision function
Binary I/O module (IOM)
Module with 8 optically isolated binary inputs, 10 outputs

and 2 fast signalling outputs.
Line data communication modules (LDCM) (short

range, medium range, long range, X21)
Modules used for digital communication to remote

terminal.
Serial SPA/LON/IEC 60870-5-103

communication modules (SLM)
Used for SPA/LON/IEC 608705103 communication
Optical ethernet module (OEM)
PMC board for IEC 61850 based communication.
mA input module (MIM)
Analog input module with 6 independent, galvanically

separated channels.
GPS time synchronization module (GSM)
Used to provide the IED with GPS time synchronization.
Static output module (SOM)
Module with 6 fast static outputs and 6 change over

output relays.
IRIG-B Time synchronization module
Module with 2 inputs. One is used for handling both

pulse-width modulated signals and amplitude modulated
signals and one is used for optical input type ST for PPS
time synchronization.

41
Section 5
Installing the IED
5.4.1.2
Front side connectors
Figure 18:
IED front side connector
PosNo Description
1
IED serial communication port with RJ45 connector
Ethernet cable with RJ45 connectors
The cable between PC and the IED serial communication port shall be a
crossed-over Ethernet cable with RJ45 connectors. If the connection are
made via a hub or switch, a standard Ethernet cable can be used.
5.4.1.3
Rear side connectors
42

REC 670 ANSI
Section 5
Installing the IED
Table 3:
Designations for 1/2 x 19 casing with 1 TRM slot
Module
Rear Positions
PSM
X11
BIM, BOM, SOM or IOM
X31 and X32 etc. to X51 and

X52
BIM, BOM, SOM, IOM or

GSM
X51, X52
SLM
X301:A, B, C, D
IRIG-B 1)
X302
OEM
X311:A, B, C, D
RS485 or LDCM 2) 3)
X312
LDCM 2)
X313
TRM
X401
1) IRIG-B installation, when included in seat P30:2

2) LDCM installation sequence: P31:2 or P31:3
3) RS485 installation, when included in seat P31:2
Note!
1 One LDCM can be included depending of availability of
IRIG-B respective RS485 modules.
REC 670 ANSI

43
Section 5
Installing the IED
Table 4:
Module
Rear Positions
PSM
X11

MIM
X31 and X32 etc. to

X101 and X102
BIM, BOM, SOM, IOM,

MIM or GSM
X101, X102
SLM
X301:A, B, C, D
IRIG-B or LDCM 1) 2)
X302
LDCM 2)
X303
OEM
X311:A, B, C, D
RS485 or LDCM 2) 3)
X312
LDCM 2)
X313
TRM
X401

2) LDCM installation sequence: P31:2, P31:3, P30:2
and P30:3
Note!
2-4 LDCM can be included depending of availability
of IRIG-B respective RS485 modules.
44

REC 670 ANSI
Section 5
Installing the IED
Table 5:
Module
Rear Positions
PSM
X11

MIM

X72
BIM, BOM, SOM, IOM,

MIM or GSM
X71, X72
SLM
X301:A, B, C, D
IRIG-B or LDCM 1,2)
X302
LDCM 2)
X303
OEM
X311:A, B, C, D
RS485 or LDCM 2) 3)
X312
LDCM 2)
X313
LDCM 2)
X322
LDCM 2)
X323
TRM 1
X401
TRM 2
X411

2) LDCM installation sequence: P31:2, P31:3, P32:2, P32:3,
P30:2 and P30:3
Note!
2-4 LDCM can be included depending of availability of IRIGB respective RS485 modules.
Table 6:
REC 670 ANSI

45
Section 5
Installing the IED
Module
Rear Positions
PSM
X11
BIM, BOM, SOM,

IOM or MIM

X162
BIM, BOM, SOM,

IOM, MIM or GSM
X161, X162
SLM
X301:A, B, C, D
IRIG-B or LDCM
1,2)
X302
LDCM 2)
X303
OEM
X311:A, B, C, D
RS485 or LDCM 2)
3)
X312
LDCM 2)
X313
TRM
X401

2) LDCM installation sequence: P31:2, P31:3, P30:2
and P30:3
Note!
46

REC 670 ANSI
Section 5
Installing the IED
Table 7:
Designations for 1/1 x 19 casing with 2 TRM slots
Module
Rear Positions
PSM
X11
BIM, BOM, SOM,

IOM or MIM

X132
BIM, BOM, SOM,

IOM, MIM or GSM
X131, X132
SLM
X301:A, B, C, D
IRIG-B or LDCM
1,2)
X302
LDCM 2)
X303
OEM
X311:A, B, C, D
RS485 or LDCM 2)
3)
X312
LDCM 2)
X313
LDCM 2)
X322
LDCM 2)
X323
TRM 1
X401
TRM 2
X411

2) LDCM installation sequence: P31:2, P31:3, P32:2,
P32:3, P30:2 and P30:3
Note!
5.4.1.4
Connection diagrams
REC 670 ANSI

47
Section 5
Installing the IED
CT/VT-input designation according to figure 19
Figure 19:
48
Transfo
rmer
input
module
(TRM)
Current/voltage
configuration
(50/60 Hz)
AI0
1
AI
02
AI
03
AI
04
AI
05
AI
06
AI07
AI08
AI09
AI10
AI11
AI12
12I (1A)
1A
1A
1A
1A
1A
1A
1A
1A
1A
1A
1A
1A
12I (5A)
5A
5A
5A
5A
5A
5A
5A
5A
5A
5A
5A
5A
9I (1A) and 3V
1A
1A
1A
1A
1A
1A
1A
1A
1A
110-22
0V
110-22
0V
110-22
0V
9I (5A) and 3V
5A
5A
5A
5A
5A
5A
5A
5A
5A
110-22
0V
110-22
0V
110-22
0V
5I (1A) and 4I (5A)

and 3V
1A
1A
1A
1A
1A
5A
5A
5A
5A
110-22
0V
110-22
0V
110-22
0V
7I (1A) and 5V
1A
1A
1A
1A
1A
1A
1A
110-22
0V
110-22
0V
110-22
0V
110-22
0V
110-22
0V
7I (5A) and 5V
5A
5A
5A
5A
5A
5A
5A
110-22
0V
110-22
0V
110-22
0V
110-22
0V
110-22
0V
6I (1A) and 6V
1A
1A
1A
1A
1A
1A
110-22
0V
110-22
0V
110-22
0V
110-22
0V
110-22
0V
110-22
0V
6I (5A) and 6V
5A
5A
5A
5A
5A
5A
110-22
0V
110-22
0V
110-22
0V
110-22
0V
110-22
0V
110-22
0V
6I (1A)
1A
1A
1A
1A
1A
1A
6I (5A)
5A
5A
5A
5A
5A
5A

REC 670 ANSI
Section 5
Installing the IED
Figure 21:
Figure 20:
REC 670 ANSI
mA input module (MIM)
Binary input module (BIM).

Input contacts named XA
corresponds to rear position
X31, X41, etc. and input
contacts named XB to rear
position X32, X42, etc.

49
Section 5
Installing the IED
Figure 22:
Communication interfaces (OEM, LDCM, SLM and HMI)
Note to figure 22
1)
Rear communication port SPA/IEC 61850-5-103, ST-connector for glass alt. HFBR Snap-in connector for plastic as ordered
2)
Rear communication port LON, ST connector for glass alt. HFBR Snap-in connector for plastic as ordered
3)
Rear communication port RS485, terminal block
4)
Time synchronization port IRIG-B, BNC-connector
5)
Time synchronization port PPS or Optical IRIG-B, ST-connector
6)
Rear communication prot IEC 61850, ST-connector
7)
Rear communication port C37.94, ST-connector
8)
Front communication port Ethernet, RJ45 connector
9)
Rear communication port 15-pole female micro D-sub, 1.27 mm (0.050") pitch
10)
Rear communication port, terminal block
50

REC 670 ANSI
Section 5
Installing the IED
Figure 24:
GPS time synchronization module (GSM)
Figure 23:
Power supply module (PSM)
Figure 25:
Binary output module (BOM). Output contacts named XA corresponds to rear position X31, X41,
etc. and output contacts named XB to rear position X32, X42, etc.
REC 670 ANSI

51
Section 5
Installing the IED
Figure 26:
52
Static output module (SOM)

REC 670 ANSI
Section 5
Installing the IED
Figure 27:
Binary in/out module (IOM). Input contacts named XA corresponds to rear position X31, X41, etc. and
output contacts named XB to rear position X32, X42, etc.
5.4.1.5
Connection examples
WARNING! USE EXTREME CAUTION! Dangerously high voltages
might be present on this equipment, especially on the plate with resistors.
Do any maintenance ONLY if the primary object protected with this
equipment is de-energized. If required by national low/standard enclose
the plate with resistors with a protective cover or in a separate box!
Connections for three-phase high impedance differential protection
Generator, reactor or busbar differential protection is a typical application for three-phase

high impedance differential protection. Typical CT connections for three-phase high
impedance differential protection scheme with 670 series are shown in figure CT
connections for High Impedance Differential Protection
REC 670 ANSI

53
Section 5
Installing the IED
L1
(A)
L2
(B)
L3
(C)
7
1
CT 1200/1
Star/Wye
Connected
AI01 (I)
2
3
AI02 (I)
4
5
AI03 (I)
6
7
AI04 (I)
10
AI05 (I)
10
11
AI06 (I)
12
IED 670
Protected Object
N
L3 (C)
L2 (B)
L1 (A)
N
L3 (C)
L2 (B)
CT 1200/1
Star/Wye
Connected
L1 (A)
X1
11
12
13
14
Figure 28:
54
L2
(B)
L3
(C)
1
3
4
R3
1
3
4
R2
1
3
R1
4
2
1
2 U
1
R6
2 U
R5
R4
L1
(A)
2 U
3-Ph Plate with Metrosils and Resistors
CT connections for High Impedance Differential Protection
Number 1 shows the scheme earthing point. Note that it is of outmost importance to
insure that only one earthing point exist in such scheme.
Number 2 shows the three-phase plate with setting resistors and metrosils.
Number 3 shows the necessary connection for three-phase metrosil set. Shown
connections are applicable for both types of three-phase plate.
Number 4 shows the position of optional test switch for secondary injection into the
high impedance differential relay.
Number 5 shows the necessary connection for setting resistors. Shown connections
are applicable for both types of three-phase plate.
Number 6 shows that the factory made star point on a three-phase setting resistor set
shall be removed for installations with 670 series. This star point is required for
RADHA schemes only!
Number 7 shows how to connect three individual phase currents for high impedance
scheme to three CT inputs in IED 670.
Number 8 shows a TRM module where these current inputs are located. Note that
the CT ratio for high impedance differential protection application must be set as
one! Thus for main CTs with 1A secondary rating the following setting values shall
be entered: CTprim=1A and CTsec=1A; while for main CTs with 5A secondary

REC 670 ANSI
Section 5
Installing the IED
rating the following setting values shall be entered: CTprim=5A and CTsec=5A. The
parameter CTStarPoint shall be always left to the default value ToObject.
Number 9 shows three connections made in Signal Matrix Tool (i.e. SMT) which
connect these three current inputs to first three input channels of the preprocessing
function block (10). For high impedance differential protection preprocessing
function block in 3ms task shall be used.
Number 10 shows the preprocessing block which has a task to digitally filter the
connected analogue inputs. Preprocessing block outputs AI1, AI2 and AI3 shall be
connected to three instances of high impedance differential protection function
blocks (e.g. HZD1, HZD2 and HZD3 function blocks in the configuration tool).
Connections for three-phase high impedance differential protection
Restricted earth fault (REF) protection is a typical application for one-phase high
impedance differential protection. Typical CT connections for high impedance based
REF protection scheme with 670 series are shown in figure CT connections for Restricted
Earth Fault Protection
L1
(A)
L2
(B)
L3
(C)
7
1
CT 1500/5
Star/Wye
Connected
AI01 (I)
2
3
AI02 (I)
4
5
AI03 (I)
6
7
AI04 (I)
8
9
AI05 (I)
10
11
Protected Object
L1
(A)
L2
(B)
AI06 (I)
12
L3
(C)
IED 670
4
1
CT 1500/5
X1
Figure 29:
REC 670 ANSI
3
4
R2
R1
en07000194.vsd
2 U
1-Ph Plate with Metrosil and Resistor
CT connections for Restricted Earth Fault Protection

55
Section 5
Installing the IED
5.4.2
Number 1 shows the scheme earthing point. Note that it is of outmost importance to
insure that only one earthing point exist in such scheme.
Number 2 shows the one-phase plate with setting resistor and metrosil.
Number 3 shows the necessary connection for the metrosil. Shown connections are
applicable for both types of one-phase plate. Number 4 shows the position of
optional test switch for secondary injection into the high impedance differential relay.
Number 4 shows the position of optional test switch for secondary injection into the
high impedance differential relay.
Number 5 shows the necessary connection for setting resistor. Shown connections
are applicable for both types of one-phase plate.
Number 6 shows how to connect the REF high impedance scheme to one CT input
in IED 670.
Number 7 shows a TRM module where this current input is located. Note that the
CT ratio for high impedance differential protection application must be set as one!
Thus for main CTs with 1A secondary rating the following setting values shall be
entered: CTprim=1A and CTsec=1A; while for main CTs with 5A secondary rating
the following setting values shall be entered: CTprim=5A and CTsec=5A. The
parameter CTStarPoint shall be always left to the default value ToObject.
Number 8 shows a connection made in Signal Matrix Tool (i.e. SMT) which connects
this current input to first input channel of the preprocessing function block (10). For
high impedance differential protection preprocessing function block in 3ms task shall
be used.
Number 9 shows the preprocessing block which has a task to digitally filter the
connected analogue inputs. Preprocessing block output AI1 shall be connected to
one instances of high impedance differential protection function block (e.g. HZD1
function block in the configuration tool).
Connecting to protectiveground
Connect the grounding screw (pos 1 in figure 30) on the rear of the IED unit to the closest
possible earthing point in the cubicle. Electrical codes and standards require that
protective ground cables are green/yellow conductors with a cross section area of at least
2.5 mm2 (AWG14). There are several protective grounding screws on an IED. The Power
supply module (PSM), Transformer input modules (TRM) and the enclosure are all
separately grounded, see figure 30 below.
The cubicle must be properly connected to the station earthinggrounding system. Use a
conductor with a core cross section area of at least 4 mm2 (AWG 12).
56

REC 670 ANSI
Section 5
Installing the IED
3
1
en05000509.vsd
Figure 30:
Rear view of IED with one TRM showing grounding points.
PosNo Description
1
Main protective ground to chassis
2
3
Grounding screw to Transformer input module (TRM). (There is one ground connection per TRM)
Use the main protective ground screw (1) for connection to the stations
grounding system. Grounding screws for PSM module (2) and TRM
module (3) must be fully tightened to secure protective ground connection
of these modules.
5.4.3
Connecting the power supply module

The wiring from the cubicle terminal block to the IED terminals (see figure 23 for PSM
connection diagram) must be made in accordance with the established guidelines for this
type of equipment. The wires from binary inputs and outputs and the auxiliary supply
must be routed separated from the current transformer cables between the terminal blocks
of the cubicle and the IEDs connections. The connections are made on connector X11.
For location of connector X11, refer to section "Rear side connectors".
5.4.4
Configuration for analog CT inputs

The secondary rated current of the CT (i.e. 1A or 5A) determines the choice of TRM in
the IED. Two TRMs are available, One is dimensioned for an input current of 5A and the
REC 670 ANSI

57
Section 5
Installing the IED
other for an input of 1A. If the CT rated secondary current does not match the TRM input
current rating adjustments can be made in settings depending on the tolerance of the TRM.
5.4.5
Connecting to CT and VT circuits

CTs and VTs are connected to the 24pole connector of the Transformer input module
(TRM) on the rear side of the IED. Connection diagram for TRM is shown in figure 19.
Use a solid conductor with a cross section area between 2.5-6 mm2 (AWG14-10) or a
stranded conductor with a cross section area between 2.5-4 mm2 (AWG14-12).
If the IED is equipped with a test-switch of type RTXP 24 COMBIFLEX wires with 20
A sockets must be used to connect the CT and VT circuits.
Connectors X401 and X402 (for location see section "Rear side connectors") for current
and voltage transformer circuits are so called feed-through terminal blocks and are
designed for conductors with cross sectional area up to 4 mm2 (AWG 12). The screws
used to fasten the conductors should be tightened with a torque of 1Nm.
Figure 31:
58
Examples of ringlug
terminals
Figure 32:

Exaples of standard
compression connection
terminals
REC 670 ANSI
Section 5
Installing the IED
5.4.6
Connecting the binary input and output signals

Auxiliary power and signals are connected using voltage connectors. Signal wires are
connected to a female connector, see figure 33, which is then plugged into the
corresponding male connector, see figure 34, located at the rear of the IED. For location
of BIM, BOM, IOM and SOM refer to section "Rear side connectors". Connection
diagrams for BIM, BOM, IOM and SOM are shown in figure 20, figure 25, figure26 and
figure 27.
If the IED is equipped with a test-switch of type RTXP 24 COMBIFLEX wires with 20
A sockets, 1.5mm (AWG16) conductor area must be used to connect the auxiliary power.
Procedure
1.
2.
3.
Connect signals to the female connector

All wiring to the female connector should be done before it is plugged into the male
part and screwed to the case. The conductors can be of rigid type (solid, stranded)
or of flexible type.
The female connectors accept conductors with a cross section area of 0.2-2.5
mm2 (AWG 24-14). If two conductors are used in the same terminal, the maximum
permissible cross section area is 0.2-1 mm2 (AWG 24-18 each).
If two conductors, each with area 1.5 mm2 (AWG 16) need to be connected to the
same terminal, a ferrule must be used, see figure 35. This ferrule, is applied with
the by Phoenix recommended crimping tool, see figure "". No soldering is needed.
Wires with a smaller gauge can be inserted directly into the female connector
receptacle and the fastening screw shall be tightened with a torque of 0.4 Nm (This
torque applies to all binary connectors).
Plug the connector to the corresponding back-side mounted male connector
Lock the connector by fastening the lock screws
xx02000742.vsd
Figure 33:
REC 670 ANSI
A female connector

59
Section 5
Installing the IED
Figure 34:
Board with male connectors
1
2
xx06000168.vsd
Figure 35:
Cable connectors
PosNo Description
5.4.7
Is ferrule,
A bridge connector, is used to jump terminal points in a connector.
Making the screen connection

When using screened cables always make sure screens are grounded and connected
according to applicable engineering methods. This may include checking for appropriate
grounding points near the IED, for instance, in the cubicle and/or near the source of
measuring. Ensure that ground connections are made with short (max. 10 cm) conductors
of an adequate cross section, at least 6 mm2 (AWG10) for single screen connections.
60

REC 670 ANSI
Section 5
Installing the IED
3
Lc
Cc
Lc
Rx
Tx
IED
Tx
Rx
Sc
Sc
Figure 36:
External
Equipment
en06000190.vsd
Communication cable installation.
PosNo Description
1
Outer shield
Protective ground screw
Inner shield
Inner shielding of the cable shall be grounded at the external equipment

end only. At the Relay terminal end, the inner shield must be isolated from
protective ground.
5.5
Optical connections
5.5.1
Connecting station communication interfaces (OEM and SLM)

The IED can, if ordered accordingly, be equipped with an optical ethernet module (OEM,
see figure 22), needed for IEC 61850 communication and a serial communication module
(SLM, see figure 22) for LON, SPA and IEC 608705103 communication. In such cases
optical ports are provided on the rear side of the case for connection of the optical fibers.
For location of OEM and SLM, refer to section "Rear side connectors".
REC 670 ANSI
Optical ports X311: A, B (Tx, Rx) and X311: C, D (Tx, Rx) on the OEM module are
used for IEC 61850 communication. Connectors are of ST type. When the optical

61
Section 5
Installing the IED
ethernet module is used, the protection plate for the galvanic connection must not be
removed.
Optical port X301: A, B (Tx, Rx) on the SLM module is used for SPA or IEC
60870-5-103 communication. Connectors are of ST type (glass) or HFBR Snap in
(plastic).
Optical port X301: C, D (Tx, Rx) on the SLM module is used for LON
communication. Connectors are of ST type (glass) or HFBR Snap in (plastic).
Connectors are generally color coded; connect blue or dark grey cable connectors to blue
or dark grey (receive) back-side connectors. Connect black or grey cable connectors to
black or grey (transmit) back-side connectors.
The fiber optical cables are very sensitive to handling. Do not bend too
sharply. The minimum curvature radius is 15 cm for the plastic fiber
cables and 25 cm for the glass fiber cables. If cable straps are used to fix
the cables, apply with loose fit.
Always hold the connector, never the cable, when connecting or
disconnecting optical fibers. Do not twist, pull or bend the fiber. Invisible
damage may increase fiber attenuation thus making communication
impossible.
Please, strictly follow the instructions from the manufacturer for each type
of optical cables/connectors.
5.5.2
Connecting remote communication interfaces (LDCM)

The Line Data Communication Module (LDCM, see figure 22) is the hardware used for
the transfer of binary and analog signal data between IEDs in different protection schemes
on the IEEE/ANSI C37.94 protocol. The optical ports on the rear side of the IED are
X302, X303, X312 and X313. For location of LDCM module, refer to section "Rear side
connectors".
62

REC 670 ANSI
Section 5
Installing the IED
5.6
Galvanic X.21 line data communication (X.21LDCM)
5.6.1
Connecting Galvanic X.21 line data communication module (X.

21 LDCM)
The Galvanic X.21 line data communication module (X.21 LDCM, see figure 22) is the
hardware used for the transfer of binary and analog signal data between IEDs in different
protection schemes via telecommunication equipment, for example leased telephone
lines. For location of X-21 LDCM module, refer to section "Rear side connectors".
The galvanic X.21 line data communication module uses a ABB specific PC*MIP Type
II format.
en07000196.vsd
Figure 37:
REC 670 ANSI
Overview of the X.21 LDCM module

63
Section 5
Installing the IED
en07000195.vsd
Figure 38:
1.
2.
3.
The X.21 LDCM module external connectors
Ground selection connector for IO, screw terminals, 2-pole

Ground pin
X.21: Micro D-sub 15 pole female connector according to the V11 (X.27) balanced
version
Soft ground
To avoid ground loops when the grounds are connected, a soft ground connection for the
IO-ground can be used. This is handled in the ground selection connector.
Three different kinds of grounding principles can be set:
1.
2.
3.
No ground - leave the connector without any connection

Direct ground - connect the ground pin directly to earth
Soft ground - connect the two pins to each other
X.21 connector
Table 8:
Pinout for the X.21 communication connector
Pin number
Signal
Shield (ground)
TXD A
Control A
RXD A
Signal timing A
Ground
TXD B
10
Control B
64

REC 670 ANSI
Section 5
Installing the IED
11
RXD B
13
Signal timing B
5,7,12,14,15
Not used
5.7
Installing the serial communication cable for

RS485
5.7.1
RS485 serial communication module

Angle
bracket
Screw
terminal
X3
Screw
terminal
X1
1
2
1
2
3
4
5
6
RS485
PWB
Backplate
en07000140.vsd
Figure 39:
Pin
The connection plate to the backplate with connectors and screws. This
figure also shows the pin numbering from the component side
Name 2-wire
Name 4-wire
Description
x3:1
soft ground
x3:2
soft ground
x1:1
RS485 +
TX+
Receive/transmit high or
transmit high
x1:2
RS485
TX-
Receive/transmit low or
transmit low
x1:3
Term
T-Term
Termination resistor for

transmitter (and receiver
in 2-wire case) (connect
to TX+)
x1:4
reserved
R-Term
Termination resistor for

receiver (connect to RX
+)
REC 670 ANSI

65
Section 5
Installing the IED
Pin
Name 2-wire
Name 4-wire
Description
x1:5
reserved
RX-
Receive low
x1:6
reserved
RX+
Receive high
2wire:
Connect pin X1:1 to pin

X1:6 and pin X1:2 to pin
X1:5.
Termination (2-wire):

X1:3
Termination (4-wire):

X1:3 and pin X1:4 to pin
X1:6
The distance between earth points should be < 1200 m (3000 ft), see figure 40 and 41.
Only the outer shielding is connected to the protective earth at the terminal. The inner
and outer shieldings are connected to the protective earth at the external equipment. Use
insulating tape for the inner shield to prevent contact with the protective earth. Make sure
that the terminals are properly earthed with as short connections as possible from the earth
screw, for example to an earthed frame.
The terminal and the external equipment should preferably be connected to the same
battery.
Cc
1 2 3 4 5 6
Cc
1)
2)
1 2 3 4 5 6
X1
X1
IED
External
Equipment (PC)
IED
PG
PG
PG
PG 1) 3)
Figure 40:
en07000141_ansi.vsd
Communication cable installation, 2-wire.
Where:
66

REC 670 ANSI
Section 5
Installing the IED
The inner shields shall be connected together (with an isolated terminal block) and only have one
grounding point in the whole system, preferably at the external equipment (PC).
The outer shield shall be connected to Protective Ground (PG) in every cable end i.e. to PG at all
relay terminals and to PG at External equipment (PC). The first terminal will have only one cable
end but all others of course two.
Connect according to installation instructions for the actual equipment, observe the 120 ohms
termination.
The protective ground should be close to the external equipment (< 2m)
Cc
Communication cable
PE
Protective earth screw
Cc
Cc
1)
1)
1 2 3 4 5 6
2)
1 2 3 4 5 6
X1
X1
IED
External
Equipment (PC)
IED
PG
PG
PG
PG 1) 3)
Figure 41:
en07000142_ansi.vsd
Communication cable installation, 4-wire.
Where:
REC 670 ANSI
The inner shields shall be connected together (with an isolated terminal block) and only have one
grounding point in the whole system, preferably at the external equipment (PC).
The outer shield shall be connected to Protective Ground (PG) in every cable end i.e. to PG at all
relay terminals and to PG at External equipment (PC). The first terminal will have only one cable
end but all others of course two.
Connect according to installation instructions for the actual equipment, observe the 120 ohms
termination.
The protective ground should be close to the external equipment (< 2m)
Cc
Communication cable

67
Section 5
Installing the IED
PG
Protective ground screw
en03000110.vsd
Figure 42:
Cable contact, Phoenix: MSTB2.5/6-ST-5.08 1757051
Where:
1
is cable
is screw
Pair separator
Pair Shield
Drain wire
Conductor
Overall shield
Separator
Jacket
en07000139.vsd
Figure 43:
Cross section of communication cable
The EIA standard RS-485 specifies the RS485 network. An informative excerpt is given
in section "Installing the serial communication cable for RS485 SPA/IEC".
68

REC 670 ANSI
Section 5
Installing the IED
5.7.2
Installing the serial communication cable for RS485 SPA/IEC

Informative excerpt from EIA Standard RS-485 - Electrical Characteristics of Generators
and Receivers for Balanced Digital Multipoint Systems
RS-485 Wire - Media dependent Physical layer
1
Normative references
EIA Standard RS-485 - Electrical Characteristics of Generators and Receivers for Balanced Digital
Multipoint Systems
2
Transmission method
RS-485 differential bipolar signaling

2.1
Differential signal levels
Two differential signal levels are defined:

A+ =line A positive with respect to line B
A- =line A negative with respect to line B
2.2
Galvanic isolation
The RS485 circuit shall be isolated from earth by:

Riso 10 MW
Ciso 10 pF
Three isolation options exist:
a) The entire node electronics can be galvanically isolated
b) The bus interface circuit can be isolated form the rest of node electronics by optoisolators,
transformer coupling or otherwise.
c) The RS485 chip can include built-in isolation
2.3
Bus excitation and signal conveyance
2.3.1
Requirements
a) The RS485 specification requires the Signal A and Signal B wires.
b) Each node also requires (5 V) Excitation of the RS485 termination network.
c) Vim - the common mode voltage between any pair of RS485 chips may not exceed 10 V.
d) A physical ground connection between all RS485 circuits will reduce noise.
2.3.2
Bus segment termination network
The termination network below required at each end of each Bus Ph-segment.
REC 670 ANSI

69
Section 5
Installing the IED
ExV+
Ru = 390 ohm
1/4 W, 2%
Signal B
Rt = 220 ohm
1/4 W, 2%
Signal A
Rd = 390 ohm
1/4 W, 2%
DGND
ExV is supplied by the Node at end of the Bus Segment
en03000112.vsd
Figure 44:
RS-485 bus segment termination
ExV is supplied by the Node at end of the Bus Segment

The specifications of the components are:
2.3.3
a) Ru
+ 5 V to Signal B
= 390 W, 0.25 W 2.5%
b) Rt
Signal B to Signal A
= 220 W, 0.25 W 2.5%
c) Rd
Signal A to GND
= 390 W, 0.25 W 2.5%
Bus power distribution
The end node in each Ph-segment applies 5 V bus excitation power to the Termination network via
the Excitation pair (ExV+ and GND) used in the Type 3 Physical layer specification.
5.7.3
70
Data on RS485 serial communication module cable

Type:
Twisted-pair S-STP (Screened Screened Twisted Pair)
Shield:
Individual foil for each pair with overall copper braid
Length:
Maximum 1200 m (3000 ft) from one system earth to the next system earth (includes
length from platform point to system earth on both sides)
Temp:
According to application
Impedance:
120 W
Capacitance:
Less than or equal to 42 pF/m
Example:
Belden 9841,Alpha wire 6412, 6413

REC 670 ANSI
Section 5
Installing the IED
5.8
Installing the GPS antenna
5.8.1
Installing the GPS antenna
5.8.1.1
Antenna installation
The antenna is mounted on a console for mounting on a horizontal or vertical flat surface
or on an antenna mast.
2
3
xx05000510.vsd
Figure 45:
GPS antenna and mounting accessories
PosNO Description
REC 670 ANSI
GPS antenna
TNC connector
Console, mm3.07x5.9 inches
Mounting holes 0.22 inches
Tab for securing of antenna cable
Vertical mounting position (on antenna mast etc.)
Horizontal mounting position

71
Section 5
Installing the IED
Mount the antenna and console clear of flat surfaces such as buildings walls, roofs and
windows to avoid signal reflections. If necessary, protect the antenna from animals and
birds which can affect signal strength. Also protect the antenna against lightning.
Always position the antenna and its console so that a continuous clear line-of-sight
visibility to all directions is obtained, preferably more than 75%. A minimum of 50%
clear line-of-sight visibility is required for un-interrupted operation.
99001046.vsd
Figure 46:
5.8.1.2
Antenna line-of-sight
Electrical installation
Use a 50 ohm coaxial cable with a male TNC connector on the antenna end and a male
SMA connector on the receiver end to connect the antenna to IED 670. Choose cable type
and length so that the total attenuation is max. 26 dB at 1.6 GHz. A suitable antenna cable
can be supplied with the antenna.
The antenna has a female TNC connector to the antenna cable. For location of GPS
module, refer to section "Rear side connectors". Connection diagram for GPS module is
shown in figure 24.
Make sure that the antenna cable is not charged when connected to the
antenna or to the receiver. Discharge the antenna cable by short-circuiting
the end of the antenna cable with some metal device and then connect it
to the antenna. When the antenna is connected to the cable, connect the
72

REC 670 ANSI
Section 5
Installing the IED
cable to the receiver. IED 670 must be switched off when the antenna
cable is connected.
REC 670 ANSI

73
74
Section 6
Checking the external optical and electrical connections
Section 6
Checking the external optical and

electrical connections
About this chapter
This chapter describes what to check to ensure correct connection to the external circuitry,
such as the auxiliary power supply, CTs and VTs. These checks must be made with the
protection IED de-energized.
6.1
Overview
The user must check the installation which includes verifying that the IED is connected
to the other parts of the protection system. This is done with the IED and all connected
circuits de-energized.
6.2
Checking the VT circuits

Check that the wiring is in strict accordance with the supplied connection diagram.
Do not continue before any errors are corrected.
Test the circuitry. The following tests are recommended:
Polarity check.
VT circuit voltage measurement (primary injection test).
Grounding check.
Phase relationship
Insulation resistance check
The polarity check verifies the integrity of circuits and the phase relationships. The check
should be performed as close as possible to the IED.
The primary injection test verifies the VT ratio and the wiring all the way through from
the primary system to the IED. Injection must be performed for each phase-to-neutral
REC 670 ANSI

75
Section 6
circuit and each phase-to-phase pair. In each case voltages in all phases and neutral are
measured.
6.3
Check of CT circuits
The CTs must be connected in accordance with the circuit diagram provided with the
IED, both with regards to phases and polarity. The following tests shall be performed on
every primary CT connected to the IED 670:
primary injection test to verify the current ratio of the CT, the correct wiring up to
the protection IED and correct phase sequence connection (i.e. A, B, C)
polarity check to prove that the predicted direction of secondary current flow is
correct for a given direction of primary current flow. This is an essential test for the
proper operation of the differential function.
CT secondary loop resistance measurement in order to confirm that the current
transformer secondary loop dc resistance is within specification and that there are
no high resistance joints in the CT winding or wiring.
CT excitation test in order to confirm that the current transformer is of the correct
accuracy rating and that there are no shorted turns in the current transformer
windings. Manufacturer's design curves should be available for the current
transformer in order to compare the actual results.
check the grounding of the individual CT secondary circuits to verify that each threephase set of main CTs is properly connected to the station ground and only at one
electrical point.
Insulation resistance check.
Phase identification of CT shall be made.
Both primary and secondary sides must be disconnected from the line and
IED when plotting the excitation characteristics.
If the CT secondary circuit ground connection is removed without the

current transformer primary being de-energized, dangerous voltages may
result in the secondary CT circuits.
76

REC 670 ANSI
Section 6
6.4
Checking the power supply

Check that the auxiliary supply voltage remains within the permissible input voltage range
under all operating conditions. Check that the polarity is correct.
6.5
Checking the binary I/O circuits
6.5.1
Binary input circuits

Preferably, disconnect the binary input connector from the binary input cards. Check all
connected signals so that both input level and polarity are in accordance with the IEDs
specifications.
6.5.2
Binary output circuits

Preferably, disconnect the binary output connector from the binary output cards. Check
all connected signals so that both load and polarity are in accordance with IED
specifications.
6.6
Checking the optical connections

Check that the Tx and Rx optical connections are correct.
REC 670 ANSI

77
78
Section 7
Energizing the IED
Section 7
Energizing the IED

About this chapter
This chapter describes the start up sequence and what to check once the IED has been
energized.
7.1
Overview
Before the procedures in this chapter can be carried out the connection to external circuitry
must have been checked which ensures that the installation was made correctly.
The user could also check the software version, the IEDs serial number and the installed
modules and their ordering number to ensure that the IED is according to delivery and
ordering specifications. The user must energize the power supply of the IED to start it
up. This could be done in number of ways, from energizing a whole cubicle to energizing
a single IED. The user should reconfigure the IED to activate the hardware modules in
order to enable the self supervision function to detect possible hardware errors. Then the
IED time must be set. The self supervision function (Diagnostics in HMI) should also be
checked to verify that the IED unit operates properly.
7.2
Energizing the IED

When the IED is energized, the green LED instantly starts flashing. After approximately
55 seconds the window lights up and the window displays IED Startup. The main menu
is displayed and the upper row should indicate Ready after about 90 seconds. A steady
green light indicates a successful startup.
1
55
90
t (s)
xx04000310.vsd
Figure 47:
Typical IED startup sequence
1 IED energized. Green Light Emitting Diode (LED) starts flashing

2 LCD lights up and "IED startup" is displayed
REC 670 ANSI

79
Section 7
Energizing the IED
3 The main menu is displayed. A steady green light indicates a successful startup.
If the upper row in the window indicates Fail instead of Ready and the green LED
flashes, an internal failure in the IED has been detected. See section 3.3 "Checking the
self supervision function" in this chapter to investigate the fault.
An example of the local HMI with a small LCD is shown in figure 48.
The different parts of the medium size LHMI is shown in figure 48The LHMI, exists in
an IEC version and in an ANSI version. The difference is on the keypad operation buttons
and the yellow LED designation.
80

REC 670 ANSI
Section 7
Energizing the IED
REC 670 ANSI

81
Section 7
Energizing the IED
Figure 48:
Medium size graphic HMI
1 Status indication LEDs

2 LCD
3 Indication LEDs
4 Label
5 Local/Remote LEDs
6 RJ45 port
7 Communication indication LED
8 Keypad
7.3
Checking the self supervision signals
7.3.1
Reconfiguring the IED

I/O modules configured as logical I/O modules (BIM, BOM or IOM) are supervised.
I/O modules that are not configured are not supervised.
Each logical I/O module has an error flag that indicates signal or module failure. The
error flag is also set when the physical I/O module of the correct type is not detected in
the connected slot.
7.3.2
Setting the IED time

This procedure describes how to set the IED time from the local HMI.
1.
2.
3.
82
Display the set time dialog.

Navigate to:
Settings/Time/System time
Press the E button to enter the dialog.
Set the date and time.
Use the Left and Right arrow buttons to move between the time and date values
(year, month, day, hours, minutes and seconds). Use the Up and Down arrow buttons
to change the value.
Confirm the setting.
Press the E button to set the calendar and clock to the new values.

REC 670 ANSI
Section 7
Energizing the IED
7.3.3
Checking the self supervision function
7.3.3.1
Determine the cause of an internal failure

This procedure describes how to navigate the menus in order to find the cause of an
internal failure when indicated by the flashing green LED on the HMI module.
Procedure
1.
2.
7.3.4
Display the general diagnostics menu.

Navigate the menus to:
Diagnostics/IED status/General
Scroll the supervision values to identify the reason for the failure.
Use the arrow buttons to scroll between values.
Self supervision HMI data

Table 9:
Signals from the General menu in the diagnostics tree.
Indicated result
Possible reason
Proposed action
InternFail OK
No problem detected.
None.
InternFail Fail
A failure has occurred.
Check the rest of the indicated results to find the

fault.
InternWarning OK
None.
InternWarning Warning
A warning has been

issued.
Check the rest of the indicated results to find the

fault.
NUM-modFail OK
None.
NUM-modFail Fail
The main processing

module has failed.
Contact your ABB representative for service.
NUM-modWarning OK
None.
NUM-modWarning
Warning
There is a problem with:
Set the clock.

If the problem persists, contact your ABB
representative for service.
ADC-module OK
None.
ADC-module Fail
The AD conversion
module has failed.
Contact your ABB representative for service.
CANP 9 BIM1 Fail
IO module has failed.
Check that the IO module has been configured and

connected to the IOP1- block.
RealTimeClock OK
None.
the real time clock.

the time
synchronization.
REC 670 ANSI

83
Section 7
Energizing the IED
Indicated result
84
Possible reason
Proposed action
RealTimeClock Warning
The real time clock has

been reset.
Set the clock.
TimeSync OK
None.
TimeSync Warning
No time synchronization.
Check the synchronization source for problems.


REC 670 ANSI
Section 8
Set up PCM 600 communication link per IED
Section 8
Set up PCM 600 communication link

per IED
About this chapter
This chapter describes the communication between the IED and the PCM 600.
8.1

The communication between the IED and the PCM 600 is independent of the used
communication protocol within the substation or to the NCC. It can be seen as a second
channel for communication.
The communication media is always Ethernet and the used protocol is TCP/IP.
Each IED 670 product has an Ethernet front connector for PCM 600 access. Depending
very much on the station concept and the used station protocol additional Ethernet
interfaces may be available on the rear side of the IED 670. All Ethernet interfaces can
be used to connect PCM 600.
When an Ethernet based station protocol is used the PCM 600 communication can use
the same Ethernet port and IP address. The IED 670 is able to separate the information
belonging to the PCM 600 dialog.
For the connection of the PCM 600 to the IED two basic variants have to be considered.
direct point to point link between PCM 600 and the IED 670
indirect link via a station LAN or from remote via a network
The communication procedures are in both cases the same.

The physical connection and the IP-addresses must be configured in both cases before a
dialog can start. The steps to do this are:
REC 670 ANSI
Set up or get the IP-addresses of the IED 670s

Set up the PC or workstation for a direct link or

85
Section 8
in this case get a special null-modem cable (Rx, Tx cross-wired) for the direct
link between PCM 600 and IED 670
Connect the PC or workstation to the network

Configure the IED 670 IP-addresses in the PCM 600 project for each IED these are
used by the OPC interface of PCM 600 for communication
IP addresses of IED 670 products

The IP address and the corresponding mask can be set only via the local HMI for each
available Ethernet interface in the IED 670. Each Ethernet interface has a default address
ex factory when the complete IED 670 is delivered. This is not given when an additional
Ethernet interface is installed or an interface is replaced.
The rules etc. for the configured IP addresses are part of the project.
Point to point link

A special cable is requested to connect two physical Ethernet interfaces together without
a HUB, router, bridge, switch etc. between. The Tx and Rx signal wires must be crossed
in the cable to connect Tx with Rx on the other side and vice versa. These cables are
known as null-modem cable or cross-wired cable. The minimum length should be about
2 m. The connector type is RJ45.
IED670
RJ45
PCM600
Tx
Tx
Rx
Rx
en05000810.vsd
Figure 49:
Point to point link between IED 670 and PCM 600 using a null-modem
cable
Set up a PC for a direct link

The following description is an example valid for standard PCs using Microsoft Windows
operating system . The example is taken from a Laptop with one Ethernet interface.
The procedure is as follows:
86

REC 670 ANSI
Section 8
1.
2.
3.
4.
5.
select the Local Area Connection

select Properties in the shown status window
select the TCP/IP protocol from the list of configured components using this
connection and open Properties
choose Use the following IP address and type in an IP address and Subnet mask
which you can define. Make sure that you are outside the range of addresses used by
the IED 670s.
close all open windows and start PCM 600
Remark
Administrator rights are requested to change the configuration as described above.
en05000812.vsd
Figure 50:
REC 670 ANSI
Step 1: select the Local Area Connection

87
Section 8
en05000813.vsd
Figure 51:
Step 2: select Properties in the status window
en05000814.vsd
Figure 52:
88
Step 3: select the TCP/IP protocol and open Properties

REC 670 ANSI
Section 8
en05000815.vsd
Figure 53:
Step 4: specify a TCP/IP address and Subnet mask for the PC
Set up the PC to access the IED 670 via a network

This task is very much dependent on the used LAN/WAN network. A description of how
this is done is beyond the scope of this manual..
Enter IED 670 IP-address in the project

There are two ways of entering the given IP-address of an IED 670 in a project which is
used by PCM 600 to communicate with the IED 670.
1.
2.
REC 670 ANSI
via the first window of the wizard by including a new IED 670 in a project
by entering the IP-address of the IED 670 in the Object Properties window

89
Section 8
select the IED to enter the IP-address

open the Object Properties window
place the cursor in the IP Address row and enter the IP-address.
en05000643.vsd
Figure 54:
Possibility 1: IP-address via first Wizard window
en05000811.vsd
Figure 55:
Possibility 2: IP-address via IED Object Properties window
The used alternative depends very much on the time at which the IP-address is available.
Alternative 2 allows a change of the IP-address at any time.
90

REC 670 ANSI
Section 9
Establishing connection and verifying the SPA/IEC- communication
Section 9
Establishing connection and

verifying the SPA/IECcommunication
About this chapter
This chapter contains instructions on how to establish connection and verify that the SPA/
IEC-communication operates as intended, when the IED is connected to a monitoring or
control system via the rear SPA/IEC port.
9.1
Entering settings
If the IED is connected to a monitoring or control system via the rear SPA/IEC port, the
SPA/IEC port has to be set either for SPA or IEC use.
9.1.1
Entering SPA settings

The SPA/IEC port is located at IED X310 on the rear side of the IED. Two types of
interfaces can be used:
for plastic fibres with connector type HFBR

for glass fibres with connectors type ST
When using the SPA protocol, the rear SPA/IEC port must be set for SPA use.
Procedure
1.
2.
REC 670 ANSI
Set the operation of the rear optical SPA/IEC port to SPA.

The operation of the rear SPA port can be found on the local HMI or in the PCM
at:
Settings/General settings/Communication/SLM configuration/Rear optical
SPA/IEC port/Protocol selection SPA or IEC 103
When the setting is entered the IED will automatically restart. After the restart the
SPA/IEC port operates as a SPA port.
Set the slave number and baud rate for the rear SPA port

91
Section 9
The slave number and baud rate can be found on the local HMI at:
SPA/IEC port/SPA
Set the same slave number and baud rate as set in the SMS system for the IED.
9.1.2
Entering IEC settings

When using the IEC protocol, the rear SPA/IEC port must be set for IEC use.
The SPA/IEC port is located at IED X310 on the rear side of the IED.
Two types of interfaces can be used:
for plastic fibres with connector type HFBR

for glass fibres with connectors type ST
Procedure
1.
2.
9.2
Set the operation of the rear SPA/IEC port to IEC.

The operation of the rear SPA/IEC port can be found on the local HMI at:
SPA/IEC port/Protocol selection SPA or IEC 103
When the setting is entered the IED will automatically restart. After the restart the
selected IEC port operates as an IEC port.
Set the slave number and baud rate for the rear IEC port
The slave number and baud rate can be found on the local HMI at:
SPA/IEC port/IEC608705103
Set the same slave number and baud rate as set in the IEC master system for the
IED.
Verifying the communication

To verify that the rear communication with the SMS/SCS system is working, there are
some different methods. Choose one of the following.
9.2.1
Verifying SPA communication

Procedure
92

REC 670 ANSI
Section 9
1.
2.
Use a SPA-emulator and send RF to the IED. The answer from the IED should
be IED 670 .
Generate one binary event by activating a function which is configured to an event
block where the used input is set to generate events on SPA. The configuration must
be made with the PCM 600 software. Verify that the event is presented in the SMS/
SCS system.
During the following tests of the different functions in the IED, verify that the events and
indications in the SMS/SCS system are as expected.
9.2.2
Verifying IEC communication

To verify that the IEC communication with the IEC master system is working, there are
some different methods. Choose one of the following.
Procedure
1.
2.
3.
Check that the master system time-out for response from the IED, for example after
a setting change, is > 40 seconds.
Use a protocol analyzer and record the communication between the IED and the
IEC master. Check in the protocol analyzers log that the IED answers the master
messages.
Generate one binary event by activating a function which is configured to an event
block where the used input is set to generate events on IEC. The configuration must
be made with the PCM 600 software. Verify that the event is presented in the IEC
master system.
During the following tests of the different functions in the IED, verify that the events and
indications in the IEC master system are as expected.
9.3
Fibre optic loop

The SPA communication is mainly used for SMS. It can include different numerical
relays/terminals with remote communication possibilities. The fibre optic loop can
contain < 20-30 terminals depending on requirements on response time. Connection to a
personal computer (PC) can be made directly (if the PC is located in the substation) or
by telephone modem through a telephone network with ITU (CCITT) characteristics.
Table 10:
REC 670 ANSI
Max distances between terminals/nodes
glass
< 1000 m according to optical budget
plastic
< 25 m (inside cubicle) according to optical budget

93
Section 9
Remote monitoring
system with
PCM600
Local monitoring
system with
PCM600
IED670
Teleph
one
modem
IED670
IED670
Teleph
one
modem
Optical to electrical
converter, e.g. SPA-ZC 22
or Fiberdata modem
Remote monitoring
system with
PCM600
en05000672.vsd
Local monitoring
system with
PCM600
IED670
Telephone
modem
IED670
IED670
Telephone
modem
Optical to
electrical
converter, e.g. SPA-ZC 22
or Fiberdata
modem
Figure 56:
en05000672_ansi.vsd
Example of SPA communication structure for a station monitoring system
Where:
1
94
A separate minute pulse synchronization from station clock to obtain 1 ms accuracy for time
tagging within the substation might be required.

REC 670 ANSI
Section 9
9.4
Optical budget calculation for serial

communication with SPA/IEC
Table 11:
Example
Distance 1 km
Glass
REC 670 ANSI
Distance 25 m
Plastic
Maximum attenuation for IED 670
- 11 dB
- 7 dB
4 dB/km multi mode: 820 nm - 62.5/125 um
4 dB
0.16 dB/m plastic: 620 nm - 1mm
4 dB
Margins for installation, aging etc.
5 dB
1 dB
Losses in connection box, two contacts (0.5 dB/contact)
1 dB
Losses in connection box, two contacts (1 dB/contact)
2 dB
Margin for 2 repair splices (0.5 dB/splice)
1 dB
Maximum total attenuation
11 dB
7 dB

95
96
Section 10
Establishing connection and verifying the LON communication
Section 10 Establishing connection and

verifying the LON communication
About this chapter
This chapter explains how to set up LON communication and how to verify that LON
communication is up and running.
10.1
Communication via the rear ports
10.1.1
LON communication
LON communication is normally used in substation automation systems. Optical fiber is
used within the substation as the physical communication link.
The test can only be carried out when the whole communication system is installed. Thus,
the test is a system test and is not dealt with here.
The communication protocol LON (Local Optical Network) is available for IED 670
products as an option.
REC 670 ANSI

97
Section 10
Control Center
Station HSI
MicroSCADA
Gateway
Star coupler
RER 111
IED670
IED670
IED670
en05000663.vsd
Figure 57:
Example of LON communication structure for a substation automation

system.
An optical network can be used within the Substation Automation system. This enables
communication with the IED 670s through the LON bus from the operators workplace,
from the control center and also from other IEDs via bay-to-bay horizontal
communication.
The fiber optic LON bus is implemented using either glass core or plastic core fiber optic
cables.
Table 12:
Specification of the fiber optic connectors

Glass fiber
98
Plastic fiber
Cable connector
ST-connector
snap-in connector
Cable diameter
62.5/125 m
1 mm
Max. cable length
1000 m
10 m
Wavelength
820-900 nm
660 nm
Transmitted power
-13 dBm (HFBR-1414)
-13 dBm (HFBR-1521)
Receiver sensitivity
-24 dBm (HFBR-2412)
-20 dBm (HFBR-2521)

REC 670 ANSI
Section 10
10.2.1
The LON Protocol

The LON protocol is specified in the LonTalkProtocol Specification Version 3 from
Echelon Corporation. This protocol is designed for communication in control networks
and is a peer-to-peer protocol where all the devices connected to the network can
communicate with each other directly. For more information of the bay-to-bay
communication, refer to the section Multiple command function
10.2.2
Hardware and software modules

The hardware needed for applying LON communication depends on the application, but
one very central unit needed is the LON Star Coupler and optical fibres connecting the
star coupler to the IEDs. To interface the IEDs from MicroSCADA, the application library
LIB 670 is required.
The HV Control 670 software module is included in the LIB 520 high-voltage process
package, which is a part of the Application Software Library within MicroSCADA
applications.
The HV Control 670 software module is used for control functions in IED 670s. This
module contains the process picture, dialogues and a tool to generate the process database
for the control application in MicroSCADA.
Use the LNT, LON Network Tool to set the LON communication. This is a software tool
applied as one node on the LON bus. In order to communicate via LON, the IEDs need
to know which node addresses the other connected IEDs have, and which network
variable selectors should be used. This is organized by the LNT.
The node address is transferred to the LNT via the local HMI by setting the parameter
ServicePinMsg=YES. The node address is sent to the LNT via the LON bus, or the LNT
can scan the network for new nodes.
The communication speed of the LON bus is set to the default of 1.25 Mbit/s.This can
be changed by the LNT.
The setting parameters for the LON communication are set via the local HMI. Refer to
the Technical reference manual for setting parameters specifications.
The path to LON settings in the local HMI is:
Settings/General settings/Communication/SLM configuration/Rear optical LON
port
If the LON communication from the terminal stops, caused by setting of illegal
communication parameters (outside the setting range) or by another disturbance, it is
possible to reset the LON port of the terminal.
REC 670 ANSI

99
Section 10
By setting the parameter LONDefault=YES, the LON communication is reset in the

terminal, and the addressing procedure can start from the beginning again.
Path in local HMI:Settings\General settings\Communication\SLM configuration\Rear
optical LON port
These parameters can only be set with the LNT, LON Network Tool.
Table 13:
Setting parameters for the LON communication
Parameter
Range
Default
Unit
Parameter description
DomainID
Domain identification number
SubnetID*
0 - 255
Step: 1
Subnet identification number
NodeID*
0 - 127
Step: 1
Node identification number
*Can be viewed in the Local HMI
Path in local HMI: Settings\General settings\Communication\SLM configuration\Rear

optical LON port
These parameters can only be set with the LNT, LON Network Tool.
Table 14:
LON node information parameters
Parameter
Range
Default
Unit
NeuronID*
0 - 12
Not loaded
Neuron hardware identification number in

hexadecimal code
Location
0-6
No value
Location of the node
*Can be viewed in the Local HMI

optical LON port
100

REC 670 ANSI
Section 10
Table 15:
Setting parameters for the session timers
Parameter
Range
Default
Unit
SessionTmo
1-60
20
Session timeout. Only to be changed after

recommendation from ABB.
RetryTmo
100-10000
2000
ms
Retransmission timeout.Only to be
changed after recommendation from ABB.
IdleAckCycle
1-30
Keep active ack.Only to be changed after

recommendation from ABB.
BusyAckTmo
100-5000
300
ms
Wait before sending ack.Only to be

changed after recommendation from ABB.
ErrNackCycle
100-10000
500
ms
Cyclic sending of nack. Only to be changed

after recommendation from ABB.

optical LON port
Table 16:
LON commands
Command
Command description
ServicePinMsg
10.2
Command with confirmation. Transfers the node adress to the LON network tool.
Optical budget calculation for serial

communication with LON
Table 17:
Example
Distance 1 km
Glass
REC 670 ANSI
Distance10 m
Plastic
Maximum attenuation for IED 670
-11 dB
- 7 dB
4 dB/km multi mode: 820 nm - 62.5/125 um
4 dB
0.3 dB/m plastic: 620 nm - 1mm
3 dB
Margins for installation, aging etc.
5 dB
2 dB
Losses in connection box, two contacts (0.75 dB/contact)
1.5 dB
Losses in connection box, two contacts (1dB/contact)
2 dB
Margin for repair splices (0.5 dB/splice)
0.5 dB
Maximum total attenuation
11 dB
7 dB

101
102
Section 11
Configuring the IED and changing settings
Section 11 Configuring the IED and changing

settings
About this chapter
This chapter describes how to change IED settings, either through a PC or the local HMI,
and download a configuration to the IED in order to make commissioning possible.
The chapter does not contain instructions on how to create a configuration or calculate
settings. Please consult the application manual for further information about how to
calculate settings.
It takes a minimum of three minutes for the IED to save the new settings,
during this time the DC supply must not be turned off.
11.1
Overview
The customer specific values for each setting parameter and a configuration file have to
be available before the IED can be set and configured, if the IED is not delivered with a
configuration.
Use the PCM 600 configuration tool to verify that the IED has the expected configuration.
A new configuration is done with the CAP tool. The binary outputs can be selected from
a signal list where the signals are grouped under their function names. It is also possible
to specify a user-defined name for each input and output signal.
Each function included in the IED has several setting parameters which have to be set in
order to make the IED behave as intended. A factory default value is provided for each
parameter. A setting file can be prepared using the parameter setting tool (PST), which
is available in the PCM 600 package.
All settings can be:
REC 670 ANSI

103
Section 11
11.2
Entered manually through the local HMI.

Downloaded from a PC, either locally or remotely using SMS/SCS. Front or rear
port communication has to be established before the settings can be downloaded.
Entering settings through the local HMI

Each of the included functions in the IED has to be set and this can be performed through
the local HMI. The user must browse to the desired function and enter the appropriate
value. The parameters for each function can be found in the local HMI.
The Operators Manual (OM) is structured in a similar way to the LHMI and provides a
detailed guide to the use of the local HMI including paths in the menu structure and brief
explanations of most settings and measurements. See the Technical reference manual for
a complete list of setting parameters for each function. Some of the included functions
may not be used. In this case the user can set the parameter Operation to Off to disable
the function.
11.3
Analog input data

In order to get correct measurement results as well as correct protection functionality, the
analog input channels must be configured. Because all protection algorithms in the IED
utilize the primary system quantities it is extremely important to make sure that connected
current transformer settings are done properly. These data are calculated by the system
engineer and normally set by the commissioning personnel from the local HMI or from
the SMS.
11.3.1
Configuration for analog CT inputs

The analog inputs on the Transformer Module (TRM) are dimensioned for either 1A or
5A. Each TRM has a unique combination of current and voltage inputs. Make sure the
input current rating is correct and that it matches the order documentation.
The primary CT data are entered from the HMI menu branch:
Settings/General Settings/Analog modules/AnalogInputs
The following parameter shall be set for every current transformer connected to the IED:
Table 18:
CT configuration
Rated CT primary current in A
104
Parameter name
CT Prim Input

Range
from -10000 to +10000
Default
0
REC 670 ANSI
Section 11
This parameter defines the primary rated current of the CT. For two set of CTs with ratio
1000/1 and 1000/5 this parameter is set to the same value of 1000 for both CT inputs.
Negative values (i.e. -1000) can be used in order to reverse the direction of the CT current
by software for the differential function. This might be necessary if two sets of CTs have
different neutral (WYE) point locations in relation to the protected busbar. It is
recommended that this parameter is set to zero, for all unused CT inputs.
For main CTs with 2A rated secondary current, it is recommended to connect the
secondary wiring to the 1A input and to set the rated primary current to one half times its
true value. For example, a CT with a primary secondary current ratio of 1000/2A can be
treated as a 500/1A CT.
Take the rated permissive overload values for the current inputs into
consideration.
11.4
Downloading settings and configuration from a

PC
11.4.1
Downloading the configuration and setting files

When downloading a configuration to the IED 670 with the CAP 531 configuration tool,
the IED is automatically set in configuration mode. When the IED is set in configuration
mode, all functions are blocked. The red LED on the IED flashes, and the green LED is
lit while the IED is in the configuration mode.
When the configuration is downloaded and completed, the IED is automatically set into
normal mode. For further instructions please refer to the users manuals for PCM 600.
REC 670 ANSI

105
106
Section 12
Verifying settings by secondary injection
Section 12 Verifying settings by secondary

injection
About this chapter
This chapter describes how to verify that protection functions operate correctly and
according to their settings. It is preferable that only the tested function is in operation.
12.1
Overview
IED test requirements:
Calculated settings
Application configuration diagram
Signal matrix (SMT) configuration
Terminal diagram
Technical reference manual
Three-phase test equipment
PCM 600
The setting and configuration of the IED must be completed before the testing can start.
The terminal diagram, available in the Technical reference manual, is a general diagram
of the IED. but note that the same diagram is not always applicable to each specific
delivery (especially for the configuration of all the binary inputs and outputs). Therefore,
before testing, check that the available terminal diagram corresponds to the IED.
The Technical reference manual contains application and functionality summaries,
function blocks, logic diagrams, input and output signals, setting parameters and technical
data sorted per function.
The test equipment should be able to provide a three-phase supply of voltages and
currents. The magnitude of voltage and current as well as the phase angle between voltage
and current must be variable. The voltages and currents from the test equipment must be
obtained from the same source and they must have minimal harmonic content. If the test
equipment cannot indicate the phase angle, a separate phase-angle measuring instrument
is necessary.
REC 670 ANSI

107
Section 12
Prepare the IED for test before testing a particular function. Consider the logic diagram
of the tested protection function when performing the test. All included functions in the
IED are tested according to the corresponding test instructions in this chapter. The
functions can be tested in any order according to user preferences and the test instructions
are therefore presented in alphabetical order. Only the functions that are used (Operation
is set to On) should be tested.
The response from a test can be viewed in different ways:
Binary outputs signals

Service values in the local HMI (logical signals or phasors)
A PC with PCM 600 application configuration software in debug mode
All setting groups that are used should be tested.

This IED is designed for a maximum continuous current of four times the
rated current.
Please observe the measuring accuracy of the IED, the test equipment and
the angular accuracy for both of them.
Please consider the configured logic from the function block to the output
contacts when measuring the operate time.
12.2
Preparing for test
12.2.1
Overview
This section describes how to prepare the IED to verify settings.
If a test switch is included, start preparation by making the necessary connections to the
test switch. This means connecting the test equipment according to a specific and
designated IED terminal diagram. The IED can then be put into test mode in order to
facilitate the test of individual functions and prevent unwanted operation caused by other
functions. The test switch should then be connected to the IED. The user can also verify
the connection and that the analog input signals are measured and recorded correctly by
injecting currents and voltages required by the specific IED. To make testing even more
effective the Protection and Control IED Manager (PCM 600) should be used. The
108

REC 670 ANSI
Section 12
primary tool at your disposal in the PCM 600 apart from the Parameter Setting Tool (PST)
is the Disturbance Handling Tool (DHT). The content of reports generated by the DHT
can be determined by the user which makes it more efficient. For example, the tool may
be configured to only show time tagged events and to exclude analog information and so
on. The disturbance report settings could be checked to ensure that indications are correct.
Functions to test, signals and parameter names can be found in the technical reference
manual.
12.2.2
Preparing the connection to the test equipment

The IED can be equipped with a test switch of type RTXP 24 or FT. The test switch and
its associated test plug handles are a part of the COMBITEST or FT system of ABB which
provide secure and convenient testing of the IED.
COMBIFLEX system is used, when the test-plug handle is inserted into the test switch.
Preparations for testing are automatically carried out in the proper sequence (i.e. blocking
of tripping circuits, short circuiting of CTs, opening of voltage circuits, making IED
terminals available for secondary injection). Terminals 1 and 12 of the test switch are not
disconnected as they supply DC power to the protection IED. When FT switch is used
for testing, care shall be exercised to open the tripping circuit, ahead of manipulating the
CT fingers.
The test-plug handle leads may be connected to any type of test equipment or instrument.
When a number of protection IEDs of the same type are tested, the test-plug handle only
needs to be moved from the test switch of one protection IED to the test switch of the
other, without altering previous connections.
Using COMBIFLEX test system to prevent unwanted tripping when the handle is
withdrawn, latches on the handle secure it in the half withdrawn position. In this position,
all voltages and currents are restored and any reenergizing transients are given a chance
to decay before the trip circuits are restored. When the latches are released, the handle
can be completely withdrawn from the test switch, restoring the trip circuits to the
protection IED.
If a test switch is not used it is necessary to take measures according to provided circuit
diagrams.
Never disconnect the secondary connection of a current transformer
circuit without short-circuiting the transformer's secondary winding.
Operating a current transformer with the secondary winding open will
cause a massive potential build up that may damage the transformer and
injure humans.
REC 670 ANSI

109
Section 12
12.2.3
Putting the IED into test mode

The IED can be put into test mode before testing. This blocks all functions in the function
test modes folder and allows the user to unblock or release the functions needed for the
test in question. In this way, it is possible to test slower back-up measuring functions
without the interference of faster measuring functions. Test mode is indicated when the
yellow LED flashes.
Procedure
1.
2.
3.
4.
12.2.4
Browse to the TestMode menu and press E.

The Test Mode menu is found under the Test folder in the LHMI:
Test/IED test mode/TestMode
Use the up and down arrows to choose On and press E.
Press the left arrow to exit the menu.
The dialog box Save changes appears.
Choose Yes, press E and exit the menu.
The yellow pickup LED above the LCD will start flashing when the IED is in test
mode.
Connecting test equipment to the IED

Before testing, connect the test equipment according to the IED specific connection
diagram. Pay special attention to the correct connection of the input and output current
terminals, and to the connection of the residual current conductor. Check that the input
and output logical signals in the logic diagram for the function under test are connected
to the corresponding binary inputs and outputs of the IED under test.
110

REC 670 ANSI
Section 12
IA
IB
IB
IC
IC
IN
IN (I4,I5)
VA
VA
VB
VB
VC
VC
VN
VN
REx 670
IED TEST SET
IA
VN (U4,U5)
TRIP A
TRIP B
TRIP C
IEC61850
en05000467_ansi.vsd
Figure 58:
12.2.5
Connection example of the test set to the IED 670
Verifying the connections and the analog inputs

The user must verify that the connections are correct and that the analog signals are
measured correctly.
Apply input signals as needed according to the actual hardware and the
logic configuration made in PCM 600.
Procedure
1.
2.
3.
4.
REC 670 ANSI
Inject a symmetrical three-phase current and voltage at rated value.

Inject a phase-to-phase voltage and through going phase-to-phase current at rated
value.
Compare the injected value with the measured value.
The voltage phasor and current phasor menus are located under the Measurements
folder in the LHMI:
Measurements/Analog primary values
and
Measurements/Analog secondary values
Take into consideration ratio factor settings for CTs and VTs.
Compare the frequency reading with the set frequency and the direction of the power
with the injected power.
The frequency and active power are located in the local HMI under:

111
Section 12
5.
6.
12.2.6
Measurements/Monitoring/ServiceValues/SVR
Inject an unsymmetrical three-phase current and voltage at rated value in two
phases.
Compare the injected value with the measured value.
The current phasor menu is located in the local-HMI under:
Measurements/Monitoring/CurrentPhasors/CP
The voltage phasor menu is located in the local HMI under:
Measurements/Monitoring/VoltagePhasors/VP
Releasing the function(s) to be tested

The user can release/unblock the function(s) to be tested. This is done to ensure that only
the function(s) under test are in operation and that other functions are prevented from
operating. The user can release the tested function(s) by setting the corresponding blocked
parameter under Function test modes to NO in the local HMI. When testing a function in
this blocking feature, remember that not only the actual function must be activated, but
the whole sequence of interconnected functions (from measuring inputs to binary output
contacts), including logic and so on. Before starting a new test mode session the user
should scroll through every function to ensure that only the function to be tested (and the
interconnected ones) are set to NO. A function is also blocked if the BLOCK input signal
on the corresponding function block is active, which depends on the configuration. The
user should therefore ensure that the logical status of the BLOCK input signal is equal to
0 for the function to be tested. The user could also individually block event blocks to
ensure that no events are reported to a remote station during the test.
The function is blocked if the corresponding setting under the Function
test modes menu remains on and the TEST-INPUT signal remains active.
All functions that were blocked or released from a previous test mode
session are reset when a new test mode session is started.
Procedure
1.
2.
3.
112
Browse to the Function test modes menu.

The Function test modes menu is located in the local HMI under:
Test/Function test modes
Browse to the function instance that should be released.
Use the left and right arrow buttons. Press E when the desired function has been
found.
Select Yes. Press 'E' and the new setting is valid.

REC 670 ANSI
Section 12
12.2.7
Disturbance report
12.2.7.1
Introduction
The following functions are included in the disturbance report function:
Disturbance recorder
Event list
Event recorder
Fault locator (not included in all products)
Trip value recorder
Indications
If the disturbance report is running, then its sub-function are also running and so it is not
possible to only switch these functions off. The disturbance report function is switched
off from PCM 600 or from the local HMI.
12.2.7.2
Disturbance report settings

When the IED is in test mode, the disturbance report can be made active or inactive. If
the disturbance recorder is turned on during test mode, recordings will be made. When
test mode is switched off all recordings made during the test session are cleared.
Settings for the control of the disturbance recorder during test mode are located in the
local HMI under:
Settings/General settings/Monitoring/Disturbance report/
DisturbanceReport(RDRE)
12.2.7.3
Disturbance recorder (DR)

Evaluation of the results from the disturbance recording function requires access to a PC
either permanently connected to the IED or temporarily connected to the Ethernet port
(RJ 45) on the front. The PCM 600 software package must be installed in the PC.
Disturbance upload can be performed by the use of PCM 600 or by any third party tool
with IEC 61850 protocol. Reports can automatically be generated from the PCM 600
tool. Disturbance files can be analyzed by any tool reading Comtrade formatted
disturbance files.
It could be useful to have a printer for hard copies. The behavior of the disturbance
recording function can be checked when IED protective functions are tested. When the
IED is set to operate in test mode, there is a separate setting for operation of the disturbance
report, which also affects the disturbance recorder.
REC 670 ANSI

113
Section 12
A manual trig can be started at any time. This results in a recording of the actual values
from all recorded channels.
12.2.7.4
Event recorder (ER)

Prepare the IED for verification of settings as outlined in section "Overview" and
section "Preparing for test" in this chapter.
The result from the event recorder can be viewed on the local HMI or, after upload, in
PCM 600.
When testing binary inputs, the event list (EL) might be used instead. No uploading or
analyzing of registrations is then needed since the event list keeps running, independent
of start of disturbance registration.
12.2.8
Identifying the function to test in the technical reference manual

The user can use the technical reference manual (TRM) to identify function blocks, logic
diagrams, input and output signals, setting parameters and technical data.
12.2.9
Exit test mode

The following procedure is used to return to normal operation.
Procedure
1.
2.
3.
Navigate to the test mode folder.

Change the 'On' setting to 'Off'. Press the 'E' key and the left arrow key.
Answer 'YES', press the 'E' key and exit the menus.
12.3
Basic IED functions
12.3.1
Parameter setting groups (ACGR)

Prepare the IED for verification of settings as outlined in section "Overview" and section
"Preparing for test" in this chapter.
114

REC 670 ANSI
Section 12
12.3.1.1
Verifying the settings

Procedure
1.
2.
3.
4.
12.3.1.2
Check the configuration of binary inputs that control the selection of the active
setting group.
Browse the ActiveGroup menu to achieve information about the active setting
group.
The ActiveGroup menu is located in the local HMI under:
Test/Function status/Setting groups
Connect the appropriate dc voltage to the corresponding binary input of the IED
and observe the information presented on the HMI display.
The displayed information must always correspond to the activated input.
Check that the corresponding output indicates the active group.
Operating procedures for the PC aided methods of changing the active setting groups
are described in the corresponding PCM documents and instructions for the
operators within the SCS are included in the SCS documentation.
Completing the test

Continue to test another function or end the test by changing the test mode setting to off.
Restore connections and settings to their original values, if they were changed for testing
purposes.
12.4
Differential protection
12.4.1
High impedance differential protection (PDIF, 87)

12.4.1.1

Procedure
1.
REC 670 ANSI
Connect single phase or three phase test set to inject the operating voltage. The
injection shall be on the primary side of the stabilizing resistor.
Note! As the operating voltage is adjusted on the stabilizing resistor and with the
setting of the resistor value in the function this is essential for the measurement of

115
Section 12
the expected value. Normally a slightly higher operating value is no problem as the
sensitivity is not influenced much.
2. Connect the trip contact to the test set to stop the test set for measurement of trip
times below.
3. Increase the voltage and make note of the operate value TripPickup. This is done
with manual test and without trip of the test set.
4. Reduce the voltage slowly and make note of the reset value. The reset value must
be high for this function.
5. Check the operating time by injecting a voltage corresponding to 1,2 TripPickup>
level Make note of the measured trip time.
6. If required, verify the trip time at another voltage. Normally 2*TripPickup is
selected.
7. If used measure the alarm level operating value. Increase the voltage and make note
of the operate value AlarmPickup. This is done with manual test and without trip
of the test set.
8. Measure the operating time on the alarm output by connecting the stop of the test
set to an output from tAlarm. Inject a voltage 1,2*AlarmPickup and measure the
alarm time.
9. Check that trip and alarm outputs operates according to the configuration logic.
10. Finally check that pickup and alarm information is stored in the Event menu and if
a serial connection to the SA is available verify that the correct and only the required
signals are presented on the local station HMI and on the SCADA system.
Information on how to use the event menu is found in the IED 670 operator's manual.
12.4.1.2
Completing the test

purposes.
12.5
Current protection
12.5.1
Instantaneous phase overcurrent protection (PIOC, 50)

To verify the settings the following fault type should be tested:
116

REC 670 ANSI
Section 12
One for a phase-to-ground fault
Ensure that the maximum continuous current of the IED does not exceed four times its
rated value.
12.5.1.1
Measuring the operate limit of set values

Procedure
1.
2.
3.
4.
5.
6.
12.5.1.2
Inject a phase current into the IED with an initial value below that of the setting.
Set operation mode to 1 out of 3.
Increase the injected current in the Ln phase until the TR_A (TR_B or TR_C) signal
appears.
Switch the fault current off.
Observe the maximum permitted overloading of the current circuits in the IED
Compare the measured operating current with the set value.
Set operation mode to 2 out of 3 and inject current into one of the phases. Checkno operation.
Completing the test

purposes.
12.5.2
Four step phase overcurrent protection (PTOC, 51/67)

Prepare the IED for verification of settings outlined in section "Overview" and section
Directional phase overcurrent current function
12.5.2.1

Procedure
1.
REC 670 ANSI
Connect the test set for appropriate current injection to the appropriate IED
terminals.
If there is any configuration logic which is used to enable/block any of 4 available
overcurrent steps, make sure that step under test is enabled (i.e. end fault protection).
If 1 of 3 currents for operation is chosen: Connect the injection current to terminals
A and neutral.

117
Section 12
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
118
If 2 of 3 currents for operation is chosen: Connect the injection current into terminal
A and out from terminal B.
If 3 of 3 currents for operation is chosen: Connect the symmetrical 3 phase injection
current into terminals A, B and C.
Connect the test set for the appropriate three-phase voltage injection to the IED
terminals A, B and C. The protection shall be fed with a symmetrical three phase
voltage.
Set the injected polarizing voltage slightly larger than the set minimum polarizing
voltage (default is 5% of Vn) and set the injection current to lag the appropriate
voltage by an angle of about 80 if forward directional function is selected.
If 1 of 3 currents for operation is chosen: The voltage angle of phase A is the
reference.
If 2 of 3 currents for operation is chosen: The voltage angle of phase A the voltage
angle of B is the reference.
If 3 of 3 currents for operation is chosen: The voltage angle of phase A is the
reference.
If reverse directional function is selected, set the injection current to lag the
polarizing voltage by an angle equal to 80 + 180.
Increase the injected current and note the operated value of the studied step of the
function.
Decrease the current slowly and note the reset value.
If the test has been performed by injection of current in phase A, repeat the test when
injecting current into terminals B and C with polarizing voltage connected to
terminals B respectively C (1 of 3 currents for operation).
If the test has been performed by injection of current in phases A B, repeat the
test when injecting current into terminals B C and C A with appropriate phase
angle of injected currents.
Block higher set stages when testing lower set stages according to below.
Connect a trip output contact to a timer.
Set the injected current to 200% of the operate level of the tested stage, switch on
the current and check the time delay.
For inverse time curves, check the operate time at a current equal to 110% of the
operate current for tmin.
Check that all trip and pickup contacts operate according to the configuration (signal
matrixes)
Reverse the direction of the injected current and check that the protection does not
operate.
If 2 of 3 or 3 of 3 currents for operation is chosen: Check that the function will not
operate with current in one phase only.
Repeat the above-described tests for the higher set stages.
Finally check that pickup and trip information is stored in the event menu.

REC 670 ANSI
Section 12
Check of the non-directional phase over-current function. This is

done in principle as instructed above, without applying any
polarizing voltage.
12.5.2.2
Completing the test

purposes.
12.5.3
Instantaneous residual overcurrent protection (PIOC, 50N)

To verify the settings the following fault type should be tested:
One for a phase-to-ground fault
Ensure that the maximum continuous current of the terminal does not exceed four times
its rated value.
12.5.3.1

Procedure
1.
2.
3.
4.
12.5.3.2
Inject a phase current into the IED with an initial value below that of the setting.
Increase the injected current in the Ln or in the neutral (summated current input)
phase until the TRIP signal appears.
Observe the maximum permitted overloading of the current circuits in the IED
Compare the measured operating current with the set value.
Completing the test

purposes.
REC 670 ANSI

119
Section 12
12.5.4
Four step residual overcurrent protection (PTOC, 51N/67N)

12.5.4.1
Four step directional overcurrent protection

Procedure
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
12.5.4.2
Connect the test set for single current injection to the appropriate IED terminals.
Connect the injection current to terminals A and neutral, or to terminals N and
neutral.
Set the injected polarizing voltage slightly larger than the set minimum polarizing
voltage (default 5 % of Vn) and set the injection current to lag the voltage by an
angle equal to the set reference characteristic angle (AngleRCA) if the forward
directional function is selected.
If reverse directional function is selected, set the injection current to lag the
polarizing voltage by an angle equal to RCA+ 180.
Increase the injected current and note the value at which the studied step of the
function operates.
If the test has been performed by injection of current in phase A, repeat the test when
injecting current into terminals B and C with a polarizing voltage connected to
terminals B respectively C.
Block higher set stages when testing lower set stages according to the instructions
that follow.
Connect a trip output contact to a timer.
Set the injected current to 200 % of the operate level of the tested stage, switch on
the current and check the time delay.
For inverse time curves, check the operate time at a current equal to 110 % of the
operate current for tmin.
Check that all trip and start contacts operate according to the configuration (signal
matrixes)
Reverse the direction of the injected current and check that the protection does not
operate.
Check that the protection does not operate when the polarizing voltage is zero.
Repeat the above-described tests for the higher set stages.
Finally, check that pickup and trip information is stored in the event menu.
Four step non-directional overcurrent protection

Procedure
120

REC 670 ANSI
Section 12
1.
12.5.4.3
In principle this is done as described above, see section "Four step directional
overcurrent protection", but without applying any polarizing voltage.
Completing the test

purposes.
12.5.5
Sensitive directional residual overcurrent and power protection

(PSDE, 67N)
Prepare the terminal for verification of settings as outlined in section "Overview" and
section "Preparing for test" in this chapter
Figure 59 shows the principal connection of the test-set during the test of the sensitive
directional residual overcurrent protection. Observe that the polarizing voltage is equal
to -3V0.
IED
Relay test set

NI
IN
V_A
V_B
V_C
V1
V2
V3
V_N
V_N
-3V0
TRIP
en07000094_ansi.vsd
Figure 59:
Principle connection of the test-set
Values of the logical signals belonging to the sensitive directional residual overcurrent
protection are available under menu tree:
Test/Function status/Current protection/SensDirResOvCurr/SDE
REC 670 ANSI

121
Section 12
12.5.5.1
Measuring the operate and time limit for set values

Operation mode 3I0cos
Procedure
1.
2.
3.
4.
5.
6.
7.
8.
122
Set the polarizing voltage to 1.2xVNRel> and the phase angle between voltage and
current to the set characteristic angle (RCADir), the current lagging the voltage.
Take setting RCAComp into consideration if not equal to 0.
Measure that the operate current of the set directional element is equal to the
INcosPhi> setting.
The I Dir (I0 cos(Angle)) function activates the BFI_3P and STDIRIN output.
Measure with angles j = RCADir +/- 45 that the measuring element operates when
I0 cos (RCADir - j) =INcosPhi>.
Compare the result with the set value.
Take the set characteristic into consideration, see figure 60 and figure 61.
Measure the operate time of the timer by injecting a current two times the set
INcosPhi> value and the polarizing voltage 1.2xVNRel>.
Compare the results with the set value tDef.
Set the polarizing voltage to xero and increase until VNREL appears. Compare the
voltage with the set value UVNRel>.
Continue to test another function or complete the test by setting the test mode to
off.

REC 670 ANSI
Section 12
3I0
3I0 cos
Operate area
-3V0=Vref
RCA = 0
ROA
en06000650_ansi.vsd
Figure 60:
REC 670 ANSI
Characteristic with ROADir restriction

123
Section 12
Operate area
-3V0=Vref
Instrument
transformer
angle error
RCA = 0
RCAcomp
Characteristic after
angle compensation
3I0 (prim)
3I0 (to prot)
en06000651_ansi.vsd
Figure 61:
Explanation of RCAcomp.
Operation mode 3I0x3U0xcosj

Procedure
1.
2.
3.
4.
5.
124
Measure that the operate power is equal to the SN> setting for the set directional
element.
Note that for pick-up, both the injected current and voltage must be greater than the
set values INRel> and VNRel> reespectively.
The function activates the BFI_3P and STDIRIN output.
Measure with angles j = RCADir +/- 45 that the measuring element operates when
3I0 3V0 cos (RCADir - j) = SN>.
Compare the result with the set value tDef.
Measure the operate time of the timer by injecting 1.2xVNRel> and a current to get
two times the set SN> operate value.

REC 670 ANSI
Section 12
Tinv = kSN Sref / 3I 0test 3V0test cos(j )
6.
7.
(Equation 1)
Compare the result with the expected value.

The expected value depends on whether definite or inverse time was selected.
off.
Operation mode 3Io and j

Procedure
1.
2.
3.
4.
5.
6.
7.
REC 670 ANSI
Measure that the operate power is equal to the INDir> setting for the set directional
element.
Note that for pickup, both the injected current and voltage must be greater than the
set values INRel> and VNRel> respectively.
Measure with angles j around RCADir +/- ROADir.
Compare the result with the set values, refer to figure 62 for example characteristic.
Measure the operate time of the timer by injecting a current to get two times the set
S operate value.
Compare the result with the set value tDef.
off.

125
Section 12
RCA = 0
ROA = 80
Operate area
3I0
80
-3V0
en06000652_ansi.vsd
Figure 62:
Example characteristic
Non-directional earthground fault current protection

Procedure
1.
2.
3.
4.
Measure that the operate current is equal to the INNonDir> setting.

Measure the operate time of the timer by injecting a current to get two times the set
INNonDir> operate value.
Compare the result with the expected value.
The expected value depends on whether definite time tINNonDir or inverse time
was selected.
off.
Residual overvoltage release and protection

Procedure
1.
2.
3.
126
Measure that the operate voltage is equal to the UN> setting.

The function activates the BFI_3P and STUN signals
Measure the operate time by injecting a voltage 1.2 timers set VN> operate value.
Compare the result with the set tVNNonDir operate value.

REC 670 ANSI
Section 12
4.
5.
6.
12.5.5.2
Inject a voltage 0.8xVNRel>and a current high enough to operate the directional

function at the chosen angle.
Increase the voltage until the directional function is released.
Compare the measured value with the set VNRel> operate value.
Completing the test

purposes.
12.5.6
Thermal overload protection, one time constant (PTTR, 26)

Check that the input logical signal BLOCK is logical zero and that on the local HMI, the
logical signal TRIP, PICKUP and ALARM are equal to logical 0.
12.5.6.1
Measuring the operate and time limit of set values

Testing the protection without external temperature compensation
(NonComp)
Procedure
1.
2.
3.
4.
5.
6.
7.
8.
REC 670 ANSI
Quickly set the measured current (fault current) in one phase to about 300% of
IRef (to minimise the trip time), and switch the current off.
Reset the thermal memory under menu tree:
Reset/Reset temperature/ThermalOverload1TimeConst(PTTR,26)/THL
Switch the fault current on and take note of the temperature:
Test/Current protection/ThermOverLoad1TimeConst(PTTR,26)/THL/
TEMP
Check the Alarm time limit AlarmTemp during injection.
Measure the signal ALARM until it appears on the corresponding binary output or
on the local HMI.
Compare the measured temperature with the setting.
Measure the THL protection trip time.
Use the TRIP signal from the configured binary output to stop the timer.
Take the TEMP readings.
Compare with the setting of TripTemp.
Activate the BLOCK binary input.
The signals ALARM, PICKUP and TRIP should disappear.

127
Section 12
9. Reset the BLOCK binary input.

10. Check the reset limit (TdReset).
Measure the signal PICKUP until it disappears on the corresponding binary output
or on the local HMI, take the TEMP readings and compare with the setting of
ReclTemp.
11. Compare the measured trip time with the setting according to the formula.
12. Reset the thermal memory.
13. Continue to test another function or end the test by changing the test mode setting
to off.
12.5.6.2
Completing the test

purposes.
12.5.7
Thermal overload protection, two time constants (PTTR, 49)

12.5.7.1
Checking operate and reset values

Procedure
1.
2.
3.
4.
5.
6.
7.
8.
9.
128
Connect symmetrical 3-phase currents to the appropriate current terminals of RET

670.
Set the Time constant 1 (Tau1) and Time Constant 2 (Tau2) temporarily to 1 minute.
Set the 3-phase injection currents slightly lower than the set operate value of stage
IBase1, increase the current in phase A until stage IBase1 operates and note the
operate value.
Observe the maximum permitted overloading of the current circuits in the terminal.
Check in the same way as the operate and reset values of IBase1 for phases B and
C.
Activate the digital input for cooling input signal to switch over to base current
IBase2.
Check for all three phases the operate and reset values for Ib2 in the same way as
described above for stage IBase1.
Deactivate the digital input signal for stage IBase2.
Set the time constant for IBase1 in accordance with the setting plan.
Set the injection current for phase A to 1.50 x IBase1.

REC 670 ANSI
Section 12
10. Connect a trip output contact to the timer and monitor the output of contacts
Alarm1 and Alarm2 to digital inputs in test equipment.
Read the heat content in the thermal protection from the local HMI and wait until
the content is zero.
11. Switch on the injection current and check that Alarm1 and Alarm2 contacts operate
at the set percentage level and that the operate time for tripping is in accordance
with the set Time Constant 1 (Tau 1).
With setting Itr = 101% IBase1 and injection current 1.50 x IBase1, the trip time
from zero content in the memory shall be 0.60 x Time Constant 1 (Tau1).
12. Check that all trip and alarm contacts operate according to the configuration logic.
13. Switch off the injection current and check from the service menu readings of thermal
status and LOCKOUT that the lockout resets at the set percentage of heat content.
14. Activate the digital input for cooling input signal to switch over to base current
IBase2.
Wait 5 minutes to empty the thermal memory and set Time Constant 2 (Tau2) in
accordance with the setting plan.
15. Test with injection current 1.50 x IBase2 the thermal alarm level, the operate time
for tripping and the lockout reset in the same way as described for stage IBase1.
16. Finally check that pickup and trip information is stored in the Event menu
Information on how to use the event menu is found in the RET 670 operators manual.
12.5.7.2
Completing the test

purposes.
12.5.8
Breaker failure protection (RBRF, 50BF)

The breaker-failure protection should normally be tested in conjunction with some other
function that provides an initiate signal. An external initiate signal can also be used.
The function(s) has to be set and configured before the testing can start. The BFP function
is highly flexible in that it permits a choice of functional and tripping modes. The various
modes are checked at the factory as part of the design verification. In certain cases only
modes with a high probability of coming into operation need to be checked, in order to
verify the configuration and settings.
Required for testing the function are:
REC 670 ANSI

129
Section 12
Calculated settings
Valid configuration diagram for the IED
Valid terminal diagram for the IED
Technical reference manual
Three-phase test equipment
The Technical reference manual contains application and functionality summaries,

function blocks, logic diagrams, input and output signals, a list of setting parameters and
technical data for the function.
The test equipment should be able to provide a three-phase supply of currents (and for
some pickup functions also voltage). The magnitude and angle of currents (and voltages)
should be possible to vary.
Make sure the IED is prepared for test before starting the test session. Consider the logic
diagram of the function when performing the test. The response from a test can be viewed
in different ways:
Binary output signals

Service values in the local HMI (logical signal or phasors)
A PC with PCM 600 (configuration software) in debug mode
To verify the settings in the most common back-up trip mode 1 out of 3 it is sufficient
to test phase-to-ground faults.
At mode 2 out of 4 the Phase current setting, Pickup_PH can be checked by single
phase injection where the return current is connected to the summated current input. The
value of residual (EF) current IN set lower than Pickup_PH is easiest checked in backup trip mode 1 out of 4.
12.5.8.1
Checking the phase current operate value, Pickup_PH

The check of the Pickup_PH current level is best made in FunctionMode=Current and
BuTripMode= 1 out of 3 or 2 out of 4.
Procedure
1.
2.
3.
4.
130
Apply the fault condition, including initiation of BFP, with a current below set
Pickup_PH.
Repeat the fault condition and increase the current in steps until a trip occurs.
Compare the result with the set Pickup_PH.
Disconnect AC and initiate input signals.
Note: If No IPickup check or Retrip off is set, only back-up trip can be used to
check set Pickup_PH.

REC 670 ANSI
Section 12
12.5.8.2
Checking the residual (GF) current operate value Pickup_N set below
Pickup_PH
The check of low set Pickup_N current level is best made in FunciontMode= Current
and BuTripMode= 1 out of 4.
Procedure
1.
2.
3.
4.
12.5.8.3
Apply the fault condition, including initiation of BFP, with a current just below set
Pickup_N.
Repeat the fault condition and increase the current in steps until trip appears.
Compare the result with the set Pickup_N.
Checking the re-trip and back-up times

The check of the set times can be made in connection with the check of operate values
above. Choose the applicable function and trip mode, such as FunctMode= Current and
RetripMode = Current check.
Procedure
1.
2.
3.
12.5.8.4
Apply the fault condition, including initiation of BFP, well above the set current
value. Measure time from Start of BFP.
Check the re-trip t1 and back-up trip times t2 and t3
In applicable cases the back-up trip for multi-phase start t2MPh and back-up trip
2, t2 + t3 can also be checked. For check of t2MPh a two-phase or three-phase
initiation shall be applied.
Verifying the re-trip mode

Choose the mode below, which corresponds to the actual case. In the cases below it is
assumed that FunctionMode = Current is selected.
Checking the case without re-trip, RetripMode = Off

Procedure
1.
2.
3.
4.
REC 670 ANSI
Set RetripMode = Off.

value.
Verify that no re-trip, but back-up trip is achieved after set time.
Disconnect AC and initiation input signals.

131
Section 12
Checking the re-trip with current check, RetripMode = I>RetripMode =
Current check
Procedure
1.
2.
3.
4.
5.
6.
Set RetripMode = Current check.

Apply the fault condition, including initiation BFP, well above the set current value.
Verify that retrip is achieved after set time t1 and back-up trip after time t2
Apply the fault condition, including initiation of BFP, with current below set current
value.
Verify that no re-trip, and no back-up trip is obtained.
Checking re-trip without current check, RetripMode= No I>RetripMode=

No Current check
Procedure
1.
2.
3.
4.
5.
6.
12.5.8.5
Set RetripMode = No Current check.

value.
Verify that re-trip is achieved after set time t1, and back-up trip after time t2.
Apply the fault condition, including initiation of BFP, with current below set current
value.
Verify that re-trip is achieved after set time t1, but no back-up trip is obtained.
Verifying the back-up trip mode

In the cases below it is assumed that FunctionMode = Current is selected.
Checking that back-up tripping is not achieved at normal CB tripping
Use the actual tripping modes. The case below applies to re-trip with current check.
Procedure
1.
2.
3.
4.
132
Apply the fault condition, including initiation of BFP, with phase current well above
set value IP
Arrange switching the current off, with a margin before back-up trip time, t2. It may
be made at issue of re-trip command.
Check that re-trip is achieved, if selected, but no back-up trip.

REC 670 ANSI
Section 12
The normal mode BuTripMode = 1 out of 3 should have been verified in the tests above.
In applicable cases the modes 1 out of 4 and 2 out of 4 can be checked. Choose the
mode below, which corresponds to the actual case.
Checking the case BuTripMode = 1 out of 4
It is assumed that EF current setting Pickup_N is below phase current setting

Pickup_PH.
Procedure
1.
2.
3.
4.
Set BuTripMode = 1 out of 4.

Apply the fault condition, including initiation of BFP, with one phase current below
set Pickup_PH but above Pickup_N. The residual (EF) should then be above set
Pickup_N.
Verify that back-up trip is achieved after set time. If selected, re-trip should also
appear.
Checking the case BuTripMode = 2 out of 4
The EF current setting Pickup_N may be equal to or below phase current setting
Pickup_PH.
Procedure
1.
2.
3.
4.
5.
6.
12.5.8.6
Set BuTripMode = 2 out of 4

Apply the fault condition, including initiation of BFP, with one phase current above
set Pickup_PH and residual (GF) above set Pickup_N It can be obtained by applying
a single phase current.
Verify that back-up trip is achieved after set time. If selected, re-trip should also
appear.
Apply the fault condition, including initiation of BFP, with at least one phase current
below set Pickup_PH and residual (GF) above set Pickup_N. The current may be
arranged by feeding three (or two) phase currents with equal phase angle (I0component) below Pickup_PH, but of such value that the residual (GF) current (3I0)
will be above set value Pickup_N.
Verify that back-up trip is not achieved.
Verifying instantaneous back-up trip at CB faulty condition

Applies in a case where signal CB faulty and unable to trip is connected to input
52FAIL.
Procedure
REC 670 ANSI

133
Section 12
1.
2.
3.
4.
5.
12.5.8.7
Repeat the check of back-up trip time. Disconnect current and initiation input
signals.
Activate the input 52FAIL. The output CBALARM (CB faulty alarm) should appear
after set time tCBAlarm. Keep the input activated.
Apply the fault condition, including initiation of BFP, with current above set current
value.
Verify that back-up trip is obtained without intentional delay, e.g. within 20 ms from
application of initiation.
Disconnect injected AC and input signals.
Verifying the case FunctionMode = Contact

It is assumed that re-trip without current check is selected, RetripMode = No Current
check.
Procedure
1.
2.
3.
4.
5.
6.
7.
8.
9.
12.5.8.8
Set FunctionMode = Contact

Apply input signal for CB closed to relevant input or inputs 52a_A (B or C)
Apply input signal, or signals for initiation of BFP. The value of current could be
low.
Verify that re-trip and back-up trip are achieved after set times.
Disconnect the start signal(s). Keep the CB closed signal(s).
Apply input signal(s), for initiation of BFP. The value of current could be low.
Arrange disconnection of CB closed signal(s) well before set back-up trip time t2.
Verify that back-up trip is not achieved.
Disconnect injected AC and initiation input signals.
Verifying the function mode Curr&Cont Check

To be made only when FunctionMode = Curr and Cont is selected. It is suggested to
make the tests in one phase only, or at three-pole trip applications for just three-pole
tripping.
Checking the case with fault current above set value IP>Pickup_PH
The operation shall be as in FunctionMode = Current.
Procedure
134

REC 670 ANSI
Section 12
1.
2.
3.
4.
5.
Set FunctionMode = Curr&Cont Check

Leave the inputs for CB close inactivated. These signals should not influence.
Apply the fault condition, including initiation of BFP, with current above the set
Pickup_PH value.
Check that the re-trip, if selected, and back-up trip commands are achieved.
Checking the case with fault current below set value

I>BlkContPickup_BlkCont
The case shall simulate a case where the fault current is very low and operation will
depend on CB position signal from CB auxiliary contact. It is suggested that re-trip
without current check is used; setting Retrip = No I>Retrip = No Current check.
Procedure
1.
2.
3.
4.
5.
6.
7.
8.
9.
12.5.8.9
Set FunctionMode = Curr&Cont Check

Apply input signal for CB closed to relevant input or inputs 52a_A (B or C)
Apply the fault condition with input signal(s) for initiation of BFP. The value of
current should be below the set value Pickup_BlkCont
Verify that re-trip (if selected) and back-up trip are achieved after set times. Failure
to trip is simulated by keeping the signal(s) CB closed activated.
Disconnect the AC and the initiation signal(s). Keep the CB closed signal(s).
Apply the fault and the initiation again. The value of current should be below the
set value Pickup_BlkCont
Arrange disconnection of BC closed signal(s) well before set back-up trip time t2.
It simulates a correct CB tripping.
Verify that back-up trip is not achieved. Re-trip can appear, e.g. due to selection
Re-trip without current check.
Completing the test

purposes.
12.5.9
Stub protection (PTOC, 50STB)

REC 670 ANSI

135
Section 12
12.5.9.1

Procedure
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
12.5.9.2
Check that the input logical signals BLOCK and ENABLE are logical zero and note
on the local HMI that the TRIP logical signal is equal to the logical 0.
Logical signals for STUB protection are available under menu tree:
Measurements/Current protection/Stub/STB
Activate the ENABLE binary input.
STUB protection settings are available under menu tree:
Settings/Setting group N/Current protection/Stub/STB
Quickly set the measured current (fault current) in one phase to about 110% of the
set operating current, and switch the current off with the switch.
Observe the maximum permitted overloading of the current circuits in the IED.
Switch the fault current on and measure the operating time of the STUB protection.
Use the TRIP signal from the configured binary output to stop the timer. The
operation should be instantaneously.
Switch on the fault current (110% of the setting).
No TRIP signal should appear.
Switch off the fault current.
Quickly set the measured current (fault current) in same phase to about 90% of the
set operating current, and switch the current off with the switch.
Switch the fault current on.
Reset the ENABLE binary input.
Switch the fault current on.
Completing the test

purposes.
12.5.10
Polediscrepancy protection (RPLD, 52PD)

Prepare the terminal for verification of settings as outlined in section "Preparing for
test" and section "Preparing for test" in this chapter.
136

REC 670 ANSI
Section 12
12.5.10.1

Procedure
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
REC 670 ANSI
External detection logic, Contact function selection=ContactSel setting equals PD

signal from CB. Activate the EXTPDIND binary input, and measure the operating
time of the PD protection.
Use the TRIP signal from the configured binary output stop the timer.
Compare the measured time with the set value t_TripDelay.
Reset the EXTPDIND binary input.
Activate the BLKDBYAR binary input.
This test should be performed together with AR.
Activate the EXTPDIND binary input.
Reset both BLKDBYAR and EXTPDIND binary inputs.
Activate EXTPDIND binary input.
NO TRIP signal should appear.
Reset both BLOCK and EXTPDIND binary inputs.
If Internal detection logic Contact function selection=ContactSel setting equals Pole
position from auxiliary contacts. Then set inputs 52b_A...52a_C in a status that
activates the pole discordance logic and repeats steps 2-9 above.
Unsymmetry current detection with CB monitoring: Set measured current in one
phase to 110% of Current Release level. Activate CLOSECMD and measure the
operating time of the PD protection.
Use the TRIP signal from the configured binary out put stop the timer.
Deactivate the CLOSECMD.: Set measured current in one phase to 90% of Current
Release level. Activate CLOSECMD.
Repeat point 11 and 12 using OPENCMD instead of CLOSECMD. Unsymmetry
current detection with CB monitoring: Set all three currents to 110% of Current
Release level. Activate CLOSECMD.
NO TRIP signal should appear due to symmetrical condition.
Deactivate the CLOSECMD. Decrease one current with 120% of the Current
Unsymmetry level compared to the other two phases. Activate CLOSECMD and
measure the operating time of the PD protection.
Use the TRIP signal from the configured binary out put stop the timer.
Deactivate the CLOSECMD. Decrease one current with 80% of the Current
Unsymmetry level compared to the other two phases. Activate CLOSECMD.

137
Section 12
12.5.10.2
Completing the test

purposes.
12.5.11
Directional underpower protection (PDUP)

12.5.11.1

The underpower protection shall be set to values according to the real set values to be
used. The test is made by means of injection of voltage and current where the amplitude
of both current and voltage and the phase angle between the voltage and current can be
controlled. During the test the analog outputs of active and reactive power shall be
monitored.
Procedure
1.
Connect the test set for injection of voltage and current corresponding to the measure
mode to be used in the application. If a three phase test set is available this could
be used for all the measure modes. If a single phase current/voltage test set is
available the test set should be connected to a selected input for one phase current
and voltage.
Set value: measureMode
Formula used for complex power calculation
A, B, C
S = V A I A* + VB I B* + VC I C *
Arone
S = V AB I A* - VBC IC *
PosSeq
S = 3 VPosSeq I PosSeq*
AB
S = VAB ( I A* - I B* )
138

REC 670 ANSI
Section 12
BC
S = VBC ( I B* - IC * )
CA
S = VCA ( I C * - I A* )
A
S = 3 VA I A*
B
S = 3 VB I B*
C
S = 3 VC I C *
2.
3.
4.
5.
6.
7.
12.5.11.2
Adjust the injected current and voltage to the set rated values IBase and VBase
(converted to secondary current and voltage). The angle between the injected current
and voltage shall be set equal to the set direction Angle1 (equal to 0 for low forward
power protection). Check that the monitored active power is equal to 100% of rated
power and that the reactive power is equal to 0% of rated power.
Change the angle between the injected current and voltage to Angle1 + 90. Check
that the monitored active power is equal to 0% of rated power and that the reactive
power is equal to 100% of rated power.
Change the angle between the injected current and voltage back to 0. Decrease the
current slowly until the START1 signal is activated. Check the injected power and
compare to the set value Power1.
Increase the current to IBase.
Switch the current off and measure the lime for activation of TRIP1.
If a second step is used: repeat points 2 6 for the second step.
Completing the test

purposes.
REC 670 ANSI

139
Section 12
12.5.12
Directional overpower protection (PDOP)

12.5.12.1

The overpower protection shall be set to values according to the real set values to be used.
The test is made by means of injection of voltage and current where the amplitude of both
current and voltage and the phase angle between the voltage and current can be controlled.
During the test the analog outputs of active and reactive power shall be monitored.
Procedure
1.
Connect the test set for injection of voltage and current corresponding to the measure
mode to be used in the application. If a three phase test set is available this could
be used for all the measure modes. If a single phase current/voltage test set is
available the test set should be connected to a selected input for one phase current
and voltage.
A, B, C
S = V A I A* + VB I B* + VC I C *
Arone
S = V AB I A* - VBC IC *
PosSeq
S = 3 VPosSeq I PosSeq*
AB
S = VAB ( I A* - I B* )
BC
S = VBC ( I B* - IC * )
CA
S = VCA ( I C * - I A* )
140

REC 670 ANSI
Section 12
S = 3 VA I A*
B
S = 3 VB I B*
C
S = 3 VC I C *
2.
3.
4.
5.
6.
7.
12.5.12.2
Adjust the injected current and voltage to the set rated values IBase and VBase
(converted to secondary current and voltage). The angle between the injected current
and voltage shall be set equal to the set direction Angle1 (equal to 180 for reverse
power protection). Check that the monitored active power is equal to 100% of rated
power and that the reactive power is equal to 0% of rated power.
Change the angle between the injected current and voltage to Angle1 + 90. Check
that the monitored active power is equal to 0% of rated power and that the reactive
power is equal to 100% of rated power.
Change the angle between the injected current and voltage back to Angle1 value.
Increase the current slowly from 0 until the START1 signal is activated. Check the
injected power and compare to the set value Power1.
Increase the current to IBase and switch the current off.
Switch the current on and measure the lime for activation of TRIP1.
If a second step is used: repeat points 2 6 for the second step.
Completing the test

purposes.
12.5.13
Broken conductor check (BRC)

12.5.13.1
Measuring the operate and time limit of set values

Procedure
REC 670 ANSI

141
Section 12
1.
Check that the input logical signal BRC-BLOCK is logical zero and note on the
local HMI that the BRC-TRIP logical signal is equal to the logical 0.
Values of the logical output signals belonging to the broken conductor check
function are available under menu tree:
Test/Function Status/Current protection/ Broken Cond Check
2. Set the measured current (fault current) in one phase to about 110% of the set
operating current (IP>).
Observe the maximum permitted overloading of the current circuits in the terminal.
3. Switch on the fault current and measure the operating time of the BRC protection.
Use the BRC--TRIP signal from the configured binary output to stop the timer.
4. Compare the measured time with the set value tOper.
5. Activate the BRC--BLOCK binary input.
6. Switch on the fault current (110% of the setting) and wait longer than the set value
tOper.
No BRC--TRIP signal should appear.
7. Switch off the fault current.
8. Set the measured current (fault current) in same phase to about 90% of the set
operating current. Switch off the current.
9. Switch on the fault current and wait longer than the set value tOper.
No BRC--TRIP signal should appear.
10. Switch off the fault current.
12.5.13.2
Completing the test

purposes.
12.6
Voltage protection
12.6.1
Two step undervoltage protection (PTUV, 27)

12.6.1.1

Verification of StartPickup-value and time delay to operate for Step1
Procedure
142

REC 670 ANSI
Section 12
1.
2.
3.
4.
5.
6.
7.
8.
Make sure that the IED settings are appropriate, especially the Pickup-value, the
definite time delay and the 1 out of 3 operation mode.
Supply the terminal with three-phase voltages at their rated values.
Slowly decrease the voltage in one of the phases, until the PICKUP signal appears.
Note the operate value and compare it with the set value.
Increase the measured voltage to rated load conditions.
Make sure that the PICKUP signal resets.
Instantaneously decrease the voltage in one-phase to a value about 20% lower than
the measured operate value.
Measure the time delay for the TRIP signal, and compare it with the set value.
Extended testing
Procedure
1.
2.
3.
4.
5.
12.6.1.2
The test above can now be repeated for Step2.

The tests above can be repeated for 2 out of 3 and for 3 out of 3 operation mode.
The tests above can be repeated to check security, i.e. the pickup and operate signals,
that are not supposed to appear, - do not.
The tests above can be repeated to check the time to reset.
The tests above can be repeated to test the inverse time characteristic.
Completing the test

Restore connections and settings to their original values, if they were changed for test
purposes.
12.6.2
Two step overvoltage protection (PTOV, 59)

12.6.2.1

Procedure
1.
2.
3.
4.
REC 670 ANSI
Apply single phase voltage below the set value Pickup1.

Slowly increase the voltage until the PU_ST1 signal appears.
Switch the applied voltage off.

143
Section 12
5.
6.
7.
12.6.2.2
Set and apply about 20% higher voltage than the measured operate value for one
phase.
Measure the time delay for the TRST1 signal and compare it with the set value.
Repeat the test for step 2.
Completing the test

purposes.
12.6.3
Two step residual overvoltage protection (PTOV, 59N)

12.6.3.1

Procedure
1.
2.
3.
4.
5.
6.
7.
12.6.3.2
Apply the single phase voltage either to a single phase voltage input or to a residual
voltage input with the pickup value below the set value Pickup1
Slowly increase the value until PU_ST1 appears
Switch the applied voltage off.
Set and apply about 20% higher voltage than the measured operate value for one
phase.
Measure the time delay for the TRST1 signal and compare it with the set value.
Repeat the test for step 2.
Completing the test

purposes.
12.6.4
Voltage differential protection (PTOV, 60)

144

REC 670 ANSI
Section 12
12.6.4.1
Check of undervoltage levels

This test is relevant if the setting BlkDiffAtVLow=Yes.
Check of V1Low
Procedure
Connect voltages to the IED according to valid connection diagram and figure 63.
Apply voltage higher than the highest set value of VDTrip, V1Low and V2Low to
the V1 three phase inputs and to one phase of the V2 inputs according to
figure 63.
The voltage differential PICKUP signal is set.
VA
VA
VB
VB
VC
VC
VN
VN
VA
VB
VC
IED 670
RELAY TEST SET
1.
2.
en07000106_ansi.vsd
Figure 63:
Connection of the test set to the IED for test of V1 block level
where:
3.
4.
5.
REC 670 ANSI
is three phase voltage group1 (V1)
Decrease slowly the voltage in phase VL1 of the test set until the PICKUP signal
resets.
Check V1 blocking level by comparing the voltage level at reset with the set
undervoltage blocking V1Low.
Repeat steps 2 to 4 to check V1Low for the other phases.

145
Section 12
The connections to V1 must be shifted to test another phase. (VL1

to VL2, VL2 to VL3, VL3 to VL1)
Check ofV2Low
Procedure
VA
VA
VB
VB
VC
VC
VN
VN
VA
VB
VC
IED 670
RELAY TEST SET
1.
en07000107_ansi.vsd
Figure 64:
Connection of the test set to the IED for test of V2 block level
where:
2.
3.
4.
146
Apply voltage higher than the highest set value of VDTrip, V1Low and V2Low to
the V1 three phase inputs and to one phase of the V2 inputs according to
figure 64.
The voltage differential PICKUP signal is set.
Decrease slowly the voltage in phase VL3 of the test set until the PICKUP signal
resets.
Check V2 blocking level by comparing the voltage level at reset with the set
undervoltage blocking V2Low.

REC 670 ANSI
Section 12
12.6.4.2
Check of voltage differential trip and alarm levels

Procedure
VA
VA
VB
VB
VC
VC
VN
VN
VA
VB
VC
IED 670
RELAY TEST SET
1.
en07000108_ansi.vsd
Figure 65:
Connection of the test set to the IED for test of alarm levels, trip
levels and trip timer
where:
2.
3.
Apply 1.2 * Vn (rated voltage) to the V1 and V2 inputs.

Decrease slowly the voltage of in phase VL1 of the test set until the ALARM signal
is activated.
The ALARM signal is delayed with timer tAlarm
4.
REC 670 ANSI
Check the alarm operation level by comparing the differential voltage level at
ALARM with the set alarm level VDAlarm.

147
Section 12
5.
6.
7.
12.6.4.3
Continue to slowly decrease the voltage until PICKUP signal is activated.

Check the differential voltage operation level by comparing the differential voltage
level at PICKUP with the set trip level VDTrip.
Repeat steps 1 to 2 to check the other phases.
Observe that the connections to V1 must be shifted to test another phase. (VL1 to
VL2, VL2 to VL3, VL3 to VL1)
Check of trip and trip reset timers

Procdure
1.
2.
3.
4.
5.
6.
12.6.4.4
Set Vn (rated voltage) to the V1 inputs and increase V2 voltage until differential
voltage is 1.5 x operating level (UDTrip).
Switch on the test set. Measure the time from activation of the PICKUP signal until
TRIP signal is activated.
Check the measured time by comparing it to the set trip time tTrip.
Increase the voltage until PICKUP signal resets. Measure the time from reset of
PICKUP signal to reset of TRIP signal.
Check the measured time by comparing it to the set trip reset time tReset.
Final adjustment of compensation for VT ratio differences

Procedure
1.
With the protection in test mode, view the the differential voltage service values in
each phase.
LHMI path to the differential voltage values is:
Test/Function status/Voltage protection/VoltageDiff(PTOV,60)/VDCn
The IED voltage inputs should be connected to the VTs according
to valid connection diagram.
2.
3.
4.
5.
148
Record the differential voltages.

Calculate the compensation factor RF_x for each phase.
For information about calculation of the compensation factor, see the application
manual.
Set the compensation factors.
Path in LHMI is:
Settings/Settings group N/Voltage protection/VoltageDiff(PTOV,60)/VDCn
Check that the differential voltages are close to zero.

REC 670 ANSI
Section 12
12.6.4.5
Completing the test

purposes.
12.6.5
Loss of voltage check (LOV)

12.6.5.1

Procedure
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
REC 670 ANSI
Check that the input logical signals LOV-BLOCK, LOV-CBOPEN and LOVVTSU are logical zero.
Supply a three phase rated voltage in all three phases and note on the local HMI that
the LOV-TRIP logical signal is equal to the logical 0.
Logical output signals for loss of voltage check protection are available under menu
tree:
Test / Function status/Voltage Protection/ Loss of Voltage
Switch off the voltage in all three phases.
After set ttrip time a LOV-TRIP signal appears on the corresponding binary output
or on the local HMI. Note that LOV--TRIP at this time is a pulse signal, duration
should be according to set tpulse.
Inject the measured voltages to their rated values for at least set tRestore time.
Activate the LOV-CBOPEN binary input.
Simultaneously disconnect all the three phase voltages from the IED.
No LOV-TRIP signal should appear.
Activate the LOV-VTSU binary input.
Simultaneously disconnect all the three phase voltages from the tRestore.
Reset the LOV-VTSU binary input.
Activate the LOV-BLOCK binary input.
Simultaneously disconnect all the three phase voltages from the terminal.
Reset the LOV-BLOCK binary input.
off.

149
Section 12
12.6.5.2
Completing the test

purposes.
12.7
Frequency protection
12.7.1
Underfrequency protection (PTUF, 81)

12.7.1.1

Verification of Pickup-value and time delay to operate
Procedure
1.
2.
3.
4.
5.
6.
7.
8.
Make sure that the IED settings are appropriate, especially the Pickup-value and the
definite time delay.
Slowly decrease the frequency of the applied voltage, until the PICKUP signal
appears.
Increase the frequency until rated operating levels are reached.
Instantaneously decrease the frequency of the applied voltage to a value about 20%
lower than the operate value.
Measure the time delay of the TRIP signal, and compare it with the set value.
Extended testing
Procedure
1.
2.
The test above can be repeated to check the time to reset.

The tests above can be repeated to test the voltage dependent inverse time
characteristic.
Verification of the low voltage magnitude blocking

Procedure
150

REC 670 ANSI
Section 12
1.
2.
3.
4.
5.
6.
7.
12.7.1.2
Make sure that the IED settings are appropriate, especially the PickupFrequency,
IntBlkPuVal, and the tTrip.
Supply the terminal with three-phase voltages at rated values.
Slowly decrease the magnitude of the applied voltage, until the BLKDMAGN signal
appears.
Note the voltage magnitude value and compare it with the set value, IntBlkPuVal.
Slowly decrease the frequency of the applied voltage, to a value below
PUFrequency.
Make sure that the PICKUP signal not appears.
Wait for a time corresponding to tTrip, and make sure that the TRIP signal not
appears.
Completing the test

Continue to test another function or end the test session by changing the test mode setting
to off. Restore connections and settings to their original values, if they were changed for
test purposes.
12.7.2
Overfrequency protection (PTOF, 81)

12.7.2.1

Procedure
1.
2.
3.
4.
5.
6.
7.
8.
REC 670 ANSI
Make sure that you have appropriate settings in the terminal, especially the
Pickup-value and the definite time delay.
Slowly increase the frequency of the applied voltage, until the PICKUP signal
appears.
Decrease the frequency to rated operating conditions.
Instantaneously increase the frequency of the applied voltage to a value about 20%
higher than the operate value.

151
Section 12
Extended testing
Procedure
1.
The test above can be repeated to check the time to reset.
Verification of the low voltage magnitude blocking

Procedure
1.
2.
3.
4.
5.
6.
7.
12.7.2.2
Make sure that you have appropriate settings in the terminal, especially the
PUFrequency, IntBlkPuVal, and the tTrip.
Slowly decrease the magnitude of the applied voltage, until the BLKDMAGN signal
appears.
Note the voltage magnitude value and compare it with the set value, IntBlkPuVal.
Slowly increase the frequency of the applied voltage, to a value above
PUFrequency.
Make sure that the PICKUP signal not appears.
Wait for a time corresponding to tTrip, and make sure that the TRIP signal does not
appears.
Completing the test

purposes.
12.7.3
Rate-of-change frequency protection (PFRC, 81)

12.7.3.1

Procedure
152

REC 670 ANSI
Section 12
1.
2.
3.
4.
5.
6.
7.
8.
Make sure that you have appropriate settings in the terminal, especially the -value
and the definite time delay. Set PUFreqgrad, to a rather small negative value.
Slowly decrease the frequency of the applied voltage, with an increasing rate-ofchange that finally exceeds the setting of PUFreqgrad, and check that the
PICKUP signal appears.
Increase the frequency to rated operating conditions, and zero rate-of-change.
Instantaneously decrease the frequency of the applied voltage to a value about 20%
lower than the nominal value.
Extended testing
Procedure
1.
2.
3.
12.7.3.2
The test above can be repeated to check a positive setting of PUFreqGrad.

The tests above can be repeated to check the time to reset.
The tests above can be repeated to test the RESTORE signal, when the frequency
recovers from a low value.
Completing the test

purposes.
12.8
Multipurpose protection
12.8.1
General current and voltage protection (GAPC)

One of the new facilities within the GF function is that the value which is processed and
used for evaluation in the function can be chosen in many different ways by the setting
parameters CurrentInput and VoltageInput.
These setting parameters decide what kind of preprocessing the connected three-phase
CT and VT inputs shall be subjected to. That is e.g. single-phase quantities, phase-tophase quantities, positive sequence quantities, negative sequence quantities, maximum
quantity from the 3-phase group, minimum quantity from the 3-phase group, difference
REC 670 ANSI

153
Section 12
between maximum and minimum quantities (unbalance) can be derived and then used in
the function.
Due to the versatile possibilities of the GF itself but also the possibilities of logic
combinations in the CAP-configuration of outputs from more then one GF function block
it is hardly possible to define a fully covering general commissioning test.
12.8.1.1
Built-in overcurrent feature (non-directional)

Procedure
1.
Go to the Test/Function Test Mode/Multipurpose protection menu and make sure

that the GF to be tested is unblocked and other functions that might disturb the
evaluation of the test are blocked.
2. Connect the test set for injection of 3-phase currents to the appropriate current
terminals of IED 670.
3. Inject current(s) in a way that relevant measured current (according to setting
parameter CurrentInput) is created from the test set. Increase the current(s) until the
low set stage operates and check against the set operate value.
4. Decrease the current slowly and check the reset value.
5. Block high set stage if the injection current will activate the high set stage when
testing the low set stage according to below.
6. Connect a trip output contact to the timer.
7. Set the current to 200% of the operate value of low set stage, switch on the current
and check the time delay.
For inverse time curves, check the operate time at a current equal to 110% of the
operate current at t_MinTripDelay.
8. Check that trip and pickup contacts operate according to the configuration logic.
9. Release the blocking of the high set stage and check the operate and reset value and
the time delay for the high set stage in the same way as for the low set stage.
10. Finally check that pickup and trip information is stored in the Event menu.
Information on how to use the event menu is found in the IED 670 operators manual.
12.8.1.2
Overcurrent feature with current restraint

The current restraining value has also to be measured or calculated and the influence on
the operation has to be calculated when the testing of the operate value is done.
Procedure
1.
154
Operate value measurement

REC 670 ANSI
Section 12
The current restraining value has also to be measured or calculated and the influence
on the operation has to be calculated when the testing of the operate value is done.
12.8.1.3
Overcurrent feature with voltage restraint

Procedure
1.
2.
3.
4.
12.8.1.4
Connect the test set for injection of 3-phase currents and 3-phase voltages to the
appropriate current and voltage terminals of IED 670.
Inject current(s) and voltage(s) in a way that relevant measured (according to setting
parameter CurrentInput and VoltageInput) currents and voltages are created from
the test set.
Overall check in principal as above (non-directional overcurrent feature)
Operate value measurement
The relevant voltage restraining value (according to setting parameter
VoltageInput) has also to be injected from the test set and the influence on the operate
value has to be calculated when the testing the operate value is done.
Operate time measurement
Definite times may be tested as above (non-directional overcurrent feature). For
inverse time characteristics the pickup value (to which the overcurrent ratio has to
be calculated) is the actual pickup value as got with actual restraining from the
voltage restraining quantity.
Overcurrent feature with directionality

Please note that the directional characteristic can be set in two different ways either just
dependent on the angle between current and polarizing voltage (setting parameter
DirPrinc_OC1 or Dirprinc_OC2 set to or in a way that the operate value also is dependent
on the angle between current and polarizing voltage according to the I x cos(F) law
(setting parameter DirPrincOC1 or DirPrincOC2 set to I x cos(F). This has to be known
if a more detailed measurement of the directional characteristic is made, than the one
described below.
Procedure
1.
2.
3.
REC 670 ANSI
Connect the test set for injection of 3-phase currents and 3-phase voltages to the
appropriate current and voltage terminals of IED 670.
Inject current(s) and voltage(s) in a way that relevant measured (according to setting
parameter CurrentInput and VoltageInput) currents and voltages are created from
the test set.
Set the relevant measuring quantity current to lag or lead (lag for negative rca angle
and lead for positive rca angle) the relevant polarizing quantity voltage by an angle

155
Section 12
4.
5.
6.
12.8.1.5
equal to the set relay characteristic angle (rca-dir) when forward directional feature
is selected and the CTstarpoint configuration parameter is set to ToObject.
If reverse directional feature is selected or CTstarpoint configuration parameter is
set to FromObject the angle between current and polarizing voltage shall be set
equal to rca-dir+180.
Overall check in principal as above (non-directional overcurrent feature)
Reverse the direction of the injection current and check that the protection does not
operate.
Check with low polarization voltage that the feature becomes non-directional,
blocked or with memory according to the setting.
Over/Undervoltage feature
Procedure
1.
2.
3.
12.8.1.6
Connect the test set for injection 3-phase voltages to the appropriate voltage
terminals of IED 670.
Inject voltage(s) in a way that relevant measured (according to setting parameter
VoltageInput) voltages are created from the test set.
Overall check in principal as above (non-directional overcurrent feature) and
correspondingly for the undervoltage feature.
Completing the test

purposes.
12.9
Secondary system supervision
12.9.1
Current circuit supervision (RDIF)

The current circuit supervision function is conveniently tested with the same 3-phase test
set as used when testing the measuring functions in the IED 670.
The condition for this procedure is that the setting of IMinOp is lower than the setting of
Pickup_Block
156

REC 670 ANSI
Section 12
12.9.1.1

Procedure
1.
2.
3.
4.
12.9.1.2
Check the input circuits and the operate value of the IMinOp current level detector
by injecting current, one phase at a time
Check the phase current blocking function for all three phases by injection current,
one phase at a time. The output signals shall reset with a delay of 1 second when
the current exceeds 1.5*IBase
Inject a current 0.9*IBase to phase A and a current 0.15*IBase to the reference
current input I5
Decrease slowly the current to the reference current input and check that blocking
is obtained when the current is about 0.1*IBase
Completing the test

purposes.
12.9.2
Fuse failure supervision (RFUF)

The verification is divided in two main parts. The first part is common to all fuse failure
supervision options, and checks that binary inputs and outputs operate as expected
according to actual configuration. In the second part the relevant set operate values are
measured.
The corresponding binary signals that inform the operator about the operation of the
FUSE function are available on the local HMI under the menu:
Test/Function status/Secondary System Supervision/FuseFailure(RFUF)/FSO
12.9.2.1
Checking that the binary inputs and outputs operate as expected

Procedure
1.
2.
REC 670 ANSI
Simulate normal operating conditions with the three-phase currents in phase with
their corresponding phase voltages and with all of them equal to their rated values.
Connect the nominal dc voltage to the 89bS binary input.

157
Section 12
3.
4.
The signal BLKV should appear with almost no time delay.

No signals BLKZ and 3PH should appear on the IED.
Only the distance protection function operates.
No other undervoltage-dependent functions must operate.
Disconnect the dc voltage from the 89b binary input terminal.

Connect the nominal dc voltage to the MCBOP binary input.
5.
6.
7.
The BLKV and BLKZ signals should appear without any time delay.
No undervoltage-dependent functions must operate.
Disconnect the dc voltage from the MCBOP binary input terminal.

Disconnect one of the phase voltages and observe the logical output signals on the
terminal binary outputs.
After more than 5 seconds disconnect the remaining two phase voltages and all three
currents.
There should be no change in the high status of the output signals BLKV and
BLKZ.
The signal 3PH will appear.
8.
Establish normal voltage and current operating conditions simultaneously and

observe the corresponding output signals.
They should change to logical 0 as follows:
12.9.2.2
Signal 3PH after about 25 ms

Signal BLKV after about 50 ms
Signal BLKZ after about 200 ms
Measuring the operate value for the negative sequence function

Measure the operate value for the negative sequence function, if included in the IED.
Procedure
1.
2.
3.
Slowly decrease the measured voltage in one phase until the BLKV signal appears.
Record the measured voltage and calculate the corresponding negative-sequence
voltage according to the equation.
Observe that the voltages in the equation are phasors:
2
3 V2 = VA + a VB + a VC
(Equation 20)
Where:
V A VB and VC
158

= the measured phase voltages
REC 670 ANSI
Section 12
a = 1e
4.
12.9.2.3
2p
j ----------3
3
= 0, 5 + j ------2
Compare the result with the set value (consider that the set value 3V2PU is in
percentage of the base voltage U1b) of the negative-sequence operating voltage.
Measuring the operate value for the zero sequence function

Measure the operate value for the zero sequence function, if included in the IED.
Procedure
1.
2.
3.
Slowly decrease the measured voltage in one phase until the BLKV signal appears.
Record the measured voltage and calculate the corresponding zero-sequence voltage
according to the equation.
Observe that the voltages in the equation are phasors.
3 V0 = V A + VB + VC
(Equation 23)
Where:
V A VB and VC
4.
12.9.2.4
= the measured phase voltages.
Compare the result with the set value (consider that the set value 3V0Pickup is in
percentage of the base voltage of the zero-sequence operating voltage.
Checking the operation of the duv/dt and di/dt based function

Check the operation of the dv/dt and di/dt based function, if included in the IED.
Procedure
1.
2.
3.
REC 670 ANSI
Connect the nominal dc voltage to the 52a binary input.
Change the voltages and currents in all three phases simultaneously.
The voltage change should be greater then setDVPU and the current change should
be less than the set DIPU.

159
Section 12
The BLKV and BLKZ signals appear without any time delay. The BLKZ
signal will be activated , only if the internal deadline detection is not activated
at the same time.
3PH should appear after 5 seconds, if the remaining voltage levels are lower
than the set VDLDPU of the DLD function.
Apply normal conditions as in step 1 .

The BLKV, BLKZ and 3PH signals should reset, if activated, see step 3 .
5. Change the voltages and currents in all three phases simultaneously.
The voltage change should be greater then set DVPU and the current change should
be greater then the set DIPU.
The BLKV, BLKZ and 3PH signals should not appear.
6. Disconnect the dc voltage to the 52a binary input.
7. Apply normal conditions as in step 1 .
8. Repeat step 3 .
9. Connect the nominal voltages in all three phases and feed a current below the operate
level in all three phases.
10. Keep the current constant. Disconnect the voltage in all three phases simultaneously.
4.
12.9.2.5
Completing the test

purposes.
12.10
Control
12.10.1
Synchronism-check and energizing check (RSYN, 25)

This section contains instructions on how to test the synchronism and energizing check
for single and double CB with or without the synchronizing function and for breaker-anda-half arrangements.
Prepare the IED for verification of settings as outlined in section "Overview"and
At commissioning and periodical checks, the functions shall be tested with the used
settings. To test a specific function, it might be necessary to change some setting
parameters, for example:
160
AutoEnerg = On/Off/DLLB/DBLL/Both
ManEnerg = Off
Operation = Off, On
Activation of the voltage selection function if applicable

REC 670 ANSI
Section 12
The tests explained in the test procedures below describe the settings, which can be used
as references during testing before the final settings are specified. After testing, restore
the equipment to the normal or desired settings.
A secondary injection test set with the possibility to alter the phase angle by regulation
of the resistive and reactive components is needed. The test set must also be able to
generate different frequencies on different outputs.
The description below applies for a system with a nominal frequency of
60 Hz but can be directly transferred to 50 Hz. The synchronism-check
function can be set to use different phases, phase to earth or phase to phase.
Use the set voltages instead of what is indicated below.
Figure 66 shows the general test connection principle, which can be used during testing.
This description describes the test of the version intended for one bay.
Figure 67 shows the general test connection for a breaker-and-a-half diameter with onephase voltage connected to the line side.
REx670
Test
equipment
V-Bus
V-Bus
VMeasure
Ph/N
Ph/Ph
V-Line
VA
VB
VC
VN
Input Phase
A,B,C
AB,BC,CA
en05000480_ansi.vsd
Figure 66:
REC 670 ANSI
General test connection with three-phase voltage connected to the line

side

161
Section 12
REx670
Test
equipment
V-Bus1
V3PBB1
V-Bus2
V3PBB2
V-Line2
V3PL2
N
V-Line1
V3PL1
VMeasure
Ph/N
Ph/Ph
en05000481_ansi.vsd
Figure 67:
12.10.1.1
General test connection for a breaker-and-a-half diameter with onephase voltage connected to the line side
Testing the synchronizing function

This section is applicable only if the synchronizing function is included.
The voltage inputs used are:
V3PL1
VA, VB or VC voltage inputs on the IED
V3PBB1
Bus1 voltage input on the IED.
V3PBB2
Bus2 voltage input on the IED
V3PL2
VA, VB or VC voltage from line 2 inputs on the IED
The settings in table 19 shows typical values. The final settings should be used during
testing.
Table 19:
Test settings for synchronizing
Parameter
Setting
Operation
Off
VBase
System voltage level
SelPhaseBus1
VB
SelPhaseBus2
VB
162

REC 670 ANSI
Section 12
Parameter
Setting
SelPhaseLine1
VB
SelPhaseLine2
VB
PhaseShift
0 degrees
1.00
REC 670 ANSI
CBConfig
SingleBus
AutoEnerg
Off
ManEnerg
Off
ManEnergDBDL
Off
VLiveBusEnerg
80% VBase
VLiveLineEnerg
80% VBase
VDeadLineEnerg
30% VBase
VMaxEnerg
125% VBase
OperationSynch
On
VLiveBusSynch
70% VBase
VLiveLineSynch
70% VBase
VDiffSynch
15%VBase
FreqDiffMin
0.01 Hz
FreqDiffMax
0.22 Hz
tMaxSynch
600 sec
OperationSC
On
PhaseDiffM
35 degrees
PhaseDiffA
35 degrees
FreqDiffM
0.01 Hz
FreqDiffA
0.01 Hz
VDiff
15% VBase
tAutoEnerg
0.1 s
tManEnerg
0.1 s
ShortPulse
Off
tClosePulse
0.20 s
tBreaker
0.08 s
VTConnection
Line
tSyncM
0s
tSyncA
0s
FreqDiffBlock
Off

163
Section 12
Testing the frequency difference
The frequency difference is in the example set at 0.20 Hz on the local HMI, and the test
should verify that operation is achieved when the FreqDiffSynch frequency difference is
lower than 0.20 Hz. The test procedure below will depend on the settings used.
Procedure
1.
2.
3.
4.
5.
12.10.1.2
Apply voltages V-line = 100% VBase, f-line=60.0 Hz and V-Bus = 100% VBase,
f-bus = 60.2 Hz.
Check that a closing pulse is submitted and at closing angle less than 2 degrees from
phase equality. Modern test sets will evaluate this automatically.
Repeat with V-Bus = 80% VBase, f-bus=60.25 Hz to verify that the function does
not operate when freqency difference is above limit.
Repeat with different frequency differences e.g. 100 mH with f-bus nominal and
line leading and for example 20 mHz (or just above fSynMin) to verify that
independent of frequency difference the closing pulse occurs within 2 degrees.
Verify that the closing command is not issued when the frequency difference is less
than the set value fSynMin.
Testing the synchronism check

During test of the synchronism check function for a single bay arrangement, these voltage
inputs are used:
V-line
VA, VB or VC voltage input on the IED.
V-bus
V5 voltage input on the IED
Voltage inputs
At test of the synchronism-check function for a breaker-and-a-half diameter the following

alternative voltage inputs can be used for the three synchronism-check functions. The
voltage is selected by activation of different inputs in the voltage selection logic:
SYN1
SYN2
V-line
VA
Activate SYN1_FD1CLD
VB
Activate SYN1_CB2CLD
V4
Activate SYN1_CB2CLD and CB3CLD
V-bus
V5
No activation of inputs necessary
V-line
UL2
V4
VA
V5
VA
V-bus
SYN3
V-line
164

REC 670 ANSI
Section 12
V-bus
VB
V5
Activate SYN3_CB1CLD and CB2CLD
V4
No activation of inputs necessary
Testing the voltage difference
Set the voltage difference at 15% VBase on the HMI, and the test should check that
operation is achieved when the voltage difference VDiff is lower than 15% VBase.
The settings used in the test shall be final settings. The test shall be adapted to site setting
values instead of values in the example below.
Test with no voltage difference between the inputs.
Test with a voltage difference higher than the set VDiffSCV
1.
2.
3.
4.
5.
Apply voltages V-line (e.g.) = 80% VBase and V-Bus = 80% VBase.
Check that the AUTOENOK and MANENOK outputs are activated.
The test can be repeated with different voltage values to verify that the function
operates within the set VDiffvalues. Check with both V1 and V2 respectively lower
than the other.
Increase the V-bus to 110% VBase, and the V-line = 90% VBase and also the
opposite condition.
Check that the two outputs for manual and auto synchronism are not activated.
Testing the phase angle difference
The phase angle differences PhaseDiffM and PhaseDiffA respectively are set to their final
settings and the test should verify that operation is achieved when the phase angle
difference is lower than this value both leading and lagging.
Test with no voltage difference
1.
2.
REC 670 ANSI
Apply voltages V-line (e.g.) = 100% and V-bus = 100% VBase, with a phase
difference equal to 0 degrees and a frequency difference lower than fSynchMax.
Check that the AUTOOK and MANOK outputs are activated.
The test can be repeated with other PhaseDiff values to verify that the function
operates for values lower than the set ones. By changing the phase angle on V1
connected to V-bus, between d degrees. The user can check that the two outputs
are activated for a PhaseDiff lower than the set value. It should not operate for other
values. See figure 68.

165
Section 12
V-Bus
No operation
+dj
V-Line operation
-dj
V-Bus
en05000551_ansi.vsd
Figure 68:
3.
Test of phase difference.
Change the phase angle between +d and d and verify that the two outputs are
activated for phase differences between these values but not for phase differences
outside, see figure 68.
Testing the frequency difference
The frequency difference test should verify that operation is achieved when the
FreqDiff frequency difference is lower than the set value for manual and auto
synchronism check respectively and that operation is blocked when the frequency
difference is bigger.
Test with FreqDiff = 0 mHz
Test with a frequency difference outside the set limits for manual and auto sychronism
check respectively.
1.
2.
3.
4.
Apply voltages V-Line equal to 100% VBase and V-Bus equal to 100%
UBaseVBase, with a frequency difference equal to 0 mHz and a phase difference
lower than the set value.
Check that the AUTOSYOK and MANSYOK outputs are activated.
Apply voltage to the U-line equal to 100% VBase with a frequency equal to 50 Hz
and voltage V-bus equal to 100% VBase, with a frequency outside the set limit.
Check that the two outputs are not activated.
The test can be repeated with different frequency values to verify that the function
operates for values lower than the set ones. If a modern test set is used, the frequency
can be changed continuously.
Testing the reference voltage

Procedure
1.
166
Use the same basic test connection as in figure 66.

REC 670 ANSI
Section 12
2.
3.
4.
12.10.1.3
The VDiff between the voltage connected to V-bus and V-line should be 0%, so that
the AUTOOK and MANOK outputs are activated first.
Change the V-Line voltage connection to V-Line2 without changing the setting on
the local HMI.
Check that the two outputs are not activated.
The test can also be repeated by moving the V-line voltage to the V3PL input.
Testing the energizing check

During test of the energizing check function for a single bay arrangement, these voltage
inputs are used:
V-line
VA, VB or VC voltage input on the terminal.
V-bus
V5 voltage input on the terminal
General
At test of the energizing check function for the applicable bus, arrangement shall be done
for the energizing check functions. The voltage is selected by activation of different inputs
in the voltage selection logic.
The test shall be performed according to the settings for the station. Test the alternatives
below that are applicable.
Testing the dead line live bus (DLLB)
The test should verify that the energizing check function operates for a low voltage on
the V-Line and for a high voltage on the V-bus. This corresponds to the energizing of a
dead line to a live bus.
Procedure
1.
2.
3.
Apply a single-phase voltage 100% VBase to the U-bus, and a single-phase voltage
30% VBase to the V-line.
Increase the V-Line to 60% VBase and V-Bus to be equal to 100% VBase. The
outputs should not be activated.
The test can be repeated with different values on the V-Bus and the V-Line.
Testing the dead bus live line (DBLL)
the V-bus and for a high one the V-line. This corresponds to an energizing of a dead bus
from a live line.
Procedure
REC 670 ANSI

167
Section 12
1.
2.
3.
4.
5.
Verify the local HMI settings AutoEnerg or ManEnerg to be DBLL.

Apply a single-phase voltage of 30% VBase to the V-bus and a single-phase voltage
of 100% VBase to the U-line.
Decrease the V-line to 60% VBase and keep the U-bus equal to 30% VBase.
The outputs should not be activated.
The test can be repeated with different values on the V-bus and the V-line.
Testing both directions (DLLB or DBLL)

Procedure
1.
2.
3.
4.
5.
Verify the local HMI settings AutoEnerg or ManEnerg to be Both.

Apply a single-phase voltage of 30% VBase to the V-line and a single-phase voltage
of 100% VBase to the V-bus.
Change the connection so that the V-line is equal to100% VBase and the V-bus is
equal to 30% VBase.
The outputs should still be activated.
The test can be repeated with different values on the V-bus and the V-line.
Testing the dead bus dead line (DBDL)
both the U-bus and the U-line, i.e closing of the breaker in a non-energized system. Test
is valid only when this function is used.
Procedure
1.
2.
3.
4.
5.
6.
Verify the local HMI setting AutoEnerg to Off and ManEnerg to DBLL.
Set the parameter ManDBDL to On.
Apply a single-phase voltage of 30% VBase to the U-bus and a single-phase voltage
of 30% VBase to the V-line.
Check that the MANENOK output is activated.
Increase the V-bus to 80% VBase and keep the U-line equal to 30% VBase.
The outputs should not be activated.
Repeat the test with ManEnerg set to DLLB with different values on the V-bus and
the V-line voltage.
12.10.1.4
Testing the voltage selection
168

REC 670 ANSI
Section 12
Testing the voltage selection for single CB arrangements
This test should verify that the correct voltage is selected for the measurement in the
energizing check function used in a double-bus arrangement. Apply a single-phase
voltage of 30% VBase to the V-line and a single-phase voltage of 100% VBase to the Vbus.
If the VB1/2OK inputs for the fuse failure are used, they must be activated, during tests
below. Also verify that deactivation prevents operation and gives an alarm.
Procedure
1.
2.
Connect the signals below to binary inputs and binary outputs.

Connect the voltage inputs to the analog inputs used for each bus or line depending
of the type of busbar arrangement and verify that correct output signals are
generated.
Testing the voltage selection for double breaker or 1 circuit

breakerbreaker-and-a-half diameter when applicable
This test should verify that correct voltage is selected for the measurement in the
energizing function used for a diameter in a breaker-and-a-half arrangement. Apply
single-phase voltages to the inputs according to the table 19. H means a voltage of
100% VBase and L means a voltage of 30% VBase. Verify that correct output signals
are generated.
Procedure
1.
2.
3.
12.10.1.5
Connect the analog signals to the voltage inputs, in pair of two for V1 and V2.
(Inputs U3P - BB1, BB2, L1, L2)
Activate the binary signals according to the used alternative. Verify the measuring
voltage on the synchronism check function. Normally it can be good to verify
synchronism check with the same voltages and phase angles on both voltages. The
voltages should be verified to be available when selected and not available when
another input is activated so connect only one voltage transformer reference at each
time.
Record your voltage selection tests in a matrix table showing read values and
AUTOSYOK/MANSYOK signals to document the test performed.
Completing the test

purposes.
REC 670 ANSI

169
Section 12
12.10.2
Autorecloser (RREC, 79)

Verification of the automatic reclosing function can be considered to consist of two parts;
one part to verify the internal logic and timing of the function and one part to verify its
interaction with the protection system. This section deals with verification of the autoreclosing function itself. However it is practical to initiate the auto-reclosing function by
activating a protection function, e.g. by secondary injection tests.
Prepare the IED for verification of settings as outlined in the section "Overview" and
The purpose of verification before commissioning is to check that entered selections,
setting parameters and configuration render the intended result. The function is flexible
with many options and facilities. At commissioning only the selections and settings
intended for use are verified. If one chooses to reduce some time settings in order to speed
up verification, be careful to set the parameters at intended operational values at the end
of the verification procedure. One such parameter is the reset time and could result in a
long delay of reclosing shots, e.g. shot 2 and later ones.
The verification test is performed together with protection and trip functions. Figure 69
illustrates a suggested testing arrangement, where the circuit-breaker (CB) is simulated
by an external bi-stable relay (BR), for example a relay type RXMVB2 or RXMD or
Breaker Simulator of ABB. The following manual switches are used:
Switch or push-button to close (SC)

Switch or push-button to trip (ST)
Switch for CB ready condition (SRY)
If no bi-stable relay or breaker simulator is available, replace it with two self-reset

auxiliary relays and use a self-holding connection.
Use a secondary injection relay test set to operate the protection function. The test set
shall be switched off when a trip signal is given or when the BR comes to open position
to simulate real conditions.
The CB simulation can be made more elaborate, including simulation of the operating
gear condition, CBREADY of either the type ready for a Close-Open (CO) cycle, or the
type ready for an Open-Close -Open (OCO) cycle.
The CB condition CBREADY of a type, CO, shall be high (true) until a closing operation
is performed. It then goes low (false) for a recharging time of about 5 - 10 s. After that it
is high again.
A CB condition CBREADY of a type, OCO shall be high (true) before and during tripping
(Initiate reclosing). During tripping it goes low for a recharging time, e.g. 10 s. It may
170

REC 670 ANSI
Section 12
thus be low at the instant of reclosing. After each Open or Close operation it may need a
recharging period before it goes high again.
In the example of CB simulation arrangement, the CBREADY condition is simulated by
a manual switch, SRY.
Information and material for the verification:
REC 670 ANSI
Protection or control unit, Intelligent electronic device (IED), configured and with
settings entered.
Configuration diagram for the IED
Terminal diagram for the IED, or plant circuit diagram including the IED
Technical reference manual for the IED
Relay test set for secondary injection
Means to indicate, measure and record operation and times, e.g. an event recording
facility
A bi-stable relay (BR) or two auxiliary relays to simulate a CB
Two push-buttons (SC, ST) to operate the BR and a change-over switch (SRY) to
simulate CBREADY
Possibly a switch simulation the Synchronism check (SYNC) condition

171
BI
AR01 - CLOSE CMD
Trip
AR01 - CB 52a
AR01 - CB READY
IED
Section 12
BI
SRY
ST
SC
To test
set
BR
en04000202_ansi.vsd
Figure 69:
12.10.2.1
Simulating the CB operation by a bi-stable relay/breaker simulator and

manual switches
Preparation of the verification

Procedure
1.
172
Check the function settings.

In the HMI tree they are found under:
Settings/Setting Group N/Control/Autorecloser(RREC,79)

REC 670 ANSI
Section 12
2.
3.
4.
5.
12.10.2.2
If any timer settings are reduced to speed-up or facilitate the testing, they shall be
set to normal after testing. A temporary label on the unit can be a reminder to restore
normal settings after which a verification test should be performed.
Decide if a synchronism check (SYNC) shall be included in the test.
If SYNC as an internal function or external device is not operated by the injection,
it may be connected as a permanent high signal or controlled by a switch.
Read and make notes of the reclosing operation counters.
Local HMI tree:
Test/Function status/Control/Auto recloser/Autorecloser(RREC,79)
Possibly reset the counters to zero. Counters are reset in the RESET menu.
Make arrangements for the simulation of the CB, e.g. as in figure 69.
Make arrangements for indication, recording and time measurements.
The signals for ,52a, RI, CLOSECMD, READY and other relevant signals should
preferably be arranged for event recording with time tagging. If that is not possible,
other means of time measurement and recording should be arranged.
Switching the auto-reclosing function Enabled and Disabled

Procedure
1.
2.
3.
12.10.2.3
Set the Operation setting to Disabled and check the state.

Set the Operation setting to Enabled and check the state, including SETON and
AR-READY.
The CB should be closed and ready.
If external control Disabled/Enabled is connected, check that it works.
Set Operation to ExternalCtrl, and use that control to switch Enabled and
Disabled, and check the state of the function
Verifying the auto-reclosing function

Select the test cases to be run according to what is applicable to the particular application.
It may for instance be a) three-phase single-shot reclosing, b) two-shot reclosing or c)
single-phase and three-phase single shot reclosing. Below a case with single-phase and
three-phase single-shot reclosing is illustrated.
Procedure
1.
2.
3.
4.
REC 670 ANSI
Set Operation = Enabled.

If SYNC is not to be operated ensure that the SYNC input is activated. If the SYNC
function is to be included, ensure that it is supplied with the appropriate AC
quantities.
Simulate CB closed position by closing switch SC to make the BR relay pick-up.
Simulate CBREADY by closing the switch SRY, and leave it closed.

173
Section 12
5.
6.
7.
12.10.2.4
Inject AC quantities to give a trip, e.g. 1-pole trip, to the BR and to the RI input.
Observe and preferably record the operation. The BR relay shall trip and reclose
(pick-up). After reclosing, the SRY switch can be opened for about 5 s and then
closed again.
The auto-reclosing open time and the sequence should be checked, for example in
the event recording. Check also the operation indications (disturbance report) and
the operation counters.
Test/Function status/Control/Autorecloser(RREC,79)
Should the operation not be as expected, this should be investigated. It could be
caused by an inappropriate setting or missing condition such as CBREADY (or
SYNC at three-phase reclosing).
Repeat the sequence by simulating a permanent fault.
Shortly after the reclosing shot a new fault is applied. If a single-shot reclosing
program is selected, there shall be one reclosing operation and then blocking of the
auto-reclosing function for the set reset time.
Before a new reclosing sequence can be run, the CBREADY and 52a (CB closed)
must be set manually.
Repeat the sequence by simulating a three-phase transient and permanent faults, and
other applicable cases, such as signal to RI_HS and High-speed reclosing.
If just single-phase reclosing is selected, FirstShot=1ph, a check can be run to make
sure that a three-pole trip does not result in any reclosing. Other similar cases can
be checked as required.
Checking the reclosing conditions

When checking the influence of a releasing condition it is suggested to first run a sequence
with the condition fulfilled. When the condition signal is removed, and a new sequence
is run, it indicates that the result was due to the changed condition. In case of a blocking
signal the procedure should be similar. Start without the blocking or inhibit signal, and
then run a sequence with the blocking or inhibit signal added.
Checking the influence of the INHIBIT signal

Procedure
1.
2.
3.
Check that the auto-reclosing function is operative, e.g. by making a reclosing shot
without the INHIBIT signal.
Apply a fault and thereby a RI signal. At the same time, or during the open time,
apply a signal to the input INHIBIT.
Check that the reclosing sequence is interrupted and no reclosing takes place.
Check closing onto a fault

Procedure
1.
174
Check that the reclosing function is operative, e.g. by making a reclosing shot.

REC 670 ANSI
Section 12
2.
3.
4.
Keep the CBREADY signal high.

Set the breaker simulating relay BR in Open position.
Close the BR relay and apply immediately a fault and thereby a IR signal.
Check that no reclosing takes place.
Checking the influence of CB not ready for reclosing

Procedure
1.
2.
3.
Check that the auto-reclosing function is operative, e.g. by making a reclosing shot.
Keep the CB simulator BR closed. Remove the CBREADY signal by opening SRY.
Apply a fault and thereby a IRsignal.
Checking the influence of synchronism check (at three-phasepole

reclosing)
Procedure
1.
2.
3.
Check that the auto-reclosing function is operative, e.g. by making a three-pole

reclosing shot with the synchronism check condition.
Remove the SYNC signal.
Apply a fault causing three-phase trip and thereby a START and a TR3P signal.
Wait for the tSync time out limit.
Check that no reclosing is made.
Checking the response when auto-reclosing is Off

Procedure
1.
2.
3.
Check that the auto-reclosing function is operative, e.g. by making a reclosing shot.
Set the auto-reclosing Operation Off, e.g. by external control.
The output READY shall be low, and PREP3P shall be high.
Apply a fault and thereby a RI signal.
Testing auto-reclosing in a multi-breaker arrangement
The usual arrangement is to have an auto-reclosing function per circuit-breaker. They can
be in different CB related units (IEDs) or in a common unit. One auto-reclosing function
(Master) is set with Priority=High and the other (Slave) with Priority=Low. An
illustration of typical interconnections is shown in the Application manual, section
Autorecloser/Setting guidelines. The two functions can be checked individually by
carefully applying START, WAIT, and INHIBIT signals.
It is also possible to verify the two functions together by using CB simulating equipment
and two CB circuits. There should be interconnections from the Master to the Slave
REC 670 ANSI

175
Section 12
function; WFMASTER - WAIT, and UNSUCCL - INHIBIT, as shown in the picture

referred to above.
Completing the test
After the tests, restore the equipment to normal or desired state. Check the following
items in particular:
Procedure
1.
2.
3.
4.
12.10.2.5
Check the operation counters.

Reset the counters to zero, if that is the user's preference. The counter reset function
is found in the HMI under:
Reset/Reset counters/AutoRecloser(RREC,79)/ARnn
Restore settings that may have been modified for the tests back to normal.
Disconnect the test switch, CB simulating arrangement and test circuits.
Reconnect any links or connection terminals, which may have been opened for the
tests.
Reset indications, alarms and disturbance recordings.
Clearing of the disturbance report must be done via the PCM 600 using the
Disturbance handling tool.
Completing the test

purposes.
12.10.3
Apparatus control (APC)

The apparatus control function consists of four types of function blocks, which are
connected in a delivery-specific way between bays and to the station level. For that reason,
test the total function in a system, that is, either in a complete delivery system as an
acceptance test (FAT/SAT) or as parts of that system.
12.10.4
Interlocking
The interlocking function consists of a bay-level part and a station-level part. The
interlocking is delivery specific and is realized by bay-to-bay communication over the
station bus. For that reason, test the function in a system, that is, either in a complete
delivery system as an acceptance test (FAT/SAT) or as parts of that system.
176

REC 670 ANSI
Section 12
12.10.5
Voltage control (VCTR)

Single mode voltage control is based on a transformer configuration consists of one tap
changer on a single two winding power transformer.
Parallel voltage control, if installed, may be set to operate in Master Follower (MF) mode
or Minimise Circulating Current (MCC) mode. The commissioning tests for each parallel
control mode are addressed separately in the following procedure.
Secondary injection of load current (IL) and secondary bus voltage (UB) equivalent
quantities is required during installation and commissioning tests. The test consists
mainly of:
1.
2.
Increasing or decreasing the injected voltage or current at the analogue inputs of the
IED.
Checking that the corresponding command/s (Lower or Raise) are issued by the
voltage control function.
Setting confirmation is an important step for voltage control in the installation and
commissioning phase to ensure consistency of power systems base quantities, alarm/
blocking conditions and parallel control settings for each transformer control function.
Before starting any test, undertake the following general setting checks in the PCM 600
PST for single or parallel voltage control function:
Confirm power system base quantities I1Base, I2Base, VBase.
Setting Group Nn/Control/Transformer Voltage Control/VCPn/General

and
Setting Group Nn/Control/TransformerVoltageControl/TCMn
REC 670 ANSI
Ensure transformer settings are consistent with transformer data:

177
Section 12
Short circuit impedance. General Settings/Control/

TransformerVoltageControl/VCP1/Xr2
Transformer tap range. General Settings/Control/
TransformerVoltageControl/TCMn/LowVoltTap and HighVoltTap
OLTC code type OLTC method for digital feedback of tap position. General
Settings/Control/TransformerVoltageControl/TCMn/CodeType
OLTC pulse duration required length of pulse from RET 670 to OLTC.
Setting Group Nn/Control/TransformerVoltageControl/TCMn/
tPulseDur
Tap change timeout duration - effectively the maximum transformer tap change
time. Setting Group Nn/Control/TransformerVoltageControl/TCMn/
tTCTimeout
During the installation and commissioning, the behaviour of the VCTR

function for different tests may be governed by a parameter group
contained in
General Settings/Control/TransformerVoltageControl/VCP1
These parameter settings can cause a Total Block, Automatic Block or
Alarm for a variety of system conditions including over and under
voltage, over current & tap changer failure. It is important to review these
settings and confirm the intended response of the VCTR function for
different secondary injection tests.
Terminology
The busbar voltage VB is a shorter notation for the measured voltages Va, Vb, Vc or
Vij, where Vij is the phase-to-phase voltage, Vij = Vi -Vj, or Vi, where Vi is one single
phase to ground voltage.
IL is a shorter notation for the measured load current; it is to be used instead of the three
phase quantities Ia, Ib, Ic or the two phase quantities Ii and Ij, or single phase current Ii.
Also note that for simplicity PST menu structures included in the following procedure
are referred to universally as VCP1, for example,
Setting Group Nn/Control/TransformerVoltageControl/VCP1/t1 and t2l
For cases where single mode voltage control is implemented, the PST menu structure will
include VCS1 instead of the parallel designator VCP1
12.10.5.1
Secondary test
The VCTR function performs basic voltage regulation by comparing a calculated load
voltage (VL) against a voltage range defined by PST setting VDeadband (with upper and
178

REC 670 ANSI
Section 12
lower limits V2 and V1 respectively). The calculated load voltage VL represents the
secondary transformer bus voltage VB adjusted for Load Drop Compensation (LDC)
where enabled in PST settings. Note that when LDC is disabled, VB equals VL.
When the load voltage VL stays within the interval between V1 and V2, no action will
be taken.
If VL < V1 or VL > V2, a command timer will start which is constant time or inverse
time defined by PST setting t1 and t1Use. The command timer will operate while the
measured voltage stays outside the inner deadband (defined by PST setting
VDeadBandInner).
If VL remains outside of the voltage range defined by VDeadband and the command
timer expires, the VCTR will execute a Raise or Lower command to the transformer tap
changer. This command sequence will be repeated until VL is brought back within the
inner deadband range.
12.10.5.2
Check the activation of the Voltage Control Operation

Procedure
1.
Confirm Transformer Tap Control = On & Transformer Voltage Control = On
Direct tap change control
Setting Group Nn/Control/TransformerVoltageControl/TCMn/Operation
Automatic transformer voltage control
Setting Group Nn/Control/TransformerVoltageControl/VCP1/General/

Operation
2.
REC 670 ANSI
Enable Tap Command
General Settings/Control/TransformerVoltageControl/TCMn/EnabTapCmd
While the test set is connected to the IED but no voltage is applied, the VCTR
function will detect an under voltage condition that may result in an alarm or
blocking of the VCTR operation. These conditions will be shown on the IED built
in HMI.
Apply the corresponding voltage
Confirm the analogue measuring mode prior to undertaking secondary injection
(positive sequence, phase to phase or phase to earth). This measuring mode is
defined in
Setting Group Nn/Control/TransformerVoltageControl/VCP1/General/
MeasMode

179
Section 12
The application of nominal voltage Vset according to set MeasMode to the relays
should cause the alarm or blocking condition for undervoltage to reset.
12.10.5.3
Check normal voltage regulation function

Procedure
1.
2.
3.
4.
5.
6.
12.10.5.4
Review the settings for VDeadband (based on percentage of nominal bus voltage)
and calculate the upper (V2) and lower (V1) voltage regulation limits for which a
tap change command will be issued.
Review the expected time for first (t1) and subsequent (t2) tap change commands
from the VCTR function
Setting Group N1/Control/TransformerVoltageControl/VCP1/t1 and t2l
Lower the voltage 1% below V1 and wait for the issue of a Raise command from
the VCTR after the expiry of a constant or inverse time delay set by t1. Detection
of this command will involve locating the allocated binary output for a Raise pulse
command in the PCM 600 Signal Matrix (SMT) and monitoring a positive from this
output.
After the issue of the Raise command, return the applied voltage to Vset (nominal
value).
Raise the voltage 1% above the upper deadband limit V2 and wait for the issue of
a Lower command from the VCTR after the expiry of a constant or inverse time
delay set by t1. Detection of this command will involve locating the allocated binary
output for a Low pulse command in the PCM 600 Signal Matrix (SMT) and
monitoring a positive from this output.
Return the applied voltage to Vset.
Check the setting of UVBlock

Procedure
1.
Confirm the setting for VBlock, nominally at 80% of rated voltage.
2.
Confirm the VCTR function response to an applied voltage below VBlock, by

reviewing setting General Settings/Control/TransformerVoltageControl/
VCP1/UVBk that may cause an alarm, total or automatic block of the VCTR
function to be displayed on the built in HMI.
Apply a voltage slightly below VBlock and confirm the response of the VCTR
function.
3.
180

REC 670 ANSI
Section 12
12.10.5.5
Check the setting of parameter UVmin and UVmax

Procedure
1.
2.
3.
4.
12.10.5.6
Confirm the settings for Vmin & Vmax.

General Settings/Control/TransformerVoltageControl/VCP1/min or max
Confirm the VCTR function response to an applied voltage below VMin and above
Vmax, by reviewing settings General Settings/Control/
TransformerVoltageControl/VCP1/UVPartBk and General Settings/Control/
TransformerVoltageControl/VCP1/OVPartBk These conditions may cause an
alarm, total or automatic block of the VCTR function to be displayed on the built
in HMI.
Decrease the injected voltage slightly below the Vmin value and check for the
corresponding blocking or alarm condition on the built in HMI. For an alarm
condition, the voltage regulation function is not blocked and a Raise command
should be issued from the IED.
Increase the applied voltage slightly above the Vmax value and check for the
corresponding blocking or alarm condition on the built in HMI. For an alarm
condition, the voltage regulation function is not blocked and a Lower command
should be issued from the IED.
Overcurrent blocking
Procedure
1.
2.
3.
12.10.5.7
Confirm the setting for Iblock

General Settings/Control/TransformerVoltageControl/VCP1/Iblock
Confirm the VCTR function response to an applied current above IBlock, by
reviewing settings General Settings/Control/TransformerVoltageControl/
VCP1/OVPartBk This condition may cause an alarm, total or automatic block of
the VCTR function to be displayed on the built in HMI.
Inject a current higher than the Iblock setting and confirm the alarm or blocking
condition is present on the built in HMI. If an automatic or total blocking condition
occurs, change the applied secondary voltage and confirm that no tap change
commands are issued from the associated binary outputs. This situation can also be
confirmed through reviewing the Disturbance and Service reports on the built in
HMI.
Single transformer
Load Drop Compensation
Procedure
REC 670 ANSI

181
Section 12
1.
2.
3.
Confirm that OperationLDC is set to Enabled

Confirm settings for Rline and Xline
Calculate the expected Load Voltage VL (displayed as a measured value on the IED
HMI) based on secondary injection of transformer secondary voltage (VB = Vset)
and rated load current (IL = I2Base), in accordance with equation 25.
VL = VB - ( Rline + jXline ) IL
(Equation 25)
where:
VL, IL = Re(IL) + jlm(IL) are complex phase quantities
When all secondary phase-to-ground voltages are available, use the positive
sequence components of voltage and current. By seperation of real and imaginary
parts:
vl , re =vb , re - rline il , re + xline il , im
vl , im =vb , im - xline il , re - rline il , im
(Equation 26)
(Equation 27)
where:
vb
= complex value of the busbar voltage
il
= complex value of the line current (secondary side)
rline
= value of the line resistance
xline
= value of the line reactance
For comparison with the set point value, the modulus of UL are according to
equation 28.
VL =
4.
5.
6.
7.
182
( vl , re )
+ ( vl , im )
(Equation 28)
Inject voltage for VB equal to PST setting Vset.

Inject current equal to rated current I2Base.
Confirm on the HMI that service values for Bus Voltage and Load Current are equal
to injected quantities.
Confirm that the calculated value for Load Voltage, displayed on the IED HMI, is
equal to that derived through hand calculations.

REC 670 ANSI
Section 12
8.
With OperationLDC set to Enabled, the voltage regulation algorithm uses the
calculated value for Load Voltage as the regulating quantity to compare against
Vset and the voltage deadband limits VDeadband and VDeadbandinner.
9. While injecting rated current I2Base into the IED, inject a quantity for VB that is
slightly higher then Vset+|(Rline+jXLine)IL|. This will ensure that the regulating
voltage VL is higher than Vset, and hence no tap change command should be issued
from the IED.
10. Reduce the injected voltage for VB slightly below Vset+|(Rline+jXLine)IL| and
confirm that the calculated value for Load Voltage is below Vset and a tap change
command is issued from the IED.
12.10.5.8
Parallel voltage regulation

Master Follower voltage regulation
Procedure
1.
2.
For the transformers connected in the parallel group, confirm that OperationPAR
is set to MF.
For parallel operation, it is also recommended that settings be confirmed for parallel
group membership, governed by PST setting TnRXOP
Setting Group Nn/Control/Transformer Voltage Control/VCPn/ParCtrl
Within the PST configuration, the general parallel arrangement of transformers are
defined by settint TnRXOP to Enabled or Disabled. The following rules are
applicable on the function inputs T1RXOP T4RXOP. If terminal T1 and T2 are
connected, T1RXOP shall be set to Enabled in ATC2 and T2RXOP shall be set to
Enabled in ATC3, T2RXOP and T3RXOP to Enabled in ATC1 and so on.
The parameter corresponding to the own terminal must not be set.
T1RXOP should thus not be set in terminal T1, T2RXOPnot in
terminal T2, etc.
3.
4.
5.
6.
REC 670 ANSI
The lowest transformer number in the parallel group is by default set as the Master
confirm that this is the case by reviewing the local IED HMI.
tap change command will be issued from the Master transformer in the group.
from the Master transformer
Setting Group Nn/Control/TransformerVoltageControl/VCP1/t1 and t2l
Apply a voltage 1% below V1 and wait for the issue of a Raise command from the
VCTR after the expiry of a constant or inverse time delay set by t1. Detection of
this command will involve locating the allocated binary output for a Raise command

183
Section 12
7.
8.
9.
in the PCM 600 Signal Matrix (SMT) and monitoring a positive from this output.
Confirm the timing of this command correlates with the PST setting t1.
After the issue of the Raise command, confirm that all Follower transformers in the
group change tap in accordance with the command issued from the Master
transformer.
Inject a voltage VB for the Master transformer that is 1% above the upper deadband
limit V2 and wait for the issue of a Lower command from the VCTR after the expiry
of a constant or inverse time delay set by t2.
Confirm that all Follower Transformers in the group change tap in accordance with
this command.
Circulating current voltage regulation
This instruction for confirmation of circulating current voltage regulation assumes two
transformers in the parallel group. Setting confirmation through secondary injection
requires calculation of circulating currents for each transformer based on impedance
values and respective compensating factors, and is therefore more complex for greater
than two transformers.
Procedure
1.
2.
Confirm that OperationPAR is set to CC for the transformers in the parallel group.
Setting Group Nn/Control/Transformer Voltage Control/VCPn/ParCtrl
defined by setting TnRXOP to Enabled or Disabled. The following rules are
applicable on the function inputs T1RXOP - T4RXOP. If terminal T1 and T2 are
connected, T1RXOP shall be set to Enabled in ATC2 and T2RXOP shall be set to
Enabled in ATC1. If T1 - T3 are available T1RXOP and T2RXOP shall be set to
Enabled in ATC3, T2RXOP and T3RXOP to Enabled in ATC1 and so on.
T1RXOP should thus not be set in terminal T1, T2RXOP not in
terminal T2 etc.
3.
4.
5.
6.
184
tap change command will be issued from the Master transformer in the group.
from the Master transformer
Setting Group Nn/Control/TransformerVoltageControl/VCP1/t1 and t2
Inject a voltage VB equal to Vset for each transformer.
Inject a load current for Transformer 1 that is equal to rated load current I2Base and
a load current for Transformer 2 that is equal to 95% of rated load current I2Base.

REC 670 ANSI
Section 12
7.
8.
This will have the effect of producing a calculated circulating current that flows
from HV to LV side for Transformer 1 and LV to HV side for Transformer 2.
Confirm that a circulating current is measured on the IED local HMI that is equal
in magnitude to 5% of I2Base, with polarity as discussed in step "".
Confirm the PST settings for Ci (Compensation Factor) and Xi (Transformer Short
Circuit Impedance). Using these setting values and the measured quantity of
circulating current from the IED HMI (Icc_i), calculate the value for circulating
current voltage adjustment Vci.
Vdi = Ci Icc _ i Xi
(Equation 29)
The voltage regulation algorithm then increases (for transformer T2) or decreases
(for transformer T1) the measured voltage by Vdi and compares Vi against the
voltage deadband limits V1 and V2 for the purposes of voltage regulation.
Vi = VB + Vdi
9.
(Equation 30)
To cause a tap change, the calculated value for circulating current voltage
adjustment must offset the injected quantity for bus voltage VB so that Vi is outside
the voltage deadband created by setting VDeadBand. Expressed by equation 31 and
equation 32.
Vdi > V 2 - VB
VB = Vset
(for the purposes of this test procedure)
Therfore:
Ci Icc _ i Xi > V 2 - Vset
Icc _ i >
(V 2 - Vset )
( Ci Xi )
(Equation 33)
(Equation 34)
10. Using the PST settings for Vset, VdeadBand, C (Compensating factor) and Xr2
(transformer short circuit impedance) calculate the magnitude of Icc_i necessary to
cause a tap change command.
REC 670 ANSI

185
Section 12
11. Inject current equal to I2base for Transformer 1 and (I2Base - |Icc_i|) for
Transformer 2 so that the magnitude of calculated circulating current will cause a
Raise command to be issued for Transformer 2 and a Lower command for
Transformer 1. Magnitude and direction of circulating currents measured for each
transformer can be observed as service values on the IED local HMI and Raise/
Lower commands detected from the binary output mapped within SMT.
The voltage injection equal to Vset is required for both transformers
during this test.
12. Confirm that a tap change command is issued from the VCTR function to
compensate for the circulating current.
13. Injected currents can be reversed such that the direction of calculated circulating
currents change polarity, which will cause a Lower command for Transformer 2
and a Raise command for Transformer 1.
Circulating Current Limit

Procedure
1.
2.
3.
4.
5.
6.
7.
Confirm that OperationPAR is set to CC for each transformer in the parallel group.
Confirm that OperCCBlock is set to On for each transformer in the parallel group.
Review the setting for CircCurrLimit.
Review the setting for CircCurrBk to confirm whether a circulating current limit
will result in an Alarm state, Total Block or Automatic Block of the VCTR function.
Inject a voltage VB equal to Vset for each transformer.
Inject a load current for Transformer 1 that is equal to rated load current I2Base and
a load current for Transformer 2 that is 1% less than [I2Base (I2Base
CircCurrLimit)]
Confirm that the VCTR function responds in accordance with the setting for
CircCurrBk. Alarm and blocking conditions can be confirmed through interrogation
of the Event or Control menus on the IED local HMI.
VT Mismatch during Parallel Operation

Procedure
186

REC 670 ANSI
Section 12
1.
2.
3.
4.
5.
12.10.5.9
Confirm that OperationPAR is set to MF for each transformer in the parallel group.
Review the setting for VTMismatch and tVTMismatch.
Inject a voltage UB equal to Uset for Transformer 1 and a voltage less than [Vsset
(VTMismatch Vset)] for Transformer 2.
This condition should result in a VTMismatch which will mutually block the
operation of VCTR for all transformers connected in the parallel group, which can
be confirmed through interrogation of the local IED HMI.
Confirm that the VCTR function responds in accordance with the setting for
CircCurrBk.
Completing the test

purposes.
12.11
Scheme communication
12.11.1
Scheme communication logic for distance protection (PSCH,

85)
Check the scheme logic during the secondary injection test of the impedance or
overcurrent protection functions. For details see the ordering sheets for each particular
IED 670.
Activating the different zones verifies that the ZCS signal is issued from the intended
zones. The CS signal from the independent tripping zone must have a tSendMin minimum
time.
Check the tripping function by activating the CR and CR_GUARD inputs with the
overreaching zone used to achieve the PLTR_CRD signal.
It is sufficient to activate the zones with only one type of fault with the secondary injection.
12.11.1.1
Testing permissive underreach

Procedure
REC 670 ANSI

187
Section 12
1.
2.
3.
4.
5.
6.
7.
12.11.1.2
Activate the carrier receive (CR) signal in the IED.

Apply healthy normal load conditions to the IED for at least two seconds.
Apply a fault condition within the permissive zone.
Check that correct trip outputs, external signals, and indications are obtained for the
actual type of fault generated.
Check that other zones operate according to their zone timers and that the carrier
send (CS) signal is obtained only for the zone configured to generate the actual
signal.
Deactivate the carrier receive (CR) signal in the IED.
Check that the trip time complies with the zone timers and that correct trip outputs,
external signals, and indications are obtained for the actual type of fault generated.
Testing permissive overreach

Procedure
1.
2.
3.
4.
5.
6.
7.
8.
9.
12.11.1.3
Activate the carrier receive (CR) signal in the IED.

Check that correct trip outputs, external signals, and indication are obtained for the
actual type of fault generated.
Check that the other zones operate according to their zone timer and that the carrier
send (CS) signal is obtained only for the zones that are configured to give the actual
signal.
Deactivate the IED carrier receive (CR) signal.
Check that trip time complies with the zone timers and that correct trip outputs,
Testing blocking scheme

Procedure
1.
2.
3.
4.
5.
188
Deactivate the carrier receive (CR) signal of the IED.

Apply a fault condition within the forward directed zone used for scheme
communication tripping.
Check that correct trip outputs and external signals are obtained for the type of fault
generated and that the operate time complies with the tCoord timer (plus relaymeasuring time).
Check that the other zones operate according to their zone times and that a carrier
send (CS) signal is only obtained for the reverse zone.

REC 670 ANSI
Section 12
6.
7.
8.
9.
12.11.1.4
Activate the IED carrier receive (CR) signal.

Apply a fault condition in the forward directed zone used for scheme communication
tripping.
Check that the no trip from scheme communication occurs.
Check that the trip time from the forward directed zone used for scheme
communication tripping complies with the zone timer and that correct trip outputs,
Checking of unblocking logic

Check the unblocking function (if the function is required) when you check the
communication scheme.
Command function with continuous unblocking (Unblock = 1).

Procedure
1.
2.
12.11.1.5
Activate the carrier guard input signal (CR_GUARD) of the IED.

Using the scheme selected, check that a carrier accelerated trip (TRIP) is obtained
when the carrier guard signal is deactivated.
Completing the test

purposes.
12.11.2
Current reversal and weak end infeed logic for distance

protection (PSCH, 85)
The current reversal logic and the week end infeed functions are tested during the
secondary injection test of the impedance or overcurrent protection zones together with
the scheme communication logic for the distance protection function (PSCH).
12.11.2.1
Current reversal logic

It is possible to check the delay of the CS carrier send signal with tDelay by changing
from a reverse to a forward fault.
By continuously activating the CR input and changing from a reverse to a forward fault,
the delay tDelay can be checked.
REC 670 ANSI

189
Section 12
Checking of current reversal
The reverse zone timer must not operate before the forward zone fault is
applied. The user might need to block the reverse zone timer during testing
of current reversal.
The forward zone timer must be set longer than 90 ms.
Procedure
1.
2.
3.
4.
5.
12.11.2.2
Activate the carrier receive (CRL) signal.

Set the healthy condition to an impedance at 50% of the reach of the reverse zone
connected to IRVL.
After the pickup condition is obtained for reverse zone, apply a fault at 50% of the
reach of the forward zone connected to WEIBLK1.
Check that correct trip outputs and external signals are obtained for the type of fault
generated.
The operation time should be about the tDelay setting longer than the carrier
accelerated trip (TRIP) previously recorded for permissive scheme communication.
Restore the forward and reverse zone timer to its original setting.
Weak end infeed logic

WEI logic at permissive schemes
Procedure
1.
2.
3.
Check the blocking of the echo with the injection of a CR signal >40 ms after a
reverse fault is applied.
Measure the duration of the echoed signal by applying a CR carrier receive signal.
Check the trip functions and the voltage level for trip by reducing a phase voltage
and applying a CR carrier receive signal.
Testing conditions
Only one type of fault is sufficient, with PSCH function. Apply three faults (one in each
phase), when ZC1P function is used. For phase L1-N fault, set these parameters:
190

REC 670 ANSI
Section 12
Phase
I (Amps)
Phase-angle (Deg) V (Volts)
Phase-angle (Deg)
L1
Set less than UPN<
L2
240
63
240
L3
120
63
120
Change all settings cyclically for other faults (L2-N and L3-N).
Weak end infeed set for trip
Weak end infeed set for echo
1.
2.
3.
4.
5.
6.
7.
8.
12.11.2.3
Apply input signals according table 19.

Activate the carrier receive (CR) signal of the terminal.
After the relay has operated, turn off the input signals.
Check that trip, carrier-send signal, and indication are obtained.
(note: a 200mS pulse)
Apply input signals according table 19.
Activate the carrier receive (CR) signal of the terminal.
After the relay has operated turn off the input signals.
Check that the carrier send signal is obtained.
Completing the test

purposes.
12.11.3
Local acceleration logic (PLAL)

The logic is checked during the secondary injection test of the impedance measuring
zones.
12.11.3.1

Procedure
REC 670 ANSI

191
Section 12
1.
2.
3.
4.
5.
6.
7.
8.
12.11.3.2
Provide the terminal with conditions equivalent to normal load for at least two
seconds.
Deactivate the conditions for accelerated function.
Apply a phase to ground fault at 100% of line impedance.
Check that the fault is tripped with the second zone time delay.
Provide the terminal with conditions equivalent to normal load for at least two
seconds.
Activate the condition for accelerated function either by the auto-recloser or by the
loss of load.
Apply a phase to ground fault at 100% of line impedance.
Check that the fault is tripped instantaneously.
Completing the test

purposes.
12.11.4
Scheme communication logic for residual overcurrent

protection (PSCH, 85)
Before testing the communication logic for residual overcurrent protection, the four step
residual overcurrent protection (PEFM) has to be tested according to the corresponding
instruction. Once this is done, continue with the instructions below.
If the current reversal and weak-end-infeed logic for ground-fault protection is included,
proceed with the testing according to the corresponding instruction after the testing the
communication logic for residual overcurrent protection. The current reversal and weakend-infeed functions shall be tested together with the permissive scheme.
12.11.4.1
Testing the directional comparison logic function

Blocking scheme
Procedure
192

REC 670 ANSI
Section 12
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Inject the polarizing voltage 3V0 at 5% ofVBase(directional TGF)and the with the
current lagging the voltage by 65.
Inject current (65 lagging the voltage) in one phase at about 110% of the set
operating current, and switch the current off with the switch.
Switch the fault current on and measure the operating time of the EFC logic.
Compare the measured time with the set value tCoord.
Activate the CR binary input.
Check that the CRL output is activated when the CR input is activated.
Switch the fault current on (110% of the setting) and wait longer than the set value
tCoord.
Reset the CR binary input.
Activate the BLOCK digital input.
Switch the fault current on (110% of the setting) and wait for a period longer than
the set value tCoord.
Switch the fault current and the polarizing voltage off.
Reset the BLOCK digital input.
Permissive scheme
Procedure
1.
Inject the polarizing voltage 3V0 which is 5% of UBaseVBase (Four step PEFM)
and with the current lagging the voltage by 65.
2. Inject current (65 lagging the voltage) into one phase at about 110% of the set
operating current, and switch the current off with the switch.
3. Switch the fault current on, (110% of the setting) and wait longer than the set value
tCoord.
No TRIP signal should appear, and the CS binary output should be activated.
4. Switch the fault current off.
5. Activate the CR binary input.
6. Switch the fault current on (110% of the setting) and measure the operating time of
the EFC logic.
7. Compare the measured time with the setting for tCoord.
8. Activate the BLOCK digital input.
9. Switch the fault current on (110% of the setting) and wait for a period longer than
the set value tCoord.
10. Switch the fault current and the polarizing voltage off.
11. Reset the CR binary input and the BLOCK digital input.
REC 670 ANSI

193
Section 12
12.11.4.2
Completing the test

purposes.
12.11.5
Current reversal and weak end infeed logic for residual

overcurrent protection (PSCH, 85)
First, test the time delayed residual overcurrent protection according to the corresponding
instruction. Then continue with the instructions below.
Logical signals for current reversal and WEI logic for residual overcurrent protection are
available under menu tree:
Test/Functio status/Current protection/ResidualOverCurrent4Step(PEFM,51N/
67N)/TEFn
12.11.5.1
Testing the current reversal logic

Procedure
1.
2.
3.
4.
5.
6.
12.11.5.2
Inject the polarizing voltage 3V0 to 5% of UBase (directional TGF) and the phase
angle between voltage and current to 155, the current leading the voltage.
Inject current (155 leading the voltage) in one phase to about 110% of the setting
operating current (INDir).
Check that the IRVL output is activated after the set time (tPickUp).
Abruptly reverse the current to 65 lagging the voltage, to operate the forward
directional element.
Check that the IRVL output still is activated after the reversal with a time delay that
complies with the setting (tDelay).
Switch off the polarizing voltage and the current.
Testing the weak-end-infeed logic

If setting parameter WEI=Echo
Procedure
194

REC 670 ANSI
Section 12
1.
2.
3.
4.
5.
6.
7.
8.
9.
Inject the polarizing voltage 3V0 to 5% ofVBase and the phase angle between
voltage and current to 155, the current leading the voltage.
Activate the CRL binary input.
No ECHO and CS should appear.
Switch off the current and check that the ECHO and CS appears on the
corresponding binary output or on the local HMI unit, about 200 ms after resetting
the directional element.
Switch off the CRL binary input.
Switch off the polarizing voltage and reset the BLOCK and CRL binary input.
If setting WEI=Trip
Procedure
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
REC 670 ANSI
Inject the polarizing voltage to about 90% of the setting (3V0) operating voltage.
No ECHO, CS and TRWEI outputs should appear.
Increase the injected voltage to about 110% of the setting (3V0) operating voltage.
Check that the ECHO, CS and TRWEI appears on the corresponding binary output
or on the local HMI.
Reset the CRL binary input.
No ECHO, CS and TRWEI outputs should appear.
Reset the CRL and BLOCK binary input.
Inject the polarizing voltage 3V0 to about 110% of the setting (3V0) and adjust the
phase angle between the voltage and current to 155, the current leading the voltage.
No ECHO, CS and TRWEI should appear.

195
Section 12
No ECHO, CS and TRWEI should appear.

14. Switch the current off and check that the ECHO, CS and TRWEI appears on the
corresponding binary output or on the local HMI, about 200 ms after resetting the
15. Switch the polarizing voltage off and reset the CRL binary input.
12.11.5.3
Completing the test

purposes.
12.12
Logic
12.12.1
Tripping logic (PTRC, 94)

section "Preparing for test" in this chapter. This function is functionality tested together
with other protection functions (line differential protection, ground-fault overcurrent
protection, etc.) within the IED. It is recommended that the function is tested together
with the autoreclosing function, when built into the IED or when a separate external unit
is used for reclosing purposes. The instances of the TRP function are identical except for
the name of the function block (TRPx). The testing is preferable done in conjunction with
the protection system and autoreclosing function.
12.12.1.1
Three phase operating mode

Procedure
1.
2.
196
Make sure that AutoLock and TripLockout are both set to Off.
Initiate a three-phase fault
An adequate time interval between the faults should be considered, to overcome
areset time caused by the possible activation of the autoreclosing function. The
function must issue a three-pole trip in all cases, when trip is initiated by any
protection or some other built-in or external function. The following functional

REC 670 ANSI
Section 12
output signals must always appear simultaneously: TRIP, TR_A, TR_B. TR_Cand
TR3P.
12.12.1.2
1ph/3ph operating mode

In addition to various other tests, the following tests should be performed. They depend
on the complete configuration of an IED:
Procedure
1.
2.
3.
4.
5.
12.12.1.3
Make sure that TripLockout and AutoLock are both set to off.
Initiate different single-phase-to-ground faults one at a time.
Initiate different phase-to-phase and three-phase faults.
Consider using an adequate time interval between faults, to overcome a reset time
which is activated by the autoreclosing function. A three-pole trip should occur for
each separate fault and all of the trips. Functional outputs TRIP, all TR_A, TR_B,
TR_C and TR3P should be active at each fault. No other outputs should be active.
Initiate a single-phase-to-ground fault and switch it off immediately when the trip
signal is issued for the corresponding phase. Initiate the same fault once again within
the reset time of the used autoreclosing function.
signal is issued for the corresponding phase. Initiate the second single-phase-toground fault in one of the remaining phases within the time interval, shorter than
tEvolvingFault (default setting 2.0 s) and shorter than the dead-time of the autoreclosing function, when included in the protection scheme.
Check that the second trip is a three-pole trip and that a three phase autoreclosing
attempt is given after the three phase dead time. Functional outputs TRIP, TR_A,
TR_B, TR_C and TR1P should be active during first fault. No other outputs should
be active. Functional outputs TRIP, all TR_A, TR_B, TR_C and TR3P should be
active during second fault.
1ph/2ph/3ph operating mode

In addition to other tests, the following tests, which depend on the complete configuration
of a IED should be carried out:
Procedure
1.
2.
REC 670 ANSI
Make sure that AutoLock and TripLockout both are set to off.
Initiate different single-phase-to-ground faults one at a time.
Take into consideration an adequate time interval between faults, to overcome a
reset time which is activated by the autoreclosing function. Only a single-pole trip
should occur for each separate fault and only one of the trip outputs (TR01-TR_A,

197
Section 12
3.
4.
5.
6.
7.
12.12.1.4
TR_B, TR_C) should be activated at a time. Functional outputs TR01-TRIP and

TR01-TR1P should be active at each fault. No other outputs should be active.
Initiate different phase-to-phase faults one at a time.
Take into consideration an adequate time interval between faults, to overcome a
reset time which is activated by the autoreclosing function. Only a two-phase trip
should occur for each separate fault and only corresponding two trip outputs (TR_A,
TR_B, TR_C) should be activated at a time. Functional outputs TRIP and TR2P
should be active at each fault. No other outputs should be active.
signal is issued for the corresponding phase. Initiate the same fault once again within
the reset time of the used autoreclosing function.
A single-phase fault shall be given at the first fault. A three-pole trip must be initiated
for the second fault. Check that the corresponding trip signals appear after both
faults. Functional outputs TRIP, TR_A, TR_B, TR_C and TR1P should be active
during first fault. No other outputs should be active. Functional outputs TRIP, all
TR_A, TR_B, TR_C and TR3P should be active during second fault.
signal is generated for the corresponding phase. Initiate the second single-phase-toground fault in one of the remaining phases within the time interval, shorter than
tEvolvingFault (default setting 2.0 s) and shorter than the dead-time of the autoreclosing function, when included in the protection scheme.
Check, that the output signals, issued for the first fault, correspond to a two-phase
trip for included phases. The output signals generated by the second fault must
correspond to the three-phase tripping action.
Circuit breaker lockout

The following tests should be carried out when the built-in lockout function is used in
addition to possible other tests, which depends on the complete configuration of a IED.
Procedure
1.
2.
3.
4.
5.
6.
7.
198
Make sure that AutoLock and TripLockout are both set to Off.
Activate shortly the set lockout (SETLOCKOUT) signal in the IED.
Check that the circuit breaker lockout (CLLKOUT) signal is set.
Activate shortly thereafter, the reset lockout (RSTLKOUT) signal in the IED.
Check that the circuit breaker lockout (CLLKOUT) signal is reset.
A three- trip should occur and all trip outputs ) should be activated. Functional
outputs TRIP and TR3P should be active at each fault. The output CLLKOUT
should not be set.
Activate the automatic lockout function, set AutoLock = On and repeat
Beside the trip outputs, CLLKOUT should be set.

REC 670 ANSI
Section 12
8.
Reset the lockout signal by shortly thereafter activating the reset lockout
(RSTLKOUT) signal.
9. Activate the trip signal lockout function, set TripLockout = On and repeat
All trip outputs (TR_A, TR_B, TR_C) and functional outputs TRIP and TR3P
should be active and stay active after each fault, CLLKOUT should be set.
10. Repeat
All functional outputs should reset.
11. Deactivate the trip signal lockout function, set TripLockout = Off and the automatic
lockout function, set AutoLock = Off.
12.12.1.5
Completing the test

purposes.
12.13
Monitoring
12.13.1
Event counter (GGIO)

The function can be tested by connecting a binary input to the counter under test and from
outside apply pulses to the counter. The speed of pulses must not exceed 10 per second.
Normally the counter will be tested in connection with tests on the function that the
counter is connected to, such as trip logic. When configured, test it together with the
function which operates it. Trig the function and check that the counter result is the same
the number of operations.
12.13.2
Event function (EV)

During testing, the IED can be set when in test mode from the PST. The functionality of
the event reporting during test mode is set from the PST as follows:
Use event masks

Report no events
Report all events
In Test Mode, individual event blocks can be blocked from the PCM 600.
Individually event blocks can also be blocked from the local HMI under the menu:
REC 670 ANSI

199
Section 12
Test/Function test modes/Logic(GGIO)
12.13.3
Fault locator (RFLO)

The fault locator function depends on other functions to work properly, i.e. phase selection
information from distance protection function and analog information supplied by the
trip value recorder function. Check that proper binary initiate(pickup or tripping) and
phase selection signals are connected and voltage and current signals are configured
(parameter settings)
The result is displayed on the local HMI or via PCM 600. Distances to faults for the last
100 recorded disturbances can be found in the local HMI under the menu:
Disturbance Records/Disturbance #n(n = 1100)/General Information
If PCM 600 is used the result is displayed on the recording list after upload, including
loop selection information.
Table 20:
Test settings
Parameter:
Condition:
I
Healthy conditions
V = 69.3 V, I = 0 A & ZF = 0
Impedance |Z|
Test point
Note:
Impedance angle ZF
Test angle
12.13.3.1
Zx (X0 + 2 X1)/3 For single-phase faults

Zx X1 For three and two phase faults
Zx (X0 + 2 X1 XM)/3 For single-phase fault with mutual zerosequence current
ZF arctan[(X0 + 2 X1) / (R0 + 2R1)] For single-phase faults

ZF arctan(X1/R1) For two-phase faults
Measuring the operate limit

Procedure
200

REC 670 ANSI
Section 12
1.
2.
3.
Set the test point (|Z| fault impedance and ZF impedance phase angle ) for a
condition that meets the requirements in table 20.
Subject the IED to healthy normal load conditions for at least two seconds.
Apply a fault condition.
Check that the distance-to-fault value displayed on the HMI complies with the
following equations (the error should be less than five percent):
Z
p = ------x- 100
X1
(Equation 35)
in % for two- and three-pole faults
p=
3 Zx
X0 + 2 X1
100
(Equation 36)
in % for single-phase-to-ground faults

3 Zx
p = --------------------------------------------- 100
X0 + 2 X1 XM
(Equation 37)
in % for single-phase-to-earth faults with mutual zero sequence current.

Where:
12.13.3.2
= the expected value of a distance to fault in percent
Zx
= set test point on the test set
X0
= set zero-sequence reactance of a line
X1
= set positive-sequence reactance of a line
XM
= set mutual zero-sequence impedance of a line
Completing the test

Restore connections and settings to the original values, if they were changed for testing
purpose.
REC 670 ANSI

201
Section 12
12.14
Metering
12.14.1
Pulse counter logic (GGIO)

The test of the pulse counter function requires the Parameter Setting Tool in the PCM or
an appropriate connection to a local HMI with the necessary functionality. A known
number of pulses with different frequencies are connected to the pulse counter input. The
test should be performed with settings Operation = Off/On and the function blocked/
deblocked. The pulse counter value is then recorded by the PCM or local HMI.
12.15
Station communication
12.15.1
Multiple command and trasmit (CM, MT)

This function is only applicable for horizontal communication.
Test of the multiple command function block and multiple trasmit is recommended to be
performed in a system, that is, either in a complete delivery system as an acceptance test
(FAT/SAT) or as parts of that system, because the command function blocks are
connected in a delivery-specific way between bays and the station level and transmit.
Command and trasmit function blocks included in the operation of different built-in
functions must be tested at the same time as their corresponding functions.
12.15.2
Single command (CD)

For the single command function block, it is necessary to configure the output signal to
corresponding binary output of the terminal. The operation of the function is then checked
from the local HMI by applying the commands with the MODE Off, Steady, or Pulse and
by observing the logic statuses of the corresponding binary output. Command control
functions included in the operation of different built-in functions must be tested at the
same time as their corresponding functions.
12.16
Remote communication
12.16.1
Binary signal transfer to remote end

202

REC 670 ANSI
Section 12
To perform a test of the binary signal transfer to remote end the hardware (LDCM) and
binary input and output signals to transfer must be configured as required by the
application.
There are two types of internal self-supervision of the binary signal transfer to remote
end:
The I/O-circuit board is supervised as an I/O module. For example it generates

FAIL if the board is not inserted. I/O-modules not configured are not supervised.
The communication is supervised and the signal COMFAIL is generated if a
communication error is detected.
Status for inputs and outputs as well as self-supervision status are available from the local
HMI under the menus:
Self-supervision status: Diagnostics/Internal events

Status for inputs and outputs: Test/Function status/Function group/Function
Remote communication related signals: Test/Function status/Communication/
Remote communication
Test correct functionality by simulating different kind of faults. Also check that sent and
received data is correctly transmitted and read.
A test connection is shown in figure 70. A binary input signal (BI) at End1 is configured
to be transferred through the communication link to End2. At End2 the received signal
is configured to control a binary output (BO). Check at End2 that the BI signal is received
and the BO operates.
Repeat the test for all the signals configured to be transmitted over the communication
link.
REC 670 ANSI

203
Section 12
Figure 70:
204
Test of RTC with I/O.

REC 670 ANSI
Section 13
Primary injection testing
Section 13 Primary injection testing

About this chapter
This chapter describes tests with primary current through the protected zone to determine
that connections and settings are correct.
13.1

Whenever it becomes necessary to work on primary equipment, it is
essential that all the necessary switching, locking, grounding and safety
procedures are observed and obeyed in a rigid and formalized manner.
Operating and testing procedures should be strictly followed in order to
avoid exposure to the substation equipment that has not been properly deenergized.
A test with primary current through the protected zone is usually a final check that the
current circuits are correctly connected to the IED protection scheme. It is important to
have an appropriate source, which is able to inject sufficient current in the primary circuit
in order to distinguish between noise and real injected current. Therefore it is
recommended that the injection current should be at least 10% of rated CT primary
current.
13.1.1
Voltage control (VCTR)
13.1.1.1
Load drop compensation function, LDC

This function can be tested directly with operational currents i.e. with the power
transformer in service and loaded.
When the system is carrying load there will be a difference between the busbar voltage
(VB) and the voltage at the load point (VL). This difference is load dependent and can
be compensated by the VCTR function.
REC 670 ANSI

205
Section 13
The load current is fed into the VCTR function where parameters corresponding to the
line data for resistance and inductance are set. The voltage drop calculated by the LDC
will be proportional to the voltage drop in the system up to the load point.
In the IED this voltage will be subtracted from the measured busbar voltage (VB) and
the result, corresponding to the voltage at the load point (UL) will be presented to the
VCTR function for the purposes of voltage regulation. This voltage will be lower (if
resitive or inductive load current is applied) than the Vset voltage and VCTR will increase
the voltage in order to achieve the correct system voltage at the load point.
Procedure
1.
2.
3.
4.
5.
6.
13.1.1.2
Confirm that the LDC function is set to On.

Setting Group N1/Control/TransformerVoltageControl/VCP1/LDC/
Operation
Set (or confirm settings for) the line data (RL + j XL) to the load point.
Setting Group N1/Control/TransformerVoltageControl/VCP1/LDC/RLine &
XLine
Check the position of the tap changer.
Read the bus and load voltage from the built in HMI under Main/Control/
Commands/TransformerVoltageControl. Note the values and the difference.
The voltage at the busbar will be the system voltage corresponding to Vset. At load
point it will be lower than the system voltage.
Set R and XL for the LDC to 0 (Zero).
Check the bus and load voltage in the HMI and confirm that both are higher than
the first readings. At load point it will be the system voltage and at the busbar the
system voltage increased with the line voltage drop. The VCTR shall have also
operated during these setting changes.
Testing the LDC function

Procedure
1.
2.
3.
206
Confirm the PST settings for Vset and Vdeadband

Set Rline and Xline for the LDC to 0 (Zero).
Manually operate the tap changer so that the voltage at the transformer (UB)
corresponds to the regulating value Vset.
Neither the "Raise" nor the "Lower" command shall be operating. This can be
confirmed by checking the signals from the configured binary outputs and the Event
Report on the built in HMI. The test of the LDC should be carried out with a single
current at one time from the main current transformers in L1 and L3 phase.
a) When measuring the current from the L1 phase the main CT in L3 phase must
have its secondary winding short circuited and the cables to the RET terminal
disconnected.

REC 670 ANSI
Section 13
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
REC 670 ANSI
b) When measuring the current from the L3 phase the main current transformer in
L1 phase must have its secondary winding short-circuited and the cables to the
terminal disconnected
Modify the connections according to a) above.
Increase slightly the setting Uset so that the RAISE output is on the verge of
activation (ie just below the measured value for bus voltage).
Set Rline and Xline to values for the maximum line impedance to the load point.
The RAISE output should activate when either Rline or Xline will be set to the
maximum value. The operation can be checked at the corresponding binary output
and in the Event Report. If the RAISE output does not activate reset both Rline and
Xline to Zero and set Uset to a little lower value until the Lower circuit is on the
verge of operation.
If the LOWER output activates when either Rline or Xline have a high setting the
current circuits of the L1 phase are incorrect and must be reversed. Incorrect current
polarity may be an issue with physical wiring or the current direction convention
selected for the CT analogue input as part of the PST setting. The operation can be
checked at the corresponding binary output and in the Event Report.
Restore the original connections at the CT in phase L1.
Modify the connections according to b).
Increase slightly the setting Uset so that the RAISE output is on the verge of
activation (ie just below the measured value for bus voltage (UB)).
Set Rline and Xline to values for the maximum line impedance to the load point.
The RAISE output should activate when either Rline or Xline will be set to the
maximum value. The operation can be checked at the corresponding binary output
and in the Event Report. If the RAISE output does not activate reset both Rline and
Xline to Zero and set Uset to a little lower value until the Lower circuit is on the
verge of operation.
If the LOWER output activates when either Rline or Xline have a high setting the
current circuits of the L1 phase are incorrect and must be reversed. Incorrect current
polarity may be an issue with physical wiring or the current direction convention
selected for the CT analogue input as part of the PST setting. The operation can be
checked at the corresponding binary output and in the Event Report.
Retain the settings for Rline and Xline to values as the maximum line impedance
to the load point.
Decrease slowly the setting of Vset until the "Lower" circuit is on the verge of
Operation (ie just above the calculated value for load (VL)).
Reduce the setting for XLine to zero so that the "Lower" circuit operates.
If the operation of Raise and Lower is inverted (Lower instead of Raise and Raise
instead Lower) the current connections have to be reversed in the same way as for
the tests of the Raise component of the voltage regulation with LDC.
Modify the CT connections according to (b) and undertake the same test for the
Lower of the tap changer with LDC (repeating steps 11 to 13).

207
Section 13
15. Restore settings for Vset, RLine and XLine to normal in service values.
16. Restore the original connections at the CT in phase L3.
17. After these tests the single mode voltage control function in the IED can be taken
in to service.
13.1.1.3
Voltage control of Parallel Transformers

Parallel transformer voltage control can be achieved through two methods, Minimum
Circulating Current (MCC refer to section "Minimum Circulating Current (MCC)
method") and Master Follower (MF refer to section "Master Follower (MF)
method").
Parallel transformer control can be achieved via:
a single IED with CAP531 configuration for the necessary data transfer, for up to
four transformers; or
multiple IEDs (with up to 8 VCTR functions in total) communicating via Goose
messages on station bus IEC61850-8-1
The parallel control functions can be tested directly with operational currents i.e. with
the power transformer in service and loaded.
13.1.1.4
Minimum Circulating Current (MCC) method

The method is used when two or more transformers are to be parallel controlled. A
maximum of four transformers can be controlled simultaneously.
To use this method, each transformer protection terminal must be connected to the station
communication bus, in order to exchange data. The following test procedure will assume
the necessary PST and SMT preconfiguration has occurred to enable data exchange
between terminals or between instances of voltage control in the same terminals.
Procedure
1.
2.
3.
4.
5.
208
Confirm or set Uset and Udeadband to the correct in service values.

Set the Overcurrent blocking level (Iblock) to the correct in service value.
Set the Circulating current blocking (OperCCBlock) to On, and the settings for
circulating current limit (CircCurLimit) and time delay for circulating current
blocking (tCircCurr) to the correct in service value.
Set Rline and Xline to 0.
Setting Group N1/Control/Transformer Voltage Control/VCPn/ParCtrl

REC 670 ANSI
Section 13
defined by setting TnRXOP to On or Off. The following rules are applicable on the
function inputs T1RXOP - T4RXOP. If terminal T1 and T2 are connected, T1RXOP
shall be set to On in ATC2 and T2RXOP shall be set to On in ATC1. If T1 - T3 are
available T1RXOP and T2RXOP shall be set to On in ATC3, T2RXOP and
T3RXOP to On in ATC1 and so on.
terminal T2 etc.
6.
7.
8.
9.
10.
11.
12.
13.
Set the parallel operation (OperationPAR) to Off.

On the IED built in HMI, set the control mode to Manual for each transformer in
the parallel control group.
Undertaking switching operations to connect all transformers to the same bus on
the secondary side.
Manually execute Raise commands from the IED built in HMI to step up the tap
changer for transformer T1, two steps above the setting for the other transformers
in the parallel group.
Change the setting of Uset in each of the remaining transformers to correspond to
the manually set busbar voltage being measured by T1, which can be located on the
IED HMI under
Main/Control/Command/TransformerVoltageControl/Bus Voltage.
Set in all the parallel connected transformers the parameter OperationPAR to CC.
On the IED built in HMI, set the control mode to Automatic for all transformers.
For transformer T1 adjust the parameter Comp Setting Group N1/Control/
Transformer Voltage Control/VCP1/ParCtrl/Comp so that the LOWER output
is activated due to circulating current, based on guidelines below.
Comp is a setting for circulating current Compensating Factor, and
it is effectively a multiplier value to change the sensitivity of the
voltage regulation function to measured values of circulating
current. A nominal value of 200 for Comp should be appropriate to
achieve sensitive voltage regulation. Values less may lead to a
normal state where tap changers for parallel transformers are well
out of step, and values significantly higher will cause over
sensitivity in the voltage control function and tap changer hunting
behaviour.
It is an important outcome of the testing process that the
compensating factor is checked for each transformer to ensure
sensitive but stable operation for circulating currents.
Example of Comp Behaviour
If there are three transformers connected in parallel, and the tap
changer of transformer T1 lies two steps over the tap changer of T2
and T3, the circulating current detected by the VCTR for T1 will be
REC 670 ANSI

209
Section 13
the sum (with opposite sign) of the current measured at T2 and T3.
The currents measured at T2 and T3 will ideally be about the same
values.
If the voltage is close to the upper limit of the Vdeadband the tap
changer of T1 will try to decrease the controlled voltage, but in the
opposite case, i.e. the voltage is close to the lower limit of
Vdeadband, the tap changer at T1 will not try to decrease the
controlled voltage.
The tap changer for T2 and T3 will not operate due to the fact that
the detected circulating current will be half of the current detected
at T1.
The setting of the parameter Comp then might need to be increased
a little.
At least one Tap Changer step difference between the different
transformers should be allowed in order to avoid the Tap Changers
to operate too often. If the allowed difference is for example two
steps, the Tap Changer shall be stepped up three steps when setting
parameter Comp. This applies to all the VCTR in the same group.
14. The setting of the parameter Comp at T2 and T3 will be carried out in the same
manner as at T1. According to the described procedure when the Tap Changer of
one transformer lies two steps above the others, it shall automatically step down.
When there are only two transformers in the group either shall one step down or the
other step up depending on the voltage level at the VCTR.
15. Before placing the VCTR into service, confirm the correct settings of Uset,
Udeadband, the blocking settings for overcurrent, undervoltage and high circulating
currents, and the compensating parameters Rline and Xline.
Also confirm SMT settings for binary Raise and Lower outputs in conjunction with
the basic CET configuration for Goose messages between parallel transformer
control functions.
16. Ensure that Automatic Control mode is set for each transformer from the IED and
that OperationPAR is set to CC.
13.1.1.5
Master Follower (MF) method

Master follower method requires a Master to be nominated in a parallel group, that is
responsible for measuring secondary bus voltage, and executing commands to raise and
lower tap changers, that are repeated by Follower transformers in the group.
Procedure
1.
2.
3.
210
Confirm or set Vset and Vdeadband to the correct in service values.

Set the Overcurrent blocking level (IBlock) to the correct in service value.
Set Rline and Xline to 0.

REC 670 ANSI
Section 13
4.
5.
Confirm the setting of MFMode as Follow Tap or Follow Cmd. If this setting is
Follow Tap, all Follower transformers shall match the actual tap setting of the
Master, while Follow Cmd requires that Follower transformers follow the Raise and
Lower commands executed by the Master.
General Settings/Control/TransformerVoltageControl/VCP1/MFMode
Note that the maximum difference in tap positions for parallel transformers will be
determined by PST setting[Setting Group N1/Control/
TransformerVoltageControl/VCP1/MFPosDiffLim and that tap differences
exceeding that setting can produce system alarms or blocking of the VCTR.
Setting Group N1/Control/Transformer Voltage Control/VCP1/ParCtrl
defined by setting TnRXOP to On or Off. The following rules are applicable on the
function inputs T1RXOP - T4RXOP. If terminal T1 and T2 are connected, T1RXOP
shall be set to On in ATC2 and T2RXOP shall be set to On in ATC1. If T1 - T3 are
available T1RXOP and T2RXOP shall be set to On in ATC3, T2RXOP and
T3RXOP to On in ATC1 and so on.
terminal T2 etc.
6.
7.
8.
9.
10.
11.
12.
13.
14.
REC 670 ANSI
Set the parallel operation (OperationPAR) to Off for each transformer.

On the IED built in HMI, set the control mode to Manual for each transformer in
the parallel control group.
Undertaking switching operations to connect all transformers to the same bus on
the secondary side.
Set OperationPAR to MF for all transformers in the parallel group and confirm that
the lowest transformer number in the group is set as Master. Allow the issue of raise
and lower commands so that the secondary bus voltage stabilises at Vset.
Change Vset in the Master transformer T1 so that it is 1% below the measured bus
voltage value on the IED built in HMI and set all transformers to Automatic control
mode using the IED built in HMI
The Master in the parallel group will issue a Lower command after time delay t1,
which will also be repeated by the Follower transformers in the group.
Return Vset for T1 to its normal in service value.
Using the IED built in HMI, set Transformer 2 to Master of the parallel group and
T1 to Follower (in that order) and repeat steps 9-11. Undertake this same test by
setting each Transformer in turn to Master.
Note that voltage regulation will be mutually blocked if no transformer is set to
Master in the parallel group. To confirm this function, Set T1 as Master in the
parallel group and allow automatic voltage regulation to occur such that the
measured bus voltage is stable around Vset. Without allocating a new Master, set

211
Section 13
T1 to Follower and note the Automatic block state on the IED built in HMI for all
parallel transformers.
15. Restore T1 to Master of the parallel transformer group and ensure that control mode
for each transformer is Automatic, OperationPAR is set to MF and settings for
Vset are restored to normal in service values.
13.1.1.6
Completing the test

purposes.
212

REC 670 ANSI
Section 14
Commissioning and maintenance of the fault clearing system
Section 14 Commissioning and maintenance of

the fault clearing system
About this chapter
This chapter discusses maintenance tests and other periodic maintenance measures.
14.1
Installation and commissioning

The protection relay system is in an "on-guard" situation where they can be inactive for
several years and then suddenly be required to operate within fractions of a second. This
means that maintenance testing with certain time intervals should be performed to detect
failures of the protection IED or the surrounding circuits. This is a complement to the
advanced self supervision in the modern protection IED.
Relays are not expected to deteriorate with usage but extreme conditions such as
mechanical shocks, AC or DC transients, high ambient temperatures, and high air
humidity always have a certain likelihood of causing damages.
Delivered equipment undergoes extensive testing and quality control in the ABB
manufacturing program. All types of IEDs and their integral components have been
subject to extensive laboratory testing during the development and design work. Prior to
series production of a specific IED, it is Type tested according to national and
international standards. Each individual relay in normal production is individually tested
and calibrated before delivery.
Protection relays installed in an apparatus cubicle shall be checked in various ways before
delivery. Insulation test (to check for bad wiring) and complete testing of all equipment
with injection of currents and voltages is performed.
During the design of the station certain steps shall be taken to limit the risk of failures
e.g. all relay coils are connected to negative potential to ground to prevent contact
corrosion due to electrolyte.
Certain circuits are continuously supervised to improve their availability. Examples of
such supervisions are:
REC 670 ANSI

213
Section 14
Trip circuit supervision

Protection DC supply supervision
DC system ground fault supervision
Busbar protection CT-circuit supervision
Protection relays shall be encapsulated according to environment requirements. In

tropical climates, cubicles are provided with glass-door and ventilation louvres. Heaters
for anti-condensation, often thermostatically controlled are provided. Cubicle power-loss
is limited not to exceed protection IED temperature limits which is 55C.
14.2
Commissioning tests
During commissioning all protection functions shall be verified with the setting values
used at each plant. The commissioning tests must include verification of all circuits by
highlighting the circuit diagrams and the configuration diagrams for the used functions.
Further, the settings for protection functions are tested and recorded carefully as outlined
for the future periodic maintenance tests described below.
The final testing will include primary verification of all directional functions where load
currents is checked on the IED through the LHMI or the PCM 600 tool. The
magnitudes and angles of all currents and voltages should be checked and the symmetry
verified.
Directional functions have information about the measured direction and for example
measured impedance. These values must be checked and verified as correct with the
export or import of power available.
Finally final trip tests must be performed. This involves activation of protection functions
or tripping outputs with the circuit breaker closed and the tripping of the breaker verified.
When several breakers are involved each must be checked individually and it must be
verified that the other involved breakers are not tripped at the same time.
14.3
Periodic maintenance tests

The periodicity of all tests depends on several factors, for example the importance of the
installation, environment conditions, simple or complex equipment, static or
electromechanical relays etc.
The normal maintenance practices of the user should be followed. However ABB
proposal is to test:
214

REC 670 ANSI
Section 14
Every second to third year:
Visual inspection of all equipment.

Removal of dust on ventilation louvres and relays if necessary.
Periodic maintenance test for protection relays of object where no redundant
protections are provided.
Every four to six years:
Periodic maintenance test for protection relays of objects with redundant protection
system.
First maintenance test should always be carried out after the first half year
of service.
When protection IEDs are combined with built-in control the test interval
can be increased drastically, up to for instance 15 years, because the IED
continuously reads service values, operates the breakers etc.
14.3.1
Visual inspection
Prior to testing, the protection IEDs should be inspected in order to detect any visible
damage that may have occurred (dirt or moisture deposits, overheating, etc.). Should
burned contacts be observed when inspecting the relays, a diamond file or an extremely
fine file can be used to polish the contacts. Emery cloth or similar products must not be
used as insulating grains of abrasive may be deposited on the contact surfaces and cause
failure.
Make sure that all IEDs are equipped with covers.
14.3.2
Maintenance tests
To be made after the first half year of service, then with the cycle as proposed above and
after any suspected maloperation or change of the relay setting.
Testing of protection relays shall preferably be made with the primary circuit deenergized. The relay cannot protect the circuit during testing. Trained personnel may test
one relay at a time on live circuits where redundant protection is installed and deenergization of the primary circuit is not allowed.
REC 670 ANSI

215
Section 14
ABB protection relays are preferably tested by aid of components from the COMBITEST
testing system or FT test systems described in information B03-9510 E. Main components
are RTXP 8/18/24 test switch located to the left in each protection relay and RTXH
8/18/24 test handle which is inserted in test switch at secondary testing. All necessary
operations such as opening of trip circuits, short-circuiting of current circuits and opening
of voltage circuits are automatically performed in the right order to allow for simple and
safe secondary testing even with the object in service.
Important components of FT test system are FT1, FTx, FT19, FT19RS, FR19RX switches
and assemblies as well as FT-1 test plug.
14.3.2.1
Preparation
Before starting maintenance testing the test engineers should scrutinize applicable circuit
diagrams and have the following documentation available: Test instructions for protection
IEDs to be tested. Test records from previous commissioning and maintenance tests. List
of valid settings. Blank test records to fill in measured values.
14.3.2.2
Recording
It is of utmost importance to carefully record the test results. Special test sheets covering
the frequency of test, date of test and achieved test values should be used. Relay setting
list and protocols from previous tests should be available and all results should be
compared for differences. At component failures, spare equipment is used and set to the
requested value. A note of the exchange is made and the new measured values are
recorded. Test records for several years of testing should be stored in a common file for
a station, or a part of a station, to give a simple overview of the period of testing and
achieved test values. These test records are valuable when analysis of service disturbances
shall be done.
14.3.2.3
Secondary injection
The periodic maintenance test is done by secondary injection from a portable test set.
Each protection shall be tested according to the secondary injection test information for
the specific protection IED. Only the setting values adopted shall be checked for each
protection function. If the discrepancy between obtained value and requested set value is
too big the setting should be adjusted, the new value recorded and a note should be made
in the test record.
14.3.2.4
Alarm test
When inserting the test handle of RTXP or using FT plugs, the alarm and event signalling
is normally blocked. This is done in IED 670 by setting the Event reporting to off during
the test. This can be done when the test handle is inserted or the IED is set to test mode
216

REC 670 ANSI
Section 14
from the LHMI. At the end of the secondary injection test it should be checked that the
event and alarm signalling is correct by activating the events and performing some
selected tests.
14.3.2.5
Self supervision check

Once secondary testing has been completed it should be checked that no self supervision
signals are activated continuously or sporadically. Especially check the time
synchronizsation system, GPS or other, and communication signals, both station
communication(61850/SPA/LON..) and remote communication, for example line the
differential communication system.
14.3.2.6
Trip circuit check

When the protection IED undergoes an operational check, a tripping pulse is normally
obtained on one or more of the output contacts and preferably on the test switch. The
healthy circuit is of utmost importance for the protection operation. If the circuit is not
provided with a continuous trip circuit supervision it is possible to check that circuit is
really closed when the test-plug handle has been removed by using a high-ohmic
voltmeter and measuring between the plus and the trip output on the panel. The
measurement is then done through the tripping magnet of the circuit breaker (note!
Breaker must be closed) and therefore the complete tripping circuit is checked. Please
observe that the test system does not have its built-in security during this test. If the
instrument should be set on Amp instead of Volts, the circuit breaker naturally is tripped,
therefore, greatest care is necessary.
Trip circuit from trip relays to circuit breaker is often supervised by trip circuit supervision
relay. It can then be checked that a circuit is healthy by opening tripping output terminals
in the cubicle. When terminal is opened an alarm shall be achieved on the signal system
after a delay of some seconds. However, remember to close the circuit directly after the
test and tighten the terminal carefully!
14.3.2.7
Measurement of service currents

After a maintenance test it is recommended to measure the service currents and service
voltages recorded by the protection IED. The service values are checked on the IED 670
local HMI or with the PCM 600 tool. Ensure that the correct values and angles between
voltages and currents are recorded. Also check the direction of directional functions such
as Distance and directional overcurrent functions.
For a transformer differential protection the achieved differential current value is
dependent on tap changer position and can vary between less than 1 % up to perhaps 10%
of rated current. For line differential functions the capacitive charging currents can
normally be recorded as a differential current.
REC 670 ANSI

217
Section 14
The zero-sequence current to ground-fault protection relays should be measured. The

current amounts normally very small but it is normally possible to see if the current circuit
is "alive".
The neutral-point voltage to an ground-fault relay is checked. The voltage is normally
0.1 to 1V secondary. However, voltage can be considerably higher due to harmonics
normally a CVT secondary can have around 2.5-3% third harmonic voltage.
14.3.2.8
Restoring
Maintenance is very important to improve the availability of the protection system by
detecting failures before the protection is required to operate. There is however little point
in testing healthy equipment and then putting it back into service with an open terminal,
with a removed fuse or open miniature circuit breaker with an open connection, wrong
setting etc.
Thus a list should be prepared of all items disturbed during test so that all can be put back
into service quickly and without overlooking something. It should be put back into service
item by item and signed by the responsible engineer.
218

REC 670 ANSI
Section 15
Fault tracing and repair
Section 15 Fault tracing and repair

About this chapter
This chapter describes how to carry out fault tracing and if necessary, a change of circuit
board.
15.1
Fault tracing
15.1.1
Information on the local HMI

If an internal fault has occurred, the local HMI displays information under:
Diagnostics/IED status/General
Under the Diagnostics menus, indications of a possible internal failure (serious fault) or
internal warning (minor problem) are listed.
Indications regarding the faulty unit are outlined in table 21.
Table 21:
HMI Signal Name:
Self-supervision signals in the built-in HMI

Status
Description
INT Fail
OFF / ON
This signal will be active if one or more of

the following internal signals are active;
INT--NUMFAIL, INT--LMDERROR, INT-WATCHDOG, INT--APPERROR, INT-RTEERROR, INT--FTFERROR, or any of
the HW dependent signals
INT Warning
OFF / ON

INT--RTCERROR, INT-IEC61850ERROR, INT-TIMESYNCHERROR
NUM Fail
OFF / ON

INT--WATCHDOG, INT--APPERROR,
INT--RTEERROR, INT--FTFERROR
NUM Warning
OFF / ON

INT--RTCERROR, INT-IEC61850ERROR
REC 670 ANSI

219
Section 15
HMI Signal Name:
Status
Description
ADMnn
READY / FAIL
Analog input module n failed. Signal

activation will reset the IED
BIMnn
READY / FAIL
BIM error. Binary input module Error

status. Signal activation will reset the IED
BOMn
READY / FAIL
BOM error. Binary output module Error

status.
IOMn
READY / FAIL
IOM-error. Input/Output Module Error

status.
MIMn
READY / FAIL
mA input module MIM1 failed. Signal

activation will reset the IED
RTC
READY / FAIL
This signal will be active when there is a

hardware error with the real time clock.
Time Sync
READY / FAIL
This signal will be active when the source

of the time synchronization is lost, or when
the time system has to make a time reset.
Application
READY / FAIL

the application threads are not in the state
that Runtime Engine expects. The states
can be CREATED, INITIALIZED,
RUNNING, etc.
RTE
READY / FAIL
This signal will be active if the Runtime

Engine failed to do some actions with the
application threads. The actions can be
loading of settings or parameters for
components, changing of setting groups,
loading or unloading of application
threads.
IEC61850
READY / FAIL
This signal will be active if the IEC61850

stack did not succeed in some actions like
reading IEC61850 configuration, startup
etc.
LMD
READY / FAIL
LON network interface, MIP/DPS, is in an

unrecoverable error state.
LDCMxxx
READY / FAIL
Line Differential Communication Error

status
OEM
READY / FAIL
Optical Ethernet Module error status.
Also the internal signals, such as INT--FAIL and INT--WARNING can be connected to
binary output contacts for signalling to a control room.
In the IED Status - Information, the present information from the self-supervision function
can be viewed. Indications of failure or warnings for each hardware module are provided,
as well as information about the external time synchronization and the internal clock. All
according to table 21. Loss of time synchronization can be considered as a warning only.
The IED 670 has full functionality without time synchronization.
220

REC 670 ANSI
Section 15
15.1.2
Using front-connected PC or SMS

Here two summary signals appear, self-supervision summary and numerical module
status summary. These signals can be compared to the internal signals as:
Self-supervision summary = INT--FAIL and INT--WARNING

CPU-module status summary = INT--NUMFAIL and INT--NUMWARN
When an internal fault has occurred, you can retrieve extensive information about the
fault from the list of internal events available in the SMS part:
TRM-STAT TermStatus - Internal Events
The list of internal events provides valuable information, which can be used during
commissioning and during fault tracing.
The internal events are time tagged with a resolution of 1 ms and stored in a list. The list
can store up to 40 events. The list is based on the FIFO principle, when it is full, the oldest
event is overwritten. The list cannot be cleared; its content cannot be erased.
The internal events in this list not only refer to faults in the IED, but also to other activities,
such as change of settings, clearing of disturbance reports, and loss of external time
synchronization.
The information can only be retrieved with the aid of the PST software package. The PC
can be connected either to the port at the front or at the rear of the IED.
These events are logged as internal events.
Table 22:
Events available for the internal event list in the IED
Event message:
INT--FAIL
Description
Off
Internal fail status
INT--FAIL
INT--WARNING
Off
Internal warning status
Off
Numerical module fatal error

status
INT--NUMFAIL (reset event)

INT--NUMFAIL (set event)
Off
Numerical module non-fatal error

status
INT--NUMWARN
IOn--Error
lNT--WARNING (reset event)

lNT--WARNING (set event)
INT--NUMFAIL
INT--NUMWARN
INT--FAIL (reset event)

INT--FAIL (set event)
INT--WARNING
INT--NUMFAIL
Generating signal:
INT--NUMWARN (reset event)

INT--NUMWARN (set event)
Off
In/Out module No. n status
IOn--Error
IOn--Error (reset event)

IOn--Error (set event)
REC 670 ANSI

221
Section 15
Event message:
Description
ADMn-Error
Off
Analog/Digital module No. n

status
Off
mA-input module status
ADMn-Error
Generating signal:
ADMn-Error (reset event)
ADMn-Error (set event)
MIM1-Error
MIM1-Error
MIM1-Error (reset event)

MIM1-Error (set event)
INT--RTC
Off
Real Time Clock (RTC) status
INT--RTC
INT--RTC (reset event)

INT--RTC (set event)
INT--TSYNC
Off
External time synchronization

status
INT--TSYNC
INT--TSYNC (reset event)

INT--TSYNC (set event)
INT--SETCHGD
Any settings in IED changed
DRPC-CLEARED
All disturbances in Disturbance

report cleared
The events in the internal event list are time tagged with a resolution of 1 ms.
This means that when using the PC for fault tracing, it provides information on the:
15.2
Module that should be changed.

Sequence of faults, if more than one unit is faulty.
Exact time when the fault occurred.
Repair instruction
Never disconnect the secondary connection of a current transformer
circuit without short-circuiting the transformers secondary winding.
Operating a current transformer with the secondary winding open will
cause a massive potential build up that may damage the transformer and
may cause injuries to humans.
Never connect or disconnect a wire and/or a connector to or from a IED

during normal service. Hazardous voltages and currents are present that
may be lethal. Operation may be disrupted and IED and measuring
circuitry may be damaged.
222

REC 670 ANSI
Section 15
An alternative is to open the IED and send only the faulty circuit board to ABB for repair.
When a printed circuit board is sent to ABB, it must always be placed in a metallic, ESDproof, protection bag. The user can also purchase separate replacement modules.
Strictly follow the company and country safety regulations.
Most electronic components are sensitive to electrostatic discharge and latent damage
may occur. Please observe usual procedures for handling electronics and also use an ESD
wrist strap. A semi-conducting layer must be placed on the workbench and connected to
ground.
Disassemble and reassemble the 670 IED accordingly:
1.
2.
3.
4.
5.
6.
Switch off the dc supply.

Short-circuit the current transformers and disconnect all current and voltage
connections from the IED.
Disconnect all signal wires by removing the female connectors.
Disconnect the optical fibers.
Unscrew the main back plate of the IED.
If the transformer module is to be changed:
Remove the IED from the panel if necessary.

Remove the rear plate of the IED.
Remove the front plate.
Remove the TRM screws, both front and rear.
7.
8.
9.
Pull out the faulty module.

Check that the new module has a correct identity number.
Check that the springs on the card rail are connected to the corresponding metallic
area on the circuit board when the new module is inserted.
10. Reassemble the IED.
If the IED 670 has been calibrated with the system inputs, the calibration procedure must
be performed again to maintain the total system accuracy.
15.3
Repair support
If a IED 670 needs to be repaired, the whole IED must be removed and sent to an ABB
Logistic Center. Please get in touch with your local ABB representative to get more
details.
REC 670 ANSI

223
Section 15
15.4
Maintenance
The IED 670 is self-supervised. No special maintenance is required.
Instructions from the power network company and other maintenance directives valid for
maintenance of the power system must be followed.
224

REC 670 ANSI
Section 16
Glossary
Section 16 Glossary
About this chapter
This chapter contains a glossary with terms, acronyms and abbreviations used in ABB
technical documentation.
16.1
REC 670 ANSI
Glossary
AC
Alternating current
A/D converter
Analog to digital converter
ADBS
Amplitude dead -band supervision
ADM
Analog digital conversion module, with time synchronization
ANSI
American National Standards Institute
AR
Autoreclosing
AngNegRes
Setting parameter/ZD/
ArgDirAngDir
Setting parameter/ZD/
ASCT
Auxiliary summation current transformer
ASD
Adaptive signal detection
AWG
American Wire Gauge standard
BBP
Busbar protection
BFP
Breaker failure protection
BIM
Binary input module
BOM
Binary output module
BR
External bi-stable relay
BS
British standard
BSR
Binary signal transfer function, receiver blocks
BST
Binary signal transfer function, transmit blocks
C37.94
IEEE/ANSI protocol used when sending binary signals between

IEDs

225
Section 16
Glossary
226
CAN
Controller Area Network. ISO standard (ISO 11898) for serial

communication
CAP 531
Configuration and programming tool
CB
Circuit breaker
CBM
Combined backplane module
CCITT
Consultative Committee for International Telegraph and

Telephony. A United Nations sponsored standards body within
the International Telecommunications Union.
CCM
CAN carrier module
CCVT
Capacitive Coupled Voltage Transformer
Class C
Protection Current Transformer class as per IEEE/ ANSI
CMPPS
Combined mega pulses per second
CO cycle
Close-open cycle
Co-directional
Way of transmitting G.703 over a balanced line. Involves two

twisted pairs making it possible to transmit information in both
directions
COMTRADE
Standard Common Format for Transient Data Exchange format

for Disturbance recorder according to IEEE/ANSI C37.111,
1999 / IEC60255-24
Contra-directional
Way of transmitting G.703 over a balanced line. Involves four

twisted pairs of with two are used for transmitting data in both
directions, and two pairs for transmitting clock signals
CPU
Central processor unit
CR
Carrier receive
CRC
Cyclic redundancy check
CS
Carrier send
CT
Current transformer
CVT or CCVT
Capacitive voltage transformer
DAR
Delayed auto-reclosing
DARPA
Defense Advanced Research Projects Agency (The US developer

of the TCP/IP protocol etc.)
DBDL
Dead bus dead line
DBLL
Dead bus live line
DC
Direct current
DFT
Discrete Fourier transform

REC 670 ANSI
Section 16
Glossary
REC 670 ANSI
DIP-switch
Small switch mounted on a printed circuit board
DLLB
Dead line live bus
DNP
Distributed Network Protocol as per IEEE/ANSI Std. 1379-2000
DR
Disturbance recorder
DRAM
Dynamic random access memory
DRH
Disturbance report handler
DSP
Digital signal processor
DTT
Direct transfer trip scheme
EHV network
Extra high voltage network
EIA
Electronic Industries Association
EMC
Electro magnetic compatibility
EMF
Electro motive force
EMI
Electro magnetic interference
EnFP
End fault protection
ESD
Electrostatic discharge
FOX 20
Modular 20 channel telecommunication system for speech, data

and protection signals
FOX 512/515
Access multiplexer
FOX 6Plus
Compact, time-division multiplexer for the transmission of up to

seven duplex channels of digital data over optical fibers
G.703
Electrical and functional description for digital lines used by local

telephone companies. Can be transported over balanced and
unbalanced lines
GCM
Communication interface module with carrier of GPS receiver

module
GI
General interrogation command
GIS
Gas insulated switchgear
GOOSE
Generic object oriented substation event
GPS
Global positioning system
GSM
GPS time synchronization module
HDLC protocol
High level data link control, protocol based on the HDLC

standard
HFBR connector
type
Plastic fiber connector

227
Section 16
Glossary
228
HMI
Human machine interface
HSAR
High speed auto reclosing
HV
High voltage
HVDC
High voltage direct current
IDBS
Integrating dead band supervision
IEC
International Electrical Committee
IEC 60044-6
IEC Standard, Instrument transformers Part 6: Requirements

for protective current transformers for transient performance
IEC 60870-5-103
Communication standard for protective equipment. A serial

master/slave protocol for point-to-point communication
IEC 61850
Substation Automation communication standard
IEEE
Institute of Electrical and Electronics Engineers
IEEE 802.12
A network technology standard that provides 100 Mbits/s on

twisted-pair or optical fiber cable
IEEE P1386.1
PCI Mezzanine card (PMC) standard for local bus modules.

References the CMC (IEEE P1386, also known as Common
mezzanine card) standard for the mechanics and the PCI
specifications from the PCI SIG (Special Interest Group) for the
electrical EMF Electro Motive Force.
IED
Intelligent electronic device
I-GIS
Intelligent gas insulated switchgear
IOM
Binary input/output module
Instance
When several occurrences of the same function are available in

the IED they are referred to as instances of that function. One
instance of a function is identical to another of the same kind but
will have a different number in the IED user interfaces. The word
instance is sometimes defined as an item of information that is
representative of a type. In the same way an instance of a function
in the IED is representative of a type of function.
IP
1. Internet protocol. The network layer for the TCP/IP protocol

suite widely used on Ethernet networks. IP is a connectionless,
best-effort packet switching protocol. It provides packet routing,
fragmentation and re-assembly through the data link layer.
2. Ingression protection according to IEC standard
IP 20
Ingression protection, according to IEC standard, level

IP20- Protected against solidforeign objects of12.5mm diameter
andgreater.

REC 670 ANSI
Section 16
Glossary
REC 670 ANSI
IP 40
Ingression protection, according to IEC standard, level IP40Protected against solid foreign objects of 1mm diameter and
greater.
IP 54
Ingression protection, according to IEC standard, level

IP54-Dust-protected,protected againstsplashing water.
IRF
Internal fail signal
IRIG-B:
InterRange Instrumentation Group Time code format B, standard

200
ITU
International Telecommunications Union
LAN
Local area network
LIB 520
High voltage software module
LCD
Liquid crystal display
LDCM
Line differential communication module
LDD
Local detection device
LED
Light emitting diode
LNT
LON network tool
LON
Local operating network
MCB
Miniature circuit breaker
MCM
Mezzanine carrier module
MIM
Milli-ampere module
MPM
Main processing module
MVB
Multifunction vehicle bus. Standardized serial bus originally

developed for use in trains.
NCC
National Control Centre
NUM
Numerical module
OCO cycle
Open-close-open cycle
OCP
Overcurrent protection
OEM
Optical ethernet module
OLTC
On load tap changer
OV
Over voltage
Overreach
A term used to describe how the relay behaves during a fault

condition. For example a distance relay is over-reaching when
the impedance presented to it is smaller than the apparent
impedance to the fault applied to the balance point, i.e. the set

229
Section 16
Glossary
reach. The relay sees the fault but perhaps it should not have
seen it.
PCI
Peripheral component interconnect, a local data bus
PCM
Pulse code modulation
PCM 600
Protection and control IED manager
PC-MIP
Mezzanine card standard
PISA
Process interface for sensors & actuators
PMC
PCI Mezzanine card
POTT
Permissive overreach transfer trip
Process bus
Bus or LAN used at the process level, that is, in near proximity
to the measured and/or controlled components
PSM
Power supply module
PST
Parameter setting tool
PT ratio
Potential transformer or voltage transformer ratio
PUTT
Permissive underreach transfer trip
RASC
Synchrocheck relay, COMBIFLEX
RCA
Relay characteristic angle
REVAL
Evaluation software
RFPP
Resistance for phase-to-phase faults

Resistance for phase-to-ground faults
230
RISC
Reduced instruction set computer
RMS value
Root mean square value
RS422
A balanced serial interface for the transmission of digital data in

point-to-point connections
RS485
Serial link according to EIA standard RS485
RTC
Real time clock
RTU
Remote terminal unit
SA
Substation Automation
SC
Switch or push-button to close
SCS
Station control system
SCT
System configuration tool according to standard IEC 61850
SLM
Serial communication module. Used for SPA/LON/IEC

communication.

REC 670 ANSI
Section 16
Glossary
REC 670 ANSI
SMA connector
Subminiature version A, A threaded connector with constant

impedance.
SMS
Station monitoring system
SNTP
Simple network time protocol is used to synchronize computer

clocks on local area networks. This reduces the requirement to
have accurate hardware clocks in every embedded system in a
network. Each embedded node can instead synchronize with a
remote clock, providing the required accuracy.
SPA
Strmberg protection acquisition, a serial master/slave protocol

for point-to-point communication
SRY
Switch for CB ready condition
ST
Switch or push-button to trip
Starpoint
Neutral/Wye point of transformer or generator
SVC
Static VAr compensation
TC
Trip coil
TCS
Trip circuit supervision
TCP
Transmission control protocol. The most common transport layer

protocol used on Ethernet and the Internet.
TCP/IP
Transmission control protocol over Internet Protocol. The de

facto standard Ethernet protocols incorporated into 4.2BSD Unix.
TCP/IP was developed by DARPA for internet working and
encompasses both network layer and transport layer protocols.
While TCP and IP specify two protocols at specific protocol
layers, TCP/IP is often used to refer to the entire US Department
of Defense protocol suite based upon these, including Telnet,
FTP, UDP and RDP.
TEF
Time delayed gound-fault protection function
TNC connector
Threaded Neill Concelman, A threaded constant impedance

version of a BNC connector
TPZ, TPY, TPX,

TPS
Current transformer class according to IEC
Underreach
A term used to describe how the relay behaves during a fault

condition. For example a distance relay is under-reaching when
the impedance presented to it is greater than the apparent
impedance to the fault applied to the balance point, i.e. the set
reach. The relay does not see the fault but perhaps it should
have seen it. See also Overreach.

231
Section 16
Glossary
U/I-PISA
Process interface components that deliver measured voltage and

current values
UTC
Coordinated universal time. A coordinated time scale, maintained

by the Bureau International des Poids et Mesures (BIPM), which
forms the basis of a coordinated dissemination of standard
frequencies and time signals. UTC is derived from International
Atomic Time (TAI) by the addition of a whole number of "leap
seconds" to synchronize it with Universal Time 1 (UT1), thus
allowing for the eccentricity of the Earth"s orbit, the rotational
axis tilt (23.5 degrees), but still showing the Earth"s irregular
rotation, on which UT1 is based. The Coordinated Universal
Time is expressed using a 24-hour clock and uses the Gregorian
calendar. It is used for aeroplane and ship navigation, where it
also sometimes known by the military name, "Zulu time". "Zulu"
in the phonetic alphabet stands for "Z" which stands for longitude
zero.
UV
Undervoltage
WEI
Weak end infeed logic
VT
Voltage transformer
X.21
A digital signalling interface primarily used for telecom

equipment
3IO
Three times zero-sequence current. Often referred to as the

residual or the -fault current
Three times the zero sequence voltage. Often referred to as the
residual voltage or the neutral point voltage
232

REC 670 ANSI

Installation and Commisioning Manual REC670

Uploaded by

Copyright:

Available Formats

Installation and Commisioning Manual REC670

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Installation and Commisioning Manual REC670

Uploaded by

Copyright:

Available Formats

Installation and commissioning manual

Bay control IED

Document ID: 1MRK511189-UUS

Copyright 2007 ABB. All rights reserved

Unpacking and checking the IED........................................21

Installing the IED.................................................................23

REC 670 ANSI

Installation and commissioning manual

Mounting procedure for wall mounting.........................................34

Checking the external optical and electrical

Installation and commissioning manual

REC 670 ANSI

Checking the VT circuits.........................................................................75

Energizing the IED..............................................................79

Set up PCM 600 communication link per IED.....................85

Establishing connection and verifying the SPA/IECcommunication ...................................................................91

Section 10 Establishing connection and verifying the LON

Section 11 Configuring the IED and changing settings.......................103

REC 670 ANSI

Installation and commissioning manual

Entering settings through the local HMI................................................104

Section 12 Verifying settings by secondary injection .........................107

Installation and commissioning manual

REC 670 ANSI

Completing the test.....................................................................119

REC 670 ANSI

Installation and commissioning manual

Measuring the operate and time limit of set values....................141

Installation and commissioning manual

REC 670 ANSI

Current circuit supervision (RDIF)...................................................156

REC 670 ANSI

Installation and commissioning manual

Scheme communication logic for distance protection (PSCH,

Installation and commissioning manual

REC 670 ANSI

Multiple command and trasmit (CM, MT).........................................202

Section 13 Primary injection testing....................................................205

Section 14 Commissioning and maintenance of the fault clearing

Section 15 Fault tracing and repair.....................................................219

REC 670 ANSI

Installation and commissioning manual

Introduction to the installation and commissioning

About the complete set of manuals for an IED

REC 670 ANSI

Installation and commissioning manual

the chronological order (indicated by chapter/section numbers) in which the protection

About the installation and commissioning manual

Installation and commissioning manual

REC 670 ANSI

The chapter Commissioning and maintenance of the fault clearing system

1MRK 511 188-UUS

Installation and commissioning manual

1MRK 511 189-UUS

Technical refernce manual

1MRK 511 187-UUS

1MRK 511 190-UUS

1MRK 511 192-BUS

Connection diagram, Single breaker

1MRK 002 801-FA